Intech Electronics CS8110 Bluetooth Car Kit User Manual MCB 8110010 0A A

In Tech Electronics Ltd Bluetooth Car Kit MCB 8110010 0A A

UserManual.wiki >

Intech Electronics >

CS8110 User Manual >

Manual HTML Version

Manual

I. Profile and Its Function……………………………………………………………….…1

I-1 Profile……………………………………………………………………….…1

I-2 Function………………………………………………………………….……2

II. How to Use! ………………………………………………………………………………3

II-1 Installation of the Hands-Free Car Kit .........….………………………..…..3

II-2 Turn on the Hands-free Car Kit.....…...…………………………………….……4

II-3 Pair the Hands-free Car Kit with Your Mobile Phone…..........……4

II-4 Establish Link………….………………………………………..……..5

II-5 External Microphone …………….......……………………..……………..……..5

II-6 Answer an Incoming Call...………………………………………………..…….6

II- Transfer Calls between This Hands-free CarKit and Your Phone..6

II-8 Make a New Call by Using Voice Dialing......…....…………………………6

II-9 Answer the call waiting .....................................…....…………………………7

II-10 Mute the Microphone …....…....…………………………………………….……7

II-11 End a Call…….......….…………………………………………………………….7

II-12 Reject a Call …….…….…………………………………………………………..7

II-13 Redial Last Dialed Number…..…………………………………….……………7

II-14 Adjust the Speaker Volume……..……………………………………………….8

II-15 Turn off the Hands-free Car Kit…...………………………………..……………8

II-16 Auto connection to the Bluetooth Mobile Phone ………………………….8

III. Maintenance and Safe Use………………………………………………………….8

IV. Accessory………………………………………………………………………………8

FCC Interference Statement…............……………..……………………………………9

Bluetooth

7 Bluetooth

Table of Content

I. Profile and Its Function

I-1 Profile (Fig.1)

. External Microphone Socket

7 Volume Up

Speaker

9. 12V Power Connector

1. Volume Down

2. LED

3. On/Off

4. External Microphone

5. Microphone plug

I-2 Function (please refer to Fig.1)

1 Volume Down

2LED

3 On/Off

External Microphone

Microphone plug

6 External Microphone Socket

Volume Up

8 Speaker

9 12V Power Connector

◎

Redial the last dialed number

Decrease the speaker volume

Answer call waiting

There are two LED colors (blue and red) to indicate the state of this Car Kit.

If you press “On / Off ”, you can:

Switch on and Off

Pair

Answer a new call

Reject a call

Make a new call using voice dialing

It allows you and your friend at the far end to speak with quality voice.

This socket is for connecting the external microphone.

Increase the speaker volume

Mute / un-mute the microphone

Connect the Car Kit with the cigarette lighter and power the Car Kit.

II. HowtoUse

Bluetooth®Hands-free Car Kit

CS8110 (BT 70P)

User Manual

Fig. 1

II-1 Installation of the Hands-free Car Kit

(please refer to Fig.2 and Fig.3)

Thank you for buying the BT 70P, Hands-free Car Kit.

Whenever you use the Hands-free Car Kit, please plug the Car Kit into the

cigarette lighter socket in your car to get the power.

Bluetooth

II-2 Turn on the Hands-free Car Kit

When the electrical system of your car is turned on and the Car Charger is

plugged into the cigarette lighter socket in your car, the Car Kit will turn on

automatically. A long tone will indicate that the hands-free Car Kit has turned

on. At the same time, blue LED will flash for a second. And then, blue LED

will keep on flashing every 3 seconds.

Note: The Car Kit can also be turned on manually by pressing and holding the

“On/Off ” key for 2 seconds when it is off.

II-3 Pair the Hands-free Car Kit with Your Mobile PhoneBluetooth

1 Put the hands-free Car Kit in pairing mode

After the Car Kit has powered on and turned on automatically, it will try to

auto reconnect the last connected mobile phone. If it fails or connects for the

first time, it will enter pairing mode immediately. A double tone will be heard.

Then the red and blue LEDs will flash alternatively, which indicates the

hands-free Car Kit has entered into the pairing mode.

Note: The Car Kit can also be put in pairing mode manually by pressing and

holding the “On/Off ” key for 5 seconds when it is off.

Fig.2

Plug the Car Kit into

the cigarette lighter

socket

Attach to the

rearview mirror

Fig.3 Clip to clothes

CS8110 / Abe

II-14 Adjust the Speaker Volume

II-15 Turn off the Hands-free Car Kit

II-16 Auto connection to the Mobile Phone

While a call is in session, pressing and releasing “Volume Up” will increase

the speaker volume, and pressing and releasing “ Volume Down ” will

decrease the speaker volume. A double tone will be heard whenever the

volume limit is reached

When the hands-free Car Kit is on, press and hold “On/Off ” for 5 seconds. A

long tone will indicate that the Car Kit starts to power off. LED continues to

flash for a few seconds. At last LED will turn off and the Car Kit is powered

off.

The Car Kit has already been paired with a Bluetooth mobile phone. If it is

turned off and turned back on again, it will search for available Bluetooth

link. If the previously paired mobile phone’s Bluetooth feature is on, the

Car Kit and the mobile phone will re-establish the Bluetooth link

automatically.

Bluetooth

1 Tomuteacall

2 Toun-muteacall

2.2 Put through the call

After the beep tone on the hands - free Car Kit, you can make a voice

dial and the call will be connected in a few seconds.

During the active call in session if another call is coming, pressing“Volume

Down” for 2 seconds will make the mobile phone switch to the waiting call

and place the active call on hold. Press “Volume Down” for 2 seconds

again, mobile phone will come back to the first active call.

Press Volume Up for about 2 seconds and a beep tone will indicate the

microphone is muted. A periodic reminder tone will be heard while the mute

function is active.

When the microphone is muted, press Volume Up for about 2 seconds.

Then the mute function will end and the periodic reminder tone will stop.

While a call is in session on the hands-free Car Kit, press “ On / Off ” and you

will disconnect the call. A long tone will indicate that the call has ended

After the call is disconnected, the blue LED will flash normally.

When the hands -free Car Kit is ringing, press “On/Off ” for 2 seconds.

Ringing will stop and a long tone will indicate that the call is rejected.

To redial the last dialed number, press “ Volume Down” for 2 seconds when

the Car Kit is standby, a beep tone will indicate an attempt to redial.

II-9 Answer the call waiting

II-10 Mute the Microphone

II-11 End a Call

II-12 Reject a Call

II-13 Redial Last Dialed Number

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this

equipment.

In-Tech declares that CS8110 (FCC ID: NV6-CS8110) is limited in CH1~CH11

for 2.4 GHz by specified firmware controlled in U.S.A.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated

with minimum distance 20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any

other antenna or transmitter.

Federal Communication Commission

Interference Statement

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one of the following measures:

II-6 Answer an Incoming Call

II-7 Transfer Calls between This Hands-free Car Kit and Your

Phone

II-8 Make a New Call by Using Voice Dialing

When an incoming call is present, the hands-free Car Kit will ring. Press “On

/ Off ” and you can answer the call. The blue LED will continue to flash once

a second while the call is in session.

When you are in session, calls can be transferred from your Phone

to the hands-free Car Kit and vice versa.

1 From Phone to the Car Kit

Press “On / Off ” once, the call will be transferred to the Car Kit.

2 From Car Kit to the Phone

Please follow the operation manual of your phone.

1.1 Press “On / Off ” on the hands-free Car Kit shortly when the Car Kit is

standby.

1.2 Put through the call

After the beep tone on the hands - free Car Kit, you can make a voice

dial by saying the name of the person on the hands-free Car Kit. The

call will be connected in a few seconds.

2.1 Press “On / Off ” on the hands-free Car Kit shortly when the Car Kit is

standby.

Bluetooth

1 When using a Mobile Phone:

2 When using a mobile phone without built-in and requiring a

dongle:

Bluetooth

Note: Make sure that the voice dialing function is properly set up in the

mobile phone and it is within the range of the hands-free Car Kit.

Note: Make sure that the voice dialing function is properly set up in the

Mobile phone and it is within the range of the hands-free Car Kit.

2 Put your mobile phone in pairing mode

3 Pair the hands-free Car Kit with your Mobile Phone

Bluetooth

2.1 Follow the operation manual of your mobile phone to start the

pairing process. Typically, this has to be done by going to a setup or

connect menu and then selecting the options to discover

devices. may take several seconds to establish a connection.

2..2 Your phone's display will indicate that it has found the new device “BT

70P ”. When you want to pair it, the phone's display would demand a

passkey or PIN, then you can enter a sequence of “0000”.

The blue LED of hands-free Car Kit will flash every 3 seconds indicating

successful pairing. The phone may also ask whether you want to change the

Car Kit's name. We recommend you should approve the name of “BT 70P ”

and do not change it.

After pairing, the mobile phone should have “connect” menu. Please select it to

establish the link. A beep tone will indicate that the Car Kit is connected. Now

you are ready to make and answer calls on the hands-free Car Kit.

Insert the microphone plug into the external microphone socket as shown in

Fig. 2.

Bluetooth

Note: Make sure if pairing does not occur as expected, turn off the hands-free

car kit and your phone, then wait for 10 seconds. Turn on them again and

repeat from Step 1 to Step 3

Note: For other phones, please follow their operation manuals to establish the

II-4 Establish Link

II-5 External Microphone

Bluetooth

link!

(please refer to Fig.2 )

III.

IV.

Maintenance and Safe Use

Accessory

◎

Use dry cloth to clean hands-free car kit!

Do not expose the car kit to liquid or moisture!

Do not expose the car kit to fire or open flames!

External Microphone (Provided)

Note:

BQB, CE and FCC approved

The word mark and logos are owned by the SIG, Inc.

And any use of such marks by In-Tech Electronics Ltd is under license. Other

trademarks and trade names are those of their respective owners.

Bluetooth Bluetooth

Bluetooth functions and operations may not be available or may vary

depending on different mobile phones.

Intech Electronics CS8110 Bluetooth Car Kit User Manual MCB 8110010 0A A

In Tech Electronics Ltd Bluetooth Car Kit MCB 8110010 0A A

Contents

Manual

Navigation menu

Namespaces

Views

Navigation