Integrated Display Technology CU328 2.4GHz FHSS Cordless Phone w/ CID, Radio and MP3 User Manual manual
Integrated Display Technology Ltd 2.4GHz FHSS Cordless Phone w/ CID, Radio and MP3 manual
User Manual
Important Saftey Instruction
Some of the following information may not apply to your
particular product; however, when using conference phone
equipment, basic safety precautions should always be followed
to reduce the risk of fire, electric shock and injury to persons,
including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the
product.
3. Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
4. This product should not be used while you are in a
bathtub, shower or pool. Immersion of the product in
water could cause an electrical shock.
5. Slots and openings in the cabinet back or bottom are
provided for ventilation, to protect it from overheating.
These openings must not be blocked or covered. The
openings should never be blocked by placing the
product on the bed, sofa, rug, or other similar surface.
This product should not be placed in a built-in
installation unless proper ventilation is provided.
6. This product should be operated only from the type of
power source indicated on the marking label. If you are
not sure of the type of power supply to your home,
consult your dealer or local power company.
7. Do not allow anything to rest on the power cord. Do not
locate this product where the cord will be abused by
persons walking on it.
8. Do not overload wall outlets and extension cords as this
can result in the risk of fire or electric shock.
9. Never push objects of any kind into this product through
cabinet slots as they may touch dangerous voltage
points or short out parts that could result in a risk of fire
or electric shock. Never spill liquid of any kind on the
product.
10. To reduce the risk of electric shock, do not disassemble
this product, but take it to a qualified serviceman
when service or repair work is required. Opening or
removing covers may expose you to dangerous voltages
or other risks. Incorrect reassembly can cause electric
shock when the telephone equipment is subsequently
used.
11. Do not expose the product to extreme temperatures
such as areas near a hot radiator or stove or in a hot car.
12. Do not place lighted candles, cigarettes, cigars, etc., on
the telephone.
13. Never touch uninsulated telephone wires or terminals
unless the telephone line has been disconnected at the
network interface.
14. Never install or modify telephone wiring during a
lightning storm.
15. Never install telephone jacks in wet locations unless the
jack is specifically designed for wet locations.
16. Use caution when installing or modifying telephone lines
to prevent electrical shock and/or fire.
17. Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
A. When the power supply cord or plug is damaged or
frayed.
B. If the product has been exposed to rain or water.
C. If the product does not operate normally by following
the operating instructions.
D. If the product cabinet has been damaged.
E. If the product exhibits a distinct change in
performance.
18. Avoid using a telephone (other than a cordless type)
during an electrical storm. There may be a remote risk of
electric shock from lightning.
19. Do not use the telephone to report a gas leak in the
vicinity of the leak.
20. Do not place this product on an unstable cart, stand or
table. The product may fall, causing serious damage to the
product.
21. Plug the adaptor to the socket-outlet which near the
equipment and shall be easily accessible.
22. Risk of explosion if battery is replaced by an incorrect
type, use on 3SN-AA120H-S-J1. Dispose of used
batteries according to the instructions
23. For servicing or replacement, you can purchase a
suitable headset through service center or retailer shop.
(see in www. oregonscientic.com)
SAFETY TIPS
This product is designed to give you years of service if handled
properly. Observe the following guidelines:
- Clean the unit with a damp cloth and mild detergent. Avoid
dropping the unit or placing it in a high-traffic location.
- Never immerse the unit in water. This can cause electrical
shock and damage the unit.
- Do not subject the Base Unit to extreme force, shock, or
fluctuations in humidity.
- Do not tamper with the internal components.
- Do not mix new and old batteries or batteries of different types.
- Remove the batteries if storing this product for a long period of
time.
- Do not scratch the LCD display.
- Do not make any changes or modifications to this product.
Unauthorized changes may void your right to use this product.
- The technical specifications for this product and the contents
of the user guide are subject to change without notice.
CAUTION
To reduce the risk of fire, use only
No. 26 AWG or larger
telecommunication line cord.
CAUTION
You must use a Class 2 power source that provide in
package. Its plug must fit the phone power jack. The supplied
adapter meets these specifications. Using an adapter that does
not meet these specifications could damage the phone or the
adapter.
Always connect the AC adapter to the phone before you connect
it to AC power. When you finish, disconnect the adapter from AC
power before you disconnect from the phone.
Under the environment with electrostatic discharge, the
captioned model may malfunction and require user reset.
SAVE THESE INSTRUCTIONS
Music Box (Cube Phone)
Model: CU328
USER MANUAL
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .
Key Features
Handset – Front View
Handset/Base – Back and Bottom View
GETTING STARTED . . . . . . . . . . . . . . . . . . . . .
Choosing a Base Unit Location
Connecting the Base Unit
Battery Set-up
Charging Handset Batteries
Low Battery Charging
Handset Reception
Handset LCD Symbols
BASIC TELEPHONE FUNCTIONS . . . . . . . . . . .
Switching to Phone Mode
Making a Call
Answering a Call
Ending a Call
Call Waiting
Message Waiting
Adjusting the Speaker Volume
Redialing a Call
Redialing from the Last 10 Numbers
Fast Redial
Deleting a Redial Number
Saving Dialed Numbers in Memory
PHONEBOOK . . . . . . . . . . . . . . . . . . . . .
Storing Numbers in the Phonebook
Keys to Use
Deleting Numbers from Phonebook
Editing Numbers in Your Phonebook
Calling Numbers from Your Phonebook
Quick Browsing of Your Phonebook
CALLER ID DISPLAY . . . . . . . . . . . . . . . .
Viewing Caller ID Records
Saving Caller ID Records in Phonebook
Deleting Caller ID Records
No Caller ID
Missed Calls. . . . . . . . . . . . . . . . . . . . . . . . ..
DURING A CALL . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Mute Function
HANDSET SETTINGS. . . . . . . . . .
Setting the Ring Tone
Setting the Ring Tone Volume
Setting the Display Language
Setting the Dial Tone
Setting the Time / Date
Setting the Time / Date Format
Setting the Alarm
Snooze / Turning the Alarm Off
Activating the Screen Saver
Delete Caller ID Records
CONFERENCE CALLS
OPERATING THE BASE UNIT
Paging the Handset
USING MULTIPLE BASE UNITS
USING MULTIPLE HANDSETS
Intercom Calling Between Handsets
Answering Intercom Calls
Call Waiting
Call Transfer Between Handsets
REGISTERING HANDSETS TO BASE UNIT
DE-REGISTERING HANDSETS
RESETTING YOUR SYSTEM
THE MP3 FUNCTIONS
Driver Installation
Connecting to Your Computer
Disconnecting From Your Computer
MP3 BASIC OPERATION . . . . . . . . . . . . . . . . . . .
Switching to Your MP3 Player
Inserting the SD Card into Your Handset
Operating Your MP3 Player
Play Mode
Setting the Sleep Timer
EQ Mode
Play Time Information
Tag Information
Volume Control
Handling Incoming Calls
THE FM RADIO . . . . . . . . . . . . . . . .
Switching to FM Radio
FM Scan Mode
Saving a Radio Station
Deleting a Radio Station
FM Preset Mode
Setting the Sleep Timer
Volume Control
HEADSET JACK
SAFETY AND CARE
Causes of Poor Reception
CHANGING THE HANDSET BATTERY
Replacing the Battery
RECYCLING NICKEL-METAL BATTERIES
SPECIFICATIONS
ABOUT OREGON SCIENTIFIC ……………….
FCC STATEMENT
Consumer Information
DECLARATION OF CONFORMITY
INTRODUCTION
Congratulations on your purchase of this Oregon
Scientific telephone. Your Cube Phone has been
carefully designed and produced by a world leader
of consumer electronic equipment
KEY FEATURES
Your 2.4GHz WDCT Cube Phone with FM radio
and MP3 player is a high-quality home
communications product with many advanced
features, such as:
• Caller ID memory that holds up to 40
numbers.
• Electronic telephone book that holds up to 50
numbers.
• Recognition of up to 4 additional handsets for
intercom calls.
• Microphone mute function.
TABLE OF CONTENTS
• Adjustable ring tones (including MP3 ring
tone), volume levels, language display,
handset IDs and low-battery / out-of-range
warning signals.
• Rechargeable batteries and up to 7-hours of
continuous talk time.
• Support for MP3 and WMA audio file formats
• Multi-format support for mass data storage
• 5 preset equalizer settings
• Multilanguage menu support
IMPORTANT: To use all of the features of this
telephone, you must subscribe to either the
standard Caller ID service or Caller ID with Call
Waiting service from your local telephone
company.
The following items should be included in the
CU328 package:
• Base unit
• Telephone audio station
• 1 AC adaptor
• Telephone line cord
• 1 battery
• Battery order sheet
• User manual
• CD-ROM (MP303S) USB driver for
Windows98®
• Stereo headset with mic
• USB cable
HANDSET – FRONT VIEW
HANDSET – FRONT VIEW
1. Number keys
2. / [DELETE] key
3. [PLAY / PAUSE] key
4. [REWIND] key
5. [INTERCOM] key
6. [STOP] key
7. [TALK] key
8. [Microphone]
9. / key
10. Track ring
11. Speaker
12. [Address Book] key
13. [FORWARD] key
14. [MUTE] key
15. Charging prongs
16. PAGE button
17. Charge / in-use indicator
HANDSET/BASE – BACK AND BOTTOM VIEW
1. USB socket
2. SD CARD slot
3. HEADSET jack
4. Radio antenna
5. POWER jack
6. TELEPHONE jack
GETTING STARTED
Certain other communication devices may use the
2.4GHz frequency for communication and, if not
set properly, these devices may interfere with your
new telephone.
CHOOSING A BASE UNIT LOCATION
When selecting a location for your base unit,
please observe the following guidelines:
• Choose a location that provides easy access
to an AC power source and telephone jack.
• Do not place the base unit near a sink,
bathtub or shower, or close to heat sources.
• Do not place the base unit near large metal
objects or electronic appliances that may
cause radio interference.
CONNECTING THE BASE UNIT
To connect the base unit:
1. Plug the AC adaptor into the power jack on
the bottom of the base, and then plug the
other end into an electrical outlet (see below).
2. Plug the telephone line cord into the
telephone line jack on the bottom of the base
unit, and then plug the other end into your
phone jack.
BATTERY SETUP
To install the battery in your handset:
1. Open the battery compartment cover located
at the bottom of the handset.
2. Plug the battery connector into the socket.
3. Place battery in the battery compartment.
4. Replace the battery compartment cover by
sliding it into place. (The cover clicks into
place when it is secured).
NOTE: The handset comes with the battery
already installed.
CHARGING HANDSET BATTERIES
You must charge the handset batteries for 15
continuous hours the first time you use them.
When the battery icon in the top right corner on the
LCD screen appears empty, or if you hear a
warning beep during a call, please:
• End the call as soon as possible.
• Charge the handset by putting it back on the
base cradle. (The handset will begin to beep
to indicate that the handset is charging).
LOW BATTERY CHARGING
When the battery is low and has only 15 minutes
of talk time left, the handset will beep a warning
tone and the LCD display will flash “Low Battery”.
When this happens, please end the call as soon
as possible, and put the handset back on the
charger until the battery symbol returns to high
level.
HANDSET RECEPTION
Usually, a loss of reception means you are too far
from the base unit, or there is interference
between the base unit and handset. Make sure to:
• Stay within a range of 300 meters (984 feet)
from the base unit while using the handset.
• Avoid interference such as TV or other
electrical appliances.
NOTE: If your handset is out of range of the base
unit, the range symbol starts flashing.
HANDSET LCD SYMBOLS
Within range indicator
Flashing when out of range
Ringer is set to OFF
EXT Line-in-use
Missed call
Battery (5 levels)
Flashing when battery is low
(level 1 )
BASIC TELEPHONE FUNCTIONS
While operating your Cube Phone, if you want to
escape from the menu or the current mode, press
.
NOTE: The following instructions are for the
Phone Mode.
SWITCHING TO PHONE MODE
To change to Phone Mode:
1. Press /, then use or
to select “Goto Phone”.
2. Press /.
NOTE: When you enter the Phone Mode, the
telephone icon will appear at the top of
your LCD display.
MAKING A CALL
To make a call, press to get the dial tone,
and then dial the number. (If you make a mistake,
press again to cancel the whole number).
OR
Dial the number, then press .
ANSWERING A CALL
The handset will ring when there is an external
call.
To answer a call, press .
To answer a call while music is playing, press
. (The audio will pause automatically).
ENDING A CALL
To end a call, simply press .
CALL WAITING
When you hear a call waiting tone, press
/ to switch from an existing call, to call
waiting.
NOTE: You must subscribe to this service from
your local telephone company.
MESSAGE WAITING
When someone has called and left you a
message, “Message Waiting” will appear on the
screen. Follow the voice message commands to
access message.
ADJUSTING THE SPEAKER VOLUME
To adjust the speaker volume:
1. Press .
2. Then turn the track ring to adjust the speaker
volume accordingly.
REDIALING A CALL
To redial a call, press , and then press
/ .
REDIALING FROM THE LAST 10 NUMBERS
To redial from the last 10 numbers:
1. Press / to see your last call
record.
2. Use , or the track ring to select a
number.
3. Press to dial the number.
If you want to edit the phone number before
redialing:
1. Press /.
2. Press /.
3. Use , or the track ring to select
“Edit for Call”, then press /.
4. Use / and 0-9 buttons to edit the
number.
5. Press to dial the number.
FAST REDIAL
When you make a call and hear the busy tone,
press /. The phone will quickly redial
the number within 3 seconds.
DELETING A REDIAL NUMBER
To delete a redialed number:
1. Press / to see your last call
record.
2. Use , or the track ring to select a
number, then press /.
3. Select “Delete Record” to delete 1 number,
or “Delete All” to delete all numbers.
4. Press /.
5. Select “Yes”, then press / to
confirm.
SAVING DIALED NUMBERS INTO MEMORY
The handset will automatically save the last 10
numbers you dialed.
To save dialed numbers into your phonebook:
1. Press /. (The last number is
listed).
2. Use , or the track ring to select a
phone number, then press /.
3. Select “Save Phonebook” to save number,
then press /. (“Saved” will
appear on the screen to confirm the action).
PHONEBOOK
Your phone can store 50 phone numbers.
STORING NUMBERS IN THE PHONEBOOK
To store a number in your phonebook:
1. Press /.
2. Use , or the track ring to select
“Phone Book”, then press /.
3. The handset display shows a record or
“---Empty---“. Press /.
4. Use , or the track ring to select
“Add Record”.
5. Enter the name and then press /
to confirm.
6. Enter the name (see KEYS TO USE below)
and then press /.
7. Enter the phone number and then press
/. The handset will beep twice
indicating that the record has been stored.
NOTE: If only a phone number and no name is
input, then the record can still be saved.
KEYS TO USE
When entering a name, “B” will be entered by
pressing the “2” button once, followed by pressing
“2” again within 1 second. If pressed beyond 1
second, “A” is entered and the second press of “2”
will give the entry of “AA”.
[PLEASE LAY OUT IN CHART FORMAT]
The list of characters is shown below:
CAPITAL LETTERS SMALL LETTERS
1 SPACE 1 _ - + = ^ ~ . , ; : ? ! SPACE 1 _ - + = ^ ~ . , ; : ? !
2 ABC2ÄÆÅÀÁÂÃÇ abc2äæåàáâãç
3 DEF3ÈÉÊËÐ def3èéêëð
4 GHI4ÌÍÎÏ ghi4ìíîï
5 JKL5 jkl5
6 MNO6ÖØÒÓÔÕÑ mno6öøòóôõñ
7 PQRS7 pqrs7
8 TUV8ÙÚÛÜ tuv8ùúûü
9 WXYZ9ÝÞ wxyz9ýþ
0 0 * # $ & % / \ | ( ) [ ] < > 0 * # $ & % / \ | ( )[ ] < >
• Press when editing a name to return to Standby Mode.
Press when editing a number to get “*”.
# Press to change between capital and small letters.
DELETING NUMBERS FROM PHONEBOOK
To delete a record in your phonebook:
1. Press /.
2. Use , or the track ring to select
“Phone Book”, then press /.
3. The handset display shows a record. Use
, or the track ring to select the
record you want to delete. Press
/.
4. Enter the name (see KEYS TO USE section)
and then press /.
5. Use , or the track ring to select
“Delete Record”.
6. Press /.
7. Select “Yes” to complete deletion. The
handset will beep twice indicating that the
record has been deleted.
To delete all records:
1. Follow steps 1-4 above and select “Delete
All?”
2. Now follow steps 6-7 above.
EDITING NUMBERS IN YOUR PHONEBOOK
To edit a record in your phonebook:
1. Press /.
2. Use , or the track ring to select
“Phone Book”, then press /.
3. Press / again, and then use
, or the track ring to select “Edit
Record”.
4. Press /. Use / to edit
the name. (See KEYS TO USE section) and
then press /.
5. Use / to edit the number and then
press /. The handset will beep
twice indicating that the record has been
stored.
CALLING NUMBERS FROM PHONEBOOK
To call using a number in your phonebook:
1. Press /.
2. Use , or the track ring to select
“Phone Book”, then press /.
3. Use , or the track ring to select a
number, then press to dial the number.
QUICK BROWSING OF YOUR PHONEBOOK
To browse through your phonebook quickly:
1. Press and then use or to
browse through your phonebook.
2. Then press the key with the 1st letter of the
person’s name you are looking for. (For
example, press key 7, 4 times to get quick
access to a name beginning with ‘S’).
Press to dial the selected number, or press
to return to Standby Mode.
NOTE: You can use the phonebook function while
on an active call.
CALLER ID DISPLAY
If you have subscribed to this service, the caller’s
phone number will display when there is an
incoming call.
NOTE: If the caller’s phone number was stored in
the phonebook, the associated name will be
displayed with the phone number.
Each entry in the caller list has the:
• Caller number (up to 24 digits)
• Caller name (up to 15 characters
• Date and time of the call
• Number of calls made to this number (up to
40).
VIEWING CALLER ID RECORDS
To view caller ID records:
1. When the phone is in Standby Mode use
, or the track ring to browse
through Caller ID records.
2. If you need to edit the phone number before
making the call press /.
3. Use , or the track ring to select
“Edit for Call”.
4. Use / and 0-9 buttons to edit the
number.
5. Press to dial the number.
NOTE: If “No Calls” appears on the screen, then
no records are stored in the Caller ID memory.
NOTE: When the Caller ID memory is full, it will
automatically delete your 1ST Caller ID record.
SAVING CALLER ID RECORDS IN YOUR
PHONEBOOK
When you have a Caller ID record on your screen:
1. Press /, then use , or
the track ring to select “Save Phonebook”.
2. Press /. “Saved” will appear on
the screen to confirm the action.
DELETING CALLER ID RECORDS
To delete a record:
1. Press , or the track ring whilst in
Standby Mode and select the number you
want to delete. Then, press /.
2. Select “Delete Record”, then press
/.
3. Select “Yes”, then press / to
confirm.
To delete all records:
1. Press , or the track ring whilst in
Standby Mode. Then, press /.
2. Select “Delete All”, then press /.
3. Select “Yes”, then press / to
confirm.
NO CALLER ID
If a caller has withheld their Caller ID name and /
or number, one of the following messages will
appear on your screen:
• “Blocked Number”
• “Unknown Number”
• “Blocked Name”
• “Unknown Name”
• “Unknown Caller”
• “Blocked Call”
MISSED CALLS
If you miss a call, the handset will display: .
When you view the Caller ID of your missed calls,
the following notifications will appear on the
screen:
• “NEW” – This is the first missed call from this
particular Caller ID.
• “REPT” – This appears when more than one
call has been missed from this particular
Caller ID.
DURING A CALL
USING THE MUTE FUNCTION
To mute the handset, press .
To un-mute the handset, press again. You
will return to the normal mode.
HANDSET SETTINGS
IMPORTANT:
• If you press the button, you will enter
Talk Mode.
• If you press the / button, you will
enter Menu Mode.
• You cannot enter the Menu Mode when the
phone is in Talk Mode. To exit the Talk Mode
press .
• To leave a setting at any time and return to
Standby Mode, press the button.
NOTE: When you have completed a setting, 2
beeps will sound to indicate that the task is
complete.
SETTING THE RING TONE
You have a choice of 10 polyphonic melodies, 4
tones and MP3 songs for incoming calls.
To select a ring tone:
1. Press /, then use , or
the track ring to select “Sound & Display”.
2. Press /.
3. Select “Ringer Tone”, then press
/.
4. Select the melody or tone you prefer, then
press / to confirm. You will here a
demonstration of the tone/song selected.
SETTING THE RING TONE VOLUME
To set the ring tone volume:
1. Press /, then use , or
the track ring to select “Sound & Display”.
2. Press /, then use , or
the track ring to select “Ringer Volume”.
3. Use , or the track ring to increase
or decrease the volume.
4. Then press / to confirm.
NOTE: If the ring volume is turned off, you will see
the icon.
SETTING THE DISPLAY LANGUAGE
To change the language:
1. Press /, then use , or
the track ring to select “Phone Setup”.
2. Press /, then use , or
the track ring to select “Language”, then
press /.
3. Select the language you want, then press
/ to confirm.
NOTE: The default language for the handset
display is English. You can also change the
language to French, Spanish, German, Italian,
Dutch, Portuguese, Swedish, Finnish, Danish or
Norwegian.
SETTING THE DIAL TONE
In order to provide compatibility with other phone
systems, your phone can be set to either Pulse
dialing (same as rotary dial phones), or Tone
dialing (DTMF).
To set the Dial Mode:
1. Press /, then use , or
the track ring to select “Phone Setup”.
2. Press /, then use , or
the track ring to select “Dialing”.
3. Press /.
4. Select either “Tone” or “Pulse” mode, then
press / to confirm.
SETTING THE TIME / DATE
To set the time / date format:
1. Press /, then use , or
the track ring to select “Clock & Timer”.
2. Press /.
3. Select “Date & Time”, then press
/.
4. Select “Set Time” or “Set Date”, then press
/.
5. Use the number keys to set the time/date.
(Use , or the track ring to select
hour or minutes to set).
6. Press / to confirm.
SETTING THE TIME / DATE FORMAT
To set the time / date format:
1. Press /, then use , or
the track ring to select “Clock & Timer”.
2. Press /.
3. Select “Date & Time”, then press
/.
4. Select either “Time Format” or “Date
Format”, then press /.
5. Use the number keys to set the alarm time.
(Use , or the track ring to select
hour or minutes to set).
6. Press / to confirm.
SETTING THE ALARM
Your Cube Phone comes with dual alarm
functionality.
To set the alarm:
1. Press /, then use or
to select “Clock & Timer”.
2. Press /.
3. Select “Alarms”, then press /.
4. Select Alarm1 or Alarm2, then press
/.
5. Use the number keys to set the alarm time.
(Use , or the track ring to select
hour or minutes to set).
6. Press / to confirm.
NOTE: You can select Alarm 1, 2, 3, 4 or radio.
NOTE: The alarm will be set automatically upon
confirmation.
SNOOZE / TURNING THE ALARM OFF
Once an alarm sounds, you may, press any key
once and the alarm will snooze for 8 minutes.
OR
Press and hold to turn off the alarm.
NOTE: If no button is pressed for 2 minutes the
alarm will turn itself off.
ACTIVATING THE SCREEN SAVER
The screensaver shows the time on your LCD
Display.
To activate your screensaver:
1. Press /, then use , or
the track ring to select “Screensaver”.
2. Press /.
3. Select “On”, then press / to
confirm.
NOTE: It will take 12 minutes for the screensaver
to be activated after confirmation.
DELETE CALLER ID RECORDS
To delete all Caller ID records:
1. Press /, then use , or
track ring to select “Erase All CID”, then
press /.
2. Select “Yes” or “No”, then press
/.
CONFERENCE CALLS
You can have a conference call with an external
party and 2 internal parties.
To have a conference call:
1. First establish the call with the external party
by either making an external call or answering
an incoming call.
2. Press to make an intercom call to
another handset. (The external party will be
put on hold. The internal party answers your
intercom call by pressing ).
3. Then you press and hold for about 2
seconds (you will hear a confirmation key
tone).
You, the external party and the other internal party
can talk together in a conference call.
OPERATING THE BASE UNIT
PAGING THE HANDSET
To look for your handset, press the PAGE button
in the cradle of the base unit.
To stop the paging, press any button once.
USING MULTIPLE BASE UNITS
Your handset can select 1 of 4 base units:
1. Press /, then use , or
the track ring to select “Handset Settings”.
2. Press /.
3. Use , or the track ring to select
“Select Base”, then press /.
4. Use , or the track ring to choose
automatic selection or base unit 1-4, then
press /.
NOTE: When “Automatic” is selected, the
handset will select a free base unit for you.
USING MULTIPLE HANDSETS
Your base unit can synchronize with up to 4
handsets.
INTERCOM CALLING BETWEEN HANDSETS
To call between handsets:
1. Press on your handset.
2. Type in the number of the handset (1-4) that
you want to reach.
3. The paged handset will ring. The display of
the paged handset will show “Int Call”.
NOTE: To cancel the intercom call, press .
ANSWERING INTERCOM CALLS
To answer an intercom call, press .
To end an intercom call, press again to end
the intercom call.
CALL WAITING
If an external call comes in during an intercom
conversation, you will hear a call waiting tone.
To end an intercom call:
1. Press . (The external line will ring).
2. Press again to answer the external call.
CALL TRANSFER BETWEEN HANDSETS
You can transfer an external call from one handset
to another.
To transfer a call between handsets:
1. During an external phone conversation, press
. Your caller will be put on hold.
2. Type in the handset number (1-4) to which
you want the call transferred.
3. The paged handset will ring and “Int Call”
will appear on the display.
4. To answer the call on the paged handset,
press .
5. Press on the paging handset to transfer
the call.
NOTE: If the other handset does not answer,
press to end the intercom call and get
back to the external line. Pressing will end
both the intercom call and the external call.
REGISTERING HANDSETS TO BASE UNIT
The handset and base unit are factory
pre-registered with each other. When you
purchase an additional handset, you have to
register it to the base unit in order to make and
answer calls.
You can register up to 4 more handsets to make
and answer calls via the same base unit.
Handsets are numbered 1 to 4.
To register a new handset:
1. Press and hold the PAGE button on the
cradle of the base unit to enter Registration
Mode.
2. On the handset, press /.
3. Use , or the track ring to select
“Handset Setting”, then press /.
4. Select “Registration”, then press
/.
5. Use , or the track ring to select
“Base 1, 2, 3 or 4”, then press /.
6. Enter the default Pin Code “0000” then press
/.
7. You will see the message: “Registering”.
8. When the registration is complete,
“Registration Success” will appear on the
screen.
NOTE: The base unit will then send a signal to the
handset registering the handset to the base unit.
Once the registration function has been
completed, the handset will return to Standby
Mode.
DE-REGISTERING HANDSETS
To de-register a handset from the base unit:
1. On the handset, press /.
2. Use and to select “Handset
Setting”, then press /.
3. Select “Remove HS”, then press
/.
4. Use and to select handset
number, then press /.
5. “Confirm?” appears on the screen. Press
/ and “Handset Removed” will
appear to confirm de-registration.
NOTE: You cannot de-register the handset you
are using.
RESETTING YOUR SYSTEM
If you need to reset your system, you will lose any
information you have stored and all settings will
return to their default settings.
To reset your system to the default settings:
1. Press /, then use and
to select “Handset Setting”.
2. Press /.
3. Select “Set Default”, then press
/.
4. When prompted, select “Yes”. You will then
hear the double beep to indicate the default
settings have been restored.
Your default settings are:
• Language: English
• INT melody: Melody 1
• Handset name: Handset
• Ring volume: 3
• Dial mode: Tone
• Battery indicator: On
• Ear volume: 1
• Range indicator: On
THE MP3 FUNCTIONS
Your CU328 comes with a built-in MP3 player,
which supports multiple audio standards, such as
WMA (Windows Media AudioTM Version 8) and
MP3 formats. You can also transfer files easily via
a USB2.0 TM connection.
Please ensure your computer meets the following
minimum system requirements:
• Intel ® Pentium ® 133MHz or faster
• CD-ROM Drive
• USB1.1 port or USB2.0 port
• 10MB free hard disk space
• Microsoft ® Windows ®, 98SE, ME, 2000 or
XP
• Mac OS 9.0 or above
DRIVER INSTALLATION
Windows® ME, 2000, XP Users
Windows® already provides the USB driver.
Windows 98SE Users
Installing the MP3 driver software is necessary.
To install the MP3 driver software:
1. Insert the MP3 CD-ROM into your computer.
2. Follow the on-screen instructions.
3. Restart your computer.
CONNECTING TO YOUR COMPUTER
Insert the USB cable to the USB port in your PC
and connect the mini-USB connector to your USB
port. The unit will automatically begin charging.
IMPORTANT: Do not disconnect while
downloading data from your PC.
DISCONNECTING FROM YOUR COMPUTER
Please follow the procedures below.
For Windows 98SE:
1. Double click the My Computer icon.
2. Right click the removable drive letter your
player has been assigned.
3. Click “Eject” from list before disconnecting.
For Windows ME, 2000, XP:
Before disconnecting, click the "Stop USB Mass
Storage Device" icon on the Windows
taskbar at the bottom right of your computer
screen to stop the device.
For Macintosh:
Drag and drop the “Untitled” icon from the
desktop to the “Trash” icon to eject the player
before disconnecting.
NOTE: Before unplugging your player from your
computer, wait at least 15 seconds after the audio
or data file transfer is completed to prevent any
data loss that may occur.
MP3 BASIC OPERATION
SWITCHING TO YOUR MP3 PLAYER
To switch to MP3 Mode:
1. Press /, then use or
to select “Goto MP3”.
2. Press /.
NOTE: The MP3 player functionality will not work
unless you have inserted the SD card into the SD
socket at the back of the handset.
NOTE: To escape from the menu or the current
mode, press .
INSERTING THE SD CARD INTO HANDSET
The SD card stores files downloaded from your
computer via the USB cable.
To insert the SD card into your handset:
1. Locate the SD socket at the back of the
handset, and insert the SD card with the
“clipped” corner on the top right.
2. Push the SD card into the socket all the way.
(You will hear a click; this indicates that the
card is in place).
To remove the SD card from the handset:
1. Push the SD card inwards until you hear the
clicking sound that indicates that it will
self-eject.
2. Pull the SD card from the slot.
NOTE: The SD card capability is up to 1 GB only.
NOTE: Any songs you downloaded from your
computer while the SD card was inside your
handset will be stored in your SD card. Therefore
make sure you protect the SD card from moisture
and damage.
OPERATING YOUR MP3 PLAYER
The operation of your MP3 player is simple and
intuitive.
To play a song, while in the MP3 Mode, press
.
To stop a song, press . (This button is at the
bottom of the silver volume ring).
To pause a song, press .
To fast forward through a track, press and hold
. If you want to skip more than the current
track, press and hold the button.
To rewind to a previous track, press and hold
. If you want to rewind back to more than the
previous track, press and hold the button.
PLAY MODE
You have a number of choices of how to play your
songs, including:
• Repeat All – Plays all audio files over and
over in chronological order.
• Repeat One – Plays the selected audio file
continuously.
• Random Repeat – This setting will repeat
randomly selected audio files.
• Random – Plays audio files that are selected
randomly.
• Normal – Plays all audio files in
chronological order.
To switch to Play Mode while in MP3 Mode:
1. Press /.
2. Use , or the track ring to select
“Play Mode”.
3. Press / .
4. Once you are in Play Mode, simply use ,
or the track ring to select the mode of
your choice.
5. Once you have selected, press / .
SETTING THE SLEEP TIMER
The Sleep Timer is designed to automatically shut
off audio after a certain period of time. (This
feature enables you to fall asleep with the music
on without having it play all night).
To set the sleep timer function:
1. Press /.
2. In the MP3 Mode (or Radio Mode), use ,
or the track ring to select “Sleep
Timer”, then press /.
3. Use , or the track ring to select a
timer setting, then press /. (2
beeps will sound to confirm selection).
EQ MODE
You have a number of choices of how to equalize
your music, including:
• Classic – Affects sound to enhance all
classical music.
• Live – Affects sound to enhance all live
music.
• Pop – Affects sound to enhance pop music.
• Rock – Affects sound to enhance rock music.
• Normal – No audio settings set to enhance
sound.
To switch to EQ Mode while in MP3 Mode:
1. Press /.
2. Use , or the track ring to select
“EQ Mode”.
3. Press / .
4. Once you are in EQ Mode, simply use ,
or the track ring to select the mode of
your choice.
5. Once you have selected, press / .
PLAY TIME INFORMATION
You have two choices of how to display your play
time information, which include:
• Elapse – Shows time passed since
beginning of audio file.
• Remain - Shows time to play until audio file
finishes.
To switch to Play Time Information Mode while in
MP3 Mode:
1. Press /.
2. Use , or the track ring to select
“Play Time Info”.
3. Press / .
4. Once you are in Play Time Info Mode, simply
use , or the track ring to select the
time display of your choice.
5. Once you have selected, press / .
TAG INFORMATION
You have two choices of how to tag your files in
your MP3 player: ON or OFF.
To switch to Tag Info Mode while in MP3 Mode:
1. Press /.
2. Use , or the track ring to select
“Tag Info”.
3. Press / .
4. Once you are in Tag Info Mode, simply use
, or the track ring to select “On” or
“Off”.
5. Once you have selected, press / .
VOLUME CONTROL
To adjust the volume, move the track ring
clockwise to increase the volume, or
counter-clockwise to decrease the volume.
HANDLING INCOMING CALLS
When there is an incoming call while the user is
listening to the MP3 or Radio, the Cube Phone
will pause playing automatically.
To receive an incoming call while music is on,
press .
After the call ends, your Cube Phone will return to
the MP3 or FM Mode.
THE FM RADIO (87.5 – 108MHz)
You can preset up to ten radio stations in your
telephone. Pull out the antenna located at the
back of the handset to maximize your reception).
SWITCHING TO FM RADIO
To switch to the FM Mode:
1. Press /, then use , or
the track ring to select “Goto FM”.
2. Press /.
NOTE: When you enter the FM Mode, the radio
icon will appear at the top of your LCD
display.
FM SCAN MODE
To get to the FM Scan Mode while in FM Mode:
1. Press /.
2. Use , or the track ring to select
“FM Scan Mode”.
3. Press /.
4. Once you are in FM Scan Mode, simply use
or to find a FM station, or press
and hold or to search
automatically for a FM station with good
reception.
SAVING A RADIO STATION
To save a radio station:
1. Press /.
2. Use or to select “Save
Stations”.
3. Press /.
4. Once you are in Save Stations Mode, simply
use or to select a channel from a
list of ten stations (channels).
5. Press / to save the selected
radio station.
DELETING A RADIO STATION
To delete a radio station:
1. Press /.
2. Use or to select “Delete
Stations”.
3. Press /.
4. Use or to select a channel from
the list of ten stations (channels).
5. Press / to delete the selected
station.
NOTE: The deleted radio station will disappear
from the list, but when you enter the “Save
Stations” Mode, the channel will be listed but will
show “---Empty---“.
FM PRESET MODE
To get to the FM Preset Mode while in FM Mode:
1. Press /.
2. Use or to select “FM Preset
Mode”.
3. Press /.
4. Once you are in FM Preset Mode, simply use
or to select a preset radio station
from the list of ten stations (channels). The
radio will then play.
NOTE: The LCD display will show the channel
number under the word “Preset”.
SETTING THE SLEEP TIMER
Please see SETTING THE SLEEP TIMER in the
MP3 BASIC OPERATIONS section of this
manual.
VOLUME CONTROL
The volume works the same way as for the MP3
player. (See VOLUME CONTROL in the MP3
BASIC OPERATIONS section).
HEADSET JACK
A headset can be used with your telephone for
hands-free conversation.
To use a headset, plug it into the HEADSET jack
located at the back of the handset.
While the headset is connected, press to
answer or place a call.
NOTE: The headset is worn with the strap around
the back of the head, not around the top of the
head.
SAFETY AND CARE
This product is designed to give you years of
service if handled properly. Please observe the
following guidelines:
• Do not subject the main unit to extreme force,
shock or fluctuations in humidity.
• Do not make any changes or modifications to
this product. (Unauthorized changes may
void your right to use the product).
• Keep your player away from any strong
magnetic fields. Exposure to magnetic fields
may cause the memory to be erased or even
damaged.
• Do not expose your telephone to direct
sunlight or moisture.
• Clean the phone with a soft cloth, but never
use a strong cleaning agent or abrasive
powder. This will damage the finish.
• Periodically clean the charge contacts on the
handset and base unit with a clean pencil
eraser.
FM RADIO
Causes of poor reception:
• Aluminum siding
• Foil backing on insulation
• Heating ducts and other metal construction
shielding radio signals
• You are too close to appliances, such as
microwaves, stoves or computers
• Atmospheric conditions, such as strong
storms
• Base unit is installed in the basement or lower
floor of the house
• Base unit is plugged into an AC outlet with
other electronic devices
• Handset battery is low
• You are out of the base unit’s transmission
range
NOTE: If you are having poor reception, be sure to
pull out the antenna at the back of the unit.
CHANGING THE HANDSET BATTERY
When the handset operating time becomes short
even after a battery has been recharged, please
replace the battery. With normal usage, your
battery should last about one year.
REPLACING THE BATTERY
1. Make sure the telephone is turned OFF.
2. Slide off the battery compartment cover.
3. Disconnect the battery plug from the jack in the
compartment and remove the battery pack.
4. Insert the new battery pack and connect the
cord into the jack.
5. Put the battery compartment cover back on.
6. Place handset on the base to charge the new
battery for 15 hours.
CAUTION: To reduce the risk of fire or personal
injury, use a 3.6 V, 1200mAh battery. Contact your
place of purchase.
RECYCLING NICKEL-METAL HYDRIDE
BATTERIES
Nickel-metal hydride batteries must be disposed
of properly.
Please take your used battery pack to a store that
recycles Ni-MH batteries.
SPECIFICATIONS
Here are the specifications for your Cube Phone:
TYPE DESCRIPTION
Standard Worldwide Digital
Cordless
Telecommunication
(WDCT)
Frequency range 2.4GHz ISM
Channel bandwidth 0.824MHz
Modulation GFSK
Speech coding Adaptive Differential Pulse
Code Modulation
(ADPCM)
Communication
range Up to 300 meters in open
space
Base power supply Input 120V / 60Hz
Handset charger
power supply Input 120V / 60Hz
Languages 11 languages
Handset battery
charging time 15 hours (approx.)
Standby: 5 days (approx.) Operating time Talk: 7 hours (approx.)
Operating
temperature 0°C to 45°C
Storage temperature
(outdoor)
Storage temperature
(indoor)
Humidity range
-20°C to 60°C
-5°C to 50°C
25% to 90%
NOTE: The technical specifications for this
product and the contents of the user guide are
subject to change without notice.
ABOUT OREGON SCIENTIFIC
Visit our website (www.oregonscientific.com) to
learn more about Oregon Scientific products such
as digital cameras; MP3 players; children's
electronic learning products and games;
projection clocks; health and fitness gear;
weather stations; and digital and conference
phones. The website also includes contact
information for our customer care department in
case you need to reach us, as well as frequently
asked questions and customer downloads.
We hope you will find all the information you need
on our website, however if you're in the US and
would like to contact the Oregon Scientific
Customer Care department directly, please visit:
www2.oregonscientific.com/service/support
OR
Call 949-608-2848.
For international enquiries, please visit:
www2.oregonscientific.com/about/international/d
efault.asp
FCC STATEMENT
This device complies with Part 15 of the FCC
Rules. Operation is subject to the conditions that
this device does not cause harmful interference.
WARNING: Changes or modifications to this unit
not expressly approved by the party responsible
for compliance could void the user authority to
operate the equipment.
NOTE: This equipment has been tested and
found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation.
This product meets the applicable Industry
Canada technical specifications.
This equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment off
and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio /
TV technician for help.
CONSUMER INFORMATION
a. This equipment complies with Part 68 of the
FCC rules and the requirements adopted by
the ACTA. On the bottom of this equipment
is a label that contains, among other
information, a product identifier in the format
US:KT5W400BCU328. If requested, this
number must be provided to the telephone
company.
b. An applicable certification jack Universal
Service Order Codes (USOC) for the
equipment is provided (i.e., RJ11C) in the
packaging with each piece of approved
terminal equipment. The mounting of the
approval unit in the final assembly must be
made so that the approved unit is isolated
from exposure to any hazardous voltages
within the assembly. Adequate separation
and restraint of cables and cords have been
provided
c. A plug and jack used to connect this
equipment to the premises’ wiring and
telephone network must comply with the
applicable FCC Part 68 rules and
requirements adopted by the ACTA. A
compliant telephone cord and modular plug
is provided with this product. It is designed to
connect to a compatible modular jack that is
also compliant. See installation instructions
for details.
d. The REN is used to determine the number of
devices that may be connected to a
telephone line. Excessive RENs on a
telephone line may result in the device not
ringing in response to an incoming call. In
most but not all areas, the sum of RENs
should not exceed five (5.0). To be certain of
the number of devices that may be
connected to a line, as determined by the
total RENs, contact the local telephone
company. [For products approved after July
23, 2001, the REN for this product is part of
the product identifier that has the format
US:KT5W400BCU328. The digits
represented by ## are the REN without a
decimal point (e.g., 03 is a REN of 0.3). For
earlier products, the REN is separately
shown on the label].
e. If this equipment CU328 causes harm to the
telephone network, the telephone company
will notify you in advance that temporary
discontinuance of service may be required.
But if advance notice isn't practical, the
telephone company will notify the customer
as soon as possible. Also, you will be
advised of your right to file a complaint with
the FCC if you believe it is necessary.
f. The telephone company may make changes
in its facilities, equipment, operations or
procedures that could affect the operation of
this equipment. If this happens the telephone
company will provide advance notice in order
for you to make necessary modifications to
maintain uninterrupted service.
g. Should you experience trouble with this
equipment, please contact Oregon Scientific
www2.oregonscientific.com/service/support
or call 1-800-853-8883 for repair or warranty
information. If the equipment is causing harm
to the telephone network, the telephone
company may request that you disconnect
the equipment until the problem is resolved.
h. Please follow instructions for repairing if
needed (e.g. REPLACING THE BATTERY
section); otherwise do not alter or repair any
parts of THE device except where specified.
i. Connection to party line service is subject to
state tariffs. Contact the state public utility
commission, public service commission or
corporation commission for information.
NOTICE If your home has specially wired alarm
equipment connected to the telephone line,
ensure the installation of this CU328 does not
disable your alarm equipment. If you have
questions about what will disable alarm
equipment, consult your telephone company or a
qualified installer.
NOTICE According to telephone company reports,
AC electrical surges, typically resulting from
lightning strikes, are very destructive to telephone
equipment connected to AC power sources. To
minimize damage from these types of surges, a
surge arrestor is recommended.
This equipment is to be supplied from an
identified USB port complying with the
requirements of Limited Power Source.
CAUTION
To maintain compliance with the FCC's RF
exposure guidelines place the base unit at least
20cm from the nearby persons."
DECLARATION OF CONFORMITY
"Hereby, Oregon Scientific declares that this
Cube Phone (CU328) is in compliance with
the essential requirements and other
relevant provisions of Directive 1999/5/EC. A
copy of the signed and dated Declaration of
Conformity is available on request via our
Oregon Scientific Customer Service."
2.4GHz Cube Phone With
MP3 Player and FM Radio
Model: CU328
User Manual