Intel Mobile Communications 31308 Bluetooth EDR module User Manual UniStone Product Specification

Intel Mobile Communications GmbH Bluetooth EDR module UniStone Product Specification

manual

UniStoneImportant Application InformationProduct Specification 208 T3130-8XV10T4-7600, 2006-12-18CONFIDENTIAL9 Important Application Information9.1 Reference designFigure 9-1 Reference design schematics*n.p. means that the component is not mounted (i.e. not placed)
UniStoneImportant Application InformationProduct Specification 209 T3130-8XV10T4-7600, 2006-12-18CONFIDENTIALPBA 31308 is intended to be installed inside an end user equipment. PBA 31308 isBluetoooth, R&TTA and FCC qualified with the reference design described in Figure 9-1 togheter with the following antenna:Manufacturers of mobile, fixed or portable devices incorporating this device are advisedto clarify any regulatory questions and to have their complete product tested andapproved for compliance (FCC or other when applicable). There are no parts in PBA 31308 that can be modified by the user except modificationsof the device BD data and loading of SW patches. Any changes or modifications madeto this device that are not expressly approved by Infineon, may void the user’s authorityto operate the equipment.9.2 FCC Class B digital devices regulatory noticeThis equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. Thisequipment generates, uses, and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, theuser is encouraged to try to correct the interference by 1 or more of the followingmeasures:• Reorient or relocate the antenna• Increase the separation between the equipment and receiver• Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected• Consult the dealer or an experienced radio or television technician for help9.3 FCC Wireless noticeThis product emits radio frequency energy, but the radiated output power of this deviceis far below the FCC radio frequency exposure limits. Nevertheless, the device shouldbe used in such a manner that the potential for human contact with the antenna duringnormal operation is minimized. To meet the FCC's RF exposure rules and regulations:Make Model Peak antenna gain ImpedancegigaAnt Titanis 4 - 4.4 dBi 50 ohm
UniStoneImportant Application InformationProduct Specification 210 T3130-8XV10T4-7600, 2006-12-18CONFIDENTIAL• The system antenna(s) used for this transmitter must not be co-located or operatingin conjunction with any other antenna or transmitter.• The system antenna(s) used for this module must not exceed 4 dBi.• Users and installers must be provided with antenna installation instructions andtransmitter operating conditions for satisfying RF exposure compliance.Manufacturers of mobile, fixed or portable devices incorporating this module are advisedto clarify any regulatory questions and to have their complete product tested andapproved for FCC compliance.9.4 FCC Interference StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the followingtwo conditions: (1) this device may not cause harmful interference, and (2) this devicemust accept any interference received, including interference that may cause undesiredoperation.9.5 FCC IdentifierFCC ID: Q2331308 9.6 European R&TTE declaration of conformity Hereby, Infineon Technology AG, declares that the Bluetooth module PBA 31308 is incompliance with the essential requirements and other relevant provisions of Directive1999/5/EC.As a result of the the conformity assessment procedure described in Annex III of theDirective 1999/5/EC, this equipment will be labelled as follows:PBA31308 in the specified reference design can be used in the following countries:Austria, belgium, Cyprus, Czech republic, Denmark Estonia, Finland, France, Germany,Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Poland, Portugal,Slovakia, Slovenia, Spain, Sweden, The Netherlands, United Kingdom, Switzerland,Norway, Iceland 0682
UniStoneImportant Application InformationProduct Specification 211 T3130-8XV10T4-7600, 2006-12-18CONFIDENTIAL
UniStoneImportant Application InformationProduct Specification 212 T3130-8XV10T4-7600, 2006-12-18CONFIDENTIAL9.7 Industry Canada CertificationPBA31308 comply with the regulatory requirements of Industry canada (IC), license:IC: 6850A-31308Manufacturers of mobile, fixed or portable devices incorporating this module are advisedto clarify any regulatory questions and ensure compliance for SAR and/or RF exposurelimits. Users can obtain Canadian information on RF exposure and compliance fromwww.ic.gc.caThis device has been designed to operate with the antenna listed in section 8.1 above ,having a maximum gain of 4.0 to 4.5 dBi. Antennas not included in this list or having again greater than 4.0 dB are strictly prohibited for use with this device. The requiredantenna impedance is 50 ohms. The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.9.8 Label design of the host productIt is recommended to include the following information on the host product label:Contains transmitter Module FCC ID: Q2331308 / IC: 6850A-31308

Navigation menu