Intel DG45ID Intel® Desktop Board DG45IDProduct Guide User Manual To The F39bbd1b 505f 42eb B66f 4981764f8e46

User Manual: Intel DG45ID to the manual

Open the PDF directly: View PDF .
Page Count: 86

Download
Open PDF In Browser	View PDF

Intel® Desktop Board DG45ID
Product Guide
Order Number: E30021-001

Revision History
Revision
-001

Revision History
First release of the Intel® Desktop Board DG45ID Product Guide

Date
May 2008

If an FCC declaration of conformity marking is present on the board, the following statement applies:

FCC Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
For questions related to the EMC performance of this product, contact:
Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124
1-800-628-8686
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and the receiver.
•
Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the
user’s authority to operate the equipment.
Tested to comply with FCC standards for home or office use.

Canadian Department of Communications Compliance Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set
out in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numerique német pas de bruits radioélectriques dépassant les limites applicables aux
appareils numériques de la classe B prescrites dans le Réglement sur le broullage radioélectrique édicté par
le ministére des Communications du Canada.

Disclaimer
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. NO LICENSE,
EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS
GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL’S TERMS AND CONDITIONS OF SALE FOR
SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR
IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR
WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT
OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Intel products are not intended
for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and
product descriptions at any time, without notice.
Desktop Board DG45ID may contain design defects or errors known as errata which may cause the product
to deviate from published specifications. Current characterized errata are available on request.
Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing
your product order.
Copies of documents which have an ordering number and are referenced in this document, or other Intel
literature, may be obtained from Intel Corporation by going to the World Wide Web site at:
http://intel.com/ or by calling 1-800-548-4725.
Intel, the Intel logo, and Intel Viiv are trademarks of Intel Corporation in the U.S. and other countries.
* Other names and brands may be claimed as the property of others.
Copyright © 2008, Intel Corporation. All rights reserved.

Preface
This Product Guide gives information about board layout, component installation, BIOS
update, and regulatory requirements for Intel® Desktop Board DG45ID.

Intended Audience
The Product Guide is intended for technically qualified personnel. It is not intended for
general audiences.

Use Only for Intended Applications
All Intel Desktop Boards are evaluated as Information Technology Equipment (I.T.E.)
for use in personal computers (PC) for installation in homes, offices, schools, computer
rooms, and similar locations. The suitability of this product for other PC or embedded
non-PC applications or other environments, such as medical, industrial, alarm systems,
test equipment, etc. may not be supported without further evaluation by Intel.

Document Organization
The chapters in this Product Guide are arranged as follows:
1

Desktop Board Features: a summary of product features

Installing and Replacing Desktop Board Components: instructions on how to install
the Desktop Board and other hardware components

Updating the BIOS: instructions on how to update the BIOS

Configuring for RAID (Intel® Matrix Storage Technology (Intel® MST)): information
about configuring your system for RAID

Configuring for Intel® Rapid Recover Technology (Intel® RRT): information about
configuring your system for Intel Rapid Recover Technology

Error Messages and Indicators: information about BIOS error messages and beep
codes

Regulatory Compliance: safety standards, regulations, and product certifications

Conventions
The following conventions are used in this manual:

CAUTION
Cautions warn the user about how to prevent damage to hardware or loss of data.

iii

Intel Desktop Board DG45ID Product Guide

NOTE
Notes call attention to important information.

Terminology
The table below gives descriptions of some common terms used in the product guide.

Term

Description

Gigabyte (1,073,741,824 bytes)

GHz

Gigahertz (one billion hertz)

Kilobyte (1024 bytes)

Megabyte (1,048,576 bytes)

Mbit

Megabit (1,048,576 bits)

MHz

Megahertz (one million hertz)

Contents
1 Desktop Board Features ................................................................9
Desktop Board Components.................................................................................11
Processor..........................................................................................................13
Main Memory.....................................................................................................13
Intel® G45 Express Chipset .................................................................................14
Intel G45 Graphics Subsystem......................................................................14
DVI-I Support .....................................................................................15
HDMI* Technology Support ..................................................................15
PCI Express x16 Graphics .....................................................................16
Intel® Viiv™ Technology ..............................................................................16
Audio Subsystem ...............................................................................................16
Legacy Input/Output (I/O) Controller ....................................................................17
LAN Subsystem .................................................................................................17
LAN Subsystem Software.............................................................................17
LAN Status Indicators..................................................................................18
Hi-Speed USB 2.0 Support ..................................................................................18
Serial ATA.........................................................................................................19
Serial ATA RAID .........................................................................................19
Intel® Rapid Recover Technology (Intel® RRT) ................................................19
Expandability.....................................................................................................19
BIOS ................................................................................................................20
Serial ATA Auto Configuration.......................................................................20
PCI and PCI Express* Auto Configuration .......................................................20
Security Passwords .....................................................................................20
Hardware Management Features ..........................................................................21
Fan Speed, Thermal, and Voltage Monitoring and Control .................................21
Chassis Intrusion........................................................................................21
Power Management Features ...............................................................................22
ACPI .........................................................................................................22
Hardware Support ......................................................................................22
Power Connectors ...............................................................................22
Fan Headers .......................................................................................23
LAN Wake Capabilities..........................................................................23
Instantly Available PC Technology..........................................................23
+5 V Standby Power Indicator...............................................................24
Wake from USB ..................................................................................25
PME# Signal Wake-up Support..............................................................25
WAKE# Signal Wake-up Support ...........................................................25
Wake from CIR ...................................................................................25
ENERGY STAR* Qualified .............................................................................25
Speaker............................................................................................................25
Battery .............................................................................................................25
Real-Time Clock.................................................................................................25

Intel Desktop Board DG45ID Product Guide

2 Installing and Replacing Desktop Board Components .................27
Before You Begin ...............................................................................................27
Installation Precautions.......................................................................................28
Prevent Power Supply Overload ....................................................................28
Observe Safety and Regulatory Requirements.................................................28
Installing the I/O Shield ......................................................................................29
Installing and Removing the Desktop Board ...........................................................30
Installing and Removing a Processor .....................................................................31
Installing a Processor ..................................................................................31
Installing a Processor Fan Heat Sink ..............................................................34
Connecting the Processor Fan Heat Sink Cable................................................35
Removing the Processor ..............................................................................35
Installing and Removing Memory..........................................................................36
Guidelines for Dual Channel Memory Configuration ..........................................36
Two or Four DIMMs .............................................................................36
Three DIMMs ......................................................................................37
Installing DIMMs ........................................................................................38
Removing DIMMs........................................................................................40
Installing and Removing a PCI Express x16 Card ....................................................41
Installing a PCI Express x16 Card .................................................................41
Removing the PCI Express x16 Card..............................................................42
Connecting Serial ATA (SATA) Cables....................................................................43
Connecting to Internal Headers and Connectors .....................................................44
HD Audio Link Header .................................................................................45
S/PDIF Connector .......................................................................................45
Front Panel HD Audio Header .......................................................................45
Consumer IR (CIR) Headers .........................................................................46
Serial Port Header ......................................................................................47
Chassis Intrusion Header .............................................................................47
Alternate Front Panel Power LED Header ........................................................47
Front Panel Header .....................................................................................48
USB 2.0 Headers ........................................................................................48
IEEE 1394a Header .....................................................................................49
Connecting to the Audio System...........................................................................49
Connecting Chassis Fan and Power Supply Cables...................................................50
Chassis Fan Cables .....................................................................................50
Power Supply Cables...................................................................................51
Setting the BIOS Configuration Jumper .................................................................52
Clearing Passwords ............................................................................................53

3 Updating the BIOS.......................................................................61
Updating the BIOS with the Intel® Express BIOS Update Utility.................................61
Updating the BIOS with the ISO Image BIOS Update File or the Iflash Memory Update
Utility .........................................................................................................62
Obtaining the BIOS Update File ....................................................................62
Updating the BIOS with the ISO Image BIOS Update File .................................62
Updating the BIOS with the Iflash Memory Update Utility .................................63
Recovering the BIOS ...................................................................................64

Contents

4 Configuring for RAID (Intel® Matrix Storage Technology (Intel®
MST)) ..........................................................................................65
Configuring the BIOS for Intel Matrix Storage Technology ................................65
Creating Your RAID Set ...............................................................................65
Loading the Intel Matrix Storage Technology RAID Drivers and Software ............66
Setting Up a “RAID Ready” System ...............................................................66

5 Configuring for Intel® Rapid Recover Technology........................67
Enabling Intel Rapid Recover Technology...............................................................67
Creating a Recovery Volume ................................................................................68
Creating a Recovery Volume Using the RAID Option ROM .................................68
Creating a Recovery Volume Using the Intel Matrix Storage Console ..................68
Disk Synchronization Mode ..................................................................................69
Mounting the Recovery Disk ................................................................................69

A Error Messages and Indicators ....................................................71
BIOS Beep Codes ...............................................................................................71
BIOS Error Messages ..........................................................................................71

B Regulatory Compliance................................................................73
Safety Standards ...............................................................................................73
Place Battery Marking .................................................................................73
European Union Declaration of Conformity Statement..............................................74
Product Ecology Statements ................................................................................75
Recycling Considerations .............................................................................75
Lead-free 2LI/Pb-free 2LI Board ...................................................................78
Restriction of Hazardous Substances (RoHS) ..................................................79
EU RoHS ............................................................................................79
China RoHS ........................................................................................80
EMC Regulations ................................................................................................82
Ensure Electromagnetic Compatibility (EMC) Compliance ..................................83
Product Certifications..........................................................................................84
Board-Level Certification Markings ................................................................84
Chassis and Component Certifications............................................................85

Figures
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.

Desktop Board DG45ID Components ...............................................................11
LAN Status LEDs ..........................................................................................18
Location of the +5 V Standby Power Indicator ..................................................24
Installing the I/O Shield ................................................................................29
Desktop Board DG45ID Mounting Screw Hole Locations .....................................30
Lift the Socket Lever .....................................................................................31
Lift the Load Plate.........................................................................................32
Remove the Protective Socket Cover ...............................................................32
Remove the Processor from the Protective Processor Cover ................................33
Install the Processor .....................................................................................33
Close the Load Plate .....................................................................................34
Connecting the Processor Fan Heat Sink Cable..................................................35
Dual Channel Memory Configuration with Two DIMMs ........................................36
Dual Channel Memory Configuration with Four DIMMs........................................37
Dual Channel Memory Configuration with Three DIMMs ......................................37

vii

Intel Desktop Board DG45ID Product Guide

16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.

Use DDR2 DIMMs .........................................................................................38
Installing a DIMM .........................................................................................39
Installing a PCI Express x16 Card ...................................................................41
Removing a PCI Express x16 Card ..................................................................42
Connecting a Serial ATA Cable........................................................................43
Internal Headers and Connectors ....................................................................44
Back Panel Audio Connectors .........................................................................49
Location of the Chassis Fan Headers................................................................50
Connecting Power Supply Cables ....................................................................51
Location of the BIOS Configuration Jumper Block ..............................................52
Removing the Battery ...................................................................................59
Desktop Board DG45ID China RoHS Material Self Declaration Table .....................81

Tables
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.

viii

Feature Summary.......................................................................................... 9
Desktop Board DG45ID Components ...............................................................12
Audio Jack Retasking Support.........................................................................17
LAN Connector LEDs .....................................................................................18
HD Audio Link Header Signal Names ...............................................................45
S/PDIF Connector Signal Names .....................................................................45
Front Panel Audio Header Signal Names...........................................................45
Front Panel CIR Receiver (Input) Header Signal Names ......................................46
Back Panel CIR Emitter (Output) Header Signal Names ......................................46
Serial Port Header Signal Names.....................................................................47
Chassis Intrusion Header Signal Names ...........................................................47
Alternate Front Panel Power LED Header Signal Names ......................................47
Front Panel Header Signal Names ...................................................................48
USB 2.0 Header Signal Names........................................................................48
IEEE 1394a Header Signal Names ...................................................................49
Jumper Settings for the BIOS Setup Program Modes..........................................53
Beep Codes .................................................................................................71
BIOS Error Messages ....................................................................................71
Safety Standards..........................................................................................73
Lead-Free Second Level Interconnect Marks .....................................................79
China RoHS Environmentally Friendly Use Period Mark .......................................80
EMC Regulations...........................................................................................82
Product Certification Markings ........................................................................84

1 Desktop Board Features
This chapter briefly describes the features of Intel® Desktop Board DG45ID. Table 1
summarizes the major features of the Desktop Board.
Table 1. Feature Summary
Form Factor

microATX (243.84 millimeters [9.60 inches] x 243.84 millimeters
[9.60 inches])

Processor

Support for an Intel® processor in the LGA775 package

Main Memory

• Four 240-pin, DDR2 1.8 V SDRAM Dual Inline Memory Module
(DIMM) sockets
• 800/667 MHz single or dual channel DDR2 SDRAM interface
• Support for up to 8 GB of system memory

Chipset

Intel® G45 Express Chipset consisting of:
• Intel G45 Express Chipset Graphics and Memory Controller Hub
(GMCH)
• Intel® 82801JR I/O Controller Hub (ICH10R)

Graphics

• Intel G45 Express Chipset with Intel® Graphics Media Accelerator
X4500HD (Intel® GMA X4500HD)
• One PCI Express* 2.0 x16 connector supporting PCI Express
graphics add-in cards
• High-Definition Multimedia Interface* (HDMI*) output
• Support for dual independent displays via the HDMI/DVI-I ports

Audio

Onboard subsystem, featuring:
• Independent 8-channel (7.1) audio streams
• 2-channel stereo audio streams via an onboard header
• Intel® High Definition Audio (Intel® HD Audio) interface
• IDT* 92HD73E audio codec
• Back panel optical S/PDIF output connector and an onboard 3-pin
S/PDIF output connector
• Dolby Home Theater* certified audio

Expansion
Capabilities

• One PCI Express 2.0 x16 connector
• Two PCI Express 1.1 x1 connectors
• One PCI* connector

Legacy I/O Support

Legacy I/O Controller that provides:
• Consumer Infrared (CIR) support
• One serial port via an onboard header
continued

Intel Desktop Board DG45ID Product Guide

Table 1. Feature Summary (continued)
Peripheral
Interfaces

• Up to 12 USB 2.0 ports:
― Six ports routed to the back panel
― Six ports routed to three USB headers
• Up to two IEEE 1394a ports:
― One port routed to the back panel
― One port routed to an onboard IEEE 1394a header
• Six Serial ATA (SATA) channels (3.0 Gb/s) via ICH10R including one
external SATA (eSATA) channel
• SATA RAID support via Intel® Matrix Storage Technology (Intel®
MST) including support for Intel® Rapid Recover Technology (Intel®
RRT)

BIOS

•
•
•
•
•

Intel® Platform Innovation Framework for EFI
32 Mbit symmetrical flash memory device
Support for SMBIOS
Intel® Rapid BIOS Boot
Intel® Express BIOS Update

Power Management

•
•
•
•

Support for Advanced Configuration and Power Interface (ACPI)
Suspend to RAM (STR)
Wake on USB, PCI Express, LAN, front panel, and Consumer IR
ENERGY STAR* capable

Hardware
Management

Hardware monitor with:
• Three fan sensing inputs used to monitor fan activity
• Intel® Quiet System Technology (Intel® QST) fan speed control
• Voltage sensing to detect out of range values

LAN Support

Intel® 82567LF Gigabit (10/100/1000 Mb/s) Ethernet LAN controller

Operating System
Support

•
•
•
•
•
•
•
•
•
•
•
•
•
•

Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft

Windows Vista* Ultimate
Windows Vista Enterprise
Windows Vista Business
Windows Vista Home Premium
Windows Vista Home Basic
Windows Vista Ultimate 64-bit edition
Windows Vista Enterprise 64-bit edition
Windows Vista Business 64-bit edition
Windows Vista Home Premium 64-bit edition
Windows Vista Home Basic 64-bit edition
Windows* XP Media Center Edition 2005
Windows XP Professional
Windows XP Professional x64 Edition
Windows XP Home

For more information about Desktop Board DG45ID, including the Technical Product
Specification (TPS), BIOS updates, and device drivers, go to
http://support.intel.com/support/motherboards/desktop/.

Desktop Board Features

Desktop Board Components
Figure 1 shows the approximate location of the major components on Desktop Board
DG45ID.

Figure 1. Desktop Board DG45ID Components

Intel Desktop Board DG45ID Product Guide

Table 2. Desktop Board DG45ID Components
Label

Description

Front panel audio header

PCI bus connector

PCI Express x1 connector 2

PCI Express x16 connector

PCI Express x1 connector 1

Rear chassis fan header (3-pin)

Back panel connectors

Back panel CIR emitter (output)

12 V processor core voltage connector (2 x 2 pin)

Serial header

Processor socket

Processor fan header (4-pin)

Front panel CIR receiver (input)

Main power connector (2 x 12 pin)

DDR2 DIMM 0 sockets

DDR2 DIMM 1 sockets

Front chassis fan header (3-pin)

Battery

Chassis intrusion header

Alternate front panel power LED header

Front panel header

BIOS configuration jumper block

Serial ATA connectors (5)

Speaker

High-speed USB 2.0 headers (3)

IEEE 1394a header

HD audio link header

S/PDIF header

For more information about Intel Desktop Board DG45ID, go to
http://intel.com/design/motherbd.

Desktop Board Features

Processor
CAUTION
Failure to use an appropriate power supply and/or not connecting the 12 V (2 x 2 pin)
power connector to the Desktop Board may result in damage to the board, or the
system may not function properly.
Desktop Board DG45ID supports an Intel processor in the LGA775 package.
Processors are not included with the Desktop Board and must be purchased
separately. The processor connects to the Desktop Board through the LGA775 socket.
Go to the following locations for more information about:
•
•

Instructions on installing or upgrading the processor, page 31 in Chapter 2
Supported processors for Desktop Board DG45ID, http://processormatch.intel.com

Main Memory
NOTE
To be fully compliant with all applicable Intel ® SDRAM memory specifications, the
board should be populated with DIMMs that support the Serial Presence Detect (SPD)
data structure. If your memory modules do not support SPD, you will see a
notification to this effect on the screen at power up. The BIOS will attempt to
configure the memory controller for normal operation.
The Desktop Board supports the dual or single channel memory configurations defined
below.
•
•

•

Four 240-pin Double Data Rate 2 (DDR2) SDRAM Dual Inline Memory Module
(DIMM) connectors with gold-plated contacts
Support for:
⎯ Non-ECC, 1.8 V, DDR2 800/667 MHz memory
⎯ Serial Presence Detect (SPD) memory only
⎯ Unbuffered, non-registered single- or double-sided DIMMs (except double-sided
DIMMs with x16 organization)
⎯ Memory configurations listed below:
• Up to 2.0 GB utilizing 256 Mb technology
• Up to 4.0 GB utilizing 512 Mb or 1 Gb technology
• Up to 8.0 GB utilizing 1 Gb technology
A minimum of 512 MB of total memory is required

Intel Desktop Board DG45ID Product Guide

NOTE
System resources and hardware (such as PCI Express) require physical memory
address locations that can reduce available addressable system memory. This could
result in a reduction of as much as 1 GB or more of physical addressable memory
being available to the operating system and applications, depending on the system
configuration and operating system.
Go to the following locations for more information about:
•
•
•

SDRAM specifications, http://intel.com/technology/memory/
Installing memory, page 36 in Chapter 2
Tested memory, http://cmtlabs.com/mbsearch.asp

Intel® G45 Express Chipset
The Intel G45 Express Chipset consists of the following devices:
•
•

Intel G45 Express Chipset Graphics and Memory Controller Hub (GMCH) with Direct
Media Interface (DMI)
Intel 82801JR I/O Controller Hub (ICH10R) with DMI

The GMCH component provides interfaces to the processor, memory, PCI Express, and
the DMI interconnect. The component also provides integrated graphics capabilities
supporting 3D, 2D, and display capabilities. The ICH10R is a centralized controller for
the board’s I/O paths.
For more information on the Intel G45 Express Chipset go to
http://developer.intel.com/products/chipsets/

Intel G45 Graphics Subsystem
The Intel G45 Express Chipset contains two separate, mutually exclusive graphics
options. Either the integrated Intel Graphics Media Accelerator X4500HD
(GMA X4500HD) graphics controller is used or a PCI Express x16 add-in card can be
used.
The GMA X4500 graphics controller supports dual independent displays via the HDMI
and DVI-I connectors on the Desktop Board back panel. When a PCI Express x16, x8,
or x4 add-in card is installed on the Desktop Board, the Intel GMA X4500 graphics
controller is disabled.

Desktop Board Features

The Intel GMA X4500HD graphics controller has the following features:
•

Advanced graphics performance, including:

•

⎯ DirectX10.0* and OpenGL* 2.0 compliant
⎯ Shader Model 4.0 support
Enhanced video playback support, including:

•

⎯ Intel® Clear Video Technology (for more information go to
http://intel.com/products/chipsets/clear_video/)
⎯ Support for playback of Blu-ray Disc* technology DVDs
⎯ Software DVD at 30 fps full screen
⎯ Dynamic Video Memory Technology (DVMT) 5.0
Advanced display support, including:
⎯ DVI specification 1.0 compliant
⎯ Dual independent display support via the DVI-I and HDMI back panel
connectors
⎯ High Definition Content Protection (HDCP) version 1.1 support
⎯ DDC2B compliant interface with Advanced Digital Display 2 card or Media
Expansion Card (ADD2/MEC), support for TV-out/TV-in and DVI digital display
connections
⎯ Support for all HD display resolutions including 720p, 1080i, and 1080p
⎯ Support for digital and analog displays up to 2048 x 1536 at 75 Hz refresh rate
(QXGA); also supports 1920 x 1080 resolution for full High Definition video
playback quality

DVI-I Support
The DVI-I port supports both digital and analog DVI displays. The maximum
supported resolution is 2048 x 1536 at 75 Hz refresh rate (QXGA). DVI analog output
can be converted to VGA with a DVI-to-VGA connector.
When a PCI Express x16, x8, or x4 add-in card is installed on the Desktop Board, the
DVI-I port is disabled.

HDMI* Technology Support
The HDMI port supports standard, enhanced, or high-definition video, plus multichannel digital audio on a single cable. It is compatible with all ATSC and DVB HDTV
standards and supports 8-channel digital audio. The HDMI port is compliant with the
HDMI 1.3 specification.
When a PCI Express x16, x8, or x4 add-in card is installed on the Desktop Board, the
HDMI port is disabled.

Intel Desktop Board DG45ID Product Guide

PCI Express x16 Graphics
The GMCH also supports an add-in PCI Express discrete graphics card via the PCI
Express 2.0 x16 connector as follows:
•

•

Supports PCI Express 1.1 frequency of 1.25 GHz resulting in 2.5 Gb/s each
direction (500 MB/s total). The maximum theoretical bandwidth on the interface is
4 GB/s in each direction simultaneously, for an aggregate of 8 GB/s when
operating in x16 mode.
Supports PCI Express 2.0 frequency of 2.5 GHz resulting in 5.0 Gb/s each direction
(1000 MB/s total). The maximum theoretical bandwidth on the interface is 8 GB/s
in each direction simultaneously, for an aggregate of 16 GB/s when operating in
x16 mode.

For more information on PCI Express technology, go to http://pcisig.com.

Intel® Viiv™ Technology
The Desktop Board supports Intel® Viiv™ technology. To be eligible for the Intel Viiv
technology brand, a system must meet certain hardware and software requirements.
To get the list of requirements for Intel Viiv technology branding as well as all the
features supported by Intel Viiv technology, visit
http://intel.com/products/viiv/index.htm.

Audio Subsystem
The onboard audio subsystem consists of the following:
•
•
•
•
•
•

Intel ICH10R I/O controller hub
IDT 92HD73E audio codec
Intel High Definition Audio front panel audio header
Intel High Definition Audio Link header
Onboard 3-pin S/PDIF output connector
Back panel audio connectors including an optical S/PDIF output connector

The audio subsystem supports the following features:
•
•
•

A signal-to-noise (S/N) ratio of 95 dB
Independent multi-streaming 7.1 audio (using the back panel audio connectors)
and stereo (using the Intel High Definition front panel audio header)
Dolby Home Theater certified audio

Go to the following locations for more information about:
•
•
•

Audio drivers and utilities http://support.intel.com/support/motherboards/desktop/
Location of the onboard audio headers, Figure 21 on page 44
The location and description of the back panel audio connectors, Figure 22 on
page 49

Table 3 lists the supported functions for the front panel and back panel audio jacks.

Desktop Board Features

Table 3. Audio Jack Retasking Support
Jack

Mic

Line out

Head-phones

Green

Yes

Pink

Yes

Blue

Green

Yes

Line in/Side
Surround

Rear
Surround

Center/
Subwoofer

Yes

Front Panel

Back Panel

Pink

Yes

Black

Yes

Orange

Yes

Legacy Input/Output (I/O) Controller
The I/O controller features the following:
•
•
•
•
•
•

Low pin count (LPC) interface
One serial port interface via an onboard header
Consumer Infrared (CIR) support
Serial IRQ interface compatible with serialized IRQ support for PCI systems
Intelligent power management, including a programmable wake up event interface
PCI power management support

LAN Subsystem
The LAN subsystem includes:
•
•
•

Intel® ICH10R
Intel 82567LF Gigabit (10/100/1000 Mb/s) Ethernet LAN controller
RJ-45 LAN connector with integrated status LEDs

The subsystem features:
• CSMA/CD protocol engine
• LAN connect interface between ICH10R and the LAN controller
• PCI Express power management
For information about LAN software and drivers go to
http://support.intel.com/support/motherboards/desktop

LAN Subsystem Software
For LAN software and drivers, refer to the DG45ID link on Intel’s World Wide Web site
at http://support.intel.com/support/motherboards/desktop.

Intel Desktop Board DG45ID Product Guide

LAN Status Indicators
Two LEDs are built into the RJ-45 LAN connector located on the back panel (see
Figure 2). These LEDs indicate the operating states of the LAN.

Figure 2. LAN Status LEDs
Table 4 describes the LED states when the board is powered up and the LAN
subsystem is operating.
Table 4. LAN Connector LEDs
LED

LED Color

A (Link)

Green

B (Speed)

LED State

Indicates

Off

LAN link is not established

LAN link is established

Blinking

LAN activity is occurring

N/A

Off

10 Mb/s data rate

Green

100 Mb/s data rate

Yellow

1000 Mb/s data rate

Hi-Speed USB 2.0 Support
The Desktop Board supports up to 12 USB 2.0 ports (six ports routed to the back
panel and six ports routed to three internal headers) via ICH10R. USB 2.0 ports are
backward compatible with USB 1.1 devices. USB 1.1 devices will function normally at
USB 1.1 speeds.
USB 2.0 support requires both an operating system and drivers that fully support
USB 2.0 transfer rates. Disabling Hi-Speed USB in the BIOS reverts all USB 2.0 ports
to USB 1.1 operation. This may be required to accommodate operating systems that
do not support USB 2.0.

Desktop Board Features

Serial ATA
The Desktop Board supports six Serial ATA channels (3.0 Gb/s) via ICH10R,
connecting one device per channel. One channel is configured as an eSATA channel.

Serial ATA RAID
ICH10R supports Intel® Matrix Storage Technology which enables the following RAID
(Redundant Array of Independent Drives) levels:
•
•
•
•

RAID
RAID
RAID
RAID

0 - data striping
1 - data mirroring
0+1 (or RAID 10) - data striping and mirroring
5 - distributed parity

For information on configuring your system for RAID using Intel Matrix Storage
Technology see Chapter 4.

Intel® Rapid Recover Technology (Intel® RRT)
The Desktop Board supports Intel Rapid Recover Technology which enables fast and
easy recovery of your data in the event of a hard drive failure. It allows you to
maintain a complete copy of your primary or master drive onto a second hard drive,
the recovery drive. If the master hard drive should fail, either from a mechanical
failure or the result of a virus, recovery is as simple as booting from the recovery
drive. The recovery drive can be attached to your system via any standard SATA or
eSATA connection.
Intel Rapid Recover Technology also provides the added benefit of allowing the
recovery drive to be mounted as a read-only volume so you can quickly copy files from
the recovery drive when individual files need to be recovered.
For information on configuring your system for Intel Rapid Recover Technology see
Chapter 5.

Expandability
For system expansion, the Desktop Board provides the following expansion slots:
•
•
•

One PCI Express 2.0 x16 connector (compatible with PCI Express 1.1 add-in cards)
Two PCI Express 1.1 x1 connectors
One PCI bus connector

Intel Desktop Board DG45ID Product Guide

BIOS
The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, the
PCI/PCI Express auto-configuration utilities, and the video BIOS. The BIOS is stored in
the Serial Peripheral Interface (SPI) Flash device.
The BIOS can be updated by following the instructions in Chapter 3.

Serial ATA Auto Configuration
If you install a Serial ATA device (such as a hard drive) in your computer, the autoconfiguration utility in the BIOS automatically detects and configures the device for
your computer. You do not need to run the BIOS Setup program after installing a
Serial ATA device. You can override the auto-configuration options by specifying
manual configuration in the BIOS Setup program.

PCI and PCI Express* Auto Configuration
If you install a PCI/PCI Express add-in card in your computer, the PCI/PCI Express
auto-configuration utility in the BIOS automatically detects and configures the
resources (IRQs, DMA channels, and I/O space) for that add-in card. You do not need
to run the BIOS Setup program after you install a PCI/PCI Express add-in card.

Security Passwords
The BIOS includes security features that restrict whether the BIOS Setup program can
be accessed and who can boot the computer. A supervisor password and a user
password can be set for the BIOS Setup and for booting the computer, with the
following restrictions:
•

•

The supervisor password gives unrestricted access to view and change all Setup
options. If only the supervisor password is set, pressing at the password
prompt of Setup gives the user restricted access to Setup.
If both the supervisor and user passwords are set, you must enter either the
supervisor password or the user password to access Setup. Setup options are then
available for viewing and changing depending on whether the supervisor or user
password was entered.
Setting a user password restricts who can boot the computer. The password
prompt is displayed before the computer is booted. If only the supervisor
password is set, the computer boots without asking for a password. If both
passwords are set, you can enter either password to boot the computer.

For instructions on resetting the password, see Clearing Passwords on page 53.

Desktop Board Features

Hardware Management Features
The hardware management features of Desktop Board DG45ID enable the board to be
compatible with the Wired for Management (WfM) specification. The board has several
hardware management features including the following:
•
•
•

Fan speed monitoring and control
Thermal and voltage monitoring
Chassis intrusion detection

Fan Speed, Thermal, and Voltage Monitoring and
Control
The board’s fan speed, thermal, and voltage monitoring and control features include
the following:
•
•

Monitoring of power supply voltages to detect levels above and below acceptable
values
Intel Quiet System Technology fan speed control, delivering acoustically-optimized
thermal management

NOTE
Memory must be installed in the Channel A, DIMM 0 socket to enable Intel
Quiet System Technology.
•

Thermally monitored closed-loop fan control, for all onboard fans, that can adjust
fan speed according to thermal conditions.
• Fan speed controllers and sensors integrated into the ICH10R
• Thermal sensors in the processor, GMCH, and ICH10R, plus an onboard remote
sensor

NOTE
The minimum thermal reporting threshold for the GMCH is 66 °C. The GMCH thermal
sensor will display 66 °C until the temperature rises above this point.

Chassis Intrusion
The board supports a chassis security feature that detects if the chassis cover has
been removed. The security feature uses a mechanical switch on the chassis that can
be connected to the chassis intrusion header on the Desktop Board. See Figure 21 for
the location of the chassis intrusion header.

Intel Desktop Board DG45ID Product Guide

Power Management Features
Power management is implemented at several levels, including:
•
•

•

Software support through the Advanced Configuration and Power Interface (ACPI)
Hardware support:
⎯ Power connectors
⎯ Fan headers
⎯ LAN wake capabilities
⎯ Instantly Available PC technology (Suspend to RAM)
⎯ +5 V standby power indicator LED
⎯ Wake from USB
⎯ Power Management Event signal (PME#) wakeup support
⎯ WAKE# signal wake-up support
⎯ Wake from Consumer IR
ENERGY STAR qualified

ACPI
ACPI gives the operating system direct control over the power management and Plug
and Play functions of a computer. The use of ACPI with the Desktop Board requires an
operating system that provides full ACPI support.

Hardware Support
Power Connectors
ATX12V-compliant power supplies can turn off the computer power through system
control. When an ACPI-enabled computer receives the correct command, the power
supply removes all non-standby voltages.
When resuming from an AC power failure, the computer returns to the power state it
was in before power was interrupted (either on or off). The computer’s response can
be set by using the Last Power State feature in the BIOS Setup program’s Boot menu.
The Desktop Board has two power connectors. See Figure 24 on page 51 for the
location of the power connectors.

Desktop Board Features

Fan Headers
The function/operation of the fans is as follows:
•
•
•
•

The fans are on when the computer is in the ACPI S0 state.
The fans are off when the computer is in the ACPI S3, S4, or S5 state.
All fan headers support closed-loop fan control that can adjust the fan speed
according to thermal conditions.
All fan headers have a +12 V DC connection.

The Desktop Board has a 4-pin processor fan header and two 3-pin chassis fan
headers.

LAN Wake Capabilities
CAUTION
For LAN wake capabilities, the 5 V standby line for the power supply must be capable
of delivering adequate +5 V standby current. Failure to provide adequate standby
current when using this feature can damage the power supply.
LAN wakeup capabilities enable remote wake-up of the computer through a network.
The LAN subsystem monitors network traffic and upon detecting a Magic Packet*
frame, it asserts a wake-up signal that powers up the computer.

Instantly Available PC Technology
CAUTIONS
For Instantly Available PC technology, the 5 V standby line for the power supply must
be capable of delivering adequate +5 V standby current. Failure to provide adequate
standby current when using this feature can damage the power supply and/or effect
ACPI S3 sleep state functionality.
Power supplies used with this Desktop Board must be able to provide enough standby
current to support the standard Instantly Available (ACPI S3 sleep state) configuration.
If the standby current necessary to support multiple wake events from the PCI and/or
USB buses exceeds power supply capacity, the Desktop Board may lose register
settings stored in memory.
Instantly Available PC technology enables the board to enter the ACPI S3 (Suspend-toRAM) sleep state. While in the S3 sleep state, the computer will appear to be off. If
the computer has a dual-colored power LED on the front panel, the sleep state is
indicated by the LED turning amber. When signaled by a wake-up device or event, the
computer quickly returns to its last known awake state.
The Desktop Board supports the PCI Bus Power Management Interface Specification.
Add-in cards that support this specification can participate in power management and
can be used to wake the computer.

Intel Desktop Board DG45ID Product Guide

+5 V Standby Power Indicator
CAUTION
If the AC power has been switched off and the standby power indicator is still lit,
disconnect the power cord before installing or removing any devices connected to the
board. Failure to do so could damage the board and any attached devices.
The Desktop Board’s standby power indicator, shown in Figure 3, is lit when there is
standby power still present on the board even when the computer appears to be off.
For example, when this green LED is lit, standby power is still present at the memory
module sockets and the PCI/PCI Express bus connectors.

Figure 3. Location of the +5 V Standby Power Indicator
For more information on standby current requirements for the Desktop Board, refer to
the Technical Product Specification by going to
http://support.intel.com/support/motherboards/desktop/, finding the product, and
clicking on the Technical Documents tab.

Desktop Board Features

Wake from USB
NOTE
Wake from USB requires the use of a USB peripheral that supports Wake from USB.
USB bus activity wakes the computer from an ACPI S3 state.

PME# Signal Wake-up Support
When the PME# signal on the PCI bus is asserted, the computer wakes from an
ACPI S3, S4, or S5 state.

WAKE# Signal Wake-up Support
When the WAKE# signal on the PCI Express bus is asserted, the computer wakes from
an ACPI S1, S3, S4, or S5 state.

Wake from CIR
Consumer IR device activity wakes the computer from an ACPI S1 or S3 state.

ENERGY STAR* Qualified
In 2007, the US Department of Energy and the US Environmental Protection Agency
revised the ENERGY STAR requirements. Intel worked directly with these two
governmental agencies to define the new requirements. This Desktop Board meets
the ENERGY STAR Category B requirements.
For information about the ENERGY STAR specifications, see:
http://intel.com/cd/channel/reseller/asmo-na/eng/337748.htm.

Speaker
A speaker is mounted on the Desktop Board. The speaker provides audible error code
(beep code) information during the Power-On Self-Test (POST).

Battery
A battery on the Desktop Board keeps the values in CMOS RAM and the clock current
when the computer is turned off. Go to page 54 for instructions on how to replace the
battery.

Real-Time Clock
The Desktop Board has a time-of-day clock and 100-year calendar. The battery on the
Desktop Board keeps the clock current when the computer is turned off.

Intel Desktop Board DG45ID Product Guide

2 Installing and Replacing Desktop
Board Components
This chapter tells you how to:
•
•
•
•
•
•
•
•
•
•
•
•

Install the I/O shield
Install and remove the Desktop Board
Install and remove a processor
Install and remove memory
Install and remove a PCI Express x16 card
Connect the Serial ATA cables
Connect to the internal headers
Connect to the onboard audio system
Connect chassis fan and power supply cables
Set the BIOS configuration jumper
Clear passwords
Replace the battery

Before You Begin
CAUTIONS
The procedures in this chapter assume familiarity with the general terminology
associated with personal computers and with the safety practices and regulatory
compliance required for using and modifying electronic equipment.
Disconnect the computer from its power source and from any telecommunications
links, networks, or modems before performing any of the procedures described in this
chapter. Failure to disconnect power, telecommunications links, networks, or modems
before you open the computer or perform any procedures can result in personal injury
or equipment damage. Some circuitry on the board can continue to operate even
though the front panel power button is off.
Follow these guidelines before you begin:
•
•
•

Always follow the steps in each procedure in the correct order.
Set up a log to record information about your computer, such as model, serial
numbers, installed options, and configuration information.
Electrostatic discharge (ESD) can damage components. Perform the procedures
described in this chapter only at an ESD workstation using an antistatic wrist strap
and a conductive foam pad. If such a station is not available, you can provide
some ESD protection by wearing an antistatic wrist strap and attaching it to a
metal part of the computer chassis.

Intel Desktop Board DG45ID Product Guide

Installation Precautions
When you install and test the Intel Desktop Board, observe all warnings and cautions
in the installation instructions.
To avoid injury, be careful of:
•
•
•
•
•

Sharp pins on connectors
Sharp pins on printed circuit assemblies
Rough edges and sharp corners on the chassis
Hot components (such as processors, voltage regulators, and heat sinks)
Damage to wires that could cause a short circuit

Observe all warnings and cautions that instruct you to refer computer servicing to
qualified technical personnel.

Prevent Power Supply Overload
Do not overload the power supply output. To avoid overloading the power supply,
make sure that the calculated total current loads of all the modules within the
computer is less than the output current rating of each of the power supplies output
circuits.

Observe Safety and Regulatory Requirements
Read and adhere the instructions in this section and the instructions supplied with the
chassis and associated modules. If you do not follow these instructions and the
instructions provided by the chassis and module suppliers, you increase safety risk and
the possibility of noncompliance with regional laws and regulations. If the instructions
for the chassis are inconsistent with these instructions or the instructions for
associated modules, contact the supplier’s technical support to find out how you can
ensure that your computer meets safety and regulatory requirements.
For information about regulatory compliance, go to Appendix B on page 73.

Installing and Replacing Desktop Board Components

Installing the I/O Shield
The Desktop Board comes with an I/O shield. When installed in the chassis, the shield
blocks radio frequency transmissions, protects internal components from dust and
foreign objects, and promotes correct airflow within the chassis.
Install the I/O shield before installing the Desktop Board in the chassis. Place the
shield inside the chassis as shown in Figure 4. Press the shield into place so that it fits
tightly and securely. If the shield does not fit, obtain a properly sized shield from the
chassis supplier.

Figure 4. Installing the I/O Shield

Intel Desktop Board DG45ID Product Guide

Installing and Removing the Desktop Board
CAUTION
Only qualified technical personnel should do this procedure. Disconnect the computer
from its power source before performing the procedures described here. Failure to
disconnect the power before you open the computer can result in personal injury or
equipment damage.
Refer to your chassis manual for instructions on installing and removing the Desktop
Board.
Figure 5 shows the location of the mounting screw holes for Desktop Board DG45ID.

Figure 5. Desktop Board DG45ID Mounting Screw Hole Locations

Installing and Replacing Desktop Board Components

Installing and Removing a Processor
This section contains information on how to install and remove a processor on the
Desktop Board.

Installing a Processor
CAUTION
Before installing or removing the processor, make sure the AC power has been
removed by unplugging the power cord from the computer; the standby power LED
should not be lit (see Figure 3 on page 24). Failure to do so could damage the
processor and the board.
To install a processor, follow these instructions:
1. Observe the precautions in "Before You Begin" on page 27.
2. Open the socket lever by pushing the lever down and away from the socket
(Figure 6, A and B).

Figure 6. Lift the Socket Lever

Intel Desktop Board DG45ID Product Guide

3. Lift the load plate (Figure 7, A). Do not touch the socket contacts (Figure 7, B).

Figure 7. Lift the Load Plate
4. Remove the plastic protective socket cover from the load plate (Figure 8). Do not
discard the protective socket cover. Always replace the socket cover if the
processor is removed from the socket.

Figure 8. Remove the Protective Socket Cover

Installing and Replacing Desktop Board Components

5. Remove the processor from the protective processor cover. Hold the processor
only at the edges, being careful not to touch the bottom of the processor (see
Figure 9). Do not discard the protective processor cover. Always replace the
processor cover if the processor is removed from the socket.

Figure 9. Remove the Processor from the Protective Processor Cover
6. Hold the processor with your thumb and index fingers oriented as shown in
Figure 10. Make sure your fingers align to the socket cutouts (Figure 10, A). Align
notches (Figure 10, B) with the socket (Figure 10, C). Lower the processor straight
down without tilting or sliding it in the socket.

Figure 10. Install the Processor

Intel Desktop Board DG45ID Product Guide

7. Pressing down on the load plate (Figure 11, A), close and engage the socket lever
(Figure 11, B).

Figure 11. Close the Load Plate

Installing a Processor Fan Heat Sink
Desktop Board DG45ID has mounting holes for a processor fan heat sink. For
instructions on how to attach the processor fan heat sink to the Desktop Board, refer
to the boxed processor manual.

Installing and Replacing Desktop Board Components

Connecting the Processor Fan Heat Sink Cable
Connect the processor fan heat sink cable to the 4-pin processor fan header (see
Figure 12). A fan with a 4-pin connector as shown in Figure 12, A is recommended;
however, a fan with a 3-pin connector (Figure 12, B) can be used. However, since a
fan with a 3-pin connector cannot use the onboard fan control, the fan will always
operate at full speed.

Figure 12. Connecting the Processor Fan Heat Sink Cable

Removing the Processor
For instructions on how to remove the processor fan heat sink and processor, refer to
the processor installation manual.

Intel Desktop Board DG45ID Product Guide

Installing and Removing Memory
Desktop board DG45ID has four 240-pin DDR2 DIMM sockets arranged as DIMM 0 and
DIMM 1 in both Channel A and Channel B.

NOTE
Regardless of the memory configuration used (dual or single channel), Channel A,
DIMM 0 must always be populated. This is a requirement of the ICH10R Manageability
Engine feature.

Guidelines for Dual Channel Memory Configuration
Before installing DIMMs, read and follow these guidelines for dual channel
configuration.

Two or Four DIMMs
Install a matched pair of DIMMs equal in speed and size (see Figure 13) in DIMM 0
(blue) of channels A and B.

Figure 13. Dual Channel Memory Configuration with Two DIMMs

Installing and Replacing Desktop Board Components

If additional memory is to be used, install another matched pair of DIMMs in DIMM 1
(black) in channels A and B (see Figure 14).

Figure 14. Dual Channel Memory Configuration with Four DIMMs

Three DIMMs
If you want to use three DIMMs in a dual-channel configuration, install a matched pair
of DIMMs equal in speed and size in DIMM 0 (blue) and DIMM 1 (black) of channel A.
Install a DIMM equal in speed and total size of the DIMMs installed in channel A in
either DIMM 0 or DIMM 1 of channel B (see Figure 15).

Figure 15. Dual Channel Memory Configuration with Three DIMMs

NOTE
All other memory configurations will result in single channel memory operation.

Intel Desktop Board DG45ID Product Guide

Installing DIMMs
To make sure you have the correct DIMM, place it on the illustration of the DDR2
DIMM in Figure 16. All the notches should match with the DDR2 DIMM.

Figure 16. Use DDR2 DIMMs

Installing and Replacing Desktop Board Components

To install a DIMM, follow these steps:
1. Observe the precautions in "Before You Begin" on page 27.
2. Turn off all peripheral devices connected to the computer. Turn off the computer
and disconnect the AC power cord.
3. Remove the computer’s cover and locate the DIMM sockets (see Figure 17).

Figure 17. Installing a DIMM
4. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the
open position.
5. Holding the DIMM by the edges, remove it from its anti-static package.
6. Position the DIMM above the socket. Align the small notch at the bottom edge of
the DIMM with the keys in the socket (see inset in Figure 17).

Intel Desktop Board DG45ID Product Guide

7. Insert the bottom edge of the DIMM into the socket.
8. When the DIMM is inserted, push down on the top edge of the DIMM until the
retaining clips snap into place. Make sure the clips are firmly in place.
9. Replace the computer’s cover and reconnect the AC power cord.

Removing DIMMs
To remove a DIMM, follow these steps:
1.
2.
3.
4.
5.

Observe the precautions in "Before You Begin" on page 27.
Turn off all peripheral devices connected to the computer. Turn off the computer.
Remove the AC power cord from the computer.
Remove the computer’s cover.
Gently spread the retaining clips at each end of the DIMM socket. The DIMM pops
out of the socket.
6. Hold the DIMM by the edges, lift it away from the socket, and store it in an
anti-static package.
7. Reinstall and reconnect any parts you removed or disconnected to reach the DIMM
sockets.
8. Replace the computer’s cover and reconnect the AC power cord.

Installing and Replacing Desktop Board Components

Installing and Removing a PCI Express x16
Card
CAUTION
When installing a PCI Express x16 card on the Desktop Board, ensure that the card is
fully seated in the PCI Express x16 connector before you power on the system. If the
card is not fully seated in the PCI Express connector, an electrical short may result
across the PCI Express connector pins. Depending on the over-current protection of
the power supply, certain Desktop Board components and/or traces may be damaged.

Installing a PCI Express x16 Card
1. Observe the precautions in "Before You Begin" on page 27.
2. Place the card in the PCI Express x16 connector (Figure 18, A) and press down on
the card until it is completely seated in the connector and the card retention notch
on the card snaps into place around the retention mechanism pin on the connector.
3. Secure the card’s metal bracket to the chassis back panel with a screw
(Figure 18, B).

Figure 18. Installing a PCI Express x16 Card

Intel Desktop Board DG45ID Product Guide

Removing the PCI Express x16 Card
Follow these instructions to remove the PCI Express x16 card from the connector:
1. Observe the precautions in "Before You Begin" on page 27.
2. Remove the screw (Figure 19, A) that secures the card’s metal bracket to the
chassis back panel.
3. Push the card ejector lever down using the tip of a pencil or similar tool
(Figure 19, B) in the notch. This will release the card from the connector (C).
4. Pull the card straight up.

Figure 19. Removing a PCI Express x16 Card

Installing and Replacing Desktop Board Components

Connecting Serial ATA (SATA) Cables
SATA cables support the Serial ATA protocol. Each cable can be used to connect a
single SATA drive to the Desktop Board. For correct cable function:
1. Observe the precautions in "Before You Begin" on page 27.
2. Attach one end the SATA cable to one of the SATA connectors on the board
(Figure 20, A).
3. Attach the other end of the SATA cable to the SATA drive (Figure 20, B).

Figure 20. Connecting a Serial ATA Cable

Intel Desktop Board DG45ID Product Guide

Connecting to Internal Headers and
Connectors
Before connecting cables to the internal headers and connectors, observe the
precautions in “Before You Begin” on page 27. Figure 21 shows the location of the
internal headers and connectors.

Item
A
B
C
D
E
F

Description
HD Audio Link
S/PDIF
Audio
Back panel CIR emitter
Serial
Chassis intrusion

Item
G
H
I
J
K

Description
Front panel CIR receiver
Alternate front panel power LED
Front panel
USB 2.0 (3)
IEEE 1394a

Figure 21. Internal Headers and Connectors

Installing and Replacing Desktop Board Components

HD Audio Link Header
See Figure 21, A for the location of the HD Audio Link header. Table 5 shows the pin
assignments for the header.
Table 5. HD Audio Link Header Signal Names
Pin

Signal Name

BCLK

Ground

RST#

DVDD_IO

SYNC

Ground

SDO

3.3V_DVDD_CORE

SDI0

+12 V

SDI1

Key

No Connection

3.3V_DUAL

No Connection

Ground

S/PDIF Connector
Figure 21, B shows the location of the S/PDIF connector. Table 6 shows the pin
assignments and signal names for the S/PDIF connector.
Table 6. S/PDIF Connector Signal Names
Pin

Description

Vcc

S/PDIF Out

Ground

Front Panel HD Audio Header
Figure 21, C shows the location of the front panel audio header. Table 7 shows the pin
assignments for the front panel audio header.
Table 7. Front Panel Audio Header Signal Names
Pin

Signal Name

PORT 1L

GND

PORT 1R

PRESENCE#

PORT 2R

SENSE1_RETURN

SENSE_SEND

KEY (no pin)

PORT 2L

SENSE2_RETURN

Intel Desktop Board DG45ID Product Guide

To install the cable that connects your front panel audio solution to the front panel
audio header, follow these steps:
1. Observe the precautions in "Before You Begin" on page 27.
2. Turn off all peripheral devices connected to the computer. Turn off the computer
and disconnect the AC power cord.
3. Remove the cover.
4. Install a correctly keyed and shielded front panel audio cable.

Consumer IR (CIR) Headers
The Desktop Board has two CIR headers: the receiver or input header (Figure 21, G)
and the output or emitter header (Figure 21, D). The receiver header consists of a
filtered translated infrared input compliant with Microsoft CIR specifications and a
“learning” infrared input. The learning input is a high-pass input which the computer
can use to “learn” to speak the infrared communication language of other user
remotes. The emitter header consists of two output ports which the computer can use
to emulate “learned” infrared commands in order to control external electronic
hardware.

NOTE
The Consumer IR option must be enabled in the system BIOS before it can
function. Press at boot to enter the system BIOS, and go to Advanced >
Peripheral Configuration > Enhanced Consumer IR, and set this option to
Enabled.
Table 8 shows the pin assignments for the front panel CIR receiver (input) header and
Table 9 shows the pin assignments for the back panel CIR emitter (output) header.
Table 8. Front Panel CIR Receiver (Input) Header Signal Names
Pin

Signal Name

Ground

LED

No Connection

Learn-In

+5 V Standby

Vcc

Key (no pin)

CIR Input

Table 9. Back Panel CIR Emitter (Output) Header Signal Names

Signal Name

Emitter Out 1

Emitter Out 2

Ground

Key (no pin)

Jack Detect 1

Jack Detect 2

Installing and Replacing Desktop Board Components

Serial Port Header
See Figure 21, E for the location of the serial port header. Table 10 shows the pin
assignments for the header.
Table 10. Serial Port Header Signal Names
Pin

Signal Name

DCD

RXD#

TXD#

DTR

Ground

DSR

RTS

CTS

No Connection

Chassis Intrusion Header
Figure 21, F on page 44 shows the location of the chassis intrusion header. This
header can be connected to a mechanical switch on the chassis to detect if the chassis
cover is removed. Table 11 shows the pin assignments for the chassis intrusion
header.
Table 11. Chassis Intrusion Header Signal Names
Pin

Description

Intruder

Ground

Alternate Front Panel Power LED Header
Figure 21, H shows the location of the alternate front panel power LED header. Pins 1
and 3 of this header duplicate the signals on pins 2 and 4 of the front panel header. If
your chassis has a three-pin power LED cable, connect it to this header. Table 12
shows the pin assignments for the alternate front panel header.
Table 12. Alternate Front Panel Power LED Header Signal Names
Pin

Description

In/Out

Front panel green LED

Out

No pin

Front panel yellow LED

Out

Intel Desktop Board DG45ID Product Guide

Front Panel Header
See Figure 21, I for the location of the multi-colored front panel header. Table 13
shows the pin assignments for the front panel header.
Table 13. Front Panel Header Signal Names
Pin

Description

In/Out

Description

Hard Drive Activity LED

In/Out

Power LED

Hard disk LED pull-up to +5 V Out

Front panel green LED

Out

Hard disk active LED

Front panel yellow LED

Out

Ground

Power switch

Reset switch

Ground

Power

Out

No pin

Out

Reset Switch

On/Off Switch

Power

Not Connected

USB 2.0 Headers
See Figure 21, J for the location of the three USB 2.0 headers. Table 14 shows the pin
assignments for each USB 2.0 header. Each USB header can be used to connect two
USB devices.
Table 14. USB 2.0 Header Signal Names
USB Port A
Pin
1
3
5
7
9

Signal Name
Power (+5 V)
DD+
Ground
Key

USB Port B
Pin
2
4
6
8
10

Signal Name
Power (+5 V)
DD+
Ground
No Connection

Note: USB ports may be assigned as needed.

NOTE
Computer systems that have an unshielded cable attached to a USB port might not
meet FCC Class B requirements, even if no device or a low-speed USB device is
attached to the cable. Use a shielded cable that meets the requirements for a
full-speed USB device.

Installing and Replacing Desktop Board Components

IEEE 1394a Header
See Figure 21, K for the location of the IEEE 1394a header. Table 15 shows the pin
assignments for the header.
Table 15. IEEE 1394a Header Signal Names
Pin

Signal Name

TPA1+

TPA1-

Ground

TPA2+

TPA2-

+12 V

Key (no pin)

Ground

Connecting to the Audio System
After installing the IDT audio driver from the Intel Express Installer DVD-ROM, the
multi-channel audio feature can be enabled. Figure 22 shows the back panel audio
connectors.

Item

Description

Rear Surround Left/Right

Center Channel and LFE (Subwoofer)

Side Surround/Line In

Line Out

Mic In

S/PDIF Digital Audio Out (Optical)

Figure 22. Back Panel Audio Connectors

Intel Desktop Board DG45ID Product Guide

NOTE
The back panel line out connector is designed to power either headphones or amplified
speakers only. Poor audio quality may occur if passive (non-amplified) speakers are
connected to this output.

Connecting Chassis Fan and Power Supply
Cables
Chassis Fan Cables
Connect chassis fan cables to the 3-pin and 4-pin chassis fan headers on the Desktop
Board. Figure 23 shows the location of the chassis fan headers.

Figure 23. Location of the Chassis Fan Headers

Installing and Replacing Desktop Board Components

Power Supply Cables
CAUTION
Failure to use an appropriate power supply and/or not connecting the 12 V (2 x 2 pin)
power connector to the Desktop Board may result in damage to the board or the
system may not function properly.
The 2 x 12 pin main power connector on the Desktop Board is backwards compatible
with ATX12V power supplies with 2 x 10 connectors. Figure 24 shows the location of
the Desktop Board power connectors.

Figure 24. Connecting Power Supply Cables
1. Observe the precautions in "Before You Begin" on page 27.
2. Connect the main power supply cable to the 2 x 12 pin connector.
3. Connect the 12 V processor core voltage power supply cable to the 2 x 2 pin
connector.

Intel Desktop Board DG45ID Product Guide

Setting the BIOS Configuration Jumper
NOTE
Always turn off the power and unplug the power cord from the computer before
moving the jumper. Moving the jumper with the power on may result in unreliable
computer operation.
Figure 25 shows the location of the Desktop Board’s BIOS configuration jumper block.

Figure 25. Location of the BIOS Configuration Jumper Block
The three-pin BIOS jumper block enables all board configurations to be done in the
BIOS Setup program. Table 16 shows the jumper settings for the BIOS Setup
program modes.

Installing and Replacing Desktop Board Components

Table 16. Jumper Settings for the BIOS Setup Program Modes
Jumper Setting

Mode

Description

Normal (default) (1-2)

The BIOS uses the current configuration and
passwords for booting.

Configure (2-3)

After the Power-On Self-Test (POST) runs, the
BIOS displays the Maintenance Menu. Use this
menu to clear passwords.

Recovery (None)

The BIOS recovers data in the event of a failed
BIOS update.

Clearing Passwords
This procedure assumes that the board is installed in the computer and the
configuration jumper block is set to normal mode.
1. Observe the precautions in "Before You Begin" on page 27.
2. Turn off all peripheral devices connected to the computer. Turn off the computer.
Disconnect the computer’s power cord from the AC power source (wall outlet or
power adapter).
3. Remove the computer cover.
4. Find the configuration jumper block (see Figure 25).
5. Place the jumper on pins 2-3 as shown below.

6. Replace the cover, plug in the computer, turn on the computer, and allow it to
boot.
7. The computer starts the Setup program. Setup displays the Maintenance menu.
8. Use the arrow keys to select Clear Passwords. Press and Setup displays a
pop-up screen requesting that you confirm clearing the password. Select Yes and
press . Setup displays the maintenance menu again.
9. Press to save the current values and exit Setup.
10. Turn off the computer. Disconnect the computer’s power cord from the AC power
source.

Intel Desktop Board DG45ID Product Guide

11. Remove the computer cover.
12. To restore normal operation, place the jumper on pins 1-2 as shown below.

13. Replace the cover, plug in the computer, and turn on the computer.

Replacing the Battery
A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When
the computer is not plugged into a wall socket, the battery has an estimated life of
three years. When the computer is plugged in, the standby current from the power
supply extends the life of the battery. The clock is accurate to ± 13 minutes/year at
25 ºC with 3.3 VSB applied.
When the voltage drops below a certain level, the BIOS Setup program settings stored
in CMOS RAM (for example, the date and time) might not be accurate. Replace the
battery with an equivalent one. Figure 26 on page 59 shows the location of the
battery.

PRECAUTION
Risque d'explosion si la pile usagée est remplacée par une pile de type incorrect. Les
piles usagées doivent être recyclées dans la mesure du possible. La mise au rebut des
piles usagées doit respecter les réglementations locales en vigueur en matière de
protection de l'environnement.

FORHOLDSREGEL
Eksplosionsfare, hvis batteriet erstattes med et batteri af en forkert type. Batterier
bør om muligt genbruges. Bortskaffelse af brugte batterier bør foregå i
overensstemmelse med gældende miljølovgivning.

OBS!
Det kan oppstå eksplosjonsfare hvis batteriet skiftes ut med feil type. Brukte batterier
bør kastes i henhold til gjeldende miljølovgivning.

Installing and Replacing Desktop Board Components

VIKTIGT!
Risk för explosion om batteriet ersätts med felaktig batterityp. Batterier ska kasseras
enligt de lokala miljövårdsbestämmelserna.

VARO
Räjähdysvaara, jos pariston tyyppi on väärä. Paristot on kierrätettävä, jos se on
mahdollista. Käytetyt paristot on hävitettävä paikallisten ympäristömääräysten
mukaisesti.

VORSICHT
Bei falschem Einsetzen einer neuen Batterie besteht Explosionsgefahr. Die Batterie
darf nur durch denselben oder einen entsprechenden, vom Hersteller empfohlenen
Batterietyp ersetzt werden. Entsorgen Sie verbrauchte Batterien den Anweisungen
des Herstellers entsprechend.

AVVERTIMENTO
Esiste il pericolo di un esplosione se la pila non viene sostituita in modo corretto.
Utilizzare solo pile uguali o di tipo equivalente a quelle consigliate dal produttore. Per
disfarsi delle pile usate, seguire le istruzioni del produttore.

PRECAUCIÓN
Existe peligro de explosión si la pila no se cambia de forma adecuada. Utilice
solamente pilas iguales o del mismo tipo que las recomendadas por el fabricante del
equipo. Para deshacerse de las pilas usadas, siga igualmente las instrucciones del
fabricante.

WAARSCHUWING
Er bestaat ontploffingsgevaar als de batterij wordt vervangen door een onjuist type
batterij. Batterijen moeten zoveel mogelijk worden gerecycled. Houd u bij het
weggooien van gebruikte batterijen aan de plaatselijke milieuwetgeving.

ATENÇÃO
Haverá risco de explosão se a bateria for substituída por um tipo de bateria incorreto.
As baterias devem ser recicladas nos locais apropriados. A eliminação de baterias
usadas deve ser feita de acordo com as regulamentações ambientais da região.

AŚCIAROŽZNAŚĆ
Існуе рызыка выбуху, калі заменены акумулятар неправільнага тыпу.
Акумулятары павінны, па магчымасці, перепрацоўвацца. Пазбаўляцца ад старых
акумулятараў патрэбна згодна з мясцовым заканадаўствам па экалогіі.

Intel Desktop Board DG45ID Product Guide

UPOZORNÌNÍ
V případě výměny baterie za nesprávný druh může dojít k výbuchu. Je-li to možné,
baterie by měly být recyklovány. Baterie je třeba zlikvidovat v souladu s místními
předpisy o životním prostředí.

Προσοχή
Υπάρχει κίνδυνος για έκρηξη σε περίπτωση που η μπαταρία αντικατασταθεί από μία
λανθασμένου τύπου. Οι μπαταρίες θα πρέπει να ανακυκλώνονται όταν κάτι τέτοιο είναι
δυνατό. Η απόρριψη των χρησιμοποιημένων μπαταριών πρέπει να γίνεται σύμφωνα με
τους κατά τόπο περιβαλλοντικούς κανονισμούς.

VIGYÁZAT
Ha a telepet nem a megfelelő típusú telepre cseréli, az felrobbanhat. A telepeket
lehetőség szerint újra kell hasznosítani. A használt telepeket a helyi környezetvédelmi
előírásoknak megfelelően kell kiselejtezni.

AWAS
Risiko letupan wujud jika bateri digantikan dengan jenis yang tidak betul. Bateri
sepatutnya dikitar semula jika boleh. Pelupusan bateri terpakai mestilah mematuhi
peraturan alam sekitar tempatan.

OSTRZEŻENIE
Istnieje niebezpieczeństwo wybuchu w przypadku zastosowania niewłaściwego typu
baterii. Zużyte baterie należy w miarę możliwości utylizować zgodnie z odpowiednimi
przepisami ochrony środowiska.

PRECAUŢIE
Risc de explozie, dacă bateria este înlocuită cu un tip de baterie necorespunzător.
Bateriile trebuie reciclate, dacă este posibil. Depozitarea bateriilor uzate trebuie să
respecte reglementările locale privind protecţia mediului.

ВНИМАНИЕ
При использовании батареи несоответствующего типа существует риск ее взрыва.
Батареи должны быть утилизированы по возможности. Утилизация батарей должна
проводится по правилам, соответствующим местным требованиям.

Installing and Replacing Desktop Board Components

UPOZORNENIE
Ak batériu vymeníte za nesprávny typ, hrozí nebezpečenstvo jej výbuchu. Batérie by
sa mali podľa možnosti vždy recyklovať. Likvidácia použitých batérií sa musí vykonávať
v súlade s miestnymi predpismi na ochranu životného prostredia.

POZOR
Zamenjava baterije z baterijo drugačnega tipa lahko povzroči eksplozijo.
Če je mogoče, baterije reciklirajte. Rabljene baterije zavrzite v skladu z lokalnimi
okoljevarstvenimi predpisi.

UYARI
Yanlış türde pil takıldığında patlama riski vardır. Piller mümkün olduğunda geri
dönüştürülmelidir. Kullanılmış piller, yerel çevre yasalarına uygun olarak atılmalıdır.

OСТОРОГА
Використовуйте батареї правильного типу, інакше існуватиме ризик вибуху.
Якщо можливо, використані батареї слід утилізувати. Утилізація використаних
батарей має бути виконана згідно місцевих норм, що регулюють охорону довкілля.

Intel Desktop Board DG45ID Product Guide

To replace the battery, follow these steps:
1. Observe the precautions in "Before You Begin" (see page 27).
2. Turn off all peripheral devices connected to the computer. Disconnect the
computer’s power cord from the AC power source (wall outlet or power adapter).
3. Remove the computer cover.
4. Locate the battery on the board (see Figure 26).
5. With a medium flat-bladed screwdriver, gently pry the battery free from its
connector. Note the orientation of the “+” and “-” on the battery.
6. Install the new battery in the connector, orienting the “+” and “-” correctly.
7. Replace the computer cover.

Installing and Replacing Desktop Board Components

Figure 26. Removing the Battery

Intel Desktop Board DG45ID Product Guide

3 Updating the BIOS
The BIOS Setup program can be used to view and change the BIOS settings for the
computer. You can access the BIOS Setup program by pressing the key after
the Power-On Self-Test (POST) memory test begins and before the operating system
boot begins.
This chapter tells you how to update the BIOS by either using the Intel Express BIOS
Update utility or the Iflash Memory Update utility, and how to recover the BIOS if an
update fails.

Updating the BIOS with the Intel® Express
BIOS Update Utility
With the Intel Express BIOS Update utility you can update the system BIOS while in
the Windows environment. The BIOS file is included in an automated update utility
that combines the functionality of the Intel® Flash Memory Update Utility and the ease
of use of Windows-based installation wizards.
To update the BIOS with the Intel Express BIOS Update utility:
1. Go to the Intel World Wide Web site:
http://support.intel.com/support/motherboards/desktop/
2. Navigate to the DG45ID page. Under the “Software and drivers” heading, click on
“Latest BIOS” to locate the latest BIOS files. Click on the “BIOS Update” link and
select the Express BIOS Update file.
3. Download the file to your hard drive. (You can also save this file to a removable
USB device. This is useful if you are updating the BIOS for multiple identical
systems.)
4. Close all other applications. This step is required. Your system will be rebooted at
the last Express BIOS Update window.
5. Double-click the executable file from the location on your hard drive where it was
saved. This runs the update program.
6. Follow the instructions provided in the dialog boxes to complete the BIOS update.

Intel Desktop Board DG45ID Product Guide

Updating the BIOS with the ISO Image BIOS
Update File or the Iflash Memory Update
Utility
You can use the information in this section to update the BIOS using either the Iflash
Memory Update Utility or the ISO Image BIOS update file.

Obtaining the BIOS Update File
You can update to a new version of the BIOS by using the ISO Image BIOS update file
(recommended), or Iflash BIOS update file.
The ISO Image BIOS update file is a standardized image of a bootable CD-ROM that
can be used to create a bootable CD that will update the BIOS.
The Iflash BIOS update file is a compressed file that contains the files you need to
update the BIOS. The Iflash BIOS update file contains:
•
•
•

New BIOS file (including the Intel® Management Engine (Intel® ME) Firmware
Image))
Intel® Integrator Toolkit Configuration File (optional)
Intel Flash Memory Update Utility

You can obtain either of these files through your computer supplier or by navigating to
the Desktop Board DG45ID page on the Intel World Wide Web site at
http://support.intel.com/support/motherboards/desktop.
Navigate to the DG45ID page. Under the “Software and drivers” heading, click on
“Latest BIOS” to locate the latest BIOS files. Click on the “BIOS Update” link and
select the ISO Image BIOS Update file or the Iflash BIOS Update file.

Updating the BIOS with the ISO Image BIOS Update
File
The ISO Image BIOS update allows for the update of an Intel® Desktop Board BIOS to
the latest production release regardless of the operating system installed on the
computer's hard drive and without the need to remove the BIOS configuration jumper.
It requires a blank CD-R, a read/writeable CD drive, and software capable of
uncompressing and writing the ISO image file to CD.
The image uses ISOLINUX* bootloader and automatically launches a script to upgrade
the BIOS via the Iflash utility.

Updating the BIOS

CAUTION
Do not interrupt the process or the system may not function properly.
Follow these instructions to upgrade the BIOS using the ISO Image BIOS file:
1. Download the ISO Image BIOS file.
2. Using software capable of uncompressing and writing an ISO image file to CD, burn
the data to a blank CD.

NOTE
Copying the ISO Image BIOS file to CD will not work. The completed CD should
contain multiple files and a directory.
3. Insert the CD that was created in the CD-ROM drive of the computer to be
upgraded and boot the system.
4. When the "Press ENTER to continue booting from CD-ROM" prompt appears, press
the Enter key. The system will boot from the hard drive if no key is pressed within
15 seconds.
5. At the "Welcome to the Intel Desktop Board BIOS Upgrade CD-ROM" page, press
any key to confirm the BIOS upgrade operation.
6. Wait for the BIOS upgrade process to complete.

CAUTION
DO NOT POWER DOWN YOUR COMPUTER before the update is complete. The update
may take up to 5 minutes.

Updating the BIOS with the Iflash Memory Update
Utility
With the Iflash Memory update utility you can update the system BIOS from a
bootable CD-ROM, bootable USB flash drive, or other bootable USB media. The utility
available on the Intel World Wide Web site provides a simple method for creating a
bootable CD-ROM that will automatically update your BIOS. The Iflash BIOS update
files can also be extracted locally to your hard drive and copied to a bootable USB
flash drive or other bootable USB media.
The Iflash Memory update utility allows you to:
•
•

Update the BIOS and Intel Management Engine in flash memory
Update the language section of the BIOS

NOTE
Review the instructions distributed with the update utility before attempting a BIOS
update.

Intel Desktop Board DG45ID Product Guide

CAUTION
Do not interrupt the process or the system may not function properly.
1. Uncompress the BIOS update file and copy the .BIO file, IFLASH.EXE, and .ITK file
(optional) to a bootable USB flash drive or other bootable USB media.
2. Configure the BIOS or use the F10 option during POST to boot to the USB device.
3. Manually run the IFLASH.EXE file from the USB device and manually update the
BIOS.

Recovering the BIOS
It is unlikely that anything will interrupt the BIOS update; however, if an interruption
occurs, the BIOS could be damaged. Due to BIOS size and recovery requirements, a
CD-R with the .BIO file in the root directory will be required.

NOTE
For more information about updating the Intel Desktop Board BIOS or recovering from
a BIOS update failure, go to
http://support.intel.com/support/motherboards/desktop/sb/CS-022312.htm.

4 Configuring for RAID (Intel® Matrix
Storage Technology (Intel® MST))
NOTE
Intel Matrix Storage Technology requires Microsoft Windows Vista or Microsoft
Windows XP operating system and SATA hard drives.

Configuring the BIOS for Intel Matrix Storage
Technology
1. Assemble your system and attach one or more SATA hard drives to the SATA
connectors.
2. Enter system BIOS Setup by pressing the key after the Power-On-Self-Test
(POST) memory tests begin.
3. Go to Advanced
Drive Configuration
Configure SATA as; ensure that
RAID is selected.
4. Then save your settings by pressing .

Creating Your RAID Set
1. Upon re-boot, you will see the following Intel Matrix Storage Manager option ROM
status message on the screen: Press to enter the RAID
Configuration Utility. Press and enter the RAID Configuration Utility.
2. In the Intel Matrix Storage Manager option ROM Main Menu, select option #1:
Create RAID Volume. Enter a volume name and press .
NOTE: The RAID Volume name must be in English alphanumeric ASCII characters.
3. Use the arrow keys to select RAID 0 or RAID 1 (if only two SATA drives are
available), RAID 5 and RAID 10 (these options will only appear if three or four
SATA drives are installed respectively). Press once you have selected the
RAID LEVEL.
4. Select the drives to be used in the RAID array (only if there are more than two
drives available) and press .
5. Select the strip size, if necessary, and press .
6. Enter the size of the volume (if you enter less than the maximum volume size, you
can then create a second RAID array on the remaining portion of your volume) and
press .
7. Finally, press to Create Volume.
8. Exit the Option ROM user interface by pressing or going to the EXIT option
in the MAIN MENU.

Intel Desktop Board DG45ID Product Guide

Loading the Intel Matrix Storage Technology RAID
Drivers and Software
1. Begin Windows Setup by booting from the Windows installation CD.
2. If you will be using Microsoft Windows XP, press at the beginning of Windows
Setup to install a third-party SCSI or RAID driver. When prompted, insert the
diskette labeled Intel Matrix Storage Technology RAID Driver. Install the Intel®
ICH10R SATA RAID Controller driver.
or
If you will be using Microsoft Windows Vista, follow the setup installation steps until
you reach the section "Where do you want to install Windows?". Click on the "Load
Drivers" option and insert the diskette labeled Intel Matrix Storage Technology
RAID Driver (Note: If you do not have a floppy drive, you can download the driver
from http://support.intel.com/support/motherboards/desktop/ to a recordable CD
or USB storage media). Select to install the Intel ICH10R SATA RAID Controller
driver.
3. Finish the Windows installation and install all necessary drivers.
4. Install the Intel Matrix Storage Console software via the Intel Express Installer CD
included with your desktop board or after downloading it from the Internet at
http://support.intel.com/support/motherboards/desktop/. The Intel Matrix Storage
Console software can be used to manage the RAID configuration.

Setting Up a “RAID Ready” System
The Intel Matrix Storage Technology Console software offers the flexibility to upgrade
from a single Serial ATA drive to RAID without reinstalling the operating system, when
a second SATA hard drive is added to the system.
Follow the steps described in the headings from this section: "Configuring the BIOS
for Intel Matrix Storage Technology" and "Loading the Intel Matrix Storage Technology
RAID Drivers and Software".
Once additional SATA drives have been added, open the Intel Matrix Storage
Technology Console Software and follow the directions to update to a RAID setup.

5 Configuring for Intel® Rapid
Recover Technology
Intel Rapid Recover technology utilizes RAID 1 (mirroring) functionality to copy data
from a designated master drive to a designated recovery drive. The master and
recovery drives must span 100 percent of the available hard drive space of an array,
and only one recovery volume can be present on a system.
You can select whether you want the master drive data to be copied to the recovery
drive continuously or on request. When using the Continuous Update policy, changes
made to the data on the master drive while the recovery drive is disconnected or
offline are automatically copied to the recovery drive when it is reconnected.
When using the Update On Request policy, the master drive data can be restored to a
previous state by copying the data on the recovery drive back to the master drive.

Enabling Intel Rapid Recover Technology
NOTE
Intel Rapid Recover Technology does not support RAID 5.
Intel Rapid Recover Technology can be Enabled or Disabled in the system BIOS menu.
To enable Intel Rapid Recover Technology, complete following steps:
1.
2.
3.
4.

Enter the BIOS menu by pressing the key early during system POST.
Go to Advanced
Drive Configuration.
For the setting Intel Rapid Recover Technology, select to enable it.
For the setting Configure SATA as, ensure it is set to RAID.

CAUTION
If Configure SATA as was previously not set to RAID and you already have an
operating system installed, you must reinstall it. Follow the instructions in
Chapter 4 to install the Intel Matrix Storage RAID driver during the operating
system installation.
5. Exit and save settings. Proceed to “Creating a Recovery Volume.”

Intel Desktop Board DG45ID Product Guide

Creating a Recovery Volume
A recovery volume consists of two disks – a master disk and a recovery disk.
A recovery volume can be created with either the RAID Option ROM (OROM) or the
Intel® Matrix Storage Console application.

Creating a Recovery Volume Using the RAID Option
ROM
To create a recovery volume using the RAID OROM, complete the following steps:
1. Enter the RAID OROM by pressing the and keys simultaneously when
prompted during system POST.
2. Under the Create RAID volume option, select the option to create a recovery
volume.
3. Select the master disk and the recovery disk.

NOTE
The master disk size must be less than or equal to the recovery disk size.
The RAID OROM Recovery menu provides the following options:
1. Disable Continuous Update
2. Boot from Recovery Disk
3. Boot from Master Disk

Creating a Recovery Volume Using the Intel Matrix
Storage Console
To create a recovery volume using the Intel Matrix Storage Console, the system must
be configured in RAID mode with two drives. Boot the system into Microsoft Windows
and open the Intel Matrix Storage Console application.
A recovery volume can be created in the Basic mode or the Advanced mode.
To create a recovery volume using the Basic mode, complete the following steps:
1. Select Protect data using Intel® Rapid Recover Technology.
2. A dialog box will pop up. Selecting Yes will start the volume creation process
which can be monitored on the progress bar.
To create a recovery volume using the Advanced mode, complete the following steps:
1.
2.
3.
4.
5.

Select
Select
Select
Select
Select

Advanced Mode in the View menu.
Create a Recovery Volume in the Actions menu.
Next to continue.
the master disk and select Next to continue.
the recovery disk and select Next to continue.

Configuring for Intel® Rapid Recover Technology

6. Select the Update policy – Continuous update or Update on request.
7. Select Finish to complete the creation of the recovery volume.
The system will synchronize the master disk with the recovery disk once after the
creation of the recovery volume.

Disk Synchronization Mode
There are two modes of updating or synchronizing the recovery disk with the master
disk – either continuous update or manual update.
To change from Continuous Update mode to Update On Request mode using the Intel
Matrix Storage Console, select the Advanced mode from the View menu, right-click
on the recovery volume, and select Disable Continuous Update.
To change from Update On Request mode to Continuous update mode, complete the
following steps:
1.
2.
3.
4.

Right-click on the recovery volume name and select Modify Volume.
Select Next on the Modify Recovery Volume Wizard dialog box to continue.
On the next screen, select Continuous update.
Select Next and then Finish to complete the operation.

Mounting the Recovery Disk
NOTE
Mounting the recovery disk will result in displaying the recovery disk in Microsoft
Windows Explorer. The recovery disk contents will be write-protected to preserve data
integrity with master disk.
To mount the mount the recovery disk, complete the following steps:
1. Make sure that the recovery volume is in Update On Request mode.
2. Then right-click on the recovery volume name and select Access Recovery Drive
Files.
3. Select OK on the information dialog box.
The recovery disk will now be mounted and can be seen in Microsoft Windows
Explorer.

NOTE
Individual files or folders can be copied from the recovery disk to the master disk. No
write operations can be performed on the recovery disk.

Intel Desktop Board DG45ID Product Guide

To un-mount the recovery disk, complete the following steps:
1. In the Advanced mode, right-click on the recovery volume name.
2. Select Access Recovery Drive Files.
3. Select OK on the information dialog box.
The recovery disk is now un-mounted and reappears in Intel Matrix Storage Console.

A Error Messages and Indicators
Desktop Board DG45ID reports POST errors in two ways:
•
•

By sounding a beep code
By displaying an error message on the monitor

BIOS Beep Codes
The BIOS also issues a beep code (one long tone followed by two short tones) during
POST if the video configuration fails (a faulty video card or no card installed) or if an
external ROM module does not properly checksum to zero. Table 17 lists the BIOS
codes.
Table 17. Beep Codes
Beep

Description

No memory

Siren

Processor overheat (on reboot)

BIOS Error Messages
When a recoverable error occurs during the POST, the BIOS displays an error message
describing the problem. Table 18 gives an explanation of the BIOS error messages.
Table 18. BIOS Error Messages
Error Message

Explanation

PROCESSOR_THERMAL_TRIP_ERROR

Processor was previously shutdown due to a thermal event
(overheating).

MULTI_BIT_ECC_ERROR

The firmware has detected that a Multi-Bit ECC Error occurred.

SINGLE_BIT_ECC_ERROR

The firmware has detected that a Single-Bit ECC Error occurred.

CMOS_BATTERY_ERROR

The firmware has detected that a CMOS battery failure occurred.

CMOS_CHECKSUM_ERROR

The firmware has detected that a CMOS Checksum Error occurred.

CMOS_TIMER_ERROR

The firmware has detected that the system date/time has not
been set.

MEMORY_SIZE_DECREASE_ERROR

The firmware has detected that the system memory has
decreased.

INTRUDER_DETECTION_ERROR

The system chassis was opened.

SPD_TOLER_ERROR

SERIAL PRESENCE DETECT (SPD) device data missing or
inconclusive. Properly programmed SPD device data is required
for reliable operation.

MEM_OPTIMAL_ERROR

The installed amount of memory in Channel A is not equal to the
amount of memory in Channel B. Maximum memory performance
is achieved with equal amounts of memory installed in each
channel.

Intel Desktop Board DG45ID Product Guide

B Regulatory Compliance
This appendix contains the following regulatory compliance information for Desktop
Board DG45ID:
•
•
•
•
•

Safety standards
European Union Declaration of Conformity statement
Product Ecology statements
Electromagnetic Compatibility (EMC) regulations
Product certifications

Safety Standards
Desktop Board DG45ID complies with the safety standards stated in Table 19 when
correctly installed in a compatible host system.
Table 19. Safety Standards
Regulation

Title

CSA/UL 60950-1, First
Edition

Information Technology Equipment – Safety - Part 1: General
Requirements (USA and Canada)

EN 60950-1:2006, Second
Edition

Information Technology Equipment – Safety - Part 1: General
Requirements (European Union)

IEC 60950-1:2005, Second
Edition

Information Technology Equipment – Safety - Part 1: General
Requirements (International)

Place Battery Marking
There is insufficient space on this Desktop Board to provide instructions for replacing
and disposing of the Lithium ion coin cell battery. For system safety certification, the
statement below or an equivalent statement is required to be permanently and legibly
marked on the chassis near the battery.

CAUTION
Risk of explosion if the battery is replaced with an incorrect type. Batteries should be
recycled where possible. Disposal of used batteries must be in accordance with local
environmental regulations.
A suitable caution label is included with Desktop Board DG45ID.
For information about replacing the battery, go to page 54.

Intel Desktop Board DG45ID Product Guide

European Union Declaration of Conformity
Statement
We, Intel Corporation, declare under our sole responsibility that the product Intel®
Desktop Board DG45ID is in conformity with all applicable essential requirements
necessary for CE marking, following the provisions of the European Council Directives
2004/108/EC (EMC Directive) and 2006/95/EC (Low Voltage Directive).
The product is properly CE marked demonstrating this conformity and is for
distribution within all member states of the EU with no restrictions.

This product follows the provisions of the European Directives 2004/108/EC and
2006/95/EC.
Čeština Tento výrobek odpovídá požadavkům evropských směrnic 2004/108/EC a
2006/95/EC.
Dansk Dette produkt er i overensstemmelse med det europæiske direktiv
2004/108/EC & 2006/95/EC.
Dutch Dit product is in navolging van de bepalingen van Europees Directief
2004/108/EC & 2006/95/EC.
Eesti Antud toode vastab Euroopa direktiivides 2004/108/EC ja 2006/95/EC
kehtestatud nõuetele.
Suomi Tämä tuote noudattaa EU-direktiivin 2004/108/EC & 2006/95/EC määräyksiä.
Français Ce produit est conforme aux exigences de la Directive Européenne
2004/108/EC & 2006/95/EC.
Deutsch Dieses Produkt entspricht den Bestimmungen der Europäischen Richtlinie
2004/108/EC & 2006/95/EC.
Ελληνικά Το παρόν προϊόν ακολουθεί τις διατάξεις των Ευρωπαϊκών Οδηγιών
2004/108/EC και 2006/95/EC.
Magyar E termék megfelel a 2004/108/EC és 2006/95/EC Európai Irányelv
előírásainak.
Icelandic Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer
2004/108/EC & 2006/95/EC.
Italiano Questo prodotto è conforme alla Direttiva Europea 2004/108/EC &
2006/95/EC.
Latviešu Šis produkts atbilst Eiropas Direktīvu 2004/108/EC un 2006/95/EC
noteikumiem.
Lietuvių Šis produktas atitinka Europos direktyvų 2004/108/EC ir 2006/95/EC
nuostatas.

Regulatory Compliance

Malti Dan il-prodott hu konformi mal-provvedimenti tad-Direttivi Ewropej
2004/108/EC u 2006/95/EC.
Norsk Dette produktet er i henhold til bestemmelsene i det europeiske direktivet
2004/108/EC & 2006/95/EC.
Polski Niniejszy produkt jest zgodny z postanowieniami Dyrektyw Unii Europejskiej
2004/108/EC i 2006/95/EC.
Portuguese Este produto cumpre com as normas da Diretiva Européia 2004/108/EC
& 2006/95/EC.
Español Este producto cumple con las normas del Directivo Europeo 2004/108/EC &
2006/95/EC.
Slovensky Tento produkt je v súlade s ustanoveniami európskych direktív
2004/108/EC a 2006/95/EC.
Slovenščina Izdelek je skladen z določbami evropskih direktiv 2004/108/EC in
2006/95/EC.
Svenska Denna produkt har tillverkats i enlighet med EG-direktiv 2004/108/EC &
2006/95/EC.
Türkçe Bu ürün, Avrupa Birliği’nin 2004/108/EC ve 2006/95/EC yönergelerine uyar.

Product Ecology Statements
The following information is provided to address worldwide product ecology concerns
and regulations.

Recycling Considerations
As part of its commitment to environmental responsibility, Intel has implemented the
Intel® Product Recycling Program to allow retail consumers of Intel’s branded products
to return used products to selected locations for proper recycling.
Please consult http://intel.com/intel/other/ehs/product_ecology
for the details of this program, including the scope of covered products, available
locations, shipping instructions, terms and conditions, etc.
中文
作为其对环境责任之承诺的部分，英特尔已实施 Intel Product Recycling Program
（英特尔产品回收计划），以允许英特尔品牌产品的零售消费者将使用过的产品退还至指定地点作恰
当的重复使用处理。
请参考http://intel.com/intel/other/ehs/product_ecology
了解此计划的详情，包括涉及产品之范围、回收地点、运送指导、条款和条件等。

Intel Desktop Board DG45ID Product Guide

Deutsch
Als Teil von Intels Engagement für den Umweltschutz hat das Unternehmen das Intel
Produkt-Recyclingprogramm implementiert, das Einzelhandelskunden von Intel
Markenprodukten ermöglicht, gebrauchte Produkte an ausgewählte Standorte für
ordnungsgemäßes Recycling zurückzugeben.
Details zu diesem Programm, einschließlich der darin eingeschlossenen Produkte,
verfügbaren Standorte, Versandanweisungen, Bedingungen usw., finden Sie auf der
http://intel.com/intel/other/ehs/product_ecology
Español
Como parte de su compromiso de responsabilidad medioambiental, Intel ha
implantado el programa de reciclaje de productos Intel, que permite que los
consumidores al detalle de los productos Intel devuelvan los productos usados en los
lugares seleccionados para su correspondiente reciclado.
Consulte la http://intel.com/intel/other/ehs/product_ecology
para ver los detalles del programa, que incluye los productos que abarca, los lugares
disponibles, instrucciones de envío, términos y condiciones, etc.
Français
Dans le cadre de son engagement pour la protection de l'environnement, Intel a mis
en œuvre le programme Intel Product Recycling Program (Programme de recyclage
des produits Intel) pour permettre aux consommateurs de produits Intel de recycler
les produits usés en les retournant à des adresses spécifiées.
Visitez la page Web http://intel.com/intel/other/ehs/product_ecology pour en savoir
plus sur ce programme, à savoir les produits concernés, les adresses disponibles, les
instructions d'expédition, les conditions générales, etc.
日本語
インテルでは、環境保護活動の一環として、使い終えたインテル
ブランド製品を指定の場所へ返送していただき、リサイクルを適切に行えるよう、インテル製品リサイクル
プログラムを発足させました。
対象製品、返送先、返送方法、ご利用規約など、このプログラムの詳細情報は、http://intel.com/intel/ot
her/ehs/product_ecology （英語）をご覧ください。
Malay
Sebagai sebahagian daripada komitmennya terhadap tanggungjawab persekitaran,
Intel telah melaksanakan Program Kitar Semula Produk untuk membenarkan
pengguna-pengguna runcit produk jenama Intel memulangkan produk terguna ke
lokasi-lokasi terpilih untuk dikitarkan semula dengan betul.
Sila rujuk http://intel.com/intel/other/ehs/product_ecology untuk mendapatkan butirbutir program ini, termasuklah skop produk yang dirangkumi, lokasi-lokasi tersedia,
arahan penghantaran, terma & syarat, dsb.

Regulatory Compliance

Portuguese
Como parte deste compromisso com o respeito ao ambiente, a Intel implementou o
Programa de Reciclagem de Produtos para que os consumidores finais possam enviar
produtos Intel usados para locais selecionados, onde esses produtos são reciclados de
maneira adequada.
Consulte o site http://intel.com/intel/other/ehs/product_ecology (em Inglês) para
obter os detalhes sobre este programa, inclusive o escopo dos produtos cobertos, os
locais disponíveis, as instruções de envio, os termos e condições, etc.
Russian
В качестве части своих обязательств к окружающей среде, в Intel создана
программа утилизации продукции Intel (Product Recycling Program) для
предоставления конечным пользователям марок продукции Intel возможности
возврата используемой продукции в специализированные пункты для должной
утилизации.
Пожалуйста, обратитесь на веб-сайт
http://intel.com/intel/other/ehs/product_ecology за информацией об этой
программе, принимаемых продуктах, местах приема, инструкциях об отправке,
положениях и условиях и т.д.
Türkçe
Intel, çevre sorumluluğuna bağımlılığının bir parçası olarak, perakende tüketicilerin
Intel markalı kullanılmış ürünlerini belirlenmiş merkezlere iade edip uygun şekilde geri
dönüştürmesini amaçlayan Intel Ürünleri Geri Dönüşüm Programı’nı uygulamaya
koymuştur.
Bu programın ürün kapsamı, ürün iade merkezleri, nakliye talimatları, kayıtlar ve
şartlar v.s dahil bütün ayrıntılarını ögrenmek için lütfen
http://intel.com/intel/other/ehs/product_ecology web sayfasına gidin.

Intel Desktop Board DG45ID Product Guide

Lead-free 2LI/Pb-free 2LI Board
The electronics industry is transitioning to European Union (EU) Restriction of
Hazardous Substances (RoHS)-compliant products. The RoHS legislation restricts the
use of six materials. One of these restricted materials is lead. Lead is the most
common and problematic of the RoHS restricted materials.
There are exemptions in RoHS that allow the use of lead in some very limited locations
in electronic products. Maximum lead concentration values have been established for
RoHS-compliant electronic products that allow up to 1000 ppm of lead.
Lead-free/Pb-free is a nickname that is often used (or misused) for RoHS-compliant
products. In this case, the term "Lead-free/Pb-free" means that lead has been
removed where required by the RoHS legislation but still may exist as an impurity
below 1000 ppm.
The term "Lead-free 2LI/Pb-free 2LI" means lead-free second level interconnect (2LI).
The balls, leads, or pads used to connect the component to a printed circuit board are
lead-free, but the first level interconnect (FLI) is not lead-free. The use of lead in the
FLI is acceptable because of the RoHS "flip chip" or "die bump" interconnect
exemption.
Desktop Board DG45ID is a lead-free second level interconnect product. Table 20
shows the lead-free second level interconnect marks as they appear on the board and
accompanying collateral. These marks are based on JEDEC standard J-STD-609,
“Marking and Labeling of Components, PCBs and PCBAs to Identify Lead, Lead Free
and Other Attributes.”
For more information concerning Intel’s lead-free initiatives, refer to
http://intel.com/technology/silicon/leadfree.htm.

Regulatory Compliance

Table 20. Lead-Free Second Level Interconnect Marks
Description

Mark

This symbol is used to identify
electrical and electronic
assemblies and components in
which the Pb concentration
level in the Desktop Board
substrate and the solder
connections from the board to
the components (second-level
interconnect) is not greater
than 0.1% by weight
(1000 ppm).

Restriction of Hazardous Substances (RoHS)
EU RoHS
EU RoHS Directive 2002/95/EC restricts the use of the following six materials in
various types of electronic and electrical equipment:
•
•
•
•
•
•

Lead
Mercury
Cadmium
Hexavalent chromium
Polybrominated biphenyls (PBB)
Polybrominated diphenyl ether (PBDE)

The maximum concentrations allowed are 0.1% or 1000 ppm (except for cadmium,
which is limited to 0.01% or 100 ppm) by weight of homogeneous material.
Desktop Board DG45ID complies with these restrictions.

Intel Desktop Board DG45ID Product Guide

China RoHS
“China RoHS” is the term used by industry generally to describe legislation
implemented by the Ministry of Information Industry (MII) in the People's Republic of
China for the control of pollution by electronic information products (EIP). The official
title of the China RoHS regulation is “Management Methods for Controlling Pollution by
Electronic Information Products.”
China RoHS bans the same substances and has the same limits as EU RoHS.
However, the China RoHS regulation requires specific product marking and a selfdeclaration of the controlled substances contained in each product.
Desktop Board DG45ID is a China RoHS-compliant product.
The required China RoHS mark indicates the product’s Environmental Friendly Usage
Period (EFUP). The EFUP is defined as the number of years for which listed controlled
substances will not leak or chemically deteriorate while in the product. The EFUP for
Intel Desktop Boards has been determined to be 10 years.
The EFUP for Desktop Board DG45ID is shown in Table 21.
Table 21. China RoHS Environmentally Friendly Use Period Mark
Description
This is an example of the
symbol used on Intel Desktop
Boards and associated
collateral. The color of the
mark may vary depending
upon the application. The
Environmental Friendly Usage
Period (EFUP) for Intel
Desktop Boards has been
determined to be 10 years.

Mark

Regulatory Compliance

The China MII stipulates that a material Self Declaration Table (SDT) must be included
in a product’s user documentation. The SDT for Desktop Board DG45ID is shown in
Figure 27.

Figure 27. Desktop Board DG45ID China RoHS Material
Self Declaration Table

Intel Desktop Board DG45ID Product Guide

EMC Regulations
Desktop Board DG45ID complies with the EMC regulations stated in Table 22 when
correctly installed in a compatible host system.
Table 22. EMC Regulations
Regulation (Class B)

Title

FCC 47 CFR Part 15,
Subpart B

Title 47 of the Code of Federal Regulations, Part 15, Subpart B,
Radio Frequency Devices. (USA)

ICES-003 Issue 4

Interference-Causing Equipment Standard, Digital Apparatus.
(Canada)

EN55022:2006

Limits and methods of measurement of Radio Interference
Characteristics of Information Technology Equipment. (European
Union)

EN55024:1998

Information Technology Equipment – Immunity Characteristics
Limits and methods of measurement. (European Union)

EN55022:2006

Australian Communications Authority, Standard for
Electromagnetic Compatibility. (Australia and New Zealand)

CISPR 22:2005
+A1:2005 +A2:2006

Limits and methods of measurement of Radio Disturbance
Characteristics of Information Technology Equipment.
(International)

CISPR 24:1997
+A1:2001 +A2:2002

Information Technology Equipment – Immunity Characteristics –
Limits and Methods of Measurement. (International)

VCCI V-3/2007.04,
V-4/2007.04

Voluntary Control for Interference by Information Technology
Equipment (Japan)

Japanese Kanji statement translation: This is a Class B product based on the standard
of the Voluntary Control Council for Interference from Information Technology
Equipment (VCCI). If this is used near a radio or television receiver in a domestic
environment, it may cause radio interference. Install and use the equipment
according to the instruction manual.

Regulatory Compliance

Korean Class B statement translation: This is household equipment that is certified to
comply with EMC requirements. You may use this equipment in residential
environments and other non-residential environments.

Ensure Electromagnetic Compatibility (EMC)
Compliance
Before computer integration, make sure that the power supply and other modules or
peripherals, as applicable, have passed Class B EMC testing and are marked
accordingly.
Pay close attention to the following when reading the installation instructions for the
host chassis, power supply, and other modules:
•
•
•
•

Product certifications or lack of certifications
External I/O cable shielding and filtering
Mounting, grounding, and bonding requirements
Keying connectors when mating the wrong connectors could be hazardous

If the power supply and other modules or peripherals, as applicable, are not Class B
EMC compliant before integration, then EMC testing may be required on a
representative sample of the newly completed computer.

Intel Desktop Board DG45ID Product Guide

Product Certifications
Board-Level Certification Markings
Desktop Board DG45ID has the product certification markings shown in Table 23.
Table 23. Product Certification Markings
Description

Mark

UL joint US/Canada Recognized Component mark. Includes adjacent
UL file number for Intel Desktop Boards: E210882.
FCC Declaration of Conformity logo mark for Class B equipment.
Includes Intel name and DG45ID model designation.

CE mark. Declaring compliance to European Union (EU) EMC
directive and Low Voltage directive.

Australian Communications Authority (ACA) and New Zealand Radio
Spectrum Management (NZ RSM) C-tick mark. Includes adjacent
Intel supplier code number, N-232.
Japan VCCI (Voluntary Control Council for Interference) mark.

S. Korea MIC (Ministry of Information and Communication) mark.
Includes adjacent MIC certification number: CPU-DG45ID (B).
Taiwan BSMI (Bureau of Standards, Metrology and Inspections)
mark. Includes adjacent Intel company number, D33025.
Printed wiring board manufacturer’s recognition mark. Consists of a
unique UL recognized manufacturer’s logo, along with a flammability
rating (solder side).

V-0

Regulatory Compliance

Chassis and Component Certifications
Ensure that the chassis and certain components; such as the power supply, peripheral
drives, wiring, and cables; are components certified for the country or market where
used. Agency certification marks on the product are proof of certification. Typical
product certifications include:
In Europe
The CE marking signifies compliance with all applicable European requirements. If the
chassis and other components are not properly CE marked, a supplier’s Declaration of
Conformity statement to the European EMC directive and Low Voltage directive (as
applicable), should be obtained. Additionally, other directives, such as the Radio and
Telecommunications Terminal Equipment (R&TTE) directive may also apply depending
on product features.
In the United States
A certification mark by a Nationally Recognized Testing Laboratory (NRTL) such as UL,
CSA, or ETL signifies compliance with safety requirements. Wiring and cables must
also be UL listed or recognized and suitable for the intended use. The FCC Class B
logo for home or office use signifies compliance with electromagnetic interference
(EMI) requirements.
In Canada
A nationally recognized certification mark such as CSA or cUL signifies compliance with
safety requirements. The Industry Canada statement at the front of this product guide
demonstrates compliance with Canadian EMC regulations.

Intel Desktop Board DG45ID Product Guide

Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Page Mode : UseOutlines XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Producer : Acrobat Distiller 8.1.0 (Windows) Creator Tool : Acrobat PDFMaker 8.1 for Word Modify Date : 2008:05:19 13:54:22-07:00 Create Date : 2008:05:08 16:22:57-07:00 Metadata Date : 2008:05:19 13:54:22-07:00 Format : application/pdf Creator : Intel Corporation Title : Intel® Desktop Board DG45IDProduct Guide Document ID : uuid:1423a36c-a30d-4de8-95db-cddff234293e Instance ID : uuid:322daad6-ec99-4923-a191-5c999551a8c3 Company : Intel Page Count : 86 Page Layout : OneColumn Author : Intel Corporation
EXIF Metadata provided by EXIF.tools

Intel DG45ID Intel® Desktop Board DG45IDProduct Guide User Manual To The F39bbd1b 505f 42eb B66f 4981764f8e46

Navigation menu

Versions of this User Manual:

Views

Navigation