Intel RCM24G Intel Radio Control Module 2.4 GHz User Manual User manual FCC ISED

Intel Corporation Intel Radio Control Module 2.4 GHz User manual FCC ISED

Contents

User_manual_FCC_ISED

Page 1 of 5 Intel® Radio Control Module 2.4 GHz Model: RCM24G Manual (US/CAN) Revision 1.0 Revision History Revision Description Date 1.0 RCM24G Modular Approval US/Canada 01.04.2017 Overview The RCM24G is a data transceiving module for wireless communication between two or more nodes of this kind. Instruction Do only use - with specified antennas - within specified supply voltage range - interfacing via UART/CAN-Bus
Page 2 of 5 Specification: Module output (Frequencies) 70 Hopping channels from 2402.5 MHz (Channel 0) to 2471.5MHz (Channel 69), 1MHz channel spacing, ADFSS Modulation MSK modulation Receiver Bandwidth 232kHz, 540kHz, 812.5kHz Datarate 50kbit/s, 100kbit/s, 250kbit/s and 500kbit/s Dwell Time 10ms (500kbit/s) to 28ms (50kbit/s). Fixed amount of useable data per hop (128 bytes TX and 128 byte RX) CCA Inactive Supply Input range 3.6 VDCV ± 5% / 1A Testing Antennas 1x Intel® FA5 antenna (HW-Version: Antenna-002) with 5 ports 1x Prestta WLAN Embedded Antenna P/N: 1000418 50 Ohm unbalanced Antenna connection µUFL Connector type: 50 Ohm nominal Permissive antenna type/gain Type: (Circularly polarized) patch antenna Max. antenna gain: 4.86 dBi Type: Dipole Max. antenna gain: 2.5 dBi Antenna configuration 1 antenna/module Transmitter Output Power Channel Max. power 0-3 10.19 dBm 4-7 10.72 dBm 8-10 12.84 dBm 11-14 14.71 dBm 15-17 16.37 dBm 18-21 17.92 dBm 22-24 19.05 dBm 25-39 19.93 dBm 40-43 18.81 dBm 44-48 17.79 dBm 49-52 16.19 Bm 53-57 14.51 dBm 58-61 12.49 dBm 62-66 10.36 dBm 67-69 9.32 dBm Table 1 Max. Power Settings Operational Characteristics Hopping mode A user serial number is used to generate a 70 hop long pseudo random hopping sequence which is contains each channel exactly once and is repeated every 70 hops.
Page 3 of 5 Diversity Mode The RCM24G module is designed to work in the following diversity mode: Two adjacent modules transmit parallel with full power. The pseudo random hopping frequency along with dissimilar seeding ensures that both modules never occupy the same channel at a time. CCA is not performed. Connection Figure 1 RCM24G Bottom View Figure 2 RCM24G Top View Pin Signal Designation Pin Signal Designation 1 V_sup 3.3V 2 GND GND 3 UART2 TX 4 UART2 RX 5 I/O General I/O 6 I/O General I/O 7 UART 3 TX 8 UART 3 RX 9 CAN RX 10 CAN TX Table 2: Transmitter Host Connector THC (Transmitter Host Connector) antenna 1 10
Page 4 of 5 FCC and ISED Statement This device complies with Part 15 of the FCC Rules and with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'autorisation d’exploitation est soumise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de d’interférences radioélectriques, et (2) l'appareil doit accepter toute interference radioélectrique subi, même si le brouillage est susceptible d'en compromettre le bon fonctionnement. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced radio/TV technician for help. ICES-003 Statement (Canada) This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Canadian Department of Communications. Cet appareil numérique respecte les limites bruits radioélectriques applicables aux appareils numériques de Classe B prescrites dans la norme relatives aux interferences causée par du matériel: “Appareils Numériques”, NMB-003 édictée par le Ministre Canadian des Communications. i. the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; i. Le dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques d’interférence préjudiciable aux systèmes de téléphonie satellitaire utilisant les mêmes canaux; ii. high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 ii. De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux
Page 5 of 5 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. (c.-à-d., qu’ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer des interférenceset/ou des dommages aux dispositifs LAN-EL. iii. for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit; iii. Pour les dispositifs dotés d'antenne (s) amovible (s), le gain d'antenne maximal autorisé pour les dispositifs dans les bandes 5250-5350 MHz et 5470-5725 MHz doit être tel que l'équipement soit toujours conforme aux normes e.i.r.p. limite; iv. for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725- 5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point- to-point and non-point-to-point operation as appropriate iv. Pour les dispositifs dotés d'antenne (s) amovible (s), le gain d'antenne maximal autorisé pour les dispositifs de la bande 5725- 5850 MHz doit être tel que l'équipement soit toujours conforme aux normes e.i.r.p. Limites spécifiées pour les opérations point à point et non point-à-point selon le cas Important Note Changes or modifications made to this equipment not expressly approved by Intel Corporation may void the FCC authorization to operate this equipment. The product is provided with an approved antenna. Use only supplied or approved antenna by Intel Corporation. Any changes or modifications to the Antenna may void the FCC regulatory approvals obtained for the product. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. RF exposure compliance must be ensured by integrator. Contact Intel Corporation 2200 Mission College Boulevard Santa Clara, CA 95054

Navigation menu