Intel VLMTX58G Intel Video Link Module Tx 5.8 GHz User Manual

Intel Corporation Intel Video Link Module Tx 5.8 GHz

User manual

Page 1 of 5 Intel® Video Link Module Tx 5.8 GHz Model: VLMTX58G Manual (USA, Canada) Revision 1.0 Revision History Revision Description Date 1.0 VLMTX58G – Module Change in ID and Multiple Listing for USA and Canada 2017-03-17 Overview The VLMTX58G is the image transmitting device of a wireless video link system consisting of a VLMTX58G transmitter and a VLMRX58G receiver/transceiver. Instruction Do only use - with specified antennas - within specified supply voltage range - interfacing via provided HDMI, USB port, THC connector.
Page 2 of 5 Specification Module output (frequencies) 5.15 GHz – 5.25 GHz 5.25 GHz – 5.35 GHz (DFS) 5.470 GHz – 5.725 GHz (DFS) 5.725 GHz – 5.85 GHz DFS Operation Client (without radar detection) Modulation OFDM 16QAM (similar to 802.11a/n) on a proprietary protocol Bandwidth 10 MHz, 20 MHz 40 MHz Data Rates 10 MHz mode: 18.11 Mbps 20 MHz mode: 36.23 Mbps 40 MHz mode: 72.46 Mbps Supply Input range 5 VDCV ± 10% / 1A Antenna connection RP-SMA male Connector type: 50 Ohm nominal Permissive antenna type/gain Manufacturer: STEREN Model: WIFI Internal Antenna 3070-09-350 P/N: 3070-09-350 Peak Gain: 2.0 dBi Antenna configuration uncorrelated MIMO with 2 antennas multiplexed to 2x transmitting RF ports and 1 x receiving RF antenna port Module Input HDMI Transmitter Output Power Band USA output power Canada output power Band 1 5.15 GHz – 5.25 GHz 24 dBm (conducted) 23 dBm (EIRP) Band 2 5.25 GHz - 5.35 GHz 24 dBm (conducted) 23 dBm (EIRP) Band 3 5.470 GHz - 5.725 GHz 24 dBm (conducted) 24 dBm (conducted) Band 4 5.725 GHz – 5.85 GHz 24 dBm (conducted) 24 dBm (conducted)
Page 3 of 5 Connection Figure 1 VLMTX58G Top View Figure 2 VLMTX58G Bottom View Pin Signal Designation Pin Signal Designation 2 VCC_5V +5V 1 VCC_5V +5V 4 VCC_5V +5V 3 VCC_5V +5V 6 VCC_5V +5V 5 VCC_5V +5V 8 GND8 GND 7 GND5 GND 10 NC 9 GND4 GND 12 LED1 +3.3V (Video Indication) 11 Spare2 +3.3V PC5. Pull down using 4.7KOhm 14 LED2 +3.3V (Network Indication) 13 Spare1 +3.3V PC2. Pull down using 4.7KOhm 16 Link/ Boot Mode GPIO Active low (start registration in low). Keep high or NC when not in use 15 Reset Active Low 18 NC 17 NC 20 NC 19 NC 22 NC 21 NC 24 NC 23 Reserved 3.3V Pull down using 4.7KOhm 26 NC 25 Reserved NC 28 NC 27 Reserved 3.3V Pull down using 4.7KOhm 30 GND7 GND 29 GND3 GND 32 Reserved Pull Down using 4.7KOhm 31 GND2 GND 34 NC 33 Reserved NC 36 NC 35 Reserved NC 38 Reserved NC 37 UART4_RX +3.3V MAVLink 40 Reserved NC 39 UART4_TX +3.3V MAVLink 42 Reserved NC 41 Reserved Keep NC 44 Reserved NC 43 Reserved Keep NC 46 Reserved NC 45 Reserved Keep NC 48 Reserved NC 47 Reserved Keep NC 50 GND6 GND 49 GND1 GND Table 1:Transmitter Host Connector Antenna 1 N/C Antenna 2 HDMI in USB 1 50 THC
Page 4 of 5 FCC and ISED Statement This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'autorisation d’exploitation est soumise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de d’interférences radioélectriques, et (2) l'appareil doit accepter toute interference radioélectrique subi, même si le brouillage est susceptible d'en compromettre le bon fonctionnement. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced radio/TV technician for help. ICES-003 Statement (Canada) This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Canadian Department of Communications. Cet appareil numérique respecte les limites bruits radioélectriques applicables aux appareils numériques de Classe B prescrites dans la norme relatives aux interferences causée par du matériel: “Appareils Numériques”, NMB-003 édictée par le Ministre Canadian des Communications. i. the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; i. Le dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques d’interférence préjudiciable aux systèmes de téléphonie satellitaire utilisant les mêmes canaux; ii. high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. ii. De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer des interférenceset/ou des dommages aux dispositifs LAN-EL.
Page 5 of 5 iii. for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit; iii. Pour les dispositifs dotés d'antenne (s) amovible (s), le gain d'antenne maximal autorisé pour les dispositifs dans les bandes 5250-5350 MHz et 5470-5725 MHz doit être tel que l'équipement soit toujours conforme aux normes e.i.r.p. limite; iv. for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725- 5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point- to-point and non-point-to-point operation as appropriate iv. Pour les dispositifs dotés d'antenne (s) amovible (s), le gain d'antenne maximal autorisé pour les dispositifs de la bande 5725- 5850 MHz doit être tel que l'équipement soit toujours conforme aux normes e.i.r.p. Limites spécifiées pour les opérations point à point et non point-à-point selon le cas Important Note Changes or modifications made to this equipment not expressly approved by Intel Corporation may void the FCC and ISED authorization to operate this equipment. The product is provided with an approved antenna. Use only supplied or approved antenna by Intel Corporation. Any changes or modifications to the Antenna may void the FCC and ISED regulatory approvals obtained for the product. Les modifications ou modifications apportées à cet équipement qui ne sont pas expressément approuvées par Intel Corporation peuvent annuler l'autorisation de la FCC et de l'ISED pour utiliser cet équipement. Le produit est fourni avec une antenne approuvée. Utilisez uniquement une antenne fournie ou approuvée par Intel Corporation. Toute modification ou modification de l'antenne peut annuler les certifications réglementaires FCC et ISED obtenues pour le produit. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Operations in the 5150 - 5250 MHz band are restricted to indoor usage only. This device is not allowed to operate in the 5600-5650 MHz band as required by Canada regulation (ISED). The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. RF exposure compliance must be ensured by integrator. Contact Intel Corporation 2200 Mission College Boulevard Santa Clara, CA 95054

Navigation menu