NX 6V2 Control Panel Installation Instructions 466 2338 REV B Install

: InterLogix 466-2338 Rev B Install Instructions 466-2338 REV B Install Instructions library

Open the PDF directly: View PDF .
Page Count: 10

NX-6V2 Control Panel Installation Instructions

Introduction

This is the NX-6V2-Control Panel Installation Instructions.

Installations should only be done by trained professionals. Use

this document to install the system with default settings that

comply with UL requirements.

To install the keypad, other peripherals, and sensors, refer to

the documentation for those devices.

Installation

There are four slots for board insertions inside the metal

enclosure, two on the top and two on the bottom. These allow

the PC board to be positioned vertically (Figure 1). When you

slide the board between the grooves of the slots, make sure

the terminal strip is toward the front opening (toward you) to

allow for the wire connections.

Note: Install the metal enclosure with the door opening from

the top to bottom.

Figure 1 Board Installation

NetworX keypad maximum wire run

Table 1 lists wire lengths for one keypad at the end of the wire.

When connecting more than one keypad to the end of the wire,

a higher gauge wire is required

Table 1: Maximum keypad wire run

Length in feet Wire gauge for NX-6v2 Wire gauge for NX320-E

250 24 22

500 20 18

1000 18 16

1500 16 14

2000 14 12

Terminal descriptions

Table 2 describes the panel terminals

Table 2: NX-6V2 Terminals

Terminal Description

R1 House telephone ring (grey).

R Telephone ring (red).

T Telephone tip (green).

T1 House telephone tip (brown).

EARTH Earth ground. Connect to a cold water pipe or a 6 to

10 ft. driven rod.

A

C AC input. Connect to a 16.5 V, 40 or 50 VA Class II

UL approved transformer.

Bell + and

Bell -

If used as a siren output (default), the speaker rating

should be 15 watt at 8 or 16 ohm, or 30/40 watt at 4,

8, or 16 ohms. If voltage ouput is selected in location

37, this output becomes voltage output, 12 VDC, 1

Amp maximum load. Note: A 3.3 kohm resistor may

be required across the bell terminals when a 12 VDC

siren is used. If no resistor is used, you may

experience voltage leakage into the siren, which will

cause these devices to output a small signal.

KP DATA Connect to the data terminal on the keypads and the

expanders. Maximum number of devices is 16

keypads plus 3 other de vices. See Maximum Wire

Run table.

KP COM Connect to the common terminal on the keypads and

the expanders.

KP POS Connect to the POS terminal on the keypads and the

expanders. Individually, this terminal is limited to 1

amp. Combined, this terminal and AUX PWR+ are

limited to 2 amps total current.

COM Common negative wire of powered devices such as

motion detectors and smoke detectors.

A

UXPWR + Connect positive wire of all powered devices except

smoke detectors and keypads. Individually, this

terminal is limited to 1 amp. Combined, this terminal

and KP POS are limited to 2 amps total current.

P/N 466-2338 • REV B • January 2011 1

ZONE 7 Connect to one side of zone 6 loop. Connect the

other side to com terminal. Open or short causes

alarm. Only zone 6 can be used for a two-wire

smoke detector, connected with a 680 ohm EOL

resistor. Refer to the wiring diagram. Program

location 37, segment 6, option 1. Only zone 6 can be

a two-wire zone.

COM Common (-) terminal for zones 5 and 6.

ZONE 6 Connect to one side of zone 5 loop. Connect the

other side to COM terminal. Open or short causes

alarm.

ZONES 1 to 5 Connect as described for zones 5 and 6.

A

UXOUT 4

(SMOKE +)

Smoke detector power 12 VDC (for those

jurisdictions which allow the Priority zone to be used

with smoke detectors). Current limited to 250 mA

when output is positive and 250 uA when output is

negative. This output defaults to Smoke Power, but

can be reconfigured. Zone 7 may be used for a 2-

wire smoke detector using a 680 ohm EOL resistor.

A

UXOUT 1 to

3

Connect negative lead of low current device [relay,

LED (install 1kohm resistor in series with LED), etc.]

Connect positive lead of device to COM. Current is

limited to 50 mA when output is negative, and 250

uA when output is positive.

Module list

Table 3 shows the modules that are compatible with the NX-

6V2 system. Additional information and a catalog listing all

system components is available from UTC Fire & Security

Customer Support.

Table 3 Modules that can be added to the NX-6V2

Part Description

NX-108E 8-zone LED keypad

NX-116E 16-zone LED keypad

NX-124E 24-zone LED keypad

NX-148E Alphanumeric 48-zone LCD keypad

NX-148E-RF Alphanumeric 48-zone LCD keypad with built-in 48-

zone wireless receiver

NX-200 Zone doubling kit (includes one hundred 3.74k and

one hundred 6.98k resistors)

NX-320E Smart power supply and bus extender

NX-408E 8-zone wireless expansion module

(UL listed part #60-904)

NX-416E 16-zone wireless expansion module

(UL listed part #60-904)

NX-448E 48-zone wireless expansion module

(UL listed part #60-904)

NX-508E Eight-output module

NX-534E Two-way listen-in module

NX-540E Operator telephone interface module

NX-548E 48-zone wireless receiver

NX-591E-

GSM

Cell interface

NX-1192E 192-zone LCD keypad

NX-1208E 8-zone LED keypad

NX-1248E 48-zone LCD keypad

NX-1308E 8-zone LED door design keypad

NX-1316E 16-zone LED door design keypad

NX-1324E 24-zone LED door design keypad

NX-1448E 48-zone fixed language icon keypad

[1] These products have not been tested and approved by

Underwriters Laboratories, In.

[2] These wireless devices are UL listed only for residential

applications.

Note: The NX-6V2 control panel sends a trouble condition once each

hour if it senses that no devices have been enrolled. This report

shows expander trouble--device zero (0).

Control panel programming

Programming the control panel requires you to enter program

mode, select the module to program, program a location, and

then exit the location and program mode.

Enter program mode

To enter program mode, do the following:

1. Press 8. The five function LEDs (Stay, Chime, Exit,

Bypass, and Cancel) begin flashing.

2. Enter the go to program code (default is 9, 7, 1, 3). If the

go to program code entry is valid, the Service LED flashes,

and the five function LEDs illuminate. You are now in

program mode and can select the module to program.

Select the module to program

Since all modules connected to the NX-6V2 are programmed

through the keypad, the module you are programming should

be the first entry. To select the module to program, enter 0, #.

The 0 is the module number of the control, and # is the entry

key. You can find other module entry numbers in the module

documentation.

Program a location

Once you enter the module number, the Armed LED

illuminates, indicating the keypad is waiting for you to enter a

programming location. To program a location, do the following:

1. To access any location, enter the desired programming

location, followed by #. If the location is a valid location,

the Armed LED extinguishes, the Ready LED illuminates,

and the binary data for the first segment of the location is

shown by the Zone LEDs.

2. While entering new data, the Ready LED begins flashing

to indicate a data change in process.

2 NX-6V2 Control Panel Installation Instructions

3. Press  to store the newly entered data. The keypad

advances to the next segment and displays its data.

Repeat this procedure until the last segment is reached.

4. To move to another location after exiting a location (Armed

LED illuminated):

• Press the Police key for the next sequential location.

• Press the Fire key for the previous location.

• Press the Medical key for the same location.

5. To review the data in a specific location, repeat the above

procedure, pressing  but with no numeric data entry.

Each time you press , the programming data of the next

segment displays.

Exit a location

To exit the current programming location, do the following:

1. Press the  key. The Ready LED goes off and the Armed

LED goes on. You must press the key to save the data.

2. To exit before the last segment, press # (Armed LED

illuminates).

You are now ready to enter another programming location. If

you attempt to program an invalid entry for a particular

segment, the keypad beeps three times indicating an error and

remains in that segment awaiting a valid entry.

Exit program mode

To exit program mode, do the following:

1. When you have completed all programming, press Exit to

leave the selected module.

2. If there is another module to be programmed, select it by

entering its address, followed by #. The procedure for

programming these devices is the same as for the control

panel, except the locations are for the module selected.

3. If no additional modules are to be programmed, press Exit

again to leave program mode.

Loading factory defaults

To load factory defaults, enter program mode, enter the device

address and number and then enter 9, 1, 0, #. The keypad

beeps three times indicating that loading is in progress. The

process takes about six seconds. You cannot exit the location

until loading is completed.

Enrolling modules and keypads

The NX-6V2 automatically finds and stores all keypads, zone

expanders, wireless receivers, and other modules connected

to the data terminal into the NX-6V2 memory. This allows the

modules to be supervised by the control panel.

To enroll the modules, do the following:

1. Enter program mode and program the desired settings for

each module.

2. When you exit program mode, the NX-6V2 automatically

enrolls the devices. The enrolling process takes about 12

seconds, during which time the Service LED illuminates. If

a speaker is attached to the NX-6V2, it clicks at this time.

If a siren or bell is attached to the NX-6V2, it sounds for

about one second. If the module is not detected, the

Service LED illuminates.

Note: User codes are not accepted during the enrolling

process.

Quick start programming locations

For most routine installations, the quick start locations allow

you to enable a majority of the options available with the NX-

6V2 (when communicating in Contact ID or SIA formats). The

quick start locations include:

• Location 0 - Phone 1

• Location 1 - Phone 1 account code

• Location 2 - Phone 1 communicator format

• Location 3 - Phone 1 dial attempts/backup control

Location 0 - Phone 1

Location 0 has 20 segments of numerical data. Use this

location to program phone 1. The default for each segment is

14.

• To program a delay of four seconds, enter 13 in the

appropriate segment.

• To program tone dialing, enter 15 in the segment where

tone dialing begins.

• If the entire number is tone dialing, enter 15 in the first

segment.

• Enter 11 for a *, and 12 for a #.

Location 2 - Phone 1 communicator format

Location 2 has one segment of numerical data. Use this

location to program the communicator format used to transmit

to the receiver connected to phone 1. Refer to your central

station receiver documentation to determine which format is

compatible. Table 4 describes the formats for this location. If

you need a format other than those listed, review the override

options described in Loc to build the appropriate format.

Program a 15 to create a special format (in addition to the

entries in Location 18). The default is 0. If this location contains

NX-6V2 Control Panel Installation Instructions 3

a 0, the built-in communicator is disabled and the NX-6V2

functions as a local-only control.

Table 4 communicator formats

Data Format Description

0 Local Communicator is disabled

1 Universal 4+2 Two-digit event code 1800 Hz transmit

2300 Hz handshake double round parity

40 pps [1]

2 3+1 fast (or 4+1) One-digit event code 1900 Hz transmit

1400 Hz handshake double round parity

20 pps

3 Reserved Reserved

4 Pager Two-digit event code DTMF

transmission

5 3/1 or 4/1 slow 1800 Hz transmit 2300 Hz handshake

double round parity 20 pps hex

capability

6 3/1 or 4/1 slow 1800 Hz transmit 1400 Hz handshake

double round parity 20 pps hex

capability

7 3/1 or 4/1 fast 1800 Hz transmit 2300 Hz handshake

double round parity 40 pps hex

capability

8 3/1 or 4/1 fast 1800 Hz transmit 1400 Hz handshake

double round parity 40 pps hex

capability

9 3/1 or 4/1 fast with

parity

1800 Hz transmit 2300 Hz handshake

single round parity 40 pps hex capability

10 3/1 or 4/1 fast with

parity

1800 Hz transmit 1400 Hz handshake

single round parity 40 pps hex capability

11 4+2 express Two-digit event code DTMF

transmission

12 4+2 fast Two-digit event code 1900 Hz transmit

1400 Hz handshake double round parity

20 pps

13 Ademco contact ID DTMF

14 SIA Frequency shift keys

15 Custom format See Loc

16 3/1 or 4/1 slow Same as 5, but sends the alarm event

code rather than the zone number

17 3/1 or 4/1 slow Same as 6, but sends the alarm event

code rather than the zone number

18 3/1 or 4/1 fast Same as 7, but sends the alarm event

code rather than the zone number

19 3/1 or 4/1 fast Same as 8, but sends the alarm event

code rather than the zone number

20 3/1 or 4/1 fast with

parity

Same as 9, but sends the alarm event

code rather than the zone number

21 3/1 or 4/1 fast with

parity

Same as 10, but sends the alarm event

code rather than the zone number

22 SIA SIA with area modifiers

[1] pulses per second

Location 3 - Phone 1 dial attempts/backup control

Location 3 has two segments of numerical data.

Segment 1 - Phone 1 dial attempts

Program the number of dial attempts (1 to 15) the

communicator makes to phone 1 before ending the notification

process. The default is 8, which means that the communicator

makes eight attempts to the first number.

Segment 2 - Phone 1 backup control

Program the backup control for phone 1. The default is 0.

• Program a 0 in segment 2 to cause the NX-6V2 to make

the designated number of attempts to phone 2 before

setting the fail to communicate condition to stop reporting.

• Program a 1 in segment 2 to cause the NX-6V2 to stop

trying to communicate after the designated number of

attempts have been made to phone 1.

• Program a 2 in segment 2 to cause the NX-6V2 to make

the dial attempts in increments of two. The first two

attempts are made to phone 1, the next two attempts to

phone 2. This repeats until the total number of attempts

designated in segment 1 is completed.

Location 4 - Phone 1 events reported

Location 4 has two segments of feature selection data. Use

this location to select those events reported to phone 1.

• If you do not want dual or split reporting, use Location 4 to

select all events to phone 1.

• If you want dual or split reporting and the split is based on

the event type (alarm, open/close, etc.), use Location 4 to

select only those events that are reported to phone 1.

• If you don’t want events reported to phone 1, program 0 in

Location 4 (disabling all options).

Segment 1

1. Alarms and alarm restores.

2. Opening and closings.

3. Zone bypass and bypass restores.

4. Zone trouble and trouble restores.

5. Power fail, low battery, power restore, and low battery

restore.

6. Bell cut, telephone line cut, bell cut restore, telephone line

restore.

7. Test reports.

8. Start and end programming, download complete.

4 NX-6V2 Control Panel Installation Instructions

Segment 2

1. Zone and box tamper and tamper restore.

2. Auxiliary power over current, ground fault, and restore for

both.

3. Wireless sensor missing and restore.

4. Wireless sensor low battery and restore.

5. Expander trouble and restore.

6. Fail to communicate.

7. Zone activity monitor.

8. Reserved

Location 18 - Custom communicator format

Location 18 has four segments of feature selection data. Use

this location to program the communicator format used to

transmit to the receiver connected to phone 3. Refer to your

central station receiver documentation to determine which

format is compatible. Select a format from Table 4. If you need

a format other than those listed, review the override options

described in this location to build the appropriate format.

Segment 1

1. On for 1800 Hz transmit; off for 1900 Hz.

2. On for 2300 Hz handshake; off for 1400 Hz.

3. On for cksum parity; off for double round parity.

4. On for two-digit event code; off for one-digit event code.

5. Reserved.

6. Reserved.

7. On for 20 pps; off for 10 or 40 pps.

8. On for 10 pps; off for 20 or 40 pps.

Segment 2

1. On for pager format (no handshake required).

2. On for 1400/2300 handshake.

3. Reserved.

4. Reserved.

5. On for contact ID.

6. On for SIA.

7. On for contact ID or 4+3.

8. On for DTMF.

Segments 3 and 4 - Reserved

Location 25 - Zones 1 to 8 zone type

Location 25 has eight segments of numerical data. Use this

location to program the zone type for zones 1 to 8. Use

segment 1 for zone 1, segment 2 for zone 2, etc. The segment

defaults are 3, 5, 6, 6, 6, 6, 6, 6.

Zones are programmed to be one of thirty different types. Use

zone types 17 through 20 for wireless, or for hardwired zones

using European double EOL configuration

Table 5 describes the zone types.

Table 5. Zones types

Zone Type Description

1. Day zones This zone is instant when the system is armed;

trouble zone when the system is disarmed.

2. 24-hour

audible

This zone creates an instant yelping siren alarm

regardless of the armed state of the control panel.

3. entry/exit

delay

A trip starts entry delay 1. The lack of a trip during

exit delay enables the automatic bypass or instant

mode if programmed.

4. Follower with

autobypass

disabled

This zone is instant when the system is armed and

no entry or exit delays are being timed. It is delayed

1 time during entry and exit. This zone does not

automatically bypass even if enabled in segment 1.

5. Interior

follower with

autobypass

This zone is instant when the system is armed and

no entry or exit delay is being timed. It is delayed 1

time during entry and exit. This zone automatically

bypasses if enabled in segment 1.

6. Instant This zone creates an instant alarm whenever it is

tripped and the armed LED is on.

7. 24-hour

silent

This zone creates an instant silent alarm regardless

of the armed state of the control panel. It does not

display on the keypad.

8. Fire This zone illuminates the fire LED and sounds the

temporal siren each time the zone is shorted. The

fire LED flashes rapidly indicating a problem if the

zone is open.

9. Entry/exit

delay 2

A trip starts entry delay 2. The lack of a trip during

exit delay enables the automatic bypass or instant

mode if programmed.

10. 24-hour

silent

supervised

This zone creates an instant silent alarm regardless

of the armed state of the control panel. It displays

on the keypad.

11. Reserved

12. Interior

follower with

cross zone

This zone is instant when the system is armed and

no entry or exit delay is being timed. It is delayed

during entry and exit delay times. If a cross zone is

not being timed, it starts a cross zone timer. If a cross

zone is being timed, it creates an instant alarm. This

zone automatically bypasses when enabled in

segment 1.

13. Instant

entry guard

This zone creates on instant alarm whenever it is

tripped and the stay LED is off. It starts an entry

delay type 2 if it is tripped, the system is armed,

and the stay LED is on.

NX-6V2 Control Panel Installation Instructions 5

14. Entry/exit

delay 1 with

group bypass

A trip starts entry delay 1. This zone bypasses

when the group bypass command is entered at the

keypad. The lack of a trip during exit delay enables

the automatic bypass or instant mode if

programmed.

15. Interior

follower with

group bypass

This zone is instant when the system is armed and

no entry or exit delays are being timed. It is delayed

during entry/exit delay times. This zone bypasses

when the group bypass command is entered at the

keypad. This zone automatically bypasses if

enabled in segment 1.

16. Instant with

group bypass

This zone creates an instant alarm whenever it is

tripped and the armed LED is on. This zone

bypasses when the group bypass command is

entered at the keypad.

17. Entry/exit

delay 1 with

tamper

A trip starts entry delay 1. The lack of a trip during

exit delay enables the automatic bypass or instant

mode if programmed. This zone type is used to

enable the tamper on a wireless transmitter.

18. Interior

follower with

tamper and

autobypass

This zone is instant when the system is armed and

no entry or exit delay is being timed. It is delayed

during entry and exit delay times. This zone

automatically bypasses if enabled in segment 1.

This zone type is used to enable the tamper on a

wireless transmitter.

19 Instant with

tamper

This zone creates an instant alarm whenever it is

tripped and the armed LED is on. This zone type is

used to enable the tamper on a wireless

transmitter.

20. Entry/exit

delay 2 with

tamper

A trip starts entry delay 2. The lack of a trip during

exit delay enables the automatic bypass or instant

mode if programmed. This zone type is used to

enable the tamper on a wireless transmitter.

21. Gas

detection

This zone creates an instant alarm regardless of

the armed state of the control panel. It displays on

the keypad and activates the keypad sounder.

22. Low

temperature

detection

This zone creates an instant silent alarm regardless

of the armed state of the control panel. It displays

on the keypad and activates the keypad sounder.

23. High

temperature

detection

This zone creates an instant silent alarm regardless

of the armed state of the control panel. It displays

on the keypad and activates the keypad sounder.

24. Manual fire This zone illuminates the fire LED and sounds the

temporal siren each time the zone is shorted. It

also flashes (rapidly) the fire LED, indicating a

problem if the zone is open.

25. Chime only This zone creates no alarm regardless of the

armed state of the control panel. It chimes anytime

it is faulted and displays on the keypad. Local only.

26. Interior

follower delay 2

This zone is instant when the system is armed and

no entry or exit delay is being timed. It is delayed 2

times during entry and exit. This zone automatically

bypasses if enabled in segment 1.

27. Interior

follower force

armable

This zone is instant when the system is armed and

no entry or exit delay is being timed. It is delayed 1

time during entry and exit. This zone automatically

bypasses if enabled in segment 1.

28. Entry/exit

force armable

delay 2

A trip starts entry delay 2. The lack of a trip during

exit delay enables the automatic bypass or instant

mode if programmed.

29. Interior

follower with

activity

supervision

This zone is instant when the system is armed and

no entry or exit delay is being timed. It is delayed

during entry and exit delay times. It sends a report

if the zone activity time is reached without a change

of state. This zone automatically bypasses if

enabled in segment 1.

30. Entry/exit

with activity

supervision

A trip starts entry delay 1. It sends a report if the

zone activity time is reached without a change of

state. The lack of a trip during exit delay enables

the automatic bypass or instant mode if

programmed.

Underwriters laboratories information

The NetworX NX-6V2 holds the following listings from

Underwriters Laboratories (US and Canadian)

UL365 Police station connected burglar alarms.

UL609,

CAN/ULC-S303-

M91

Mercantile, police station connect with basic line

security requires NX-003-C enclosure

UL985,

CAN/ULC-S545-

M89

Household fire

UL1023, ORD-

C1023-1974

Household burglary

UL1610 Central station burglar alarm unit

UL1635 Digital alarm communicator system units

UL1637 Home health care signaling

When installing an NX-6V2 in compliance with Underwriters

Laboratories, the following instructions must be observed:

• Initiating and indicating devices must be rated at 11.5 to

12.4 VDC residential, 12.0 VDC commercial.

• Force arming and auto arming must not be enabled.

• For residential fire applications, the indicating devices

shall be a Wheelock 34T-12 or equivalent.

• The listen in feature shall not be enabled.

• The siren/bell test must be enabled. The auxiliary outputs

controlling the audible device require a minimum cutoff

time of 15 minutes for commercial burglary, four minutes

for residential applications, or 30 minutes for commercial

burglary for Canada.

• For residential fire installations, the dynamic battery test

time cannot exceed four hours.

• Ringback must be enabled on UL commercial burglary

installations.

• On commercial burglary installations, the fire initiating

circuits must not be connected.

• The entry guard feature must be disabled.

• Group bypassing must be disabled.

• Delay before dial seizure must be set to 0.

6 NX-6V2 Control Panel Installation Instructions

• Total current draw from auxiliary power connections at

terminal positions POS, AUX PWR, and SMOKE PWR

must not exceed 400 mA.

• Remote downloading must not be used on UL listed

systems.

• For residential burglary applications, the maximum entry

and exit delay times are 45 and 60 seconds respectively.

The exit delay time must not exceed 60 seconds for

commercial burglar alarm applications.

• The keyswitch option must not be used.

• The telephone line monitor must be enabled.

• The telephone line cut delay must not exceed 90 seconds.

• The 24-hour communicator test transmission is required.

• For 24-hours of standby power using a 7.0 Ah battery, limit

auxiliary power load to 140 mA.

• For 24-hours of standby power using a 17.2 Ah battery,

limit auxiliary power load to 400 mA.

• The silent keypad option must not be enabled.

• UL has only verified compatibility with the following listed

DACRs and formats: Sure-Gard SG-MLR2-DG:

2,9,10,12,13,14; Silent Knight 9000 - 2,12; FBI -

CP220FBI, 13; and Ademco 685: 2,11,12, and 13.

• For burglary installations, cross zoned detectors must

overlap 100 percent in the area of coverage, and similar

coverage areas must be used. For example, interior

protection is cross zoned with interior protection, and so

on.

• Expander trouble must activate the siren.

• For UL 1637, expander trouble must activate the keypad

sounder.

• If the late to close/early to open feature is enabled, the

opening and closing reports must be enabled.

• For Canadian installations, the class II transformer secure

tab must not be employed.

• The four-wire smoke detector employed must be rated to

operate over the voltage range of 11.5 to 12.4 V.

• Compatible listed devices: (special applications):

• Bell output (sirens): Wheelock models: NS-1215W,

NS- 121575W, NS4-1215W, NS4-121575W, AS-1215W,

AS- 121575W

• Horn/strobe system sensor: S1224MC strobe series;

1224MC Horn/strobe series; H12/24 Horn series

• Smoke output (four-wire detectors): ESL: 500N

series; 449CTE series; 521 series; 541 series

• System sensor models: 2112/24R; 2112/24TR;

2112/24AT; 2112/ATR; 2112/24AITR; 4WTA-B;

4WTR-B; 4WTAR-B; 4WITAR-B

• Detection systems: F220-B6C; D273 series; Hochiki:

SBC- 4/12, 4/12W

Additional UL 609 installation requirements

The alarm housing for a mercantile alarm system without a

remote alarm transmission connection shall be mounted on the

outside of the building, visible from a public street or highway.

It shall be accessible for examination and repair. It shall also

be located not more than four stories above the street level

unless:

a) A second alarm sounding device and housing, intended for

outside service is mounted adjacent to the premises or area of

the building in which the alarm system is installed or

b) A second alarm sounding device, intended for inside service

is mounted within the premises.

In either case, the outside alarm sounding device and housing

may be mounted as high as the seventh floor.

Additional UL 365 installation requirements

In a mercantile burglar alarm system, a mercantile alarm

sounding device located within a building, but outside the

protected area, is acceptable, provided it is rated for outside

service and alarm conditions are transmitted to:

a) The dispatch location of the law enforcement agency having

jurisdiction over the protected property or

b) A central station or residential monitoring station complying

with the Standard for Central-Station Alarm Services, UL 827.

In a mercantile burglar alarm system, an alarm sounding

device located within the area of greatest protection, or outside

the area of greatest protection but within an area protected by

an alarm system and that shares a common control unit with

the system installed in the area of greatest protection, is

acceptable provided it is rated for inside service and alarm

conditions are transmitted to:

a) The dispatch location of the law enforcement agency having

jurisdiction over the protected property or

b) A central station or residential monitoring station complying

with the Standard for Central-Station Alarm Services, UL 827.

An inside sounding device shall be mounted at least 10 feet

(3.05 m) above the floor or at the surface of the ceiling. When

there is fixed construction within the area that could provide

access for an intruder, the alarm sounding device shall also be

mounted at least 4 feet (1.2 m), as measured horizontally,

away from the edges of the fixed construction or at least 10

feet (3.05 m) above it so as to minimize access by an intruder.

NX-6V2 Control Panel Installation Instructions 7

WARNING: Electrical codes will vary, depending on the

country and city where the system is installed. It is the

installers responsibility to ensure that the electrical installation

is safe and conforms to all applicable codes , laws, and

regulations. Only qualified persons should connect this device

to the main supply.

Minimum system configurations for UL installations

The following requirements apply to residential fire, residential

burglary, and commercial burglary installations.

• The NetworX NX-6V2 panel is necessary to initiate

residential and commercial installations.

• At least one compatible keypad is needed for all

applications.

• The AD10-12 bell and UL Approved bell-housing shall be

used for all applications.

• Commercial UL applications require the NX-003-C metal

enclosure. Supplied screws to be used.

• A minimum of two keypads is required for home health

applications, and each keypad must be set to a unique

address.

• The wireless devices are only UL listed for residential

applications.

• The DACT shall be enabled for all commercial burglary

applications.

UL requires that an alarm panel work for a minimum amount of

time during a power failure. Table 6 lists the battery capacities

needed to meet time limits based on the current draw of the

panel and all attached devices.

Table 6. Battery capacities

Standby time Total

auxiliary

current

Standby

battery

capacity

Alarm current

24-Hours 1.9 A

1.25 A

600 mA

51 Ah

34 Ah

17 Ah

600 mA

1 A

1 A

48-Hours 900 mA

600 mA

300 mA

51 Ah

34 Ah

17 Ah

1 A

1 A

1 A

72-Hours 600 mA

400 mA

200 mA

51 Ah

34 Ah

17 Ah

1 A

1 A

1A

Note: Calculations are based on three 17A batteries.

WARNING: Replace only with a Panasonic LC12V4BP or

Yuasa NP4-12 battery. There is a risk of explosion if the

battery is replaced with an incorrect type.

WARNING: If separate power supplies are necessary to

accommodate additional devices, safety standards require that

each power supply be prominently marked with adequate

instructions for removing all power from the unit.

Caution: Observe polarity when installing a new battery.

Installing the battery backwards may cause damage to the

panel. Dispose of used batteries according to the

manufacturer’s instructions and/or local government

authorities.

Specifications

Operating power 16.5 VAC 40 or 50 VA transformer

Auxiliary power w/25

VA transformer

12 VDC regulated 500 mA

Auxiliary power w/40 ro

50 VA transformer (M

G Electronics part

number 22-156 for UL

or 22-156-CN for

Canadian installations)

12 VDC regulated 1 A

Loop resistance

Standard loop

300 ohms maximum

Fuse Type T 200 mA 250 VAC

Built-in siren driver Two tone (temporal and yelp)

Loop response Selectable 50 mS or 500 mS

Operating temperature 32 to 120°F (0 to 49°C)

LED keypad

• Current draw

• Zones normal w/o

sounder

• Dimensions

• 130 mA max.

• 55 mA

• 6.4 x 4.0 x 1.1 in. (16.3 x 10.2 x 2.8 cm)

LED keypad

• Current draw

• Zones normal w/o

sounder

• Dimensions

• 110 mA max.

• 75 mA

• 6.4 x 5.3 x 1.0 in. (16.3 x 13.5 x 2.5 cm)

Metal enclosure

dimension

11.25 x 11.25 x 3.50 in. (28.58 x 28.58 x 8.90

cm)

Shipping weight 9 lb. (4.1 kg)

8 NX-6V2 Control Panel Installation Instructions

Regulatory information Contact information

FCC compliance This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference that

may cause undesired operation.

Complies with Part 68 FCC Rules.

ACTA (FCC) ID: GCQUSA-33408-AL-E

IC: 1175A-NXV2

2002/96/EC (WEEE directive): Products marked

with this symbol cannot be disposed of as

unsorted municipal waste in the European Union.

For proper recycling, return this product to your

local supplier upon the purchase of equivalent

new equipment, or dispose of it at designated

collection points. For more information see:

www.recyclethis.info.

For contact information, see www.utcfireandsecurity.com or

www.interlogix.com.

For technical support, Toll-free: 888.437.3287 in the US

including Alaska, Hawaii, Puerto Rico, and Canada. Outside

the tool-free area: Contact your dealer.

Copyright © 2011 UTC Fire & Security. All rights reserved.

ANSI/SIA CP-01 requirements

CP-01 feature descriptions and specifications are listed in Table 7. The following are requirements for compliance with ANSI/SIA

CP-01 standards.

Note: Where a conflict exists, UL requirements take precedence over ANSI/SIA requirements.

Minimum system requirements:

• One control panel

• Two keypads

Do not enable remote arming in SIA classified installations.

Off premise transmission must be in the SIA format.

Do not exceed 1 minute for the abort window and entry delay.

Note: A call-waiting cancel on a noncall-waiting line prevents successful connection to the central station

Table 7. CP-01 feature descriptions and specifications

CP-01 feature description Feature description as

shown in manual Progra

m

location

Seg/op

t Default CP-01 required setting

Exit 1 delay 24 2 60 45 to 240 seconds Exit time

Exit 2 delay 24 4 60 45 to 240 seconds

Progress annunciation /

disable for silent exit <1>

Silent keypad option 93 2 All

annunciators

enabled

Allowed (individual keypads may be disabled)

Exit time restart (reexit) This feature is not programmable in the panel. Enabled

A

uto stay arm on unvacated

premises

Auto bypass 23 1/3 Enabled Enabled

Exit time and progress

annunciation/disable for

remote arm

This feature is not programmable in the panel. Exit time and

progress are always enabled.

Enabled (disabled for remote arming)

Exit 1 delay 24 1 30 30 to 240 seconds Entry delays <2>

Exit 2 delay 24 3 30 30 to 240 seconds

A

bort window - for

nonfire zones

Dialer delay 40 8 30 Enabled (may be disabled by zone/zone type,

but no cancel reports will be sent)

A

bort window time - for

nonfire zones <2>

Dialer delay 40 8 30 15 to 45 seconds

NX-6V2 Control Panel Installation Instructions 9

A

bort annunciation This feature is not programmable in the panel. Flashing cancel

LED goes off when disarming.

Enabled

Cancel annunciation Cancel 23 3/6 Enabled Enabled

Duress feature Duress 44 Disabled Disabled

Two trips on cross zone 37 5/4 Disabled Required

Keypad sounds on cross

zone trip

39 5 Disabled

Cross zoning

Zone type characteristic 111 3/4 Disabled

Programmable cross zoning

time

Cross zone time 40 6 5 minutes Allowed

Swinger shutdown Swinger shutdown count 38 n/a Enabled for 1

trip

For all non fire zones. Shut down at 1 to 2 trips.

Swinger shutdown disable Swinger shutdown count 38 n/a Enabled for 1

trip

Allowed

Fire alarm verification Fire alarm verification time 40 9 Disabled Required (depends on panel and sensors)

Call waiting cancel Must be programmed as

part of the phone number

0 n/a n/a Required (depends on user phone line)

Recent closing 23 3/7 Enabled

Exit error 23 3/8 Enabled

Default changes (from prior

versions):

Power delay 40 3 60 seconds

<1> Refer to your keypad installation manual.

<2> Combined abort window time and entry delay must not exceed one minute.

10 NX-6V2 Control Panel Installation Instructions