NS3500 24T 4C Managed Switch Command Guide 1073459a En

: Interlogix 1073459A-Ns3500-24T-4C-Command-Guide-En 1073459a-ns3500-24t-4c-command-guide-en library

Open the PDF directly: View PDF .
Page Count: 326

Download
Open PDF In Browser	View PDF

NS3500-24T-4C Managed
Switch Command Guide

P/N 1073459-EN • REV A • ISS 06MAR18

Copyright

Trademarks and patents
Manufacturer

Version

© 2018 United Technologies Corporation.
Interlogix is part of UTC Climate, Controls & Security, a unit of United Technologies
Corporation. All rights reserved.
Trade names used in this document may be trademarks or registered trademarks of the
manufacturers or vendors of the respective products.
Interlogix
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
This document applies to NS3500-24T-4C.

FCC compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

FCC compliance

Class A: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.

Canada

This Class A digital apparatus complies with CAN ICES-003 (A)/NMB-3 (A).
Cet appareil numérique de la classe A est conforme à la norme CAN ICES-003
(A)/NMB-3 (A).

ACMA compliance

Notice! This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate measures.

Certification

EU directives

This product and - if applicable - the supplied accessories too are marked with "CE" and
comply therefore with the applicable harmonized European standards listed under the
EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of
as unsorted municipal waste in the European Union. For proper recycling, return this
product to your local supplier upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information see:
www.recyclethis.info.

Product warnings and
disclaimers

THESE PRODUCTS ARE INTENDED FOR SALE TO AND INSTALLATION BY
QUALIFIED PROFESSIONALS. UTC FIRE & SECURITY CANNOT PROVIDE ANY
ASSURANCE THAT ANY PERSON OR ENTITY BUYING ITS PRODUCTS,
INCLUDING ANY “AUTHORIZED DEALER” OR “AUTHORIZED RESELLER”, IS
PROPERLY TRAINED OR EXPERIENCED TO CORRECTLY INSTALL FIRE AND
SECURITY RELATED PRODUCTS.
For more information on warranty disclaimers and product safety information, please
check www.firesecurityproducts.com/policy/product-warning/ or scan the QR code:

Contact information and
manuals

For contact information go to: www.interlogix.com or www.firesecurityproducts.com.
To get translations for this and other product manuals go to:
www.firesecurityproducts.com.

Content
Chapter 1

Command line interface 2
Accessing the CLI 2
Command line modes 2
Requirements 4

Chapter 2

Console CLI management 5
Terminal setup 5
Log on to the console 6
Configuring the IP address 7

Chapter 3

Telnet CLI management 10
Telnet login 10

Chapter 4

Commands for CLI configuration 11
clear 11
configure terminal 29
copy 241
debug 241
delete 242
dir 242
disable 243
do 243
dot1x 244
enable 244
erps 245
exit 245
firmware 246
ip 247
logout 247
more 248
no 248
ping 249
reload 250
send 251
show 252
terminal 322

NS3500-24T-4C Managed Switch Command Guide

1

Chapter 1
Command line interface
Accessing the CLI
When accessing the management interface for the switch over a direct connection to
the server’s console port or via a Telnet connection, the switch can be managed by
entering command keywords and parameters at the prompt. Using the switch's
command-line interface (CLI) is very similar to entering commands on a UNIX system.
This chapter describes how to use the Command Line Interface (CLI).

Command line modes
The CLI groups all the commands in appropriate modes according to the nature of the
command. A sample of the CLI command modes are described below. Each of the
command modes supports specific software commands.

Mode-based command hierarchy
The Command Line Interface (CLI) groups all the commands in appropriate modes by
the nature of the commands. Examples of the CLI command modes are described
below. Each of the command modes supports specific switch commands.
The CLI Command Modes table captures the command modes, the prompts visible in
that mode, and the exit method from that mode.
Command Mode

Access Method

Prompt

Exit or Access Previous
Mode

User mode

This is the first level of
access. Perform basic
tasks and list system
information.

COMMAND>

Enter Logout command

Priveleged mode

From the User Mode, enter
the enable command.

Switch#

To exit to the User Mode,
enter exit or Logout.

Global config mode

From the Privileged Mode,
enter the configuration
command.

Switch (Config)#

To exit to the Privileged
Mode, enter the exit
command.

2

NS3500-24T-4C Managed Switch Command Guide

Chapter 1: Command line interface

Command Mode

Access Method

Prompt

Exit or Access Previous
Mode

Interface config mode

From the Global Config
mode, enter the interface
 command.

Switch (interface
)#

To exit to the Global
Config mode, enter exit.

The CLI is divided into various modes. The commands in one mode are not available
until the operator switches to that particular mode. The commands available to the
operator at any point in time depend upon the mode. Entering a question mark (?) at
the CLI prompt displays a list of the available commands and descriptions of the
commands.
The CLI provides the following modes:

User mode
When the operator logs into the CLI, the User Mode is the initial mode. The User Mode
contains a limited set of commands. The command prompt shown at this level is:
Command Prompt: switch>

Privileged mode
To have access to the full suite of commands, the operator must enter the Privileged
Mode. The Privileged Mode requires password authentication. From Privileged Mode,
the operator can issue any Exec command to enter the Global Configuration mode. The
command prompt shown at this level is:
Command Prompt: switch#

Global config mode
This mode permits the operator to make modifications to the running configuration.
General setup commands are grouped in this mode. From the Global Configuration
mode, the operator can enter the Interface Configuration mode. The command prompt
at this level is:
Command prompt: switch(Config)#
From the Global Config mode, the operator may enter the following configuration
modes:
Interface config mode
Many features are enabled for a particular interface. The Interface commands enable or
modify the operation of an interface. In this mode, a physical port is set up for a specific
logical connection operation. The command prompt at this level is:
Command prompt: Switch(Interface )#

NS3500-24T-4C Managed Switch Command Guide

3

Chapter 1: Command line interface

Requirements
•

Workstations running Windows XP/Vista/7/8/10, Windows 2003/2008, MAC OS X or
later, Linux, UNIX, or other platforms are compatible with TCP/IP protocols.

•

Workstations are installed with Ethernet NIC (Network Interface Card).

•

Serial Port Connection (Terminal)

•

4

•

The above Workstations come with COM Port (DB9) or USB-to-RS-232
converter.

•

The above Workstations have been installed with terminal emulator, such as
Hyper Terminal included in Windows XP/2003.

•

Serial cable -- one end is attached to the RS-232 serial port, while the other end
to the console port of the Managed Switch.

Ethernet Port Connection
•

Network cables -- Use standard network (UTP) cables with RJ-45 connectors.

•

The above PC is installed with Web Browser and JAVA runtime environment
plug-in.

NS3500-24T-4C Managed Switch Command Guide

Chapter 2
Console CLI management
Terminal setup
To configure the system, connect a serial cable to a COM port on a PC or notebook
computer and to a RS232 type of serial port on the managed switch.

A terminal program is required to make the software connection to the managed switch.
Windows' Hyper Terminal program may be a good choice. The Hyper Terminal can be
accessed from the Start menu.
1. Click Start > Programs > Accessories, and then click Hyper Terminal.
2. When the following screen appears, make sure that the COM port is configured as
shown:

5

NS3500-24T-4C Managed Switch Command Guide

Chapter 2: Console CLI management

If required, you can change these settings after logging on. This management method
is often preferred because you can remain connected and monitor the system during
system reboots. Also, certain error messages are sent to the serial port, regardless of
the interface through which the associated action was initiated. A Macintosh or PC
attachment can use any terminal-emulation program for connecting to the terminal
serial port. A workstation attachment under UNIX can use an emulator such as TIP.

Log on to the console
Once the terminal is connected to the device, power on the managed switch, and the
terminal will display “running testing procedures”. Then, the following message asks to
log-in user name and password. The factory default user name and password are
shown as follows and the login screen appears.
Username: admin
Password: admin

6

NS3500-24T-4C Managed Switch Command Guide

Chapter 2: Console CLI management

The user can now enter commands to manage the managed switch. For a detailed
description of the commands, refer to the following chapters.
Note:
1. For security purposes, change and memorize the new password after this first
setup.
2. Only accept commands in lowercase letters under the console interface.

Configuring the IP address
The Managed Switch is shipped with the default IP address shown below.
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
To check the current IP address or modify a new IP address for the switch, follow these
procedures:

Show the current IP address
At the “#” prompt, enter “show ip interface brief”. The screen displays the current IP
address and Subnet Mask as shown:

NS3500-24T-4C Managed Switch Command Guide

7

Chapter 2: Console CLI management

Configure the IP address
At the “#” prompt, enter the following command and press Enter.
# configure terminal
(config)# interface vlan 1
(config-if-vlan)# ip address 192.168.1.100 255.255.255.0
The previous command would apply the following settings for the managed switch.
IP Address: 192.168.1.100
Subnet Mask: 255.255.255.0

At the “#” prompt, enter “show ip interface brief” to check if the IP address has
changed.

8

NS3500-24T-4C Managed Switch Command Guide

Chapter 2: Console CLI management

Store the current switch configuration
At the “#” prompt, enter the following command and press Enter.
# copy running-config startup-config

If the IP is successfully configured, the managed switch will apply the new IP address
setting immediately. You can access the web interface of the managed switch through
the new IP address.
Note: If you are not familiar with the console command or the related parameter, enter “
?” at any time in the console to get the help description.

.

NS3500-24T-4C Managed Switch Command Guide

9

Chapter 3
Telnet CLI management
Telnet login
The managed switch also supports telnet for remote management. The switch asks for
a user name and password for remote login when using telnet. Use “admin” for the
both the username and password.
Default IP address: 192.168.0.100
Username: admin
Password: admin

NS3500-24T-4C Managed Switch Command Guide

10

Chapter 4
Commands for CLI
configuration
clear
clear access management statistics
Command:
clear access management statistics
Default:
N/A
Usage Guide:
To clear the access management statistics.
Example:
To clear the Switch’s access management statistics.
Switch# clear access management statistics

clear access-list ace statistics
Command:
clear access-list ace statistics
Default:
N/A
Usage Guide:
To clear the Access list entry statistics.
Example:
To clear the Switch’s Access list entry statistics.
Switch# clear access-list ace statistics

NS3500-24T-4C Managed Switch Command Guide

11

Chapter 4: Commands for CLI configuration

clear dot1x statistics interface
Command:
clear dot1x statistics interface GigabitEthernet |
10GigabitEthernet
Default:
N/A
Usage Guide:
To clear the dot1x statistics.
Example:
To clear the Switch’s GigabitEthernet 1/25 dot1x statistics.
Switch# clear dot1x statistics interface GigabitEthernet 1/25

clear eps
Command:
clear eps 


The EPS instance number.

Default:
N/A
Usage Guide:
To clear the EPS instance number.

clear erps
Command:
clear erps < ERPS group numbers > statistics
Default:
N/A
Usage Guide:
To clear the ERPS group numbers statistics.
Example:
To clear the Switch’s ERPS group 1 statistics.
Switch# # clear erps 1 statistics

clear erps statistics
Command:
clear erps statistics

12

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Default:
N/A
Usage Guide:
To clear the ERPS statistics.
Example:
To clear the Switch’s ERPS statistics.
Switch# clear erps statistics

clear evc statistics
Command:
clear evc statistics
Default:
N/A
Usage Guide:
To clear the Ethernet Virtual Connections statistics.
Example:
To clear the Switch’s Ethernet Virtual Connections statistics.
Switch# clear evc statistics

clear ip arp
Command:
clear ip arp
Default:
N/A
Usage Guide:
To clear the ARP cache.
Example:
To clear the Switch’s ARP cache.
Switch# clear ip arp

clear ip dhcp detailed statistics all
Command:
clear ip dhcp detailed statistics all
Default:
N/A
Usage Guide:

NS3500-24T-4C Managed Switch Command Guide

13

Chapter 4: Commands for CLI configuration

To clear the DHCP detailed statistics for all.
Example:
To clear the Switch’s DHCP detailed statistics for all.
Switch# clear ip dhcp detailed statistics all

clear ip dhcp detailed statistics client
Command:
clear ip dhcp detailed statistics client
Default:
N/A
Usage Guide:
To clear the DHCP client statistics.
Example:
To clear the Switch’s DHCP client statistics.
Switch# clear ip dhcp detailed statistics client

clear ip dhcp detailed statistics helper
Command:
clear ip dhcp detailed statistics helper
Default:
N/A
Usage Guide:
To clear the DHCP normal L2 or L3 forward statistics.
Example:
To clear the Switch’s DHCP normal L2 or L3 forward statistics.
Switch# clear ip dhcp detailed statistics helper

clear ip dhcp detailed statistics server
Command:
clear ip dhcp detailed statistics server
Default:
N/A
Usage Guide:
To clear the DHCP server statistics.
Example:
To clear the Switch’s DHCP server statistics.

14

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch# clear ip dhcp detailed statistics server

clear ip dhcp detailed statistics snooping
Command:
clear ip dhcp detailed statistics snooping
Default:
N/A
Usage Guide:
To clear the DHCP snooping statistics.
Example:
To clear the Switch’s DHCP normal L2 or L3 forward statistics.
Switch# clear ip dhcp detailed statistics snooping

clear ip dhcp relay statistics
Command:
clear ip dhcp relay statistics
Default:
N/A
Usage Guide:
To clear the DHCP relay statistics.
Example:
To clear the Switch’s DHCP relay statistics.
Switch# clear ip dhcp relay statistics

clear ip dhcp server binding
Command:
clear ip dhcp server binding 
 A.B.C.D
Default:
N/A
Usage Guide:
To clear the DHCP server binding cache.
Example:
To clear the Switch’s DHCP server(192.168.0.100) binding cache.

NS3500-24T-4C Managed Switch Command Guide

15

Chapter 4: Commands for CLI configuration

Switch# clear ip dhcp server binding 192.168.0.100

clear ip dhcp server binding automatic
Command:
clear ip dhcp server binding automatic
Default:
N/A
Usage Guide:
To clear the DHCP automatic bindings cache.
Example:
To clear the Switch’s DHCP automatic bindings cache.
Switch# clear ip dhcp server binding automatic

clear ip dhcp server binding expired
Command:
clear ip dhcp server binding expired
Default:
N/A
Usage Guide:
To clear the DHCP expired bindings for free.
Example:
To clear the Switch’s DHCP expired bindings for free.
Switch# clear ip dhcp server binding expired

clear ip dhcp server binding manual
Command:
clear ip dhcp server binding manual
Default:
N/A
Usage Guide:
To clear the DHCP server manual binding cache.
Example:
To clear the Switch’s DHCP server manual binding cache.
Switch# clear ip dhcp server binding manual

16

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

clear ip igmp snooping statistics
Command:
clear ip igmp snooping statistics
Default:
N/A
Usage Guide:
To clear the IGMP snooping statistics.
Example:
To clear the Switch’s IGMP snooping statistics.
Switch# clear ip igmp snooping statistics

clear ip igmp snooping vlan
Command:
clear ip igmp snooping vlan < vlan_list> statistics


VLAN identifier(s): VID

Default:
N/A
Usage Guide:
To clear the IGMP snooping vlan < vlan_list> statistics.
Example:
To clear the Switch’s IGMP snooping vlan 1 statistics.
Switch# clear ip igmp snooping vlan 1 statistics

clear ip statistics icmp icmp-msg
Command:
clear ip statistics icmp icmp-msg 


ICMP message type ranges from 0 to 255

Default:
N/A
Usage Guide:
To clear the IPv4 ICMP traffic for designated message type.
Example:
To clear the Switch’s IPv4 ICMP traffic for designated message type 0.
Switch# clear ip statistics icmp icmp-msg 0

NS3500-24T-4C Managed Switch Command Guide

17

Chapter 4: Commands for CLI configuration

clear ip statistics icmp interface vlan
Command:
clear ip statistics icmp interface vlan 


VLAN identifier(s): VID

Default:
N/A
Usage Guide:
To clear the IPv4 interface/ICMP statistics for specific VLAN.
Example:
To clear the Switch’s IP interface/ICMP statistics for specific VLAN 1.
Switch# clear ip statistics icmp interface vlan 1

clear ip statistics system icmp icmp-msg
Command:
clear ip statistics system icmp icmp-msg 


ICMP message type ranges from 0 to 255

Default:
N/A
Usage Guide:
To clear the IPv4 ICMP statistics for specific ICMP message type.
Example:
To clear the Switch’s IPv4 ICMP statistics for specific ICMP message type 0.
Switch# clear ip statistics system icmp icmp-msg 0

clear ip statistics system icmp interface vlan
Command:
clear ip statistics system icmp interface vlan


VLAN identifier(s): VID

Default:
N/A
Usage Guide:
To clear the IPv4 ICMP interface statistics for specific VLAN.
Example:
To clear the Switch’s IPv4 ICMP interface statistics for specific VLAN 1.
Switch# clear ip statistics system icmp interface vlan 1

18

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

clear ipv6 mld snooping statistics
Command:
clear ipv6 mld snooping statistics
Default:
N/A
Usage Guide:
To clear the ipv6 mld snooping statistics.
Example:
To clear the Switch’s ipv6 mld snooping statistics.
Switch# clear ipv6 mld snooping statistics

clear ipv6 mld snooping vlan
Command:
clear ipv6 mld snooping vlan  statistics


VLAN identifier(s): VID

Default:
N/A
Usage Guide:
To clear the ipv6 mld snooping statistics for specific VLAN.
Example:
To clear the Switch’s ipv6 mld snooping statistics for specific VLAN 1.
Switch# clear ipv6 mld snooping vlan 1 statistics

clear ipv6 neighbors
Command:
clear ipv6 neighbors
Default:
N/A
Usage Guide:
To clear the ipv6 neighbors.
Example:
To clear the Switch’s ipv6 neighbors.
Switch# clear ipv6 neighbors

NS3500-24T-4C Managed Switch Command Guide

19

Chapter 4: Commands for CLI configuration

clear ipv6 statistics icmp icmp-msg
Command:
clear ipv6 statistics icmp icmp-msg 


ICMP message type ranges from 0 to 255

Default:
N/A
Usage Guide:
To clear the IPv6 ICMP traffic for designated message type.
Example:
To clear the Switch’s IPv6 ICMP traffic for designated message type 0.
Switch# clear ipv6 statistics icmp icmp-msg 0

clear ipv6 statistics icmp interface vlan
Command:
clear ipv6 statistics icmp interface vlan 


VLAN identifier(s): VID

Default:
N/A
Usage Guide:
To clear the IPv6 interface/ICMP statistics for specific VLAN.
Example:
To clear the Switch’s IPv6 interface/ICMP statistics for specific VLAN 1.
Switch# clear ipv6 statistics icmp interface vlan 1

clear ipv6 statistics system icmp icmp-msg
Command:
clear ipv6 statistics system icmp icmp-msg 


ICMP message type ranges from 0 to 255

Default:
N/A
Usage Guide:
To clear the IPv6 ICMP statistics for specific ICMP message type.
Example:
To clear the Switch’s IPv6 ICMP statistics for specific ICMP message type 0.
Switch# clear ipv6 statistics system icmp icmp-msg 0

20

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

clear ipv6 statistics system icmp interface vlan
Command:
clear ipv6 statistics system icmp interface vlan


VLAN identifier(s): VID

Default:
N/A
Usage Guide:
To clear the IPv6 ICMP interface statistics for specific VLAN.
Example:
To clear the Switch’s IPv6 ICMP interface statistics for specific VLAN 1.
Switch# clear ipv6 statistics system icmp interface vlan 1

clear lacp statistics
Command:
clear lacp statistics
Default:
N/A
Usage Guide:
To clear the lacp statistics.
Example:
To clear the Switch’s lacp statistics.
Switch# clear lacp statistics

clear lldp statistics
Command:
clear lldp statistics
Default:
N/A
Usage Guide:
To clear the lldp statistics.
Example:
To clear the Switch’s lldp statistics.
Switch# clear lldp statistics

NS3500-24T-4C Managed Switch Command Guide

21

Chapter 4: Commands for CLI configuration

clear logging error info
Command:
clear logging error info
Default:
N/A
Usage Guide:
To clear the logging error info.
Example:
To clear the Switch’s logging error info.
Switch# clear logging error info

clear logging error warning
Command:
clear logging error warning
Default:
N/A
Usage Guide:
To clear the logging error warning.
Example:
To clear the Switch’s logging error warning.
Switch# clear logging error warning

clear logging info error
Command:
clear logging info error
Default:
N/A
Usage Guide:
To clear the logging info error.
Example:
To clear the Switch’s logging info error.
Switch# clear logging info error

22

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

clear logging info warning
Command:
clear logging info warning
Default:
N/A
Usage Guide:
To clear the logging info warning.
Example:
To clear the Switch’s logging info warning.
Switch# clear logging info warning

clear logging warning error
Command:
clear logging warning error
Default:
N/A
Usage Guide:
To clear the logging warning error.
Example:
To clear the Switch’s logging warning error.
Switch# clear logging warning error

clear logging warning info
Command:
clear logging warning info
Default:
N/A
Usage Guide:
To clear the logging warning info.
Example:
To clear the Switch’s logging warning info.
Switch# clear logging warning info

NS3500-24T-4C Managed Switch Command Guide

23

Chapter 4: Commands for CLI configuration

clear mac address-table
Command:
clear mac address-table
Default:
N/A
Usage Guide:
To clear the mac address-table.
Example:
To clear the Switch’s mac address-table.
Switch# clear mac address-table

clear mep
Command:
clear mep 


The MEP instance.

Default:
N/A
Usage Guide:
To clear the MEP instance profiles.

clear mvr name
Command:
clear mvr name 


MVR multicast VLAN name

Default:
N/A
Usage Guide:
To clear the mvr name profiles.

clear mvr statistics
Command:
clear mvr statistics
Default:
N/A
Usage Guide:
To clear the mvr statistics.
Example:
To clear the Switch’s mvr statistics.

24

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch# clear mvr statistics

clear mvr vlan
Command:
clear mvr vlan  statistics


MVR multicast VLAN list

Default:
N/A
Usage Guide:
To clear the mvr vlan statistics for specific VLAN.
Example:
To clear the Switch’s mvr vlan statistics for specific VLAN 1.
Switch# clear mvr vlan 1 statistics

clear network-clock clk-source
Command:
clear network-clock clk-source 


Clock source number

Default:
N/A
Usage Guide:
To clear the ERPS WTR timer for a specific profile.
Example:
To clear the Switch’s ERPS WTR timer for a specific profile 1.
Switch# clear network-clock clk-source 1

clear spanning-tree detected-protocols interface *
Command:
clear spanning-tree detected-protocols interface *
Default:
N/A
Usage Guide:
To clear the spanning-tree detected-protocols for all.
Example:
To clear the Switch’s spanning-tree detected-protocols for all.

NS3500-24T-4C Managed Switch Command Guide

25

Chapter 4: Commands for CLI configuration

Switch# clear spanning-tree detected-protocols interface *

clear spanning-tree detected-protocols interface *
Command:
clear spanning-tree detected-protocols interface *
Default:
N/A
Usage Guide:
To clear the spanning-tree detected-protocols for all.
Example:
To clear the Switch’s spanning-tree detected-protocols for all.
Switch# clear spanning-tree detected-protocols interface *

clear spanning-tree detected-protocols interface
GigabitEthernet
Command:
clear spanning-tree detected-protocols interface
GigabitEthernet 
 Port list in X/X-XX
Default:
N/A
Usage Guide:
To clear the spanning-tree detected-protocols for specific GigabitEthernet port.
Example:
To clear the Switch’s spanning-tree detected-protocols for specific GigabitEthernet
1/1.
Switch# clear spanning-tree detected-protocols interface
GigabitEthernet 1/1

clear spanning-tree detected-protocols interface
10GigabitEthernet
Command:
clear spanning-tree detected-protocols interface
10GigabitEthernet 
 Port list in X/X-XX
Default:
N/A
Usage Guide:

26

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

To clear the spanning-tree detected-protocols for specific 10GigabitEthernet port.
Example:
To clear the Switch’s spanning-tree detected-protocols for specific
10GigabitEthernet 1/1.
Switch# clear spanning-tree detected-protocols interface
10GigabitEthernet 1/1

clear spanning-tree statistics interface *
Command:
clear spanning-tree statistics interface *
Default:
N/A
Usage Guide:
To clear the spanning-tree statistics for all.
Example:
To clear the Switch’s spanning-tree statistics for all.
Switch# clear spanning-tree statistics interface *

clear spanning-tree statistics interface GigabitEthernet
Command:
clear spanning-tree statistics interface GigabitEthernet

 Port list in X/X-XX
Default:
N/A
Usage Guide:
To clear the spanning-tree statistics for specific GigabitEthernet port.
Example:
To clear the Switch’s spanning-tree statistics for specific GigabitEthernet 1/1.
Switch# clear spanning-tree statistics interface GigabitEthernet
1/1

clear spanning-tree statistics interface 10GigabitEthernet
Command:
clear spanning-tree statistics interface 10GigabitEthernet

 Port list in X/X-XX
Default:

NS3500-24T-4C Managed Switch Command Guide

27

Chapter 4: Commands for CLI configuration

N/A
Usage Guide:
To clear the spanning-tree statistics for specific 10GigabitEthernet port.
Example:
To clear the Switch’s spanning-tree statistics for specific 10GigabitEthernet 1/1.
Switch# clear spanning-tree statistics interface 10GigabitEthernet
1/1

clear statistics *
Command:
clear statistics *
Default:
N/A
Usage Guide:
To clear the statistics for all.
Example:
To clear the Switch’s statistics for all.
Switch# clear statistics *

clear statistics GigabitEthernet
Command:
clear statistics GigabitEthernet 


Port list in X/X-XX

Default:
N/A
Usage Guide:
To clear the statistics for specific GigabitEthernet port.
Example:
To clear the Switch’s statistics for specific GigabitEthernet 1/1.
Switch# clear statistics GigabitEthernet 1/1

clear statistics 10GigabitEthernet
Command:
clear statistics 10GigabitEthernet 


Port list in X/X-XX

Default:
N/A
28

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Usage Guide:
To clear the statistics for specific 10GigabitEthernet port.
Example:
To clear the Switch’s statistics for specific 10GigabitEthernet 1/1.
Switch# clear statistics 10GigabitEthernet 1/1

configure terminal
aaa authentication login console local
Command:
aaa authentication login console local
Default:
console : local
Usage Guide:
To authenticate the local account via console only.
Example:
To authenticate the local account via console.
Switch# configure terminal
Switch (config)# aaa authentication login console local

aaa authentication login console radius
Command:
aaa authentication login console radius
Default:
console : local
Usage Guide:
To authenticate the radius account via console only.
Example:
To authenticate the local and radius account via console.
Switch# configure terminal
Switch (config)# aaa authentication login console local radius

aaa authentication login console tacacs
Command:
aaa authentication login console tacacs

NS3500-24T-4C Managed Switch Command Guide

29

Chapter 4: Commands for CLI configuration

Default:
console : local
Usage Guide:
To authenticate the tacacs account via console only.
Example:
To authenticate the local and radius and tacacs account via console.
Switch# configure terminal
Switch (config)# aaa authentication login console local radius
tacacs

aaa authentication login http local
Command:
aaa authentication login http local
Default:
http : local
Usage Guide:
To authenticate the local account via http only.
Example:
To authenticate the local account via http.
Switch# configure terminal
Switch (config)# aaa authentication login http local

aaa authentication login http radius
Command:
aaa authentication login http radius
Default:
http : local
Usage Guide:
To authenticate the radius account via http only.
Example:
To authenticate the local and radius account via http.
Switch# configure terminal
Switch (config)# aaa authentication login http local radius

aaa authentication login http tacacs
Command:
aaa authentication login http tacacs

30

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Default:
http : local
Usage Guide:
To authenticate the tacacs account via http only.
Example:
To authenticate the local and radius and tacacs account via http.
Switch# configure terminal
Switch (config)# aaa authentication login http local radius tacacs

aaa authentication login ssh local
Command:
aaa authentication login ssh local
Default:
ssh : local
Usage Guide:
To authenticate the local account via ssh only.
Example:
To authenticate the local account via ssh.
Switch# configure terminal
Switch (config)# aaa authentication login ssh local

aaa authentication login ssh radius
Command:
aaa authentication login ssh radius
Default:
ssh : local
Usage Guide:
To authenticate the radius account via ssh only.
Example:
To authenticate the local and radius account via ssh.
Switch# configure terminal
Switch (config)# aaa authentication login ssh local radius

aaa authentication login ssh tacacs
Command:
aaa authentication login ssh tacacs

NS3500-24T-4C Managed Switch Command Guide

31

Chapter 4: Commands for CLI configuration

Default:
ssh : local
Usage Guide:
To authenticate the tacacs account via ssh only.
Example:
To authenticate the local and radius and tacacs account via console.
Switch# configure terminal
Switch (config)# aaa authentication login ssh local radius tacacs

aaa authentication login telnet local
Command:
aaa authentication login telnet local
Default:
telnet : local
Usage Guide:
To authenticate the local account via telnet only.
Example:
To authenticate the local account via telnet.
Switch# configure terminal
Switch (config)# aaa authentication login telnet local

aaa authentication login telnet radius
Command:
aaa authentication login telnet radius
Default:
telnet : local
Usage Guide:
To authenticate the radius account via telnet only.
Example:
To authenticate the local and radius account via telnet.
Switch# configure terminal
Switch (config)# aaa authentication login telnet local radius

aaa authentication login telnet tacacs
Command:
aaa authentication login telnet tacacs

32

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Default:
telnet : local
Usage Guide:
To authenticate the tacacs account via telnet only.
Example:
To authenticate the local and radius and tacacs account via telnet.
Switch# configure terminal
Switch (config)# aaa authentication login telnet local radius tacacs

access management
Command:
access management  
 all | snmp | telnet |
to | Web
 ID of access management entry
 The VLAN ID for the access management entry
 Start IPv4 address
 Start IPv6 address
all
All services
snmp
SNMP service
telnet TELNET/SSH service
to
End address of the range
web
Web service
Default:
access management : disable
Usage Guide:
To enable the access management profile to allow SNMP / Telnet / HTTP
services.
Example:
To create a Profile 1 enabling all services for VLAN 1 (IPv6 address 2001::7788) .
Switch# configure terminal
Switch (config)# access management 1 1 2001::7788 all

NS3500-24T-4C Managed Switch Command Guide

33

Chapter 4: Commands for CLI configuration

access-list ace
Command:
access-list ace  action {deny, permit} | dmactype {any, broadcast, multicast, unicast} | frametype {any,
arp, etype, ipv4, ipv4-icmp, ipv4-tcp, ipv4-udp, ipv6, ipv6icmp, ipv6-tcp, ipv6-udp} | ingress {any, interface
10GigabitEthernet | GigabitEthernet } | logging
{disable, next, policy, rate-limiter, shutdown, tag-priority, vid}
| next {, last}| policy  | ratelimiter {, disable} | redirect {disable,
interface 10GigabitEthernet | GigabitEthernet } |
tag-priority {0-1, 0-3, 2-3, 4-5, 4-7, 6-7, , any}
| vid {, any}
 ACE ID
action
Access list action
dmac-type
The type of destination MAC address
frametype
Frame type
ingress
Ingress
logging
Logging frame information. Note: The logging feature only
works when the packet length is less than 1518 (without
VLAN tags) and the System Log memory size and logging rate
are limited.
next
Insert the current ACE before the next ACE ID
policy
Policy
rate-limiter
Rate limiter
redirect
Redirect frame to specific port
shutdown
Shutdown incoming port. The shutdown feature only works
when the packet length is less than 1518 (without VLAN
tags).
tag-priority Tag priority
vid
VID field
Default:
N/A
Usage Guide:
To create and set up a profile for the access list.
Example:
To set a Profile 1 up (action: permit, dmac-type: unicast, frametype: ipv4-icmp,
ingress: any, logging: disable, policy: 1, rate-limiter: 1, tag-priority: 1. vid: 1).
Switch# configure terminal
Switch (config)# access-list ace 1 action permit dmac-type unicast
frametype ipv4-icmp ingress any logging disable policy 1 ratelimiter 1 tag-priority 1 vid 1

34

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

access-list ace update
Command:
access-list ace update  action {deny, permit} |
dmac-type {any, broadcast, multicast, unicast} | frametype
{any, arp, etype, ipv4, ipv4-icmp, ipv4-tcp, ipv4-udp, ipv6,
ipv6-icmp, ipv6-tcp, ipv6-udp} | ingress {any, interface
10GigabitEthernet | GigabitEthernet } | logging
{disable, next, policy, rate-limiter, shutdown, tag-priority, vid}
| next {, last}| policy  | ratelimiter {, disable} | redirect {disable,
interface 10GigabitEthernet | GigabitEthernet } |
tag-priority {0-1, 0-3, 2-3, 4-5, 4-7, 6-7, , any}
| vid {, any}
 ACE ID
action
Access list action
dmac-type
The type of destination MAC address
frametype
Frame type
ingress
Ingress
logging
Logging frame information. Note: The logging feature only
works when the packet length is less than 1518 (without
VLAN tags) and the System Log memory size and logging rate
are limited.
next
Insert the current ACE before the next ACE ID
policy
Policy
rate-limiter
Rate limiter
redirect
Redirect frame to specific port
shutdown
Shutdown incoming port. The shutdown feature only works
when the packet length is less than 1518 (without VLAN
tags).
tag-priority Tag priority
vid
VID field
Default:
N/A
Usage Guide:
To update the specific profile for the access list.
Example:
Original:
Profile 1 (action: permit, dmac-type: unicast, frametype: ipv4-icmp, ingress: any,
logging: disable, policy: 1, rate-limiter: 1, tag-priority: 1. vid: 1).
Updated:
Profile 1 (action: deny, dmac-type: any, frametype: ipv4-icmp, ingress: any,
logging: disable, policy: 1, rate-limiter: 1, tag-priority: 1. vid: 1).
Switch# configure terminal
Switch (config)# access-list ace update 1 action deny dmac-type
any

NS3500-24T-4C Managed Switch Command Guide

35

Chapter 4: Commands for CLI configuration

access-list rate-limiter
Command:
access-list rate-limiter  pps

 Rate limiter ID
 Rate value
Default:
0
Usage Guide:
To set pps rate for specific rate-limiter ID.
Example:
To set pps rate(10000 pps) for specific rate-limiter ID 1.
Switch# configure terminal
Switch (config)# access-list rate-limiter 1 pps 10000

access-list rate-limiter pps
Command:
access-list rate-limiter pps 


Rate value

Default:
0
Usage Guide:
To set pps rate for all rate-limiter ID.
Example:
To set pps rate(10000 pps) for all rate-limiter ID.
Switch# configure terminal
Switch (config)# access-list rate-limiter pps 100

aggregation mode
Command:
aggregation mode dmac | ip | port | smac
dmac Destination MAC affects the distribution
ip
IP address affects the distribution
port IP port affects the distribution
smac Source MAC affects the distribution
Default:
SMAC : Enabled
DMAC : Disabled
IP : Enabled
Port : Enabled

36

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Usage Guide:
To configure static aggregation mode type.
Example:
To configure static aggregation mode type with Destination MAC affects the
distribution and Source MAC affects the distribution only.
Switch# configure terminal
Switch (config)# access-list rate-limiter pps 100

aggregation mode
Command:
aggregation mode dmac | ip | port | smac
dmac Destination MAC affects the distribution
ip
IP address affects the distribution
port IP port affects the distribution
smac Source MAC affects the distribution
Default:
SMAC : Enabled
DMAC : Disabled
IP : Enabled
Port : Enabled
Usage Guide:
To configure static aggregation mode type.
Example:
To configure static aggregation mode type with Destination MAC affects the
distribution and Source MAC affects the distribution only.
Switch# configure terminal
Switch (config)# access-list rate-limiter pps 100

banner
Command:
banner 


c banner-text c, where 'c' is a delimiting character

Default:
N/A
Usage Guide:
To configure banner-text.
Example:
To configure banner-text with word “ddddd”.
Switch# configure terminal
Switch (config)# banner 1
Enter TEXT message. End with the character '1'.

NS3500-24T-4C Managed Switch Command Guide

37

Chapter 4: Commands for CLI configuration

ddddd
1
Telnet 192.168.0.100
ddddd
Username:

banner exec
Command:
banner login 


c banner-text c, where 'c' is a delimiting character

Default:
N/A
Usage Guide:
To configure login banner-text.
Example:
To configure login banner-text with word “wwwwwwwwww”.
Switch# configure terminal
Switch (config)# banner exec 1
Enter TEXT message. End with the character '1'.
gggggg
1
Telnet 192.168.0.100:
Username: admin
Password:
gggggg
#

banner login
Command:
banner login 


c banner-text c, where 'c' is a delimiting character

Default:
N/A
Usage Guide:
To configure login banner-text.
Example:

38

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

To configure login banner-text with word “wwwwwwwwww”.
Switch# configure terminal
Switch (config)# banner login 1
Enter TEXT message. End with the character '1'.
wwwwwwwwww
1
Console:
Press ENTER to get started

wwwwwwwwww

Username: admin
Password:

banner motd
Command:
banner motd 


c banner-text c, where 'c' is a delimiting character

Default:
N/A
Usage Guide:
To configure motd banner-text.
Example:
To configure motd banner-text with word “ffffff”.
Switch# configure terminal
Switch (config)# banner motd 1
Enter TEXT message. End with the character '1'.
ffffff
1
Console:
ffffff

Press ENTER to get started

Username:

NS3500-24T-4C Managed Switch Command Guide

39

Chapter 4: Commands for CLI configuration

clock summer-time
Command:
clock summer-time  date 
  
  
 
Default:
N/A
Usage Guide:
To set daylight saving.
Example:
To set daylight saving (Started time: Feb, 3. 2013 8:8AM, End time: Dec, 31. 2013
8:8AM, Offset time: 60 minutes).
Switch# configure terminal
Switch (config)# clock summer-time 1 date 2 3 2013 8:8 12 31
2013 8:8 60

clock timezone
Command:
clock timezone  


name of time zone

Default:
0
Usage Guide:
To set timezone.
Example:
To set timezone (GMT -15) with profile 1.
Switch# configure terminal
Switch (config)# clock timezone 1 -15

default access-list rate-limiter
Command:
default access-list rate-limiter 


Rate limiter ID

Default:
0
Usage Guide:
To default the Rate limiter.
Example:
To default the Rate limiter ID 1.

40

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# default access-list rate-limiter 1

dot1x authentication timer inactivity
Command:
dot1x authentication timer inactivity <10-1000000>
Default:
Aging period: 300
Usage Guide:
To set the Aging period for Network Access Server.
Example:
To set the Aging period (147 seconds).
Switch# configure terminal
Switch (config)# dot1x authentication timer inactivity 147

dot1x authentication timer re-authenticate
Command:
dot1x authentication timer re-authenticate <1-3600>
Default:
Re-authenticated Period: 3600
Usage Guide:
To set the Re-authenticated Period for Network Access Server.
Example:
To set the Re-authenticated Period (777 seconds).
Switch# configure terminal
Switch (config)# dot1x authentication timer re-authenticate 777

dot1x feature
Command:
dot1x feature guest-vlan | radius-qos | radius-vlan
Default:
Disable
Usage Guide:
To enable the guest-vlan, radius-qos, radius-vlan for Network Access Server
Example:
To enable the guest-vlan, radius-qos, radius-vlan for Network Access Server.

NS3500-24T-4C Managed Switch Command Guide

41

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# dot1x authentication timer re-authenticate 777

dot1x guest-vlan
Command:
dot1x guest-vlan <1-4095>
<1-4095>

Guest VLAN ID used when entering the Guest VLAN.

Default:
1
Usage Guide:
To set the value of guest-vlan for Network Access Server
Example:
To set the value of guest-vlan(2) for Network Access Server
Switch# configure terminal
Switch (config)# dot1x guest-vlan 2

dot1x guest-vlan supplicant
Command:
dot1x guest-vlan supplicant
supplicant

The switch remembers if an EAPOL frame has been received on the port
for the life-time of the port. Once the switch considers whether to enter
the Guest VLAN, it will first check if this option is enabled or disabled.

Default:
Disable
Usage Guide:
To allow all frames automatically entering guest-vlan for Network Access Server
Example:
To allow all frames automatically entering guest-vlan for Network Access Server
Switch# configure terminal
Switch (config)# dot1x guest-vlan supplicant

dot1x max-reauth-req
Command:
dot1x max-reauth-req <1-255>
Default:
2
Usage Guide:

42

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

To define 802.1X re-authentication frequency for Network Access Server
Example:
To define 802.1X re-authentication frequency with 78 times for Network Access
Server
Switch# configure terminal
Switch (config)# dot1x max-reauth-req 78

dot1x system-auth-control
Command:
dot1x system-auth-control
Default:
Disable
Usage Guide:
To enable 802.1X service for Network Access Server
Example:
To enable 802.1X service for Network Access Server
Switch# configure terminal
Switch (config)# dot1x system-auth-control

dot1x timeout quiet-period
Command:
dot1x timeout quiet-period <10-1000000>
quiet-period

Time in seconds before a MAC-address that failed authentication
gets a new authentication chance.

Default:
10
Usage Guide:
To configure 802.1X hold time for Network Access Server
Example:
To configure 802.1X hold time(12 seconds) for Network Access Server
Switch# configure terminal
Switch (config)# dot1x timeout quiet-period 12

dot1x timeout tx-period
Command:
dot1x timeout tx-period <1-65535>
tx-period

The time between EAPOL retransmissions.

Default:
30

NS3500-24T-4C Managed Switch Command Guide

43

Chapter 4: Commands for CLI configuration

Usage Guide:
To configure 802.1X EPOAL timeout for Network Access Server
Example:
To configure 802.1X EPOAL timeout (45 seconds) for Network Access Server
Switch# configure terminal
Switch (config)# dot1x timeout tx-period 45

enable password
Command:
enable password 


The UNENCRYPTED (cleartext) password.

Default:
Disable
Usage Guide:
To configure enable password for user
Example:
To configure enable password(admin) for user
Switch# configure terminal
Switch (config)# enable password admin
Press ENTER to get started
Username:
Password:
> enable
Password: *****
#

enable password level
Command:
enable password level <1-15> 
<1-15>
Level number
 The UNENCRYPTED (cleartext) password.
Default:
Disable
Usage Guide:
To configure enable password and specific level for user

44

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Example:
To configure enable password(admin) and specific level(15) for user
Switch# configure terminal
Switch (config)# enable password level 15 admin
Press ENTER to get started
Username:
Password:
> enable
Password: admin
#

enable secret
Command:
enable secret 0 | 5 level <1-15> 
0 Specifies an UNENCRYPTED password will follow
5 Specifies an ENCRYPTED secret will follow
<1-15> Level number
 The UNENCRYPTED (cleartext) / ENCRYPTED(MD5) password.
Default:
Disable
Usage Guide:
To configure enable password to encrypted secret in the system configurations
and specific level for user
Example:
To configure enable password(cisco) to encrypted secret in the system
configurations and specific level(15) for user
Switch# configure terminal
Switch (config)# enable secret 0 level 15 cisco
# show running-config
Building configuration...
enable secret 5 level 15
FC89368B9513DE0760290BCE9A1DA90A
……………
Press ENTER to get started
Username:
Password:
> enable
Password: cisco
#

NS3500-24T-4C Managed Switch Command Guide

45

Chapter 4: Commands for CLI configuration

end
Command:
end
Default:
N/A
Usage Guide:
To level the configure terminal mode
Example:
To level the configure terminal mode
Switch# configure terminal
Switch (config)# end
#

erps <1-64> guard
Command:
erps <1-64> guard <10-2000>
<1-64> ERPS group number
<10-2000> Guard time in ms
Default:
500
Usage Guide:
To configure the Guard Time for ERPS.
Example:
To configure the Guard Time(178 ms) for ERPS(Profile 1)
Switch# configure terminal
Switch (config)# erps 1 guard 178

erps <1-64> holdoff
Command:
erps <1-64> holdoff < 0-10000>
<1-64> ERPS group number
< 0-10000> Holdoff time in ms
Default:
0
Usage Guide:
To configure the Hold Off Time for ERPS
Example:
To configure the Hold Off Time (178 ms) for ERPS(Profile 1)

46

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# erps 1 holdoff 900

erps <1-64> major
Command:
erps <1-64> major port0 interface {10GigabitEthernet,
GigabitEthernet}  port1 interface
{10GigabitEthernet, GigabitEthernet} 
[ interconnect ]
<1-64> ERPS group number
interconnect Major ring is interconnected
Default:
0
Usage Guide:
To create a profile and configure the Major ERPS interface port 0, port 1.
Example:
To create a profile 1 and configure the Major ERPS interface port
0(GigabitEthernet 1/1), port 1(GigabitEthernet 1/2) without interconnected
mode
Switch# configure terminal
Switch (config)# erps 1 major port0 interface GigabitEthernet
1/1 port1 interface GigabitEthernet 1/2

erps <1-64> mep
Command:
erps <1-64> mep port0 sf  aps 
port1 sf  aps 
<1-64> ERPS group number
 Index of Port 0 SignalFail MEP
 Index of Port 0 APS MEP
 Index of Port 1 SignalFail MEP
 Index of Port 1 APS MEP
Default:
0
Usage Guide:
To configure ERPS Instance Data for specific ERPS profile.
Example:
To configure ERPS Instance Data(Port0: SF MEP = 2, APS MEP = 1. Port1: SF
MEP = 4, APS MEP = 3) for specific ERPS profile(1).
Switch# configure terminal
Switch (config)# erps 1 mep port0 sf 2 aps 1 port1 sf 4 aps 3

NS3500-24T-4C Managed Switch Command Guide

47

Chapter 4: Commands for CLI configuration

erps <1-64> mep
Command:
erps <1-64> revertive 
<1-64> ERPS group number
 Wait-to-restore time in minutes
Default:
0
Usage Guide:
To configure WTR time for specific ERPS profile.
Example:
To configure WTR time(5 minuites) for specific ERPS profile 1.
Switch# configure terminal
Switch (config)# erps 1 revertive 5

erps <1-64> rpl neighbor
Command:
erps <1-64> rpl neighbor { port0 | port1 }
port0
port1

ERPS Port 0 interface
ERPS Port 1 interface

Default:
N/A
Usage Guide:
To configure Ring Protection Link Neighbor Role for specific ERPS interface.
Example:
To configure Ring Protection Link Neighbor Role for specific ERPS interface..
Switch# configure terminal
Switch (config)# erps 1 rpl neighbor port0

erps <1-64> rpl owner
Command:
erps <1-64> rpl owner { port0 | port1 }
port0
port1

ERPS Port 0 interface
ERPS Port 1 interface

Default:
N/A
Usage Guide:
To configure Ring Protection Link Owner Role for specific ERPS interface.
Example:
To configure Ring Protection Link Owner Role for specific ERPS interface..

48

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# erps 1 rpl owner port0

erps <1-64> sub
Command:
erps <1-64> sub port0 interface {10GigabitEthernet,
GigabitEthernet}  { { port0 interface
{10GigabitEthernet, GigabitEthernet}  },
{interconnect  [ virtual-channel ] } }
<1-64> ERPS group number
interconnect Sub ring is interconnected
 Major ring group number
virtual-channel Enable virtual channel for sub-ring
Default:
0
Usage Guide:
To create a profile and configure the Sub ERPS interface port 0, port 1.
Example 1:
To create a profile 3 and configure the Sub ERPS interface port
0(GigabitEthernet 1/5), port 1(GigabitEthernet 1/6) without interconnected
mode and Major RIng group and virtual-channel
Switch# configure terminal
Switch (config)# erps 3 sub port0 interface GigabitEthernet 1/5
port1 interface GigabitEthernet 1/6
Example 2:
To create a profile 2 and configure the Sub ERPS interface port
0(GigabitEthernet 1/3), port 1(GigabitEthernet 1/4) with interconnected mode
and Major RIng group 1 and virtual-channel
Switch# configure terminal
Switch (config)# erps 1 sub port0 interface GigabitEthernet 1/3
interconnect 1 virtual-channel

erps <1-64> topology-change propagate
Command:
erps <1-64> topology-change propagate
<1-64> ERPS group number
topology-change Topology Change
propagate Propagate
Default:
N/A

NS3500-24T-4C Managed Switch Command Guide

49

Chapter 4: Commands for CLI configuration

Usage Guide:
To configure topology change notification (TCN) propagation for the specific
profile.
Example:
To configure topology change notification (TCN) propagation for the specific
profile 1
Switch# configure terminal
Switch (config)# erps 1 topology-change propagate

erps <1-64> topology-change propagate
Command:
erps <1-64> version 1 | 2
<1-64> ERPS group number
version
Version
Default:
V2
Usage Guide:
To configure ERPS version number for the specific profile.
Example:
To configure ERPS version 1 for the specific profile 1.
Switch# configure terminal
Switch (config)# erps 1 version 1

erps <1-64> vlan
Command:
erps <1-64> vlan { none | [ add | remove ]  }
<1-64> ERPS group number
 List of VLANs
add
Add to set of included VLANs
none
Do not include any VLANs
remove
Remove from set of included VLANs
Default:
V2
Usage Guide:
To configure ERPS VLANs for the specific profile.
Example:
To configure ERPS VLANs(VLAN5 - VLAN8) for the specific profile 1.
Switch# configure terminal
Switch (config)# erps 1 vlan add 5-8

50

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

evc
Command:
evc  vid  ivid  interface ( * |
10GigabitEthernet | GigabitEthernet [  ] ) learning
[ disable ] policer {  | none | discard }
 EVC identifier
vid
Setup EVC VLAN ID
 EVC VLAN ID
ivid
Setup internal EVC VLAN ID
 Internal VLAN ID
interface Setup NNI
learning Setup learning
policer
Policer (ingress bandwidth profile)
 Policer ID
 List of VLANs
discard Map to policer discarding all frames
none Map to policer allowing all frames
Default:
0
Usage Guide:
To configure Ethernet Virtual Circuits (EVC).
Example:
To configure Ethernet Virtual Circuits (EVC identifier: 1, EVC VLAN ID: 2,
GigabitEthernet Port: 1/1, 1/2, Internal VLAN ID: 3, Disable learning, Policer
ID: 4).
Switch# configure terminal
Switch (config)# evc 1 vid 2 interface GigabitEthernet 1/1-2 ivid
3 learning disable policer 4

evc ece
Command:
evc ece  direction {both | nni-to-uni | uni-tonni} evc { | none} frame-type {any | ipv4 |
ipv6} inner-tag { add {dei  | pcp 
| preserve | type [c-tag | none | s-custom-tag | s-tag] | vid
}, match {dei [ | any]| pcp
[ | any] | type [any | c-tagged | s-tagged |
tagged | untagged] | vid [ | any]} } interface [* |
10GigabitEthernet | GigabitEthernet]  next
[ | last] outer-tag { add {dei  |
pcp  | preserve | type [c-tag | none | s-customtag | s-tag] | vid }, match {dei [ | any]| pcp [ | any] | mode [disable |
enable] | vid [ | any] } policer { | discard | evc | none} policy  pop


NS3500-24T-4C Managed Switch Command Guide

51

Chapter 4: Commands for CLI configuration



ECE identifier

direction Setup ECE direction
both
Bidirectional traffic flow
nni-to-uni NNI-to-UNI traffic flow
uni-to-nni UNI-to-NNI traffic flow
evc
EVC mapping
 EVC identifier
none
Map to no EVC ID
frame-type Setup matched frame type
any Match any frame type
ipv4 Match IPv4 frames
ipv6 Match IPv6 frames
inner-tag Setup inner tag options
add
Setup inner tag add properties.
dei
Setup added tag DEI
 Added tag DEI
pcp
Setup added tag PCP
 Added tag PCP
preserve Setup tag PCP/DEI preservation
type
Setup added tag type
c-tag
Add C-tag
none
No tag added
s-custom-tag Add custom S-tag
s-tag
Add S-tag
vid
Setup added tag VLAN ID
 Added tag VLAN ID
match Setup inner tag match properties
dei Setup matched DEI
 Matched DEI
any
Match any DEI
pcp Setup matched PCP
 Matched PCP value/range
any
Match any PCP
type Setup matched tag type
any
Match tagged and untagged frames
c-tagged Match C-tagged frames
s-tagged Match S-tagged frames
tagged
Match tagged frames
untagged Match untagged frames
vid Setup matched VLAN ID
 Matched VLAN ID value/range
any
Match any VLAN ID
interface Setup UNI
next
Setup the ECE ID of the next entry
 Select ECE ID of an existing entry

52

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

last

Make the ECE the last entry

outer-tag Setup outer tag options
add
Setup outer tag add properties
dei
Setup added tag DEI
 Added tag DEI
mode
Setup NNI-to-UNI outer tag add mode
disable No tag added when forwarding to UNI
enable Add tag when forwarding to UNI
pcp
Setup added tag PCP
 Added tag PCP
preserve Setup tag PCP/DEI preservation
vid
Setup added tag VLAN ID
 Added tag VLAN ID
match Setup outer tag match properties
policer
Policer (ingress bandwidth profile)
 Policer ID
discard
Map to policer discarding all frames
evc
Use policer setup for EVC
none
Map to policer allowing all frames
policy
Setup ACL policy
 ACL policy
pop
Setup tag popping
 Number of tags popped
Default:
N/A
Usage Guide:
To configure EVC Control Entry.
Example:
To configure EVC Control Entry as tabled below.

NS3500-24T-4C Managed Switch Command Guide

53

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# evc ece 1 direction both evc 2 frame-type ipv4
inner-tag add dei 1 pcp 4 preserve type s-custom-tag vid 5
interface GigabitEthernet 1/3 outer-tag add dei 0 mode enable
pcp 2 vid 7 match dei any pcp any type c-tagged vid 6 policer
8 policy 9 pop 2

evc ece update
Command:
evc ece update  direction {both | nni-to-uni |
uni-to-nni} evc { | none} frame-type {any |
ipv4 | ipv6} inner-tag { add {dei  | pcp
 | preserve | type [c-tag | none | s-custom-tag |
s-tag] | vid }, match {dei [ |
any]| pcp [ | any] | type [any | c-tagged | stagged | tagged | untagged] | vid [ | any]} }
interface [* | 10GigabitEthernet | GigabitEthernet] 
next [ | last] outer-tag { add {dei  | pcp  | preserve | type [c-tag | none | scustom-tag | s-tag] | vid }, match {dei
[ | any]| pcp [ | any] | mode
[disable | enable] | vid [ | any] } policer
{ | discard | evc | none} policy  pop 
 ECE identifier
direction Setup ECE direction
both
Bidirectional traffic flow
nni-to-uni NNI-to-UNI traffic flow
uni-to-nni UNI-to-NNI traffic flow
evc
EVC mapping
 EVC identifier
none
Map to no EVC ID
frame-type Setup matched frame type
any Match any frame type
ipv4 Match IPv4 frames
ipv6 Match IPv6 frames
inner-tag Setup inner tag options
add
Setup inner tag add properties.
dei
Setup added tag DEI
 Added tag DEI
pcp
Setup added tag PCP
 Added tag PCP
preserve Setup tag PCP/DEI preservation
type
Setup added tag type

54

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

c-tag
Add C-tag
none
No tag added
s-custom-tag Add custom S-tag
s-tag
Add S-tag
vid
Setup added tag VLAN ID
 Added tag VLAN ID
match Setup inner tag match properties
dei Setup matched DEI
 Matched DEI
any
Match any DEI
pcp Setup matched PCP
 Matched PCP value/range
any
Match any PCP
type Setup matched tag type
any
Match tagged and untagged frames
c-tagged Match C-tagged frames
s-tagged Match S-tagged frames
tagged
Match tagged frames
untagged Match untagged frames
vid Setup matched VLAN ID
 Matched VLAN ID value/range
any
Match any VLAN ID
interface

Setup UNI

next
Setup the ECE ID of the next entry
 Select ECE ID of an existing entry
last
Make the ECE the last entry
outer-tag Setup outer tag options
add
Setup outer tag add properties
dei
Setup added tag DEI
 Added tag DEI
mode
Setup NNI-to-UNI outer tag add mode
disable No tag added when forwarding to UNI
enable Add tag when forwarding to UNI
pcp
Setup added tag PCP
 Added tag PCP
preserve Setup tag PCP/DEI preservation
vid
Setup added tag VLAN ID
 Added tag VLAN ID
match Setup outer tag match properties
policer
Policer (ingress bandwidth profile)
 Policer ID
discard
Map to policer discarding all frames
evc
Use policer setup for EVC
none
Map to policer allowing all frames
policy
Setup ACL policy
 ACL policy

NS3500-24T-4C Managed Switch Command Guide

55

Chapter 4: Commands for CLI configuration

pop
Setup tag popping
 Number of tags popped
Default:
N/A
Usage Guide:
To update EVC Control Entry for specific ECE profile.
Example 1:
To update “direction nni-to-uni” for ECE profile 1.
Switch# configure terminal
Switch (config)# evc ece 1 direction nni-to-uni

evc policer
Command:
evc policer  [enable | disable] cbs  cir  ebs  eir
 mode [aware | blind | coupled] rate-type
[data | line] type [mef | single]
 Policer ID
cbs
Setup CBS
 Committed Burst Size [bytes]
cir
Setup CIR
 Committed Information Rate [kbps]
disable
Disable policer
ebs
Setup EBS for MEF policer
 Excess Burst Size [bytes]
eir
Setup EIR for MEF policer
 Excess Information Rate [kbps]
enable
Enable policer
mode
Setup policer mode
aware
Color-aware mode
blind
Color-blind mode
coupled Coupling mode
rate-type Setup rate type
data Data rate policing
line Line rate policing
type
Setup policer type
mef
MEF ingress bandwidth profile
single Single bucket policer
Default:
N/A
Usage Guide:
To configure a profile for EVC Policer (Ingress Bandwidth Profile) .
Example:
To configure EVC Policer (Ingress Bandwidth Profile) as tabled below.

56

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# evc policer 1 enable cbs 20 cir 30 ebs 40 eir
50 mode aware rate-type data type mef

evc policer update
Command:
evc policer update  [enable | disable] cbs
 cir  ebs 
eir  mode [aware | blind | coupled] rate-type
[data | line] type [mef | single]
 Policer ID
cbs
Setup CBS
 Committed Burst Size [bytes]
cir
Setup CIR
 Committed Information Rate [kbps]
disable
Disable policer
ebs
Setup EBS for MEF policer
 Excess Burst Size [bytes]
eir
Setup EIR for MEF policer
 Excess Information Rate [kbps]
enable
Enable policer
mode
Setup policer mode
aware
Color-aware mode
blind
Color-blind mode
coupled Coupling mode
rate-type Setup rate type
data Data rate policing
line Line rate policing
type
Setup policer type
mef
MEF ingress bandwidth profile
single Single bucket policer
Default:
N/A
Usage Guide:
To update a profile for EVC Policer (Ingress Bandwidth Profile).
Example:
To update EVC Policer (Ingress Bandwidth Profile) with EIR 1000 for policer 1
Switch# configure terminal
Switch (config)# evc policer update 1 eir 1000

NS3500-24T-4C Managed Switch Command Guide

57

Chapter 4: Commands for CLI configuration

evc update
Command:
evc update  vid  ivid 
interface ( * | 10GigabitEthernet | GigabitEthernet
[  ] ) learning [ disable ] policer {  | none | discard }
 EVC identifier
vid
Setup EVC VLAN ID
 EVC VLAN ID
ivid
Setup internal EVC VLAN ID
 Internal VLAN ID
interface Setup NNI
learning Setup learning
policer
Policer (ingress bandwidth profile)
 Policer ID
 List of VLANs
discard Map to policer discarding all frames
none Map to policer allowing all frames
Default:
0
Usage Guide:
To update an ID for Ethernet Virtual Circuits (EVC).
Example:
To update Ethernet Virtual Circuits (EVC identifier: 1, EVC VLAN ID: 10).
Switch# configure terminal
Switch (config)# evc update 1 vid 10

exit
Command:
exit
Default:
N/A
Usage Guide:
To exit configure terminal mode.
Example:
To exit configure terminal mode.
Switch# configure terminal
Switch (config)# exit
#

58

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

green-ethernet led interval
Command:
green-ethernet led interval <0~24> intensity <0-100>
<0~24> Interval from 00.00 to 24.00 (00 is used to start at midnight,
while 24 is used to stop at midnight).
intensity LEDs intensity.
<0-100> Intensity from 0% (LEDs OFF) to 100%
Default:
N/A
Usage Guide:
To configure LED Power reduction for interval time.
Example:
To configure LED Power reduction as tabled below.

Switch# configure terminal
Switch (config)# green-ethernet led interval 8-13 intensity 80

green-ethernet led on-event
Command:
green-ethernet led on-event error | link-change <0-65535>
error
Set LEDs intensity to 100% if an error occurs.
link-change Specifies how long to turn LEDs intensity into 100%, when a link
changes state.
<0-65535> Number of seconds to set LEDs intensity at 100% at link change.
Default:
N/A
Usage Guide:
To configure LED Power on-event to trigger LED light
Example:
To configure LED Power on-event as tabled below:

Switch# configure terminal
Switch (config)# green-ethernet led on-event error link-change
55

NS3500-24T-4C Managed Switch Command Guide

59

Chapter 4: Commands for CLI configuration

gvrp
Command:
gvrp
Default:
Disable
Usage Guide:
To enable GVRP.
Example:
To enable GVRP.
Switch# configure terminal
Switch (config)# gvrp

gvrp max-vlans
Command:
gvrp max-vlans <1-4095>
Default:
20
Usage Guide:
To configure how many VLANs will be in GVRP.
Example:
To configure 200 VLANs in GVRP.
Switch# configure terminal
Switch (config)# gvrp max-vlans 200

gvrp time
Command:
gvrp time join-time  leave-all-time
 leave-time 
join-time
Set GARP protocol parameter JoinTime. See IEEE 802.1D-2004,
clause 12.11
 join-time in units of centi seconds. Range is 1-20. Default is 20.
leave-all-time Set GARP protocol parameter LeaveAllTime. See IEEE 802.1D2004, clause 12.11
 leave-all-time in units of centi seconds Range is
1000-5000. Default is 1000.
leave-time
Set GARP protocol parameter LeaveTime. See IEEE 802.1D-2004,
clause 12.11
 leave-time in units of centi seconds. Range is 60-300.
Default is 60.
Default:

60

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Usage Guide:
To configure Join-time, Leave-time, Leave all-time for GVRP.
Example:
To configure Join-time, Leave-time, Leave all-time for GVRP as tabled below.

Switch# configure terminal
Switch (config)# gvrp time join-time 5 leave-all-time 1200 leavetime 150

help
Command:
help
Default:
N/A
Usage Guide:
To explain how to use commands.

NS3500-24T-4C Managed Switch Command Guide

61

Chapter 4: Commands for CLI configuration

Example:
To explain how to use commands.
Switch# configure terminal
Switch (config)# help
Help may be requested at any point in a command by entering
a question mark '?'. If nothing matches, the help list will
be empty and you must back up until entering a '?' showing the
available options.
Two styles of help are provided:
1. Full help is available when you are ready to enter a
command argument (e.g. 'show ?') and describes each possible
argument.
2. Partial help is provided when an abbreviated argument is
entered and you want to know what arguments match the input
(e.g. 'show pr?'.)

hostname
Command:
hostname < WORD >
< WORD >

This system's network name

Default:
N/A
Usage Guide:
To configure switch’s hostname.
Example:
To configure switch’s hostname with “IFSbestswitch”
Switch# configure terminal
Switch (config)# hostname IFSbestswitch
IFSbestswitch(config)#

interface * | 10GigabitEthernet | GigabitEthernet
Command:
interface * | 10GigabitEthernet  |
GigabitEthernet 
*
All switches or All ports
GigabitEthernet
1 Gigabit Ethernet Port
10GigabitEthernet 10 Gigabit Ethernet Port
Default:
N/A

62

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Usage Guide:
To enter the interface mode.
Example:
To enter the interface 10GigabitEthernet 1/2
Switch# configure terminal
Switch (config)# interface 10GigabitEthernet 1/2
Switch (config-if) #
access-list action permit
Command:
access-list action permit
action

Access list action

Default:
Permit
Usage Guide:
To configure Permit for the ACL action.
Example:
To configure Permit ACL action for the GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # access-list action permit
access-list action deny
Command:
access-list action deny
action

Access list action

Default:
Deny
Usage Guide:
To configure Deny for the ACL action.
Example:
To configure Deny ACL action for the GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # access-list action deny
access-list logging
Command:
access-list logging
logging

Logging frame information. Note: The logging feature only works when
the packet length is less than 1518 (without VLAN tags) and the

NS3500-24T-4C Managed Switch Command Guide

63

Chapter 4: Commands for CLI configuration

System Log memory size and logging rate is limited.
Default:
Disable
Usage Guide:
To enable Logging function for the ACL.
Example:
To enable ACL Logging function for the GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # access-list logging
access-list policy
Command:
access-list policy 
policy
Policy


Policy ID

Default:
Policy ID: 0
Usage Guide:
To configure Policy ID for the ACL.
Example:
To configure ACL Policy ID 1 for the GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # access-list policy 1
access-list port-state
Command:
access-list port-state
port-state

Re-enable shutdown port that was shutdown by access-list module

Default:
Enable
Usage Guide:
To enable Port-state function for the ACL.
Example:
To configure ACL Port-state function for the GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # access-list port-state

64

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

access-list rate-limiter
Command:
access-list rate-limiter 
rate-limiter Rate limiter


Rate limiter ID

Default:
Disable
Usage Guide:
To apply Rate Limiter ID for the ACL.
Example:
To apply ACL Rate Limiter ID 1 for the GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # access-list rate-limiter 1
access-list redirect interface
Command:
access-list redirect interface 10GigabitEthernet
 | GigabitEthernet 
redirect
Redirect frame to specific port
Default:
Disable
Usage Guide:
To redirect frames to specific Port.
Example:
To redirect GigabitEthernet X/X frames to GigabitEthernet 1/2.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # access-list redirect interface
GigabitEthernet 1/2
access-list shutdown
Command:
access-list shutdown
shutdown

Shut down incoming port. The shutdown feature only works when the
packet length is less than 1518 (without VLAN tags).

Default:
Disable
Usage Guide:
To enable Shutdown function for the ACL.
Example:
To enable ACL Shutdown function for the GigabitEthernet X/X.

NS3500-24T-4C Managed Switch Command Guide

65

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # access-list shutdown
aggregation group
Command:
aggregation group 
aggregation
Create an aggregation
group Create an aggregation group
 The aggregation group id
Default:
N/A
Usage Guide:
To configure aggregation group.
Example:
To configure aggregation group 7 for the GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # aggregation group 7

description
Command:
description 
description
Port description
 specifies a comment or a description of the port to assist the user.
(Length: 1-12 characters)
Default:
N/A
Usage Guide:
To configure port description.
Example:
To configure port description (IPTV_Port) for the GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # description IPTV_Port
do
Command:
do < exec commands >
do

66

To run exec commands in config mode

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Default:
N/A
Usage Guide:
To run exec commands in configure terminal mode
Example:
To run “show aaa” in configure terminal mode.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # do show aaa
console : local
telnet : local
ssh : local
http : local
dot1x guest-vlan
Command:
dot1x guest-vlan
dot1x
IEEE Standard for port-based Network Access Control
guest-vlan Enables/disables guest VLAN
Default:
Disable
Usage Guide:
To enable Guest VLAN
Example:
To enable Guest VLAN for GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # dot1x guest-vlan
dot1x port-control
Command:
dot1x port-control auto | force-authorized | forceunauthorized | mac-based | multi | single
dot1x
IEEE Standard for port-based Network Access Control
port-control
Sets the port security state.
auto
Port-based 802.1X Authentication
force-authorized
Port access is allowed
force-unauthorized Port access is not allowed
mac-based
Switch authenticates on behalf of the client
multi
Multiple Host 802.1X Authentication
single
Single Host 802.1X Authentication
Default:
Force-authorized
Usage Guide:

NS3500-24T-4C Managed Switch Command Guide

67

Chapter 4: Commands for CLI configuration

To configure Port-control mode for 802.1X
Example:
To configure Port-Based 802.1X(Auto) mode for GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # dot1x port-control auto
dot1x radius-qos
Command:
dot1x radius-qos
dot1x
radius-qos

IEEE Standard for port-based Network Access Control
Enables/disables per-port state of RADIUS-assigned QoS.

Default:
Disable
Usage Guide:
To enable RADIUS-assigned QoS for 802.1X
Example:
To enable RADIUS-assigned QoS for GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # dot1x radius-qos
dot1x radius-vlan
Command:
dot1x radius-vlan
dot1x
radius-vlan

IEEE Standard for port-based Network Access Control
Enables/disables per-port state of RADIUS-assigned VLAN.

Default:
Disable
Usage Guide:
To enable RADIUS-assigned VLAN for 802.1X
Example:
To enable RADIUS-assigned VLAN for GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # dot1x radius-vlan
dot1x re-authenticate
Command:
dot1x re-authenticate
dot1x
IEEE Standard for port-based Network Access Control
re-authenticate Refresh (restart) 802.1X authentication process.

68

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Default:
N/A
Usage Guide:
To restart 802.1X authentication process.
Example:
To restart 802.1X authentication process for GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # dot1x re-authenticate
duplex
Command:
duplex auto | full | half
duplex Interface duplex
auto Auto negotiation of duplex mode.
full Forced full duplex.
half Forced half duplex.
Default:
Auto
Usage Guide:
To configure duplex mode for interface.
Example:
To configure auto duplex mode for GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # duplex auto
end
Command:
end
end

Go back to EXEC mode

Default:
Auto
Usage Guide:
To back to EXEC mode
Example:
To back to EXEC mode
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # end
Switch#

NS3500-24T-4C Managed Switch Command Guide

69

Chapter 4: Commands for CLI configuration

excessive-restart
Command:
excessive-restart
excessive-restart

Restart backoff algorithm after 16 collisions (No excessiverestart means discard frame after 16 collisions)

Default:
Discard
Usage Guide:
To enable Backoff Algorithm for the specific interface
Example:
To enable Backoff Algorithm for the GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # excessive-restart
exit
Command:
exit
exit Exit from current mode
Default:
None
Usage Guide:
To exit current mode
Example:
To exit current mode.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # exit
Switch (config)#
flowcontrol
Command:
flowcontrol off | on
flowcontrol
Traffic flow control.
off Disable flow control.
on Enable flow control.
Default:
Disable
Usage Guide:
To enable Flow-control for specific interface
Example:
To enable Flow-control for GigabitEthernet X/X

70

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # flowcontrol on
ip arp inspection check-vlan
Command:
ip arp inspection check-vlan
arp
Address Resolution Protocol
inspection ARP inspection
check-vlan ARP inspection VLAN mode config
Default:
Disable
Usage Guide:
To configure Check-VLAN mode into ARP inspection for specific interface
Example:
To configure Check-VLAN mode (Enabled) into ARP inspection for
GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # ip arp inspection check-vlan
ip arp inspection logging
Command:
ip arp inspection logging all | deny | permit
arp
Address Resolution Protocol
inspection ARP inspection
logging
ARP inspection logging mode config
all
log all entries
deny
log denied entries
permit log permitted entries
Default:
None
Usage Guide:
To configure Logging type into ARP inspection for specific interface
Example:
To configure Logging type (All) into ARP inspection for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # ip arp inspection logging all

NS3500-24T-4C Managed Switch Command Guide

71

Chapter 4: Commands for CLI configuration

ip arp inspection trust
Command:
ip arp inspection trust
arp
Address Resolution Protocol
inspection ARP inspection
trust
ARP inspection trust config
Default:
Trusted
Usage Guide:
To configure Trusted into ARP inspection for specific interface
Example:
To configure Trusted into ARP inspection for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # ip arp inspection trust
ip dhcp snooping trust
Command:
ip dhcp snooping trust
Default:
Trusted
Usage Guide:
To configure Trusted into DHCP Snooping for specific interface
Example:
To configure Trusted into DHCP Snooping for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # ip dhcp snooping trust
ip igmp snooping filter
Command:
ip igmp snooping filter 


Profile name in 16 words

Default:
N/A
Usage Guide:
To apply the IGMP Snooping filter ID for specific interface

72

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Example:
To apply the IGMP Snooping filter ID 1 for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # ip igmp snooping filter 1
ip igmp snooping immediate-leave
Command:
ip igmp snooping immediate-leave
Default:
Disabled
Usage Guide:
To enable IGMP Snooping Immediate-leave (Fast Leave) for specific interface
Example:
To enable IGMP Snooping Immediate-leave (Fast Leave) for GigabitEthernet
X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # ip igmp snooping immediate-leave
ip igmp snooping max-groups
Command:
ip igmp snooping max-groups 
max-groups
IGMP group throttling configuration
 Maximum number of IGMP group registration
Default:
Unlimited
Usage Guide:
To limit maximum number of IGMP group for specific interface
Example:
To limit 5 groups of IGMP for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # ip igmp snooping max-groups 5
ip igmp snooping mrouter
Command:
ip igmp snooping mrouter [ automatic | fix | none ]
mrouter Multicast router port configuration
automatic auto mode
fix fix mode

NS3500-24T-4C Managed Switch Command Guide

73

Chapter 4: Commands for CLI configuration

none

none mode

Default:
Auto
Usage Guide:
To configure Multicast router port mode for specific interface
Example:
To configure Multicast router port mode (fix) for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # ip igmp snooping mrouter fix
ip verify source
Command:
ip verify source
Default:
Disabled
Usage Guide:
To enable IP Source Guard for specific interface
Example:
To enable IP Source Guard for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # ip verify source
ip verify source limit
Command:
ip verify source limit <0-2>
<0-2>

the number of limit

Default:
Unlimited
Usage Guide:
To limit numbers of Dynamic Client for specific interface
Example:
To limit 2 numbers of Dynamic Client for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # ip verify source limit 2

74

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

ipv6 mld snooping filter
Command:
ipv6 mld snooping filter 
filter
Access control on MLD multicast group registration
 Profile name in 16 words
Default:
N/A
Usage Guide:
To apply the MLD Snooping filter ID for specific interface
Example:
To apply the MLD Snooping filter ID 1 for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # ipv6 mld snooping filter 1
ipv6 mld snooping immediate-leave
Command:
ipv6 mld snooping immediate-leave
Default:
Disabled
Usage Guide:
To enable MLD Snooping Immediate-leave (Fast Leave) for specific interface
Example:
To enable MLD Snooping Immediate-leave (Fast Leave) for GigabitEthernet
X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # ipv6 mld snooping immediate-leave
ipv6 mld snooping max-groups
Command:
ipv6 mld snooping max-groups 
max-groups
IGMP group throttling configuration
 Maximum number of IGMP group registration
Default:
Unlimited
Usage Guide:
To limit maximum number of MLD group for specific interface
Example:
To limit 5 groups of MLD for GigabitEthernet X/X

NS3500-24T-4C Managed Switch Command Guide

75

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # ipv6 mld snooping max-groups 5
ipv6 mld snooping mrouter
Command:
ipv6 mld snooping mrouter [ automatic | fix | none]
mrouter Multicast router port configuration
automatic auto mode
fix fix mode
none none mode
Default:
Auto
Usage Guide:
To configure MLD router port mode for specific interface
Example:
To configure MLD router port mode (fix) for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # ipv6 mld snooping mrouter fix
lacp
Command:
lacp
lacp

Enable LACP on this interface

Default:
Disabled
Usage Guide:
To enable LACP for specific interface
Example:
To enable LACP for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # lacp
lacp key
Command:
lacp key <1-65535> | auto
lacp
Enable LACP on this interface
key
Key of the LACP aggregation
<1-65535> Key value
auto
Choose a key based on port speed

76

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Default:
Auto
Usage Guide:
To configure LACP key for specific interface
Example:
To configure LACP key (555) for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # lacp key 555
lacp port-priority
Command:
lacp port-priority <1-65535>
lacp
Enable LACP on this interface
port-priority LACP priority of the port
<1-65535> Priority value, lower means higher priority
Default:
32768
Usage Guide:
To configure LACP port-priority for specific interface
Example:
To configure LACP port-priority (555) for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # lacp port-priority 555
lacp role
Command:
lacp role active | passive
lacp
Enable LACP on this interface
role
Active / Passive (speak if spoken to) role
active Transmit LACP BPDUs continously
passive Wait for neighbour LACP BPDUs before transmitting
Default:
Active
Usage Guide:
To configure LACP role for specific interface

NS3500-24T-4C Managed Switch Command Guide

77

Chapter 4: Commands for CLI configuration

Example:
To configure LACP role (passive) for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # lacp role passive
lacp timeout
Command:
lacp timeout fast | slow
lacp
Enable LACP on this interface
timeout The period between BPDU transmissions
fast
Transmit BPDU each second (fast timeout)
slow Transmit BPDU each 30th second (slow timeout)
Default:
Fast
Usage Guide:
To configure LACP timeout type for specific interface
Example:
To enable LACP timeout type (slow) for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # lacp timeout slow
lldp cdp-aware
Command:
lldp cdp-aware
lldp
LLDP configurations
cdp-aware Configures if the interface shall be CDP aware (CDP discovery
information is added to the LLDP neighbor table)
Default:
Passive
Usage Guide:
To configure MIB variable retrieve local info or remote info of LLDP for specific
interface
Example:
To configure MIB variable retrieve (local info) of LLDP for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # lldp cdp-aware

78

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

lldp med media-vlan policy-list
Command:
lldp med media-vlan policy-list 
lldp
LLDP configurations
med
Media Endpoint Discovery
media-vlan
Media VLAN assignment
policy-list
Assignment of policies
 Policies to assign to the interface
Default:
N/A
Usage Guide:
To apply MED Media-VLAN policy of LLDP for specific interface
Example:
To apply MED Media-VLAN policy 2 of LLDPfor GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # lldp med media-vlan policy-list 2
lldp med transmit-tlv
Command:
lldp med transmit-tlv [ capabilities ] [ location ] [ networkpolicy ]
lldp
LLDP configurations
med
Media Endpoint Discovery
transmit-tlv LLDP-MED Location Type Length Value parameter.
capabilities
Enable transmission of the optional capabilities TLV.
location
Enable transmission of the optional location TLV.
network-policy Enable transmission of the optional network-policy TLV.
Default:
N/A
Usage Guide:
To configure LLDP-MED TLV Type for specific interface
Example:
To enable LLDP-MED TLV (capabilities and location) for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # lldp med transmit-tlv capabilities location
lldp receive
Command:
lldp receive
lldp
receive

LLDP configurations
Enable/Disable decoding of received LLDP frames.

NS3500-24T-4C Managed Switch Command Guide

79

Chapter 4: Commands for CLI configuration

Default:
Both (Tx +Rx)
Usage Guide:
To configure LLDP Rx only mode for specific interface
Example:
To configure LLDP Rx only mode for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # lldp receive

lldp tlv-select management-address
Command:
lldp tlv-select management-address
lldp
LLDP configurations
tlv-select To transmit which optional TLVs.
management-address Enable/Disable transmission of management address.
Default:
Enabled
Usage Guide:
To enable management address of LLDP TLV for specific interface
Example:
To enable management address of LLDP TLV for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # lldp tlv-select management-address
lldp tlv-select port-description
Command:
lldp tlv-select port-description
lldp
LLDP configurations
tlv-select To transmit which optional TLVs.
port-description
Enable/Disable transmission of port description.
Default:
Enabled
Usage Guide:
To enable port-description of LLDP TLV for specific interface
Example:
To enable port-description of LLDP TLV for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # lldp tlv-select port-description

80

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

lldp tlv-select system-capabilities
Command:
lldp tlv-select system-capabilities
lldp
LLDP configurations
tlv-select To transmit which optional TLVs.
system-capabilities Enable/Disable transmission of system capabilities.
Default:
Enabled
Usage Guide:
To enable system-capabilities of LLDP TLV for specific interface
Example:
To enable system-capabilities of LLDP TLV for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # lldp tlv-select system-capabilities
lldp tlv-select system-description
Command:
lldp tlv-select system-description
lldp
LLDP configurations
tlv-select To transmit which optional TLVs.
system-description Enable/Disable transmission of system description.
Default:
Enabled
Usage Guide:
To enable system-description of LLDP TLV for specific interface
Example:
To enable system-description of LLDP TLV for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # lldp tlv-select system-description
lldp tlv-select system-name
Command:
lldp tlv-select system-name
lldp
LLDP configurations
tlv-select
To transmit which optional TLVs.
system-name Enable/Disable transmission of system name.
Default:
Enabled
Usage Guide:
To enable system-name of LLDP TLV for specific interface
Example:
NS3500-24T-4C Managed Switch Command Guide

81

Chapter 4: Commands for CLI configuration

To enable system-name of LLDP TLV for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # lldp tlv-select system-name
lldp transmit
Command:
lldp transmit
lldp
LLDP configurations
transmit
Enable/Disabled transmision of LLDP frames.
Default:
Both (Tx +Rx)
Usage Guide:
To configure LLDP Tx only mode for specific interface
Example:
To configure LLDP Tx only mode for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # lldp transmit
loop-protect
Command:
loop-protect
loop-protect

Loop protection configuration

Default:
Enabled
Usage Guide:
To enable loop-protect for specific interface
Example:
To enable loop-protect for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # loop-protect
loop-protect action
Command:
loop-protect action [log] [shutdown]
loop-protect
Loop protection configuration
action Action if loop detected
log
Generate log
shutdown Shutdown port

82

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Default:
Shutdown
Usage Guide:
To configure action mode of Loop protection for specific interface
Example:
To configure action mode (log and shutdown) of Loop protection for
GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # loop-protect action shutdown log
loop-protect tx-mode
Command:
loop-protect tx-mode
loop-protect Loop protection configuration
tx-mode Actively generate PDUs
Default:
Enabled
Usage Guide:
To enable tx-mode of Loop protection for specific interface
Example:
To enable tx-mode of Loop protection for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # loop-protect tx-mode
loop-protect tx-mode
Command:
loop-protect tx-mode
loop-protect Loop protection configuration
tx-mode Actively generate PDUs
Default:
Enabled
Usage Guide:
To enable tx-mode of Loop protection for specific interface
Example:
To enable tx-mode of Loop protection for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # loop-protect tx-mode
mac address-table learning
Command:

NS3500-24T-4C Managed Switch Command Guide

83

Chapter 4: Commands for CLI configuration

mac address-table learning [secure]
mac
MAC keyword
address-table MAC table configuration
learning Port learning mode
secure Port Secure mode
Default:
Enabled (Auto)
Usage Guide:
To enable learning of MAC address table for specific interface
Example:
To enable learning of MAC address table for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # mac address-table learning
media-type
Command:
media-type dual | rj45 | sfp
media-type
Media type.
dual Dual media interface (copper & fiber interface).
rj45 rj45 interface (copper interface).
sfp sfp interface (fiber interface).
Default:
N/A
Usage Guide:
To configure Copper or Fiber mode of media type for specific interface
Example:
To configure Copper mode of media type for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # media-type rj45
mtu
Command:
mtu <1518-10056>
mtu
Maximum transmission unit
<1518-10056> Maximum frame size in bytes.
Default:
10056
Usage Guide:
To configure MTU sizes for specific interface
Example:
To configure MTU sizes (9000) for GigabitEthernet X/X

84

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # mtu 9000
mvr immediate-leave
Command:
mvr immediate-leave
mvr
Multicast VLAN Registration configuration
immediate-leave Immediate leave configuration
Default:
Disabled
Usage Guide:
To enable Immediate-leave of MVR for specific interface
Example:
To enable Immediate-leave of MVR for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # mvr immediate-leave
mvr name
Command:
mvr name  type [receiver | source]
mvr
Multicast VLAN Registration configuration
name
MVR multicast name
 MVR multicast VLAN name
type MVR port role configuration
receiver MVR receiver port
source
MVR source port
Default:
Inactive
Usage Guide:
To configure port role of specific MVR profile for specific interface
Example:
To configure port role (source) of MVR profiles (111) for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # mvr name 111 type source
mvr vlan
Command:
mvr vlan  type [source | receiver ]
mvr
vlan

Multicast VLAN Registration configuration
MVR multicast vlan

NS3500-24T-4C Managed Switch Command Guide

85

Chapter 4: Commands for CLI configuration

 MVR multicast VLAN list
type MVR port role configuration
receiver MVR receiver port
source
MVR source port
Default:
Inactive
Usage Guide:
To configure port role of specific MVR VLAN ID for specific interface
Example:
To configure port role (source) of MVR VLAN ID (111) for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # mvr name 111 type source
network-clock synchronization ssm
Command:
network-clock synchronization ssm
network-clock network-clock
synchronization SSM enable/disable.
ssm SSM enable/disable.
Default:
Disable
Usage Guide:
To enable SSM of SyncE for specific interface
Example:
To enable SSM of SyncE for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # network-clock synchronization ssm
no
Command:
no
no

Negate a command or set its defaults

Default:
N/A
Usage Guide:
To default the function for specific interface

86

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Example:
To enable the function (network-clock synchronization ssm) for
GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # no network-clock synchronization ssm
ping ip
Command:
ping ip  size 
ping The ping command allows you to test connectivity to a network host from the
appliance
ip ip
 IP address
size size
 Default is 56 (excluding MAC, IP and ICMP headers)
Default:
N/A
Usage Guide:
To run Ping function for specific interface
Example:
To run Ping function (IP address: 10.10.10.10 with size 88 bytes) for
GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # ping ip 10.10.10.10 size 88
poe mode
Command:
poe mode { standard | plus }
poe
Power Over Ethernet.
mode
PoE mode.
plus
Set mode to PoE+ (Maximum power 30.0 W)
standard Set mode to PoE (Maximum power 15.4 W)
Default:
N/A
Usage Guide:
To configure 802.3at/af mode for specific interface
Example:
To configure 802.3at mode for GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # poe mode plus

NS3500-24T-4C Managed Switch Command Guide

87

Chapter 4: Commands for CLI configuration

poe pdcheck IP
Command:
poe pdcheck IP 
poe
Power Over Ethernet.
pdcheck
Allows user to enable or disable per port PD Alive Check function.
IP
To set PoE device IP address here for system making ping to the PoE
device.
 
Default:
N/A
Usage Guide:
To configure Ping PD IP Address of PoE for specific interface
Example:
To configure Ping PD IP Address (10.101.10.10) of PoE for GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # poe pdcheck IP 10.101.10.10
poe pdcheck action
Command:
poe pdcheck action { reboot | alarm | reboot-alarm }
poe
Power Over Ethernet.
pdcheck
Allows user to enable or disable per port PD Alive Check function.
action
Allows user to set which action will be applied if the
PD is without any response
alarm
It means system will issue an alarm message via Syslog, SMTP.
reboot
It means system will reset the PoE port that is connected to the PD.
reboot-alarm
It means system will reset the PoE port and issue an alarm
message via Syslog, SMTP.
Default:
N/A
Usage Guide:
To configure PD Ping Alive Check Action of PoE for specific interface
Example:
To configure PD Ping Alive Check Action (Alarm) of PoE for GigabitEthernet
X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # poe pdcheck action alarm
poe pdcheck enable
Command:
poe pdcheck enable
poe
88

Power Over Ethernet.
NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

pdcheck
Allows user to enable or disable per port PD Alive Check function.
enable
PD alive check enable.
Default:
Disabled
Usage Guide:
To enable PD Ping Alive Check function of PoE for specific interface.
Example:
To enable PD Ping Alive Check function of PoE for GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # poe pdcheck enable
poe pdcheck interval
Command:
poe pdcheck interval <10-300>
poe
Power Over Ethernet.
pdcheck
Allows user to enable or disable per port PD Alive Check function.
interval set how long system should be issue a ping request to PD for detecting
whether PD is alive or dead.
<10-300> interval <10~300>
Default:
30
Usage Guide:
To configure PD Ping Alive Check interval of PoE for specific interface.
Example:
To configure PD Ping Alive Check interval (100 seconds) of PoE for
GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # poe pdcheck interval 100
poe pdcheck reboot-time
Command:
poe pdcheck reboot-time <30-180>
poe
Power Over Ethernet.
pdcheck
Allows user to enable or disable per port PD Alive Check function.
reboot-time set the PoE device rebooting time.
<30-180> reboot-time <30-180>
Default:
90
Usage Guide:
To configure PD Ping Alive Check rebooting time of PoE for specific interface.
Example:
To configure PD Ping Alive Check rebooting time (100 seconds) of PoE for
NS3500-24T-4C Managed Switch Command Guide

89

Chapter 4: Commands for CLI configuration

GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # poe pdcheck reboot-time 100
poe pdcheck retry-count
Command:
poe pdcheck retry-count <1-5>
poe
Power Over Ethernet.
pdcheck
Allows user to enable or disable per port PD Alive Check function.
retry-count set how many times system retry ping to PD.
<1-5> retry-count <1-5>
Default:
2
Usage Guide:
To configure PD Ping Alive Check retry count of PoE for specific interface.
Example:
To configure PD Ping Alive Check retry count (5) of PoE for GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # poe pdcheck retry-count 5

poe power limit
Command:
poe power limit { }
poe
Power Over Ethernet.
power
Setting maximum power for port in allocation mode.
limit The maximum power.
 Maximum power for the interface (0-15.4 Watt
for PoE standard mode, 0-30.0 Watt for PoE plus
mode)
Default:
2
Usage Guide:
To configure maximum power of PoE for specific interface.
Example:
To configure maximum power (29 watts) of PoE for GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # poe power limit 29

90

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

poe priority
Command:
poe priority { low | high | critical }
poe
Power Over Ethernet.
priority
Interface priority.
critical Set priority to critical.
high
Set priority to high.
low
Set priority to low.
Default:
2
Usage Guide:
To configure interface priority of PoE for specific interface.
Example:
To configure interface priority (low) of PoE for GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # poe priority low
poe time-range
Command:
poe time-range { profile1 | profile2 | profile3 | profile4 }
poe
Power Over Ethernet.
time-range To bind a PoE time-range to the corresponding port.
profile1 The profile name of the PoE time-range to be bound to the port.
profile2 The profile name of the PoE time-range to be bound to the port.
profile3 The profile name of the PoE time-range to be bound to the port.
profile4 The profile name of the PoE time-range to be bound to the port.
Default:
Profile 1
Usage Guide:
To configure time-range profile of PoE for specific interface.
Example:
To configure time-range profile (Profile 3) of PoE for GigabitEthernet X/X.
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # poe time-range profile3
port-security
Command:
port-security
port-security

Enable/disable port security per interface.

Default:
Disabled
Usage Guide:
NS3500-24T-4C Managed Switch Command Guide

91

Chapter 4: Commands for CLI configuration

To enable Port-security for specific interface
Example:
To enable Port-security for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # port-security
port-security maximum
Command:
port-security maximum 
port-security
Enable/disable port security per interface.
maximum
Maximum number of MAC addresses that can be learned on this set
of interfaces.
 Number of addresses
Default:
None
Usage Guide:
To configure number of Port-security addresses for specific interface
Example:
To configure 100 Port-security addresses for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # port-security maximum 100
port-security violation
Command:
port-security violation [protect | shutdown | trap | trapshutdown]
port-security Enable/disable port security per interface.
violation The action involved with exceeding the limit.
protect
Don't do anything
shutdown
Shut down the port
trap
Send an SNMP trap
trap-shutdown Send an SNMP trap and shut down the port
Default:
None (Protected)
Usage Guide:
To configure protected mode of Port-security for specific interface
Example:
To configure protected mode (trap-shutdown) of Port-security for
GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # port-security violation trap-shutdown

92

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

port-security violation
Command:
port-security violation [protect | shutdown | trap | trapshutdown]
port-security
Enable/disable port security per interface.
violation The action involved with exceeding the limit.
protect
Don't do anything
shutdown
Shutdown the port
trap
Send an SNMP trap
trap-shutdown Send an SNMP trap and shut down the port
Default:
None (Protected)
Usage Guide:
To configure protected mode of Port-security for specific interface
Example:
To configure protected mode (trap-shutdown) of Port-security for
GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # port-security violation trap-shutdown
pvlan
Command:
pvlan 
pvlan
Private VLAN
 list of PVLANs. Range is from 1 to number of ports.
Default:
None
Usage Guide:
To create PVLAN ID for specific interface
Example:
To create PVLAN ID (5) for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # pvlan 5
pvlan isolation
Command:
pvlan isolation
pvlan
isolation

Private VLAN
Port isolation

Default:
None

NS3500-24T-4C Managed Switch Command Guide

93

Chapter 4: Commands for CLI configuration

Usage Guide:
To enable PVLAN isolation for specific interface
Example:
To enable PVLAN isolation for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # pvlan isolation
qos cos
Command:
qos cos 
qos
Quality of Service
cos
Class of service configuration
 Specific class of service
Default:
0
Usage Guide:
To configure CoS of QoS for specific interface
Example:
To configure CoS (4) of QoS for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # qos cos 4
qos dei
Command:
qos dei 
qos
Quality of Service
dei
Drop Eligible Indicator configuration
 Specific Drop Eligible Indicator
Default:
0
Usage Guide:
To configure DEI of QoS for specific interface
Example:
To configure DEI (1) of QoS for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # qos dei 1
qos dpl
Command:
qos dpl 

94

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

qos
Quality of Service
dpl
Drop precedence level configuration
 Specific drop precedence level
Default:
0
Usage Guide:
To configure DPL of QoS for specific interface
Example:
To configure DPL (1) of QoS for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # qos dpl 1
qos dscp-classify
Command:
qos dscp-classify any | selected | zero
qos
Quality of Service
dscp-classify DSCP ingress classification
any
Classify to new DSCP always
selected Classify to new DSCP if classify is enabled for specific DSCP value in
global dscp-classify map
zero
Classify to new DSCP if DSCP is 0
Default:
Disabled
Usage Guide:
To configure DSCP Classify of QoS for specific interface
Example:
To configure DSCP Classify (Any) of QoS for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # qos dscp-classify any
qos dscp-remark
Command:
qos dscp-remark remap | rewrite
qos
Quality of Service
dscp-remark DSCP egress remarking
remap
Rewrite DSCP field using classified DSCP remapped through global
dscp-egress-translation map
rewrite Rewrite DSCP field with classified DSCP value (no translation)
Default:
Disabled
Usage Guide:
To configure DSCP egress remarking of QoS for specific interface
NS3500-24T-4C Managed Switch Command Guide

95

Chapter 4: Commands for CLI configuration

Example:
To configure DSCP egress remarking (Remap) of QoS for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # qos dscp-remark remap
qos dscp-translate
Command:
qos dscp-translate
qos
Quality of Service
dscp-translate DSCP ingress translation
Default:
Disabled
Usage Guide:
To configure DSCP ingress translation of QoS for specific interface
Example:
To configure DSCP ingress translation of QoS for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # qos dscp-translate
qos map cos-tag
Command:
qos map cos-tag cos  dpl  pcp  dei 
qos
Quality of Service
map
QoS Map/Table configuration
cos-tag Map for cos to tag configuration
cos Specify class of service
 Specific class of service or range
dpl Specify drop precedence level
 Specific drop precedence level or range
pcp Specify PCP (Priority Code Point)
 Specific PCP
dei Specify DEI (Drop Eligible Indicator)
 Specific DEI
Default:
Disabled
Usage Guide:
To configure (QoS class, DP level) to (PCP, DEI) Mapping of QoS for specific
interface
Example:
To configure (QoS class, DP level) to (PCP, DEI) Mapping of QoS as below table
for GigabitEthernet X/X

96

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # qos map cos-tag cos 1 dpl 1 pcp 6 dei 0
qos map tag-cos
Command:
qos map tag-cos pcp  dei  cos  dpl 
qos
Quality of Service
map
QoS Map/Table configuration
tag-cos Map for tag to cos configuration
pcp Specify PCP (Priority Code Point)
 Specific PCP
dei Specify DEI (Drop Eligible Indicator)
 Specific DEI
cos Specify class of service
 Specific class of service or range
dpl Specify drop precedence level
 Specific drop precedence level or range
Default:
Disabled
Usage Guide:
To configure (PCP, DEI) to (QoS class, DP level) Mapping of QoS for specific
interface
Example:
To configure (PCP, DEI) to (QoS class, DP level) Mapping of QoS as below table
for GigabitEthernet X/X

Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # qos map tag-cos pcp 4 dei 0 cos 5 dpl 1
qos pcp
Command:
qos pcp 
qos
Quality of Service
pcp
Priority Code Point configuration
 Specific Priority Code Point
Default:

NS3500-24T-4C Managed Switch Command Guide

97

Chapter 4: Commands for CLI configuration

0
Usage Guide:
To configure PCP of QoS for specific interface
Example:
To configure PCP (6) of QoS for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # qos pcp 6
qos policer
Command:
qos policer 
qos
Quality of Service
policer
Policer configuration
 Policer rate (default kbps)
Default:
0
Usage Guide:
To configure Ingress Port Policers Rate of QoS for specific interface
Example:
To configure Ingress Port Policers Rate (9999 Kbps) of QoS for GigabitEthernet
X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # qos policer 9999
qos queue-policer queue
Command:
qos queue-policer queue  
qos
Quality of Service
queue-policer Queue policer configuration
queue Specify queue
 Specific queue or range
 Policer rate in kbps
Default:
0
Usage Guide:
To configure Ingress Queue Policers Rate of QoS for specific interface
Example:
To configure Ingress Queue (4) Policers Rate (9999 Kbps) of QoS for
GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X

98

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch (config-if) # qos queue-policer queue 4 9999
qos queue-shaper queue
Command:
qos queue-shaper queue  
qos
Quality of Service
queue-shaper Queue shaper configuration
queue Specify queue
 Specific queue or range
 Policer rate in kbps
Default:
0
Usage Guide:
To configure Egress Queue Shapers Rate of QoS for specific interface
Example:
To configure Egress Queue (4) Shapers Rate (9999 Kbps) of QoS for
GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # qos queue-shaper queue 4 9999
qos shaper
Command:
qos shaper 
qos
Quality of Service
shaper
Shaper configuration
 Shaper rate in kbps
Default:
0
Usage Guide:
To configure Egress Port Shapers Rate of QoS for specific interface
Example:
To configure Egress Port (4) Shapers Rate (9999 Kbps) of QoS for
GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # qos queue-shaper queue 4 9999
qos storm broadcast
Command:
qos storm broadcast  [fps]

NS3500-24T-4C Managed Switch Command Guide

99

Chapter 4: Commands for CLI configuration

qos
Quality of Service
storm
Storm policer
broadcast Police broadcast frames
 Policer rate (default kbps)
fps Rate is fps
Default:
500
Usage Guide:
To configure Broadcast Frames Storm Control Rate of QoS for specific interface
Example:
To configure Broadcast Frames Storm Control Rate (999 fps) of QoS for
GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # qos storm broadcast 999 fps
qos storm unicast
Command:
qos storm unicast  [fps]
qos
Quality of Service
storm
Storm policer
unicast
Police unicast frames
 Policer rate (default kbps)
fps Rate is fps
Default:
500
Usage Guide:
To configure Unicast Frames Storm Control Rate of QoS for specific interface
Example:
To configure Unicast Frames Storm Control Rate (999 Kbps) of QoS for
GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # qos storm unicast 999
qos storm unknown
Command:
qos storm unknown  [fps]
qos
Quality of Service
storm
Storm policer
unknown
Police unknown (flooded) frames
 Policer rate (default kbps)
fps Rate is fps
Default:
500
100

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Usage Guide:
To configure Unknown Frames Storm Control Rate of QoS for specific interface
Example:
To configure Unknown Frames Storm Control Rate (999 fps) of QoS for
GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # qos storm unicast 999 fps
qos tag-remark
Command:
qos tag-remark pcp  dei 
qos
Quality of Service
tag-remark
Tag remarking configuration
pcp
Specify default PCP
 Specific PCP
dei Specify default DEI
 Specific DEI
Default:
0
Usage Guide:
To enable Tag-remark default mode of QoS for specific interface
Example:
To enable Tag-remark default mode (PCP:1 , DEI:1) of QoS for GigabitEthernet
X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # qos tag-remark pcp 1 dei 1
qos tag-remark mapped
Command:
qos tag-remark mapped
qos
Quality of Service
tag-remark
Tag remarking configuration
mapped Used mapped values (cos,dpl -> pcp,dei)
Default:
Classified
Usage Guide:
To enable Tag-remark mapped mode of QoS for specific interface

NS3500-24T-4C Managed Switch Command Guide

101

Chapter 4: Commands for CLI configuration

Example:
To enable Tag-remark mapped mode of QoS for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # qos tag-remark mapped
qos trust dscp
Command:
qos trust dscp
qos Quality of Service
trust Trust configuration
dscp DSCP value
Default:
Disabled
Usage Guide:
To enable DSCP Classification of QoS for specific interface
Example:
To enable DSCP Classification of QoS for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # qos trust dscp
qos trust tag
Command:
qos trust tag
qos Quality of Service
trust Trust configuration
tag VLAN tag
Default:
Disabled
Usage Guide:
To enable VLAN tag Classification of QoS for specific interface
Example:
To enable VLAN tag Classification of QoS for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # qos trust tag
rmon collection history
Command:
rmon collection history <1-65535> buckets <1-65535> interval
<1-3600>
rmon
Configure Remote Monitoring on an interface
102

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

collection Configure Remote Monitoring Collection on an interface
history Configure history
buckets Requested buckets of intervals. Default is 50 buckets
interval Interval to sample data for each bucket. Default is 1800 seconds
Default:
N/A
Usage Guide:
To configure RMON History Configuration for specific interface
Example:
To configure RMON History Configuration as below table for GigabitEthernet
X/X

Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # rmon collection history 1 buckets 5 interval
3
rmon collection stats
Command:
rmon collection stats <1-65535>
rmon
Configure Remote Monitoring on an interface
collection Configure Remote Monitoring Collection on an interface
stats
Configure statistics
Default:
0
Usage Guide:
To configure RMON Statistics Configuration for specific interface
Example:
To configure RMON Statistics Configuration (2) as below table for
GigabitEthernet X/X

Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # rmon collection stats 2
shutdown
Command:
shutdown

NS3500-24T-4C Managed Switch Command Guide

103

Chapter 4: Commands for CLI configuration

shutdown

Shutdown of the interface.

Default:
No shutdown
Usage Guide:
To shut down specific interface
Example:
To shut down GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # shutdown
spanning-tree
Command:
spanning-tree
spanning-tree

Spanning Tree protocol

Default:
Disabled
Usage Guide:
To enable STP for specific interface
Example:
To enable STP for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # spanning-tree
spanning-tree auto-edge
Command:
spanning-tree auto-edge
spanning-tree
Spanning Tree protocol
auto-edge
Auto detects edge status
Default:
Enabled
Usage Guide:
To enable Auto Edge of CIST Normal Port Configuration for specific interface
Example:
To enable Auto Edge of CIST Normal Port Configuration for GigabitEthernet
X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # spanning-tree auto-edge

104

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

spanning-tree bpdu-guard
Command:
spanning-tree bpdu-guard
spanning-tree
Spanning Tree protocol
auto-edge
Auto detects edge status
Default:
Disabled
Usage Guide:
To enable BPDU Guard of CIST Normal Port Configuration for specific interface
Example:
To enable BPDU Guard of CIST Normal Port Configuration for GigabitEthernet
X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # spanning-tree bpdu-guard
spanning-tree edge
Command:
spanning-tree edge
spanning-tree
Spanning Tree protocol
edge
Edge port
Default:
Non-Edge
Usage Guide:
To enable edge port of CIST Normal Port Configuration for specific interface
Example:
To enable edge port of CIST Normal Port Configuration for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # spanning-tree edge
spanning-tree link-type
Command:
spanning-tree link-type auto | point-to-point | shared
spanning-tree Spanning Tree protocol
link-type
Port link-type
auto
Auto detect
point-to-point Forced to point-to-point
shared
Forced to Shared
Default:
Auto
Usage Guide:
To configure point to point mode of CIST Normal Port Configuration for specific
NS3500-24T-4C Managed Switch Command Guide

105

Chapter 4: Commands for CLI configuration

interface
Example:
To enable point to point mode (shared) of CIST Normal Port Configuration for
GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # spanning-tree edge
spanning-tree mst  cost
Command:
spanning-tree mst  cost 
| auto
spanning-tree
Spanning Tree protocol
mst
STP bridge instance
 instance 0-7 (CIST=0, MST2=1...)
cost
STP Cost of this port
 Cost range
auto
Use auto cost
Default:
Auto
Usage Guide:
To configure Path Cost of CIST / MST Normal Port Configuration for specific
interface
Example:
To enable Path Cost (100) of CIST / MST Normal Port Configuration (CIST) for
GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # spanning-tree mst 0 cost 100
spanning-tree mst  cost
Command:
spanning-tree mst  port-priority 
spanning-tree
Spanning Tree protocol
mst
STP bridge instance
 instance 0-7 (CIST=0, MST2=1...)
port-priority STP priority of this port
 Range (lower higher priority)
auto
Use auto cost
Default:
Auto
Usage Guide:
To configure Path Cost of CIST / MST Normal Port Configuration for specific
interface
Example:

106

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

To enable Path Cost (32) of CIST / MST Normal Port Configuration (CIST) for
GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # spanning-tree mst 0 port-priority 32
spanning-tree restricted-role
Command:
spanning-tree restricted-role
spanning-tree
restricted-role

Spanning Tree protocol
Port role is restricted (never root port)

Default:
Disabled
Usage Guide:
To enable Restricted-role of CIST Normal Port Configuration for specific
interface
Example:
To enable Restricted-role of CIST Normal Port Configuration for
GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # spanning-tree restricted-role
spanning-tree restricted-tcn
Command:
spanning-tree restricted-tcn
spanning-tree
restricted-tcn

Spanning Tree protocol
Restrict topology change notifications

Default:
Disabled
Usage Guide:
To enable Restrict topology change notifications of CIST Normal Port
Configuration for specific interface
Example:
To enable Restrict topology change notifications of CIST Normal Port
Configuration for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # spanning-tree restricted-tcn
speed
Command:

NS3500-24T-4C Managed Switch Command Guide

107

Chapter 4: Commands for CLI configuration

speed [10 | 100 | 1000 | 10g | auto]
speed

Configures interface speed. If you use 10, 100, or 1000 keywords with
the auto keyword the port will only advertise the specified speeds.
10
10Mbps
100 100Mbps
1000 1Gbps
10g 10Gbps
auto Auto negotiation
Default:
Auto
Usage Guide:
To configure line speed for specific interface
Example:
To configure line speed (1Gbps) for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # speed 1000
switchport access vlan
Command:
switchport access vlan 
switchport Switching mode characteristics
access
Set access mode characteristics of the interface
vlan Set VLAN when interface is in access mode
 VLAN ID of the VLAN when this port is in access mode
Default:
1
Usage Guide:
To configure access VLAN ID for specific interface
Example:
To configure access VLAN ID (5) for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # switchport access vlan 5
switchport forbidden vlan add
Command:
switchport forbidden vlan add 
switchport Switching mode characteristics
forbidden Adds or removes forbidden VLANs from the current list of forbidden
VLANs
vlan
Add or modify VLAN entry in forbidden table.
add
Add to existing list.
 VLAN IDs
108

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Default:
1
Usage Guide:
To add forbidden VLAN ID for specific interface
Example:
To add forbidden VLAN ID (5) for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # switchport forbidden vlan add 5
switchport forbidden vlan remove
Command:
switchport forbidden vlan remove 
switchport Switching mode characteristics
forbidden Adds or removes forbidden VLANs from the current list of forbidden
VLANs
vlan Add or modify VLAN entry in forbidden table.
remove Remove from existing list.
 VLAN IDs
Default:
1
Usage Guide:
To remove forbidden VLAN ID for specific interface
Example:
To remove forbidden VLAN ID (5) for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # switchport forbidden vlan remove 5
switchport hybrid acceptable-frame-type
Command:
switchport hybrid acceptable-frame-type all | tagged |
untagged
switchport Switching mode characteristics
hybrid
Change PVID for hybrid port
acceptable-frame-type Set acceptable frame type on a port.
all
Allow all frames
tagged
Allow only tagged frames
untagged Allow only untagged frames
Default:
All
Usage Guide:
To configure acceptable-frame-type of Hybrid VLAN for specific interface

NS3500-24T-4C Managed Switch Command Guide

109

Chapter 4: Commands for CLI configuration

Example:
To configure acceptable-frame-type (tagged) of Hybrid VLAN for
GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # switchport hybrid acceptable-frame-type
tagged
switchport hybrid allowed vlan
Command:
switchport hybrid allowed vlan [all | none | add  |
remove  | except ]
switchport
Switching mode characteristics
hybrid
Change PVID for hybrid port
allowed
Set allowed VLAN characteristics when interface is in hybrid mode
 VLAN IDs of the allowed VLANs when this port is in hybrid mode
add
Add VLANs to the current list
all
All VLANs
except
All VLANs except the following
none
No VLANs
remove
Remove VLANs from the current list
Default:
All
Usage Guide:
To configure VLAN list of Hybrid VLAN for specific interface
Example:
To configure VLAN list (None) of Hybrid VLAN for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # switchport hybrid allowed vlan none
switchport hybrid egress-tag
Command:
switchport hybrid egress-tag [none | all | all except-native]
switchport Switching mode characteristics
hybrid
Change PVID for hybrid port
egress-tag Egress VLAN tagging configuration
all Tag all frames
none No egress tagging
except-native Tag all frames except frames classified to native VLAN of the
hybrid port
Default:
Untagged Port VLAN
Usage Guide:
To configure Egress Tagging VLAN mode for specific interface

110

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Example:
To configure Egress Tagging VLAN mode (None) for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # switchport hybrid egress-tag none
switchport hybrid ingress-filtering
Command:
switchport hybrid ingress-filtering
switchport Switching mode characteristics
hybrid
Change PVID for hybrid port
ingress-filtering VLAN Ingress filter configuration
Default:
Enabled
Usage Guide:
To enable Ingress-filtering with Hybrid VLAN mode for specific interface
Example:
To enable Ingress-filtering with Hybrid VLAN mode for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # switchport hybrid ingress-filtering
switchport hybrid native vlan
Command:
switchport hybrid native vlan 
switchport
Switching mode characteristics
hybrid
Change PVID for hybrid port
native
Set native VLAN
vlan Set native VLAN when interface is in hybrid mode
 VLAN ID of the native VLAN when this port is in hybrid mode
Default:
1
Usage Guide:
To configure PVID in Hybrid VLAN mode for specific interface
Example:
To enable PVID (5) in Hybrid VLAN mode for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # switchport hybrid native vlan 5

NS3500-24T-4C Managed Switch Command Guide

111

Chapter 4: Commands for CLI configuration

switchport hybrid port-type
Command:
switchport hybrid port-type c-port | s-custom-port | s-port |
unaware
switchport
Switching mode characteristics
hybrid
Change PVID for hybrid port
port-type Set port type
c-port
Customer port
s-custom-port Custom Provider port
s-port
Provider port
unaware
Port in not aware of VLAN tags.
Default:
C-port
Usage Guide:
To configure Port type in Hybrid VLAN mode for specific interface
Example:
To enable Port type (Unaware) in Hybrid VLAN mode for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # switchport hybrid port-type unaware
switchport mode
Command:
switchport mode c-port | s-custom-port | s-port | unaware
switchport Switching mode characteristics
mode
Set mode of the interface
port-type
Set port type
c-port
Customer port
s-custom-port Custom Provider port
s-port
Provider port
unaware
Port in not aware of VLAN tags.
Default:
unaware
Usage Guide:
To configure VLAN mode for specific interface
Example:
To configure VLAN mode (trunk) for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # switchport mode trunk
switchport vlan ip-subnet
Command:
switchport vlan ip-subnet id <1-128>  vlan


112

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

switchport Switching mode characteristics
vlan
VLAN commands
ip-subnet VCL IP Subnet-based VLAN configuration.
id id keyword
<1-128> Unique VCE ID for each VCL entry (1-128)
 Source IP address and mask (Format:
xx.xx.xx.xx/mm.mm.mm.mm).
vlan vlan keyword
 VLAN ID required for the group to VLAN mapping (Range: 1-4095)
Default:
None
Usage Guide:
To configure IP Subnet-based VLAN for specific interface
Example:
To configure IP Subnet-based VLAN as below table for GigabitEthernet X/X

Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # switchport vlan ip-subnet id 1
192.168.1.0/255.255.255.0 vlan 5
switchport vlan mac
Command:
switchport vlan mac  vlan 
switchport
Switching mode characteristics
vlan
VLAN commands
mac
MAC-based VLAN commands
 48 bit unicast MAC address: xx:xx:xx:xx:xx:xx
vlan vlan keyword
 VLAN ID required for the group to VLAN mapping (Range: 1-4095)
Default:
None
Usage Guide:
To configure MAC-based VLAN for specific interface
Example:
To configure MAC-based VLAN as below table for GigabitEthernet X/X

Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # switchport vlan mac 00:55:44:33:22:11 vlan 5

NS3500-24T-4C Managed Switch Command Guide

113

Chapter 4: Commands for CLI configuration

switchport vlan mapping
Command:
switchport vlan mapping 
switchport
Switching mode characteristics
vlan
VLAN commands
mapping
Maps an interface to a VLAN translation group.
 Group id
Default:
None
Usage Guide:
To configure Group mapping Table for specific interface
Example:
To configure Group mapping (Group 25) for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # switchport vlan mapping 25
switchport vlan protocol group
Command:
switchport vlan protocol group  vlan 
switchport
Switching mode characteristics
vlan
VLAN commands
protocol Protocol-based VLAN commands
group Protocol-based VLAN group commands
 Group Name (Range: 1 - 16 characters)
vlan vlan keyword
 VLAN ID required for the group to VLAN mapping (Range: 1-4095)
Default:
None
Usage Guide:
To configure VLAN protocol group for specific interface
Example:
To configure VLAN protocol group as tabled below for GigabitEthernet X/X

Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # switchport vlan protocol group 8081 vlan 5
switchport voice vlan discovery-protocol
Command:
switchport voice vlan discovery-protocol both | lldp | oui
switchport

114

Switching mode characteristics

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

voice Voice appliance attributes
vlan Vlan for voice traffic
discovery-protocol Set Voice VLAN port discovery protocol
both Detect telephony device by OUI address and LLDP
lldp Detect telephony device by LLDP
oui Detect telephony device by OUI address
Default:
OUI
Usage Guide:
To configure Discovery-protocol in the Voice VLAN for specific interface
Example: To configure Discovery-protocol (LLDP) in the Voice VLAN for
GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # switchport voice vlan discovery-protocol
lldp
switchport voice vlan mode
Command:
switchport voice vlan mode auto | disable | force
switchport Switching mode characteristics
voice
Voice appliance attributes
vlan Vlan for voice traffic
mode
Set Voice VLAN port mode
auto
Enable auto detect mode
disable disjoin Voice VLAN
force
Force to join Voice VLAN
Default:
Disabled
Usage Guide:
To configure Voice VLAN mode for specific interface
Example:
To configure Voice VLAN mode (Auto) for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # switchport voice vlan mode auto
switchport voice vlan security
Command:
switchport voice vlan security
switchport Switching mode characteristics
voice
Voice appliance attributes
vlan Vlan for voice traffic
security Enable Voice VLAN port security mode

NS3500-24T-4C Managed Switch Command Guide

115

Chapter 4: Commands for CLI configuration

Default:
Disabled
Usage Guide:
To enable Voice VLAN security for specific interface
Example:
To enable Voice VLAN security for GigabitEthernet X/X
Switch# configure terminal
Switch (config)# interface GigabitEthernet X/X
Switch (config-if) # switchport voice vlan security

interface vlan
Command:
interface vlan 
vlan
VLAN interface configurations
 List of VLAN interface numbers, 1~4095
Default:
N/A
Usage Guide:
To enter the VLAN interface mode.
Example:
To enter the VLAN 1 interface mode
Switch# configure terminal
Switch (config)# interface vlan 1
Switch (config-if-vlan)#
do
Command:
do < exec commands >
do

To run exec commands in config mode

Default:
N/A
Usage Guide:
To run exec commands in configure terminal mode
Example:
To run “show aaa” in configure terminal mode.
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# do show aaa
console : local
telnet : local
ssh : local

116

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

http

: local

end
Command:
end
end

Go back to EXEC mode

Default:
Auto
Usage Guide:
To back to EXEC mode
Example:
To back to EXEC mode
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# end
Switch#
exit
Command:
exit
exit

Exit from current mode

Default:
None
Usage Guide:
To exit current mode
Example:
To exit current mode.
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# exit
Switch (config)#
ip address
Command:
ip address  
ip
Interface Internet Protocol config commands
address Address configuraton
 IP address
 IP netmask
Default:
None

NS3500-24T-4C Managed Switch Command Guide

117

Chapter 4: Commands for CLI configuration

Usage Guide:
To configure IP address mode for specific VLAN
Example:
To configure IP address mode (192.168.1.10/24) for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ip address 192.168.1.10 255.255.255.0

ip address dhcp
Command:
ip address dhcp
ip
Interface Internet Protocol config commands
address Address configuraton
dhcp
Enable DHCP
Default:
None
Usage Guide:
To configure IP address mode for specific VLAN
Example:
To configure IP address mode (DHCP) for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ip address dhcp
ip address dhcp fallback
Command:
ip address dhcp fallback  
ip
Interface Internet Protocol config commands
address Address configuraton
dhcp
Enable DHCP
 DHCP fallback address
 DHCP fallback netmask
Default:
None
Usage Guide:
To configure DHCP fallback IP address for specific VLAN
Example:
To configure DHCP fallback IP address (192.168.1.10/24) for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ip address dhcp fallback 192.168.1.10

118

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

255.255.255.0
ip dhcp server
Command:
ip dhcp server
ip
Interface Internet Protocol config commands
dhcp Configure DHCP server parameters
server Enable DHCP server per VLAN
Default:
None
Usage Guide:
To enable IPv4 DHCP Server for specific VLAN
Example:
To enable IPv4 DHCP Server for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ip dhcp server
ip igmp snooping
Command:
ip igmp snooping
ip
Interface Internet Protocol config commands
igmp
Internet Group Management Protocol
snooping Snooping IGMP
Default:
Disabled
Usage Guide:
To enable IGMP snooping for specific VLAN
Example:
To enable IGMP snooping for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ip igmp snooping
ip igmp snooping compatibility
Command:
ip igmp snooping compatibility auto | v1 | v2 | v3
ip
Interface Internet Protocol config commands
igmp
Internet Group Management Protocol

NS3500-24T-4C Managed Switch Command Guide

119

Chapter 4: Commands for CLI configuration

snooping Snooping IGMP
compatibility Interface compatibility
auto Compatible with IGMPv1/IGMPv2/IGMPv3
v1
Forced IGMPv1
v2
Forced IGMPv2
v3
Forced IGMPv3
Default:
Auto
Usage Guide:
To configure IGMP snooping version for specific VLAN
Example:
To configure IGMP snooping V2 for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ip igmp snooping compatibility v2
ip igmp snooping last-member-query-interval
Command:
ip igmp snooping last-member-query-interval 
ip
Interface Internet Protocol config commands
igmp
Internet Group Management Protocol
snooping Snooping IGMP
last-member-query-interval Last Member Query Interval in tenths of seconds
 0 - 31744 tenths of seconds
Default:
10
Usage Guide:
To configure Last-member-query-interval of IGMP snooping for specific VLAN
Example:
To configure Last-member-query-interval (100 seconds) of IGMP snooping for
VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ip igmp snooping last-member-queryinterval 1000
ip igmp snooping priority
Command:
ip igmp snooping priority 
ip
Interface Internet Protocol config commands
igmp
Internet Group Management Protocol
snooping Snooping IGMP

120

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

priority
Interface CoS priority
 CoS priority ranges from 0 to 7
Default:
0
Usage Guide:
To configure CoS priority of IGMP snooping for specific VLAN
Example:
To configure CoS priority (5) of IGMP snooping for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ip igmp snooping priority 5
ip igmp snooping querier address
Command:
ip igmp snooping querier address 
ip
Interface Internet Protocol config commands
igmp
Internet Group Management Protocol
snooping Snooping IGMP
querier
IGMP Querier configuration
address IGMP Querier address configuration
 A valid IPv4 unicast address
Default:
0.0.0.0
Usage Guide:
To configure Querier address of IGMP snooping for specific VLAN
Example:
To configure Querier address (192.168.1.15) of IGMP snooping for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ip igmp snooping querier address
192.168.1.15
ip igmp snooping querier election
Command:
ip igmp snooping querier election
ip
Interface Internet Protocol config commands
igmp
Internet Group Management Protocol
snooping Snooping IGMP
querier
IGMP Querier configuration
election Act as an IGMP Querier to join Querier-Election
Default:
Enabled
Usage Guide:

NS3500-24T-4C Managed Switch Command Guide

121

Chapter 4: Commands for CLI configuration

To enable Querier-election of IGMP snooping for specific VLAN
Example:
To enable Querier-election of IGMP snooping for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ip igmp snooping querier election
ip igmp snooping query-interval
Command:
ip igmp snooping query-interval 
ip
Interface Internet Protocol config commands
igmp
Internet Group Management Protocol
snooping Snooping IGMP
query-interval
Query Interval in seconds
 1 - 31744 seconds
Default:
125
Usage Guide:
To configure Querier-interval of IGMP snooping for specific VLAN
Example:
To configure Querier-interval (600 seconds) of IGMP snooping for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ip igmp snooping query-interval 600
ip igmp snooping query-max-response-time
Command:
ip igmp snooping query-max-response-time 
ip
Interface Internet Protocol config commands
igmp
Internet Group Management Protocol
snooping Snooping IGMP
query-max-response-time Query Response Interval in tenths of seconds
 0 - 31744 tenths of seconds
Default:
125
Usage Guide:
To configure Querier-interval of IGMP snooping for specific VLAN
Example:
To configure Querier-interval (60 seconds) of IGMP snooping for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ip igmp snooping query-max-response-time 600

122

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

ip igmp snooping robustness-variable
Command:
ip igmp snooping robustness-variable 
ip
Interface Internet Protocol config commands
igmp
Internet Group Management Protocol
snooping Snooping IGMP
robustness-variable
Robustness Variable
 Packet loss tolerance count from 1 to 255
Default:
2
Usage Guide:
To configure Robustness Variable of IGMP snooping for specific VLAN
Example:
To configure Robustness Variable (88) of IGMP snooping for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ip igmp snooping robustness-variable
88
ip igmp snooping unsolicited-report-interval
Command:
ip igmp snooping unsolicited-report-interval 
ip
Interface Internet Protocol config commands
igmp
Internet Group Management Protocol
snooping Snooping IGMP
robustness-variable Robustness Variable
 0 - 31744 seconds
Default:
1
Usage Guide:
To configure Unsolicited-Report-Interval of IGMP snooping for specific VLAN
Example:
To configure Unsolicited-Report-Interval (99 seconds) of IGMP snooping for
VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ip igmp snooping unsolicited-reportinterval 99
ipv6 address
Command:
Ipv6 address X:X:X:X::X/<0-128>
ipv6

IPv6 configuration commands

NS3500-24T-4C Managed Switch Command Guide

123

Chapter 4: Commands for CLI configuration

address Configure the IPv6 address of an interface
X:X:X:X::X/<0-128> IPv6 prefix x:x::y/z
Default:
None
Usage Guide:
To configure IPv6 address for specific VLAN
Example:
To configure IPv6 address (2001::7788/64) for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ipv6 address 2001::7788/64
ipv6 mld snooping
Command:
ipv6 mld snooping
ipv6 IPv6 configuration commands
mld
Multicast Listener Discovery
snooping Snooping MLD
Default:
Disabled
Usage Guide:
To enable MLD snooping for specific VLAN
Example:
To enable MLD snooping for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ipv6 mld snooping
ipv6 mld snooping compatibility
Command:
ipv6 mld snooping compatibility auto | v1 | v2
ipv6 IPv6 configuration commands
mld
Multicast Listener Discovery
snooping Snooping MLD
compatibility Interface compatibility
auto Compatible with MLDv1/MLDv2
v1
Forced MLDv1
v2
Forced MLDv2
Default:
Auto
Usage Guide:
To configure MLD snooping version for specific VLAN
Example:

124

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

To configure MLD snooping V2 for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ipv6 mld snooping compatibility v2
ipv6 mld snooping last-member-query-interval
Command:
ipv6 mld snooping last-member-query-interval 
ipv6 IPv6 configuration commands
mld
Multicast Listener Discovery
snooping Snooping MLD
last-member-query-interval Last Member Query Interval in tenths of seconds
 0 - 31744 tenths of seconds
Default:
10
Usage Guide:
To configure Last-member-query-interval of MLD snooping for specific VLAN
Example:
To configure Last-member-query-interval (100 seconds) of MLD snooping for
VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ipv6 mld snooping last-member-queryinterval 1000
ipv6 mld snooping priority
Command:
ipv6 mld snooping priority 
ipv6 IPv6 configuration commands
mld
Multicast Listener Discovery
snooping Snooping MLD
priority
Interface CoS priority
 CoS priority ranges from 0 to 7
Default:
0
Usage Guide:
To configure CoS priority of MLD snooping for specific VLAN

NS3500-24T-4C Managed Switch Command Guide

125

Chapter 4: Commands for CLI configuration

Example:
To configure CoS priority (5) of MLD snooping for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ipv6 mld snooping priority 5
ipv6 mld snooping querier election
Command:
ipv6 mld snooping querier election
ipv6 IPv6 configuration commands
mld
Multicast Listener Discovery
snooping Snooping MLD
querier
MLD Querier configuration
election Act as an MLD Querier to join Querier-Election
Default:
Enabled
Usage Guide:
To enable Querier-election of MLD snooping for specific VLAN
Example:
To enable Querier-election of MLD snooping for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ipv6 mld snooping querier election
ipv6 mld snooping query-interval
Command:
ipv6 mld snooping query-interval 
ipv6 IPv6 configuration commands
mld
Multicast Listener Discovery
snooping Snooping MLD
query-interval
Query Interval in seconds
 1 - 31744 seconds
Default:
125
Usage Guide:
To configure Querier-interval of MLD snooping for specific VLAN
Example:
To configure Querier-interval (600 seconds) of MLD snooping for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ipv6 mld snooping query-interval 600

126

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

ipv6 mld snooping query-max-response-time
Command:
ipv6 mld snooping query-max-response-time 
ipv6 IPv6 configuration commands
mld
Multicast Listener Discovery
snooping Snooping MLD
query-max-response-time
Query Response Interval in tenths of seconds
 0 - 31744 tenths of seconds
Default:
125
Usage Guide:
To configure Querier-interval of MLD snooping for specific VLAN
Example:
To configure Querier-interval (60 seconds) of MLD snooping for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ipv6 mld snooping query-maxresponse-time 600
ipv6 mld snooping robustness-variable
Command:
ipv6 mld snooping robustness-variable 
ipv6 IPv6 configuration commands
mld
Multicast Listener Discovery
snooping Snooping MLD
robustness-variable Robustness Variable
 Packet loss tolerance count from 1 to 255
Default:
2
Usage Guide:
To configure Robustness Variable of MLD snooping for specific VLAN
Example:
To configure Robustness Variable (88) of MLD snooping for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ipv6 mld snooping robustness-variable
88
ipv6 mld snooping unsolicited-report-interval
Command:
ipv6 mld snooping unsolicited-report-interval 
ipv6 IPv6 configuration commands
mld
Multicast Listener Discovery

NS3500-24T-4C Managed Switch Command Guide

127

Chapter 4: Commands for CLI configuration

snooping Snooping MLD
robustness-variable Robustness Variable
 0 - 31744 seconds
Default:
1
Usage Guide:
To configure Unsolicited-Report-Interval of MLD snooping for specific VLAN
Example:
To configure Unsolicited-Report-Interval (99 seconds) of MLD snooping for
VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# ipv6 mld snooping unsolicited-reportinterval 99
no
Command:
no
no

Negate a command or set its defaults

Default:
N/A
Usage Guide:
To default the function for specific interface
Example:
To disable the function (ip address dhcp) for VLAN X
Switch# configure terminal
Switch (config)# interface vlan X
Switch (config-if-vlan)# no ip address dhcp

ip arp inspection
Command:
ip arp inspection
ip
Internet Protocol
arp
Address Resolution Protocol
inspection ARP inspection
Default:
N/A
Usage Guide:
To enable ARP inspection
Example:
To enable ARP inspection

128

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# ip arp inspection

ip arp inspection entry interface
Command:
ip arp inspection entry interface [10GigabitEthernet |
GigabitEthernet]   
ip
Internet Protocol
arp
Address Resolution Protocol
inspection ARP inspection
entry
arp inspection entry
interface arp inspection entry interface config
GigabitEthernet
1 Gigabit Ethernet Port
10GigabitEthernet 10 Gigabit Ethernet Port
 Select a VLAN id to configure
 Select a MAC address to configure
 Select an IP Address to configure
Default:
N/A
Usage Guide:
To configure Static ARP Inspection Table.
Example:
To configure Static ARP Inspection Table as below table.

Switch# configure terminal
Switch (config)# ip arp inspection entry interface
GigabitEthernet 1/1 1 00:11:22:33:44:55 192.168.0.18

ip arp inspection translate
Command:
ip arp inspection translate
ip
Internet Protocol
arp
Address Resolution Protocol
inspection ARP inspection
translate arp inspection translate all entries
Default:
N/A
Usage Guide:
To translate dynamic entries into static ARP inspection table.
Example:
To translate dynamic entries into static ARP inspection table.

NS3500-24T-4C Managed Switch Command Guide

129

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# ip arp inspection translate
ARP Inspection:
Translate 1 dynamic entries into static entries.

ip arp inspection translate interface
Command:
ip arp inspection translate interface [10GigabitEthernet |
GigabitEthernet]   
ip
Internet Protocol
arp
Address Resolution Protocol
inspection ARP inspection
translate arp inspection translate all entries
interface arp inspection entry interface config
GigabitEthernet
1 Gigabit Ethernet Port
10GigabitEthernet 10 Gigabit Ethernet Port
 Select a VLAN id to configure
 Select a MAC address to configure
 Select an IP Address to configure
Default:
N/A
Usage Guide:
To translate dynamic entries into static ARP inspection table for specific
interface.
Example:
To translate below dynamic entries into static ARP inspection table for
GigabitEthernet 1/1.

Switch# configure terminal
Switch (config)# ip arp inspection translate interface
GigabitEthernet 1/1 1 00:11:22:33:44:55 192.168.0.18

ip arp inspection vlan
Command:
ip arp inspection vlan  logging all | deny | permit
ip
Internet Protocol
arp
Address Resolution Protocol
inspection ARP inspection
vlan
arp inspection vlan setting
 arp inspection vlan list
logging ARP inspection vlan logging mode config
all
log all entries
deny
log denied entries
130

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

permit

log permitted entries

Default:
N/A
Usage Guide:
To configure VLAN mode of ARP inspection.
Example:
To configure VLAN mode (VLAN 1, Log type: Permit) of ARP inspection.
Switch# configure terminal
Switch (config)# ip arp inspection vlan 1 logging permit

ip dhcp excluded-address
Command:
ip dhcp excluded-address 
ip
Internet Protocol
dhcp
Dynamic Host Configuration Protocol
excluded-address Prevent DHCP from assigning certain addresses
 Low IP address
Default:
N/A
Usage Guide:
To configure excluded IP range of DHCP Server.
Example:
To configure excluded IP range (192.168.0.100~192.168.0.101) of DHCP Server.
Switch# configure terminal
Switch (config)# ip dhcp excluded-address 192.168.0.100
192.168.0.101

ip dhcp pool
Command:
ip dhcp pool 
ip
Internet Protocol
dhcp
Dynamic Host Configuration Protocol
pool
Configure DHCP address pools
 Pool name in 32 characters
Default:
N/A
Usage Guide:
To create a DHCP pool.
Example:
To create a DHCP pool (Name: IFSbestswitch).

NS3500-24T-4C Managed Switch Command Guide

131

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)#
broadcast
Command:
broadcast 
broadcast


Broadcast address in use on the client's subnet
Broadcast IP address

Default:
None
Usage Guide:
To configure Broadcast IP address (DHCP option 28) of DHCP Server
Example:
To configure Broadcast IP address (192.168.0.66) of DHCP Server for pool
“IFSbestswitch”
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# broadcast 192.168.0.66
client-identifier fqdn
Command:
client-identifier fqdn 
client-identifier
Client identifier
fqdn
FQDN type of client identifier
 FQDN in 128 characters
Default:
None
Usage Guide:
To configure FQDN of DHCP Server
Example:
To configure FQDN (123) of DHCP Server for pool “IFSbestswitch”
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# client-identifier fqdn 123
client-identifier mac-address
Command:
client-identifier mac-address 
client-identifier Client identifier
mac-address MAC address type of client identifier
 MAC address of client

132

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Default:
None
Usage Guide:
To configure Bind IP to MAC of DHCP Server
Example:
To configure Bind IP to MAC (00:11:22:33:44:55) of DHCP Server for pool
“IFSbestswitch”
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# client-identifier mac-address
00:11:22:33:44:55
client-name
Command:
client-name
client-name

Client host name

Default:
None
Usage Guide:
To configure Client-name of DHCP Server
Example:
To configure Client-name (555) of DHCP Server for pool “IFSbestswitch”
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# client-name 555
default-router
Command:
default-router 
default-router Default routers
 Router's IP address
Default:
None
Usage Guide:
To configure Default Gateway of DHCP Server
Example:
To configure Default Gateway (192.168.0.1) of DHCP Server for pool
“IFSbestswitch”
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# default-router 192.168.0.1

NS3500-24T-4C Managed Switch Command Guide

133

Chapter 4: Commands for CLI configuration

dns-server
Command:
dns-server 
dns-server DNS servers
 Server's IP address
Default:
None
Usage Guide:
To configure DNS Server of DHCP Server
Example:
To configure DNS Server (168.95.1.1, 8.8.8.8) of DHCP Server for pool
“IFSbestswitch”
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# dns-server 168.95.1.1 8.8.8.8
do
Command:
do < exec commands >
do

To run exec commands in config mode

Default:
N/A
Usage Guide:
To run exec commands
Example:
To run “show aaa”.
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# do show aaa
console : local
telnet : local
ssh : local
http : local
domain-name
Command:
domain-name 
domain-name Domain name
 Domain name
Default:
None
Usage Guide:

134

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

To configure Domain Name of DHCP Server
Example:
To configure Domain Name (interlogix.com) of DHCP Server for pool
“IFSbestswitch”
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# domain-name interlogix.com
end
Command:
end
end

Go back to EXEC mode

Default:
Auto
Usage Guide:
To back to EXEC mode
Example:
To back to EXEC mode
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# end
Switch#
exit
Command:
exit
exit

Exit from current mode

Default:
None
Usage Guide:
To exit current mode
Example:
To exit current mode.
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# exit
Switch (config)#
hardware-address
Command:
hardware-address 

NS3500-24T-4C Managed Switch Command Guide

135

Chapter 4: Commands for CLI configuration

hardware-address
Client hardware address
 Client MAC address
Default:
None
Usage Guide:
To configure MAC address of DHCP Server while the pool is in the host type.
Example:
To configure MAC address (00:11:22:33:44:55) of DHCP Server for pool
“IFSbestswitch” while the pool is in the host type.
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# hardware-address 00:11:22:33:44:55
host
Command:
host  
host
Client IP address and mask
 Network number
 Network mask in dotted-decimal notation, excluding
255.255.255.255
Default:
None
Usage Guide:
To configure Host IP address of DHCP Server.
Example:
To configure Host IP address (192.168.1.10/24) of DHCP Server for pool
“IFSbestswitch”.
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# host 192.168.1.10 255.255.255.0
lease
Command:
lease <0-365> <0-23> <0-59> | infinite
lease
<0-365>
<0-23>
<0-59>
infinite

Address lease time
Days
Hours
Minutes
Infinite lease

Default:
1 day
Usage Guide:
To configure Lease Time of DHCP Server.

136

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Example:
To configure Lease Time (119 minutes) of DHCP Server for pool “IFSbestswitch”.
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# lease 0 1 59
netbios-name-server
Command:
netbios-name-server 
netbios-name-server NetBIOS (WINS) name servers
 Server's IP address
Default:
None
Usage Guide:
To configure NetBIOS Name Server of DHCP Server.
Example:
To configure NetBIOS Name Server (192.168.1.10) of DHCP Server for pool
“IFSbestswitch”.
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# netbios-name-server 192.168.1.10
netbios-node-type
Command:
netbios-node-type b-node | h-node | m-node | p-node
netbios-node-type
NetBIOS node type
b-node Broadcast node
h-node Hybrid node
m-node Mixed node
p-node Peer-to-peer node
Default:
None
Usage Guide:
To configure NetBIOS node type of DHCP Server.
Example:
To configure NetBIOS node type (B-node) of DHCP Server for pool
“IFSbestswitch”.
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# netbios-node-type b-node

NS3500-24T-4C Managed Switch Command Guide

137

Chapter 4: Commands for CLI configuration

netbios-scope
Command:
netbios-scope 
netbios-scope NetBIOS scope
 Netbios scope identifier, in 128 characters
Default:
None
Usage Guide:
To configure NetBIOS scope of DHCP Server.
Example:
To configure NetBIOS scope (IFS) of DHCP Server for pool “IFSbestswitch”.
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# netbios-scope IFS
network
Command:
network  
network
Network number and mask
 Network number
 Network mask in dotted-decimal notation, excluding
255.255.255.255
Default:
None
Usage Guide:
To configure Network IP address of DHCP Server.
Example:
To configure Network IP address (192.168.1.11/24) of DHCP Server for pool
“IFSbestswitch”.
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# network 192.168.0.11 255.255.255.0
nis-domain-name
Command:
nis-domain-name 
nis-domain-name
NIS domain name
 Domain name
Default:
None

138

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Usage Guide:
To configure NIS Domain Name of DHCP Server
Example:
To configure NIS Domain Name (interlogix.com) of DHCP Server for pool
“IFSbestswitch”
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# nis-domain-name interlogix.com
nis-server
Command:
nis-server 
nis-server


Network information servers
Server's IP address

Default:
None
Usage Guide:
To configure NIS Server of DHCP Server
Example:
To configure NIS Server (1.1.1.1) of DHCP Server for pool “IFSbestswitch”
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# nis-server 1.1.1.1
no
Command:
no
no

Negate a command or set its defaults

Default:
N/A
Usage Guide:
To default the function
Example:
To disable the function (nis-domain-name interlogix.com) for pool
“IFSbestswitch”
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# no nis-domain-name interlogix.com
ntp-server
Command:
ntp-server 

NS3500-24T-4C Managed Switch Command Guide

139

Chapter 4: Commands for CLI configuration

ntp-server NTP servers
 Server's IP address
Default:
None
Usage Guide:
To configure NTP Server of DHCP Server
Example:
To configure NTP Server (1.1.1.1) of DHCP Server for pool “IFSbestswitch”
Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# ntp-server 1.1.1.1
vendor
Command:
vendor class-identifier <”0x “> specific-info 
vendor
Vendor configuration
class-identifier Vendor class identifier
"<0x >" Class identifier in 64 characters
specific-info Vendor specific information
 Hex values in 64 octets
Default:
None
Usage Guide:
To configure Vendor ID and info of DHCP Server
Example:
To configure Vendor ID and info as below table of DHCP Server for pool
“IFSbestswitch”

Switch# configure terminal
Switch (config)# ip dhcp pool IFSbestswitch
Switch (config-dhcp-pool)# vendor class-identifier "0x8"
specific-info 0x8

ip dns proxy
Command:
ip dns proxy
ip
Internet Protocol
dns
Domain Name System
proxy DNS proxy service
Default:
Disabled

140

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Usage Guide:
To enable DNS proxy.
Example:
To enable DNS proxy.
Switch# configure terminal
Switch (config)# ip dns proxy

ip helper-address
Command:
ip helper-address 
ip
Internet Protocol
helper-address DHCP relay server
 IP address of the DHCP relay server
Default:
None
Usage Guide:
To configure IP address of DHCP.
Example:
To configure IP address (1.1.1.1) of DHCP.
Switch# configure terminal
Switch (config)# ip helper-address 1.1.1.1

ip http secure-redirect
Command:
ip http secure-redirect
ip
Internet Protocol
http
Hypertext Transfer Protocol
secure-redirect Secure HTTP web redirection
Default:
Disabled
Usage Guide:
To redirect WebUI from HTTP to HTTPs
Example:
To redirect WebUI from HTTP to HTTPs
Switch# configure terminal
Switch (config)# ip http secure-redirect

NS3500-24T-4C Managed Switch Command Guide

141

Chapter 4: Commands for CLI configuration

ip http secure-server
Command:
ip http secure-server
ip
Internet Protocol
http
Hypertext Transfer Protocol
secure-server
Secure HTTP web server
Default:
Disabled
Usage Guide:
To enable HTTPs WebUI.
Example:
To enable HTTPs WebUI.
Switch# configure terminal
Switch (config)# ip http secure-server

ip igmp host-proxy
Command:
ip igmp host-proxy
ip
Internet Protocol
igmp
Internet Group Management Protocol
host-proxy IGMP proxy configuration
Default:
Disabled
Usage Guide:
To enable IGMP Proxy
Example:
To enable IGMP Proxy.
Switch# configure terminal
Switch (config)# ip igmp host-proxy

ip igmp host-proxy leave-proxy
Command:
ip igmp host-proxy leave-proxy
ip
Internet Protocol
igmp
Internet Group Management Protocol
host-proxy IGMP proxy configuration
leave-proxy IGMP proxy for leave configuration
Default:

142

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Disabled
Usage Guide:
To enable IGMP leave-proxy
Example:
To enable IGMP leave-proxy.
Switch# configure terminal
Switch (config)# ip igmp host-proxy leave-proxy

ip igmp snooping
Command:
ip igmp snooping
ip
Internet Protocol
igmp
Internet Group Management Protocol
snooping Snooping IGMP
Default:
Disabled
Usage Guide:
To enable IGMP Snooping.
Example:
To enable IGMP Snooping.
Switch# configure terminal
Switch (config)# ip igmp snooping

ip igmp snooping vlan
Command:
ip igmp snooping vlan 
ip
Internet Protocol
igmp
Internet Group Management Protocol
snooping Snooping IGMP
vlan IGMP VLAN
 VLAN identifier(s): VID
Default:
Disabled
Usage Guide:
To enable IGMP Snooping for specific VLAN.
Example:
To enable IGMP Snooping for VLAN 1.
Switch# configure terminal
Switch (config)# ip igmp snooping vlan 1

NS3500-24T-4C Managed Switch Command Guide

143

Chapter 4: Commands for CLI configuration

ip igmp ssm-range
Command:
ip igmp ssm-range  
ip
Internet Protocol
igmp
Internet Group Management Protocol
ssm-range
IPv4 address range of Source Specific Multicast
 Valid IPv4 multicast address
 VLAN identifier(s): VID
 Prefix length ranges from 4 to 32
Default:
232.0.0.0/8
Usage Guide:
To enable SSM Range of IGMP.
Example:
To enable SSM Range (239.239.239.239/32) of IGMP.
Switch# configure terminal
Switch (config)# ip igmp ssm-range 239.239.239.239 32

ip igmp unknown-flooding
Command:
ip igmp unknown-flooding
ip
Internet Protocol
igmp
Internet Group Management Protocol
unknown-flooding Flooding unregistered IPv4 multicast traffic
Default:
Enabled
Usage Guide:
To flood unregistered IPv4 multicast traffic.
Example:
To flood unregistered IPv4 multicast traffic.
Switch# configure terminal
Switch (config)# ip igmp unknown-flooding

ip name-server
Command:
ip name-server 
ip
Internet Protocol
name-server Domain Name System
 A valid IPv4 unicast address
Default:

144

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Enabled
Usage Guide:
To configure DNS server IP address.
Example:
To configure DNS server IP address (8.8.8.8).
Switch# configure terminal
Switch (config)# ip name-server 8.8.8.8

ip name-server dhcp
Command:
ip name-server dhcp
ip
Internet Protocol
name-server
Domain Name System
dhcp
Dynamic Host Configuration Protocol
Default:
None
Usage Guide:
To configure DNS IP address via DHCP Server.
Example:
To configure DNS IP address via DHCP Server.
Switch# configure terminal
Switch (config)# ip name-server 8.8.8.8

ip name-server dhcp interface vlan
Command:
ip name-server dhcp interface vlan 
ip
Internet Protocol
name-server
Domain Name System
dhcp
Dynamic Host Configuration Protocol
vlan VLAN Interface
 VLAN identifier(s): VID
Default:
None
Usage Guide:
To configure DNS IP address via specific VLAN DHCP Server.
Example:
To configure DNS IP address via specific VLAN 5 DHCP Server.
Switch# configure terminal
Switch (config)# ip name-server dhcp interface vlan 5

NS3500-24T-4C Managed Switch Command Guide

145

Chapter 4: Commands for CLI configuration

ip route
Command:
ip route   
ip
Internet Protocol
route
Add IP route
 Network
 Netmask
 Gateway
Default:
None
Usage Guide:
To configure static route
Example:
To configure static route as below table.

Switch# configure terminal
Switch (config)# ip route 192.168.1.0 255.255.255.0 192.168.0.1

ip routing
Command:
ip routing
ip
Internet Protocol
routing Enable routing for IPv4 and IPv6
Default:
None
Usage Guide:
To enable IP routing
Example:
To enable IP routing
Switch# configure terminal
Switch (config)# ip routing

ip source binding interface
Command:
ip source binding interface 10GigabitEthernet |
GigabitEthernet  

ip
Internet Protocol
source source command

146

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

binding ip source binding
interface ip source binding entry interface config
 Select an IP Address to configure
 Select a subnet mask to configure
Default:
None
Usage Guide:
To enable Static IP Source Guard Table for specific interface
Example:
To enable Static IP Source Guard Table as below table for GigabitEthernet 1/1

Switch# configure terminal
Switch (config)# ip source binding interface GigabitEthernet
1/1 1 192.168.0.77 255.255.255.255

ip ssh
Command:
ip ssh
ip Internet Protocol
ssh Secure Shell
Default:
None
Usage Guide:
To enable SSH service
Example:
To enable SSH service
Switch# configure terminal
Switch (config)# ip ssh

ip verify source
Command:
ip verify source
ip
Internet Protocol
verify verify command
source verify source
Default:
Disabled
Usage Guide:
To enable IP Source Guard
Example:

NS3500-24T-4C Managed Switch Command Guide

147

Chapter 4: Commands for CLI configuration

To enable IP Source Guard
Switch# configure terminal
Switch (config)# ip verify source

ip verify source translate
Command:
ip verify source translate
ip
Internet Protocol
verify verify command
source verify source
translate ip verify source translate all entries
Default:
Disabled
Usage Guide:
To translate dynamic entries to IP Source Guard table
Example:
To translate dynamic entries to IP Source Guard table
Switch# configure terminal
Switch (config)# ip verify source translate

ipmc profile
Command:
ipmc profile
ipmc IPv4/IPv6 multicast configuration
profile IPMC profile configuration
Default:
Disabled
Usage Guide:
To enable IPMC profile
Example:
To enable IPMC profile
Switch# configure terminal
Switch (config)# ipmc profile

ipmc profile 
Command:
ipmc profile 
ipmc

148

IPv4/IPv6 multicast configuration

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

profile IPMC profile configuration
 Profile name
Default:
Disabled
Usage Guide:
To enter IPMC profile mode
Example:
To enter IPMC profile mode (IFS)
Switch# configure terminal
Switch (config)# ipmc profile IFS
Switch (config-ipmc-profile)#
default range
Command:
default range 
default Set a command to its defaults
range A range of IPv4/IPv6 multicast addresses for the profile
 Range entry name
Default:
None
Usage Guide:
To default IPMC Profile Rule for specific IPMC Profile
Example:
To default IPMC Profile Rule (Entry 1) for specific IPMC Profile (IFS)
Switch# configure terminal
Switch (config)# ipmc profile IFS
Switch (config-ipmc-profile)# default range 1
description
Command:
description 
description Additional description about the profile
 Description for the designated IPMC filtering profile
Default:
None
Usage Guide:
To configure description for specific IPMC Profile
Example:
To configure description (999) for specific IPMC Profile (IFS)
Switch# configure terminal
Switch (config)# ipmc profile IFS
Switch (config-ipmc-profile)# description 999

NS3500-24T-4C Managed Switch Command Guide

149

Chapter 4: Commands for CLI configuration

do
Command:
do < exec commands >
do

To run exec commands in config mode

Default:
N/A
Usage Guide:
To run exec commands
Example:
To run “show aaa”.
Switch# configure terminal
Switch (config)# ipmc profile IFS
Switch (config-ipmc-profile)# do show aaa
console : local
telnet : local
ssh : local
http : local
end
Command:
end
end

Go back to EXEC mode

Default:
Auto
Usage Guide:
To back to EXEC mode
Example:
To back to EXEC mode
Switch# configure terminal
Switch (config)# ipmc profile IFS
Switch (config-ipmc-profile)#end
Switch#
exit
Command:
exit
exit

Exit from current mode

Default:
None
Usage Guide:
To exit current mode
Example:

150

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

To exit current mode.
Switch# configure terminal
Switch (config)# ipmc profile IFS
Switch (config-ipmc-profile)# exit
Switch (config)#
no
Command:
no
no

Negate a command or set its defaults

Default:
N/A
Usage Guide:
To default the function.
Example:
To enable the function (description 999).
Switch# configure terminal
Switch (config)# ipmc profile IFS
Switch (config-ipmc-profile)# no description 999
range
Command:
range  deny | permit
description Additional description about the profile
 Range entry name
deny
Deny matching addresses
permit Permit matching addresses
Default:
Deny
Usage Guide:
To configure action of entry for specific IPMC Profile
Example:
To configure action (permit) of entry (1) for specific IPMC Profile (IFS)
Switch# configure terminal
Switch (config)# ipmc profile IFS
Switch (config-ipmc-profile)# range 1 permit

ipv6 mld host-proxy
Command:
ipv6 mld host-proxy
ipv6

IPv6 configuration commands

NS3500-24T-4C Managed Switch Command Guide

151

Chapter 4: Commands for CLI configuration

mld
Multicast Listener Discovery
host-proxy
MLD proxy configuration
Default:
Disabled
Usage Guide:
To enable MLD Proxy
Example:
To enable MLD Proxy.
Switch# configure terminal
Switch (config)# ipv6 mld host-proxy

ipv6 mld host-proxy leave-proxy
Command:
ipv6 mld host-proxy leave-proxy
ipv6
IPv6 configuration commands
mld
Multicast Listener Discovery
host-proxy MLD proxy configuration
leave-proxy MLD proxy for leave configuration
Default:
Disabled
Usage Guide:
To enable MLD leave-proxy
Example:
To enable MLD leave-proxy.
Switch# configure terminal
Switch (config)# ipv6 mld host-proxy leave-proxy

ipv6 mld snooping
Command:
ipv6 mld snooping
ipv6
IPv6 configuration commands
mld
Multicast Listener Discovery
snooping
Snooping MLD
Default:
Disabled
Usage Guide:
To enable MLD Snooping.
Example:
To enable MLD Snooping.

152

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# ipv6 mld snooping

ipv6 mld snooping vlan
Command:
ipv6 mld snooping vlan 
ipv6
IPv6 configuration commands
mld
Multicast Listener Discovery
snooping Snooping MLD
vlan MLD VLAN
 VLAN identifier(s): VID
Default:
Disabled
Usage Guide:
To enable MLD Snooping for specific VLAN.
Example:
To enable MLD Snooping for VLAN 1.
Switch# configure terminal
Switch (config)# ipv6 mld snooping vlan 1

ipv6 mld ssm-range
Command:
ipv6 mld ssm-range  
ipv6
IPv6 configuration commands
mld
Multicast Listener Discovery
ssm-range
IPv6 address range of Source Specific Multicast
 Valid IPv6 multicast address
 Prefix length ranges from 8 to 128
Default:
ff3e:: /96
Usage Guide:
To enable SSM Range of MLD.
Example:
To enable SSM Range (ff3e::7788/128) of MLD.
Switch# configure terminal
Switch (config)# ipv6 mld ssm-range ff3e::7788 128

NS3500-24T-4C Managed Switch Command Guide

153

Chapter 4: Commands for CLI configuration

ipv6 mld unknown-flooding
Command:
ipv6 mld unknown-flooding
ipv6
IPv6 configuration commands
mld
Multicast Listener Discovery
unknown-flooding Flooding unregistered IPv6 multicast traffic
Default:
Enabled
Usage Guide:
To flood unregistered IPv6 multicast traffic.
Example:
To flood unregistered IPv6 multicast traffic.
Switch# configure terminal
Switch (config)# ipv6 mld unknown-flooding

ipv6 route
Command:
Ipv6 route > {, interface vlan
 }
ipv6
IPv6 configuration commands
route
Add IP route
> IPv6 prefix x:x::y/z
 IPv6 unicast address (except link-local address) of next-hop
interface Select an interface to configure
vlan VLAN Interface
 VLAN identifier(s): VID
 IPv6 link-local address of next-hop
Default:
None
Usage Guide:
To configure static route for IPv6
Example 1:
To configure static route as below table for IPv6.

Switch# configure terminal
Switch (config)# ipv6 route 2001::7788/128 2002::1
Example 2:
To configure static route as below table for IPv6.

154

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# ipv6 route 2001::7788/128 interface vlan 1
fe80::1

lacp system-priority
Command:
lacp system-priority <1-65535>
lacp
LACP settings
system-priority System priority
<1-65535> Priority value, lower means higher priority
Default:
32768
Usage Guide:
To configure LACP system-priority.
Example:
To configure LACP system-priority (99).
Switch# configure terminal
Switch (config)# lacp system-priority 99

line
Command:
line { <0~16> | console 0 | vty <0~15> }
line
Configure a terminal line
<0~16> List of line numbers
console Console terminal line
vty
Virtual terminal
Default:
N/A
Usage Guide:
To enter line mode
Example:
To enter line mode (vty 1)
Switch# configure terminal
Switch (config)# line vty 1
Switch (config-line)#
do
Command:
do < exec commands >
do

To run exec commands.

NS3500-24T-4C Managed Switch Command Guide

155

Chapter 4: Commands for CLI configuration

Default:
N/A
Usage Guide:
To run exec commands.
Example:
To run “show aaa”.
Switch# configure terminal
Switch (config)# line vty 1
Switch (config-line)# do show aaa
console : local
telnet : local
ssh : local
http : local
editing
Command:
editing
editing
Enable command line editing
Default:
Enabled
Usage Guide:
To allow user editing command line.
Example:
To allow user editing command line.
Switch# configure terminal
Switch (config)# line vty 1
Switch (config-line)# editing
end
Command:
end
end

Go back to EXEC mode

Default:
None
Usage Guide:
To back to EXEC mode
Example:
To back to EXEC mode
Switch# configure terminal
Switch (config)# line vty 1
Switch (config-line)#end
Switch#

156

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

exec-banner
Command:
exec-banner
exec-banner

Enable the display of the EXEC banner

Default:
Enabled
Usage Guide:
To enable the display of the EXEC banner
Example:
To enable the display of the EXEC banner
Switch# configure terminal
Switch (config)# line vty 1
Switch (config-line)# exec-banner
exec-timeout
Command:
exec-timeout <0-1440>
exec-timeout Set the EXEC timeout
<0-1440> Timeout in minutes
Default:
N/A
Usage Guide:
To configure EXEC timeout
Example:
To configure EXEC timeout (10 minutes)
Switch# configure terminal
Switch (config)# line vty 1
Switch (config-line)# exec-timeout 10
exec-timeout
Command:
exec-timeout <0-1440>
exec-timeout Set the EXEC timeout
<0-1440> Timeout in minutes
Default:
N/A
Usage Guide:
To configure EXEC timeout
Example:
To configure EXEC timeout (10 minutes)
Switch# configure terminal

NS3500-24T-4C Managed Switch Command Guide

157

Chapter 4: Commands for CLI configuration

Switch (config)# line vty 1
Switch (config-line)# exec-timeout 10
exit
Command:
exit
exit

Exit from current mode

Default:
None
Usage Guide:
To exit current mode
Example:
To exit current mode.
Switch# configure terminal
Switch (config)# line vty 1
Switch (config-line)# exit
Switch (config)#
history size
Command:
history size <0-32>
history
Control the command history function
size Set history buffer size
<0-32> Number of history commands, 0 means disable
Default:
None
Usage Guide:
To exit current mode
Example:
To exit current mode.
Switch# configure terminal
Switch (config)# line vty 1
Switch (config-line)# history size 1
length
Command:
length <0 or 3-512>
length
Set number of lines on a screen
<0 or 3-512> Number of lines on screen (0 for no pausing)
Default:
None

158

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Usage Guide:
To configure displayed lines on a screen.
Example:
To configure displayed lines on a screen.
Switch# configure terminal
Switch (config)# line vty 1
Switch (config-line)# length 10
location
Command:
location 
location
Enter terminal location description
 One text line describing the terminal's location
Default:
None
Usage Guide:
To configure description of location.
Example:
To configure description (taiwan) of location.
Switch# configure terminal
Switch (config)# line vty 1
Switch (config-line)# location taiwan
motd-banner
Command:
motd-banner
motd-banner

Enable the display of the MOTD banner

Default:
Enabled
Usage Guide:
To enable MOTD banner.
Example:
To enable MOTD banner..
Switch# configure terminal
Switch (config)# line vty 1
Switch (config-line)# motd-banner
no
Command:
no
no

Negate a command or set its defaults

NS3500-24T-4C Managed Switch Command Guide

159

Chapter 4: Commands for CLI configuration

Default:
N/A
Usage Guide:
To default the function
Example:
To disable the function (motd-banner) for vty 1
Switch# configure terminal
Switch (config)# line vty 1
Switch (config-line)# no motd-banner
privilege level
Command:
privilege level <0-15>
privilege Change privilege level for line
level Assign default privilege level for line
<0-15> Default privilege level for line
Default:
15
Usage Guide:
To configure privilege level
Example:
To configure privilege level (5) for vty 1.
Switch# configure terminal
Switch (config)# line vty 1
Switch (config-line)# privilege level 5
width
Command:
width <0 or 40-512>
width
Set width of the display terminal
<0 or 40-512> Number of characters on a screen line (0 for unlimited width)
Default:
0
Usage Guide:
To configure width of the display terminal.
Example:
To configure width (50) of the display terminal for vty 1.
Switch# configure terminal
Switch (config)# line vty 1
Switch (config-line)# width 50

160

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

lldp holdtime
Command:
lldp holdtime <2-10>
lldp
LLDP configurations.
holdtime Sets LLDP hold time (The neighbor switch will discarded the LLDP
information after "hold time" multiplied with "timer" seconds ).
<2-10> 2-10 seconds
Default:
4
Usage Guide:
To enable LLDP hold time
Example:
To enable LLDP hold time (5)
Switch# configure terminal
Switch (config)# lldp holdtime 5

lldp med datum
Command:
lldp med datum nad83-mllw | nad83-navd88 | wgs84
lldp
LLDP configurations.
med
Media Endpoint Discovery
datum
Datum (geodetic system) type
nad83-mllw
Mean lower low water datum 1983
nad83-navd88 North American vertical datum 1983
wgs84
World Geodetic System 1984
Default:
WGS84
Usage Guide:
To configure Datum type of LLDP
Example:
To configure Datum type (nad83-mllw) of LLDP
Switch# configure terminal
Switch (config)# lldp med datum nad83-mllw

lldp med fast
Command:
lldp med fast <1-10>
lldp
med
fast

LLDP configurations.
Media Endpoint Discovery
Number of times to repeat LLDP frame transmission at fast start.

NS3500-24T-4C Managed Switch Command Guide

161

Chapter 4: Commands for CLI configuration

Default:
4
Usage Guide:
To configure frame transmission time of LLDP
Example:
To configure frame transmission time (6) of LLDP
Switch# configure terminal
Switch (config)# lldp med fast 6

lldp med location-tlv altitude
Command:
lldp med location-tlv altitude [floors ] |
[meters ]
lldp
LLDP configurations.
med Media Endpoint Discovery
location-tlv LLDP-MED Location Type Length Value parameter
altitude
Altitude parameter
floors Specify the altitude in floor.
 Altitude value.
meters Specify the altitude in meters.
Default:
0
Usage Guide:
To configure altitude of LLDP-MED
Example:
To configure altitude (Floors 5) of LLDP-MED
Switch# configure terminal
Switch (config)# lldp med location-tlv altitude floors 5

lldp med location-tlv elin-addr
Command:
lldp med location-tlv elin-addr 
lldp
LLDP configurations.
med
Media Endpoint Discovery
location-tlv LLDP-MED Location Type Length Value parameter
elin-addr Emergency Location Identification Number, (e.g. E911 and others),
such as defined by TIA or NENA.
 ELIN value
Default:
0
Usage Guide:
To configure Emergency Location Identification Number of LLDP-MED

162

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Example:
To configure Emergency Location Identification Number (911) of LLDP-MED
Switch# configure terminal
Switch (config)# lldp med location-tlv elin-addr 911

lldp med location-tlv latitude
Command:
lldp med location-tlv latitude north  | south

lldp
LLDP configurations.
med
Media Endpoint Discovery
location-tlv LLDP-MED Location Type Length Value parameter
latitude
Latitude parameter
north Setting latitude direction to north.
south Setting latitude direction to south
 Latitude degrees (0.0000-90.0000)
Default:
North, 0
Usage Guide:
To configure latitude direction of LLDP-MED
Example:
To configure latitude direction (south, 5) of LLDP-MED
Switch# configure terminal
Switch (config)# lldp med location-tlv latitude south 5

lldp med location-tlv longitude
Command:
lldp med location-tlv longitude east  | west

lldp
LLDP configurations.
med
Media Endpoint Discovery
location-tlv
LLDP-MED Location Type Length Value parameter
longitude Longitude parameter
east Setting longitude direction to east.
west Setting longitude direction to west.
 Longitude degrees (0.0000-180.0000)
Default:
North, 0
Usage Guide:
To configure longitude direction of LLDP-MED
Example:
To configure longitude direction (east, 5) of LLDP-MED
Switch# configure terminal
Switch (config)# lldp med location-tlv longitude east 5

NS3500-24T-4C Managed Switch Command Guide

163

Chapter 4: Commands for CLI configuration

lldp med media-vlan-policy
Command:
lldp med media-vlan-policy  {guest-voice |
guest-voice-signaling softphone-voice | streaming-video |
video-conferencing | video-signaling | voice | voice-signaling}
{tagged | untagged}  dscp <0-63> l2-priority <0-7>
lldp
LLDP configurations.
med
Media Endpoint Discovery
media-vlan-policy Use the media-vlan-policy to create a policy, which can be
assigned to an interface.
 Policy id for the policy which is created.
guest-voice
Create a guest voice policy.
guest-voice-signaling Create a guest voice signaling policy.
softphone-voice
Create a softphone voice policy.
streaming-video
Create a streaming video policy.
video-conferencing
Create a video conferencing policy.
video-signaling
Create a video signaling policy.
voice
Create a voice policy.
voice-signaling
Create a voice signaling policy.
tagged
The policy uses tagged frames.
untagged The policy uses un-tagged frames.
 The VLAN the policy uses tagged frames.
dscp
Differentiated Services Code Point.
<0-63> DSCP value 0-63
l2-priority Layer 2 priority.
<0-7> Priority 0-7
Default:
0
Usage Guide:
To configure media-VLAN-policy of LLDP-MED
Example:
To configure media-VLAN-policy as below table of LLDP-MED

Switch# configure terminal
Switch (config)# lldp med media-vlan-policy 1 guest-voice
tagged 1 dscp 45 l2-priority 5

lldp reinit
Command:
lldp reinit <1-10>
lldp
LLDP configurations.
reinit
LLDP tx reinitialization delay in seconds
<1-10> 1-10 seconds.

164

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Default:
2
Usage Guide:
To configure Tx re-initialization delay time of LLDP
Example:
To configure Tx re-initialization delay time (5) of LLDP
Switch# configure terminal
Switch (config)# lldp reinit 5

lldp timer
Command:
lldp timer <5-32768>
lldp
timer

LLDP configurations.
Sets LLDP TX interval (The time between each LLDP frame transmitted
in seconds)
<5-32768> 5-32768 seconds.

Default:
30
Usage Guide:
To configure Tx interval time of LLDP
Example:
To configure Tx interval time (555) of LLDP
Switch# configure terminal
Switch (config)# lldp timer 555

lldp transmission-delay
Command:
lldp transmission-delay <1-8192>
lldp
LLDP configurations.
transmission-delay Sets LLDP transmision-delay. LLDP transmission delay
(the amount of time that the transmission of LLDP frames
will delayed after LLDP configuration has changed) in
seconds.)
<1-8192> 1-8192 seconds.
Default:
2
Usage Guide:
To configure Tx transmission-delay time of LLDP
Example:
To configure Tx transmission-delay time (88) of LLDP

NS3500-24T-4C Managed Switch Command Guide

165

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# lldp transmission-delay 88

logging host
Command:
logging host  | 
logging
Syslog
host host

Domain name of the log server
 IP address of the log server
Default:
0
Usage Guide:
To configure address of log server
Example:
To configure address of log server
Switch# configure terminal
Switch (config)# logging host 192.168.5.5

logging level
Command:
logging level error | info | warning
logging
Syslog
level level
error
Error
info
Information
warning Warning
Default:
Info
Usage Guide:
To configure level of log server
Example:
To configure level of log server
Switch# configure terminal
Switch (config)# logging level error

logging on
Command:
logging on
logging
166

Syslog
NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

on

Enable syslog server

Default:
Disabled
Usage Guide:
To enable log server
Example:
To enable log server
Switch# configure terminal
Switch (config)# logging on

loop-protect
Command:
loop-protect
loop-protect

Loop protection configuration

Default:
Disabled
Usage Guide:
To enable Loop Protection
Example:
To enable Loop Protection
Switch# configure terminal
Switch (config)# loop-protect

loop-protect shutdown-time
Command:
loop-protect shutdown-time <0-604800>
loop-protect
Loop protection configuration
shutdown-time Loop protection shutdown time interval
<0-604800> Shutdown time in second
Default:
180
Usage Guide:
To configure shutdown time interval of Loop Protection
Example:
To configure shutdown time interval (888) of Loop Protection
Switch# configure terminal
Switch (config)# loop-protect shutdown-time 888

NS3500-24T-4C Managed Switch Command Guide

167

Chapter 4: Commands for CLI configuration

loop-protect transmit-time
Command:
loop-protect transmit-time <0-10>
loop-protect
Loop protection configuration
transmit-time Loop protection transmit time interval
<1-10> Transmit time in second
Default:
5
Usage Guide:
To configure Transmission Time of Loop Protection
Example:
To configure Transmission Time (8) of Loop Protection
Switch# configure terminal
Switch (config)# loop-protect transmit-time 8

mac address-table aging-time
Command:
mac address-table aging-time <0,10-1000000>
mac
MAC table entries/configuration
address-table MAC table entries/configuration
<0,10-1000000> Aging time in seconds, 0 disables aging
Default:
300
Usage Guide:
To configure Aging Time of MAC Address Table
Example:
To configure Aging Time (888) of MAC Address Table
Switch# configure terminal
Switch (config)# mac address-table aging-time 888

mac address-table static
Command:
mac address-table static  vlan 
interface * | 10GigabitEthernet  |
GigabitEthernet 
mac
MAC table entries/configuration
address-table MAC table entries/configuration
static
Static MAC address
 48 bit MAC address: xx:xx:xx:xx:xx:xx
vlan VLAN keyword
 VLAN IDs 1-4095

168

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

interface Select an interface to configure
*
All switches or All ports
GigabitEthernet
1 Gigabit Ethernet Port
10GigabitEthernet 10 Gigabit Ethernet Port
Default:
300
Usage Guide:
To configure Static MAC Address Table
Example:
To configure Static MAC Address Table as below table

Switch# configure terminal
Switch (config)# mac address-table static 00:11:22:33:44:55
vlan 1 interface GigabitEthernet 1/1

mep  ais
Command:
mep  ais [ fr1m | fr1s ] [ protect ]
mep
Maintenance Entity Point
 The MEP instance number.
ais
Alarm Indication Signal
fr1m
Frame rate is 1 f/min.
fr1s
Frame rate is 1 f/s.
protect The AIS can be used for protection. At the point of state change three
AIS PDU is transmitted as fast as possible.
Default:
None
Usage Guide:
To configure AIS of MEP
Example:
To configure AIS of MEP 1 as below table

Switch# configure terminal
Switch (config)# mep 1 ais fr1s

mep  aps
Command:
mep  aps  [ multi | uni ] { laps | { raps [ octet
 ] } }
mep
Maintenance Entity Point
NS3500-24T-4C Managed Switch Command Guide

169

Chapter 4: Commands for CLI configuration

 The MEP instance number.
aps
Automatic Protection Switching protocol
laps Linear Automatic Protection Switching protocol.
multi OAM PDU is transmitted with multicast MAC. Must me 'multi' in case of
RAPS.
uni
OAM PDU is transmitted with unicast MAC. The MAC is taken from peer
MEP MAC database. Only possible in case of LAPS.
raps Ring Automatic Protection Switching protocol.
octet Then last OCTET in the multicast MAC. Only possible in case of RAPS.
 Last OCTET value
uni
OAM PDU is transmitted with unicast MAC. The MAC is taken from peer
MEP MAC database. Only possible in case of LAPS.
Default:
None
Usage Guide:
To configure APS of MEP
Example:
To configure APS of MEP 1 as below table

Switch# configure terminal
Switch (config)# mep 1 aps 7 laps

mep  cc
Command:
mep  cc  fr100s | fr10s | fr1m | fr1s |
fr300s | fr6h | fr6m
mep
Maintenance Entity Point
 The MEP instance number.
cc
Continuity Check
 Priority in case of tagged OAM. In the EVC domain this is the COSID.
fr100s Frame rate is 100 f/s.
fr10s Frame rate is 10 f/s.
fr1m
Frame rate is 1 f/min.
fr1s
Frame rate is 1 f/s.
fr300s Frame rate is 300 f/s.
fr6h
Frame rate is 6 f/hour.
fr6m
Frame rate is 6 f/min.
Default:

Usage Guide:
To configure CC of MEP

170

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Example:
To configure CC of MEP 1 as below table

Switch# configure terminal
Switch (config)# mep 1 cc 2 fr10s

mep  client domain
Command:
mep  client domain { evc | vlan }
mep
Maintenance Entity Point
 The MEP instance number.
client Transport layer Client
evc EVC Domain.
vlan Vlan Domain
Default:
EVC
Usage Guide:
To configure Client Domain of MEP
Example:
To configure Client Domain (EVC) of MEP 1
Switch# configure terminal
Switch (config)# mep 1 client domain evc

mep  client flow
Command:
mep  client flow  level  [ ais-prio
[  | ais-highest ] ] [ lck-prio [  | lckhighest ] ]
mep
Maintenance Entity Point
 The MEP instance number.
level The MEG level on the client layer
 The MEG level value
ais-prio AIS injection priority
 AIS injection priority value
ais-highest
Request the highest possible AIS priority
lck-prio LCK injection priority
 LCK injection priority value.
lck-highest
Request the highest possible LCK priority.
Default:
0
Usage Guide:

NS3500-24T-4C Managed Switch Command Guide

171

Chapter 4: Commands for CLI configuration

To configure Client Flow of MEP
Example:
To configure Client Flow of MEP 1 as below table.

Switch# configure terminal
Switch (config)# mep 1 client flow 5 level 4 ais-prio ais-highest
lck-prio 3

mep  dm
Command:
mep  dm  [ multi | { uni mep-id  } ]
[ single | dual ] [ rdtrp | flow ] interval  last-n 
mep
Maintenance Entity Point
 The MEP instance number.
dm
Delay Measurement

Priority in case of tagged OAM. In the EVC domain this is the
COS-ID
dual
Delay Measurement based on 1DM PDU transmission.
flow
The two way delay is calculated as round trip symmetrical flow delay. The
far end residence time is subtracted.
interval Interval between PDU transmission in 10ms. Min value is 10.
 Interval value
multi
OAM PDU is transmitted with multicast MAC.
rdtrp
The two way delay is calculated as round trip delay. The far end residence
time is not subtracted.
single
Delay Measurement based on DMM/DMR PDU.
uni
OAM PDU is transmitted with unicast MAC. The MAC is taken from peer
MEP MAC database.
mep-id Peer MEP-ID for unicast DM. The MAC is taken from peer MEP MAC
database.
 Peer MEP-ID value
last-n The last N dalays used for average last N calculation. Min value is 10.
 The last N value
Default:
0
Usage Guide:
To configure Delay Measurement of MEP
Example:
To configure Delay Measurement of MEP 1 as below table.

172

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# mep 1 dm 5 rdtrp interval 10 last-n 10

mep  dm ns
Command:
mep  dm ns
mep
Maintenance Entity Point
 The MEP instance number.
dm
Delay Measurement
ns
Nano Seconds
Default:
us
Usage Guide:
To configure Delay Measurement of MEP
Example:
To configure Delay Measurement unit (ns) of MEP 1 as below table.

Switch# configure terminal
Switch (config)# mep 1 dm ns

mep  dm overflow-reset
Command:
mep  dm overflow-reset
mep
Maintenance Entity Point
 The MEP instance number.
dm
Delay Measurement
overflow-reset Reset all Delay Measurement results on total delay counter
overflow.
Default:
Keep
Usage Guide:
To reset Delay Measurement of MEP while overflowing
Example:
To reset Delay Measurement of MEP 1 while overflowing

NS3500-24T-4C Managed Switch Command Guide

173

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# mep 1 dm overflow-reset

mep  dm proprietary
Command:
mep  dm proprietary
mep Maintenance Entity Point
 The MEP instance number.
dm
Delay Measurement
proprietary
Proprietary Delay Measurement
Default:
Standard
Usage Guide:
To configure Tx mode (proprietary) of MEP.
Example:
To configure Tx mode (proprietary) of MEP 1
Switch# configure terminal
Switch (config)# mep 1 dm proprietary

mep  dm syncronized
Command:
mep  dm syncronized
mep
Maintenance Entity Point
 The MEP instance number.
dm
Delay Measurement
syncronized
Near enad and far end is real time syncronized.
Default:
Enabled
Usage Guide:
To configure Time Sync of MEP.
Example:
To configure Time Sync of MEP 1
Switch# configure terminal
Switch (config)# mep 1 dm syncronized

mep  down
Command:
mep  [ mip ] down domain { port | evc | vlan } [ vid
 ] flow  level  interface  
mep Maintenance Entity Point

174

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

mip
This MEP instance is a half-MIP
 The MEP instance number.
down This MEP is a Down-MEP
domain The domain of the MEP
evc This MEP is a EVC domain MEP.
port This MEP is a Port domain MEP.
vlan This MEP is a VLAN domain MEP.
flow The flow instance that the MEP is related to.
 The flow instance number when not in the port domain.
vid In case the MEP is a port Up-MEP or a EVC customer MIP the VID must be
given.
 The port Domain MEP VID. This is required for a Port Up-MEP.
Default:
None
Usage Guide:
To configure Down-MEP of MEP.
Example:
To configure Down-MEP of MEP 1 as below table

Switch# configure terminal
Switch (config)# mep 1 down domain port flow 1 level 0
interface GigabitEthernet 1/1

mep  lb
Command:
mep  lb  [ dei ] [ multi | { uni { { mep-id
 } | { mac  } } } ] count  size 
interval 
mep
Maintenance Entity Point
 The MEP instance number.
lb
Loop Back
 Priority in case of tagged OAM. In the EVC domain this is the COSID.
count The number of LBM PDU to send in one loop test. The value 0 indicate
infinite transmission (test behavior). This is HW based LBM/LBR and
Requires VOE.
 Number of LBM PDU to send value
size The number of bytes in the LBM PDU Data Pattern TLV
 The LBM frame size. This is entered as the wanted size (in bytes) of a
un-tagged frame containing LBM OAM PDU - including CRC (four
bytes). Example when 'Size' = 64 => Un-tagged frame size = DMAC(6)
+ SMAC(6) + TYPE(2) + LBM PDU LENGTH(46) + CRC(4) = 64
interval The number of bytes in the LBM PDU Data Pattern TLV
 The interval between transmitting LBM PDU. in case 'count' != 0 this

NS3500-24T-4C Managed Switch Command Guide

175

Chapter 4: Commands for CLI configuration

is in 10ms and max is 100. In case 'count' == 0 this is in 1us and
max is 10.000.
dei
Drop Eligible Indicator in case of tagged OAM.
multi OAM PDU is transmitted with multicast MAC.
uni
OAM PDU is transmitted with unicast MAC. The MAC is taken from
peer MEP MAC database.
mac
Loop Back unicast MAC to be used in case of LB against MIP.
 Loop Back target unicast MAC value
mep-id Peer MEP-ID for unicast LB. The MAC is taken from peer MEP MAC
database.
 Peer MEP-ID value
Default:
None
Usage Guide:
To configure Loop Back of MEP.
Example:
To configure Loop Back of MEP 2 as below table

Switch# configure terminal
Switch (config)# mep 2 lb 1 dei count 10 size 64 interval 100

mep  lck
Command:
mep  lck fr1m | fr1s
mep Maintenance Entity Point
 The MEP instance number.
lck Locked Signal
fr1m Frame rate is 1 f/min.
fr1s Frame rate is 1 f/s.
Default:
1 frame/sec
Usage Guide:
To configure Locked Frame Rate of MEP.
Example:
To configure Locked Frame Rate (1 frame/sec) of MEP 2.
Switch# configure terminal
Switch (config)# mep 2 lck
Switch (config)# mep 2 lck fr1s

176

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

mep  level
Command:
mep  level 
mep
Maintenance Entity Point
 The MEP instance number.
level
The MEG level of the MEP
 The MEG level value
Default:
0
Usage Guide:
To configure MEG level of MEP.
Example:
To configure MEG level (2) of MEP 2.
Switch# configure terminal
Switch (config)# mep 2 level 2

mep  lm
Command:
mep  lm  [ multi | uni ] [ single | dual ] [ fr10s
| fr1s | fr6m | fr1m | fr6h ] [ flr  ]
mep
Maintenance Entity Point
 The MEP instance number.
lm
Loss Measurement
 Priority in case of tagged OAM. In the EVC domain this is the COSID.
fr10s Frame rate is 10 f/s.
fr1m
Frame rate is 1 f/min.
fr1s
Frame rate is 1 f/s.
fr6h
Frame rate is 6 f/hour.
fr6m
Frame rate is 6 f/min.
dual
Dual ended LM is based on CCM PDU.
single Single ended LM is based on LMM/LMR PDU.
multi OAM PDU is transmitted with multicast MAC.
uni
OAM PDU is transmitted with unicast MAC. The MAC is taken from peer
MEP MAC database. In case of LM there is only one peer MEP.
flr
The Frame Loss Ratio interval.
 The Frame Loss Ratio interval value.
Default:

Usage Guide:
To configure Loss Measurement of MEP.
Example:
To configure Loss Measurement of MEP 2 as below table

NS3500-24T-4C Managed Switch Command Guide

177

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# mep 2 lm 5 uni flr 4

mep  lt
Command:
mep  lt  { { mep-id  } | { mac
 } } ttl 
mep
Maintenance Entity Point
 The MEP instance number.
lt
Link Trace
 Priority in case of tagged OAM. In the EVC domain this is the COSID.
mac Link Trace target unicast MAC to be used in case of LT against MIP.
 Link Trace target unicast MAC value.
mep-id Peer MEP-ID for Link Trace target unicast MAC. The MAC is taken from
peer MEP MAC database.
 Peer MEP-ID value.
ttl Time To Live.
 Time To Live value
Default:

Usage Guide:
To configure Link Trace of MEP.
Example:
To configure Link Trace of MEP 1 as below table

Switch# configure terminal
Switch (config)# mep 1 lt 4 mac 11-3A-15-A3-53-44

mep  meg-id
Command:
mep  meg-id  { itu | itu-cc | { ieee [ name
 ] } }
mep Maintenance Entity Point
 The MEP instance number.
meg-id The ITU/IEEE MEG-ID
 The MEG-ID string. This is either the ITU MEG-ID or the IEEE
Short MA, depending on the selected MEG-ID format. The
ITU max. is 13 characters. The ITU-CC max. is 15

178

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

characters. The IEEE max. is 16 characters..
The MEG-ID (Short MA Name) has IEEE Character String format. The meg-id
max. is 16 characters.
itu The MEG-ID has ITU format (ICC - UMC). The meg-id max. is 13 characters.
itu-cc The MEG-ID has ITU Country Code format (CC - ICC - UMC). The meg-id
max. is 15 characters
name Only relevant for IEEE. The MAID is with Maintenance Domain Name
 Maintenance Domain Name string. The max is 16 characters
ieee

Default:

Usage Guide:
To configure MEG-ID of MEP.
Example:
To configure MEG-ID of MEP 1 as below table

Switch# configure terminal
Switch (config)# mep 1 meg-id ICC000MEG0000 ieee name
interlogix.com

mep  mep-id
Command:
mep  mep-id 
mep Maintenance Entity Point
 The MEP instance number.
mep-id The MEP-ID
 The MEP-ID value.
Default:
None
Usage Guide:
To configure MEP-ID of MEP.
Example:
To configure MEP-ID (5) of MEP 1.
Switch# configure terminal
Switch (config)# mep 1 mep-id 5

NS3500-24T-4C Managed Switch Command Guide

179

Chapter 4: Commands for CLI configuration

mep  peer-mep-id
Command:
mep  peer-mep-id  [ mac  ]
mep Maintenance Entity Point
 The MEP instance number.
peer-mep-id The peer MEP-ID
 The peer MEP-ID value
mac The peer MAC. this will be overwritten by any learned MAC – through CCM
reception.
 The peer MAC string
Default:
None
Usage Guide:
To configure Peer MEP-ID of MEP.
Example:
To configure Peer MEP-ID of MEP 1 as below table

Switch# configure terminal
Switch (config)# mep 1 peer-mep-id 0 mac 11-3A-05-A1-53-11

mep  performance-monitoring
Command:
mep  performance-monitoring
mep
Maintenance Entity Point
 The MEP instance number.
performance-monitoring Performance monitoring Data Set collection (MEF35)
Default:
Disabled
Usage Guide:
To enable Performance Monitoring of MEP.
Example:
To enable Performance Monitoring of MEP 1
Switch# configure terminal
Switch (config)# mep 1 performance-monitoring

mep  tst
Command:
mep  tst  [ dei ] mep-id  [ sequence ]
[ all-zero | all-one | one-zero ] rate  size 
mep Maintenance Entity Point
180

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

 The MEP instance number.
tst
Test Signal
 Priority in case of tagged OAM. In the EVC domain this is the COSID.
dei
Drop Eligible Indicator in case of tagged OAM.
mep-id Peer MEP-ID for unicast TST. The MAC is taken from peer MEP MAC
database.
 Peer MEP-ID value
sequence Enable sequence number in TST PDU
all-one Test pattern is set to all one.
all-zero Test pattern is set to all zero.
one-zero Test pattern is set to 10101010.
rate
The TST frame transmission bit rate - in Mega bits pr. second. Limit on
Caracal is 400 Mbps. Limit on Serval is 1Gbps. This is the bit rate of
a standard frame without any encapsulation. If 1 Mbps rate is
selected in a EVC MEP, the added tag will give a
hi
 Transmission rate value
size The TST frame size. This is entered as the wanted size (in bytes) of a untagged frame containing TST OAM PDU - including CRC (four bytes).
Example when 'Size' = 64 => Un-tagged frame size = DMAC(6) +
SMAC(6) + TYPE(2) + TST PDU LENGTH(46) + CRC(4) = 64
 Frame size value
Default:

Usage Guide:
To enable Test Signal of MEP.
Example:
To enable Test Signal of MEP 1 as below table

Switch# configure terminal
Switch (config)# mep 1 tst 3 dei mep-id 2 sequence one-zero
rate 10 size 68

mep  up
Command:
mep  [mip] up domain { port | evc | vlan } [ vid
 ] flow  level  interface  
mep Maintenance Entity Point
 The MEP instance number.
mip
This MEP instance is a half-MIP
up
This MEP is a Up-MEP
domain The domain of the MEP
evc This MEP is a EVC domain MEP.
port This MEP is a Port domain MEP.
NS3500-24T-4C Managed Switch Command Guide

181

Chapter 4: Commands for CLI configuration

vlan This MEP is a VLAN domain MEP.
flow The flow instance that the MEP is related to.
 The flow instance number when not in the port domain.
vid In case the MEP is a port Up-MEP or a EVC customer MIP the VID must be
given.
 The port Domain MEP VID. This is required for a Port Up-MEP.
Default:
None
Usage Guide:
To configure Up-MEP of MEP.
Example:
To configure Up-MEP of MEP 2 as below table

Switch# configure terminal
Switch (config)# mep 2 up domain port vid 1 flow 1 level 2
interface GigabitEthernet 1/1

mep  vid
Command:
mep  vid 
mep
Maintenance Entity Point
 The MEP instance number.
vid
The MEP VID
 The MEP VID value
Default:
0
Usage Guide:
To set VID of MEP.
Example:
To set VID (8) of MEP 1.
Switch# configure terminal
Switch (config)# mep 1 vid 8

mep  voe
Command:
mep  voe
mep
Maintenance Entity Point
 The MEP instance number.
voe
MEP is VOE based

182

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Default:
0
Usage Guide:
To set VOE of MEP.
Example:
To set VOE (8) of MEP 1
Switch# configure terminal
Switch (config)# mep 1 voe

monitor destination
Command:
monitor destination interface 10GigabitEthernet
 | GigabitEthernet 
monitor
Set monitor configuration
destination The destination port. That is the port that trafficed should be
mirrored to
Default:
Disabled
Usage Guide:
To configure Mirroring Port
Example:
To set Mirroring Port (GigabitEthernet 1/2)
Switch# configure terminal
Switch (config)# monitor destination interface GigabitEthernet
1/2

monitor source
Command:
monitor source interface * | 10GigabitEthernet
 | GigabitEthernet  { both | rx
| tx }
monitor
Set monitor configuration
source
The source port(s). That is the ports to be mirrored to the destination
port.
Default:
Disabled
Usage Guide:
To configure Mirrored Port
Example:
To set Mirrored Port (GigabitEthernet 1/1, Tx + Rx)
Switch# configure terminal
Switch (config)# monitor source interface GigabitEthernet 1/1 both

NS3500-24T-4C Managed Switch Command Guide

183

Chapter 4: Commands for CLI configuration

mvr
Command:
mvr
mvr

Multicast VLAN Registration configuration

Default:
Disabled
Usage Guide:
To enable MVR
Example:
To enable MVR
Switch# configure terminal
Switch (config)# mvr

mvr name  channel
Command:
mvr name  channel 
mvr
Multicast VLAN Registration configuration
name MVR multicast name
 MVR multicast VLAN name
channel MVR channel configuration
 Profile name
Default:
None
Usage Guide:
To configure channel interface of MVR profile
Example:
To configure channel interface (1) of MVR profile (123)
Switch# configure terminal
Switch (config)# mvr name 123 channel 1

mvr name  frame priority
Command:
mvr name  frame priority 
mvr Multicast VLAN Registration configuration
name MVR multicast name
 MVR multicast VLAN name
frame MVR control frame in TX
priority Interface CoS priority
 CoS priority ranges from 0 to 7
Default:

184

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

0
Usage Guide:
To configure frame priority of MVR profile
Example:
To configure frame priority (5) of MVR profile (123)
Switch# configure terminal
Switch (config)# mvr name 123 frame priority 5

mvr name  frame tagged
Command:
mvr name  frame tagged
mvr Multicast VLAN Registration configuration
name MVR multicast name
 MVR multicast VLAN name
frame MVR control frame in TX
tagged Tagged IGMP/MLD frames will be sent
Default:
None
Usage Guide:
To configure frame tagged of MVR profile
Example:
To configure frame tagged (frame tagged) of MVR profile (123)
Switch# configure terminal
Switch (config)# mvr name 123 frame tagged

mvr name  igmp-address
Command:
mvr name  igmp-address 
mvr
Multicast VLAN Registration configuration
name MVR multicast name
 MVR multicast VLAN name
igmp-address MVR address configuration used in IGMP
 A valid IPv4 unicast address
Default:
0.0.0.0
Usage Guide:
To configure the MVR address of MVR profile
Example:
To configure the MVR address (192.168.0.55) of MVR profile (123)
Switch# configure terminal
Switch (config)# mvr name 123 igmp-address 192.168.0.55

NS3500-24T-4C Managed Switch Command Guide

185

Chapter 4: Commands for CLI configuration

mvr name  last-member-query-interval
Command:
mvr name  last-member-query-interval

mvr
Multicast VLAN Registration configuration
name MVR multicast name
 MVR multicast VLAN name
last-member-query-interval Last Member Query Interval in tenths of seconds
 0 - 31744 tenths of seconds
Default:
5
Usage Guide:
To configure the Last Member Query Interval of MVR profile
Example:
To configure the Last Member Query Interval (50 seconds) of MVR profile (123)
Switch# configure terminal
Switch (config)# mvr name 123 last-member-query-interval 500

mvr name  mode
Command:
mvr name  mode { compatible | dynamic }
mvr
Multicast VLAN Registration configuration
name MVR multicast name
 MVR multicast VLAN name
mode MVR mode of operation
compatible Compatible MVR operation mode
dynamic
Dynamic MVR operation mode
Default:
Dynamic
Usage Guide:
To configure the mode of MVR profile
Example:
To configure the mode (compatible) of MVR profile (123)
Switch# configure terminal
Switch (config)# mvr name 123 mode compatible

mvr vlan 
Command:
mvr vlan 
mvr Multicast VLAN Registration configuration
vlan MVR multicast vlan
 MVR multicast VLAN list

186

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Default:
None
Usage Guide:
To create a profile of MVR VLAN
Example:
To create a profile of MVR VLAN (5)
Switch# configure terminal
Switch (config)# mvr vlan 5

mvr vlan  channel
Command:
mvr vlan  channel 
mvr Multicast VLAN Registration configuration
vlan MVR multicast vlan
 MVR multicast VLAN list
channel MVR channel configuration
 Profile name
Default:
0
Usage Guide:
To configure the channel of MVR profile
Example:
To configure the channel (1) of MVR VLAN (5)
Switch# configure terminal
Switch (config)# mvr vlan 5 channel 1

mvr vlan  frame priority
Command:
mvr vlan  frame priority 
mvr Multicast VLAN Registration configuration
vlan MVR multicast vlan
 MVR multicast VLAN list
frame MVR control frame in TX
priority Interface CoS priority
 CoS priority ranges from 0 to 7
Default:
0
Usage Guide:
To configure the frame priority of MVR VLAN
Example:
To configure the frame priority (5) of MVR VLAN (123)

NS3500-24T-4C Managed Switch Command Guide

187

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# mvr vlan 123 frame priority 5

mvr vlan  tagged
Command:
mvr vlan  tagged
mvr Multicast VLAN Registration configuration
vlan MVR multicast vlan
 MVR multicast VLAN list
tagged Tagged IGMP/MLD frames will be sent
Default:
Enabled
Usage Guide:
To enable the IGMP/MLD frame tagged of MVR VLAN
Example:
To enable the IGMP/MLD frame tagged of MVR VLAN (123)
Switch# configure terminal
Switch (config)# mvr vlan 123 tagged

mvr vlan  igmp-address
Command:
mvr vlan  igmp-address 
mvr Multicast VLAN Registration configuration
vlan MVR multicast vlan
 MVR multicast VLAN list
igmp-address MVR address configuration used in IGMP
 A valid IPv4 unicast address
Default:
0.0.0.0
Usage Guide:
To configure the MVR address of MVR VLAN
Example:
To configure the MVR address (192.168.0.55) of of MVR VLAN (123)
Switch# configure terminal
Switch (config)# mvr vlan 123 igmp-address 192.168.0.55

188

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

mvr vlan  last-member-query-interval
Command:
mvr vlan  last-member-query-interval 
mvr Multicast VLAN Registration configuration
vlan MVR multicast vlan
 MVR multicast VLAN list
last-member-query-interval Last Member Query Interval in tenths of seconds
 0 - 31744 tenths of seconds
Default:
5
Usage Guide:
To configure the Last Member Query Interval of MVR VLAN
Example:
To configure the Last Member Query Interval (50 seconds) of MVR VLAN (123)
Switch# configure terminal
Switch (config)# mvr vlan 123 last-member-query-interval 500

mvr vlan  mode
Command:
mvr vlan  mode [ compatible | dynamic ]
mvr Multicast VLAN Registration configuration
vlan MVR multicast vlan
 MVR multicast VLAN list
mode MVR mode of operation
compatible Compatible MVR operation mode
dynamic
Dynamic MVR operation mode
Default:
Dynamic
Usage Guide:
To configure the mode of MVR VLAN
Example:
To configure the mode (compatible) of MVR VLAN (123)
Switch# configure terminal
Switch (config)# mvr vlan 123 mode compatible

mvr vlan  name
Command:
mvr vlan  name
mvr Multicast VLAN Registration configuration
vlan MVR multicast vlan

NS3500-24T-4C Managed Switch Command Guide

189

Chapter 4: Commands for CLI configuration

 MVR multicast VLAN list
name MVR multicast name
Default:
None
Usage Guide:
To configure profile name of MVR VLAN
Example:
To configure profile name (6) of MVR VLAN (5)
Switch# configure terminal
Switch (config)# mvr vlan 5 name 6

network-clock clk-source  aneg-mode
Command:
network-clock clk-source  aneg-mode { master |
slave | forced }
network-clock network-clock
clk-source
clk-source - commands related to a specific clock source.
 Clock source number
aneg-mode
Sets the preferred negotiation.
forced Activate forced slave negotiation
master Activate prefer master negotiation
slave Activate prefer slave negotiation
Default:
None
Usage Guide:
To configure preferred negotiation of network-clock
Example:
To configure preferred negotiation (slave) of network-clock (source 1)
Switch# configure terminal
Switch (config)# network-clock clk-source 1 aneg-mode slave

no
Command:
no
no

Negate a command or set its defaults

Default:
N/A
Usage Guide:
To default the function
Example:
To disable the function (loop-protect)

190

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# no loop-protect

ntp
Command:
ntp
ntp

Configure NTP

Default:
Disabled
Usage Guide:
To enable the NTP service
Example:
To enable the NTP service
Switch# configure terminal
Switch (config)# ntp

ntp server
Command:
ntp server <1-5> ip-address {  |  |
 }
ntp Configure NTP
server Configure NTP server
<1-5> index number

domain name
 ipv4 address
 ipv6 address
Default:
None
Usage Guide:
To configure the IP addresses of NTP Server
Example:
To configure the IP address (9.9.9.9) of NTP Server for index 1
Switch# configure terminal
Switch (config)# ntp server 1 ip-address 9.9.9.9

poe admin-mode enable
Command:
poe admin-mode enable
poe
Power Over Ethernet
admin-mode Enable or disable global PoE management function.

NS3500-24T-4C Managed Switch Command Guide

191

Chapter 4: Commands for CLI configuration

enable poe admin-mode enable
Default:
Enabled
Usage Guide:
To enable System PoE Admin Mode.
Example:
To enable System PoE Admin Mode.
Switch# configure terminal
Switch (config)# poe admin-mode enable

poe management mode
Command:
poe management mode { class-consumption | class-reservedpower | allocation-consumption | allocation-reserved-power |
lldp-consumption | lldp-reserved-power }
poe
Power Over Ethernet
management
Use management mode to configure PoE power management
method.
mode mode
allocation-consumption Max. port power determined by allocated, and power
is managed according to power consumption.
allocation-reserved-power Max. port power determined by alocated, and is
managed according to reserved power.
class-consumption
Max. port power determined by class, and power is
managed according to power consumption.
class-reserved-power
Max. port power determined by class, and power
managed according to reserved power.
lldp-consumption
Max. port power determined by LLDP Media protocol, and
power is managed according to consumption.
lldp-reserved-power Max. port power determined by LLDP Media protocol, and
power is managed according to reserved power.
Default:
Allocation-consumption
Usage Guide:
To configure PoE Management Mode.
Example:
To configure PoE Management Mode as LLDP-consumption mode.
Switch# configure terminal
Switch (config)# poe management mode lldp-consumption

poe sequential enable
Command:
poe sequential enable

192

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

poe
Power Over Ethernet
sequential PoE sequential is to delay power feeding when the switch is
completely booted.
enable
poe sequential enable
Default:
Enabled
Usage Guide:
To enable Sequential Power up Option.
Example:
To enable Sequential Power up Option.
Switch# configure terminal
Switch (config)# poe sequential enable

poe sequential interval
Command:
poe sequential interval <1-30>
poe
Power Over Ethernet
sequential
PoE sequential is to delay power feeding when the switch is
completely booted.
interval Set how long system should feeding power to next PoE interface <1-30>
<1-30> poe sequential enable
Default:
5
Usage Guide:
To configure Sequential Power up Interval.
Example:
To configure Sequential Power up Interval (30 seconds per port).
Switch# configure terminal
Switch (config)# poe sequential interval 30

poe sequential rule
Command:
poe sequential rule { port | priority }
poe
Power Over Ethernet
sequential rule PoE sequential is to delay power feeding when the switch is
completely booted.
port System sequential feeding power the PoE interfaces based port number.
priority Use priority command to configure sequential feeding power to PoE
interfaces based on port PoE priority.
Default:
Port

NS3500-24T-4C Managed Switch Command Guide

193

Chapter 4: Commands for CLI configuration

Usage Guide:
To configure Sequential Power up Port Option.
Example:
To configure Sequential Power up Port Option (Priority).
Switch# configure terminal
Switch (config)# poe sequential rule priority

poe supply
Command:
poe supply <1-XXX>
poe
Power Over Ethernet
supply Use poe supply to specify the maximum power the power supply can
deliver.
<1-XXX> Maximum power the power supply can deliver.
Default:
Maximum
Usage Guide:
To configure Power Supply Budget.
Example:
To configure Power Supply Budget (200 watts).
Switch# configure terminal
Switch (config)# poe supply 200

poe temperature-protection enable
Command:
poe temperature-protection enable
poe
Power Over Ethernet
temperature-protection Configure PoE over temperature protection to enable or
disable.
enable poe temperature-protection enable
Default:
Enabled
Usage Guide:
To enable PoE Temperature Protection.
Example:
To enable PoE Temperature Protection.
Switch# configure terminal
Switch (config)# poe temperature-protection enable

194

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

poe temperature-threshold
Command:
poe temperature-threshold <0-100>
poe Power Over Ethernet
temperature-threshold Set a lower high temperature threshold for the
secondary temperature alarm in degrees C.
<0-100> Specifies the new threshold temperature.
Default:
80
Usage Guide:
To enable PoE Temperature Protection.
Example:
To enable PoE Temperature Protection (70 degrees C).
Switch# configure terminal
Switch (config)# poe temperature-threshold 70

poe usage-threshold
Command:
poe usage-threshold <1-99>
poe
Power Over Ethernet
usage-threshold The poe usage-threshold command sets a percentage
threshold above which the system sends a log or SNMP
trap.<1-99>: The -threshold percentage configured with
this command.
<1-99> The usage-threshold percentage configured with this command.
Default:
85
Usage Guide:
To configure PoE Usage Threshold.
Example:
To configure PoE Usage Threshold (90 %).
Switch# configure terminal
Switch (config)# poe usage-threshold 90

poe-time-range
Command:
poe-time-range {profile1 | profile2 | profile3 | profile4}
poe-time-range Used to create PoE time-range for the switch and enter Power
Time-range Create Configuration Mode.
profile1 The PoE time-range profile name, ranging from Profile 1
profile2 The PoE time-range profile name, ranging from Profile 2

NS3500-24T-4C Managed Switch Command Guide

195

Chapter 4: Commands for CLI configuration

profile3
profile4

The PoE time-range profile name, ranging from Profile 3
The PoE time-range profile name, ranging from Profile 4

Default:
N/A
Usage Guide:
To enter PoE time-range profile mode.
Example:
To enter PoE time-range profile 1 mode
Switch# configure terminal
Switch (config)# poe-time-range profile1
Switch (config-poe-time-range)#
do
Command:
do < exec commands >
do

To run exec commands

Default:
N/A
Usage Guide:
To run exec commands
Example:
To run “show aaa”.
Switch# configure terminal
Switch (config)# poe-time-range profile1
Switch (config-poe-time-range)#do show aaa
console : local
telnet : local
ssh : local
http : local
end
Command:
end
end

Go back to EXEC mode

Default:
Auto
Usage Guide:
To back to EXEC mode

196

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Example:
To back to EXEC mode
Switch# configure terminal
Switch (config)# poe-time-range profile1
Switch (config-poe-time-range)#end
Switch#
exit
Command:
exit
exit

Exit from current mode

Default:
None
Usage Guide:
To exit current mode
Example:
To exit current mode.
Switch# configure terminal
Switch (config)# poe-time-range profile1
Switch (config-poe-time-range)#exit
Switch (config)#
no
Command:
no
no Negate a command or set its defaults
Default:
N/A
Usage Guide:
To default the function.
Example:
To enable the function (description 999).
Switch# configure terminal
Switch (config)# poe-time-range profile1
Switch (config-poe-time-range)#no description 999
periodic
Command:
periodic { Mon | Tue | Wed | Thu | Fri | Sat | Sun } 
 to   [ reboot 
 ]
periodic To create a periodic mode time-range for the PoE time-range of the
switch.
Fri Periodic Mode, with Friday.
NS3500-24T-4C Managed Switch Command Guide

197

Chapter 4: Commands for CLI configuration

Mon Periodic Mode, with Monday.
Sat Periodic Mode, with Saturday.
Sun Periodic Mode, with Sunday.
Thu Periodic Mode, with Thursday.
Tue Periodic Mode, with Tuesday.
Wed Periodic Mode, with Wednesday.
< start_h: 0-23> <0-23> start hour
< start_m: 0-59> <0-59> start minute
to start to end
< end_h: 0-23> <0-23> end hour
< end_m: 0-59> <0-59> end minute
reboot Enable reboot function
< reboot_h: 0-23> <0-23> reboot hour
< reboot_m:0-59> <0-59> reboot minute
Default:
N/A
Usage Guide:
To configure the Power Over Ethernet Schedule for specific profile.
Example:
To configure the Power Over Ethernet Schedule (below table) for specific profile
1.

Switch# configure terminal
Switch (config)# poe-time-range profile1
Switch (config-poe-time-range)# periodic Mon 11 59 to 22 50
reboot 11 44
reboot-only
Command:
reboot-only { Mon | Tue | Wed | Thu | Fri | Sat | Sun }
 
reboot-only
To create a periodic mode time-range for the PoE time-range of the
switch.
Fri Periodic Mode, with Friday.
Mon Periodic Mode, with Monday.
Sat Periodic Mode, with Saturday.
Sun Periodic Mode, with Sunday.
Thu Periodic Mode, with Thursday.
Tue Periodic Mode, with Tuesday.
Wed Periodic Mode, with Wednesday.
< reboot_h: 0-23> <0-23> reboot hour
< reboot_m:0-59> <0-59> reboot minute
Default:
N/A

198

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Usage Guide:
To configure the Power Over Ethernet Reboot Schedule for specific profile.
Example:
To configure the Power Over Ethernet Reboot Schedule (below table) for specific
profile.

Switch# configure terminal
Switch (config)# poe-time-range profile1
Switch (config-poe-time-range)# reboot Mon 0 0

port-security
Command:
port-security
port-security

Enable/disable port security globally

Default:
Disabled
Usage Guide:
To enable the Port Security
Example:
To enable the Port Security
Switch# configure terminal
Switch (config)# port-security

port-security aging
Command:
port-security aging
port-security Enable/disable port security globally
aging Enable/disable port security aging
Default:
Disabled
Usage Guide:
To enable the Port Aging
Example:
To enable the Port Aging
Switch# configure terminal
Switch (config)# port-security port-security aging

NS3500-24T-4C Managed Switch Command Guide

199

Chapter 4: Commands for CLI configuration

port-security aging time
Command:
port-security aging time <10-10000000>
port-security Enable/disable port security globally
aging Enable/disable port security aging
time Time in seconds between check for activity on learned MAC addresses
<10-10000000> seconds
Default:
3600
Usage Guide:
To configure the Aging Period of Port Security
Example:
To configure the Aging Period (159) of Port Security
Switch# configure terminal
Switch (config)# port-security aging time 159

privilege
Command:
privilege { exec | configure | config-vlan | line | interface | ifvlan | ipmc-profile | snmps-host | stp-aggr | dhcp-pool |
rfc2544-profile } level  
privilege
Command privilege parameters
config-vlan VLAN Configuration Mode
configure
Global configuration mode
dhcp-pool
DHCP Pool Configuration Mode
exec
Exec mode
if-vlan
VLAN Interface Mode
interface
Port List Interface Mode
ipmc-profile IPMC Profile Mode
line
Line configuration mode
rfc2544-profile RFC2544 Profile Mode
snmps-host SNMP Server Host Mode
stp-aggr
STP Aggregation Mode
level Set privilege level of command
<0-15> Privilege level
 Initial valid words and literals of the command to modify
Default:
None
Usage Guide:
To configure the Privilege Level for Command Line
Example:
To configure the Privilege Level (DHCP Pool mode, Level 12, Command: host) for
Command Line

200

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# privilege dhcp-pool level 12 host

qos map cos-dscp
Command:
qos map cos-dscp  dpl  dscp {  | { be
| af11 | af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 |
af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va } }
qos
Quality of Service
map Global QoS Map/Table
cos-dscp Map for cos to dscp
 Specific class of service or range
dscp Specify DSCP
 Specific DSCP
af11 Assured Forwarding PHB AF11(DSCP 10)
af12 Assured Forwarding PHB AF12(DSCP 12)
af13 Assured Forwarding PHB AF13(DSCP 14)
af21 Assured Forwarding PHB AF21(DSCP 18)
af22 Assured Forwarding PHB AF22(DSCP 20)
af23 Assured Forwarding PHB AF23(DSCP 22)
af31 Assured Forwarding PHB AF31(DSCP 26)
af32 Assured Forwarding PHB AF32(DSCP 28)
af33 Assured Forwarding PHB AF33(DSCP 30)
af41 Assured Forwarding PHB AF41(DSCP 34)
af42 Assured Forwarding PHB AF42(DSCP 36)
af43 Assured Forwarding PHB AF43(DSCP 38)
be
Default PHB(DSCP 0) for best effort traffic
cs1
Class Selector PHB CS1 precedence 1(DSCP 8)
cs2
Class Selector PHB CS2 precedence 2(DSCP 16)
cs3
Class Selector PHB CS3 precedence 3(DSCP 24)
cs4
Class Selector PHB CS4 precedence 4(DSCP 32)
cs5
Class Selector PHB CS5 precedence 5(DSCP 40)
cs6
Class Selector PHB CS6 precedence 6(DSCP 48)
cs7
Class Selector PHB CS7 precedence 7(DSCP 56)
ef
Expedited Forwarding PHB(DSCP 46)
va
Voice Admit PHB(DSCP 44)
Default:
0
Usage Guide:
To configure the DSCP Classification
Example:
To configure the DSCP Classification (QoS Class 3: DSCP CS1)
Switch# configure terminal
Switch (config)# qos map cos-dscp 3 dscp cs1

NS3500-24T-4C Managed Switch Command Guide

201

Chapter 4: Commands for CLI configuration

qos map dscp-classify
Command:
qos map dscp-classify {  | { be | af11 | af12 | af13
| af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 | af43 | cs1 |
cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va } }
qos
Quality of Service
map Global QoS Map/Table
dscp-classify Map for dscp classify enable
 Specific DSCP
af11 Assured Forwarding PHB AF11(DSCP 10)
af12 Assured Forwarding PHB AF12(DSCP 12)
af13 Assured Forwarding PHB AF13(DSCP 14)
af21 Assured Forwarding PHB AF21(DSCP 18)
af22 Assured Forwarding PHB AF22(DSCP 20)
af23 Assured Forwarding PHB AF23(DSCP 22)
af31 Assured Forwarding PHB AF31(DSCP 26)
af32 Assured Forwarding PHB AF32(DSCP 28)
af33 Assured Forwarding PHB AF33(DSCP 30)
af41 Assured Forwarding PHB AF41(DSCP 34)
af42 Assured Forwarding PHB AF42(DSCP 36)
af43 Assured Forwarding PHB AF43(DSCP 38)
be
Default PHB(DSCP 0) for best effort traffic
cs1 Class Selector PHB CS1 precedence 1(DSCP 8)
cs2 Class Selector PHB CS2 precedence 2(DSCP 16)
cs3 Class Selector PHB CS3 precedence 3(DSCP 24)
cs4 Class Selector PHB CS4 precedence 4(DSCP 32)
cs5 Class Selector PHB CS5 precedence 5(DSCP 40)
cs6 Class Selector PHB CS6 precedence 6(DSCP 48)
cs7 Class Selector PHB CS7 precedence 7(DSCP 56)
ef
Expedited Forwarding PHB(DSCP 46)
va
Voice Admit PHB(DSCP 44)
Default:
Disabled
Usage Guide:
To enabled the DSCP Ingress Classification
Example:
To configure the DSCP Ingress Classification (DSCP 36)
Switch# configure terminal
Switch (config)# qos map dscp-classify af42

qos map dscp-cos
Command:
qos map dscp-cos {  | { be | af11 | af12 | af13 |
af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 | af43 | cs1 |
cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va } } cos  dpl 
qos
Quality of Service

202

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

map Global QoS Map/Table
dscp-cos Map for dscp to cos
 Specific DSCP
af11
Assured Forwarding PHB AF11(DSCP 10)
af12
Assured Forwarding PHB AF12(DSCP 12)
af13
Assured Forwarding PHB AF13(DSCP 14)
af21
Assured Forwarding PHB AF21(DSCP 18)
af22
Assured Forwarding PHB AF22(DSCP 20)
af23
Assured Forwarding PHB AF23(DSCP 22)
af31
Assured Forwarding PHB AF31(DSCP 26)
af32
Assured Forwarding PHB AF32(DSCP 28)
af33
Assured Forwarding PHB AF33(DSCP 30)
af41
Assured Forwarding PHB AF41(DSCP 34)
af42
Assured Forwarding PHB AF42(DSCP 36)
af43
Assured Forwarding PHB AF43(DSCP 38)
be
Default PHB(DSCP 0) for best effort traffic
cs1
Class Selector PHB CS1 precedence 1(DSCP 8)
cs2
Class Selector PHB CS2 precedence 2(DSCP 16)
cs3
Class Selector PHB CS3 precedence 3(DSCP 24)
cs4
Class Selector PHB CS4 precedence 4(DSCP 32)
cs5
Class Selector PHB CS5 precedence 5(DSCP 40)
cs6
Class Selector PHB CS6 precedence 6(DSCP 48)
cs7
Class Selector PHB CS7 precedence 7(DSCP 56)
ef
Expedited Forwarding PHB(DSCP 46)
va
Voice Admit PHB(DSCP 44)
cos
Specify class of service
 Specific class of service
dpl
Specify drop precedence level
 Specific drop precedence level
Default:
0
Usage Guide:
To configure the DSCP-Based QoS Ingress Classification
Example:
To configure the DSCP-Based QoS Ingress Classification (DSCP: 44, QoS
Class: 6, DPL: 2)
Switch# configure terminal
Switch (config)# qos map dscp-cos va cos 6 dpl 2

qos map dscp-egress-translation
Command:
qos map dscp-egress-translation {  | { be | af11 |
af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 |
af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va } } to
{  | { be | af11 | af12 | af13 | af21 | af22 | af23 |
af31 | af32 | af33 | af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 |
cs6 | cs7 | ef | va } }

NS3500-24T-4C Managed Switch Command Guide

203

Chapter 4: Commands for CLI configuration

qos
Quality of Service
map Global QoS Map/Table
dscp-egress-translation Map for dscp egress translation
 Specific DSCP
af11 Assured Forwarding PHB AF11(DSCP 10)
af12 Assured Forwarding PHB AF12(DSCP 12)
af13 Assured Forwarding PHB AF13(DSCP 14)
af21 Assured Forwarding PHB AF21(DSCP 18)
af22 Assured Forwarding PHB AF22(DSCP 20)
af23 Assured Forwarding PHB AF23(DSCP 22)
af31 Assured Forwarding PHB AF31(DSCP 26)
af32 Assured Forwarding PHB AF32(DSCP 28)
af33 Assured Forwarding PHB AF33(DSCP 30)
af41 Assured Forwarding PHB AF41(DSCP 34)
af42 Assured Forwarding PHB AF42(DSCP 36)
af43 Assured Forwarding PHB AF43(DSCP 38)
be
Default PHB(DSCP 0) for best effort traffic
cs1
Class Selector PHB CS1 precedence 1(DSCP 8)
cs2
Class Selector PHB CS2 precedence 2(DSCP 16)
cs3
Class Selector PHB CS3 precedence 3(DSCP 24)
cs4
Class Selector PHB CS4 precedence 4(DSCP 32)
cs5
Class Selector PHB CS5 precedence 5(DSCP 40)
cs6
Class Selector PHB CS6 precedence 6(DSCP 48)
cs7
Class Selector PHB CS7 precedence 7(DSCP 56)
ef
Expedited Forwarding PHB(DSCP 46)
va
Voice Admit PHB(DSCP 44)
Default:
None
Usage Guide:
To configure the DSCP Egress Translation
Example:
To configure the DSCP Egress Translation (AF11 to AF12)
Switch# configure terminal
Switch (config)# qos map dscp-egress-translation af11 to af12

qos map dscp-ingress-translation
Command:
qos map dscp-ingress-translation {  | { be | af11 |
af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 |
af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va } } to
{  | { be | af11 | af12 | af13 | af21 | af22 | af23 |
af31 | af32 | af33 | af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 |
cs6 | cs7 | ef | va } }
qos
Quality of Service
map Global QoS Map/Table
dscp-ingress-translation Map for dscp ingress translation
 Specific DSCP

204

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

af11
af12
af13
af21
af22
af23
af31
af32
af33
af41
af42
af43
be
cs1
cs2
cs3
cs4
cs5
cs6
cs7
ef
va

Assured Forwarding PHB AF11(DSCP 10)
Assured Forwarding PHB AF12(DSCP 12)
Assured Forwarding PHB AF13(DSCP 14)
Assured Forwarding PHB AF21(DSCP 18)
Assured Forwarding PHB AF22(DSCP 20)
Assured Forwarding PHB AF23(DSCP 22)
Assured Forwarding PHB AF31(DSCP 26)
Assured Forwarding PHB AF32(DSCP 28)
Assured Forwarding PHB AF33(DSCP 30)
Assured Forwarding PHB AF41(DSCP 34)
Assured Forwarding PHB AF42(DSCP 36)
Assured Forwarding PHB AF43(DSCP 38)
Default PHB(DSCP 0) for best effort traffic
Class Selector PHB CS1 precedence 1(DSCP 8)
Class Selector PHB CS2 precedence 2(DSCP 16)
Class Selector PHB CS3 precedence 3(DSCP 24)
Class Selector PHB CS4 precedence 4(DSCP 32)
Class Selector PHB CS5 precedence 5(DSCP 40)
Class Selector PHB CS6 precedence 6(DSCP 48)
Class Selector PHB CS7 precedence 7(DSCP 56)
Expedited Forwarding PHB(DSCP 46)
Voice Admit PHB(DSCP 44)

Default:
None
Usage Guide:
To configure the DSCP Ingress Translation
Example:
To configure the DSCP Ingress Translation (AF11 to AF12)
Switch# configure terminal
Switch (config)# qos map dscp-ingress-translation af11 to af12

NS3500-24T-4C Managed Switch Command Guide

205

Chapter 4: Commands for CLI configuration

qos qce
Command:
qos qce  [ { next  } | last ] [ interface
(  [  ] ) ] [ smac {  |  |
any } ] [ dmac {  | unicast | multicast | broadcast |
any } ] [ tag { [ type { untagged | tagged | c-tagged | s-tagged |
any } ] [ vid {  | any } ] [ pcp {  | any } ] [ dei
{  | any } ] } ] [ inner-tag { [ type { untagged | tagged |
c-tagged | s-tagged | any } ] [ vid {  | any } ] [ pcp
{  | any } ] [ dei {  | any } ] } ] [ frame-type
{ any | { etype [ {  | any } ] } | { llc [ dsap
{  | any } ] [ ssap {  | any } ] [ control
{  | any } ] } | { snap [ {  | any } ] } |
{ ipv4 [ proto {  | tcp | udp | any } ] [ sip {  | any } ]
[ dip {  | any } ] [ dscp {  | { be | af11 | af12 |
af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 | af43 |
cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va } | any } ]
[ fragment { yes | no | any } ] [ sport {  | any } ] [ dport
{  | any } ] } | { ipv6 [ proto {  | tcp | udp | any } ]
[ sip {  | any } ] [ dip {  | any } ] [ dscp {  |
{ be | af11 | af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 |
af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef |
va } | any } ] [ sport {  | any } ] [ dport {  |
any } ] } } ] [ action { [ cos {  | default } ] [ dpl
{  | default } ] [ pcp-dei { 
 | default } ] [ dscp {  | { be |
af11 | af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 |
af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va } |
default } ] [ policy {  | default } ] } ]
qos Quality of Service
qce QoS Control Entry
action Setup action
dmac Setup matched DMAC
frame-type Setup matched frame type
interface Interfaces
last Place QCE at the end
next Place QCE before the next QCE ID
smac Setup matched SMAC
tag Setup tag options
Default:
None
Usage Guide:
To configure the QCE
Example:
To configure the QCE 1 (below table) for interface GigabitEthernet 1/1-2

206

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# qos qce 1 interface GigabitEthernet 1/1-2 tag
type tagged vid 5 pcp 3 dei 1 dmac unicast frame-type ipv4
proto udp dscp 19 frag no sport 55 action cos 0 dpl 1 dscp 4

NS3500-24T-4C Managed Switch Command Guide

207

Chapter 4: Commands for CLI configuration

qos qce update
Command:
qos qce update  [ { next  } | last ]
[ interface (  [  ] ) ] [ smac {  |
 | any } ] [ dmac {  | unicast | multicast |
broadcast | any } ] [ tag { [ type { untagged | tagged | c-tagged
| s-tagged | any } ] [ vid {  | any } ] [ pcp {  |
any } ] [ dei {  | any } ] } ] [ inner-tag { [ type
{ untagged | tagged | c-tagged | s-tagged | any } ] [ vid
{  | any } ] [ pcp {  | any } ] [ dei {  |
any } ] } ] [ frame-type { any | { etype [ {  |
any } ] } | { llc [ dsap {  | any } ] [ ssap {  |
any } ] [ control {  | any } ] } | { snap
[ {  | any } ] } | { ipv4 [ proto {  | tcp | udp |
any } ] [ sip {  | any } ] [ dip {  | any } ] [ dscp
{  | { be | af11 | af12 | af13 | af21 | af22 | af23 | af31 |
af32 | af33 | af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 |
cs7 | ef | va } | any } ] [ fragment { yes | no | any } ] [ sport
{  | any } ] [ dport {  | any } ] } | { ipv6 [ proto
{  | tcp | udp | any } ] [ sip {  | any } ] [ dip { 
| any } ] [ dscp {  | { be | af11 | af12 | af13 | af21 | af22 |
af23 | af31 | af32 | af33 | af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4
| cs5 | cs6 | cs7 | ef | va } | any } ] [ sport {  | any } ]
[ dport {  | any } ] } } ] [ action { [ cos {  |
default } ] [ dpl {  | default } ] [ pcp-dei
{   | default } ] [ dscp
{  | { be | af11 | af12 | af13 | af21 | af22 |
af23 | af31 | af32 | af33 | af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4
| cs5 | cs6 | cs7 | ef | va } | default } ] [ policy { 
| default } ] } ]
qos Quality of Service
qce QoS Control Entry
update Update an existing QCE
action Setup action
dmac Setup matched DMAC
frame-type Setup matched frame type
interface Interfaces
last
Place QCE at the end
next Place QCE before the next QCE ID
smac Setup matched SMAC
tag Setup tag options
Default:
None
Usage Guide:
To update the QCE
Example:
To update the QCE 1 (DMAC: Unicast, Action: Cos 0).

208

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# qos qce update 1 dmac unicast action cos 0

qos qce refresh
Command:
qos qce refresh
qos Quality of Service
qce QoS Control Entry
refresh
Refresh QCE tables in hardware
Default:
None
Usage Guide:
To refresh the QCE
Example:
To refresh the QCE.
Switch# configure terminal
Switch (config)# qos qce refresh

qos wred
Command:
qos wred queue  min-th  mdp-1 
mdp-2  mdp-3 
qos Quality of Service
wred Weighted Random Early Discard
queue Specify queue
 Specific queue or range
min-th Specify minimum threshold
 Specific minimum threshold in percent
mdp-1 Specify drop probability for drop precedence level 1
 Specific drop probability in percent
mdp-2 Specify drop probability for drop precedence level 2
 Specific drop probability in percent
mdp-3 Specify drop probability for drop precedence level 3
 Specific drop probability in percent
Default:

NS3500-24T-4C Managed Switch Command Guide

209

Chapter 4: Commands for CLI configuration

Usage Guide:
To configure the Weighted Random Early Detection
Example:
To configure the Weighted Random Early Detection (below table)

Switch# configure terminal
Switch (config)# qos wred queue 1 min-th 2 mdp-1 3 mdp-2 4
mdp-3 5

radius-server attribute 32
Command:
radius-server attribute 32 
radius-server Configure RADIUS
32 NAS-Identifier
Default:
None
Usage Guide:
To configure the NAS-Identifier
Example:
To configure the NAS-Identifier (IFS)
Switch# configure terminal
Switch (config)# radius-server attribute 32 IFS

radius-server attribute 4
Command:
radius-server attribute 4 
radius-server Configure RADIUS
4 NAS-IP-Address
Default:
None
Usage Guide:
To configure the NAS-IP-Address
Example:
To configure the NAS-IP-Address (7.7.7.7)

210

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# radius-server attribute 4 7.7.7.7

radius-server attribute 95
Command:
radius-server attribute 95 
radius-server Configure RADIUS
95 NAS-IPv6-Address
Default:
None
Usage Guide:
To configure the NAS-IPv6-Address
Example:
To configure the NAS-IPv6-Address (2001::7788)
Switch# configure terminal
Switch (config)# radius-server attribute 95 2001::7788

radius-server deadtime
Command:
radius-server deadtime 
radius-server Configure RADIUS
deadtime
Time to stop using a RADIUS server that doesn't respond
 Time in minutes
Default:
0
Usage Guide:
To configure the Deadtime of Radius-Server
Example:
To configure the Deadtime (15) of Radius-Server
Switch# configure terminal
Switch (config)# radius-server deadtime 15

radius-server host
Command:
radius-server host  [ auth-port  ]
[ acct-port  ] [ timeout  ] [ retransmit
 ] [ key  ]
radius-server Configure RADIUS
host Specify a RADIUS server

NS3500-24T-4C Managed Switch Command Guide

211

Chapter 4: Commands for CLI configuration

 Hostname or IP address
acct-port UDP port for RADIUS accounting server
 UDP port number
auth-port UDP port for RADIUS authentication server
 UDP port number
key
Server specific key (overrides default)
 The shared key
retransmit Specify the number of retries to active server (overrides default)
 Number of retries for a transaction
timeout Time to wait for this RADIUS server to reply (overrides default)
 Wait time in seconds
Default:
None
Usage Guide:
To configure the Host of Radius-Server
Example:
To configure the Host (below table) of Radius-Server

Switch# configure terminal
Switch (config)# radius-server host interlogix.com timeout 10
retransmit 6 key 123456789

radius-server key
Command:
radius-server key 
radius-server Configure RADIUS
key Set RADIUS encryption key
 The shared key
Default:
None
Usage Guide:
To configure the Key of Radius-Server
Example:
To configure the Key (123456789) of Radius-Server
Switch# configure terminal
Switch (config)# radius radius-server key 123456789

radius-server retransmit
Command:
radius-server retransmit 
radius-server
212

Configure RADIUS
NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

retransmit Specify the number of retries to active server
 Number of retries for a transaction
Default:
3
Usage Guide:
To configure the retransmitted time of Radius-Server
Example:
To configure the retransmitted time (5) of Radius-Server
Switch# configure terminal
Switch (config)# radius-server retransmit 5

radius-server timeout
Command:
radius-server timeout 
radius-server Configure RADIUS
timeout Time to wait for a RADIUS server to reply
 Wait time in seconds
Default:
5
Usage Guide:
To configure the timeout of Radius-Server
Example:
To configure the timeout (10) of Radius-Server
Switch# configure terminal
Switch (config)# radius-server timeout 10

rmon alarm
Command:
rmon alarm  { | {{ ifInOctets | ifInUcastPkts |
ifInNUcastPkts | ifInDiscards | ifInErrors | ifInUnknownProtos
| ifOutOctets | ifOutUcastPkts | ifOutNUcastPkts |
ifOutDiscards | ifOutErrors } }}  { absolute | delta } rising-threshold

[] falling-threshold

[  ] { [ rising | falling | both ] }
rmon Remote Monitoring
alarm Configure an RMON alarm

MIB object to monitor
ifInDiscards The number of inbound packets that are discarded even the packets
are normal
ifInErrors
The number of inbound packets that contained errors preventing
NS3500-24T-4C Managed Switch Command Guide

213

Chapter 4: Commands for CLI configuration

them from being deliverable to a higher-layer protocol
ifInNUcastPkts The number of broad-cast and multi-cast packets delivered to a
higher-layer protocol
ifInOctets
The total number of octets received on the interface, including framing
characters
ifInUcastPkts The number of uni-cast packets delivered to a higher-layer protocol
ifInUnknownProtos The number of the inbound packets that were discarded
because of the unknown or un-support protocol
ifOutDiscards
The number of outbound packets that are discarded event the
packets is normal
ifOutErrors
The The number of outbound packets that could not be transmitted
because of errors
ifOutNUcastPkts The number of broad-cast and multi-cast packets that request to
transmit
ifOutOctets The number of octets transmitted out of the interface, including
framing characters
 ifIndex
 Sample interval
absolute Test each sample directly
delta
Test delta between samples
rising-threshold Configure the rising threshold
 rising threshold value

Event to fire on rising threshold crossing
falling-threshold Configure the falling threshold
 falling threshold value
 Event to fire on falling threshold crossing
both Trigger alarm when the first value is larger than the rising threshold or less
than the falling threshold (default)
falling Trigger alarm when the first value is less than the falling threshold
rising Trigger alarm when the first value is larger than the rising threshold
Default:
None
Usage Guide:
To configure the Alarm of RMON
Example:
To configure the Alarm (below table) of RMON

Switch# configure terminal
Switch (config)# rmon alarm 1 .1.3.6.1.2.1.2.2.1.10.15 50
absolute rising-threshold 1000 1 falling-threshold 520 1
falling

rmon event
Command:
rmon event  [ log ] [ trap  ]
{ [ description  ] }

214

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

rmon Remote Monitoring
event Configure an RMON event
 Event entry ID
description Specify a description of the event
 Event description
log Generate RMON log when the event fires
trap Generate SNMP trap when the event fires
 SNMP community string
Default:
None
Usage Guide:
To configure the Event of RMON
Example:
To configure the Event (below table) of RMON

Switch# configure terminal
Switch (config)# rmon event 1 log trap IFS description error

sflow agent-ip
Command:
sflow agent-ip { ipv4  | ipv6  }
sflow Statistics flow
agent-ip The agent IP address used as agent-address in UDP datagrams. Defaults
to IPv4 loopback address.
Default:
None
Usage Guide:
To configure the agent IP address of sFlow
Example:
To configure the agent IP address (10.10.10.10) of sFlow
Switch# configure terminal
Switch (config)# sflow agent-ip ipv4 10.10.10.10

sflow collector-address
Command:
sflow collector-address 
sflow
Statistics flow
collector-address Collector address
 IPv4 address or IPv6 address or hostname identifying the collector
receiver

NS3500-24T-4C Managed Switch Command Guide

215

Chapter 4: Commands for CLI configuration

Default:
None
Usage Guide:
To configure the Collector address of sFlow
Example:
To configure the Collector address (10.10.10.10) of sFlow
Switch# configure terminal
Switch (config)# sflow collector-address 10.10.10.10

sflow collector-port
Command:
sflow collector-port 
sflow
Statistics flow
collector-port
Collector UDP port
 Port number
Default:
None
Usage Guide:
To configure the Collector port number of sFlow
Example:
To configure the Collector port number (555) of sFlow
Switch# configure terminal
Switch (config)# sflow collector-port 555

sflow max-datagram-size
Command:
sflow max-datagram-size 
sflow Statistics flow
max-datagram-size Maximum datagram size
 bytes
Default:
None
Usage Guide:
To configure the Collector Maximum datagram size of sFlow
Example:
To configure the Collector Maximum datagram size (555 bytes) of sFlow
Switch# configure terminal
Switch (config)# sflow max-datagram-size 555

216

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

sflow timeout
Command:
sflow timeout 
sflow
Statistics flow
timeout Receiver timeout measured in seconds. The switch decrements the
timeout once per second, and as long as it is non-zero, the receiver
receives samples. Once the timeout reaches 0, the receiver and all its
configuration is reset to defaults.
 Number of seconds
Default:
None
Usage Guide:
To configure the Collector timeout of sFlow
Example:
To configure the Collector timeout (555 seconds) of sFlow
Switch# configure terminal
Switch (config)# sflow timeout 555

sfp temperature-threshold
Command:
sfp temperature-threshold <0-100>
sfp temperature-threshold Set a lower high temperature threshold for the
secondary
temperature alarm in
degrees C.
<0-100> Specifies the new threshold temperature.
Default:
None
Usage Guide:
To configure the SFP temperature-threshold of sFlow
Example:
To configure the SFP temperature-threshold (55 degrees C) of sFlow
Switch# configure terminal
Switch (config)# sfp temperature-threshold 55

snmp-server
Command:
snmp-server
snmp-server Set SNMP server's configurations
Default:
Enabled

NS3500-24T-4C Managed Switch Command Guide

217

Chapter 4: Commands for CLI configuration

Usage Guide:
To enable the SNMP Service
Example:
To enable the SNMP Service
Switch# configure terminal
Switch (config)# snmp-server

snmp-server access
Command:
snmp-server access  model { v1 | v2c | v3 |
any } level { auth | noauth | priv } [ read  ] [ write
 ]
snmp-server Set SNMP server's configurations
access
access configuration
 group name
model security model
any any security model
v1 v1 security model
v2c v2c security model
v3 v3 security model
level security level
auth
authNoPriv Security Level
noauth noAuthNoPriv Security Level
priv authPriv Security Level
read specify a read view for the group
 read view name
write specify a write view for the group
 write view name
Default:
None
Usage Guide:
To configure the Access of SNMP
Example:
To configure the Access (below table) of SNMP

Switch# configure terminal
Switch (config)# snmp-server access default_rw_group model
v2c level priv read default_view write default_view

snmp-server community
Command:
snmp-server community { v2c  [ ro | rw ] | v3
 [   ] }
218

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

snmp-server Set SNMP server's configurations
community Set the SNMP community
v2c SNMPv2c
 Community word
ro
Read only
rw
Read write
v3 SNMPv3
 Community word
 IPv4 address
 IPv4 netmask
Default:
None
Usage Guide:
To configure the Read / Write / Source network Community of SNMP
Example:
To configure the Read / Write / Source network Community (below table) of
SNMP

Switch# configure terminal
Switch (config)# snmp-server community v3 public
192.168.0.15 255.255.255.0

snmp-server contact
Command:
snmp-server contact 
snmp-server Set SNMP server's configurations
contact
Set the SNMP server's contact string
 contact string

Default:
None
Usage Guide:
To configure the sysContact string of SNMP
Example:
To configure the sysContact string (Server123) of SNMP
Switch# configure terminal
Switch (config)# snmp-server contact Server123

snmp-server engine-id
Command:

NS3500-24T-4C Managed Switch Command Guide

219

Chapter 4: Commands for CLI configuration

snmp-server engine-id local 
snmp-server Set SNMP server's configurations
engine-id Set SNMP engine ID
local Set SNMP local engine ID
 local engine ID
Default:
None
Usage Guide:
To configure the Engine IDof SNMP
Example:
To configure the Engine ID (1234567890) of SNMP
Switch# configure terminal
Switch (config)# snmp-server engine-id local 1234567890

snmp-server host
Command:
snmp-server host 
snmp-server Set SNMP server's configurations
host Set SNMP host's configurations
 Name of the host configuration
Default:
None
Usage Guide:
To enter the SNMP host mode
Example:
To enter the SNMP host mode (IFS)
Switch# configure terminal
Switch (config)# snmp-server host IFS
Switch (config-snmps-host)#
do
Command:
do < exec commands >
do To run exec commands.
Default:
N/A
Usage Guide:
To run exec commands.
Example:
To run “show aaa”.

220

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# snmp-server host IFS
Switch (config-snmps-host)#do show aaa
console : local
telnet : local
ssh : local
http : local
end
Command:
end
end

Go back to EXEC mode

Default:
Auto
Usage Guide:
To back to EXEC mode
Example:
To back to EXEC mode
Switch# configure terminal
Switch (config)# snmp-server host IFS
Switch (config-snmps-host)#end
Switch#
exit
Command:
exit
exit

Exit from current mode

Default:
None
Usage Guide:
To exit current mode
Example:
To exit current mode.
Switch# configure terminal
Switch (config)# snmp-server host IFS
Switch (config-snmps-host)#exit
Switch (config)#
host
Command:
host [ |  | ]  { informs | traps }
host
host configuration

hostname of SNMP trap host
NS3500-24T-4C Managed Switch Command Guide

221

Chapter 4: Commands for CLI configuration

 IP address of SNMP trap host
 IP address of SNMP trap host
 UDP port of the trap messages
informs
Send Inform messages to this host
traps Send Trap messages to this host
Default:
None
Usage Guide:
To configure Trap Host of SNMP
Example:
To configure Trap Host (below table) of SNMP

Switch# configure terminal
Switch (config)# snmp-server host IFS
Switch (config-snmps-host)# host interlogix.com 66 informs
no
Command:
no
no Negate a command or set its defaults
Default:
N/A
Usage Guide:
To default the function
Example:
To disable the function (host interlogix.com 66 informs)
Switch# configure terminal
Switch (config)# snmp-server host IFS
Switch (config-snmps-host)# no ip address dhcp
informs
Command:
informs retries  timeout 
informs Send Inform messages to this host
retries retires inform messages
 retires times
timeout timeout parmater
 timeout interval
Default:
None
Usage Guide:
To configure Trap Inform time of SNMP
222

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Example:
To configure Trap Inform time (below table) of SNMP

Switch# configure terminal
Switch (config)# snmp-server host IFS
Switch (config-snmps-host)# informs retries 2 timeout 55
shutdown
Command:
shutdown
shutdown

Disable the trap configuration

Default:
Disabled
Usage Guide:
To disable Trap mode of SNMP
Example:
To disable Trap mode of SNMP
Switch# configure terminal
Switch (config)# snmp-server host IFS
Switch (config-snmps-host)# shutdown
traps
Command:
traps [ aaa authentication ] [ system [ coldstart ]
[ warmstart ] ] [ switch [ stp ] [ rmon ] ]
traps
trap event configuration
aaa
AAA event group
authentication Authentication fail event
switch Switch event group
system System event group
coldstart Cold start event
warmstart Warm start event
rmon
RMON event
stp
STP event
Default:
Disabled
Usage Guide:
To configure Trap event of SNMP
Example:
To configure Trap event (STP, RMON) of SNMP

NS3500-24T-4C Managed Switch Command Guide

223

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# snmp-server host IFS
Switch (config-snmps-host)# traps switch rmon stp
version
Command:
version { v1 [  ] | v2 [  ] | v3 [ probe |
engineID  ] [  ] }
version Set SNMP trap version
v1 SNMP trap version 1
 SNMP trap community
v2 SNMP trap version 2
 SNMP trap community
v3 SNMP trap version 3
 seucrity name
engineID Configure trap server's engine ID
probe
Probe trap server's engine ID
Default:
Disabled
Usage Guide:
To configure Version of SNMP
Example:
To configure Version (below table) of SNMP

Switch# configure terminal
Switch (config)# snmp-server host IFS
Switch (config-snmps-host)# version v2 IFS

spanning-tree aggregation
Command:
spanning-tree aggregation
spanning-tree Spanning Tree protocol
aggregation Aggregation mode
Default:
None
Usage Guide:
To enter aggregation mode of STP
Example:
To enter aggregation mode of STP
Switch# configure terminal
Switch (config)# spanning-tree aggregation
Switch (config-stp-aggr)#

224

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

do
Command:
do < exec commands >
do

To run exec commands.

Default:
N/A
Usage Guide:
To run exec commands.
Example:
To run “show aaa”.
Switch# configure terminal
Switch (config)# spanning-tree aggregation
Switch (config-stp-aggr)#do show aaa
console : local
telnet : local
ssh : local
http : local
end
Command:
end
end

Go back to EXEC mode

Default:
Auto
Usage Guide:
To back to EXEC mode
Example:
To back to EXEC mode
Switch# configure terminal
Switch (config)# spanning-tree aggregation
Switch (config-stp-aggr)#end
Switch#
exit
Command:
exit
exit Exit from current mode
Default:
None
Usage Guide:
To exit current mode
Example:
To exit current mode.
NS3500-24T-4C Managed Switch Command Guide

225

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# spanning-tree aggregation
Switch (config-stp-aggr)#exit
Switch (config)#
no
Command:
no
no

Negate a command or set its defaults

Default:
N/A
Usage Guide:
To default the function
Example:
To disable the function (spanning-tree auto-edge)
Switch# configure terminal
Switch (config)# snmp-server host IFS
Switch (config-snmps-host)# no spanning-tree auto-edge
spanning-tree auto-edge
Command:
spanning-tree auto-edge
spanning-tree Spanning Tree protocol
auto-edge
Auto detect edge status
Default:
Enabled
Usage Guide:
To enable the Auto Edge of CIST Aggregated Port
Example:
To enable the Auto Edge of CIST Aggregated Port
Switch# configure terminal
Switch (config)# snmp-server host IFS
Switch (config-snmps-host)# spanning-tree auto-edge
spanning-tree bpdu-guard
Command:
spanning-tree bpdu-guard
spanning-tree Spanning Tree protocol
bpdu-guard Enable/disable BPDU guard
Default:
Disabled

226

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Usage Guide:
To enable the BPDU Guard of CIST Aggregated Port
Example:
To enable the BPDU Guard of CIST Aggregated Port
Switch# configure terminal
Switch (config)# snmp-server host IFS
Switch (config-snmps-host)# spanning-tree bpdu-guard
spanning-tree edge
Command:
spanning-tree edge
spanning-tree Spanning Tree protocol
edge
Edge port

Default:
Disabled
Usage Guide:
To enable the Admin Edge of CIST Aggregated Port
Example:
To enable the Admin Edge of CIST Aggregated Port
Switch# configure terminal
Switch (config)# snmp-server host IFS
Switch (config-snmps-host)# spanning-tree edge
spanning-tree link-type
Command:
spanning-tree link-type link-type { point-to-point | shared |
auto }
spanning-tree Spanning Tree protocol
link-type Port link-type
auto
Auto detect
point-to-point Forced to point-to-point
shared
Forced to Shared
Default:
Point to Point
Usage Guide:
To configure the Point to Point mode (Shared) of CIST Aggregated Port
Example:
To configure the Point to Point mode (Shared) of CIST Aggregated Port
Switch# configure terminal
Switch (config)# snmp-server host IFS
Switch (config-snmps-host)# spanning-tree link-type shared

NS3500-24T-4C Managed Switch Command Guide

227

Chapter 4: Commands for CLI configuration

spanning-tree mst  cost
Command:
spanning-tree mst  cost {  | auto }
spanning-tree Spanning Tree protocol
mst STP bridge instance
 instance 0-7 (CIST=0, MST1=1...)
cost STP Cost of this port
 Cost range
auto Use auto cost
Default:
Auto
Usage Guide:
To configure the Path Cost of MSTI Port
Example:
To configure the Path Cost (321) of MSTI Port (MST 2)
Switch# configure terminal
Switch (config)# snmp-server host IFS
Switch (config-snmps-host)# spanning-tree mst 2 cost 321
spanning-tree mst  port-priority
Command:
spanning-tree mst  port-priority 
spanning-tree Spanning Tree protocol
mst
STP bridge instance
 instance 0-7 (CIST=0, MST1=1...)
port-priority STP priority of this port
 Range (lower higher priority)
Default:
Auto
Usage Guide:
To configure the Port Priority of MSTI Port
Example:
To configure the Port Priority (96) of MSTI Port (MST 2)
Switch# configure terminal
Switch (config)# snmp-server host IFS
Switch (config-snmps-host)# spanning-tree mst 2 port-priority
96
spanning-tree restricted-role
Command:
spanning-tree restricted-role
spanning-tree Spanning Tree protocol
restricted-role Port role is restricted (never root port)

228

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

Default:
Disabled
Usage Guide:
To enable the Restricted Role of CIST
Example:
To enable the Restricted Role of CIST
Switch# configure terminal
Switch (config)# snmp-server host IFS
Switch (config-snmps-host)# spanning-tree restricted-role
spanning-tree restricted-tcn
Command:
spanning-tree restricted-tcn
spanning-tree Spanning Tree protocol
restricted-tcn Restrict topology change notifications
Default:
Disabled
Usage Guide:
To enable the Restricted TCN of CIST
Example:
To enable the Restricted TCN of CIST
Switch# configure terminal
(config)# spanning-tree aggregation
(config-stp-aggr)# spanning-tree restricted-tcn

switchport vlan mapping
Command:
switchport vlan mapping  

switchport Set switching mode characteristics
vlan vlan - Vlan translation
mapping Add VLAN translation entry into a group
 Group id

VLAN list
< translation_vlan >
translation VLAN ID
Default:
None
Usage Guide:
To configure the VLAN Translation
Example:
To enable the VLAN Translation (below table)

NS3500-24T-4C Managed Switch Command Guide

229

Chapter 4: Commands for CLI configuration

Switch# configure terminal
Switch (config)# switchport vlan mapping 1 3 5

tacacs-server deadtime
Command:
tacacs-server deadtime 
tacacs-server Configure TACACS+
deadtime Time to stop using a TACACS+ server that doesn't respond
 Time in minutes
Default:
0
Usage Guide:
To configure the Deadtime of TACACS+ Server
Example:
To enable the Deadtime (6) of TACACS+ Server
Switch# configure terminal
Switch (config)# tacacs-server deadtime 6

tacacs-server host
Command:
tacacs-server host  [ port  ] [ timeout
 ] [ key  ]
tacacs-server Configure TACACS+
host Specify a TACACS+ server
 Hostname or IP address
key
Server specific key (overrides default)
port TCP port for TACACS+ server
 TCP port number
timeout Time to wait for this TACACS+ server to reply (overrides default)
 Wait time in seconds
 The shared key
Default:
None
Usage Guide:
To configure the Host of TACACS+ Server
Example:
To enable the Host (below table) of TACACS+ Server
Switch# configure terminal
Switch (config)# tacacs-server host interlogix.com port 55
timeout 6 key 7788

230

NS3500-24T-4C Managed Switch Command Guide

Chapter 4: Commands for CLI configuration

transport email authentication
Command:
transport email authentication username 
password 
transport Enable or disable transport email function.
email Enable or disable transport email function.
authentication configure SMTP authentication's username and password
 User name allows letters, numbers and underscores
 The ENCRYPTED (hidden) user password. Notice the
ENCRYPTED password will be decoded by system internally.
You cannot directly use it as same as the Plain Text and it is not
human-readable text normally.
Default:
N/A
Usage Guide:
To configure SMTP authentication's username and password
Example:
To configure SMTP authentication's username (123@interlogix.com) and password
(456)
Switch# configure terminal
Switch (config)# transport email authentication username
123@interlogix.com password 456

transport email from
Command:
transport email from  subject