Intermatic CA3000 Single Pole & Multi-Way Relay Type Wall Switch User Manual CA3000

Intermatic Inc Single Pole & Multi-Way Relay Type Wall Switch CA3000

Exhibit D Users Manual per 2 1033 b3

Providing a Brighter Solution™WARNING: Read instructions completely before installation and retain for future reference.WARNING:WARNING:OTHER CAUTIONS:For installation and/or use in accordance with appropriate electrical codes and regulations.Consult a qualified electrician for installation and operation.1. Use only one (1) switch per load. For remote operation, use standard 3-way or 4-way electrical devices forON/OFF operation or use with Z-Wave compatible control for wireless control from any location.2. Disconnect power when servicing or changing load.3. Use this device only with copper or copper clad wire.Model CA3000Single Pole & Multi-WayRelay Type Wall SwitchSpecifications:Ratings:Colors:Connections:RF Information:Network Information:Single-Pole (One Location)or 3-Way (Multi-Location)or Wireless RF Control120VAC, 50/60Hz1800 Watts 15A Tungsten;1800 Watts 15A Resistive/Inductive;1800VA 15A Ballast;1/2HP MotorIncludes white, ivory, and light almondsnap-on rocker plates.Black-Line, Blue-Load, Red-Traveler,White-Neutral, Green-GroundMinimum Range:50ft indoor; 100ft outdoorFrequency: 908.42 MHzMesh Network - Each line powerednode acts as a repeater to routedistant signals.Data Rate: 9600 bits/secondSize: 232 Z-Wave™ NodesOperating Temperature Range:32°F (0°C) to 104°F (40°C)Power Consumption: 2.0W MaxINSTALLATION:1. WARNING: TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF POWER AT CIRCUIT BREAKER ANDTEST THAT POWER IS OFF BEFORE WIRING.Operation:2. For retrofit applications, remove wall plate and disconnect switch.3. Refer to wiring diagrams for proper connection of switch for intended application.4. Check that all wire connections are secure.5. Place all wires inside junction box. Install switch using (2) mounting screws furnished. Completeinstallation with a decorator style wall-plate.6. Reconnect your electrical power.7. Tap top of rocker to turn load on; tap bottom of rocker to turn load off.8. For programming instructions refer to the (158CA12789).InTouch Installer & Users GuideThe CA3000 Wall Switch is a Z-wave™ enabled device which is fully compatible with any Z-wave enablednetwork. Z-wave enabled devices display the Z-wave logo and guarantee connectivity and interoperabilitybetween devices. Each line powered node in a Z-wave network is designed to act as a repeater forming amesh network eliminating radio “dead spots” and providing the highest level of reliability.- Mini-scenes allows local control of connected load plus up to 5 additional Z-wave enabled devices.- Switch always operates local load, and does not require central control system.Features- Multiple location On/Off when used with wireless accessory controls.- Multiple location On/Off control using conventional 3-way or 4-way wiring and devices.- Full 230 device scene control when used with Intermatic InTouch™ server (CA5500B).Rocker Color ConversionThe frame and rocker color of this device can beconverted to match interior design requirements.Simply use one of the included color plates (white,ivory, or light almond) and proceed as follows (pleasenote that the device must be removed from the junctionbox to change the rocker, follow the installationinstructions and warnings).1. Select the color of the face you desire.2. The frame has snaps on its sides. Using a smallscrewdriver or thumbnail, gently remove the frame androcker from the housing body.3. Take the new frame and position it properly to thehousing body. Notice that the locking snaps will align inonly the proper direction. Line up the plastic snaps withthe slots in the housing body and snap into place.4. The frame snaps in with an audible click. Ensure thatboth snaps are secure. Replace the device in thejunction box following installation instructions.The color conversion is complete.RockerFrame SnapThis product is compatible with other Z-Wave enabled products™FCC STATEMENT OF COMPLIANCEWARNING! Changes or modifications not expressly approved by Intermatic Inc. could void the user’s authority to operate theequipment.This device complies with part 15 of the FCC rules. Operation of this device is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference, including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference toradio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try tocorrect the interference by one or more of the following measures:-- Reorient or relocate the receiving antenna or device.-- Increase the separation between the equipment and receiver.-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-- Consult the dealer or an experienced radio/TV technician for help.158CA12470REFWIRELESS CONTROLSTM
WhiteSingle Pole ApplicationHot BlackNeutralBlueLoadRedWire Connector GroundGreen120VAC50/60 Hz3-Way ApplicationHot BlackNeutralBlueRedWire Connector GroundGreen120VAC50/60 HzJumperCA3000 CA3000 CA-3PS / Standard 3-Way SwitchMulti-Way ApplicationHot BlackNeutralBlueLoadRedWire Connector GroundGreen120VAC50/60 HzCA3000 CA-3PS / Standard 3-Way SwitchCA-4PS / Standard 4-Way SwitchCA-3PS / Standard 3-Way Switch CA-4PS / Standard 4-Way SwitchLIMITED TEN YEAR WARRANTYIf within ten (10) years from date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace, at itssole option. This warranty applies only to the original purchaser and is not transferable. This warranty excludes and this is disclaimed liability for labor forremoval of this product or reinstallation. The warranty does not apply to: (a) damage caused by accident, abuse, mishandling, dropping, acts of God, or anynegligent use; (b) units which have been subject to unauthorized repair, opened, taken apart, or otherwise modified; (c) units not used in accordance withdirections; (d) damages exceeding the cost of the product. Some states do not allow a limitation of damages, so the foregoing limitation may not apply to you.This warranty gives you specific legal rights and you may have other rights that vary from state to state.This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing postage prepaid to thenearest authorized service center listed. Please be sure to wrap the product securely when mailing to avoid shipping damage. This warranty is made by:Intermatic Incorporated, After Sales Service, 7777 Winn Road, Spring Grove, IL 60081-9698, 815-675-7000 www.intermatic.comINTERMATIC INCORPORATED WILL NOT BELIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES.ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULARPURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION ASTHE WARRANTY PERIOD STATED ABOVE.White LoadWhiteThis product is compatible with other Z-Wave enabled products™Wire Connector InstallationConnect wires per Single Pole, 3-Way, or Multi-WayApplication Diagrams as follows:Screw wire connectors on clockwise making sure nobare conductors show below the wire connector.Secure each connector with electrical tape.Insert wires straightthen twist clockwiseSecure each connnectorwith electrical tapeFor non-standard wiring applications, refer toWire Combination & Connector ChartYellow Wire Connector Combination Chart1- #10 AWG1 #12 AWGor2 #14 AWGor2 #16 AWG+1- #12 AWG1to2#12AWGor1to3#14AWGor1to4#16AWG+1- #14 AWG1to3#14AWGor1to4#16AWGor1to4#18AWG+1- #16 AWG1to4#16AWGor1to4#18AWG+Strip wires to expose3/8” of conductors3/8”Providing a Brighter Solution™WIRELESS CONTROLSTM

Navigation menu