Intermatic CA7100 Master In-Wall Control Station User Manual CA7100

Download:
Mirror Download [FCC.gov]
Document ID	714365
Application ID	MrsFkCIoGQou6ULwC3qrZA==
Document Description	Exhibit D Users Manual per 2 1033 b3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	87.2kB (1089956 bits)
Date Submitted	2006-10-11 00:00:00
Date Available	2006-10-11 00:00:00
Creation Date	2006-07-31 22:47:58
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2006-07-31 22:47:58
Document Title	CA7100.cdr
Document Creator	PScript5.dll Version 5.2

TM
Providing a Brighter Solution™
WIRELESS CONTROLS
Model CA7100
Master In-Wall Control Station
The CA7100 Master In-Wall Control Station is an enhanced radio
frequency controller compatible with Z-wave™ enabled networks and
devices. Each line powered node in a Z-wave network is designed to
act as a repeater forming a mesh network eliminating radio “dead
spots” and providing the highest level of reliability.
Features
- Menu driven setup of scenes and events.
- Built-in astronomic timing with real-time-clock backup.
- Multiple location On/Off & Raise/Lower control when used with Zwave enabled switches and dimmers.
- Allows control of up to 100 individual pre-set scenes containing any
number of Z-wave enabled devices.
- Features 6 “Quick” pre-set scene activator buttons.
- Features individual scene status feedback for enhanced control.
- Separate focus and control buttons allows the user to custom mix
scene selections and vary light levels.
- Home key provides for quick de-selection of scenes and back-out
from menu programming.
WARNING: Read instructions completely before installation and retain
for future reference.
WARNING: For installation and/or use in accordance with appropriate
electrical codes and regulations.
WARNING: Consult a qualified electrician for installation and operation.
OTHER CAUTIONS:
1. For remote operation of Z-Wave compatible controls.
2. Use this device only with copper or copper clad wire.
Note: Designed to work only in the presence of InTouch™
Server (CA5500B or other).
Specifications:
Wireless RF Control
Operating Temperature Range:
32°F (0°C) to 104°F (40°C)
Power Consumption: 4.0W Max
Backlit 128 x 64 Dot LCD Display
Ratings:
120VAC, 50/60Hz
Colors:
Includes white snap-on face plate.
Connections:
Black-Line, White-Neutral,
Green-Ground
RF Information:
Minimum Range:
50ft indoor; 100ft outdoor
Frequency: 908.42 MHz
Network Information:
Mesh Network - Each line powered
node acts as a repeater to route
distant signals.
Data Rate: 9600 bits/second
Size: 232 Z-Wave™ Nodes
INSTALLATION:
1. WARNING: TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF POWER AT CIRCUIT BREAKER AND
TEST THAT POWER IS OFF BEFORE WIRING.
2. Requires a 3-gang electrical junction box for installation.
3. Remove the face plate. Using a finger or thumb nail, remove the face plate from the housing body by lifting
on the right edge by the menu navigation buttons. Remove exposed (3) screws to release mounting plate.
4. Attach mounting plate to 3-gang electrical junction box using (6) mounting screws furnished.
5. Refer to wiring diagrams for proper connection of master in-wall control station.
6. Check that all wire connections are secure and place all wires inside junction box.
7. Replace master in-wall control station using (3) mounting screws. Complete installation by snapping cover
plate back into place.
8. Reconnect your electrical power.
9. Operation: Press the “Enter” button to access setup menus. Press scene number button(s) to focus
control activities; Press “Enter” to toggle selected scene(s); Press v / w to lower or raise selected scene(s)
lighting level; Press the home key to clear selected scene(s).
10. For programming instructions refer to the InTouch Installer & Users Guide (158CA12789).
Face Color Conversion
The face color of this device can be converted to match interior design requirements.
1. Select and obtain the color of the face you desire.
2. The face plate has snaps on 3 sides. Using a finger or thumb nail, remove the face plate from the housing
body by lifting on the right edge by the menu navigation buttons.
3. Take the new face plate and position it properly to the housing body. Notice that the left edge has tabs that
must be inserted first. Press the plate into position.
4. The face plate snaps in with an audible click. Ensure that all snaps are secure.
The color conversion is complete.
FCC STATEMENT OF COMPLIANCE
This device complies with part 15 of the FCC rules. Operation of this device is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna or device.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
WARNING! Changes or modifications not expressly approved by Intermatic Inc. could void the user’s authority to operate the
equipment.
158CA12474REF
TM
Providing a Brighter Solution™
WIRELESS CONTROLS
For non-standard wiring applications, refer to
Wire Combination & Connector Chart
Wire Connector Installation
Connect wires as follows:
Screw wire connectors on clockwise making sure no
bare conductors show below the wire connector.
Secure each connector with electrical tape.
Orange Wire Connector Combination Chart
1- #16 AWG
2- #16 AWG
1- #18 AWG
1 #14 AWG
or
1 #16 AWG
or
1-2 #18 AWG
3/8”
Strip wires to expose
3/8” of conductors
1- #14 AWG
Secure each connnector
with electrical tape
Insert wires straight
then twist clockwise
Standard Installation
Hot
120VAC
50/60 Hz
Black
Green
White
CA7100 Master
In-Wall Control Panel
Menu
Navigation
Controls
ENTER
ENTER
Neutral
Wire Connector
1 #16 AWG 1 to 2 #18 AWG 1 to 3 #18 AWG
or
1-2 #18 AWG
CA7100
Backlit 128 x 64
Dot LCD Display
Ground
Speaker
Scene Buttons
Home Button
LIMITED TEN YEAR WARRANTY
If within ten (10) years from date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace, at its
sole option. This warranty applies only to the original purchaser and is not transferable. This warranty excludes and this is disclaimed liability for labor for
removal of this product or reinstallation. The warranty does not apply to: (a) damage caused by accident, abuse, mishandling, dropping, acts of God, or any
negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart, or otherwise modified; (c) units not used in accordance with
directions; (d) damages exceeding the cost of the product. Some states do not allow a limitation of damages, so the foregoing limitation may not apply to you.
This warranty gives you specific legal rights and you may have other rights that vary from state to state. INTERMATIC INCORPORATED WILL NOT BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES.
ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS
THE WARRANTY PERIOD STATED ABOVE.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing postage prepaid to the
nearest authorized service center listed. Please be sure to wrap the product securely when mailing to avoid shipping damage. This warranty is made by:
Intermatic Incorporated, After Sales Service, 7777 Winn Road, Spring Grove, IL 60081-9698, 815-675-7000 www.intermatic.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:1765d1eb-dfa6-495b-b3ac-ea8f856ab527
Producer                        : Acrobat Distiller 6.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2006:07:31 22:47:58-05:00
Create Date                     : 2006:07:31 22:47:58-05:00
Document ID                     : uuid:6c5732a8-83cc-4c7e-9b9b-1dd9e08a5a8a
Format                          : application/pdf
Title                           : CA7100.cdr
Creator                         : 
Author                          : 

EXIF Metadata provided by EXIF.tools