Intermatic PE000953 Hand Held Transceiver User Manual Exhibit D Users Manual per 2 1033 b3

Intermatic Inc Hand Held Transceiver Exhibit D Users Manual per 2 1033 b3

Exhibit D Users Manual per 2 1033 b3

2 Multi-Wave PE653-PE953 Installation GuideCopyright © 2010 Intermatic, Inc.Important Safety InstructionsAll electrical work must be performed by a licensed electrician and conform to all national, state, and local codes. When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:DANGER: To reduce the risk of injury, do not remove the suction fittings of your spa or hot tub. Never operate a spa or hot tub if the suction fittings are broken or missing. Never replace a suction fitting with one rated less than the flow rate marked on the equipment assembly.WARNING: Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98.6°F. The symptoms of hyperthermia include dizziness, fainting, drowsiness, lethargy, and an increase in the internal temperature of the body. The effects of hyperthermia include: 1) unawareness of impending danger; 2) failure to perceive heat; 3) failure to recognize the need to exit spa; 4) physical inability to exit spa; 5) fetal damage in pregnant women; 6) unconsciousness resulting in a danger of drowning.WARNING: To Reduce the Risk of Injury —The water in a spa should never exceed 104°F (40°C). Water temperatures between 100°F •(38°C) and 104°F (40°C) are considered safe for a healthy adult. Lower water temperatures are recommended for young children and when spa use exceeds 10 minutes.Since excessive water temperatures have a high potential for causing fetal damage during •the early months of pregnancy, pregnant or possibly pregnant women should limit spa water temperatures to 100°F (38°C).Before entering a spa or hot tub, the user should measure the water temperature with an •accurate thermometer since the tolerance of water temperature-regulating devices varies.The use of alcohol, drugs, or medication before or during spa or hot tub use may lead to •unconsciousness with the possibility of drowning.Obese people and people with history of heart disease, low or high blood pressure, •circulatory system problems, or diabetes should consult a physician before using a spa. People using medication should consult a physician before using a spa or hot tub since some •medication may induce drowsiness while other medication may affect heart rate, blood pressure, and circulation.WARNING: Risk of electric shock – Install the control center at least five (5) feet (152.4cm) from the inside wall of the pool and/or hot tub using non-metallic plumbing. Canadian installations must be at least three (3) meters from the water.
Safety 3Providing a brighter solution.™• Children should not use spas or hot tubs without adult supervision.Do not use spas or hot tubs unless all suction guards are installed to prevent body and hair •entrapment.People using medications and/or having an adverse medical history should consult a •physician before using a spa or hot tub.People with infectious diseases should not use a spa or hot tub.•To avoid injury, exercise care when entering or exiting the spa or hot tub.•Do not use drugs or alcohol before or during the use of a spa or hot tub to avoid •unconsciousness and possible drowningPregnant or possibly pregnant women should consult a physician before using a spa or hot •tub.Water temperature in excess of 100°F (38°C) may be injurious to your health.•Before entering a spa or hot tub measure the water temperature with an accurate •thermometer.Do nut use a spa or hot tub immediately following strenuous exercise.•Prolonged immersion in a spa or hot tub may be injurious to your health.•Do not permit any electric appliance (such as a light, telephone, radio, or television) within 5 •feet (1.5m) of a spa or hot tub.The use of alcohol, drugs or medication can greatly increase the risk of fatal hyperthermia in •hot tubs and spas. Water temperature in excess of 100°F (38°C) may be hazardous to your health.•WARNING: To reduce the risk of electrical shock, connect the grounding terminal in the metal enclosure to the grounding terminal of your electric service or supply panel with a continuous copper conductor having green insulation and one that is equivalent in size to the circuit conductors supplying this equipment. In addition, a second wire connector should be bonded with a no. 8 AWG (4.115mm) copper wire to any metal ladders, water pipes, or other metal within five (5) feet (1.52m) of the tub.WARNING: A ground-fault circuit-interrupter must be provided if this device is used to control underwater lighting fixtures. The conductors on the load side of the ground-fault circuit-interrupter shall not occupy conduit, boxes or enclosures containing other conductors unless the additional conductors are also protected by a ground-fault circuit-interrupter. Refer to local codes for complete details.
4 Multi-Wave PE653-PE953 Installation GuideCopyright © 2010 Intermatic, Inc.ContentsImportant Safety Instructions ...........................................................................................................2Section 1: System Overview .........................................................................................................8Additional Detail on Key Components .........................................................................................9Hand-Held Controller (PE953) ................................................................................................924-Volt Valve Actuator (PE24VA) ............................................................................................9Water Temperature Sensor (PA122) .........................................................................................924-Volt Valve/Pump Switch (P4243ME) ................................................................................10Optional — Freeze (Air Temperature) Sensor (178PA28A) ....................................................10Section 2: Plumbing Examples ....................................................................................................11For Pool and Spa Combo Installations ........................................................................................11For Booster Pump Pool Cleaner Installations...............................................................................11For Non-Booster Pump Pool Cleaner Installations.......................................................................12Section 3: Installing and Wiring the PE653 Receiving Device ....................................................13Ratings .......................................................................................................................................13Wiring Instructions .....................................................................................................................14Power Connections ...............................................................................................................14Upper Terminal Connections .................................................................................................15Installation Instructions .........................................................................................................15List of Wiring Diagrams .........................................................................................................16Variable-Speed Pumps ...............................................................................................................17240V Variable-Speed Pump ...................................................................................................171-Speed Pumps ..........................................................................................................................18120V 1-speed pump ..............................................................................................................18120V 1-speed pump + any four 120 VAC auxiliary equipment ..............................................19120V 1-speed pump + 120 VAC blower or lights + 120V booster pump + 120V actuator + heater ....................................................................................................20120V 1-speed pump + 120V blower + 120V lights + 120V actuator + heater ........................21240V Pumps ..............................................................................................................................22240V 1-speed pump ..............................................................................................................22240V 1-speed pump + any four 240 VAC auxiliary equipment ..............................................23240V 1-speed pump + 240V blower + 240V booster pump + 240V actuator + heater ...........24240V 1-speed pump + 120V lights + 120V blower + 240V actuator + heater ........................25240V 2-Speed Pump .............................................................................................................26240V 2-speed pump + any three 240VAC auxiliary equipment .............................................27240V 2-Speed pump + any 3 120 VAC auxiliary equipment ..................................................28240V 2-Speed pump + 240V Booster Pump + 240V Actuator + Heater ................................29240V 2-speed pump + 120V lights + 240V blower + heater ..................................................30240V 2-speed pump + 240V blower + 240V actuator + heater ..............................................31240V 2-speed pump + 240V booster pump + 240V blower + heater .....................................32240V 2-speed pump + 240V booster pump + 120V light + heater .........................................33240V 2-speed pump + 240V booster pump + other 120 VAC equipment + heater .................34
Contents 5Providing a brighter solution.™Low-Voltage Wiring ...................................................................................................................35Water Temperature Sensor .....................................................................................................35Freeze/Air Temperature Sensor ...............................................................................................35Communications to a Variable-Speed Pump .........................................................................36Motorized Valve Actuator Connection and Synchronizing .....................................................36Fireman’s Switch Connection .....................................................................................................37Connection for Jandy Heaters ................................................................................................37Connection for Raypak Heaters .............................................................................................38Connection for Hayward Heaters ..........................................................................................38Connection for Pentair Heater ...............................................................................................39Connection for Sta-Rite / Pentair Heater with DDTC ..............................................................40Section 4: Programming the PE953 Hand-Held Controller .........................................................41Overview ...................................................................................................................................41Creating a Network Connection between the Hand-Held Controller and the PE653 Receiving Device .................................................................................................41Deleting Any Existing Programming .......................................................................................41Linking the Hand-Held Controller to the PE653 Receiving Device .........................................43Configuring for a 1-Speed or 2-Speed Pump ...............................................................................44Calibrating Pool, Spa and Air Temperature Settings .....................................................................44Configuring for a Booster (Cleaner) Pump ..................................................................................45Configuring the Fireman Switch Time Interval .............................................................................46Setting the Time of Day ..............................................................................................................47Setting Up Schedules .................................................................................................................47Configuring the Freeze Temperature (optional) ...........................................................................48Configuring for a Variable Speed Pump (optional) ......................................................................49Testing Z-Wave Reception ..........................................................................................................50Moving the Antenna to a Better Location ...............................................................................50Labeling for the PE653 Screen ...............................................................................................51Labeling for the Z-Wave Screen .............................................................................................51Labeling for the Variable-Speed Pump Screen ........................................................................51Labeling for the PE650 Screen ...............................................................................................51Section 5: Everyday Use of the Hand-Held Controller ...............................................................52Controlling the PE653 Receiving Device ....................................................................................53Operating Programmed Functions .........................................................................................53Changing between Pool and Spa ...........................................................................................53Setting Pool and Spa Temperatures.........................................................................................54Controlling a Variable-Speed Pump ............................................................................................54Naming the Speeds ...............................................................................................................54Changing Pump Speeds .........................................................................................................55Controlling Z-Wave Devices ......................................................................................................55Controlling PE650 Functions ......................................................................................................56Changing Batteries in the Hand-Held Controller ........................................................................56Manually Turning Equipment On and Off ..............................................................................57
6 Multi-Wave PE653-PE953 Installation GuideCopyright © 2010 Intermatic, Inc.Section 6:Advanced Features ......................................................................................................58Configuring Two or More Hand-Held Controllers ..................................................................58Changing a Secondary Remote Control into a Primary Control ..............................................60Including the PE953 Controller into a non-Multi-Wave (other manufacturer’s) network. ........61Section 7:Programming for Use with Z-Wave Home Control Devices ........................................62Deleting Any Existing Programming .......................................................................................62Including Z-Wave Devices into the Network .........................................................................63Including the PE653 Receiver onto a non-Multi-Wave remote controller ...............................63Adding Z-Wave Devices to Scenes for Everyday Control ........................................................64Renaming a Scene .................................................................................................................65Removing Z-Wave Devices from Scenes ................................................................................66Removing Z-Wave Devices from a Network ..........................................................................66Setting Up Z-Wave Associations with Capable Devices ........................................................67Removing Z-Wave Devices from an Association ...................................................................69Section 8:Using the PE953 with the PE650 Receiving Device .....................................................70Linking the PE953 Hand-Held Controller with the PE650 Receiving Device ..........................70Section 9: Checking Out and Verifying the System .....................................................................71Section 10: Troubleshooting ......................................................................................................75Section 11: Appendix ................................................................................................................80Glossary of Z-Wave Terminology ................................................................................................80FCC Statement ...........................................................................................................................81Section 12: Warranty .................................................................................................................82
7Providing a brighter solution.™Notes________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
8 Multi-Wave PE653-PE953 Installation GuideCopyright © 2010 Intermatic, Inc.Section 1: System OverviewThe Intermatic Multi-Wave Pool/Spa PE653RC Wireless Control System brings wireless control to a new level of simplicity and affordability. The following features make the system distinctive:Easy to Use — with simple, push button controls and a clear, easy-to-read display panel•Everything You Need — includes the functionality and control called for in nearly every •installation.Dependable — with Z-Wave• ® technology that lets you expand your system with inexpensive repeaters that plug into available electrical outlets to help extend the RF signal range of the entire system. Z-Wave technology eliminates intermittent signal problems experienced with many other systems.Cost Efficiency — a superior system, easier to install and maintain, with better •dependability, and at a cost that’s competitive with any other system available.The standard configuration for the Multi-Wave PE653RC Pool/Spa Wireless Control System configuration is shown in Figure 1-1. You can order individual components for a custom configuration or system as indicated. Z-Wave is a registered trademark of Sigma Designs and/or its subsidiaries.Figure 1-1Weatherproof outdoor enclosure can be mounted directly to an existing enclosure.Antenna can be remotely located using a Standard Cat 5 Ethernet cable with RJ45 plugs.Terminals for two-wire connections to remote temperature sensorsInternal selector switch for 120 / 240 VAC operationMetal Indoor/outdoor enclosureprovides for easy and securemounting and a large space forconduit wire connections.Receiving Device (PE653) Two-wire connection (RS485) forcontrol of variable-speed motorsApproved snap-in wiring separator for use with low voltage heater control circuitHand-Held Controller (PE953).Additional units can be ordered separately.Offers timer capability and can control up to five preprogrammed configurable circuits.Spare 0.10 Amp Fuse
One: System Overview 9Providing a brighter solution.™Additional Detail on Key ComponentsHand-Held Controller (PE953)The main function of the Hand-Held Controller is to transmit user commands to the PE653 Receiving Device, PE650 Receiving Device, and/or Z-Wave home control devices, and to display the status of the installed equipment.The unit floats if thrown in the pool or spa, is water-submersible, shock resistant, and requires three (3) AA batteries. Expected battery life is about one year in typical use.When the components of a specific system are linked together into a network, unique network ID codes supplied by the PE953 prevent unauthorized use of the system by neighboring systems.24-Volt Valve Actuator (PE24VA)Designed with quality in mind, Intermatic’s 24-volt valve actuators provide reliable control of 2-way and 3-way diverter valves for pool/spa combinations and water features. The water flow can be altered for specific applications through the adjustable cam, which rotates diverter valves to multiple degree settings. The cam settings can be easily adjusted by simply removing the lid. These valve actuators are compatible with all pool/spa valves currently offered in the industry and will retrofit into all pool/spa control systems.24VAC Input Voltage•Automates compatible diverter valves for •pool/spa combosAdjustable cam rotates diverter valves to •multiple degree settingsDesigned to operate most 2-way and 3-way diverter valves •Shipping Weight - 3 lbs. (1.4 kg) •Agency Approval - CSA/C-US•Water Temperature Sensor (PA122)The Intermatic Water Sensor (PA122) monitors both pool and spa water temperature, depending on the position of the diverter valves. Installation is necessary for the thermostatic control to work. The sensor can be ordered separately.ENTER
10 Multi-Wave PE653-PE953 Installation GuideCopyright © 2010 Intermatic, Inc.24-Volt Valve/Pump Switch (P4243ME)Designed as part of the Multi-Wave system and for aftermarket and retrofit applications, the P4243ME is most suited for controlling up to two different circuits associated with pool/spa combinations, but can also be used to control all the equipment typically needed in connection with water features, water gardening, solar heating, and other similar applications. This unit snaps into almost any Intermatic enclosure and controls pumps up to 3HP, 24 volt supply for up to three valve actuators, automated HIGH/LOW water temperature selector, heater connection circuit, and push-button control for each load with indicator lights on the face of the switch. In addition, the unit has connections for a hard-wired or wireless remote and a master switch controller. For this installation, if an enclosure must be added, we recommend Intermatic 2T2485GA.120 or 208-240 input voltage•Controls up to three valve actuators•Controls two circuits•Switches heater thermostat•Remote control capabilities•Shipping weight – 3 lb. (1.4 kg)•Agency approval – CSA/C-US•Contact Ratings — Each Circuit 17A Resistive, 120/240 VAC., 50/60 Hz•1.5 HP @ 120 VAC., 50/60 Hz•3.0 HP @ 240 VAC., 50/60 Hz•10 Amp Tungsten, 120/240 VAC., 50/60 Hz•Valve Actuator Supply: 24VAC 40VA•Optional — Freeze (Air Temperature) Sensor (178PA28A) Add the Intermatic Freeze or Air Temperature Sensor (178PA28A) to installations where below-freezing outdoor temperatures are a concern.
Two: Plumbing and Wiring Examples 11Providing a brighter solution.™Section 2: Plumbing ExamplesThe following diagrams show several plumbing and wiring examples of installations for pool and spa that share a single filter pump, filter, and heater. If you are installing a pool only or spa only, these diagrams will not apply.For Pool and Spa Combo Installations For Booster Pump Pool Cleaner Installations
12 Multi-Wave PE653-PE953 Installation GuideCopyright © 2010 Intermatic, Inc.For Non-Booster Pump Pool Cleaner InstallationsPool SpaFilterCheckValveSpa Make-upFilterPumpIntakeReturn ReturnIntakeHeaterEnergyFilter
Three: PE653 Receiving Device Installation 13Providing a brighter solution.™Section 3: Installing and Wiring the PE653 Receiving DeviceTo avoid fire, shock, or death, turn off power at circuit breaker and test that power is off before wiring.•Read instructions completely before installation and retain for future reference.•Observe all national and local electrical and safety codes.•Disconnect power when servicing or changing loads.•Alterations or modifications to the device will void the warranty.•For outdoor locations, rain-tight or wet location conduit hubs that comply with the requirements of UL 514B •Conduit, Tubing, and Cable Fittings, must be used. RatingsController Power In:120/240VAC, 50/60Hz - 5W MAX.•Contact Ratings: Load 1120/240 VAC•20A Resistive•17 Full load A, 80 Lock Rotor A•5A Tungsten or Ballast•Loads 2-5120/240 VAC•15A Resistive•10 Full load A, 60 Lock Rotor A•5A Tungsten or Ballast• • Figure 3-1 (PE653 Receiving Device)Include/Exclude Switch120 / 240 VAC Selector Switch Circuit ON/OFF SwitchesFuse (250 VAC - 0.1 A)Threaded Conduit Connection Bushing and HubAntenna SectionLoad ON indicator (Green LEDs) Low Voltage Divider (removable) Low Voltage Knockout AC Power Conduit openingWiring TerminalsAC Power & Status indicator (Red)Antenna Section Locking Screws
14 Multi-Wave PE653-PE953 Installation GuideCopyright © 2010 Intermatic, Inc.Wiring InstructionsPower Connections1- Speed Pump: Must be powered from •Terminal 3. 2-Speed Pump: Must be powered from •Terminal 3 for High-Speed and Terminal 4 for Low-Speed. Booster Pump: Must be powered from •Terminal 6.Actuator Control: Must be powered from •Terminal 7. Heater Control: Must be Terminals 8 & 9. •The metal enclosure must be ground bonded •in compliance with national, state and local codes.Terminal 1 must always be Neutral when using 120 VAC power. Terminal 1 must be L2 when using 240 VAC.Terminal 2 must always be Hot or L1 for both 120 VAC and 240 VAC.Terminal 3 must always be connected to the Hot terminal of the pump. Terminal 3 must always be connected to the HIGH SPEED terminal of a 2-speed pump.Terminal 4 must always be connected to the LOW SPEED terminal of a 2-speed pump when using a 2-speed motor.Terminal 5 is the input supply for both terminals 6 & 7. This terminal is rated at 15 A. maximum.Terminal 8 is the input supply for terminal 9. The load is rated at 15 A. maximum. Terminals 8 & 9 can be used for low voltage provided the Low Voltage Divider is used to separate the Low Voltage conductors from Line Voltage conductors. Low voltage conductors must exit the cabinet through a separate opening. (See Figure 3-1)Terminals 6 & 7 are function selectable with a maximum combined rating of 15 A.LOAD 1LOAD 2LOAD 3LOAD 4LOAD 5POWER IN & CONTROL POWER SUPPLYPOWER INPOWER IN112345= Circuit numberFigure 3-2 PE653 Master Control Center Power Terminal identificationCAUTION: The PE653 is a control device and NOT a safety disconnect. A proper sized fused disconnect or breaker of no more than 125 Amp capacity must be provided in the power supply circuit. Proper gauge wire should be based on local code requirements of amperage and wire length.Manual ON/OFF SwitchesAC POWER & STATUS indicatorINCLUDE/EXCLUDE switch
Three: PE653 Receiving Device Installation 15Providing a brighter solution.™Upper Terminal ConnectionsInstallation Instructions To avoid fire, shock, or death, turn off power at circuit breaker and test that power is off 1. before wiring. Select a location for the installation that is near the pool/spa equipment; at least five (5) feet 2. distance or more from either the pool or spa and at least five (5) feet above ground level. The PE653 must be mounted in a vertical (upright) position on the top of the enclosure.Select the knockouts to be used. Remove the inner 1/2” knockout by inserting a flathead 3. screw driver in the slot and carefully punch the knockout loose and remove the slug. If a 3/4’ knockout is required, remove the outer ring with pliers after removing the 1/2” knockout. Smooth the edge with a file if required.Place the metal enclosure in the desired mounting location and mark the three mounting 4. holes. Install the top screw first and then hang the enclosure by the keyhole. Then install the bottom screws, tightening all screws for a secure mounting.Install electrical conduit as needed to comply with all national and local electrical and safety 5. codes.If a low voltage circuit or a heater control circuit is to be used, remove the low voltage 6. knockout from the PE653 enclosure.Install electrical conduit as required by national, state and local codes. 7. Bond the enclosure in accordance with your state and local codes. Where required, 8. connect a No. 8 AWG solid copper wire to the enclosure using Bonding Lug (part number 156T11047A). Connect the bonding wire to an approved earth ground.Identify and install all wires necessary to complete the installation. Allow a length of 9. approximately 18” of each wire at the metal enclosure for required connections of junctions. Connect wiring for circuits as required. Refer to the diagrams in this section for wiring 10. suggestions for specific equipment combinations. All splices and wire nut connections should be in the metal enclosure, not in the PE653 enclosure. Check and tighten all connections and circuits. 11. Apply power.12. Figure 3-3 PE653 Master Control Center Upper Terminal identificationLocal Antenna ConnectorAir Sensor (178PA28A)Water Sensor (PA122) Solar Sensor (PA122)Remote Antenna ConnectorSerial Connection (RS485)NOTE: Observe polarity when connecting pump manufacturer’s cable to the Serial connection.THE METAL ENCLOSURE MUST BE CLOSED AND SECURED WITH A LOCK OR TY-WRAP.
16 Multi-Wave PE653-PE953 Installation GuideCopyright © 2010 Intermatic, Inc.Variable-Speed Pumps240V Variable-Speed Pump ......................................................................................................... Figure 3-4One-Speed Pumps120V 1-Speed Pump ................................................................................................................... Figure 3- 5120V 1-Speed pump + any 4 120 VAC auxiliary equipment ........................................................ Figure 3- 6120V 1-Speed pump + 120V Blower or Lights + 120V Booster Pump + 120V Actuator + Heater Figure 3-7120V 1-Speed pump + 120V Lights + 120V Blower + 120V Actuator + Heater ........................... Figure 3-8240V 1-Speed Pump ................................................................................................................... Figure 3-9240V 1-Speed pump + any 4 240 VAC auxiliary equipment ........................................................ Figure 3-10240V 1-Speed pump + 240V Blower + 240V Booster Pump + 240V Actuator + Heater ............... Figure 3-11240V 1-Speed pump + 120V Lights + 120V Blower + 240V Actuator + Heater ........................... Figure 3-12Two-Speed Pumps240V 2-Speed Pump ................................................................................................................... Figure 3-13240V 2-Speed pump + any 3 240 VAC auxiliary equipment ........................................................ Figure 3-14240V 2-Speed pump + any 3 120 VAC auxiliary equipment ........................................................ Figure 3-15240V 2-Speed pump + 240V Booster Pump + 240V Actuator + Heater ....................................... Figure 3-16240V 2-Speed pump + 120V Lights + 240V Blower + Heater ...................................................... Figure 3-17240V 2-Speed pump + 240V Blower + 240V Actuator + Heater .................................................. Figure 3-18240V 2-Speed pump + 240V Booster pump + 240V Blower + Heater ......................................... Figure 3-19240V 2-Speed pump + 240V Booster pump + 120V Light + Heater ............................................. Figure 3-20240V 2-Speed pump + 240V Booster pump + other 120 VAC equipment + Heater ..................... Figure 3-21List of Wiring Diagrams
Three: PE653 Receiving Device Installation 17Providing a brighter solution.™Variable-Speed Pumps240V Variable-Speed PumpFigure 3-4
18 Multi-Wave PE653-PE953 Installation GuideCopyright © 2010 Intermatic, Inc.1-Speed Pumps120V 1-speed pumpFigure 3-5
Three: PE653 Receiving Device Installation 19Providing a brighter solution.™120V 1-speed pump + any four 120 VAC auxiliary equipmentFigure 3-6
20 Multi-Wave PE653-PE953 Installation GuideCopyright © 2010 Intermatic, Inc.120V 1-speed pump + 120 VAC blower or lights + 120V booster pump + 120V actuator + heaterFigure 3-7
Three: PE653 Receiving Device Installation 21Providing a brighter solution.™120V 1-speed pump + 120V blower + 120V lights + 120V actuator + heaterFigure 3-8
22 Multi-Wave PE653-PE953 Installation GuideCopyright © 2010 Intermatic, Inc.240V Pumps240V 1-speed pumpFigure 3-9
Three: PE653 Receiving Device Installation 23Providing a brighter solution.™240V 1-speed pump + any four 240 VAC auxiliary equipmentFigure 3-10
24 Multi-Wave PE653-PE953 Installation GuideCopyright © 2010 Intermatic, Inc.240V 1-speed pump + 240V blower + 240V booster pump + 240V actuator + heaterFigure 3-11
Three: PE653 Receiving Device Installation 25Providing a brighter solution.™240V 1-speed pump + 120V lights + 120V blower + 240V actuator + heaterFigure 3-12
26 Multi-Wave PE653-PE953 Installation GuideCopyright © 2010 Intermatic, Inc.240V 2-Speed PumpFigure 3-13
Three: PE653 Receiving Device Installation 27Providing a brighter solution.™240V 2-speed pump + any three 240VAC auxiliary equipmentFigure 3-14
28 Multi-Wave PE653-PE953 Installation GuideCopyright © 2010 Intermatic, Inc.240V 2-Speed pump + any 3 120 VAC auxiliary equipmentFigure 3-15

Navigation menu