Intermec Technologies 1555-2450 Hand Held Tag Reader User Manual getting started

Download:
Mirror Download [FCC.gov]
Document ID	136129
Application ID	Pva6ewR6JhP6zfGGhIdc3Q==
Document Description	User manual getting started
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	76.57kB (957142 bits)
Date Submitted	2001-02-12 00:00:00
Date Available	2001-05-24 00:00:00
Creation Date	2000-08-22 10:42:44
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2000-08-22 10:42:44
Document Title	User manual getting started

Getting Started Guide
P/N x-xxxx49-01
Sabre 1555 Laser Scanner
& RFID Reader/Programmer
Guía de Iniciación
Guida Introduttiva
Guide de Démarrage
Guia de Iniciação
Anleitung für Einsteiger
Introduction
Use this Getting Started Guide to set up the Sabre 1555 laser scanner and RFID reader/
programmer for most terminal connections and symbologies. If necessary, use the
EasySet setup software or Installation Manual for additional configuration possibilities
and terminal connections.
Basic setup
Getting Started Guide
Configuración básica
Configuration de base
Grundkonfiguration
Configurazione di base
EasySet
Full setup
EasySet setup software
Configuración completa
Configuration complète
Installation Manual
Vollständige Konfiguration
Configurazione completa
Configuração completa
(on the CD-ROM or to order)
Operating
Operator’s Guide
Uso
Utilisation
Betrieb
Utilizzazione
Interactive Programming
Interactive Programming
Guide
(need translations to other
languages)
Connect scanner cable (standard version shown)
Scanner cable depends
on your terminal
Cables
Accessories
RFID reader/programmer operation
"beep"
RFID reader/programmer reading distance
Sabre 1555
2450 MHz
1 cm - 60 cm
(0.4" - 24")
Sabre 1555
915 MHz
2.5 cm - 200 cm
(1" - 80")
Scanner operation
"beep"
Scanner reading distance
Sabre 1555
Standard Range
6 cm - 34 cm
(2.5" - 13.5")
Sabre 1555
Long Range
28 cm - 100 cm
(11" - 39")
RS-232 C
Ê
System power OFF
Ë
Connect cable
Direct RS-232 C cable
P/N 3-604032-00
Ì
Scanner power ON
Í
System power ON
Î
Select standard RS-232 C
(PC serial port compatible)
9600 baud, 7 data bits, even parity, 2 stop bits
postamble = carriage return + line feed
Ï
Customize parameters (optional)
(*) = default value
9600 baud (*)
19200 baud
7 data bits (*)
8 data bits
Even parity (*)
Odd parity
No parity
Postamble = Carriage Return + Line Feed (*)
Postamble = Carriage Return
Postamble = none
RS-232 TTL
Ê
System power OFF
Ë
Connect cable
Ì
Scanner power ON
Í
System power ON
Î
Select RS-232 TTL
Direct RS-232 TTL cable
P/N x-xxxxxx-xx
9600 baud, 7 data bits, even parity, 2 stop bits
postamble = carriage return + line feed
Ï
Customize parameters (optional)
(*) = default value
9600 baud (*)
19200 baud
7 data bits (*)
8 data bits
Even parity (*)
Odd parity
No parity
Postamble = Carriage Return + Line Feed (*)
Postamble = Carriage Return
Postamble = none
Universal Serial Bus (USB)
Ê
System power OFF
Ë
Connect cable
Direct USB cable
P/N x-xxxxxx-xx
Ì
Scanner power ON
Í
System power ON
Î
Select standard USB
(PC serial port compatible)
9600 baud, 7 data bits, even parity, 2 stop bits
postamble = carriage return + line feed
10
Ï
Customize parameters (optional)
(*) = default value
Intermec representative needs to supply USB symbologies when
the symbols are available.
11
Symbology
Ê Disable all symbologies
Ë
Select symbology
Code 39
UPC-A, UPC-E, EAN-8, EAN-13
(UPC-A -> EAN-13)
Code 128 / EAN 128
Ì
UPC-A, UPC-E, EAN-8, EAN-13
(UPC-A -> UPC-A)
Test
Code 39
UPC-A
CODE-39
Code 128
CODE-128
EAN 13
1234567890128
12
Reset
Online setup
Ê
Ë
System power OFF
Connect RS-232 C cable
(P/N 3-604032-00)
Ì
Scanner power ON
Í
System power ON
Î
Scan EasySet setup code
EasySet
Ï
Start EasySet software
13
Laser warnings
The Sabre 1555 has a maximum laser output of 1mW at 630-680 nm and complies with the following safety
standards:
USA: CDRH - Class II Laser Product (CFR 21 Subpart J)
IEC 825-1 EN 60825-1 - Class 2 Laser Product
Fix these warning labels onto the product if they are not already present.
Collez les étiquettes d’avertissement sur votre produit. Cole as etiquetas de precaução no equipamento.
Bringen Sie Warnetiketten auf dem Produkt an.
Un’etichetta di avviso per il laser è da applicare sul prodotto.
Fije la etiqueta de advertencia en el producto.
CAUTION – Use of controls or adjustments or performance of procedures other than those specified herein result in
hazardous laser light.
VORSICHT – Bei einer anders als hier beschriebenen Verwendung der Bedienelemente oder Veränderungen oder
einer anderen Ausführung der Arbeitsabläufe entsteht gefährliches Laserlicht.
ATTENTION – L’utilisation de contrôles/commandes ou de réglages ou l’exécution de procédures autres que ceux
précisés par le présent document provoquent une lumière laser dangereuse.
14
Regulatory statements
USA & Canada: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
This device requires a radio license, unless it is used totally inside of a building. (The user must obtain this license.)
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Cet appareil exige une
license radio à moins d’être entièrement installé dans un bâtiment. (L’utilisateur doit obtenir cette license.)
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
This equipment is intended for operation in a commercial environment, in compliance with the requirements for a Class A digital device, pursuant
to Part 15 of the FCC Rules, and it must not be used in a residential environment. It generates, uses, and can radiate radio frequency energy. If
not installed and used in accordance with the instruction manual, it may cause interference to radio communications. If this equipment causes
interference, the user will be required to correct the interference at the user’s own expense.
To maintain compliance with the FCC Rules, the input/output (I/O) cables that interconnect between the device and any peripheral (such as a
reader) must be as specified by Intermec.
Operator Warning: FCC regulations limit exposure to radio frequency (RF) radiation. To comply with these regulations, the operator of this
device must maintain a distance of at least 4 cm (2 inches) from the front part of the device to any bystanders under normal operating conditions.
While the device is on, the operator’s body and parts of the body, such as eyes, hands, or head, must be 4 cm (2 inches) or farther
from the front of the device.
This device is UL listed (UL 1950/C22.2 No. 950) for safety when powered by a host system or by one of the following external Intermec power
supplies: Catalog No. and P/N 043230 ~100V, 50/60 Hz or Catalog No. and P/N 047793 ~120V, 60 Hz. The device is CSA certified.
Intermec hereby declares that the Sabre 1555 has been tested and found compliant with the below listed standards as required by the
EMC Directive 89/336/EEC as amended by 92/31/EEC and by the Low Voltage Directive 73/23/EEC as amended by 93/68/EEC:
EN55022, EN50082-2, EN60950
This device is TÜV GS licensed (EN 60950 and EN 60825-1) for safety when powered by a host system or by the following external Intermec power
supply: Catalog No. and P/N 047795 ~230V, 50 Hz. For 240V applications use the power supply: Catalog No. 047794 (P/N 5014UK) ~240V, 50
Hz.
Australia-New Zealand: This equipment has been tested and found to conform to the Australian EMC framework concerning
Class
digital
standard AS/NZS 3548.
devices,
prescribed
by
the
Australian
and
New
Zealand
N309
Mexico: Este equipo cumple con la certificatión NOM.
The information contained in this document is for informational purposes only and is subject to change without notice. No part of this document
may be copied or reproduced in any manner without the prior written permission of Intermec Technologies Corporation.
Sabre products are covered by patents issued or pending in the USA and other countries.
The word Intermec, the Intermec logo, Sabre and EasySet are either trademarks or registered trademarks of Intermec.
Throughout this document, trademarked names may be used. Rather than put a trademark (™ or ®) symbol in every occurrence of a trademarked
name, we state that we are using the names only in an editorial fashion, and to the benefit of the trademark owner, with no intention of infringement.
Caution
Changes or modifications not expressly approved by Intermec could void the user's authority to operate this equipment.
North America / Asia Pacific / Latin America • 6001 36th Avenue West, PO Box 4280, Everett, WA 98203-9280
Tel: +1 425 348 2600 • Fax: +1 425 348 2833 • U.S. service and technical support, tel: 1.800.755.5505 • Canadian
service and technical support, tel: 1.800.688.7043
Europe / Middle East / Africa • Sovereign House, Vastern Road, Reading RG1 8BT, England
Tel: +44 118 987 9420 • Fax: +44 118 987 9416
Internet: http://www.intermec.com
E-mail: info@intermec.com
Support: http://datacapture.intermec.com
© 09/00 Intermec Technologies Corporation.
All rights reserved.
15
Edition
1.0


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Create Date                     : 2000:08:22 10:42:44
Producer                        : Acrobat Distiller 4.0 for Windows
Modify Date                     : 2000:08:22 10:42:44-06:00
Page Count                      : 16

EXIF Metadata provided by EXIF.tools