Intermec Technologies 802UIAG 802UIAG User Manual CK60UserManual WinCE

Intermec Technologies Corporation 802UIAG CK60UserManual WinCE

UserManual.wiki >

Intermec Technologies >

802UIAG User Manual >

Users Manual

ContentsCK60 Handheld Computer with Windows CE User’s Manual iiiContentsBefore You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ixSafety Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ixSafety Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xGlobal Services and Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiWho Should Read this Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiRelated Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiiPatent Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii1 Using the CK60 Handheld Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Introducing the CK60 Handheld Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Learning Software Build Versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Resetting Your CK60 Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Performing a Warm-Boot on the CK60 Computer. . . . . . . . . . . . . . . . . . . . . . . . . 3Performing a Cold-Boot on the CK60 Computer. . . . . . . . . . . . . . . . . . . . . . . . . . 3Scanning Bar Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Scanning with the 2D Area Imager. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Supported Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Using the Ambient Light Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Using the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Changing and Installing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Maximizing Battery Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Checking the Battery Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Using the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 832-Key Large Numeric Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 945-Key Full Alphanumeric Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 958-Key Full Alphanumeric Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Using the Color-Coded Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Capitalizing All Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Typing Alphabetical Characters on the 45-Key Keypad . . . . . . . . . . . . . . . . . . . . 11Using the Power (I) Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Turning on the Keypad Backlight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Using the Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Using the Speakers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Enabling the Speaker and Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . 13Disabling the Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Using the Status Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Using the Secure Digital Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Physical and Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Contentsiv CK60 Handheld Computer with Windows CE User’s ManualAccessories for the CK60 Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Windows CE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Basic Skills. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Desktop Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Start Menu and Task Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Notifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Entering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Large Keys Versus Small Keys on Keyboard. . . . . . . . . . . . . . . . . . . . . . . 22Typing With the Onscreen Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Using Transcriber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Selecting Typed Text. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Finding and Organizing Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Customizing Your CK60 Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Adding Programs Using Microsoft ActiveSync . . . . . . . . . . . . . . . . . . . . 24Adding a Program Directly from the Internet . . . . . . . . . . . . . . . . . . . . . 25Adding a Program to the Start Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Removing Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Microsoft ActiveSync. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26IConnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Internet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Ethernet Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28For 802.11b/g Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29iFTP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Getting Connected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Connecting to an Internet Service Provider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Direct Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Ending a Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Internet Explorer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Viewing Mobile Favorites and Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Browsing the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343 Configuring the CK60 Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Developing Applications for the CK60 Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Converting Older Computer Applications to CK60 Applications . . . . . . . . . . . . . . . . . . . 38Packaging Applications for the CK60 Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Installing Applications on the CK60 Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Installing Applications Using Microsoft ActiveSync . . . . . . . . . . . . . . . . . . . . . . . 40Installing Applications Using a Secure Digital Card . . . . . . . . . . . . . . . . . . . . . . . 41

ContentsCK60 Handheld Computer with Windows CE User’s Manual vLaunching Your Application Automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42PreShell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42PostShell. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42RunAutoRun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43AutoExec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44AutoRun. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46AutoCopy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46AutoReg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47AutoCab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47Customizing How Applications Load on the CK60 Computer . . . . . . . . . . . . . . . . . . . . . 48Configuring CK60 Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Configuring with the Setup Assistant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Synchronizing the CK60 Computer System Time with a Time Server . . . . . . . . . 50Configuring the CK60 Computer through the Network . . . . . . . . . . . . . . . . . . . 50Configuring the CK60 Computer in a TCP/IP Direct Connect Network . . . . . . 50Configuring the CK60 Computer in a UDP Plus Network . . . . . . . . . . . . . . . . . 52Configuring the CK60 Computer for Your Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Configuring Serial Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Configuring 802.11b/g Radio Communications. . . . . . . . . . . . . . . . . . . . . . . . . . 53Configuring the Network Parameters for a TCP/IP Network . . . . . . . . . . . . . . . . 54Configuring the Network Parameters for a UDP Plus Network . . . . . . . . . . . . . . 54Configuring Ethernet Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Configuring Bluetooth Radio Communications . . . . . . . . . . . . . . . . . . . . . . . . . . 54Local Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Wireless Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Bluetooth DUN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Configuring the SF51 Scanner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Enabling Bluetooth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Creating an SF51 Connection Label. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Viewing SF51 Scanner Information from Your CK60 Computer. . . . . . . . . . . . . 63Configuring Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Loading Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Terminology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Configuring Your Wireless Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Advanced. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88Using Configuration Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90Using Reader Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91Change Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91Set Time and Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Contentsvi CK60 Handheld Computer with Windows CE User’s Manual4 Maintaining the CK60 Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93Upgrading the Operating System on your CK60 Computer . . . . . . . . . . . . . . . . . . . . . . . 94Running Diagnostics on Your CK60 Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94Frontlight Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94Battery Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94Display Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95Hardware Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96Keyboard (Keypad) Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96LED Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97Memory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97Networking Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98Read CPU Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98Sound Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99Touch Screen Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99Software Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100Troubleshooting Your CK60 Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100Cleaning the Scanner Window and CK60 Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1075 Network Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109Ethernet Communications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110Wireless 802.11 Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110AutoIP/DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1116 Bar Code Symbologies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113Codabar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114Codablock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114Codablock A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115Codablock F. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115Code 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115Code 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115Code 39 Full ASCII Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116Concatenated Code 39 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116Code 93. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116Code 128. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116Data Matrix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

ContentsCK60 Handheld Computer with Windows CE User’s Manual viiEAN (European Article Numbering) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118EAN/UCC (Uniform Code Council) Composite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118Interleaved 2 of 5 (I 2 of 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119Matrix 2 of 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119MaxiCode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119Micro PDF417 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119MSI Code (Variant of Plessey). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120PDF417. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120Plessey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120QR Code (Quick Response Code). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121RSS (Reduced Space Symbology) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121RSS 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121RSS Expanded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121RSS Limited . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121Telepen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122UPC (Universal Product Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Contentsviii CK60 Handheld Computer with Windows CE User’s Manual

Before You BeginCK60 Handheld Computer with Windows CE User’s Manual ixBefore You BeginThis section provides you with safety information, technical support infor-mation, and sources for additional product information.Safety SummaryYour safety is extremely important. Read and follow all warnings and cau-tions in this document before handling and operating Intermec equipment. You can be seriously injured, and equipment and data can be damaged if you do not follow the safety warnings and cautions.Do not repair or adjust aloneDo not repair or adjust energized equipment alone under any circum-stances. Someone capable of providing first aid must always be present for your safety.First aidAlways obtain first aid or medical attention immediately after an injury. Never neglect an injury, no matter how slight it seems.ResuscitationBegin resuscitation immediately if someone is injured and stops breathing. Any delay could result in death. To work on or near high voltage, you should be familiar with approved industrial first aid methods.Energized equipmentNever work on energized equipment unless authorized by a responsible authority. Energized electrical equipment is dangerous. Electrical shock from energized equipment can cause death. If you must perform authorized emergency work on energized equipment, be sure that you comply strictly with approved safety regulations.

Before You Beginx CK60 Handheld Computer with Windows CE User’s ManualSafety IconsThis section explains how to identify and understand dangers, warnings, cautions, and notes that are in this manual. You may also see icons that tell you when to follow ESD procedures and when to take special precautions for handling optical parts...A warning alerts you of an operating procedure, practice, condition, or statement that must be strictly observed to avoid death or serious injury to the persons working on the equipment.Avertissement: Un avertissement vous avertit d’une procédure de fonctionnement, d’une méthode, d’un état ou d’un rapport qui doit être strictement respecté pour éviter l’occurrence de mort ou de blessures graves aux personnes manupulant l’équipement.A caution alerts you to an operating procedure, practice, condition, or statement that must be strictly observed to prevent equipment damage or destruction, or corruption or loss of data.Attention: Une précaution vous avertit d’une procédure de fonctionne-ment, d’une méthode, d’un état ou d’un rapport qui doit être stricte-ment, respecté pour empêcher l’endommagement ou la destruction de l’équipement, ou l’altération ou la perte de données.Note: Notes either provide extra information about a topic or contain spe-cial instructions for handling a particular condition or set of circumstances.

Before You BeginCK60 Handheld Computer with Windows CE User’s Manual xiGlobal Services and SupportWarranty InformationTo understand the warranty for your Intermec product, visit the Intermec web site at www.intermec.com and click Service & Support. The Intermec Global Sales & Service page appears. From the Service & Support menu, move your pointer over Support, and then click Warranty.Disclaimer of warranties: The sample code included in this document is presented for reference only. The code does not necessarily represent com-plete, tested programs. The code is provided as is with all faults." All war-ranties are expressly disclaimed, including the implied warranties of merchantability and fitness for a particular purpose.Web SupportVisit the Intermec web site at www.intermec.com to download our current manuals in PDF format. To order printed versions of the Intermec manu-als, contact your local Intermec representative or distributor.Visit the Intermec technical knowledge base (Knowledge Central) at intermec.custhelp.com to review technical information or to request tech-nical support for your Intermec product.Telephone SupportThese services are available from Intermec Technologies Corporation.Outside the U.S.A. and Canada, contact your local Intermec representative. Click Contact from the Intermec web site to search for your representative.Who Should Read this ManualThis manual provides information on CK60 features, and how to install, configure, operate, maintain, and troubleshoot the CK60 Computer.Services DescriptionIn the USA and Canada call 1-800-755-5505 and choose this optionFactory Repair and On-site RepairRequest a return authorization number for authorized service center repair, or request an on-site repair technician.1Technical Support Get technical support on your Intermec product. 2Service Contract Status Inquire about an existing contract, renew a contract, or ask invoicing questions.3Schedule Site Surveys or InstallationsSchedule a site survey, or request product/system installation. 4Ordering Products Talk to sales administration, place an order, or check the sta-tus of your order.5

Before You Beginxii CK60 Handheld Computer with Windows CE User’s ManualRelated DocumentsThis table contains a list of related Intermec documents and part numbers. The Intermec web site at www.intermec.com contains our documents that you can download in PDF format. To order printed versions of the Inter-mec manuals, contact your local Intermec representative or distributor.Patent InformationThis product is protected by one or more of the following patents: 4,882,476; 4,894,523; 4,953,113; 4,961,043; 4,970,379; 4,988,852; 5,019,699; 5,021,642; 5,038,024; 5,081,343; 5,095,197; 5,144,119; 5,144,121; 5,182,441; 5,187,355; 5,187,356; 5,195,183; 5,195,183; 5,195,183; 5,216,233; 5,216,550; 5,218,191; 5,227,614; 5,233,172; 5,241,488; 5,243,602; 5,258,606; 5,278,487; 5,288,985; 5,308,966; 5,322,991; 5,331,136; 5,331,580; 5,342,210; 5,349,678; 5,359,185; 5,371,858; 5,373,478; 5,389,770; 5,397,885; 5,410,141; 5,414,251; 5,416,463; 5,442,167; 5,464,972; 5,468,947; 5,468,950; 5,477,044; 5,486,689; 5,488,575; 5,500,516; 5,502,297; 5,504,367; 5,508,599; 5,514,858; 5,530,619; 5,534,684; 5,536,924; 5,539,191; 5,541,419; 5,548,108; 5,550,362; 5,550,364; 5,565,669; 5,567,925; 5,568,645; 5,572,007; 5,576,529; 5,592,512; 5,594,230; 5,598,007; 5,608,578; 5,616,909; 5,619,027; 5,627,360; 5,640,001; 5,657,317; 5,659,431; 5,671,436; 5,672,860; 5,684,290; 5,719,678; 5,729,003; 5,742,041; 5,761,219; 5,764,798; 5,777,308; 5,777,309; 5,777,310; 5,786,583; 5,793,604; 5,798,509; 5,798,513; 5,804,805; 5,805,807; 5,811,776; 5,811,777; 5,818,027; 5,821,523; 5,828,052; 5,831,819; 5,834,749; 5,834,753; 5,837,987; 5,841,121; 5,842,070; 5,844,222; 5,854,478; 5,862,267; 5,869,840; 5,873,070; 5,877,486; 5,878,395; 5,883,492; 5,883,493; 5,886,338; 5,889,386; 5,895,906; 5,898,162; 5,902,987; 5,902,988; 5,912,452; 5,923,022; 5,936,224; 5,949,056; 5,969,321; 5,969,326; 5,969,328; 5,979,768; 5,986,435; 5,987,192; 5,992,750; 6,003,775; 6,012,640; 6,016,960; 6,018,597; 6,024,289; 6,034,379; 6,036,093; 6,039,252; 6,064,763; 6,075,340; 6,095,422; 6,097,839; 6,102,289; 6,102,295; 6,109,528; 6,119,941; 6,128,414; 6,138,915; 6,149,061; 6,149,063; 6,152,370; 6,155,490; 6,158,661; 6,164,542; 6,164,545; 6,173,893; 6,195,053; 6,234,393; 6,234,395; 6,244,512; 6,249,008; 6,328,214; 6,330,975; 6,345,765; 6,356,949; 6,367,699; 6,375,075; 6,375,076; 6,431,451; 6,435,411; 6,484,944; 6,488,209; 6,497,368; 6,532,152; 6,538,413; 6,539,422; 6,621,942; 6,641,046; 6,681,994; 6,687,403; 6,688,523; 6,732,930; Des. 417445There may other U.S. and foreign patents pending.Document Title Part NumberCK60 Handheld Computer Quick Start Guide 962-054-115Intermec Computer Command Reference Manual 073529TE 2000 VT/ANSI Terminal Emulation Programmer’s Guide 977-055-005TE 2000 5250 Terminal Emulation Programmer’s Guide 977-055-004TE 2000 3270Terminal Emulation Programmer’s Guide 977-055-003

CK60 Handheld Computer with Windows CE User’s Manual 11Using the CK60 Handheld ComputerThis chapter introduces the CK60 Handheld Computer, developed by Intermec Technologies Corporation to enhance wireless connectivity needs and contains hardware and software configuration information to assist you in making the most out of your CK60 Computer.• Learning Software Build Versions (page 3)•Resetting Your CK60 Computer (page 3)• Scanning Bar Codes (page 4)• Using the Ambient Light Sensor (page 5)• Using the Battery (page 6)• Using the Keypad (page 8)• Using the Screen (page 12)• Using the Speakers (page 13)• Using the Status Lights (page 14)• Using the Secure Digital Card (page 15)Note: Desktop icons and control panel applet icons are shown to the left. Any place that Start is mentioned, tap the following Windows icon in the bottom, left corner of your CK60 desktop.

Chapter 1 — Using the CK60 Handheld Computer2 CK60 Handheld Computer with Windows CE User’s ManualIntroducing the CK60 Handheld ComputerThe Intermec CK60 Handheld Computer is an ergonomically designed handheld computer built on the Microsoftr Windowsr CE operating sys-tem. It is a lightweight, easy-to-use, reliable computer that runs client/server applications, terminal emulation applications, as well as browser-based applications.The CK60 Computer is available with the following:•Ethernet• 802.11b/g radio• Bluetooth - *Bluetooth is a trademark owned by Bluetooth SIG, Inc., USA• 64MB or 128MB RAM/64MB Flash Memory• Disk on Chip (128MB)• 2D Area Imager• EV10 ImagerUse this manual to understand how to use the features and options avail-able on the CK60 Computer.CK60 Computers with an IEEE 802.11b/g radio installed are Wi-Fir certi-fied for interoperability with other 802.11b/g wireless LAN devices.EnterBattery statusMicrophoneMicrophoneScan buttonIntermec Ready-To-Work Good read lightIndicatorFront Speaker Scan buttonKeyboard function

Chapter 1 — Using the CK60 Handheld ComputerCK60 Handheld Computer with Windows CE User’s Manual 3Learning Software Build VersionsThe Persistent Storage Manager (PSM) is an area of storage which is embedded in a section of the system’s FLASH memory. This storage area is not erased when a cold-boot is performed. It may, however, be erased dur-ing the reflashing process. In addition to storing applications and data files, you do have the option to store a persistent registry to the PSM region.Resetting Your CK60 ComputerYou seldom need to perform a warm-boot or a cold-boot on the CK60 Computer. The CK60 Computer currently uses the configuration currently saved in flash memory during the boot process.In some cases where the CK60 Computer completely stops responding, an application is locked up and does not respond, when you upgrade the firm-ware, or when you reflash the CK60 Computer, it may be necessary to per-form either a warm-boot or a cold-boot.Performing a Warm-Boot on the CK60 ComputerIf your charged CK60 Computer does not resume after pressing I, or if the computer or an application is locked up, you may need to do a warm-boot.•Press and hold I for ten seconds. The CK60 Computer tells you it is performing a warm-boot, then comes back up to the start screen.Performing a Cold-Boot on the CK60 ComputerIf the CK60 Computer or an application is locked up and does not respond to a warm-boot, do the following.1Release the lower clip of the hand strap.To check to see if your CK60 Computer has the latest PSM build or the latest operating system build, double-tap the Internet Explorer icon from the desktop, then scroll down for the latest information displayed beneath the CK60 Version Information title.

Chapter 1 — Using the CK60 Handheld Computer4 CK60 Handheld Computer with Windows CE User’s Manual2Remove the battery pack.3Press the reset button (shown in the following illustration).4Reinstall the battery pack.Scanning Bar CodesUse the scanner to scan and enter bar code data. The type of scanner you are using and the type of bar code you are decoding determines the way you scan the bar code. The CK60 Computer supports the scanning of 2D images. Plus, if you are using an integrated handle or a tethered scanner, the way you scan bar codes is different.When you unpack the CK60 Computer, these bar code symbologies are enabled:•Code39•UPC/EAN• PDF417 (if supported)If you are using bar code labels that are encoded in a different symbology, you need to enable the symbology on the computer.Scanning with the 2D Area ImagerThe CK60 Computer has the 2D area imager, which provides the ability to scan 2D bar code symbologies and supports omni-directional (360°) scan-ning where you can position the CK60 Computer in any orientation to scan a bar code label. Using the 2D area imager is very similar to taking a picture with a digital camera.Do not look directly into the window area or at a reflection of the laser beam while the laser is scanning. Long-term exposure to the laser beam can damage your vision.Avertissement: Ne regardez pas directement la réflexion d’un rayon laser ou dans la fenêtre du laser lorsque celui-ci est en opération. Si vous regardez trop longtemps un rayon laser, cela peut endommager votre vue. Press this reset button with your stylus.Do not use force or a sharp object when pressing the reset button. Youmay damage the reset button.

Chapter 1 — Using the CK60 Handheld ComputerCK60 Handheld Computer with Windows CE User’s Manual 5To scan a bar code label with the 2D area imager1Press I to turn on the CK60 Computer.2Point the scanner window at the bar code label and hold the CK60 Computer steady a few inches from the label.3Press the Scan button on the keypad or pull the trigger on a handle and center the red aiming beam over the bar code label.The aiming beam is smaller when the imager is closer to the bar code and larger when it is further away.When the CK60 Computer successfully reads a bar code label, you hear a high beep and the green Good Read light turns on briefly.4Release the Scan button.Supported DevicesThe CK60 Computer should connect the following scanner models: 1551, 1553, 1555; ScanPlus 1800SR, 1800ST, 1800VT; Scan Image 1470; SR1 and SG1, SF51. There are a number of different scan engines covered by these models, including RFID and XLR scan engines. Model 1555 and Scan Image 1470 are supported as input devices only; configuration of these models are accomplished by scanning labels. Using the Ambient Light SensorThe ambient light sensor automatically turns off the display lighting as sur-rounding light increases to conserve your CK60 Computer battery power.As configured from the factory, the ambient light sensor is disabled. To enable the ambient light sensor and change its settings, tap Start > Settings > Control Panel. Double-tap the Backlight icon, then tap the right arrow to scroll to and tap the Both Power tab. Make your selections, then tap OK to exit this applet.This assumes the backlight setting once the CK60 Computer is powered on.This turns off the ambient light sensor.With this, the backlight is disabled in normal environments.With this, the backlight is disabled in bright environments.

Chapter 1 — Using the CK60 Handheld Computer6 CK60 Handheld Computer with Windows CE User’s ManualUsing the BatteryThe CK60 Computer uses a 17.3 Watt-hour, 7.2V, replaceable Lithium-Ion (LiIon) battery. You must fully charge the main battery before you can use the CK60 Computer. When you change the battery, a backup battery (super capacity) maintains your status, memory, and real-time clock for at least 10 minutes.Dispose of used battery packs promptly. Keep away from children. Contact your Intermec representative for replacement batteries.Several factors determine the life of your battery such as extreme tempera-tures, input devices, and your usage. For example, if you use a tethered scanner every day, you need to replace your battery more often than some-one who uses an internal scanner.The CK60 Computer contains an internal super capacitor, a temporary power storage device, that protects state for up to ten minutes. This is to give you time to replace the main battery pack before state is lost. Be sure to put the computer in a suspend mode before doing so.You can configure the battery power fail level so that after the system shuts down in a low battery condition, there is still sufficient charge to allow the unit to remain configured, keep proper time, and maintain DRAM (Dynamic Random Access Memory) for at least ten minutes at room tem-perature if the main battery remains in the handheld computer, using the Power control panel applet (see page 8). The state and time are lost if:• The battery discharges beyond this level.• The battery is removed when the computer is not in suspend mode.Changing and Installing the BatteryMake sure you fully charge the LiIon battery before you install it in your CK60 Computer; and that you take at least 20 minutes to initially charge the backup battery before the backup system is fully functional.The LiIon battery pack used in this device may present a fire or chemi-cal burn hazard if it is mistreated. Do not disassemble it, heat it above 100°C (212°F) or incinerate it.Avertissement: Le paquet de piles d’ions de lithium qui est utilisé dans cet appareil peut presenter un risque feu ou un risque chimique de brûlure s’il est maltraité. Il ne faut pas le désassembler, le réchauffer à une température plus élevée que 100°C (212°F) ou l’incinérer.If you fail to replace the battery immediately, you may lose important state or applications.Attention: Si la batterie n’est pas remplacée immédiatement, des don-nées ou applications importantes risquent d’être perdues.

Chapter 1 — Using the CK60 Handheld ComputerCK60 Handheld Computer with Windows CE User’s Manual 7To charge the batteryEither insert the battery into the CK60 Quad Battery Charger or place the CK60 Computer with battery installed in a CK60 Single Dock, a CK60 Single Dock with modem, or a CK60 Multidock. The battery charge time is four hours or less on any of these docks if the temperature is within the battery charging range.You could also use a CK60 Power Adapter to keep the CK60 Computer on full power.For maximum efficiency, store your CK60 Computer on external power with which to charge your batteries.For more information on these accessories, see “Accessories for the CK60 Computer” on page 17.To install the battery, insert the tabs on the bottom of the charged battery into the CK60 Computer and snap the battery into place.Maximizing Battery LifeBelow are things that you can do to maximize the life of your battery.Checking the Battery StatusThe battery status LED above your CK60 keypad, as shown in the follow-ing illustration, indicates the status of your battery. See the table on the next page to understand the meanings of the lights emitted from the LED.Maximizing the Life of Your BatteryWhen You Want To: Do This to Save Battery Power:Operate the CK60 Computer and the Low Battery status icon appears or the Battery light comes on.1Press I to turn off the CK60 Computer.2Remove the battery and insert another fully charged battery as quickly as possible or you may lose state.Or, you can insert the CK60 Computer into a powered quad battery pack charger.Stop using the CK60 Computer for five minutes or longer.1Make sure the low battery icon is not on the screen and that the Bat-tery light is not turned on.2Press I to turn off the CK60 Computer.Store the CK60 Computer for more than a day.1Save your state and end your computer session.2Press I to turn off the CK60 Computer.3Insert a fully charged battery.Battery status LED

Chapter 1 — Using the CK60 Handheld Computer8 CK60 Handheld Computer with Windows CE User’s ManualUsing the KeypadYour CK60 Computer has one of the following keypad overlay options:• 32-key DSD large numeric• 45-key full alphanumeric• 58-key full alphanumericSteady Green Battery is more than 95% charged and unit is on a charger.Blinking Red Battery is low.Steady Red Main battery is low, or if charging, remains red until your CK60 Computer reaches 95% charge status.Steady Yellow Your CK60 Computer is on a charging source and there is no battery pack installed. Can also mean that your CK60 Computer is out of charging range 32° to 122°F (0° to 50°C). Once your CK60 Computer gets back in range, charging resumes and the LED changes to red or green.Steady Amber Replace the battery pack.You can also use the Power control panel applet to view the status of this battery. Tap Start > Settings > Control Panel. Double-tap the Power icon, then tap the Power tab. Tap OK to exit this applet.

Chapter 1 — Using the CK60 Handheld ComputerCK60 Handheld Computer with Windows CE User’s Manual 932-Key Large Numeric KeypadThe 32-key keypad is for applications that enter mainly numeri data (0-9). This keypad also lets you enter special characters by pressing color-coded key sequences.45-Key Full Alphanumeric KeypadThis keypad is for applications that enter mainly numeric data (0-9) and that may need to enter the entire alphabet. This keypad also provides shirted function keys (F1-F12) and special characters, symbols, and func-tions by pressing color-coded key sequences.8579463210.-Esc EnterBacklight keyGreen keyOrange keyScan keyPower keyRollPageF1 F2 F3 F4F5 F6 F7 F8457896&*^EscSpace0123.,SpCAPSHelp Home NewLnOP QSPrintT?URWVFld EOFXZYDelReset+-Fld -=F1 F2 F3 F4F5 F6 F7 F8F11 F12F9F10APA1 PA2 PA3 AutLgAttnBC DEFClear DupFMark SysRqClr Fld XHexGH IJKLMNIns+ShiftCTRLEnterBacklight keyGreen keyOrange keyPower keyScan key

$Chapter 1 — Using the CK60 Handheld Computer10 CK60 Handheld Computer with Windows CE User’s Manual58-Key Full Alphanumeric KeypadThis keypad is for applications that enter mainly numeric data (0-9) and that may need to enter the entire alphabet. This keypad also provides shift function keys (F1-F24) and special characters, symbols, and functions by pressing color-coded key sequences.Using the Color-Coded KeysEach keypad available for the CK60 Computer provides color-coded keys to let you access additional characters, symbols, and functions printed on the keypad overlay. Once you understand how to use the color-coded keys and key sequences, you will know how to access all of the additional fea-tures printed on the keypad overlay. There are two color-coded modifier keys on the CK60 Computer: the orange B key and the green C key.You press and release the first key, then press and release the second key to access the color-coded character or function printed above a key. Note that there are several hidden characters (such as < or >) on each CK60 keypad that require using the color-coded keys to access them.Using the Color-Coded KeysYou Wan t To: Press: ExampleUse an orange character or func-tion printed above a key.B key, then the key with the charac-ter or function printed above it.Press B, then F7 to type the M char-acter on the 45-key keypad.Use a green character or function printed above a key.C key, then the key with the charac-ter or function printed above it.Press C, then Y to print the greater than symbol (>) on the 58-key key-pad..Lock the orange, green, Ctl, Alt, or Shift key to stay on.B, C, Ctl, A.t, or Shift key twice. Press C twice and the applicable icon appears in the status bar with a pad-lock.Unlock a green, orange, Ctl, Alt, or Shift key.B, C, Ctl, Alt, or Shift key once.Enter1203456789&*^CBADEFGJIHKLMNQPORXSTZUWVYEscSpaceShiftCTRLSymIns HomeHelpFld - EOFFld +AutoLgMenu+-=[]_'"~|.AttnHexPrint Reset SReqFMarkNewLnClr Clear Dup Erase Fld XCAPSPA1 PA2 PA3{`};:<>/\F9 F10 F11 F12 F13 F14F15 F16 F17 F18 F19 F20 F21F22 F23 F24DelRollPageF1 F2 F3 F4F5 F6 F7 F8Backlight keyGreen keyOrange keyScan keyPower key$

Chapter 1 — Using the CK60 Handheld ComputerCK60 Handheld Computer with Windows CE User’s Manual 11Capitalizing All CharactersTo type all alphanumeric characters as uppercase letters, you can enable the Caps Lock feature on the CK60 keypad.To enable Caps Lock, press the applicable sequence:• On the 45-key keypad, press the C key, then the Esc key.• On the 58-key keypad, press the B key, then the Space key.To disable Caps Lock, press the same key sequence you used to enable it.Typing Alphabetical Characters on the 45-Key KeypadOn the 45-key keypad, press the orange B key, then the applicable key to enter letters of the alphabet when necessary.Using the Power (I) KeyWhen you press the I key to turn off the CK60 Computer, you actually put the CK60 Computer in Suspend mode. In Suspend mode, the CK60 Computer continues to supply power to all memory, but turns off power to most hardware. This power-saving feature is to prolong battery life.When you press the I key to turn the CK60 Computer back on, your com-puter resumes where it was when you turned it off.If you are using WPA or 802.1x security, the computer may need to reau-thenticate before it starts your application.If the Battery light flashes and the CK60 does not resume after pressing I, your battery may be too low to supply power. Replace the battery.Turning on the Keypad BacklightYou can configure your keypad to turn on a backlight to assist you when you are working in low lighting. To adjust the backlight for the keypad, tap Start > Settings > Control Panel, then double-tap the Backlight icon. Tap the right arrow to move to and tap the Keyboard tab. Make your selection, then tap OK to exit this applet.

Chapter 1 — Using the CK60 Handheld Computer12 CK60 Handheld Computer with Windows CE User’s ManualUsing the ScreenThe CK60 Computer has a 3.8” diagonal, 240x320 pixel (QVGA) trans-flective TFT-LCD 64K color display. The screens support Unicode charac-ters, user-programmable fonts, and bitmap graphics. The Start screen has two distinct areas: the desktop and the taskbar. The desktop displays short-cuts to some of the applications installed on the CK60 Computer. The taskbar displays the Start menu, the time, the onscreen keyboard icon, and the desktop icon.Your CK60 Computer has a stylus for selecting items and entering infor-mation. Use the stylus in place of a mouse.Tap Touch the screen once with the stylus to select options, close appli-cations, or launch menus from the taskbar.Double-tap Touch the screen twice with the stylus to launch applications.Drag Hold the stylus on the screen and drag across the screen to select text and images.Tap a nd h old Tap and hold the stylus on an icon to see a list of actions available for the item. On the pop-up menu that appears, tap the action you want to perform.DesktopTaskbar

Chapter 1 — Using the CK60 Handheld ComputerCK60 Handheld Computer with Windows CE User’s Manual 13Using the SpeakersThe high-volume speaker on the back of the CK60 Computer, is capable of variable volume levels. This speaker is capable of reproducing voice and WAV files, and is used primarily to convey status tones. There is a separate volume control in the Volume & Sounds control panel applet. Information on this applet is below and on the next page.The front speaker is a full-voice range speaker of cell-phone quality with a separate volume control. See the next page for information about this vol-ume control.Enabling the Speaker and Adjusting the Volume2Drag the slider bar to the right to the “Soft” position.Warning: Do not place the speaker next to your ear when the speaker volume is set to “Loud” (maximum), or you may damage your hearing.To enable the speaker and adjust the volume:1Tap Start > Settings > Control Panel. Double-tap the Volume & Sounds icon, then tap the Volume tab.High-volume speaker on center, back of CK60 ComputerFront Speaker

Chapter 1 — Using the CK60 Handheld Computer14 CK60 Handheld Computer with Windows CE User’s Manual3Tap OK to exit this applet.Disabling the Speaker2Tap the Soft button to drag the slider all the way to the left.3Tap OK to exit this applet.Using the Status LightsThe status lights on the CK60 Computer turn on to indicate the status of the battery or a successful decode of a bar code.The battery lights and the battery screen icon work with each other to alert you to the status of your battery. If the battery light (to the right of the Scan button) comes on, check the status bar to see which battery icon appears on it. The battery may be critically low and need replacing.The Good Read light (green) above the display indicates when the CK60 Computer successfully decodes a bar code.To disable the speaker:1Tap Start > Settings > Control Panel. Double-tap the Volume & Sounds icon, then tap the Volume tab.

Chapter 1 — Using the CK60 Handheld ComputerCK60 Handheld Computer with Windows CE User’s Manual 15Using the Secure Digital CardYou can use a Secure Digital (SD) card to increase file storage and install software. The CK60 Computer currently supports SanDisk SD cards only. The SD card slot is located on the top of the CK60 Computer just above the scanner window.To insert an SD card:1Press I to turn off the CK60 Computer.2Remove the two screws on the SD card slot door and remove the door (see illustration on the next page). Note that the screws to this door are to be torqued to 1.5 in-lbs. 3Gently insert the SD card into the CK60 Computer with the printed side facing the keypad and screen side of the CK60 Computer.4Push the card into the slot until it latches in place and the steel card retainer covers the end of the SD card.5To replace the door, insert the door catch into the slot above the steel card retainer.6Replace the two screws.7Press I to turn on the CK60 Computer.To remove the SD card:1Press I to turn off the CK60 Computer.2Remove the two screws on the SD card slot door and remove the door. Note that the screws to this door are to be torqued to 1.5 in-lbs. Note: MultiMediaCards (MMCs) and CompactFlash (CF) storage cards are not supported in the CK60 Computer.Warning: You can corrupt your SD card if you do not follow these installation and removal procedures exactly.Screw Screw

Chapter 1 — Using the CK60 Handheld Computer16 CK60 Handheld Computer with Windows CE User’s Manual3Push in on the SD card until you hear it unlatch. The card should eject far enough that you can easily remove it from the CK60 Computer.If the card does not eject easily, you can use the door catch to remove it by turn the door upside down and using the catch to pull out the SD card.4Remove the SD card from the CK60 Computer.Physical and Environmental SpecificationsUse this section to locate technical information about the CK60 Computer and its available features and options.Physical DimensionsLength: 22.5 cm (8.87 in)Width: 9.3 cm (3.68 in)Depth: 5.0 cm (1.98 in) with standard caseWeight: 563 g to 852 g depending on configuration(23 oz to 30 oz)Power SpecificationsOperating: Rechargeable 17.6 W LiIon battery packBackup: Super Capacity supplies 10 minutes bridge time while replacing the main batteryElectrical SpecificationsModel: CK60External Charge Power: 11 to 28 VDC @ 1.5 A max. (18 W max.)Temperature and Humidity SpecificationsOperating temperature: -20° to 50°C (-4° to 122°F)Operating humidity: 95% noncondensingStorage temperature: -20° to 50°C (-4° to 122°F)Storage humidity: 95% relative humidity, noncondensingScreen Specifications• 240x320 pixels• 9.7 cm (3.8 in) diagonal active area• 5-level LED backlight control with high and low settingsWarning: Before installing an SD card, inspect the gasket on the door for any damage or wear, and replace the door if any damage or wear is found.

Chapter 1 — Using the CK60 Handheld ComputerCK60 Handheld Computer with Windows CE User’s Manual 17Keypad Options32-key DSD large numeric keypad45-key large alphanumeric keypad58-key alphanumeric keypadBar Code SymbologiesCodabar, Codablock A, Codablock F, Code 11, Code 2 of 5, Code 39, Code 93, Code 128, Interleaved 2 of 5, Matrix 2 of 5, Micro PDF417, MSI, PDF417, Plessey, RSS 14, RSS Expanded, RSS Limited, Telepen, UPC/EANAccessories for the CK60 ComputerYou can use these accessories (sold and ordered separately) with the CK60 Computer. To order accessories, contact your local Intermec representative.CK60 Quad Battery ChargerUse the Quad Battery Charger to charge up to four batteries without hav-ing to remove them from the CK60 Computer. You can insert up to four CK60 Computers with batteries installed making it easy to remember to charge your batteries overnight. The charger also provides power to your CK60 Computers while communicating via Ethernet.CK60 Ethernet MultidockUse the CK60 Ethernet Multidock to hold up to four CK60 Computers with a batteries installed. The multidock charges the batteries, provides power to the CK60 Computers, provides one Ethernet connector, and pro-vides a serial port for each inserted CK60 Computer.CK60 Single DockUse the CK60 Single Dock to hold a CK60 Computer with its battery installed. The single dock charges the battery, provides power to the CK60 Computer, provides an Ethernet connector, and provides a serial port for the inserted CK60 Computer.CK60 Single Dock with ModemUse the CK60 Single Dock with Modem to hold a CK60 Computer with its battery installed. The single dock charges the battery, provides power to the CK60 Computer, provides an Ethernet connector, and provides a serial port for the inserted CK60 Computer.CK60 Holster and BeltUse the holster and belt to carry your CK60 Computer while not using it. The holster and belt support either right- or left-handed use and you can use it to carry a CK60 Computer with or without a handle. You can only use this with a CK60 Computer that has either the 1D linear imager or the 2D imager.

Chapter 1 — Using the CK60 Handheld Computer18 CK60 Handheld Computer with Windows CE User’s ManualCK60 HandstrapThe removable and adjustable handstrap make it easy for you to hold and use the CK60 Computer without tiring your hand.CK60 Power Adapter, USB Adapter, and Snap-On AdaptersProvides power to all of the docks and chargers.

CK60 Handheld Computer with Windows CE User’s Manual 192Windows CEThis chapter introduces Microsoftr Windowsr CE 5.0. While using your CK60 Handheld Computer, keep this key point in mind:Tap Start on the task bar, located at the bottom, left corner of the screen, to quickly move to programs, files, and settings. Use the task bar at the bot-tom of the screen to perform tasks in programs. The task bar includes menus, buttons, and the onscreen keyboard.This chapter describes your CK60 Computer Windows CE applications, and explains how to connect your CK60 Computer to a PC, a network, or the Internet. Below is a guide to assist you in using your CK60 Computer.Note: Desktop icons and control panel applet icons are shown to the left. Any place that Start is mentioned, tap the following Windows icon in the bottom, left corner of your CK60 desktop. For information on: See this source:Programs on your handheld computer. This chapter.Connecting to and synchronizing with a PC. The Quick Start Guide or ActiveSync Help on your PC.Last-minute updates, detailed technical information. Read Me files in the Microsoft ActiveSync folder on the PC.Up-to-date information on Windows CE device. www.microsoft.com/windows/embedded/ce.net/default.asp

Chapter 2 — Windows CE20 CK60 Handheld Computer with Windows CE User’s ManualBasic SkillsLearning to use your CK60 Computer is easy. This section describes the basic concepts of using and customizing your CK60 Computer.Desktop ScreenWhen you turn on your CK60 Computer for the first time each day, you see the Desktop screen.Status icons display information such as low batteries or when the CK60 Computer is connected to a PC or to the Internet. You can tap an icon to open the associated setting or program.ProgramsYou can switch from one program to another by selecting it from the Start menu. To access some programs, tap Start > Programs, and then the pro-gram name.To customize what is displayed on the Desktop screen, including the back-ground image, tap Start > Settings > Control Panel, then double-tap the Display icon.Tap to list open windowsTap to activate the input panelDouble-tap to change time formatTap to scroll to other programsTap to open an associated programTap to bring up the Start menu

Chapter 2 — Windows CECK60 Handheld Computer with Windows CE User’s Manual 21Start Menu and Task BarThe Start Menu is located at the bottom of the screen. It displays the active program, and allows you to switch to programs and close screens.The task bar, which displays the current time, is at the bottom of the screen. The task bar includes menu names, buttons, and the Input Panel icon. Use this task bar to perform tasks in programs.NotificationsYour device can notify you in any of the following notification types:• A message box appears on the screen.• A sound, which you can specify, is played.• A light flashes on your CK60 Computer.Entering InformationYou can enter information on your CK60 Computer in several ways, depending on the type of device you have and the program you are using:Use the input panel to enter information in any program on your CK60 Computer. You can either type using the onscreen keyboard or write using Tr a n s c r i b e r (described on page 22). The characters appear as typed text.To show the input panel, tap the Input Panel icon, then tap Keyboard. To hide the input panel, tap the Keyboard icon, then tap Hide Input Panel.Typing Using the input panel, enter typed text into the CK60 Computer. You can do this by tapping keys on the onscreen keyboard or by using handwriting recognition software.Writing Using the stylus, write directly on the screen.Drawing Using the stylus, draw directly on the screen.Tap to see more programsTap to see websitesTap to see text files and other documentsTap to configure your unitTap to display the input panelTap to learn more about an applicationInput Panel iconSelect an input method

Chapter 2 — Windows CE22 CK60 Handheld Computer with Windows CE User’s ManualLarge Keys Versus Small Keys on KeyboardTyping With the Onscreen KeyboardTap the stylus input icon, then tap Keyboard. On the soft keyboard that is displayed, tap the keys with your stylus.• To type lowercase letters, tap the keys with the stylus.• To type a single uppercase letter or symbol, tap the Shift key. To tap multiple uppercase letters or symbols, tap the CAP key. Note that the CAP key only appears when the keyboard is set to small keys. See previous page for information about the keys.• To convert a letter to uppercase, tap and hold the stylus on the letter and drag up.• To add a space, drag the stylus to the right across at least two keys.• To backspace, drag the stylus to the left across at least two keys.• To insert a carriage return, tap and hold the stylus on the keyboard and drag down.Using TranscriberWith Transcriber, you can write on the screen with the stylus just as you would on paper. You can write a sentence or more of information, then pause and let Transcriber change written characters to typed characters.The default setting for the keyboard is with small keys. If you want to use larger keys, tap Start > Settings > Control Panel, then double-tap the Input Panel icon. Tap Options, then select Large keys. Tap OK, then OK again to close the Input Panel properties. Below are the keyboards.Keyboard with small keys Keyboard with large keys

Chapter 2 — Windows CECK60 Handheld Computer with Windows CE User’s Manual 23To enable the Transcriber, tap the Input Panel icon on the task bar, select Tr a n s c r i b e r, tap OK to close the Transcriber Intro, select an option, then write anywhere on the screen for the input to appear in the active window. Tap the Tr a n s c ri b e r icon, then select Hide Input Panel, to disable.Selecting Typed TextIf you want to edit or format typed text, you must select it first by dragging the stylus across the text.You can cut, copy, and paste text by tapping and holding the selected words and then tapping an editing command on the pop-up menu, or by tapping the command on the Edit menu.Finding and Organizing InformationYou can use the Windows Explorer to find files on your CK60 Computer and to organize these files into folders. Tap Start > Programs > Windows Explorer.For specific instructions on using Transcriber, double-tap the Tr a n s c r i b e r shortcut on the desktop screen or tap the Tr a n s c r i b e r option in the Input Panel menu, then tap Help. Tap OK to close the Transcriber Intro box.Transcriber iconDouble-tap a folder to open it.

Chapter 2 — Windows CE24 CK60 Handheld Computer with Windows CE User’s ManualCustomizing Your CK60 ComputerYou can customize your CK60 Computer by adjusting settings and install-ing additional software.Programs added to your CK60 Computer at the factory are stored in ROM (Read Only Memory). You cannot remove this software, and you cannot accidentally lose ROM contents.You can install any program created for your CK60 Computer, as long as your CK60 Computer has enough memory. The most popular place to find software for your CK60 Computer is on the Windows CE web site.Adding Programs Using Microsoft ActiveSyncInstall software developed for the CK60 Computer onto your PC before installing the same software onto your CK60 Computer. Once installation is complete, tap Start > Programs, then the program icon to switch to it.2Download the program to your PC (or insert the CD or disk that con-tains the program into your PC). You may see a single *.EXE or *.ZIP file, a SETUP.EXE file, or several files for different CK60 Computer types and processors. Be sure to select the program designed for the Win-dows CE and your CK60 Computer processor type.3Read any installation instructions, Read Me files, or documentation that comes with the program. Many programs provide instructions.4Connect the CK60 Computer and PC, then double-click the *.EXE file.• If the file is an installer, the installation wizard begins. Follow the directions on the screen. Once the software is installed, the installer automatically transfers the software to your CK60 Computer.• If the file is not an installer, an error message stating that the program is valid but it is designed for a different type of computer is displayed. 1Determine your CK60 Computer and processor type so that you know which version of the software to install. Tap Start > Settings > Control Panel, then double-tap the System icon. Note the processor information on the General tab beneath the Computer heading.

$Chapter 2 — Windows CECK60 Handheld Computer with Windows CE User’s Manual 25Move this file to your CK60 Computer. If you cannot find any instal-lation instructions for the program in the Read Me file or documenta-tion, use Microsoft ActiveSync Explore to copy the program file to the “My Computer\Program Files” folder on your CK60 Computer.Adding a Program Directly from the InternetInstall the appropriate software for your CK60 Computer on your PC before installing it on your CK60 Computer. Once installation is complete, tap Start > Programs, then the program icon to switch to it.2Download the program to your CK60 Computer straight from the Internet using Internet Explorer. You may see a single *.EXE or *.ZIP file, a SETUP.EXE file, or several versions of files for different CK60 Computer types and processors. Be sure to select the program designed for the Windows CE and your CK60 Computer processor type.3Read any installation instructions, Read Me files, or documentation that comes with the program. Many programs provide instructions.4Tap the file, such as *.EXE file to start the installation wizard. Follow the directions on the screen.Adding a Program to the Start MenuYou can either use Windows Explorer on the CK60 Computer to move the program to the “\My Computer\Windows\Start Menu” folder, or use Microsoft ActiveSync on the PC to create a shortcut to the program and place the shortcut in the “\My Computer\Windows\Start Menu” folder.1Determine your CK60 Computer and processor type so that you know which version of the software to install. Tap Start > Settings > Control Panel, then double-tap the System icon. Note the processor information on the General tab beneath the Computer heading.$

$Chapter 2 — Windows CE26 CK60 Handheld Computer with Windows CE User’s ManualUsing Windows Explorer on the CK60 ComputerTap Start > Programs > Windows Explorer, and locate the program. Tap and hold the program and tap Cut on the pop-up menu. Open the “\My Computer\Windows\Start Menu” folder, tap and hold a blank area of the window, and tap Paste on the pop-up menu. The program now appears on the Start menu. For more information on using Windows Explorer, see “Finding and Organizing Information” on page 23.Using Microsoft ActiveSync on the PCUse the Explore in Microsoft ActiveSync to explore your CK60 Computer files and locate the program. Right-click the program, and then click Cre-ate Shortcut. Move the shortcut to the “\My Computer\Windows\Start Menu” folder. The shortcut now appears on the Start menu. For more information, see ActiveSync Help.Removing ProgramsMicrosoft ActiveSyncVisit the following Microsoft web site for the latest in updates, technical information, and samples:http://msdn.microsoft.com/embedded/downloads/ce/default.aspxWith Microsoft ActiveSync, you can back up and restore your CK60 Com-puter data, and copy files between your CK60 Computer and your PC. Install Microsoft ActiveSync on the desktop of your PC from the following URL. For more information, on installing Microsoft ActiveSync, see your Quick Start card. ActiveSync is already installed on your CK60 Computer.http://msdn.microsoft.com/downloads/Tap Start > Settings > Control Panel, then double-tap the Remove Pro-grams icon.If the program does not appear in the list of installed programs, use Win-dows Explorer on your CK60 Computer to locate the program, tap and hold the program, and then tap Delete on the pop-up menu.Tap Start > Settings > Control Panel, then double-tap the PC Connection icon. Tap Change Connection, then select the baud rate from the list.$

Chapter 2 — Windows CECK60 Handheld Computer with Windows CE User’s Manual 27After installation is complete, the ActiveSync Setup Wizard helps you con-nect your CK60 Computer to your PC or set up a partnership so you can browse for or move data between your CK60 Computer and your PC.Disconnect the CK60 Computer from your PC and you are ready to go!IConnectNote that once you exit the IConnect application, select Start > Run, enter “IConnect.exe” in the Open field, then tap OK. The IConnect icon then reap-pears in the system tray.Note: While ActiveSync does synchronize files between your PC and your CK60 Computer, the Windows CE operating system does not include Cal-endar, Contacts, Tasks, Inbox, Channels, and Pocket Access applications.The IConnect application displays information about the Ethernet adapter and tests for connectivity. To access this application, tap the IConnect icon in your system tray. Two options will appear in a pop-up menu, to either open and or exit the application.

Chapter 2 — Windows CE28 CK60 Handheld Computer with Windows CE User’s ManualInternet ConnectionTap Open IConnect to access the IConnect application.Ethernet ConnectionsThe following information applies to CK60 Computers using Ethernet:IP AddressThe IP Address row is for the current IP address. If the address is valid, a green check mark appears to the left and the field contains the address. If invalid, a red X is shown to the left. Tap IP Address to configure the IP set-tings for the CK60 Computer and view other IP-related addresses.The DHCP dialog contains information about the current IP address. You can enter an IP address, check either Static IP or DHCP, then tap Update to commit these changes. Tap Release or Renew near the bottom to either release or renew changes to the DHCP address.LAN InfoTap LAN Info to access diagnostic pages.LinkThis row displays the current link speed if valid. A green check mark appears to the left if the Ethernet cable is attached to the CK60 Computer. A red X appears if the Ethernet cable is detached.Tap this to test the connection

Chapter 2 — Windows CECK60 Handheld Computer with Windows CE User’s Manual 29AdapterThis row lists the current network adapter. To change to a different adapter, tap the drop-down arrow, select a different adapter, then check Adapter Enabled below the drop-down list. To unload the current adapter, clear (uncheck) Adapter Enabled.For 802.11b/g ConnectionsThe following information applies to CK60 Computers using 802.11 Wireless:IP AddressThe IP Address row is for the current IP address. If the address is valid, a green check mark appears to the left and the field contains the address. If invalid, a red X is shown to the left. Tap IP Address to configure the IP set-tings for the CK60 Computer and view other IP-related addresses.The DHCP dialog contains information about the current IP address. You can enter an IP address, check either Static IP or DHCP, then tap Update to commit these changes. Tap Release or Renew near the bottom to either release or renew changes to the DHCP address.WLAN InfoTap WLAN Info to access diagnostic pages.SetupTap Setup to configure the 802.11b/g SSID and security settings. See “Configuring Security” on page 64 for more information.AdapterThis row lists the current network adapter. To change to a different adapter, tap the drop-down arrow, select a different adapter, then check Adapter Enabled below the drop-down list. To unload the current adapter, clear (uncheck) Adapter Enabled.

Chapter 2 — Windows CE30 CK60 Handheld Computer with Windows CE User’s ManualiFTP ServerTap the iFTP Server tab to set up the FTP Server on the CK60 Computer. Check or uncheck either option, tap Apply to change FTP Server settings.Getting ConnectedYou can set up connections to the Internet and corporate network at work to do such activities as browsing the Internet, sending and receiving e-mail and instant messages, and synchronizing information using Microsoft ActiveSync.Connections can be made using a wired or wireless network. Once con-nected to the Internet or to the network at your company or organization where you work, you can view web pages by using Internet Explorer. The communication software for creating an ISP connection is already installed on your CK60 Computer. Your service provider may provide the software needed to install other services, such as paging and fax services.Connecting to an Internet Service ProviderYou can connect to your ISP and use the connection to view web pages. Get the following information from your ISP. Some ISPs require informa-tion in front of the user name, such as “MSN/username.”• ISP dial-up access telephone number•User name•PasswordTo view additional information for any screen in the wizard or while changing settings, tap Help in the upper-right corner.

Chapter 2 — Windows CECK60 Handheld Computer with Windows CE User’s Manual 311Tap Start > Settings > Network and Dial-up Connections, then double-tap Make New Connection.2Enter a name for the connection, such as “My Connection,” then press Next.3In the Select a modem list, select “Hayes Compatible on COM1.” Tap Next to continue.

Chapter 2 — Windows CE32 CK60 Handheld Computer with Windows CE User’s Manual4Enter the phone number, then tap Finish.6Tap Dial Properties, then specify your current location from the drop-down list.Specify your current phone type. If your phone type is pulse dialing, select Pulse dialing. If your type is tone dialing (as most phone lines are), then select Tone dialing. Tap OK to close the Dialing Properties page. These settings apply to all connections.7To start the connection, start visiting web sites by using Internet Explorer. See “Internet Explorer” on page 34 for information.Direct ConnectionA direct connection helps you to securely connect to servers, such as a cor-porate network, via the Internet. Ask your network administrator for the user name, password, domain name, TCP/IP settings, and host name or IP address of the server.5Double-tap the new ISP Connection icon, then enter the user name, password, and domain (if provided by an ISP or your network adminis-trator).To view additional information for any screen in the wizard or while changing settings, tap Help in the upper-right corner.

Chapter 2 — Windows CECK60 Handheld Computer with Windows CE User’s Manual 331Tap Start > Settings > Network and Dial-up Connections, then double-tap Make New Connection.2Enter a name for the connection, such as “Direct Connection.” Select Direct Connection, then tap Next to continue.3Select a device through which a connection is made from the Select a device drop-down list, tap Configure to adjust the port settings, tap OK to return to the Device screen, then tap Finish.4Insert the necessary equipment into the device, then double-tap the new Direct Connection icon to connect to the host.5Use a desired program to automatically begin connecting. For example, switch to Internet Explorer and browse to a web page.

Chapter 2 — Windows CE34 CK60 Handheld Computer with Windows CE User’s ManualEnding a ConnectionTo disconnect, either detach your device when connected via cable or cra-dle, or switch off the connection when connected via a wireless network.Internet ExplorerUse Microsoft Internet Explorer to view web sites. To do this, create the connection first via an ISP or network, as described in “Getting Con-nected” on page 30.When connected to an ISP or network, you can also download files and programs from the InternetViewing Mobile Favorites and Channels1Tap Favorites from the tool menu to display your list of favorites.2Tap the page you want to view.Browsing the Internet1Set up a connection to your ISP or corporate network using information as described in “Getting Connected” on page 30.2To connect and start browsing, do one of the following:•Tap Favorites from the toolbar, and then tap the favorite to view.To switch to Internet Explorer on your CK60 Computer, double-tap the Internet Explorer icon on your desktop.Tap to add or delete a folder or a linkTap the favorite you want to view

Chapter 2 — Windows CECK60 Handheld Computer with Windows CE User’s Manual 35•In the Address bar that appears at the top of the screen, enter the web address you want to visit using the input panel, then tap the [Enter] key on the panel to go to that web site.• Tap the drop-down arrow to select from previously entered addresses.Note: To add a favorite link while using the CK60 Computer, go to the page you want to add, then select Favorites > Add to Favorites.Type the web address hereTap for a list of addresses

Chapter 2 — Windows CE36 CK60 Handheld Computer with Windows CE User’s Manual

CK60 Series Handheld Computer User’s Manual 373Configuring the CK60 ComputerUse this chapter to understand how to install applications onto your CK60 Series Handheld Computer and how to configure the CK60 Computer to communicate in your network. In this chapter are these sections:• Developing Applications for the CK60 Computer (page 38)• Packaging Applications for the CK60 Computer (page 39)• Installing Applications on the CK60 Computer (page 40)• Converting Older Computer Applications to CK60 Applications (page 38)• Configuring CK60 Parameters (page 49)• Configuring the CK60 Computer for Your Network (page 53)• Configuring the SF51 Scanner (page 61)• Configuring Security (page 64)• Using Configuration Parameters (page 90)• Using Reader Commands (page 91) Note: Desktop icons and control panel applet icons are shown to the left. Any place that Start is mentioned, tap the following Windows icon in the bottom, left corner of your CK60 desktop.

Chapter 3 — Configuring the CK60 Computer38 CK60 Series Handheld Computer User’s ManualDeveloping Applications for the CK60 ComputerCK60 Computers run applications programmed in Microsoft Embedded Visual C++. Use this section to understand what you need to:• Develop a new application for the CK60 Computer.• Convert an application from an older computer to a CK60 application.Use the Intermec SDK to develop new applications to run on the CK60 Computer. The Intermec SDK is a library of C++ language functions you can use to create applications for the CK60 Computer.See the SDK online user’s manual for help developing your application. The Intermec CK60 SDK User’s Manual contains hardware and software requirements, all of the functions that are supported by the CK60 Com-puter, and how to use these functions.The SDK is part of the Intermec Developer’s Library (IDL), which is avail-able on the Intermec Developer’s Library CD or as a download from the Intermec web site at www.intermec.com.You need these hardware and software components to use the Intermec SDK:• Pentium PC, 400 MHz or higher• Windows 2000 (Service Pack 2 or later) or Windows XP (Home, Profes-sional, or Server)• For native C++ development, Microsoft eMbedded Visual C++ version 4.0•For Windows CD 5.0, eVC 4.0 SP4 is required • 128 MB RAM (196 MB recommended)• 360 MB hard drive space for minimum installation (720 MB for com-plete)• CD-ROM drive compatible with multimedia PC specification• VGA or higher-resolution monitor (Super VGA recommended)• Microsoft Mouse or compatible pointing deviceConverting Older Computer Applications to CK60 ApplicationsIf you have an existing application that you would like to run on the CK60 Computer, you can use the PSK to convert that application. The Intermec PSK is a set of libraries and tools that you use to convert your existing C applications into C++ applications for use on the CK60 Computer.As you migrate from another computer to a CK60 Computer, you need to consider when converting other computer applications to run on the CK60 Computer, most APIs should work without changes, with the exception that arrow and tab keys may be reversed from other computers. Keyboard

$Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 39remapping is available on the CK60 Computer should you need to map these keys like that of the other computer.You need these hardware and software components to use the PSK:• a PC with at least 1MB of free disk space running Microsoft Windows 2000 or Windows XP• Microsoft eMbedded Visual C++ version 4.0 with Service Pack 2• Intermec SDK and development tools• Intermec PSK, which contains these files and utilities:• PSK functions library• Header files• Example filesThe PSK is part of the Intermec Developer’s Library (IDL), which is avail-able on the Intermec Developer’s Library CD or as a download from the Intermec web site at www.intermec.com.Packaging Applications for the CK60 ComputerUse any of these methods to package applications for installation:• You could package an application as a cabinet (CAB) file. Recommended• For simple applications, the application itself may be the file to deliver.• It could be a directory structure that contains the application, supporting files like ActiveX controls, DLLs, images, sound files, and data files.Consider any of the following when choosing a location into which to store your application:• In the basic CK60 Computer, there are two built-in storage options: the Object Store and the Flash File Store. The Object Store is a Disk on Chip (DOC) Flash that looks like a disk. The Flash File Store is an area of storage which is embedded in a section of the system’s FLASH mem-ory. This storage area is not erased during a cold-boot. It may, however, be erased during the reflashing process. In addition to storing applica-tions and data files, you do have the option to store a persistent registry to the Flash File Store region.• If the optional Secure Digital (SD) storage card is in the system, then consider this card the primary location to place applications installation files. The “\Storage Card” folder represents the SD card.• Use the small non-volatile Flash File Store region to hold CAB files that rebuild the system at cold-boot or install applications from a CAB file into the Flash File Store so they are “ready-to-run” when a cold-boot is performed. Since the FLASH in the system has a limited number of write cycles, do not use the Flash File Store for excessive writing pur-poses; however, reading is okay.$

$Chapter 3 — Configuring the CK60 Computer40 CK60 Series Handheld Computer User’s ManualCAB files (short form of “cabinet” files) are compressed folders as defined by Microsoft. A “cabinet” file is a single file, usually suffixed with .CAB, that stores compressed files in a file library. A compressed file can be spread over several cabinet files. During installation, the setup application decompresses the files stored in a cabinet and copies them to the user’s system. Intermec recommends using CAB files to install your applications. The CK60 Com-puter uses standard Windows CE CAB files and does install third-party CAB files.For the CK60 Computer, CAB files register DLLs, create shortcuts, modify registry entries, and run custom setup programs. Tap a CAB file to extract that file or place the CAB file on one of the approved storage devices in the “\CabFiles” folder, then perform a warm-boot on the CK60 Computer. There are two methods available to extract a CAB file:• Tap a CAB file to extract it. With this method, the CAB file is automat-ically deleted when the extraction process is successful, unless the CAB file is set with the read-only attribute.• Use the AUTOCAB method to extract all files when a cold-boot is per-formed on the CK60 Computer. This method is on the Intermec Devel-oper’s Library CD, see its Software Tools User’s Manual for information.Installing Applications on the CK60 ComputerYou can use either the Microsoft ActiveSync application or SD storage cards to install applications on the CK60 Computer.Installing Applications Using Microsoft ActiveSyncYou can use Microsoft ActiveSync to establish a connection between your PC and the CK60 Computer. Microsoft ActiveSync transfers files, synchro-nizes files, performs remote debugging, and other device management activities.See Chapter 2, “Windows CE” for information about the Microsoft Active-Sync application as provided by Microsoft Corporation.This can be a serial, a USB, or an 802.11b/g Microsoft ActiveSync connec-tion. Files can be copied using Windows Explorer on a PC or a laptop com-puter. This is usually good when updating a few CK60 Computers.These instructions assume that Microsoft ActiveSync was installed onto your PC and is up and running. If not, go to Chapter 2, “Windows CE” for an URL from which to download the latest application.1Connect the CK60 Computer to a PC using a USB or serial cable. You may have to detach, then reattach the cable to “wake” the connection.2Wait for a “Connected” message to appear in the Microsoft ActiveSync application to signal a connection to the CK60 Computer. If necessary, select File > Get Connected to initiate a connection or detach, then reat-tach the USB or serial cable.$

$Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 415Within the “Mobile Device” folder, go to the folder where you want the files located on the CK60 Computer, do a right-click for a pop-up menu, then select Paste.6When all of the files are pasted, perform a warm-boot on the CK60 Computer. When the computer reboots, wait for the LED on the top left of your keypad to stop blinking. Tap Start > Programs > Windows Explorer to locate the newly copied executable files, then tap these files to activate their utilities.Installing Applications Using a Secure Digital CardIf you have an SD card for your CK60 Computer, this is the best place for you to install applications.1If you are using an SD card reader, suspend the CK60 Computer, remove its SD card, and place it in the reader. For help, see “Using the Secure Digital Card” on page 15.2Copy your application file to the SD card. If you are using Microsoft ActiveSync to copy the files to the SD card, place the application in the “\Storage Card” folder on the CK60 Computer.3If using an SD card reader, insert the SD card back into the CK60.4Navigate to the “\Storage Card” folder and run your application. After your application is installed, you can run it from the Programs menu.3Click Explore to access the “Mobile Device” folder on your unit.4From your PC, select Start > Windows Explorer, then browse the “C:\Intermec\CK60 Mgmt Tools\CabFiles” path for any CAB files needed for your CK60 Computer. Select the appropriate file, right-click the file for a pop-up menu, then select Copy.$

$Chapter 3 — Configuring the CK60 Computer42 CK60 Series Handheld Computer User’s ManualLaunching Your Application AutomaticallyYou can configure the various media used in the Windows CE system with a folder name and can change the media in the registry of the system. Many of the startup components rely on folder names to locate information files, applications, or other related data.The registry keys used by FolderCopy and other startup components to retrieve the folder names are as follows:Flash File Store[HKLM\Drivers\BuiltIn\FlshDrv]"FolderName"="Flash File Store"SD Card (Storage Card)[HKLM\System\StorageManager\Profiles\SDMemory]"Folder"="Storage Card"Disk On Chip[HKLM\System\StorageManager\Profiles\TRUEFFS_DOC]"Folder"="DiskOnChip"During normal Windows CE system startup, there are Intermec-specific and non-Intermec components that require an orderly start to properly function. These non-Intermec components may also need to start them-selves so the Windows CE device can function properly. Since there are possible configurations that come from using one or more optional built-in peripheral devices, the platform components starting on the next page are required to manage startup.PreShellPreShell (PRESHELL.EXE) is launched prior to the Microsoft Shell and must execute a SignalStartup call before the Microsoft Shell launches.PreShell searches the “\Flash File Store\2577” directory for an executable of the same name. If one exists, that application is launched. This application can do what a customer desires prior to launching the Microsoft Shell. This feature allows end customers to make their own application the shell of the system. If desired, do not exit the custom shell nor call SignalStarted.PostShellPostShell (POSTSHELL.EXE) can launch an application after the Microsoft Shell has launched. There are utility applications that exist that can take advantage of “hooking” the startup for maintenance, for example.Note: This describes the system component startup for Intermec provided components only. It does not describe the bootstrap loader process. It only describes the component installation process provided by Windows CE. It is assumed that you understand the Microsoft CE startup procedures and are familiar with how Microsoft components start up.$

$Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 43PostShell searches the “\Flash File Store\2577” directory for an executable of the same name. If one exists, that application is launched instead. This application can do what a customer desires and is launched after the Microsoft Shell starts initialization. The Microsoft Shell does not require complete initialization before this application begins and that may cause some application or system issues. These issues are expected and are consid-ered normal for those developing PostShell applications. The application must test if the APIs it requires are available.RunAutoRunSystem components are installed and configured during the power up process from a single starting point. RunAutoRun (RUNAUTORUN.EXE), built into the operating system image and located in the “\Windows\Startup” folder, checks for AutoExec (AUTOEXEC.EXE) in a “\2577” folder on a mounted volume in this order:• Secure Digital (SD)• Object Store - may be non-volatile storage or RAM• Disk on Chip - may map as Object Store• Flash File Store - may map as Object Store. This is the default location for the AutoExec program in Intermec systems. Intermec system applica-tions are started from this folder. The ordering of mounted volumes overrides this feature.The folder names used for the mounted volumes above are retrieved from the registry to maintain coherence with the naming of the mounted vol-umes on the platform. These folder names are not hard-coded. If AutoExec is present in the “\2577” folder on any of these media, it executes the pro-gram only on the first media it is found on and no other.AutoExec is reserved for Intermec use to configure Intermec-specific appli-cations. It launches the CAB installer, AutoCab (AUTOCAB.EXE), to install platform cab files to the system, such as Intermec Data Collection.When the AUTOEXEC.EXE process completes, Run Autorun then checks for the existence of AutoRun (AUTORUN.EXE) and executes this pro-gram from the first media it is found on. This order is the same as what is used by AutoExec.$

Chapter 3 — Configuring the CK60 Computer44 CK60 Series Handheld Computer User’s ManualAutoRun is reserved for customer use to configure application launch sequences. It launches the CAB installer, AutoCab, as well as any customer programs that added to the AUTOUSER.DAT file and is described on the next page. The hierarchy of these files is shown below.AutoExecAutoExec (AUTOEXEC.EXE) automates operations such as pausing, launching processes, or signaling, and is configured through the AutoExec data file (AUTOEXEC.DAT). This script file must be in the same direc-tory as the program itself. Usage: AutoExec [-%[W]] [-E=["X"]] [-F=["Y"]] [-LOG=] [-W=[Z]]The return code from the process uses the standard error codes defined in WINERROR.H. Note: Intermec considers the usage of the AutoExec data file as “Intermec Private.” AutoExec installs Intermec applications such as Data Collection, Security Supplicants, Intermec Management, control panels, and shortcuts from components found in the Flash File System. Do not modify the AutoExec data file. Instead, use the AutoRun program to add software com-ponents.-% Passes an ID to use in a call to SignalStarted. This argument is useful only during system startup that relies on a SignalStarted to call. W is an integer value.-E Passes a signal event name to use when autoexec completes. X is a string value.-F Overrides the data file to use. This must be a fully qualified name. Default is “autoexec.dat” in the same loca-tion as the AUTOEXEC.EXE program. Y is a string value.-LOG Set to any value logs activity to AUTOEXEC.TXT (in the same location as the AUTOEXEC.EXE pro-gram). Default is disabled.-W Pauses the autoexec process by calling sleep for the number of seconds specified by Z. Z is an integer value.runautorun autoexec autorun autocopy autoreg foldercopy customer applications autocab autocab

$Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 45Keywords that AutoExec supports are:Examples of keyword usage are as follows:; Allow message pop up if an error occurs.QUIET 0; Log any debug output to a trace file.LOGGING 1; Perform a SetEvent on the event name "autoexec_started".SIGNAL "autoexec_started"; Include this child data file, childexec.dat.CALL "\childexec.dat"; Use autocopy to copy the audio control panel from flash file store to the windows directory. Wait for up to 60 seconds for it to exit.EXEC "\Flash File Store\2577\autocopy.exe" -S"\Flash File Store\System\CPLAu-dio.cpl" -D"\Windows\CPLAudio.cpl"; Change the default EXEC wait time to 90 seconds.EXECWAIT 90; Suspend processing any commands for 10 seconds.WAIT 10; Suspend processing any commands until event called MyEventName is signaled.WAITFOR "MyEventName"QUIET Enables user notification when an error occurs.LOGGING Enables logging to a trace file.SIGNAL Enables the specified named event and is immediately signaled. Useful for notifying other compo-nents of the current status.CALL Opens another .DAT file to process. After the called file is completed, this file is resumed.RUN Runs a program with a SW_SHOWNORMAL attribute. Autoexec does not wait for the child process to exit.LOAD Runs a program with a SW_HIDE attribute. Autoexec waits for 60 seconds for the child process to exit or EXECWAIT seconds if set.EXEC Runs the specified program. AutoExec waits 60 seconds for the child process to exit or EXECWAIT seconds if set.EXECWAIT Changes the default EXEC wait time from 60 seconds to the number of seconds specified. There is a maximum 10-minute limit imposed.WAIT Forces a sleep for the specified number of seconds to occur.WAITFOR Forces a sleep until the named event is signaled.$

$Chapter 3 — Configuring the CK60 Computer46 CK60 Series Handheld Computer User’s ManualAutoRunAutoRun (AUTORUN.EXE) automates operations such as launching other processes and is configured through the AutoRun data file (AUTORUN.DAT). This script file must be in the same directory as the program itself.AutoRun supports the following script commands in AUTOUSER.DAT and AUTORUN.DAT.AutoRun handles quoted file names for the first parameter which allows you to specify path names or file names that contain white space. Note that only one set of quotes per command is supported.AUTORUN.DAT entry examples:AutoCopyAutoCopy (AUTOCOPY.EXE) copies or moves files from one location to another. It has no user interface and is configured through command line arguments. It has support for the following parameters, in no particular order:Usage: AutoCopy [-D["W"]] [-L["X"]] [-M[D]] [-Q[Y]] [-S["Z"]] Note: If you need to add steps at boot time, add them to AUTOUSER.DAT, not to AUTORUN.DAT. AUTORUN.DAT is pro-vided by Intermec and is subject to change. AUTOUSER.DAT is the desig-nated place for the end user to add steps to the boot time process.EXEC Launches a specified program, waits for it to complete (up to 10 minutes).CALL Processes a specified file of commands and returns.CHAIN Processes a specified file of commands and does not return.RUN Loads a specified program and executes it.LOAD Loads a specified program and executes it.RUN “Flash File Store\Apps\some.exe” arg1, arg2, arg3CALL “Flash File Store\2577\usercmds.dat”-D Indicates the destination file name and must be fully qualified. W is a string value.-L Indicates a fully qualified file name for logging to enable. Default is disabled. X is a string value.-M Moves file to a destination rather than copies the file. Default value is disabled. D is an integer value. D=1 indicates enabled, 0 is disabled.-Q Indicates if a message box should appear when an error occurs. Default is disabled. Y is an integer value.-S Indicates a source file name and must be fully qualified. Z is a string value.$

$Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 47The return code from the process uses the standard error codes defined in WINERROR.H.Example:; use AutoCopy to copy the control panel from flash file store to windows. autocopy.exe -S"\Flash File Store\System\Audio.cpl" -D"\Windows\Audio.cpl"; use AutoCopy to move the control panel from flash file store to windows. autocopy.exe -M1 -S"\Flash File Store\System\Audio.cpl" -D"\Windows\Audio.cpl"AutoRegThe AutoReg (AUTOREG.EXE) component adds registry information to the Windows CE registry. It has no user interface and is configured through command line arguments. Usage: AutoReg [-D] [-HKey] [-Q] “filename”The return code from the process uses the standard error codes defined in WINERROR.H.Example:; use AutoReg to install this registry information.autoreg.exe "\Flash File Store\install.reg"; use AutoReg to install this registry information. Delete the file afterwards.autoreg.exe -D "\Flash File Store\install.reg"; use AutoReg to extract registry information to a file. autoreg.exe -HHKEY_LOCAL_MACHINE\Software\Intermec\Version "\version.reg"The format of the input file, in this example, is the standard registry format which should ease the creation of the input file since there are many pub-licly available utilities to generate a registry file besides Notepad. One example of a tool is the Microsoft Remote Registry Editor.AutoCabAutoCab (AUTOCAB.EXE) extracts files, registry settings, and shortcuts from Windows CE cabinet (.CAB) files. The Windows CE startup sequence invokes AutoCab as a part of AutoExec and AutoRun. During the Windows CE startup sequence, AutoCab processes all CAB files in the “\CabFiles” directory relative to the current location of Autocab, unless the location is overridden by command line arguments. AutoCab can run as a stand-alone program to install a CAB file or a directory of CAB files.-D Deletes the registry file after successfully loading it. This allows for systems that have hives implemented.-H Saves the registry path, and all child entries, to the specific .REG registry file.-Q Indicates whether a message box should appear when a fatal error occurs.filename Fully qualified file name to read from or write to, encased in double quotes to support spaces in paths or file names. See examples below.$

$Chapter 3 — Configuring the CK60 Computer48 CK60 Series Handheld Computer User’s ManualAutoCab only installs the CAB file if it was not installed before by Auto-Cab. To track the installation of a CAB file, AutoCab marks the CAB file with the System attribute. This attribute is ignored if the device is perform-ing a cold-boot on a non-persistent file system.AutoCab preserves the CAB file after installation if the ReadOnly attribute is set. If not set, the CAB file is deleted automatically after installation.Usage:AutoCab [-ChkRst=][-File=][-Force][-Log=][-Move=][-Quiet=][-Show=][-Signal=]Command line switches are described below.If <PathName> references a single CAB file, that file is processed. If <Path-Name> references a directory, all the .CAB files in that directory is pro-cessed. If <PathName> is a wild card pattern, all files matching that pattern is processed, If <PathName> is omitted, InstallCab processes all the .CAB files in directory “\CabFiles.”Example:; Install all cab files in the \Flash File Store\XYZ directory, regardless.AutoCab -FILE="\Flash File Store\XYZ\*.cab" -FORCE; Install only one cab file, use Intermec cab installation displayAutoCab -FILE=”\myCab\app.cab” =show=2Customizing How Applications Load on the CK60 ComputerIf you have several processes that you need running in a specific order as the CK60 Computer turns on, you can use the AutoRun system to customize the way applications load. For compatibility with other Intermec comput-ers, you can place a copy of AUTORUN.EXE in the same folder as your AUTORUN.DAT file but it is not required.-ChkRst= Set to 1 to configure AutoCab to check for the Reset flag after all CAB files are installed. This file is cre-ated by CAB files that want a warm reset after installation. Default is 0 (do not check for flag).-File= Specifies the CAB files to extract. Note that the specified files need not end with the .CAB extension.-Force Forces the specified CAB files to extract regardless of whether it was previously extracted.-Log= Set to 1 to create a log file in the same folder that AutoCab is running. Useful for debugging CAB installation. Default is 0 (disabled).-Move= Set to 1 to force source CAB file deletion, even when read-only bit set on file. Default is 0 (disabled).-Quiet= Set to 0 to allow AutoCab to display user message box on errors. Useful for debugging CAB installation. Default is 1 (keep quiet).-Show= Set to 0 to prevent showing any installation progress interfaces. Also prevents user from canceling instal-lation. Set to 1 to show normal installation. Set to 2 to show Intermec installation progress interface (user can see what is installing but cannot cancel it). Default is 1 (show normal).-Signal= Set to string name of signal to use at the completion of CAB installation before a reboot occurs (if enabled). AutoCab uses WaitForSingleObject on this name. Default is disabled.$

$Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 49To create and install the AUTORUN.DAT file on your CK60 Computer1On the CK60 Computer, create a folder called “2577.”2On your desktop, open the Notepad application.3Write commands for AUTORUN.DAT using these supported script commands:4Save this Notepad file as AUTORUN.DAT.5Copy the AUTORUN.DAT file to the “\2577” folder on your CK60 Computer.During every boot, the system scans for AUTORUN.DAT in the “\2577” folder.Here is a sample AUTORUN.DAT file that runs a dialer application and connects to a VPN:EXEC “\Program Files\My Dialer\Dialer.exe” 348-2600EXEC “\Program Files\My VPN\Connect.exe” MyDomainConfiguring CK60 ParametersYou can configure many parameters on the CK60 Computer, such as the bar code symbologies it decodes or the network settings. These characteris-tics are controlled by configuration parameters. The values you set for these configuration parameters determine how the computer operates. Use con-figuration commands to configure the CK60 Computer.Configuring with the Setup AssistantWhen first setting up the CK60 Computer, use the Setup Assistant to set or enable basic network parameters and connect your CK60 Computer to the network. Script Command DescriptionEXEC Launches a specified program and waits up to 10 minutes for it to complete.CALL Processes a specified file of commands, returns. When you use the CALL command, the execution of the current file pauses while a new file that follows the same set of commands executes. Once the new file completes executing, AutoRun.exe continues processing the current file.CHAIN Processes a specified file of commands and does not return. This command calls another file that follows the same set of commands and stops processing the current file.RUN Loads a specified program and executes it. Specifies the show window attribute so that the user interface is visible when the application launches.LOAD Loads a specified program and executes it. Specifies the hide window attribute so the user interface is hidden initially.$

Chapter 3 — Configuring the CK60 Computer50 CK60 Series Handheld Computer User’s ManualThe Setup Assistant guides you through setting the following basic network parameters:• Date and time (including time zone)•SSID (Network name)• DHCP server or IP address, subnet mask, and default router• Primary and secondary DNS or WINS addresses•Device nameTo set other parameters, use the Intermec Settings control panel applet or another configuration method. The Setup Assistant runs on the CK60 Computer the first time you turn on the computer.After the Setup Assistant is complete, the CK60 Computer should commu-nicate with the network. A network connection icon appears in the taskbar.Synchronizing the CK60 Computer System Time with a Time ServerIt is important that the time on all of your CK60 Computers be synchro-nized with a network time server to ensure real-time communications and updates. Network time servers acquire Coordinated Universal Time (UTC) from an outside source such as the U.S. Naval Observatory (USNO). The CK60 Computer uses Simple Network Time Protocol (SNTP) to synchro-nize with a network time server.The default reference time server is the USNO (tock.usno.navy.mil). To synchronize the time on your CK60 with this time server, you must have a valid connection to the Internet. You can also synchronize the CK60 Com-puter system time with a corporate network server within your firewall that is SNTP-capable. To use an internal corporate network server, you need to set the command name in the registry.Configuring the CK60 Computer through the NetworkYou can change the configuration parameters of the CK60 Computer by sending commands through a host computer or through the network. If you are using a network, you can configure one or more CK60 Computers at a time. You can remotely configure the wireless or Ethernet CK60 Com-puter by sending a command from an application on the host computer. Note that you cannot set all parameters through the network. You can only set those commands that have a syntax in the Command Reference Manual.Configuring the CK60 Computer in a TCP/IP Direct Connect NetworkYou can use the host computer to configure a wireless or Ethernet CK60 Computer in your TCP/IP network. To send and receive configuration data, you need to write a host application that can communicate with the Note: You can continue running an application on the CK60 Computer while configuring it from the host computer.

Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 51CK60 Computer directly through an access point or through the Ethernet network. Use the TMF protocol to send and receive transactions between the host application and the CK60 Computer.To set up the host computer, verify that you can communicate with the CK60 Computer.To set up the application, prepare and write a host application that can communicate with the Intermec Application Server and send transactions to and receive transactions from the CK60 Computer in this format:where:ExampleIn the host application, you want to get the current values of two configura-tion commands from the CK60 Computer. Send the CG$+NABV transaction from the host applicationwhere:The CK60 returns the CgS+BV4 transaction to the host application, where:TMF field commandsTMF field is a 2-byte field containing one of these values:CG Configuration Get request sent from the host application.Cg Configuration Get response sent from the CK60 Computer to the host computer.CS Configuration Set request sent from the host application.Cs Configuration Set response sent from the CK60 Computer to the host computer.commands are the reader and configuration commands that you want to set on the CK60 Computer or the current value you want to retrieve from the CK60 Computer. To save configuration changes in flash memory, send the reader command .+1 as the last command. for a list of all commands, see the Command Reference Manual.Note: The transaction header is not shown in this example. You do not need a transaction header for a host application in a TCP/IP network, but you do for a UDP Plus network.CG is a TMF Configuration Get request.$+ is the Change Configuration reader command.BV is the Beeper Volume configuration command.Cg is a TMF Configuration Get response.$+ is the Change Configuration reader command.BV4 means the Beeper Volume configuration command is currently set to a value of 4, which is a very high beeper volume.

Chapter 3 — Configuring the CK60 Computer52 CK60 Series Handheld Computer User’s ManualConfiguring the CK60 Computer in a UDP Plus NetworkYou can use the host computer to configure a CK60 Computer in your wireless or Ethernet network. To send and receive configuration data or files, you need to write a host application that can communicate with an Intermec Application Server (formerly Gateway or DCS 30X).For help, see the appropriate Gateway or DCS 30X User’s Manual. Use the Terminal Message Format (TMF) protocol to send and receive transactions between the host application and the CK60 Computer.To set up the Intermec Application Server, configure a peer-to-peer desti-nation name for the host application. Create a transaction ID, $NGCF-GRSP, that routes to this destination name. The Intermec Application Server uses the transaction ID to route responses from the CK60 Computer back to the host application. $NGCFGRSP is a special transaction ID that the server uses to forward configuration response data from a CK60.All configuration responses are routed with the $NGCFGRSP transaction ID. The Intermec Application Server cannot track multiple applications sending reader or configuration commands. If you have two host applica-tions sending reader or configuration commands, they must both be con-figured to receive the $NGCFGRSP transactions, and therefore both receive all responses from all CK60 Computers.To set up the host computer, verify that the host computer can communi-cate with the Intermec Application Server.To set up the application, prepare and write a host application that can communicate with the Intermec Application Server and send transactions to and receive transactions from the CK60 Computer in this format. For an example of the host application transaction, see page 51.where:transaction header TMF field commandstransaction headeris a 96-byte field with message number, date, time, source application ID, destinations application ID, transaction ID, and other information. Set the system message (SYS$MSG) flag to E in the transaction header.TMF field is a 2-byte field containing one of these values:CG Configuration Get request sent from the host application.Cg Configuration Get response sent from the CK60 Computer to the host computer.CS Configuration Set request sent from the host application.Cs Configuration Set response sent from CK60 to host computercommands are the reader and configuration commands that you want to set on the CK60 Computer or the current value you want to retrieve from the CK60 Computer. To save configuration changes in flash memory, send the reader command .+1 as the last command. See the Command Reference Manual for a list of supported commands.

Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 53Configuring the CK60 Computer for Your NetworkThe CK60 Computer is a versatile handheld computer that you can add to your wired or wireless data collection network. You can connect your CK60 Computer to your network using:• Serial communications• 802.11b/g radio communications• Ethernet communications• Bluetootht radio communicationsConfiguring Serial CommunicationsThe CK60 Computer has a serial port to transfer data to and receive data from another device via RS-232 communications. You can also insert the CK60 Computer into a communications dock to transmit data to and receive data from a host computer or PC using RS-232 communications. The serial cable and the communications dock are sold separately. For more information on accessories, see page 17.To use serial communications with your CK60 Computer, connect the CK60 Computer to the serial port of another device, by:• connecting the CK60 Serial Port to the serial port of the other device using the 26-pin to DB9-pin serial cable adapter and a female-to-female null modem RS-232 cable;• connecting the CK60 Dock to the serial port of the other device using a DB9-pin to DB9-pin serial adapter cable, then insert the CK60 Com-puter into the dock; or• connecting a USB cable between the USB connector in the back of the CK60 Dock and your desktop computer.Configuring 802.11b/g Radio CommunicationsThe wireless CK60 Computer has an internal 802.11b/g radio to transfer data using wireless communications. This section of the manual assumes that you have already set up your wireless communications network includ-ing your access points. If you are using a UDP Plus network, you also need to have your Intermec Application Server communicating with a host com-puter. Make sure all components with antennas are at least 30 cm (1 ft) aport when power is applied. Failure to comply could result in equipment damage.Attention: Assurez-vous que la distance entre tous les éléments avec antennes soit d’au moins 30 centimètres (un pied) avant de faire la con-nexion avec l’alimentation électrique, faute de quoi vous risquez d’endommager votre installation.

Chapter 3 — Configuring the CK60 Computer54 CK60 Series Handheld Computer User’s ManualYour CK60 Computer supports these network protocols:•TCP/IP•UDP PlusThe next sections explain the parameters you need to configure for the CK60 Computer to work in your wireless network.Configuring the Network Parameters for a TCP/IP NetworkIn a TCP/IP network, the CK60 Computer communicates with a host computer directly using TCP/IP. The access point acts as a bridge to allow communications between the wired network and the wireless network.To use wireless communications in a TCP/IP network, configure the Net-work Name (SSID), Host IP Address, IP Settings (if not using DHCP), and Network Port parameters on each CK60 Computer in the network.Configuring the Network Parameters for a UDP Plus NetworkIn a UDP Plus network, the CK60 Computer communications with a host computer through the Intermec Application Server.The Intermec Application Server translates UDP Plus packets on the wire-less network into TCP/IP packets on the wired network and vice versa. The access point acts as a bridge to allow communications between the wired network and the wireless network.To use wireless communications in a UDP Plus network, configure the Network Name (SSID), Controller IP Address, IP Settings (if not using DHCP), and Network Port parameters on each CK60 in the network.Configuring Ethernet CommunicationsYou can use the CK60 Computer directly in an Ethernet network if you have ordered the Ethernet option on your CK60 Computer and you insert it into a CK60 Dock. The communications dock as an Ethernet connector that makes it possible for the CK60 Computer to communicate with your Ethernet network.To use the CK60 Computer in an Ethernet network, configure the Net-work Name (SSID), Host IP Address, IP Settings (if not using DHCP), and Network Port parameters on each CK60 Computer in the network. If required for your network, set the Primary and Secondary DNS Server and Primary and Secondary WINS Server parameters on each CK60 Computer in the network.Configuring Bluetooth Radio Communications“Bluetooth” is the name given to a technology standard using short-range radio links, intended to replace the cables connecting portable and fixed electronic devices. The standard defines a uniform structure for a wide range of devices to communicate with each other, with minimal user effort.

Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 55Its key features are robustness, low complexity, low power, and low cost. The technology offers wireless access to LANs, the mobile phone network, and the internet for a host of home appliances and portable hand-held devices located up to 100m (328ft) apart (in a line of sight environment).Local BluetoothThe Local Bluetooth control panel applet displays the device name, the device address, enables or disables Bluetooth communications, and sets dis-coverable and connectable settings. This also provides a versions screen for various Bluetooth items in the system.Use this applet to enable Bluetooth communications before you configure radio communications.Wireless PrintingThe Wireless Printing control panel applet separates the task of wireless printing from other Bluetooth management items not relevant to this task.Wireless Printing has a concept of the “current wireless printer.” This printer is the one to which the CK60 Computer makes a connection when the wireless printing COM port is opened. If there is no current wireless printer, there is no wireless printing COM port. Registration and deregis-tration of this COM port is controlled by BTCC. Use the Wireless Printing control panel applet to handle the COM port registration. Customer soft-1Select Start > Settings > Control Panel, then double-tap the Local Blue-tooth icon.2Tap the top button to On, then tap OK to close the applet.Device Name Provides the “friendly” name of your CK60 Computer.Device Address Universally unique and cannot be changed - read-only.Discoverable Check this to ensure your CK60 is discoverable to other Bluetooth devices. The default is for the CK60 Computer to be undiscoverable as it does not offer any incoming services out of the box.Connectable Check this to allow other Bluetooth devices to connect to your CK60 Computer. The default is for the CK60 Computer to be unconnectable as it does not offer any incoming services out of the box.Class of Device This sets how a CK60 appears to other devices during a device discovery. The default is “0x920100” which specifies that the CK60 is capable of services of information, object transfer, and networking.Tap this to “On”

Chapter 3 — Configuring the CK60 Computer56 CK60 Series Handheld Computer User’s Manualware or other test applications can also use this applet to manage the COM port registration and deregistration.The current wireless printer is stored in the registry and is registered and deregistered on Bluetooth stack load/unload. If the current wireless printer changes, the existing wireless printing COM port is deregistered, and the new one is registered instead. The registered COM port is stored in the reg-istry as the “WPort.”For more information on using Bluetooth communications, see the Wireless Printing Development Guide available on the Intermec Developer’s Library CD or the Intermec web site at www.intermec.com.Use any of the following methods to set the wireless printer:• Use a Bluetooth device discovery to locate the remote device (page 56)• Manually enter the remote Bluetooth Device Address (page 57)• Use the Bluetooth Device Manager to choose from previously discovered printers (page 58)To do a Bluetooth device discovery:You can set your wireless printer via a Bluetooth Device Discovery, which takes about half a minute to locate all Bluetooth devices in your range.3Momentarily, Bluetooth devices discovered within range appear. If your preferred printer is in the list, select to highlight the printer, then tap OK. If you do not see your preferred device, make sure this device is powered on and set to discovery, then tap Device Discovery again. 1Select Start > Settings > Control Panel, then double-tap the Wireless Printing icon.2Select Device Discovery, then tap Acquire Printer to initiate the device discovery.

Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 57Click Cancel to return to the first screen without making changes.To enter the remote device address, if you know the Bluetooth Device Address of the printer you want to use, you do the following to avoid Device Discovery and perform a manual setup.3Type the address of your device in the field, then click OK. Tap Cancel to return to the first screen without making changes.When you set your printer manually, your device does not receive the printer name. Therefore, “-unknown-” is displayed under Device Name unless you enter the correct value in to the registry in some other way.1Select Start > Settings > Control Panel, then double-tap the Wireless Printing icon.2Select Manual, then tap Acquire Printer to go to the Manual Set dialog.

Chapter 3 — Configuring the CK60 Computer58 CK60 Series Handheld Computer User’s ManualTo choose from previously discovered printers, do the following to select from a list of previously discovered printers:3Select to highlight the printer of choice, then tap OK. Tap Cancel to return to the first screen without making changes.Bluetooth DUNDo the following to enable Bluetooth DUN on the CK60 Computer:1Select Start > Settings > Control Panel, then double-tap the Wireless Printing icon.2Select Device Manager, then tap Acquire Printer to go to the list of pre-viously discovered printers.1Select Start > Settings > Control Panel, then double-tap the Network and Dial-up Connections icon.2Double-tap Make New Connection, type your connection name, check Dial-Up Connection, then tap Next to continue.

Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 593Select “Bluetooth” from the Select a modem drop-down list, then tap Bluetooth to access the Add Bluetooth Modem dialog.4Tap Discover to discover and link to a Bluetooth modem or to a Blue-tooth-enabled mobile phone.5When prompted, enter the passkey in the Authentication Request dia-log. The default passkey should be listed in the user manual for your periph-eral device.6Select your device from the list of discovered devices, then tap Bond.

Chapter 3 — Configuring the CK60 Computer60 CK60 Series Handheld Computer User’s ManualOn successful bonding, notification appears at the bottom of the dialog, such as in the following illustration.7Tap Exit to complete the discovery and bonding of your device, tap Next, enter the phone number for your connection, then tap Finish to close the dialog.8Double-tap your connection icon, enter your dial-up networking account information in the User Name and Password fields, then tap Connect to establish a connection.

Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 61Configuring the SF51 ScannerThe following information pertains to configuring the SF51 Scanner to work with you CK60 Computer. These instructions assume you have the EasySet application installed on your desktop or laptop. The EasySet appli-cation is available from the Intermec Data Capture web site, contact your Intermec representative for information about this application.Enabling BluetoothBluetooth is required for the SF51 Scanner. On the CK60 Computer, use the Local Bluetooth control panel applet to enable Bluetooth communica-tions before you configure the SF51 Scanner.3Tap OK to close the applet.1Select Start > Settings > Control Panel, then double-tap the Local Blue-tooth icon.2Tap the top button to On, check Connectable, then take note of the device address. You will need this address to create your SF51 Connec-tion Labels. Instructions start on the next page.Tap this to “On“Check to enable “Connectable”

Chapter 3 — Configuring the CK60 Computer62 CK60 Series Handheld Computer User’s ManualCreating an SF51 Connection LabelTo initiate a connection from the SF51 Scanner, use your EasySet applica-tion to create an SF51 connection label with the CK60 Bluetooth address. The device address is listed in the Local Bluetooth control panel applet on your CK60 Computer, like the illustration shown on the previous page.2In the left side of the EasySet application, double-click Data transmis-sion settings > Bluetooth parameters > connect/disconnect > compose BT address.3Enter the Bluetooth address assigned to your CK60 Computer (shown in your Local Bluetooth control panel applet), then click OK to close this dialog. 1On your desktop or laptop, double-click the EasySet icon to activate the EasySet application if you have not already done so.

Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 634The connection label for the SF51 Scanner appears to the right in the EasySet application, similar to the following. Scan the label once, then confirm the blue light on end of the SF51 Scanner starts blinking, which means it is trying to connect. When connected, the blue light assumes a steady blue, then SF51 data gets wedged through the keyboard interface.Viewing SF51 Scanner Information from Your CK60 ComputerNote that in the CK60 Computer, the Intermec Settings control panel applet can display up to seven separate SF51 connections. The following illustration shows two such connections under the Scanners, Symbologies option.In this applet, tap Scanners, Symbologies, then tap (+) to expand the SF51 Scanner connections to view MAC addresses, firmware version numbers, and whether each scanner is connected to the CK60 Computer. When you clear (uncheck) Enable scanner port, the SF51 Scanner is disconnected from the CK60 Computer. Check Enable scanner port again to reconnect.If you want to rename these connections to descriptions more suitable for your situation, press the stylus on each SF51 Scanner connection for a pop-up menu, then select Rename. Enter the new description, then tap ok to save your entry.When the SF51 Scanner is connected, configuration changes take effect immediately. When the SF51 Scanner is not connected, configuration changes take effect once the SF51 Scanner is reconnected.SF51 identified by device addressSF51 default name

Chapter 3 — Configuring the CK60 Computer64 CK60 Series Handheld Computer User’s ManualConfiguring SecurityUse the next sections to understand how to configure each type of security on your wireless CK60 Computer. If you choose not to use security, see “Using Configuration Parameters” on page 90 for help.If you are using 802.1x security, this sections also assumes that your authentication server and access points are properly configured.Loading CertificatesIf you choose to use Transport Layer Security (TLS) with WPA or 802.1x security, you need to have a unique client certificate on the CK60 Com-puter and a trusted root certificate authority (CA) certificate. If you choose to use PEAP, you need to load a root CA certificate. You can use a third-party CA to issue unique client certificates and a root certificate.Wireless NetworkYour wireless adapter (network interface card) connects to wireless net-works of two types: infrastructure networks and ad-hoc networks.• Infrastructure networks get you onto your corporate network and the internet. Your CK60 Computer establishes a wireless connection to an access point, which links you to the rest of the network. When you con-nect to a network via an access point, you are using the 802.11b/g infra-structure mode.• Ad-hoc networks are private networks shared between two or more cli-ents, even with no access point.Each wireless network is assigned a name (or Service Set Identifier - SSID) to allow multiple networks to exist in the same area without infringement.If your CA is on your WLAN, select Start > Settings > Control Panel, then double-tap the Certificates icon to access the Certificate control panel applet and obtain the certificates.Note: Do not perform a cold-boot on the CK60 Computer. This resets the time and date.

Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 65Intermec Technologies recommends using security measures with wireless networks to prevent unauthorized access to your network and to ensure your privacy of transmitted data. The following are required elements for secure networks:• Authentication by both the network and the user• Authentication is cryptographically protected• Transmitted dataThere are many schemes available for implementing these features.TerminologyBelow are terms you may encounter as you configure your wireless net-work:AES (Advanced Encryption Standard)A block cipher, a type of symmetric key cipher that uses groups of bits of a fixed length - called blocks. A symmetric key cipher is a cipher that uses the same key for both encryption and decryption.CKIP (Cisco Key Integrity Protocol)This is Cisco's version of the TKIP protocol, compatible with Cisco Airnet products.EAP (Extensible Authentication Protocol)802.11b/g uses this protocol to perform authentication. This is not necessarily an authentication mechanism, but is a common framework for transporting actual authentication protocols. Intermec provides a number of EAP protocols for you to choose the best for your network.TKIP (Temporal Key Integrity Protocol)This protocol is part of the IEEE 802.11i encryption standard for wireless LANs., which provides per-packet key mixing, a message integrity check and a re-keying mechanism, thus overcoming most of the weak points of WEP. This encryption is more difficult to crack than the standard WEP. Weak points of WEP include:• No Installation Vector (IV) reuse protection• Weak keys• No protection against message replay• No detection of message tampering• No key updatesWEP (Wired Equivalent Privacy) encryptionWith preconfigured WEP, both the client CK60 Computer and access point are assigned the same key, which can encrypt all data between the two devices. WEP keys also authenticate the CK60 Computer to the access point - unless the CK60 Computer can prove it knows the WEP key, it is not allowed onto the network.WEP keys are only needed if they are expected by your clients. There are two types available: 64-bit (5-character strings, 12345) (default) and 128-bit (13-character strings, 1234567890123). Enter these as either ASCII (12345) or Hex (0x3132333435).WPA (Wi-Fi Protected Access)This is an enhanced version of WEP that does not rely on a static, shared key. It encompasses a number of security enhancements over WEP, including improved data encryption via TKIP and 802.11b/g authentication with EAP.WiFi Alliance security standard is designed to work with existing 802.11 products and to offer forward compatibility with 802.11i.WPA2 (Wi-Fi Protected Access)Second generation of WPA security. Like WPA, WPA2 provides enterprise and home Wi-Fi users with a high level of assurance that their data remains protected and that only authorized users can access their wireless networks. WPA2 is based on the final IEEE 802.11i amendment to the 802.11 standard ratified in June 2004. WPA2 uses the Advanced Encryption Standard (AES) for data encryption and is eligible for FIPS (Federal Information Processing Standards) 140-2 compliance.

Chapter 3 — Configuring the CK60 Computer68 CK60 Series Handheld Computer User’s ManualNoneUse “None” to disable 802.11b/g Security and enable WEP encryption.To Disable 802.1x Security1Set 8021x Security as “None.”2Set Association to “Open.”3Set Encryption to “None.”To Enable WEP Encryption1Set 8021x Security as “None.”2Set Association to either “Open” if WEP keys are not required; or “Shared” when WEP keys are required for association.3Set Encryption to “WEP.” See page 65 for information about WEP encryption.4If you had set Association to “Shared,” then select a data transmission key from the Data TX Key drop-down list near the bottom of this screen, then enter the encryption key for that data transmission in the appropriate Key # field.

Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 69To Enable WPA Encryption Using a Preshared Key1Set 8021x Security as “None.”2Set Association to “WPA.” See page 65 for information about WPA encryption.3Skip Encryption as it is automatically set to “TKIP.” See page 65 for more information about TKIP.4Enter the temporal key as ASCII (12345) in the Pre-Shared Key field.

Chapter 3 — Configuring the CK60 Computer70 CK60 Series Handheld Computer User’s ManualPEAP (Protected EAP)This protocol is suitable for performing secure authentication against Win-dows domains and directory services. It is comparable to EAP-TTLS (see page 65), both in its method of operation and its security, though not as flexible. This does not support the range of inside-the-tunnel authentica-tion methods supported by EAP-TTLS. Microsoft and Cisco both support this protocol.Use “PEAP” to configure the use of PEAP as an authentication protocol and to select “Open,” “WPA,” “WPA2,” or “Network EAP” as an associa-tion mode.To Enable PEAP with an Open Association1Set 8021x Security as “PEAP.”2Set Association to “Open.”3Skip Encryption as it is automatically set to “WEP.” See page 65 for more information about WEP.4Enter your unique user name and password to use this protocol. Select Prompt for password to have the user enter this password each time to access the protocol; or leave Use following password as selected to auto-matically use the protocol without entering a password.5Tap Get Certificates to obtain or import server certificates. See page 84 for more information.6Tap Additional Settings to assign an inner PEAP authentication and set options for server certificate validation and trust. See page 74 for more information.

Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 71To Enable PEAP with WPA Encryption1Set 8021x Security as “PEAP.”2Set Association to “WPA.” See page 65 for information about WPA encryption.3Skip Encryption as it is automatically set to “TKIP.” See page 65 for more information about TKIP.4Enter your unique user name and password to use this protocol. Select Prompt for password to have the user enter this password each time to access the protocol; or leave Use following password as selected to auto-matically use the protocol without entering a password.5Tap Get Certificates to obtain or import server certificates. See page 84 for more information.6Tap Additional Settings to assign an inner PEAP authentication and set options for server certificate validation and trust. See page 74 for more information.

Chapter 3 — Configuring the CK60 Computer72 CK60 Series Handheld Computer User’s ManualTo Enable PEAP with WPA2 Encryption1Set 8021x Security as “PEAP.”2Set Association to “WPA2.” See page 65 for information about WPA2 encryption.3Select Encryption to either “TKIP” or “AES.” See page 65 for more information about TKIP and page 65 for more information about AES.4Enter your unique user name and password to use this protocol. Select Prompt for password to have the user enter this password each time to access the protocol; or leave Use following password as selected to auto-matically use the protocol without entering a password.5Tap Get Certificates to obtain or import server certificates. See page 84 for more information.6Tap Additional Settings to assign an inner PEAP authentication and set options for server certificate validation and trust. See page 74 for more information.

Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 73To Enable PEAP with Network EAP1Set 8021x Security as “PEAP.”2Set Association to “Network EAP.” See page 65 for information about EAP.3Select Encryption to either “WEP” or “CKIP.” See page 65 for more information about WEP and page 65 for more information about CKIP.4Enter your unique user name and password to use this protocol. Select Prompt for password to have the user enter this password each time to access the protocol; or leave Use following password as selected to auto-matically use the protocol without entering a password.5Tap Get Certificates to obtain or import server certificates. See page 84 for more information.6Tap Additional Settings to assign an inner PEAP authentication and set options for server certificate validation and trust. See page 74 for more information.

Chapter 3 — Configuring the CK60 Computer74 CK60 Series Handheld Computer User’s ManualAdditional PEAP Settings1Select an authentication method from the Inner PEAP Authentication drop-down list.2Check Validate Server Certificate to verify the identity of the authenti-cation server based on its certificate when using PEAP.3Enter the Common Names of trusted servers. Note that if these fields are left blank, the server certificate trust validation is not performed or required.4Click X to return to the Security page.EAP/MS-CHAP-V2 Authenticates against a Windows Domain Controller and other non-Windows user databases. This is Microsoft's implementation of PEAP.EAP/Token Card Use with token cards. The password value entered is never cached. This is Cisco's implementation of PEAP.EAP/MD5-Challenge Message Digest 5. A secure hashing authentication algorithm.

Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 75TLS (EAP-TLS)EAP-TLS is a protocol that is based on the TLS (Transport Layer Security) protocol widely used to secure web sites. This requires both the user and authentication server have certificates for mutual authentication. While cryptically strong, this requires corporations that deploy this to maintain a certificate infrastructure for all their users.Use “TLS” to configure the use of EAP-TLS as an authentication protocol, and select “Open,” “WPA,” “WPA2,” or “Network EAP” as an association mode.To Enable TLS with an Open Association1Set 8021x Security as “TLS.”2Set Association to “Open.”3Skip Encryption as it is automatically set to “WEP.” See page 65 for information about WEP encryption.4Enter your unique Subject Name and User Name to use this protocol.5Tap Get Certificates to obtain or import server certificates. See page 84 for more information.6Tap Additional Settings to set options for server certificate validation and trust. See page 78 for more information.

Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 79TTLS (EAP-Tunneled TLS)This protocol provides authentication like EAP-TLS (see page 75) but does not require certificates for every user. Instead, authentication servers are issued certificates. User authentication is done using a password or other credentials that are transported in a securely encrypted “tunnel” established using server certificates.EAP-TTLS works by creating a secure, encrypted tunnel through which you present your credentials to the authentication server. Thus, inside EAP-TTLS there is another inner authentication protocol that you must configure via Additional TTLS Settings.Use “TTLS” to configure the use of EAP-TTLS as an authentication proto-col, and select “Open,” “WPA,” “WPA2,” or “Network EAP” as an associa-tion mode.To Enable TTLS with an Open Association (default configuration)1Set 8021x Security as “TTLS.”2Set Association to “Open.”3Skip Encryption as it is automatically set to “WEP.” See page 65 for information about WEP encryption.4Enter your unique user name and password to use this protocol. Select Prompt for password to have the user enter this password each time to access the protocol, or leave Use following password as selected to auto-matically use the protocol without entering a password.5Tap Get Certificates to obtain or import server certificates. See page 84 for more information.6Tap Additional Settings to assign an inner TTLS authentication and an inner EAP, and set options for server certificate validation and trust. See page 83 for more information.

Chapter 3 — Configuring the CK60 Computer80 CK60 Series Handheld Computer User’s ManualTo Enable TTLS with WPA Encryption1Set 8021x Security as “TTLS.”2Set Association to “WPA.” See page 65 for information about WPA encryption.3Skip Encryption as it is automatically set to “TKIP.” See page 65 for more information about TKIP.4Enter your unique user name and password to use this protocol. Select Prompt for password to have the user enter this password each time to access the protocol, or leave Use following password as selected to auto-matically use the protocol without entering a password.5Tap Get Certificates to obtain or import server certificates. See page 84 for more information.6Tap Additional Settings to assign an inner TTLS authentication and an inner EAP, and set options for server certificate validation and trust. See page 83 for more information.

Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 81To Enable TTLS with WPA2 Encryption1Set 8021x Security as “TTLS.”2Set Association to “WPA2.” See page 65 for information about WPA2 encryption.3Select Encryption to either “TKIP” or “AES.” See page 65 for more information about TKIP and page 65 for more information about AES.4Enter your unique user name and password to use this protocol. Select Prompt for password to have the user enter this password each time to access the protocol, or leave Use following password as selected to auto-matically use the protocol without entering a password.5Tap Get Certificates to obtain or import server certificates. See page 84 for more information.6Tap Additional Settings to assign an inner TTLS authentication and an inner EAP, and set options for server certificate validation and trust. See page 83 for more information.

Chapter 3 — Configuring the CK60 Computer82 CK60 Series Handheld Computer User’s ManualTo Enable TTLS with Network EAP1Set 8021x Security as “TTLS.”2Set Association to “Network EAP.” See page 65 for information about EAP.3Select Encryption to either “WEP” or “CKIP.” See page 65 for more information about WEP and page 65 for more information about CKIP.4Enter your unique user name and password to use this protocol. Select Prompt for password to have the user enter this password each time to access the protocol, or leave Use following password as selected to auto-matically use the protocol without entering a password.5Tap Get Certificates to obtain or import server certificates. See page 84 for more information.6Tap Additional Settings to assign an inner TTLS authentication and an inner EAP, and set options for server certificate validation and trust. See page 83 for more information.

Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 83Additional TTLS Settings1Select an authentication method from the Inner TTLS Authentication drop-down list.2If you select “EAP” for the inner authentication protocol, then select an inner EAP protocol from the Inner EAP drop-down list.3Enter the Common Names of trusted servers. Note that if these fields are left blank, the server certificate trust validation is not performed or required.4Check Validate Server Certificate to verify the identity of the authenti-cation server based on its certificate when using TTLS.5Enter the Anonymous EAP-TTLS Name as assigned for public usage. Use of this outer identity protects your login name or identity.6Click X to return to the Security page.PAP Password Authentication Protocol. A simple authentication protocol that sends security information in the clear.CHAP Challenge Handshake Authentication Protocol. Use of Radius to authenticate a terminal without sending security data in the clear. Authenticates against non-Windows user databases. You cannot use this if authenticating against a Windows NT Domain or Active Directory.MS-CHAP; MS-CHAP-V2 Authenticates against a Windows Domain Controller and other non-Windows user databases.PAP/Token Card Use with token cards. The password value entered is never cached.EAP Extensible Authentication Protocol. See page 65 for information about EAP.

Chapter 3 — Configuring the CK60 Computer84 CK60 Series Handheld Computer User’s ManualTo Get CertificatesCertificates are pieces of cryptographic data that guarantee a public key is associated with a private key. They contain a public key and the entity name that owns the key. Each certificate is issued by a certificate authority.Use this page to import a certificate onto the CK60 Computer.Root Certificates1Tap the <<< button next to the Import Root Certificate field to select the root certificate (DER-encoded .CER file) to import.2Click Import Root Cert to install the selected certificate.User Certificate1Tap the <<< button next to the Certificate Path field to select the user certificate (DER-encoded .CER file without the private key) to import.2Tap the <<< button next to the Key Path field to select the private key (.PVK file) which corresponds to the user certificate chosen in step 1.3Tap Import User Cert to install the selected certificate.Web EnrollmentTap Web Enrollment to obtain a user certificate over the network from an IAS Server. Tap X to return to the Security page.

Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 85LEAP (Cisco Lightweight EAP)LEAP is the Cisco Lightweight version of EAP. See page 65 for information about EAP.Use “LEAP” to configure the use of LEAP as an authentication protocol, select “Open,” “WPA,” “WPA2,” or “Network EAP” as an association mode, or assign “Network EAP.” Note that this defaults to the Network EAP.To Enable LEAP with an Open Association1Set 8021x Security as “LEAP.”2Set Association to “Open.”3Skip Encryption as it is automatically set to “WEP.” See page 65 for more information about WEP.4Enter your unique User Name to use this protocol.5Select Prompt for password to have the user enter this password each time to access the protocol, or leave Use following password as selected to automatically use the protocol without entering a password.

Chapter 3 — Configuring the CK60 Computer86 CK60 Series Handheld Computer User’s ManualTo Enable LEAP with WPA Encryption1Set 8021x Security as “LEAP.”2Set Association to “WPA.” See page 65 for information about WPA encryption.3Skip Encryption as it is automatically set to “TKIP.” See page 65 for more information about TKIP.4Enter your unique User Name to use this protocol.5Select Prompt for password to have the user enter this password each time to access the protocol, or leave Use following password as selected to automatically use the protocol without entering a password.

Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 87To Enable LEAP with WPA2 Encryption1Set 8021x Security as “LEAP.”2Set Association to “WPA2.” See page 65 for information about WPA2 encryption.3Select Encryption to either “TKIP” or “AES.” See page 65 for more information about TKIP and page 65 for more information about AES.4Enter your unique User Name to use this protocol.5Select Prompt for password to have the user enter this password each time to access the protocol, or leave Use following password as selected to automatically use the protocol without entering a password.

Chapter 3 — Configuring the CK60 Computer90 CK60 Series Handheld Computer User’s ManualUsing Configuration ParametersA configuration parameter changes the way the CK60 Computer operates, such as configuring a parameter to have the CK60 Computer emit a very loud beep in a noisy environment. Use any of these methods to execute configuration parameters:Scan EasySet bar code labels:You can use the EasySet application from Intermec Technolo-gies Corporation to print configuration labels. Scan the labels to change the imager configuration and data transfer settings. For more information, see the EasySet online help.Send Reader Commands through the Network or from an ApplicationYou can configure parameters by sending the following reader commands through the network or from an application. See “Using Reader Commands” on page 91 for more information.Reader Command Description Options (Syntax Data for Reader Commands)Audio VolumeChanges the volume of all audio signals 0 - Off1 - Low2 - Medium (default)3 - High4 - Very highAutomatic ShutoffSets the length of time the CK60 Computer remains on when there is no activity. When you turn on the CK60 Computer, it either resumes exactly where it was when you turned in off or boots and restarts your application.1 - 1 minute2 - 2 minutes3 - 3 minutes (default)4 - 4 minutes5 - 5 minutesBacklight TimeoutSets the length of time that the display backlight remains on. If you set a longer timeout value, you use the battery power at a faster rate.0 - Disable10 - 10 seconds30 - 30 seconds60 - 1 minute (default)120 - 2 minutes180 - 3 minutes240 - 4 minutes300 - 5 minutesDate/Time Sets the current date and time. DateYear - 0000-9999 (1999)Month - 1-12 (6)Day - 1-31 (1)TimeHour - 0-23 (0)Minute - 0-59 (00)Second - 0-59 (00)

Chapter 3 — Configuring the CK60 ComputerCK60 Series Handheld Computer User’s Manual 91Using Reader CommandsAfter the CK60 Computer is connected to your network, you can send the CK60 Computer a reader command from an application to perform a task, such as changing the time and date. Some reader commands temporarily override the configuration settings and others change these settings.Change ConfigurationThe Change Configuration command must precede any configuration command. If you enter a valid string, the CK60 Computer configuration is modified and the computer emits a high beep. To send the Change Config-uration command through the network, use the $+ [command] syntax where command is the two-letter command syntax for the configuration command followed by the value to set for that command.You can also make changes to several different commands by using the $+ [command]...[command n] syntax. There are seven configuration com-mand settings that can be changed in this way. See each command for infor-mation on respective acceptable “data” values.Example 1To change the Beep Volume to Off, you can send this string to the CK60 Computer through the network:$+BV0where:$+Indicates Change Configuration.BVSpecifies the Audio Volume parameter.0Specifies a value of Off.Example 2To change the Beep Volume to Very Quiet and the Virtual Wedge Grid to 123:$+BV1AF123where:$+Indicates Change Configuration.BV1Specifies Audio Volume, set to Very Quiet (1)AF123Specifies Virtual Wedge Grid, set to a value of 123.Command SyntaxAudio Volume BVdataAutomatic Shutoff EZdataBacklight Timeout BFdataVirtual Wedge Grid AFdataPostamble AEdataPreamble ADdata

Chapter 3 — Configuring the CK60 Computer92 CK60 Series Handheld Computer User’s ManualSet Time and DateThis command sets the date and time on the CK60 Computer. The default date and time is June 1, 1999 at 12:00 AM.From the network, send the following:/+ yyyymmddhhmmsswhere acceptable values for the date are:yyyy0000-9999 Yearmm01-12 Month of the yeardd01-31 Day of the monthhh00-23 Hourmm00-59 Minutesss00-59 SecondsYou can also set the time and date by using the Date/Time control panel applet. Tap Start > Settings > Control Panel, then double-tap the Date/Time icon to configure the time and date.

CK60 Series Handheld Computer User’s Manual 934Maintaining the CK60 ComputerUse this chapter to upgrade the operating system, run diagnostics, solve problems you may encounter, and perform routine maintenance on your CK60 Handheld Computer:Note: Desktop icons and control panel applet icons are shown to the left. Any place that Start is mentioned, tap the following Windows icon in the bottom, left corner of your CK60 desktop.

Chapter 4 — Maintaining the CK60 Computer94 CK60 Series Handheld Computer User’s ManualUpgrading the Operating System on your CK60 ComputerYou can use the Intermec Recovery Tools CD to reinstall or upgrade the oper-ating system software on the CK60 Computer. For more information, con-tact your Intermec representative for more information about this CD.When you upgrade the operating system, you erase the current configura-tion and replace it with the new default configuration. You will need to reset the network parameters on the CK60 Computer to reestablish com-munications with other devices in the network. In other words, if you upgrade the operating system and the default registry from the operating system has changed, the registry is rolled back to the new default.Running Diagnostics on Your CK60 ComputerFrontlight TestUse this test to ensure that your frontlight functions properly. It turns the frontlight on and off and sets brightness levels.This test performs a series of tests on the screen frontlight. Tap either Pass or Fail to confirm the results of each test before continuing. A green check mark indicates a pass; a red “X” indicates a fail. The dashed arrow indicates the action being tested.Battery InformationUse this test to view information about the battery voltage, charge levels, and AC line detection. The test would take less than a minute.Use the Intermec Diagnostics control panel applet on the CK60 Computer to analyze firmware problems and view system information. Tap Start > Settings > Control Panel, then double-tap the Intermec Diagnostics icon to access these tests and information. Select the appropriate test, then tap Start Test to begin. Press Esc to exit any of the tests.

Chapter 4 — Maintaining the CK60 ComputerCK60 Series Handheld Computer User’s Manual 95The Main Battery section displays the percentage of battery power remain-ing in the battery. You can continue using the battery until the CK60 Computer indicates that the battery is low; the battery light turns on and the low battery icon appears in the status bar.The Backup Battery section indicates the percentage of battery power remaining in the backup battery (super capacity). The main battery charges the backup battery.You can also use this screen to see the current volts and charging status.Display TestUse this test to check for display accuracy and ensure the physical display is mounted properly and is visible. This test runs until you either press a key or tap the display.This test performs a series of tests on the display. An explanation of what to expect is given before you press ACTION (Enter) to begin the test. When done testing an action, press Esc to end the test, then tap either Pass or Fail to confirm the results of the test before continuing to the next test. A green check mark indicates a pass; a red “X” indicates a fail; the dashed arrow indicates the action being tested.

Chapter 4 — Maintaining the CK60 Computer96 CK60 Series Handheld Computer User’s ManualHardware ConfigurationUse this test to read the hardware configuration and display it onscreen.The hardware configuration table shows important information about your CK60 Computer, such as the serial number, configuration number, model, software options, and scanner type. Share this information with your Inter-mec representative when consulting about hardware and software that may be installed at the factory.A green check mark indicates a pass; a blue question mark indicates infor-mation is not available; and a red “X” indicates inaccurate information.Keyboard (Keypad) TestUse this test to test the functionality of all the keys on your installed key-pad. This test runs continuously until you tap the screen to exit. Note that you do not test I key, or you will suspend the CK60 Computer. Press a key on the keypad for the screen to cover the same key with a block of color -- note the [8] key was pressed in the following illustration.Tap screen to exit the keypad testThe [8] key was pressed.

Chapter 4 — Maintaining the CK60 ComputerCK60 Series Handheld Computer User’s Manual 97LED TestUse this test to light each LED on the CK60 Computer to ensure each is working properly. This test continuously turns the LEDs on the CK60 Computer on until you press Esc to exit. There are multiple LED tests, tap OK on each test to go through the sequence, then tap either Pass or Fail to confirm the results of the test before continuing to the next test.The top portion of the display shows the area of the CK60 Computer being tested. The Color and State descriptions in the left column indicate what you should expect with each LED feature being tested.A green check mark indicates a pass; a blue question mark indicates infor-mation is not available or the feature was not tested; a red “X” indicates inaccurate information; a dashed arrow indicates the feature being tested.Memory InformationThis displays the RAM, ROM, and Disk on Chip (DOC) memory installed in the CK60 Computer and the size of each. Press Esc to exit.LED being testedColor LED should displayAction LED should perform

Chapter 4 — Maintaining the CK60 Computer98 CK60 Series Handheld Computer User’s ManualNetworking TestThis test validates each required level of network connectivity. Tap Start Tes t to begin the validation. Press Esc to exit.A green check mark indicates a validation; a blue question mark indicates the feature was not tested; a red “X” indicates the validation failed; a dashed arrow indicates the feature being tested.Read CPU RegistersUse this to read the CPU registers available in your CK60 Computer, then create a log file listing the registers. Tap Start Test to read the CPU regis-ters, then select any of the registers from the Register ID drop-down list to view its register address and register value. Press Esc to exit.

Chapter 4 — Maintaining the CK60 ComputerCK60 Series Handheld Computer User’s Manual 99Sound TestUse this to cycle through a frequency table, record audio through the microphone, and play back the recorded audio. Tap Start Test to begin the series, then tap either Pass or Fail to confirm the results of the test before continuing to the next test.A green check mark indicates a pass; a blue question mark indicates the fea-ture was not tested; a red “X” indicates the validation failed; a dashed arrow indicates the feature being tested.Touch Screen TestUse this test to ensure your touchscreen works properly. Draw anywhere on the screen with your stylus, press Esc to exit.

Chapter 4 — Maintaining the CK60 Computer100 CK60 Series Handheld Computer User’s ManualSoftware InventoryUse this test to get the latest version information of your critical software components. Press Esc to exit.Troubleshooting Your CK60 ComputerIf you have any problems using the CK60 Computer, look at the following for possible solutions:• Problems While Operating the CK60 Computer (page 101)• Problems While Configuring the CK60 Computer (page 102)• Problems While Configuring 802.1x Security (page 102)• Problems with Wireless Connectivity (page 104)• Problems Transmitting Data through the Serial Port (page 105)• Problems While Scanning Bar Codes (page 105)

Chapter 4 — Maintaining the CK60 ComputerCK60 Series Handheld Computer User’s Manual 101If you send the CK60 Computer in for service, it is your responsibility to save the computer data and configuration. Intermec is responsible only for ensuring that the keypad and other hardware features match the original configuration when repairing or replacing your device.Problems While Operating the CK60 ComputerProblem SolutionYou press I to turn on the CK60 Computer and nothing happens.• Make sure the backlight is on by pressing E.• Make sure you have a charged battery installed cor-rectly. For help, see “Using the Battery” on page 6.• The battery may be discharged. Replace the battery with a spare charged battery, or charge the battery and try again.•Perform a warm-boot.The Battery status LED is on. • If the battery status LED is a steady green, the battery is more than 95% charged and unit is on a charger.• If the battery status LED is blinking red, then the bat-tery is low. The speed of the blinking increases as the battery power gets increasingly lower.• If the battery status LED is a steady red, the main bat-tery is low, or if charging, then the LED remains red until the CK60 Computer reaches 95% charge status.• If the battery status LED is a steady yellow, then the CK60 Computer is on a charging source and there is no battery pack installed. This can also mean that the CK60 Computer is out of charging range 32° to 122°F (0° to 50°C). Once the CK60 Computer gets back in range, charging resumes and the LED changes to red or green.• If the battery status LED is a steady amber, then replace the battery pack.The CK60 Computer appears to be locked up and you cannot enter data.• Press I to turn off the CK60 Computer, then press I again to turn on the CK60 Computer.• Press and hold I for ten seconds to warm-boot the CK60 Computer.• Perform a cold-boot on the CK60 Computer. For help, see “Resetting Your CK60 Computer” on page 3.• Try reloading the firmware. For help, see “Upgrading the Operating System on your CK60 Computer” on page 94.• If the CK60 Computer will not boot or reset, contact your local Intermec representative for help.

Chapter 4 — Maintaining the CK60 Computer102 CK60 Series Handheld Computer User’s ManualProblems While Configuring 802.1x SecurityIf you have trouble configuring the computer for 802.1x security, check these problems and possible solutions.Problems While Configuring the CK60 ComputerProblem SolutionYou scan a configuration command, such as Beeper Vol-ume, and you hear three low beeps.If you are working in the Intermec Settings control panel applet, you cannot scan configuration commands. Exit the applet to scan configuration commands.You scan or enter an option for the Scanner Model con-figuration command and you hear three low beeps.You may have scanned or entered a Scanner Model com-mand that does not apply to the type of scanner that you have installed. Try scanning or entering the Scanner Model command again and select an option for the type of device you are using.You cannot type a character on the keypad or you can only type uppercase or lowercase letters.You may have accidentally locked a modifier key on the keypad. Check the CK60 Computer status bar to see if it contains an icon with a locked symbol. Press the necessary key sequence to unlock the key. For help, see “Using the Keypad” on page 8.Problems While Configuring 802.1x SecurityProblem SolutionThe CK60 Computer indicates that it is authenticated, but it does not communicate with the host.Make sure that the CK60 IP address, host IP address, subnet mask, and default router are properly configured for your network.Note: Do not perform a cold-boot on the CK60 Com-puter. Doing so resets the time and date. You must also update the time and date for the Certificate of Authority.The CK60 Computer does not appear to be authenticat-ing and a network connection icon does not appear on the status bar.The CK60 Computer may not be communicating with your access point. Make sure the network name on the CK60 Computer is the same as the network name (SSID) of the access point with which you are trying to commu-nicate. The default network name is “INTERMEC.”The 802.1x security network may not be active. Make sure that the server software is properly loaded and con-figured on the server PC. For help, see the documentation that shipped with your server software.

Chapter 4 — Maintaining the CK60 ComputerCK60 Series Handheld Computer User’s Manual 103A network connection icon appears in the status bar, but then disappears.The CK60 Computer may not be communicating with the access point that you want it to communicate with. Make sure that the network name on the CK60 Com-puter is the same as the network name of the access point with which you are trying to communicate. The default network name is “INTERMEC.”The access point with which you are trying to communi-cate may not be communicating with the server. Make sure your access point is turned on, properly configured, and has 802.1x security enabled.The CK60 Computer indicates that it is not authenti-cated.Make sure that:• The Users Name and Password parameters on your CK60 Computer match the user name and password on your authentication server. You may need to reenter the password on both your CK60 Computer and the authentication server.• On your authentication server, the user and group are allowed and the group policy is allowed to log into the server. For help, see the documentation that shipped with your authentication server software.• The IP address and secret key for your access point must match the IP address and secret key on your authentication server. You may need to reenter the IP address and secret key on both your access point and authentication server.• The authentication server software is running on the server PC.You are setting up multiple access points in a network, with different SSIDs, and the connection fails.The CK60 Computer does not save WEP key values when you change the SSID. Reenter the WEP key value after you change the SSID and select Apply Network Set-tings from the 802.11 Radio menu. You should now be able to connect to the different access points.You receive a message saying “The server certificate has expired or your system date is incorrect” after you per-form a cold-boot on the CK60 Computer.The date and time on the CK60 Computer are not saved when a cold-boot is performed. You need to reenter the date and time and then select Apply Network Settings from the 802.11 Radio menu.Problems While Configuring 802.1x Security (continued)Problem Solution

Chapter 4 — Maintaining the CK60 Computer104 CK60 Series Handheld Computer User’s ManualProblems with Wireless ConnectivityProblem SolutionWhen you turn on the CK60 Computer after it was sus-pended for a while (10-15 minutes or longer), it can no longer send or receive messages over the network.The host may have deactivated or lost your current termi-nal emulation session. In a TCP/IP direct connect net-work, you need to turn off the “KeepAlive” message (if possible) from the host so that the TCP session is main-tained while a CK60 Computer is suspended.The No Network Connection icon appears on the status bar. The CK60 Computer is not communicating with the access point.The CK60 Computer is not connected to the access point. Make sure the access point is turned on and oper-ating. You may also be using the CK60 Computer out of range of an access point. Try moving closer to an access point to reestablish communications.Make sure the CK60 Computer is configured correctly for your network. The radio parameters on the CK60 Computer must match the values set for all access points with which the CK60 Computer may communicate. For help, see “Configuring 802.11b/g Radio Communica-tions” on page 53.If you have an 802.11b radio, the radio initialization pro-cess may have failed. Try resetting the CK60 Computer. See “Resetting Your CK60 Computer” on page 3.If you have tried these possible solutions and the No Net-work Connection icon still appears, you may have a defective radio card. For help, contact your local Intermec representative.The CK60 Computer is connected to the Intermec Application Server or host computer and you move to a new site to collect data. The Network Connection icon was visible, but is now replaced with the No Network Connection icon.You may have gone out of range of an access point. Try moving closer to an access point or to a different location to reestablish communications. Once you are in range again, the Network Connection icon appears again. Any data you collected while out of range is transmitted over the network.The Network Connection icon is in the status bar, but you cannot establish a terminal emulation session with the host computer.There may be a problem with the host computer, a prob-lem with the connection between the Intermec Applica-tion Server and the host computer, or a problem with the connection between the access point and the host com-puter. Check with your network administrator to make sure the host is running and allowing users to login to the system.The Network Connection icon is in the status bar, but the host computer is not receiving any data from the CK60 Computer.In a UDP Plus network, there may be a problem with the connection between the Intermec Application Server and the host computer. Check with your network administra-tor or see the user’s manual for the Intermec Application Server.In a TCP/IP network, there may be a problem with the connection between the access point and the host com-puter. Check with your network administrator or use your access point user’s manual.

Chapter 4 — Maintaining the CK60 ComputerCK60 Series Handheld Computer User’s Manual 105Problems Transmitting Data through the Serial PortIf you are having problems sending or receiving data through the integrated serial port on the CK60 Computer, check these possible problems:• Make sure the CK60 Computer is connected to the PC, host computer, or RS-232 serial device using the appropriate cable adapter and null modem cable.• If the CK60 Computer is in a communications dock, make sure that the communications dock is connected to the serial device using the appro-priate cable.For more information on using the serial port, see “Configuring Serial Communications” on page 53.Problems While Scanning Bar CodesProblem SolutionYou cannot see a red beam of light from the scanner when you press the Scan button and aim the scanner at a bar code label.There are two possible problems:• You may be too far away from the bar code label. Try moving closer to the bar code label and scan it again.• You may be scanning the bar code label “straight on.” Change the scanning angle and try again.You can test the effective range of the scanner. Move within 2 feet of a wall and test the scanner. You need to be within the scanning range to scan bar code labels. For help scanning bar codes, see “Scanning Bar Codes” on page 4.When you release the Scan button or handle trigger, the Good Read light does not turn off.The Good Read light will remain on if you configure the CK60 Computer to use continuous/edge triggering. If you configure the CK60 Computer for level triggering and the Good Read light remains on, there may be a problem. Press the Scan button or pull the trigger again without scanning a bar code label. If the light is still on, contact your local Intermec representative.

Chapter 4 — Maintaining the CK60 Computer106 CK60 Series Handheld Computer User’s ManualThe input device attached to the CK60 Computer does not appear to work well or read bar code labels very quickly.Try setting the Scanner Model command to the specific input device you have attached. Check the bar code sym-bologies you have enabled on the CK60 Computer. Enable only the symbologies that you are using.The scanner will not read the bar code label. Make sure you aim the scanner beam so it crosses the entire bar code label in one pass.The angle you are scanning the bar code label may not be working well, or you may be scanning the label “straight on.” Try scanning the bar code label again, but vary the scanning angle.The bar code label print quality may be poor or unread-able. To check the quality of the bar code label, try scan-ning a bar code label that you know will scan. Compare the two bar code labels to see if the bar code quality is too low. You may need to replace the label that you cannot scan.Make sure the bar code symbology you are scanning is enabled. Use the Intermec Settings control panel applet to check the symbologies. On the Scanners, Symbologies option, expand the Symbologies option beneath each of the devices listed (scanner, virtual wedge) to see what symbologies has a check mark. If there is no check mark, then the bar code symbology is disabled. Check the sym-bology to enable it, then try scanning the bar code label again.Make sure that the application you are running on the CK60 Computer is expecting input from a bar code. You may need to type this information instead of scanning it.The scanner does not read the bar code labels quickly, or the scanning beam seems to be faint or obscured.The scanner window may be dirty. Clean the window with a solution of ammonia and water. Wipe dry. Do not allow abrasive material to touch the window.You scan a valid bar code label to enter data for your application. The data decoded by the scan module does not match the data encoded in the bar code label.The CK60 Computer may have decoded the bar code label in a symbology other than the label’s actual symbol-ogy. Try scanning the bar code label again. Make sure you scan the entire label.To operate the CK60 Computer quickly and efficiently, you should enable only the bar code symbologies that you are going to scan.Problems While Scanning Bar Codes (continued)Problem Solution

Chapter 4 — Maintaining the CK60 ComputerCK60 Series Handheld Computer User’s Manual 107Cleaning the Scanner Window and CK60 ScreenTo keep the CK60 Computer in good working order, you may need to clean both the scanner window and the CK60 screen.Clean the scanner window and CK60 screen as often as needed for the environment in which you are using the CK60 Computer. To clean the CK60 Computer, use a solution of ammonia and water.Press I to turn off the CK60 Computer. Dip a clean towel or rag in the ammonia solution and wring out the excess. Wipe off the scanner window and screen. Do not allow any abrasive material to touch these surfaces. Wipe dry.You receive a message reading “Scanner Communication Failure” when trying to connect a 1551E or 1553 decoded scanner.Make sure that:• You are using the correct cable.• The scanner cable is attached correctly. When you attach the scanner to the port, it should emit a single power up beep.• Try enabling the port state using the Intermec Settings control panel applet.• Try upgrading the scanner firmware.• Select ASCII as the scanner model.Your 1551E or 1553 scanner was working fine, but after changing the port setting you cannot change the configu-ration.The 1551E or 1553 scanner port must be using the cor-rect RS-232 settings to allow configuration in the Inter-mec Settings control panel applet. Try disabling, then enabling the scanner port state.Configuration settings in the Intermec Settings applet do not match the settings on your 1551E or 1553 Scanner.Try disabling, then enabling the scanner port state to syn-chronize the CK60 Computer settings with the scanner.There are no user-serviceable parts inside the CK60 Computer. Open-ing the unit will void the warranty and may cause damage to the inter-nal components.Attention: Le CK60 ne contient pas de pièces réparables par l’utili-sateur. Le fait d’ouvrir l’unité annule la garantie et peut endommager les pièces internes.Problems While Scanning Bar Codes (continued)Problem Solution

Chapter 4 — Maintaining the CK60 Computer108 CK60 Series Handheld Computer User’s Manual

CK60 Series Handheld Computer User’s Manual 1095Network SupportThe CK60 Series Handheld Computer automatically installs the appropri-ate software for radio use when the unit is powered on. It provides wireless connectivity via the Wireless Local Area Network (WLAN) using a radio option that provides up to 54 Mbps. Note: Desktop icons and control panel applet icons are shown to the left. Any place that Start is mentioned, tap the following Windows icon in the bottom, left corner of your CK60 desktop.

$Chapter 5 — Network SupportCK60 Series Handheld Computer User’s Manual 111AutoIP/DHCPAutomatic Private IP Addressing (AutoIP) is enabled by default in Win-dows CE. To remain compatible with other versions of Windows CE, enable this setting. You can configure the registry settings in the following to set the required AutoIP/DHCP behavior:HKEY_LOCAL_MACHINE\Comm\PRISMNDS1\TcpIpOther registry keys that can modify the behavior of AutoIP are as follows. You can find the appropriate settings and behavior of each of the AutoInt-erval, AutoIP, AutoMask, AutoSeed, and AutoSubnet keys in Microsoft Help.When a TCP/IP client cannot find a DHCP server, it generates an AutoIP address from the 169.254.xxx.xxx block. The client then tries to check for a DHCP server every 15 seconds and if a DHCP server is found, the client drops the AutoIP address and uses the address from the DHCP server.To disable AutoIP, set the AutoCfg registry entry to “0.” If a DHCP server cannot be found, instead of using AutoIP, the system will display the “Unable to obtain a server assigned IP address” message.Note: If you try to disable AutoIP using a CAB file to set the registry value for AutoIP, remember to set the EnableDHCP value to “1” to keep DHCP enabled.Note: Use DhcpRetryDialogue and DhcpMaxRetry registry settings to extend the number of attempts that a DHCP client makes to get a DHCP address.Note: Change the AutoInterval registry key value to make the client retry more often to obtain a DHCP address.$

Intermec Technologies 802UIAG 802UIAG User Manual CK60UserManual WinCE

Intermec Technologies Corporation 802UIAG CK60UserManual WinCE

Contents

Users Manual

Navigation menu

Namespaces

Views

Navigation