Intermec Technologies ABTM3-2 ABTM3-2 User Manual Product Profile
Intermec Technologies Corporation ABTM3-2 Product Profile
Contents
- 1. Manual Insert with Compliance Statements
- 2. Product Profile
Product Profile
BlueCore 01b
BlueCore 01b Product Data Sheet
TM
bc01b-ds-003d
Product Data Sheet
Production Information
Single Chip Bluetooth Device
Product Data Sheet For:
BC01b-USB
(USB and UART version)
(BGA Packaging)
BC01b-URT
(UART only version)
(BGA Packaging)
BC01bv-USB
(USB and UART version)
(VFBGA Packaging)
BC01bv-URT
(UART only version)
(VFBGA Packaging)
BlueCore 01b is a single chip radio and baseband IC
for Bluetooth 2.4GHz radios, and is implemented in
CMOS technology.
When used with external flash containing the CSR
Bluetooth software stack, it provides a fully compliant
Bluetooth system for data and voice communications.
General Description
Figure 1: BlueCore01b Block Diagram
RAM
DSP
µC
I/O
2.4GHz
Radio
SPI
UART/USB
PIO
PCM
XTAL EXTERNAL
FLASH
RF IN
RF OUT
Laptop and Desktop PCs
Applications
Mobile Phones
Cordless Headsets
Personal Digital Assistants (PDAs)
Computer Accessories (Compact Flash,
PCMCIA and SD cards)
Domestic and Industrial Appliances
The design is optimised to require very few external
RF components to facilitate rapid design of the applica-
tion printed wiring board, and therefore the fastest pos-
sible time to market and lowest overall cost.
A low intermediate frequency receiver is utilised to
allow on-chip channel filtering. All hardware is fully
compliant with the Bluetooth specification.
The device operates from a regulated supply in the
range 2.7V to 3.3V and is available in an 81-ball BGA
package.
Device Features
Compliant to Bluetooth specification V1.1
Small footprint in 8mm x 8mm 81-ball BGA
Fully integrated RF block with no external
adjustments or trim
USB V1.1 compliant
Qualified Bluetooth firmware included
Extensive built-in-self-test to minimise end
product final test time
RF reference designs available
Low power consumption/optimisation
Support for up to 7 slaves
TM
TM
TM
TM
BlueCore 01b Product Data Sheet
TM
bc01b-ds-003d
Product Data Sheet
Production Information
Radio
Qualified Bluetooth component
Extensive built-in-self-test to minimise end
product final test time
No external trimming required in production
Full RF reference designs available
Transmitter
Up to 2dBm output power for Class 2
operation
Support for external PA for Class 1 operation
with level control and RSSI >30dB dynamic
range
Receiver
High out-of-band blocking immunity,
sufficient for embedding into mobile phones
Integrated channel filters
Synthesiser
Fully integrated; no external VCO varactor
diode or resonator
Closed loop during TX burst resulting in no
carrier drift
Baseband
All packet types supported. Piconet and
Scatternet support
Multiple physical application interfaces:
UART:
PCM:
USB:
Firmware
Link Controller, Link manager and HCI
Extensive power saving modes, including
PARK, HOLD and SNIFF
Ancillary Features
Internal low-dropout regulator with low stand-
by current (uses one external transistor)
Crystal oscillator with digital trimming allows
use of low cost reference crystal
Trancoders for A-law, µ-law and CVSD for
HCI voice traffic
Data and voice to 1.5Mbs-1
Programmable, for voice: 13-bit
8kss-1 synchronous bi-directional
serial audio interface
Data and voice. V1.1 Compliant.
Supports OHCI and UHCI
Digital demodulator for superior co-channel
rejection
Power-On-Reset
Optional build includes embedded L2CAP,
RFCOMM and Service Discovery
Key Features
Page 2 of 15
Key Features
Support for up to seven slaves
BlueCore 01b Product Data Sheet
TM
bc01b-ds-003d
Product Data Sheet
Production Information Page 3 of 15
Microcontroller
Interrupt
controller
Event
timer
RISC
microcontroller
Parallel
I/O
PIO[2]USB_PULL_UP
PIO[3]USB_WAKE_UP
PIO[4]USB_ON
PIO[5]/USB_DETACH
PIO[6]
PIO[7]
VSS_MEM
VSS_PADS
VSS_CORE
Baseband DSP
SPI_CSB
SPI_CLK
SPI_MOSI
SPI_MISO
PCM_OUT
PCM_IN
PCM_SYNC
PCM_CLK
UART_TX
UART_RX
UART_RTS/USB_D+
UART_CTS/USB_D
-
Audio
PCM
interface
UART/USB
Synchronous
serial
interface
Memory
management
unit
Burst
mode
controller
RAM
Memory
mapped
control/status
registers
Physical
layer
DSP
hardware
engine
RESET
TEST_A
TEST_B
SCAN_EN
VDD_MEM
VDD_PADS
VDD_CORE
VREG
XTAL_OUT
XTAL_IN
VDD_VCO
Clock
generator
V regulator
VDD_RADIO
RSSI
PIO[0]/RXEN
RF_IN
TX_A
TX_B
PIO[1]TXEN
PA
level
control
PA DAC
IQ DEMOD
RF
synthesiser
/N/N+1
Tune
LOOP_FILTER
ADC
Demodulator
VSS_VCO
VSS_RADIO
+45
-45
RF Receiver
RF Transmitter
IQ MOD
TX_PWR
RF Synthesiser
Fref
External
memory
driver
CSB
A[17:0]
D[15:0]
WEB
18
16
REB
LNA
Figure 2: BlueCore01b Device Diagram
Device Diagram
Device Diagram
BlueCore 01b Product Data Sheet
TM
bc01b-ds-003d
Product Data Sheet
Production Information
Page 4 of 15
VSS_PADS VDD_PADS UART_TX UART_RTS /
USB_D+ VDD_MEM VSS_MEM WEB A[0] A[1]
PIO[3] /
USB_
WAKE_UP
PIO[4] /
USB_ON UART_RX UART_CTS /
USB_D- PCM_SYNC A[6] A[3] A[4] A[2]
RESET
PIO[2] /
USB_PULL_
UP
SPI_MISO SPI_MOSI PCM_IN D[15] A[9] A[7] A[5]
TX_PWR PIO[0] /
RXEN SPI_CLK SPI_CSB PCM_CLK A[12] A[11] A[10] A[8]
RF_IN VSS_RADIO PCM_OUT SCAN_EN NC D[13] A[15] A[13] A[14]
TX_B VSS_RADIO PIO[1] /
TXEN
PIO[5] /
USB_
DETACH
D[11] D[12] D[10] A[17] CSB
TX_A VDD_RADIO PIO[6] PIO[7] D[14] D[7] D[9] A[16] REB
VSS_VCO LOOP_
FILTER TEST_B VDD_CORE VSS_CORE D[6] D[4] D[3] D[0]
VDD_VCO TEST_A XTAL_OUT XTAL_IN VREG D[8] D[5] D[2] D[1]
123456789
A
B
C
D
E
F
G
H
J
Figure 3: BlueCore01b Device Pinout
Device Pinout Diagram
Note:
(1) = Not connected.
Device Pinout Diagram
Orientation from top of device
(1)
BlueCore 01b Product Data Sheet
TM
bc01b-ds-003d
Product Data Sheet
Production Information Page 5 of 15
Terminal Name Pad Type DescriptionBall
RF_IN - Receiver RF inputE1
Transmitter RF outputG1
Radio
TX_B - Transmitter RF output (complement of TX_A)F1
PIO[1] / TXEN Bidirectional
pulled down Control output for external switch or PA (if fitted)F3
PIO[0] / RXEN Bidirectional
pulled down
Control output for external switch or LNA
(if fitted)
D2
TX_PWR Current DAC output to set external PA levelD1
XTAL_IN Sense for crystal or external clock inputJ4
XTAL_OUT Drive for crystalJ3
Synthesiser and Oscillator
A[17:0] Address bus for external memory
(1)
WEB Write enable for external memory (active low)A7
Data bus for external memory
External Memory Port
REB Read enable for external memory (active low)G9
CSB Chip select for external memory (active low)F9
PCM_SYNC Synchronous data strobeB5
PCM_IN Synchronous 8kss-1 data input
C5
Synchronous data clockD5
PCM Interface
PCM_OUT Synchronous 8kss-1 data outputE3
-
-
LOOP_FILTER Synthesiser external loop filterH2
CMOS output
D[15:0] Bidirectional
CMOS output
CMOS output
CMOS output
(1)
Bidirectional
pulled down
CMOS input
pulled down
CMOS output
-
TX_A -
Current DAC
PCM_CLK Bidirectional
pulled down
Note:
(1) See Address and Data Bus tables at the end of this section.
Device Terminal Functions
Device Terminal Functions
BlueCore 01b Product Data Sheet
TM
bc01b-ds-003d
Product Data Sheet
Production Information
Page 6 of 15
SPI clockD3
Test and Debug
SPI_MOSI CMOS input, 5V tolerant
pulled down SPI data inputC4
UART_TX UART data outputA3
UART_RX UART data inputB3
UART or USB(1)
UART_RTS / USB_D+ CMOS output UART ready to send / USB D+A4
PIO[2] / USB_PULL_UP Bidirectional
pulled down USB pull-up (via 1.5kΩ resistor to D+)
C2
UART_CTS / USB_D- CMOS input UART clear to send / USB D-B4
CMOS output
PIO[3] / USB_WAKE_UP Bidirectional
pulled down
Output goes high to wake up PC when in USB
mode
B1
Terminal Name Pad Type DescriptionBall
CMOS input, 5V tolerant
pulled down
PIO[4] / USB_ON Bidirectional
pulled down
USB on (input senses when VBUS is high,
wakes BlueCore01b)
B2
PIO[5] / USB_DETACH Bidirectional
pulled down Chip detaches from USB when this line is highF4
Device Terminal Functions (continued)
SPI_CLK CMOS input, 5V tolerant
pulled down
SPI_CSB SPI chip selectD4
CMOS input, 5V tolerant
pulled up
TEST_A -Analog test port AJ2
SPI_MISO CMOS output Tristate SPI data outputC3
PIO[0] /RXEN Bidirectional
pulled down
PIO[2] /USB_PULL_UP Bidirectional
pulled down Input/Output port or USBC2
PIO[1] /TXEN Bidirectional
pulled down Input/Output port or high when TX is enabledF3
PIO Port
PIO[3] /USB_WAKE_UP Bidirectional
pulled down
RESET CMOS input with weak
internal pull-down ResetC1
Input/Output port or high when RX is enabledD2
Input/Output port or USBB1
TEST_B -Analog test port BH3
SCAN_EN CMOS input with weak
internal pull-down For test purposes only (leave unconnected)E4
PIO[4] /USB_ON Input/Output port or USBB2
PIO[5] /USB_DETACH Input/Output port or USB
PIO[7] Bidirectional
pulled down Input/Output portG4
Bidirectional
pulled down
Bidirectional
pulled down F4
PIO[6] Bidirectional
pulled down Input/Output portG3
Note:
(1) BC01b-USB supports both USB and UART (but not simultaneous operation). BC01b-URT supports UART only.
BlueCore 01b Product Data Sheet
TM
bc01b-ds-003d
Product Data Sheet
Production Information
Terminal Ball
A[1]
A[0]
Address Lines
Terminal Ball
D[1] J9
D[0] H9
Data Bus
A[4]
A[5]
A[6]
A[8]
A[9]
D[2] J8
D[3] H8
D[4] H7
D[5] J7
D[6] H6
A8
A9
B8
C9
B6
D9
C7
A[10] D8
A[11] D7
A[12] D6
A[13] E8
A[14] E9
A[15] E7
A[16] G8
A[17] F8
D[7] G6
D[8] J6
D[9] G7
D[10] F7
D[11] F5
D[12] F6
D[13] E6
D[14] G5
D[15] C6
VREG LDO voltage regulator output to external pass
transistor
J5
Power Supplies and Control
-
VDD_CORE VDD For internal digital circuitryH4
Terminal Name Pad Type DescriptionBall
VDD_RADIO For RF circuitryG2VDD
VDD_VCO For VCO and synthesiser
VDD_PADS For all Input/Output except memory portA2VDD
VDD_MEM For external memory portA5VDD
VSS_CORE For internal digital circuitryH5VSS
VSS_RADIO For RF circuitryF2, E2VSS
VSS_VCO For VCO and synthesiserH1VSS
VSS_PADS For Input/Output except memory portA1VSS
VSS_MEM For external memory portA6VSS
Page 7 of 15
Device Terminal Functions (continued)
J1VDD
A[2] B9
A[3] B7
A[7] C8
BlueCore 01b Product Data Sheet
TM
bc01b-ds-003d
Product Data Sheet
Production Information
Page 8 of 15
Absolute Maximum Ratings
Storage Temperature -30°C 85°C
Supply Voltage, VDD -0.4V 3.6V
Rating
Other Terminal Voltages (except 5V tolerant) VSS-0.4V VDD+0.4V
5V Tolerant Terminals -0.4V 5.5V
Temperature -20°C(1) 70°C(1)
Supply Voltage, all VDD terminals 2.7V 3.3V(2)
Operating Condition
Supply Voltage, VDD_PADS for USB operation 3.0V 3.4V
0.3V
Recommended Operating Conditions
Notes:
(1)The device is fully functional across this range.
(1) The guaranteed radio performance is shown in the Radio Characteristics section.
(2)The recommended supply voltage is 3.3V (to be compatible with industry standard regulators) but
(2) the device will function up to 3.4V.
Input/Output Terminal Characteristics
VDD = 3.0V (except as specified)
-
-
0.3V x VDD
VDD+0.4
V
V
-0.4
0.7VDD
Input voltage
VIL input logic level low
VIH input logic level high
-
-
-
1
1
-125
125/12.5(1)
-
-
-
-
0.2
-
1
10
-
VDD-0.2
-1
2.5
Output voltage
VOL output logic level low
(IO= 4.0mA)
VOH output logic level high
(IO= -4.0mA)
Tristate leakage current
CIInput capacitance
Note:
(1) PIO terminals have weak pull-down resistors (1/10th current of standard pull-down resistors).
Min Max
Min Max
µA
µA
µA
V
V
µA
pF
Difference between any two VDD terminals -
-1
-20
20/2(1)
Input current
CMOS input only
(VI= 0V or VI=3.3V, VDD = 3.3V)
CMOS input + pull-up
(VI= 0V, VDD =3.3V)
CMOS input + pull-down
(VI=3.3V, VDD =3.3V)
Electrical Characteristics
Electrical Characteristics
Digital Terminals Min UnitMaxTyp
BlueCore 01b Product Data Sheet
TM
bc01b-ds-003d
Product Data Sheet
Production Information
Output regulation voltage (1)
Maximum allowable voltage on Vreg pad
Bias current
Maximum regulation current
Voltage Regulator (VREG) Min UnitMaxTyp
Power-on Reset
Input/Output Terminal Characteristics (continued)
2.40
2.60
200
2.50
2.70
220
V
V
mV
Min UnitMaxTyp
2.30
2.50
180
V
V
-
0.7VDD_PADS
VDD falling threshold
VDD rising threshold
Hysteresis
Input threshold
VIL input logic level low
VIH input logic level high
USB Terminals Min Typ
2.74
3.1
-
5
-
2.79
3.15
-
-
-
2.84
3.2
5
-
100
V
V
V
µA
mA
Electrical Characteristics (continued)
UnitMax
-
-
0.3VDD_PADS
-
µA
-1Input leakage current - 1
pF2.5CI Input capacitance - 10
V
V
0
2.8
Output levels to correctly terminated USB cable
VOL input logic level low
VOH input logic level high
-
-
0.2
VDD_PADS
Unit
SCO connection HV3 (1s interval sniff mode) (Slave) mA
mA
SCO connection HV1 (Slave) mA
PeakMode Avg
Power Consumption(1)
VDD = 3.0V Temperature = 20°C
78
ACL data transfer 115.2kbps UART (Master)
-
-
-29
mAACL data transfer 720kbps USB (Master) -82
mAPeak current during RF burst 135-
41
SCO connection HV3 (1s interval sniff mode) (Master) mA-42
SCO connection HV1 (Master) mA77 -
mAACL data transfer 720kbps USB (Slave) -81
mAACL connection, Sniff Mode 40ms interval, 38.4kbps UART -5.5
mAACL connection, Sniff Mode 1.28s interval, 38.4kbps UART -1.1
mAParked Slave, 1.28s beacon interval, 38.4kbps UART -1.1
µA
Deep Sleep Mode 90
Page 9 of 15
Note:
(1) Power consumption is for BC01b-USB module including external flash ROM.
Note:
(1)The regulated voltage is selected by a variable stored in the flash ROM.
BlueCore 01b Product Data Sheet
TM
bc01b-ds-003d
Product Data Sheet
Production Information
Unit
Sensitivity at 0.1% BER (1) dBm
dB
Maximum received signal (1) dBm
Bluetooth
Specification
Receiver
Radio Characteristics at 20°C
VDD = 3.0V f=2.45GHz
-5
C/I co-channel (1)
≤-70
≥-20
≤11
9
dBAdjacent channel selectivity C/I 1MHz (1) ≤0
-2
dB2nd adjacent channel selectivity C/I 2MHz (1) ≤-30
-34
dB3rd adjacent channel selectivity C/I >3MHz (1) (2) ≤-40
-45
-79
Max
-
-
-
-
-
-75
-
-
-
-
-
-
dBm1dB compression point at 1.9GHz --12 --
Bluetooth
Specification
Transmitter Typ Max
Min
RF transmit power (1) -6 to +42 6-2
≥16
30
RF power range control resolution -2
20dB bandwidth for modulated carrier ≤1000
885
-
-
-
-
-
3rd adjacent channel transmit power (1) ≤-40
Page 10 of 15
Unit
dBm
dB
dB
kHz
dBc
TypMin
-
Electrical Characteristics (continued)
dBImage rejection C/I (1) (3) ≤-9
-14
dBmMaximum level of intermodulation interferers (1) (4) ≤-39
-30
-
-
-
-
RF power control range (1) -
2nd adjacent channel transmit power (1) ≤-20
-dBc-47 -
--52
Sensitivity at 0.1% BER (1) dBm
Radio Characteristics at 50°C
VDD = 3.0V f=2.45GHz
≤-70
-74 -70-
Unit
RF transmit power (1) dBm
Bluetooth
Specification
Transmitter Typ
-6 to +4-1
Max
3
Min
-5
Notes:
(1) Measured according to the Bluetooth specification.
(2) Up to five spurious responses within Bluetooth limits are allowed.
(3) At carrier -3MHz.
(4) Measured at f1-f2=5MHz.
These results were measured on the BlueCore01b chip. Results shown relate to power at the output
of the balun and at the input to the RX matching network. The loss of the RF filter and switch in the
application circuit are not taken into account.
BlueCore01b meets the Bluetooth specification when used in a suitable application circuit between
-20°C and 50°C. When used with an off-chip LNA the sensitivity can be enhanced and the operating
temperature range extended.
Unit
Bluetooth
Specification
Receiver Typ MaxMin
Sensitivity at 0.1% BER (1) with additional off-chip LNA dBm
≤-70
-89 --
Sensitivity at 0.1% BER (1) with additional off-chip LNA dBm
≤-70
-88 --
BlueCore 01b Product Data Sheet
TM
bc01b-ds-003d
Product Data Sheet
Production Information Page 11 of 15
Top View Bottom View
Package Dimensions
Package Dimensions
Figure 4: BlueCore01b package dimensions
D
E
A
B
C
D
E
F
G
H
J
9876543 21
SEATING
PLANE
SEE DETAIL K
A
B
C
D
E
F
G
H
J
123456 789
DETAIL K
DIM MIN MAX NOTES
A
A1
A2
A3
0.35
D
E
e
D1
E1
1
2
3
DIMENSION b IS MEASURED AT THE MAXIMUM
SOLDER BALL DIAMETER PARALLEL TO DATUM
PLANE Z.
DATUM Z IS DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
PARALLELISM MEASUREMENT SHALL EXCLUDE
ANY EFFECT OF MARK ON TOP SURFACE OF
PACKAGE.
0.8 1
0.25 0.35
0.22 REF
0.45 REF
0.45
8 BSC
8 BSC
0.8 BSC
6.4 BSC
6.4 BSC
BC01bv-USB/URT VFBGA 81 BALLS
8X8X1 PKG PITCH POD
(JEDEC MO-225)
PIN A1
Z
A
(A2)
(A3)
E1
D1
2
A1
3
0.1 Z
0.1 Z
8X e
PIN A1
b
∅
1
b
DIM MIN MAX NOTES
A
A1
A2
A3
0.35
D
E
e
D1
E1
UNIT
MM
1
2
3
DIMENSION b IS MEASURED AT THE MAXIMUM
SOLDER BALL DIAMETER PARALLEL TO DATUM
PLANE Z.
DATUM Z IS DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
PARALLELISM MEASUREMENT SHALL EXCLUDE
ANY EFFECT OF MARK ON TOP SURFACE OF
PACKAGE.
1.1 1.50
0.25 0.35
0.36 REF
0.8 REF
0.45
8 BSC
8 BSC
0.8 BSC
6.4 BSC
6.4 BSC
BC01b-USB/URT BGA 81 BALLS
8X8X1 PKG PITCH POD
(JEDEC MO-205)
b
UNIT
MM
BlueCore 01b Product Data Sheet
TM
bco1b-ds-003d
Product Data Sheet
Production Information
BlueCore 01b Product Data Sheet
TM
0
50
100
150
200
250
Time in minutes
0
24
Temperature ( C)°
0
50
100
150
200
250
0
2
4
6
8
10
12
14
16
18
20
22
0
Time in minutes
24
Temperature ( C)°
Figures 5 and 6 show the re-flow solder profile that was used to qualify the BlueCore01b packages.
This temperature profile was repeated three times during the qualification of the BlueCore01b packages with a
maximum temperature of 235°C.
Assembly Guidelines
Assembly Guidelines
Page 12 of 15
Whereas the above profile was used to confirm the reliablility of the BlueCore01b packages, the following
(figure 6) is the recommended solder profile to be used when assembling BlueCore01b onto a circuit board.
Recommended Re-flow Solder Profile
The recommended re-flow solder profile is shown in figure 6.
Important points to note are:
Maximum peak temperature should not exceed 220°C.
Time above liquidus should be between 45 to 90 seconds.
Rapid quenching provides superior cosmetic appearance and bond strength.
Figure 5: Re-flow solder profile 1
Figure 6: Re-flow solder profile 2
•
•
•
BlueCore 01b Product Data Sheet
TM
bco1b-ds-003d
Product Data Sheet
Production Information
BlueCore 01b Product Data Sheet
TM
Interface Version Shipment Method
USB and UART Tray (dry pack)
UART only Tape and reel
UART only Tray (dry pack)
Order Number
BC01b-USB-TR
BC01b-USB
BC01b-URT-TR
BC01b-URT
Contact CSR Worldwide
To contact a CSR representative, please go to www.csr.com/contacts.htm
CSR Japan
CSR KK
Miyasaka LK Building 3F
43-23, 3 Chome Shimorenjaku
Mitaka-shi, Tokyo
Japan 181-0013
Tel: +81 (0) 422 40 4760
Fax: +81 (0) 422 40 4765
e-mail: sales@csr.com
CSR Head Office
Cambridge Science Park
Milton Road
Cambridge, CB4 0WH
United Kingdom
Tel: +44 (0) 1223 692 000
Fax: +44 (0) 1223 692 001
e-mail: sales@csr.com
CSR USA
1651 N. Collins Blvd.
Suite 210
Richardson
TX75080
USA
Tel: +1 972 238 2300
Fax: +1 972 231 1440
e-mail: sales@csr.com
CSR Denmark
Novi Science Park
Niels Jernes Vej 10
9220 Aalborg East
Denmark
Tel: +45 72 200 380
Fax: +45 96 354 599
e-mail: sales@csr.com
CSR Singapore
Blk 5, Ang Mo Kio
Industrial Park 2A
AMK Tech II, #07-08
Singapore 567760
Tel: +65 484 2212
Fax: +65 484 2219
e-mail: sales@csr.com
USB and UART Tape and reel
Ordering and Contact Information
Ordering and Contact Information
Page 13 of 15
USB and UART Tray (dry pack)
UART only Tape and reel
UART only Tray (dry pack)
BC01bv-USB-TR
BC01bv-USB
BC01bv-URT-TR
BC01bv-URT
USB and UART Tape and reel
BlueCore 01b Product Data Sheet
TM
bco1b-ds-003d
Product Data Sheet
Production Information
BlueCore 01b Product Data Sheet
TM
The progression of CSR Product Data Sheets follows the following format:
a) Advance Information
Information for designers on the target specification for a CSR product in development.
All detailed specifications including pinouts and electrical specifications may be changed by CSR without
notice.
b) Pre-Production Information
Final pinout and mechanical dimensions. All electrical specifications may be changed by CSR without notice.
c) Production Information
Final Data Sheet including the guaranteed minimum and maximum limits for the electrical specifications.
Production Data Sheets supersede all previous document versions.
The status of this Data Sheet is Production Information.
The long form version of this Data Sheet is available separately from CSR.
Status of Information
Status of Information
Page 14 of 15
Trademarks, Patents and Licenses
BlueCore is a trademark of CSR.
Bluetooth and the Bluetooth logos are trademarks owned by Bluetooth SIG Inc, USA and licensed to CSR.
All other product, service, and company names are trademarks, registered trademarks, or service marks of
their respective owners.
The publication of this information does not imply that any license is granted under any patent or other rights
owned by CSR.
CSR reserves the right to make technical changes to its products as part of its development programme.
While every care has been taken to ensure the accuracy of the contents of this document, CSR cannot accept
responsibility for any errors.
CSR Ltd 2001
Life Support Policy and Use in Safety-Critical Applications
CSR’s products are not authorised for use in life-support or safety-critical applications.
BlueCore 01b Product Data Sheet
TM
bco1b-ds-003d
Product Data Sheet
Production Information
BlueCore 01b Product Data Sheet
TM
Date: Revision: Reason for Change:
21st Feburary 2001 bc01b-ds-003a Input/Output terminal characteristics information updated
23rd March 2001 bc01b-ds-003b Minor modifications to RF characteristics based upon
latest characterisation data
BlueCore01b Product Data Sheet
bc01b-ds-003d
July 2001
Record of Changes
6th July 2001 bc01b-ds-003c System features added and power consumption figures
expanded
26th July 2001 bc01b-ds-003d Package dimensions added for VFBGA packaging
Page 15 of 15
Record of Changes