Intermec Technologies CK31MIG2 802MIG2 User Manual 075206 008
Intermec Technologies Corporation 802MIG2 075206 008
Contents
Compliance Insert
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1305508 |
| Application ID | 57lzz/v7z7wOk4n6aRxaqw== |
| Document Description | Compliance Insert |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 112.77kB (1409679 bits) |
| Date Submitted | 2010-07-02 00:00:00 |
| Date Available | 2010-07-02 00:00:00 |
| Creation Date | 2006-02-14 15:53:15 |
| Producing Software | Acrobat Distiller 9.3.2 (Windows) |
| Document Lastmod | 2010-06-30 15:31:32 |
| Document Title | 075206-008.fm |
| Document Creator | FrameMaker 8.0 |
| Document Author: | mfisher |
Model CK31 Compliance Insert Complies with IDA Standards DA 102905 ertified for use in Hong Kong OFTA Certificate No. LP206289 For Users in the United States and Canada Caution: This marking indicates that the user should read all included documentation before use. Attention: Ce marquage indique que l’usager doit, avant l’utilisation, lire toute la documentation incluse. This product conforms to the following approvals. The users of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended, or changes to this product that are not approved by Intermec Technologies Corporation, may void the compliance of this product and may result in the loss of the user’s authority to operate the equipment. FCC Digital Emissions Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the radio or television receiving antenna. • Increase the separation between the computer equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected. • Consult the dealer or an experienced radio television technician for help. Canadian Digital Apparatus Compliance This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Conformité aux normes canadiennes sur les appareils numériques Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilleur du Canada. Battery Information Caution: The battery pack used in this device may ignite, create a chemical burn hazard, explode, or release toxic materials if mistreated. Do not incinerate, disassemble, or heat above 100°C (212°F). Charge only with Intermec Models AC1, AC2, AC3, AD1, and AD2. Do not short circuit; may cause burns. Keep away from children. Use only Intermec battery pack Model AB1G. Risk of fire or explosion if incorrect battery pack is used. Promptly dispose of used battery pack according to the instructions. Attention: Le bloc-piles utilisé dans cet appareil peut prendre feu, constituer un risque de brûlure chimique, exploser ou dégager des substances toxiques s’il est manipulé de façon inappropriée. Ne pas jeter au feu, démonter ou chauffer à plus de 100 °C (212 °F). Ne charger qu’avec les dispositifs Intermec AC1, AC2, AC3, AD1, et AD2. Ne pas court-circuiter; cela pourrait causer des brûlures. Garder hors de la portée des enfants. N’utiliser que le modèle de bloc-piles Intermec AB1G. L’utilisation d’un mauvais bloc-piles pourrait constituer un risque d’incendie ou d’explosion. Mettre rapidement au rebut tout bloc-piles usé, conformément aux instructions. Battery Recycling Information This product contains or uses a lithium ion (Li-ion) main battery. When the battery reaches the end of its useful life, the spent battery should be disposed of by a qualified recycler or hazardous materials handler. Do not mix this battery with the solid waste stream. Contact your Intermec Technologies Service Center for recycling or disposal information. Li-ion Li-ion Ce produit contient ou utilise une pile principale au lithium-ion (Li-ion). Lorsque la batterie atteint la fin de sa durée de vie utile, la batterie usées doivent être mises aux rebuts par un agent de recyclage ou un manipulateur de matériaux dangereux agréé. Il ne faut pas mélanger la batterie aux autres déchets solides. Pour plus d’informations sur le recyclage ou la mise aux rebuts, contacter votre centre de services Intermec Technologies. Note: In the U.S.A., the EPA does not consider spent Li-ion batteries as hazardous waste. Specific Absorption Rate (SAR) Radio Wave Exposure and Specific Absorption Rate (SAR) Information for Model CK31 Configurations with 802.11b/g Radio The FCC permits a maximum SAR value of 1.6 W/kg. For body worn operation, the highest SAR value for the Model CK31, as tested by Celltech Labs Inc., is 1.16 W/kg. This product has been tested and meets the FCC RF exposure guidelines when used with the Intermec accessories supplied or designated for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Laser Compliance and Precaution The CK31 is registered with the CDRH as a Class II Laser Product (21 CFR Subchapter J, Part 1040). This product has a maximum output of 1 mW at 630-680 nm. Caution: There are no user serviceable parts inside the CK31. Use of controls or adjustments, or performance of procedures other than those specified herein, may result in hazardous laser light exposure of up to 1 mW at 630-680 nm. Attention: La CK31 ne contiennent pas de pièces révisibles par l’utilisateur. L’utilisation de contrôles ou d’ajustements ou l’exécution de procédures autres que celles spécifiées ici peuvent mener à l’exposition à de la lumière laser hasardeuse de plus de 1 mW à 630-680 nm. Note: There are no controls or adjustments provided for routine operation or maintenance of the CK31. AVOID EXPOSURE Laser light is emitted from this aperture. EVITER TOUTE EXPOSITION Lumière laser émis par cette ouverture. CAUTION ATTENTION LASER LIGHT - DO NOT STARE INTO BEAM LUMIERE LASER - NE PAS REGARDER DANS LE FAISCEAU. 630-680 nm 1.0mW CLASS II LASER PRODUCT 630-680 nm 1.0 mW PRODUIT LASER CLASSE II ATTENTION- CAUTION Laser light when open. Do not stare into beam. Lumière laser lors de l'ouverture ne pas regarder fixement dans le faisceau. Complies with U.S.A. 21CFR subchapter J Part 1040 For Users Outside of the United States or Canada Caution: This marking indicates that the user should read all included documentation before use. Battery Information Caution: The battery pack used in this device may ignite, create a chemical burn hazard, explode, or release toxic materials if mistreated. Do not incinerate, disassemble, or heat above 100°C (212°F). Charge only with Intermec Models AC1, AC2, AC3, AD1, and AD2. Do not short circuit; may cause burns. Keep away from children. Use only Intermec battery pack Model AB1G. Risk of fire or explosion if incorrect battery pack is used. Promptly dispose of used battery pack according to the instructions. Battery Recycling Information Li-ion Li-ion This product contains or uses a lithium ion (Li-ion) main battery. When the battery reaches the end of its useful life, the spent battery should be disposed of by a qualified recycler or hazardous materials handler. Do not mix this battery with the solid waste stream. Contact your Intermec Technologies Service Center for recycling or disposal information. Laser and Imager Compliance and Precaution This product complies with the following standards for laser and LED safety: • IEC 60825-1 / EN 60825-1 - Class 2 (1 mW, 630-680 nm) • IEC 60825-1 / EN 60825-1 - Class 1 LED Product (imaging options only, no laser label) This product is provided with a set of laser safety labels illustrated on page 6 of this guide. If the appropriate label is not installed on the device, locate the sheet of labels that was shipped with your device and place the appropriate label over the existing label. Note: Products using the imaging options do not come with the labels mentioned above. These labels are only required for products using laser scan engines. 䄺ਞ˖䆹ᷛᖫ㸼ᯢ⫼᠋Փ⫼ࠡᑨ䯙䇏᠔᳝䱣䰘᭛ḷDŽ 电池信息 警告：该装置中所使用的电池包可能着火、造成化学燃烧危险、爆炸，而且如果处理不当会释放有毒物质。 请勿烧毁、分解 电池，或者加热到 100 鸆 C (212 鸉 F) 以上。 请仅使用型号为 AC1、AC2、AC3、AD1 和 AD2 的 Intermec 充电器。请勿使 电池短路，以免引起火灾。 请不要让儿童接触到电池。 仅供使用的 Intermec 电池包型号是 AB1G。使用电池包错误可能引起火灾或爆炸。请根据说明及时处理用过的电池包。 电池循环利用 ᴀѻકࣙՓ⫼䫖⾏ᄤ /LLRQ Џ⬉∴DŽ Li-ion Li-ion 激光器和投影机兼容性与注意事项 ҙ᳝៤ڣ䗝ӊˈ≵᳝▔ܝᠧॄᷛㅒDŽ Für Benutzer außerhalb von Kanada oder den Vereinigten Staaten Vorsicht: Diese Kennzeichnung weist darauf hin, dass der Benutzer vor dem Gebrauch alle mitgelieferten Unterlagen lesen soll. Akku-Informationen Vorsicht: Der in diesem Gerät verwendete Akkusatz kann sich bei Missbrauch entzünden, chemische Verätzungen verursachen, expoldieren oder toxische Substanzen freisetzen. Nicht verbrennen, zerlegen oder über 100 °C (212 °F) erwärmen. Nur mit Intermec Ladegerät-Modellen AC1, AC2, AC3, AD1 und AD2 laden. Keinen Kurzschluss verursachen; Verbrennungsgefahr. Von Kindern fern halten. Nur Intermec Akkusatz-Modell AB1G verwenden. Wenn ein falscher Akkusatz verwendet wird, besteht Brand- oder Explosionsgefahr. Den verbrauchten Akkusatz sofort gemäß Anweisungen entsorgen. Informationen zum Recycling von Batterien Li-ion Li-ion Dieses Produkt enthält oder verwendet einen Lithiumionen-Hauptakku. Wenn die Batterie ausgedient hat, sollte sie durch einen qualifizierten Recycler oder durch den Sondermüll entsorgt werden. Werfen Sie die Batterie nicht in den Abfall. Setzen Sie sich mit Ihrem Intermec Technologies Service-Zentrum in Verbindung, um weitere Informationen zum Recycling oder Entsorgen zu erhalten. Laser- und Imager-Konformität und Vorsichtsvorkehrungen Dieses Produkt entspricht den folgenden Laser- und LED-Sicherheitsnormen: • IEC 60825-1 / EN 60825-1 - Klasse 2 (1 mW, 630-680 nm) • IEC 60825-1 / EN 60825-1 - Klasse 1 LED-Produkt (Nur Imaging-Optionen, kein Laser-Etikett) Dieses Produkt ist mit einer Reihe von Lasersicherheitsaufklebern ausgestattet, die auf Seite 6 dieser Anleitung abgebildet sind. Wenn das Gerät nicht mit dem richtigen Aufkleber versehen ist, nehmen Sie das Aufkleberblatt, das mit dem Gerät ausgeliefert wurde, und kleben Sie den richtigen Aufkleber über den bereits angebrachten. Anmerkung: Produkte, die den Imaging-Optionen verwenden, werden nicht mit den oben genannten Beschriftungen geliefert. Diese Beschriftungen sind nur für Produkte erfoderlich, die Laserscanner verwenden. 미국 및 캐나다 이외의 거주자의 경우 주의 : 이 표시는 제품 사용 전에 모든 설명서 내용을 읽어야 한다는 것을 나타냅니다 . 배터리 정보 주의 : 이 장치에 사용된 배터리 팩은 잘못 다룰 경우 불이 붙거나 화학 반응을 일으키거나 폭발하거나 또는 유독 물질이 흘 러나올 수 있습니다 . 배터리를 불에 태우거나 분해하거나 100°C (212°F) 이상의 열을 가하지 마십시오 . Intermec AC1, AC2, AC3, AD1 및 AD2 모델만 사용하십시오 . 배터리를 단락시키지 마십시오 . 화재가 발생할 수 있습니다 . 어린이 손이 닿 지 않는 곳에 보관하십시오 . Intermec 배터리 팩 AB1G 모델만 사용하십시오 . 그 외 배터리 팩을 사용할 경우 화재나 폭발 위험이 있습니다 . 다 쓴 배터 리 팩은 지침에 따라 올바르게 폐기하십시오 배터리 재활용 정보 이 제품은 리튬 이온 배터리를 내장 또는 사용하고 있습니다 . 배터리의 수명이 다한 경우 , 다 쓴 배터리는 반드시 공 인된 폐기 업체나 위험 물질 처리 작업장을 통해 안전하게 폐기하십시오 . 이 배터리는 다른 쓰레기와 함께 처리할 수 없습니다 . 재활용이나 폐기에 대한 기타 자세한 사항은 Intermec 기술 서비스 센터에 문의하십시오 . Li-ion Li-ion 레이저 및 이미지 프로그램 준수 유의사항 이 제품은 레이저 및 안전에 대한 다음 표준을 준수합니다 . • • IEC 60825-1 / EN 60825-1 - Class 2 (1 mW, 630-680 nm) IEC 60825-1 / EN 60825-1 - Class 1 LED Product ( 이미지 옵션만 , 레이저 레벨은 아님 ) 이 제품에는 본 설명서 6 페이지에 설명된 일련의 레이저 안전 레이블이 부착되어 있습니다 . 장치에 해당 레이블이 부착되지 않은 경우 장치와 함께 제공된 레이블 시트를 찾아 기존 레이블 위에 해당 레이블을 붙이십시오 . 참고 : 이미징 옵션을 사용한 제품의 경우 위에서 언급한 레이블이 제공되지 않습니다 . 이 레이블은 레이저 스캔 엔진을 사용한 제품에 만 필요합니다 . Para usuários fora do Canadá ou dos Estados Unidos Cuidado: Esta identificação indica que o usuário deve ler toda a documentação fornecida antes do uso. Informações sobre a bateria Cuidado: A bateria utilizada neste dispositivo pode pegar fogo, criar risco de queimadura química, explodir ou exalar materiais tóxicos se abusada. Não incinerar, desmontar nem aquecer a bateria a mais de 100°C (212°F). Carregar apenas com os modelos de carregadores da Intermec AC1, AC2, AC3, AD1 e AD2. Não provocar curto-circuito, pois pode causar queimaduras. Manter afastada de crianças. Apenas a bateria da Intermec modelo AB1G. O uso de uma bateria incorreta pode gerar risco de incêndio ou explosão. Descartar imediatamente as baterias usadas segundo as instruções fornecidas. Infomações de Reciclagem de Bateria Li-ion Li-ion Este produto contém ou usa uma bateria principal de íon de lítio (Li-ion). Quando a bateria chega ao fim da sua vida útil, deve ser descartada por um profissional de reciclagem qualificado ou por um especialista no manuseio de materiais perigosos. Não misture a bateria com fluxo de lixo sólido. Entre em contato com seu Centro de Serviços de Tecnologia Intermec para informações de reciclagem ou descarte. Normas e precauções para dispositivo laser ou de captura de imagens Este produto está de acordo com os seguintes padrões de segurança laser e LED: • IEC 60825-1 / EN 60825-1 - Classe 2 (1 mW, 630-680 nm) • IEC 60825-1 / EN 60825-1 - Produto LED Classe 1 (apenas para opções de processamento de imagem, nenhuma etiqueta de laser) Este dispositivo possui um conjunto de etiquetas de segurança de laser ilustrada na página 6 deste guia. Se a etiqueta apropriada não estiver instalada no dispositivo, localize a folha de etiquetas que foi incluída com seu dispositivo e coloque a etiqueta apropriada sobre a etiqueta existente. Nota: Produtos que usem opções de processamento de imagem não trazem as etiquetas citadas acima. Estas etiquetas são necessárias apenas para produtos que usem máquinas de varredura a laser. Para todas as configurações do CK31, salvo as com o mecanismo de leitura EX25: 0554-05-0569 Para configurações do CK31 com o mecanismo de leitura EX25. 0122-09-0569 Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. Для пользователей вне Соединенных Штатов или Канады Осторожно: Эта пометка означает, что пользователь должен прочитать всю прилагаемую документацию, прежде чем начинать работу. Информация по батареек Осторожно: При неправильном обращении батарейный источник питания, используемый в этом устройстве, может воспламениться, создать опасность химического ожога, взорваться или выделять ядовитые материалы. Не сжигайте, не разбирайте, не допускайте нагрева выше 100°C (212 °F). Для зарядки используйте только устройства Intermec моделей AC1, AC2, AC3, AD1 и AD2. Не замыкайте контакты накоротко – это может причинить ожог. Прячьте от детей. Используйте только батарейный источник питания Intermec модели AB1G. Использование неподходящего батарейного источника питания сопряжено с опасностью возгорания или взрыва. Незамедлительно ликвидируйте использованный батарейный источник питания в соответствии с инструкциями. Информация по утилизации батареек Li-ion Li-ion В данном изделии содержится или используется литиево-ионная (Li-ion) батарейка. Ликвидацию использованной батарейки, исчерпавшей свой ресурс, должно осуществлять специализированное предприятие по утилизации или обращению с опасными материалами. Эта батарейка ни в коем случае не должна попасть в обычные твердые отходы. По вопросам утилизации или ликвидации обращайтесь в соответствующий сервис-центр компании Intermec Technologies. Соответствие требованиям безопасности для лазеров и линейных формирователей изображения Данный продукт соответствует следующим стандартам безопасности лазеров и светоизлучающих диодов (СИД): • IEC 60825-1 / EN 60825-1, класс 2 (1 мВт, 630-680 нм) • IEC 60825-1 / EN 60825-1, СИД класса 1 (только изображения, без лазерных наклеек) Данный продукт снабжен набором предупреждающих табличек по безопасности лазерных устройств (см. стр. 6 настоящего руководства). Если надлежащая наклейка на устройстве отсутствует, найдите лист наклеек, который входит в комплект поставки, и поместите нужную наклейку поверх существующей. Примечание: Изделия, использующие формирование изображения, не снабжаются указанными наклейками. Эти наклейки требуются только для изделий, использующих лазерные сканирующие устройства. Para usuarios fuera de Canada o de los Estados Unidos Precaución: Esta marca indica que el usuario debe leer toda la documentación incluida antes del uso. Información de la batería Precaución: La batería que se usa en este dispositivo puede encenderse, crear un peligro de quemadura química, explotar o expedir materiales tóxicos si se trata indebidamente. No la incinere, desarme ni caliente sobre 100°C (212°F). Cárguela sólo con los modelos Intermec AC1, AC2, AC3, AD1 y AD2. No haga cortocircuitos porque pueden causar quemaduras. Manténgala alejada de los niños. Use sólo la batería Intermec modelo AB1G. El uso de la batería incorrecta puede presentar peligro de incendio o de explosión. Descarte rápidamente la batería usada según las instrucciones. Información acerca del reciclaje de la batería Li-ion Este producto contiene o usa una batería principal de iones de litio (Li-ion). Cuando la batería llega al final de su vida útil, debe ser desechada por personal especializado en reciclaje de materiales o manejo de materiales peligrosos. No mezcle la batería con otros residuos sólidos. Pónganse en contacto con su Centro de servicio de Intermec Technologies para obtener información sobre reciclaje o desecho de materiales. Li-ion Acatamiento y precaución de láser y del dispositivo de imágenes Este producto cumple con los siguientes estándares para seguridad de láser y diodos LED: • IEC 60825-1 / EN 60825-1 - Class 2 (1 mW, 630-680 nm) • IEC 60825-1 / EN 60825-1 - Class 1 Producto LED (sólo opciones de imágenes, sin etiqueta láser) Con el producto se incluye una serie de etiquetas de precaución sobre el uso del láser como las que se ilustran en la página 6 de esta guía. Si el dispositivo no muestra la etiqueta correcta, busque la hoja de etiquetas enviadas con el dispositivo y pegue la etiqueta correspondiente sobre la existente. Note: Los productos que utilizan las opciones de imágenes no contienen las etiquetas mencionadas anteriormente. Estas etiquetas sólo son requeridas para productos que utilizan los motores de lectura láser. CK31 Class 2 Laser Labels ENGLISH GERMAN SIMPLIFIED CHINESE (DEUTSCH) IEC 60825-1:1993, + A1: 1997, + A2: 2001. EN 60825-1:1994, + A1: 2002, + A2: 2001. CAUTION CLASS 2 LASER LIGHT WHEN OPEN. DO NOT STARE INTO BEAM. LASER LIGHT DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT 1mW 630 - 680nm IEC 60825-1:1993, + A1: 1997, + A2: 2001. EN 60825-1:1994, + A1: 2002, + A2: 2001. VORSICHT IEC 60825-1:1993, + A1: 1997, + A2: 2001. LASERLICHT, WENN ABDECKUNG GEÖFFNET. NICHT IN DEN STRAHL BLICKEN. LASERLICHT NICHT IN DEN STRAHL BLICKEN LASER KLASSE 2 1mW 630 - 680nm 1mW 630 - 680nm FRENCH ITALIAN (ESPAÑOL) (FRANÇAIS) (ITALIANO) ¡CUIDADO! CATEGORIA 2 LUZ LASER AL ABRIR. ¡NO MIRE HACIA EL RAYO! LUZ LASER ¡NO MIRE HACIA EL RAYO! CATEGORIA 2 PRODUCTO LASER 1mW 630 - 680nm JAPANESE IEC 60825-1:1993, + A1: 1997, + A2: 2001. IEC 60825-1:1993, + A1: 1997, + A2: 2001. KLASSE 2 SPANISH CEI 60825-1:1993, + A1: 1997, + A2: 2001. EN 60825-1:1994, + A1: 2002, + A2: 2001. RUSSIAN CEI 60825-1:1993, + A1: 1997, + A2: 2001. EN 60825-1:1994, + A1: 2002, + A2: 2001. ATTENTION CLASSE 2 LUMIERE LASER EN CAS D' OUVERTURE. NE PAS REGARDER DANS LE FAISCEAU. LUMIERE LASER NE PAS REGARDER DANS LE FAISCEAU APPAREIL Á RAYONNEMENT LASER DE CLASSE 2 1mW 630 - 680nm 1mW 630 - 680nm NORWEGIAN - DANISH (NORSKA - DENSK) CEI 60825-1:1993, + A1: 1997, + A2: 2001. EN 60825-1:1994, + A1: 2002, + A2: 2001. ATTENZIONE CLASSE 2 IEC 60825-1:1993, + A1: 1997, + A2: 2001. EN 60825-1:1994, + A1: 2002, + A2: 2001. ADVARSEL KLASSE 2 LASERSTRÅLING NÅR DEKSEL ÅPNES. STIRR IKKE INN I STRÅLEN. LUCE LASER IN CASO DI APERTURA. NON FISSARE IL FASCIO. LUCE LASER NON FISSARE IL FASCIO LASERSTRÅLING STIRR IKKE INN I STRÅLEN APPARECCHIO LASER DI CLASSE 2 KLASSE 2 LASER PRODUKT 1mW 630 - 680nm 1mW 630 - 680nm FINNISH SWEDISH (SUOMI) (SVENSKA) (PORTUGUÊS) IEC 60825-1:1993, + A1: 1997, + A2: 2001. EN 60825-1:1994, + A1: 2002, + A2: 2001. IEC 60825-1:1993, + A1: 1997, + A2: 2001. EN 60825-1:1994, + A1: 2002, + A2: 2001. CEI 60825-1:1993, + A1: 1997, + A2: 2001. EN 60825-1:1994, + A1: 2002, + A2: 2001. VAROIAVATTAESSA VARNING LUOKAN 2 VAARA LASERSÄTEILYÄ ÄLÄ TUIJOTA SÄTEESEEN VARNING LASERSTRÅLNING STIRRA INTE IN I STRÅLEN LUOKAN 2 LASER LAITE LASER KLASS 2 630 - 680nm ATENÇÃO KLASS 2 1mW 630 - 680nm CLASSE 2 LUZ DE LASER QUANDO ABERTO. NÃO OLHAR NA DIRECÇÃO DO FEIXE. LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD. STIRRA EJ IN I STRÅLEN. OLET ALTTIINA LASERSÄTEILYLLE. ÄLÄ TUIJOTA SÄTEESEEN. 1mW PORTUGESE LUZ DE LASER NÃO OLHAR NA DIRECÇÃO DO FEIXE EQUIPAMENTO LASER CLASSE 2 1mW 630 - 680nm Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com © 2010 Intermec Technologies Corporation. All rights reserved. Model CK31 Compliance Insert *075206-009* P/N 075206-009, Revision I
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : mfisher Create Date : 2006:02:14 15:53:15Z Modify Date : 2010:06:30 15:31:32Z XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Format : application/pdf Creator : mfisher Title : 075206-008.fm Creator Tool : FrameMaker 8.0 Producer : Acrobat Distiller 9.3.2 (Windows) Document ID : uuid:0f5f2821-11cf-44e5-8248-0701ce845fed Instance ID : uuid:243ffe6a-841f-4355-ad44-7022a94aa1d4 Page Mode : UseNone Page Count : 8EXIF Metadata provided by EXIF.tools