Intermec Technologies MC75 MC75 User Manual legal

Download:
Mirror Download [FCC.gov]
Document ID	730133
Application ID	pPUDp6X5ByoDLXhL45GdhQ==
Document Description	Final Users Manual part 2 of 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	166.57kB (2082097 bits)
Date Submitted	2006-11-20 00:00:00
Date Available	2006-06-02 00:00:00
Creation Date	2006-07-05 08:29:41
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2006-07-05 08:29:50
Document Title	legal
Document Creator	PScript5.dll Version 5.2
Document Author:	ThingA

Chapter 4 — Network Support
Properties
Select a COM Port from the Choose COM Port box to register for this
device, then check Enable Wireless Printing to complete the COM port
registration. To change your COM port selection, clear (uncheck) the Enable Wireless Printing box, select a new COM port, then check Enable
Wireless Printing again. Choose COM Port items already in use are
grayed out.
When you enable Wireless Printing, a status message is shown near the
bottom of the screen to confirm your action. To print a test page to your
printer, tap Print Test Page.
Check Default to set this printer to identify the assigned COM Port as the
WPPort in the registry. See the Bluetooth Resource Kit User’s Guide for
more details on WPPort.
Tap ok to return to the Wireless Printing page.
700 Series Color Mobile Computer User’s Manual
101
Chapter 4 — Network Support
File Transfer
Use this page to enable your unit to receive files from another Bluetooth
device, or from any device that supports this function.
This does not apply to the 730 Computer. From this point, this transfer is
similar to an IrDA file transfer. Tap Start > Programs > File Explorer, tap
to hold the file to transfer, then select Beam File from its pop-up menu.
The system searches for a list of Bluetooth devices that will accept a connection from your unit. When the list is complete, tap on a device to
which to send the file. Note: in some cases, the user of the target device has to
“accept” the file before it is transmitted.
102
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
Connecting with Bluetooth
Note: While these instructions apply to many Bluetooth devices, these instructions use the Nokia 3650 for example purposes.
Before you connect to the network, make sure Bluetooth is enabled on
your 700 Color Computer before discovering and connecting to remote
devices.
Tap Start > Settings > the Connections tab > the Bluetooth icon. Tap On
to activate Bluetooth, then tap ok to exit the applet.
Also make sure Bluetooth is enabled on your mobile phone. For example,
with the Nokia 3650, go to its menu, select Connect > Bluetooth, then set
My phone’s visibility to “Shown to all.”
Do the following to establish a Bluetooth connection between your 700
Color Computer and your mobile phone, then establishing a dial-up networking session with your wireless network. Once connected, you should
be able to browse Internet websites and use other online resources from
your 700 Color Computer.
To view additional information for any screen in the wizard or while
changing settings, tap the Help icon.
1 Tap Start > Settings > the Connections tab > the Connections icon. In
My ISP, tap Add a new modem connection.
700 Series Color Mobile Computer User’s Manual
103
Chapter 4 — Network Support
2 Enter a name for the connection, such as “Nokia.” In the Select a modem list, select “Bluetooth,” then tap Next to continue.
3 Tap New... if the phone is not listed in the known devices. Make sure
your Bluetooth device is turned on before you start the search.
104
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
4 When the discovery of devices is complete, select your Bluetooth device,
then tap Next to continue.
5 Enter the correct Device PIN on both the Bluetooth device and the 700
Color Computer, then tap Next to continue.
700 Series Color Mobile Computer User’s Manual
105
Chapter 4 — Network Support
6 Enter a name for the device if needed, then tap Finish.
7 After bonding completes, select your Bluetooth device from the list of
bonded devices, then tap Next.
106
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
8 Enter the appropriate number as it should be dialed for your Bluetooth
connection, then tap Next to continue. Enter the user name, password,
and domain required for your Bluetooth device, then tap Finish.
Now you can establish a connection to your network via the Internet Explorer application. To disconnect, tap the Connectivity icon in the top
menu bar, then select Disconnect.
Local Area Networks
See the Developer’s Support web site for the latest information on network
adapters for your unit.
The 700 Color Computer is a versatile mobile computer that easily adds to
your wired or wireless data collection network. You can connect your 700
Color Computer to your network using either USB communications or
802.11b or 802.11b/g radio communications.
Configuring USB Communications
You can place the 700 Color Computer in a single dock, multidock, modem dock, or vehicle dock to transfer data to and receive data from another device using USB communications. The USB cable, single dock, multidock, modem dock, and vehicle dock are sold separately. For information
on accessories and how to order them, see “Accessories” on page 21.
To use USB communications with your 700 Color Computer
1 Connect the dock to the USB port of the other device using an appropriate USB cable.
2 Make sure your USB device is configured for USB communications.
3 Insert the 700 Color Computer into the dock.
4 Turn on the 700 Color Computer.
700 Series Color Mobile Computer User’s Manual
107
Chapter 4 — Network Support
Configuring 802.11 Radio Communications
Caution: Make sure all components with antennas are at least 30 cm (1
ft) apart when power is applied. Failure to comply could result in
equipment damage.
The wireless 700 Color Computer has an internal 802.11b or 802.11b/g
radio to transfer data using wireless communications. This manual assumes
you already have set up your wireless communications network, including
your access points. If you are using a UDP Plus network, have your
Intermec Application Server communicate with a host computer. Your
700 Color Computer supports TCP/IP and UDP Plus.
Configuring the Network Parameters for a TCP/IP Network
In a TCP/IP network, the 700 Color Computer communicates with a host
computer directly using TCP/IP. The access point acts as a bridge to allow
communications between the wired and wireless networks.
1 Configure the infrastructure mode, network name (SSID), host IP address, and IP settings (if not using DHCP) on each 700 Color Computer in the network.
2 Configure security. Tap Start > Settings > the System tab > the Wireless Network icon to access the Profile Wizard for the 802.11b or
802.11b/g radio module. Go to Appendix A, “Configurable Settings,”
for information.
Configuring the Network Parameters for a UDP Plus Network
In a UDP Plus network, the 700 Color Computer communicates with a
host computer through the Intermec Application Server. The Intermec
Application Server translates UDP Plus packets on the wireless network
into TCP/IP packets on the wired network and vice versa. The access
point acts as a bridge to allow communications between the wired and
wireless networks.
1 Configure the network name (SSID), controller IP address, and IP settings (if not using DHCP), and controller port (set to 5555) on each
700 Color Computer in the network.
2 Configure security. Tap Start > Settings > the System tab > the Wireless Network icon to access the Profile Wizard for the 802.11b or
802.11b/g radio module. Go to Appendix A, “Configurable Settings,”
for information.
The easiest way to configure the network parameters on the 700 Color
Computer is to use the Intermec Settings applet. Go to Appendix A,
“Configurable Settings.” for information.
Network Adapters
The 700 Color Computer can have up to three radios installed. The default network adapter or radio is dependent on what radios are installed in
your unit. The 700 Color Computer is capable of supporting 802.11i security requirements.
108
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
With the NDISTRAY pop-up menu (the Network Driver Interface Specification tray application) from the System Tray, you can specify “802.11,”
“Ethernet,” or “No Networking” to load onto your 700 Color Computer
when a cold-boot is performed. When a warm boot is performed, the 700
Color Computer loads the network set just prior to the warm boot.
The 730 Computer only has the 802.11b radio and Bluetooth. It does not
have an external antenna. Other radios are not supported.
Ethernet Communications (740, 741, 750, 751, 760, 761 Computers)
Follow the steps below to start Ethernet communications on the 700 Color
Computer. If your system does not contain an 802.11b or 802.11b/g
radio, then Ethernet networking using DHCP is selected as the default.
When “Built-in Ethernet” is selected from the NDISTRAY pop-up menu,
then the Ethernet icon shown to the left appears in the System Tray as
circled in the following illustration.
700 Series Color Mobile Computer User’s Manual
109
Chapter 4 — Network Support
Wireless 802.11 Communications
When “Wireless 802.11” is selected via the NDISTRAY pop-up menu,
the Wireless 802.11 antenna icon shown to the left appears in the system
tray as circled in the following illustration.
No Networking
When “No networking” is selected from the NDISTRAY pop-up menu,
the disconnected icon shown to the left appears in the system tray as
circled in the following illustration.
Network Selection APIs
The Network Selection APIs change the network adapter configuration
programmatically. Both drivers support the same IOCTL function numbers for loading and unloading the drivers. Go to Chapter 7, “Programming,” to see the APIs.
110
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
Network Connections
From the 700 Color Computer, tap Start > Settings > the Connections
tab > the Connections icon > the Advanced tab > Network Card or the
Network Adapters tab to access the network connections for this unit.
Make the changes necessary for your network, then tap ok when finished.
Creating a Wireless Network Connection
Use the Wireless Network applet for more security choices and better
roaming behavior. See Appendix A for information.
Networks already configured are preferred networks and are listed in
Wireless networks. You can connect to only preferred networks or search
for and connect to any available network.
A wireless network can be added either when the network is detected, or
manually by entering settings information. To determine if authentication
information is needed, see your network administrator.
1 Tap Start > Settings > the Connections tab > the Connections icon.
700 Series Color Mobile Computer User’s Manual
111
Chapter 4 — Network Support
2 Tap the Advanced tab > Network Card > the Wireless tab > Add New .
3 Tap the General tab, then enter a network name. If the network was
detected, the network name is entered and cannot be changed.
From Connects to, select to what your network is to connect. If you
select “Work,” you can do a vpn connection or use proxy servers. If you
select “The Internet,” you can connect directly to the internet.
To connect to an ad-hoc connection, select This is a device-to-device
(ad-hoc) connection.
4 Tap the Network Key tab, then do the following:
To Disable Authentication
a Set Authentication to either “Open” if WEP keys are not required;
or “Shared” when WEP keys are required for association.
112
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
b Set Data Encryption to “Disabled.”
To Enable WEP Encryption
a Set Authentication to either “Open” if WEP keys are not required;
or “Shared” when WEP keys are required for association.
b Set Data Encryption to “WEP.”
c To change the network key, clear The Key is provided for me automatically box, then enter the new Network key and select the appropriate Key index.
Note: The following information applies when you have Enable Microsoft’s Wireless Zero Config checked via the Wireless Network applet (see
Appendix A, “Configurable Settings”).
700 Series Color Mobile Computer User’s Manual
113
Chapter 4 — Network Support
To Enable WPA Authentication (730, 751, 751, 761 Computers)
a Set Authentication to “WPA” (see page 236).
b Set Data Encryption to either “WEP” or “TKIP” (see page 236).
To Enable WPA Authentication Using a Preshared Key (730, 741, 751, 761 Computers)
a Set Authentication to “WPA-PSK” (see page 236).
b Set Data Encryption to either “WEP” or “TKIP” (see page 236).
c Enter the new Network key.
114
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
5 Tap the 802.1x tab, select either “PEAP” or “Smart Card or Certificate”
for the EAP type, then tap Properties to adjust its settings.
6 Tap ok to return to the Configure Wireless Network screen.
7 From the Networks to access drop-down list, select “All Available,”
“Only access points,” or “Only computer-to-computer” depending on
the type of networks to which you connect.
To connect only to networks you have already configured, clear Automatically connect to non-preferred networks. Tap ok to close this
screen.
Note: If you select to automatically connect to non-preferred networks,
your device detects any new networks and provide you the opportunity to
configure them.
700 Series Color Mobile Computer User’s Manual
115
Chapter 4 — Network Support
AutoIP/DHCP
Automatic Private IP Addressing (AutoIP) is enabled by default in
Windows Mobile 2003. To remain compatible with other versions of
Pocket PC, this setting needs to be enabled. You can configure the registry
settings in the following to set the required AutoIP/DHCP behavior:
S For Ethernet:
HKEY_LOCAL_MACHINE\Comm\LAN9001\TcpIp
S Fot 802.11:
HKEY_LOCAL_MACHINE\Comm\NETWLAN1\TcpIp
Other registry keys that can modify the behavior of AutoIP are as follows.
You can find the appropriate settings and behavior of each of these keys in
Microsoft Help.
S AutoInterval
S AutoMask
S AutoSubnet
S AutoIP
S AutoSeed
When a TCP/IP client cannot find a DHCP server, it generates an AutoIP
address from the 169.254.xxx.xxx block. The client then tries to check for
a DHCP server every 15 seconds and if a DHCP server is found, the client
drops the AutoIP address and uses the address from the DHCP server.
In the MSDN Windows CE documentation available out on the Microsoft Developer Network web site (www.msdn.com), see “Automatic Client
Configuration” for more information on AutoIP.
To disable AutoIP, set the AutoCfg registry entry to “0.” If a DHCP server cannot be found, instead of using AutoIP, the system will display the
“Unable to obtain a server assigned IP address” message.
Note: If you try to disable AutoIP using a CAB file to set the registry value
for AutoIP, remember to set the EnableDHCP value to “1” to keep
DHCP enabled
Note: To extend the number of attempts that a DHCP client makes to get
a DHCP address, use the DhcpRetryDialogue and DhcpMaxRetry registry
settings.
Note: Change the AutoInterval registry key value to make the client retry
more often to obtain a DHCP address.
Wide Area Networks
The 700 Color Computer does not support wide area networks.
Phone Applications
The following phone applications apply to certain configurations. See the
chart on page 98 to learn which applies to your 700 Color Computer.
116
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
Microsoft Phone Application (761 Computers with CDMA Radios)
With the WAN radio module installed in your 761 Computer, you can
send and receive telephone calls. Use the speaker on the back of the computer as your earpiece and use the connector on the bottom of the computer for your mouthpiece.
Data Provisioning (Sprint)
Note: If you wish to do this activation another time, tap Cancel to close
this wizard, then tap Yes.
It is necessary to initiate activation before using your Microsoft Phone application. Below are the instructions:
1 Tap Start > Programs > the Phone desktop icon or tap Start > Phone
from the Today screen to access the application which processes your
phone calls. Tap the Close button in the upper right corner of this application to close.
2 From the Phone application, tap Tools > Activation Wizard.
3 Have your activation code, phone number (MDN), and MSID information ready before you tap Next to continue. You can get this information from your network provider.
700 Series Color Mobile Computer User’s Manual
117
Chapter 4 — Network Support
4 Enter your 6-digit activation code, then tap Next to continue.
5 Enter the phone number and MSID from Sprint, tap Next to continue.
6 The application prompts whether the information entered is correct. If
so, tap Yes to continue, else tap No to return to the previous screen.
118
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
7 Note that voice service is available immediately. Data service take a
minimum of four hours of activation before you can use the service. If
after four hours, a data connection is not established, see “Data Provisioning” on page 117 to manually launch data provisioning.
The application acknowledges that your phone will be in service in four
hours. Tap Finish to close the wizard.
Data Provisioning (Verizon)
Note: If you wish to do this activation another time, tap Cancel to close
this wizard, then tap Yes.
It is necessary to initiate activation before using your Microsoft Phone application. Below are the instructions:
1 Tap Start > Programs > the Phone desktop icon or tap Start > Phone
from the Today screen to access the application which processes your
phone calls. Tap the Close button in the upper right corner of this application to close.
2 From the Phone application, tap Tools > Activation Wizard.
700 Series Color Mobile Computer User’s Manual
119
Chapter 4 — Network Support
3 Tap Auto to initiate the activation.
4 The application acknowledges that your phone is now in service. Tap
Finish to close the wizard.
Phone Application
Note: Wait at least four hours after Sprint activation is complete before
using this application. Data provisioning should occur automatically. Network information about your 761 Computer needs to propagate through
the Sprint Network after the activation is complete.
If data provisioning does not occur automatically, tap Start > Settings >
the Personal tab > the Phone icon. Tap the Data tab, then tap Provision
to initiate a session.
120
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
Tap the appropriate keys to enter a telephone number, then tap Talk to
dial the number. Tap End to “hang up” the phone.
Tap this to backspace one digit.
Tap this to dial the phone number
shown above the keypad.
Tap this to select a previously
dialed number.
Tap this to view your previous calls.
Tap this to “hang up” your current
call.
Tap this toggle the mute option.
Tap this to access the Contacts application.
Tap this to access the Notes application.
Speed Dial
Tap Speed Dial to select a telephone number with which the 761 Computer is to dial automatically. To add to this list, use the Contacts application. See Chapter 2, “Windows Mobile 2003,” for more information
about the Contacts application.
700 Series Color Mobile Computer User’s Manual
121
Chapter 4 — Network Support
Call History
Tap Call History to note the telephone numbers that were previously
dialed from this 761 Computer.
Tools
Use the Tools menu to send a voice mail, access the Activation Wizard,
send an SMS email message, or configure phone settings.
S Tap Tools > Voice Mail to call and leave a voice message.
S Tap Tools > Activation Wizard to access the wizard with which to activate your 761 Computer. Be sure to have an activation code, a phone
number, and MSID information ready. See page 117 for instructions on
using this wizard.
Sprint Networks
122
Verizon Networks
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
S Tap Tools > Send SMS tab to access the Inbox application and send an
SMS (Short Messaging Service) message. Be sure to have an SMS number ready to send the message — this is usually the mobile phone number. See Chapter 2, “Windows Mobile 2003,” for Inbox information.
Phone Settings
Either select Tools > Options from the Phone application or select Start >
Settings > the Personal tab > the Phone icon to access the applet.
S Tap the Phone tab to customize your phone settings such as the ring
type and ring tone to use for incoming calls, and the keypad tone to use
when entering phone numbers. Tap Other Settings to go to the Sounds
& Notifications applet. Select Start > Help for more information.
700 Series Color Mobile Computer User’s Manual
123
Chapter 4 — Network Support
S Tap the Location tab to toggle between your location being visible for
everyone to detect and hiding your location from everyone except 911.
Sprint Networks
Verizon Networks
S Tap the Data tab to either reset your connection settings for PCS Vision or update your PCS Vision profile.
For Sprint Networks, if your 761 Computer is unable to make a data
connection and it has been more than four hours since activation, you
can launch data provisioning from this screen. Tap Provision, then follow the prompts. It takes a few minutes to set up the data connections.
Note: The data provisioning process can be automatically initiated by
the Sprint network, by attempting to make a cellular line connection to
the WAN before the 761 Computer is data provisioned, or by manually
starting the connections through this screen. Intermec recommends that
Sprint Network “push” the data provisioning to your unit. This should occur shortly after the voice activation is complete.
Sprint Networks
124
Verizon Networks
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
S Tap the System tab to select the applicable function.
Sprint Networks
Verizon Networks
S Tap the Phone Info tab to view the phone settings.
Sprint Networks
Verizon Networks
Microsoft Phone Application (761 Computers with GSM Radios)
With the WAN radio module installed in your 761 Computer, you can
send and receive telephone calls. Use the speaker on the back of the computer as your earpiece and use the connector on the bottom of the computer for your mouthpiece.
Tap Start > Settings > the Phone desktop icon from the Personal tab or
tap Start > Phone from the Today screen to access the application which
processes your phone calls. Tap the Close button in the upper right corner
of this application to close.
700 Series Color Mobile Computer User’s Manual
125
Chapter 4 — Network Support
Activation
The GSM phone is activated via a SIM card that you can purchase from
your network provider.
Phone Application
Tap the appropriate keys to enter a telephone number, then tap Talk to
dial the number.
Tap this to backspace one digit.
Tap this to view your previous calls.
Tap this to select a previously
dialed number.
Tap this to dial the phone number
shown above the keypad.
Tap this toggle the mute option.
Tap this to access the Contacts application.
Tap this to access the Notes application.
Call History
Tap Call History to note the telephone numbers that were previously
dialed from this 761 Computer.
126
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
Speed Dial
Tap Speed Dial to select a telephone number with which the 761 Computer is to dial automatically. To add to this list, use the Contacts application. See Chapter 2, “Windows Mobile 2003,” for more information
about the Contacts application.
Tools
Tap Tools > Send SMS tab to access the Inbox application and send an
SMS (Short Messaging Service) message. Be sure to have an SMS number
ready to send the message — this is usually the mobile phone number. See
Chapter 2, “Windows Mobile 2003,” for information about Inbox.
700 Series Color Mobile Computer User’s Manual
127
Chapter 4 — Network Support
Phone Settings
Either select Tools > Options from the Phone application or select Start >
Settings > the Personal tab > the Phone icon to access the applet.
S Tap the Phone tab to customize your phone settings such as the ring
type and ring tone to use for incoming calls, and the keypad tone to use
when entering phone numbers. Tap Other Settings to go to the Sounds
& Notifications applet.
S Tap the Services tab to access settings for any of the provided services.
128
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
Tap any of the settings, then tap Get Settings. Make your changes, then
tap ok to return to the Settings screen. Below is a sample Settings
screen.
S Tap the Network tab to find, set, or select the type of network on
which this phone is to communicate.
700 Series Color Mobile Computer User’s Manual
129
Chapter 4 — Network Support
Phone Information
To learn the latest phone settings, including the manufacturer, model,
firmware rev, and IMEI, select Start > Settings > the System tab, then tap
the WAN Info desktop icon. Tap ok when finished.
SB555 Watcher (760 Computers with CDMA Radios)
The SB555 Watcher program is used on the 760 Computer with CDMA
radios only. Use this primarily to activate the WAN radio. Once the WAN
radio is activated, you can remove the SB555 Watcher program from the
760 Computer.
This tells you how to set up your CDMA radio in your 760 Computer.
Below are terms to familiarize you with CDMA radio technology:
Note: Set up and provision information is also available in the 700 Color
CDMA Radio Setup Quick Start Guide P/N: 962-054-063.
Activation
The process of programming the radio with the lock code (MSL) and phone number (MIN) to
allow it to communicate on the provider’s network. Once activation is complete you can make
voice calls (if enabled by the carrier) with the mobile computer.
Data Provisioning
The process of activating the ability for the CDMA radio to establish data connections, such as
connecting to the Internet. The CDMA radio makes data connection only after it is activated
and data provisioned.
NID (Network ID) A numeric value programmed into the CDMA radio at the factory or during the activation
process. Your carrier may or may not use this value, but your carrier may provide this for activation purposes.
SID (System ID)
A numeric value programmed into the CDMA radio at the factory or during the activation
process. This number is used by your carrier to determine if the radio belongs to its CDMA
network. Your carrier may provide this number for activation purposes.
Note: Descriptions in this chapter are for Sprint PCS, Bell Mobility, Telus, and Verizon Networks versions of the SB555 Watcher program. Other carriers may be added pending regulatory and carrier approval.
130
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
Copying CDMA Radio Module CAB Files from Intermec Web Site
Copy CAB files from the Intermec web site at www.intermec.com onto
your desktop. Intermec recommends one of two methods with which to
load these CAB files onto your 760 Computer:
S via the Microsoft ActiveSync application
S via a CompactFlash or Secure Digital storage card. See Chapter 3,
“Installing Applications,” for information about these methods.
Via Microsoft ActiveSync
You can transfer files from your desktop to your 760 Computer via Microsoft ActiveSync. See Chapter 2, “Windows Mobile 2003” for more information about ActiveSync.
1 Obtain software from the Intermec web site as described earlier. Download the software to any location on your 760 Computer, such as the
Temp folder via the My Device root location.
2 Tap the carrier CAB file to install the application.
3 Go to “Finishing the Installation” on page 132.
Via a CompactFlash or Secure Digital Storage Card
Note: These instructions are based on default locations. You can change
the location to which to copy your CAB files.
1 Make sure the Registry Restore feature on your 760 Computer is disabled. Select Start > Settings > the System tab. Tap the Utilities desktop icon, the Registry Save tab, then clear the Enable Registry Save box.
2 Copy the CAB files for your carrier to your CompactFlash or Secure
Digital storage card after downloading it from the web site.
3 Cold-boot your 760 Computer. Remove the AB10 battery pack and
press the reset button in the bottom of the battery compartment.
4 Go through the normal getting started steps detailed in your 700 Color
CDMA Radio Setup Quick Start Guide.
700 Series Color Mobile Computer User’s Manual
131
Chapter 4 — Network Support
5 Install the CompactFlash or Secure Digital memory card into the card
slot in your 760 Computer. Note that if you do not want the CAB files
erased after installation, set the CAB file attributes to “read-only” after copying them to the storage card.
6 Tap Start > Programs > the File Explorer icon on the 760 Computer.
7 Tap the pull-down menu for My Documents and tap the My Device
root location.
8 If you are using a CompactFlash storage card,
tap Storage Card.
If you are using an Secure Digital storage card,
tap SDMMC Disk.
9 Scroll down, tap the Sprint Watcher CAB file to install the application.
Finishing the Installation
Do the following to run the SB555 Watcher application. Be sure to do
step 1 as it is important to perform a warm-boot on your 760 Computer.
Upon restart, the Watcher application sets up on the 760 Computer for
activation.
1 Tap Start > Programs > the Watcher icon.
2 Tap Yes, I accept to accept the license agreement, tap OK to continue.
Note this license agreement does not appear again after this installation.
3 Tap OK for the 760 Computer to perform a warm-boot.
132
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
Activation
Note: Set the date and time before doing this activation.
SB555 Watcher is for activation and data provisioning. Once you enable
voice capability, data capability, or both depending on the carrier, remove
this program from the system by cold-booting your computer.
Do not use the SB555 Watcher to make data/voice calls on a daily basis:
S The SB555 Watcher application is a third-party application unaware of
certain power management methods used in your 760 Computer. Therefore,
the application consumes more power than necessary.
S The application size consumes memory better used for application data.
The process of setting up the account with your carrier and enabling the
CDMA WAN radio in your 760 Computer is called activation. To properly function, program the CDMA device with the necessary information
and set up the network carrier account. If either piece has errors, the device does not function on the CDMA network.
The CDMA radio is pre-programmed for a specific carrier, such as Sprint,
Telus, Bell Mobility, Verizon, etc.). Therefore, information about your
radio should already be in your carrier’s database.
You need to notify the carrier and set up mobile accounts for each unit
you are activating. The Electronic Serial Number (ESN hex 63xxxxxx)
that you need to supply to your carrier is located in two places:
S On the outside of the 760 Computer shipping box.
S On the inside of the 760 Computer battery compartment. The label
includes the term “ESN” and a bar code along with the serial number.
The ESN comes in both decimal and hexadecimal formats. Most carriers
accept either format, but with a preference for the decimal format. You
only need to provide one number to your carrier.
S The decimal format consists of 11 digits, beginning with “099.”
S The hexadecimal format is an 8-digit number, beginning with “63.”
Accounts for Verizon and Sprint carriers can be set up for data only. Canadian carriers (Telus and Bell Mobility) can be set for data only, voice only,
or both voice and data. This is determined by your application and the
services your carrier offers.
After the all ESNs are provided to the carrier and the carrier has established the accounts, you will be provided with the lock codes and telephone numbers needed to complete the activation process. You use the
SB555 Watcher program to accomplish this task. Note this for future use.
Note: Ensure that you receive a spreadsheet with your order that calls out
all ESNs in both decimal and hexadecimal formats.
Note: Keep the activation information for your devices in a safe, accessible
place should you have any future issues.
Note: Not all of the elements listed are required by all service providers.
700 Series Color Mobile Computer User’s Manual
133
Chapter 4 — Network Support
ESN of the modem
Lock/Activation Code (may be termed one of the following):
S MSL — Master Subsidy Lock
S OTSL — OneTime Subsidy Lock
S SPC — Service Provisioning Code
S OTKSL — One Time Key Subsidy Lock
SID (System ID)
NID (Network ID)
User Name
Password
MIN
MSD
MDN
Note: The activation process for your Watcher version may vary from the
following steps. Thus, you may not have to do all of them.
1 Tap Start > Programs > the Watcher icon or tap the Watcher icon from
the NDISTRAY via the Today screen (circled in the following illustration) to launch the SB555 Watcher program.
2 The Activation Wizard should start automatically. If not, then tap
Admin > Activation Wizard from the bottom of the screen.
3 Tap Next to move from one screen prompt to the next.
134
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
4 When you reach the Activation screen, select Manual Activation.
5 At the appropriate screen, enter the Activation Code (OTSL, MSL,
OTKSL, or SPC) provided by your carrier and tap Next.
6 Enter the phone number provided when your 760 Computer was activated and tap Next.
Verizon Automated Activation Process
Note: This process takes approximately 60 seconds.
Do the following to activate Verizon on your 760 Computer:
1 Tap Start > Programs > the Watcher icon.
700 Series Color Mobile Computer User’s Manual
135
Chapter 4 — Network Support
2 Tap Yes, I accept to accept the license agreement, tap OK to continue.
Note this license agreement does not appear again after this installation.
3 Select OK to initiate the warm-boot, then after the warm-boot, start the
Watcher program again, select Automated Activation, then click Next.
Note: You must be in the Verizon coverage area to activate your 760
Computer and only in the location of intended use.
4 Click Next, click Next again to dial the number displayed on the screen.
5 The activation process starts automatically.
6 You will see a series of unlock codes on your screen.
7 Click the Connect button to connect to the carrier’s network.
8 Select Start > Internet Explorer, then choose a web site. Your unit is
now successfully activated.
136
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
9 Perform a cold-boot on your 760 Computer to uninstall the Watcher
application, which is intended for activation purposes only. Use the following for establishing and maintaining connection to the WAN radio:
S Custom application using Intermec WWAN Toolkit API
S Custom customer application using Connection Manager Interface
Note: When connecting to the WAN radio via Pocket PC Connection
Manager, use the 10-digit phone number@vzw3g.com for the user
name (such as 1234567890@vzw3g.com) and “vzw” for the password.
Sprint Automated Activation Process
Note: Sprint PCS uses a data provisioning method termed IOTA (Internet
Over The Air) to complete its activation and data enablement. These steps
detail how to properly activate and data provision your 760 Computer.
1 Give Sprint your ESN (either on the box or on a label inside the battery
compartment), rate plan, and account information. The label would include the term “ESN” and a bar code along with the serial number.
2 Sprint provides you with the following for each ESN:
S MDN, such as 214-555-5555
S MSID, such as 214-555-5555
S MSL/OTKSL (Activation Code), such as 945614
S NAI (Network Access Identifier), such as the following:
CustomerName103@sprintpcs.com
Use a Secure Digital storage card with only the Sprint_Watcher_PPC_
2002-03xxx.CAB file in the “\SDMMC\Cabfiles” folder. Other CAB files
in the “\SDMMC\Cabfiles” folder may cause problems with testing, remove or uninstall these before proceeding. At least 80% (4 of 5 bars)
CDMA signal strength for a successful over-the-air activation.
Download and Activate Sprint Watcher
1 Make sure the Registry Restore feature on your 760 Computer is disabled. Select Start > Settings > the System tab. Tap the Utilities desktop icon, then the Registry Save tab. Clear Enable Registry Save.
700 Series Color Mobile Computer User’s Manual
137
Chapter 4 — Network Support
2 Perform a cold-boot on your 760 Computer, then go through the normal Pocket PC set-up (i.e. Align Screen etc.).
3 Important! Set the Date and Time.
4 Tap the Sprint_Watcher_PPC_2002-03xxx.CAB file to perform the
installation.
5 Perform a warm-boot on your 760 Computer to load the CAB file.
6 From the Today screen, tap the LAN Network icon in the System Tray.
7 In the NDISTRAY pop-up menu (the Network Driver Interface Specification tray application), select No Networking and Auto FTP Off.
Tap anywhere on the screen to close the menu.
8 Tap Start > Programs > the Watcher icon to launch the SB555 Watcher program.
9 Tap Yes, I accept to accept the license agreement, then tap OK to continue. This license agreement does not appear again after this installation.
Tap OK for the 760 Computer to perform a warm-boot and complete the
installation.
138
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
Using Sprint Watcher
Before you start using the Sprint Watcher application, make sure you
match the correct ESN with each 760 Computer and that you have at least
80% CDMA signal strength.
The ESN that you give to your provider is either on the box or on a label
inside the battery compartment. The label would include the “ESN” term
and a bar code along with the serial number.
1 Tap Start > Programs > the Watcher icon or tap the Watcher icon from
the NDISTRAY via the Today screen (circled in the following illustration) to launch the SB555 Watcher program.
2 If your 760 Computer was not previously activated, Watcher automatically starts the Activation Wizard. Otherwise, select Manual Activation
to continue.
700 Series Color Mobile Computer User’s Manual
139
Chapter 4 — Network Support
3 Enter the MSL or lock code received from Sprint.
4 Enter the phone number (MIN) and MSID received from Sprint.
These numbers may be the same.
5 After entering the phone number and MSID, the modem then resets
and the Watcher application displays the screens shown here:
Note: If the “searching for SB555” screen does not proceed to the next
screen after 30-40 seconds, perform a warm-boot on your 760 Computer, then restart the Watcher program.
140
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
Data Provisioning
At this point, the activation on the Sprint network is complete. It is recommended by Sprint to wait before you launch data provisioning to allow
time for the activation to propagate through your Sprint network.
Before you manually launch data provisioning, wait at least 30 minutes. In
some cases, you may have to wait up to two hours.
1 If Data Provisioning does not start automatically, select Admin > Data
Provisioning from the bottom menu bar.
2 Tap Yes to proceed with data provisioning.
3 Activation over the air typically takes 1–20 minutes.
If data provisioning fails, do the following:
S If Data Provisioning fails and the message “could not prepare data services, please contact Sprint” displays, retry the Data Provisioning step by
tapping the “Admin” menu icon at the bottom of the Watcher screen.
Select “Data Provisioning...” and answer “yes” to the request.
700 Series Color Mobile Computer User’s Manual
141
Chapter 4 — Network Support
S If after several attempts to complete the Data Provisioning over the air,
it may be necessary to manually enter the data activation method.
S Go to Intermec Knowledge Central www.intermec.com, then select Service & Support > Knowledge Central) to learn about manual activation. The article (number 5749) is titled How to Manually Activate a
Sprint CDMA WAN Radio in the 760 Device.
4 The following screen appears once data provisioning is complete:
5 Test the data connection by tapping on the “connect” button to make a
data connection to the network. Watcher progresses through the following two screens. Once you see the second screen you know that your
mobile computer has successfully connected to the 1XRTT network.
142
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
6 Select Start > Internet Explorer, then tap Pocket Internet Explorer to
choose a web site. Your unit is now successfully activated.
Perform a cold-boot on your 760 Computer to uninstall the Watcher application. Watcher is intended for activation purposes only. Use the following to establish and maintain connection to the WAN radio:
S Custom application using Intermec WWAN Toolkit API
S Custom customer application using Connection Manager Interface
Telus and Bell Mobility Activation
Activation of Bell Mobility and Telus are similar to the first portion of the
Sprint activation process. Follow the instructions for manual activation
using the Bell Mobility Watcher.CAB or Telus Watcher.CAB file to install
the applicable application. Enter the activation lock codes and phone numbers as requested.
Bell Mobility
Telus
Username
10 digit phone
number@1xbell.ca
10-digit phone
number@1x.telusmobility.com
Password
Original Voice Mail system password (usually a 4
digit #) available from activating organizations.
The 11-digit ESN printed inside the 760 Computer battery compartment, begins with 099.
SID
16420
16422
AT Command Interface (760 Computers)
This interface specification is based on the following recommendation:
S ETSI GSM 07.05:
European Digital Cellular Telecommunication System (phase 2)
Use of DTE-DCE interface for Short message and cell broadcast service.
S ETSI GSM 07.07:
European Digital Cellular Telecommunication System (phase 2)
AT command set for GSM Mobile Equipment.
S ITU-T Recommendation V.25 ter
Serial asynchronous automatic dialing and control.
700 Series Color Mobile Computer User’s Manual
143
Chapter 4 — Network Support
Note: You need the Adobe Acrobat Reader application to view a PDF document. Go to www.adobe.com/prodindex/acrobat/readstep.html to install
or download the latest Adobe Acrobat Reader.
Command Set for Sierra Wireless SB555
Use the AT command interface from Sierra Wireless to program the
CDMA/1xRTT SB555 radio module. Documentation for this interface is
available via the following URL. Click the “General AT command reference” link for a PDF document, which is 680 KB in size.
Command Set for Siemens MC45, MC46, or MC75
Use the MC45, MC46, or MC75 AT command interface from Siemens
AG to program the GPRS/GSM MC45, MC46, or MC75 radio module.
The following documentation is available either from Intermec or from
Siemens AG. Contact either your Intermec representative or the Siemens
AG support personnel for information.
S MC45 Siemens Cellular Engine AT Command Set
S MC46 Siemens Cellular Engine AT Command Set
S MC75 Siemens Cellular Engine AT Command Set
Testing the AT Commands (760, 761, 761B)
These commands can be sent to either WAN radio by setting up a dial-up
networking connection. Do the following to initiate this connection and
test these commands to your radio. These screens are from a 760 Computer.
1 From the 760, 761, or 761B Computer, select Start > Settings > the
Connections tab > Connections. Under My ISP, tap Add a new modem connection.
144
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
2 Enter a name for the connection, select the appropriate modem (as
listed here) from the Select a modem drop-down list, then tap Next to
continue.
S 760 Computers
“WANA on COM4”
S 761 Computers
“WANB on COM5”
S 761B Computers
“Virtual WANB”
3 Enter a phone number as it should be dialed, then tap Next to continue.
Select Start > Help for more information or tap use dialing rules to
make modifications. Note that this screen may vary based on dialing rules.
Note that when you make a manual dial-up connection, a number is
not required. You may type in any number with at least one digit.
700 Series Color Mobile Computer User’s Manual
145
Chapter 4 — Network Support
4 Tap Advanced to adjust the baud rate.
5 Select the appropriate baud rate (as listed here) from the Baud rate
drop-down list.
146
S 760 Computers
115200
S 761 Computers
57600
S 761B Computers
110
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
6 Tap the Port Settings tab, check Enter dialing commands manually,
tap ok, then tap Finish to return to the Connections screen.
7 Tap Manage existing connections from the Connections page, press
and hold the new connection for a pop-up menu, then tap Connect to
initiate the connection.
8 Wait about ten seconds for the Network Log On screen, then tap OK.
You do not need to enter information within the Network Log On screen.
Use either the onscreen keyboard, or press the keys to type any of the AT
commands provided. Press or tap Enter to send each command. The results of each command sent will print onscreen. Note that each “AT” command must start with the “at” characters.
S To see what you typed onscreen, type “ate1” to initiate the AT Echo
command, then press Enter.
700 Series Color Mobile Computer User’s Manual
147
Chapter 4 — Network Support
Remote Access (Modems)
You can set up connections to the Internet and corporate network at work
to do such activities as browsing the Internet or intranet, sending and receiving e-mail and instant messages, and synchronizing information using
ActiveSync. Connections can be made using a wireless network.
Your 700 Series Computer has two groups of connection settings: My ISP
and My Work Network. Use My ISP settings to connect to the Internet.
Use My Work Network settings to connect to any private network.
S My ISP: Once connected, you can send and receive e-mail messages by
using Inbox and view Web or WAP pages by using Pocket Internet Explorer. The communication software for creating an ISP connection is
already installed on your 700 Series Computer. Your service provider
provides the software needed to install other services, such as paging and
fax services. If this is the method you want to use, see “Connecting to
an Internet Service Provider” below.
S My Work Network: Connect to the network at your company or organization where you work. Once connected, you can send and receive
e-mail messages by using Inbox, view Web or WAP pages by using
Pocket Internet Explorer, and synchronize with your desktop. If this is
the method you want to use, see “Connecting to Work” on page 151.
Connecting to an Internet Service Provider (ISP)
You can use your ISP connection to do e-mail and Web or WAP pages.
Get your dial-up access telephone number, user name, and password from
your ISP. Note some require additional information, such as MSN/username.
To see more information regarding any screen in the wizard or while
changing settings, tap the Help icon.
1 Tap Start > Settings > the Connections tab > the Connections icon. In
My ISP, tap Add a new modem connection.
148
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
2 Enter a name for the connection, such as “ISP Connection.” If using an
external modem with a cable, select “Hayes Compatible on COM1”
from the Select a modem list. Tap Next to continue.
3 Enter the access phone number, then tap Next.
700 Series Color Mobile Computer User’s Manual
149
Chapter 4 — Network Support
4 Enter the user name, password, and domain (if provided by an ISP or
your network administrator), then tap Finish.
5 Tap the Advanced tab from the Connections screen, then tap Select
Location to specify your current location. These settings apply to all
connections. Tap Use dialing rules, tap OK,then tap Edit to continue.
730, 740, 750, 760 Screens
150
741, 751, 761 Screens
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
6 Specify your current phone type. If your phone type is pulse dialing,
check the Pulse dialing box. If your type is tone dialing (as most phone
lines are), then clear the Pulse dialing box. Continue to tap ok to close
each page and return to the Settings page.
To start the connection, use one of the following programs:
S Send and receive e-mail messages by using Inbox. Before you can use
Inbox, you need to provide the information it needs to communicate
with the e-mail server.
S Visit Web and WAP pages by using Pocket Internet Explorer. For more
information, see “Pocket Internet Explorer” on page 79.
S Send and receive instant messages with MSN Messenger. For more information, see “MSN Messenger” on page 73.
Note: To change modem connection settings in My ISP, tap Manage
existing connections. Select the desired modem connection, tap Settings,
and follow the instructions on the screen.
Connecting to Work
If you have access to a network at work, you can send e-mail messages,
view intranet pages, synchronize your 700 Color Computer, and possibly
access the Internet. You can connect to work by creating a modem connection via a RAS (Remote Access Server) account. Before you can create this
modem connection, your network administrator needs to set up a RAS
account for you. Your network administrator may also give you Virtual
Private Network (VPN) settings.
Note: To change modem connection settings in My Work Network, tap
Manage existing connections. Select the desired modem connection, tap
Edit, and follow the instructions on the screen.
To view additional information for any screen in the wizard or while
changing settings, tap the Help icon.
700 Series Color Mobile Computer User’s Manual
151
Chapter 4 — Network Support
1 Tap Start > Settings > the Connections tab > the Connections icon. In
My ISP, tap Add a new modem connection.
2 Enter a name for the connection, such as “Company Connection.” In
the Select a modem list, select your modem type, then tap Next to continue. If your modem type does not appear, try reinserting your 700
Color Computer into your modem dock.
S If using an external modem connected to your 700 Computer with a
cable, select “Hayes Compatible on COM1.”
S If using any type of external modem, select the modem by name. If a
listing does not exist for your external modem, select “Hayes Compatible on COM1.”
S Wireless connections can be made via a mobile phone network:
S If making a circuit-switched data connection, select “Cellular
Line.”
S If using GPRS/EDGE, tap “Cellular Line (GPRS).”
152
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
3 Enter the access phone number, using some of the following guidelines.
If you know part of the phone number changes frequently as you travel,
create dialing rules to avoid creating numerous modem connections for
the same phone number. For more information, tap Use Dialing Rules.
S Enter the phone number exactly as you want it dialed. For example,
if you call from a business complex or hotel that requires a nine before dialing out, enter “9” in front of the phone number.
S Enter the APN provided by your mobile phone service provider.
S When using dialing rules, phone numbers are entered differently. To
use additional numbers, such as a “9” to dial from an office complex
or hotel, you must use additional dialing rules or change dialing patterns. See “Create Dialing Rules” via your online help for information.
a In the Country/Region box, enter the appropriate code when dialing internationally. For more information, contact an operator at
your local phone company.
b In the Area code box, enter the area code. Area codes are not needed in all countries.
c Enter the main phone number, then tap Next to continue.
700 Series Color Mobile Computer User’s Manual
153
Chapter 4 — Network Support
4 If necessary, enter the user name, password, and domain (provided by
an ISP or network administrator). If a domain name was not provided,
try the connection without entering a domain name, then tap Finish.
Creating a VPN Server Connection to Work
A VPN connection connects securely to servers via the Internet. Ask your
network administrator for the user name, password, domain name,
TCP/IP settings, and host name or IP address of the VPN server. The following information applies when you have “Wireless 802.11” selected via
the NDISTRAY pop-up menu (see page 108).
To view additional information for any screen in the wizard or while
changing settings, tap the Help icon.
Note: To change existing settings in My Work Network, tap Manage
existing connections > the VPN tab. Select the desired VPN connection,
tap Settings, and follow the instructions on the screen.
1 Tap Start > Settings > the Connections tab > the Connections icon.
Tap Add a new VPN server connection beneath My Work Network.
154
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
2 In Name, enter a name for the connection, such as a company’s name.
In Host name/ IP, enter the VPN server name or IP address.
Next to VPN type, select the type of authentication to use with your
device: “IPSec/L2TP” or “PPTP.” If you are not sure which option to
choose, ask your network administrator. Tap Next to continue.
3 Select the type of authentication. If you select A pre-shared key, enter
the key provided by your network administrator.
700 Series Color Mobile Computer User’s Manual
155
Chapter 4 — Network Support
4 Enter your user name, password, and domain name as provided by your
ISP or network administrator. If a domain name was not provided, try
the connection without entering a domain name.
5 You should not need to change any Advanced settings. Instances where
to change advanced settings include the server to which you are connecting does not use dynamically-assigned addresses, and you need to
enter your TCP/IP settings; or to change server DNS or WINS settings.
To change advanced settings, tap Advanced. Otherwise, tap Finish. Insert necessary equipment, such as a network (Ethernet) card, into the
device, and use a desired program to automatically begin connecting.
Ending a Connection
When connected via modem or VPN, tap the Connectivity icon on the
navigation bar, and then select Disconnect. When connected via cable or
cradle, detach your device. When connected via Infrared, move the device
away from the other computer or device. When connected via a wireless
network, switch off the connection.
Management
Use the following tool and information to configure and manage your network. You can also contact your Intermec representative for support.
SmartSystemst Foundation Console (www.intermec.com/SmartSystems)
This tool, available as a free download from Intermec, includes a management console that provides a default method to configure and manage Intermec devices “out-of-the-box,” without the purchase of additional software licenses. This is for anyone who must configure and deploy multiple
devices or manage multiple licenses.
Use the Intermec Settings applet to gather, view, and update device configuration settings within the SmartSystems Foundation. Information about
156
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
the settings you can configure with the Intermec Settings applet is in the
Intermec Computer Command Reference Manual (P/N: 073529) available
online at www.intermec.com.
Information about the SmartSystems Foundation is available as an online
help within the SmartSystems Console application. Select SmartSystems >
Help in the console to access the manual.
See the Data Collection Resource Kit in the IDL for information about
data collection functions. The IDL is available as a download from the Intermec web site at www.intermec.com/idl. Contact your Intermec representative for more information.
Tap Start > Settings > the System tab > the Intermec Settings icon to access the applet, then tap to expand the SmartSystems Information option.
SNMP Configuration on the Mobile Computer
In short, SNMP is an application-layer protocol that facilitates the exchange of management information between network devices. The 700
Color Computer is such an SNMP-enabled device. Use SNMP to control
and configure the 700 Color anywhere on an SNMP-enabled network.
The 700 Color supports four proprietary Management Information Bases
(MIBs) and Intermec provides SNMP support for MIB-II through seven
read-only MIB-II (RFC1213-MIB) Object Identifiers (OIDs).
Note: You can only query these seven OIDs through an SNMP management station.
Management Information Base
The Management Information Base is a database that contains information
about the elements to be managed. The information identifies the management element and specifies its type and access mode (Read-Only, ReadWrite). MIBs are written in ASN.1 (Abstract Syntax Notation.1) — a machine independent data definition language. Note: Elements to be managed
are represented by objects. The MIB is a structured collection of such objects.
700 Series Color Mobile Computer User’s Manual
157
Chapter 4 — Network Support
You will find the following MIB files either in the 700 Color Management
Tools or on the web via www.intermec.com:
S INTERMEC.MIB
Defines the root of the Intermec MIB tree.
S ITCADC.MIB
Defines objects for Automated Data Collection (ADC), such as bar
code symbologies.
S ITCSNMP.MIB
Defines objects for Intermec SNMP parameters and security methods,
such as an SNMP security IP address.
S ITCTERMINAL.MIB
Defines objects for 700 Color parameters, such as key clicks.
Object Identifiers
Each object has a unique identifier called an OID, which consist of a sequence of integer values represented in dot notation. Objects are stored in
a tree structure and OIDs are assigned based on the position of the object
in the tree. For example, the internet OID is equal to 1.3.6.1. Seven MIB
OIDs are shown in the following table:
MIB-II Item
OID
Group or Table
Description
ifNumber
1.3.6.1.2.1.2.1.0
Interfaces Group
Indicates the number of adapters
present in the system. For the 700
Color Computer, if one adapter is
present in the system, then ifNumber = 1 and ifIndex = 1.
ifIndex
1.3.6.1.2.1.2.2.1.1.ifIndex
Interfaces Table (ifTable) A unique value for each interface.
The value ranges between 1 and the
value of ifNumber.
ifDescr
1.3.6.1.2.1.2.2.1.2.ifIndex
Interfaces Table (ifTable) A textual string containing information about the interface.
ifType
1.3.6.1.2.1.2.2.1.3.ifIndex
Interfaces Table (ifTable) An integer containing information
about the type of the interface. It is
equal to 1 for Other.
ipAdEntAddr
1.3.6.1.2.1.4.20.1.1.IpAddress IP address Table
(ipAddrTable)
The IP address to which this entry’s
addressing information pertains
(same as 700 IP address), where IP
Address is the valid non-zero IP address of the 700 Color Computer.
ipAdEntIfIndex
1.3.6.1.2.1.4.20.1.2.IpAddress IP address Table
(ipAddrTable)
The index value that uniquely identifies the interface to which this
entry is applicable (same as ifIndex).
ipAdEntNetMask 1.3.6.1.2.1.4.20.1.3.IpAddress IP address Table
(ipAddrTable)
Subnet mask associated with the IP
address of this entry (Subnet Mask).
158
700 Series Color Mobile Computer User’s Manual
Chapter 4 — Network Support
Configuring with SNMP
The community string allows an SNMP manager to manage the 700 Color Computer with a specified privilege level. The default read-only community string is “public” and “private” is the default read/write community string. See the specific configuration parameter to find its OID.
To configure using SNMP, configure 700 Color Computers for RF or
Ethernet communications. Determine the OID (Object Identifier) for the
parameter to be changed. The Intermec base OID is 1.3.6.1.4.1.1963.
Use your SNMP management station to get and set variables that are defined in the Intermec MIBs. You can set the traps, identification, or security configuration parameters for SNMP.
700 Series Color Mobile Computer User’s Manual
159
Chapter 4 — Network Support
160
700 Series Color Mobile Computer User’s Manual
5
Printer Support
The 700 Series Color Mobile Computer works with the following printers
from Intermec. Contact an Intermec representative for information about
these printers.
S 6808
A 4-inch belt-mount printer.
S 6820
A full-page, 80-column printer.
S 782T
A 2-inch workboard printer.
S PB20
A 2-inch belt-mount printer with a Bluetooth compatible module from
Socket Communications.
S PB42
A 4-inch wireless portable receipt printer with a Bluetooth compatible
module from Socket Communications.
Note: “700 Color” pertains to 740, 741, 750, 751, 760, and 761 Computers unless otherwise noted.
700 Series Color Mobile Computer User’s Manual
161
Chapter 5 — Printer Support
Printing ASCII
These methods for printing using Pocket PC at this time is as follows:
S Add port drivers to print ASCII directly to the port.
S Use LinePrinter ActiveX Control from the Printing Resource Kit via the
Intermec Developer Library (IDL) available as a download from the Intermec webs site at www.intermec.com/idl. Contact your Intermec representative for more information.
S Via wireless printing - see the Bluetooth Resource Kit User’s Guide for more
information.
Directly to a Port
Printing directly to the port sends RAW data to the printer. The format of
this data depends upon your application and the printer capabilities.
You must understand the printer commands available for your specific
printer. Generally, applications just send raw ASCII text to the printer.
Since you are sending data to the printer from your application directly to
the port you are in complete control of the printers operations. This allows
you to do line printing (print one line at a time) rather than the page format printing offered by the GDI approach. It is also much faster since data
does not have to be converted from one graphics format to the other (display to printer). Most Intermec® printers use Epson Escape Sequences to
control print format operations.
These commands are available in documentation you receive with your
printers or from technical support. Win32 APIs are required to print directly to the port.
Directly to a Generic Serial Port
To print directly to a generic serial port printer (non-Intermec printers):
S Use CreateFile() to open ports — COM1 can open on most devices.
S Use WriteFile() to send data directly to the printer.
S Use CloseHandle() when you are finished printing to close the port.
IrDA Printer Driver
IrDA printing is only available on the certain devices and is supported directly by the Windows CE load via the IrSock API provided by the Microsoft Win32 API without need for additional drivers. Intermec 6804, 6805,
6806, 6808 and 6820 and other IrDA printers are supported.
162
700 Series Color Mobile Computer User’s Manual
Chapter 5 — Printer Support
NPCP Printer Driver
The NPCP printer communications driver (NPCPPORT.DLL) is a
Stream Device Driver built into the operating system. The driver supports
only NPCP communications to and from the 6820 and 4820 printers over
a selected serial port.
All applications use WIN32 API functions to access drivers. Applications
easily implement basic operations through the CreateFile(), WriteFile(),
ReadFile(), DeviceIOControl(), and CloseHandle() Win32 APIs.
DeviceIOControl() functions are used to do most upgrade printer modules, printer diagnostics, and get printer configurations.
About NPCP
NPCP (Norand® Portable Communications Protocol) is a proprietary
protocol that provides session, network, and datalink services for Intermec
mobile computers in the Intermec LAN environment used with printers
and data communications.
NPCP Driver Installation and Removal
Use LPT9: for the NPCP printer device and COM1 for the last parameter. COM1 is the connection available via the 700 Color Computer.
Applications use the RegisterDevice() function to install the driver.
DeregisterDevice() uninstalls the device driver and frees memory space
when the driver is not required. Use the HANDLE returned by
RegisterDevice() as the parameter to DeregisterDevice().
Use the RegisterDevice() function call as demonstrated below. Specify the
full path name to the driver starting at the root for the RegisterDevice()
function to work properly. The last parameter to RegisterDevice() is a
DWORD that represents the name of the port for the NPCP stream
driver to use. Build this parameter on the stack if it is not to be paged out
during the call. The first parameter “LPT” (Device Name) and the second
parameter “9’ (index), indicate the name of the registered device, such as
LPT9. This is used in the CreateFile() function call.
Install()
HANDLE hDevice;
TCHAR port[6];
port[0] = TCHAR(‘C’);
port[1] = TCHAR(‘O’);
port[2] = TCHAR(‘M’);
port[3] = TCHAR(‘1’);
port[4] = TCHAR(‘:’);
port[5] = TCHAR(0);
hDevice = RegisterDevice ( (TEXT(”LPT”), 9,
TEXT(“\\STORAGE CARD\\WINDOWS\\NPCPPORT.dll”), (DWORD)port);
700 Series Color Mobile Computer User’s Manual
163
Chapter 5 — Printer Support
Opening the NPCP Driver
The application opens the NPCP driver by using the CreateFile()
function. The call can be implemented as follows. The first parameter
“LPT9:” must reflect the device name and index used in the
RegisterDevice() function call and will fail for any of the following reasons:
hFile = CreateFile(_T(”LPT9:”), GENERIC_WRITE |
GENERIC_READ, 0, NULL, OPEN_ALWAYS, FILE_ATTRIBUTE_NORMAL,
NULL);
S The port associated with the device during RegisterDevice() is in use.
S The NPCP device is already open.
S The share mode is not set to zero. The device cannot be shared.
S Access permissions are not set to GENERIC_WRITE |
GENERIC_READ. Both modes must be specified.
Closing the NPCP Driver
Using the CloseHandle() (hFile) function closes the NPCP driver. Where
hFile is the handle returned by the CreateFile() function call.
S TRUE = the device is successfully closed.
S FALSE = an attempt to close NULL HANDLE or already closed device.
Reading from the NPCP Driver
Reading of the NPCP printers is not supported since all responses from
the printer are the result of commands sent to the printer.
DeviceIoControl() functions are provided where data is to be received
from the printer.
Writing to the NPCP Driver
All Print data can be sent to the printer using the WriteFile() function.
The print data written to the driver must contain the proper printer
commands for formatting. If the function returns FALSE, the NPCP error
may be retrieved using IOCTL_NPCP_ERROR. See the description on
the next page.
NPCP Driver I/O Controls
An application uses the DeviceIoControl() function to specify an printer
operation to be performed. Certain I/O controls are required to bind and
close communication sessions with the printer, and must be completed
before any other commands to the driver can execute properly.
The function returns TRUE to indicate the device successfully completed
its specified I/O control operation, otherwise it returns FALSE. The
following I/O control codes are defined:
164
700 Series Color Mobile Computer User’s Manual
Chapter 5 — Printer Support
#define IOCTL_NPCP_CANCEL
CTL_CODE(FILE_DEVICE_SERIAL_PORT,0x400,METHOD_BUFFERED,FILE_ANY_ACCESS)
#define IOCTL_NPCP_BIND
CTL_CODE(FILE_DEVICE_SERIAL_PORT,0x401,METHOD_BUFFERED,FILE_ANY_ACCESS)
#define IOCTL_NPCP_CLOSE
CTL_CODE(FILE_DEVICE_SERIAL_PORT,0x402,METHOD_BUFFERED,FILE_ANY_ACCESS)
#define IOCTL_NPCP_ERROR
CTL_CODE(FILE_DEVICE_SERIAL_PORT,0x403,METHOD_BUFFERED,FILE_ANY_ACCESS)
#define IOCTL_NPCP_FLUSH
CTL_CODE(FILE_DEVICE_SERIAL_PORT,0x404,METHOD_BUFFERED,FILE_ANY_ACCESS)
#define IOCTL_NPCP_IOCTL
CTL_CODE(FILE_DEVICE_SERIAL_PORT,0x405,METHOD_BUFFERED,FILE_ANY_ACCESS)
#define IOCTL_NPCP_PRTVER
CTL_CODE(FILE_DEVICE_SERIAL_PORT,0x406,METHOD_BUFFERED,FILE_ANY_ACCESS)
S IOCTL_NPCP_CANCEL
This cancels all printing at the printer. It flushes the printer buffers and
reinitializes the printer to its default state. No parameters are required.
S IOCTL_NPCP_BIND
This command is required before any data is sent or received by the
printer. Once the driver is opened, the application must bind the communications session with the printer before any data can be sent or received by the printer. If an error occurs during the bind, the application
may use IOCTL_NPCP_ERROR to get the current extended error
code. No parameters are required.
S IOCTL_NPCP_CLOSE
This command closes the current session with the printer. This function
always returns TRUE. No parameters are required.
S IOCTL_NPCP_ERROR
This command returns the extended NPCP error code in PL/N format.
The word returned will contain the PL/N compatible error code in the
low byte and completion flags in the high byte. If the frame that returned an error was not received correctly by the printer the
FRAME_NOT_ACKED bit will be set in the high byte. This operation
always returns TRUE. An output buffer of at least 2 bytes is required.
See “NPCP Error Codes” on page 166.
S IOCTL_NPCP_FLUSH
This command allows the application to poll the printer for errors while
the report is completing the print process at the printer. If an error occurs during the polling process, the operation will return FALSE and
the application can get the extended error code by using
IOCTL_NPCP_ERROR. No parameters are required.
NPCP Printer Communications
All NPCP printer communications should be based on the following flow:
1 Use CreateFile(); to open the printer driver.
2 Use IOCTL_NPCP_BIND to bind a session with the printer;
IOCTL_NPCP_ERROR to check for errors on the bind to ensure success; and IOCTL_NPCP_CANCEL to cancel outstanding print jobs.
700 Series Color Mobile Computer User’s Manual
165
Chapter 5 — Printer Support
3 Use IOCTL_NPCP_FLUSH to poll the printer to free up printer buffer resources. Use IOCTL_NPCP_FLUSH to poll the printer’s status. If
an error is reported by the IOCTL, then use IOCTL_NPCP_ERROR
to get the error and determine the correct recovery procedure.
4 Use WriteFile(); to write data to the printer. Check for errors and that
all data were written. Use IOCTL_NPCP_ERROR to get the extended
error. If the error is critical in nature, use IOCTL_NPCP_CLOSE, followed by CloseFile(), to end the communications session. Start a new
session, beginning with step 1 to ensure proper printing. For noncritical
errors display the error and retry the operation.
5 After all data is sent to the printer, ensure that the printer continues to
print the report properly by polling the printer’s status. Use
IOCTL_NPCP_FLUSH to poll the printer’s status. If an error is reported by the IOCTL, then use IOCTL_NPCP_ERROR to get the
error and determine the correct recovery procedure.
Sample Code
See sample code in the “\700C Dev Tools\Installable Drivers\Port
Drivers\Npcp\NPCPPrint\” directory for more details on printing, printer
communications and error code handling.
NPCP Error Codes
Call the IOCTL_NPCP_ERROR I/O control to receive PL/N compatible
error codes. Applications must decide how to act on the data returned.
// Definition of NPCP communications Errors and Printer Errors
#define PNRDY (BYTE)102 // link not ready error
#define RXTMO (BYTE)104 // link no receive error
#define TXTMO (BYTE)106 // link no transmit error
#define BADADR (BYTE)111 // frame address error
#define GAPERR (BYTE)112 // link gap error (timeout) in receive data
#define LSRPE (BYTE)113 // frame parity error on length field
#define IFTS (BYTE)120 // session layer - invalid frame this state
#define NS_NE_VR (BYTE)121 // session layer sequence error
#define NR_NE_VS (BYTE)122 // session layer sequence error
#define MAC_CRCERR (BYTE)124 // MAC CRC error
#define RLENERR (BYTE)123 // MAC too much data received
#define FRMERR (BYTE)200 // Frame Reject
#define FRMERR_IF (BYTE)201 // Frame Reject - Invalid Frame
#define FRMERR_NR (BYTE)202 // Frame Reject - NR Mismatch
#define FRMERR_NS (BYTE)203 // Frame Reject - NS Mismatch
#define NDMERR (BYTE)204 // Normal Disconnect mode error
#define BINDERR (BYTE)210 // bind error
#define IPLDUR (BYTE)221 // invalid presentation layer response
#define HEADJAM (BYTE)222 // printer head jam
#define PAPEROUT (BYTE)223 // printer paper out
#define LOWVOLTS (BYTE)224 // printer low voltage
#define HIVOLTS (BYTE)225 // printer over voltage
#define LOWBAT (BYTE)226 // printer low battery
#define COVEROFF (BYTE)227 // printer cover off error
#define HEADFAULT (BYTE)228 // printer head short or driver short error
#define PFFAULT (BYTE)229 // paper feed motor fault.
#define FRAME_NOT_ACKED 0x8000 // frame was not received by printer and need
to be resent.
166
700 Series Color Mobile Computer User’s Manual
Chapter 5 — Printer Support
O’Neil Printer Driver
The DTR printer communications driver is a Stream Device Driver
named ONEIL.DLL.
All applications use WIN32 API functions to access drivers. Applications
easily implement basic operations using the CreateFile(), WriteFile(),
DeviceIOControl() and CloseHandle() Win32 APIs.
The driver supports communications to 6804DM, 6804T, 6805A, 6806,
6808, 681T, PB20, and PB42 printers over a selected serial port.
DTR Driver Installation and Removal
Your application must use the RegisterDevice() function to install the
ONEIL.DDL device driver. Use “DTR” for the Device Name parameter,
“1” for the Device Driver index parameter, and any of these strings for the
last parameter:
S NULL (==0) Defaults to COM1 @ 9600
S “COM1” only COM port specified defaults to 9600
S “COM1:9600” sets to COM port and specified bit rate
S “COM1:19200” sets to COM port and specified bit rate
Use the HANDLE returned by RegisterDevice() as the parameter to
DeregisterDevice(). The correct usage of the RegisterDevice() function call
is shown below. You may use DeregisterDevice() to uninstall the driver.
Install()
HANDLE hDevice;
TCHAR port[6];
port[0] = TCHAR(‘C’);
port[1] = TCHAR(‘O’);
port[2] = TCHAR(‘M’);
port[3] = TCHAR(‘1’);
port[4] = TCHAR(‘:’);
port[5] = TCHAR(0);
hDevice = RegisterDevice ( (TEXT(”DTR”), 1, TEXT(”\\WINDOWS\\ONEIL.DLL”),
(DWORD)port);
Opening the DTR Driver
The application opens the DTR driver by using the CreateFile() function.
The call can be implemented as follows:
hFile = CreateFile(_T(”DTR1:”), GENERIC_WRITE, 0, NULL,
OPEN_ALWAYS, FILE_ATTRIBUTE_NORMAL, NULL);
The first parameter “DTR1:” must reflect the device name and index used
in the RegisterDevice() function call.
700 Series Color Mobile Computer User’s Manual
167
Chapter 5 — Printer Support
The function call will fail for any of the following reasons:
S Port associated with device during RegisterDevice() is currently in use.
S The DTR device is already open.
S The share mode is not set to zero. The device cannot be shared.
S Access permissions are not set to GENERIC_WRITE.
Closing the DTR Driver
Using the CloseHandle() (hFile) function closes the DTR driver. Where
hFile is the handle returned by the CreateFile() function call.
S TRUE indicates the device is successfully closed.
S FALSE indicates an attempt to close a NULL HANDLE or an already
closed device.
Writing to the DTR Driver
Use the WriteFile() function to send all print data to the printer. The data
must contain the proper formatting printer commands.
DTR Printer Communications
All DTR printer communications should be based on the following flow:
1 Use CreateFile() to open the printer driver.
2 Use WriteFile() to write your data to the printer. Check for errors and
that all data were written.
3 Use CloseHandle() to close the driver.
Configuring PB42 Printers Via Intermec Settings
Tap Start > Settings > the System tab > the Intermec Settings icon to access the applet. Tap (+) to expand the Printers option, then tap (+) to expand the PB42 Settings option and make your adjustments.
168
700 Series Color Mobile Computer User’s Manual
6
Scanner Support
The 700 Series Color Mobile Computer is available with imaging or laser
scanning technologies, including the following:
APS Linear Imager: (standard for 730 Computers)
— includes the EV10 Scan Engine
Reads 1D symbologies and PDF417 bar codes. Linear imaging using Vista Scanning technology reads low-contrast bar
codes, laminated bar codes, and bar codes displayed on CRT
or TRT displays. This imaging uses harmless LEDs for illumination and does not require any warning labels. Vista Scanning is more reliable than lasers as it is a completely solid state
with no moving parts or oscillating mirrors.
2D Imager: (not supported on 730 Computers)
— includes the IT4000 Scan Engine
This decodes several stacked 1D and 2D symbologies, including PDF417, Data Matrix, and MaxiCode without “painting.” It can also read 1D codes from any orientation, for example the scan beam does not need to align perpendicular to
the symbol to read it. Photography is a secondary application;
the lens in the device favors bar code reading. Photos are
640x480, 256 gray-scale.
1D Laser Scanner: (not supported on 730 Computers)
— includes the SE900, SE900HS, SE900-S6, and
SE900HS-S6 scan engines
Traditional laser scanner that decodes 1D bar codes.
PDF417 Laser Scanner: (not supported on
730 Computers)
Higher speed laser scanner that can read PDF417 labels by
“painting” the label.
EL10 Laser Scanner
An EXCELeratet bar code laser scan engine, based on the
Micro Electro Mechanical System (MEMS) technology, that
is significantly faster, lighter, and more efficient than traditional laser scanners.
700 Series Color Mobile Computer User’s Manual
169
Chapter 6 — Scanner Support
A 700 Color ImageDemo application demonstrates the more common features of the 700 Color Computer imager. See the ImageDemo User’s Guide
for information.
Note: “700 Color” pertains to 740, 741, 750, 751, 760, and 761 Computers unless otherwise noted.
Scanner Control and Data Transfer
Note: To use the methods described below, enable Data Collection functionality on the 700 Computer using the bootloader configuration menu.
The Data Server and associated software provide several ways to manipulate scanner control and data transfer between the scanner subsystem and
user applications:
S Automatic Data Collection COM Interfaces:
These COM interfaces allow user applications to receive bar code data,
and configure and control the bar code reader engine.
S ITCAxBarCodeReaderControl functions:
These ActiveX controls allow user applications to collect bar code data
from the scanner, to configure the scanner, and to configure audio and
visual notification when data arrives.
S ITCAxReaderCommand functions:
Use these ActiveX controls to modify and retrieve configuration information using the reader interface commands.
S Scanning EasySet bar code labels:
You can use the EasySetR bar code creation software from Intermec to
print configuration labels. Scan the labels to change the scanner configuration and data transfer settings.
Use the Intermec EasySet software to print configuration labels you can
scan to change your configuration settings. For more information, see
the EasySet online help. EasySet is available from the Intermec Data
Capture web site.
For more information, see the Data Collection Resource Kit in the Intermec Developer Library (IDL), which is available as a download from the
Intermec web site at www.intermec.com/idl. Contact your Intermec representative for more information.
Data Collection Configuration
You can configure scanner and reader settings for the 700 Color Computer via the Intermec Settings applet. From the 700 Color Computer, tap
Start > Settings > the System tab > the Intermec Settings icon. See the
Intermec Computer Command Reference Manual (P/N: 073529) for information about the settings you can configure with this applet. This online
manual is available from the Intermec web site at www.intermec.com.
170
700 Series Color Mobile Computer User’s Manual
Chapter 6 — Scanner Support
Internal Scanners
The Intermec Internal Scanner feature allows Automatic Data Collection
(ADC) by accepting data from the COM1 port and wedging it into the
keyboard interface. You can enable or disable this feature from the Today
screen on the 700 Color Computer.
Before you configure your internal scanner, adjust its settings using the
Intermec Settings applet. Information about the settings you can configure
with this applet is described in the Intermec Computer Command Reference
Manual. The online manual is available from the Intermec web site at
www.intermec.com.
1 From the 700 Color Computer, tap Start > Settings > the System tab >
the Intermec Settings icon.
2 Tap the Data Collection option, then tap (+) to expand Internal
Scanner. This sample screen is for the IT4000 scan engine.
700 Series Color Mobile Computer User’s Manual
171
Chapter 6 — Scanner Support
Scanner and Imager Settings
Depending on what is selected as the scanner model, image settings, decode security, scanner settings, and virtual wedge are configured from the
Intermec Settings applet. See the the Intermec Computer Command Reference Manual, available from the Intermec web site at www.intermec.com,
for more information about each enabled option.
Internal Scanner Supported Symbologies
Symbologies
EL10
EV10
IT4000
SE900
SE900HS
SE900-S6
SE900HS-S6
Code39
UPC/EAN
Code 128
Interleaved 2 of 5
Code 93
Codabar
Code 2 of 5
MSI
Plessey
Code 11
Matrix 2 of 5
Telepen
PDF417
Micro PDF417
MaxiCode
Data Matrix
QR Code
RSS 14
Available in
f/w Sxxp304
Available in
f/w Sxxp304
RSS Limited
Available in
f/w Sxxp304
Available in
f/w Sxxp304
RSS Expanded
Available in
f/w Sxxp304
Available in
f/w Sxxp304
Codablock A
Codablock F
UCC Composite
TLC 39
172
700 Series Color Mobile Computer User’s Manual
Chapter 6 — Scanner Support
Reading Distances
Typical reading distances are done in an office environment using office
lights (4 lux). Minimum distances are measured in the dark (0 lux). Both
reading distances are provided in respective scan engine integration guides.
Contact your Intermec representative for more information.
Below are minimum standard reading distances for 700 Color Computers
built with integrated scan engines. When correctly mounted, an exit window reduces reading distances by about 4% for all scan engines, with the
exception of the EL10 with its reading distances reduced by about 25%.
EA10 Minimum Reading Distances with 0.04” Setbacks
Symbology
Density
Minimum Distance
Maximum Distance
Code 39
0.125 mm/ 5 mil
0.15 mm/ 6 mil
0.20 mm/ 8 mil
0.25 mm/ 10 mil
0.30 mm/ 12 mil
0.5 mm/ 20 mil
1.0 mm/ 40 mil
8.03 cm/ 3.16”
7.39 cm/ 2.91”
5.49 cm/ 2.16”
3.96 cm/ 1.56”
3.71 cm/ 1.46”
4.98 cm/ 1.96”
3.71 cm/ 1.46”
11.84 cm/ 4.66”
14.38 cm/ 5.66”
19.46 cm/ 7.66”
24.03 cm/ 9.46”
25.81 cm/ 10.16”
35.97 cm/ 14.26”
50.95 cm/ 20.06”
4.98 cm/ 1.96”
29.87 cm/ 11.76”
UPC/EAN
PDF417
0.168 mm/ 6.6 mil
0.254 mm/ 10 mil
0.381 mm/ 15 mil
7.26 cm/ 2.86”
4.47 cm/ 1.76”
10.06 cm/ 3.96”
12.85 cm/ 5.06”
20.98 cm/ 8.26”
28.35 cm/ 11.16”
Data Matrix
0.254 mm/ 10 mil
0.381 mm/ 15 mil
0.508 mm/ 20 mil
6.50 cm/ 2.56”
5.99 cm/ 2.36”
4.98 cm/ 1.96”
17.93 cm/ 7.06”
27.84 cm/ 10.96”
32.92 cm/ 12.96”
700 Series Color Mobile Computer User’s Manual
173
Chapter 6 — Scanner Support
EA11 Standard Minimum Reading Distances with 0.04” Setbacks
Symbology
Density
Minimum Distance
Maximum Distance
Code 39
0.125 mm/ 5 mil
0.20 mm/ 8 mil
0.25 mm/ 10 mil
0.5 mm/ 20 mil
7.26 cm/ 2.86”
3.96 cm/ 1.56”
3.45 cm/ 1.36”
4.98 cm/ 1.96”
12.09 cm/ 4.76”
20.98 cm/ 8.26”
25.04 cm/ 9.86”
40.28 cm/ 15.86”
UPC/EAN
0.33 mm/ 13 mil
4.98 cm/ 1.96”
29.62 cm/ 11.66”
Data Matrix
0.191 mm/ 7.5 mil
0.254 mm/ 10 mil
0.381 mm/ 15 mil
3.71 cm/ 2.46”
5.98 cm/ 1.96”
16.41 cm/ 6.46”
20.73 cm/ 8.16”
27.58 cm/ 10.86”
PDF417
0.168 mm/ 6.6 mil
0.254 mm/ 10 mil
0.381 mm/ 15 mil
6.25 cm/ 2.46”
4.47 cm/ 1.76”
4.98 cm/ 1.96”
13.87 cm/ 5.46”
21.74 cm/ 8.56”
33.43 cm/ 13.16”
* Minimum distance depends on symbology length and scan angle.
174
700 Series Color Mobile Computer User’s Manual
Chapter 6 — Scanner Support
EL10 Minimum Guaranteed Reading Distances with 0.25” Setbacks
Symbology
Density
Minimum Distance
Maximum Distance
Code 39
0.1 mm/ 4 mil
0.125 mm/ 5 mil
0.25 mm/ 10 mil
0.5 mm/ 20 mil
1 mm/ 40 mil
8.51 cm/ 3.35”
7.75 cm/ 3.05”
6.99 cm/ 2.75”
6.48 cm/ 2.55”
7.75 cm/ 3.05”
12.30 cm/ 4.45”
14.35 cm/ 5.65”
29.34 cm/ 11.55”
50.17 cm/ 19.75”
63.37 cm/ 24.95”
UPC/EAN
0.33 mm/ 13 mil
5.46 cm/ 2.15”
34.42 cm/ 13.55”
PDF417
0.17 mm/ 6.6 mil
7.75 cm/ 3.05”
19.43 cm/ 7.65”
EL11 Minimum Reading Distances with 0.04” Setbacks
Symbology
Density
Minimum Distance
Maximum Distance
0.1 mm/ 4 mil
0.125 mm/ 5 mil
0.33 mm/ 13 mil (EAN)
1 mm/ 40 mil
8.79 cm/ 3.46”
8.28 cm/ 3.26”
5.49 cm/ 2.16”
9.55 cm/ 3.86”
11.84 cm/ 4.66”
14.48 cm/ 5.86”
34.95 cm/ 13.76”
63.91 cm/ 25.16”
700 Series Color Mobile Computer User’s Manual
175
Chapter 6 — Scanner Support
EV10 Minimum Reading Distances with 0.04” Setbacks
Symbology
Bar Code Content
Density
Minimum Distance Maximum Distance
Code 39
RESO 0.100 MM
R 0.125 MM
0.25
0.5
R1MM
0.1 mm/ 4 mil
0.125 mm/ 5 mil
0.25 mm/ 10 mil
0.5 mm/ 20 mil
1 mm/ 40 mil
10.8 cm/ 4.26”
9.80 cm/ 3.86”
5.99 cm/ 2.36”
3.96 cm/ 1.56”
7.53 cm/ 2.96”
13.87 cm/ 5.46”
16.92 cm/ 6.66”
23.77 cm/ 9.36”
30.89 cm/ 12.16”
39.78 cm/ 15.66”
UPC/EAN
120010010100
0.33 mm/ 13 mil
4.98 cm/ 1.96”
25.81 cm/ 10.16”
PDF417
10 mil
15 mil
0.254 mm/ 10 mil
0.381 mm/ 15 mil
9.80 cm/ 3.86”
7.77 cm/ 3.06”
16.92 cm/ 6.66”
18.95 cm/ 7.46”
2D Area Imager Reading Distances with 0.04” Setbacks
Symbology
Density
Near Distance
Far Distance
MaxiCode
35 mil
4.98 cm/ 1.96”
33.92 cm/ 12.96”
Data Matrix
15 mil
9.30 cm/ 3.66”
16.41 cm/ 6.46”
PDF417
10 mil
8 mil
6.6 mil
7.77 cm/ 3.06”
8.28 cm/ 3.26”
11.33 cm/ 4.46”
22.76 cm/ 8.96”
20.22 cm/ 7.96”
15.77 cm/ 6.21”
Code 39
15 mil
10 mil
8 mil
5.23 cm/ 2.06”
8.03 cm/ 3.16”
8.79 cm/ 3.46”
29.87 cm/ 11.76”
23.27 cm/ 9.16”
19.20 cm/ 7.56”
UPC
13 mil
6.25 cm/ 2.46”
31.65 cm/ 12.46”
176
700 Series Color Mobile Computer User’s Manual
Chapter 6 — Scanner Support
Tethered Scanners
The Intermec Tethered Scanner feature allows Automatic Data Collection
(ADC) by accepting data from the COM1 port and wedging it into the
keyboard interface. You can enable or disable this feature from the Today
screen on the 700 Color Computer.
Configuring the Tethered Scanner
Before you configure your tethered scanner, adjust its settings using the
Intermec Settings applet. Information about the settings you can configure
with this applet is described in the Intermec Computer Command Reference
Manual. The online manual is available from the Intermec web site at
www.intermec.com.
1 Connect your tethered scanner to the tethered scanner port.
2 From the 700 Color Computer, tap Start > Settings > the System tab >
the Intermec Settings icon.
3 Tap Data Collection, then tap (+) to expand Dock Tethered Scanner.
700 Series Color Mobile Computer User’s Manual
177
Chapter 6 — Scanner Support
4 Tap (+) to expand Scanner Settings, tap Scanner model, then enter the
applicable scanner, such as “1551E” or “1553.”
5 Make sure a scanner is properly connected to your 700 Computer, tap
to check Enable scanner port, then tap File > Save Settings from the
bottom of the screen. These changes take several moments to reset.
1551E or 1553 Selected for Scanner Model
When “1551E” or “1553” is selected from the Scanner model option (see
step 4 above), and the port state is already enabled (see step 5), the process
will take several moments to reset. When 1551E or 1553 is successfully
connected during this step, the unit will emit some beeps. Here, the terminal is initializing the scanner at 9600 for the baud rate, 7 data bits, even
parity, and 2 stop bits and synchronizing the terminal’s configuration with
the attached scanner.
With “1551E” or “1553” selected, Symbologies, Symbology Options,
Hardware Trigger, and Scanner Port settings are configured from the Intermec Settings applet. See the the Intermec Computer Command Reference
178
700 Series Color Mobile Computer User’s Manual
Chapter 6 — Scanner Support
Manual, available from the Intermec web site at www.intermec.com, for
more information about each enabled option.
ASCII Selected for Scanner Model
To send data coming into the 700 Color Computer through the COM1
port from an external input device, as keyboard data to an application on
the desktop, do the following:
1 Enter “ASCII” as the Scanner model option.
2 Tap to check Enable scanner port.
3 Tap File > Save Settings from the bottom of the screen, or tap Yes
when prompted to refresh the scanner settings.
With “ASCII” selected, Symbology Options, Hardware Trigger, and Scanner Port settings are configured from the Intermec Settings applet. See the
the Intermec Computer Command Reference Manual, available from the Intermec web site at www.intermec.com, for more information about each
enabled option.
Note: When selecting either the 1551E or the 1553 Scanner or enabling
the scanner port for these scanners, the 700 Computer tries to communicate with the attached scanner. If the scanner is not powered, if the cable is
not connected properly, the wrong cable is used, or if the scanner firmware
is older than 2.0, and the “Failed to save one or more settings” message
appears, then this step failed.
This process can take time as the terminal is going through a group of
RS-232 settings to communicate with the scanner. After successful communicated with the scanner (about eight beeps are generated), it initializes
the scanner with the 700 Computer’s current settings. This process might
generate a series of beeps pending on the firmware version installed in the
scanner. These beeps are suppressed in firmware versions 2.08 or greater.
Troubleshooting the 1551E/1553 Tethered Scanner
Do the following to troubleshoot your 1551E/1553 Tethered Scanner:
1 Ensure the correct cable is used for the scanner on the tethered scanner
port. Note the 700 Computer cannot supply power to the scanner.
2 Perform a quick test to determine whether the connection is good.
Temporary select the scanner model as “ASCII,” then enable the scanner port state. Go to a command prompt or a notepad and scan a data
label. If a label is wedged into the command prompt or notepad, then
the connection is good.
3 If step 2 passes, reset the scanner configurations to their defaults (scan
the Reset Factory Defaults label on the next page) to prevent miscommunication, then reenable the scanner port state.
4 If step 2 fails, then the firmware installed in the tethered scanner may be
older than version 2.0. Upgrade your scanner firmware.
700 Series Color Mobile Computer User’s Manual
179
Chapter 6 — Scanner Support
Reset Factory Defaults
Scan the EasySet software bar code label “Reset Factory Default” to restore
all of your scanner’s configurations to their factory defaults. When this
command label is scanned, reinitialize the tethered scanner (such as disable
the scanner port state, then enable it) on the 700 Computer. Otherwise,
the online configuration and scanning on the 700 Computer are not functional. In general, scan this label only to initially reset the scanner.
Do not scan EasySet command labels to change the following settings:
S Symbologies code mark
S Code 128, EAN29 Identifier
S Preamble and Postamble
S Enable/Disable symbologies
S Symbology ID transmit option
In some cases, scanning EasySet Command labels cause the current setting
on the user interface to be out of sync with the scanner settings. However,
in some cases, scanning these labels does corrupt scanned data.
The “Open COMx error: 0x00000037” message appears if the COM port
cannot open due to another application using the port. Disable that application to free up the COM1 port before you can enable the scanner. “x”
is the COM port number, such as 1, 2, or 3.
Tethered Scanner Supported Symbologies
The user interface may allow configuration of PDF417, Micro PDF417,
RSS, and Codablock bar code symbologies. However, these symbologies
are dependant on what scanner models and firmware versions are in use.
See the following table for a guideline on each supported symbology:
You can use a generic ASCII scanner with the 700 Color Computer.
Pending on the scanner, linear symbologies such as Code39, should decode correctly. However, 2D symbologies such as PDF417 may not decode correctly.
Symbologies
1551E
1553
Code39
UPC/EAN
Code 128
Interleaved 2 of 5
Code 93
Codabar
Code 2 of 5
MSI
Plessey
Code 11
Matrix 2 of 5
Telepen
180
700 Series Color Mobile Computer User’s Manual
Chapter 6 — Scanner Support
Symbologies
PDF417
Micro PDF417
1551E
1553
Available in 1551 0808 PDF
Available in 1551 0808 PDF, Sxxp217_ or later
MaxiCode
Data Matrix
QR Code
RSS 14
F/w version 2.15 or later
F/w version 2.15 or later
RSS Limited
F/w version 2.15 or later
F/w version 2.15 or later
RSS Expanded
F/w version 2.15 or later
F/w version 2.15 or later
Codablock A
Available in 1551 0808 PDF
Codablock F
Available in 1551 0808 PDF
UCC Composite
Attached RFID Readers
Note: The 700 Color Computer currently supports only the IP4 Intellitag
Portable RFID Reader, a trigger handle accessory that lets you hold your
700 Color Computer like a reader or scanner. Contact your Intermec representative for more information.
Radio frequency identification (RFID) systems evolved as a way to provide
all the benefits of visual scanning systems, while overcoming many of their
limitations. Radio frequency (RF) describes electromagnetic waves in the
10 kHz to 10 GHz range. Electronic identification (ID) systems transfer
data messages from an object to be identified to a data management system. RFID systems use radio frequency to transfer data between an item
being tracked and a reader/writer. It is a fast, automatic identification
technology.
More information about RFID and the IP4 Reader are in the following
Intermec publications. PDFs of these publications are available from the
Intermec web site at www.intermec.com.
S Basic Reader Interface Programmer’s Reference Manual
(P/N: 937-000-001)
S Intermec RFID System Manual (P/N: 936-000-001)
S IP4 Handheld Reader Instructions (P/N: 943-002-002)
S IP4 Handheld Reader Manual Supplement (P/N: 933-000-001)
Reading RFID Tags with the Virtual Wedge
The virtual wedge is a Data Collection services feature that enters bar code
and RFID tag data into a software application as if it were typed at the
keypad. This section explains how to configure the 700 Color Computer
to read RFID tags through the virtual wedge. Contact your Intermec representative for more information about the virtual wedge.
700 Series Color Mobile Computer User’s Manual
181
Chapter 6 — Scanner Support
Do the following to configure your virtual wedge to do RFID tags.
S Configure at least one scan button on the 700 Color Computer to trigger RFID (go to the next paragraph).
S Disable power to Bluetooth (go to page 183 for instructions).
S Enable the IP4 Reader (go to page 184 for instructions).
Use the Intermec Settings applet to configure at least one scan button. Information about the settings you can configure with this applet is described in the Intermec Computer Command Reference Manual. The online
manual is available from the Intermec web site at www.intermec.com.
1 From the 700 Color Computer, tap Start > Settings > the System tab >
the Intermec Settings icon > the Device Settings option, then tap (+) to
expand the Keypad option.
2 Tap (+) to expand Scan Button Remapping, then tap (+) to expand any
of the Handle Trigger, the Left Scan Button, or the Right Scan Button
options. Note that the Handle Trigger option is for the IP4 Reader.
182
700 Series Color Mobile Computer User’s Manual
Chapter 6 — Scanner Support
3 Select RFID to change the trigger from the scanner to RFID, then select
File > Save Settings.
4 Go to the next paragraph to disable power to Bluetooth.
5 Go to page 184 to enable the IP4 Reader.
Disable Power to Bluetooth
Note: Before you configure your attached IP4 Reader, make sure Bluetooth is disabled on your 700 Color Computer.
1 Tap Start > Settings > the Connections tab > the Bluetooth icon.
2 Check whether Off is selected. If not, then check Off. Wait momentarily for Bluetooth to turn off, then click ok to close the Bluetooth applet.
700 Series Color Mobile Computer User’s Manual
183
Chapter 6 — Scanner Support
Configure the Reader Using Intermec Settings
You should also adjust its settings using the Intermec Settings applet. Information about the settings you can configure with this applet is described in the Intermec Computer Command Reference Manual. The online
manual is available from the Intermec web site at www.intermec.com.
1 Connect your reader to the reader port.
1 From the 700 Color Computer, tap Start > Settings > the System tab >
the Intermec Settings icon > the RFID option.
2 Tap (+) to expand Reader 1 and ensure Reader Model shows “IP4” as
the model of choice. If not, then tap Reader Model, tap its drop-down,
then select “IP4.”
184
700 Series Color Mobile Computer User’s Manual
Chapter 6 — Scanner Support
3 Under the Reader option, check Enable Reader to enable the attached
reader.
Once the IP4 reader is configured using the Intermec Settings applet, applications can access the IP4 Reader using the Basic Reader Interface (BRI)
protocol on the 700 Color TCP port “2189.”
700 Series Color Mobile Computer User’s Manual
185
Chapter 6 — Scanner Support
186
700 Series Color Mobile Computer User’s Manual
7
Programming
The following programming information pertains to the 700 Series Color
Mobile Computer:
S Creating CAB Files (page 188)
S Customization and Lockdown (page 202)
S FTP Server (page 203)
S Kernel I/O Control Functions (page 210)
S Network Selection APIs (page 221)
S Notifications (page 221)
S Reboot Functions (page 222)
S Remapping the Keypad (page 223)
Note: “700 Color” pertains to 730, 740, 741, 750, 751, 760, and 761
Computers unless otherwise noted.
700 Series Color Mobile Computer User’s Manual
187
Chapter 7 — Programming
Creating CAB Files
The Windows CE operating system uses a .CAB file to install an application on a Windows CE-based device. A .CAB file is composed of multiple
files that are compressed into one file. Compressing multiple files into one
file provides the following benefits:
S All application files are present.
S A partial installation is prevented.
S The application can be installed from several sources, such as a desktop
computer or a Web site.
Use the CAB Wizard application (CABWIZ.EXE) to generate a .CAB file
for your application.
Creating Device-Specific CAB Files
Do the following to create a device-specific .CAB file for an application, in
the order provided:
1 Create an .INF file with Windows CE-specific modifications (page
188).
2 Optional Create a SETUP.DLL file to provide custom control of the
installation process (page 197).
3 Use the CAB Wizard to create the .CAB file, using the .INF file, the
optional SETUP.DLL file, and the device-specific application files as
parameters (page 201).
Creating an .INF File
An .INF file specifies information about an application for the CAB Wizard. Below are the sections of an .INF file:
[Version]
This specifies the creator of the file, version, and other relevant information.
Required? Yes
S Signature:
“signature_name”
“$Windows NT$”
S Provider:
“INF_creator”
The company name of the application, such as “Microsoft.”
S CESignature
“$Windows CE$”
Example
[Version]
Signature = “$Windows NT$”
Provider = “Intermec”
CESignature = “$Windows CE$”
188
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
[CEStrings]
This specifies string substitutions for the application name and the default
installation directory.
Required? Yes
S AppName: app_name
Name of the application. Other instances of %AppName% in the .INF
file are replaced with this string value, such as RP32.
S InstallDir: default_install_dir
Default installation directory on the device. Other instances of %InstallDir% in the .INF file are replaced with this string value. Example:
\SDMMC_Disk\%AppName%
Example
[CEStrings]
AppName=“Game Pack”
InstallDir=%CE1%\%AppName%
[Strings]
This section is optional and defines one or more string keys. A string key
represents a string of printable characters.
Required? No
S string_key: value
String consisting of letters, digits, or other printable characters. Enclose
value in double quotation marks ““”” if corresponding string key is used
in an item requiring double quotation marks. No string_keys is okay.
Example
[Strings]
reg_path = Software\Intermec\My Test App
[CEDevice]
Describes the platform for the targeted application. All keys are optional.
If a key is nonexistent or has no data, Windows CE does not perform any
checking except the UnsupportedPlatforms. If the UnsupportedPlatforms key
exists but no data, the previous value is not overridden.
Required? Yes
S ProcessorType :
processor_type
The value that is returned by SYSTEMINFO.dwProcessorType.For
example, the value for the ARM CPU is 2577
S UnsupportedPlatforms: platform_family_name
This lists known unsupported platform family names. If the name
specified in the [CEDevice.xxx] section is different from that in the
[CEDevice] section, both platform_family_name values are unsupported
for the microprocessor specified by xxx. That is, the list of unsupported
platform family names is appended to the previous list of unsupported
names. Application Manager will not display the application for an
unsupported platform. Also, a user will be warned during the setup
process if the .CAB file is copied to an unsupported device.
700 Series Color Mobile Computer User’s Manual
189
Chapter 7 — Programming
Example
[CEDevice]
UnsupportedPlatforms = pltfrm1 ; pltfrm1 is unsupported
[CEDevice.SH3]
UnsupportedPlatforms = ; pltfrm1 is still unsupported
S VersionMin:
minor_version
Numeric value returned by OSVERSIONINFO.dwVersionMinor. The
.CAB file is valid for the currently connected device if the version of
this device is greater than or equal to VersionMin.
S VersionMax:
major_version
Numeric value returned by OSVERSIONINFO.dwVersionMajor. The
.CAB file is valid for the currently connected device if the version of
this device is less than or equal to VersionMax.
S BuildMin:
build_number
Numeric value returned by OSVERSIONINFO.dwBuildNumber. The
.CAB file is valid for the currently connected device if the version of
this device is greater than or equal to BuildMin.
S BuildMax:
build_number
Numeric value returned by OSVERSIONINFO.dwBuildNumber. The
.CAB file is valid for the currently connected device if the version of
this device is less than or equal to BuildMax.
Example
The following code example shows three [CEDevice] sections: one that
gives basic information for any CPU and two that are specific to the SH3
and the MIPS microprocessors.
[CEDevice]
UnsupportedPlatforms = pltfrm1
; A “template” for all platforms
; Does not support pltfrm1
; The following specifies version 1.0 devices only.
VersionMin = 1.0
VersionMax = 1.0
[CEDevice.ARM]
; Inherits all [CEDevice] settings
; This will create a .CAB file specific to ARM devices.
ProcessorType = 2577
; ARM .cab file is valid for ARM microprocessors.
UnsupportedPlatforms =
; pltfrm1 is still unsupported
; The following overrides the version settings so that no version checking is
performed.
VersionMin =
VersionMax =
[CEDevice.MIPS]
; Inherits all [CEDevice] settings
; This will create a .CAB file specific to “MIPS” devices.
ProcessorType = 4000
; MIPS .CAB file is valid for MIPS
microprocessor.
UnsupportedPlatforms =pltfrm2 ; pltfrm1, pltfrm2 unsupported for MIPs .CAB
file.
Note: To create the two CPU-specific .CAB files for the SETUP.INF file
in the previous example, run the CAB Wizard with the “/cpu arm mips”
parameter.
190
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
[DefaultInstall]
This describes the default installation of your application. Note that under
this section, you will list items expanded upon later in this description.
Required? Yes
S Copyfiles:
copyfile_list_section
Maps to files defined later in the .INF file, such as Files.App, Files.Font,
and Files.Bitmaps.
S AddReg:
add_registry_section
Example: RegSettings.All
S CEShortcuts:
shortcut_list_section
String that identifies one more section that defines shortcuts to a file, as
defined in the [CEShortcuts] section.
S CESetupDLL:
setup_DLL
Optimal string that specifies a SETUP.DLL file. It is written by the Independent Software Vendor (ISV) and contains customized functions
for operations during installation and removal of the application. The
file must be specified in the [SourceDisksFiles] section.
S CESelfRegister:
self_reg_DLL_filename
String that identifies files that self-register by exporting the DllRegisterServer and DllUnregisterServer Component Object Model (COM)
functions. Specify these files in the [SourceDiskFiles] section. During
installation, if installation on the device fails to call the file’s exported
DllRegisterServer function, the file’s exported DllUnregisterServer
function will not be called during removal.
Example
[DefaultInstall]
AddReg = RegSettings.All
CEShortcuts = Shortcuts.All
[SourceDiskNames]
This section describes the name and path of the disk on which your application resides.
Required? Yes
S disk_ordinal:
disk_label,,path
1=,“App files” , C:\Appsoft\RP32\...
2=,“Font files”,,C:\RpTools\...
3=,“CE Tools” ,,C:\windows ce tools...
S CESignature:
“$Windows CE$”
Example
[SourceDisksNames]
1 = ,“Common files”,,C:\app\common
[SourceDisksNames.SH3]
2 = ,“SH3 files”,,sh3
[SourceDisksNames.MIPS]
2 = ,“MIPS files”,,mips
700 Series Color Mobile Computer User’s Manual
; Required section
; Using an absolute path
; Using a relative path
; Using a relative path
191
Chapter 7 — Programming
[SourceDiskFiles]
This describes the name and path of the files in which your application
resides.
Required? Yes
S filename:
disk_number[,subdir]
RPM.EXE = 1,c:\appsoft\...
WCESTART.INI = 1
RPMCE212.INI = 1
TAHOMA.TTF = 2
Note: [,subdir] is relative to the location of the INF file.
Example
[SourceDisksFiles]
; Required section
begin.wav = 1
end.wav = 1
sample.hlp = 1
[SourceDisksFiles.SH3]
sample.exe = 2
; Uses the SourceDisksNames.SH3 identification of 2.
[SourceDisksFiles.MIPS]
sample.exe = 2
; Uses the SourceDisksNames.MIPS identification of 2.
[DestinationDirs]
This describes the names and paths of the destination directories for the
application on the target device. Note Windows CE does not support directory identifiers.
Required? Yes
S file_list_section:
0,subdir
String that identifies the destination directory. The following list shows
the string substitutions supported by Windows CE. Use these only for
the beginning of the path. \
%CE1% \Program Files
%CE2% \Windows
%CE3% \My Documents
%CE4% \Windows\Startup
%CE5% \My Documents
%CE6% \Program Files\Accessories
%CE7% \Program Files\Communication
%CE8% \Program Files\Games
%CE9% \Program Files\Pocket Outlook
%CE10% \Program Files\Office
%CE11% \Windows\Start Menu\Programs
%CE12% \Windows\Start Menu\Programs\Accessories
%CE13% \Windows\Start Menu\Programs\Communications
%CE14% \Windows\Start Menu\Programs\Games
%CE15% \Windows\Fonts
%CE16% \Windows\Recent
%CE17% \Windows\Start Menu
%InstallDir%
192
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
Contains the path to the target directory selected during installation. It
is declared in the [CEStrings] section
%AppName%
Contains the application name defined in the [CEStrings] section.
Example
[DestinationDirs]
Files.Common = 0,%CE1%\My Subdir
Files.Shared = 0,%CE2%
; \Program Files\My Subdir
; \Windows
[CopyFiles]
This section, under the [DefaultInstall] section, describes the default files
to copy to the target device. Within the [DefaultInstall] section, files were
listed that must be defined elsewhere in the INF file. This section identifies that mapping and may contain flags.
Required? Yes
S copyfile_list_section:
destination_filename,[source_filename]
The source_filename parameter is optional if it is the same as destination_filename.
S copyfile_list_section:
flags
The numeric value that specifies an action to be done while copying files. The following table shows values supported by Windows CE.
Flag
Value
Description
COPYFLG_WARN_IF_SKIP
0x00000001 Warn user if skipping a file is attempted after error.
COPYFLG_NOSKIP
0x00000002 Do not allow a user to skip copying a file.
COPYFLG_NO_OVERWRITE
0x00000010 Do not overwrite files in destination directory.
COPYFLG_REPLACEONLY
0x00000400 Copy the source file to the destination directory only if the
file is already in the destination directory.
CE_COPYFLG_NO_DATE_DIALOG
0x20000000 Do not copy files if the target file is newer.
CE_COPYFLG_NODATECHECK
0x40000000 Ignore date while overwriting the target file.
CE_COPYFLG_SHARED
0x80000000 Create a reference when a shared DLL is counted.
Example
[DefaultInstall.SH3]
CopyFiles = Files.Common, Files.SH3
[DefaultInstall.MIPS]
CopyFiles = Files.Common, Files.MIPS
[AddReg]
This section, under the [DefaultInstall] section, is optional and describes
the keys and values that the .CAB file adds to the device registry. Within
the [DefaultInstall] section, a reference may have been made to this
section, such as “AddReg=RegSettings.All”. This section defines the
options for that setting.
Required? No
700 Series Color Mobile Computer User’s Manual
193
Chapter 7 — Programming
S add_registry_section: registry_root_string
String that specifies the registry root location. The following list shows
the values supported by Windows CE.
S HKCR
Same as HKEY_CLASSES_ROOT
S HKCU
Same as HKEY_CURRENT_USER
S HKLM
Same as HKEY_LOCAL_MACHINE
S add_registry_section: value_name
Registry value name. If empty, the “default” registry value name is used.
S add_registry_section: flags
Numeric value that specifies information about the registry key. The
following table shows the values that are supported by Window CE.
Flag
Value
Description
FLG_ADDREG_NOCLOBBER
0x00000002 If the registry key exists, do not overwrite it. Can be used
with any of the other flags in this table.
FLG_ADDREG_TYPE_SZ
0x00000000 REG_SZ registry data type.
FLG_ADDREG_TYPE_MULTI_SZ
0x00010000 REG_MULTI_SZ registry data type. Value field that follows
can be a list of strings separated by commas.
FLG_ADDREG_TYPE_BINARY
0x00000001 REG_BINARY registry data type. Value field that follows
must be a list of numeric values separated by commas, one
byte per field, and must not use the 0x hexadecimal prefix.
FLG_ADDREG_TYPE_DWORD
0x00010001 REG_DWORD data type. The noncompatible format in the
Win32 Setup .INF documentation is supported.
Example
AddReg = RegSettings.All
[RegSettings.All]
HKLM,%reg_path%,,0x00000000,alpha
HKLM,%reg_path%,test,0x00010001,3
HKLM,%reg_path%\new,another,0x00010001,6
;  = “alpha”
; Test = 3
; New\another = 6
[CEShortCuts]
This section, a Windows CE-specific section under the [DefaultInstall]
section, is optional and describes the shortcuts that the installation application creates on the device. Within the [DefaultInstall] section, a reference
may have been made to this section, such as “ShortCuts.All”. This section
defines the options for that setting.
Required? No
S shortcut_list_section:
shortcut_filename
String that identifies the shortcut name. It does not require the .LNK
extension.
S shortcut_list_section:
shortcut_type_flag
Numeric value. Zero or empty represents a shortcut to a file; any nonzero numeric value represents a shortcut to a folder.
194
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
S shortcut_list_section:
target_file_path
String value that specifies the destination location. Use the target file
name for a file, such as MyApp.exe, that must be defined in a file copy
list. For a path, use a file_list_section name defined in the [DestinationDirs] section, such as DefaultDestDir, or the %InstallDir% string.
S shortcut_list_section:
standard_destination_path
Optional string value. A standard %CEx% path or %InstallDir%. If no
value is specified, the shortcut_list_section name of the current section or
the DefaultDestDir value from the [DestinationDirs] section is used.
Example
CEShortcuts = Shortcuts.All
[Shortcuts.All]
Sample App,0,sample.exe
App,0,sample.exe,%InstallDir%
; Uses the path in DestinationDirs. Sample
; The path is explicitly specified.
Sample .INF File
[Version]
; Required section
Signature = “$Windows NT$”
Provider = “Intermec Technologies Corporation”
CESignature = “$Windows CE$”
;[CEDevice]
;ProcessorType =
[DefaultInstall]
; Required section
CopyFiles = Files.App, Files.Fonts, Files.BitMaps, Files.Intl,
Files.TelecomNcsCE, Files.Windows, Files.Import, Files.Export, Files.Work,
Files.Database, Files.WinCE AddReg = RegSettings.All ;CEShortcuts =
Shortcuts.All
[SourceDisksNames] ; Required section
1 = ,“App files” ,,c:\appsoft\...
2 = ,”Font files” ,,c:\WinNT\Fonts
3 = ,”CE Tools” ,,c:\windows ce tools\wce400\700ie\mfc\lib\x86
[SourceDisksFiles] ; Required section
rpm.exe
= 1,C:\Appsoft\program\wce400\WCEX86Rel700
wcestart.ini = 1
rpmce212.ini = 1
intermec.bmp = 1
rpmlogo.bmp = 1
rpmname.bmp = 1
import.bmp = 1
export.bmp = 1
clock.bmp = 1
printer.bmp = 1
filecopy.bmp = 1
readme.txt = 1
lang_eng.bin = 1
rpmdata.dbd = 1,database\wce1
tahoma.ttf = 2
mfcce212.dll = 3
olece212.dll = 3
olece211.dll = 1,c:\windows ce tools\wce400\NMSD61102.11\mfc\lib\x86
rdm45wce.dll = 1,c:\rptools\rdm45wce\4_50\lib\wce400\wcex86rel
picfmt.dll = 1,c:\rptools\picfmt\1_00\wce400\wcex86rel6110
700 Series Color Mobile Computer User’s Manual
195
Chapter 7 — Programming
fmtctrl.dll = 1,c:\rptools\fmtctrl\1_00\wce400\wcex86rel6110
ugrid.dll = 1,c:\rptools\ugrid\1_00\wce400\wcex86rel6110
simple.dll = 1,c:\rptools\pspbm0c\1_00\wce400\wcex86rel
psink.dll = 1,c:\rptools\psink\1_00\wce400\WCEX86RelMinDependency
pslpwce.dll =1,c:\rptools\pslpm0c\1_00\wce400\WCEX86RelMinDependency
npcpport.dll = 1,c:\rptools\cedk\212_03\installable drivers\printer\npcp
;dexcom.dll = 1,c:\rptools\psdxm0c\1_00\x86
ncsce.exe = 1,c:\rptools\ncsce\1_04
nrinet.dll = 1,c:\rptools\ncsce\1_04
[DestinationDirs] ; Required section
;Shortcuts.All = 0,%CE3% ; \Windows\Desktop
Files.App
= 0,%InstallDir%
Files.DataBase
= 0,%InstallDir%\DataBase
Files.BitMaps
= 0,%InstallDir%\Bitmaps
Files.Fonts
= 0,%InstallDir%\Fonts
Files.Intl
= 0,%InstallDir%\Intl
Files.TelecomNcsCE = 0,%InstallDir%\Telecom\NcsCE
Files.Windows
= 0,%InstallDir%\Windows
Files.Import
= 0,%InstallDir%\Import
Files.Export
= 0,%InstallDir%\Export
Files.Work
= 0,%InstallDir%\Work
Files.WinCE
= 0,\storage_card\wince
[CEStrings]
; Required section
AppName = Rp32
InstallDir = \storage_card\%AppName%
[Strings]
; Optional section
;[Shortcuts.All]
;Sample App,0,sample.exe
;Sample App,0,sample.exe,%InstallDir%
; Uses the path in DestinationDirs.
; The path is explicitly specified.
[Files.App]
rpm.exe,,,0
rpm.ini,rpmce212.ini,,0
mfcce212.dll,,,0
olece212.dll,,,0
olece211.dll,,,0
rdm45wce.dll,,,0
picfmt.dll,,,0
fmtctrl.dll,,,0
ugrid.dll,,,0
simple.dll,,,0
psink.dll,,,0
pslpwce.dll,,,0
npcpport.dll,,,0
;dexcom.dll,,,0
[Files.DataBase]
rpmdata.dbd,,,0
[Files.Fonts]
tahoma.ttf,,,0
[Files.BitMaps]
intermec.bmp,,,0
rpmlogo.bmp,,,0
rpmname.bmp,,,0
196
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
import.bmp,,,0
export.bmp,,,0
clock.bmp,,,0
printer.bmp,,,0
filecopy.bmp,,,0
[Files.Intl]
lang_eng.bin,,,0
[Files.TelecomNcsCE]
ncsce.exe,,,0
nrinet.dll,,,0
[Files.Windows]
readme.txt,,,0
[Files.Import]
readme.txt,,,0
[Files.Export]
readme.txt,,,0
[Files.Work]
readme.txt,,,0
[Files.WinCE]
wcestart.ini,,,0
[RegSettings.All]
HKLM,”SOFTWARE\Microsoft\Shell\AutoHide”,,0x00010001,1
; Autohide the taskbar HKLM,”SOFTWARE\Microsoft\Shell\OnTop”,,0x00010001,0
; Shell is not on top
HKLM,”SOFTWARE\Microsoft\Clock”,SHOW_CLOCK,0x00010001,0
; Clock is not on taskbar
Using Installation Functions in SETUP.DLL
SETUP.DLL is an optional file that enables you to perform custom operations during installation and removal of your application. The following
list shows the functions that are exported by SETUP.DLL.
Install_Init
Called before installation begins. Use this function to check the application version when reinstalling an application and to determine if a dependent application is present.
Install_Exit
Called after installation is complete. Use this function to handle errors that occur during application installation.
Uninstall_Init
Called before the removal process begins. Use this function to close the application, if the application is running.
Uninstall_Exit
Called after the removal process is complete. Use this function to save database information to a
file and delete the database and to tell the user where the user data files are stored and how to reinstall the application.
Note; Use [DefaultInstall] > CESelfRegister (page 191) in the .INF file to
point to SETUP.DLL.
700 Series Color Mobile Computer User’s Manual
197
Chapter 7 — Programming
After the CAB File Extraction
Cab files that need to cause a warm reset after cab extraction will need to
create the __RESETMEPLEASE__.TXT file in the “\Windows” directory.
The preferred method to create this file is within the DllMain portion of
the SETUP.DLL file. It looks like this:
#include
#include
#include
#include




// in the public SDK dir
#define IOCTL_TERMINAL_RESET CTL_CODE (FILE_DEVICE_UNKNOWN,FILE_ANY_ACCESS,
2050, METHOD_NEITHER)
BOOL APIENTRY DllMain( HANDLE h, DWORD reason, LPVOID lpReserved )
return TRUE;
} // DllMain
//************************************************************************
// $DOCBEGIN$
// BOOL IsProcessRunning( TCHAR * pname );
//
// Description: Get process table snapshot, look for pname running.
//
// Arguments: pname - pointer to name of program to look for.
// for example, app.exe.
//
// Returns: TRUE - process is running.
//
FALSE - process is not running.
// $DOCEND$
//************************************************************************
BOOL IsProcessRunning( TCHAR * pname )
HANDLE hProcList;
PROCESSENTRY32 peProcess;
DWORD thDeviceProcessID;
TCHAR lpname[MAX_PATH];
if ( !pname || !*pname ) return FALSE;
_tcscpy( lpname, pname );
_tcslwr( lpname );
hProcList = CreateToolhelp32Snapshot( TH32CS_SNAPPROCESS, 0 );
if ( hProcList == INVALID_HANDLE_VALUE ) {
return FALSE;
} // end if
memset( &peProcess, 0, sizeof(peProcess) );
peProcess.dwSize = sizeof(peProcess);
if ( !Process32First( hProcList, &peProcess ) ) {
CloseToolhelp32Snapshot( hProcList );
return FALSE;
} // end if
198
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
thDeviceProcessID = 0;
do {
_tcslwr( peProcess.szExeFile );
if ( _tcsstr( peProcess.szExeFile, lpname ) ) {
thDeviceProcessID = peProcess.th32ProcessID;
break;
} // end if
} while ( Process32Next( hProcList, &peProcess ) );
if ( ( GetLastError() == ERROR_NO_MORE_FILES ) && ( thDeviceProcessID == 0
) ) {
CloseToolhelp32Snapshot( hProcList );
return FALSE;
} // end if
CloseToolhelp32Snapshot( hProcList );
return TRUE;
} // IsProcessRunning
codeINSTALL_INIT Install_Init(
HWND hwndParent,
BOOL fFirstCall,
BOOL fPreviouslyInstalled,
LPCTSTR pszInstallDir )
return codeINSTALL_INIT_CONTINUE;
codeINSTALL_EXIT Install_Exit (
HWND hwndParent,
LPCTSTR pszInstallDir,
WORD cFailedDirs,
WORD cFailedFiles,
WORD cFailedRegKeys,
WORD cFailedRegVals,
WORD cFailedShortcuts )
HANDLE h;
TCHAR srcfile[MAX_PATH];
TCHAR dstfile[MAX_PATH];
if (cFailedDirs || cFailedFiles || cFailedRegKeys ||
cFailedRegVals || cFailedShortcuts)
return codeINSTALL_EXIT_UNINSTALL;
if ( IsProcessRunning( L”autocab.exe” ) )
h = CreateFile( L”\\Windows\\__resetmeplease__.txt”,
(GENERIC_READ | GENERIC_WRITE), 0, NULL, CREATE_ALWAYS,
FILE_ATTRIBUTE_HIDDEN, NULL );
if ( h != INVALID_HANDLE_VALUE )
CloseHandle( h );
else
// Couldn’t create the file. If it failed because the file already
700 Series Color Mobile Computer User’s Manual
199
Chapter 7 — Programming
exists, it is not fatal.
// Otherwise, notify user of the inability to reset the device and they
will have to
// perform it manually after all of the installations are complete.
} // end if
else
DWORD dret;
h = CreateFile( L”SYI1:”,
(GENERIC_WRITE | GENERIC_READ), 0, NULL, OPEN_EXISTING,
FILE_ATTRIBUTE_NORMAL, NULL );
// Force a warm start NOW.
if ( h != INVALID_HANDLE_VALUE )
DeviceIoControl( h, IOCTL_TERMINAL_RESET, NULL, 0, NULL, 0, &dret,
NULL);
// Won’t return, but we’ll show clean up anyway
CloseHandle( h );
else
// Couldn’t access SYSIO. Notify user.
} // end if
} // end if
return codeINSTALL_EXIT_DONE;
codeUNINSTALL_INIT
Uninstall_Init(
HWND hwndParent,
LPCTSTR pszInstallDir ) {
// TODO: Perform the reverse of INSTALL_INIT here
return codeUNINSTALL_INIT_CONTINUE;
codeUNINSTALL_EXIT
Uninstall_Exit(HWND hwndParent) {
// TODO: Perform the reverse of INSTALL_EXIT here
return codeUNINSTALL_EXIT_DONE;
The system software looks for the following directory structure and files on
the installed media card whether it be a Secure Digital storage card or
CompactFlash storage card or embedded flash file system. No other folders
need exist.
\2577\autorun.exe
\2577\autorun.dat
\2577\autocab.exe
\2577\autocab.dat
\cabfiles\*.cab
200
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
Creating CAB Files with CAB Wizard
After you create the .INF file and the optional SETUP.DLL file, use the
CAB Wizard to create the .CAB file. Below is the command-line syntax:
cabwiz.exe “inf_file” [/dest dest_directory] [/err error_file] [/cpu cpu_type
[cpu_type]]
A batch file in  directory, with these commands, works well:
cabwiz.exe c:\appsoft\\
cd \appsoft\
“inf_file”
The SETUP.INF file path.
dest_directory
The destination directory for the .CAB files. If no directory is specified, the .CAB files are created
in the “inf_file” directory.
error_file
File name for a log file that contains all warnings and errors that are encountered when the .CAB
files are compiled. If no file name is specified, errors are displayed in message boxes. If a file name
is used, the CAB Wizard runs without the user interface (UI); this is useful for automated builds.
cpu_type
Creates a .CAB file for each specified microprocessor tag, which is a label used in the Win32 SETUP.INF file to differentiate between different microprocessor types. The /cpu parameter, followed by multiple cpu_type values, must be the last qualifier in the command line.
Example
This example creates .CAB files for the ARM and MIPS microprocessors,
assuming the Win32 SETUP.INF file contains the ARM and MIPS tags:
cabwiz.exe “c:\myfile.inf” /err myfile.err /cpu arm mips
Note: CABWIZ.EXE, MAKECAB.EXE, and CABWIZ.DDF (Windows
CE files available on the Windows CE Toolkit) must be installed in the
same directory on the desktop computer. Call CABWIZ.EXE using its full
path for the CAB Wizard application to run correctly.
Troubleshooting the CAB Wizard
To identify and avoid problems that might occur when using the CAB
Wizard, follow these guidelines:
S Use %% for a percent sign (%) character when using this character in
an .INF file string, as specified in Win32 documentation. This will not
work under the [Strings] section.
S Do not use .INF or .CAB files created for Windows CE to install applications on Windows-based desktop platforms.
S Ensure the MAKECAB.EXE and CABWIZ.DDF files, included with
Windows CE, are in the same directory as CABWIZ.EXE.
S Use the full path to call CABWIZ.EXE.
S Do not create a .CAB file with the MAKECAB.EXE file included with
Windows CE. You must use CABWIZ.EXE, which uses
MAKECAB.EXE to generate the .CAB files for Windows CE.
S Do not set the read-only attribute for .CAB files.
700 Series Color Mobile Computer User’s Manual
201
Chapter 7 — Programming
Customization and Lockdown
Pocket PC (Windows Mobile) is a hardware specification created by
Microsoft Corporation. Devices that wish to carry the Pocket PC logo
must meet the minimum hardware requirements set in the Pocket PC specification. Manufacturers are free to add extra hardware functionality.
Pocket PC devices also use a specialized version of the CE operating system. This operating system is built from Windows CE 4.2 but contains
customizations, most notably the lack of a desktop and the addition of the
Today Screen.
To carry the Pocket PC logo, all devices must be tested at an Independent
Test Laboratory. The ITL testing is done based on Microsoft requirements. The test lab then reports the findings back to Microsoft Corporation and Intermec. If the 700 Color Computer passed all tests, Intermec is
allowed to ship the device with the Pocket PC logo. Each time the operating system is modified, Intermec must resubmit to ITL testing.
This means we cannot change the operating system much and still be a
Pocket PC device. For example, if we remove Word from the Start menu,
the device would fail ITL testing and we would not be able to ship devices
with the Pocket PC logo.
Although many customers want a Pocket PC device, some customers
would prefer that their users not have access to all of the Pocket PC features. Intermec cannot customize the operating system in any way but a custom application can:
Delete items from the Start menu, and Programs folder. These items are just shortcuts in the file system so the application is not really being deleted. Cold booting the device will bring these items back so the application will need
to be run on every cold boot.
Use the RegFlushKey() API to save a copy of the registry to a storage device. See the 700 Color Management Tools
portion for more information on how to do this. Saving a copy of the registry restores most system settings in a cold
boot situation.
Use the SHFullScreen() API in conjunction with other APIs to make the application take up the entire display and
prevent the start menu from being available.
Remap keys and disable keys on the keypad.
Create a custom SIP.
Make changes to the registry to configure the device.
Should you want your 700 Color Computer to display a full screen, keep
in mind that your computer is Pocket-PC certified by Microsoft Corporation. Check out resources on programming for the Pocket PC, using the
following links. These give full instructions on how to display full screen.
S Instructions on how to create a full screen application for eVC++ applications using an SHFullScreen() API:
support.microsoft.com/support/kb/articles/Q266/2/44.ASP
S Instructions on how to create a full screen application for eVB applications also using the SHFullScreen() API:
support.microsoft.com/support/kb/articles/Q265/4/51.ASP
202
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
FTP Server
FTP support is provided through the FTP Server application
FTPDCE.EXE (MS Windows CE Versions) which is provided as part the
base system.
FTPDCE is the Internet File Transfer Protocol (FTP) server process. The
server can be invoked from an application or command line. Besides servicing FTP client requests the FTP Server also send a “network announcement” to notify prospective clients of server availability.
Note: You should consult the RFC959 specification for proper use of
some of these commands at the following URL:
S www.ietf.org/rfc/rfc959.txt for the text version, or
S www.w3.org/Protocols/rfc959/ for an html version
Do the following to send commands:
1 Start an FTP client and connect to the device FTP server.
2 Log in with “intermec” as the user name and “cr52401” - the password.
3 From the FTP client, send the command.
4 Wait for a response.
Synopsis
ftpdce [ options ]
Options
–Aaddr
(where addr is in the form of a.b.c.d) Sets the single target address to which to send the network announcement. Default is broadcast.
–Bbyte
Sets the FTP data block size. Smaller sizes may be useful over slower links. Default is 65536.
–Cname
Sets the device name. Used by Intermec management software.
–Fvalue
Disables the default Intermec account. A value of “0” disables the account. Default is “1”.
Note that disabling the default account without providing a working access control list on the server
will result in a device that will not accept any FTP connections.
–Hsec
Sets the interval between network announcements in seconds.A value of “0” turns the network announcement off. Default is 30 seconds.
–Iaddr
(where addr is in the form of a.b.c.d) Sets the preferred 6920 Communications Server (optional).
–Llog
(where log is either “0” or “1”) Sets the state of logging. Default is 0 (disabled).
–Nsec
Specifies the number of seconds to wait before initially starting FTP server services.
–Pport
Sets the UDP port on which the network announcement will be sent. Default port is 52401.
–Qport
Sets the port on which the FTP Server will listen for connections. Default port is 21.
–Rdir
Sets the FTP mount point to this directory. Default is the root folder of the object store.
–Tscrip
Sets the script name for the 6920 Communications Server to process.
–Uurl
Sets the default URL for this device.
–Z“parms”
Sets extended parameters to be included in the network announcement.
700 Series Color Mobile Computer User’s Manual
203
Chapter 7 — Programming
Configurable Parameters Via the Registry Editor
These parameters receive default values during the Intermec FTP Server
component installation. Few of the parameters are visible in the registry by
default, but most must be created to modify the FTP server behavior.
BlockSize
Setting this parameter configures the Intermec FTP Server to transmit and
receive Ethernet packets using the specified data block size. By default, the
FTP server transmits and receives data using a 64K data block size. Adjusting this value may be useful in certain wireless TCP/IP installations.
Key
HKLM\Software\Intermec\IFTP
Value Type
REG_DWORD - data block size, in bytes.
Valid Range
0x100-0x10000 (256-65536 decimal).
Default
65536
DeviceName
This configures the Intermec FTP Server to include the specified device
name in the Intermec Device Network Announcement (IDNA). Adjusting
this value may assign a symbolic name to this device for asset tracking.
Key
HKLM\Software\Intermec\IFTP
Value Type
REG_SZ
Valid Range
None.
Default
None.
DeviceURL
This parameter configures the Intermec FTP Server to transmit the specified URL in the IDNA. This can be used by Intermec management software for asset management.
Key
HKLM\Software\Intermec\IFTP
Value Type
REG_SZ
Valid Range
None.
Default
None.
IDNATarget
This parameter configures the Intermec FTP Server to transmit the IDNA
to a specific destination instead of a general UDP broadcast. This parameter is useful on networks that do not allow UDP broadcasts to be routed
between subnets. The use of this parameter restricts the reception of the
IDNA to the target destination only.
204
Key
HKLM\Software\Intermec\IFTP
Value Type
REG_SZ
Valid Range
None.
Default
None.
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
ManifestName
This parameter configures the Intermec FTP Server to transmit the specified manifest name in the IDNA. This parameter is used by the Intermec
6920 Communications Server for communication transactions. See the
6920 Server documentation for proper use of this parameter.
Key
HKLM\Software\Intermec\IFTP
Value Type
REG_SZ
Valid Range
None.
Default
iftp.ini
PauseAtStartup
This configures the Intermec FTP Server to sleep for the specified number
of seconds before making the FTP service available on the device.
Key
HKLM\Software\Intermec\IFTP
Value Type
REG_DWORD - stored in seconds.
Valid Range
None.
Default
Root
This parameter configures the Intermec FTP Server to set the root of the
FTP mount point to the specified value. Note that this must map to an existing directory or you will not be able to log into the FTP Server.
Key
HKLM\Software\Intermec\IFTP
Value Type
REG_SZ
Valid Range
None.
Default
Transferring Files Over TCP/IP Networks
The File Transfer Protocol (FTP) server transfers files over TCP/IP networks. The FTPDCE.EXE program is a version that does not display a
window, but can run in the background.
FTPDCE is the Internet File Transfer Protocol (FTP) server process. The
server can be invoked from an application or command line. Besides servicing FTP client requests, the FTP Server also sends a “network announcement” to notify prospective clients of server availability.
Remarks
The FTP Server currently supports the following FTP requests:
CDUP
Changes to the parent directory of the current working directory.
CWD
Changes working directory.
700 Series Color Mobile Computer User’s Manual
205
Chapter 7 — Programming
DELE
Deletes a file.
HELP
Gives help information.
LIST
(This FTP request is the same as the ls -lgA command). Gives list files in a directory.
MKD
Makes a directory.
MODE
(Always Uses Binary). Specifies data transfer mode.
NLST
(Not supported) Gives a name list of files in directory (this FTP request is the same as the ls command).
NOOP
Does nothing.
PASS
Specifies a password.
PWD
Prints the current working directory.
QUIT
Terminates session.
RETR
Retrieves a file.
RMD
Removes a directory.
RNFR
Specifies rename-from file name.
RNTO
Specifies rename-to file name.
STOR
Stores a file.
SYST
Shows the operating system type of server system.
TYPE
(Binary transfers only.) Specifies the data transfer type with the Type parameter.
USER
Specifies user name.
XCUP
(Not Normally Used) Changes the parent directory of the current working directory.
XCWD
(Not Normally Used) Changes the current directory.
XMKD
(Not Normally Used) Creates a directory.
XPWD
(Not Normally Used) Prints the current working directory.
XRMD
(Not Normally Used) Removes a directory.
SITE
The following extended OEM commands are supported by the SITE request. For Microsoft FTP clients, you can send site commands by preceding the command with “quote” such as “quote site status.”
ATTRIB
Gets or sets the attributes of a given file. (SITE ATTRIB)
Usage
QUOTE SITE ATTRIB [+R | -R] [+A | -A ] [+S | -S] [+H | -H] [[path]
filename]
+ Sets an attribute.
– Clears an attribute.
R Read-only file attribute.
A Archive file attribute.
S System file attribute.
H Hidden file attribute.
To retrieve the attributes of a file, only specify the file. The server response will be:
200-AD SHRCEIX filename
206
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
If the flag exists in its position shown previously, it is set. Also, in addition to the
values defined above, there is also defined:
C Compressed file attribute.
E Encrypted file attribute.
I INROM file attribute.
X XIP file attribute (execute in ROM, not shadowed in RAM).
BOOT
Reboots the server OS. This will cause the system on which the server is executing to
reboot. The FTP Server will shut down cleanly before reboot. All client connections
will be terminated. Cold boot is default except for the PocketPC build in which the
default is warm boot. (SITE BOOT)
Usage:
COPY
QUOTE SITE BOOT [WARM | COLD]
Copies a file from one location to another. (SITE COPY)
Usage:
QUOTE SITE COPY [source] [destination]
Example: QUOTE SITE COPY ‘\Storage Card\one.dat’ ‘\Storage Card\two.dat’
EXIT
Exits the FTP Server. This command will shut down the FTP Server thus terminating all client connections. (SITE EXIT)
Usage:
HELP
Gives site command help information. (SITE HELP)
Usage:
KILL
QUOTE SITE LOG [open [filename]| close]
Lists the running processes (SITE PLIST)
Usage:
RUN
QUOTE SITE KILL [program | pid]
Opens or closes the program log. (SITE LOG)
Usage:
PLIST
QUOTE SITE HELP [command]
Terminates a running program. (SITE KILL)
Usage:
LOG
QUOTE SITE EXIT
QUOTE SITE PLIST
Starts a program running. If the program to run has spaces in path or filename,
wrapping the name with single quotes is required.
Usage:
QUOTE SITE RUN [program]
Example: QUOTE SITE RUN ‘\Storage Card\app.exe’
STATUS
Returns the current settings of the FTP Server. MAC, serial number, model, IP address, network announcement information as well as OS memory usage are returned.
(SITE STATUS)
Usage:
TIMEOUT
Toggles idle timeout between 120 to 1200 seconds (2 to 20 minutes). If this timer
expires with no activity between the client and the server, the client connection will
be disconnected. If the optional seconds argument is supplied, the server will set the
connection timeout to the number of seconds specified. Default is 120 seconds or 2
minutes. (SITE TIMEOUT)
Usage:
EKEY
QUOTE SITE TIMEOUT [seconds]
Gives site command electronic key information. (SITE HELP)
Usage:
EVAL
QUOTE SITE STATUS
QUOTE SITE EKEY [command]
Gives site command electronic value information. (SITE HELP)
Usage:
QUOTE SITE EVAL [command]
700 Series Color Mobile Computer User’s Manual
207
Chapter 7 — Programming
GVAL
Gives site command general value information. (SITE HELP)
Usage:
PVAL
QUOTE SITE GVAL [command]
Gives site command value information. (SITE HELP)
Usage:
QUOTE SITE PVAL [command]
The remaining FTP requests specified in RFC 959 are recognized, but not
implemented.
The banner returned in the parenthetical portion of its greeting shows the
version number of the FTP Server as well as the MAC address, serial number and operating system of the machine hosting the server.
The FTP Server supports browsing from the latest Netscape and Microsoft
web browsers. Drag-and-drop capability is available using this environment.
The FTPDCMDS subdirectory contains commands to use from the web
browser.
S Click EXITME.BIN to execute a SITE EXIT command.
S Click REBOOTME.BIN to execute SITE BOOT command.
S Use the GET command on these files to have the FTP Server execute
these commands.
S Security:
A customer configurable access control list may be installed on the
700 Color Computer. This list will allow customers to restrict access
via the FTP Server to users they wish and is in addition to default
Intermec accounts that are disabled using the -F0 option at runtime.
The access control list is named FTPDCE.TXT and is placed in the
same directory on the 700 Color Computer as the FTPDCE.EXE
server. The FTP Server encrypts this file to keep the information safe
from unauthorized users. This file is encrypted when the FTP Server
is started so a file that is placed onto the 700 Color Computer after
the FTP Server starts will require a restart of the FTP Server to take
effect.
The format of the FTPDCE.TXT is as follows:
FTPDCE:user1!passwd1user2!passwd2user3
!passwd3...
Note: The user accounts and passwords are case sensitive.
Once the access control list is encrypted on the 700 Color Computer,
the FTP Server hides this file from users. Once an access control list
is installed on the 700 Color Computer, a new one is not accepted by
the FTP Server until the previous one is removed. Encrypted access
control lists are not portable between 700 Color Computers.
Stopping the FTP Server from Your Application
To allow application programmers the ability to programmatically shut
down the FTP Server, the FTP Server periodically tests to see if a named
event is signaled. ITC_IFTP_STOP is the name of this event.
208
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
For examples on how to use events, consult the Microsoft Developer Network Library at www.msdn.com. The MSDN Library is an essential resource for developers using Microsoft tools, products, and technologies. It
contains a bounty of technical programming information, including sample code, documentation, technical articles, and reference guides.
Autostart FTP
This automatically starts the FTP Server (FTPDCE.EXE) when the 700
Color Computer is powered on. This is provided with the NDISTRAY
program (the Network Driver Interface Specification tray application),
which displays the popup menu that currently allows you to load and unload the network drivers. Tap the antenna icon in the System Tray of the
Today screen (a sample antenna icon is circled below) for this pop-up menu.
The default is to start the FTP Server at boot time, unless the following
registry entry is defined and set to “0” which disables AutoFTP. “1” enables the AutoFTP. The entry can be set from the NDISTRAY pop-up
menu by selecting either AutoFTP On or AutoFTP Off.
HKEY_LOCAL_MACHINE\Software\Intermec\Ndistray\StartupIFTP
These new entries are located below the selections to load the network
drivers. If the StartupIFTP registry key is not defined, the FTP Server is
loaded by default, to provide “out-of-the-box” capability for customers
who want to begin loading files to the 700 Color Computer without any
prior configuration.
Note: If a network driver is unloaded using the NDISTRAY popup menu,
and the FTP Server is running, the FTP Server is stopped.
On a resume, if AutoFTP is enabled and the FTP Server is running, it is
stopped and restarted. NDISTRAY uses a helper application named
RESETIFTP to implement the restart on resume feature.
700 Series Color Mobile Computer User’s Manual
209
Chapter 7 — Programming
To do an AutoFTP Installation Check:
1 Ensure the FTP Server is running “out-of-the-box” the first time.
2 Tap Start > Today to access the Today screen, then tap the antenna
icon in the System Tray to bring up the NDISTRAY pop-up menu.
Select AutoFTP Off to disable AutoFTP. Do a warm boot and confirm
the FTP Server is not running.
3 Tap Start > Today to access the Today screen, then tap the antenna
icon in the System Tray to bring up the NDISTRAY pop-up menu.
Select AutoFTP On to enable AutoFTP, reboot, confirm it is running.
4 Unload the network driver when the FTP Server is running and confirm that it is not running any more.
5 Load the FTP Server, establish a connection, then suspend and resume.
The server should still run, but the FTP connection to the client should
be dropped.
Kernel I/O Controls
This describes the KernelIoControl() functions available to application
programmers. Most C++ applications will need to prototype the function
as the following to avoid link and compile errors.
extern “C” BOOL KernelIoControl(DWORD dwIoControlCode, LPVOID lpInBuf, DWORD
nInBufSize, LPVOID lpOutBuf, DWORD nOutBufSize, LPDWORD lpBytesReturned);
You can also see the Device Resource Kit in the Intermec Developer Library (IDL) for information about these functions. The IDL is available as
a download from the Intermec web site at www.intermec.com/idl. Contact
your Intermec representative for more information.
IOCTL_HAL_GET_DEVICE_INFO
This IOCTL returns either the platform type or the OEMPLATFORM
name based on an input value.
Syntax
BOOL KernelIoControl( IOCTL_HAL_GET_DEVICE_INFO, LPVOID lpInBuf, DWORD
nInBufSize, LPVOID lpOutBuf, DWORD nOutBufSize, LPDWORD lpBytesReturned );
210
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
Parameters
lpInBuf
Points to a DWORD containing either the
SPI_GETPLATFORMTYPE or SPI_GETOEMINFO value.
lpInBufSize
Must be set to sizeof(DWORD).
lpOutBuf
Must point to a buffer large enough to hold the return data of the
function. If SPI_GETPLATFORMTYPE is specified in lpInBuf,
then the “PocketPC\0” Unicode string is returned. If SPI_GETOEMINFO is specified in lpInBuf, then the “Intermec 700\0”
Unicode string is returned.
nOutBufSize
The size of lpOutBuf in bytes. Must be large enough to hold the
string returned.
lpBytesReturned
The actual number of bytes returned by the function for the data
requested.
Return Values
Returns TRUE if function succeeds. Returns FALSE if the function fails.
GetLastError() may be used to get the extended error value.
IOCTL_HAL_ITC_READ_PARM
Usage
#include “oemioctl.h”
Syntax
BOOL KernelIoControl( IOCTL_HAL_ITC_READ_PARM,LPVOID lpInBuf,DWORD
nInBufSize,LPVOID lpOutBuf,DWORD nOutBufSize,LPDWORD lpBytesReturned );
Parameters
lpInBuf
Points to this structure. See “ID Field Values” below.
struct PARMS {
BYTE id;
BYTE ClassId;
};
nInBufSize
Must be set to the size of the PARMS structure.
lpOutBuf
Must point to a buffer large enough to hold the return data of the
function. If this field is set to NULL and nOutBufSize is set to zero
when the function is called the function will return the number
bytes required by the buffer.
nOutBufSize
The size of lpOutBuf in bytes.
lpBytesReturned
Number of bytes returned by the function for the data requested.
Return Values
Returns TRUE if function succeeds. Returns FALSE if the function fails.
GetLastError() may be used to get the error value. Either
ERROR_INVALID_PARAMETER or
ERROR_INSUFFICIENT_BUFFER may be returned when this function
is used to get the error.
700 Series Color Mobile Computer User’s Manual
211
Chapter 7 — Programming
ID Field Values
The id field of the PARMS structure may be one of the following values:
ID Field Values
ITC_NVPARM_ETHERNET_ID
Returns Ethernet 802.11b or 802.11b/g MAC Address. Six bytes returned in buffer pointed to by lpOutBuffer
ITC_NVPARM_SERIAL_NUM
Returns serial number of device in BCD format. Six bytes returned in buffer pointed to by lpOutBuffer
ITC_NVPARM_MANF_DATE
Returns device manufacture date in BCD YYYY/MM/DD format. 4 bytes sent in buffer pointed to by lpOutBuffer
ITC_NVPARM_SERVICE_DATE
Returns last device service date in BCD YYYY/MM/DD format. Four bytes sent in buffer pointed to by lpOutBuffer
ITC_NVPARM_DISPLAY_TYPE
Returns device display type. One byte returned in buffer pointed to by lpOutBuffer
ITC_NVPARM_EDG_IP
Returns device Ethernet debug IP address. Four bytes returned in buffer pointed to by lpOutBuffer
ITC_NVPARM_EDBG_SUBNET
Returns device Ethernet debug subnet mask. Four bytes returned in buffer pointed to by lpOutBuffer
ITC_NVPARM_ECN
Returns ECNs applied to device in bit array format. Four bytes returned in buffer pointed to by lpOutBuffer
ITC_NVPARM_CONTRAST
Returns device default contrast setting. Two bytes returned in buffer pointed to by lpOutBuffer
ITC_NVPARM_MCODE
Returns manufacturing configuration code for device. Sixteen bytes returned in buffer pointed to by lpOutBuffer
ITC_NVPARM_VERSION_NUMBER
Returns firmware version for various system components. These values for ClassId field of PARMS structure are
allowed when ITC_NVPARM_VERSION_NUMBER used in id field:
S VN_CLASS_KBD Returns five-byte string, including null terminator, with ASCII value representing keypad
microprocessor version in system. String format is x.xx with terminating null character.
S VN_CLASS_ASIC Returns five-byte string, including null terminator, with ASCII value representing version of
FPGA firmware in system. String format is x.xx with terminating null character.
S VN_CLASS_BOOTSTRAP Returns five-byte string, including null terminator, with ASCII value representing
version of Bootstrap Loader firmware in system. String format is x.xx with terminating null character.
ITC_NVPARM_INTERMEC_SOFTWARE_CONTENT
Reads manufacturing flag bits from non-volatile data store dictating certain software parameters. BOOLEAN
DWORD returned in buffer pointed to by lpOutBuffer indicating whether Intermec Content enabled in XIP
regions. TRUE indicates enabled. FALSE is not enabled.
ITC_NVPARM_ANTENNA_DIVERSITY
Reads state of antenna diversity flag. BOOLEAN DWORD returned in buffer pointed to by lpOutBuffer indicating
whether diversity antenna is installed. TRUE indicates installed. FALSE is not installed.
ITC_NVPARM_WAN_RI
Reads state of WAN ring indicator flag. BOOLEAN DWORD returned in buffer pointed to by lpOutBuffer
indicating polarity of WAN RI signal. TRUE indicates active high. FALSE is active low.
ITC_NVPARM_RTC_RESTORE
Reads state of real-time clock restore flag. BOOLEAN DWORD returned in buffer pointed to by lpOutBuffer.
TRUE indicates RTC is restored on cold-boot. FALSE is RTC is not restored.
ITC_NVPARM_INTERMEC_DATACOLLECTION_SW
Reads state of data collection software enabled flag. BOOLEAN DWORD returned in buffer pointed to by
lpOutBuffer indicating data collection software installs at boot time. FALSE is do not install data collection software
212
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
ID Field Values (continued)
ITC_NVPARM_INTERMEC_DATACOLLECTION_HW
Reads data collection hardware flags. BYTE returned in buffer pointer to by lpOutBuffer indicating type of data
collection hardware installed. Maximum value returned is ITC_DEVID_SCANHW_MAX:
S ITC_DEVID_SCANHW_NONE No scanner hardware installed.
S ITC_DEVID_OEM2D_IMAGER OEM 2D imager installed.
S ITC_DEVID_INTERMEC2D_IMAGER Intermec 2D imager installed.
S ITC_DEVID_SE900_LASER SE900 laser installed.
S ITC_DEVID_SE900HS_LASER SE900HS laser installed.
S ITC_DEVID_INTERMEC_EVIO EVIO linear imager installed.
High bit non-zero value indicates S6 scanning engine is installed. Bit mask is ITC_DEVID_S6ENGINE_MASK.
ITC_NVPARM_WAN_INSTALLED
Reads state of WAN radio installed flag. BOOLEAN DWORD is returned in buffer: TRUE = WAN radio installed.
ITC_NVPARM_WAN_FREQUENCY
Reads state of WAN radio frequency flag. BOOLEAN DWORD is returned in buffer: TRUE indicates WAN radio
frequency is United States. FALSE is a European WAN radio frequency.
ITC_NVPARM_WAN_RADIOTYPE
Reads WAN radio ID installed by manufacturing. BYTE returned in buffer pointer to by lpOutBuffer indicating type
of WAN radio hardware installed. Maximum value returned is ITC_DEVID_WANRADIO_MAX:
S ITC_DEVID_WANRADIO_NONE No WAN radio installed
S ITC_DEVID_WANRADIO_SIERRA_SB555 CDMA Sierra Wireless radio
S ITC_DEVID_WANRADIO_XIRCOM_GEM3503 GSM/GPRS Intel (Xircom) radio
S ITC_DEVID_WANRADIO_SIEMENS_MC45 GSM/GPRS Siemens radio
S ITC_DEVID_WANRADIO_SIEMENS_MC46 GSM/GPRS Siemens radio
ITC_NVPARM_80211_INSTALLED
Reads state of 802.11b or b/g radio installed flag. BOOLEAN DWORD returned in buffer: TRUE = radio installed.
ITC_NVPARM_80211_RADIOTYPE
Reads 802.11b or b/g radio ID installed by manufacturing. BYTE returned in buffer pointer to by lpOutBuffer
indicates type of radio hardware installed. ITC_DEVID_80211RADIO_MAX is maximum value returned:
S ITC_DEVID_80211RADIO_NONE No 802.11b or 802.11b/g radio installed.
S ITC_DEVID_80211RADIO_INTEL_2011B Intel 2011B radio installed.
ITC_NVPARM_BLUETOOTH_INSTALLED
Reads state of Bluetooth radio installed flag. BOOLEAN DWORD returned in buffer pointed to by lpOutBuffer.
TRUE indicates Bluetooth radio installed. FALSE is no Bluetooth radio installed.
ITC_NVPARM_SERIAL2_INSTALLED
Reads state of serial 2 (COM2) device installed flag. BOOLEAN DWORD returned in buffer pointed to by
lpOutBuffer. TRUE indicates serial 2 device is installed. FALSE is no serial 2 device is installed.
ITC_NVPARM_VIBRATE_INSTALLED
Reads state of vibrate device installed flag. BOOLEAN DWORD is returned in buffer pointed to by lpOutBuffer.
TRUE indicates vibrate device is installed. FALSE is no vibrate device is installed.
ITC_NVPARM_LAN9000_INSTALLED
Reads state of Ethernet device installed flag. BOOLEAN DWORD is returned in buffer pointed to by lpOutBuffer.
TRUE indicates Ethernet device is installed. FALSE is no Ethernet device is installed.
ITC_NVPARM_SIM_PROTECT_HW_INSTALLED
Reads state of SIM card protection hardware installed flag. BOOLEAN DWORD returned in buffer pointed to by
lpOutBuffer. TRUE indicates SIM card protection hardware installed. FALSE is no such hardware installed.
ITC_NVPARM_SIM_PROTECT_SW_INSTALLED
Reads state of SIM card protection software installed flag. BOOLEAN DWORD returned in buffer pointed to by
lpOutBuffer. TRUE indicates SIM card protection software is installed. FALSE is no such software installed.
700 Series Color Mobile Computer User’s Manual
213
Chapter 7 — Programming
IOCTL_HAL_ITC_WRITE_SYSPARM
Describes and enables the registry save location.
Usage
#include “oemioctl.h”
Syntax
BOOL KernelIoControl( IOCTL_HAL_ITC_WRITE_SYSPARM,LPVOID lpInBuf,DWORD
nInBufSize, LPVOID lpOutBuf, DWORD nOutBufSize, LPDWORD lpBytesReturned );
Parameters
lpInBuf
A single byte that may be one of the id values. See “ID Field Values”
on the next page.
nInBufSize
Must be set to the size of the lpInBuf in bytes.
lpOutBuf
Must point to a buffer large enough to hold the data to be written
to the non-volatile data store.
nOutBufSize
The size of lpOutBuf in bytes.
lpBytesReturned
The number of bytes returned by the function.
Return Values
Returns TRUE if function succeeds. Returns FALSE if the function fails.
GetLastError() may be used to get the error value. Either
ERROR_INVALID_PARAMETER or
ERROR_INSUFFICIENT_BUFFER may be returned when this function
is used to get the error.
ID Field Values
The id field of lpInBuf may be one of the following values:
ID Field Values
ITC_REGISTRY_SAVE_ENABLE
Enables or disables the save registry to non-volatile media feature of the RegFlushKey() function. lpOutBuf must be
set to zero (FALSE) if the feature is to be disabled or one (TRUE) if the feature is to be enabled.
ITC_ DOCK_SWITCH
This IOCTL sets a position of the dock switch. The dock switch may be set to either “modem” or “serial” positions.
lpOutBuf must point to a buffer that contains a byte value of either DOCK_MODEM or DOCK_SERIAL as
defined in OEMIOCTL.H; the value specifies the position the switch is to be set. The call appears as follows:
// port = DOCK_MODEM or DOCK_SERIAL as defined in oemioctl.h
BOOL SetDockSwitch( BYTE port)
DWORD cmd = ITC_DOCK_SWITCH;
DWORD cbRet;
return KernelIoControl(IOCTL_HAL_ITC_WRITE_SYSPARM,&cmd, sizeof(cmd),
&port,sizeof(port),&cbRet)
214
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
ID Field Values (continued)
ITC_ WAKEUP_MASK
This IOCTL sets a bit mask that represents the mask for the five programmable wakeup keys. The I/O key is not a
programmable wakeup key. By default it is always the system resume key and all other keys are set to disable key
wakeup. A zero in a bit position masks the wakeup for that key. A one in a bit position enables wakeup for that key.
lpOutBuf must point to a buffer that contains a byte value of a wakeup mask consisting of the OR’ed constants as
defined in OEMIOCTL.H. Only the following keys are programmable as wakeup events.
#define SCANNER_TRIGGER 1
#define SCANNER_LEFT
#define SCANNER_RIGHT
#define GOLD_A1
#define GOLD_A2
0x10
ITC_AMBIENT_KEYBOARD (does not apply to the 730 Computer)
This IOCTL sets the threshold for the keypad ambient sensor. This can be a value from 0 (always off) to 255 (always
on). lpOutBuf must point to a buffer that contains a byte value of the desired setting.
ITC_AMBIENT_FRONTLIGHT (does not apply to the 730 Computer)
This IOCTL sets the threshold for the frontlight ambient sensor. This can be a value from 0 (always off) to 255.
lpOutBuf must point to a buffer that contains a byte value of the desired setting.
IOCTL_HAL_GET_DEVICEID
This returns the device ID. There are two types of device IDs supported,
which are differentiated based on the size of the output buffer. The UUID
is returned if the buffer size is set to sizeof(UNIQUE_DEVICEID), otherwise the oldstyle device ID is returned.
Usage
#include “pkfuncs.h”
#include “deviceid.h”
Syntax
BOOL KernelIoControl( IOCTL_HAL_GET_DEVICEID,LPVOID lpInBuf,DWORD
nInBufSize,LPVOID lpOutBuf,DWORD nOutBufSize,LPDWORD lpBytesReturned );
Parameters
lpInBuf
Should be set to NULL. STRICT_ID settings are not supported.
lpInBufSize
Should be set to zero.
lpOutBuf
Must point to a UNIQUE_DEVICEID structure as defined by
DEVICEID.H if the UUID is to be returned
nOutBufSize
The size of the UNIQUE_DEVICEID in bytes if the UUID is to
be returned. A DEVICE_ID as defined by PKFUNCS.H is returned if the size in bytes is greater than or equal to sizeof(DEVICE_ID).
lpBytesReturned
The number of bytes returned by the function.
Return Values
Returns TRUE if function succeeds. Returns FALSE if the function fails.
GetLastError() may be used to get the extended error value.
700 Series Color Mobile Computer User’s Manual
215
Chapter 7 — Programming
IOCTL_HAL_GET_OAL_VERINFO
Returns the HAL version information of the Pocket PC image.
Usage
#include “oemioctl.h”
Syntax
BOOL KernelIoControl( IOCTL_HAL_GET_OAL_VERINFO,LPVOID lpInBuf,DWORD
nInBufSize,LPVOID lpOutBuf,DWORD nOutBufSize,LPDWORD lpBytesReturned );
Parameters
lpInBuf
Should be set to NULL.
lpInBufSize
Should be set to zero.
lpOutBuf
Must point to a VERSIONINFO structure as defined by
OEMIOCTL.H. The fields should have these values:
S cboemverinfo
sizeof (tagOemVerInfo);
S verinfover
S sig;
“ITC\0”
S id;
‘N’
S tgtcustomer
“”
S tgtplat
SeaRay
S tgtplatversion Current build version number
S tgtcputype[8]; “Intel\0”
S tgtcpu
“PXA255\0”;
S tgtcoreversion “”
S date
Build time
S time
Build date
nOutBufSize
The size of VERSIONINFO in bytes.
lpBytesReturned
Returns sizeof(PVERSIONINFO).
Return Values
Returns TRUE if function succeeds. Returns FALSE if the function fails.
GetLastError() may be used to get the extended error value.
IOCTL_HAL_GET_BOOTLOADER_VERINFO
Returns the HAL version information of the Pocket PC image.
Usage
#include “oemioctl.h”
Syntax
BOOL KernelIoControl( IOCTL_HAL_GET_OAL_VERINFO,LPVOID lpInBuf, DWORD
nInBufSize,LPVOID lpOutBuf,DWORD nOutBufSize,LPDWORD lpBytesReturned );
Parameters
216
lpInBuf
Should be set to NULL.
nInBufSize
Should be set to zero.
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
lpOutBuf
Must point to a VERSIONINFO structure as defined by
OEMIOCTL.H. The fields should have these values:
S cboemverinfo
Sizeof (tagOemVerInfo);
S verinfover
S sig;
“ITC\0”
S id;
‘B’
S tgtcustomer
“”
S tgtplat
SeaRay
S tgtplatversion Current build version number of the
bootstrap loader
S tgtcputype[8]; “Intel\0”;
S tgtcpu
“PXA255\0”
S tgtcoreversion “”
S date
Build time
S time
Build date
nOutBufSize
The size of VERSIONINFO in bytes.
lpBytesReturned
The number of bytes returned to lpOutBuf.
Return Values
Returns TRUE if function succeeds. Returns FALSE if the function fails.
GetLastError() may be used to get the extended error value.
IOCTL_HAL_WARMBOOT
Causes the system to perform a warm-boot. The object store is retained.
Usage
#include “oemioctl.h”
Syntax
BOOL KernelIoControl( IOCTL_HAL_WARMBOOT,LPVOID lpInBuf,DWORD
nInBufSize,LPVOID lpOutBuf,DWORD nOutBufSize,LPDWORD lpBytesReturned );
Parameters
lpInBuf
Should be set to NULL.
lpInBufSize
Should be set to zero.
lpOutBuf
Should be NULL.
nOutBufSize
Should be zero.
Return Values
None.
IOCTL_HAL_COLDBOOT
Causes the system to perform a cold-boot. The object store is cleared.
Usage
#include “oemioctl.h”
Syntax
BOOL KernelIoControl( IOCTL_HAL_COLDBOOT,LPVOID lpInBuf,DWORD
nInBufSize,LPVOID lpOutBuf,DWORD nOutBufSize,LPDWORD lpBytesReturned );
700 Series Color Mobile Computer User’s Manual
217
Chapter 7 — Programming
Parameters
lpInBuf
Should be set to NULL.
lpInBufSize
Should be set to zero.
lpOutBuf
Should be NULL.
nOutBufSize
Should be zero.
Return Values
None.
IOCTL_HAL_GET_RESET_INFO
This code allows software to check the type of the most recent reset.
Usage
#include “oemioctl.h”
Syntax
BOOL KernelIoControl( IOCTL_HAL_GET_RESET_INFO,LPVOID lpInBuf,DWORD
nInBufSize,LPVOID lpOutBuf,DWORD nOutBufSize,LPDWORD lpBytesReturned );
Parameters
lpInBuf
Should be set to NULL.
lpInBufSize
Should be set to zero.
lpOutBuf
Must point to a HAL_RESET_INFO structure. See sample below.
nOutBufSize
The size of HAL_RESET_INFO in bytes.
lpBytesReturned
The number of bytes returned by the function.
Return Values
Returns TRUE if function succeeds. Returns FALSE if the function fails.
GetLastError() may be used to get the extended error value.
Sample
typedef struct {
DWORD ResetReason;
DWORD ObjectStoreState;
} HAL_RESET_INFO, * PHAL_RESET_INFO;
// most recent reset type
// state of object store
// Reset reason types
#define HAL_RESET_TYPE_UNKNOWN
#define HAL_RESET_REASON_HARDWARE
#define HAL_RESET_REASON_SOFTWARE
#define HAL_RESET_REASON_WATCHDOG
#define HAL_RESET_BATT_FAULT
#define HAL_RESET_VDD_FAULT
16
// Object store state flags
#define HAL_OBJECT_STORE_STATE_UNKNOWN
#define HAL_OBJECT_STORE_STATE_CLEAR
218
// cold
// suspend
// power fail
// warm boot
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
IOCTL_HAL_GET_BOOT_DEVICE
This IOCTL code allows software to check which device CE booted from.
Usage
#include “oemioctl.h”
Syntax
BOOL KernelIoControl( IOCTL_HAL_GET_BOOT_DEVICE,LPVOID lpInBuf,DWORD
nInBufSize,LPVOID lpOutBuf,DWORD nOutBufSize,LPDWORD lpBytesReturned );
Parameters
lpInBuf
Should be set to NULL.
lpInBufSize
Should be set to zero.
lpOutBuf
Must point to a buffer large enough to hold a DWORD (4 bytes)
with the boot device. The following boot devices are supported:
#define HAL_BOOT_DEVICE_UNKNOWN
#define HAL_BOOT_DEVICE_ROM_XIP
#define HAL_BOOT_DEVICE_ROM
#define HAL_BOOT_DEVICE_PCMCIA_ATA
#define HAL_BOOT_DEVICE_PCMCIA_LINEAR 4
#define HAL_BOOT_DEVICE_IDE_ATA
#define HAL_BOOT_DEVICE_IDE_ATAPI
nOutBufSize
The size of lpOutBuf in bytes (4).
lpBytesReturned
The number of bytes returned by the function.
Return Values
Returns TRUE if function succeeds. Returns FALSE if the function fails.
GetLastError() may be used to get the extended error value.
IOCTL_HAL_REBOOT
Note: Using this is no longer recommended, use IOCTL_HAL_WARMBOOT (page 217) or IOCTL_HAL_COLDBOOT (page 217). This is
supported for backward-compatibility but its use can lead to difficulties.
Causes the system to perform a warm-boot. The object store is retained.
Usage
#include “oemioctl.h”
Syntax
BOOL KernelIoControl( IOCTL_HAL_REBOOT,LPVOID lpInBuf,DWORD nInBufSize,LPVOID
lpOutBuf,DWORD nOutBufSize,LPDWORD lpBytesReturned );
Parameters
lpInBuf
Should be set to NULL. lpOutBuf
Should be NULL.
lpInBufSize
Should be set to zero.
Should be zero.
nOutBufSize
Return Values
None.
700 Series Color Mobile Computer User’s Manual
219
Chapter 7 — Programming
IOCTL_PROCESSOR_INFORMATION
Returns processor information.
Usage
#include “pkfuncs.h”
Syntax
BOOL KernelIoControl( IOCTL_PROCESSOR_INFORMATION,LPVOID lpInBuf,DWORD
nInBufSize,LPVOID lpOutBuf,DWORD nOutBufSize,LPDWORD lpBytesReturned );
Parameters
lpInBuf
Should be set to NULL.
nInBufSize
Should be set to zero.
lpOutBuf
Should be a pointer to the PROCESSOR_INFO structure. Its
structure stores information describing the CPU more descriptively.
typedef __PROCESSOR_INFO {
WORD
wVersion;
WCHAR szProcessorCore[40];
WORD
wCoreRevision;
WCHAR szProcessorName[40];
WORD
wProcessorRevision;
WCHAR szCatalogNumber[100];
WCHAR szVendor[100];
DWORD dwInstructionSet;
DWORD dwClockSpeed;
//
//
//
//
//
//
//
//
//
Set to value 1
“ARM\0”
“PXA255\0”
“Intel Corporation\0”
400
nOutBufSize
Should be set to sizeof(PROCESSOR_INFO) in bytes.
lpBytesReturned
Returns sizeof(PROCESSOR_INFO);
Return Values
Returns TRUE if function succeeds. Returns FALSE if the function fails.
GetLastError() may be used to get the extended error value.
IOCTL_GET_CPU_ID
Returns Xscale processor ID.
Usage
#include “oemioctl.h”
Syntax
BOOL KernelIoControl( IOCTL_GET_CPU_ID,LPVOID lpInBuf, DWORD nInBufSize,LPVOID
lpOutBuf,DWORD nOutBufSize,LPDWORD lpBytesReturned );
Parameters
220
lpInBuf
Should point to a CPUIdInfo structure defined in OEMIOCTL.H.
lpInBufSize
Should be sizeof(CPUIdInfo).
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
lpOutBuf
Should be NULL.
nOutBufSize
Should be set to 0.
lpBytesReturned
Returns sizeof(PROCESSOR_INFO);
Return Values
Returns TRUE if function succeeds. Returns FALSE if the function fails.
GetLastError() may be used to get the extended error value.
Network Selection APIs
Network Selection APIs change the network adapter configuration programmatically. See the Communications Resource Kit in the IDL for information about these APIs. The IDL is available as a download from the
Intermec web site at www.intermec.com/idl. Contact your Intermec representative for more information.
Notifications
Use the following information to programmatically control the vibrator, to
write an application to turn on the vibrator when a message is received via
the WLAN radio link, and turn it off when the user hits a key.
Vibrator support is in the NLED driver as a false LED. The vibrator is
LED 5 and identified with an CycleAdjust of –1. The vibrate option is
available in the notifications panel when the vibrator is in the system.
Regarding an applications interface to NLED.DLL, LEDs must be available for applications to use through the COREDLL.DLL file. To use the
LED functions, declare these as extern ”C” as follows:
extern ”C” BOOL WINAPI NLEDGetDeviceInfo(UINT nInfoId, void *pOutput);
extern ”C” BOOL WINAPI NLEDSetDevice( UINT nDeviceId, void *pInput);
The LEDs are enumerated for access through the data structures associated
with these APIs:
S Notification LED 0
S Radio On LED
1 (does not apply to the 730 Computer)
S Alpha Lock LED
S Scanner LED
S Low Battery
S Vibrator
5 (does not apply to the 730 Computer)
NLEDGetDeviceInfo
Usage
#include “nled.h”
Syntax
BOOL NLEDGetDeviceInfo ( UINT nInfoId, void *pOutput );
700 Series Color Mobile Computer User’s Manual
221
Chapter 7 — Programming
Parameters
nInfoId
pOutput
Integer specifying the information to return. These values are defined:
NLED_COUNT_INFO
pOutput buffer specifies the number of LEDs on the device.
NLED_SUPPORTS_INFO_ID
pOutput buffer specifies information about the capabilities
supported by the LED.
NLED_SETTINGS_INFO_ID
pOutput buffer has information about LED current settings.
Pointer to the buffer to which the information is returned. The buffer points to various structure
types defined in “nled.h”, depending on the value of nId, as detailed in the following table:
Value of nID
Structure in pOutput
LED_COUNT_INFO
NLED_COUNT_INFO
NLED_SUPPORTS_INFO
NLED_SUPPORTS_INFO
NLED_SETTINGS_INFO
NLED_SETTINGS_INFO
NLEDSetDevice
Usage
#include “nled.h”
Syntax
BOOL NLEDSetDevice ( UINT nDeviceId, void *pInput );
Parameters
nDeviceId
Integer specifying the device identification. The following is defined:
NLED_SETTINGS_INFO_ID
pInput
Contains information about the desired LED settings.
Pointer to the buffer that contains the NLED_SETTINGS_INFO structure.
Reboot Functions
There are several methods, via Kernel I/O Control functions, that an application program can use to force the 700 Color Computer to reboot.
You can also see the Device Resource Kit in the IDL for information
about these functions. The IDL is available as a download from the Intermec web site at www.intermec.com/idl. Contact your Intermec representative for information.
S IOCTL_HAL_REBOOT
This performs a warm-boot (page 219). See note below.
S IOCTL_HAL_COLDBOOT
Forces a cold reboot. This resets the 700 Color Computer, reloads Windows CE as if a power-up was performed, and discards the contents of
the Windows CE RAM-based object store (page 217).
S IOCTL_HAL_WARMBOOT
Performs a system warm-boot, preserving the object store (page 217).
Note: Using IOCTL_HAL_REBOOT is no longer recommended, use
either IOCTL_HAL_WARMBOOT or IOCTL_HAL_COLDBOOT.
IOCTL_HAL_REBOOT is still supported for backward-compatibility
but its use can lead to difficulties.
222
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
Remapping the Keypad
Note: Use caution when remapping the keypad. Improper remapping may
render the keypad unusable. Data within the 700 Color Computer could
also be lost, should any problems occur.
Applications have the ability to remap keys on the 700 Color Numeric
Keypad and 700 Color Alphanumeric Keypad. This will allow applications
to enable keys that would otherwise not be available, such as the [F1]
function key. Also, to disable keys that should not be available, such as the
alpha key because no alpha entry is required. Care should be exercised
when attempting to remap the keypad because improper remapping may
cause the keypad to become unusable. This can be corrected by cold booting the device which loads the default keymap again.
Note that remapping the keys in this way affects the key mapping for the
entire system, not just for the application that does the remapping.
There are three “planes” supported for the 700 Color Numeric Keypad
and Alphanumeric Keypad. Keys that are to be used in more than one shift
plane must be described in each plane.
Unshifted Plane
The unshifted plane contains values from the keypad when not pressed
with other keys, such as the following:
Press the Keys
Numeric Keypad
Alphanumeric Keypad
To Enter This
Gold Plane
The gold plane contains values from the keypad when a key is simultaneously pressed with the [Gold] b key on the numeric keypad or the
[Gold/White] c key on the alphanumeric keypad, such as the following:
Press the Keys
Numeric Keypad
Alphanumeric Keypad
To Enter This
[Gold] b 1
[Gold/White] c e
Send
[Gold] b 5
[Gold/White] c C
A3
[Gold] b 9
[Gold/White] c P
PgDn
700 Series Color Mobile Computer User’s Manual
223
Chapter 7 — Programming
Alpha (Blue) Plane
The alpha plane contains values from the keypad when the keypad has
been placed in alpha mode by pressing the blue alpha key, such as:
Press the Keys
Numeric Keypad
Alphanumeric Keypad To Enter This
[Alpha] F 1
[Alpha] d g
Caps
[Alpha] F 5
[Alpha] d J
[Alpha] F 9
[Alpha] d W
Key Values
Key values are stored in the registry. All units ship with a default key
mapping in its registry. Applications to change the default mapping need
to read the appropriate key from the registry into an array of Words,
modify the values required and then write the updated values back into the
registry. The registry access can be done with standard Microsoft API calls,
such as RegOpenKeyEx(), RegQueryValueEx(), and RegSetValueEx().
Numeric Keypad
The following registry keys contain the plane mappings:
S The unshifted plane mapping can be found in the registry at:
HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD\Vkey
S The gold plane mapping can be found in the registry at:
HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD\VkeyGold
S The alpha plane mapping can be found in the registry at:
HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD\VkeyAlpha
Alphanumeric Keypad
The following registry keys contain the plane mappings:
S The unshifted plane mapping can be found in the registry at:
HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD\ALPHA\Vkey
S The gold plane mapping can be found in the registry at:
HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD\ALPHA\VkeyGold
S The alpha plane mapping can be found in the registry at:
HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD\ALPHA\VkeyAlpha
How Key Values Are Stored in Registry
To know which fields to update in the registry, you must know what Scan
Codes are assigned to each physical key (see the “Keypad Scan Codes and
Meanings” table on the next page). The Scan Code is used at the lowest
level of the system to let the keypad driver know which physical key has
been pressed. The keypad driver takes that scan code and looks it up in a
table (a copy of the one stored in the registry) to determine which values
to pass on to the operating system.
224
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
Each registry key is just an array that describes to the keypad driver what
value needs to be passed for each physical key. The key values are indexed
by the scan code, this is a zero-based index. For example in the unshifted
plane, the [4] key has a scan code of 0x06. This means that the seventh
word under the “Vkey” registry key will have the value for the [4] key.
Taking a sample of the “Vkey” registry key shows the following values:
00,00,0B,05,02,03,C1,07,04,03,BE,00,34,00,00,00,. . .
The value is 34,00. The values are in reverse byte order as that is the way
the processor handles data. When writing an application, nothing needs to
be done to swap the bytes, as this will happen automatically when the data
is read into a byte value. This is something you just need to be aware of
when looking at the registry. Knowing this, we can see that the value that
the keypad driver will pass to the system is a hex 34. Looking that up on
an UNICODE character chart, we see that it maps to a “4”. If you wanted
the key, labeled “4”, to output the letter “A” instead, you would need to
change the seventh word to “41” (the hexadecimal representation of “A”
from the UNICODE chart), then put the key back into the registry.
If you wish to disable a certain key, remap its scan code to 0x00.
Note: Do not remap scan codes 0x01, 0x41, 0x42, 0x43, 0x44. Doing so
could make your 700 Color Computer unusable until you do a cold-boot.
Change Notification
Changing registry keys does not immediately change key mappings. To
notify the keypad driver the registry is updated, use the CreateEvent() API
to signal the “ITC_KEYBOARD_CHANGE” named event.
Advanced Keypad Remapping
It is also possible to map multiple key presses to one button and to map
named system events to a button. The multiple key press option could be
useful to cut down on the number of keys needed to press in a given situation or to remap which key behaves like the action key. Mapping events to
a button could be useful to change which buttons will fire the scanner,
control volume, and allow for suspending and resuming the device. Contact Intermec Technical Support for more information.
700 Series Color Mobile Computer User’s Manual
225
Chapter 7 — Programming
Scan Codes
At the lowest driver level, the 700 Color Numeric and Alphanumeric Keypads identify keys as scan codes. The keypad microcontroller sends the
codes and only the keypad firmware changes the codes.
Numeric Keypad Scan Codes and Meanings
Press
this Key
Meaning
Press
ScanCode this Key
Meaning
ScanCode
Reserved
0x00
Scanner Left
0x03
I/O button
0x01
Scanner Right
0x04
Scanner Handle Trigger
0x02
4/GHI/A2
0x06
Right arrow/Tab
0x14
None
0x07
2/ABC/End
0x15
Left arrow/Back Tab
0x08
8/TUV/* (asterisk)
0x16
None
0x09
0/Win
0x17
BkSp// (forward slash)
0x0A
5/JKL/A3
0x18
[Gold] key
0x0B
None
0x19
None
0x0C
Action/+ (plus symbol)
0x1A
Esc/– (minus sign)
0x0D
3/DEF/backlight
0x1B
Down arrow/Volume decrease
0x0E
9/WXYZ/PgDn
0x1C
1/Caps/Send
0x0F
Enter/@ (at symbol)
0x1D
7/PQRS/PgUp
0x10
6/MNO/A4
0x1E
[Alpha] key
0x11
None
0x1F-0x40
None
0x12
Charge Detect
0x41
Up arrow/Volume increase
0x13
LCD frontlight
0x42
Threshold crossed
0x42
Ambient light
0x42
Headset detected
0x43
Keypad Backlight
0x44
Threshold Crossed
0x44
Ambient Light
0x44
226
700 Series Color Mobile Computer User’s Manual
Chapter 7 — Programming
Alphanumeric Keypad Scan Codes and Meanings
Press
this Key
Meaning
Press
ScanCode this Key
Meaning
ScanCode
Reserved
0x00
N/2
0x17
I/O button
0x01
I/backlight
0x18
Scanner Handle Trigger
0x02
P/PgDn
0x19
Scanner Left
0x03
Q/, (comma)
0x1A
Scanner Right
0x04
R/+ (plus sign)
0x1B
A/A1 key
0x05
S/4
0x1C
B/A2 key
0x06
T/5
0x1D
Escape/Send
0x07
O/3
0x1E
Left arrow/Back Tab
0x08
Caps/Lock
0x1F
Up arrow/Volume increase
0x09
BkSp
0x20
Down arrow/Volume decrease
0x0A
V/. (period)
0x21
Right arrow/Tab
0x0B
W/7
0x22
Action/End
0x0C
X/8
0x23
E/Win
0x0D
U/6
0x24
F/= (equal sign)
0x0E
Gold/White
0x25
G/* (asterisk)
0x0F
NumLock
0x26
C/A3
0x10
Space
0x27
H// (forward slash)
0x11
Z/0
0x28
D/A4
0x12
Enter
0x29
J/PgUp
0x13
Y/9
0x2A
K/@ (as symbol)
0x14
None
0x2B–0x40
L/– (minus sign)
0x15
Charge Detect
0x41
M/1
0x16
LCD frontlight
0x42
Threshold Crossed
0x42
Ambient light
0x42
Headset detected
0x43
Keypad Backlight
0x44
Threshold Crossed
0x44
Ambient Light
0x44
700 Series Color Mobile Computer User’s Manual
227
Chapter 7 — Programming
Sample View of Registry Keys
Below is a sample of the current default key mapping for the 700 Color
Numeric Keypad. See your device registry for the latest key mappings.
[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD]
”ResumeMask”=dword:7
”Vkey”=hex: 00,00,0B,05,02,03,C1,07,04,03,BE,00,34,00,00,00,\
25,00,00,00,08,00,03,02,00,00,1B,00,28,00,31,00,\
37,00,01,02,00,00,26,00,27,00,32,00,38,00,30,00,\
35,00,00,00,01,03,33,00,39,00,0D,00,36,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,07,05,01,05,03,05,02,05
”VkeyGold”=hex: 00,00,0B,05,02,03,C1,07,04,03,BE,00,34,00,00,00,\
09,01,00,00,BF,00,03,02,00,00,BD,00,75,00,72,00,\
21,00,01,02,00,00,76,00,09,00,73,00,38,01,5B,00,\
35,00,00,00,BB,01,09,05,22,00,32,01,36,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,07,05,01,05,03,05,02,05
”VkeyAlpha”=hex: 00,00,0B,05,02,03,C1,07,04,03,BE,00,47,00,00,00,\
25,00,00,00,08,00,03,02,00,00,1B,00,28,00,02,02,\
50,00,01,02,00,00,26,00,27,00,41,00,54,00,20,00,\
4A,00,00,00,01,03,44,00,57,00,0D,00,4D,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,\
00,00,07,05,01,05,03,05,02,05
228
700 Series Color Mobile Computer User’s Manual
A
Configurable Settings
This appendix contains information about the Intermec Settings, Utilities,
and Wireless Network applets on the 700 Color Mobile Computer.
Note: “700 Color” pertains to 740, 741, 750, 751, 760, and 761 Computers unless otherwise noted.
The contents of the Intermec Settings applet are dependent on what hardware configuration is done for each 700 Color Computer at the time of
shipment. These settings currently only appear if a scanner or an imager
option is present.
Likewise, other applets that are specifically related to the 802.11b or
802.11b/g radio module appear when a 802.11b or 802.11b/g radio module is installed in a 700 Color Computer. Applets that are specific for
Bluetooth, CDMA/1xRTT, and GSM/GPRS radio modules only appear
when each respective hardware configuration is done on the 700 Color
Computer. See Chapter 4, “Network Support,” for more information about
the radio modules or Bluetooth.
Information about using reader commands and configuration bar codes to
configure some of your settings is also in this appendix.
Note: Information about the settings you can configure with the Intermec
Settings applet is described in the Intermec Computer Command Reference
Manual (P/N: 073529). The online manual is available from the Intermec
web site at www.intermec.com.
700 Series Color Mobile Computer User’s Manual
229
Appendix A — Configurable Settings
Configuration Parameters
A configuration parameter changes the way the 700 Color Computer operates, such as configuring a parameter to have the 700 Color Computer
emit a very loud beep in a noisy environment.
To execute configuration parameters, scan EasySet bar codes. You can use
the EasySet bar code creation software from Intermec to print configuration labels. Scan the labels to change the scanner configuration and data
transfer settings.
For more information, see the EasySet online help. EasySet is available
from the Intermec Data Capture web site.
Menus of available parameters for each group are listed. Use the scroll bars
to go through the list. Expand each menu (+) to view its parameter settings. Tap a parameter to select, or expand a parameter (+) to view its subparameters.
Note that each parameter or subparameter is shown with its default setting
or current setting in (< >) brackets. Tap a parameter or subparameter to
select that parameter, then do any of the following to change its setting:
S Typing a new value in an entry field.
S Choosing a new value from the drop-down list.
S Selecting a different option. The selected option contains a bullet.
S Tap Edit > Restore Item Defaults to restore factory-default settings.
Tap Yes when you are prompted to verify this action.
S Tap View > Refresh to discard changes and start again. Tap Yes to save
changes when you are prompted to verify this action.
230
700 Series Color Mobile Computer User’s Manual
Appendix A — Configurable Settings
Intermec Settings Applet
Information about the settings you can configure with this applet is
described in the Intermec Computer Command Reference Manual. The
online manual is available from the Intermec web site at
www.intermec.com.
See the Data Collection Resource Kit in the Intermec Developer Library
(IDL) for information about data collection functions. The IDL is available as a download from the Intermec web site at www.intermec.com/idl.
Contact your Intermec representative for more information.
To access the settings from the 700 Color Computer, tap Start > Settings
> the System tab > Intermec Settings to access its applet.
Utilities Applet
The Utilities applet examines and modifies settings and operational modes
of specific hardware and software on the 700 Color Computer: the dock
switch, registry storage, wakeup mask, and application launch keys.
To access the settings from the 700 Color Computer, tap Start > Settings
> the System tab > Utilities to access its applet.
Use the left and right arrows to scroll through the tabs along the bottom of
the applet, then tap a tab to access its menus. These tabs represent the following groups of settings or parameters:
S Dock Switch (next page)
S Registry Save (page 232)
S Wakeup Mask (page 233)
S App Launch (page 234)
700 Series Color Mobile Computer User’s Manual
231
Appendix A — Configurable Settings
Dock Switch
From the 700 Color Computer, tap Start > Settings > the System tab >
Utilities > the Dock Switch tab to access the Dock Switch applet.
Use this applet to control the position of the dock switch. This can be set
either to a COM A (phone jack for a modem) position or to a COM B
(serial) position.
If switched to COM B and suspended, the terminal has the following behavior:
S If the 700 Color Computer is on charge, the dock switch remains
switched to COM B.
S If the 700 Color Computer is off charge, the dock switch switches to
COM A and remain in this position until the 700 Color Computer resumes charge.
Registry Save
From the 700 Color Computer, tap Start > Settings > the System tab >
Utilities > the Registry Save tab to access the Registry Save applet.
For Windows Mobile 2003, the only medium available for saving the registry is the Flash File System (PSM). Registry data is stored in the
“\Flash_File_Store\Registry” path. Check Enable Registry Storage to enable this function.
232
700 Series Color Mobile Computer User’s Manual
Appendix A — Configurable Settings
To ensure that the 700 Color Computer restores the real-time clock after a
cold-boot, check the Enable RTC Restore option. Note that this does not
apply to the 730 Computer.
700 Color Screen
730 Screen
Wakeup Mask
From the 700 Color Computer, tap Start > Settings > the System tab >
Utilities > the Wakeup Mask tab to access the Wakeup Mask applet.
This applet programs three scanner buttons and the A1 and A2 application
keys to be “wakeup” or resume keys. That is, to prompt the 700 Color
Computer to “wake up” or resume activity after going to “sleep” as a result
of being inactive after a length of time. This information will remain between warm and cold boots.
Check the appropriate box, then tap ok to apply your settings.
700 Series Color Mobile Computer User’s Manual
233
Appendix A — Configurable Settings
Based on your setting, do the following to “wake up” the 700 Computer:
If you select:
Then do this on
Numeric Keyboard
Then do this on
Alphanumeric Keyboard
Middle Scanner Button
Squeeze the button on the Scan Handle
Squeeze the button on the Scan Handle
Left Scanner Button
Squeeze the left scanner button
Squeeze the left scanner button
Right Scanner Button
Squeeze the right scanner button
Squeeze the right scanner button
GOLD + A1 (Application 1)
Press [Gold] b a
Press [Gold/White] c A
GOLD + A2 (Application 2)
Press [Gold] b 4
Press [Gold/White] c B
App Launch
From the 700 Color Computer, tap Start > Settings > the System tab >
Utilities , then scroll to the right to tap the App Launch tab to access the
Application Launch applet.
This applet programs or maps two scanner buttons and four application
keys to start up to six applications. Note the left scanner button also acts as
the record button.
For 700 Color Computers with either a laser scanner or an imager,
default mappings are shown in the following illustration.
For 700 Color Computers without either a laser scanner or an imager,
the default maps the Record, Calendar, Contacts, and Tasks applications
the top four and the A3 and A4 buttons are “unassigned” or available for
two more applications.
Note: Record, Calendar, Contacts, and Tasks are Pocket PC applications.
See Chapter 2, “Windows Mobile 2003,” for more information.
S To assign an application to a button, select an application from the applicable drop-down list box.
S To assign a new application, select the “Add new application” option,
which brings up an Open File dialog and browse Secure Digital or
CompactFlash storage cards for new applications.
234
700 Series Color Mobile Computer User’s Manual
Appendix A — Configurable Settings
S To disable or unmap a currently mapped application from a corresponding button, select “unassigned” from the applicable drop-down list.
S To restore these buttons to their defaults, tap Defaults in the lower
right corner.
Note; You cannot map an application to more than one button. Should
you assign the same application to two buttons, a verification prompt will
appear after the second button to confirm whether you want to remap the
application. If you tap Yes, the applet changes the first button to “unassigned” and map the application to the second button.
Note: All changes are activated immediately upon selection.
Wireless Network Applet
Note: See Chapter 4, “Network Support,” for information about the
802.11b or 802.11b/g radio module.
About the Wireless Network
Your wireless adapter (network interface card) connects to wireless networks of two types: infrastructure networks and ad-hoc networks.
S Infrastructure networks get you onto your corporate network and the
internet. Your 700 Color Computer establishes a wireless connection to
an access point, which links you to the rest of the network. When you
connect to a network via an access point, you are using the 802.11b or
802.11b/g infrastructure mode.
S Ad-hoc networks are private networks shared between two or more clients, even with no access point.
Each wireless network is assigned a name (or Service Set Identifier —
SSID) to allow multiple networks to coexist in the same area without infringement.
Intermec recommends using security measures with wireless networks to
prevent unauthorized access to your network and to ensure your privacy of
transmitted data. The following are required elements for secure networks:
S Authentication by both the network and the user
S Authentication is cryptographically protected
S Transmitted data
There are many schemes available for implementing these features.
Terminology
Below and on the next page are terms you may encounter as you configure
your wireless network:
S CKIP (Cisco Key Integrity Protocol)
This is Cisco’s version of the TKIP protocol, compatible with Cisco
Airnet products.
700 Series Color Mobile Computer User’s Manual
235
Appendix A — Configurable Settings
S EAP (Extensible Authentication Protocol)
802.11b or 802.11b/g uses this protocol to perform authentication.
This is not necessarily an authentication mechanism, but is a common
framework for transporting actual authentication protocols. Intermec
provides a number of EAP protocols to choose for your network.
S TKIP (Temporal Key Integrity Protocol)
This protocol is part of the IEEE 802.11i encryption standard for wireless LANs., which provides per-packet key mixing, a message integrity
check and a re-keying mechanism, thus overcoming most of the weak
points of WEP. This encryption is more difficult to crack than the standard WEP. Weak points of WEP include:
S No Installation Vector (IV) reuse protection
S Weak keys
S No protection against message replay
S No detection of message tampering
S No key updates
S WEP (Wired Equivalent Privacy) encryption
With preconfigured WEP, both the client 700 Color Computer and
access point are assigned the same key, which can encrypt all data between the two devices. WEP keys also authenticate the 700 Color Computer to the access point — unless the 700 Color Computer can prove
it knows the WEP key, it is not allowed onto the network.
WEP keys are only needed if they are expected by your clients. There
are two types available: 64-bit (5-character strings, 12345) (default) and
128-bit (13-character strings, 1234567890123). Enter these as either
ASCII (12345) or Hex (0x3132333435).
S WPA (Wi-Fi Protected Access)
This is an enhanced version of WEP that does not rely on a static,
shared key. It encompasses a number of security enhancements over
WEP, including improved data encryption via TKIP and 802.11b or
802.11b/g authentication with EAP.
WiFi Alliance security standard is designed to work with existing
802.11 products and to offer forward compatibility with 802.11i.
Configuring Your Wireless Network
To start 802.11b or 802.11b/g communications on the 700 Color
Computer, tap Start > Settings > the System tab > Wireless Network to
access the Profile Wizard for the 802.11b or 802.11b/g radio module.
A profile contains all the information necessary to authenticate you to the
network, such as login name, password or certificate, and protocols by
which you are authenticated.
You can have up to four profiles for different networks. For example, you
may have different login names or passwords on different networks, or you
may use a password on one network, and a certificate on another.
236
700 Series Color Mobile Computer User’s Manual
Appendix A — Configurable Settings
Use the Profiles page to select and configure between the networking environments assigned to this 802.11b or 802.11b/g radio.
S Profile:
Tap the drop-down list to choose between four different profiles assigned to this unit, then tap Edit Select Profile, make the changes needed for this profile (starting on the next page), then tap OK to return to
the Profiles page.
S Enable Microsoft’s Wireless Zero Config
Check this box to enable Microsoft’s Wireless Zero Config application.
This effectively disables the Intermec software solution for 802.11b or
802.11b/g, including configuration via the Wireless Network applet.
Basic
Use the Basic page to set the network type, name, and manage battery
power for this profile. Tap ok to return to the Profiles page.
S Profile Label:
Enter a unique name for your profile.
S Network type:
Tap the drop-down list to select either “Infrastructure” if your network
uses access points to provide connectivity to the corporate network or
internet; or “Ad-Hoc” to set up a private network with one or more participants.
S Channel:
If you selected “Ad-Hoc” for the network type, select the channel on
which you are communicating with others in your network. There are
up to 11 channels available.
S SSID (Network Name):
This assumes the profile name unless another name is entered in this field.
If you want to connect to the next available network or are not familiar
with the network name, enter “ANY” in this field. Consult your LAN
administrator for network names.
700 Series Color Mobile Computer User’s Manual
237
Appendix A — Configurable Settings
S Enable Power Management:
Check this box to conserve battery power (default), or clear this box to
disable this feature.
Security
The following are available from the 8021x Security drop-down list. Note
the last four methods are available if you have purchased the security package.
Contact your Intermec representative for information.
S None (below)
S TTLS (page 244)
S PEAP (page 240)
S LEAP (page 247)
S TLS (page 242)
S EAP-FAST (page 249)
None
Use “None” to disable 802.11b or 802.11b/g Security and enable either
WEP or WPA-PSK encryption.
To Disable 802.1x Security
Set 8021x Security and Encryption as “None” and Association to “Open.”
238
700 Series Color Mobile Computer User’s Manual
Appendix A — Configurable Settings
To Enable WEP Encryption
1 Set 8021x Security as “None.”
2 Set Association to either “Open” if WEP keys are not required; or
“Shared” when WEP keys are required for association.
3 Set Encryption to “WEP” (see page 236).
4 If you had set Association to “Shared,” then select a data transmission
key from the Data TX Key drop-down list near the bottom of this
screen, then enter the encryption key for that data transmission in the
appropriate Key # field.
To Enable WPA Encryption Using a Preshared Key
1 Set 8021x Security as “None.”
2 Set Association to “WPA” (see page 236).
3 Enter the temporal key as ASCII (12345) in the Pre-Shared Key field.
700 Series Color Mobile Computer User’s Manual
239
Appendix A — Configurable Settings
PEAP (Protected EAP)
This protocol is suitable for performing secure authentication against Windows domains and directory services. It is comparable to EAP-TTLS (see
page 244), both in its method of operation and its security, though not as
flexible. This does not support the range of inside-the-tunnel authentication methods supported by EAP-TTLS. Microsoft and Cisco both support
this protocol.
Use “PEAP” to configure the use of PEAP as an authentication protocol
and to select “Open,” “WPA,” or “Network EAP” as an association mode.
To Enable PEAP with an Open Association
1 Set 8021x Security as “PEAP.”
2 Set Association to “Open.”
3 Enter your unique user name and password to use this protocol. Select
Prompt for password to have the user enter this password each time to
access the protocol; or leave Use following password as selected to automatically use the protocol without entering a password.
4 Tap Get Certificates to obtain or import server certificates (page 247).
5 Tap Additional Settings to assign an inner PEAP authentication and set
options for server certificate validation and trust (see page 242).
To Enable PEAP with WPA Encryption
1 Set 8021x Security as “PEAP.”
2 Set Association to “WPA” (see page 236).
3 Enter your unique user name and password to use this protocol. Select
Prompt for password to have the user enter this password each time to
access the protocol, or leave Use following password as selected to automatically use the protocol without entering a password.
4 Tap Get Certificates to obtain or import server certificates (page 247).
240
700 Series Color Mobile Computer User’s Manual
Appendix A — Configurable Settings
5 Tap Additional Settings to assign an inner PEAP authentication and set
options for server certificate validation and trust (see page 242).
To Enable PEAP with Network EAP
1 Set 8021x Security as “PEAP.”
2 Set Association to “Network EAP” (see page 236).
3 Set Encryption to either “WEP” (page 236) or “CKIP” (page 235).
4 Enter your unique user name and password to use this protocol. Select
Prompt for password to have the user enter this password each time to
access the protocol, or leave Use following password as selected to automatically use the protocol without entering a password.
5 Tap Get Certificates to obtain or import server certificates (page 247).
6 Tap Additional Settings to assign an inner PEAP authentication and set
options for server certificate validation (see page 242).
700 Series Color Mobile Computer User’s Manual
241
Appendix A — Configurable Settings
Additional Settings
1 Select an authentication method from the Inner PEAP Authentication
drop-down list.
EAP/MS-CHAP-V2
Authenticates against a Windows Domain Controller and
other non-Windows user databases. This is Microsoft’s
implementation of PEAP.
EAP/Token Card
Use with token cards. The password value entered is never
cached. This is Cisco’s implementation of PEAP.
EAP/MD5-Challenge Message Digest 5. A secure hashing authentication algorithm.
2 Check Validate Server Certificate to verify the identity of the authentication server based on its certificate when using TTLS or PEAP.
3 Enter the Common Names of trusted servers. Note if these fields are left
blank, the server certificate trust validation is not performed or required.
4 Click ok to return to the Security page.
TLS (EAP-TLS)
EAP-TLS is a protocol that is based on the TLS (Transport Layer Security)
protocol widely used to secure web sites. This requires both the user and
authentication server have certificates for mutual authentication. While
cryptically strong, this requires corporations that deploy this to maintain a
certificate infrastructure for all their users.
Use “TLS” to configure the use of EAP-TLS as an authentication protocol,
and select either “Open” or “WPA” as an association mode.
To Enable TLS with an Open Association
1 Set 8021x Security as “TLS.”
2 Set Association to “Open.”
3 Enter your unique Subject Name and User Name to use this protocol.
242
700 Series Color Mobile Computer User’s Manual
Appendix A — Configurable Settings
4 Tap Get Certificates to obtain or import server certificates (page 247).
5 Tap Additional Settings to set server certificate validation (page 244).
To Enable TLS with WPA Encryption
1 Set 8021x Security as “TLS.”
2 Set Association to “WPA” (see page 236).
3 Enter unique Subject Name and User Name credentials for this profile.
4 Tap Get Certificates to obtain or import server certificates (page 247).
5 Tap Additional Settings to set server certificate validation (page 244).
700 Series Color Mobile Computer User’s Manual
243
Appendix A — Configurable Settings
Additional Settings
1 Check Validate Server Certificate to verify the identity of the authentication server based on its certificate when using PEAP or TLS.
2 Enter the Common Names of trusted servers. Note that if these fields are
left blank, the server certificate trust validation is not performed or required.
3 Click ok to return to the Security page.
TTLS (EAP-Tunneled TLS)
This protocol provides authentication like EAP-TLS (see page 242) but
does not require certificates for every user. Instead, authentication servers
are issued certificates. User authentication is done using a password or other credentials that are transported in a securely encrypted “tunnel” established using server certificates.
EAP-TTLS works by creating a secure, encrypted tunnel through which
you present your credentials to the authentication server. Thus, inside
EAP-TTLS there is another inner authentication protocol that you must
configure via Additional Settings.
Use “TTLS” to configure the use of EAP-TTLS as an authentication protocol, and select either “Open” or “WPA” as an association mode.
To Enable TTLS with an Open Association (default configuration)
1 Set 8021x Security as “TTLS.”
2 Set Association to “Open.”
3 Enter your unique user name and password to use this protocol. Select
Prompt for password to have the user enter this password each time to
access the protocol, or leave Use following password as selected to automatically use the protocol without entering a password.
4 Tap Get Certificates to obtain or import server certificates (page 247).
5 Tap Additional Settings to assign an inner TTLS authentication and an
inner EAP, and set server certificate validation and trust (page 246).
244
700 Series Color Mobile Computer User’s Manual
Appendix A — Configurable Settings
To Enable TTLS with WPA Encryption
1 Set 8021x Security as “TTLS.”
2 Set Association to “WPA” (see page 236).
3 Enter your unique user name and password to use this protocol. Select
Prompt for password to have the user enter this password each time to
access the protocol, or leave Use following password as selected to automatically use the protocol without entering a password.
4 Tap Get Certificates to obtain or import server certificates (page 247).
5 Tap Additional Settings to assign an inner TTLS authentication and an
inner EAP, and set server certificate validation and trust (see page 246).
700 Series Color Mobile Computer User’s Manual
245
Appendix A — Configurable Settings
Additional Settings
1 Select an authentication protocol from the Inner TTLS Authentication
drop-down list:
PAP
Password Authentication Protocol. A simple authentication
protocol that sends security information in the clear.
CHAP
Challenge Handshake Authentication Protocol. Use of Radius
to authenticate a terminal without sending security data in the
clear. Authenticates against non-Windows user databases. You
cannot use this if authenticating against a Windows NT Domain
or Active Directory.
MS-CHAP;
MS-CHAP-V2
Authenticates against a Windows Domain Controller and other
non-Windows user databases.
PAP/Token Card
Use with token cards. The password value entered is never
cached.
EAP
Extensible Authentication Protocol. See page 236 for information about EAP.
2 If you select “EAP” for the inner authentication protocol, then select an
inner EAP protocol from the Inner EAP drop-down list.
3 Enter the Common Names of trusted servers. Note that if these fields are
left blank, the server certificate trust validation is not performed or required.
4 Check Validate Server Certificate to verify the identity of the authentication server based on its certificate when using TTLS, PEAP, and TLS.
5 Enter the Anonymous EAP-TTLS Name as assigned for public usage.
Use of this outer identity protects your login name or identity.
6 Click ok to return to the Security page.
246
700 Series Color Mobile Computer User’s Manual
Appendix A — Configurable Settings
To Get Certificates
Certificates are pieces of cryptographic data that guarantee a public key is
associated with a private key. They contain a public key and the entity
name that owns the key. Each certificate is issued by a certificate authority.
Use this page to import a certificate onto the 700 Color Computer.
Root Certificates
1 Tap the <<< button next to the Import Root Certificate field to select
the root certificate (DER-encoded .CER file) to import.
2 Click Import Root Cert to install the selected certificate.
User Certificate
1 Tap the <<< button next to the Certificate Path field to select the user
certificate (DER-encoded .CER file without the private key) to import.
2 Tap the <<< button next to the Key Path field to select the private key
(.PVK file) which corresponds to the user certificate chosen in step 1.
3 Tap Import User Cert to install the selected certificate.
Web Enrollment
Tap Web Enrollment to obtain a user certificate over the network from an
IAS Server. Tap ok to return to the Security page.
LEAP (Cisco Lightweight EAP)
LEAP is the Cisco Lightweight version of EAP. See page 236 for information about EAP.
Use “LEAP” to configure the use of LEAP as an authentication protocol,
select “Open,” “WPA,” or “Network EAP” as an association mode. Note
this defaults to the Network EAP.
To Enable LEAP with an Open Association
1 Set 8021x Security as “LEAP” and Association to “Open.”
2 Enter your unique User Name to use this protocol.
700 Series Color Mobile Computer User’s Manual
247
Appendix A — Configurable Settings
3 Select Prompt for password to have the user enter this password each
time to access the protocol, or leave Use following password as selected
to automatically use the protocol without entering a password.
To Enable LEAP with WPA Encryption
1 Set 8021x Security as “LEAP” and Association to “WPA” (see page
236).
2 Enter your unique User Name to use this protocol.
3 Select Prompt for password to have the user enter this password each
time to access the protocol, or leave Use following password as selected
to automatically use the protocol without entering a password.
To Enable LEAP with Network EAP
1 Set 8021x Security as “LEAP,” Association to “Network EAP” (see page
236), and Encryption to either “WEP” (page 236) or “CKIP” (page
235).
2 Enter your unique User Name to use this protocol.
248
700 Series Color Mobile Computer User’s Manual
Appendix A — Configurable Settings
3 Select Prompt for password to have the user enter this password each
time to access the protocol, or leave Use following password as selected
to automatically use the protocol without entering a password.
EAP-FAST (EAP -Flexible Authentication via Secured Tunnel)
The EAP-FAST protocol is a client-server security architecture that encrypts EAP transactions with a TLS tunnel. While similar to PEAP, it differs significantly as EAP-FAST tunnel establishment is based on strong secrets unique to users. These secrets are called Protected Access Credentials
(PACs), which CiscoSecure ACS generates using a master key known only
to CiscoSecure ACS. Because handshakes based upon shared secrets are
intrinsically faster than handshakes based upon PKI, EAP-FAST is the significantly faster of the two solutions that provide encrypted EAP transactions. No certificate management is required to implement EAP-FAST.
Use “EAP-FAST” to configure the use of EAP-FAST as an authentication
protocol, select “Open,” “WPA,” or “Network EAP” as an association
mode. Note this defaults to the Network EAP.
To Enable EAP-FAST with an Open Association
1 Set 8021x Security as “EAP-FAST” and Association to “Open.”
2 Enter your unique Username to use this protocol.
3 Select Prompt for password to have the user enter this password each
time to access the protocol, or leave Use following password as selected
to automatically use the protocol without entering a password.
700 Series Color Mobile Computer User’s Manual
249
Appendix A — Configurable Settings
4 Tap Additional Settings to set options for PAC management and assign
an anonymous EAP-FAST name (see page 251).
To Enable EAP-FAST with WPA Encryption
1 Set 8021x Security as “EAP-FAST” and Association to “WPA” (see
page 236).
2 Enter your unique Username to use this protocol.
3 Select Prompt for password to have the user enter this password each
time to access the protocol, or leave Use following password as selected
to automatically use the protocol without entering a password.
4 Tap Additional Settings to set options for PAC management and assign
an anonymous EAP-FAST name (see page 251).
To Enable EAP-FAST with Network EAP
1 Set 8021x Security as “EAP-FAST,” Association to “Network EAP”
(page 236), and Encryption to either “WEP”(page 236) or “CKIP”
(page 235).
250
700 Series Color Mobile Computer User’s Manual
Appendix A — Configurable Settings
2 Enter your unique Username to use this protocol.
3 Select Prompt for password to have the user enter this password each
time to access the protocol, or leave Use following password as selected
to automatically use the protocol without entering a password.
4 Tap Additional Settings to set options for PAC management and assign
an anonymous EAP-FAST name. See below for more information.
Additional Settings
1 Tap PAC Manager to view the PAC files currently installed on your
700 Color Computer. Tap ok to return to the Additional Settings
screen.
2 If you already have a PAC on your 700 Color Computer, clear Allow
Automatic PAC provisioning to avoid receiving additional PACs from
the server.
3 If Allow Automatic PAC provisioning is checked, you can check:
S Prompt before acquiring a new PAC for notification of any incoming PACs.
S Prompt before replacing a PAC for notification whether to replace a
current PAC with an incoming PAC.
4 Enter the Anonymous EAP-FAST Name as assigned for public usage.
This outer identity protects your login name or identity.
700 Series Color Mobile Computer User’s Manual
251
Appendix A — Configurable Settings
5 Check ok to return to the Security page.
Advanced
Use this page to configure additional settings for this profile. Tap ok or
OK to return to the Profiles page.
S Detect Rogue APs:
Wireless NICs and APs associate based on the SSID configured for the
NIC. Given an SSID, the BSSID with the strongest signal is often chosen for association. After association, 802.1x authentication may occur
and during authentication credentials to uniquely identify a user —
these are passed between the NIC and the AP.
The base 802.1x technology does not protect the network from “rogue
APs.” These can mimic a legitimate AP to authentication protocols and
user credentials. This provides illegal users ways to mimic legitimate users and steal network resources and compromise security.
Check this box to detect and report client behavior suspected of being
rogue APs. Once a rouge AP is detected, your 700 Series Computer no
longer associates with that AP until you perform a warm boot.
Clear this box to solve AP connection problems that result when an AP
gets put on the rogue AP list due to inadvertent failed authentications
and not because it is a real rouge.
S Enable mixed cell:
Mixed cell is a profile-dependent setting. If enabled, you can connect to
mixed cell without using WEP, then you can query the cell to determine whether you can use encryption.
252
700 Series Color Mobile Computer User’s Manual
Appendix A — Configurable Settings
S Enable Logging:
Check this box to log what activity incurs for this profile.
Other Configurable Parameters
These can be configured by sending reader commands (next page) through
the network or from an application.
Audio Volume
Changes the volume of all audio signals.
Off
Very quiet
Quiet
Normal (default)
Loud
Very loud
Automatic Shutoff
Sets the length of time the 700 Color Computer remains on when there is no activity. When you turn on
the 700 Color Computer, it either resumes exactly
where it was when you turned it off or boots and restarts
your application.
1 minute
2 minutes
3 minutes (default)
4 minutes
5 minutes
Backlight Timeout
Sets the length of time that the display backlight remains on. If you set a longer timeout value, you use the
battery power at a faster rate.
10
30
60
120
180
240
300
Date/Time
Sets the current date and time.
Date Year
Month
Day
Time Hour
Minute
Second
Key Clicks
Enables or disables the keypad clicks. The 700 Color
Computer emits a click each time you press a key or
decode a row of a two-dimensional symbology.
0 Disable clicks
1 Enable soft key clicks
2 Enable loud key clicks (default)
700 Series Color Mobile Computer User’s Manual
10 seconds
30 seconds
1 minute (default)
2 minutes
3 minutes
4 minutes
5 minutes
0000–9999 (1999)
1–12 (6)
1–31 (1)
0–23 (0)
0–59 (00)
0–59 (00)
253
Appendix A — Configurable Settings
Using Reader Commands
After the 700 Color Computer is connected to your network, you can
send the 700 Color Computer a reader command from an application to
perform a task, such as changing the time and date. Some reader commands temporarily override the configuration settings and some change
the configuration settings.
Change Configuration
The Change Configuration command must precede any configuration
command. If you enter a valid string, the 700 Color Computer configuration is modified and the computer emits a high beep. To send the Change
Configuration command through the network, use the $+ [command]
syntax where command is the two-letter command syntax for the configuration command followed by the value to be set for that command.
You can also make changes to several different commands by using the
$+ [command]...[command n] syntax. There are seven configuration
command settings that can be changed in this way. See each command for
information on respective acceptable “data” values.
Command
Syntax
Audio Volume
BVdata
Automatic Shutoff
EZdata
Backlight Timeout
DFdata
Key Clicks
KCdata
Virtual Wedge Grid
AFdata
Virtual Wedge Postamble
AEdata
Virtual Wedge Preamble
ADdata
Example 1
To change the Beep Volume to Off, you can send this string to the 700
Color Computer through the network: $+BV0
where:
$+
Indicates Change Configuration.
BV
Specifies the Audio Volume parameter.
Specifies a value of Off.
Example 2
To change the Beep Volume to Very Quiet and the Virtual Wedge Grid
to 123: $+BV1AF123
where:
$+
Indicates Change Configuration
BV1
Specifies Audio Volume, set to Very Quiet (1)
AF123
Specifies Virtual Wedge Grid, set to a value of 123.
254
700 Series Color Mobile Computer User’s Manual
Appendix A — Configurable Settings
Set Time and Date
This command sets the date and time on the 700 Color Computer. The
default date and time is June 1, 1999 at 12:00 AM.
From the network, send the following:
/+ yyyymmddhhmmss
where acceptable values for the date are:
yyyy
0000–9999 Year
mm
01–12
Month of the year
dd
01–31
Day of the month
hh
00–23
Hour
mm
00–59
Minutes
ss
00–59
Seconds
You can also set the time and date by using Configuration Management in
Unit Manager, or by using the Clock applet in the Settings menu. To
access this applet, tap Start > Settings > the System tab > the Clock icon.
Configuration Bar Codes
You can change some settings on your 700 Color Computer by scanning
the following Code 39 bar code labels.
Note: When you use a bar code creation utility to make a scannable bar
code label, the utility probably adds opening and closing asterisks automatically. Asterisks are included here for translation purposes.
Audio Volume
Note: The Audio Volume parameter information is on page 253.
Turn Audio Off
*$+BV0*
*$+BV0*
700 Series Color Mobile Computer User’s Manual
255
Appendix A — Configurable Settings
Set Audio Volume to very quiet
*$+BV1*
*$+VB1*
Set Audio Volume to quiet
*$+BV2*
*$+BV2*
Set Audio Volume to normal (default)
*$+BV3*
*$+BV3*
Set Audio Volume to loud
*$+BV4*
*$+BV4*
Set Audio Volume to very loud
*$+BV5*
*$+BV5*
Automatic Shutoff
Note: The Automatic Shutoff parameter information is on page 253.
Set Automatic Shutoff to 1 minute
*$+EZ1*
*$+EZ1*
Set Automatic Shutoff to 2 minutes
*$+EZ2*
*$+EZ2*
Set Automatic Shutoff to 3 minutes (default)
*$+EZ3*
*$+EZ3*
Set Automatic Shutoff to 4 minutes
*$+EZ4*
*$+EZ4*
Set Automatic Shutoff to 5 minutes
*$+EZ5*
*$+EZ5*
Backlight Timeout
Note: The Backlight Timeout parameter information is on page 253.
Backlight Timeout 10 seconds
*$+DF10*
*$+DF10*
256
700 Series Color Mobile Computer User’s Manual
Appendix A — Configurable Settings
Backlight Timeout 30 seconds
*$+DF30*
*$+DF30*
Backlight Timeout 1 minute (default)
*$+DF60*
*$+DF60*
Backlight Timeout 2 minutes
*$+DF120*
*$+DF120*
Backlight Timeout 3 minutes
*$+DF180*
*$+DF180*
Backlight Timeout 4 minutes
*$+DF240*
*$+DF240*
Backlight Timeout 5 minutes
*$+DF300*
*$+DF300*
Key Clicks
Note: The Key Clicks parameter information is on page 253.
Disable key clicks
*$+KC0*
*$+KC0*
Enable soft key clicks
*$+KC1*
*$+KC1*
Enable loud key clicks (default)
*$+KC2*
*$+KC2*
Virtual Wedge Grid, Preamble, Postamble
The following parameters are user-configurable strings. Refer to a full
ASCII chart for more information.
Grid
For Virtual Wedge Grid, the first part of the bar code is the following,
which can include a string of up to 240 characters.
*$+AF
*$+AF
700 Series Color Mobile Computer User’s Manual
257
Appendix A — Configurable Settings
Preamble
For Virtual Wedge Preamble, the first part of the bar code is below, followed by a string of up to 31 characters (no ) and an asterisk. Default is no characters.
*$+AD
*$+AD
Postamble
For Virtual Wedge Postamble, the first part of the bar code is below, followed by a string of up to 31 characters (no ) and an asterisk. Default is no characters.
*$+AE
*$+AE
258
700 Series Color Mobile Computer User’s Manual
B
Troubleshooting
This appendix contains a brief explanation of what you can do to troubleshoot your 700 Color Mobile Computer.
700 Series Color Mobile Computer User’s Manual
259
Appendix B — Troubleshooting
Problem
Solutions
The 700 Color Computer does not respond when connected to a power supply.
Make sure your ac adapter or dock is plugged in and is
making good contact with your mobile computer.
The 700 Color Computer will not turn on when the I/O
key is pressed.
The AB10 battery may be low and need recharging.
The Power status LED starts blinking.
The Power status LED provides the status of your battery pack when it is connected to a charging device. See
Chapter 1, “Introduction,” for LED descriptions.
The 700 Color Computer will not turn on and the
screen is blank.
The battery may be critically low. Put your mobile computer in an AD15 or AD18 charger for at least five minutes, remove it from the dock, then press the I/O button.
The screen should turn on.
Put your mobile computer back in the charger and continue to charge your mobile computer for at least four
hours to make sure the battery is fully charged.
The 700 Color Computer will not turn on when placed
in a dock.
Make sure the dock is plugged in and your mobile computer is securely seated in the dock.
The 700 Color Computer shuts down during operation.
You may have a very low battery. Put the battery in an
AC15 or AC16 charger.
The 700 Color Computer does not turn off.
The 700 Color Computer does not turn off while it is
processing data. If this situation continues for a long
period of time, it does run down the battery unless you
have it connected to an external power, or in a charging
dock.
Should the 700 Color Computer lock up, perform a
warm-boot. If the mobile computer stays locked up, then
perform a cold-boot. See Chapter 1, “Introduction,” for
information on performing warm-boots and cold-boots.
The 700 Color Computer takes a long time to boot up
after a warm- or cold-boot is performed.
260
Normal recovery time is 30 to 45 seconds. If the recovery
takes longer, then contact support personnel.
700 Series Color Mobile Computer User’s Manual
I
Index
The Classes and Functions Index covers 700 Color classes and functions.
The General Index covers all topics. Those in italics are figures, those in bold are
tables.
The Files Index is to assist you in locating descriptions for device drivers, applications, utilities, batch files, or other files within this publication.
700 Series Color Mobile Computer User’s Manual
261
Index
Classes and Functions
add_registry_section, [AddReg]
flags, 194
registry_root_string, 194
value_name, 194
AddReg, [DefaultInstall], 191
[AddReg], add_registry_section
flags, 194
registry_root_string, 194
value_name, 194
AppName, [CEStrings], 189
Asset management, DeviceURL parameter, 204
BlockSize, FTP Server, 204
BuildMax, [CEDevice], 190
BuildMin, [CEDevice], 190
[CEDevice]
BuildMax, 190
BuildMin, 190
ProcessorType, 189
UnsupportedPlatforms, 189
VersionMax, 190
VersionMin, 190
CESelfRegister, [DefaultInstall], 191
CESetupDLL, [DefaultInstall], 191
CEShortcuts, [DefaultInstall], 191
[CEShortcuts], shortcut_list_section
shortcut_filename, 194
shortcut_type_flag, 194
target_file/path, 195
target_file_path, 195
CESignature
[SourceDiskNames], 191
[Version], 188
[CEStrings]
AppName, 189
InstallDir, 189
ClassID field values
VN_CLASS_ASIC, 212
VN_CLASS_BOOTSTRAP, 212
VN_CLASS_KBD, 212
CloseHandle()
DTR printing, 167, 168
IrDA printing, 162
NPCP printing, 163, 164
Cold boot, IOCTL_HAL_COLDBOOT, 217
Copyfiles, [DefaultInstall], 191
[CopyFiles], file_list_section
destination_filename, 193
flags, 193
source_filename, 193
CreateEvent(), 225
CreateFile()
DTR printing, 167
262
IrDA printing, 162
NPCP printing, 163, 164
[DefaultInstall]
AddReg, 191
CESelfRegister, 191
CESetupDLL, 191
CEShortcuts, 191
Copyfiles, 191
DeregisterDevice(), 163
DTR printing, 167
[DestinationDirs], file_list_section, 192
DeviceIOControl()
DTR printing, 167
NPCP printing, 163
DeviceIoControl(), NPCP printing, 164
DeviceName, FTP Server, 204
DeviceURL, FTP Server, 204
disk_ordinal, [SourceDiskNames], 191
DllRegisterServer, 191
DllUnregisterServer, 191
ERROR_INSUFFICIENT_BUFFER
IOCTL_HAL_ITC_READ_PARM, 211
IOCTL_HAL_ITC_WRITE_SYSPARM, 214
ERROR_INVALID_PARAMETER
IOCTL_HAL_ITC_READ_PARM, 211
IOCTL_HAL_ITC_WRITE_SYSPARM, 214
File Transfer Protocol. See FTP
file_list_section
[CopyFiles]
destination_filename, 193
flags, 193
source_filename, 193
[DestinationDirs], 192
filename, [SourceDiskFiles], 192
FTP
client, 205
configurable parameters, 204
BlockSize, 204
DeviceName, 204
DeviceURL, 204
PauseAtStartup, 205
FTPDCMDS subdirectory, 208
RTC 959, 208
server, 205
server requests
CDUP, 205
CWD, 205
DELE, 206
HELP, 206
LIST, 206
MKD, 206
MODE, 206
NLST, 206
NOOP, 206
PASS, 206
PWD, 206
700 Series Color Mobile Computer User’s Manual
Index
QUIT, 206
RETR, 206
RMD, 206
RNFR, 206
RNTO, 206
SITE, 206
SITE ATTRIB, 206
SITE BOOT, 207
SITE COPY, 207
SITE EKEY, 207
SITE EVAL, 207
SITE EXIT, 207
SITE GVAL, 208
SITE HELP, 207
SITE KILL, 207
SITE LOG, 207
SITE PLIST, 207
SITE PVAL, 208
SITE RUN, 207
SITE STATUS, 207
SITE TIMEOUT, 207
STOR, 206
SYST, 206
TYPE, 206
USER, 206
XCUP, 206
XCWD, 206
XMKD, 206
XPWD, 206
XRMD, 206
stopping server from application, 208
support, 205
web browsers, 208
HAL, verion of Pocket PC
IOCTL_HAL_GET_BOOTLOADER_VERINFO,
216
IOCTL_HAL_GET_OAL_VERINFO, 216
ID field values
IOCTL_HAL_ITC_READ_PARM
ITC_NVPARM_80211_INSTALLED, 213
ITC_NVPARM_80211_RADIOTYPE, 213
ITC_NVPARM_ANTENNA_DIVERSITY, 212
ITC_NVPARM_BLUETOOTH_INSTALLED,
213
ITC_NVPARM_CONTRAST, 212
ITC_NVPARM_DISPLAY_TYPE, 212
ITC_NVPARM_ECN, 212
ITC_NVPARM_EDBG_SUBNET, 212
ITC_NVPARM_EDG_IP, 212
ITC_NVPARM_ETHERNET_ID, 212
ITC_NVPARM_INTERMEC_DATACOLLECTION_HW, 213
ITC_NVPARM_INTERMEC_DATACOLLECTION_SW, 212
700 Series Color Mobile Computer User’s Manual
ITC_NVPARM_INTERMEC_SOFTWARE_CONTENT, 212
ITC_NVPARM_LAN9000_INSTALLED, 213
ITC_NVPARM_MANF_DATE, 212
ITC_NVPARM_MCODE, 212
ITC_NVPARM_RTC_RESTORE, 212
ITC_NVPARM_SERIAL_NUM, 212
ITC_NVPARM_SERIAL2_INSTALLED, 213
ITC_NVPARM_SERVICE_DATE, 212
ITC_NVPARM_SIM_PROTECT_HW_INSTALLED, 213
ITC_NVPARM_SIM_PROTECT_SW_INSTALLED, 213
ITC_NVPARM_VERSION_NUMBER, 212
ITC_NVPARM_VIBRATE_INSTALLED, 213
ITC_NVPARM_WAN_FREQUENCY, 213
ITC_NVPARM_WAN_INSTALLED, 213
ITC_NVPARM_WAN_RADIOTYPE, 213
ITC_NVPARM_WAN_RI, 212
IOCTL_HAL_ITC_WRITE_SYSPARM
ITC_ DOCK_SWITCH, 214
ITC_ WAKEUP_MASK, 215
ITC_AMBIENT_FRONTLIGHT, 215
ITC_AMBIENT_KEYBOARD, 215
ITC_REGISTRY_SAVE_ENABLE, 214
IDNA
DeviceName, 204
DeviceURL, 204
IDNATarget, FTP Server, 204
InstallDir, [CEStrings], 189
Intermec Device Network Announcement. See IDNA
IOCTL_GET_CPU_ID, 220
IOCTL_HAL_COLDBOOT, 217, 222
IOCTL_HAL_GET_BOOT_DEVICE, 219
IOCTL_HAL_GET_BOOTLOADER_VERINFO, 216
IOCTL_HAL_GET_DEVICE_INFO, 210
IOCTL_HAL_GET_DEVICEID, 215
IOCTL_HAL_GET_OAL_VERINFO, 216
IOCTL_HAL_GET_RESET_INFO, 218
IOCTL_HAL_ITC_READ_PARM, 211
IOCTL_HAL_ITC_WRITE_SYSPARM, 214
IOCTL_HAL_REBOOT, 219, 222
IOCTL_HAL_WARMBOOT, 217, 222
IOCTL_PROCESSOR_INFORMATION, 220
ITC_ DOCK_SWITCH, 214
ITC_ WAKEUP_MASK, 215
ITC_AMBIENT_FRONTLIGHT, 215
ITC_AMBIENT_KEYBOARD, 215
ITC_DEVID_80211RADIO_INTEL_2011B, 213
ITC_DEVID_80211RADIO_MAX values
ITC_DEVID_80211RADIO_INTEL_2011B, 213
ITC_DEVID_80211RADIO_NONE, 213
ITC_DEVID_80211RADIO_NONE, 213
ITC_DEVID_INTERMEC_EVIO, 213
ITC_DEVID_INTERMEC2D_IMAGER, 213
ITC_DEVID_OEM2D_IMAGER, 213
263
Index
ITC_DEVID_SCANHW_MAX values
ITC_DEVID_INTERMEC_EVIO, 213
ITC_DEVID_INTERMEC2D_IMAGER, 213
ITC_DEVID_OEM2D_IMAGER, 213
ITC_DEVID_SCANHW_NONE, 213
ITC_DEVID_SE900_LASER, 213
ITC_DEVID_SE900HS_LASER, 213
ITC_DEVID_SCANHW_NONE, 213
ITC_DEVID_SE900_LASER, 213
ITC_DEVID_SE900HS_LASER, 213
ITC_DEVID_WANRADIO_NONE, 213
ITC_DEVID_WANRADIO_SIEMENS_MC45, 213
ITC_DEVID_WANRADIO_SIEMENS_MC46, 213
ITC_DEVID_WANRADIO_SIERRA_SB555, 213
ITC_DEVID_WANRADIO_XIRCOM_GEM3503, 213
ITC_IFTP_STOP, 208
ITC_NVPARM_80211_INSTALLED, 213
ITC_NVPARM_80211_RADIOTYPE, 213
ITC_NVPARM_ANTENNA_DIVERSITY, 212
ITC_NVPARM_BLUETOOTH_INSTALLED, 213
ITC_NVPARM_CONTRAST, 212
ITC_NVPARM_DISPLAY_TYPE, 212
ITC_NVPARM_ECN, 212
ITC_NVPARM_EDBG_SUBNET, 212
ITC_NVPARM_EDG_IP, 212
ITC_NVPARM_ETHERNET_ID, 212
ITC_NVPARM_INTERMEC_DATACOLLECTION_HW, 213
ITC_NVPARM_INTERMEC_DATACOLLECTION_SW, 212
ITC_NVPARM_INTERMEC_SOFTWARE_CONTENT, 212
ITC_NVPARM_LAN9000_INSTALLED, 213
ITC_NVPARM_MANF_DATE, 212
ITC_NVPARM_MCODE, 212
ITC_NVPARM_RTC_RESTORE, 212
ITC_NVPARM_SERIAL_NUM, 212
ITC_NVPARM_SERIAL2_INSTALLED, 213
ITC_NVPARM_SERVICE_DATE, 212
ITC_NVPARM_SIM_PROTECT_HW_INSTALLED,
213
ITC_NVPARM_SIM_PROTECT_SW_INSTALLED,
213
ITC_NVPARM_VERSION_NUMBER, 212
ITC_NVPARM_VIBRATE_INSTALLED, 213
ITC_NVPARM_WAN_FREQUENCY, 213
ITC_NVPARM_WAN_INSTALLED, 213
ITC_NVPARM_WAN_RADIOTYPE, 213
ITC_NVPARM_WAN_RI, 212
ITC_REGISTRY_SAVE_ENABLE, 214
KernelIoControl
IOCTL_GET_CPU_ID, 220
IOCTL_HAL_COLDBOOT, 217, 222
IOCTL_HAL_GET_BOOT_DEVICE, 219
IOCTL_HAL_GET_BOOTLOADER_VERINFO,
216
IOCTL_HAL_GET_DEVICE_INFO, 210
IOCTL_HAL_GET_DEVICEID, 215
264
IOCTL_HAL_GET_OAL_VERINFO, 216
IOCTL_HAL_GET_RESET_INFO, 218
IOCTL_HAL_ITC_READ_PARM, 211
IOCTL_HAL_ITC_WRITE_SYSPARM, 214
IOCTL_HAL_REBOOT, 219, 222
IOCTL_HAL_WARMBOOT, 217, 222
IOCTL_PROCESSOR_INFORMATION, 220
KernelIoControl(), 210
lpBytesReturned
IOCTL_GET_CPU_ID, 221
IOCTL_HAL_GET_BOOT_DEVICE, 219
IOCTL_HAL_GET_BOOTLOADER_VERINFO,
217
IOCTL_HAL_GET_DEVICE_INFO, 211
IOCTL_HAL_GET_DEVICEID, 215
IOCTL_HAL_GET_OAL_VERINFO, 216
IOCTL_HAL_GET_RESET_INFO, 218
IOCTL_HAL_ITC_READ_PARM, 211
IOCTL_HAL_ITC_WRITE_SYSPARM, 214
IOCTL_PROCESSOR_INFORMATION, 220
lpInBuf
IOCTL_GET_CPU_ID, 220
IOCTL_HAL_COLDBOOT, 218
IOCTL_HAL_GET_BOOT_DEVICE, 219
IOCTL_HAL_GET_BOOTLOADER_VERINFO,
216
IOCTL_HAL_GET_DEVICE_INFO, 211
IOCTL_HAL_GET_DEVICEID, 215
IOCTL_HAL_GET_OAL_VERINFO, 216
IOCTL_HAL_GET_RESET_INFO, 218
IOCTL_HAL_ITC_READ_PARM, 211
IOCTL_HAL_ITC_WRITE_SYSPARM, 214
IOCTL_HAL_REBOOT, 219
IOCTL_HAL_WARMBOOT, 217
IOCTL_PROCESSOR_INFORMATION, 220
lpInBufSize
IOCTL_GET_CPU_ID, 220
IOCTL_HAL_COLDBOOT, 218
IOCTL_HAL_GET_BOOT_DEVICE, 219
IOCTL_HAL_GET_DEVICE_INFO, 211
IOCTL_HAL_GET_DEVICEID, 215
IOCTL_HAL_GET_OAL_VERINFO, 216
IOCTL_HAL_GET_RESET_INFO, 218
IOCTL_HAL_REBOOT, 219
IOCTL_HAL_WARMBOOT, 217
lpOutBuf
IOCTL_GET_CPU_ID, 221
IOCTL_HAL_COLDBOOT, 218
IOCTL_HAL_GET_BOOT_DEVICE, 219
IOCTL_HAL_GET_BOOTLOADER_VERINFO,
217
IOCTL_HAL_GET_DEVICE_INFO, 211
IOCTL_HAL_GET_DEVICEID, 215
IOCTL_HAL_GET_OAL_VERINFO, 216
IOCTL_HAL_GET_RESET_INFO, 218
IOCTL_HAL_ITC_READ_PARM, 211
IOCTL_HAL_ITC_WRITE_SYSPARM, 214
IOCTL_HAL_REBOOT, 219
700 Series Color Mobile Computer User’s Manual
Index
IOCTL_HAL_WARMBOOT, 217
IOCTL_PROCESSOR_INFORMATION, 220
ManifestName, FTP Server, 205
nDeviceId, NLEDGetDeviceInfo, 222
nInBufSize
IOCTL_HAL_GET_BOOTLOADER_VERINFO,
216
IOCTL_HAL_ITC_READ_PARM, 211
IOCTL_HAL_ITC_WRITE_SYSPARM, 214
IOCTL_PROCESSOR_INFORMATION, 220
nInfoId, NLEDGetDeviceInfo, 222
NLED_COUNT_INFO, NLEDGetDeviceInfo, 222
NLED_SETTINGS_INFO_ID, NLEDGetDeviceInfo,
222
NLED_SUPPORTS_INFO_ID, NLEDGetDeviceInfo,
222
NLEDGetDeviceInfo, 221
NLEDSetDevice, 222
nOutBufSize
IOCTL_GET_CPU_ID, 221
IOCTL_HAL_COLDBOOT, 218
IOCTL_HAL_GET_BOOT_DEVICE, 219
IOCTL_HAL_GET_BOOTLOADER_VERINFO,
217
IOCTL_HAL_GET_DEVICE_INFO, 211
IOCTL_HAL_GET_DEVICEID, 215
IOCTL_HAL_GET_OAL_VERINFO, 216
IOCTL_HAL_GET_RESET_INFO, 218
IOCTL_HAL_ITC_READ_PARM, 211
IOCTL_HAL_ITC_WRITE_SYSPARM, 214
IOCTL_HAL_REBOOT, 219
IOCTL_HAL_WARMBOOT, 217
IOCTL_PROCESSOR_INFORMATION, 220
Object store
IOCTL_HAL_COLDBOOT, 217
IOCTL_HAL_REBOOT, 219
IOCTL_HAL_WARMBOOT, 217
Oldstyle device ID, 215
OSVERSIONINFO.dwBuildNumber, 190
OSVERSIONINFO.dwVersionMajor, 190
OSVERSIONINFO.dwVersionMinor, 190
PauseAtStartup, FTP Server, 205
pInput, NLEDSetDevice, 222
Pocket PC
IOCTL_HAL_GET_BOOTLOADER_VERINFO,
216
IOCTL_HAL_GET_OAL_VERINFO, 216
pOutput, NLEDGetDeviceInfo, 222
Processor information, IOCTL_PROCESSOR_INFORMATION, 220
ProcessorType, [CEDevice], 189
700 Series Color Mobile Computer User’s Manual
Provider, [Version], 188
ReadFile(), NPCP printing, 163
Reboot methods
IOCTL_HAL_COLDBOOT, 222
IOCTL_HAL_REBOOT, 222
IOCTL_HAL_WARMBOOT, 222
RegFlushKey(), 202
RegisterDevice(), 163
DTR printing, 167
Registry
FTP Server parameters, 204
save location, IOCTL_HAL_ITC_WRITE_SYSPARM,
214
RegOpenKeyEx(), 224
RegQueryValueEx(), 224
RegSetValueEx(), 224
RFC 959, 208
Root, FTP Server, 205
SHFullScreen(), 202
shortcut_list_section, [CEShortcuts]
shortcut_filename, 194
shortcut_type_flag, 194
target_file/path, 195
target_file_path, 195
Signature, [Version], 188
SIM cards
protection hardware, 213
software installed, 213
[SourceDiskFiles], filename, 192
[SourceDiskNames]
CESignature, 191
disk_ordinal, 191
SourceDisksNames.MIPS, 192
SourceDisksNames.SH3, 192
string_key, [Strings], 189
[Strings], string_key, 189
SYSTEMINFO.dwProcessorType, 189
UDP, FTPDCE, 205
UDP broadcasts, IDNATarget parameter, 204
UnsupportedPlatforms, [CEDevice], 189
UUID, 215
[Version]
CESignature, 188
Provider, 188
Signature, 188
VersionMax, [CEDevice], 190
VersionMin, [CEDevice], 190
VN_CLASS_ASIC, 212
VN_CLASS_BOOTSTRAP, 212
VN_CLASS_KBD, 212
265
Index
WAN radio IDs
ITC_DEVID_WANRADIO_NONE, 213
ITC_DEVID_WANRADIO_SIEMENS_MC45, 213
ITC_DEVID_WANRADIO_SIEMENS_MC46, 213
ITC_DEVID_WANRADIO_SIERRA_SB555, 213
Warm boot
IOCTL_HAL_REBOOT, 219
266
IOCTL_HAL_WARMBOOT, 217
Wireless TCP/IP installations, BlockSize parameter, 204
WriteFile()
DTR printing, 167, 168
IrDA printing, 162
NPCP printing, 163, 164
Xscale processor ID, IOCTL_GET_CPU_ID, 220
700 Series Color Mobile Computer User’s Manual
Index
General Index
Numbers
1551/1553 Tethered Scanner
configuring, 177
intermec settings, 177
reset to factory defaults, 180
troubleshooting, 179
1D area imager reading distances, 173
1D laser scanner, about, 169
2D area imager reading distances, 176
2D Imager, about, 169
4820 printer, NPCP driver, 163
6804DM printer, IrDA driver, 162
6804T printer, IrDA driver, 162
6805A printer, IrDA driver, 162
6806 printer, IrDA driver, 162
6808 printer
IrDA driver, 162
printer support, 161
6820 printer
IrDA driver, 162
NPCP driver, 163
printer support, 161
6920 Communications Server, ManifestName parameter,
205
740 Color Computer, 223
782T printer, printer support, 161
802.11
antenna color code, 98
channel, 237
communications setup, 108, 236
EAP-FAST
network EAP, 250
WPA encryption, 250
LEAP
network EAP, 248
WPA encryption, 248
network type, 237
PEAP
network EAP, 241
WPA encryption, 240
profile label, 237
profile security information, WEP encryption, 239
profiles, 237
advanced settings, 252
basic information, 237
security information, 238
SSID (network name), 237
TTLS, WPA encryption, 245
WPA authentication, Zero Configuration, 114
WPA authentication with pre-shared key, Zero Configuration, 114
WPA encryption, 239
zero configuration, WEP encryption, 113
700 Series Color Mobile Computer User’s Manual
AB10 battery
low battery conditions, 2
RAM maintenance, 3
status, 2
Abstract Syntax Notation.1. See ASN.1
Accessory list, 21
Accounts, via Inbox, 66
Activation wizard
Phone application, CDMA radios, 122
phone application, CDMA radios, 117, 119
ActiveSync
ActiveSync Help, 42
adding programs, 38
adding programs to Start menu, 40
Folder behavior connected to e-mail server, 64
installing applications, 87
Microsoft Reader, 77
Pocket Internet Explorer
favorite links, 80
mobile favorites, 80
Mobile Favorites folder, 80
replicating registry settings, 89
Start menu icon, 27
URL, 41
Windows Mobile, 41
Adding bookmarks, Microsoft Reader, 79
Adding drawings to text, Microsoft Reader, 79
Adding programs
ActiveSync, 38
Pocket Internet Explorer, 40
to the Start menu, 40
via ActiveSync, 40
via File Explorer, 40
Windows Mobile, 38
Adjusting settings, Windows Mobile, 38
Adobe Acrobat Reader, URL, 144
All-Day events, Calendar, 44
creating, 48
Alpha plane on keypad, 224
Alphanumeric keypad
alpha (blue) key sequences, 13
[gold/white] key sequences, 12
registry settings
alpha plane, 224
gold plane, 224
unshifted plane, 224
scan codes, 227
Ambient lighting, 4
Annotations index, Microsoft Reader, 79
Antenna, radio type, 98
APIs
AT command interface, 143
IrSock, 162
network selection, 221
App launch, utilities applet, 234
267
Index
Applets
Audio, 7
backlight, 4, 10
clock, 255
intermec settings, 9, 231
beeper volume, 8
internal scanners, 171
RFID, 184
scan buttons, 182
tethered scanners, 177
vibrator, 20
phone settings
CDMA radios, 123
GSM radios, 128
power
battery status, 2
RAM maintenance, 3
system, wireless network, 108, 236
utilities, 231
app launch, 234
dock switch, 232
registry save, 232
wakeup mask, 233
wireless network, 235
Application keys, utilities applet
app launch, 234
wakeup mask, 233
Appointments
Calendar
adding a note, 49
assigning to a category, 50
changing, 47
creating, 47
deleting, 53
finding, 52
making recurring, 50
setting a reminder, 48
viewing, 46
via Calendar, 42
APS linear imager, about, 169
ASCII
printing, 162
printing to a port, port print method, 162
raw text to printer, 162
ASN.1, 157
AT command interface, 143
testing, 144
Attaching notes to text, Microsoft Reader, 79
Audio applet, input mixing, 7
Audio files, Windows Media Player, 76
Audio system
external headset jack, 6
microphone, 5
speaker, 5
AutoCab, command line syntax, 95
AutoFTP, 209
AutoIP, 116
Automatic Private IP. See AutoIP
268
Automatic shutoff
bar code configuration, 253, 256
configuration parameter, 253
Autostart FTP, 209
AvantGo channels, Pocket Internet Explorer, 81
Backlight applet
ambient light sensor, 4
keypad, 10
Backlight timeout
bar code configuration, 253, 256
configuration parameter, 253
Bar code configuration
audio volume, 253
automatic shutoff, 253
backlight timeout, 253
key clicks, 253
Bar codes
configuration
audio volume, 255
automatic shutoff, 256
backlight timeout, 256
Code 39, 255
key clicks, 257
internal scanner supported symbologies, 172
scanning labels, 255
tethered scanner supported symbologies, 180
Battery
ambient lighting, 4
low battery conditions, 2
RAM maintenance, 3
specifications, 23
status, 2
Beeper
silencing the volume, 9
volume, turning it on, 7
Bell Mobility activation process, 143
Block recognizer, Windows Mobile input panel, 31
Bluetooth
accessing, 100, 103
activating, 100, 103
disable power, 183
WPport, 101
Bluetooth compatibility, network support, 99
Books, Microsoft Reader
adding bookmarks, 79
adding drawings, 79
annotations index, 79
attaching notes, 79
copying, 79
downloading, 77
highlighting, 79
reading, 78
removing, 79
searching, 79
Browsing the Internet, Pocket Internet Explorer, 83
Build information, software, 17
700 Series Color Mobile Computer User’s Manual
Index
CAB files
after the extraction, 198
creating, 188
INF files, 188
with CAB Wizard, 201
installation functions, SETUP.DLL, 197
Cabinet Wizard
creating CAB files, 201
troubleshooting, 201
using the application, 188
Calendar
all day events, 44
creating, 48
appointments
adding a note, 49
assigning to a category, 50
changing, 47
creating, 47
deleting, 53
finding, 52
making recurring, 50
setting a reminder, 48
viewing, 46
categories, 43
meetings, sending a request, 51
options, changing, 53
Pocket Outlook, 42
recurrence pattern, 45
Start menu icon, 27
synchronizing, 43
Call Guard alert, enable while roaming, Phone application,
CDMA radios, 125
Call history, Phone application
CDMA radios, 122
GSM radios, 126
Capacitor, internal super, 2
Capturing thoughts and ideas, via Notes, 62
Card support
CompactFlash cards, 18
card slots, 19
MultiMediaCards, 18
radios, 21
Secure Digital cards, 18
card slots, 19
pull tabs, 19
SIM cards, 18
card slots, 19
Carrier, location of ESN, 133
Categories
calendar, 43
contacts, assigning to, 57
CDMA/1xRTT
activation with SB555 Watcher, 133
Bell Mobility, 143
Sprint, 137
Telus, 143
Verizon, 135
antenna color code, 98
700 Series Color Mobile Computer User’s Manual
AT command set, 144
copying files from web site, 131
via Microsoft ActiveSync, 131
via storage cards, 131
location of ESC, 133
phone activation, 117, 119
phone application, 117
setting up, 130
terminology, 130
Channel, 802.11 radio module, 237
Cisco compatible extension specifications, 21
Clock
restore real-time after cold-boot, 233
setting date and time, 255
Windows Mobile settings, 38
Closing drivers, NPCP, 164
Cold boot, performing, 16
COM A, modem position, 232
COM B, serial position, 232
COM1, NPCP parameter, 163
COM1 port, 162
Command line syntax, AutoCab, 95
Communications
DTR, 168
NPCP, 165
CompactFlash cards
card slots, 19
card support, 18
installing applications, 88
packaging an application, 86
specifications, 22
Computer shutdown, 2
Configuration parameters
automatic shutoff, 253
backlight timeout, 253
date/time, 253
key clicks, 253
volume, 253
Configuring service settings, Phone application, GSM radios, 128
Connecting to
an ISP, 148
work, 151
Connecting to a mail server, via Inbox, 65
Connections
See also Getting connected
ending, 156
to an ISP, 148
via modem, 148
to work, 151
via modem, 152
via VPN server, 154
via modem
to an ISP, 148
to work, 152
via VPN server, to work, 154
via wireless network, 111
Conserving battery power, 4
269
Index
Contacts
adding a note, 56
adding a telephone number
CDMA radios, 121
GSM radios, 127
adding to speed dial, 59
assigning to a category, 57
changing, 56
changing options, 59
copying, 57
creating, 54, 56
deleting, 59
finding, 58
MSN Messenger
managing, 75
sending messages, 76
working with, 75
Pocket Outlook, 53
sending a message, 58
Start menu icon, 27
synchronizing, 55
viewing, 55
Converting writing to text, 33
Copying, contacts, 57
Copying text, Microsoft Reader, 79
Creating
a modem connection
to an ISP, 148
to work, 152
a VPN server connection, to work, 154
a wireless network connection, 111
CAB files, 188
with CAB Wizard, 201
contacts via Contacts, 54
document via Pocket Word, 68
drawing via Notes, 35
INF files, 188
note via Notes, 62
task via Tasks, 61
workbook via Pocket Excel, 72
Data, Phone application, CDMA radios, 124
Date, setting, 255
Date/Time, configuration parameter, 253
DHCP, 116
replicating registry settings, 88
Display full screen, 202
Display specifications, 21
Dock switch, utilities applet, 232
Docks, modem support, 15
DRAM
low battery shutdown, 3
maintenance, 3
Drawing mode, Pocket Word, 70
Drawing on the screen
See also Notes
Pocket Word, 70
270
Drivers
DTR
communications, 168
installing, 167
opening, 167
removing, 167
writing to, 168
NPCP
closing, 164
communications, 165
I/O controls, 164
installing, 163
opening, 164
reading from, 164
removing, 163
writing to, 164
O’Neil. See DTR printing
DTR printing, 167
closing driver, 168
communications, 168
opening driver, 167
removing driver, 167
writing to driver, 168
EAP-FAST
802.11 radio module
network EAP, 250
WPA encryption, 250
profile security information, 249
WEP encryption, 249
Editing a profile, 237
EL10, about the laser scanner, 169
Emails, SMS messages via Phone application
CDMA radios, 123
GSM radios, 127
Ending a connection, 156
Environmental specifications, 22
Epson Escape Sequences, 162
ESN, location on computer, 133
Ethernet, communications setup, 109
ETSI GSM 07.05 interface specifications, 143
ETSI GSM 07.07 interface specifications, 143
Expansion slot specifications, 22
Favorite links, Pocket Internet Explorer, 80
File Explorer
adding programs to Start menu, 40
removing programs, 40
Windows Mobile, 37
Find feature, Windows Mobile, 37
Flash File Store, packaging an application, 86
Flash file system, utilities applet, registry save, 232
Folder behavior connected to e-mail server
ActiveSync, 64
IMAP4, 65
POP3, 65
SMS, 65
700 Series Color Mobile Computer User’s Manual
Index
FRAME_NOT_ACKED, 165
FTP
configurable parameters
IDNATarget, 204
ManifestName, 205
Root, 205
heartbeat, 205
server, installing applications, 88
FTPDCMDS subdirectory, FTP support, 208
Full screen display, 202
GDI approach, 162
Getting connected
ISP, 148
to an ISP, 148
creating a modem connection, 148
to work, 151
creating a modem connection, 152
creating a VPN server connection, 154
creating a wireless network connection, 111
Windows Mobile, 103, 148
Gold plane on keypad, 223
GSM/GPRS
antenna color code, 98
AT command set
MC45, 144
MC46, 144
MC75, 144
phone application, 125
Headset jack, external, 6
Hex values, 236
Hiding your location from everyone except 911, CDMA
radios, 124
Highlighting text, Microsoft Reader, 79
I/O controls, NPCP driver, 164
IDLs
Bluetooth, 99
data collection, 9, 157, 170, 231
device, 210, 222
network selection APIs, 221
printing, 162
smartsystems foundation, 94
URL, 17
IDNA
IDNATarget, 204
ManifestName, 205
Imager, vibrator, enabling, 20
IMAP4, Folder behavior connected to e-mail server, 65
Inbox
accounts, 66
composing/sending messages, 66
connecting to a mail server, 65
downloading messages from server, 66
getting connected, 148
managing e-mail messages and folders, 64
700 Series Color Mobile Computer User’s Manual
Pocket Outlook, 63
Start menu icon, 28
synchronizing e-mail messages, 64
using My Text, 36
INF files, creating, 188
Input Mixing, audio applet, 7
Input panel
block recognizer, 31
keyboard, 30
letter recognizer, 32
Pocket Word, 69
selecting typed text, 32
transcriber, 32
Windows Mobile, 28
word suggestions, 30
Installation functions, SETUP.DLL, 197
Installing applications
using a storage card, 88
using storage cards, 88
with ActiveSync, 87
with FTP Server, 88
Installing drivers
DTR, 167
NPCP, 163
Instant messaging, 73
Integrated scanners. See Internal scanners
Interface specifications, ETSI GSM 07.0x, 143
Intermec Developer Library. See IDLs
Intermec part numbers, 21
Intermec Settings applet, 9, 231
beeper volume, 8
data collection
internal scanners, 171
tethered scanners, 177
device settings, scan buttons, 182
PB42 printers, 168
RFID, 184
vibrator, 20
Internal scanners
configuring, 171
intermec settings, 171
reading distances
2D area imager, 176
EA10, 173
EA11, 174
EL10, 175
EL11, 175
EV10, 176
specifications, 22
supported symbologies, 172
Internet Explorer, software build version, 17
Internet Service Provider. See ISP
IOCTL_NPCP_BIND, 165
IOCTL_NPCP_CANCEL, 165
IOCTL_NPCP_CLOSE, 165
IOCTL_NPCP_ERROR, 165
IOCTL_NPCP_FLUSH, 165
IP address, replicating registry settings, 89
IP4 readers, 181
configuring, 184
271
Index
IrDA printing, 162
ISP
connecting to via Windows Mobile, 148
creating, a modem connection, 148
Pocket Internet Explorer, 79
Windows Mobile, 148
ITC_KEYBOARD_CHANGE, CreateEvent(), 225
ITU-T interface specifications, 143
Keeping a to-do list, via Tasks, 60
Key clicks
bar code configuration, 253, 257
configuration parameter, 253
Key sequences
alpha (blue) keys
alphanumeric, 13
numeric, 12
[gold] keys, numeric, 11
[gold/white] keys, alphanumeric, 12
Keyboard
See also Keypad
Windows Mobile input panel, 30
Keypad
advanced remapping, 225
alphanumeric
alpha (blue) key sequences, 13
[gold/white] key sequences, 12
scan codes, 227
backlight applet, 10
change notification, 225
driver registry settings, 224
numeric
alpha (blue) key sequences, 12
[gold] key sequences, 11
scan codes, 226
planes, 223
remapping, 223
sample registry keys, 228
specifications, 22
Laser scanner, configuration parameters, 230
LEAP
802.11 radio module
network EAP, 248
WPA encryption, 248
profile security information, 247
WEP encryption, 247
LED status, 14
battery, 14
scanning keypad/shift and notification, 15
Letter recognizer, Windows Mobile input panel, 32
Letting your location be visible, CDMA radios, 124
Library, Microsoft Reader, 78
272
Line printing, 162
Location, Phone application, CDMA radios, 124
LPT9 printer device, 163
Managing e-mail messages and folders, via Inbox, 64
MC75 radio radome, 99
Meetings
Calendar, sending a request, 51
via Calendar, 42
Memory and storage, specifications, 22
Menus, Windows Mobile settings, 38
Messages
sending to, contacts, 58
via Inbox
composing/sending, 66
downloading from server, 66
MIBs
ASN.1, 157
files, 157
object identifier, 158
Micro Electro Mechanical System (MEMS), 169
Microphone, 5
Microprocessor, specifications, 22
Microsoft Developer Network Library. See MSDN library
Microsoft Exchange e-mail account, 73
Microsoft Passport account, 73
Microsoft Reader
books
downloading, 77
reading, 78
removing, 79
features, 79
adding bookmarks, 79
adding drawings, 79
annotations index, 79
attaching notes, 79
copying text, 79
highlighting text, 79
searching for text, 79
using the library, 78
Windows Mobile, 77
Microsoft’s Wireless Zero Config, 237
Migrating to a 700 Color Computer, 95
Mobile Favorites, Pocket Internet Explorer, 80
Mobile Favorites folder, Pocket Internet Explorer, 80
Modem position, COM A, 232
Modems
creating a connection
to an ISP, 148
to work, 152
specifications, 22
MP3 files, Windows Media Player, 77
MSDN library, 209
MSDN Windows CE documentation, 116
700 Series Color Mobile Computer User’s Manual
Index
MSN Messenger
accounts
Microsoft Exchange e-mail, 73
Microsoft Passport, 73
contacts
managing, 75
sending messages, 76
working with, 75
setting up an account, 74
using My Text, 36
MultiMediaCards, card support, 18
Network adapters
antenna color code, 98
Ethernet communications, 109
no networking, 110
wireless 802.11, 110
wireless printing, 99
Network EAP
EAP-FAST security method, 250
LEAP security method, 248
PEAP security method, 241
Network selection APIs, 221
Network settings, Phone application, GSM radios, 129
Network type, 802.11 radio module, 237
NLED driver, vibrator, 221
NLED_SETTINGS_INFO_ID, NLEDSetDevice, 222
Notes
adding to
appointments, 49
contacts, 56
creating a note, 62
drawing on the screen, 35
creating a drawing, 35
selecting a drawing, 35
Pocket Outlook, 62
recording a message, 36
Start menu icon, 28
synchronizing notes, 63
writing on the screen, 32
alternate writing, 34
converting writing to text, 33
selecting the writing, 33
tips for good recognition, 34
NPCP printing, 163
about, 163
closing driver, 164
COM1 parameters, 163
communications, 165
driver I/O controls, 164
installation, 163
LPT9, 163
opening driver, 164
reading from driver, 164
removal, 163
sample code, 166
writing to driver, 164
Numeric keypad
alpha (blue) key sequences, 12
700 Series Color Mobile Computer User’s Manual
[gold] key sequences, 11
registry settings
alpha plane, 224
gold plane, 224
unshifted plane, 224
scan codes, 226
O’Neil printing
See also DTR printer
installing driver, 167
Object Store, packaging an application, 86
Opening drivers
DTR, 167
NPCP, 164
Operating system, specifications, 23
Owner information, Windows Mobile settings, 38
Packaging an application
CompactFlash storage cards, 86
Flash File Store, 86
Object Store, 86
Persistent Storage Manager, 86
Secure Digital storage cards, 86
Page format printing, 162
Password
Pocket Excel, 72
Windows Mobile settings, 38
Patent information, xvii
PB20 printers, printer support, 161
PB42 printers
intermec settings applet, 168
printer support, 161
PDF417, about the laser scanner, 169
PEAP
802.11 radio module
network EAP, 241
WPA encryption, 240
profile security information, 240
WEP encryption, 240
Performing a cold boot, 16
Performing a warm boot, 16
Persistent Storage Manager. See PSM
Phone application
CDMA radios, 117
activation wizard, 117, 119, 122
adding contact to speed dial, 59, 121
call history, 122
customizing phone settings, 123
enable Call Guard alert while roaming, 125
hiding your location except from 911, 124
letting your location be visible for everyone, 124
reset connection settings for PCS Vision, 124
sending SMS messages, 123
toggle between automatic or Sprint roaming, 125
update your PCS Vision profile, 124
view current phone settings, 125
voice mail, 122
273
Index
GSM radios, 125
adding contact to speed dial, 127
call history, 126
customizing phone settings, 128
finding, setting, selecting networks, 129
sending SMS messages, 127
service settings, 128
view current phone settings, 130
Phone Info
Phone application, CDMA radios, 125
WAN info, GSM radios, 130
Phone jack position, utilities applet, dock switch, 232
Phone Settings applet
CDMA radios, 123
customizing via Phone application
CDMA radios, 123
GSM radios, 128
GSM radios, 128
network settings, GSM radios, 129
view current settings via Phone application, CDMA
radios, 125
view current settings via WAN info, GSM radios, 130
Physical dimensions, specifications, 23
Planes, keypad, 223
Pocket Excel
about, 71
creating a workbook, 72
Pocket Internet Explorer
about, 79
adding programs, 40
AvantGo channels, 81
browsing the Internet, 83
favorite links, 80
getting connected, 148
mobile favorites, 80
Mobile Favorites folder, 80
software build, 17
Start menu icon, 28
viewing mobile favorites and channels, 82
Pocket Outlook, Calendar, 42
Pocket Word
about, 68
creating a document, 68
drawing mode, 70
recording mode, 70
synchronizing, 71
tips, 72
typing mode, 69
writing mode, 70
POP3, Folder behavior connected to e-mail server, 65
Power, Windows Mobile settings, 38
Power applet
battery status, 2
RAM maintenance, 3
specifications, 23
Printer support, 162
IrDA printer driver, 162
NPCP printer driver, 163
O’Neil printer driver, 167
Profile label, 802.11 radio module, 237
274
Profiles
802.11 radio module, 237
advanced settings, 252
basic information, 237
security information, 238
editing, 237
Programs, adding or removing, Windows Mobile, 38
PSM
determining build version, 15
packaging an application, 86
Radios
See also Network adapters
card support, 21
Radome (761B computers), 99
Reader commands, 254
configuration change, 254
date and time settings, 255
Reading distances
2D area imager, 176
EA10, 173
EA11, 174
EL10, 175
EL11, 175
EV10, 176
Reading from drivers, NPCP, 164
Real-Time Clock, restore after cold-boot, 233
Record button, recording a message, 36
Recording, via Notes, 36
Recording a message, Pocket Word, 70
Recording mode, Pocket Word, 70
Recovery CD
AutoCab method, 95
RegFlushKey() API, 202
updating the system software, 92
Recurrence pattern, Calendar, 45
Registry
confirm the new regisry file, 90
copy the REGFLUSH.CAB file, 89
delete the old registry save, 89
keypad remapping, 224
load the application, 90
replicating settings, 88
sample view of key mapping, 228
update other computers, 91
Registry Save, utilities applet, 232
Registry settings
AutoCfg, 116
AutoFTP, 209
AutoInterval, 116
AutoIP/DHCP, 116
DhcpMaxRetry, 116
DhcpRetryDialogue, 116
EnableDHCP, 116
keypad driver, 224
keypad planes
alpha, 224
gold, 224
unshifted, 224
700 Series Color Mobile Computer User’s Manual
Index
Regulatory approvals, specifications, 23
Removing drivers
DTR, 167
NPCP, 163
Removing programs, Windows Mobile, 38, 40
Replicating registry settings, 88
Reset button, 16
Reset connection settings for PCS Vision, Phone application, CDMA radios, 124
Resource kits
Bluetooth, 99
data collection, 9, 157, 170, 231
device, 210, 222
printing, 162
smartsystems foundation, 94
URL, 17
RFID readers, 181
configuring, 184
intermec settings, 184
Roaming, toggle between automatic or Sprint, Phone application, CDMA radios, 125
RTC. See Real-Time Clock
Sample code, NPCP printing, 166
SB555 Watcher
activation, 133
Bell Mobility, 143
Sprint, 137
Telus, 143
Verizon, 135
copying files to computer, 131
via Microsoft ActiveSync, 131
via storage cards, 131
location of ESN, 133
Scan codes
alphanumeric keypad, 227
numeric keypad, 226
SCAN Mute, audio applet, 7
Scanner
beeper volume
turning it off, 9
turning it on, 7
mute feature, turning it off, 7
specifications, 22
unit configuration parameters
automatic shutoff, 253
backlight timeout, 253
date/time, 253
key clicks, 253
volume, 253
utilities configuration, button wakeup mask, 233
Scheduling appointments and meetings, via Calendar, 42
Searching for text, Microsoft Reader, 79
Secure Digital cards
card slots, 19
card support, 18
installing applications, 88
packaging an application, 86
700 Series Color Mobile Computer User’s Manual
pull tabs, 19
specifications, 22
upgrading computer, 93
Selecting, drawing via Notes, 35
Sending and receiving messages, via Inbox, 63
Serial port, modem support, 15
Serial position, COM B, 232
Services, Phone application, GSM radios, 128
Setting date and time, 255
SETUP.DLL, installation functions, 197
SIM cards
card slots, 19
card support, 18
Simple Network Management Protocol. See SNMP
SmartSystems, upgrading computer, 94
SMS, Folder behavior connected to e-mail server, 65
SMS messages, Phone application
CDMA radios, 123
GSM radios, 127
Snap-on modems, 15
SNMP, 157
Software versions, 700 Series Computer, 17
Speaker, 5
Specifications, 21
Cisco compatible extensions, 21
display, 21
environmental, 22
expansion slots, 22
integrated scanner options, 22
integrated wireless, 22
keypad options, 22
memory and storage, 22
microprocessor, 22
modems, 22
operating system, 23
physical dimensions, 23
power, 23
regulatory approvals, 23
standard communications, 23
Speed dial, Phone application
CDMA radios, 121
GSM radios, 127
Sprint activation process, 137
SSID (network name), 802.11 radio module, 237
Standard communications, specifications, 23
Start Menu, adding programs, 40
via ActiveSync, 40
via File Explorer, 40
Static IP, replicating registry settings, 88
Status icons, Windows Mobile, 27
Storage media, 18
specifications, 22
Stream device driver
NPCPPORT.DLL, 163
ONEIL.DLL, 167
Symbologies
internal scanner supported symbologies, 172
scanning labels, 255
tethered scanner supported symbologies, 180
275
Index
Synchronizing
AvantGo channels, 81
Calendar, 43
contacts, 55
e-mail messages, 64
favorite links, 80
mobile favorites, 80
notes, 63
Pocket Word, 71
Tasks, 61
System, Phone application, CDMA radios, 125
Tasks
creating a task, 61
Pocket Outlook, 60
Start menu icon, 28
synchronizing, 61
TCP/IP client, DHCP server, 116
Telus activation process, 143
Testing AT commands, 144
Tethered scanner, supported symbologies, 180
Text messages, Windows Mobile, 36
Time, setting, 255
Tips for working, Pocket Excel, 72
TLS
802.11 profile
certificates, 247
WPA encryption, 243
profile security information
WEP encryption, 242
WPA encryption, 243
Today, Windows Mobile settings, 38
Today screen, Windows Mobile, 26
Tools CD
CAB files, 87
management tools installed on desktop, 87
MIB files, 158
sample NPCP code, 166
Tracking people, via Contacts, 53
Transcriber, Windows Mobile input panel, 32
Troubleshooting
1551/1553 Tethered Scanners, 179
CAB Wizard, 201
does not turn off, 260
I/O key, 260
power status LED, 260
power supply, 260
shuts down during operation, 260
slow recovery after a boot, 260
unit does not turn on, 260
unit does not turn on in dock, 260
TTLS
802.11 radio module, WPA encryption, 245
profile security information, WEP encryption, 244
Typing mode, Pocket Word, 69
Typing on the screen, Pocket Word, 69
276
Unit, configuration parameters
automatic shutoff, 253
backlight timeout, 253
date/time, 253
key clicks, 253
volume, 253
Unit Manager, date/time, 253
Unshifted plane on keypad, regular keypad, 223
Update your PCS Vision profile, Phone application,
CDMA radios, 124
Updating, bootloader, 87
URLs
ActiveSync, 41
Adobe Acrobat Reader, 144
AT command interface
CDMA/1xRTT SB555, 144
GPRS/GSM MC45, 144
GPRS/GSM MC46, 144
GPRS/GSM MC75, 144
full screen display, 202
MIBs, 158
Microsoft Exchange e-mail account, 73
Microsoft Passport account, 73
Microsoft support, 26
MSDN library, 209
MSDN Windows CE documentation, 116
Windows Mobile, 26
Windows Mobile support, 26
Utilities applet
app launch, 234
dock switch, 232
registry save, 232
wakeup mask, 233
Verizon activation process, 135
Vibrator
enabling, 20
programming, 221
Video files, Windows Media Player, 76
Viewing mobile favorites and channels, Pocket Internet
Explorer, 82
Virtual wedge
bar code configuration
grid, 257
postamble, 258
preamble, 258
intermec settings, 182
Voice mail, Phone application, CDMA radios, 122
Volume
bar code configuration, 253, 255
configuration parameter, 253
VPN server, creating a connection, to work, 154
Wakeup mask, utilities applet, 233
700 Series Color Mobile Computer User’s Manual
Index
WAP pages, 79
connecting to an ISP, 148
Warm boot, performing, 16
Watcher applications
activating, Sprint, 137
downloading, Sprint, 137
using
Sprint, 139
Verizon, 135
Web browsers, FTP support, 208
Web pages, 79
connecting to an ISP, 148
WEP encryption
EAP-FAST security method, 249
LEAP security method, 247
PEAP security method, 240
profile security information, 238, 239
TLS security method, 242
TTLS security method, 244
zero configuration, 112, 113
WEP keys, hex values, 236
Wi-Fi Protected Access, 236
Windows CE documentation (MSDN), 116
Windows Media files, Windows Media Player, 77
Windows Media Player
Start menu icon, 28
Windows Mobile, 76
Windows Mobile
ActiveSync, 41
basic skills, 26
Calendar, 42
command bar, 28
Contacts, 53
getting connected, 103, 148
Inbox, 63
MSN Messenger, 73
navigation bar, 28
Notes, 62
notifications, 29
Pocket Excel, 71
Pocket Word, 68
pop-up menus, 28
programs, 27
700 Series Color Mobile Computer User’s Manual
status icons, 27
support URLs, 26
Tasks, 60
Today screen, 26
where to find information, 26
Windows Media Player, 76
writing on the screen, 32
Wired Equivalent Privacy, 236
Wireless network, 108, 236
creating a connection, 111
specifications, 22
Wireless printing, Bluetooth compatible module, 99
Wireless WAN
AT command interface
CDMA/1xRTT SB555, 144
GPRS/GSM MC45, 144
GPRS/GSM MC46, 144
GPRS/GSM MC75, 144
testing AT commands, 144
Work
creating
a modem connection, 152
a VPN server connection, 154
getting connected, 151
WPA, 236
WPA authentication
802.11 radio module, Zero Configuration, 114
with pre-shared key, Zero Configuration, 114
WPA encryption
802.11 radio module, 239
EAP-FAST security method, 250
LEAP security method, 248
PEAP security method, 240
TLS security method, 243
TTLS security method, 245
WPport, 101
Writing mode, Pocket Word, 70
Writing on the screen
See also Notes
Pocket Word, 70
Writing to drivers
DTR, 168
NPCP, 164
277
Index
Files Index
CABWIZ.DDF, 201
CABWIZ.EXE, 188, 201
COREDLL.DLL, 221
DEVICEID.H, 215
EXITME.BIN, 208
FTPDCE.EXE, 205, 208
AutoFTP, 210
FTP Server, 203
FTPDCE.TXT, 208
INTERMEC.MIB, 158
ITCADC.MIB, 158
ITCSNMP.MIB, 158
ITCTERMINAL.MIB, 158
MAKECAB.EXE, 201
NLED.H, 221, 222
NLEDGetDeviceInfo, 221
NLEDSetDevice, 222
NPCPPORT.DLL, 163
278
OEMIOCTL.H
IOCTL_GET_CPU_ID, 220
IOCTL_HAL_COLDBOOT, 217
IOCTL_HAL_GET_BOOT_DEVICE, 219
IOCTL_HAL_GET_BOOTLOADER_VERINFO,
216
IOCTL_HAL_GET_OAL_VERINFO, 216
IOCTL_HAL_GET_RESET_INFO, 218
IOCTL_HAL_ITC_READ_PARM, 211
IOCTL_HAL_ITC_WRITE_SYSPARM, 214
IOCTL_HAL_REBOOT, 219
IOCTL_HAL_WARMBOOT, 217
ONEIL.DLL, 167
PKFUNCS.H
IOCTL_HAL_GET_DEVICEID, 215
IOCTL_PROCESSOR_INFORMATION, 220
REBOOTME.BIN, 208
REGFLUSH.CAB, 89
__RESETMEPLEASE__.TXT, 198
RPM.EXE, 192
RPMCE212.INI, 192
SETUP.DLL, 191, 197
DllMain, 198
Sprint_Watcher_PPC_2002-03xxx.CAB, 138
TAHOMA.TTF, 192
WCESTART.INI, 192
700 Series Color Mobile Computer User’s Manual
Worldwide Headquarters
6001 36th Avenue West
Everett, Washington 98203
U.S.A.
tel 425.348.2600
fax 425.355.9551
www.intermec.com
700 Series Color Mobile Computer User's Manual
*961-054-031J*
P/N 961-054-031J

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-702
Modify Date                     : 2006:07:05 08:29:50-05:00
Create Date                     : 2006:07:05 08:29:41-05:00
Metadata Date                   : 2006:07:05 08:29:50-05:00
Creator Tool                    : PScript5.dll Version 5.2
Format                          : application/pdf
Title                           : legal
Creator                         : ThingA
Document ID                     : uuid:3930b95a-0205-45fc-bdff-6325da25962f
Instance ID                     : uuid:77c9f161-9fc0-4085-a44a-90943b9302be
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Page Count                      : 180
Author                          : ThingA

EXIF Metadata provided by EXIF.tools