Intermec Technologies RFID915PCC-6 RF IDENTIFICATION PC CARD User Manual 010416L1

Intermec Technologies Corporation RF IDENTIFICATION PC CARD 010416L1

Rev B App L PC Card Users Maunal

Intermec Technologies Corporation REPORT NO: 010416-1
EMC Test Laboratory DATE: April 16, 2001
DOC. NO.: 577-500-980 Page 1 of 2
915 PC Card Radio Module, FCC 15.247, Canada RSS-210, RSS-102 FCC ID: EHARFID915PCC-6
APPENDIX L, 915 PC Card-6 Users Manual and DoC insert, Rev B
Technologies Corporation
EMC Test Laboratory
Cedar Rapids, IA
MEASUREMENT/TECHNICAL REPORT
Intermec Technologies Corporation
RF Identification (RFID) 915 PC Card –6
915 MHz Spread Spectrum Transmitter
REPORT NO: 010416-1
DATE: April 16, 2001
APPENDIX L
DECLARATION OF CONFORMITY INSERT, USER INFORMATION
FOR THE 915 PC CARD
578-100-0xx Revision A Page 1 of 1
*578-100-0xx*
*578-100-0xx*
Compliance Statement Insert
Device Name: RF Identification Radio Module Model Number: 2450 PC Card -5
The responsible party for the compliance of this device is: Intermec Technologies Corporation
6001 36th Avenue West
Everett, WA 98203 USA
(425) 348-2600
This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripherals
approved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to this
product that are not approved by Intermec Technologies Corporation may void the compliance of this product and may result in
the loss of the users authority to operate the equipment.
FCC Digital Emissions Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the radio of television receiving antenna.
• Increase the separation between the computer equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.
• Consult the dealer or an experienced radio television technician for help.
Canadian Digital Apparatus Compliance
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
This device complies with part 15 of the FCC and Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
WARNING: RFID 915 PC Card
Warning: per the FCC and Canadian RF (radio frequency) exposure requirements,
1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to RF exposure
requirements. Intermec antenna part number(s) 805-589-001, 805-590-001 and 805-591-001. Correct antenna mounting is
fully described within the Intermec RFID 915 PC Card Users Guide.
2) When installing and using Intermec approved remote antennas associated the RFID reader, a 4-cm (1.5-inch) passing
distance must be maintained from any body part of the user or near by persons and the remote antenna. The antenna must
not be touched during transmitter operation.
3) Cables attached to the remote antennas must have a minimum length as provided from Intermec to insure the proper losses
to control RF exposure.
4) RF safety requirements mandate this device cannot be operated in close proximity to other transmitters.

Navigation menu