Intermec Technologies RFID915PCC-6 RF IDENTIFICATION PC CARD User Manual 030611G1

Download:
Mirror Download [FCC.gov]
Document ID	368804
Application ID	UcAOeHOuj1A5V0MDngzZnQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	1.7kB (21204 bits)
Date Submitted	2003-10-27 00:00:00
Date Available	2003-10-27 00:00:00
Creation Date	2003-10-14 16:36:14
Producing Software	Acrobat PDFWriter 4.0 for Windows
Document Lastmod	2003-10-17 16:17:51
Document Title	030611G1.PDF
Document Creator	Microsoft Word
Document Author:	Intermec User

Intermec Technologies Corporation
EMC Test Laboratory
DOC. NO.: 577-501-130
915 PC Card Radio Module, IP3, PCII, FCC 15.247, Canada RSS-210, RSS-102
APPENDIX G, User Manual
REPORT NO: 030611-1
DATE: June 11, 2003
Page 1 of 2
FCC ID: EHARFID915PCC-6
MEASUREMENT/TECHNICAL REPORT
Technologies Corporation
EMC Test Laboratory
Cedar Rapids, IA
Intermec Technologies Corporation
RF Identification (RFID) 915 PC Card –6
915 MHz Spread Spectrum Transmitter
REPORT NO: 030611-1
DATE: June 11, 2003
Appendix G
USER MANUAL
Page 2
Intermec IP3 Compliance Insert
Compliance Statement Insert
Device Name: RFID Scanner for Hand-held Computer
Model Number: IP3
The responsible party for the compliance of this device is:
Intermec Technologies Corporation
6001 36th Avenue West
Everett, WA 98203 USA
(425) 348-2600
This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripherals
approved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to this
product that are not approved by Intermec Technologies Corporation may void the compliance of this product and may result in
the loss of the users authority to operate the equipment.
FCC Digital Emissions Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the radio of television receiving antenna.
Increase the separation between the computer equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.
Consult the dealer or an experienced radio television technician for help.
Canadian Digital Apparatus Compliance
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
This device complies with part 15 of the FCC and Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: See users guide instructions for handling, charging, and replacing batteries. Failure to follow those instructions can
result in personal injury, fire, or battery explosion.
INTERMEC RFID Scanner IP3 Users
WARNING: per the FCC and Canada RSS-102, RF (radio frequency) exposure requirements,
(1) Only the antenna supplied and installed with this unit by Intermec Technologies is to be used with this scanner. The product
is configured to ensure compliance to RF exposure requirements.
(2) The user shall not touch the scanner front (antenna) during operation. Proper use of the scanner should direct the antenna
toward items to be scanned. A 20-cm (8-inch) passing distance must be maintained from any body part of the user or near by
persons and the scanner antenna.
(3) RF safety requirements mandate this device cannot be co-located with other transmitters.
578-100-0xx Revision C
*578-100-0xx*
*578-100-0xx*
Page 1 of 1

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Annotate, Fill forms, Extract, Assemble, Print high-res
Creator                         : Microsoft Word
Create Date                     : 2003:10:14 16:36:14
Title                           : 030611G1.PDF
Author                          : Intermec User
Producer                        : Acrobat PDFWriter 4.0 for Windows
Modify Date                     : 2003:10:17 16:17:51-05:00
Page Count                      : 2

EXIF Metadata provided by EXIF.tools