Invixium Access MPROX Biometric Fingerprint Reader User Manual

Invixium Access Inc. Biometric Fingerprint Reader

User Manual

IXM Installation GuideINVIXIUMACCESS
INVIXIUMCopyright© 2013invixiumaccessTable of ContentsGlossary and Denitions ..............................................................................................................................................................3Electrostatic Discharge and Earth Ground ......................................................................................................................................4Device Handling and Cleaning ......................................................................................................................................................5IXM INSTALL KIT Contents.........................................................................................................................................................6IXM MYCRO ...........................................................................................................................................................................7IXM SENSE .............................................................................................................................................................................9IXM TOUCH ........................................................................................................................................................................... 11I/O Cable: Top Connector Pin Out ............................................................................................................................................... 13I/O Cable: Bottom Connector Pin Out .......................................................................................................................................... 14Hardware Tools Required ........................................................................................................................................................... 15Hardware Installation Steps ....................................................................................................................................................... 16Connections for Power ............................................................................................................................................................... 20Connections for Communication ................................................................................................................................................. 22Connections for Operation ......................................................................................................................................................... 26Electrical Specications ............................................................................................................................................................. 28Software Installation System Requirements ................................................................................................................................. 29Software Installation Steps ........................................................................................................................................................ 30Notices ................................................................................................................................................................................... 32Support ................................................................................................................................................................................... 35
INVIXIUMCopyright© 2013invixiumaccessGlossaryACP Access Control PanelCOM CommonDAC Door Access ControlDOS Door Open ScheduleEGND Earth GroundESD Electrostatic DischargeGND GroundIXM INVIXIUMLED Light Emitting DiodeNC Normally ClosedNO Normally OpenOTG On-the-Go RLY RelayRX ReceiverSGND Signal GroundSPI Specic Purpose InputSPO Specic Purpose OutputTX TransmitterWDATA Wiegand DataWGND Wiegand GroundVIN+ Power (12-24 VDC)VIN- Power GroundDenitionsTemporary Back CoverWired Back CoverMetal Mounting Plate
INVIXIUMCopyright© 2013invixiumaccessElectrostatic Discharge and Earth GroundFor protection against Electro Static Discharge (ESD), which may cause damage or malfunction to the IXM device, Invixium recommends the use of the ground connections between each IXM device and a high quality Earth Ground available at the install site. Installation of any IXM device should be performed by licensed electricians and installers should always use an antistatic wrist strap during the set up process.An Earth Ground wire with lug is provided in the IXM INSTALL KIT. The lug of the Earth Ground wire should be fastened with a screw to the front of the mounting plate. The other end of the Earth Ground wire should be connected to the high quality Earth Ground connection on site. When the IXM device is installed onto the mounting plate, this Earth Ground lug will make direct contact with the Metal Back plate of the IXM device, thus allowing for proper grounding. Please refer to Hardware Install Steps on page 15 for step-by-step instructions for mounting plate, device and Earth Ground wire installation.
INVIXIUMCopyright© 2013invixiumaccessDevice Handling Do's• Handle with care, ensure not to drop or step on the device.• Perform regular cleaning to eliminate a build-up of dust, dirt, oil and residual grime.Device Handling Don'ts• Do not install in areas where devices are exposed to direct sunlight, high levels of humidity, extreme dust or ammable vapours.• Do not allow magnetics or magnetic objects to come in close contact to any device.• Do not install near any heating elements or equipment.• Do not let any liquids spill onto the device, specically the sensor.• Do not attempt to open or disassemble the device, as this will void the product warranty.• Do not deploy for any use other than its intended purpose.• Do not insert anything other than the correct tting USB plug into the USB port, located at the bottom of the device.Device CleaningThe component that will require regular cleaning is the sensor, as it experiences the most contact. The cleaning should be performed with care and attention, as improper cleaning may damage the sensor or surrounding components. Follow the steps below for proper sensor cleaning procedure:1. Power off device prior to any routine cleaning.2. Lightly moisten a new cotton swab or lint free polishing cloth with water or isopropyl alcohol.3. Gently wipe the surface of the sensor with the moistened cotton swab or cloth, ensuring that no excess liquid is squeezed out and runs into the device.4. Finish the wiping the sensor again with a dry cotton swab or cloth.5. Reapply power.WARNINGDo not use harsh or abrasive chemicals to clean the surface of the sensor, as this may cause permanent damage to the device.Do not use sandpaper, steel wool, scouring pads, chlorinated, ammonia, bleach, or any inappropriate products for cleaning.
INVIXIUMCopyright© 2013invixiumaccessThe IXM Install Kit includes:• Dolphin Crimps (qty 24)• Earth Ground Wire• Lithum Battery (IXM TOUCH only) • Metal Mounting Plate • Metal Mounting plate screw (qty 1)• Micro USB-on-the-Go cable• Micro USB Extension cable (4 ft/1.2m)• Wall Mount Screws (qty 6)• Wired Back Cover with colour-coded wires• USB KeyBattery (IXM TOUCH only)
LEDsSensorLEDsSensorCPU BoardFront ShellNAND FlashTemporaryBack CoverIP65 gasketIXM MYCRO Device & Exploded viewsMetal Back PLate
IXM MYCRO Product & Mounting Plate Actual Dimensions in mmINVIXIUM recommends printing this page in Actual Size16241.703082.111048168Front View38.546.3Side View Front View8.104.20Side ViewAngled Front View
Lumidigm SensorLEDsFront ShellProximity SensorCPU Board512MB DDR3L RAMIP65 gasketTemporaryBack CoverIXM SENSE Device & Exploded viewsLEDsLumidigm SensorWi-Fi BoardMetal Back PLate
IXM SENSE Product & Mounting Plate Actual Dimensions in mmNVIXIUM recommends printing this page in Actual Size199.7Front View46.0851.85Side View45.20194.9Front View95.40Side ViewAngled Front View493082.1110
IXM TOUCH Device & Exploded viewsLEDsCapacitive Touch Screen LCDCapacitive Touch Screen LCDSensorCorning® Gorilla® GlassFront ShellLEDsSensorCPU BoardWi-Fi BoardIP65 gasketTemporaryBack CoverMetal Back PLateBatteryProximity Sensor
IXM TOUCH Product & Mounting Plate Actual Dimensions in mmNVIXIUM recommends printing this page in Actual Size49199.7Front View46.0851.85Side View45.20194.9Front View95.40Side ViewAngled Front View82.111030
INVIXIUMCopyright© 2013invixiumaccessRLY_NCRLY_NORLY_COMACP_LED2ACP_LED_GNDACP_LED1DAC_IN1DAC_IN3DAC_IN2DAC_GNDNCDAC_OUTSPI_GNDSPI_2SPI_1SPI_3SPO_GNDSPO_2SPO_3SPO_1Application Label PinSpecic Purpose Output Line 1 SPO_1 2Specic Purpose Output Line 2 SPO_2 4Specic Purpose Output Line 3 SPO_3 6Ground for Specic Purpose Outputs SPO_GND 8Specic Purpose Input Line 1 SPI_1 10Specic Purpose Input Line 2 SPI_2 12Specic Purpose Input Line 3 SPI_3 14Ground for Specic Purpose Inputs SPI_GND 16Door Access Control Output DAC_OUT 18Reserved for Future (No Connect) N/C 20Wire ColorApplication Label PinRelay Normally Closed RLY_NC 1Relay Common RLY_COM 3Relay Normally Open RLY_NO 5Access Control Panel LED 1 Feedback ACP_LED1 7Access Control Panel LED 2 Feedback ACP_LED2 9Ground for Access Control Panel LED Feedback ACP_LED_GND 11Door Access Control Input 1 DAC_IN1 13Door Access Control Input 2 DAC_IN2 15Door Access Control Input 3 DAC_IN3 17Ground for Door Access Control Inputs DAC_GND 19Wire ColorI/O Cable: Top Connector Pin Out Front View Back ViewWired Back Cover
INVIXIUMCopyright© 2013invixiumaccessApplication Label PinRS-232 Data Receive RS-232_RX 2RS-232 Data Transmit RS-232_TX 4Signal Ground SGND 6RS-485 Non-Inverting Line RS-485+ (B) 8RS-485 Inverting Line RS-485- (A) 10Wiegand Data Input Line 0 WDATA_IN0 12Wiegand Data Input Line 1 WDATA_IN1 14Wiegand Data Output Line 0 WDATA_OUT0 16Wiegand Data Output Line 1 WDATA_OUT1 18Ground for Wiegand WGND 20Application Label PinPower (+12-24 VDC) VIN+ 1Power Ground VIN- 3Earth Ground EGND 5RS-485 Terminated (Optional)* RS-485_T 7Ethernet or PoE† TCP/IP 9,11,13, 15,17,19*This pin is optional and should be used in place of the RS-485+ terminal if 120Ω termination is required. †PoE only available for IXM SENSE and IXM TOUCHI/O Cable: Bottom Connector Pin Out Wire ColorWire ColorRJ45 ReceptacleWGNDWDATA_OUT0WDATA_IN0WDATA_OUT1WDATA_IN1RS-485+ (B)RS232_TXRS-485- (A)SGNDRS232_RXVIN+EGNDVIN-TCP/IPRS-485_TFront View Back ViewWired Back CoverNOTE
INVIXIUMCopyright© 2013invixiumaccessHardware Tools Required• Power Drill• Electric or Battery-powered Screw driver• Wire Stripper• Hammer• Ratchet style Crimping tool• Pencil for markingPencilWire StripperBattery powered ScrewdriverHammerPower DrillCrimping toolInstallation of any IXM device should be performed by licensed electricians. NOTE
INVIXIUMCopyright© 2013invixiumaccess1 Turn Off Power This protects the device being installed.ONOFF2 IXM Install Kit Remove the Metal Mounting Plate, Wired Back Cover and Screws.4 Drill Holes Drill holes where marked and install the appropriate wall anchors (not included).3 Mark the Screws Holes INVIXIUM recommends the use of the 4 circular holes for mounting. Refer to diagrams on page 8, 10 or 12 for actual dimensions. Ideal mounting height is 120 - 140 cm from the ground to the top of the device. But also be sure to align the device in case of multiple installations.120-140 cmsIXM INSTALL KIT
INVIXIUMCopyright© 2013invixiumaccess6 Insert ScrewsAlign the holes of the mounting plate with the wall anchors and attach the mounting plate with the screws provided in theIXM Install Kit. Invixium recommends the use of an electric or battery-powered screwdriver for this step.5 Get Wires Get access to the installation wires either from behind the wall or from the wiring conduit. Feed wires through the square hole of the mounting plate.7 Identify the Connections:DC PowerVIN+ VIN-EGND PoERJ-45ReceptacleEGNDPower & Grounding1Communications RS-485SGND RS-485+RS-485-EthernetRJ-45ReceptacleUSB RS-232 RS-232_RX RS-232_TX SGNDOperations ACPACP_LED1ACP_LED2ACP_LED_GNDWDATA_OUT0WDATA_OUT1WGNDDACRLY_COMRLY_NODAC_IN1DAC_IN2DAC_OUT23OROR OR ORORRefer to pages 20 & 21 for Power connections, pages 22-25 for Network or Serial Communication connections and pages 26 & 27 for Operation connections.
INVIXIUMCopyright© 2013invixiumaccessDOLPHINEarth Ground Wire8A Make the Connections Connect the required wires using the Dolphin® crimps provided in the IXM Install Kit and a ratchet style crimping tool. Insert the two wires (no stripping required) into the open end of the crimp and then using the crimping tool, clamp down on the middle of the Dolphin® crimp.8B Connect Earth Ground An Earth Ground wire with lug is also provided in the IXM INSTALL KIT. Connect the lug of the Earth Ground wire directly to the front of the mounting plate using one of the provided screws. Ensure that the lug is secured tightly as to make the necessary contact between the device and the mounting plate. Connect the other end of the Earth Ground wire to the Earth Ground connection of the install site using one of the Dolphin® crimps provided in the IXM INSTALL KIT. Ensure all required connections are made to each device in the setup prior to turning on the power.Checklist: Connections for Power & Grounds (DC or PoE) Connections for Communications (Ethernet, Wi-Fi, RS-485, RS-232 or USB) Connections for Operation (ACP or DAC)Lug
INVIXIUMCopyright© 2013invixiumaccess10 Secure the Device Finally, secure the device on the bottom to the mounting plate with the Metal Mounting Plate screw provided in the IXM Install Kit.9 Attach the Device Take the IXM device and unscrew the Temporary Back Cover, keeping the screws handy. Connect the Wired Back Cover to the back of the device by lining up the connectors. Secure the Wired Back Cover with the same screws. Next, hang the IXM device onto the mounting plate as shown in the series of diagrams below.12INVIXIUM3
INVIXIUMCopyright© 2013invixiumaccessConnections for PowerINVIXIUM recommends:• 12-24 VDC regulated power supply• Dedicated Power Supply for each IXM device (minimum 1 A)• Use of a battery back-up or UPS with built-in surge protection• If sharing power supplies, ensure that each device is supplied with minimum 1 A per device (ie. Powering two devices will require a supply with output current of 2 A)DC Power SupplyVIN+VIN-EGNDProduct Warranty is void if improper power (under or over) is supplied to the device.IXM TOUCHDC Power SupplyUPSEGNDVIN+VIN-WARNING
INVIXIUMCopyright© 2013invixiumaccessINVIXIUM recommends:• An IEEE 802.3af compliant Active Midspan Injector for demo prupose (sold separatly) • A centralized Power Sourcing Equipment (PSE) for full PoE deployments• Use of a battery back-up or UPS with built-in surge protectionOnly available on IXM SENSE and IXM TOUCHINVIXIUM recommended PoE Injector SpecsInput Voltage 90-264 VAC, 60 HzInput Current 0.4 A @ 100 VACOut Voltage 48 VDCOutput Current 0.32 APower 15.36 WattPoE InjectorRouterHost PCIXM TOUCHConnections for Power Over Ethernet (PoE)Both IEEE 802.3af power transmission modes (A and B) are supported.NOTE
INVIXIUMCopyright© 2013invixiumaccessEthernet and Wi-Fi CommunicationEthernet:• Hub/Router required• CAT 5 cabling or betterWiFi:• Wireless router to LAN/WAN• 802.11b/g/n protocol• WEP, WPA and WPA2 encryptions supported• DHCP enabled by defaultIXM WEBRouter connected to LAN/WANIXM TOUCHIXM SENSEIXM MYCRO
INVIXIUMCopyright© 2013invixiumaccessRS-485 Network CommunicationINVIXIUM recommends:• Daisy chain conguration • Maximum 31 devices in the network• Last device in the chain network should be terminated (not included, refer to NOTE below for correct Resistor values)• Connect the IXM device to PC via RS-485-to-Serial (RS-232 or USB) Converter• Maximum cable length of 1200 m (4000 ft.) at 9600 bps baud rateBottom Connector RS-485SGND (6)RS-485+ (8)RS-485- (10)RS-485 to USB ConverterIXM TOUCHIXM WEBIXM SENSEIXM MYCRORR = 120 ohms for Standard RS-485 CablingR = 100 ohms for CAT5/6 CablingNOTE
INVIXIUMCopyright© 2013invixiumaccessSerial CommunicationRS-232:• Connect IXM device directly to the DB9 Serial port of the PC (if available)• DB9 connectors and cables are not includedBottom Connector RS-232RS-232_RX (2)RS-232_TX (4)SGND (6)DB9 Serial PortIXM WEBIXM TOUCHRS232_RXRS232_TXSGND1 2 3 4 5
INVIXIUMCopyright© 2013invixiumaccessUSB:• Connect a Flash Drive via Micro USB OTG cable and perform functions like upgrading rmware, downloading transaction logs and conguration les • USB port can also be used to connect to a PC running IXM WEB via Micro USB cable• Driver installation is required and will automatically initiate once the device is connectedHost PCMicro USB cable(Provided in IXM Install Kit)IXM SENSEUSB Communication
INVIXIUMCopyright© 2013invixiumaccessAccess Control Panel ConnectionsACP:• LED and Wiegand connections available for ACP operation• INVIXIUM recommends the use of Wiegand Output Data 0, 1 and GND connectionTop Connector LEDACP_LED1 (2)ACP_LED2 (4)ACP_LED_GND (6)Bottom Connector WiegandWDATA_OUT0 (2)WDATA_OUT1 (4)WGND (6)33WDATA_OUT0WDATA_OUT1WGNDACP_LED1ACP_LED2ACP_LED_GNDIXM TOUCHACPACP_LED1ACP_LED_GNDWDATA_OUT1ACP_LED2WDATA_OUT0WGNDIXM TOUCHACP_LED signals can be used if available on the Access Control Panel. IXM devices support up to 2 wires + GND for LED status.NOTE
INVIXIUMCopyright© 2013invixiumaccess+-Door Access Control ConnectionsDAC:• INVIXIUM recommends a separate power supply for Door Strike (not included)• Snubber Diode required for Door Strike (not included)• Internal Relay rated upto max of 1 A @ 30 VDC, external relay required if Door Strike draws more than 1A• For motion detector instead of Request-to-Exit-button, connect the following signals: (1) DAC_OUT to the COM and (2) DAC_IN2 to the Relay NO of the motion detectorBottom Connector DACRLY_COMRLY_NODAC_IN1DAC_IN2DAC_OUTRLY_NODAC_IN1RLY_COMDAC_OUTDAC_OUTDAC_IN2Snubber DiodeDoor Strike Power Supply*Max Relay rating=1 Amp @ 30 VDCDoor StrikeDoor ContactRequest to exitSnubber DiodeDoor ContactRequest to exitDAC_IN2DAC_GNDDAC_OUTDAC_IN1ElectricstrikeRLY_NORLY_COM+-IXM TOUCH* Max Relay rating-1 Amp @ 30 VDCDoor Strike Power SupplyIXM TOUCH
INVIXIUMCopyright© 2013invixiumaccessElectrical Specications Min. Value Target Value Max. Value Recommendations Power Voltage (V) 9.6 12 24 Use regulated DC power Current (A) 0.7 1.2 SPI’s VIN_H (V) 4 - - VIN_L (V) - - 1 Pull-down Resistance (Ω) - 10K - Internal 10K Ω pull-down resistor is present on SPI-1, SPI-2 & SPI-3 lines Wiegand Inputs VIN_H (V) 2 - - VIN_L (V) - - 0.8 Pull-down Resistance (Ω) - 10K - Internal 10K Ω pull-up is present on Wiegand input lines SPO’s VOUT_H (V) 4.2 - - @IOH = -24mA VOUT_L (V) - - 0.44 @IOL = +24mA Wiegand Outputs VOUT_H (V) 4.5 - - VOUT_L (V) - - 0.8 Pull-up Resistance (Ω) - 4.7K - Wiegand Output is an open drain output. Internal 4.7K Ω pull-up is present on these lines Internal Relay Current Rating (A) - - 1 @ 30VDC 0.3 @125VAC Switching Power (Resistive) - - 30Watt DC 30VA AC Switching Voltage (V) - - 110 DC
INVIXIUMCopyright© 2013invixiumaccessPC Workstation• 1 GHz Intel® Pentium® 4 or equivalent (INVIXIUM recommends 2.0 GHz or higher)• 1 GB RAM (INVIXIUM recommends 2 GB RAM or higher)• Available COM or USB port• Ethernet Card (10/100 Mb Ethernet connections)• Monitor capable of displaying at least 1024 x 786 high colour resolutionOperating Systems• Windows® 8 and 7 both 32-Bit and 64-Bit versions• Windows® XP Service Pack 3 or higher• Windows® Server 2012• Windows® 2008 R2• Windows® 2008• Windows® 2003 R2IXM WEB™• 50 MB Free Hard disk spaceSoftware Installation System RequirementsTo successfully install and run Invixium software, the system must meet the following minimum requirements:Web Browsers (Client)• Internet Explorer® version 8.0 or higher• Google Chrome™ version 26.0 or higher• Mozilla Firefox® version 20.0 or higher• Apple Safari® version 5.1.7 or higherMicrosoft® .NET Framework• Version 4.0 Minimum 850 MB Hard Disk for x86 systems and 2 GB Hard Disk x64 • Version 2.0 (500 MB) – only required for Windows® XP & Windows® 2003 R2SQL Server™ 2008 Express Edition Service Pack 1• 1 GB Hard Disk (INVIXIUM recommends)Microsoft® Internet Information Services• Version 7.5 or higher Windows® Installer (Installs Automatically)• Version 4.5 or higher
INVIXIUMCopyright© 2013invixiumaccessIXM WEBVersion 1.1.6.0 INSTALL NEWS EXITAD VANCEDSoftware Installation StepsStep 1 Plug the USB drive (found in IXM INSTALL KIT) into an available port on PC.Step 2 Open the USB drive folder. Run IXMWEB.exe le. The IXM WEB Install Menu will initiate.Step 3 INVIXIUM recommends selecting INSTALL option for rapid installation (< 3 minutes). A Windows dialog may pop up to provide a warning about installing from an unreliable source. Click “Yes” to proceed with the install.NOTE
INVIXIUMCopyright© 2013Step 4 During the installation process, the status of the install will be shown.Step 5 When the installation is complete, click EXIT. IXM WEB icon is now on the desktop.Step 6 Run IXM WEB to launch the application in the default web browser.
INVIXIUMCopyright© 2013invixiumaccessFCC Information to Users (English)This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference2. This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna• Increase the separation between the equipment and receiver• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected• Consult the dealer or an experienced radio/TV technician for helpInformations de la FCC aux Utilisateurs (en Français)Cet appareil est conforme à la partie 15 des règles de la FCC. Son fonctionnement est soumis aux deux conditions suivantes:1. Cet appareil ne doit pas provoquer d'interférences nuisibles2. Cet appareil doit accepter toute interférence reçue, incluant toute interférence pouvant causer un fonctionnement indésirableNotice
INVIXIUMCopyright© 2013invixiumaccessCE Information to Users (English)All INVIXIUM devices have the CE mark for conformance with EMC Directive 89/336/EEC, and Low Voltage Safety Directive 73/23/EEC. Device with RFID components are compliant with R&TTE Directive 1999/5/EC, and are Class 1 Devices.Informations de la CE aux Utilisateurs (en Français)Tous les dispositifs de INVIXIUM ont le marquage CE de conformité à la directive CEM 89/336/CEE et basse tension de sécurité Directive73/23/CEE. Les appareils avec composants RFID sont conformes aux Directive R & TTE 1999/5/CE. et sont des appareils de classe 1.NoticationCet équipement a été testé et s'est avéré conforme aux limites pour un appareil numérique de Classe B, conformément à la partie 15 des règles de la FCC. Ces limites sont conçues pour fournir une protection raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet équipement génère, utilise et peut émettre des fréquences radio et, s'il n'est pas installé et utilisé conformément aux instructions, il peut causer des interférences nuisibles pour les communications radio. Cependant, il n'existe aucune garantie que des interférences ne se produiront pas dans une installation particulière. Si cet équipement provoque des interférences nuisibles à la réception radio ou de télévision, ce qui peut être déterminé en l'éteignant et rallumant, l'utilisateur est encouragé à essayer de corriger l'interférence par une ou plusieurs des mesures suivantes:• Réorienter ou déplacer l'antenne de reception• Augmentez la distance entre l'équipement et le récepteur• Connecter l'équipement à une sortie sur un circuit différent de celui sur lequel le récepteur est branché• Pour obtenir de l’aide, consulter le revendeur ou un technicien radio / TV expérimenté
INVIXIUMCopyright© 2013invixiumaccessIndustry Canada Information to Users (English)This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference2. This device must accept any interference, including interference that may cause undesired operation of the device Industrie Canada Information pour les Utilisateurs (en Français)Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Son fonctionnement est soumis aux deux conditions suivantes:1. Cet appareil ne doit pas provoquer d'interférences2. Cet appareil doit accepter toute interférence, y compris celles pouvant causer un mauvais fonctionnement de l'appareilWarning to Users (English)WarningChanges or modications not expressly approved by INVIXIUM could void the user's authority to operate the equipment.
invixium.comFor Technical or Customer Support issues, please contact your Local Authorized Reseller.For all other inquiries, please contact us atExperience@invixium.comFor more detailed information, please visit the links below:INSTALLATION GUIDEwww.invixium.com/installation INGUIDE (online copy)www.invixium.com/inguideUSER'S GUIDEwww.invixium.com/userguideinvixiumaccessEnjoy the Experience.Some features may vary based on device models.Copyright © 2013, INVIXIUM. All rights reserved.P/N XAD-051-01G© 2013 Google Inc. All rights reserved. ChromeTM browser is a trademark of Google Inc.Firefox logo® is a registered trademark of the Mozilla Foundation.Windows® and Internet Explorer® are trademarks of the Microsoft group of companies.Safari® is a trademark of Apple Inc.

Navigation menu