Iton Technology MW1601-5P Wi-Fi MODULE User Manual 15 MW1601 5P UserMan P2

Download:
Mirror Download [FCC.gov]
Document ID	2964949
Application ID	9igVLBT9z3FtUWeZZJZSjQ==
Document Description	15_MW1601-5P UserMan_P2.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	246.97kB (3087073 bits)
Date Submitted	2016-04-21 00:00:00
Date Available	2016-04-21 00:00:00
Creation Date	2015-11-11 17:58:20
Document Lastmod	2016-04-21 13:18:30
Document Title	15_MW1601-5P UserMan_P2.pdf

Our Focus , Your Legend
802.11 b/g/n single chip
Storage Temperature
-40℃~125℃
Antenna
external
Operation System
windows XP32/64,Vista 32/64, Win7 32/64, Linux, Mac
Operation Voltage
3.3V DC
6. Size Of Module Graph
6.1 Physical Map
Iton Technology Corp
www.sziton.com
802.11 b/g/n single chip
Our Focus , Your Legend
6.2 Machine Size Map And Pin Definition
Pin Definition
Pin
Name
Description
VCC
3.3V
DP
USB D+ signal
DM
USB D- signal
GND
Ground
NC
No connect
7.Process Parameters
TBD
Iton Technology Corp
www.sziton.com
802.11 b/g/n single chip
Our Focus , Your Legend
8.Packaging Information
Packing information :blister + vacuum bag
The module into the blister case
The blister packed
module and desiccant
into the vacuum bag
Blister (5*10)
A good vacuum sealed
vacuum bag in turn into
cartons
Vacuum bag
Cartons
10
Iton Technology Corp
www.sziton.com
9.Application
Installation Guide
Finished Assembly
Master PCB (examples)
1. Check MW1601‐5P Module
connection pin is clean for
soldering.
2. Ready the Master PCB
which will connect with
MW1601-5P Module. Check
connection pads is clean
forsoldering.Place
the
Module on the Master PCB
with SMT.
3. After soldering,Check
all
pads
are
well
connected.
4. Connect DC Power 3.3V
on VCC and GND on Master
PCB.Connect to Antenna by
antenna connector.
Antenna connector
NOTE:The antenna gain should no more than 0 dBi.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
Attention: Limited Modular Approval ‐ this RF Module may not be sold to the generic public
and requires professional installation.
Due to the fact that this RF Module is not equipped with an own shielding, the end‐product
incl. this RF Module has to show compliance to the FCC rules (15C / radiated emissions).
(OEM) Integrator has to assure compliance of the entire end‐product
incl. the integrated RF Module. Additional measurements (15C) and/or equipment authorizations
(e.g either a complete new certification or a Class II Permissive Change. )
may need to be addressed depending on co‐location or simultaenous
transmission issues if applicable.
Integrator is reminded to assure that these installation instructions
will not be made available to the end‐user of the final host device.
the Integrator will be responsible to satisfy SAR/ RF Exposure requirements,
when the module integrated into any (portable, mobile, fixed) host device.
The final host device, into which this RF Module is integrated" has to be labelled
with an auxilliary lable stating the FCC ID of the RF Module, such as
"Contains FCC ID: VYVMW1601-5P".
Depending on the size of the final end‐product, the §15.19 FCC statement
"This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation."
should be placed also on the device or alternatively within a prominent location of the users
manual
The §15.21 "Changes or modifications to this unit not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment." statement has to be included in a prominent
location of the users manual

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:30
Create Date                     : 2015:11:11 17:58:20Z
Modify Date                     : 2016:04:21 13:18:30+08:00
Metadata Date                   : 2016:04:21 13:18:30+08:00
Format                          : application/pdf
Document ID                     : uuid:ad78a198-68e0-4e31-89b8-7a23ca02cc2b
Instance ID                     : uuid:fd64a74c-60e2-6b40-aef9-48607cac07eb
Has XFA                         : No
Page Count                      : 7

EXIF Metadata provided by EXIF.tools