Itron 100GDLAS AMR transceiver device for utility meters User Manual 1

Itron Inc AMR transceiver device for utility meters Users Manual 1

Contents

Users Manual 1

    Natural Gas Solutions 100G DLS Gas ERT Module Installation Guide, Direct Mount  TDC-0823-009
 TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  ii   Proprietary and Confidential   Identification 100G DLS Gas ERT Module Installation Guide, Direct Mount  17 April 2012   TDC-0823-009 100G, 100G DL, 100G DLN, 100G DLS ERT module part numbers:  100G ERT: ERG-5000-001, ERG-5000-002, ERG-5000-003, ERG-5000-004, ERG-5000-005, ERG-5000-006, ERG-5000-007, ERG-5000-008 100G Datalogging ERT: ERG-5002-001, ERG-5002-002, ERG-5002-003, ERG-5002-004, ERG-5002-005, ERG-5002-006, ERG-5002-007, ERG-5002-008  100G Datalogging FN ERT: ERG-5003-001, ERG-5003-002, ERG-5003-003, ERG-5003-004, ERG-5003-005, ERG-5003-006, ERG-5003-007, ERG-5003-008, ERG-5003-009 100G DLS ERT: ERG-5006-001, ERG-5006-002, ERG-5006-003, ERG-5006-004, ERG-5006-005, ERG-5006-006, ERG-5006-007, ERG-5006-008, ERG-5006-009 Copyright ©  2010 - 2012 Itron, Inc. All rights reserved. Confidentiality Notice The information contained herein is proprietary and confidential and is provided subject to the condition that (i) it is held in confidence except to the extent required otherwise by law and (ii) it is used only for the purposes described herein. Any third party given access to this information is similarly bound in writing. Trademark Notice Itron is a registered trademark of Itron, Inc. All other product names and logos in this documentation are used for identification purposes only and may be trademarks or registered trademarks of their respective companies. Applicable Patents U.S. Patent Numbers: 4,614,945; 4,753,169; 4,768,903; 4,799,059; 4,867,700 Canadian Patent Numbers: 1,254,949; 1,267,936; 1,282,118 Compliance Statement This device complies with Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Operation is subject to the following two conditions:   This device may not cause harmful interference.   This device must accept any interference that may cause undesirable operation.  This device must be permanently mounted such that it retains a distance of 20 centimeters (7.9 inches) from all persons in order to comply with FCC RF exposure levels.  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.  If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:   Reorient or relocate the receiving antenna.   Increase the separation between the equipment and receiver.   Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.   Consult the dealer or an experienced radio or TV technician for help.    Compliance Statement   This equipment complies with policies RSS-210 and RSS-GEN of the Industry Canada rules.  Operation is subject to the following two conditions:   (1) this device may not cause interference, and  (2) this device must accept any interference, including interference that may cause undesired operation of the device.  Déclaration de conformité Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :   (1) l'appareil ne doit pas produire de brouillage, et   (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Transportation Classification The Federal Aviation Administration prohibits operating transmitters and receivers on all commercial aircraft. When powered, any 100G series gas ERT is considered an operating transmitter and receiver and cannot be shipped by air. All product returns must be shipped by ground transportation. Modifications and Repairs To ensure system performance, this device and antenna shall not be changed or modified without the expressed approval of Itron. Any unauthorized modification will void the user's authority to operate the equipment.  Meter Installation/Removal In the event of malfunction, all repairs should be performed by Itron. It is the responsibility of users requiring service to report the need for service to Itron.  Warning  Follow these procedures to avoid injury to yourself or others:    The lithium battery may cause a fire or chemical burn if it is not disposed of properly.   Do not recharge, disassemble, heat above 100º Celsius (212º Fahrenheit), crush, expose to water, or incinerate the lithium battery. Fire, explosion, and severe burn hazard.   Keep the lithium battery away from children.   Replace the lithium battery only with batteries meeting Itron specifications. Any other battery may cause a fire or explosion.  Warning  Only authorized Itron personnel should attempt repairs on Itron equipment. Attempts to do so by others might void any maintenance contract with your company. Unauthorized service personnel might also be subject to shock hazard on some Itron equipment if removal of protective covers is attempted.  Warning To prevent ignition of flammable or combustible atmospheres, disconnect power before servicing.  Warning  Substitution of components may impair intrinsic safety.
 TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  iii   Proprietary and Confidential     Suggestions If you have comments or suggestions on how we may improve this documentation, send them to TechnicalCommunicationsManager@itr on.com If you have questions or comments about the software or hardware product, contact Itron Technical Support: Contact  Internet: www.itron.com  E-mail: support@itron.com  Phone: 1 877 487 6602
 TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  iv   Proprietary and Confidential
 TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  v   Proprietary and Confidential     Before You Begin ........................................................................................................ vii Document Conventions ..................................................................................................................... vii Document Purpose ............................................................................................................................ vii Chapter 1  About the 100G DLS Gas ERT Module ...................................................... 1 Transmission Modes ........................................................................................................................... 1 100G DLS Gas ERT Module Security ................................................................................................. 2 Enabling 100G DLS Gas ERT Module Security ................................................................................. 2 100G Series Gas ERT Specifications ................................................................................................. 2 Related Documents ............................................................................................................................ 3 100G Series Gas ERT Meter Compatibility List .................................................................................. 3 Installation Prerequisites ................................................................................................................... 12 Installation Overview ......................................................................................................................... 13 Chapter 2  Elster American Meter Installation .......................................................... 14 Removing the Meter Index ................................................................................................................ 14 Assembling the ERT Module and Index ............................................................................................ 15 Programming the 100G DLS Gas ERT Module Assembly ............................................................... 18 Attaching the 100G DLS Gas ERT Module Assembly to the Meter .................................................. 19 Chapter 3  Sensus (Invensys, Equimeter, Rockwell) Meter Installation ................. 22 Removing the Meter Index ................................................................................................................ 22 Assembling the ERT Module and Index ............................................................................................ 23 Programming the 100G DLS Gas ERT Module Assembly ............................................................... 26 Attaching the 100G DLS gas ERT module Assembly to the Sensus Meter ..................................... 27 Chapter 4  Itron (Sprague) Meter Installation ............................................................ 29 Removing the Meter Index ................................................................................................................ 29 Assembling the ERT Module and Index ............................................................................................ 30 Programming the 100G DLS Gas ERT Module Assembly ............................................................... 32 Attaching the 100G DLS Gas ERT Module Assembly to the  Meter ................................................. 33 Attaching the 100G DLS Gas ERT Module Assembly to Flat-faced Sprague Meters ...................... 37 Securing Brass Meter Tags to Flat-faced Meters.............................................................................. 38 Attaching the 100G DLS Gas ERT Assembly on Sprague 175RM Meters ...................................... 40 Removing the Meter Index ................................................................................................................ 40 Assembling the ERT Module and Index ........................................................................................... 41 Programming the 100G DLS Gas ERT Module Assembly ............................................................... 44 Attaching the 100G DLS Gas ERT Module to the Sprague 175RM Meter ....................................... 45 Contents
Contents  TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  vi  Proprietary and Confidential    Chapter 5  National (Lancaster) Meter Installation ................................................... 48 Removing the Meter Index ................................................................................................................ 48 Assembling the ERT Module and Index ............................................................................................ 49 Programming the 100G DLS Gas ERT Module Assembly ............................................................... 53 Attaching the 100G DLS Gas ERT Module Assembly to the Meter .................................................. 54 Chapter 6  Elster American and Itron (Actaris) Commercial Meter Installation ..... 57 Removing the Index or Index Assembly from the Meter ................................................................... 57 Programming the 100G DLS Gas ERT Module ................................................................................ 60 Attaching the 100G DLS Gas ERT Module to the Commercial Meter .............................................. 61 Installing the Commercial 100G DLS Gas ERT Module on an Itron (Actaris) Commercial Meter .... 65 Programming the 100G DLS Commercial Gas ERT ......................................................................... 68 Attaching the 100G DLS Gas ERT Module to the Commercial Meter .............................................. 69 Chapter 7  Sensus (Rockwell) Commercial Meter Installation ................................. 74 Removing the Index or Index Assembly from the Meter ................................................................... 74 Programming the 100G DLS gas ERT module ................................................................................. 76 Attaching the 100G DLS Gas ERT Module to a Sensus/Rockwell Commercial Diaphram Meter .... 77 Mounting a 100G DLS Gas ERT Module on a Rockwell 750 meter with an Aluminum Box  Direct Reading (VDR) ........................................................................................................................ 80 Attaching the 100G DLS Gas ERT Module to a Sensus/Rockwell Commercial Diaphram Meter .... 81 Chapter 8  GE Oil & Gas Dresser Commercial Rotary Meter Installation ............... 84 Installation Prerequisites ................................................................................................................... 84 Installation Examples ........................................................................................................................ 85 Programming the 100G DLS Assembly ............................................................................................ 86 B3, LMMA, and S3A CTR/TC Dresser Series Register Settings and Direct Drive Programming Information......................................................................................................................................... 88 B3, LMMA and S3A CTR/TC Meter Drive Rates: Residential Direct Drive Programming* .............. 89 Installing the Residential 100G DLS ERT Module Assembly to the Dresser Rotary Meter .............. 90 Installing the Commercial Gas ERT on a Dresser Rotary Meter with an Instrument Drive .............. 91 Programming the 100G DLS Commercial Gas ERT Module Assembly ........................................... 92 B3, LMMA, and S3A CD/TD Dresser ROOTS® Series Meter Drive Rates ...................................... 94 Completed Installation Examples ..................................................................................................... 98 Index ............................................................................................................................. 99
Before You Begin   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  vii   Proprietary and Confidential     Document Conventions The following documentation conventions are used in this installation guide:  Caution   A Caution warns the installer that failure to follow the information in the note could result in loss of data. Be sure to carefully read a Caution note and follow the advice or instructions.  Warning  A Warning alerts the installer about potential physical harm to the installer or hardware. It is critical that you pay strict attention to Warning notes, read the information carefully, and follow the advice or instructions. Document Purpose This installation guide provides step-by-step instructions for installing the 100G series gas ERT module on a wide variety of meters. This installation guide may refer to the 100G series as the 100G DLS gas ERT module based on form or meter type. Mechanical installation procedures are identical for all modules. 100G series gas ERT module compatible meters are listed in the Meter Compatibility List.    Before You Begin  Tip  A Tip provides the installer with extra hints or suggestions to make a task easier to perform or a concept easier to understand.  Note  A Note supplies generic information to the installer. The installer can ignore the information and continue a task without suffering any adverse consequences.
Before You Begin   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  viii  Proprietary and Confidential
 TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  1   Proprietary and Confidential     Itron 100G DLS gas ERT modules are radio-frequency (RF) devices designed to transmit meter data to an RF meter reading device within transmission distance of the ERT module. The 100G gas ERT was designed with a higher output power than earlier Itron gas ERT modules to achieve an increased RF transmission distance. The 100G series gas ERT modules have greater output power to meet Itron mobile and fixed network requirements. The first 100G gas ERT module offered high transmit power capability which increased operational efficiency and reduced infrastructure costs. The 100G Datalogging gas ERT module was enhanced to offer higher transmit power with data logging capability (time-stamped hourly interval data) for both mobile and fixed network applications. Itron's 100G Datalogging Fixed Network (DLN) gas ERT module added improved network performance through a higher transmit power, accomplished using increased antenna efficiency and more robust optimized messaging structures. Itron's 100G DLS gas ERT module continues a legacy of increased efficiency in messaging and adds network security.  Transmission Modes The 100G DLS gas ERT module can be set to transmit in Fixed Network, Mobile and Handheld, or Hard to Read Mobile and Handheld Mode.   Fixed Network Mode.   The 100G DLS transmits a high-powered network interval message (NIM) RF message every five minutes. Output power in this mode is 500 milliwatts or +27 dBm. Interspersed in the high power NIM, the 100G DLS transmits a medium power RF message at 10 milliwatts or +10 dBm every 60 seconds; expected battery life is 20 years.   Mobile High Power Mode.  The 100G DLS transmits a high-powered RF message every 60 seconds. Output power in this mode is 250 milliwatts or +24dbm; expected battery life is 20 years.  Mobile and Handheld Mode.   The 100G DLS transmits a medium-powered RF message every 15 seconds. Output power in this mode is 10 milliwatts or +10dBm; expected battery life is 20 years.   (Optional) Hard to Read Mobile and Handheld Mode.   The 100G DLS transmits a high-powered RF message every 30 seconds. Output power in this mode is 250 milliwatts or +24dBm; expected battery life decreases to 15 years in this mode. The Hard to Read Mobile and Handheld Mode should only be used for exceptionally hard-to-read applications (such as meters installed on roof tops or in sub-basements).  An FCC license is not required to read 100G series gas ERT modules.   CH A P T E R   1  About the 100G DLS Gas ERT Module
About the 100G DLS Gas ERT Module   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  2  Proprietary and Confidential    100G DLS Gas ERT Module Security The 100G DLS is a component of a ChoiceConnect system. ChoiceConnect system security applies to the RF communications between the handheld computer, Mobile Collector, or Fixed Network system and the ERT module. There are two fundamental security processes used in the ChoiceConnect system to ensure confidentiality and validity of the system communications.  Authentication.  Authentication is the process of confirming that an artifact is genuine or valid. Authentication in the 100G DLS is the process of verifying a request is from a valid source and in its original form.  Encryption.  Encryption is the process of transforming information to make it unreadable to anyone who does not have a valid security key. There are two types of encryption, symmetric and asymmetric.  Symmetric encryption uses a shared key to decrypt or encrypt information. Asymmetric encryption uses a private key to encrypt and a public key to decrypt. As a component of the Itron ChoiceConnect solution, the 100G DLS supports the security model found in the  ChoiceConnect solution for both reading and programming. If the 100G DLS modules are shipped without ChoiceConnect security enabled, the utility can, at a later date, inject security key sets into the 100G DLS ERT modules.    Enabling 100G DLS Gas ERT Module Security When 100G DLS ERT modules ship from an Itron factory, each module contains a Utility Factory key.  The presence of this Utility Factory key does not enable security. The installer must enable security by injecting keys into the 100G DLS using an Itron programming device and programming commands. Initial key exchange commands are secured using the Utility Factory key. For more information, see the Field Deployment Manager Endpoint Tools Mobile Application Guide (TDC-0934) programming guide.  100G Series Gas ERT Specifications  Functional Specifications Description Power Source 100G 100G Datalogging 100G Datalogging FN 100G DLS  Two "A" cell lithium batteries One "A" cell lithium battery Tamper Detection Tilt tamper and magnetic tamper FCC Compliance Part 15 certified Industry Canada Compliance RSS-210 certified Intrinsically Safe per UL Class I, Division 1, Groups C and D Product Identification Numeric and bar coded ERT type and serial number Construction Materials Gray polycarbonate housing and back plate with encapsulated electronics
About the 100G DLS Gas ERT Module   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  3   Proprietary and Confidential      Operational Specifications Description Operating Temperatures -40° to 158° F (-40° to +70° C) Operating Humidity 5 to 95 percent relative humidity Program Frequency 908 MHz Transmit Frequency Spread spectrum 908 to 924 MHz ISM band Data Integrity Verified in every data message     Related Documents Document Title Document Part Number Gas Module Meter Compatibility List PUB-0117-002 Gas Module Ordering Guide PUB-0117-001 100G DLS Gas ERT Specification Sheet Publication 100941SP-XX 100G DLS Gas ERT Installation Guide, Remote Mount TDC-0824-XXX Field Deployment Manager Endpoint Tools Mobile Application Guide TDC-0934-XXX Field Deployment Manager Field Representative's Guide TDC-0936-XXX 100W and 100G ERT Tamper Reference Guide TDC-1028-XXX Note  The last three digits of the user and installation guides represent the document's revision level. The revision level is subject to change without notice.  100G Series Gas ERT Module Meter Compatibility List The following table lists meter types compatible with 100G series gas ERT modules. Due to continuous research and product improvements and enhancements, Itron reserves the right to change product or system specifications without notice.  Elster American (Canadian) Meter Model Meter Notes 100G Module Type Itron Part Number Gas Module Notes W75AL Aluminum case 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001  AC-175 Aluminum case  100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001  AL-175 Aluminum case 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001  ALC-175 Aluminum case 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001
About the 100G DLS Gas ERT Module   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  4  Proprietary and Confidential    Meter Model Meter Notes 100G Module Type Itron Part Number Gas Module Notes AT-175 Aluminum case 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001  AT-210 Aluminum case 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001  AL-225 Aluminum case, Canada only 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001  5B-225 Aluminum case 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001 Must cut 1/16" off the end of the module wriggler drive post which will make the module incompatible with other 2-ft. drive meters. 10 Metric B  Originally manufactured by Metric Metal Works 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001 ERT module with 2.5' cable AC-250 Aluminum case 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001  AL-250 Aluminum case 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001  AM-250 Aluminum case 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001  AR-250 Aluminum case 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001  AT-250 Aluminum case 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001  AL-350 Aluminum case 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001  AL-425 Aluminum case 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001  AC-630 Aluminum case 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001
About the 100G DLS Gas ERT Module   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  5   Proprietary and Confidential      Meter Model Meter Notes 100G Module Type Itron Part Number Gas Module Notes AL800 Top mount index 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-007 ERG-5002-007 ERG-5003-007 ERG-5006-007  AL1000 Top mount index 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001  AL1400 Top mount index 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-007 ERG-5002-007 ERG-5003-007 ERG-5006-007  AL2300 Top mount index 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-007 ERG-5002-007 ERG-5003-007 ERG-5006-007  AL3000 Top mount index 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-007 ERG-5002-007 ERG-5003-007 ERG-5006-007  AL5000  100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-007 ERG-5002-007 ERG-5003-007 ERG-5006-007  35B Iron case 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-007 ERG-5002-007 ERG-5003-007 ERG-5006-007  60B Iron case 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-007 ERG-5002-007 ERG-5003-007 ERG-5006-007  80B Iron case, must have front-reading index 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-007 ERG-5002-007 ERG-5003-007 ERG-5006-007  250B Iron case 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-007 ERG-5002-007 ERG-5003-007 ERG-5006-007  500B Iron case 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-007 ERG-5002-007 ERG-5003-007 ERG-5006-007  RPM Rotary CTR, TC (No pulser, no instrument drive) Use Elster American kit numbers 93179K002, 003, 004, or 005 to modify the meter with an adapter to attach the residential module. 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-003 ERG-5002-003 ERG-5003-003 ERG-5006-003
About the 100G DLS Gas ERT Module   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  6  Proprietary and Confidential    GE Oil & Gas/Dresser Meters (ROOTS) Meter Model Meter Notes 100G Module Type Itron Part Number Gas Module Notes Series B3  8C—56M CTR 8C—16M TC (No pulser,  No instrument drive)  To attach an Elster American AMR adapter kit, install Dresser AMR adapter kit, P/N 059599-000. 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001  Series A (LMMA) 1.5M—5M CTR (No pulser, No instrument drive)  To attach an Elster American AMR adapter kit, install Dresser AMR adapter kit, P/N 058530-610. 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001  Series A (LMMA) 7M—16M CTR (No pulser, No instrument drive) To attach an Elster American AMR adapter kit, install Dresser AMR adapter kit, P/N 058531-610. 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001  Series A (LMMA) 1.5M—5M TC (No pulser, No instrument drive)  To attach an Elster American AMR adapter kit, install Dresser AMR adapter kit, P/N 058224-610. 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001  Series Z 5C/8C15 To attach an Elster American Dresser AMR adapter kit, install Dresser AMR adapter kit, P/N 059224-847 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-001 ERG-5002-001 ERG-5003-001 ERG-5006-001  Instrument drive B3: CTR   TC, 8C—11M LMMA: CTR   TC: 1.5M—11M Instrument platform with mechanical drive. 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-007 ERG-5002-007 ERG-5003-007 ERG-5006-007 ERG-5000-008 ERG-5002-008 ERG-5003-008 ERG-5006-008  Itron (Actaris, Schlumberger, Sprague) Meter Model Meter Notes 100G Module Type Itron Part Number Gas Module Notes 175 2-hole index cover 3-hole index cover 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-005 ERG-5002-005 ERG-5003-005 ERG-5006-005  175 Combination 3-hole index cover  integrated regulator 2-hole index cover 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-005 ERG-5002-005 ERG-5003-005 ERG-5006-005  175RM Flat-face meter regulator on back of meter 100G Datalogging FN 100G DLS ERG-5003-009 ERG-5006-009  175WC 3-hole index cover 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-005 ERG-5002-005 ERG-5003-005 ERG-5006-006 Requires index boxes with 3 mounting holes
About the 100G DLS Gas ERT Module   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  7   Proprietary and Confidential      Meter Model Meter Notes 100G Module Type Itron Part Number Gas Module Notes 210  100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-005 ERG-5002-005 ERG-5003-005 ERG-5006-005  240  100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-005 ERG-5002-005 ERG-5003-005 ERG-5006-005  240 Flat-face meter 1-hole index cover 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-005 ERG-5002-005 ERG-5003-005 ERG-5006-005 Module requires Itron 1A Adapter Kit, P/N CFG-0015-001. 240  2-hole index cover 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-005 ERG-5002-005 ERG-5003-005 ERG-5006-005  240 Combination Integrated regulator 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-005 ERG-5002-005 ERG-5003-005 ERG-5006-005  250  100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-005 ERG-5002-005 ERG-5003-005 ERG-5006-005  250WC Integrated regulator 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-005 ERG-5002-005 ERG-5003-005 ERG-5006-005  METRIS 250 Slant-face 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-005 ERG-5002-005 ERG-5003-005 ERG-5006-005 A longer mounting screw may be required when retrofitting to some vintage METRIS meters. Longer mounting screw is Itron P/N 010626. 1A Flat-face meter includes 3-dial, 2 cf indexes. 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-005 ERG-5002-005 ERG-5003-005 ERG-5006-005 Installation requires Itron 1A Adapter Kit, P/N CFG-0015-001. 305 Combination Integrated regulator 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-005 ERG-5002-005 ERG-5003-005 ERG-5006-005  400 Slant-face meter 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-005 ERG-5002-005 ERG-5003-005 ERG-5006-005  400A Slant-face meter 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-005 ERG-5002-005 ERG-5003-005 ERG-5006-005
About the 100G DLS Gas ERT Module   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  8  Proprietary and Confidential     Meter Model Meter Notes 100G Module Type Itron Part Number Gas Module Notes 675A Top-mount index 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-007 ERG-5002-007 ERG-5003-007 ERG-5006-007 Requires Itron (Actaris) adapter P/N 8005901-001. Purchase from Itron. 800A Top-mount index 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-007 ERG-5002-007 ERG-5003-007 ERG-5006-007 Requires Itron (Actaris) adapter P/N 8005901-001. Purchase from Itron. 1000A Top-mount index 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-007 ERG-5002-007 ERG-5003-007 ERG-5006-007 Requires Itron (Actaris) adapter P/N 8005901-001. Purchase from Itron. National (Lancaster) Meter Model Meter Notes 100G Module Type Itron Part Number Gas Module Notes 175 National meter indexes with bow-tie shaped wrigglers cannot be used. 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-006 ERG-5002-006 ERG-5003-006 ERG-5006-006 Actaris/Schlumberger/Sprague direct read (odometer) indexes cannot be used. U175 UL175 National meter indexes with bow-tie shaped wrigglers cannot be used. 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-006 ERG-5002-006 ERG-5003-006 ERG-5006-006 Actaris/Schlumberger/Sprague direct read (odometer) indexes cannot be used. 250 National meter indexes with bow-tie shaped wrigglers cannot be used. 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-006 ERG-5002-006 ERG-5003-006 ERG-5006-006 Actaris/Schlumberger/Sprague direct read (odometer) indexes cannot be used. Romet  Meter Model Meter Notes 100G Module Type Itron Part Number Gas Module Notes Instrument drive RM series. Standard index drive and no instrument 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-007 ERG-5002-007 ERG-5003-007 ERG-5006-007  Sensus (Invensys/Equimeter/Rockwell/EMCO) Meter Model Meter Notes 100G Module Type Iron Part Number Gas Module Notes RT-100 18-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-004 ERG-5002-004 ERG-5003-004 ERG-5006-004 24- and 30-tooth gears are not compatible. S-110 11-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-002 ERG-5002-002 ERG-5003-002 ERG-5006-002  T-110 11-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-002 ERG-5002-002 ERG-5003-002 ERG-5006-002
About the 100G DLS Gas ERT Module   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  9   Proprietary and Confidential      Meter Model Meter Notes 100G Module Type Itron Part Number Gas Module Notes S-120 11-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-002 ERG-5002-002 ERG-5003-002 ERG-5006-002  T-120 11-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-002 ERG-5002-002 ERG-5003-002 ERG-5006-002  R-175 11-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-002 ERG-5002-002 ERG-5003-002 ERG-5006-002 24- and 30-tooth gears are not compatible. S-175 18-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-004 ERG-5002-004 ERG-5003-004 ERG-5006-004 24- and 30-tooth gears are not compatible. S-190 18-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-004 ERG-5002-004 ERG-5003-004 ERG-5006-004 24- and 30-tooth gears are not compatible. R-200 11-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-002 ERG-5002-002 ERG-5003-002 ERG-5006-002  RT-200 11-tooth 100G  100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-002 ERG-5002-002 ERG-5003-002 ERG-5006-002  S-200 11-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-002 ERG-5002-002 ERG-5003-002 ERG-5006-002  RC-225 11-tooth (Canadian only) 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-002 ERG-5002-002 ERG-5003-002 ERG-5006-002 24- and 30-tooth gears are not compatible. RT-225 11-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-002 ERG-5002-002 ERG-5003-002 ERG-5006-002 24- and 30-tooth gears are not compatible. RC-230 11-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-002 ERG-5002-002 ERG-5003-002 ERG-5006-002 24- and 30-tooth gears are not compatible. RCM-230 (RC-230 Metric) 16-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-003 ERG-5002-003 ERG-5003-003 ERG-5006-003 24- and 30-tooth gears are not compatible.
About the 100G DLS Gas ERT Module   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  10  Proprietary and Confidential     Meter Model Meter Notes 100G Module Type Itron Part Number Gas Module Notes RT-230 11-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-002 ERG-5002-002 ERG-5003-002 ERG-5006-002  250 11-tooth 100G 100G Datalogging  100G Datalogging FN 100G DLS ERG-5000-002 ERG-5002-002 ERG-5003-002 ERG-5006-002 24- and 30-tooth gears are not compatible. R-275 11-tooth 100G  100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-002 ERG-5002-002 ERG-5003-002 ERG-5006-002 24- and 30-tooth gears are not compatible. MR-8 (R-275 Metric) 16-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-003 ERG-5002-003 ERG-5003-003 ERG-5006-003 24- and 30-tooth gears are not compatible. RT-275 11-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-002 ERG-5002-002 ERG-5003-002 ERG-5006-002  S-275 11-tooth (side connections) 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-002 ERG-5002-002 ERG-5003-002 ERG-5006-002 24- and 30-tooth gears are not compatible. MR-5 (S-275 Metric) 16-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-003 ERG-5002-003 ERG-5003-003 ERG-5006-003 24- and 30-tooth gears are not compatible. 310 11-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-002 ERG-5002-002 ERG-5003-002 ERG-5006-002  R-315 11-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-002 ERG-5002-002 ERG-5003-002 ERG-5006-002 24- and 30-tooth gears are not compatible. MR-9 (R-315 Metric) 16-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-003 ERG-5002-003 ERG-5003-003 ERG-5006-003 24- and 30-tooth gears are not compatible. RT-360 18-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-004 ERG-5002-004 ERG-5003-004 ERG-5006-004  415 18-tooth. Older meters may have gas module to meter mounting hole variations that can make them incompatible. 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-004 ERG-5002-004 ERG-5003-004 ERG-5006-004  MR-12 (415 Metric) 16-tooth 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-003 ERG-5002-003 ERG-5003-003 ERG-5006-003 24- and 30-tooth gears are not compatible.
About the 100G DLS Gas ERT Module   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  11   Proprietary and Confidential     Meter Model Meter Notes 100G Module Type Itron Part Number Gas Module Notes 750 Vertical index only 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-008 ERG-5002-008 ERG-5003-008 ERG-5006-008  1000 Vertical index only 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-008 ERG-5002-008 ERG-5003-008 ERG-5006-008  1600 Vertical index only 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-008 ERG-5002-008 ERG-5003-008 ERG-5006-008  3000 Vertical index only 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-008 ERG-5002-008 ERG-5003-008 ERG-5006-008  5000 Vertical index only 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-008 ERG-5002-008 ERG-5003-008 ERG-5006-008  10000 Vertical index only 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-008 ERG-5002-008 ERG-5003-008 ERG-5006-008  750, 1000, 1600, 3000, 5000, 10000 Aluminum box direct reading (VDR) index 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-008 ERG-5002-008 ERG-5003-008 ERG-5006-008  EMCO #2-1/2 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-008 ERG-5002-008 ERG-5003-008 ERG-5006-008  EMCO #3 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-008 ERG-5002-008 ERG-5003-008 ERG-5006-008  EMCO #4 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-008 ERG-5002-008 ERG-5003-008 ERG-5006-008  EMCO #4-1/2 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-008 ERG-5002-008 ERG-5003-008 ERG-5006-008  EMCO #5 100G 100G Datalogging 100G Datalogging FN 100G DLS ERG-5000-008 ERG-5002-008 ERG-5003-008 ERG-5006-008
About the 100G DLS Gas ERT Module   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  12  Proprietary and Confidential    Installation Prerequisites Prior to installation, verify you have the following items:  100G gas ERT module designed for your specific brand of residential or commercial gas meters (ERTs include new tamper seals).  A compatible meter (see the 100G Series Gas ERT Module Meter Compatibility List).  A compatible index. Itron 100G DLS gas ERT modules are compatible with standard dial and direct-read (odometer) indexes. Exceptions are noted on the 100G Series Gas ERT Module Meter Compatibility List.  Installation tools (provided by installer or customer).  Small and medium flat-blade or Phillips screwdrivers.  Side-cutting plier/wire snips.  Small putty knife, residential meters.  Meter seals, wire seal, and seal press.  11/32-inch nut driver or other blunt tool.   Itron programming device: FC200SR handheld computer with Field Deployment Manager (FDM) software version 1.1 or higher or FC300 with SRead with Field Deployment Manager (FDM) software version 1.1 or higher or 900 MHz Belt Clip Radio with Endpoint-Link version 5.5 or higher or Field Deployment Manager (FDM) software version 1.1 or higher and a customer-supplied laptop   Replacement screws:     Replacement Screws Meter To mount the 100G DLS gas ERT module on the meter: Itron Part Number To mount the index on the 100G DLS gas ERT module housing: Itron Part Number Elster American  1/4 - 20 x 5/8" slotted, Fillister head  8 - 32 x 3/16" slotted, Fillister head  Sensus/Rockwell  10 - 24 x 5/8" slotted, Fillister head  6 - 32 x 5/8" slotted, Fillister head  Itron/Sprague   Sprague/Schlumberger 175 RM  10 - 24 x 5/8" slotted, Fillister head 10 - 24 x 1/2-inch, slotted Fillister head   SCR-0175-002 10 - 24 x 1/4" slotted, Fillister head  National/Lancaster  10 - 24 x 3/4" Phillips, flat-head, stainless steel  SCR-0014-004 10 - 24 x 3/8" thread-forming, Phillips pan-head to mount indexes with legs 6 - 19 x 3/8" thread-forming, Phillips, Fillister head to mount indexes with screw holes SCR-0017-001   SCR-0037-001
About the 100G DLS Gas ERT Module   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  13   Proprietary and Confidential     Replacement Screws Commercial Meter To mount the 100G DLS commercial ERT on the meter: Itron Part Number To mount the index (and index assembly, if applicable) on the 100G DLS commercial ERT housing: Itron Part Number Elster American 2A x 3.35" length, slotted round-head drilled to accept utility-approved wire seals SCR-0062-001   12 - 24 x 1/2" slotted, Fillister head machine screws, drilled to accept utility-approved wire seals  Sensus/Rockwell  2A x 3.63" length, slotted round-head drilled to accept utility-approved wire seals SCR-0062-002  2A x 2.94" length, slotted round-head SCR-0062-003 Sensus/Rockwell For Aluminum Box Direct Reading (VDR) index only      Installation Overview Installing the 100G DLS gas ERT module on a meter involves four tasks: 1. Removing the index cover and index from the meter. 2. Assembling the 100G DLS and index. 3. Programming the 100G DLS assembly. 4. Attaching the 100G DLS to the meter.
 TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  14   Proprietary and Confidential     This chapter provides the instructions to install the 100G DLS gas ERT module on an Elster American Meter.     Note  Properly dispose all unused screws, old index covers, gaskets, tamper seals, and other leftover materials. Do not leave materials on customer premises.  Removing the Meter Index Begin the ERT module installation by removing the index cover and index from the meter.  To remove the index from the meter 1. Remove the four index cover screws and the index cover from the Elster American meter. Alternate screw removal following the numbered pattern in the photo.   2. Examine the mounting screws. If they are 5/8-inch long and not corroded, keep them to re-attach the 100G DLS assembly. If the screws are not the correct length or if the screws are corroded, discard.  Note  You may use the removed index cover as a temporary storage container for screws. Properly dispose all unused screws, old index covers, gaskets, tamper seals, and other leftover materials. Do not leave materials on customer premises.  CH A P T E R   2  Elster American Meter Installation
Elster American Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  15   Proprietary and Confidential     3. Unscrew one index mounting screw completely. Hold one hand under the index to catch the screw. While removing the other mounting screw, pull the index away from the meter to keep the index backplate against the back of the screw. Remove the screw completely after the index is free of the meter.   Set the index aside where it will not be damaged or fill with dirt, rain or snow. The index will be mounted to the ERT later in this procedure.  4. Verify the index mounting screws are 3/16-inch long and not corroded. If the screws are the correct length and not corroded, retain for later use. If you discarded the original screws, use the correct replacement screws (see Installation Prerequisites.) 5. Remove the old gasket, gasket residue and dirt from the meter (if applicable). The meter face must be free of gasket residue before you install the 100G DLS gas ERT module.    Assembling the ERT Module and Index Continue ERT module installation by assembling the ERT module and index.  To assemble the 100G DLS gas ERT module and index 1. Separate the ERT module housing from the cover by pulling the cover straight out from the housing.
Elster American Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  16  Proprietary and Confidential    2. Set the ERT module clear cover aside where it will not be damaged or fill with rain, dirt, or snow. You will use the cover later in this installation procedure. Note  Elster American Meter indexes are available in different models: Index wrigglers on one-foot meters with drive slots   Index meters on two-foot meters with drive                                                                                           posts                                                 Index with mounting screw holes                                 Index with mounting slots                                                If your index has mounting screw slots, skip steps 3 and 4. If your index has mounting screw holes, perform steps 3 and 4, and skip steps 5 and 6. 3. Using the original index mounting screw or a replacement screw, if necessary, place one 8 - 32 3/16-inch screw into the index's right-hand mounting screw hole.    4. Attach the screw to the ERT housing's right-index mounting post just enough to hold the screw and the right end of the index in place.   5. Screw one 8 - 32 x 3/16-inch screw into the right index mounting post one or two turns. Do not tighten the screw.  6. Place the right index mounting screw slot under the screw head. Do not tighten the screw.
Elster American Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  17   Proprietary and Confidential     7. Slide the index drive post into the ERT wriggler. Verify positive engagement.  Caution  If the index wriggler has a drive slot, place the ERT wriggler's drive post into the index drive slot. Failure to mate the ERT module wriggler with the index drive post (or slot) can cause binding and lead to poor registration or meter failure. 8. Install and tighten the left index mounting screw (for indexes with either mounting screw slots or holes). Tighten the right index mounting screw. Install and tighten index mounting screws evenly.   9. Slide the ERT cover over the index and housing. Verify the cover is installed correctly. The ERT label should be clearly visible and easily read.
Elster American Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  18  Proprietary and Confidential    Programming the 100G DLS Gas ERT Module Assembly Program the 100G DLS using:  An FC200SR handheld computer with Field Deployment Manager (FDM) software version 1.1 or higher or  A FC300 with SRead handheld computer with Field Deployment Manager (FDM) software version 1.1 or higher or  A 900MHz Belt Clip Radio with Field Deployment Manager (FDM) software version 1.1 or higher and a customer-supplied laptop. The Belt Clip Radio connects to the user-supplied laptop using a USB cable or Bluetooth. See the Field Deployment Manager Endpoint Tools Mobile Application Guide (TDC-0934) for more complete programming information.       FC200SR               FC300 with SRead     900MHz Belt Clip Radio  Caution  You must program the 100G DLS gas ERT module before use.  The ERT is programmed based on the meter's drive rate. Take note of the index drive rate shown on a lower dial on the index. Elster American meter index drive rates are either 1-cubic foot, 2-cubic feet or 0.05 cubic meters (not shown below).
Elster American Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  19   Proprietary and Confidential     To program the 100G DLS gas ERT module  Program the meter drive rate into the 100G DLS gas ERT module using the endpoint programming device.   For all programming and Check Endpoint operations, hold the handheld programmer as close to vertical as possible. For best success, keep the handheld programmer within 6 feet of the target ERT.  Verify you have the correct programming mode (Fixed Network Mode, Mobile High Power Mode, Mobile/Handheld Mode, or Hard to Read Mobile/Handheld Mode) for your application.  Programming parameters are based on the configuration file loaded into the ERT module programming device. During programming, the 100G DLS gas ERT module is set to the nearest 100 cubic feet; the last two digits (tens and units) are programmed as zeros (0). After programming is complete, the ERT assembly will read to the nearest cubic foot.    Attaching the 100G DLS Gas ERT Module Assembly to the Meter After programming the 100G DLS gas ERT module, attach the ERT assembly to the Elster American Meter.  Warning  For 5B Meters only: If you are installing the 100G DLS on a 5B-225 aluminum meter, cut 1/16-inch off each ERT wriggler post to prevent the wriggler from rubbing on the face of the nut holding the meter drive dog in place. Trimming the drive post may make the module incompatible with other 2-ft. drive meters.    To attach the 100G DLS gas ERT module to the meter 1. Align the ERT wriggler to connect with the drive post (or slot) of the meter.        For one-foot meters: Align the ERT assembly wriggler perpendicular to the meter drive post.
Elster American Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  20  Proprietary and Confidential     For two-foot meters: Align the ERT assembly wriggler perpendicular to the meter drive slot. The pin on the ERT wriggler may be installed inside or outside the meter drive slot. For easy assembly, Itron recommends installing the pin on the 100G DLS wriggler outside the meter drive slot.  Warning  Failure to correctly align the meter drive post and ERT module drive slot can cause binding and lead to poor registration or meter failure. If there is a gap between the ERT module gasket and the meter, it may be the drive slot of the ERT module assembly's wriggler is not correctly aligned with the meter drive slot. Remove the 100G DLS assembly and repeat the alignment procedure. You must engage ERT module wriggler in the meter drive dog.  2. Carefully align the ERT's four screw holes with the holes on the meter. Attach using the original mounting screws if they are the correct size and are not corroded (1/4 - 20 x 5/8-inch screws.) If you discarded the original screws, use the correct replacement screws (see Installation Prerequisites). Tighten in an alternating, diagonal pattern as shown in the photo:    Insert first screw and tighten 1/4 to 1/2 turn after the screw contacts the meter connection.  Insert the second screw and tighten 1/4 to 1/2 turn after contact with the meter connection.  Insert the third screw and tighten 1/4 to 1/2 turn after contact with the meter connection.  Insert the last screw and tighten 1/4 to 1/2 turn after contact with the meter connection.  Return to the first screw and tighten. Continue with the second, third and last screw until all screws are tight. Use equal screw tension to tighten each screw.   Important  Meter manufacturers: torque the mounting screws 15 to 20 inch-pounds. 3. Place new tamper seals over the two screws with tamper seal mounts. Press tamper seals into place using an 11/32-inch nut driver or similar blunt tool.
Elster American Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  21   Proprietary and Confidential     4. Complete necessary paperwork and verify all excess materials are removed from the customer premises. 100G DLS gas ERT module installation on the Elster American meter is complete.
 TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  22   Proprietary and Confidential     This chapter provides the instructions to install the 100G DLS Gas ERT Module on a Sensus/Rockwell Meter. These instructions apply to 11-tooth, 16-tooth, and 18-tooth Sensus 100G DLSs.   Note Sensus meters are also known as Invensys, Equimeter, and Rockwell. For these instructions, all meter types are referred to as Sensus meters.       100G DLS gas ERT module  Sensus 11-tooth  Sensus 16-tooth  Sensus 18-tooth Removing the Meter Index Begin the ERT module installation by removing the index cover and index from the meter.  To remove the index from the meter 1. Remove the four index cover screws and the index cover from the Sensus meter. Alternate screw removal following the numbered pattern as shown in the following illustration.  2. Examine the mounting screws. If they are 5/8-inch long and not corroded, keep them to attach the 100G DLS gas ERT module assembly. If the screws are not the correct length or if the screws are corroded, discard.  Note  You may use the removed index cover as a temporary storage container for screws. Properly dispose all unused screws, old index covers, gaskets, tamper seals, and other leftover materials. Do not leave materials on the customer premises.  CH A P T E R   3  Sensus (Invensys, Equimeter, Rockwell) Meter Installation
Sensus (Invensys, Equimeter, Rockwell) Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  23   Proprietary and Confidential     3. Remove one index mounting screw completely. Hold one hand under the index to catch the screw. While removing the other mounting screw, pull the index away from the meter to keep the index backplate against the back of the screw. Remove the screw completely after the index is free of the meter.   4. Set the index aside where it will not be damaged or fill with dirt, rain, or snow. You will mount the index in the ERT later in this procedure. Verify the index mounting screws are 5/8-inch long and not corroded. If the screws are the correct length and not corroded, retain for later use. If you discard the original screws, use the correct replacement screws (see Installation Prerequisites on page 12.) 5. Remove the old gasket, gasket residue, and dirt from the meter (if applicable). The meter face must be free of gasket residue or dirt before you install the 100G DLS.     Assembling the ERT Module and Index Continue ERT module installation by assembling the ERT module and index.  To assemble the 100G DLS gas ERT module and index 1. Separate the ERT module housing from the clear cover by pulling the cover straight out from the housing. Set the ERT cover aside where it will not be damaged or fill with rain, dirt, or snow. You will replace the cover later in this installation procedure.
Sensus (Invensys, Equimeter, Rockwell) Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  24  Proprietary and Confidential    2. Place the index drive gear (1) in the housing wriggler gear cup (2) of the ERT. The example shows an 11-tooth drive gear. Your index may be a 16- or 18-tooth gear. Use the appropriate 100G DLS gas ERT module for your specific meter. See the Meter Compatibility List on page 3 for more information.  3. After the drive gear is aligned with the wriggler gear, the mounting holes will line up.  Warning  Indexes have varying drive mechanism styles. Failure to align the ERT wriggler with the index drive post can cause binding and lead to poor registration or meter failure. To verify proper engagement of the index to the ERT housing, spin the wriggler one clockwise rotation, then one-counterclockwise rotation. Do not spin the wriggler more than one complete rotation. The wriggler should spin freely, with little or no resistance.  4. Using the original index mounting screw or a replacement screw (if necessary), place one 6 - 32 x 5/8-inch screw into the index right mounting screw hole.   5. Attach the screw to the ERT housing right-index mounting post just enough to hold the screw and the right end of the index in place.  6. Install and tighten the left index mounting screw.
Sensus (Invensys, Equimeter, Rockwell) Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  25   Proprietary and Confidential     7. Tighten the right index mounting screw completely. Install and tighten both index mounting screws evenly.  8. Slide the ERT cover over the index and housing. Verify the cover is installed correctly. The ERT label should be clearly visible and easily read.
Sensus (Invensys, Equimeter, Rockwell) Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  26  Proprietary and Confidential    Programming the 100G DLS Gas ERT Module Assembly Program the 100G DLS using:  An FC200SR handheld computer with Field Deployment Manager (FDM) software version 1.1 or higher or  A FC300 with SRead handheld computer with Field Deployment Manager (FDM) software version 1.1 or higher or  A 900MHz Belt Clip Radio with Field Deployment Manager (FDM) software version 1.1 or higher and a customer-supplied laptop. The Belt Clip Radio connects to the user-supplied laptop using a USB cable or Bluetooth. See the Field Deployment Manager Endpoint Tools Mobile Application Guide (TDC-0934) for more complete programming information.       FC200SR               FC300 with SRead     900MHz Belt Clip Radio  Caution  You must program the 100G DLS gas ERT module before use.  The ERT is programmed based on the meter's drive rate. Take note of the index drive rate shown on a lower dial on the index. Elster American meter index drive rates are either 1-cubic foot, 2-cubic feet or 0.05 cubic meters (not shown below).
Sensus (Invensys, Equimeter, Rockwell) Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  27   Proprietary and Confidential     To program the 100G DLS gas ERT module  Program the meter drive rate into the 100G DLS gas ERT module using the endpoint programming device.   For all programming and Check Endpoint operations, hold the handheld programmer as close to vertical as possible. For best success, keep the handheld programmer within 6 feet of the target ERT.   Verify you have the correct programming mode (Fixed Network Mode, Mobile High Power Mode, Mobile/Handheld Mode, or Hard to Read Mobile/Handheld Mode) for your application.  Programming parameters are based on the configuration file loaded into the ERT module programming device. During programming, the 100G DLS gas ERT module is set to the nearest 100 cubic feet; the last two digits (tens and units) are programmed as zeros (0). After programming is complete, the ERT assembly will read to the nearest cubic foot.   Attaching the 100G DLS gas ERT module Assembly to the Sensus Meter After 100G DLS gas ERT module programming is complete, attach the ERT assembly to the Sensus meter.  To attach the 100G DLS gas ERT module to the meter 1. Place the ERT assembly against the front of the meter at angle.  Warning  Failure to correctly align the meter drive post and ERT module drive slot can cause binding and lead to poor registration or meter failure. If there is a gap between the ERT module gasket and the meter, it may be the drive slot of the ERT module assembly's wriggler is not correctly aligned with the meter drive slot. Remove the 100G DLS assembly and repeat the alignment procedure. You must engage ERT module wriggler in the meter drive dog.   2. Install and tighten the ERT-to-meter mounting screws in an alternating pattern. Use the original mounting screws if they were the correct size and not corroded. If you discarded the original screws, use the correct replacement screws (see Installation Prerequisites on page 12).  Align the top right mounting screw hole on the meter with the top right screw hole on the ERT.   Insert the top right cover mounting screw and tighten the screw enough to hold the ERT assembly in place. Do not completely tighten the screw.   Rotate the ERT assembly counterclockwise until the remaining three ERT screw holes line up with the holes in the meter.
Sensus (Invensys, Equimeter, Rockwell) Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  28  Proprietary and Confidential    3. Install the remaining three mounting screws and tighten in the pattern shown in the following illustration. Tighten each mounting screw evenly.  a. Insert lower left mounting screw (2) and tighten to snug position. b. Tighten upper right mounting screw (1,3) to snug position. c. Insert upper left mounting screw (4) and tighten to snug position. d. Insert lower right mounting screw (5) and tighten to snug position. Important  Meter manufacturers: torque the mounting screws 15 to 20 inch-pounds.  4. Place a new tamper seal over the two screws with tamper seal cups. Press the new tamper seals into place using an 11/32-inch nut driver (or similar blunt tool).    5. Complete any necessary paperwork and properly dispose excess installation materials and scrap from the customer premises. 100G DLS installation on the Sensus meter is complete.
 TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  29   Proprietary and Confidential     This chapter provides the instructions to install the 100G DLS Gas ERT Module on an Itron (Sprague) meter.   Note  Itron (Sprague) meters are also known as Actaris and Schlumberger meters. For these instructions, all meters will be referred to as Itron or Sprague meters.  Removing the Meter Index Begin the ERT module installation by removing the index cover and index from the meter.  To remove the index from the meter 1. Remove the index cover screws and the index cover from the Itron (Sprague) meter. Examine the mounting screws. If they are 5/8-inch long and not corroded, keep them to re-attach the 100G DLS assembly. If the screws are not the correct length or if the screws are corroded, discard.   Note  Use the removed index cover as a temporary storage container for the screws. Properly dispose all unused screws, old index covers, gaskets, tamper seals, and other leftover materials. Do not leave materials on customer premises. CH A P T E R   4  Itron (Sprague) Meter Installation
Itron (Sprague) Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  30  Proprietary and Confidential    2. Loosen the index mounting screws 1/2 to one turn. Slide the index to the left and off the mounting screws. Remove the index from the meter.     3. Set the index aside where it will not be damaged or fill with dirt, rain, or snow. You will mount the index in the ERT later in this procedure.  4. Verify the index mounting screws are 1/4-inch long and not corroded. If the screws are the correct length and not corroded, retain for later use. If you discard the original screws, use the correct replacement screws (see Installation Prerequisites on page 12). 5. Remove the old gasket, gasket residue, and dirt from the meter (if applicable). The meter face must be free of gasket residue or dirt before you install the 100G DLS.    Assembling the ERT Module and Index Continue ERT module installation by assembling the ERT module and index.  To assemble the 100G DLS gas ERT module and index 1. Separate the 100G DLS housing from the cover by pulling the cover straight out from the housing. Set the ERT cover aside where it will not be damaged or fill with rain, dirt or snow. You will use the cover later in this installation procedure.
Itron (Sprague) Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  31   Proprietary and Confidential     2. Insert the 10 - 24 x 1/4-inch screws into the index mounting posts two turns. Do not tighten the screws.     3. Align the index wriggler (1) with the ERT drive post (2). Carefully slide the index onto the mounting screws.         4. Verify the 100G DLS housing drive post makes positive engagement with the index wriggler.  Warning  Indexes have varying drive mechanism styles. Failure to align the ERT wriggler with the index drive post can cause binding and lead to poor registration or meter failure. To verify proper engagement of the index to the ERT housing, spin the wriggler one clockwise rotation, then one-counterclockwise rotation. Do not spin the wriggler more than one complete rotation. The wriggler should spin freely, with little or no resistance.  5. Hold the index in place and tighten the index mounting screws.   Warning  Verify the index is correctly positioned all the way to the right on the index mounting screws before you tighten the index mounting screws. Failure to properly mount the index on the index mounting screws may cause binding and meter failure. 6. Install and tighten the mounting screws evenly.
Itron (Sprague) Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  32  Proprietary and Confidential    7. Slide the ERT cover over the index and housing. Verify the cover is installed correctly. The ERT label should be clearly visible and easily read.  Programming the 100G DLS Gas ERT Module Assembly Program the 100G DLSs using:  An FC200SR handheld computer with Field Deployment Manager (FDM) software version 1.1 or higher or  A FC300 with SRead handheld computer with Field Deployment Manager (FDM) software version 1.1 or higher or  A 900MHz Belt Clip Radio with Field Deployment Manager (FDM) software version 1.1 or higher and a customer-supplied laptop. The Belt Clip Radio connects to the user-supplied laptop using a USB cable or Bluetooth. See the Field Deployment Manager Endpoint Tools Mobile Application Guide (TDC-0934) for more complete programming information.       FC200SR               FC300 with SRead     900MHz Belt Clip Radio  Caution  You must program the 100G DLS gas ERT module before use.
Itron (Sprague) Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  33   Proprietary and Confidential     The ERT is programmed based on the meter's drive rate. Take note of the index drive rate shown on a lower dial on the index. Elster American meter index drive rates are either 1-cubic foot, 2-cubic feet or 0.05 cubic meters (not shown below).        To program the 100G DLS gas ERT module  Program the meter drive rate into the 100G DLS gas ERT module using the endpoint programming device.   For all programming and Check Endpoint operations, hold the handheld programmer as close to vertical as possible. For best success, keep the handheld programmer within 6 feet of the target ERT.   Verify you have the correct programming mode (Fixed Network Mode, Mobile High Power Mode, Mobile/Handheld Mode, or Hard to Read Mobile/Handheld Mode) for your application.  Programming parameters are based on the configuration file loaded into the ERT module programming device. During programming, the 100G DLS gas ERT module is set to the nearest 100 cubic feet; the last two digits (tens and units) are programmed as zeros (0). After programming is complete, the ERT assembly will read to the nearest cubic foot.   Attaching the 100G DLS Gas ERT Module Assembly to the Meter After you program the 100G DLS gas ERT module, attach it to the Itron meter.
Itron (Sprague) Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  34  Proprietary and Confidential    To attach the 100G DLS gas ERT module to the meter 1. Align the ERT so one of its four drive fins (1) lines up with the meter drive dog (2).          Warning  Failure to correctly align the meter drive post and ERT module wriggler's fin can cause binding and lead to poor registration or meter failure. If there is a gap between the ERT module gasket and the meter, it may be the wriggler fin of the ERT module is dead headed against the meter drive dog.   Remove the 100G DLS assembly and repeat the alignment procedure. You must engage the meter drive dog in the ERT module wriggler fin.  2. Place the 100G DLS on the meter.  3. Insert the right module mounting screw and tighten the screw until the gasket is against the meter. Do not completely tighten the mounting screw.  Note  Use the original mounting screws to mount the 100G DLS if they were the correct size and not corroded. If you discarded the original screws, use the correct replacement screws (see Installation Prerequisites on page 12.)
Itron (Sprague) Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  35   Proprietary and Confidential     4. Slightly lift the left side of the ERT (the module will rotate on the right screw) until the left ERT mounting hole is approximately 1/4-inch above the left meter mounting hole.   5. Rotate the ERT down until the ERT mounting hole is approximately 1/4-inch below the meter hole.  6. Rotate the ERT up to align the left mounting holes.   7. Insert the left mounting screw and tighten a few turns.  8. Tighten the right and left ERT to meter mounting screws in an alternating pattern.   Important  Meter manufacturers: torque the mounting screws 15 to 20 inch-pounds.
Itron (Sprague) Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  36  Proprietary and Confidential    9. Place a new tamper seal in the tamper seal cups surrounding the two mounting screws.  Press the new tamper seals into place using an 11/32-inch nut driver or similar blunt tool.   10. Complete any necessary paperwork and properly dispose excess installation materials and scrap from the customer premises. 100G DLS gas ERT module installation on the Itron meter is complete.
Itron (Sprague) Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  37   Proprietary and Confidential     Attaching the 100G DLS Gas ERT Module Assembly to Flat-faced Sprague Meters 100G DLS gas ERT module installation on a flat-faced Sprague meter requires the Itron Adapter Plate Kit (CFG-0015-001).   Itron Adapter Plate Kit (CFG-0015-001) 1 Adapter Shim Plate 2 Index Cover Mounting Screws 3 Drive Dog 4 Adapter Plate Mounting Screws  To attach the 100G DLS gas ERT module assembly to Flat-faced Sprague meters 1. Verify the kit includes the materials listed in the Itron Adapter Plate Kit table.  Warning  The adapter plate must fit flush against the meter face. Some older Sprague meters are not compatible with the adapter plate. The following examples illustrate the potential obstruction (problem) areas between the adapter plate and meter. Failure to mount the adapter plate flush on the front of a meter could result in a binding condition and lead to poor registration or meter failure.
Itron (Sprague) Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  38  Proprietary and Confidential    2. Remove the drive dog from the flat-faced Sprague meter. Replace it with the extended drive dog included in the kit. Hand-tighten to snug. Warning   The meter drive dog shaft is surrounded by a gasket. A gas leak could result if the gasket is damaged. Do not use a tool to install or tighten the new drive dog. Hand-tighten only. 3. Attach the adapter plate to the meter with the gasket against the meter face. Secure with the two adapter plate mounting screws in an alternating fashion. Tighten each adapter plate screw evenly.  Insert the right adapter plate screw and tighten the screw enough to hold it in place.   Install the left mounting screw and tighten to a snug fit.   Finish by tightening the right mounting screw to a snug fit.  Note  The 100G DLS must be assembled, programmed, and attached to the meter following the instructions in  Assembling the 100G DLS Gas ERT Module and Index on page 30, Programming the 100G DLS Gas ERT Module Assembly on page 18, and  Attaching the 100G DLS Gas ERT Module to the Meter on page 33. Use the module mounting screws shipped with the Sprague 1A Adapter Plate Kit to mount the 100G DLS.   Securing Brass Meter Tags to Flat-faced Meters Some older Sprague meters have metal index covers with brass meter tags attached (by screws or rivets) to metal index covers.   Typically, brass meter tags have mounting (screw/rivet) holes on each end of the tag.  Mount brass meter tags using one of three Itron-approved methods.
Itron (Sprague) Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  39   Proprietary and Confidential     To secure brass meter tags to flat-faced meters Method 1 and 2  1. Carefully remove the brass meter tag from the meter index cover. Try not to damage the meter tag mounting holes.  2. Attach the 100G DLS assembly to the meter. The Sprague adapter plate has tag mounting holes in the lower left and right corners. Secure the meter tag to one of the holes with a utility-approved and provided security seal.    Method 1: Attach the meter tag to the adapter plate tag mounting hole  Method 2: Attach the meter tag to the 100G DLS gas ERT module mounting hole Note  If the brass meter tag will be secured to the meter utilizing the ERT-to-meter mounting hole, it must be attached during the 100G DLS installation procedure described in Step 1 of Attaching the 100G DLS Gas ERT Module to the Meter on page 33. Caution  A protruding brass meter tag can present a safety concern particularly if the tag is damaged with sharp edges protruding from the meter. Method 3 1. Remove the 100G DLS gas ERT module index cover.
Itron (Sprague) Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  40  Proprietary and Confidential    2. Place the meter tag inside the ERT assembly for optimal meter tag security. (See To assemble the 100G DLS gas ERT module and index on page 30.)  Method 3: Place the brass meter tag inside the 100G DLS assembly  Attaching the 100G DLS gas ERT module Assembly on Sprague 175RM Meters This section provides the information to install the 100G DLS on a Sprague 175RM meter.   Removing the Meter Index Begin the ERT module installation by removing the index cover and index from the meter.
Itron (Sprague) Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  41   Proprietary and Confidential     To remove the index from the meter 1. Remove the index cover mounting screws and the index cover from the Sprague 175RM meter. Discard the index cover and index cover mounting screws.     Note The removed index cover may be used as a temporary refuse container for screws. Properly dispose the index cover and all unused screws, gaskets, tamper seals, and other leftover materials. Do not leave materials on customer premises.  2. Loosen the index mounting screws 1/2 to one turn. Slide the index up and off the mounting screws and remove it from the meter.  Set the index aside where it will not be damaged or fill with dirt, rain or snow. You will mount the index in the module later in this procedure. Remove the index mounting screws from the meter. Verify the index mounting screws are 1/4-inch long and not corroded. If the screws are the correct length and not corroded, retain for later use. If the original screws are discarded, use the correct replacement screws (see Installation Prerequisites on page 12). 3. Remove the old gasket, gasket residue, and dirt from the meter (if applicable). The meter face must be free of gasket residue or dirt before you install the 100G DLS.    Assembling the ERT Module and Index Continue ERT module installation by assembling the ERT module and index.
Itron (Sprague) Meter Installation   TDC-0823-009 100G DLS Gas ERT Module Installation Guide, Direct Mount  42  Proprietary and Confidential    To assemble the 100G DLS gas ERT module and index 1. Separate the 100G DLS housing from the cover by pulling the cover straight out from the housing. Set the module cover aside where it will not be damaged or fill with rain, dirt or snow. The cover is used later in this installation procedure.  2. Screw the index mounting screws into the index mounting posts loosely (one to two turns). Do not tighten the screws.    3. Align the index wriggler (1) with the ERT module drive post (2).

Navigation menu