Itron 100WA AMR transceiver device for utility meters User Manual

Itron Inc AMR transceiver device for utility meters Users Manual 1

a href="https://usermanual.wiki/Itron" itemprop="url"> Itron >

Users Manual 2

 TDC-0909-001 100W and 100WP Pit Datalogging Water Endpoint Installation Guide  10   Proprietary and Confidential     Install the endpoint using one of the following methods: 100W and 100WP  Mounting Options Rod mount The endpoint mounts on a 1/2 inch outside diameter rod. Wall mount The endpoint mounts to a wall or other vertical surface. Base mount The endpoint mounts on a horizontal, flat surface. Shelf mount The endpoint mounts in pre-fabricated pockets or shelves within the pit lid using a shelf mount accessory kit. Through lid The endpoint mounts in lids with hole sizes from 1 3/4 inches to 2 inches. Through lid installation requires the Pit Lid Mounting Kit (CFG-1300-004). For water pit boxes, the type of installation method is based on two factors: the lid material and the current lid configuration. Metal lids may require a through-lid remote mount antenna for optimal endpoint radio performance. Plastic lids and other composite materials accept any installation methods described above. The 100W Endpoint is temperature rated from -20º C to +60º C. Do not install the 100W Endpoint in locations that may exceed the temperature rating.  Caution  Observe the following guidelines for mounting the 100W:   Endpoint positioning other than upright could negatively affect radio performance and battery life.   Use only Itron-approved splice kits or inline connectors.    100W and 100WP Endpoint Accessories 100W/100WP  Mounting Accessories Accessory Part Number Remote Antenna Kit (Mobile Applications Only) CFG-0900-001 Shelf Mount Kit  CFG-1300-001 Pit Lid Mounting Kit CFG-1300-004  100W and 100WP Endpoints with Integral Connectors If 100W Endpoints with integral connectors (ERW-1300-X0X) and the registers are not installed at the same time, secure the protective connector cover on the endpoint using a cable tie (Itron part number MSE-0005-002). Cable ties are not shipped with the 100W Endpoint, but can be ordered from Itron. Use the protective cover (on the endpoint side) in the field for up to one year.  Warning  If a dual-port 100W Endpoint is installed but the Leak Sensor is not attached,  the environmental cap (MSC-0019-005) must remain in place on the blue connector (Leak Sensor connector) to protect the connector from damage.  CH A P T E R   4  Installing the 100W and 100WP Endpoint
Download:
Mirror Download [FCC.gov]
Document ID1380870
Application IDPhsRlyntkJ031V93NJp70Q==
Document DescriptionUsers Manual 2
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize219.72kB (2746457 bits)
Date Submitted2010-11-24 00:00:00
Date Available2010-11-24 00:00:00
Creation Date2010-11-23 08:40:08
Producing SoftwareMicrosoft® Office Word 2007
Document Lastmod2010-11-23 08:47:04
Document Title100W and 100WP Pit Datalogging Water Endpoint Installation Guide
Document CreatorMicrosoft® Office Word 2007
Document Author: TDC-0909-001

Users Manual .2

Download:
Mirror Download [FCC.gov]
Document ID1436047
Application IDxtg4lUGm1gPGQIlMloh7tQ==
Document DescriptionUsers Manual .2
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize111.16kB (1389522 bits)
Date Submitted2011-03-23 00:00:00
Date Available2011-03-23 00:00:00
Creation Date2011-03-08 09:07:27
Producing SoftwareMicrosoft® Office Word 2007
Document Lastmod2011-03-08 09:07:40
Document Title100W and 100WP Pit Datalogging Water Endpoint Installation Guide
Document CreatorMicrosoft® Office Word 2007
Document Author: TDC-0909-002
FCC ID Filing: EWQ100WA

Navigation menu