Itron ORRN Routing node (Gateway) for part of an Automatic Meter Reading network User Manual ERT Gateway Installation Guide

Itron, Inc. Routing node (Gateway) for part of an Automatic Meter Reading network ERT Gateway Installation Guide

UserManual.wiki >

ORRN User Manual

Users Manual

OpenWay® Riva Routing NodeERT Gateway Installation GuideTechnicalCommunicationsknowledge to shape your future

IdentiﬁcationOpenWay® Riva Routing Node-ERT Gateway Installation Guide14 December 2017TDC-1744-000Copyright© 2017 Itron, Inc. All rights reserved.Conﬁdentiality NoticeThe information contained herein is proprietary and confidential and is being providedsubject to the condition that (i) it be held in confidence except to the extent requiredotherwise by law and (ii) it will be used only for the purposes described herein. Any thirdparty that is given access to this information shall be similarly bound in writing.Trademark NoticeItron is a registered trademark of Itron, Inc.All other product names and logos in this documentation are used for identification purposesonly and may be trademarks or registered trademarks of their respective companies.SuggestionsFor more information about Itron or Itron products, see www.itron.com.If you have questions or comments about the software or hardware product, contact ItronTechnical Support Services.Contact• Email: support@itron.com• Internet: support.itron.com• Telephone Itron Technical Support North America: 1-877-487-6602For technical support contact information by region, go to www.itron.com and select yourcountry and language.

ContentsChapter 1 Important Safety and Compliance Information.............................. 1USA, FCC Part compliance.................................................................................................................................. 1Electromagnetic compatibility...............................................................................................................................2Chapter 2 Getting Started: OpenWay® Riva Routing Node-ERT Gateway.... 3ERT Gateway related documents......................................................................................................................... 3Installation location information............................................................................................................................ 4ERT Gateway components................................................................................................................................... 4ERT Gateway housing................................................................................................................................5ERT Gateway antennas..............................................................................................................................6Chapter 3 Planning an ERT Gateway Installation.............................................7Installation proles................................................................................................................................................ 7Siting the ERT Gateway........................................................................................................................................ 7Propagation study for the ERT Gateway installation site ..........................................................................8AC power requirements............................................................................................................................. 8AC mains power....................................................................................................................................................8Mounting hardware requirements......................................................................................................................... 9Chapter 4 Installing the ERT Gateway.............................................................10Installation overview............................................................................................................................................10Mounting the ERT Gateway antennas................................................................................................................ 10Attaching the standard 915MHz ERT antenna.........................................................................................10Attaching the backhaul antenna.............................................................................................................. 12Mounting the ERT Gateway................................................................................................................................ 13Mounting hardware.................................................................................................................................. 13Mounting the ERT Gateway on a pipe..................................................................................................... 15Mounting the ERT Gateway on a pole..................................................................................................... 16Mounting the ERT Gateway on a davit arm............................................................................................. 16Connecting the ground wire.....................................................................................................................17Connecting the ERT Gateway power.......................................................................................................17Connecting the power cable.............................................................................................................18ERT Gateway wiring diagram...................................................................................................................18Chapter 5 OpenWay Riva Routing Node Communications Software...........20Appendix A ERT Gateway Speciﬁcations........................................................21Dimensions and weight.......................................................................................................................................21Antenna specications........................................................................................................................................21Environmental specications.............................................................................................................................. 22Transmitter.......................................................................................................................................................... 22ERT Gateway power operating range.................................................................................................................22ERT Gateway Installation Guide TDC-1744-000 iiiProprietary and Confidential

Chapter 1 Important Safety and ComplianceInformationThis section provides important information for your safety and product compliance.USA, FCC Part complianceThis device complies with Part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation.Operation is subject to the following two conditions:• This device may not cause harmful interference.• This device must accept any interference that may cause undesirable operation.This device must be installed to provide a separation distance of at least 20 centimeters (7.9inches) from all persons to be compliant with regulatory RF exposure.USA, FCC Class B-Part 15This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. Thisequipment generates, uses, and can radiate radio frequency energy and, if not installed andused in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiveris connected.• Consult the dealer or an experienced radio or TV technician for help.Modifications and RepairsTo ensure system performance, this device and antenna shall not be changed or modifiedwithout the express approval of Itron. Per FCC rules, unapproved modifications or operationbeyond or in conflict with these instructions for use could void the user's authority to operatethe equipment.ERT Gateway Installation Guide TDC-1744-000 1Proprietary and Confidential

Electromagnetic compatibilityCaution: Use only approved accessories with this equipment. All cables must behigh quality, shielded, and correctly terminated. Unapproved modifications oroperation beyond or in conflict with these use instructions may void the authority'sauthorization to operate the equipment.Important Safety and Compliance InformationERT Gateway Installation Guide TDC-1744-000 2Proprietary and Confidential

Chapter 2 Getting Started: OpenWay® RivaRouting Node-ERT GatewayThe OpenWay Riva Routing Node-ERT Gateway provides a unified means of reading Itron100G series and 100W series devices over an IPv6 network. The OpenWay Riva RoutingNode ERT Gateway can be deployed in one of two network configurations designated in thefirmware. The ERT Gateway Star operates over a Star network to collect the Itron 100Series gas and water ERT module reads.Note: The ERT Gateway does not support 100W+ Series modules operating in ExtendedRange Mode (Geo Mode).The ERT Gateway Mesh (future release) will operate over a Mesh network.The network configuration is selected on the specification form at the time the system isordered.The ERT Gateway communicates directly with the Connected Grid Router (CGR). Thegateway utilizes RF links with optimized modulation rates. The CGR then transmits the datato the OpenWay Operations Center (a part of the head-end system) over the utility'sbackhaul communication solution. The ERT Gateway's flexible design provides installationoptions for a variety of wall-mounted or pole-mounted locations. This flexibility providesoptimal communication effectiveness and range and minimizes installation costs.Important: Installation must be completed by professional installers to ensure trouble-freeoperation of the Itron OpenWay system. Follow these product installation instructions toensure proper operation of your OpenWay Riva Routing Node ERT Gateway Star.Use the ERT Gateway shipping packaging to transport the ERT Gateway. The shippingmaterials protect the ERT Gateway from damage.ERT Gateway related documentsThe listed documents provide additional information for ordering and working with theOpenWay Riva Routing Node ERT Gateway Star.Document Itron part numberOpenWay Riva Routing Node-ERT Gateway Ordering Guide PUB-1306-001OpenWay Collection Manager Installation and Configuration Guide TDC-1675-XXXERT Gateway Installation Guide TDC-1744-000 3Proprietary and Confidential

Document Itron part numberOpenWay® Operations Center Performance Manager Integration GuideIntegration GuideTDC-1718-XXXInstallation location informationThe ERT Gateway is designed for the listed installation locations:• Wood, concrete, or metal utility pole• Wall (indoor or outdoor)• Pipe or mast (between 2 and 3.5" in diameter)• RoofNote: Roof installation requires a 3rd-party, non-penetrating mounting kit (for example,Tessco #461587)• Other vertical structuresIntegrated mounting and coupling brackets secure the device in high winds and underheavy ice loads. Consult a professional engineer with concerns about your ERT Gatewaymounting location.The ERT Gateway consists of several components in a single, weatherproof device.Electrical components are encased in a plastic enclosure that provides optimum safety forthe installer.Warning: In accordance with FCC rules, unapproved modifications or operationbeyond or in conflict with these use instructions could void the user's authority tooperate the equipment. Only authorized Itron personnel may open the ERTGateway. Unauthorized access or modifications to the ERT Gateway will void thewarranty.ERT Gateway componentsThe ERT Gateway (Star) has two antennas that are mounted directly on the gatewayhousing.• Backhaul antenna• ERT antennaSince the ERT Gateway can be installed in outdoor environments, each component of thegateway is weather-tight and able to withstand wind speeds in excess of 100 miles per hour.Note: Review the ERT Gateway Ordering Guide (PUB-1306-001) for specific part numbersand component options to determine the ERT Gateway configuration.Getting Started: OpenWay® Riva Routing Node-ERT GatewayERT Gateway Installation Guide TDC-1744-000 4Proprietary and Confidential

ERT Gateway housingThe ERT Gateway housing contains the electronic components and radio boards. The radioantennas are included with the gateway and are directly mounted to the housing.Caution: Only authorized Itron personnel may open this device. Unauthorizedaccess or modifications to this product voids the warranty. Per FCC rules,unapproved modifications or operation beyond or in conflict with the installationinstructions in this guide could void the user's authority to operate the equipment.Designator Component Description1 ERT Gateway The ERT Gateway processes data received through the antennas and relays it to theOpenWay Operations Center (OWOC). Only authorized Itron personnel may open thisproduct housing.2 ERT antenna A 915MHz antenna that receives messages from the 100 series ERT modules in thenetwork. The connection for this antenna is type N female.3 ERT GatewaylabelThe label displays the identification number, model number, and other associatedgateway information.4 PowerconnectorThe power connector supplies power to the ERT Gateway. A three-pin cable connectsthe ERT Gateway to the AC mains power supply.5 BackhaulantennaA 915MHz antenna that provides a connection to the STAR or MESH network. Theconnection for this antenna is a type N female.6 Ground lug The ground lug is optional on the ERT Gateway and is provided for utilities that require aseparate earth ground.Note: When the ERT Gateway is powered with the light pole/photo sensor adapter, thereis no ground connection. Use the ground lug in this configuration.7 LED Statusindicator The status indicator displays the current operational status of the ERT Gateway.The LED indicator is located on the bottom of the housing.• Unpowered (off)• Initializing (green blink)• Running (green)• Error (yellow)The LED is configurable for the following display modes:• None (no light)• Error only• NormalGetting Started: OpenWay® Riva Routing Node-ERT GatewayERT Gateway Installation Guide TDC-1744-000 5Proprietary and Confidential

ERT Gateway antennasThe ERT Gateway utilizes two antennas.•ERT antenna The ERT antenna is a standard, higher gain, vertically polarized antennathat mounts directly to the top of the ERT Gateway housing.•Backhaul antenna The backhaul antenna is a standard, lower gain, vertically polarizedantenna that mounts directly to the bottom of the ERT Gateway housing.Caution: This equipment has been designed and approved per FCC rules tooperate with the antennas listed. The required antenna impedance is 50 ohms. Toreduce potential radio interference to other users, the antenna type and its gain werechosen so that the equivalent isotropically radiated power (EIRP) is not more thanthat permitted for successful communication. Antennas not included in this list andapproved by Itron are strictly prohibited for use with this device. Installing theOpenWay Riva Routing Node ERT Gateway with an unapproved antenna will voidthe product warranty and can void the user's authority to operate this equipment.Getting Started: OpenWay® Riva Routing Node-ERT GatewayERT Gateway Installation Guide TDC-1744-000 6Proprietary and Confidential

Chapter 3 Planning an ERT Gateway InstallationThis chapter describes ERT Gateway installation preparation and planning.Installation proﬁlesThe ERT Gateway may be installed in a variety of configurations and locations (for moreinformation, see Installation location information on page 4). Itron identified the followingprofiles for ERT Gateway installations.Location Location descriptionUtility pole The ERT Gateway is installed on a utility pole. Mount the ERT Gateway at amaximum height of 25 feet high on the utility pole for optimum reception.Light pole/street lightThe ERT Gateway is installed on either a light pole or the davit arm of the streetlight. Mount the ERT Gateway at a maximum height of 25 feet high on the lightpole/street light for optimum reception.Pipe or mast The ERT Gateway is secured/installed to a pipe or fence railing (from 2 to 3.5inches in diameter). Mount the ERT Gateway at a maximum height of 25 feet highon the pipe or fence for optimum reception.Siting the ERT GatewayERT Gateways can be installed in the field on a variety of surfaces. The listed surfaces areexamples of surfaces that support the ERT Gateway.• Wooden or metal walls• Metal pipes• Fence railings• Utility polesIn determining the ERT Gateway placement, observe the following primary considerationsas placement best practices.• For optimum RF reception.• In a location where there is a power connection.• On a structure on in a location that can physically support the weight of the ERT Gateway(and its mounting hardware).Caution: Always get permission to install the ERT Gateway at the selected site priorto installation. If you have questions or need help, contact Itron Support.ERT Gateway Installation Guide TDC-1744-000 7Proprietary and Confidential

Propagation study for the ERT Gateway installation sitePrior to the ERT Gateway field installation, contact Itron. Itron performs these tasks duringthe propagation study to determine the exact ERT Gateway installation location and the bestmounting surface.• Evaluate the quantity and types of network endpoints.• Assess the environmental and geographical considerations for the ERT Gatewayinstallation.• Optimize the ERT Gateway placement within the network to get the best possiblereception.• Assess the physical and structural implications of the selected mounting surface.This iterative process may be repeated as the final installation parameters are determined.AC power requirementsThe ERT Gateway requires an 102-264 VAC source defined as a minimum 15-amp branchcircuit (or larger). The ERT Gateway must be protected by a certified branch circuit breaker.Warning: Do not connect the ERT Gateway to a circuit protected by a GFCI breaker.The wiring must be sized in accordance with the National Electrical Code, ANSI/NFPA 70and, where applicable, the Canadian Electrical Code, Part I, CSA C22.1 or the prevailinglocal code.AC mains powerThe AC mains wiring to the ERT Gateway utilizes a three-conductor cable. Terminate thecable with either a NEMA L5-15 (125V, 15A), NEMA L6-15 (250V, 15A) locking plug, or bydirectly splicing to the secondary power to meet electrical codes.The ERT Gateway must be powered by an 102-264 VAC source defined as a maximum 15-amp branch circuit.Warning: Verify the 102-264 VAC power source (15-amp branch circuit). Do notconnect the ERT Gateway to the wrong voltage during installation. Supplying thewrong voltage could result in a fire hazard!The ERT Gateway must be protected by a certified branch circuit breaker. Do not connectthe ERT Gateway to a circuit protected by a GFCI breaker. Size the wiring in accordancewith the National Electrical Code, ANSI/NFPA 70, and where applicable, the CanadianElectrical Code, Part 1 CSA C22.1 or the prevailing local code. Power wiring on the Itron-supplied power cable follows conventional color coding for AC wiring: green (ground), white(neutral), and black (hot).Planning an ERT Gateway InstallationERT Gateway Installation Guide TDC-1744-000 8Proprietary and Confidential

3. Thread the antenna onto the top of the ERT Gateway. Do not over-tighten.Caution: Do not cross-thread the connection.4. Push the rubber boot as close as possible to the top of the ERT Gateway.5. Slide the antenna collar over the antenna with the font of the antenna collar to the front ofthe ERT Gateway. The following illustration shows the correct positioning.6. Secure the antenna collar to the top of the ERT Gateway using screws and washers.Tighten the screws to 5 to 6 inch-pounds.Installing the ERT GatewayERT Gateway Installation Guide TDC-1744-000 11Proprietary and Confidential

Attaching the backhaul antennaWarning: Install only the provided backhaul antenna. The backhaul antenna isdirectional. Position the ERT Gateway observing the antenna coverage area.The antenna effective range is approximately 100 feet from the front (1) of the ERTGateway and approximately 50 feet to the rear (2) of the device. The showncoverage area assumes the device is mounted at a height of 25 feet with a clearline-of-sight path between the ERT Gateway and the programming device.Positioning the ERT Gateway observing the coverage area guidelines ensures safepersonnel positioning for device programming.1. Remove the backhaul antenna from the shipping box.2. Remove the red connector protector.3. Thread the antenna onto the N-connector (labeled WAN) on the bottom of the ERTGateway.Important: Do not over-tighten or cross-thread the backhaul antenna.Installing the ERT GatewayERT Gateway Installation Guide TDC-1744-000 12Proprietary and Confidential

Table : Mounting HardwareComponent Image DescriptionMounting plate Mounting plate dimensionsMountingbracketsBrackets for wall-mountingBrackets for pipe or pole mounting (bracket dimensions areshown)Mounting bolts Bracket mounting boltsInstalling the ERT GatewayERT Gateway Installation Guide TDC-1744-000 14Proprietary and Confidential

Component Image DescriptionMiscellaneous Mounting nuts, set screws, washers, split washers, and anti-seize lubricantThe integrated mounting support on the back of the ERT Gateway housing slides into theslot in the center of the mounting bracket. A set screw locks the ERT Gateway to themounting bracket. The housing orientation can be adjusted ± 16 degrees horizontal tocompensate for different angles.Mounting the ERT Gateway on a pipeIn these instructions, the mounting plate is attached to the vertical pipe with the mountingbrackets. The ERT Gateway housing is secured to the mounting plate.1. Use the two mounting brackets and four bolts to attach the mounting plate to the pipe.2. Place the gateway on the mounting plate with the antenna in an upright position. Insertthe mounting plate disc into the mounting plate's disc opening.3. Secure the ERT Gateway to the mounting plate using the four set screws.Installing the ERT GatewayERT Gateway Installation Guide TDC-1744-000 15Proprietary and Confidential

Mounting the ERT Gateway on a pole1. Follow the pipe mounting procedure for securing the mounting plate to the ERT Gateway(see Mounting the ERT Gateway on a pipe on page 15). Ensure that the ERT GatewayERT antenna is in an upright position.2. Attach the ERT Gateway/mounting bracket assembly to the pole using the mountingbrackets or the optional metal straps.Mounting the ERT Gateway on a davit armThese instructions describe a typical utility or street light pole installation. The ERT Gatewayis mounted on a davit or street light arm.Power is supplied on a davit or street light arm installation using a photocell adapter cable.The cable plugs into the photocell sensor of the street light. If the ERT Gateway is mountedon a davit arm without a street light, the power cable must be connected according to thelocal electrical codes.Important: If a photocell adapter cable supplies power to the ERT Gateway, the gatewaymust be grounded through the grounding lug on the bottom of the housing.1. Use the two mounting brackets and four bolts to attach the mounting plate to the davitarm.Installing the ERT GatewayERT Gateway Installation Guide TDC-1744-000 16Proprietary and Confidential

2. Insert the mounting disc into the mounting plate disc opening.3. Using the set screws, secure the gateway to the mounting plate with the antenna in anupright position.Connecting the ground wireConnect the ground wire to the grounding lug on the ERT Gateway.Note: Due to variable requirements for cable length, cables are not provided by Itron.Attach the grounding wire to earth ground. Follow local codes if earth ground is not providedthrough the AC power cable.Connecting the ERT Gateway powerThe final step of the ERT Gateway installation is to provide power. A three-pin (AC) cable isrequired.Warning: Securely mount the ERT Gateway before the dedicated AC mains powersource is connected. The ERT Gateway must be grounded by the ground wire in thethree-wire AC mains cable or through the grounding lug on the bottom of thegateway. For installations connected to the photocell adapter, use the grounding lugto ground the gateway.Installing the ERT GatewayERT Gateway Installation Guide TDC-1744-000 17Proprietary and Confidential

Connecting the power cable1. Plug the power cable into the power connector on the bottom of the ERT Gateway.Note: The connector is keyed so the cable connects in the proper orientation.2. Secure the cable by tightening the retaining nut on the cable.ERT Gateway wiring diagramPower source and grounding connection are shown in the following illustration.Connection Description1 AC power sourceInstalling the ERT GatewayERT Gateway Installation Guide TDC-1744-000 18Proprietary and Confidential

Connection Description2 GroundInstalling the ERT GatewayERT Gateway Installation Guide TDC-1744-000 19Proprietary and Confidential

Chapter 5 OpenWay Riva Routing NodeCommunications SoftwareThe OpenWay Riva Routing Node ERT Gateway Star communicates using the OpenWayOperations Center Collection Manager. The OpenWay Operations Center CollectionManager sends a request to the ERT Gateway Star requesting the data from the previous 8hours. The ERT Gateway Star responds with the data that it stored over the past 8 hours.For more information, see the OpenWay Operations Center Collection Managerdocumentation (ERT Gateway related documents on page 3).ERT Gateway Installation Guide TDC-1744-000 20Proprietary and Confidential

Appendix A ERT Gateway SpeciﬁcationsThis section provides OpenWay Riva Routing Node ERT Gateway product specifications.Dimensions and weightThe ERT Gateway weight is listed in pounds. The dimensions are shown in inches.Component WeightERT Gateway 5.5 lbs (with antennas)Pole mounting kit 3 lbsWall mounting kit 2 lbsAntenna speciﬁcationsThis section provides the specifications for the 915MHz and backhaul antennas. The ERTGateway is designed to operate with the antennas listed here. Antennas not listed here arestrictly prohibited for use with the ERT Gateway. The required antenna impedance is 50ohms.Specification 915 MHz ERT antenna 915 MHz backhaul antennaItron part number* MSE-0330-001 MSE-0453-001 514618-001 MSE-0452-001Frequency range 902-932 MHz 902-928 MHz 902-928 MHz 902-928 MHzMaximum gain 5.15 dBi 5.5 dBi 1 dBi 2.6 dBiHorizontalbeamwidthOmnidirectional Omnidirectional Omnidirectional OmnidirectionalImpedance 50 ohms 50 ohms 50 ohms 50 ohmsTermination Type N male Type N Male Type N male Type N maleOverall length 18 in. 18.8" 5.6" 8"Radome diameter 1" OD 1" OD 0.84" OD 1" OD*See the OpenWay Riva Routing Node Ordering Guide (PUB-1306-001) for availability orcontact your Itron representative.ERT Gateway Installation Guide TDC-1744-000 21Proprietary and Confidential

To reduce potential radio interference to other users, select an antenna type with gain suchthat the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted forsuccessful communication.Antenna ConformityThese radio transmitters have been approved to operate (with the antenna types listedpreviously) with the maximum permissible gain and required antenna impedance for eachantenna type indicated. Antenna types not included in this list (those having a gain greaterthan the maximum gain indicated for that type) are strictly prohibited for use with thesedevices.Environmental speciﬁcationsThe ERT Gateway meets the listed environmental specifications.Specification ValueOperating temperature -40°C to 60°CStorage temperature -40°C to 85°CHumidity 0 to 90% non-condensingTransmitterThe ERT Gateway transmitter meets the listed specifications.Specification ValueMaximum transmit power at ERT antennaMaximum transmit power at backhaul antennaFrequency band 902 to 928 MHz (USA/Canada)ERT Gateway power operating rangeThe ERT Gateway meets the listed power operating ranges.Specification ValueVoltage (AC) 102 VAC to 264 VACFrequency 47 to 63 HzAverage power 5 wattsERT Gateway SpecificationsERT Gateway Installation Guide TDC-1744-000 22Proprietary and Confidential