J Brasch 73200675 Wireless Sensor Adaptor User Manual T500NRX US 10 08 10 r1
J. Brasch Co. Wireless Sensor Adaptor T500NRX US 10 08 10 r1
J Brasch >
Manual
SafePresence Hook-Up
Wireless
Link
Product Manual & Warranty
Contents
Safety Instructions
2
Product Overview
4
Product Diagrams and Functions
4
Connecting to the Call System
5
Setting up the SafePresence Hook-Up Wireless Link
6
Programming the transmitter to the receiver
6
Deleting a memory ID
7
Notes for bedside pads
7
Troubleshooting
8
Specifications
8
Warranty
9
Before Using the SafePresence Hook-Up Wireless Link
Be sure to read this manual thoroughly before use and to keep this manual
in a safe place for future reference. The
SafePresence
Hook-Up Wireless Link
is designed to assist a caregiver in monitoring another person. It is not a
substitute for
watchfulness
over individuals who may be at risk of injury from
falls. Additional
interventions
may be required.
Safety Instructions
Before using, please be sure to read this safety manual
carefully.
Product specifications described in this material are subject to
change
without
notice.
Hazard
definitions
The following terms are used throughout this manual to bring attention to the presence of
hazards and various risk levels, or to important information concerning the use of this product.
Warning
Caution
Indicates an imminently hazardous
situation
which,
if not avoided, may result in death
or
serious
injury.
Indicates a potentially hazardous
situation
which,
if not
avoided, may result in injury
or
property
damage.
* “Caution” indicates a potentially hazardous situation which,
if
not avoided,
may result in minor or moderate
injury.
Example of Hazard
Indicators
Caution
including
warning
Important precautions
Must follow the
instruction
Warning
IMPORTANT
SAFETY INSTRUCTIONS
Unplug the SafePresence Hook-Up Wireless Link from the AC power and refer servicing
to qualified service personnel under the following conditions.
In case of any abnormality such as smoke, hot smell or unusual
noise;
or
If water or any other liquid is spilled into or onto the SafePresence Hook-Up
Wireless Link; or
If power socket or cord is extremely hot;
or
If the SafePresence Hook-Up Wireless Link has been dropped
or
damaged.
Do not disassemble or alter the product
Do not attempt to
disassemble
or
alter the
product. It
may
cause fire and electric
shock.
Contact your distributor
for
inspection,
adjustment
and
repair.
Keep Dry
Keep this product dry and
away
from
water
or other liquids. Failure to
keep
dry may result
an electric
shock.
2
Precautions when using the AC adapter
If the provided plug
does
not
fit into
your outlet, do
not
use and contact
your
distributor for
further
information.
Do not bundle the AC
power
cord.
If a power strip or
extension
cord is used
with
this
product,
make sure that
the
total
of the ampere ratings
on
the products
plugged into
the
extension cord or
power
strip do not exceed the
extension
cord/power
strip’s
ampere
rating.
Do not tamper with the AC adapter
cord
Follow the instructions below; failure to
do so may damage the cord.
Operate this product only with the
specified voltage
Use the SafePresence
Hook-Up
Wireless Link
with the
speci
ed voltage
(AC
110V). Failure
to do so may cause a re
or
an electric
shock
.
Do not put heavy items on the cord.
Do not modify the cord.
Do not forcefully bend the cord.
Do not use the cord if damaged.
Do not twist or pull the cord.
Do not put close to heating materials.
Ask your distributor for an exchange if
the AC adapter cord is damaged. Failure
to do so may result in fire or electic shock.
Keep dry at all times
If water/liquid spills or enters the product,
it may cause a fire or an electric shock.
Inspect the plug and the AC power outlet
regularly
Remove the dust and dirt between the
plug and the outlet regularly. Failure to
do so may result in short circuit and fire.
The normal operation of this product may be disrupted by electro magnetic interference. If this
occurs, please reset the product to resume normal operation by following directions in the
instruction manual. If the product does not resume normal operation, please relocate the source
of the interference or use the product in a different location.
Handle the AC adapter with caution Do not place heavy objects on top of
the SafePresence Hook-Up Wireless Link.
Do not plug in or unplug the adapter
with wet hands. It may cause an electric
shock.
Never pull on the cord when
unplugging from the electrical outlet.
Always grasp the AC cord plug when
unplugging.
Do not use the product with an
electrical blanket or other electrical
items
This may cause a damage to the
product or an electric shock.
Set up precautions
Avoid use in an excessively humid,
dusty or steamy area.
Avoid direct sunlight.
The socket-outlet should be
easily accessible and located near
the equipment.
Rechargeable Battery Cautions
Follow the instructions below. Failure to do so
may cause the battery to leak or explode,
which may lead to fire or injury.
Use the specified rechargeable battery only.
Replacing the battery with an incorrect type
of battery may cause an explosion.
Never disassemble the battery.
Non-rechargeable batteries must not
be recharged.
Remove the batteries when not using
the device for an extended period of
time.
Battery disposal
warning
Never dispose of any battery by fire.
All batteries should be disposed of in
accordance with applicable local laws.
Dispose of used batteries according to the
instructions.
Do not set up on an unstable surface
When not in
use
For your safety, unplug the AC adapter
from the outlet.
3
4
This product is used to wirelessly connect various sensors to the call system.
Features:
• Up to three transmitters can be programmed to a receiver.
• Receiver can be set up to make an alarm sound upon detecting an alarm call.
*Alarm sound is turned off when it is shipped from the factory.
SafePresence Hook-Up Wireless
Link
-front-
Power LED light
Call LED light
-top-
Power switch
POWER
CALL
-side-
AC adapter jack
RECEIVER
6V
DC
-
+
AC
Adapter
Call System
connector
-back-
Floor Sensor
Transmitter
Memory switch
Bed/Chair
Transmitter
Transmitter
Alarm
LED
light
Transmitter
Floor
Sensor
Bed/Chair Sensor
5
Connecting
to the call system
• Connect the sensor to the transmitter.
• Connect AC adapter to the receiver and plug into the call system’s socket plug.
• Turn the power on.
Call System
wall socket
plug
Bed
sensor
mat
Floor
sensor
mat Chair
sensor
mat
RECEIVER
Transmitters
SafePresence
Hook-Up
Wireless Link
Trans mitter
Trans mitter
W i r el e s s
An additional adapter may be needed to connect the SafePresence Hook-Up
Wireless Link to your system.
*Check the call system wall plug socket to see what type of connector is required.
Be sure to use only SafePresence™ bed/chair sensor mats. Other products
may fail or not function properly.
1.
2.
Setting
up
the
SafePresence
Hook-Up Wireless Link
Installing the Receiver:
1.
Plug the SafePresence Hook-Up
Wireless Link into the call system wall
outlet.
2.
Insert the AC adapter plug into the AC
adapter jack on the side of the
SafePresence Hook-Up Wireless Link,
then plug the AC adapter into an
electrical outlet.
3.
Turn the SafePresence Hook-Up
Wireless Link power on and make sure
the Power LED light turns on.
Programming the
SafePresence
Hook-Up Wireless Link
• Program the Transmitter to the
SafePresence Hook-Up Wireless
Link before use.
• Up to three transmitters may be
programmed to the SafePresence
Hook-Up Wireless Link.
SafePresence Hook-Up
Wireless Link
(back)
Memory switch
Press down
with a paperclip
Setting up the Transmitter:
Connect the sensor to an appropriate
transmitter. Make sure to use correct
transmitter for the sensor.
Confirm the Link:
The SafePresence Hook-Up Wireless
Link’s call LED light will turn on for one
second upon receiving a signal from a
transmitter and then its responses will
immediately be sent to the call system.
Obstacles in the wireless path may
cause a shorter transmission range.
Please test thoroughly in all locations
where the product will be used.
On the back of the receiver, press
down on the Memory switch with a
paperclip, then turn the power on.
The green Power LED light will
turn on. The red Call LED light will
turn on for a second and then turn
off.
Release the Memory switch.
Connect a sensor to the
appropriate transmitter. Activate
the sensor. The Call LED light on
the receiver will turn on for a
second and then turn off.
3.
Repeat these step to set up
multiple transmitters. Turn off the
power to finish the programming
process.
6
1.
3.
Deleting a memory ID
SafePresence Hook-Up Wireless Link
(back)
Memory switch
(press down with a paperclip)
Use a paperclip to press down and hold the Memory switch on the back of
the SafePresence Hook-Up Wireless Link, then turn the power on.
The green Power LED light will turn on and the red Call LED light will turn
2.
on for a second and then turn off.
Hold the Memory switch down for about 5 seconds. The red Call LED light
will turn on.Turn off the power on the SafePresence Hook-Up Wireless
Link to complete the process.
All memory IDs will be deleted.
Notes for bedside pads
Some mattresses, including certain types of foam mattresses, may be too
soft for the sensor to work properly. The sensor may need to be placed
on a firmer surface.
Make sure the bedside pad is placed properly.
7
Problem Cause Solution
The Power LED light is not
turned on when the power is on.
The AC adapter is not Connect the AC adapter
connected properly. properly.
Transmitter is not properly Delete the memory and
registered on the receiver. register the transmitters again.
Remove electrical devices or
interfering obstacles.
Send LED light on the
transmitter is turned on, but the
Call LED light on the receiver
is not turned on.
Transmitter and receiver
are out of range.
Move the receiver/transmitter
closer together.
Call LED light on the receiver
turns on, but the call system is
not activated.
The SafePresence Hook-Up Connect the SafePresence
Wireless Link is disconnected Hook-Up Wireless Link to the
from the call system. call system.
Transmitter cannot be
registered to the SafePresence
Hook-Up Wireless Link.
3 transmititters are already Delete the memory and
registered. register the transmitters again.
Specifications
SafePresence Hook-Up Wireless Link
TXF
Floor Sensor
TXB
Bed/Chair Transmitter
Power
AC Adapter
120V
60Hz
DC6V 100mA
CR2032(3V)
Power
consumption
3.4W app.
Size (mm)
68 x 100 x 26
51 x 71 x 13
Weight (g)
100
60
40
Operating
condition
temperature 5
-
40C°
Humidity 45
-
85%
Frequency
2.4GHz
Applicable
standard
ARIB STD-T66
Battery life
2 years app.
*Please contact us to replace the battery for the transmitter.
8
DOC 16.73200.12
9
1.
Manufacturer warrants to the original purchaser that the SafePresence Hook-Up
Wireless Link will be free from defects in materials and workmanship for a period of
one (1) year from the date of purchase.
2.
During this period, the manufacturer will perform repairs or effect replacement
at manufacturer’s option at no charge.
3.
Manufacturer's limited warranty covers only those defects that arise as a result
of normal use of the hardware and does not apply if:
a. Damage or fault caused by use against instructions, warnings or cautions.
b. The serial number has been altered, defaced or removed.
c. Defect or damage caused by or resulting from unauthorized service or parts.
d. Defect or damage that occurs due to fire, earthquake, flood damage, thunderbolt,
other natural disasters, environmental pollution or irregular voltage sources.
e. Damage caused by misuse, abuse, accident, neglect or mishandling.
f. Failure caused by or resulting from unauthorized service or parts.
Item
Number
SafePresence Hook-Up
Wireless Link
Serial
Number
One year warranty
from the date
of purchase
Customer
infomation
J. Brasch Co., LLC
140 N 8th St.
Suite 430
Lincoln, NE
TEL: (402) 476-2858
FAX: (402) 476-2866
DOC 16.73200.12
10
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
NOTE:
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR
TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS
TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE
USER AUTHORITY TO OPERATE THE EQUIPMENT
NOTE:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.