J and M CFRG-BT01 Bluetooth Adapter User Manual jm 182 CFRG BT01 qxp

J&M; Corporation Bluetooth Adapter jm 182 CFRG BT01 qxp

user manual

#CFRG-BT01Bluetooth®AdapterFor J&M CFRG UnitsInstallation and OperationInstructions© 2006 J&M Corporation. All rights reserved. 6/06
Universal CellularTelephone/GPS/RadarDetector AudioIntegration TerminalCell PhoneGPSright-angle plug to the GPS audio output(GPS not included)CFRG-Moduleblack2-pinplugblack2-pinplugblack wire—groundconnectionblack wire—ground connectionred wire—power connection for radar detectorred wire—power connection for GPSdriver's helmet headset(not included)5-pin dinred6-pin plugcell phonerocker control switchfactory-installed headset leadwhite3-pinplug black3-pinplugRadar Detectorblack2-pin plug5-pin headset lead fromstock audio system5-pin dinfuse holderground to frame—black wire12v swithable—red wirevolumemultifunctionbuttonred 4-pinplugCFRG-BT01Diagram A
Thank you for the confidence you have shown by purchasing oneof J&M’s innovative products. If you have any questions during theinstallation, or require further assistance, you may call us at 1-800-358-0881 from 8:00 a.m. to 5:00 p.m. Mountain StandardTime, Monday through Friday.Tucson, Arizona U.S.A.Tel (800) 358-0881Website: http://www.jmcorp.comE-mail: audio@jmcorp.comInstallation1. Mount the CFRG-BT01 where desired, taking into considerationthe wire lengths going to the CFRG unit to allow easy access tothe control buttons.2. Connect the 4-pin red plug from the CFRG-BT01 to the 4-pin redplug on the CFRG unit.3. Connect the black 2-pin plugs in series between the CFRG unitand the radar detector. (See Diagram A)Operation1. Turn on the motorcycle ignition and then depress and hold themultifunction button located on the top of the CFRG-BT01 until theblue LED stops flashing then release the button.2. Now depress and hold the button on the CFRG-BT01 for 10 seconds. The LED should now be flashing rapidly to indicate pair-ing mode.3. Enable the Bluetooth mode on your cell phone and perform adevice discovery from the phone. (Refer to your cell phone’s userguide)4. Select the J & M Cell/Nav from the list of devices.5. When prompted by the phone, enter passkey 0000 and confirmto pair your cell phone to the CFRG-BT01.6. The CFRG-BT01 is paired with your phone when the LED goesfrom rapidly flashing to a slower flash.7. The multifunction switch allows you to answer incoming cellphone calls (if not in auto answer mode), voice command dialingfeature along with pairing the CFRG-BT01 to a Bluetooth enabledcell phone or Bluetooth enabled navigation device.8. To answer an incoming call briefly depress the multifunctionbutton (if not in auto answer mode) and switch the on/off rockercontrol switch from the CFRG to the on position.9. To activate the voice command dialing function of the phone —“turn on”, the on/off rocker switch from the CFRG and brieflydepress the multifunction button on the CFRG-BT01.10. Once enabled and linked, the CFRG-BT01 will turn off and onautomatically with the motorcycle ignition switch.Noise and InterferenceMotorcycle audio systems by their very nature are noisy. While wedo not guarantee this system to be completely free from electricalnoises and interference, we have taken many steps to achievethat goal: the power supply system is well filtered, the unit isshielded in its metal container, and the cables associated with theunit are shielded.Power requirements: 11-16 volts DC negative groundMinimum speaker impedance: 32Typical current draw: 1.5 ampsChanges or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority to operate the equipment.FCC RegulationsThis device complies with 15 of the FCC Rules. Operation is sub-ject to the following two conditions: (1) This device may notcause harmful interference, and (2) this device must accept anyinterference received, including interference that may causeundesired operation.Industry Canada Notice to UsersOperation is subject to the following two conditions: (1) Thisdevice may not cause interference and (2) This device mustaccept any interference, including interference that may causeundesired operation of the device Ref IC RSS 210 Sec. 5.11.The term”IC:” before the certification/registration number onlysignifies that registration was performed based on a Declarationof Conformity indicating that Industry Canada technical specifica-tions were met. It does not imply that Industry Canada approvedthe equipment.

Navigation menu