JBL CBT_200 Installation Bracket Guide CBT 200 120712
CBT_200 Installation Bracket Guide 120712 JBL - Manuals+
User Manual: JBL JBL CBT 200LA-1 | 200 cm Tall Constant Beamwidth Technology™ Line Array Column Speaker
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
CBT 200LA-1 Assembly & Bracket Installation Guide INCLUDED: Top Speaker Module Bottom Speaker Module Speaker Bracket Coupler Plate M6-34L M6-12L M6-Nuts SS Lockwashers Swivel-Tilt Wall Bracket SS Flatwashers M6-20L Flat head [Not shown to relative scale] Switch covers CBT 200LA-1 Assembly & Bracket Installation Guide – Page 2 WALL SURFACE MOUNTING Note that the BRACKET ASSEMBLY consists of a SPEAKER BRACKET and a WALL BRACKET. 1) RUN WIRING -- Run the wiring from the power amplifier to the location desired for mounting the JBL CBT Loudspeakers. 2) ATTACH WALL BRACKET TO WALL -- Using a level to ensure that the WALL BRACKET is straight, secure the WALL BRACKET to the wall. Be sure to use the appropriate wall anchors for attaching the bracket. Use all four screw holes for maximum integrity and safety. Be sure that the slot feature is at the top. Hardware for attaching WALL BRACKET to wall not included. CBT 200LA-1 Assembly & Bracket Installation Guide – Page 3 3) ORIENTING TOP & BOTTOM SPEAKER MODULES This drawing shows the proper orientation of the two speaker modules, where the coupler plate attaches and where the wall bracket attaches (onto the coupler plate). IMPORTANT: Note that the speaker will not work correctly if the TOP AND BOTTOM SPEAKER MODULES are not oriented exactly as shown. Switches at the End of the Column TOP SPEAKER MODULE Labels Show Orientation and Gives Instructions (Point Arrows Toward Each Other) For Top Module: CBT 200LA-1 Assembly 1) Align Top & Bottom Speaker Modules So Arrows Point at Each Other Swivel/Tilt Wall Bracket (4 panhead bolts) 2) Attach Coupler Plate Using 8 Included Flathead Bolts Coupler Plate (8 flathead bolts) CAUTION: Installation must be done by qualified persons using safe rigging standards. CBT 200LA-1 Assembly 1) Align Top & Bottom Speaker Modules So Arrows Point at Each Other 2) Attach Coupler Plate Using 8 Included Flathead Bolts CAUTION: Installation must be done by qualified persons using safe rigging standards. CBT 200LA-1 Assembly 1) Align Top & Bottom Speaker Modules So Arrows Point at Each Other For Bottom Module: 2) Attach Coupler Plate Using 8 Included Flathead Bolts CAUTION: Installation must be done by qualified persons using safe rigging standards. CBT 200LA-1 Assembly 1) Align Top & Bottom Speaker Modules So Arrows Point at Each Other 2) Attach Coupler Plate Using 8 Included Flathead Bolts CAUTION: Installation must be done by qualified persons using safe rigging standards. BOTTOM SPEAKER MODULE Switches at the End of the Column CBT 200LA-1 Assembly & Bracket Installation Guide – Page 4 4) CONNECT SPEAKER MODULES TOGETHER VIA COUPLER PLATE Attach COUPLER PLATE to the TOP AND BOTTOM SPEAKER MODULES, as shown, with 8 pcs of M6-20L flathead bolts, through to TOP AND BOTTOM SPEAKER MODULE’S rear cabinet insert points. 5) ATTACH SPEAKER BRACKET TO 4 THREADED HOLES ON COUPLER PLATE Attach Speaker Bracket to the 4 indicated threaded points on the Coupler Plate using the included M6-12L (6 mm diameter, 12 mm long) bolts, with lock washers and flat washers. M6L12 BOLT LOCK WASHER FLAT WASHER Threaded points for attachment of Wall Bracket (use included M6 x 12 mm pan-head bolts) [4 Places] Speaker Section of Speaker/Wall Bracket Assembly Threaded points for attachment of Wall Bracket (use included M6 x 12 mm pan-head bolts Coupler Plate (already installed on speaker) IMPORTANT: Because of the height of this speaker, the speaker bracket MUST be installed to these threaded points on the Coupler Plate. Do NOT install the bracket to any other positions on the speaker. CBT 200LA-1 Assembly & Bracket Installation Guide – Page 5 6) SLIDE SPEAKER WITH SPEAKER BRACKET ONTO WALL BRACKET n Once the wall mount has been attached to the wall and speaker mount has been attached to the speaker, loosely install the M6-L34 PIVOT BOLT (bolt, lock washer and flat washer on one side and flat washer, lock washer & nut on the other side) of the WALL BRACKET. Then slide the speaker so that the SPEAKER BRACKET engages into the WALL BRACKET, dropping the hook slot of the SPEAKER BRACKET onto the PIVOT BOLT (which will already be installed loosely in the WALL BRACKET), as M6 NUT shown in Drawing n . LOCK WASHER FLAT WASHER FLAT WASHER LOCK WASHER M6-34L BOLT [Same hardware order for both bolts] PIVOT BOLT LOCATION 1 2 3 CBT 200LA-1 Assembly & Bracket Installation Guide – Page 6 o Insert the top tilt-angle bolt through the appropriate hole – one of the preset angle holes or the slot for continuous adjustment capability (see below for more information about tile angles). Install with M6-L34 bolt, lock washer and flat washer on one side and flat washer, lock washer & nut on the other side, as shown in Drawing o . Make sure bolt goes through holes in WALL BRACKET and in SPEAKER BRACKET. p Final BRACKET ASSEMBLY is shown in Drawing p . TIGHTEN THE BOLTS. 7) MORE ABOUT TILT ANGLES -- The bracket allows for +/-15 degrees of up or down tilt, however because of the height of this speaker, the end of the speaker hits the wall at any angle greater than 10 degrees. PRE- SET ANGLES and CONTINUOUSLY VARIABLE ANGLE -- The bracket has through holes for mounting angles of +/- 15 degrees in 5 degree increments. There is also a slot above the set of holes for continuously variable adjustment. The pre-set angles are recommended for accurate aiming in 5 degree increments and the slot for any angle between 5 degree increments. Either can be utilized for setting the speaker’s tilt angle. 8) SET THE SWIVEL (PAN) ANGLE – Loosen the top and bottom bolts on the pivot. Adjust the side-to-side swivel (ie, pan) aiming angle of the speaker. Tighten the bolts securely. Maximum Swivel Angles before Wall Interference – The bracket swivels a full 90 degrees from side-to-side, however when mounting the CBT speaker onto a wall, the side-to-side swivel is limited by the end of the speaker encountering the wall. The maximum swivel angle depends on the up/down tilt angle setting. 9) SAFETY CABLE -- Attach a safety cable (not included) to any of the 6 mm inserts on the back of the CBT 200LA-1 cabinet using one of the extra included M6 bolts or via an M6 forged shoulder steel eyebolt. Attach the other end of the cable to a secondary attachment point on the wall. 10) SWITCH COVERS – To discourage tampering with the switch settings, adhesive switch covers are provided. Peel off the backing from the switch cover and stick the cover over the switch shaft, lining up the ridge with the recess in the switch shaft. CBT 200LA-1 Assembly & Bracket Installation Guide – Page 7 11) USING OPTIONAL MTC-CBT-FM1 FLUSH-MOUNT WALL BRACKETS – The optional MTCCBT-FM1 brackets allow installing the speaker with its back very close to the wall. It is recommended to use two brackets – one on the top and one on the bottom – for stability. CBT 200LA-1 Assembly & Bracket Installation Guide – Page 8 CBT 200LA-1 Bracket Dimensions JBL Professional 8500 Balboa Blvd. Northridge, CA 91355 USA CBT200 Install 07/12
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0.5 (Windows) Create Date : 2012:07:12 11:30:33-07:00 Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2012:07:12 11:30:33-07:00 Format : application/pdf Title : Microsoft Word - CBT_200 Installation Bracket Guide.doc Creator : rkamlet Document ID : uuid:6a9641f3-8b1e-4524-89ad-8e173687e804 Instance ID : uuid:954df8b6-132e-440d-b823-ced615d39b48 Page Count : 8 Author : rkamletEXIF Metadata provided by EXIF.tools