JSW Pacific APPCAM26PTA 720p PT WIFI Camera User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2646458
Application ID	P98mN0DGRB4IZPVwQ1rASA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	47.66kB (595791 bits)
Date Submitted	2015-06-12 00:00:00
Date Available	2015-06-14 00:00:00
Creation Date	2015-06-02 17:16:48
Producing Software	Adobe Acrobat Pro 11.0.8
Document Lastmod	2015-06-02 17:16:48
Document Title	User Manual
Document Creator	Adobe Acrobat Pro 11.0.8

Quick-Start Guide
Guardian App Cam 26
IP Camera
Use this Quick-Start Guide to connect the camera to the network.
If you want to set up more cameras later, refer to the online user
manual for instructions.
In the Box
•
•
•
•
•
•
•
Camera (x1)
Antenna (x1)
Mounting Bracket (x1)
Ethernet Cable (x1)
AC Adaptor (x1)
Screw Pack
Quick-Start Guide
If any item is missing or damaged, contact your place of purchase
immediately. Never use damaged products!
Need help? Get answers at our website:
www.uniden.com.au for Australian model
Important Safety Instructions
1. Do not drop, puncture or disassemble the camera.
2. This camera is NOT waterproof.
3. Never tug on the power cords. Use the plug to unplug it from the wall
outlet.
4. Do not expose the camera to high temperature or leave it in direct
sunlight. Doing so may damage the camera or cause camera
temporary malfunction.
5. For your own safety, avoid using the camera or power off the camera
when there is a storm or lightning.
6. Remove the power adaptor during long periods between usages.
7. Use only the accessories and power adaptors supplied.
Getting to know your Guardian App Cam 26
Light Sensor
Infrared LEDs
Microphone
LAN Port
Reset
Antenna
Connector
MicroSD Card Slot
Status LED
Power Input
Set Up Camera, Smartphone and Tablet
This QSG only shows images for Android devices. Images for iOS devices
are similar.
Prerequisites
• Your router must support WPA/WPA2 security and it must be turned
on.
• You must have an available WiFi-enabled mobile device (Android or
iOS smartphone/tablet).
• The Guardian App Cam 26 and your mobile device must connect to
the same WiFi router for setup.
1. Download the Guardian App (search for Uniden® AppCam™) from the Apple App store
(iOS) or Play Store (Android) on to your device.
2. Connect the antenna to the camera. You can
attach the camera stand to the camera as well,
but it is not necessary.
3. Connect the camera to power. After about 45
seconds, the green LED begins to flash (3-flash/
pause pattern).
Make a note of your DID code. It can be found on the base of the camera.
Connect Camera and Mobile device
1. From your mobile device’s Settings, go to WiFi. Select the Camera
WiFi ID to connect your device to it. The camera WiFi ID will be HDXXXXXX, where XXXXXX are the last 6 digits on the DID code.
(If you cannot find the camera’s WiFi ID, try refereshing the WiFi list
on your mobile device.)
Enter the default password, 12345678.
2. When the device is connected to the camera, launch the app and
tap the Add New System
icon.
3. The System Information screen displays. Name the camera and tap
Search.
4. The Search in LAN results box displays. The camera’s DID should
display. Tap the DID number (or tap Join for iOS).
5. The System Information screen displays again. This time, enter the
security code (123456); tap Save. Tap YES (OK) at the next prompt.
6. The Snapshot screen displays. Tap the relevant Snapshot to access
the Guardian App Cam 26 LIVE view.
When connected to the LIVE view for the first time, the user is forced to
change the security code.
Connect Camera to wifi router
1. In LIVE view, tap the Back icon,
the System icon, and then the
System Settings icon. The System
Information screen displays.
2. Tap Advanced. Enter the Admin
password (123456).
3. Scroll to the option WiFi Setting
on the Advanced Settings list. Tap
Manage WiFi Network. Select
your router from the drop-down list
and enter your router’s password.
Tap Connect.
 your camera will reboot and
reconnect to the router. wait until the
camera’s led returns to the steady on
state to continue.
4. The Camera screen indicates
that it is disconnected. Tap the
System icon and then the Refresh
icon. The camera refreshes and
reconnects to the router you
chose. The LED should be steady
and the app displays the video.
Set Time Zone
It is important to set the correct time zone and daylight savings time
indication on your camera to ensure correct date/time stamp on the
video files.
1. Access the Advanced Settings list (see Connect Camera to Wifi
Router, described previously.)
2. From the Advancd Settings list, scroll to Time Zone.
3. Select your time zone.
4. Set the Daylight Savings Time indicator.
5. Tap Back, and exit the Advanced Settings list.
 For complete operation instructions, refer to the online user manual at
www.uniden.com.au
Mounting the Plate and Camera
1. Hold the mounting
plate where you want
to mount it and mark
the location of the
screw holes.
2. Use the included
screws and anchors
to attach the mounting
plate to the wall.
3. Use the enclosed
screws to screw the
camera to the bracket.
Troubleshooting
If...
Try This...
My smartphone
or wireless device
cannot find the
camera during setup.
Make sure the camera’s green LED is blinking
in a 3-flash/pause pattern. If it isn’t, reset the
camera by using a blunt pin to press and hold
the Reset button until the LED begin to flash.
The app cannot find
the camera
Make sure your network supports DHCP
protocol.
Make sure that the DHCP option is turned on.
Make sure the camera and your mobile device
connect to the same WiFi router.
Make sure the WiFi router is activated.
Make sure the camera is properly powered
on.
Make sure the WiFi router has enabled SSID
broadcasting.
The camera does
not find the router to
connect to
Make sure you selected the correct router in
the Manage WiFi Network box.
Make sure you entered the correct password
for the router you selected in the Manage WiFi
Network box.
Networking Parameter
Wireless Technology
IEEE 802.11 b/g/n
Network Connection
Ethernet (10/100 Base-T/Base -TX); WiFi
Simultaneous Viewers
3 concurrent sessions
Security
WPA /WPA2/WPA2-PSK (TKIP, 128 bit AES)
Camera Parameter
Image Sensor
Mega pixel CMOS
Local Storage
Micro SD Card, Class 10
Viewing angle
H:75°±3°, V45°±3°
Min. Illumination
1~8 lux
Number of LEDs
5 IR LEDs with IR switcher
IR Distance
5~8 meters
Video Audio Parameter
Image Compression
H.264
Image Resolution
HD 1280x720
Recording Frame Rate
720P@20 FPS
Supported Mobile Device
iOS requirement
iPhone 4S / iPad Mini / iPad 2 with iOS 6.0
or above
Android requirement
Android 4.1X or above
Hardware requirement
1.5GHz dual core or above
1GB or above internal memory, 960 x 540
pixel panel or above
General Parameter
Power Requirements
100~240V switching power supply DC 5V
1.5A
Operating Temp
-10°~+50°C
one-year limited warranty
Guardian App Cam 26
Important:
Satisfactory evidence of the original purchase is required for warranty
service. Please refer to our Uniden website for any details or warranty
durations offered in addition to those contained below.
Warrantor:
The warrantor is Uniden Australia Pty Limited ABN 58 001 865 498
(“Uniden Aust”).
Terms of Warranty: Uniden Aust warrants to the original retail
purchaser only that the Guardian App Cam 26 (“the Product”), will be
free from defects in materials and craftsmanship for the duration of the
warranty period, subject to the limitations and exclusions set out below.
Warranty Period: This warranty to the original retail purchaser is only
valid in the original country of purchase for a Product first purchased
either in Australia or New Zealand and will expire one (1) year from the
date of the original retail sale. If a warranty claim is made, this warranty
will not apply if the Product is found by Uniden to be:
A. Damaged or not maintained in a reasonable manner or as recommended
in the relevant Uniden Owner’s Manual;
B. Modified, altered or used as part of any conversion kits, subassemblies
or any configurations not sold by Uniden Aust;
C. Improperly installed contrary to instructions contained in the relevant
Owner’s Manual
D. Repaired by someone other than an authorized Uniden Repair Agent in
relation to a defect or malfunction covered by this warranty; or
E. Used in conjunction with any equipment, parts or a system
notmanufactured by Uniden.      
Parts Covered: This warranty covers the Product and included
accessories.
User-generated Data: This warranty does not cover any claimed loss of
or damage to user-generated data (including but without limitation phone
numbers, addresses and images)that may be stored on your Product.
Statement of Remedy: If the Product is found not to conform to this
warranty as stated above, the Warrantor, at its discretion, will either
repair the defect or replace the Product without any charge for parts or
service. This warranty does not include any reimbursement or payment
of any consequential damages claimed to arise from a Product’s failure to
comply with the warranty. Our goods come with guarantees that cannot
be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be of acceptable quality and
the failure does not amount to a major failure. This warranty is in addition
to and sits alongside your rights under either the COMPETITION AND
CONSUMER ACT 2010 (Australia) or the CONSUMER GUARANTEES
ACT (New Zealand) as the case may be, none of which can be excluded.
Procedure for Obtaining Warranty Service: Depending on the
country in which the Product was first purchased, if you believe that
your Product does not conform with this warranty, you should deliver
the Product, together with satisfactory evidence of your original
purchase (such as a legible copy of the sales docket) to Uniden at
the address shown below. You should contact Uniden regarding any
compensation that may be payable for your expenses incurred in making
a warranty claim. Prior to delivery, we recommend that you make a
backup copy of any phone numbers, images or other data stored on
your Product, in case it is lost or damaged during warranty service.
UNIDEN AUSTRALIA PTY LTD
Service Division
345 Princes Highway,
Rockdale, NSW 2216
Phone number: 1300 366 895
Email: custservice@uniden.com.au
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
The distance between user and products should be no less than 20cm
IC Statement:
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son fonctionnement est
soumis aux deux conditions suivantes :
( 1 ) Ce dispositif ne peut causer d'interférences ; et
( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer un
mauvais fonctionnement de l'appareil.
La distance entre l'utilisateur et de produits ne devrait pas être inférieure à 20cm

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2015:06:02 17:16:48+08:00
Creator                         : Adobe Acrobat Pro 11.0.8
Modify Date                     : 2015:06:02 17:16:48+08:00
Title                           : 
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2015:06:02 17:16:48+08:00
Creator Tool                    : Adobe Acrobat Pro 11.0.8
Format                          : application/pdf
Document ID                     : uuid:54c6c43d-15ac-4e43-8fd5-cb143181e7f4
Instance ID                     : uuid:5a1e5e27-0ada-46b8-8b36-d681f51f7ea0
Producer                        : Adobe Acrobat Pro 11.0.8
Page Count                      : 9

EXIF Metadata provided by EXIF.tools