JSW Pacific MSTR51 Smart wireless central home control / management center User Manual QSG SHC draft

Download:
Mirror Download [FCC.gov]
Document ID	2562544
Application ID	886H8GHK1K1h1rbrNi2cpg==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	86.87kB (1085841 bits)
Date Submitted	2015-03-22 00:00:00
Date Available	2015-03-22 00:00:00
Creation Date	2015-03-19 18:58:07
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2015-03-19 18:58:07
Document Title	QSG-SHC draft
Document Creator	PScript5.dll Version 5.2
Document Author:	hp

QUICK START GUIDE
KIT CONTENT
x1
Gayway
Adaptor DC12V/1A
IP Camera
Motion PIR
On / Off Switch
Door / Window
Sensor
Wireless day / night portable
motion alert indoor camera.
Remove the insulating plastic
Adaptor DC12V/1A
Adaptor DC12V/1A
x1
Ethernet cable 2M
x4
Sticky pad
x1
x4
Screw
x3
x4
Screw
Sticky pad
x1
Adaptor DC 5V/1 A
Panic Remote
IP Camera
Wireless multi-functional panic
remote controller.
NA
Battery CR2032
Indoor Siren
Panic Remote
Smart wireless central home
control / management center.
x1
x3
Battery AA 1.5V
Gateway
Ethernet cable 2M
x1
Adaptor DC 5V/1.5A
SYSTEM INTRODUCTION
x4
Battery AA 1.5V
x1
Bracket
x1
Battery CR2032
x2
Screw
Motion PIR
On / Off Switch
Indoor Siren
Door / Window Sensor
Wireless portable / wallmount area motion alert
sensor.
Wireless appliance energy
management power switch /
signal repeater (single device)
Wireless portable / wallmount alert siren.
Wireless door / window access
alert sensor.
Adaptor DC12V/1A
Serie No.
Battery AA 1.5V x 3
GETTING STARTED
or Battery AA 1.5V x 4
Remove the insulating plastic
(3) Launch the 'OMGUARD SHC' APP. Click the 'ADD'
icon
and choose 'Camera' to add the device to
system.
OMGUARDSHC
Follow the APP wizard setup process to add the
camera.
1. Connect the gateway box to the Internet
Note: The APP will search the available IP Camera in
LAN area. If the camera you're setting doesn't
appear in the searching list, please enter the
camera ID (DID) and password manually.
(1) Connect gateway box to your router via the Ethernet
cable. Then plug in the supplied power cable.
(2) The power LED indicator becomes steady RED and
you will hear the gateway box beep twice. This
means the gateway box is ready for APP setup.
(3) Launch 'OMGUARD SHC' APP. The APP will
automatically search the available gateway box and
brings up the system DID/password. If it is not
shown, Please check the system DID on the bottom
of the gateway box. Enter the system DID and default
password 123456 manually.
Steady RED
Installing the IP Camera:
(1) Secure the camera stand on the stable surface.
(2) Mount the camera into camera stand. Adjust the
viewing angle and fix the camera tightly.
OMGUARDSHC
3. Pair the Motion Sensor
Note: The gateway box should be powered on and
connected to the Internet at all times.
You can continue to setup the camera and sensor(s) now.
2. Set up the IP Camera
(1) Connect the IP Camera to your router via the
Ethernet cable .
(2) Plug in the power adapter and wait until both RED
and GREED LED begin flashing.
Note: DO NOT begin the APP setup process until both
LEDs become steady on.
Launch the 'OMGUARD SHC' APP. Click the 'ADD' icon
and choose 'Motion Sensor' and
to initiate the
pairing process, following with pressing the pairing
button located inside the battery compartment to
complete the process.
OMGUARDSHC
Installing the Motion Sensor:
(1) Place the motion sensor upward, facing the location
to be monitored. The detection distance is up to 16
meteres.
For maximum coverage, it is recommanded to place
the motion sensor highup with its back against the
corner of walls to ensure best detection coverage.
16 meters
(2) Use the double-sided tape to fix the motion sensor.
Using the mounting screws:
4. Pairing the Power Switch
Launch the 'OMGUARD SHC' APP. Click the 'ADD' icon
and choose ‘Power Switch' and
to initiate the
pairing process, following with press/hold the front
panel button until LED flashing blue.
(1) Fix the first mounting screw directly onto the door /
window frame (A). Place (hang) the larger piece on
to the mounted screw, remove the battery compart
ment cover to fix the second mounting screw (B).
OMGUARDSHC
To initiate the repeater function, press / hold the front
panel button turned orange, following with pressing the
pairing button on the device .
(2) Open back cover of the small piece. Use the
mounting screws to fix the back cover on the
movable part of the door/window frame (C).
Mount the senor onto the back cover.
Slot
(3) When it is finished, open the door or window to test
if the sensor has been correctly installed. You'll
receive an alert from the mobile device if the APP and
sensor have been corrected installed.
5. Pairing the Door / Window Sensor
Launch the 'OMGUARD SHC' APP. Click the 'ADD' icon
and choose 'Door Sensor' and
to initiate the
pairing process, following with removing and reinstalling
the battery compartment cover to complete the process.
OMGUARDSHC
6. Indoor Siren
Launch the 'OMGUARD SHC' APP. Click the 'ADD' icon
and choose 'Siren' and
to initiate the pairing
process, following with pressing the pairing button
inside the battery compartment to complete the
process.
Installing the Door/Window Sensor
Using the double-sided tape:
OMGUARDSHC
(1) Apply the double-sided tape to the backs of the
Door/Window sensor.
Installing the Siren:
(2) Select a location on the door/window. The large
piece of the sensor should be fixed on the immovable
frame of the door/window.
Align the small piece to the large one. Fix the small
piece on the movable part of the door/window
frame.
It is recommanded to install (wall-mount / place on flat
surface) the Siren in a highly visible location with
minimum obsticles near for maximum visual and sound
alert deterrence in critical situations. A/C power option
is available, choose a suitable power outlet location for
the installation.
(3) When it is finished, open the door or window to test
if the sensor has been correctly installed. You'll
receive an alert from the mobile device if the APP and
sensor have been corrected installed.
List of triggered events from device(s) and playback from
camera(s).
7. Pairing the Remote Control
Launch the 'OMGUARD SHC' APP. Click the 'ADD' icon
and choose 'Panic Remote' and
to initiate the
pairing process, following with press/hold the camera
button until the LED flashing blue.
OMGUARDSHC
Events
STATUS INDICATOR
8. APP Operation
Display device status in realtime. Tap "Status" to refresh
the status page.
ON
Status
Setup groups of devices for instant function activation /
deactivation.
1. Choose "+" to start a new "control".
2. Naming the control and select device(s).
3. Save.
Sensor On
OFF
Sensor Off
Sensor Triggered
Power Low
Vandal Alert
Delete
Edit Mode
Group
Setup various scenarios for system to launch preconfigured settings governing the behaviour of lights,
cameras and sirens.
1. Choose a device (initiator) from the list.
2. Choose "+" to add additional device (follower). Repeat
to add additional device(s).
3. Save.
Scenario
Example: "Motion PIR" (initator) > "Power Switch"
(follower) > "Save".
FCC Compliance Statement: This device complies with Part 15 of the
FCC rules. Operation is subjected to the following two conditions:
(1)this device may not cause harmful interference, and (2) this device
must accept any interferencereceived, including interference that
may cause undesired operation.
Products with CE Marking comply with EMC Directive (2004/108/EC);
Low Voltage Directive (73/23/EEC); R&TTE (1999/5/EC); ROHS Directive
(2011/65/EU) issued by the Commission of the European Community.
Compliance with these directives implies conformity to the following
European Norms:
EMC: EN 301 489
LVD: EN 60950
Radio: EN 300 328
If the camera system no longer functions or can no longer be repaired,
it must be disposed of according to the valid statutory regulations.
Disposal of spent batteries/accumulators:
You are required by law (Battery Ordinance) to return all spent batteries and
accumulators. Disposing of spent batteries/accumulators with common household waste
is prohibited! Batteries/accumulators that contain hazardous substances are marked
with the symbols on the side. These symbols indicate that it is prohibited to dispose of
these batteries/accumulators in the household waste. The abbreviations for the respective
heavy metals are: Cd=cadmium, Hg=mercury, Pb=lead. You can return spent batteries
and accumulators that can no longer be charged to the designated collection points in
your community, outlets or wherever batteries or accumulators are sold. Following these
instructions will allow you to fulfill the legal requirements and contribute to the protection
of our environment!
FCC Compliance Statement: This device complies with Part 15 of the FCC rules. Operation is
subjected to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
This device complies with Industry Canada’s licence-exempt RSSs.Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son fonctionnement
est soumis aux deux conditions suivantes :
( 1 ) Ce dispositif ne peut causer d'interférences ; et
( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer
un mauvais fonctionnement de l'appareil.
Changes or modifications not expressly approved by the party responsible for compliance could
void your authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : 3.1-702
Modify Date                     : 2015:03:19 18:58:07+08:00
Create Date                     : 2015:03:19 18:58:07+08:00
Metadata Date                   : 2015:03:19 18:58:07+08:00
Creator Tool                    : PScript5.dll Version 5.2
Format                          : application/pdf
Title                           : QSG-SHC draft
Creator                         : hp
Document ID                     : uuid:15246f6e-31ab-4789-8685-9450d8d4b29e
Instance ID                     : uuid:81327f3e-e2b9-45d3-addf-90c020fd283d
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Has XFA                         : No
Page Count                      : 3
Author                          : hp

EXIF Metadata provided by EXIF.tools