JVC KENWOOD 28451110 144/440MHz FM Dual Bander User Manual TM D700 E 00 Thank you

Download:
Mirror Download [FCC.gov]
Document ID	59321
Application ID	hWOP7iqrQK9glptnBRC78Q==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.74kB (259306 bits)
Date Submitted	1999-09-17 00:00:00
Date Available	1999-12-10 00:00:00
Creation Date	1999-07-21 14:04:57
Producing Software	Acrobat Distiller 3.02 for Power Macintosh
Document Lastmod	0000-00-00 00:00:00
Document Title	TM-D700 E 00 Thank you!
Document Creator	Adobe PageMaker 6.0
Document Author:	äCäOíSìñPVX

THANK YOU!
We are grateful you decided to purchase this
KENWOOD FM transceiver. KENWOOD always
provides Amateur Radio products which surprise and
excite serious hobbyists. This transceiver is no
exception. This time KENWOOD presents a mobile with
a built-in TNC to make data communications much more
convenient than before. KENWOOD believes that this
product will satisfy your requests on both voice and data
communications.
MODELS COVERED BY THIS MANUAL
The models listed below are covered by this manual.
TM-D700A: 144/440 MHz FM Dual Bander
(U.S.A./ Canada)
TM-D700E: 144/430 MHz FM Dual Bander
(Europe)
TM-D700A: 144/430 MHz FM Dual Bander
(General market)
FEATURES
NOTICES TO THE USER
One or more of the following statements may be
applicable:
FCC WARNING
This equipment generates or uses radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless
the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if an unauthorized
change or modification is made.
PRECAUTIONS
Please observe the following precautions to prevent
fire, personal injury, and transceiver damage:
•
When operating mobile, do not attempt to configure
your transceiver while driving because it is simply
too dangerous.
•
Be aware of local laws pertaining to the use of
headphones/headsets while driving on public
roads. If in doubt, do not wear headphones while
mobiling.
•
Do not transmit with high output power for
extended periods. The transceiver may overheat.
•
Do not modify this transceiver unless instructed by
this manual or by KENWOOD documentation.
•
Do not expose the transceiver to long periods of
direct sunlight nor place the transceiver close to
heating appliances.
•
Do not place the transceiver in excessively dusty
areas, humid areas, wet areas, nor on unstable
surfaces.
•
If an abnormal odor or smoke is detected coming
from the transceiver, turn OFF the power
immediately. Contact a KENWOOD service station
or your dealer.
•
The transceiver is designed for a 13.8 V power
source. Never use a 24 V battery to power the
transceiver.
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY
THE FCC
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can generate radio frequency
energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that the interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer for technical assistance.
When condensation occurs inside the transceiver:
Condensation possibly occurs inside the transceiver in such a case
where the room is warmed using a heater on cold days or where the
transceiver is quickly moved from a cold room to a warm room. When
condensation occurs, the microcomputer and/or the transmit/receive
circuits may become unstable, resulting in transceiver malfunction. If this
happens, turn OFF the transceiver and just wait for a while. When the
condensed droplets disappear, the transceiver will function normally.
SUPPLIED ACCESSORIES
CONVENTIONS FOLLOWED IN THIS MANUAL
A market code (K, E, or M4) can be found on the label
attached on the package box.
The writing conventions described below have been
followed to simplify instructions and avoid unnecessary
repetition.
Accessory
Microphone
K: MC-53DM
E/ M4: MC-45
DC power cable
Transceiver fuse (15 A)
Front panel mounting bracket
(one pair)
Main-unit mounting bracket
Microphone hanger
(K only)
Screw set for main unit
K1
E/ M4
Screw set for front panel
Modular plug cable
Cushion 2
Warranty card
(U.S.A./ Canada/ Europe only)
Instruction manual
Main
Specialized Communications
Part Number
Quantity
T91-0586-XX
T91-0396-XX
E30-2111-XX
F51-0017-XX
J29-0663-XX
J29-0664-XX
J29-0628-XX
J19-1526-XX
N99-0382-XX
N99-0331-XX
N99-2014-XX
E30-3391-XX
J02-0488-XX
—
B62-1228-XX
B62-XXXXXX
Instruction
What to do
Press [KEY].
Press and release KEY.
Press
[KEY] (1 s).
Press and hold KEY for 1 second or
longer.
Press [KEY1],
[KEY2].
Press KEY1 momentarily, release
KEY1, then press KEY2.
Press [KEY]+
POWER ON.
With transceiver power OFF, press
and hold KEY, then turn ON the
transceiver power by pressing
[PWR].
Press [F] (1 s),
[KEY].
Press and hold [F] for 1 second or
longer, then press KEY.
Press [F], [KEY]
(1 s).
Press [F] momentarily, release [F],
then press and hold KEY for 1
second or longer.
Press [F]+[KEY]. Press and hold [F], then press KEY.
The screw set includes screws for attaching the microphone
hanger {page XX}.
When using the transceiver as a fixed station, you may put
these cushions under the main unit to prevent it from
scratching the desktop.
PREPARATION
MOBILE INSTALLATION
■ Installation Steps
This transceiver asks you to install the front panel and
main unit at separate positions. Select safe, convenient
locations inside your vehicle that minimize danger to
your passengers and yourself while the vehicle is in
motion. For example, consider installing the front panel
under the dash in front of the passenger seat so that
knees or legs will not strike the panel during sudden
braking of your vehicle. Try to pick well-ventilated
locations that are shielded from direct sunlight.
Note: Unlike the previous KENWOOD mobile transceivers, this
transceiver does not allow the front panel and main unit to be joined.
■ Installation Example
MODULAR PLUG CABLE CONNECTION
Use the supplied modular plug cable to connect the front
panel to the main unit.
DC POWER CABLE CONNECTION
■ Mobile Operation
The vehicle battery must have a nominal rating of 12 V.
Never connect the transceiver to a 24 V battery. Be
sure to use a 12 V vehicle battery that has sufficient
current capacity. If the current to the transceiver is
insufficient, the display may darken during transmission,
or transmit output power may drop excessively.
1 Route the DC power cable supplied with the
transceiver directly to the vehicle’s battery
terminals using the shortest path from the
transceiver.
• If using a noise filter, it should be installed with an
insulator to prevent it from touching metal on the
vehicle.
• It is not recommended to use the cigarette lighter
socket since some cigarette lighter sockets introduce
an unacceptable voltage drop.
• If the power cable must be routed through a hole in
the vehicle chassis or body, for example in the
firewall at the front of the passenger compartment,
use a rubber grommet to protect the cable from
abrasion. Dismantle the fuse holder to pass the
cable through the firewall.
2 After the cable is in place, wind heat-resistant tape
around the fuse holder to protect it from moisture.
Tie down the full run of cable.
3 To prevent the risk of short circuits, disconnect
other wiring from the negative (–) battery terminal
before connecting the transceiver.
4 Confirm the correct polarity of the connections,
and attach the power cable to the battery
terminals; red connects to the positive (+)
terminal, black connects to the negative (–)
terminal.
• Use the full length of the cable without cutting off
excess even if the cable is longer than required. In
particular, never remove the fuse holders from the
cable.
Red
Fuse holder
Black
5 Reconnect any wiring removed from the negative
terminal.
6 Connect the DC power cable to the transceiver’s
power supply connector.
• Press the connectors firmly together until the locking
tab clicks.
• The entire length of the cable must be dressed so it
is isolated from heat, moisture, and the engine
secondary (high voltage) ignition system/ cables.
■ Fixed Station Operation
In order to use this transceiver for fixed station
operation, you will need a separate 13.8 V DC power
supply that must be purchased separately. The
recommended current capacity of your power supply
is 12 A.
2 Connect the transceiver’s DC power connector to
the connector on the DC power cable.
• Press the connectors firmly together until the locking
tab clicks.
1 Connect the DC power cable to the regulated DC
power supply and check that polarities are correct
(Red: positive, Black: negative).
• DO NOT directly connect the transceiver to an AC
outlet!
• Use the supplied DC power cable to connect the
transceiver to a regulated power supply.
• Do not substitute a cable with smaller gauge wires.
Fuse holder
Regulated DC power
supply
Red (+)
Black (–)
To AC outlet
Note:
◆ For your transceiver to fully exhibit its performance capabilities,
the following optional power supply is recommended:
PS-33 (20.5 A, 25% duty cycle).
◆ Before connecting the DC power supply to the transceiver, be
sure to switch the transceiver and the DC power supply OFF.
◆ Do not plug the DC power supply into an AC outlet until you
make all connections.
■ Replacing Fuses
ANTENNA CONNECTION
If the fuse blows, determine the cause then correct
the problem. After the problem is resolved, replace
the fuse. If newly installed fuses continue to blow,
disconnect the power cable and contact your dealer
or nearest Service Center for assistance.
Fuse Location
Fuse Current Rating
Transceiver
15 A
Supplied Accessory
DC Power Cable
20 A
Only use fuses of the specified type and rating; otherwise the
transceiver could be damaged.
Note: If you use the transceiver for a long period when the vehicle
battery is not fully charged, or when the engine is OFF, the battery
may become discharged, and will not have sufficient reserves to start
the vehicle. Avoid using the transceiver under these conditions.
Before operating, you must first install an efficient,
well-tuned antenna. The success of your installation will
depend largely on the type of antenna and its correct
installation. The transceiver can give excellent results if
the antenna system and its installation is given careful
attention.
You should choose a 50 Ω impedance antenna to match
the transceiver input impedance. Use low-loss coaxial
feed line that also has a characteristic impedance of
50 Ω. Coupling the antenna to the transceiver via feed
lines having an impedance other than 50 Ω reduces the
efficiency of the antenna system, and can cause
interference to nearby broadcast television receivers,
radio receivers, and other electronic equipment.
◆
◆
Transmitting without first connecting an antenna or other
matched load may damage the transceiver. Always connect the
antenna to the transceiver before transmitting.
All fixed stations should be equipped with a lightning arrester to
reduce the risk of fire, electric shock, and transceiver damage.
ACCESSORY CONNECTIONS
■ External Speakers
If you plan to use external speakers, choose
speakers with an impedance of 8 Ω. The external
speaker jacks accept a 3.5 mm (1/8") mono (2conductor) plug. Recommended speakers include
the SP-50B and SP-41.
■ Microphone
To communicate in the voice modes, connect a 600 Ω
microphone equipped with an 8-pin modular plug into
the modular socket on the front of the main unit.
Press firmly on the plug until the locking tab clicks.
For the U.S.A./ Canada version, a microphone hanger is
supplied. Attach the hanger at an appropriate position
using the screws included in the screw set.
YOUR FIRST QSO
If you tend to discard instruction manuals along with the
packaging material .....please don’t. The 7 steps given here will
get you on the air in your first QSO right away. So, you can enjoy
the exhilaration that comes with opening a brand new
transceiver.
After trying the rig for a while, settle back in your most
comfortable operating chair with this manual and your favorite
drink for an hour or two. The time spent will be worthwhile.
Switch ON the DC power supply, then
press the PWR switch.
Turn the VOL and SQL controls to
approximately 9 o’clock.
Press [BAND SEL] to select the VHF
or UHF band.
Turn the Tuning control to select a
frequency.
Press and hold Mic [PTT], then speak
in a normal tone of voice.
Release Mic [PTT] to receive.
Repeat steps
and
communication.
to continue
GETTING ACQUAINTED
FRONT PANEL
Note: This section describes only the main functions of the front panel
controls and buttons. For the functions not described here, you will find
explanations in the appropriate sections of this manual.
e MRbuotn
Selects the Memory Recall mode {page XX}. In this
mode you can change memory channels, using the
Tuning control or Mic [UP]/ [DWN]. Also starts
Memory Scan {page XX}.
r Tunnigconortl
Selects:
• Operating frequencies when in VFO mode {page XX}.
• Memory channels when in Memory Recall mode
{page XX}.
• Menu Nos. when in Menu mode {page XX}.
q CALLbuotn
Recalls the Call channel {page XX}. Also starts or
stops Call/VFO Scan {page XX} when in VFO mode,
or Call/Memory Scan {page XX} when in Memory
Recall mode.
w VFObuotn
Selects the VFO mode. In this mode you can change
the operating frequency, using the Tuning control or
Mic [UP]/ [DWN]. Also provides:
• VFO Scan start to scan the entire VFO range
{page XX}.
• Program Scan start to scan a programmed range of
frequencies {page XX}.
This control is used for various other selections.
When an up-arrow ( ) and down-arrow ( ) are visible
as button labels, the Tuning control functions in the
exact same way as the up- and down-arrow keys.
t MHzbuotn
Selects the MHz mode. In this mode you can change
the operating frequency in 1 MHz steps or 10 MHz
steps {page XX}, using the Tuning control or Mic
[UP]/ [DWN]. Also starts MHz Scan {page XX}.
!1 CTRLbuotn
Selects the band that you can control using the front
panel buttons or the microphone keys {page XX}.
!2 VOLconrtoslB/ANDSELbuotns
y F(uncoitnb)uotn
Allows you to select the different functions that are
available using the multifunction buttons.
u TONEbuotn
Activates the Tone {page XX}, CTCSS {page XX}, or
DCS function {page XX}.
i REVbuotn
Switches the transmit frequency and receive
frequency when operating with an offset {page XX} or
an odd-split memory channel {page XX}.
o LOWbuotn
Selects High, Medium, or Low transmit output power
{page XX}.
!0 MUTEbuotn
Mutes the speaker allocated to the control band
{page XX}.
When turned, adjusts the level of receive audio from
the speaker {page XX}. Turn the left control (band A)
or the right control (band B) depending on which
band you want to operate.
When pressed, these buttons select the desired TX
band. Press the left button (band A) or the right
button (band B) depending on which band you want
to select.
For band A and B, see page XX.
!3 SQL control
When turned, adjusts the squelch level {page XX}.
This allows you to mute speaker output while no
signals are present.
!4 MNUbuotn
Selects the Menu mode {page XX}.
!5 PMbuotn
Selects the Programmable Memory (PM) mode {page
XX}.
!6 PWRswitch
Switches the transceiver ON or OFF {page XX}.
MAIN UNIT- FRONT
y RESETbuotn
Press momentarily to perform Partial Reset, or press
for 1 second or longer to perform Full Reset {page
XX}. No confirmation message appears. Use this
switch when the microcomputer and/or the memory
chip malfunction because of ambient factors.
MAIN UNIT- REAR
q COMconnector
Accepts a 9-pin female RS-232-C connector for
connecting to a computer {page XX}.
w GPS jack
Accepts a 2.5 mm (1/10") 3-conductor plug for
connecting to a GPS receiver {page XX}.
e DATAconnector
Accepts a 6-pin mini DIN plug for connecting to an
external TNC {page XX}.
r PANELconnecotr
Insert one end of the supplied modular plug cable for
connecting the front panel.
t MC
Iconnecotr
Insert the modular plug on the microphone cable until
the locking tab clicks {page XX}.
q Anetnnaconnecotr
Connect an external antenna {page X}. When making
test transmissions, connect a dummy load in place of
the antenna. The antenna system or load should
have an impedance of 50 Ω. The TM-D700E accepts
a male N-type connector and other versions accept a
male PL-259 connector. This transceiver has only
one antenna connector because of a built-in duplexer.
w PowerInpu1t3.8VDCcable
Connect a 13.8 V DC power source. Use the
supplied DC power cable {pages X and X}.
e Speakeajrcks
10
If you wish, connect an optional external speaker for
clearer audio. These jacks accept a 3.5 mm (1/8")
mono (2-conductor) plug. See page X.
t CALLkey
y VFOkey
u MRkey
MICROPHONE
MC-53DM
MC-45
DWN
Identical to the front panel CALL, VFO and MR
buttons. These keys can be re-programmed, if
desired {page XX}.
UP
7 8
MIC
CALL
VFO
MR
i PFkey
PF
LOCK
ELECTRET CONDENSER MIC
MADE IN JAPAN
q UP
buotn
w DWNbuotn
Raises or lowers the operating frequency, the
memory channel number, the menu number, etc.
Holding either button down causes the action to be
repeated. Also, switches between values for
functions with multiple choices.
Depending on which function you select in Menu 1–
8–1 (PF1) {page XX}, the function of this key differs.
Refer to “PROGRAMMABLE FUNCTION (PF) KEYS”
{page XX}.
o DTMFkeypad(MC-53DMonly)
The 16-key keypad is used for DTMF functions
{page XX}, or to directly enter a frequency or a
memory channel number {page XX}. The keypad is
also available to program a memory channel name
{pages XX and XX}, Power-ON message {page XX},
or other character strings.
e PTP
(Tushosat-w
kl)cthi
Press and hold to transmit, then release to receive.
r LOCKswctih
Locks all microphone keys except [PTT] and (if
equipped) the DTMF keypad.
11
INDICATORS
Ref.
Page
What You
Selected
Locked-out
memory
channel
Speaker Mute
XX
Packet mode
XX
XX
APRS mode
Indicator
On the display you will see various indicators that show
what you have selected.
What You
Selected
Indicator
Tone function
CTCSS
DCS
Plus offset
direction
Minus offset
direction
Minus offset
direction
(–7.6 MHz) 1
Reverse
Automatic
Simplex Check
High transmit
power
Medium
transmit power
Low transmit
power
1 TM-D700E
12
only
What You Press to
Cancel
[TONE], [TONE],
[TONE]
[TONE], [TONE]
[TONE]
[F], [SHIFT], [F],
[SHIFT]
(TM-D700E: one
more [F], [SHIFT])
XX
[F], [SHIFT]
(TM-D700E: one
more [F], [SHIFT])
XX
[F], [SHIFT]
XX
[REV]
XX
[REV]
XX
Default
XX
What You Press to
Cancel
Ref.
Page
Use Menu 1–4–1.
XX
[MUTE]
[F] (1 s), [TNC],
[F] (1 s), [TNC]
XX
[F] (1 s), [TNC]
Narrow transmit
Use Menu 1–3–7.
deviation
XX
XX
XX
XX
For the indicators that will show the current TNC status,
see the table in “OPERATING TNC” {page XX}.
Whenyoureceiveasignal:
• “BUSY” appears when the squelch {page XX} is open.
• The S-meter shows the strength of received signals.
[LOW], [LOW] to
select the default
[LOW] to select
the default
XX
BASIC TRANSCEIVER MODES
This section introduces you to the basic modes you can
select.
VFO mode
Press [VFO] to select. You can change the operating
frequency using the Tuning control or Mic [UP]/ [DWN].
Menu mode
Press [MNU] to select. You can change Menu Nos.
using the Tuning control or [UP]/ [DWN]. Refer to
“MENU SET-UP” {page XX}.
Memory Recall mode
Press [MR] to select. You can change memory
channels, using the Tuning control or Mic [UP]/ [DWN],
where you stored frequencies and related data. Refer to
“MEMORY CHANNELS” {page XX}.
Packet mode
Press [F] (1 s), [TNC] to select. You can send
commands to the built-in TNC from a personal computer.
Refer to “PACKET OPERATION” {page XX}.
Programmable Memory (PM) mode
Press [PM] to select. You can select the transceiver
environment, by pressing [1] to [5], that you stored in
PM channels. Refer to “PROGRAMMABLE MEMORY”
{page XX}.
13
BUTTON FUNCTION DISPLAY
The functions of the 6 buttons below the display can be
identified through the labels shown at the bottom of the
display. After pressing [F] or [F] (1 s), pressing [F]
([OFF]) again restores the basic state.
Note:
◆ When selecting Programmable Memory (PM) mode, you will see
different labels. See “Programmable Memory (PM) mode” {page X}.
◆ You can also select different combinations of buttons labels. See
“CHANGING MULTI-FUNCTION BUTTON LABELS ” {page XX}.
14
The labels of the 5 buttons beside the display are shown
at the left end or right end of the display. These labels
will change depending on the current mode.
BAND A & B
TX BAND AND CONTROL BAND
In this manual, the band recalled at the left hand on the
display is referred to as band A, and the band at the right
hand is called band B. The band A default is VHF (144
MHz) and the band B default is UHF (440 or 430 MHz).
In band A you can also recall a 118 MHz or UHF subband. In band B you can also recall a VHF (144 MHz)
sub-band.
What confuses you on this radio first could be the ideas
of the TX band and Control band. Learn the differences
between these bands.
This transceiver is capable of simultaneously receiving
on 2 bands (A and B). So, for example, it is possible to
receive packet data on one VHF frequency while
receiving audio on another VHF frequency. “ ” indicates
the current data band {page XX}.
TX Band
Press the left [BAND SEL] (band A) or the right [BAND
SEL] (band B) to select. “PTT” on the display shows
which band (A or B) is currently selected as the transmit
(TX) band. You can use the TX band to transmit signals
or to control the transceiver.
Press the left or right [BAND SEL] to select band A or B.
To recall the sub-band, press [F], then the same [BAND
SEL]. The following diagram should help you
understand how to select or recall the desired band.
Control Band
Press [CTRL] to select. On the display “Ctrl” appears to
show which band (A or B) is currently selected as the
Control band. Use this function when you want to
control the band which is not currently used for
transmitting. After selecting the Control band, you
cannot control the TX band.
Note:
◆ You cannot recall a sub-band in Memory Recall mode. First press
[VFO] to select VFO mode.
◆ You cannot recall the UHF sub-band in band A and the VHF subband in band B at the same time.
◆ The 118 MHz band cannot be used for transmitting.
15
MIC KEYPAD DIRECT ENTRY
(U.S.A./ CANADA ONLY)
The keypad on the MC-53DM allows you to make
various entries depending on which mode the
transceiver is in.
In VFO or Memory Recall mode, use the Mic keypad to
select a frequency {page XX} or memory channel
number {page XX}. In Tone or CTCSS freq. Select
mode, use the Mic keypad to select a Tone frequency
{page XX} or CTCSS frequency {page XX}. First press
the Mic PF key programmed as the ENTER key {page
XX}.
To manually send a DTMF number, press and hold Mic
[PTT], then press the DTMF keys on the Mic keypad
{page XX} in sequence.
16
You can also use the Mic keypad to program a memory
channel name {pages XX and XX}, Power-ON message
{page XX}, or other character strings. Each press of a
Mic key switches entry of characters as below:
q z 1 Q Z
m n o 6 M N O
a b c 2 A B C
p r
d e
3 D E F
g h
4 G H I
w x y 9 W X Y
5 J K L
Space
/ & # (
s 7 P R S
u v 8 T U V
) < > ;
OPERATING BASICS
SWITCHING POWER ON/OFF
ADJUSTING VOLUME
1 Switch ON the DC power supply.
Turn the VOL control clockwise to increase the audio
level and counterclockwise to decrease the audio level.
• If operating mobile, skip this step.
2 Press the PWR switch to switch ON the transceiver.
3 To switch OFF the transceiver, press the PWR switch
again.
• If background noise is inaudible because of the Squelch
function, press the Mic PF key assigned the Monitor
function {page XX}, then adjust the VOL control. Press the
PF key again to cancel the Monitor function.
4 If operating as a fixed station, switch OFF the DC
power supply.
SELECTING A BAND
• You may skip step 3. After switching ON the transceiver,
you can switch it OFF or ON using only the power switch
on the DC power supply.
Press the right [BAND SEL] to select band A, or the left
[BAND SEL] to select band B.
• “PTT” moves to the selected band.
• For band A and B, see page XX.
17
SELECTING A FREQUENCY
ADJUSTING SQUELCH
1 Press [VFO] to select VFO mode.
The purpose of the Squelch it to mute the speaker when
no signals are present. With the squelch level correctly
set, you will hear sound only when actually receiving
signals. The higher the squelch level selected, the
stronger the signals must be to receive. The appropriate
squelch level depends on ambient noise conditions.
2 To increase the frequency, turn the Tuning control
clockwise or press Mic [UP].
To decrease the frequency, turn the Tuning control
counterclockwise or press Mic [DWN].
The current squelch level is incorrect.
• Pressing and holding Mic [UP]/ [DWN] causes the
frequency to step repeatedly.
• To change frequencies in steps of 1 MHz, press [MHz]
first. Pressing [MHz] again cancels this function.
• To change frequencies in steps of 10 MHz, press
[F]+[MHz] first; do not press [F] for longer than
1 second. Pressing [F] cancels the 10 MHz function;
pressing [MHz] starts the 1 MHz function.
You can also select frequencies via the microphone
keypad. See “DIRECT FREQUENCY ENTRY” {page
XX}.
The current squelch level is correct.
18
Turn the SQL control when no signals are present.
Select the squelch level at which the background noise
is just eliminated.
TRANSMITTING
1 To transmit, press and hold Mic [PTT] and speak into
the microphone in a normal tone of voice.
• “ON AIR” and the RF power meter appear.
■ Selecting Output Power
It’s wise to select lower transmit power if
communication is still reliable. This lowers the risk of
interfering with others on the band. When operating
from battery power, you will enjoy more operating
time before a charge is necessary.
Press [LOW] to select high (“H”), medium (“M”), or
low (“L”) power. The default is high.
• You can program a different power for band A and B.
• Speaking too close to the microphone, or too loudly,
may increase distortion and reduce intelligibility of your
signals at the receiving station.
• The RF power meter shows the relative transmit output
power.
2 When you finish speaking, release Mic [PTT].
Time-Out Timer: Holding down Mic [PTT] for more than 10 minutes
causes the transceiver to generate a beep and stop transmitting.
Release, then press Mic [PTT] to resume transmitting. You may change
the time-out time to 3 or 5 minutes {page XX}.
◆
◆
Do not transmit at high output power for an extended period of
time. The transceiver could overheat and malfunction.
Continuous transmission causes the heat sink to overheat.
Never touch the heat sink when it may be hot.
Note: When the transceiver overheats because of ambient high
temperature or continuous transmission, the protective circuit may
function to lower transmit output power.
19
MENU SET-UP
The Menu system on this transceiver consists of 3
levels.
3 Press [OK].
• The current level 2 No. blinks.
4 Press [UP]/ [DWN] to select the appropriate level
2 No.
MENU ACCESS
1 Press [MNU] to enter Menu mode.
• The current level 1 No. blinks.
• To move back to level 1, press [BACK] instead.
• To exit Menu mode, press [ESC].
5 Press [OK].
6 For Menu 1–1 to 1–9 and 1–A, repeat steps 4 and
5 to select level 3.
7 Press [UP]/ [DWN] to select a parameter.
2 Press [UP]/ [DWN] to select the appropriate level 1
No.
• The procedure in this step differs depending on
which menu item you selected. See the appropriate
sections in this manual.
8 Press [OK] to complete the setting.
9 Press [MENU] to exit Menu mode.
20
MENU CONFIGURATION
The shaded Menu Nos. are described in the separate manual, “SPECIALIZED COMMUNICATIONS”.
Level 1
Level 2
1 DISPLAY
2 AUDIO
1 RADIO
3 TX/RX
HELLO !!
Ref.
page
XX
Level 8
XX
Positive/ Negative
Negative
XX
4 Auto Dimmer Change
ON/ OFF
XX
5 Multi-function button
Mode 1/ 2/ 3
OFF
Mode 1
XX
1 Beep volume
Level 1 (min.) ~ 7 (max.)/
OFF
Level 5
XX
2 Key Beep
ON/ OFF
ON
XX
3 Speaker configuration
Voice Synthesizer
4 (With the optional VS-3
installed)
1 Programmable VFO
Mode 1/ 2
Mode 1
XX
English/ Japanese/ OFF
English
XX
—
XX
2 S-meter Squelch
ON/ OFF
OFF
XX
3 Squelch hang time
125 / 250 / 500 msec./ OFF
OFF
XX
Level 3
Selections
1 Power-ON Message
See reference page.
2 Contrast
Level 1 (min.) ~ 16 (max.)
3 Reverse mode
See reference page.
4 FM/ AM mode
FM/ AM
5 Advanced Intercept Point
ON/ OFF
6 Beat Shift
7 TX deviation
Default
See reference
page.
XX
OFF
XX
Normal/ Upper
Normal
XX
Wide/ Narrow
Wide
XX
21
Level 1
Level 2
4 MEMORY
5 DTMF
Level 3
XX
—
XX
See reference page.
3 Auto PM Channel Store
ON/ OFF
OFF
XX
4 Channel Display
ON/ OFF
OFF
XX
1 Number Store
See reference page.
—
XX
2 TX speed
Fast/ Slow
Fast
XX
3 TX Hold
ON/ OFF
100/ 250/ 500/ 750/ 1000/
1500/ 2000 msec.
See reference page.
OFF
XX
500 msec.
XX
Band B
(XX)
(XX)
4 Time
1200/ 9600 bps
1200 bps
A & B bands/ Data or Data Data or Data
TX band
TX band
See reference page.
—
5 Date
See reference page.
—
(XX)
6 Time zone
—
(XX)
2 Automatic Repeater Offset
See reference page.
00.00 ~ 29.95 MHz in steps
of 50 kHz
ON/ OFF
3 Call Button Function
3 DCD sense
1 Offset frequency
22
OFF
2 Memory channel name
2 Packet transfer rate
7 REPEATER
Ref. page
ON/ OFF
1 Data band
6 TNC
Default
1 Memory Channel Lockout
4 Pause
1 RADIO
Selections
See reference
page.
(XX)
(XX)
XX
ON
XX
Call/ 1750 Hz TX
Call
XX
4 TX Hold
ON/ OFF
OFF
XX
5 Repeater Hold
ON/ OFF
OFF
XX
6 Repeater function
ON/ OFF
OFF
XX
Level 1
Level 2
MIC
RADIO
AUX
REMOTE
CON
Level 3
Selections
Default
Ref.
page
Mic PF Key
See reference page.
PF
XX
Mic MR Key
See reference page.
MR
XX
Mic VFO Key
See reference page.
VFO
XX
Mic CALL Key
See reference page.
CALL
XX
Microphone Control
ON/ OFF
OFF
XX
DTMF Monitor
ON/ OFF
OFF
XX
Scan Resume
Time-Operated/ CarrierOperated/ Seek
TimeOperated
XX
Number of Channels for
Visual Scan
31/ 61/ 91/ 181
61
XX
Automatic Power Off (APO) ON/ OFF
OFF
XX
Time-Out Timer (TOT)
3/ 5/ 10 minutes
10 minutes
XX
COM port
9600/ 19200/ 38400/
57600 bps
9600 bps
(XX)
Data port
1200/ 9600 bps
1200 bps
(XX)
Reset
See reference page.
—
XX
Secret code
See reference page.
—
XX
Acknowledgement
ON/ OFF
OFF
XX
Remote Control
ON/ OFF
OFF
XX
23
—
Ref.
page
(XX)
White
(XX)
—
(XX)
White
(XX)
—
(XX)
White
(XX)
See reference page.
—
(XX)
8 SSTV mode
See reference page.
—
(XX)
9 VC-H1 Control
ON/ OFF
OFF
(XX)
1 My call sign
See reference page.
—
(XX)
2 GPS receiver
Not used/ NMEA/ NMEA96
Not used
(XX)
3 Waypoint
See reference page.
—
(XX)
4 My position
See reference page.
—
(XX)
5 Position Ambiguity
1/ 2/ 3/ 4 digits/ OFF
OFF
(XX)
6 Position comment
—
(XX)
OFF
(XX)
8 Station icon
See reference page.
10 ~ 2500 in steps of
10/ OFF
See reference page.
—
(XX)
9 Status text
See reference page.
—
(XX)
Level 1
2 SSTV
3 APRS
Level 2
1 My call sign
See reference page.
2 Color for call sign
White/ Black/ Blue/ Red/
Magenta/ Green/ Cyan/ Yellow
3 Message
See reference page.
4 Color for message
White/ Black/ Blue/ Red/
Magenta/ Green/ Cyan/ Yellow
5 RSV report
See reference page.
6 Color for RSV report
White/ Black/ Blue/ Red/
Magenta/ Green/ Cyan/ Yellow
7 Superimposition Execute
7 Reception restriction distance
24
Selections
Default
A Status text transmit rate
See reference page.
—
Ref.
page
(XX)
B Packet path
See reference page.
—
(XX)
C Packet transmit method
Manual
(XX)
5 minutes
(XX)
E Group code
Manual/ PTT/ Auto
.5/ 1/ 2/ 3/ 5/ 10/ 20/ 30
minutes
See reference page.
—
(XX)
F Beep
Mine/ All new/ All/ OFF
All
(XX)
G Unit for distance
Mile/ Kilometer
Kilometer 1
(XX)
H Unit for temperature
°F/ °C
°C 1
(XX)
Data band
See reference page.
Band A
(XX)
Packet transfer rate
1200/ 9600 bps
1200 bps
(XX)
OFF
(XX)
—
(XX)
OFF
(XX)
Level 1
Level 2
D Packet transmit interval
3 APRS
Selections
Default
K Digipeater
ON/ OFF
L Digipeating path
See reference page.
M Auto Message Reply
ON/ OFF
N Reply message
See reference page.
—
(XX)
O Bulletin group
See reference page.
—
(XX)
P Message group
See reference page.
—
(XX)
SKY
CMD
1 Commander call sign
See reference page.
—
XX
2 Transporter call sign
See reference page.
—
XX
(U.S.A./
Canada)
3 Tone frequency
See reference page.
—
XX
4 Sky Command mode
Commander/ Transporter/ OFF
OFF
XX
U.S.A./ Canada: Mile and °F
25
OPERATING THROUGH REPEATERS
Repeaters, which are often installed and maintained by
radio clubs, are usually located on mountain tops or
other elevated locations. Generally they operate at
higher ERP (Effective Radiated Power) than a typical
station. This combination of elevation and high ERP
allows communications over much greater distances
than communications without using repeaters.
Most repeaters use a receive and transmit frequency
pair with a standard or non-standard offset (odd-split). In
addition, some repeaters must receive a tone from the
transceiver to allow it to access. For details, consult
your local repeater reference.
Offset Programming Flow
q Select a band.
w Select a receive frequency.
e Select an offset direction.
r Select an offset frequency.
(Only when programming odd-split
repeater frequencies)
t Activate the Tone function.
(If necessary)
y Select a tone frequency.
(If necessary)
If you store the above data in a memory channel, you
need not reprogram every time. See “MEMORY
CHANNELS” {page XX}.
26
PROGRAMMING OFFSET
First select band A or B by pressing the left or right
[BAND SEL]. To recall the sub-band next, press [F],
then the same [BAND SEL].
■ Selecting Offset Direction
Select whether the transmit frequency will be higher
(+) or lower (–) than the receive frequency.
Press [F], [SHIFT] to switch the offset direction.
• “+” or “–” appears to indicate which offset direction is
selected.
■ Selecting Offset Frequency
To access a repeater which requires an odd-split
frequency pair, change the offset frequency from the
default which is used by most repeaters. The default
offset frequency on the VHF band is 600 kHz no
matter which market version; the default on the UHF
band is 5 MHz (TM-D700A) or 1.6 MHz (TM-D700E).
1 Press [MNU] to enter Menu mode.
2 Press [UP]/ [DWN] to select “RADIO (1–)”, then
press [OK].
3 Press [UP]/ [DWN] to select “REPEATER (1–7–)”,
then press [OK].
4 Press [UP]/ [DWN] to select “OFFSET
FREQUENCY (1–7–1)”, then press [OK].
• To program –7.6 MHz offset on the TM-D700E (UHF
only), repeatedly press [F], [SHIFT] until “=” appears.
If the offset transmit frequency falls outside the
allowable range, transmitting is inhibited. Use one of
the following methods to bring the transmit frequency
within the band limits:
• Move the receive frequency further inside the band.
• Change the offset direction.
Note: While using an odd-split memory channel or transmitting, you
cannot change the offset direction.
5 Press [UP]/ [DWN] to select the appropriate offset
frequency.
• The selectable range is from 0.00 MHz to 29.95 MHz
in steps of 50 kHz.
6 Press [OK] to complete the setting.
7 Press [MNU] to exit Menu mode.
TM-D700E Only: If you have selected “ =” for the offset direction,
you cannot change the default (7.6 MHz).
Note: After changing the offset frequency, the new offset frequency
will also be used by Automatic Repeater Offset.
27
■ Activating Tone Function
Press [TONE] to activate the Tone function.
2 Press [UP]/ [DWN] to select the appropriate tone
frequency.
• “T” appears when the Tone function is ON.
3 Press [OK] to complete the setting.
• Each press of [TONE] changes the selection as Tone –>
CTCSS –> DCS –> No selection.
No.
Freq.
(Hz)
No.
Freq.
(Hz)
No.
Freq.
(Hz)
No.
Freq.
(Hz)
Note:
◆ You cannot use the Tone function with the CTCSS or DCS
function.
◆ You need to activate the Tone function only when selecting one
of the 38 standard frequencies. The selection you make here will
not affect transmission of a 1750 Hz tone.
01
67.0
11
97.4
21
136.5
31
192.8
02
71.9
12
100.0
22
141.3
32
203.5
03
74.4
13
103.5
23
146.2
33
210.7
04
77.0
14
107.2
24
151.4
34
218.1
05
79.7
15
110.9
25
156.7
35
225.7
Note: The procedures for transmitting a 1750 Hz tone are described
on page XX.
06
82.5
16
114.8
26
162.2
36
233.6
1 Press [F], [T.SEL].
07
85.4
17
118.8
27
167.9
37
241.8
08
88.5
18
123.0
28
173.8
38
250.3
09
91.5
19
127.3
29
179.9
10
94.8
20
131.8
30
186.2
■ Selecting a Tone Frequency
• The current tone frequency appears and blinks. The
default is 88.5 Hz.
After programming one of the Mic PF keys as the
ENTER key {page XX}, you can also select a tone
frequency by direct entry from the Mic keypad. In
step 2, press [ENTER], then enter 01 to 38 shown in
the table. To select 100 Hz, for example, press
[ENTER], [0], [1], [2].
28
AUTOMATIC REPEATER OFFSET
1 Press [MNU] to enter Menu mode.
This function automatically selects an offset direction,
according to the frequency that you select on the VHF
band. The transceiver is programmed for offset direction
as shown below. To obtain an up-to-date band plan for
repeater offset direction, contact your national Amateur
Radio association.
2 Press [UP]/ [DWN] to select “RADIO (1–)”, then
press [OK].
U.S.A. and Canada versions
3 Press [UP]/ [DWN] to select “REPEATER (1–7–)”,
then press [OK].
4 Press [UP]/ [DWN] to select “AUTO OFFSET (1–7–
2)”, then press [OK].
This complies with the standard ARRL band plan.
144.0
145.5
146.4
147.0
147.6
145.1
146.0
146.6
147.4
148.0 MHz
−
−
−
5 Press [UP]/ [DWN] to switch the function ON
(default) or OFF.
S: Simplex
European versions
6 Press [OK] to complete the setting.
144.0
145.6 145.8 146.0 MHz
–
7 Press [MNU] to exit Menu mode.
S: Simplex
Note: Automatic Repeater Offset does not function when Reverse is ON.
However, pressing [REV] after Automatic Repeater Offset has selected
an offset (split) status, exchanges the receive and transmit frequencies.
29
TRANSMITTING A 1750 Hz TONE
Most of the repeaters in Europe require that a
transceiver transmit a 1750 Hz tone. On a TM-D700E,
simply pressing Mic [CALL] causes it to transmit a 1750
Hz tone. It is also possible to program [CALL] on the
front panel as a button for transmitting a 1750 Hz tone.
1 Press [MNU] to enter Menu mode.
2 Press [UP]/ [DWN] to select “RADIO (1–)”, then
press [OK].
3 Press [UP]/ [DWN] to select “REPEATER (1–7–)”,
then press [OK].
Some repeaters in Europe must receive continuous
signals for a certain period of time, following a 1750 Hz
tone. This transceiver is also capable of remaining in the
transmit mode for 2 seconds after transmitting a 1750 Hz
tone.
1 Press [MNU] to enter Menu mode.
2 Press [UP]/ [DWN] to select “RADIO (1–)”, then
press [OK].
3 Press [UP]/ [DWN] to select “REPEATER (1–7–)”,
then press [OK].
4 Press [UP]/ [DWN] to select “TX HOLD (1–7–4)”,
then press [OK].
4 Press [UP]/ [DWN] to select “1750Hz TONE (1–7–
3)”, then press [OK].
5 Press [UP]/ [DWN] to switch the function ON (or
OFF).
5 Press [UP]/ [DWN] to select “1750 Hz”.
6 Press [OK] to complete the setting.
7 Press [MNU] to exit Menu mode.
• “1750” appears in place of “CALL” as the button label.
Note:
◆ All market versions allow the above selection in Menu 1–7–3.
◆ All market versions allow any Mic PF key to be assigned the 1750 Hz
Tone function {page XX}.
◆ The transceiver continuously transmits a 1750 Hz tone until you
release Mic [CALL], or [CALL].
30
6 Press [OK] to complete the setting.
7 Press [MNU] to exit Menu mode.
Note:
◆ All market versions allow the above selection in Menu 1–7–4.
◆ While remaining in the transmit mode, the transceiver does not
continuously transmit a 1750 Hz tone.
REVERSE FUNCTION
AUTOMATIC SIMPLEX CHECK (ASC)
The reverse function exchanges a separate receive and
transmit frequency. So, while using a repeater, you can
manually check the strength of a signal that you receive
directly from the other station. If the station’s signal is
strong, both stations should move to a simplex frequency
and free up the repeater.
While using a repeater, ASC periodically monitors the
strength of a signal that you receive directly from the
other station. If the station’s signal is strong enough to
allow direct contact without a repeater, the ASC indicator
on the display begins blinking.
Press [REV] (1 s) to switch the function ON.
• The ASC indicator appears when the function is ON.
• While direct contact is possible, the ASC indicator blinks.
Press [REV] to switch the Reverse function ON (or
OFF).
•
“R” appears when the function is ON.
Note:
◆ If pressing [REV] places the transmit frequency outside the allowable
range, then pressing Mic [PTT] causes an error beep to sound;
transmission is inhibited.
◆ If pressing [REV] places the receive frequency outside the allowable
range, an error beep sounds and no reversal occurs.
◆ Automatic Repeater Offset does not function while Reverse is ON.
◆ You cannot switch Reverse ON or OFF while transmitting.
• To quit the function, press [REV].
Note:
◆ Pressing Mic [PTT] causes the ASC indicator to quit blinking.
◆ ASC does not function if your transmit and receive frequencies are
the same (simplex operation).
◆ ASC does not function while scanning.
◆ Activating ASC while using Reverse switches Reverse OFF.
◆ If you recall a memory channel or the Call channel that contains
Reverse ON status, ASC is switched OFF.
◆ ASC causes receive audio to be momentarily intermitted every 3
seconds.
31
TONE FREQ. ID
This function scans through all tone frequencies to
identify the incoming tone frequency on a received
signal. You may use the function to find which tone
frequency is required by your local repeater.
1 Press [TONE] to switch ON the Tone function.
• “T” appears when the Tone function is ON.
2 Press [F], [T.SEL].
• The current tone frequency appears and blinks.
3 Press [SCAN] to activate the Tone Freq. ID.
“T SCAN” appears.
• To reverse the scan direction, turn the Tuning control
clockwise (upward scan) or counterclockwise
(downward scan). You can also press Mic [UP]/ [DWN].
• To quit the function, press [ESC].
• When the tone frequency is identified, the identified
frequency appears and blinks.
32
2 Press [OK] to program the identified frequency in
place of the currently set tone frequency.
• The previous frequency display is restored with the Tone
function remained ON. You may press [TONE] to switch
the Tone function OFF.
• Press [ESC] if you do not want to program the identified
frequency.
• Press [SCAN] while the identified frequency is blinking,
to resume scanning.
MEMORY CHANNELS
In memory channels, you can store frequencies and
related data that you often use. Then you need not
reprogram those data every time. You can quickly recall
a programmed channel by simple operation. A total of
200 memory channels are available for bands A and B.
The data listed below can be stored in each memory
channel:
Parameter
Receive frequency
SIMPLEX & REPEATER OR ODD-SPLIT MEMORY
CHANNEL?
Transmit frequency
Simplex &
Repeater
Yes
Odd-split
Yes
Yes
Tone frequency
Yes
Yes
Tone ON
Yes
Yes
CTCSS frequency
Yes
Yes
You can use each memory channel as a simplex &
repeater channel or odd-split channel. Store only one
frequency to use as a simplex & repeater channel or two
separate frequencies to use as an odd-split channel.
Select either application for each channel depending on
the operations you have in mind.
CTCSS ON
Yes
Yes
DCS code
Yes
Yes
Simplex & repeater channel allows:
DCS ON
Yes
Yes
• Simplex frequency operation
Offset direction
Yes
N/A
• Repeater operation with a standard offset
(If an offset direction is stored)
Offset frequency
Yes
N/A
Reverse ON
Yes
N/A
Frequency step size
Yes
Yes
Memory channel lockout
Yes
Yes
Memory channel name
Yes
Yes
FM/ AM mode selection
Yes
Yes
Odd-split channel allows:
• Repeater operation with a non-standard offset
Note:
◆ Not only can you store data in memory channels, but you can also
overwrite existing data with new data.
◆ If you have recalled a memory channel on the non-control band
(A or B), you cannot select the same channel on the control band to
program data.
Yes: Can be stored in memory.
N/A: Cannot be stored in memory.
33
STORING SIMPLEX FREQUENCIES OR STANDARD
REPEATER FREQUENCIES
1 Select the desired band.
2 Press [VFO].
3 Select the desired frequency.
4 If storing a standard repeater frequency, select the
following data:
• Offset direction {page XX}
• Tone ON, if necessary {page XX}
• Tone frequency, if necessary {page XX}
STORING ODD-SPLIT REPEATER FREQUENCIES
Some repeaters use a receive and transmit frequency
pair with a non-standard offset. If you store two separate
frequencies in a memory channel, you can operate on
those repeaters without programming the offset
frequency and direction.
1 Select the desired receive frequency and related data
by using steps 1 to 4 given for simplex or standard
repeater frequencies.
2 Press [F].
If storing a simplex frequency, you may select other
related data (CTCSS ON, CTCSS freq., etc.).
5 Press [F].
3 Turn the Tuning control, or press Mic [UP]/ [DWN], to
select the desired memory channel.
4 Press [M.IN] (1 s).
• “±” appears and the receive frequency blinks.
• A memory channel number appears and blinks.
• “ ” indicates the current channel is empty; “
instead, if the channel contains data.
” appears
5 Select the desired transmit frequency (within
approx.10 seconds).
6 Turn the Tuning control, or press Mic [UP]/ [DWN], to
select the desired memory channel.
7 Press [M.IN].
34
6 Press [M.IN].
Note:
◆ When you recall an odd-split memory channel, “±” appears on the
display. To confirm the transmit frequency, press [REV].
◆ Transmit Offset status and Reverse status are not stored in an oddsplit memory channel.
RECALLING A MEMORY CHANNEL
CLEARING A MEMORY CHANNEL
1 Select the desired band.
Use the following procedure to clear an individual
memory channel. Full Reset {page XX} is a quick way to
clear all memory channels.
2 Press [MR] to enter Memory Recall mode.
• The memory channel used last is recalled.
1 Recall the desired memory channel.
2 Switch OFF the power to the transceiver.
3 Press [MHz]+ POWER ON.
• A confirmation message appears.
3 Turn the Tuning control, or press [UP]/ [DWN], to
select the desired memory channel.
• You cannot recall an empty memory channel.
• To restore VFO mode, press [VFO].
After programming one of the Mic PF keys as the
ENTER key {page XX}, you can also recall a memory
channel by direct entry from the Mic keypad. In Memory
Recall mode press [ENTER], then enter the channel
number. To recall channel 3, for example, press
[ENTER], [0], [0], [3].
Note:
◆ When you recall an odd-split memory channel, “±” appears on the
display. Press [REV] to display the transmit frequency.
◆ After recalling a memory channel, you may program data such as
Tone or CTCSS. These settings, however, are cleared once you
select another channel or the VFO mode. To permanently store the
data, overwrite the channel contents {page XX}.
• To quit clearing the memory channel, press [ESC].
4 Press [OK].
Note:
◆ If you have recalled a memory channel on the non-control band (A or
B), you cannot select the same channel on the control band to clear.
◆ When in Channel Display mode, you cannot clear any memory
channel.
35
NAMING A MEMORY CHANNEL
You can name memory channels using up to 8
alphanumeric characters. When you recall a named
memory channel, its name appears on the display
instead of the stored frequency. Names can be call
signs, repeater names, cities, names of people, etc.
1 Recall the desired memory channel.
2 Press [MNU] to enter Menu mode.
3 Press [UP]/ [DWN] to select “RADIO (1–)”, then
press [OK].
4 Press [UP]/ [DWN] to select “MEMORY (1–4–)”, then
press [OK].
8 Repeat steps 6 and 7 to enter up to 8 digits.
Switches among the sets of alphanumeric
CHAR characters, accented letters (TM-D700E only),
and special ASCII characters.
Switches between
Cancels Memory
a/A small and capital
BACK Name Entry.
letters.
Deletes the digit at
Causes the cursor
DEL which the cursor is
].
• The cursor moves to the next digit.
36
CALL CHANNEL
The Call channel can always be selected quickly no
matter what mode the transceiver is in. For instance,
you may use the Call channel as an emergency
channel within your group. In this case, the Call/VFO
scan {page XX} will be useful.
The default frequency stored in the Call channel is
144.000 MHz for the VHF band. The default on the UHF
band is 440.000 MHz or 430.000 MHz depending on the
market versions. The Call channel can be
reprogrammed either as a simplex & repeater or oddsplit channel.
Note: Unlike channels 1 to 200 the call channel cannot be cleared.
■ Recalling the Call Channel
1 Select the desired band.
2 Press [CALL] to recall the Call channel.
• “CALL” appears.
■ Reprogramming the Call Channel
1 Select the desired band.
2 Press [VFO].
3 Select the desired frequency and related data
(Tone, CTCSS, etc.).
• When you program the Call channel as an odd-split
channel, select a receive frequency.
4 Press [F], [C.IN].
• The selected frequency and related data are stored
in the Call channel.
• The previous mode is restored.
• When programming as an odd-split channel, press
[F], [C.IN] (1 s) instead; “±” appears.
To also store a transmit frequency, proceed to the
next step.
5 Select the desired transmit frequency.
6 Press [C.IN].
• The transmit frequency is stored in the Call channel,
and the previous mode is restored.
• To restore the previous mode, press [CALL] again.
Note:
◆ Transmit Offset status and Reverse status are not stored in an
odd-split Call channel.
◆ To store data other than frequencies, select the data in step 3 not
step 5.
37
MEMORY-TO-VFO TRANSFER
CHANNEL DISPLAY
You may sometimes want to search for other stations or
a clear frequency, near the frequency stored in a
memory channel or the Call channel. In this case first
transfer the contents of a memory channel or the Call
channel to the VFO.
When in this mode, the transceiver displays only
memory channel numbers (or memory names if stored)
instead of frequencies.
1 Recall the desired memory channel or the Call
channel.
2 Press [F], [M>V].
1 Press [MNU] to enter Menu mode.
2 Press [UP]/ [DWN] to select “RADIO (1–)”, then
press [OK].
3 Press [UP]/ [DWN] to select “MEMORY (1–4–)”, then
press [OK].
4 Press [UP]/ [DWN] to select “CHANNEL DISPLAY
(1–4–4)”, then press [OK].
• The entire contents of the memory channel or the Call
channel are copied to the VFO.
Note:
◆ A transmit frequency from an odd-split memory channel or odd-split
Call channel is not transferred to the VFO. To transfer a transmit
frequency, press [REV], then press [F], [M>V].
◆ Lockout status and memory names are not copied from a memory
channel to the VFO.
◆ If you recall the Call channel in step 1, simply turning the Tuning
Control or pressing Mic [UP]/ [DWN] also transfers the contents to
the VFO. The frequency, however, is changed by one step.
5 Press [UP]/ [DWN] to switch the function ON (or
OFF).
6 Press [OK] to complete the setting.
7 Press [MNU] to exit Menu mode.
Note: You cannot switch this function ON if you have not used both
bands A and B to store frequencies.
When in Channel Display mode, you cannot use the
following functions:
Sub-band Select
Memory Store
Memory-to-VFO
Transfer
All-control Lock
38
VFO Select
PM Store
VFO Scan
PM Recall
utomatic Simplex
Partial/ Full/ PM Reset A
Check
Display Demonstration
PARTIAL OR FULL RESET?
1 Press [MNU] to enter Menu mode.
If your transceiver seems to be malfunctioning,
initializing the transceiver may resolve the problem. Use
Full Reset to initialize all settings that you have
customized. Partial (VFO) Reset does not initialize the
following settings:
2 Press [UP]/ [DWN] to select “RADIO (1–)”, then
press [OK].
Memory channels
Call channels
Program scan channels
PM channels
3 Press [UP]/ [DWN] to select “AUX (1–9–)”, then
press [OK].
4 Press [UP]/ [DWN] to select “RESET (1–9–7)”, then
press [OK].
Memory channel lockout
Some of the VFO factory defaults are listed below:
Parameter
Band A
Band B
5 Press [UP]/ [DWN] to select Partial (VFO) Reset, PM
Reset {page XX}, or Full Reset, then press [OK].
• A confirmation message appears.
6 Press [OK].
VFO freq.
144.000 MHz
440.000 MHz
(U.S.A./ Canada) or
430.000 MHz
Freq. step:
12.5 kHz (U.S.A./
Canada) or 5 kHz
25 kHz
Tone freq.:
88.5 Hz
88.5 Hz
After switching the power OFF, you may press [VFO]+
POWER ON for Partial Reset, or [MR]+ POWER ON for
Full Reset. This allows you to skip steps 1 to 5.
You can also use the RESET button to perform Partial or
Full Reset. See page XX.
Note: When in All-control Lock or Channel Display mode, you cannot
perform Partial Reset nor Full Reset.
39
PROGRAMMABLE MEMORY (PM)
Programmable Memory (PM) stores virtually all settings
currently set on the transceiver. This transceiver
provides 5 PM channels to store 5 sets of transceiver
configurations. Later you can quickly recall one of these,
depending on operation in your mind or the environment.
PROGRAMMABLE INFORMATION
The following settings can be separately stored for band
A and B:
The following settings are shared by both band A and B:
TX band
Control band
Transmit output power
Time-Out Timer
Automatic Repeater Offset
Transmit Hold, 1750 Hz
tone
Display Dimmer
Auto Dimmer Change
Display contrast
Positive/ Negative
Reversal
VFO frequency
VFO mode
Auto Band Change
S-meter Squelch
Memory Recall mode
Call Channel mode
Beep volume
Automatic Power Off
Offset direction
Offset frequency
Advanced Intercept Point
Beat Shift
Reverse ON
Automatic Simplex Check
Scan resume method
Tone ON
Tone frequency
Microphone keypad
confirmation tone
CTCSS ON
CTCSS frequency
Data band
Data transfer rate
DCS ON
DCS code
Upper frequency limit
(for Programmable VFO)
Lower frequency limit
(for Programmable VFO)
Frequency step size
FM/ AM mode
40
APPLICATION EXAMPLES
The following are examples of how you might use Programmable Memory. These examples may not represent
applications useful to you, but you will understand the flexibility of this function.
Situation 1
Solution
Solution
You share your transceiver with other members in
your family or club. However, each individual has
personal preferences for how they like to set various
functions. You have to keep changing many settings
each time you use the transceiver.
Because 5 PM channels are available, up to 5
persons can separately program the transceiver and
store their customized environment. Then each
person can quickly change to his or her favorite
settings, simply by recalling a PM channel.
It is too much trouble to change back the settings
after somebody else has reconfigured them. So this
application may avoid having a feature-rich
transceiver but never using many useful features.
Situation 2
While operating mobile on the way to work every
morning, you prefer a silent transceiver that does not
interrupt the morning calm. In addition, you feel that a
bright display is a waste of electricity in sunlight.
At night when driving home, you realize the Beep
function truly serves a purpose and you acknowledge
it is nice to see a bright display after dark.
Solution
Solution
In two PM channels, store the same operating data
such as frequency, offset, tone, etc., and store
different settings for the Display Dimmer and Beep
functions. Then you can quickly recall the best
settings for day or night operating.
Situation 3
You cannot figure out how you can make the
transceiver exit the current mode.
Solution
Solution
Simply recall PM channel 1 that contains an exact
copy of the transceiver default environment except for
the display illumination level. You will not lose the
contents of any memory channels.
41
STORING IN PM CHANNELS
RECALLING A PM CHANNEL
1 Confirm that the following conditions have been
satisfied:
1 Press [PM].
• The transceiver is in the receive mode.
• Scan is not being used.
• Microphone Control is OFF.
• The PM channel numbers 1 to 5 appear at the bottom of
the display.
• The current PM channel number appears and blinks at
the upper right corner.
2 Select the desired band.
3 Select the desired frequency and related data (Tone,
CTCSS, etc.) using VFO mode.
4 If required, select another band, then select the
desired frequency and related data.
5 Press [F], [P.IN].
• The PM channel numbers appear and blink.
• If in Auto PM Store mode {page XX}, the current PM
channel number appears with “>”; ex. >PM1.
2 Press [1] to [5] corresponding to the desired PM
channel.
• The contents of the selected channel are recalled.
6 Press [1] to [5] corresponding to the desired PM
channel.
• The selected frequency and related data are stored in
the PM channel.
42
• Press [OFF] to exit PM Recall mode,
Note: You cannot recall a PM channel while transmitting.
AUTO PM CHANNEL STORE
PM CHANNEL RESET
After you recalled a PM channel, this function
automatically overwrites the current PM channel with the
present operating environment when:
If you want to reprogram the PM channels from the
beginning, reset all the PM channels to the factory
defaults.
• You recall another PM channel.
1 Press [CALL]+ POWER ON.
• You press [OFF].
• A confirmation message appears.
• You switch OFF the transceiver.
The factory default of this function is ON.
1 Press [MNU] to enter Menu mode.
2 Press [UP]/ [DWN] to select “RADIO (1–)”, then
press [OK].
• Press [ESC] to quit resetting.
3 Press [UP]/ [DWN] to select “MEMORY (1–4–)”, then
press [OK].
2 Press [OK].
4 Press [UP]/ [DWN] to select “AUTO PM STORE (1–
4–3)”, then press [OK].
You can also use Menu 1–9–7 (RESET) to reset the PM
channels. See XX.
5 Press [UP]/ [DWN] to switch the function ON
(default) or OFF.
6 Press [OK] to complete the setting.
7 Press [MNU] to exit Menu mode.
43
SCAN
Scan is a useful feature for hands-off monitoring of your
favorite frequencies. Becoming comfortable with all
types of Scan will increase your operating efficiency.
This transceiver provides the following types of scans
plus Visual Scan {page XX}. Visual Scan graphically
and simultaneously shows how frequencies in a specific
range are busy.
Scan Type
VFO Scan
Memory Scan
Group Scan
Program Scan
MHz Scan
Call/VFO Scan
Call/Memory Scan
Scan Range
All frequencies tunable on the
band
Frequencies stored in the memory
channels
Frequencies stored in the memory
channels which belong to the
specified group
All frequencies in the range
selected on the band
All frequencies within a 1 MHz
range
Call channel plus the current VFO
frequency
Call channel plus the selected
memory channel
Note:
◆ Adjust the squelch level before using Scan. Selecting a squelch level
too low could cause Scan to stop immediately.
◆ While using CTCSS or DCS, Scan stops for any signal received;
however, you will hear audio only when the signal contains the same
CTCSS tone or DCS code that you selected.
◆ When using S-meter Squelch, Scan stops when the received signal
strength matches or exceeds the S-meter setting. Scan resumes
2 seconds after the signal level drops below the S-meter setting.
◆ Starting Scan switches OFF the Automatic Simplex Check.
44
VISUAL SCAN
■ Selecting the Number of Channels
While you are on the air, Visual Scan allows you to
monitor frequencies near the current operating
frequency. Visual Scan graphically and simultaneously
shows how all frequencies in the selected range are
busy. You will see up to 21 segments, for each channel,
that represent 7 S-meter levels (3 segments per level).
1 Press [MNU] to enter Menu mode.
You will determine the scan range by selecting the
center frequency and the number of channels. The
default number of channels is 61.
4 Press [UP]/ [DWN] to select “VISUAL SCAN (1–
9–2)”, then press [OK].
2 Press [UP]/ [DWN] to select “RADIO (1–)”, then
press [OK].
3 Press [UP]/ [DWN] to select “AUX (1–9–)”, then
press [OK].
5 Press [UP]/ [DWN] to select 31, 61 (default), 91,
or 181.
6 Press [OK] to complete the setting.
7 Press [MNU] to exit Menu mode.
45
■ Using Visual Scan
1 Select the desired band.
2 Turn the Tuning control, or press Mic [UP]/
[DWN], to select the operating frequency.
• This frequency will also be used as the center
frequency.
3 Press [F], [VISUAL] to start Visual Scan.
Note:
◆ If you start Visual Scan in Memory Recall mode, the memory
channel frequencies will be scanned.
◆ If you start Visual Scan after recalling the Call channel, the call
channel frequency will be used as the center frequency.
◆ If the frequency range specified for Program Scan or Program
VFO is narrower than the range specified for Visual Scan, the
range for Program Scan or VFO will be used for Visual Scan.
◆ Visual Scan stops while transmitting.
◆ Starting Visual Scan switches Automatic Band Change OFF.
◆ If you start Visual Scan in one of the following conditions, you
cannot receive in the current operating frequency. To use this
frequency, press [PAUSE] to halt Scan.
• Memory Recall or Call Channel mode
• A frequency in the range 118 MHz to 136 MHz was selected
◆
• To halt Scan, press [PAUSE]. “PAUSE” appears and
blinks. Press [PAUSE] again to resume.
4 To change the operating frequency, turn the
Tuning control or press Mic [UP]/ [DWN].
• The displayed frequency changes and the cursor
moves.
• Press [SET] to use the changed operating frequency
as the center frequency.
• Press [RESET] to restore the previous operating
frequency.
5 To quit Visual Scan, press [ESC].
46
in VFO mode.
Depending on conditions, Visual Scan and the conventional Smeter may indicate different signal strength levels.
SELECTING SCAN RESUME METHOD
1 Press [MNU] to enter Menu mode.
The transceiver stops scanning at a frequency (or
memory channel) on which a signal is detected. It then
continues scanning according to which resume mode
you select. You can choose one of the following modes.
The default is Time-operated mode.
2 Press [UP]/ [DWN] to select “RADIO (1–)”, then
press [OK].
•
Time-Operated mode
3 Press [UP]/ [DWN] to select “AUX (1–9–)”, then
press [OK].
4 Press [UP]/ [DWN] to select “SCAN RESUME (1–9–
1)”, then press [OK].
The transceiver remains on a busy frequency (or
memory channel) for approximately 5 seconds, and
then continues to scan even if the signal is still
present.
•
Carrier-Operated mode
The transceiver remains on a busy frequency (or
memory channel) until the signal drops out. There is
a 2 second delay between signal drop-out and scan
resumption.
•
Seek mode
5 Press [UP]/ [DWN] to select Time-Operated (default),
Carrier-Operated, or Seek.
6 Press [OK].
7 Press [MNU] to exit Menu mode.
The transceiver remains on a busy frequency (or
memory channel) even after the signal drops out and
does not automatically resume scanning.
Note: To temporarily stop scanning and monitor weak signals, press and
hold the Mic PF key assigned the Monitor function {page XX}. Release
the key to resume scanning.
47
VFO SCAN
MEMORY SCAN
VFO Scan monitors all frequencies tunable on the band,
using the current frequency step size.
Use Memory Scan to monitor all memory channels
programmed with frequency data.
1 Select the desired band.
1 Select the desired band.
2 Press [VFO] (1 s).
2 Press [MR] (1 s).
• Scan starts at the frequency currently displayed.
• Scan starts with the channel last recalled.
• The 1 MHz decimal blinks while scanning is in progress.
• The 1 MHz decimal blinks while scanning is in progress.
• To reverse the scan direction, turn the Tuning control
clockwise (upward scan) or counterclockwise
(downward scan). You can also press Mic [UP]/ [DWN].
• To reverse the scan direction, turn the Tuning control
clockwise (upward scan) or counterclockwise
(downward scan). You can also press Mic [UP]/ [DWN].
3 To quit VFO Scan, press [ESC].
3 To quit Memory Scan, press [ESC].
Note:
◆ On the current band at least 2 or more memory channels must
contain data and must not be locked out.
◆ The L0 to L9 and U0 to U9 memory channels are not scanned.
◆ You can also start Memory Scan when in Channel Display mode.
While Scan is being interrupted, the channel number blinks.
48
■ Locking Out a Memory Channel
Select memory channels that you prefer not to
monitor while scanning.
1 Recall the desired memory channel.
2 Press [MNU] to enter Menu mode.
3 Press [UP]/ [DWN] to select “RADIO (1–)”, then
press [OK].
3 Press [UP]/ [DWN] to select “MEMORY (1–4–)”,
then press [OK].
4 Press [UP]/ [DWN] to select “LOCKOUT (1–4–1)”,
then press [OK].
GROUP SCAN
For the purpose of Group Scan, the 200 memory
channels are divided into 10 groups, with each group
containing 20 channels. Group Scan monitors only the
20 channels which belong to the specified group. The
channels are grouped as below:
Nos. 1 ~ 20
Nos. 101 ~ 120
Nos. 21 ~ 40
Nos. 121 ~ 140
Nos. 41 ~ 60
Nos. 141 ~ 160
Nos. 61 ~ 80
Nos. 161 ~ 180
Nos. 81 ~ 100
Nos. 181 ~ 200
1 Recall one of the memory channels in the desired
group.
2 Press [MR] (1 s).
• Scan starts with the channel last recalled.
5 Press [UP]/ [DWN] to switch Lockout ON (or
OFF).
6 Press [OK] to complete the setting.
7 Press [MNU] to exit Menu mode.
Note:
◆ The L0 to L9 and U0 to U9 memory channels cannot be locked
out.
◆ If you have recalled a memory channel on the non-control band
(A or B), you cannot select the same channel on the control band
to lock out.
• The 1 MHz decimal blinks while scanning is in progress.
• To reverse the scan direction, turn the Tuning control
clockwise (upward scan) or counterclockwise
(downward scan). You can also press Mic [UP]/ [DWN].
3 To quit Group Scan, press [ESC].
Note:
◆ At least 2 or more memory channels in the specified group must
contain data and must not be locked out.
◆ You can also start Memory Scan when in Channel Display mode.
While Scan is being interrupted, the channel number blinks.
49
PROGRAM SCAN
Program Scan is identical with VFO Scan except that
you select the frequency range of the scan.
6 Press [M.IN].
• The lower limit is stored in the channel.
7 Select the desired frequency as the upper limit.
8 Press [F].
9 Press [UP]/ [DWN] to select a matching channel
in the range U0 to U9.
• If you have selected for example L3 in step 5, select
U3.
■ Setting Scan Limits
You can store up to 10 scan ranges in memory
channels L0/U0 to L9/U9.
1 Select the desired band.
2 Press [VFO].
3 Select the desired frequency as the lower limit.
4 Press [F].
• A memory channel number appears and blinks.
5 Turn the Tuning control, or press Mic [UP]/
[DWN], to select a channel in the range L0 to L9.
50
10 Press [M.IN].
• The upper limit is stored in the channel.
To confirm the stored scan limits, press [MR], then
select the L and U channels.
Note:
◆ The lower limit must be lower in frequency than the upper limit.
◆ The lower and upper frequency step sizes must be equal.
◆ The lower and upper limits must be selected on the same band.
■ Using Program Scan
1 Select the appropriate band.
2 Press [VFO] .
3 Select a frequency equal to or between the
programmed scan limits.
4 Press [VFO] (1 s).
MHz SCAN
MHz Scan monitors a 1 MHz segment of the band, using
the current frequency step size. The current 1 MHz digit
determines the limits of the scan. For example, if the
current frequency is 145.400 MHz, then the scan range
would be from 145.000 MHz to 145.995 MHz. The exact
upper limit depends on the current frequency step size.
• Scan starts at the frequency currently displayed.
• The 1 MHz decimal blinks while scanning is in
progress.
• To reverse the scan direction, turn the Tuning
control clockwise (upward scan) or counterclockwise
(downward scan). You can also press Mic [UP]/
[DWN].
5 To quit Program Scan, press [ESC].
Note:
◆ If the step size of the current VFO frequency differs from that of
the programmed frequencies, you cannot use Program Scan.
◆ If the step size differs between the lower limit and the upper limit,
you cannot use Program Scan.
◆ If the current VFO frequency is within more than one
programmed scan range, the range stored in the smallest
channel number is used.
1 Select the desired band.
2 Press [VFO] to select VFO mode.
3 Select a frequency within the desired 1 MHz
segment.
4 Press [MHz] (1 s) to start MHz Scan.
• Scan starts at the frequency currently displayed.
• The 1 MHz decimal blinks while scanning is in progress.
• To reverse the scan direction, turn the Tuning control
clockwise (upward scan) or counterclockwise
(downward scan). You can also press Mic [UP]/ [DWN].
5 To quit MHz Scan, press [ESC].
51
CALL/VFO SCAN
Use Call/VFO Scan to monitor both the Call channel and
the current VFO frequency on the selected band.
1 Select the desired band.
2 Press [VFO].
3 Select the desired frequency.
4 Press [CALL] (1 s) to start Call/VFO Scan.
• The 1 MHz decimal blinks while scanning is in progress.
5 To quit Call/VFO Scan, press [ESC].
CALL/MEMORY SCAN
Use Call/Memory Scan to monitor both the Call channel
and the desired memory channel.
1 Recall the desired memory channel.
2 Press [CALL] (1 s) to start Call/Memory Scan.
• The 1 MHz decimal blinks while scanning is in progress.
• The Call channel on the same band as of the selected
memory channel is used for Scan.
3 To quit Call/Memory Scan, press [ESC].
Note: The memory channel last used is scanned even if it has been
locked out.
52
CONTINUOUS TONE CODED SQUELCH SYSTEM (CTCSS)
You may sometimes want to hear calls from only specific
persons. The Continuous Tone Coded Squelch System
(CTCSS) allows you to ignore (not hear) unwanted calls
from other persons who are using the same frequency.
First select the same CTCSS tone as selected by the
other persons in your group. A CTCSS tone is
subaudible and is selectable from among the 38
standard tone frequencies.
Note: CTCSS does not cause your conversation to be private. It only
relieves you from listening to unwanted conversations.
USING CTCSS
1 Press the left or right [BAND SEL] to select band A or
B.
• If necessary, press [F], then the same [BAND SEL] to
recall the sub-band.
2 Press [TONE] to activate the CTCSS function.
• “CT” appears when the CTCSS function is ON.
• Each press of [TONE] changes the selection as Tone –>
CTCSS –> DCS –> No selection.
3 Press [F], [T.SEL].
• The current CTCSS frequency appears and blinks.
4 Press [UP]/ [DWN] to select a CTCSS frequency.
• The selectable frequencies are the same as for the tone
frequency. See the table given in “Selecting a Tone
Frequency” {page XX}.
5 Press [OK] to complete the setting.
You will hear calls only when the selected tone is
received. To answer the call, press and hold Mic [PTT],
then speak into the microphone.
Skip steps 3 to 5 if you have already programmed the
appropriate CTCSS frequency.
53
After programming one of the Mic PF keys as the
ENTER key {page XX}, you can also select a CTCSS
frequency by direct entry from the Mic keypad. In step 3,
press [ENTER], then enter 01 to 38 shown in the table
{page XX}. To select 100 Hz, for example, press
[ENTER], [0], [1], [2].
Note:
◆ You can select a separate tone frequency for the CTCSS and Tone
functions.
◆ You cannot use the CTCSS with the Tone or DCS function.
◆ If you select a high tone frequency, receiving audio or noise that
contains the same frequency portions may cause CTCSS to function
incorrectly. To prevent noise from causing this problem, select an
appropriate noise squelch level {page XX}.
3 Press [SCAN] to activate the CTCSS Freq. ID.
“CT SCAN” appears.
• To reverse the scan direction, turn the Tuning control
clockwise (upward scan) or counterclockwise
(downward scan). You can also press Mic [UP]/ [DWN].
• To quit the function, press [ESC].
• When the CTCSS frequency is identified, the identified
frequency appears and blinks.
CTCSS FREQ. ID
This function scans through all CTCSS frequencies to
identify the incoming CTCSS frequency on a received
signal. You may find it useful when you cannot recall the
CTCSS frequency that the other persons in your group
are using.
1 Press [TONE] to switch ON the CTCSS function.
• “CTCSS” appears when the CTCSS function is ON.
2 Press [F], [T.SEL].
• The current CTCSS frequency appears and blinks.
54
4 Press [OK] to program the identified frequency in
place of the currently set CTCSS frequency.
• The previous frequency display is restored with the
CTCSS function remained ON. You may press [TONE]
to switch the CTCSS function OFF.
• Press [ESC] if you do not want to program the identified
frequency.
• Press [SCAN] while the identified frequency is blinking,
to resume scanning.
Note: Received signals are audible while scanning is in progress.
DIGITAL CODE SQUELCH (DCS)
Digital Code Squelch (DCS) is another application which
allows you to ignore (not hear) unwanted calls. It
functions the exact same way as CTCSS. Only the
differences are the encode/ decode method and the
number of selectable codes. DCS uses a burst digital
pulse to encode signals while CTCSS uses continuous
tones. For DCS, you can select from 104 different
codes listed in the table. Because digital pulses can be
inverted, the actual number of selections reaches 208
(104 x 2). You can select Normal or Inverse for each
code.
USING DCS
1 Press the left or right [BAND SEL] to select band A or
B.
• If necessary, press [F], then the same [BAND SEL] to
recall the sub-band.
2 Press [TONE] to activate the DCS function.
• “DCS” appears when the DCS function is ON.
• Each press of [TONE] changes the selection as Tone –>
CTCSS –> DCS –> No selection.
3 Press [F], [T.SEL].
• The current DCS code appears and blinks.
023
025
026
031
032
036
043
047
051
053
054
065
071
072
073
074
114
115
116
122
125
131
132
134
143
145
152
155
156
162
165
172
174
205
212
223
225
226
243
244
245
246
251
252
255
261
263
265
266
271
274
306
311
315
325
331
332
343
346
351
356
364
365
371
411
412
413
423
431
432
445
446
452
454
455
462
464
465
466
503
506
516
523
526
532
546
565
606
612
624
627
631
632
654
662
664
703
712
723
731
732
734
743
754
4 Press [UP]/ [DWN] to select a DCS code, then press
[OK].
5 Press [N/I] to switch between the Normal and Inverse
mode.
• “N” or “I” appears beside the code to indicate the
selected mode.
5 Press [OK] to complete the setting.
You will hear calls only when the selected code is
received. To answer the call, press and hold Mic [PTT],
then speak into the microphone.
Note: You cannot use the DCS with the Tone or CTCSS function.
55
DCS CODE ID
This function scans through all DCS codes to identify the
incoming DCS code on a received signal. You may find
it useful when you cannot recall the DCS code that the
other persons in your group are using.
1 Press [TONE] to switch ON the DCS function.
• “DCS” appears when the Tone function is ON.
2 Press [F], [T.SEL].
• The current DCS code appears and blinks.
3 Press [SCAN] to activate the DCS CODE ID.
“DCS SCAN” appears.
• To reverse the scan direction, turn the Tuning control
clockwise (upward scan) or counterclockwise
(downward scan). You can also press Mic [UP]/ [DWN].
• To quit the function, press [ESC].
• When the DCS code is identified, the identified code
appears and blinks.
56
2 Press [OK] to program the identified code in place of
the currently set code.
• The previous frequency display is restored with the DCS
function remained ON. You may press [TONE] to switch
the DCS function OFF.
• Press [ESC] if you do not want to program the identified
code.
• Press [SCAN] while the identified code is blinking, to
resume scanning.
Note: Received signals are audible while scanning is in progress.
DUAL TONE MULTI-FREQUENCY (DTMF) FUNCTIONS
The keys on the Mic keypad function as DTMF keys; the
12 keys found on a push-button telephone plus 4
additional keys (A, B, C, D). This transceiver provides
10 dedicated memory channels. You can store a DTMF
number (16 digits max.) with a memory name (8 digits
max.) in each of the channels to recall later for a quick
call.
Some repeaters in the U.S.A. and Canada offer a
service called Autopatch. You can access the public
telephone network via such a repeater by sending DTMF
tones. For further information, consult your local
repeater reference.
■ DTMF Monitor
When pressing the Mic DTMF keys, you will not
hear DTMF tones from the speaker. You can also
make the speaker output DTMF tones each time
you press a DTMF key.
Access Menu 1–8–6 (DTMF MONITOR) and
select “ON”.
MANUAL DIALING
Manual Dialing requires only two steps to send DTMF
tones.
1 Press and hold Mic [PTT].
2 Press the keys in sequence on the Mic keypad to
send DTMF tones.
• The corresponding DTMF tones are transmitted.
Freq. (Hz)
1209
1336
1477
1633
697
770
852
941
■ TX Hold
This function makes the transceiver remain in
transmit mode for 2 seconds after you release
each key. So you can release Mic [PTT] after
beginning to press keys.
Access Menu 1–5–3 (TX HOLD) and select “ON”.
57
AUTOMATIC DIALER
If you use the 10 dedicated memory channels to store
DTMF numbers, you need not remember a long string
of digits.
■ Storing a DTMF Number in Memory
Note: Audible DTMF tones from other transceivers near you (or
from your own speaker) may be picked up by your microphone.
If so, you may fail to correctly program a DTMF number.
1 Press [MNU] to enter Menu mode.
2 Select Menu 1–5–1 (STORE), then press [OK].
3 Press [UP]/ [DWN] to select from channel 0 to
9, then press [OK].
6 Repeat steps 4 and 5 to enter up to 8 digits.
Switches among the sets of alphanumeric
CHAR characters, accented letters (TM-D700E only),
and special ASCII characters.
Switches between
Cancels Memory
a/A small and capital
BACK Name Entry.
letters.
Deletes the digit at
Causes the cursor
DEL which the cursor is
].
• The cursor moves to the next digit.
58
9 Press [OK] to complete the programming.
10 Press [MNU] to exit Menu mode.
You can confirm the stored DTMF number by using
steps 1 to 3.
The keypad on the MC-53DM also is available to enter
alphanumeric characters in step 4. See page XX.
■ Transmitting a Stored DTMF Number
1 Press Mic [PTT]+ Mic [PF].
■ Selecting TX Speed
Some repeaters may not respond correctly if a DTMF
number is transmitted at fast speed. If this happens,
change the DTMF number transmission speed from
Fast (default) to Slow.
In Menu mode, access Menu 1–5–2 (TX SPEED) and
select “Slow”.
2 Release only Mic [PF], then turn the Tuning
control to select the desired DTMF memory
channel.
3 While still holding Mic [PTT], press [0] to [9]
corresponding to the channel number.
• The number stored in the channel scrolls across the
display accompanied by DTMF tones from the
speaker.
• After transmission, the frequency display is restored.
■ Selecting Pause Duration
You can also change pause duration stored in
memory channels; the default is 500 msec.
In Menu mode, access Menu 1–5–4 (PAUSE) and
select from 100, 250, 500, 750, 1000, 1500, and 2000
msec.
59
PROGRAMMABLE FUNCTION (PF) KEYS
The Programmable Function keys are [PF], [MR],
[VFO], and [CALL] located on the face of the
microphone. These keys have the following default
functions:
[PF] (PF1)
Band Select
[MR] (PF2)
Memory Recall
[VFO] (PF3)
VFO Select
[CALL] (PF4)
Call Channel Select
(TM-D700E: 1750 Hz Tone TX)
1 Press [MNU] to enter Menu mode.
2 Press [UP]/ [DWN] to select “RADIO (1–)”, then
press [OK].
3 Press [UP]/ [DWN] to select “MIC (1–8–)”, then press
[OK].
4 Press [UP]/ [DWN] to select “PF1 (1–8–1)” to “PF4
(1–8–4)”, then press [OK].
If you prefer, you can change the defaults to the
following key functions:
Key Function
PWR (PF1only)
MONITOR
ENTER
VOICE 1
MENU
VFO
MR
CALL
MHz
TONE
REV
LOW
Ref.
Ref.
Ref.
Key Function
Key Function
Page
Page
Page
MUTE
CTRL
BAND A SEL
BAND B SEL
PM IN
A.B.C.
M>V
M. IN
C. IN
LOCK
T. SEL
SHIFT
STEP
VISUAL
DIM
6 Press [OK] to complete the setting.
7 Press [MNU] to exit Menu mode.
SUB-BAND SEL
TNC
LIST
P. MON
BCON
MSG
POS
DX
Without an optional VS-3 unit installed, pressing this key
causes the transceiver to announce the current frequency
using beeps of different frequencies. Press the key again to
stop the beeps.
60
5 Press [UP]/ [DWN] to select the desired function.
After switching the power OFF, you may press Mic [PF]+
POWER ON. This allows you to skip steps 1 to 4. Press
Mic [MR], [VFO], or [CALL] instead of [PF] as
necessary.
Note:
◆ To restore the default functions, perform Full Reset {page XX}.
◆ If the LOCK switch located on the rear of the microphone is ON, you
cannot reprogram the Programmable Function keys.
AUXILIARY FUNCTIONS
DIRECT FREQUENCY ENTRY
If the desired operating frequency is far from the current
frequency, using the Mic keypad is the quickest way to
change frequency. First program one of the Mic PF keys
as the ENTER key {page XX},
1 Press the left or right [BAND SEL] to select band A or
B.
• If necessary, press [F], then the same [BAND SEL] to
recall the sub-band.
2 Press [VFO].
3 Press Mic [ENTER].
• The display for Direct Frequency Entry appears.
If you press Mic [PF] while entering a frequency, the new
data is accepted for the digits entered and the previous
data remains unchanged for the digits not yet entered.
Previous freq.:
145.350 MHz
Note: The 1 kHz and subsequent digits may be corrected depending on
combinations of the previous frequency and the current frequency step
size.
If you press Mic [*] while entering a frequency, the new
data is accepted for the digits entered and 0 is
programmed for the digits not yet entered.
Previous freq.:
145.350 MHz
4 Press the numeric keys in sequence on the keypad.
Note:
◆ The 1 kHz and subsequent digits are corrected according to which
key is pressed for the 1 kHz digit.
◆ Entering a digit that is outside the allowable range causes the nearest
digit within range to be displayed.
◆ You cannot enter a frequency in a band which cannot be recalled on
the current band.
61
CHANGING FREQUENCY STEP SIZE
PROGRAMMABLE VFO
Choosing the correct step size is essential in order to
select your exact receive frequency using the Tuning
control or Mic [UP]/ [DWN]. The default step size on the
VHF band is 5 kHz (U.S.A./ Canada) or 12.5 kHz. The
default on the UHF band is 25 kHz no matter which
market version.
If you always check frequencies within a certain range,
set upper and lower limits for frequencies that are
selectable using the Tuning control or Mic [UP]/
[DWN]. For example, if you select 145 MHz for the
lower limit and 146 MHz for the upper limit, the tunable
range will be from 145.000 MHz to 146.995 MHz.
1 Press the left or right [BAND SEL] to select band A or
B.
1 Press the left or right [BAND SEL] to select band A
or B.
• If necessary, press [F], then the same [BAND SEL] to
recall the sub-band.
2 Press [F], [STEP].
• The current step size appears.
• If necessary, press [F], then the same [BAND SEL]
to recall the sub-band.
2 Press [MNU], select Menu 1–3–1
(PROGRAMMABLE VFO), then press [OK].
• The current lower frequency limit blinks.
3 Press [UP]/ [DWN] to select the desired step size,
then press [OK].
• The selectable step sizes are 5, 6.25, 10, 12.5, 15, 20,
25, 30, 50, and 100 kHz.
4 Press [OK] to complete the setting.
Note: Changing between step sizes may correct the displayed
frequency. For example, if 144.995 MHz is displayed with a 5 kHz step
size selected, changing to a 12.5 kHz step size corrects the displayed
frequency to 144.9875 MHz.
62
3 Press [UP]/ [DWN] to select the desired lower
frequency limit, then press [OK].
• The current upper frequency limit blinks.
4 Press [UP]/ [DWN] to select the desired upper
frequency limit, then press [OK].
5 Press [MNU] to exit Menu mode.
Note:
◆ You cannot program the 100 kHz and subsequent digits.
◆ The exact 100 kHz and subsequent digits of the upper limit
depend on the frequency step size selected.
DISPLAY DIMMER
DISPLAY CONTRAST ADJUST
You can manually change the display illumination to suit
the lighting conditions where you are operating.
The display visibility changes depending on ambient
conditions, for example between daytime and nighttime.
When you find the display is not clear, use this function
to select the optimum display contrast.
1 Press [F], [DIM].
• The current illumination level appears.
2 Press [UP]/ [DWN] to select from 5 levels, including
OFF.
Access Menu 1–1–2 (CONTRAST) and select from level
1 to 16. The default is level 8.
• The default is level 1.
3 Press [OK] to complete the setting.
Note: Selecting OFF automatically switches Auto Dimmer Change ON.
POSITIVE/ NEGATIVE REVERSAL
You can change the display status between Negative
(default) and Positive using Menu 1–1–3 (REVERSE
MODE).
AUTO DIMMER CHANGE
This function increases the display intensity one step
brighter for approximately 5 seconds when you press a
front panel button or Mic key, or turn the Tuning control.
No change occurs if you have selected the brightest
level.
Access Menu 1–1–4 (AUTO DIMMER) and select “ON”.
63
BLANKING A BAND DISPLAY
AUTOMATIC BAND CHANGE (A.B.C.)
If you have no plans to use band A or B, quit frequency
display on the unused band. This saves power
consumption and makes it simpler to read the
information you need.
A.B.C. will temporarily switch the RX only band to the TX
band immediately after a signal is received on the RX
only band. This function allows you to reply to a caller
without manually selecting the correct band.
Press the left [BAND SEL] (1 s) to blank band A, or the
right [BAND SEL] (1 s) to blank band B.
Press [F], [A.B.C] to switch the function ON (or OFF).
To restore Dual-band mode, press the same [BAND
SEL] (1 s).
• Pressing [BAND SEL] or Mic [PTT] also cancels A.B.C.
Note: You cannot operate the blanked band nor use this band to receive
or transmit.
64
• “A.B.C.” appears when the function is ON.
• The original TX band is restored 2 seconds after signals
drop out.
Note:
◆ You cannot use A.B.C. when in Single-band mode. After activating
A.B.C., changing from Dual-band mode to Single-band mode
deactivates A.B.C. Switching back to Dual-band mode re-activates
A.B.C.
◆ After activating A.B.C., starting Visual Scan deactivates A.B.C.
Canceling Visual Scan re-activates A.B.C.
TRANSCEIVER LOCK
CHANGING MULTI-FUNCTION BUTTON LABELS
Transceiver Lock is suitable for a typical mobile
installation where you alter most functions with your
microphone. This Lock disables all functions excluding
the following:
The functions to be frequently used should differ among
persons. You can change the defaults of the 5 buttons
located below the display.
PWR switch
SQL controls
[F]
VOL controls
[F], [MHz]
Mic keys
Press [F], [MHz] to switch the function ON (or OFF).
• “LOCK” appears when the function is ON.
Access Menu 1–1–5 (KEY FUNCTION) and select mode
1 (default), 2, or 3.
Mode 1
[KEY]
[F], [KEY]
[F] (1 s), [KEY]
TONE
REV
T.SEL SHIFT
LIST
LOW
MUTE
STEP VISUAL
P.MON BCON
MSG
CTRL
DIM
POS
Mode 2
[KEY]
ALL-CONTROL LOCK
All-control Lock is ideal when you have no plans to
transmit but you want to monitor a specific frequency.
This Lock disables all functions excluding power ON/
OFF and All-control Lock ON/OFF.
T.SEL SHIFT
[F], [KEY]
LIST
[F] (1 s), [KEY]
TONE
[KEY]
LIST
STEP VISUAL
P.MON BCON
REV
LOW
DIM
MSG
POS
MUTE
CTRL
MSG
POS
MUTE
CTRL
Mode 3
[F], [KEY]
[F] (1 s), [KEY]
TONE
P.MON BCON
REV
T.SEL SHIFT
LOW
STEP VISUAL
DIM
After switching Transceiver Lock ON, switch OFF the
transceiver, then press [MHz]+ POWER ON to switch
the function ON (or OFF).
• “ALL LOCK” appears when the function is ON.
65
S-METER SQUELCH
S-meter Squelch causes the squelch to open only when
a signal with the same or greater strength than the Smeter setting is received. This function relieves you from
constantly resetting the squelch when receiving weak
stations that you have no interest in.
1 Select the desired band.
2 Press [MNU] to enter Menu mode.
3 Select 1–3–2 (S-METER SQUELCH) then press
[OK].
4 Press [UP] /[DWN] to switch the function ON (or
OFF).
5 Press [OK] to complete the setting.
6 Press [MNU] to exit Menu mode.
• The S-meter setting segments appear.
66
7 To select the desired S-meter setting, turn the left
(band A) or right (band B) SQL control depending on
which band you selected.
■ Squelch Hang Time
When using S-meter Squelch, you may want to adjust
the time interval between when the received signals
drop and when the squelch closes.
Access Menu 1–3–3 (SQUELCH HANG TIME) and
select from OFF (default), 125, 250 and 500 msec.
Note: Menu 1–3–3 is selectable only when the S-meter Squelch is
ON.
CHANGING BEEP VOLUME
SWITCHING FM/AM MODE
The transceiver beeps each time you press a front panel
button or Mic key, or when it receives appropriate APRS
or DX cluster data. You can change the beep volume or
turn it off.
On this transceiver you can switch between FM and AM
to receive on band A. The default mode on the 118 MHz
band is AM while the default on the 144 MHz band and
the 440 (or 430) MHz sub-band is FM.
Access Menu 1–2–1 (BEEP VOLUME) and select the
volume from levels 1 to 7 and OFF. The default is level
5.
After recalling the desired band on band A, access Menu
1–3–4 (FM/AM MODE) and switch between FM and AM.
• The 1 MHz decimal becomes long when AM is selected.
Note: After selecting OFF, you will still hear TOT and APO alarms.
Note: You cannot switch between FM and AM to receive on band B.
KEY BEEP ON/ OFF
ADVANCED INTERCEPT POINT (AIP)
If you are annoyed by beeps generated when pressing a
front panel button or Mic key, switch OFF the Key Beep.
The transceiver will beep only when it receives
appropriate APRS or DX cluster data.
The VHF band is often crowded in urban areas. AIP
helps eliminate interference and reduce audio distortion
caused by intermodulation. You may use this function
when operating on the VHF band.
Access Menu 1–2–2 (KEY BEEP) and select “OFF”.
Access Menu 1–3–5 (VHF AIP) and select “ON”.
Note:
◆ This transceiver does not allow you to use the AIP on the UHF band.
◆ Switching ON the AIP also affects the VHF sub-band on band B.
67
TIME-OUT TIMER (TOT)
AUTOMATIC POWER OFF (APO)
It is sometimes necessary or desirable to restrict a single
transmission to a specific maximum time. You may use
this function to prevent repeater time-outs when
accessing repeaters, or to conserve battery power.
Automatic Power Off is a background function that
monitors whether any buttons or keys have been
pressed, or whether the Tuning control has been turned.
After 3 hours pass with no operations, APO turns OFF
the power. However, 1 minute before the power turns
OFF, “APO” blinks and a series of warning tones sound.
When TOT times out, the transceiver generates beeps
and automatically returns to receive mode. To resume
transmitting, release and then press Mic [PTT] again.
Access Menu 1–9–3 (APO) and select “ON”.
Access Menu 1–9–4 (TOT) and select 3, 5, or 10
(default) minutes for the TOT time.
Note: If the squelch opens or any settings are changed during the 3 hour
period while APO is ON, the timer resets. When the squelch closes or
you stop changing the settings, the timer begins counting again from 0.
68
POWER-ON MESSAGE
Each time you switch the transceiver ON, “HELLO !!”
appears and stays for approximately 1 second. You can
program your favorite message in place of the factory
default.
1 Press [MNU] to enter Menu mode.
2 Select Menu 1–1–1 (POWER-ON MSG), then press
[OK].
• The display for entering a message appears; the first
digit blinks.
Switches among the sets of alphanumeric
CHAR characters, accented letters (TM-D700E only),
and special ASCII characters.
Switches between
Cancels Message
a/A small and capital
BACK Entry.
letters.
Deletes the digit at
Causes the cursor
DEL which the cursor is
].
• The cursor moves to the next digit.
5 Repeat steps 3 and 4 to enter up to 8 digits.
By initiating this function, various pre-programmed
displays appear. You still can normally use the
transceiver in this mode. Pressing a front panel button
or Mic key, or turning the Tuning control restores the
operating display immediately. If there is no button/key
entry or Tuning control adjustment for approximately
10 seconds, the transceiver reverts back to
Demonstration mode.
Press [F]+ POWER ON to switch the function ON (or
OFF).
69
CHANGING SPEAKER CONFIGURATIONS
SPEAKER MUTE
This transceiver has two speaker jacks. You can enjoy a
variety of speaker configurations by using one or two
external speakers. Access Menu 1–2–3 (SPEAKER)
and select mode 1 (default) or 2, depending on how the
internal and/or external speakers should function.
While programming the control band (not TX band), you
may not want to hear audio received on that band. Use
this function to mute the speaker allocated to the control
band.
Connection
Press [MUTE] to switch the function ON (or OFF).
• “MUTE” appears when the function is ON.
Mode
Band A
Band B
Only SP1 jack
connected with an
external speaker
Mode A
External
External
Mode B
External
External
Only SP2 jack
connected with an
external speaker
Mode A
Internal
External
Mode B
External
Internal
Both SP1 and SP2
jacks connected
with external
speakers
Mode A
External 1
External 2
SWITCHING TX DEVIATION (TM-D700E ONLY)
Mode B
External 2
External 1
This transceiver is capable of switching between wide
and narrow deviations to transmit. After selecting the
desired band, access Menu 1–3–7 (WIDE/NARROW)
and switch between Wide (default) and Narrow.
• When Narrow is selected, “N” appears beside the
frequency.
Note: Do not select Narrow for the band to be used for transmitting
packets.
70
MICROPHONE CONTROL (U.S.A./ CANADA ONLY)
You can change numerous transceiver settings by
operating the Mic DTMF keys. To activate this function,
access Menu 1–8–5 (MIC CONTROL) and select “ON”.
The following table shows what function is switched ON
and OFF or which setting is changed, by pressing the
DTMF keys.
Visual Scan
Squelch Adjustment 2, 3
Tone/ CTCSS
TX Power Change
Reverse
Enter
1 MHz Step Change
Dimmer Level Change
D [F] key
Monitor
Frequency Readout
by Beeps 1
Volume Change 2, 3
Speaker Mute
—
You can also make the following settings by pressing [D]
first (ex. [D], then [2]).
Tone Select 1
Offset Direction Select
DTMF Keypad Lock
DTMF Keypad Unlock
C Repeater
ulti-function Mode
D M
Cancel
E DOWN
Band A/ B Select
Sub-band Select
UP
After entering the selection mode, press [ ] or [#] to change
the level or selection.
First press [2] to activate the Tone or CTCSS function.
Press [OK] on the front panel of the transceiver to complete
the setting.
Note:
◆ Audible DTMF tones from other transceivers near you may be picked
up by your MC-53DM microphone. If so, this could prevent the
function from working correctly.
◆ U.S.A. Only: It is illegal to transmit control codes on the VHF band.
Transmit control codes only on the UHF band.
Down 4
Up 4
Transceivers equipped with the optional VS-3 unit announce
the displayed information {page XX}.
After entering the selection mode, press [ ] or [#] to change
the level or selection.
Both Volume Change and Squelch Adjustment cannot be
activated at the same time.
Both Volume Change and Squelch Adjustment must be OFF
to change the tone or frequency step using this key.
71
WIRELESS REMOTE CONTROL (U.S.A./ CANADA ONLY)
If you also have a compatible KENWOOD handy
transceiver, you may use it as a remote control for this
mobile transceiver. You will control one band on the
mobile while sending DTMF tones to the other band from
the handheld. This function will be useful, for example,
when you want to control the mobile from a location
outside your vehicle.
Note:
◆ The handy transceiver must have both the DTSS and Remote
Control functions. A TH-D7A transceiver, which does not have the
DTSS, also is available because of its enhanced Remote Control
function.
◆ The FCC rules permit you to send control codes only on the 440 MHz
band.
PREPARATION
Let us assume band A (VHF) of the mobile transceiver
will be controlled.
On the handy transceiver:
1 Program the DTSS code as the secret number.
• For the programming method, see the instruction
manual for the handy transceiver.
• If using a TH-D7A, see “WIRELESS REMOTE
CONTROL” on its instruction manual.
2 Select the transmit frequency on the UHF band.
3 Make the transceiver enter Remote Control mode.
• For the method, see the instruction manual for the
handy transceiver. If not described, consult your dealer.
On the mobile transceiver:
4 Access Menu 1–A–1 (CODE), and select the same
secret number as you selected in step 1.
• Turn the Tuning control to select each digit. Press [->]
(or [<-]) to move the cursor to the next (or previous)
digit.
72
• You can also press Mic [0] to [9] in sequence to enter 3
digits.
5 Select the receive frequency on band B (UHF).
• Mate this frequency with the transmit frequency on the
handy transceiver.
6 Select band A (VHF) as the TX band or Control band
{page XX}.
7 To cause the mobile to send a control
acknowledgment to the handy transceiver, access
Menu 1–A–2 (ANSWER BACK) and select “ON”.
DCS ON
MR
TONE ON
LOW
CTCSS ON
ENTER
DCS OFF
TONE SEL
TONE OFF
REPEATER ON
CTCSS OFF
REPEATER OFF
CALL
DOWN
VFO
UP
To change the transmit/ receive frequency:
• DTMF tones which represent the secret number will be
used as an acknowledgment.
8 Access Menu 1–A–3 (CONTROL) and select “ON”.
• “REMOTE CON” and “LOCK” appear when the
transceiver enters Remote Control mode.
([VFO] ➡ [ENTER] ➡ [0] ~ [9] (enter the necessary
digits) ➡ [ENTER]) or ([VFO] ➡ [UP]/ [DWN])
To recall a memory channel:
([MR] ➡ [ENTER] ➡ [0] ~ [9] (enter the necessary
digits) ➡ [ENTER]) or ([MR] ➡ [UP]/ [DWN])
To change the tone (or CTCSS) frequency:
CONTROL OPERATION
([TONE SEL] ➡ [0] ~ [9] (enter 2 digits; ex. [0], [5]) ➡
[TONE SEL])
When in Remote Control mode, the DTMF keys of the
handy transceiver will function as shown in the table.
Each time you press the desired key, the handy
transceiver will automatically enter transmit mode and
send the corresponding command to the mobile
transceiver.
• Use Nos. 01 to 38 shown in the table in page XX.
• First activate the Tone or CTCSS function. You can select a
separate tone frequency for the Tone and CTCSS functions.
Note: When in Remote Control mode, you can perform only the following
operations on the mobile transceiver.
•
•
Transmit
Secret Number Change
•
•
Answer Back ON/ OFF
Partial/ Full Reset
73
SKY COMMAND 2 (U.S.A./ CANADA ONLY)
The Sky Command 2 allows remote control of a
TS-570D, TS-570S, or TS-870S HF transceiver. Besides
the HF transceiver, this system requires two transceivers
capable of working the Sky Command 2. This
transceiver and TH-D7A handhelds are currently
available. You will use one transceiver as a control
station called “Commander”. The transceiver connected
with the HF transceiver is called “Transporter”. It will
function as an interface between the Commander and
the HF transceiver. This system allows you, for
example, to watch for and hunt DX while washing your
car, or to operate the HF transceiver while relaxing in
your car, living room, or patio, instead of in your shack.
74
Both the Commander and Transporter use Full Duplex
function to transfer audio and commands as below:
CONNECTING THE TRANSPORTER WITH THE HF
TRANSCEIVER
Note:
◆ Switch OFF both the Transporter and HF transceiver before making
the connection.
◆ The Transporter automatically transmits its call sign in Morse at
regular intervals because of the legal requirement; therefore, transmit
sidetone must be output from the HF transceiver. On TS-570D or
TS-570S, do not select “OFF” in Menu 21. On TS-870S, use the
MONI control to adjust the volume of sidetone.
◆ When the Transporter is too close to the HF transceiver, unwanted
feedback may cause malfunction.
◆ Do not share a regulated power supply between the Transporter and
the HF transceiver. Unwanted feedback may cause malfunction.
75
PREPARATION FLOW
The following steps should guide you to a good start of
Sky Command operation. First connect the Transporter
to the HF transceiver {page XX}.
y On the Commander Access Menu 4–3 and select
and Transporter
the tone frequency {page XX}.
• Select the same tone frequency
on both transceivers.
• For the selectable frequencies,
see the table given on page XX.
q On the Commander Select the same VHF and UHF
and Transporter
frequencies.
w On the Commander Access Menu 4–1 to program
a call sign (9 digits max.) for
the Commander {page XX}.
• You may enter your exact call
sign; ex. WD6BQD.
e On the Commander Access Menu 4–2 to program
a call sign (9 digits max.) for
the Transporter {page XX}.
• This call sign must be different
from the one for the
Commander. So you may add
SSID characters; ex.
WD6BQD-1.
r On the Transporter
Access Menu 4–1 to program
the same call sign as you
entered in step w {page XX}.
t On the Transporter
Access Menu 4–2 to program
the same call sign as you
entered in step e {page XX}.
76
u On the Commander Access Menu 4–4 and select
“COMMANDER”.
• “PUSH [ 0 ] KEY TO START
COMMANDER!!” appears.
i On the Transporter
Access Menu 4–4 and select
“TRANSPORTER”.
• “TRANSPORTER” appears.
Now the Commander and Transporter are in Sky
Command mode. For operations in this mode, see
“CONTROL OPERATION” on page XX. First switch ON
the HF transceiver and press [SYNC] on the
Commander. To exit the Sky Command mode, access
Menu 4–4 and select “OFF”.
Note:
◆ Unless you program call signs, you cannot select “COMMANDER” or
“TRANSPORTER” using Menu 4–4.
◆ On the HF transceiver, select 9600 bps and 1 stop bit (default) using
the Menu Set-up function.
◆ Adjust the audio level on both the Transporter and HF transceiver.
◆ To distinguish your various stations or nodes, you can have up to 15
Secondary Station IDentifiers (SSIDs); ex. WD6BQD-1 to WD6BQD15. You always have to put a dash between your call sign and SSID
number.
PROGRAMMING CALL SIGNS
The built-in TNCs of the Commander and Transporter
communicate each other when you send a control
command from the Commander. So you must program
different call signs (9 digits max.) on these transceivers
as the IDs of the TNCs.
Use the following Menu Nos. to program call signs:
On Commander
4 Press [->].
• The cursor moves to the next digit.
5 Repeat steps 3 and 4 to enter up to 9 digits.
Cancels entry of a
BACK call sign.
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 83
Create Date                     : 1999:07:21 14:04:57
Producer                        : Acrobat Distiller 3.02 for Power Macintosh
Subject                         : 
Creator                         : Adobe PageMaker 6.0
Title                           : TM-D700 E 00 Thank you!
Author                          : äCäOíSìñPVX

EXIF Metadata provided by EXIF.tools