JVC KENWOOD 412900 144/430 MHz FM Dual Bander User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1362262
Application ID	bJkdjNgS2XWOeajtGbMtiw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	394kB (4924968 bits)
Date Submitted	2010-10-18 00:00:00
Date Available	2010-11-23 00:00:00
Creation Date	2010-07-18 16:43:02
Producing Software	Adobe PDF Library 7.0
Document Lastmod	2010-07-30 17:32:25
Document Title	User Manual
Document Creator	Adobe InDesign CS2_J (4.0.5)

TH-D72A/ TH-D72E
144/440 MHz FM DUAL BANDER/
144/430 MHz FM DUAL BANDER
INSTRUCTION MANUAL
144/440 MHz FM DOUBLE BANDE/
144/430 MHz FM DOUBLE BANDE
MODE D’EMPLOI
DOBLE BANDA DE 144/440 MHz EN FM/
DOBLE BANDA DE 144/430 MHz EN FM
MANUAL DE INSTRUCCIONES
Only basic operations are explained in this instruction manual. For a
detailed explanation on the operations, refer to the PDF file supplied
on the CD-ROM.
Seules les fonctions de base sont expliquées dans ce mode d’emploi.
Pour le détail sur les autres opérations, reportez-vous au fichier PDF à
votre disposition sur le CD-ROM.
En este manual de instrucciones solamente se explican las
operaciones básicas. Si desea obtener una descripción detallada de
las operaciones, consulte el archivo PDF correspondiente incluido
en el CD-ROM.
© B62‑2235‑00 (K, E)
09 08 07 06 05 04 03 02 01 00
TH-D72A/ TH-D72E
INSTRUCTION MANUAL
ENGLISH
144/440 MHz FM DUAL BANDER/
144/430 MHz FM DUAL BANDER
NOTIFICATION
This equipment complies with the essential requirements of Directive
1999/5/EC.
The use of the warning symbol
means the equipment is subject to
restrictions of use in certain countries.
This equipment requires a licence and is intended for use in the
countries as below.
AT
IE
SE
LT
BE
IT
CH
MT
DK
LI
GB
PL
FI
LU
CY
SK
FR
NL
CZ
SI
DE
NO
EE
BG
GR
PT
HU
RO
IS
ES
LV
ISO3166
Thank You
We are grateful you decided to purchase this Kenwood FM transceiver.
Kenwood always provides Amateur Radio products which surprise and excite
serious hobbyists. This transceiver is no exception. Kenwood believes that this
product will satisfy your requirements for both voice and data communications.
The models listed below are covered by this manual.
TH-D72A: 144/440 MHz FM Dual Bander (The Americas)
TH-D72E: 144/430 MHz FM Dual Bander (Europe)
Features
This transceiver has the following main features:
•
•
•
•
•
A built-in GPS receiver unit.
A built-in TNC which conforms to the AX.25 protocol. With a portable computer, it allows
you to easily enjoy Packet operation.
Includes a program for dealing with data formats supported by Automatic Packet/
Position Reporting System (APRS®).
Contains a total of 1000 Memory channels to program frequencies and other various
data. Each Memory channel can be named using up to 8 alphanumeric characters.
Continuous Tone Coded Squelch System (CTCSS) or Digital Code Squelch (DCS)
rejects unwanted calls from other stations.
Writing Conventions Followed in this Manual
The writing conventions described below have been followed to simplify
instructions and avoid unnecessary repetition.
Instruction
Action
Press [KEY].
Momentarily press KEY.
Press [KEY] (1s).
Press and hold KEY for 1 second or longer.
Press [KEY1], [KEY2].
Press KEY1 momentarily, release KEY1, then press
KEY2.
Press [F], [KEY].
Press the F key to enter Function mode, then press
KEY to access its secondary function.
Press [KEY] + Power ON.
With the transceiver power OFF, press and hold
KEY while turning the transceiver power ON.
Information on Disposal of Old Electrical and Electronic Equipment and Batteries (applicable
for EU countries that have adopted separate waste collection systems)
Products and batteries with the symbol (crossed-out wheeled bin) cannot be disposed
as household waste.
Old electrical and electronic equipment and batteries should be recycled at a facility
capable of handling these items and their waste byproducts. Contact your local
authority for details in locating a recycle facility nearest to you. Proper recycling and
waste disposal will help conserve resources whilst preventing detrimental effects on
our health and the environment.
Notices to the User
One or more of the following statements may be applicable:
FCC WARNING
This equipment generates or uses radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the
instruction manual. The user could lose the authority to operate this equipment if an unauthorized
change or modification is made.
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can generate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that the interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer for technical assistance.
WHEN CONDENSATION OCCURS INSIDE THE TRANSCEIVER
Condensation may occur inside the transceiver in such a case where the room is warmed using
a heater on cold days or where the transceiver is quickly moved from a cold room to a warm room.
When condensation occurs, the microcomputer and/or the transmit/receive circuits may become
unstable, resulting in transceiver malfunction. If this happens, turn OFF the transceiver and just
wait for a while. When the condensation droplets disappear, the transceiver will function normally.
ATTENTION: (USA only)
The RBRC Recycle seal found on Kenwood lithium-ion (Li-ion) battery packs indicates
Kenwood’s voluntary participation in an industry program to collect and recycle Li-ion
batteries after their operating life has expired. The RBRC program is an alternative to
disposing Li-ion batteries with your regular refuse or in municipal waste streams, which is
illegal in some areas.
For information on Li-ion battery recycling in your area, call (toll free) 1-800-8-BATTERY
(1-800-822-8837).
Kenwood’s involvement in this program is part of our commitment to preserve our environment and conserve
our natural resources.
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special
handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
Precautions
•
•
Do not charge the transceiver and battery pack when they are wet.
Ensure that there are no metallic items located between the transceiver and the battery
pack.
Do not use options not specified by Kenwood.
If the die-cast chassis or other transceiver part is damaged, do not touch the damaged
parts.
If a headset or headphone is connected to the transceiver, reduce the transceiver
volume. Pay attention to the volume level when turning the squelch off.
Do not place the microphone cable around your neck while near machinery that may
catch the cable.
Do not place the transceiver on unstable surfaces.
Ensure that the end of the antenna does not touch your eyes.
When the transceiver is used for transmission for many hours, the radiator and chassis
will become hot. Do not touch these locations when replacing the battery pack.
Do not immerse the transceiver in water.
Always switch the transceiver power off before installing optional accessories.
For safety reasons, we recommend that the AC adapter (for the battery charger) be
connected to an easily accessible AC socket.
•
•
•
•
•
•
•
•
•
•
Turn the transceiver power off in the following locations:
• In explosive atmospheres (inflammable gas, dust particles, metallic powders, grain
powders, etc.).
• While taking on fuel or while parked at gasoline service stations.
• Near explosives or blasting sites.
• In aircrafts. (Any use of the transceiver must follow the instructions and regulations
provided by the airline crew.)
• Where restrictions or warnings are posted regarding the use of radio devices,
including but not limited to medical facilities.
• Near persons using pacemakers.
•
•
•
•
•
•
ii
Do not disassemble or modify the transceiver for any reason.
Do not place the transceiver on or near airbag equipment while the vehicle is
running. When the airbag inflates, the transceiver may be ejected and strike the
driver or passengers.
Do not transmit while touching the antenna terminal or if any metallic parts are
exposed from the antenna covering. Transmitting at such a time may result in a
high-frequency burn.
If an abnormal odor or smoke is detected coming from the transceiver, switch the
transceiver power off immediately, remove the battery pack from the transceiver, and
contact your Kenwood dealer.
Use of the transceiver while you are driving may be against traffic laws. Please
check and observe the vehicle regulations in your area.
Do not expose the transceiver to extremely hot or cold conditions.
•
•
Do not carry the battery pack (or battery case) with metal objects, as they may short
the battery terminals.
When operating the transceiver in areas where the air is dry, it is easy to build up
an electric charge (static electricity). When using a earphone accessory in such
conditions, it is possible for the transceiver to send an electric shock through the
earphone and to your ear. We recommend you use only a speaker/microphone in
these conditions, to avoid electric shocks.
Information concerning the battery pack:
The battery pack includes flammable objects such as organic solvent.
Mishandling may cause the battery to rupture producing flames or extreme heat,
deteriorate, or cause other forms of damage to the battery. Please observe the
following prohibitive matters.
•
•
•
•
•
•
•
Do not disassemble or reconstruct battery!
The battery pack has a safety function and protection circuit to avoid danger. If they
suffer serious damage, the battery may generate heat or smoke, rupture, or burst
into flame.
Do not short-circuit the battery!
Do not join the + and – terminals using any form of metal (such as a paper clip or
wire). Do not carry or store the battery pack in containers holding metal objects (such
as wires, chain-necklace or hairpins). If the battery pack is short-circuited, excessive
current will flow and the battery may generate heat or smoke, rupture, or burst into
flame. It will also cause metal objects to heat up.
Do not incinerate or apply heat to the battery!
If the insulator is melted, the gas release vent or safety function is damaged, or the
electrolyte is ignited, the battery may generate heat or smoke, rupture, or burst into
flame.
Do not leave the battery near fire, stoves, or other heat generators (areas
reaching over 80°C/ 176°F)!
If the polymer separator is melted due to high temperature, an internal short-circuit
may occur in the individual cells and the battery may generate heat or smoke,
rupture, or burst into flame.
Do not immerse the battery in water or get it wet by other means!
If the battery’s protection circuit is damaged, the battery may charge at extreme
current (or voltage) and an abnormal chemical reaction may occur. The battery may
generate heat or smoke, rupture, or burst into flame.
Do not charge the battery near fire or under direct sunlight!
If the battery’s protection circuit is damaged, the battery may charge at extreme
current (or voltage) and an abnormal chemical reaction may occur. The battery may
generate heat or smoke, rupture, or burst into flame.
Use only the specified charger and observe charging requirements!
If the battery is charged in unspecified conditions (under high temperature over the
regulated value, excessive high voltage or current over regulated value, or with a
remodeled charger), it may overcharge or an abnormal chemical reaction may occur.
The battery may generate heat or smoke, rupture, or burst into flame.
iii
•
•
•
•
•
•
•
•
•
•
•
iv
Do not pierce the battery with any object, strike it with an instrument, or step
on it!
This may break or deform the battery, causing a short-circuit. The battery may
generate heat or smoke, rupture, or burst into flame.
Do not jar or throw the battery!
An impact may cause the battery to leak, generate heat or smoke, rupture, and/or
burst into flame. If the battery’s protection circuit is damaged, the battery may charge
at an abnormal current (or voltage), and an abnormal chemical reaction may occur.
The battery may generate heat or smoke, rupture, or burst into flame.
Do not use the battery pack if it is damaged in any way!
The battery may generate heat or smoke, rupture, or burst into flame.
Do not solder directly onto the battery!
If the insulator is melted or the gas release vent or safety function is damaged, the
battery may generate heat or smoke, rupture, or burst into flame.
Do not reverse the battery polarity (and terminals)!
When charging a reversed battery, an abnormal chemical reaction may occur. In
some cases, an unexpected large amount of current may flow upon discharging.
The battery may generate heat or smoke, rupture, or burst into flame.
Do not reverse-charge or reverse-connect the battery!
The battery pack has positive and negative poles. If the battery pack does not
smoothly connect with a charger or operating equipment, do not force it; check the
polarity of the battery. If the battery pack is reverse-connected to the charger, it will
be reverse-charged and an abnormal chemical reaction may occur. The battery may
generate heat or smoke, rupture, or burst into flame.
Do not touch a ruptured and leaking battery!
If the electrolyte liquid from the battery gets into your eyes, wash your eyes with
fresh water as soon as possible, without rubbing your eyes. Go to the hospital
immediately. If left untreated, it may cause eye-problems.
Do not charge the battery for longer than the specified time!
If the battery pack has not finished charging even after the regulated time has
passed, stop it. The battery may generate heat or smoke, rupture, or burst into
flame.
Do not place the battery pack into a microwave or high pressure container!
The battery may generate heat or smoke, rupture, or burst into flame.
Keep ruptured and leaking battery packs away from fire!
If the battery pack is leaking (or the battery emits a bad odor), immediately remove it
from flammable areas. Electrolyte leaking from battery can easily catch on fire and
may cause the battery to generate smoke or burst into flame.
Do not use an abnormal battery!
If the battery pack emits a bad odour, appears to have different coloring, is deformed,
or seems abnormal for any other reason, remove it from the charger or operating
equipment and do not use it. The battery may generate heat or smoke, rupture, or
burst into flame.
CONTENTS
PREPARATION................................................................................................. 1
Supplied Accessories........................................................................ 1
INSTALLING THE BATTERY PACK........................................................... 2
INSTALLING ALKALINE BATTERIES......................................................... 2
INSTALLING THE BELT CLIP..................................................................... 3
CHARGING THE PB-45L BATTERY PACK................................................ 4
CONNECTING TO A CIGARETTE LIGHTER SOCKET............................. 5
CONNECTING TO A REGULATED POWER SUPPLY.............................. 6
CONNECTING TO A PC............................................................................. 7
CONNECTING TO AN Extanal GPS unit or Weather Station..... 7
GETTING ACQUAINTED.................................................................................. 8
Key AND CONTROL KNOB Operations............................................... 8
Display.................................................................................................... 12
BASIC OPERATIONS..................................................................................... 14
Switching THE Power ON/ OFF........................................................ 14
Adjusting the Volume...................................................................... 14
ADJUSTING THE SQUELCH.................................................................... 15
SELECTING Dual band mode/ single band MODE....................... 16
SELECTING A frequency band........................................................ 16
Selecting an Operating mode...................................................... 17
Frequency Direct Entry................................................................. 19
Transmitting........................................................................................ 20
BackLight.............................................................................................. 21
MONITOR.................................................................................................. 21
Function Select mode..................................................................... 22
SetuP OPERATION................................................................................. 22
MENU MODE.................................................................................................. 23
Menu Access........................................................................................ 23
Menu Configuration......................................................................... 24
Character Entry............................................................................... 34
OPTIONS........................................................................................................ 36
MAINTENANCE.............................................................................................. 37
GENERAL INFORMATION....................................................................... 37
SERVICE................................................................................................... 37
SERVICE NOTE........................................................................................ 37
CLEANING................................................................................................ 37
TROUBLESHOOTING............................................................................... 38
SPECIFICATIONS........................................................................................... 42
For a detailed explanation on transceiver operation, refer to the PDF file supplied
on the CD-ROM.
Operation
File name
CONTENTS
00-CONTENTS-E.pdf
OPERATING THROUGH REPEATERS
01-REPEATER-E.pdf
MEMORY CHANNELS
02-MEMORY CHANNEL-E.pdf
SCAN
03-SCAN-E.pdf
CTSSS/ DCS/ CROSS TONE
04-CTCSS_DCS_CROSS TONE-E.pdf
DUAL TONE MULTI-FREQUENCY (DTMF)
05-DTMF-E.pdf
EchoLink
06-EchoLink-E.pdf
®
OTHER OPERATIONS
07-OTHER OPERATIONS-E.pdf
GPS OPERATION
08-GPS-E.pdf
PACKET OPERATION
09-PACKET-E.pdf
APRS® OPERATION
10-APRS-E.pdf
TRANSCEIVER RESET
11-RESET-E.pdf
SKY COMMAND
12-SKY COMMAND (K TYPE)-E.pdf
WEATHER ALERT (K TYPE MODELS ONLY)
13-WEATHER ALERT (K TYPE)-E.pdf
Note: The Operations file is available in PDF file format. To read the file, you must use
Adobe® Reader®.
vi
PREPARATION
Supplied Accessories
After carefully unpacking the transceiver, identify the items listed in the table
below. We recommend you keep the box and packaging for shipping.
Item
Quantity
Antenna
Li-ion Battery Pack
AC adapter
AC power cable
Belt hook
USB cable
Warranty Card
Instruction manual
CD-ROM (For a detailed explanation on transceiver operations)
Installing the Antenna
Hold the supplied antenna by its base, then screw it into the connector on the top
panel of the transceiver until secure.
INSTALLING THE BATTERY PACK
Note: Because the battery pack is provided uncharged, you must charge the battery pack before
using it with the transceiver. To charge the battery pack, refer to “CHARGING THE PB-45L
BATTERY PACK ” {page 4}.
1 Unlock (open) the safety catch located at the bottom of the battery pack.
2 Match the guides of the battery pack with the corresponding grooves on the
upper rear of the transceiver, then firmly press the battery case to lock it in
place.
3 Flip the safety catch into place to prevent accidentally pressing the release
latch and removing the battery pack.
4 To remove the battery pack, lift the safety catch, then press the release latch to
unlock the battery pack. Lift the battery pack away from the transceiver.
INSTALLING ALKALINE BATTERIES
1 To open the optional BT-15 battery case lid, insert your thumb or finger into
the hole on the top of the battery case, then pull the cover up.
2 Insert (or remove) six AAA (LR1) Alkaline batteries.
•
Be sure to match the battery polarities with those marked in the bottom of
the battery case.
3 Align the two tabs at the bottom of battery case, then close the cover until the
locking tabs on top click.
4 To install the battery case onto (or remove it from) the transceiver, follow steps
1 to 3 of “INSTALLING THE BATTERY PACK”.
Note:
u Do not use Manganese batteries or Rechargeable batteries in place of Alkaline batteries.
u Always replace all batteries at the same time. Mixing old and new batteries or mixing types
(such as Alkaline with zinc carbon) will reduce the overall performance and could cause
leakage or rupture.
u Remove all batteries from the case when it is not expected to be in use for several months.
u The voltage of new Alkaline batteries varies slightly, depending on the manufacturer. Thus, the
high battery power indicator may not appear even though new Alkaline batteries are installed.
u To lift the battery pack safety catch, use a piece of hardened plastic or metal, such as a
screwdriver, that is no more than 6 mm wide and 1 mm thick. It is imperative that you place the
implement under only the lip of the safety catch so that you do not damage the release latch.
INSTALLING THE BELT CLIP
If desired, you can install the supplied belt clip to the transceiver.
1 Loosely insert the two supplied screws into the holes on the back panel of the
transceiver.
2 Slide the belt hook into position, under the screws.
3 Tighten the screws until secure.
Note: When the belt hook is not attached to the transceiver, remove the screws from the
transceiver to avoid scratching other materials.
CHARGING THE PB-45L BATTERY PACK
The battery pack can be charged after it has been installed onto the transceiver.
(The battery pack is provided uncharged for safety purposes.)
1 Confirm that the transceiver power is OFF.
•
While charging the battery pack, leave the transceiver power OFF.
2 Insert the charger plug into the DC IN jack of the transceiver.
To AC outlet
DC-IN jack
Chager
3 Plug the charger into an AC wall outlet.
•
Charging starts.
4 It takes approximately 12 hours to charge an empty PB-45L Li-ion battery
pack. After 12 hours, remove the charger plug from the transceiver DC IN
jack.
5 Unplug the charger from the AC wall outlet.
Note:
u Never leave the battery pack in direct sunlight.
u The transceiver becomes warm while charging the battery pack.
u While the battery pack is charged, the ambient temperature must be within 0°C ~ 40°C (32°F ~
104°F). Otherwise, charging does not start. If the transceiver senses that the temperature is
more than 60°C (140° F) during charging, the transceiver stops charging.
u Before recharging the battery pack, use the battery pack until the transceiver stops receiving.
u Do not plug the charger into the DC IN jack for more than 24 hours.
u Unplug the charger as soon as possible after the charging period is over.
u After the battery pack is charged, do not unplug and plug the charger into the AC outlet again.
Unpluging the charger will reset the charging timer and the battery pack will be charged again.
This could result in over-charging.
u If the battery pack is recharged repeatedly before the battery pack is not fully used, the memory
effect (the battery pack will not allow the charger to recharge the battery to more than a certain
voltage level) may occur. In this case, turn the transceiver ON until it stops receiving in order
to discharge the battery pack, then recharge the battery pack as normal.
u If the battery pack is not used for a long time, the battery pack capacity temporarily decreases.
In this case, charge the battery and use the battery pack until the transceiver stops receiving.
Repeat this procedure several times. The battery pack should recover its capacity.
u If the charger is plugged into the DC IN jack before the battery pack is attached, turn the
transceiver power ON and then OFF again to initiate charging.
u Exceeding the specified charge period shortens the useful life of the PB-45L battery pack.
u The provided charger is designed to charge only the PB-45L battery pack. Charging other
models of battery packs may damage the charger and battery pack.
u Do not transmit while charging.
u When not in use, store the battery pack in a cool and dry place.
u Before charging the battery pack, ensure that the safety catch is firmly closed.
u Attention should be drawn to the environmental aspects of battery disposal.
CONNECTING TO A CIGARETTE LIGHTER SOCKET
To connect the transceiver to the cigarette lighter socket in your vehicle, use an
optional PG-3J Cigarette Lighter cable.
When the PG-3J is connected to the cigarette lighter plug, the transceiver
automatically starts charging the PB-45L battery pack. While you operate the
transceiver, it charges the PB-45L battery pack in the background.
To connect with an external 24 V power source via a DC-DC converter, only use the optional PG-3J
Cigarette Lighter cable.
Using the PG-2W DC cable in this situation may cause a fire.
DC-DC Converter
24V
12V
PG-3J
Socket
24V
12V
PG-3J
DC-DC Converter
24V
12V
PG-2W
Note:
u Do not use the PG-2W to connect directly to a vehicle battery (12 V). Extensive voltage could
result in damaging the transceiver.
u If the input voltage exceeds approximately 16.5 V, warning beeps sound and “DC ERR”
appears.
CONNECTING TO A REGULATED POWER SUPPLY
To connect the transceiver to an appropriate regulated DC power supply, use an
optional PG-2W DC cable.
1 Confirm that the power of both the transceiver and the DC power supply is
OFF.
2 Connect the optional PG-2W DC cable to the DC power supply; the red lead to
the positive (+) terminal, and the black lead to the negative (–) terminal.
Fuses (4 A)
3 Connect the barrel plug on the DC cable to the DC IN jack of the transceiver.
•
While a DC power supply is connected with the DC IN jack, the transceiver
automatically initiates charging the PB-43N Ni-MH battery pack.
Note:
u If the DC power supply voltage is below 12.0 V DC, you may not be able to charge the PB-45L
battery pack.
u The supply voltage must be between 12.0 V and 16.0 V to prevent damaging the transceiver. If
the input voltage exceeds approximately 16.5 V, warning beeps sound and “DC ERR” appears.
Remove the DC IN jack plug immediately.
u If the DC power supply voltage is above 14.5 V DC and “” (High Power) is selected, the “” icon
blinks and the output power is gradually reduced to “” level (Medium Power) {page 95}.
CONNECTING TO A PC
The USB connector allows you to directly connect to a computer by using a
supplied USB. You must use the ARUA-10 software to control the USB audio
system line of the PC, available at:
http://www.kenwood.com/i/products/info/amateur/software_download.html
PC
USB terminal
Supplied USB cable
CONNECTING TO AN Extanal GPS unit or Weather Station
The GPS jack on this transceiver accepts a 2.5 mm (1/10") 3-conductor plug. If
necessary, use the cable (service part: E30-3400-XX) to modify the cable end of
extanal GPS receiver or Weather Station.
Extanal GPS receiver
Weather Station
COM terminal
RXD
TXD
GND
•
White
(to DATA IN on GPS/ WX)
Red
(to DATA OUT on GPS/ WX)
Shield
(to GND on GPS/ WX)
Use a GPS receiver which conforms to the NMEA-0183 format and is compatible with
RS-232C signal polarity output at the below mentioned levels.
[Low level: less then +0.5 V / High level: more then +3 V]
You cannot use GPS receivers with USB-type connections.
GETTING ACQUAINTED
Key AND CONTROL KNOB Operations
Press [ ] to turn the transceiver power ON and OFF.
Tuning Control
Rotate the Tuning control to select an operating frequency, Memory channel,
Menu number, setting value and change the scan direction, etc.
VOL Control
Rotate the VOL control to adjust the speaker volume.
[PTT]
Press and hold [PTT], then speak into the microphone to transmit.
[LAMP]
Press [LAMP] to illuminate the display and keys.
Press [F], [LAMP] to keep the light ON continuously.
[MONI]
Press and hold [MONI] to unmute the speaker in order to monitor signals.
Release [MONI] to return to normal operation.
[
], [ ]
Press [ ] or [ ] to select an operating frequency, Memory channel, Menu
number, setting value or to change the scan direction, etc.
The [ ]/ [ ] keys function in the exact same way as the Tuning control.
These keys change frequencies, memory channels, or other selections,
depending on the current transceiver mode.
OK]
Press [ OK] to move to the next step or to complete the setting in various
selection modes such as Function Select or Menu mode.
[ESC
Press [ESC ] to move back to the previous step or to quit the setting in
various selection modes such as Function Select or Menu mode.
[A/B]
Press [A/B] to select operation band A or B.
Press [F], [A/B] to select a frequency band.
[MENU]
Press [MENU] to enter Menu mode.
Press [F], [MENU] to cycle the transmit output power between: High Power
–> Low Power –> Economic Low Power.
[F]
Press [F] to enter Function mode.
Press [F] (1s) to turn the transceiver key lock function ON and OFF.
[VFO]
Press [VFO] to enter VFO mode, then press [
control to select an operating frequency.
]/[ ] or rotate the Tuning
Press [F], [MENU] to copy the current Memory channel or Call channel to the
VFO (memory shift).
[MR]
Press [MR] to enter Memory Channel mode, then press [
Tuning control to select a Memory channel.
]/[ ] or rotate the
Select a Memory channel, then press [F], [MR] to store the current operating
frequency in the Memory channel.
[CALL]
Press [CALL] to select the Call channel.
Press [F], [CALL] to store the current operating frequency to the Call channel.
12 Keypad
[MARK] (1)
Press [MARK] to display the Mark Way point list .
Press [MARK] (1s) to enter the Mark Way point registration mode .
Press [F], [MARK] to turn the internal GPS function ON or OFF.
[TNC] (2)
Press [TNC] to turn the built-in TNC ON and the APRS (or NAVITRA) mode
ON.
•
•
•
Each time you press [TNC], the mode cycles through the following: APRS (or
NAVITRA) mode ON >> PACKET mode ON >> TNC OFF.
When the built-in TNC turns on, “OPENING TNC” appears on the display.
When “OPENING TNC” appears on the display, the mode cannot be changed.
Press [F], [TNC] to turn the Tracking Log function ON or OFF .
[POS] (3)
Press [POS] to display your “My position” (using the internal GPS) or to enter
the Position registration mode (not using the internal GPS) .
Press [F], [POS] to enter the My Weather mode .
[MSG] (4)
Press [MSG] to display the Message list .
Press [F], [MSG] to enter the New Message input mode .
10
[LIST] (5)
Press [LIST] to display the Station list .
Press [F], [LIST] to display the DX Cluster list .
[BCON] (6)
Press [BCON] to enter the Beacon Transmit mode (TX Beacon method is
Manual) or turn the Beacon function ON or OFF (TX Beacon method is other
then Manual) .
Press [F], [BCON] to enter the Quick Beacon mode .
[REV] (7)
Press [REV] to turn the Reverse function ON or OFF.
Press [REV] (1s) to turn the Automatic Simplex Checker ON.
Press [F], [REV] to enter the Vice Alert function setup mode .
[TONE] (8)
Press [TONE] to turn the Tone function ON.
•
Each time you press [TONE], the function cycles through the following: Tone ON
>> CTCSS ON >> DCS ON >> Cross Tone ON >> OFF.
Press [F], [TONE] to enter the Tone frequency, CTCSS frequency, DCS code,
or Cross Tone setup mode.
Press [F], [TONE] (1s) to start the Tone frequency ID, CTCSS frequency ID,
or DCS code ID scan.
[PF] (9)
Press [PF] to activate its programmable function. The default function is
“Weather Channel” (TH-D72A)/ “Memory Name <-> Frequency” (TH-D72E).
[MHz] ( )
Press [MHz] to enter the Offset Direction selection mode.
•
Each time you press [MHz], the offset direction cycles through the following: plus
(+) direction –> minus (–) direction –> –7.6 MHz (TH-D72E only) –> OFF.
Press [MHz] (1s) to start the MHz scan.
Press [F], [MHz] to enter Offset Direction setup mode.
[DUAL] (0)
Press [DUAL] to switch the Single band mode and Dual band mode.
Press [F], [DUAL] to turn the Full duplex function ON or OFF.
[ENT] (#)
Press [ENT] to enter Frequency or Channel number entry mode.
Press [F], [ENT] to enter Frequency step setup mode.
11
Display


Indicator
Description
Appears while using Economic low output power.
Appears while using Low output power.
Appears while using High output power.
Appears when the Beacon type is set to “APRS”.
Appears when the Beacon type is set to “NAVITRA”.
Appears while using Packet mode.
Appears when the packet transfer rate is set to 1200 bps.
Appears when the packet transfer rate is set to 9600 bps.
Appears when a message is received.
Appears while in Stand-by (Packet mode)
Appears while Connected (Packet mode)
Appears when the Beacon function is ON.
Appears when the external GPS is ON.
Blinks while positioning.
Appears when the internal GPS is ON.
Blinks while positioning.
Appears while the internal GPS save mode is activated.
Appears when the internal GPS and Weather Instrument is
ON.
Performs as an S meter when receiving a signal and displays
the selected power level while transmitting.
12
Indicator
Description
Appears when the Tone function is ON.
Appears when the CTCSS function is ON.
Appears when the DCS function is ON.
Appears when the Cross tone setting is “TONE/CTCSS”.
Appears when the Cross tone setting is “DCS/CTCSS”.
Appears when the Cross tone setting is “TONE/DCS”.
Appears when the Cross tone setting is “DCS/Off”.
Appears when Voice Alert is set to “ON”.
Appears when Voice Alert is set to “RX ONLY”.
Appears when the Shift function is set to plus.
Appears when the Shift function is set to minus.
Appears when the Shift function is set to -7.6 MHz.
Appears when the Reverse function is ON.
Appears when the ASC function is ON.
Blinks when the ASC function is performing an OK check.
Appears while in Duplex mode.
Appears while in AM mode.
Appears while in Narrow FM mode.
Appears when the VOX function is ON.
Appears when the Key Lock function is ON.
Displays the operating frequency.
Appears while using the Internal data band.
Appears when the selected channel is not registered while in
Memory Input mode.
Appears when the selected channel is registered while in
Memory Input mode.
Displays the Memory channel number.
Appears when the Memory Channel Lockout function is ON.
Appears when Weather Alert is ON.
Blinks when receiving a signal. (TH-D72A only)
13
BASIC OPERATIONS
Switching THE Power ON/ OFF
Press the [ ] switch to switch the transceiver ON.
•
The power on message momentarily appears on the display.
•
If the transceiver power on password has been activated {Menu No.100}, you must first
enter your password before you can operate the transceiver.
Press the [ ] switch again to switch the transceiver OFF.
Adjusting the Volume
Rotate the VOL control of your selected band clockwise to increase the volume
and counterclockwise to decrease the volume.
Note: Some functions of this transceiver, such as the beep, have their own volume settings.
Adjust those settings to your desired values.
14
ADJUSTING THE SQUELCH
Squelch is used to mute the speaker when no signals are present. With the
squelch level set correctly, you will hear sound only while actually receiving a
signal. The higher the squelch level selected, the stronger the signals must be in
order to hear them.
1 Press [F], [MONI].
•
The squelch level appears on the display.
2 Press [ ]/[ ] or rotate the Tuning control of your selected band, when no
signals are present, and select the squelch level at which the background
noise is just eliminated.
Selecting AN OPERATION BAND
Press [A/B] to select operating band A or B.
15
SELECTING Dual band mode/ single band MODE
You can switch the transceiver between dual band operation and single band
operation.
1 Select your desired band (A or B).
2 Press [DUAL].
•
Each time you press [DUAL], the transceiver switches between Single band
mode and Dual band mode.
Dual band mode:
Single band mode (band A only):
Single band mode (band B only):
SELECTING A frequency band
You can change the default frequency bands for bands A and B.
1 Select your desired band (A or B).
2 Press [F], [A/B].
•
•
•
•
•
Each time you press [F], [A/B], you cycle to the next frequency band.
When masking a band, you are restricted to using only the selectable band.
When receiving 2 signals on the same band, the image interference, sensitivity,
etc., performance will decrease.
Band A: 144 >> 430/440 (MHz).
Band B: 118 >> 144 >> 300 >> 430/440 (MHz).
Note: The TH-D72E uses the 430 MHz band and the TH-D72A uses the 440 MHz band.
16
Frequency ranges:
•
•
•
•
118 MHz: 118 ~ 135.995 MHz
144 MHz: 144 ~ 173.995 MHz
300 MHz: 320 ~ 399.995 MHz
430/440 MHz: 430 ~ 523.995 MHz
Selecting an Operating mode
There are 3 operating modes available to choose from: VFO mode, Memory
Channel mode, and Call Channel mode.
VFO Mode
VFO mode allows you to manually change the operating frequency.
1 Press [VFO] to enter VFO mode.
2 Rotate the Tuning control to select your desired operating frequency.
•
•
•
You can also select a frequency by using the [ ]/[ ] keys.
The default step frequency for the Tuning control varies according to the model and
operating band:
Model
144 MHz
430/440 MHz
TH-D72A
5 kHz
25 kHz
TH-D72E
12.5 kHz
25 kHz
To adjust the frequency by a larger amount, press [MHz] to enter MHz mode, then
rotate the Tuning control to adjust the frequency in steps of 1 MHz. Press [MHz]
again to exit MHz mode and adjust the frequency using the normal step frequency.
17
Memory Channel Mode
Memory Channel mode allows you to quickly select a frequently used frequency
and related data which you have saved in the transceiver memory.
1 Press [MR] to enter Memory Channel mode.
•
The Memory channel number appears on the display.
2 Rotate the Tuning control to select your desired Memory channel.
•
You can also select a Memory channel by using the the [
]/[
] keys.
Call Channel Mode
Call Channel mode allows you to quickly select a preset channel to allow
immediate calls on that frequency. The Call channel can be conveniently used as
an emergency channel within your group.
1 Select your desired band (A or B).
•
The Call channel has a dedicated frequency for both bands A and B. The
default frequency for band A is 144 MHz. The default frequency for band B is
430/440 MHz.
2 Press [CALL] to enter Call Channel mode.
•
18
“C” appears on the display.
Frequency Direct Entry
If the desired operating frequency is far from the current frequency, using the
keypad is the quickest way to change the frequency.
1 Press [A/B] to select band A or B, then press [VFO] or [CALL].
2 Press [ENT].
•
The Direct Frequency Entry display appears.
3 Press the number keys ([0] ~ [9]) to enter your desired frequency.
4 To set the entered frequency, press [ENT] or [VFO].
•
•
•
•
Pressing [ENT] before entering all of the digits will set the remaining digits to 0.
Pressing [VFO] before entering all of the digits will leave the remaining digits at their
previous values.
Entering all digits for a frequency will automatically set the frequency without
pressing [ENT] or [VFO].
If you need to only change the MHz digit, press [MHz], then enter the new value.
19
Transmitting
1 Select your desired band and frequency/channel.
2 Press and hold the microphone [PTT] switch and speak into the microphone to
transmit.
•
The TX-RX LED lights red for the selected transmit band and the RF power meter
appear on the display. The RF power meter shows the relative transmit output
power.
•
“H”, “L”, or “EL” appear on the display, depending on the output power you have
selected.
Speak into the microphone in your normal voice, while keeping the microphone
approximately 5 cm (2 inches) from your mouth. Speaking too close to the
microphone or too loudly may increase distortion and reduce intelligibility of your
signal at the receiving station.
•
3 When you finish speaking, release the [PTT] switch.
When the transceiver overheats because of ambient high temperature
or continuous transmission, the protective circuit may function to lower the
transmit output power.
Note:
Selecting an Output Power
Selecting a low transmit power is a wise method to reduce battery consumption, if
communication is still reliable. You can program separate transmit power settings
for band A and B.
Press [F], [MENU] to select high (default), low, or economic low power (lowest).
•
20
“H”, “L”, or “EL” appears to show the current selection.
BackLight
Press [LAMP] to illuminate the display and keys.
•
•
•
If no other key is pressed, the light turns OFF approximately 5 seconds after releasing
[LAMP].
Press any key (including [PTT]) other than [LAMP] while the display and keys are lit to
restart the 5-second timer.
Press [LAMP] while the display and keys are lit to immediately turn the light OFF.
Press [F], [LAMP] to keep the light ON continuously.
•
The light remains ON until you press [F], [LAMP] again.
Note: You can set the Display lighting time in Menu No. 101.
MONITOR
When you are receiving while the squelch function is ON, weak signals may
become intermittent.
If the CTCSS or DCS function is ON, you may want to disable the squelch
function temporarily to monitor the current channel activities.
1 Press and hold [MONI].
•
The speaker is unmuted and you can monitor the signals.
2 Release [MONI] to return to normal operation.
21
SETUP OPERATION
Function Select Mode
Press [F] to enter Function Select mode. In this mode you can scroll F–0 through
F–# by pressing [ ]/[ ]. After accessing the desired function, press [ OK],
then press [ ]/[ ] to select the desired parameter.
Pressing [F], [0] ~ [9] or [ ], [#] is a much simpler method. For example,
pressing [F], [8] switches the Tone function ON or OFF. (Refer to the keypad
explanations on pages 10 ~ 11.)
Note: You can verify the battery capacity while in Function Select mode.
Full
Medium
Low
Very Low (recharge)
Menu Mode
Press [MENU] to enter Menu mode. In this mode you can access the desired
menu item by pressing [ ]/[ ] and [ OK] or entering digits directly from the
keypad (0 ~9, A, B, C, D, E ( ),and F (#) only). For further information, refer to
“MENU MODE” {page 23}.
22
MENU MODE
Many functions on this transceiver are selected or configured through the Menu
instead of physical controls. Once you become familiar with the Menu system,
you will appreciate the versatility it offers.
Menu Access
1 Press [MENU] to access the Menu.
•
The setup category name appears on the display.
2 Press [
]/[ ] or rotate the Tuning control to select your desired category.
3 Press [ OK] to set the category.
•
The Menu name and number appear on the display.
4 Press [
]/[ ] or rotate the Tuning control to select your desired Menu.
5 Press [ OK] to set the Menu.
6 Press [
Menu.
]/[ ] or rotate the Tuning control to select your desired value for the
7 Press [ OK] to set the selected value.
8 Repeat steps 2 to 7 to set up additional Menus.
9 Press [MENU] to exit Menu mode.
23
Menu Configuration
RADIO - Display
No.
Display
100
Power-on Msg
101
Lamp Time
102
Contrast
Description
Setting Values
Power-on message edit
Up to 8 characters
Display lighting time
2 ~ 5 ~ 10 sec
Display contrast
Level 1 ~ 8 ~ 16
RADIO - Battery
No.
Display
Description
Setting Values
110
Batt. Saver
Battery saver time
Off/ 0.2/ 0.4/ 0.6/ 1.0/ 2.0/ 3.0/
4.0/ 5.0 sec
111
APO
Auto power off time
Off/ 15/ 30/ 60 min
112
Battery Type
Battery type select
Lithium/ Alkaline
RADIO - Beep
No.
120
Display
Key Beep
Description
Key Beep sound
Setting Values
RADIO & GPS/ RADIO Only/
GPS Only/ Off
RADIO - TX/RX
No.
Display
130
Prog. VFO
Programmable VFO setup
Varies with the selected
frequency band
131
Modulation
Modulation/demodulation mode
AM/ FM/ NFM
132
VHF AIP
VHF band AIP
Off/ On
133
UHF AIP
UHF band AIP
Off/ On
134
VOX
VOX on/off
Off/ On
135
VOX Gain
VOX gain level
Gain 1 ~ 4 ~ 9
136
VOX Delay
VOX delay time
250/ 500/ 750/ 1000/ 1500/
2000/ 3000 ms
137
VOX on Busy
VOX on busy
Off/ On
138
Beat Shift
Beat shift
Type 1 ~ 8
139
TX Inhibit
TX inhibit
Off/ On
13A
Balance
Band A/B volume balance
5 step
13B1
WX Alert
Weather alert
Off/ On
13C1
Auto WX Scan
Auto weather channel scan time
Off/ 15/ 30 / 60 min
24
Description
Setting Values
RADIO - Memory
No.
Display
140
Name
141
Name <> Freq
142
Lockout
143
Description
Setting Values
Memory channel name input
Up to 8 characters
Name display select
Name/ Freq
Memory channel lockout
Off/ On
Recall Metho
Memory channel recall method
All Bands/ Current Band
144
Group Name
Memory group name input
Up to 8 characters
145
Group Link
Memory group link registration
Up to 10 digits (0 ~ 9)
146
EchoLink Mem
EchoLink memory setup
Up to 8 characters for
EchoLink memory name
Up to 8 digits for DTMF code
RADIO - Scan
No.
Display
Description
Setting Values
150
Scan Resume
Scan resume method
Time/ Carrier/ Seek
151
Time Restart
Time operate restart time
1 ~ 5 ~ 10 (sec)
152
Car. Restart
Carrier operate restart time
1 ~ 2 ~ 10 (sec)
RADIO - Repeater
No.
Display
Description
Setting Values
160
Offset Freq
Offset frequency
–
161
Auto Offset
Auto repeater offset
Off/ On
162
CALL Key
CALL key function
Call/ 1750Hz
163
1750Hz Hold
1750Hz Hold
Off/ On
RADIO - DTMF
No.
Display
170
Memory
171
Description
Setting Values
DTMF memory
Up to 8 characters for DTMF
memory name
Up to 16 digits for DTMF code
Speed
DTMF memory transmission speed
50/ 100/ 150 ms
172
Pause
DTMF pause code time
100/ 250/ 500/ 750/ 1000/
1500/ 2000 ms
173
Hold
Hold
Off/ On
25
RADIO - Lock
No.
Display
Description
Setting Values
180
Keys & Freq
Key lock type
Key Lock/ F.Lock/ Key &
F.Lock
181
DTMF Keys
DTMF key lock
Off/ On
182
Mic PF Keys
Mic PF key
Off/ On
RADIO - Auxiliary
No.
Display
Description
Setting Values
190
PF Key
PF key programmable function
value
191
Mic PF1
Microphone PF1 key
programmable function value
192
Mic PF2
Microphone PF2 key
programmable function value
193
Mic PF3
Microphone PF3 key
programmable function value
194
Date
Date
195
Time
Clock time
196
Time Zone
Time zone
+ 14:00 ~ UTC ~ − 14:00
197
Packet Band
Internal TNC data band type
(PACKET)
A-BAND/ B-BAND/
A:TX B:RX/ A:RX B:TX
198
Cursor Shift
Cursor Shift
Off/ 1/ 1.5/ 2 sec
199
Reset
Reset
VFO Reset/ Partial Reset/
Full Reset
19A
Power-on PWD
Power on password
Off/ On
See explanation
See explanation
GPS - Int. GPS
No.
Display
200
Operating Mode
201
202
26
Description
Setting Values
Internal GPS operating mode
Normal/ GPS Only
Batt. Saver
Battery saver time
Off/ 1/ 2/ 4/ 8/ Auto
PC Output
GPS data output to PC
Off/ On
GPS - Setup
No.
Display
210
Datum
211
Sentence
212
SBAS
Description
Setting Values
Datum
WGS-84/ TOKYO
Sentence
$GPCGA/ $GPGLL/
$GPRMC/ $GPVTG/
$GPZDA/ $GPGSA/ $GPGSV
Satellite base augmentation
system
Off/ On
GPS - Track Log
No.
Display
220
Clear All Data
221
Wrap When Full
Description
Setting Values
Clear all data
Yes/ No
Wrap when memory full
Off/ On
GPS - Log Setup
No.
Display
230
Record Method
231
232
Description
Setting Values
Record method
Time/ Distance/ Beacon
Interval
Interval time
2 ~ 1800 sec
Distance
Distance
0.01 ~ 9.99 (mi/ km/ nm)
GPS - Target Pt.
No.
240
Display
Description
Setting Values
Number select
1~5
241
Name
Name entry
Up to 8 characters
242
N (S)
Latitude entry
−
243
E (W)
Longitude entry
−
APRS - Basic Set
No.
Display
Description
Setting Values
300
My Callsign
Call sign entry
Up to 9 characters
301
Beacon Type
Beacon type
APRS/ NAVITRA
302
APRS Lock
APRS lock
Off/ On/ On & PTT
27
APRS - Int. TNC
No.
Display
Description
Setting Values
310
Data Band
Internal data band type
A-Band/
B-Band/
TX:A RX:B/
RX:A TX:B
311
Data Speed
Data communications speed
1200/ 9600 bps
APRS - Int. TNC2
No.
Display
320
DCD Sense
321
TX Delay
Description
Setting Values
DCD sense type
D or RxD Band/ Both Bands/
Ignore DCD
TX delay time
100/ 150/ 200/ 300/ 400/ 500/
750/ 1000 ms
APRS - COM Port
No.
Display
330
Baud Rate
331
Input
332
Output
Description
Setting Values
COM port Baud rate speed
2400/ 4800/ 9600 bps
COM port input type
Off/ GPS/ Weather
(PeetBros) / Weather (Davis)
COM port output
Off/ Waypoint
APRS - Waypoint
No.
Display
Description
Setting Values
340
Format
Way point format
NMEA/ MAGELLAN/
KENWOOD
341
Length
Way point name length
6-Char ~ 9-Char
342
Output
Way point output type
All/ Local/ Filtered
APRS - PC Port
No.
Display
350
Output
Description
COM port output
Setting Values
Off/ On
APRS - MyPosition
No.
360
Display
Description
Setting Values
Number select
1~5
361
Name
Name entry
Up to 8 characters
362
N (S)
Latitude entry
−
363
E (W)
Longitude entry
−
28
APRS - BeaconInfo
No.
Display
Description
Setting Values
370
Speed
Speed information
Off/ On
371
Altitude
Altitude information
Off/ On
372
Pos. Ambiguity
Position ambiguity mode
Off/ 1-Digit ~ 4-Digit
APRS - Comment
No.
380
Display
Description
Position Comment Position Comment
Setting Values
Off Duty/ Enroute/ In Service/
Returning/ Committed/
Special/ PRIORITY/
CUSTOM 0 ~ CUSTOM 6/
EMERGNCY!
APRS - StatusText
No.
Display
390
391
TX Rate
392
Text
Description
Setting Values
Number select
1~5
Status text TX rate
Off/ 1/1 ~ 1/8
Text
Up to 48 characters
APRS - QSY
No.
Display
Description
Setting Values
3A0
QSY in Status
QSY in Status
Off/ On
3A1
Tone/Narrow
Tone/ Narrow
Off/ On
3A2
Shift/Offset
Shift/ Offset
Off/ On
APRS - Pkt.Filter
No.
Display
3B0
Position Limit
3B1
Filter Type
Description
Setting Values
Position limit
Off/ 10 ~ 2500 (mile/ km)
Filter Type
See explanation
APRS - Icon
No.
Display
3C0
KENWOOD
3C1
Symbol
3C2
Table
Description
Setting Values
Icon
Symbol
See explanation
Table
29
APRS - TX Beacon
No.
Display
3D0
Method
3D1
Initial Interval
Description
Setting Values
Method
Manual/ PTT/ Auto/
SmartBeaconing
Initial interval time
0.2/ 0.5/ 1/ 3/ 5/ 10/ 20/ 30
min
APRS - Algorithm
No.
Display
3E0
Decay Algorithm
3E1
Prop.Pathing
Description
Setting Values
Decay algorithm
Off/ On
Proportional pathing
Off/ On
APRS - SmartBcon1
No.
Display
Description
Setting Values
3F0
Low/High Speed
Low speed/ High speed setting
Low speed: 2 ~ 5 ~ 30
Higt speed: 2 ~ 70 ~90
3F1
Slow Rate
Low speed transmission interval
time
2 ~ 30 min
3F2
Fast Rate
High speed transmission interval
time
10 ~ 120 ~ 180 sec
APRS - SmartBcon2
No.
Display
Description
Setting Values
3G0
Turn Angle
Driving direction change, minimum
value setting
5 ~ 28 ~ 90 deg
3G1
Turn Slope
Driving direction change, additional
value setting
1 ~ 26 ~ 255 (10deg/speed)
3G2
Turn Time
Minimum time delay between each
beacon transmission
5 ~ 30 ~ 180 sec
APRS - PacketPath
No.
Display
3H0
Type
3H1
Wide1-1 /
Relay /
Abbreviation
3H2
Total Hops
30
Description
Setting Values
Packet path type
New-N/ Relay/ Region/
Others
Wide1-1 / Relay / Abbreviation
Off/ On
Total Hops
1 ~ 2 ~7
APRS - Network
No.
Display
Description
Setting Values
3I0
APRS
APRS (APK003)
check
3I1
Altnet
Altnet
Up to 8 characters
APRS - WX Station
No.
Display
3J0
TX
3J1
TX Interval
Description
Setting Values
Weather TX
Off/ On
Weather TX interval time
5/ 10/ 30 min
APRS - Digipeat
No.
Display
3K0
Digipeat
Description
Digipeat function
Setting Values
Off/ On
APRS - Uicheck
No.
Display
3L0
Time
Description
UI check time
Setting Values
0 ~ 28 ~ 250 sec
APRS - Uidigipeat
No.
Display
Description
Setting Values
3M0
Uidigi
Uidigi
Off/ On
3M1
Aliases
Aliases
Up to 9 characters x 4
APRS - Uiflood
No.
Display
3N0
Uiflood
3N1
Alias
3N2
Substitution
Description
Setting Values
Uiflood
Off/ On
Alias
Up to 5 characters
Substitution
ID/ NOID/ FIRST
APRS - Uitrace
No.
Display
3O0
Uitrace
3O1
Alias
Description
Setting Values
Uitrace
Off/ On
Alias
Up to 5 characters
31
APRS - Phrases
No.
3P0
Display
User Phrase
Description
User phrases
Setting Values
Up to 32 characters x 8
phrases
APRS - Auto-Reply
No.
Display
3Q0
Reply
3Q1
Reply To
Description
Setting Values
Auto message reply
Off/ On
Reply to
−
APRS - Reply MSG
No.
Display
3R0
Text
Description
Auto message reply text
Setting Values
Up to 50 characters
APRS - Group Fltr
No.
Display
3S0
Message
3S1
Bulletin (BLN)
Description
Setting Values
Message group
Up to 9 characters x 6 codes
Bulletin (BLN) group
Up to 4 characters x 6 groups
APRS - Sound
No.
Display
Description
Setting Values
3N0
RX Beep
RX Beep
All/ All New/ Mine/ Message
Only/ Off
3N1
TX Beep
(Beacon)
TX Beep (Beacon)
Off/ On
3N2
Special Call
Special call
Up to 9 characters
APRS - Display
No.
Display
Description
Setting Values
3U0
Display Area
Display Area
Entire Disp/ Entire Always/
One Line
3U1
Interrupt Time
Interrupt Time
3/ 5/ 10 sec/ Infinite
3U2
Cursor Control
Cursor Contol
Followed/ Fixed
32
APRS - Unit 1
No.
Display
Description
Setting Values
Speed/ Distance
mi/h, mile/ km/h, km/ knots,
nm
Altitude, Rain
Altitude/ Rain
feet, inch/ m, mm
Temperature
Temperature
°F/ °C
3V0
Speed, Distance
3V1
3V2
APRS - Unit 2
No.
Display
3W0
Position
3W1
Grid format
Description
Setting Values
Position format
dd° mm. mm’/ dd° mm’ ss. s”
Grid format
Maidenhead Grid/ SAR Grid
(CONV)/ SAR Grid (CELL)
APRS - NAVITRA GP
No.
Display
Description
Setting Values
3X0
Group Mode
Group mode
Off/ On
3X1
Group Code
Group code
3 characters
APRS - NAVITRA MS
No.
3X0
Display
Message
Description
Message text
Setting Values
Up to 20 characters x 5
messages
SKY - SkyCommand
No.
Display
Description
Setting Values
500
CMD Callsign
Commander call sign
Up to 9 characters
501
TRP Callsign
Transporter call sign
Up to 9 characters
502
Tone Freq.
Tone frequency
Frequency
503
Sky Command
SKY command
Off/ Commnder/ Transporter
Available only for the TM-D72A.
Note: Default settings are subject to change.
33
Character Entry
Certain menus require you to enter characters, such as the power on message
and memory names. When character entry is required, a cursor will appear on
the display.
1 Press [ OK].
•
The cursor will blink.
2 Press [
]/[ ] or rotate the Tuning control to select your desired character.
3 Press [ OK] to set the selected character.
•
The cursor will move to the next digit.
•
•
•
You can move the cursor to the left or right by pressing [ESC ] or [ OK].
You can delete the selected character by pressing [A/B (CLR)].
Press and hold [LAMP] and then press [ ]/[ ] or rotate the Tuning control to
select your desired letter type.
4 Repeat steps 2 and 3 to enter the remaining characters.
•
Press [MENU] to exit Menu mode.
Auto Cursor Shift
Auto Cursor Shift will automatically shift the cursor to the next character after a
character has been entered. This function lets you set up the time delay after
character entry for the automatic cursor shift. If this function is set to OFF, you
must manually shift the cursor by pressing [ OK].
1 Enter Menu mode and access Menu 198.
2 Set the desired shift time to Off (manual shift), 1, 1.5, or 2 sec.
34
n Keypad Character Entry
The keypad can also be used to enter characters. Refer to the table below for
characters corresponding to keypad.
Key
Character Display (with
each press of the key)
Character Display (with each
press of the key)
Key
space
Not used
–
For a memory name, status text, and message:
Key
Character Display (with each press of the key)
Spece
Not used
’
–
”
35
OPTIONS
The following options are available for use with this transceiver:
•
•
•
•
•
PB-45L
BT-15
KSC-32
SMC-32
SMC-33
Li-ion battery pack
Battery case
Rapid charger
Speaker microphone
Speaker microphone
• SMC-34
Speaker microphone
• HMC-3(G) Headset
• KHS-21
Headset
•
•
•
•
•
•
Headset
Clip microphone
Earphone
Cigarette lighter cord
DC cable
DC Power Supply
KHS-29F
EMC-7
HS-9(G)
PG-3J
PG-2W
PS-60
Note: Optional accessories for use with this transceiver may change, post-production. (New
options may become available and/or current options may be discontinued.) Please refer to the
options catalog(s) for applicable transceivers.
Memory control program MCP-4A
The following functions can be set only by using the MCP-4A software:
•
•
•
SQC active condition
Input/output level (DATA terminal)
10 MHz mode selection
•
Power on password value
Using the MCP-4A software, you can:
•
•
•
•
View memory channel groups
Name memory groups
Save/load settings
Read exported TravelPlus for Repeaters™ files issued from the ARRL™				
(There are some version restrictions; refer to the help text of the MCP-4A.)
Print/export memory and various settings in html
•
(TravelPlus for Repeaters is a trademark of ARRL.)
To download the MCP-4A software, go to:
http://www.kenwood.com/i/products/info/amateur/software_download.html
Note: This URL may change without notice.
Using the MCP-4A Software
1 Follow the directions of the installer to install the software.
2 Set up the PC COM port and baud rate.
3 The transceiver data is read from the MCP-4A software.
4 Select your desired settings, then write the data to the transceiver.
36
MAINTENANCE
GENERAL INFORMATION
This product has been factory aligned and tested to specification before shipment.
Attempting service or alignment without factory authorization can void the product
warranty.
SERVICE
When returning this product to your dealer or service center for repair, pack it in
its original box and packing material. Include a full description of the problem(s)
experienced. Include your telephone number along with your name and address
in case the service technician needs to contact you; if available, also include your
fax number and e-mail address. Don’t return accessory items unless you feel
they are directly related to the service problem.
You may return this product for service to the authorized Kenwood dealer from
whom you purchased it, or any authorized Kenwood service center. Please do
not send subassemblies or printed circuit boards; send the complete product. A
copy of the service report will be returned with the product.
SERVICE NOTE
If you desire to correspond on a technical or operational problem, please make
your note legible, short, complete, and to the point. Help us help you by providing
the following:
•
•
•
Model and serial number of equipment
Question or problem you are having
Other equipment in your station pertaining to the problem
Do not pack the equipment in crushed newspapers for shipment! Extensive damage may result
during rough handling or shipping.
Note:
u Record the date of purchase, serial number and dealer from whom this product was purchased.
u For your own information, retain a written record of any maintenance performed on this
product.
u When claiming warranty service, please include a photocopy of the bill of sale or other
proof-of-purchase showing the date of sale.
CLEANING
To clean the case of this product, use a neutral detergent (no strong chemicals)
and a damp cloth.
37
TROUBLESHOOTING
The problems described in this table are commonly encountered operational
malfunctions and are usually not caused by circuit failure.
Problem
Probable Cause
Corrective Action
Nothing appears on
the display when the
transceiver is switched
ON, or the display is
blinking ON and OFF.
1 The battery pack is
discharged.
1 Recharge the battery pack
or replace the battery.
2 The DC cable or
connection is bad.
2 Replace the cable.
3 The power supply
fuse is open (blown).
3 Investigate the cause for
the open fuse and replace
the fuse.
Most keys and the
Tuning control do not
function.
1 One of the Lock
functions is ON.
1 Unlock all of the Lock
functions.
2 The transceiver is
in Channel Display
mode.
2 With the transceiver
power OFF, press [PTT] +
[A/B] + Power ON to exit
Channel Display mode.
You cannot select the
exact desired frequency
using the Tuning
control.
Programmable VFO
frequency range is too
narrow.
Expand the frequency range
in Menu No. 130 (Prog.VFO).
Memory channels
cannot be selected
by turning the Tuning
control or by pressing
[ ]/[ ].
No data has been stored Store data in some Memory
in any Memory channel. channels.
The receiving sound
volume is weak even if
the signal is strong.
The receiving station
may be operating
in narrow band FM
bandwidth.
Access Menu No. 131
(Modulation) to select “NFM”.
Turning the VOL
control does not allow
you to hear audio.
The selective call
function (CTCSS or
DCS) is ON.
Turn OFF the selective call
function.
38
Problem
You cannot transmit
by pressing the PTT
switch.
Probable Cause
Corrective Action
1 You selected a
1 Select a frequency within
frequency outside the
the allowable transmit
allowable range.
frequency range.
2 You selected a
2 Select a proper offset
trasmit offset that
direction or offset
places the tranmit
frequency.
frequency outside the
limit.
3 TX inhibit is ON.
4 The battery pack
voltage is too low to
transmit.
3 Access Menu No. 139 (TX
inhibit) and select “Off”.
4 Charge or replace the
battery pack.
1 Wrong tone
frequency is
selected.
1 Select a proper repeater
access tone.
2 Wrong offset
frequency is
selected.
3 Wrong shift direction
is selected.
3 Try other shift directions.
DTMF tone cannot be
transmitted.
DTMF Lock is ON.
Access Menu No. 181 (DTMF
Keys) and select “Off”.
Repeater does not
accept your DTMF
tones.
DTMF tone
Access Menu No. 171
transmission duration is (Speed) and select “150
too short.
ms”.
You cannot transmit by
pressing [PTT].
1 You selected a
1 Select a frequency within
frequency outside the
the allowable transmit
allowable range.
frequency range.
Repeater cannot be
accessed.
Access Menu No. 160
(Offset Freq) and select
an appropriate offset
frequency.
2 You selected a
2 Select a proper offset
transmit offset that
direction or offset
places the transmit
frequency.
frequency outside the
limit.
Transceiver transmits
without pressing [PTT].
3 TX inhibit is ON.
3 Access Menu No. 139 (TX
inhibit) and select “Off”.
4 The battery pack
voltage is too low to
transmit.
4 Change or replace the
battery pack.
VOX function is ON.
Access Menu No. 131
(VOX) and select “Off”.
39
Problem
The transceiver
switches OFF for no
apparent reason.
Probable Cause
The Automatic Power
OFF (APO) function is
ON.
The Scan function does You have selected
not resume scanning
“Seek” for Menu No.
after the transceiver
150 (Scan Resume).
detects a signal.
Packet operation
results in no connects
with other stations.
1 The squelch is open.
Corrective Action
Access Menu No. 111
(APO) and select your
desired time length or
“OFF”.
Select either “Time” (TimeOperated) or “Carrier”
(Carrier-Operated) for Menu
No. 150 (Scan Resume).
1 Select the correct squelch
level so that the squelch is
opened only when signals
are present.
2 You did not select the 2 Use HBAUD command
same transfer rate as
to select the appropriate
the target station.
transfer rate.
You cannot transmit
any APRS data.
When using a GPS
receiver, you cannot
correctly transmit
position data.
1 Beacon is OFF.
1 Press [BCON] to switch
Beacon ON.
2 The squelch is open.
2 Select the correct squelch
level so that the squelch is
opened only when signals
are present.
3 The data band is
inactive.
3 If you have blanked the
data band, press [A/B] or
[DUAL] to active it.
4 The built-in TNC is
OFF.
4 Press [TNC] to switch ON
the TNC.
5 You selected Packet
mode.
5 Press [TNC] twice so that
only “
” appears.
The GPS receiver did
not yet start correct
measurement.
Before starting correct
measurement, the GPS
receiver generates a lowpitch tone every 10 seconds.
When starting correct
measurement, it generates a
high-pitch tone. (If not using
the internal GPS receiver,
press [F], [MARK] and
select “OFF”).
You cannot receive any You did not correctly
APRS data.
program a group code.
40
Access Menu 3S0 and
program “APK001”.
Problem
Probable Cause
“MCP ERR” appears on
the display. (MCP-4A
communications error)
Corrective Action
1 Loose cable
connection.
1 Ensure that the connection
between the TH-D72 and
the PC is correct.
2 Your PC may be
trying to process too
much at once.
2 Shut down other software
that you may be running.
3 There are other
reasons as to why
communications was
not possible.
3 Turn the TH-D72 power
source OFF and ON, one
time.
Concerning the received frequency display, an unmodulated signal may be
received. This is according to the set intrinsic frequency form.

VxU reception
UxV reception

(144 MHz + 45.05 MHz) x 2
–
(430 MHz - 49.95 MHz)
45.05 MHz, 49.95 MHz
(144 MHz + 45.05 MHz) x 4
–
(430 MHz - 49.95 MHz) x 2
45.05 MHz, 49.95 MHz
(430 MHz - 45.05 MHz)
–
(144 MHz + 49.95 MHz) x 2
45.05 MHz, 49.95 MHz
(430 MHz - 45.05 MHz) x 2
–
(144 MHz + 49.95 MHz) x 4
45.05 MHz, 49.95 MHz
41
SPECIFICATIONS
Specifications are subject to change without notice, due to advancements in
technology.
Guaranteed
range (TX-RX)
General
VHF Band
UHF Band
TH-D72A
144 ~ 148 MHz
438 ~ 450 MHz
TH-D72E
144 ~ 146 MHz
430 ~ 440 MHz
136 ~ 174 MHz
Band A
Frequency
range
410 ~ 470 MHz
RX
118 ~174 MHz
Band B
320 ~ 524 MHz
Mode
F1D/ F2D/ F3E
Antenna impedance
50 Ω
Operating temperature range
Rated voltage
–10°C ~ +50°C (+14°F ~ +122°F)
External power supply
(DC IN)
12.0 ~ 16.0 V (13.8 V)
Battery terminals
4.5 ~ 10.8 V (6.0 V)
Ground method
Negative
Frequency stability
Within ±5 ppm (–10°C ~ +50°C)
Receive with no signals
Battery Saver ON
TNC ON
Current
42
Approx. 115 mA
Approx. 1.6 A
Approx. 1.7 A
Transmit with H, 9.6 V
(battery terminals)
Approx. 1.6 A
Approx. 1.7 A
Transmit with H, 6.0 V
(battery terminals)
Approx. 1.3 A
Approx. 1.4 A
Transmit with L, 6.0 V
(battery terminals)
Approx. 500 mA
Transmit with EL, 6.0 V
(battery terminals)
Approx. 500 mA
With one band blanked (TNC OFF): Approx. 45 mA.
With one band blanked (TNC OFF): Approx. 25 mA.
Projections not included.
4 Antenna and belt hook included.
Average 25 mA
Transmit with H, 13.8 V
(DC IN)
Dimensions (W x H x D) 3
Weight
Approx. 90 mA
58 x 121.3 x 33.2 mm (2.28" x 4.78" x 1.31")
Approx. ??? g (?? oz)
Transmitter
RF power output
VHF Band
UHF Band
H, 13.8 V
Approx. 5 W
H, 9.6 V
Approx. 5 W
H, 6.0 V
Approx. 2.5 W
L, 6.0 V
Approx. 2.2 W
Approx. 0.5 W
EL, 6.0 V
Approx. 50 mW
Modulation
Reactance
Maximum frequency deviation
Within ±5 kHz
Spurious radiation
Less than –60 dB
Modulation distortion (300 Hz ~ 3 kHz)
Less than 3%
Microphone impedance
2kΩ
Receiver
VHF Band
Circuitry
1st IF
2nd IF
UHF Band
Double super heterodyne
Band A
49.95 MHz
Band B
45.05 MHz
Band A
450 kHz
Band B
455 kHz
Sensitivity (144, 430/440 MHz band)
Less than 0.16 µV (-16 dBµ)
Squelch sensitivity
(144, 430/440 MHz band)
Less than 0.1 µV (-20 dBµ)
Selectivity
Audio output
(10% distortion)
–6 dB
More than 11 kHz
–40 dB
Less than 30 kHz
9.6 V (battery
terminals)
More than 450 mW
6.0 V (battery
terminals)
More than 300 mW
Sensitivity (approx.) 
Frequency range
Band A
Band B
FM: 12 dB SINAD
FM: 12 dB SINAD
AM: 10 dB S/N
118 ~ 135.995 MHz
—
0.32 µV (-10 dBµ)
0.40 µV (-8 dBµ)
136 ~ 173.995 MHz
0.40 µV (-8 dBµ)
0.40 µV (-8 dBµ)
0.50 µV (-6 dBµ)
320 ~ 339.995 MHz
0.56 µV (-5 dBµ)
0.56 µV (-5 dBµ)
0.56 µV (-5 dBµ)
400 ~ 499.995 MHz
0.28 µV (-11 dBµ)
0.28 µV (-11 dBµ)
0.36 µV (-9 dBµ)
500 ~ 523.995 MHz
0.56 µV (-5 dBµ)
0.56 µV (-5 dBµ)
0.71 µV (-3 dBµ)
43
Bu ürün 26891sayılı Resmi Gazete’de yayımlanan Elektrikli ve Elektronik Eşyalarda
Bazı Zararlı Maddelerin Kullanımının Sınırlandırılmasına Dair Yönetmeliğe uygun
olarak üretilmiştir.
This product complies with Directive, Number 26891 regarding "REGULATION
ON THE RESTRICTION OF THE USE OF CERTAIN HAZARDOUS
SUBSTANCES IN ELECTRICAL AND ELECTRONIC EQUIPMENT".

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Instance ID                     : uuid:fc0598b5-9bb4-11df-aa66-00145163edf6
Document ID                     : adobe:docid:indd:e25e6bc9-878f-11df-bd17-df690d6d36ba
Rendition Class                 : proof:pdf
Derived From Instance ID        : e25e6bc8-878f-11df-bd17-df690d6d36ba
Derived From Document ID        : adobe:docid:indd:d26fbce7-5ac5-11df-af84-b87295e5a1f5
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:b49ed718-7cc8-11df-a370-00145163edf6, uuid:53A5224AB9D711DB9967D59E20234CB7, uuid:53A5224AB9D711DB9967D59E20234CB7, uuid:53A5224AB9D711DB9967D59E20234CB7
Manifest Reference Document ID  : uuid:57EBE37E7EA611DFB71988BBA5A99C93, uuid:53A52247B9D711DB9967D59E20234CB7, uuid:53A52247B9D711DB9967D59E20234CB7, uuid:53A52247B9D711DB9967D59E20234CB7
Create Date                     : 2010:07:18 16:43:02+09:00
Modify Date                     : 2010:07:30 17:32:25+09:00
Metadata Date                   : 2010:07:30 17:32:25+09:00
Creator Tool                    : Adobe InDesign CS2_J (4.0.5)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 12619 bytes, use -b option to extract)
Format                          : application/pdf
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
Has XFA                         : No
Page Count                      : 54
Creator                         : Adobe InDesign CS2_J (4.0.5)