JVC KENWOOD 452500 UHF DIGITAL BASE-REPEATER User Manual TKR D710 TKR D810 K

Download:
Mirror Download [FCC.gov]
Document ID	2839858
Application ID	YLbJwb57qnzu2baLxth6BA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	18.06kB (225750 bits)
Date Submitted	2015-12-11 00:00:00
Date Available	2015-12-11 00:00:00
Creation Date	2015-10-15 10:50:47
Document Lastmod	2015-12-09 09:44:12
Document Title	TKR-D710,TKR-D810 (K)
Document Creator	Adobe InDesign CS5.5_J (7.5.3)
Document Author:	JVC KENWOOD Corporation

TKR-D710
TKR-D810
VHF DIGITAL REPEATER
UHF DIGITAL REPEATER
INSTRUCTION MANUAL
B5A-1121-00 (K)
VHF DIGITAL REPEATER/ UHF DIGITAL REPEATER
TKR-D710/ TKR-D810
INSTRUCTION MANUAL
THANK YOU!
◆ Do not install the repeater in explosive atmospheres (inflammable
gas, dust particles, metallic powders, grain powders, etc.).
We are grateful you purchased this KENWOOD repeater. We
believe this easy-to-program repeater will be highly effective in
your communications system, and will keep personnel operating
at peak efficiency.
PRECAUTIONS
•
•
•
•
•
•
•
◆ This repeater is intended for use as a fixed base station with
the antenna located outdoors on the rooftop or on an antenna
tower.
◆ This repeater is designed for a 13.6 V DC power source!
Never use a 24 V DC or higher source to power the repeater.
◆ Use only the supplied DC cord.
◆ Do not remove the ferrite core attached to the DC cord. Doing
so may cause interference with radio communications.
Do not expose the unit to rain or moisture; to prevent fire or
electric shock.
Do not open the unit under any circumstances; to avoid risk of
electric shock.
Do not expose the unit to long periods of direct sunlight, nor
place it close to heating appliances.
Do not place the unit in excessively dusty and/or humid areas,
nor on unstable surfaces.
Do not put the plastic bag used for packing of this equipment
on the place which reaches a small child's hand. It will
become a cause of suffocation if it wears flatly.
Always switch the transceiver power off before installing
optional accessories.
If you detect an abnormal odor or smoke coming from the unit,
disconnect the power from the unit immediately. Contact your
KENWOOD service center or dealer.
UNPACKING AND CHECKING EQUIPMENT
Note: The following unpacking information is for use by your
KENWOOD dealer, an authorized KENWOOD service center, or the
factory.
Carefully unpack the repeater. We recommend that you identify
the items listed in the following table before discarding the packing
material. If any items are missing or have been damaged during
shipment, file a claim with the carrier immediately.
Item
Hardware fixture
Front glass
Name plates
Cushion
Cushion
Foot
Foot
Grommet
Handle
Screws
Screws
DC cord
Lead wire with connector (15 pin)
Fuse
Instruction Manual
NOTICES TO THE USER
◆ Government law prohibits the operation of unlicensed radio
transmitters within the territories under government control.
◆ Illegal operation is punishable by fine and/or imprisonment.
◆ Refer service to qualified technicians only.
One or more of the following statements may be applicable:
FCC WARNING
This equipment generates or uses radio frequency energy. Changes
or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved by the party
responsible/JVC KENWOOD. The user could lose the authority to
operate this equipment if an unauthorized change or modification is
made.
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY
THE FCC
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can generate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
Part Number
J21-8559-XX
B10-2635-XX
B11-1259-XX
G13-1801-XX
G13-1802-XX
J02-0475-XX
J02-0492-XX
J59-0302-XX
K01-0418-XX
N30-4006-XX
N35-3006-XX
E30-3427-XX
E31-3228-XX
F05-1537-XX
B5A-1121-XX
Quantity
INSTALLATION
To install the handles onto the front panel of the repeater, align the
handles with the holes on the front panel, then secure the handles
using the supplied screws.
Please consult your dealer for installing the repeater and antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
The AMBE+2TM voice coding Technology embodied in this product
is protected by intellectual property rights including patent rights,
copyrights and trade secrets of Digital Voice Systems, Inc. This
voice coding Technology is licensed solely for use within this
Communications Equipment. The user of this Technology is
explicitly prohibited from attempting to extract, remove, decompile,
reverse engineer, or disassemble the Object Code, or in any other
way convert the Object Code into a human-readable form. U.S.
Patent Nos. #6,199,037, #6,912,495, #8,200,497, #7,970,606, and
#8,359,197.
• Consult the dealer for technical assistance.
Firmware Copyrights
The title to and ownership of copyrights for firmware embedded in
KENWOOD product memories are reserved for JVC KENWOOD
Corporation.
CONTROLS AND FUNCTIONS
■ Front Panel
d e
CH/STATUS
VOLUME
TX
BUSY
POWER
MIC
a Speaker
b CH/STATUS Display
Two 7-segment digits display the channel number, name,
or status.
c VOLUME control
Rotate to adjust the audio.
d POWER switch
e POWER indicator
Lights green when power is supplied to the DC 13.6V jack.
f MIC jack
Connect a microphone to this 8-pin modular jack.
hg
g Programmable Function keys
Press these keys to activate their programmable functions.
h BUSY indicator
Lights green while a signal is being received.
i TX indicator
Lights red while transmitting.
■ Rear Panel
a b
TX OUT
d e
REF IN
RX IN
CONTROL
I/O
FUSE
DC 13.6V
TEST/SPKR
N SYNC
a TX OUT jack
f DC 13.6V jack
Connect a TX antenna or a duplexer to this receptacle.
CONTROL I/O jack
Connect a repeater controller or a remote panel to this
DB-25 interface.
REF IN jack
This jack is currently not used.
RX IN jack
Connect an RX antenna or a duplexer to this BNC
receptacle.
FUSE
Insert 15 A blade fuse into this fuse holder.
Connect a 13.6 V DC power supply to this jack.
g N SYNC 1 / 2 jack
This jack is currently not used. Future functions include
connecting another repeater or optional device.
h TEST/SPKR jack
Test input/output jack. Connect an external speaker to this
jack. When using a Built-in speaker, connect the attached
Lead wire with connector (15 pin) to this jack.
TRANSCEIVER OPERATION (Analog mode only)
REPEATER OPERATION
■ Receive
Adjust the volume to your desired level. You may need to
readjust the volume if you are having interference while
receiving a message from your dispatcher or another member
in your fleet.
The BUSY indicator lights green while a signal is being
received.
Note:
◆ Please consult your dealer for programming the repeater.
◆ After switching the power on, the CH/STATUS display blinks for
approximately 30 seconds, until the internal circuit stabilizes. Wait
until the display remains lit, before operating.
When power is applied to the unit, the POWER indicator lights:
・ Green when using the DC jack.
The BUSY indicator lights green while receiving a signal and the
TX indicator lights red while transmitting.
■ Transmit
1 Listen to the channel before transmitting, to make sure it is
not being used.
2 Press the microphone PTT switch, then speak in your
normal speaking voice.
The TX indicator lights red while transmitting.
3 When you finish speaking, release the PTT switch.
© 2015
ADDENDUM
Terminal Description
MIC (Modular Jack)
Pin
NO.
Pin Name
Description
SpeciÞcation
I/O
Not used
̋
Power Output
13.6 V
GND
GND
NC
Not used
SB
GND
PTT
PTT Signal/
TXD2 Asynchronous Send Data
Input Impedance 22 kǣ
MICG
MIC GND
MIC GND
MIC
MIC Input
600 ǣ
HOOK
Hook Detection/
RXD2 Asynchronous Receive Data
Input Impeadance 100 kǣ
NC
Not used
Not used
̋
Notes
̋
I/O
̋
TEST/ SPEAKER CONNECTOR
Pin
NO.
Pin Name
Description
Power Output
SpeciÞcation
I/O
SB
13.6 V
SB
NC
Power Output
13.6 V
Not used
Not used
GND
GND
GND
̋
GND
GND
GND
SPG
Speaker GND
Speaker GND
NC
Not used
Not used
̋
RSSI
RSSI Signal Output
Output Level 0 or 3.3 V
SPI
Internal Speaker Input
Short with "SPO"
10
AO1
Open Collector Terminal
Allowable current value MAX 200mA
11
AO2
Open Collector Terminal
Allowable current value MAX 200mA
12
SPO
External Speaker Output
Output Level 4W (5% Distortion)
13
AO3
Open Collector Terminal
Allowable current value MAX 200mA
14
AO4
Open Collector Terminal
Allowable current value MAX 200mA
15
AO5
Open Collector Terminal
Allowable current value MAX 200mA
Notes
̋
̋
̋
Control I/O (D-SUB 25 Pin) CONNECTOR
Pin
NO.
Pin Name
Description
Not used
SpeciÞcation
I/O
Notes
̋
NC
Not used
RXD0
Asynchronius Receive Data
Conform to RS-232C standard
TXD0
Asynchronius Send Data
Conform to RS-232C standard
AI1
Programmable Function Input 1
Input Impedance 47 kǣ
AI2
Programmable Function Input 2
Input Impedance 47 kǣ
AI3
Programmable Function Input 3
Input Impedance 47 kǣ
DG
Digital GND
Digital GND
̋
NC
Not used
Not used
NC
Not used
Not used
10
NC
Not used
Not used
11
NC
Not used
Not used
12
RXG
RX Signal GND
RX Signal GND
13
SPM
Speaker Mute
Input Impedance 47 kǣ
14
BER CLK
For Bit Error Rate Clock
CMOS
15
NC
Not used
Not used
̋
16
NC
Not used
Not used
̋
17
SC
Squelch Control
Output level 0 or 5 V
18
BER DAT
For Bit Error Rate Data
CMOS
19
TXG
TX Signal GND
TX Signal GND
20
IO1
Programmable Function I/O 1
Input Impedance 47 kǣ/ Output level 0 or 5 V
I/O
21
IO2
Programmable Function I/O 2
Input Impedance 47 kǣ/ Output level 0 or 5 V
I/O
22
IO3
Programmable Function I/O 3
Input Impedance 47 kǣ/ Output level 0 or 5 V
I/O
23
IO4
Programmable Function I/O 4
Input Impedance 47 kǣ/ Output level 0 or 5 V
I/O
24
IO5
Programmable Function I/O 5
Input Impedance 47 kǣ/ Output level 0 or 5 V
I/O
25
IO6
Programmable Function I/O 6
Input Impedance 47 kǣ/ Output level 0 or 5 V
I/O
̋
̋
̋
̋
̋
̋
N SYNC 1, 2 Connector (There are two connectors)
Pin
NO.
Pin Name
Description
SpeciÞcation
I/O
Notes
N_SYNC 1_B
RS-485 DiŮrential Signal B
Conform to RS-485
I/O
Connector#1,2
N_SYNC 1_A
RS-485 DiŮrential Signal A
Conform to RS-485
I/O
Connector#1,2
N_SYNC 2_B
RS-485 DiŮrential Signal B
Conform to RS-485
I/O
Connector#1,2
N_SYNC 2_A
RS-485 DiŮrential Signal A
Conform to RS-485
I/O
Connector#1,2
RX IN
TX OUT
RX antenna terminal (BNC Receptacle)
TX antenna terminal (N Receptacle)
REF IN
Reference CLK input treminal (BNC Receptacle)
© 2015
B5K-0230-00
MANDATORY SAFETY INSTRUCTIONS TO INSTALLERS AND USERS
•
Use only manufacturer or dealer supplied antenna.
•
Antenna Minimum Safe Distance: 120 cm (4 feet), 50% duty Cycle.
•
Antenna Gain: 0 dBd referenced to a dipole.
The Federal Communications Commission has adopted a safety standard for
human exposure to RF (Radio Frequency) energy which is below the OSHA
(Occupational Safety and Health Act) limits.
•
Antenna Mounting: The antenna supplied by the manufacturer or
radio dealer must not be mounted at a location such that during radio
transmission, any person or persons can come closer than the above
indicated minimum safe distance to the antenna, i.e. 120 cm (4 feet) ,
50% duty Cycle.
•
To comply with current FCC RF Exposure limits, the antenna must be
installed at or exceeding the minimum safe distance shown above, and in
accordance with the requirements of the antenna manufacturer or supplier.
•
Vehicle installation: The antenna can be mounted at the center of a vehicle
metal roof or trunk lid, if the minimum safe distance is observed.
•
Base Station Installation: The antenna should be fixed-mounted on
an outdoor permanent structure. RF Exposure compliance must be
addressed at the time of installation.
Antenna substitution: Do not substitute any antenna for the one supplied or
recommended by the manufacturer or radio dealer.
You may be exposing person or persons to excess radio frequency radiation.
You may contact your radio dealer or the manufacturer for further instructions.
Maintain a separation distance from the antenna to person(s) of at least
120 cm (4 feet) , 50% duty Cycle.
You, as the qualified end-user of this radio device must control the exposure
conditions of bystanders to ensure the minimum separation distance (above)
is maintained between the antenna and nearby persons for satisfying RF
Exposure compliance. The operation of this transmitter must satisfy the
requirements of Occupational/Controlled Exposure Environment, for workrelated use, transmit only when person(s) are at least the minimum distance
from the properly installed, externally mounted antenna. Transmit only when
people outside the vehicle are at least the recommended minimum lateral
distance away from the antenna/vehicle.
B59-2353-10

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
Author                          : JVC KENWOOD Corporation
Create Date                     : 2015:10:15 10:50:47+09:00
Modify Date                     : 2015:12:09 09:44:12+09:00
Subject                         : B5A-1121-00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Creator                         : JVC KENWOOD Corporation
Description                     : B5A-1121-00
Title                           : TKR-D710,TKR-D810 (K)
Creator Tool                    : Adobe InDesign CS5.5_J (7.5.3)
Metadata Date                   : 2015:12:09 09:44:12+09:00
Keywords                        : 
Producer                        : iTextSharp™ 5.5.0 ©2000-2013 iText Group NV (AGPL-version); modified using iTextSharp™ 5.5.0 ©2000-2013 iText Group NV (AGPL-version)
Document ID                     : uuid:ed2c4562-4a11-47e8-8e21-6f5b5e570433
Instance ID                     : uuid:ad38aca2-6cba-497c-8386-7498fd2206aa
Page Layout                     : SinglePage
Page Count                      : 6

EXIF Metadata provided by EXIF.tools