JVC KENWOOD V2T001 USB wireless transmitter User Manual cover RX D301S J f p65

JVC KENWOOD Corporation USB wireless transmitter cover RX D301S J f p65

Users Manual

Download: JVC KENWOOD V2T001 USB wireless transmitter User Manual cover RX D301S J  f p65
Mirror Download [FCC.gov]JVC KENWOOD V2T001 USB wireless transmitter User Manual cover RX D301S J  f p65
Document ID530886
Application IDKNL0m9SnsUozvvLnF692Tg==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeYes
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize69.82kB (872713 bits)
Date Submitted2005-04-11 00:00:00
Date Available2005-04-11 00:00:00
Creation Date2005-02-23 15:05:21
Producing SoftwareAcrobat Distiller 4.0 for Macintosh
Document Lastmod2005-04-08 18:57:18
Document Titlecover_RX-D301S[J]_f.p65
Document CreatorPageMaker 6.5
Document Author: ‹Éfi„

Warnings, Cautions, and Others
Mises en garde, précautions et indications diverses
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le
coffret de l’appareil.
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.
Caution––
STANDBY/ON button!
Disconnect the mains plug to shut the power off completely. The
STANDBY/ON button in any position does not disconnect the
mains line. The power can be remote controlled.
Attention—Touche
STANDBY/ON!
Déconnectez la fiche d’alimentation secteur pour couper
l’alimentation complètement. La touche
STANDBY/ON,
dans n’importe quelle position, ne déconnecte pas le système
du secteur. L’alimentation ne peut pas être télécommandé.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Section 820-40 of the NEC which provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as
practical.
For Canada/pour le Canada
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQUAU FOND
safety_RX-D301S[J]_f.p65
CAUTION
Changes or modifications not approved by JVC could void the
user’s authority to operate the equipment.
For U.S.A
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
For U.S.A
Declaration of Conformity:
Trade Name:
JVC
Model Number:
RX-D301S/RX-D302B
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Responsible Party:
JVC Americas Corp.
Address:
1700 Valley Road, Wayne
New Jersey 07470
Telephone Number: 973-317-5000
For USB wireless transmitter
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received,
including interference that may Cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment. To maintain compliance with FCC RF
exposure compliance requirements, please avoid direct contact to the
transmitting antenna during transmitting.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
For Canada/pour le Canada
This Class B digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
For Canada/pour le Canada
Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
L’utilisation de ce dispositif est autorisée seulement aux
conditions suivantes : (1) il ne doit pas produire de brouillage
et (2) l’utilisateur du dispositif doit être prêt à accepter tout
brouillage radioélectrique reçu, même si ce brouillage est
susceptible de compromettre le fonctionnement du dispositif.
05.2.22, 16:44
USB Connection
This receiver is equipped with a USB terminal on the front panel
and a USB WIRELESS ANTENNA terminal on the rear. You can
enjoy sound reproduced through your PC with either of the
following methods:
1 connecting a USB wireless antenna (supplied) to the USB
WIRELESS ANTENNA terminal and a USB wireless
transmitter (supplied) to your PC. (USB WIRELESS)
2 connecting your PC to the USB terminal with a USB cable (not
supplied). (USB TERMINAL)
When you connect your PC for the first time, follow the procedure
below.
• Remember you cannot send any signal or data to your PC from
this receiver.
• Use USB extension cable (supplied) if it is difficult to connect
the transmitter directly to the USB connector or the transmitter
becomes obstacle to other USB connectors.
4. Turn on the receiver, then slide the USB WIRELESS
switch on the rear to “ID LEARNING,” and select the
source as “USB WIRELESS.”
When you slide the switch, the lamp in the switch starts
flashing.
5. Set the volume to minimum.
IMPORTANT:
Always set volume to “0” when connecting or disconnecting the
other equipment.
6. Press and hold ID on the transmitter to make a wireless
communication with the receiver.
When you press and hold the button, the ID lamp on the
transmitter flashes.
USB WIRELESS TRANSMITTER
IMPORTANT:
CHANNEL
• Check if your PC equipped with the CD-ROM drive is running
on Windows® 98 SE*, Windows® Me*, Windows® 2000* or
Windows® XP* and prepare its CD-ROM.
• Check your PC’s BIOS setting—whether USB is available, and
whether USB IRQ is set to “AUTO” or to available IRQ number.
Preparation
ID
POWER
ID
PLAYER
When the receiver recognizes the transmitter, the “L” and “R”
indicators (see page 16) light up on the display. The lamp on
the rear stops flashing and lights up.
7. Slide the switch on the receiver to “ON.”
• If you do not, no sound signal is transmitted to the receiver.
NOTES
1 (For USB WIRELESS)
Be sure to make this procedure after purchasing the
receiver.
1. Connect the antenna to the USB WIRELESS ANTENNA
terminal on the rear panel.
• Tighten the screw with the antenna upright.
USB wireless
antenna
(supplied)
USB WIRELESS
• The signal-reachable distance is about 30 m (100 ft.), but it may
differ depending on the operating conditions and circumstances.
• The PLAYER lamp on the transmitter keeps flashing when
starting the playback software in your PC.
• If no signals are transmitted from the transmitter for about 30
minutes, the transmitter enters “sleep” mode. The “L” and “R”
indicators go off from the display.
• Though the transmitter may become hot, it is not a malfunction.
2 (For USB TERMINAL)
1. Turn on your PC.
• If the PC has been turned on, quit all the applications now
running.
ANTENNA
ON
ID LEARNING
2. Turn on the receiver, and select the source as “USB
TERMINAL.”
3. Set the volume to minimum.
IMPORTANT:
2. Turn on your PC.
• If the PC has been turned on, quit all the applications now
running.
3. Connect the USB wireless transmitter to the USB
connector of the PC.
Before connecting the transmitter to the PC, remove the cover
of the transmitter.
When you connect the transmitter, the USB drivers are
installed. The POWER and PLAYER lamp on the transmitter
light up.
Always set volume to “0” when connecting or disconnecting the
other equipment.
4. Connect the receiver to the PC using a USB cable (not
supplied).
USB
USB wireless
transmitter (supplied)
PC
USB WIRELESS TRANSMITTER
USB cable
(not supplied)
USB WIRELESS TRANSMITTER
POWER
ID
PLAYER
• Use “USB series A plug to B plug” cable when connecting.
12
11-13D301J2.p65
12
05.2.23, 18:30
How to install the USB drivers
The following procedure is described using the English version of
WindowsR XP. If your PC is running on a different version of
operation system or language, the screens shown on your PC's
monitor will differ from the ones used in the following procedure.
The following procedure is applied both to USB WIRELESS and
USB TERMINAL.
1. The USB drivers are installed automatically.
• If the USB drivers are not installed automatically, install the
USB drivers by following the instructions on the PC’s
monitor.
2. Check if the drivers are correctly installed.
1. Open the Control Panel on your PC:
Select [Start] = [Control Panel].
2. Select [System] = [Hardware] = [Device Manager] =
[Sound, video and game controllers] = [Universal Serial
Bus controllers].
• The following window appears, and you can check whether
the drivers are installed.
If no sound comes from the speakers, check the following
items:
(For both USB WIRELESS and USB TERMINAL)
- check the USB device is recognized properly.
- check the playback software in your PC is compatible with the
USB device.
- open the Control Panel on your PC, select [Sounds and Audio
Devices] = [Audio] tab = [Sound playback] = [Default device],
and check [Default device] is set to [USB Audio device].
(For USB WIRELESS)
- select “USB WIRELESS” as the source.
- connect the USB wireless transmitter correctly with the USB
WIRELESS switch on the receiver “ON.”
- keep proper distance between the receiver and your PC.
- check the ID lamp on the transmitter and the signal indicators
“L” and “R” on the display light up.
(For USB TERMINAL)
- select “USB TERMINAL” as the source.
- connect the USB cable correctly.
NOTES
• DO NOT turn off the receiver or disconnect the transmitter or
the USB cable while installing the drivers and for several
seconds while your PC is recognizing the receiver.
• If your PC does not recognize the receiver, disconnect the
transmitter or the USB cable and connect it again. If it does not
work yet, restart Windows.
• The installed drivers can be recognized only when the
transmitter is connected to your PC or the USB cable is
connected between the receiver and your PC.
• The sound may not be played back correctly—interrupted or
degraded—due to your PC settings and PC specifications.
• Use a USB cable (version 1.1 or later). Recommended cord
length is 1.5 m.
* Microsoft®, Windows® 98 SE, Windows® Me, Windows® 2000,
and Windows® XP are registered trademarks of Microsoft
corporation.
Now PC is ready for playback through the USB connection.
After installation is completed, you can use your PC as the
playback source. The PC automatically recognizes the receiver
whenever the transmitter is connected to the PC or the USB cable
is connected between the PC and the receiver while the receiver
is turned on.
• When not using the PC as the playback source, disconnect the
transmitter or the USB cable.
To play back sounds on the PC, refer to the manuals supplied
with the sound reproduction application installed in the PC. Start
the application after the USB device is recognized.
When playing back with USB WIRELESS,
connect the transmitter and aim the transmitter at the antenna. If
any obstacles are in between, playback will be interrupted or the
wireless communication will be canceled.
If noise comes during playback with USB WIRELESS,
press CHANNEL to change the frequency band.
• By pressing CHANNEL for more than 3 seconds, you can
search for the frequency band which is not used around
automatically.
13
11-13D301J2.p65
13
05.2.23, 11:38
warranty.p65
05.2.22, 16:45
warranty.p65
05.2.22, 16:45

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Copy, Fill forms, Extract, Assemble, Print high-res
Modify Date                     : 2005:04:08 18:57:18+08:00
Create Date                     : 2005:02:23 15:05:21+09:00
Title                           : cover_RX-D301S[J]_f.p65
Author                          : ‹Éfi„
Creator                         : PageMaker 6.5
Producer                        : Acrobat Distiller 4.0 for Macintosh
Page Count                      : 5
Mod Date                        : 2005:04:08 18:57:18+08:00
Creation Date                   : 2005:02:23 15:05:21+09:00
Metadata Date                   : 2005:04:08 18:57:18+08:00
Has XFA                         : No
EXIF Metadata provided by EXIF.tools
FCC ID Filing: ASIV2T001

Navigation menu