JVC KW AVX824UI AVX826/824[A/UI] Install User Manual LVT1997 008A

KW-AVX826A KW-AVX826A LVT1997-008A English, INSTALLATION MANUAL

KW-AVX824UI KW-AVX824UI INSTALLATION MANUAL LVT1997-008A

User Manual: JVC KW-AVX824UI KW-AVX824UI English, INSTALLATION MANUAL

Open the PDF directly: View PDF PDF.
Page Count: 2

Connecting the parking brake lead
Connect the parking brake lead to the parking brake system built in the car.
To metallic body or
chassis of the car
Parking brake switch
(inside the car)
Parking brake lead
(light green)
Parking brake Crimp
connector
A
a
TROUBLESHOOTING
• The fuse blows.
* Are the red and black leads connected correctly?
• Power cannot be turned on.
* Is the yellow lead connected?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• Noise interfere with sounds.
* Is the rear ground terminal connected to the car’s chassis using shorter and
thicker cords?
• Unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• This unit does not work at all.
* Have you reset your unit?
1
Power cord
ELECTRICAL CONNECTIONS
To prevent short circuits, we recommend that
you disconnect the battery’s negative terminal
and make all electrical connections before
installing the unit.
• Be sure to ground this unit to the car’s
chassis again after installation.
KW-AVX826/KW-AVX824
Installation/Connection Manual
Parts list for installation and connection
The following parts are provided for this unit.
If anything is missing, contact your dealer immediately.
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. However, you should make adjustments corresponding to your specific
car. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a
company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Before installing the unit
• When mounting the unit, be sure to use the screws provided, as instructed. If other screws are used, parts could become
loose or damaged.
• When tightening screws or bolts, be careful not to pinch any connection cord.
• Make sure not to block the fan on the rear to maintain proper ventilation when installing the unit.
1 Remove the audio system originally installed in the car,
together with its mounting brackets.
Note: Be sure to keep all the screws and parts removed from
your car for future use.
2 Attach the mounting brackets (removed from the car) to this
unit (see below).
LVT1997-008A
[A/UI]
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical
systems. If your vehicle does not have this system, a voltage inverter is required,
which can be purchased at JVC car audio dealers.
WARNINGS
• DO NOT install any unit or wire any cable in a location where;
– it may obstruct the steering wheel and gearshift lever operations, as this may
result in a traffic accident.
– it may obstruct the operation of safety devices such as air bags, as this may
result in a fatal accident.
– it may obstruct visibility.
• DO NOT operate any unit while manipulating the steering wheel, as this may
result in a traffic accident.
• The driver must not watch the monitor while driving. It may lead to carelessness
and cause an accident.
• If you need to operate the unit while driving, be sure to look around carefully or
you may be involved in a traffic accident.
• If the parking brake is not engaged, “Parking Brake” flashes on the monitor, and
no playback picture will be shown.
– This warning appears only when the parking brake wire is connected to the
parking brake system built in the car.
Notes on electrical connections:
• Replace the fuse with one of the specified rating. If the fuse blows frequently,
consult your JVC car audio dealer.
• It is recommended to connect speakers with maximum power of more than 50 W
(both at the rear and at the front, with an impedance of 4  to 8 Ω).
If the maximum power is less than 50 W, change <Amplifier Gain> setting to
prevent the speakers from being damaged (see page 20 of the INSTRUCTIONS).
• To prevent short circuits, cover the terminals of the UNUSED leads with
insulating tape.
• The heat sink becomes very hot after use. Be careful not to touch it when
removing this unit.
• At the time of installation, be sure to fix all wires (wires both from this unit and
from the car itself) in a way that any wires cannot come into contact with heat
sinks on the rear and side of the unit.
Main unit
Round head screws
(M5 × 8 mm)
Flat head screws
(M5 × 8 mm)
Crimp connector
Remote
controller Batteries
If necessary, restore the
protruding tabs.
Supplied screws
Note : When installing the unit on the mounting bracket, make sure to use the supplied screws (M5 x 8 mm). If longer
screws are used, they could damage the unit.
Plate for use with a Nissan
car
When installing the unit in a Nissan car
Install the unit at an angle of less than 30˚,
taking it into account that the monitor
would eject when in use.
Required space for installation and
the monitor ejection
Unit: mm
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the power cord to the car
battery; otherwise, the unit will be seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers,
check the speaker wiring in your car.
Screws removed from the car in step 1
Supplied
screws
Select the
appropriate
type fitting
to your audio
system space.
Mounting bracket removed from the car
Heat sink
0209MNMMDWJEIN
EN
© 2009 Victor Company of Japan, Limited
Microphone holderMicrophone Microphone clip
Monitor panel and soft
case
AV I/O
cord
LINE OUT
cord
3 Do the required electrical connections.
• See “ELECTRICAL CONNECTIONS” on pages
1 and 2.
4 Install this unit using the screws removed in step 1.
5 Attach the monitor panel (see below).
The following example is for installation in a Toyota car. For more details, consult your JVC car audio dealer.
160 91.3
100
Dashboard
20
4
30˚
Plate for use with a Nissan car
Step 5
Monitor
panel
Instal1-2_KW-AVX826[AUI].indd 1Instal1-2_KW-AVX826[AUI].indd 1 09.2.4 9:47:16 PM09.2.4 9:47:16 PM
2
POSITION OUT
CAMERA IN
VIDEO OUT
2nd AUDIO OUT
LINE IN
VIDEO IN
REVERSE
GEAR
SIGNAL
L
R
L
R
*4
L
R
L
R
LRL
L
INPUT
INPUT
R
L
INPUT
R
L
R
L
R
R
*3
*3
*3
LINE OUT (FRONT)
LINE OUT (REAR)
SUBWOOFER
1
2
3
4
5
9
6
1
(ILLUMINATION CONTROL)
(PARKING BRAKE)
7
(TEL MUTING)
3
8
2
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious
damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in color.
*1
*1
15 A fuse
Fan
*1 Not included for this unit
*2 Before checking the operation of this unit prior to
installation, this lead must be connected, otherwise
power cannot be turned on.
Ignition switch
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
To metallic body or chassis of the car
To an accessory terminal in the fuse block
To the remote lead of other equipment (200 mA max.)
To automatic antenna if any
(250 mA max.)
Fuse block
To cellular phone system
To car light control switch
Crimp connector
To parking brake (see diagram
Å on page 1).
Ye l l o w *2
Red
Orange with white stripe
Black
Light green
Brown
Blue with white stripe
Blue
Left speaker
(rear)
Right speaker
(front)
Left speaker
(front)
Right speaker
(rear)
Gray with
black stripe
White
White with
black stripe
Green with
black stripe
Gray Green Purple with
black stripe Purple
Rear ground terminal
*3 Firmly attach the ground lead to the metallic body or to
the chassis of the car—to the place uncoated with paint
(if coated with paint, remove the paint before attaching
the lead). Failure to do so may cause damage to the unit.
BConnecting the LINE OUT cord
Rear speakers
JVC
Amplifier
You can connect amplifiers to upgrade surround system in the car compartment.
• You can supply the power to the amplifiers by connecting the remote leads (blue with
white stripe) of this unit and amplifiers. (To connect more than one amplifier using
the remote leads, Y-connectors need to be separately purchased.)
• Disconnect the speakers from the unit, and connect them to the amplifier. Leave the
speaker leads of the unit unused.
• You can switch off the built-in amplifier and send the audio signals only to the
external amplifier(s) to get clear sounds and to prevent internal heat built-up inside
the unit. See page 20 of the INSTRUCTIONS.
Front speakers
Subwoofer
OE remote
adapter (not
supplied)
Steering wheel remote
controller (equipped in
the car)
AConnecting to the steering wheel remote controller
If your car is equipped with
the steering wheel remote
controller, you can operate
this unit using the controller.
For connection, an exclusive
remote adapter (not supplied)
which matches your car is
required. For details, consult
the same car audio dealer as
where the unit is purchased.
Connecting the AV I/O cord
C
Connecting external components
When connecting the external components, refer also to the manuals supplied for the components and adapter.
CAUTION:
Before connecting the external components, make sure that the unit is turned off.
You can connect the following JVC components to the CD changer jack.
JVC component Model name
CD changer (CD-CH) CH-X1500, etc.
You can also connect the following components through the various JVC adapters.
• Connection cords may need to be purchased separately.
Component Adapter Model name
iPod Interface adapter for iPod KS-PD100*7
Portable audio player with line output jacks Line input adapter KS-U57*7
Portable audio player with 3.5 mm stereo mini jack AUX input adapter KS-U58*7
To disconnect the connector
Hold the connector top tightly (
1 ), then pull it out ( 2 ).
E
*7
To use these components, set the external input setting correctly (see page 18 of the INSTRUCTIONS).
USB devices
USB cable (approx. 1.2 m)
USB device
You cannot connect
a computer to
the USB ( )
terminal of the unit.
Connecting the iPod or the iPhone to the USB terminal
You can connect the iPod or the iPhone to the USB terminal using the following cables:
– To listen to the music: USB 2.0 cable (supplied for the iPod and the iPhone)
– To watch the video: USB Audio and Video cable for iPod—KS-U30 (not supplied)*8
iPod/iPhone
*8 When using the cable, make sure <iPod (Off)> is selected for <AV Input> (see page 18 of the
INSTRUCTIONS).
KS-U30
USB 2.0 cable
KW-AVX826/
KW-AVX824
Cordless headphones
(KS-HP2)
2nd monitor
(KV-MR9010, etc.)
• iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
• iPhone is a trademark of Apple Inc.
iPod/iPhone
AV amplifier
or decoder
Camcorder,
Navigation System,
etc.
Extension lead
(not supplied)
Video cord (not supplied)
Crimp connector (not
supplied)*5
Audio/video cord
(not supplied)
Digital optical
cable (not
supplied)
To reverse
lamp
Reverse
lamp lead
To car
battery
*6
*6
1 Connect the colored leads of the power cord in the order specified in the illustration below.
2 Connect the antenna cord.
3 Finally connect the wiring harness to the unit.
OE REMOTE
Steering wheel remote
JVC
Amplifier
JVC
Amplifier
DConnecting the microphone
12
Microphone
Secure the microphone cord
using cord cramps (not supplied)
if necessary.
or
KW-AVX826/
KW-AVX824 Adhesive
tape
KV-CM1
Rear view camera
(not supplied)
*4 Required only when connecting a rear view camera to CAMERA IN plug.
*5 Refer to å in diagram Å on page 1.
*6 POSITION OUT terminal: This terminal is used for controlling an external device by using the touch panel of
this unit. This unit outputs the positional information detected on the touch panel through the POSITION OUT
terminal. Refer to the instruction manual of the external device for details.
JVC does not guarantee proper operations for the external device connected to the POSITION OUT terminal.
Reverse lamp
Microphone
holder
Microphone clip
Instal1-2_KW-AVX826[AUI].indd 2Instal1-2_KW-AVX826[AUI].indd 2 09.2.4 9:47:22 PM09.2.4 9:47:22 PM

Navigation menu