JVC KW AVX824UI AVX826/824[A/UI] Install User Manual LVT1997 008A
KW-AVX826A KW-AVX826A LVT1997-008A English, INSTALLATION MANUAL
KW-AVX824UI KW-AVX824UI INSTALLATION MANUAL LVT1997-008A
User Manual: JVC KW-AVX824UI KW-AVX824UI English, INSTALLATION MANUAL
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
KW-AVX826/KW-AVX824 Installation/Connection Manual 0209MNMMDWJEIN EN © 2009 Victor Company of Japan, Limited LVT1997-008A [A/UI] This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers. WARNINGS • DO NOT install any unit or wire any cable in a location where; – it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident. – it may obstruct the operation of safety devices such as air bags, as this may result in a fatal accident. – it may obstruct visibility. • DO NOT operate any unit while manipulating the steering wheel, as this may result in a traffic accident. • The driver must not watch the monitor while driving. It may lead to carelessness and cause an accident. • If you need to operate the unit while driving, be sure to look around carefully or you may be involved in a traffic accident. • If the parking brake is not engaged, “Parking Brake” flashes on the monitor, and no playback picture will be shown. – This warning appears only when the parking brake wire is connected to the parking brake system built in the car. Notes on electrical connections: • Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer. • It is recommended to connect speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W, changesetting to prevent the speakers from being damaged (see page 20 of the INSTRUCTIONS). • To prevent short circuits, cover the terminals of the UNUSED leads with insulating tape. • The heat sink becomes very hot after use. Be careful not to touch it when removing this unit. • At the time of installation, be sure to fix all wires (wires both from this unit and from the car itself) in a way that any wires cannot come into contact with heat sinks on the rear and side of the unit. INSTALLATION (IN-DASH MOUNTING) The following illustration shows a typical installation. However, you should make adjustments corresponding to your specific car. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits. • If you are not sure how to install this unit correctly, have it installed by a qualified technician. Before installing the unit • When mounting the unit, be sure to use the screws provided, as instructed. If other screws are used, parts could become loose or damaged. • When tightening screws or bolts, be careful not to pinch any connection cord. • Make sure not to block the fan on the rear to maintain proper ventilation when installing the unit. 1 Remove the audio system originally installed in the car, together with its mounting brackets. Note: Be sure to keep all the screws and parts removed from your car for future use. 2 Attach the mounting brackets (removed from the car) to this unit (see below). Do the required electrical connections. • See “ELECTRICAL CONNECTIONS” on pages 1 and 2. 4 5 Install this unit using the screws removed in step 1. Attach the monitor panel (see below). The following example is for installation in a Toyota car. For more details, consult your JVC car audio dealer. Supplied screws Select the appropriate type fitting to your audio system space. Mounting bracket removed from the car If necessary, restore the protruding tabs. Supplied screws Heat sink 3 Screws removed from the car in step 1 Step 5 When installing the unit in a Nissan car Monitor panel TROUBLESHOOTING Plate for use with a Nissan car • The fuse blows. * Are the red and black leads connected correctly? • Power cannot be turned on. * Is the yellow lead connected? Note : • No sound from the speakers. * Is the speaker output lead short-circuited? • Sound is distorted. * Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common? When installing the unit on the mounting bracket, make sure to use the supplied screws (M5 x 8 mm). If longer screws are used, they could damage the unit. Required space for installation and the monitor ejection Dashboard 20 100 4 • Noise interfere with sounds. * Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords? • Unit becomes hot. * Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common? 30˚ • This unit does not work at all. * Have you reset your unit? 160 Parts list for installation and connection Monitor panel and soft case AV I/O cord Power cord Unit: mm 91.3 ELECTRICAL CONNECTIONS The following parts are provided for this unit. If anything is missing, contact your dealer immediately. Main unit Install the unit at an angle of less than 30˚, taking it into account that the monitor would eject when in use. Plate for use with a Nissan car To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit. • Be sure to ground this unit to the car’s chassis again after installation. PRECAUTIONS on power supply and speaker connections: • DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged. • BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car. LINE OUT cord A Connecting the parking brake lead Connect the parking brake lead to the parking brake system built in the car. Remote controller Batteries a Flat head screws (M5 × 8 mm) Round head screws (M5 × 8 mm) Parking brake lead (light green) Crimp connector Parking brake Microphone Microphone clip Crimp connector Microphone holder Parking brake switch (inside the car) To metallic body or chassis of the car 1 Instal1-2_KW-AVX826[AUI].indd 1 09.2.4 9:47:16 PM Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit. The leads of the power cord and those of the connector from the car body may be different in color. 1 2 3 Rear ground terminal Connect the colored leads of the power cord in the order specified in the illustration below. Connect the antenna cord. Finally connect the wiring harness to the unit. 3 *1 Fan Black 1 Yellow *2 Ignition switch *1 To metallic body or chassis of the car 2 To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch) (constant 12 V) Red 3 To an accessory terminal in the fuse block To automatic antenna if any Fuse block 4 (250 mA max.) 5 To the remote lead of other equipment (200 mA max.) 6 To car light control switch Blue Blue with white stripe 15 A fuse 2 Orange with white stripe 1 *1 Not included for this unit *2 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot be turned on. White with black stripe (ILLUMINATION CONTROL) Brown 7 To cellular phone system (TEL MUTING) Light green 9 Gray with black stripe White Green with black stripe Gray Left speaker (front) C A Connecting to the steering wheel remote controller KV-CM1 2nd AUDIO OUT AV amplifier or decoder L R LINE IN L R L R VIDEO IN REVERSE GEAR SIGNAL POSITION OUT Extension lead (not supplied) *4 *6 Crimp connector (not supplied)*5 To car battery Rear speakers INPUT JVC Amplifier L L R R *3 L R R D Connecting the microphone 1 2 Microphone L or JVC Amplifier INPUT KW-AVX826/ KW-AVX824 *3 Firmly attach the ground lead to the metallic body or to the chassis of the car—to the place uncoated with paint (if coated with paint, remove the paint before attaching the lead). Failure to do so may cause damage to the unit. *3 Microphone clip Secure the microphone cord using cord cramps (not supplied) if necessary. Microphone Adhesive holder tape USB devices Connecting external components When connecting the external components, refer also to the manuals supplied for the components and adapter. USB cable (approx. 1.2 m) USB device CAUTION: Before connecting the external components, make sure that the unit is turned off. You can connect the following JVC components to the CD changer jack. JVC component Model name CD changer (CD-CH) CH-X1500, etc. You cannot connect a computer to the USB ( ) terminal of the unit. KW-AVX826/ KW-AVX824 You can also connect the following components through the various JVC adapters. • Connection cords may need to be purchased separately. Connecting the iPod or the iPhone to the USB terminal Component Adapter Model name iPod Interface adapter for iPod KS-PD100*7 Portable audio player with line output jacks Line input adapter KS-U57*7 Portable audio player with 3.5 mm stereo mini jack AUX input adapter KS-U58*7 *7 Camcorder, Navigation System, etc. Reverse lamp *4 Required only when connecting a rear view camera to CAMERA IN plug. *5 Refer to å in diagram Å on page 1. *6 POSITION OUT terminal: This terminal is used for controlling an external device by using the touch panel of this unit. This unit outputs the positional information detected on the touch panel through the POSITION OUT terminal. Refer to the instruction manual of the external device for details. JVC does not guarantee proper operations for the external device connected to the POSITION OUT terminal. Subwoofer E Cordless headphones (KS-HP2) *6 SUBWOOFER *3 LINE OUT (REAR) R LINE OUT (FRONT) L R To reverse lamp Reverse lamp lead Front speakers JVC Amplifier 2nd monitor (KV-MR9010, etc.) L R Audio/video cord (not supplied) VIDEO OUT Digital optical cable (not supplied) Rear view camera (not supplied) Video cord (not supplied) Connecting the LINE OUT cord INPUT L Right speaker (rear) Connecting the AV I/O cord OE REMOTE Steering wheel remote Purple Left speaker (rear) CAMERA IN You can connect amplifiers to upgrade surround system in the car compartment. • You can supply the power to the amplifiers by connecting the remote leads (blue with white stripe) of this unit and amplifiers. (To connect more than one amplifier using the remote leads, Y-connectors need to be separately purchased.) • Disconnect the speakers from the unit, and connect them to the amplifier. Leave the speaker leads of the unit unused. • You can switch off the built-in amplifier and send the audio signals only to the external amplifier(s) to get clear sounds and to prevent internal heat built-up inside the unit. See page 20 of the INSTRUCTIONS. Purple with black stripe Green Right speaker (front) If your car is equipped with Steering wheel remote the steering wheel remote controller (equipped in controller, you can operate the car) OE remote this unit using the controller. adapter (not For connection, an exclusive supplied) remote adapter (not supplied) which matches your car is required. For details, consult the same car audio dealer as where the unit is purchased. B 8 (PARKING BRAKE) To parking brake (see diagram Å on page 1). Crimp connector You can connect the iPod or the iPhone to the USB terminal using the following cables: – To listen to the music: USB 2.0 cable (supplied for the iPod and the iPhone) – To watch the video: USB Audio and Video cable for iPod—KS-U30 (not supplied)*8 KS-U30 iPod/iPhone To use these components, set the external input setting correctly (see page 18 of the INSTRUCTIONS). USB 2.0 cable iPod/iPhone To disconnect the connector *8 When using the cable, make sure is selected for (see page 18 of the INSTRUCTIONS). Hold the connector top tightly ( 1 ), then pull it out ( 2 ). • iPod is a trademark of Apple Inc., registered in the U.S. and other countries. • iPhone is a trademark of Apple Inc. 2 Instal1-2_KW-AVX826[AUI].indd 2 09.2.4 9:47:22 PM
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Fill forms, Extract, Assemble, Print high-res Create Date : 2009:02:04 21:48:41+09:00 Modify Date : 2009:02:19 18:45:02+09:00 Subject : LVT1997-008A Producer : Acrobat Distiller 7.0.5 for Macintosh Mod Date : 2009:02:19 18:45:02+09:00 Creation Date : 2009:02:04 21:48:41+09:00 Author : JVC Creator Tool : Adobe InDesign CS (3.0.1) Metadata Date : 2009:02:19 18:45:02+09:00 Document ID : uuid:309b69fc-f2ba-11dd-b32d-0017f2c2a5e6 Instance ID : uuid:309bc56f-f2ba-11dd-b32d-0017f2c2a5e6 Format : application/pdf Creator : JVC Title : KW-AVX826/824[A/UI] install Description : LVT1997-008A Page Count : 2 Page Mode : UseThumbs Page Layout : SinglePageEXIF Metadata provided by EXIF.tools