JVC KW V340BTM KW_V340BT_M User Manual V340BTM, V440BTM B5A 2150 00 KW-V440BT KW-V440BT, KW-V440BTM B5A_2150_00 English, (Instruction manual) Asia KW-V340BT KW-V340BT, KW-V340BTM, KW-V440BT, KW-V440BTM B5A_2150_00 English, (Instruction manual) Asia KW-V340BT, KW-V340BTM KW-V340BT, KW-V340BTM (Instruction manual) Asia B5A_2150_00
User Manual: JVC KW-V340BTM KW-V340BTM, KW-V440BTM English, (Instruction manual) Asia
Open the PDF directly: View PDF .Page Count: 60
ENGLISH
MONITOR WITH DVD RECEIVER
INSTRUCTION MANUAL
KW-V340BT
KW-V340BT
KW-V340BTM
KW-V440BT
KW-V440BTM
(Region 3 – DVD Region Code 3 Area)
(Region 4 – DVD Region Code 4 Area)
(Region 2 – DVD Region Code 2 Area)
(Region 3 – DVD Region Code 3 Area)
(Region 2 – DVD Region Code 2 Area)
This instruction manual is used to describe models listed above. Model availability and features (functions)
may differ depending on the country and sales area.
00_KW-V2018ST_M_ENG.indb 1
B5A-2150-00 (M/M2/X/A9)
17/6/2017 7:35:42 AM
Important Notice
To ensure proper use, please read through this
manual before using this product. It is especially
important that you read and observe WARNINGS
and CAUTIONS in this manual.
Please keep the manual in a safe and accessible
place for future reference.
WARNINGS
To prevent accidents and damages
• DO NOT install any unit or wire any cable in a
location where;
– it may obstruct the steering wheel and gearshift
lever operations.
– it may obstruct the operation of safety devices such
as air bags.
– it may obstruct visibility.
• DO NOT raise the volume level too much, as this will
make driving dangerous by blocking outside sounds,
and may cause hearing loss.
• DO NOT operate the unit while driving. If you need
to operate the unit while driving, be sure to look
around carefully.
• Stop the car before performing any complicated
operations.
• The driver must not watch the monitor while driving.
i
CAUTIONS
To care for the unit
• If you have parked the car for a long time in hot or
cold weather, wait until the temperature in the car
becomes normal before operating the unit.
To care for the monitor
• The monitor built into this unit has been produced
with high precision, but it may have some ineffective
dots. This is inevitable and is not considered
defective.
• Do not expose the monitor to direct sunlight.
• Do not operate the touch panel using a ball-point
pen or similar tool with a sharp tip.
Touch the keys on the touch panel with your finger
directly (if you are wearing a glove, take it off).
• When the temperature is very cold or very hot...
– Chemical changes occur inside, causing
malfunction.
– Pictures may not appear clearly or may move
slowly. Pictures may not be synchronized with
the sound or picture quality may decline in such
environments.
On the volume setting
• Digital devices produce very little noise compared
with other sources. Lower the volume before playing
these digital sources to avoid damaging the speakers
by sudden increase of the output level.
The marking of products using lasers
The label is attached to the chassis/case and says
that the component uses laser beams that have been
classified as Class 1. It means that the unit is utilizing
laser beams that are of a weaker class. There is no
danger of hazardous radiation outside the unit.
ENGLISH
00_KW-V2018ST_M_ENG.indb i
17/6/2017 7:35:43 AM
Important Notice
For KW-V340BTM Region 2/KW-V440BTM Region 2:
For Turkey
Bu ürün 28300 sayılı Resmi Gazete’de yayımlanan Atik
Elektrikli ve Elektronik Eşyalarin Kontrolü Yönetmeliğe
uygun olarak üretilmiştir.
Eski Elektrik ve Elektronik Ekipmanların İmha
Edilmesi Hakkında Bilgi (ayrı atık toplama
sistemlerini kullanan ülkeleri için uygulanabilir)
Sembollü (üzerinde çarpı işareti olan çöp
kutusu) ürünler ev atıkları olarak atılamaz.
Eski elektrik ve elektronik ekipmanlar,
bu ürünleri ve ürün atıklarını
geri dönüştürebilecek bir tesiste
değerlendirilmelidir. Yaşadığınız bölgeye
en yakın geri dönüşüm tesisinin yerini
öğrenmek için yerel makamlara müracaat
edin. Uygun geri dönüşüm ve atık
imha yöntemi sağlığımız ve çevremiz
üzerindeki zararlı etkileri önlerken
kaynakların korunmasına da yardımcı
olacaktır.
For KW-V340BTM Region 2/KW-V440BTM Region 2:
Declaration of Conformity with regard to the RE
Directive 2014/53/EU
Declaration of Conformity with regard to the RoHS
Directive 2011/65/EU
Manufacturer:
JVC KENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi,
Kanagawa, 221-0022, Japan
EU Representative:
JVCKENWOOD Deutschland GmbH
Konrad-Adenauer-Allee 1-11, 61118 Bad Vilbel,
GERMANY
English
Hereby, JVCKENWOOD declares that the radio
equipment “KW-V340BTM/KW-V440BTM” is in
compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is
available at the following internet address:
http://www.jvc.net/cs/car/eudoc/
RE 2014/53/EU Direktifi uyarınca Uygunluk Beyanı
RoHS Yönergesi 2011/65/EU’ya göre Uygunluk
Bildirimi
Üretici:
JVC KENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi,
Kanagawa, 221-0022, Japan
AB Temsilcisi:
JVCKENWOOD Deutschland GmbH
Konrad-Adenauer-Allee 1-11, 61118 Bad Vilbel,
GERMANY
Turkish
Burada, JVCKENWOOD “KW-V340BTM/KW-V440BTM”
radyo ekipmanının 2014/53/AB Direktifine uygun
olduğunu bildirir.
AB uyumluluk deklarasyonunun tam metni aşağıdaki
internet adresinde mevcuttur.
http://www.jvc.net/cs/car/eudoc/
ENGLISH
00_KW-V2018ST_M_ENG.indb ii
ii
17/6/2017 7:35:43 AM
About this manual
The displays and panels shown in this manual are
examples used to provide clear explanations of the
operations. For this reason, they may be different
from the actual displays or panels.
Illustrations of KW-V440BT are mainly used for
explanation.
The region code of a particular model will only
be stated if only one of the regions supports the
particular feature with the same model name.
This manual mainly explains operations using the
buttons on the monitor panel and keys on the
touch panel. For operations using the remote
controller, see page 41.
< > indicates the various screens/menus/
operations/settings that appear on the touch
panel.
Contents
Component Names and Operations .............. 3
Basic Operations ................................................ 3
How to reset your unit ................................................... 3
Turning on the power .................................................... 3
Turning off the power .................................................... 3
Turning off the AV source ............................................ 4
Turning off the screen.................................................... 4
Adjusting the volume .................................................... 4
Attenuating the sound ............................................... 4
Getting Started .................................................. 4
Initial settings....................................................................... 4
Clock settings ...................................................................... 5
Various Screens and Operations .................... 6
Home screen........................................................................ 6
Source control screen .................................................... 7
List/setting screen ............................................................ 9
Disc ..................................................................... 10
[ ] indicates the keys on the touch panel.
Video .................................................................. 11
Indication language: English indications are used
for the purpose of explanation. You can select the
indication language from the menu.
(Page 38)
USB ..................................................................... 13
Android.............................................................. 15
iPod/iPhone ...................................................... 16
Tuner .................................................................. 17
Pandora® ........................................................... 20
Spotify ............................................................... 22
Other External Components ......................... 24
AV-IN ...................................................................................... 24
Rear view camera ........................................................... 24
TV tuner box ...................................................................... 25
External navigation unit ............................................. 25
2
Bluetooth® ........................................................ 26
Information ........................................................................ 26
Preparation......................................................................... 26
Connection ........................................................................ 26
Bluetooth mobile phone........................................... 28
Bluetooth audio player ............................................... 30
JVC Streaming DJ ....................................................... 30
Bluetooth settings ......................................................... 31
Settings ............................................................. 31
Audio settings .................................................................. 31
Display settings ............................................................... 34
Input settings.................................................................... 37
System settings ............................................................... 38
Remote Controller ........................................... 41
Preparation......................................................................... 41
Basic operations .............................................................. 42
Searching for an item directly ................................ 42
JVC Remote APP.......................................................... 42
Installation and Connection .......................... 43
Before installation .......................................................... 43
Installing the unit ........................................................... 44
Installing the trim plate .............................................. 44
Wiring connection......................................................... 45
Connecting external components ...................... 46
References ........................................................ 46
Maintenance ..................................................................... 46
More information ........................................................... 46
Troubleshooting .............................................. 50
Specifications ................................................... 53
Trademarks and licenses ........................................... 56
ENGLISH
00_KW-V2018ST_M_ENG.indb 2
17/6/2017 7:35:43 AM
Component Names and Operations
KW-V340BT/KW-V340BTM
KW-V440BT/KW-V440BTM
Basic Operations
How to reset your unit
If the unit fails to operate properly, press the reset
button.
KW-V340BT/KW-V340BTM
KW-V440BT/KW-V440BTM
1
2
3
4
5
6
7
8
button
• (Press) Turns on the power.
• (Hold) Turns off the power.
• (Press) Pops up the short-cut menu while the
power is on.
Reset button
Loading slot
HOME/ button
• HOME (Press): Displays the Home screen.
• (Hold): Activates the voice dialing.
button
• (Press) Displays the current source control screen.
For KW-V340BT Region 3, KW-V340BTM
Region 2, pressing
switches the screen
between the current source control screen and
navigation screen. For details, see page 38.
• (Hold) Turns off/on the screen.
Volume +/– buttons
Monitor panel
Screen (touch panel)
1 Volume +/– buttons
2 Loading slot
3 FNC button
• (Press) Turns on the power.
• (Press) Pops up the short-cut menu while the
power is on.
• (Hold): Activates the voice dialing.
4 Reset button
5 Monitor panel
6 Screen (touch panel)
To display the Home screen
Turning on the power
KW-V340BT/
KW-V340BTM
KW-V440BT/
KW-V440BTM
Turning off the power
KW-V340BT/KW-V340BTM
(Hold)
ENGLISH
00_KW-V2018ST_M_ENG.indb 3
3
17/6/2017 7:35:43 AM
Getting Started
Basic Operations
KW-V440BT/KW-V440BTM
On the Home screen, touch as follows:
• For KW-V440BT/KW-V440BTM: See “Using the
pop-up short-cut menu” on page 8.
Initial settings
When you power on the unit for the first time or reset
the unit, the screen appears.
Adjusting the volume
KW-V340BT/
KW-V340BTM
Turning off the AV source
1
Perform the initial settings.
KW-V440BT/
KW-V440BTM
Display the source/option selection
screen.
On the Home screen, touch as follows:
2
Turn off the AV source.
On the source/option selection screen, touch as
follows:
You can adjust the volume (00 to 35) by pressing + to
increase and pressing – to decrease.
• Holding + increases the volume continuously to
level 15.
E.g. Initial settings screen for KW-V440BT
Once completed, Home screen appears.
For KW-V440BT Region 3, Indonesian models, a
caution message will appear.
Attenuating the sound
On the source control screen, touch as follows:
Turning off the screen
KW-V340BT/KW-V340BTM
[
To cancel attenuation: Touch [
becomes white.)
(Hold)
• The button illumination also lights off when you turn
off the screen.
To turn on the screen: Press and hold
monitor panel or touch the screen.
4
] becomes blue.
] again. ([
]
Touch [OK] to confirm the caution message.
• The caution message appears each time you turn on
the unit.
on the
ENGLISH
00_KW-V2018ST_M_ENG.indb 4
17/6/2017 7:35:44 AM
Getting Started
• ON (Initial)*1: Activates the display demonstration.
• OFF: Deactivates the display demonstration.
Select the text language used for on-screen
information.
• English (Initial)*2/Español/Français/Deutsch/
Italiano/Nederlands/Ελληνικά/Português/Türkçe/
/
/
Čeština/Polski/Magyar/Руccĸий/
/
/
/
/Bahasa
Malaysia/Bahasa Indonesia/
– For external monitors, only English/Spanish/
French/German/Italian/Dutch/Russian/Portuguese
are available. If another language has been
selected, the text language for external monitors
will be set to English.
• GUI Language (Local (the language selected
above)/English (Initial)*2): Selects the language used
for displaying operation keys and menu items.
“Please Power Off” appears when the setting is
changed. Turn off the power, then turn on to enable
the change.
(Page 37)
Make the settings to display the picture from the
connected rear view camera.
*1 For KW-V440BT Region 3, Indonesian models, is
selected initially.
*2 For KW-V440BT Region 3, Indonesian models, is selected initially.
3
Set the clock time.
Clock settings
1
Display the Home screen.
KW-V340BT/
KW-V340BTM
2
KW-V440BT/
KW-V440BTM
Display the screen.
On the Home screen, touch as follows:
E.g. Clock settings screen for KW-V440BT
• Radio Data System: Synchronizes the clock time
with FM Radio Data System.
• Off: Sets the clock manually. Touch [J]/[K] to
adjust the hour, then minute.
– Touching [Reset] will set the minute to “00”.
Then, on the screen, touch as follows:
[System] : [Enter]
• You can also display the screen by
touching the clock area on the Home screen.
(Page 35)
Change the display design.
Select the viewing angle in relation to the monitor
panel to make the panel easier to see.
• Under 0° (Initial)/5°/10°/15°/20°
ENGLISH
00_KW-V2018ST_M_ENG.indb 5
5
17/6/2017 7:35:44 AM
Various Screens and Operations
You can display or change to other screens at any time
to show information, change the AV source, change
the settings, etc.
KW-V440BT/KW-V440BTM
• You can change the icon design. For details, see
page 36.
Home screen
When you turn on the power for the first time, the
Home screen appears.
• You can customize the Home screen. (Pages 7
and 35)
• To display the Home screen from other screens:
For KW-V340BT/KW-V340BTM: Press HOME on the
monitor panel.
For KW-V440BT/KW-V440BTM: Press FNC on the
monitor panel, then touch [Home] on the pop-up
short-cut menu.
KW-V340BT/KW-V340BTM
• You can change Home screen design (icons and
layout). For details, see page 35.
Touching the operation keys performs the following
actions:
1 Displays the screen.
2 Ejects the disc.
3 Displays the screen.
4 Displays the screen.
5 Displays all playback sources and options.
6 Selects or changes the playback source.
7 Displays the phone control screen.
Available playback sources and options
Touch 5 to display the source/option selection screen.
Touching the operation keys performs the following
actions:
[Tuner]
Switches to the radio broadcast.
[Disc]
Plays a disc.
[USB]
Plays files on a USB device.
[iPod]
Plays an iPod/iPhone.
[Android™]
Plays an Android device.
[BT Audio]
Plays a Bluetooth audio player.
[AV-IN]
Switches to an external component
connected to the AV-IN input
terminal.
[Spotify]
Switches to the Spotify application.
[Pandora]*1
Switches to the Pandora Broadcast.
[Navi]*2
Displays the navigation screen.
[Phone]
Displays the phone control screen.
[AV Off]
Turns off the AV source.
[Home]*3
Displays the Home screen.
[Setup]*3
Displays the screen.
[Power Off]*3
Turns off the power.
[Camera]
Switches to the camera connected
to the rear view camera input.
[Now Playing]*3 Displays the source currently
played back.
E.g. Source/option selection screen for KW-V440BT
6
*1 Only for KW-V340BT Region 4.
*2 Only for KW-V340BT Region 3, KW-V340BTM Region 2,
KW-V440BT Region 3 (except for Indonesian models),
KW-V440BTM Region 2. Selectable only when a navigation unit
is connected.
*3 Only for KW-V440BT/KW-V440BTM.
ENGLISH
03_KW_V340BT_M_Body01.indd 6
18/7/2017 9:49:24 AM
Various Screens and Operations
To return to the Home screen
Touch [
] or [Home] on the source/option
selection screen.
Customizing the Home screen
1
Select an item to replace.
On the Home screen, touch and hold the icon you
want to replace.
The item selection screen is displayed.
2
Select an item (1) you want to display in
the selected position, then touch [
]
(2).
Source control screen
You can perform the playback operation from the
source control screen during playback.
• The operation keys and information displayed vary
depending on the selected source/disc type/file type
being played.
• If the operation keys are not displayed on the screen,
touch the screen to show them.
E.g. Common audio playback source screen:
KW-V340BT/KW-V340BTM
Repeat the procedure to customize your Home
screen.
E.g. Home item selection screen for KW-V440BT
KW-V440BT/KW-V440BTM
1 Playing time/playback status
2 Playback source or media type
3 Current playback item information
(folder no./file no./track no./total track no./playback
file type)
4 [M]: Ejects the disc.
[
]: Attenuates/restores the sound.
5 Clock display
6 Only for KW-V340BT/KW-V340BTM: Playback
source items shown on the Home screen.
• Touching the playback source item changes the
playback source.
7 Displays/hides other available operation keys*
8 Operation keys*
9 IN indicator (lights up while a disc is inserted)
p Track/file/song/video information
• Touching [H] scrolls the text if not all of the text
is shown.
q Playback mode indicator (Repeat/Random)
w File type indicator
e Picture/artwork (shown if the file contains the
information)
* See “Common operation keys on source control screen” on
page 8.
• Only selectable sources are shown.
• You cannot locate [Camera] on the Home
screen.
ENGLISH
03_KW_V340BT_M_Body01.indd 7
7
18/7/2017 9:55:35 AM
Various Screens and Operations
Common operation keys on source control screen
• The following explanations state the operation keys
for KW-V440BT, unless stated otherwise.
• The appearance of the operation keys may differ,
however the similar operation keys have the same
operations.
• Available operation keys differ depends on the
selected source or connected device.
Touching the operation keys performs the following
actions:
8
Using gesture control
[FNC J]
[
]
For KW-V440BT/KW-V440BTM:
Displays the Home screen.
[
]
Displays the folder list/track list/audio
menu/video menu.
• (Touch) Selects an item (chapter/
folder/track/audio file/video file).
• (Hold) Reverses/forwards search.
• (Hold) Plays in slow-motion while
paused for video playback.
Starts/pauses playback.
[S]/[T]
7
Displays other available operation keys
besides those shown on 8.
• To hide the window, touch [ ].
[ ]
[
][
[
]
]
For KW-V340BT/KW-V340BTM:
Displays the pop-up short-cut menu.
• To close the menu, touch [K].
[IW]
[
]
Selects random playback mode.*
Selects a folder.
Selects repeat playback mode.*
[o]
Stops playback.
[MODE]
Displays the setting screen of the current
playback source.
* About playback mode:
– Available playback mode differs depending on the source, disc
type, connected device, etc.
– You cannot activate repeat playback mode and random
playback mode at the same time.
– To cancel the playback mode, touch repeatedly until the
indicator disappears.
You can also control playback by moving your finger
on the touch panel as follows (for some sources, the
gesture control is not available).
• Sliding the finger up/down:
Selects a folder.
• Sliding the finger left/right:
Selects an item (chapter/track/audio file/video file).
• Moving your finger clockwise/counterclockwise:
Increases/decreases the volume.
Using the pop-up short-cut menu
While displaying the source control screen, you can
jump to another screen by touching the operation
keys on the pop-up short-cut menu.
1
Display the pop-up short-cut menu.
KW-V340BT/
KW-V340BTM
8
KW-V440BT/
KW-V440BTM
ENGLISH
00_KW-V2018ST_M_ENG.indb 8
17/6/2017 7:35:45 AM
Various Screens and Operations
2
Select an item to jump to by touching as
follows.
For KW-V340BT/KW-V340BTM:
Displays the phone control screen.
[ ]
Activates the voice dialing.
[ ]
[
]
Displays the screen.
[
]
Displays the picture adjustment screen.
Using touch screen operation during
playback
Displays the screen.
]
[
To close the pop-up menu
• KW-V340BT/KW-V340BTM: Touch [K] or touch the
screen anywhere other than the pop-up short-cut
menu.
• KW-V440BT/KW-V440BTM: Press FNC on the
monitor panel.
List/setting screen
Below are the common operation keys which appear
on the list/setting screen..
• The appearance of the operation keys may differ,
however the similar operation keys have the same
operations.
• Available operation keys differ depends on the
setting screens. Not all these operation keys are
shown on every screen.
For KW-V440BT/KW-V440BTM:
[
(Touch) Switches the screen.
(Hold) Turns off the screen.
]
Displays the phone control screen.
[ ]
Activates the voice dialing.
[ ]
[
Displays the picture from the connected
rear view camera.
]
[
]
Displays the picture adjustment screen.
[
]
Displays the screen.
[
]
Displays the Home screen.
[
]
Displays all playback sources and items.
• The playback source buttons/items displayed on
the Home screen are displayed on the pop-up
short-cut menu. Touching these operation keys
changes the playback source.
Touching the areas performs the following actions:
1 Displays the video control menu while playing a
video.
2 While playing a video: Displays the source control
screen.
While playing an audio file: Displays the playback
operation keys.
3 Goes to the previous chapter/track.*
4 Goes to the next chapter/track.*
* Not available for video from an external component (AV-IN).
Touching the operation keys performs the following
actions:
1 Enters alphabet search* to list the items in
alphabetical order. When a keypad appears, touch
the first letter you want to search for.
2 Returns to the root folder.
3 Returns to the upper layer.
4 Closes the current screen.
5 Exits from the current screen or returns to the
previous screen.
6 Changes the page to display more items.
* Alphabet search is not available when the playlist is selected.
ENGLISH
00_KW-V2018ST_M_ENG.indb 9
9
17/6/2017 7:35:45 AM
Disc
• If a disc does not have a disc menu, all tracks on it will
be played repeatedly until you change the source or
eject the disc.
• For playable disc types, file types and other
information, see pages 46 and 47.
• If “ ” appears on the screen, the unit cannot accept
the operation you have tried to do.
– In some cases, without showing “ ”, operations
will not be accepted.
• When playing back a multi-channel encoded disc,
the multi-channel signals are downmixed.
Selecting a folder/track on the list
Ejecting a disc
On the Home screen or source control screen, touch
as follows:
• When removing a disc, pull it out horizontally.
• You can eject a disc while playing another AV source.
• If the ejected disc is not removed within 15 seconds,
the disc is automatically inserted again into the
loading slot to protect it from dust.
1
Display the folder/track list.
On the source control screen, touch as follows:
2
Select the folder (1), then the item (2) in
the selected folder.
Inserting a disc
Label side up
Playback operations
Audio playback information and key
operation
E.g. Inserting a disc for KW-V440BT
The source changes to “DISC” and playback starts.
• The IN indicator lights up while a disc is inserted.
• For playback information, see “Source control screen”
on page 7.
• For key operations on the touch panel, see “Common
operation keys on source control screen” on
page 8.
Select an item in each layer until you reach and
select the desired file.
Settings for disc playback
• Available items shown on the screen
differ depending on the type of disc/file being
played back.
1
Display the screen.
On the source control screen, touch as follows:
10
ENGLISH
00_KW-V2018ST_M_ENG.indb 10
17/6/2017 7:35:45 AM
Video
Disc
2
Make the settings.
*1
Select the initial disc menu language. (Initial:
English)
*1
Select the initial subtitle language or turn subtitles
off (Off). (Initial: English)
*1
Select the initial audio language. (Initial: English)
You can change the dynamic range while playing
Dolby Audio encoded discs.
• Wide: Reproduces powerful sound at a low
volume level with its full dynamic range.
• Normal: Reduces the dynamic range a little.
• Dialog (Initial): Reproduces movie dialog more
clearly.
When playing back a multi-channel disc, this
setting affects the signals reproduced through the
front and/or rear speakers.
• Dolby Surround: Reproduces multi-channel
surround sound by connecting an amplifier
compatible with Dolby Surround.
• Stereo (Initial): Reproduces stereo playback
sound.
Playback operations
Video playback information on the source
control screen
Select the monitor type to watch a wide screen
picture on the external monitor.
16:9 (Initial)
4:3 LB
4:3 PS
E.g. Video playback source control screen for
KW-V440BT
*2
Select the playback file type when a disc contains
different types of files.
• Audio: Plays back audio files.
• Still image: Plays back still picture files.
• Video: Plays back video files.
• Audio&Video (Initial): Plays back audio files and
video files.
1 Media type
2 Playback status
3 Current playback item information
(title no./chapter no./folder no./file no./track no.)
4 Playing time
5 IN indicator (lights up while a disc is inserted)
6 Playback mode indicator (Repeat/Random)
7 File type indicator
*1 For list of language codes, see page 48.
*2 For playable file types, see page 46.
If the disc contains no files of the selected type, the existing
files are played in the following priority: audio, video, then still
picture. You can change these settings only while playback is
stopped.
ENGLISH
00_KW-V2018ST_M_ENG.indb 11
11
17/6/2017 7:35:46 AM
Video
Video menu control operations
You can display the video menu control during video
playback.
• Available operation keys differ depend on the
selected disc type and file type.
Touching the operation keys performs the following
actions:
Displays the picture adjustment screen.
1 Touch [DIM ON] or [DIM OFF] to
turn on or off the dimmer.
2 Touch [+]/[–] to adjust the other
items.
• : Adjusts the brightness
(−15 to +15).
• : Adjusts the contrast
(−10 to +10).
• : Adjusts the blackness
(−10 to +10).
• : Adjusts the color
(−10 to +10).
• : Adjusts the tint (−10 to +10).
• : Adjusts the sharpness
(−2 to +2).
]
1
[
]*1
Displays the picture size selection
screen.
1 Touch [ Zoom] to change the
magnification level of the picture
(Zoom1, Zoom2, Zoom3, Full:
Initial).
2 Touch [J] [K] [H] [I] to move the
zooming frame.
[
]
Displays the aspect ratio selection
screen.
Touch [ Aspect] to select the aspect
ratio.
*2: For 16:9 original pictures
4:3 signal
16:9 signal
Video playback except VCD
E.g. Video menu control screen for KW-V440BT
[
]
[
]
[
: For viewing 4:3 pictures
naturally on the wide screen
4:3 signal
16:9 signal
*2: For 4:3 original pictures
4:3 signal
16:9 signal
[
]
Selects the audio type.
Selects the subtitle type.
Selects the view angle.
*1 When [
] is set to or , the picture is
zoomed with the aspect ratio of the setting.
This feature may not be used for some video sources.
*2 While DivX is played back with set to [16:9]
(Page 11 for discs/Page 14 for USB), the aspect ratio may
not be set correctly.
: For “DISC” source and
“USB” source only: The aspect ratio is
automatically selected to match the
incoming signals.
12
ENGLISH
00_KW-V2018ST_M_ENG.indb 12
17/6/2017 7:35:46 AM
USB
Video
2
[
MENU]
[T MENU]
[
[
]
]
Displays the disc menu (DVD).
Displays the disc menu (DVD).
Switches to the direct disc menu mode.
Touch the target item to select.
Displays the menu/scene selection
screen.
• [J] [K] [H] [I]: Selects an item.
• [Enter]: Confirms the selection.
• [Return]: Returns to the previous
screen.
Video playback for VCD
Touching the operation keys performs the following
actions:
1
[
]
[
]
[
]
Refer to “Video playback except VCD” on
page 12.
Connecting a USB device
2
[
MENU]
[
]
[
You can connect a USB mass storage class device such
as a USB memory, digital audio player, etc. to the unit.
• For playable file types and other information, see
pages 46 and 49.
• You cannot connect a PC or portable HDD to the
USB input terminal.
• You cannot connect a USB device via a USB hub.
]*
Displays the disc menu.
USB device (commercially available)
Selects the audio channel
(ST: stereo, L: left, R: right).
Displays or hides the direct selection
buttons.
1 Touch [DIR/CLR] to select a track
directly on a VCD.
2 Touch the numbers ([0], [1] to [9]) to
select the desired track.
3 Touch [Enter] to confirm.
On the rear panel
To delete the last entry, touch [DIR/
CLR].
E.g. Video menu control screen for KW-V440BT
[Return]
Displays the previous screen or menu.
* You need to stop playback to deactivate the PBC function when
playing a VCD with PBC activated.
The source changes to “USB” and playback starts.
• All tracks in the USB device will be played repeatedly
until you change the source or disconnect the USB
device.
ENGLISH
00_KW-V2018ST_M_ENG.indb 13
13
17/6/2017 7:35:46 AM
USB
Selecting a folder/track on the list
Playback operations
Playback information and key operation
• For playback information, see “Source control screen”
on page 7.
• For key operations on the touch panel, see “Common
operation keys on source control screen” on
page 8.
1
2
Display the folder/track list.
Settings for USB playback
On the source control screen, touch as follows:
1
Select the folder (1), then the item (2) in
the selected folder.
2
Display the screen.
On the source control screen, touch as follows:
Make the settings.
Selecting the file type to play
You can specify the file type to play.
Select an item in each layer until you reach and
select the desired file.
E.g. USB source control screen for KW-V440BT
Select the file type as follows:
[Audio]
Plays back audio files.
[Video]
Plays back video files.
[Photo]
Plays back still picture files.
If the USB contains no files of the selected type, the
existing files are played in the following priority: audio,
video, then still picture. You can change these settings
only while playback is stopped.
14
Select the monitor type to watch a wide screen
picture on the external monitor.
16:9 (Initial)
4:3 LB
4:3 PS
• Next: Switch between internal memory and the
memory source of the connected device (such as
a mobile phone).
ENGLISH
00_KW-V2018ST_M_ENG.indb 14
17/6/2017 7:35:46 AM
Android
This unit supports the Android™ application, JVC
Music Play. When you use JVC Music Play via this unit,
you can search for audio files by genre, artist, album,
playlist and song.
• For more information about JVC Music Play, visit
screen.
On the source control screen, touch as follows:
• For playable iPod/iPhone types and other
information, see page 49.
• You cannot watch video.
Bluetooth connection
Pair the iPod/iPhone with this unit via Bluetooth.
(Page 26)
Selecting the playback device via the
connection method
Wired connection
2
Make the settings.
iPod/iPhone iPod/iPhone 30-pin
Lightning model connector model
(commercially available) (commercially available)
See on page 38 for more
information.
Playback operations
Playback information and key operation
• ON (Initial): Shows the artworks of the playing
files.
• OFF: Hides the artworks of the playing files.
• AUTO MODE (Initial): Controls from the unit
(using the JVC Music Play application).
• AUDIO MODE: Controls other media player
applications from the Android device (without
using the JVC Music Play application).
– You can play/pause or skip files from the unit.
USB Audio cable
for iPod/iPhone:
KS-U62 (optional
accessory)
30-pin to USB cable
(accessory of iPod/
iPhone)
• For playback information, see “Source control screen”
on page 7.
• For key operations on the touch panel, see “Common
operation keys on source control screen” on
page 8.
Additional keys operations. Touching the operation
keys performs the following actions:
[
]
Switches the device on screen. (Page 38)
On the rear panel
Selecting an audio file from the menu
1
Display the audio menu.
On the source control screen, touch as follows:
16
ENGLISH
00_KW-V2018ST_M_ENG.indb 16
17/6/2017 7:35:47 AM
iPod/iPhone
Tuner
2
Listening to the radio
Select a category (1), then select a
desired item (2).
Playback information on the source control
screen
KW-V340BT/KW-V340BTM
Select an item in each layer until you reach and
select the desired file.
• Available categories differ depending on the type
of iPod/iPhone.
Settings for iPod/iPhone playback
1
Display the screen.
On the source control screen, touch as follows:
2
Make the settings.
• ON (Initial): Shows the artworks of the playing
files.
• OFF: Hides the artworks of the playing files.
KW-V440BT/KW-V440BTM
1 Displays/hides other available operation keys*
2 Current station frequency
3 Text information
• Touching [ ] scrolls the text if not all of the text
is shown.
• Touching [Radio Text] switches the information
between Radio Text, Radio Text Plus and PTY
code.
4 Displays the preset stations window (Page 19)
5 [P1] – [P5]
• (Touch) Selects a preset station.
• (Hold) Presets the current station.
6 NEWS indicator
7 AF indicator
8 TI indicator
9 Operation keys*
p ST/MONO indicator
The ST indicator lights up when receiving an FM
stereo broadcast with sufficient signal strength.
q Seek mode indicator
w LO.S indicator
e RDS indicator
r EON indicator
The EON indicator lights up when a Radio Data
System station is sending EON signals.
t Selects the band (AM/FM1/FM2/FM3)
y Only for KW-V340BT/KW-V340BTM: Playback
source items shown on the Home screen.
• Touching the playback source item changes the
playback source.
* See “Operation keys on source control screen” on page 18.
ENGLISH
00_KW-V2018ST_M_ENG.indb 17
17
17/6/2017 7:35:47 AM
Tuner
Operation keys on source control screen
• The following explanations state the operation keys
for KW-V440BT, unless stated otherwise.
• The appearance of the operation keys may differ,
however the similar operation keys have the same
operations.
• See also “Common operation keys on source control
screen” on page 8.
[MODE ]*1
1
(Hold) Presets stations automatically.
[MONO]*1
Activates monaural mode for better FM
reception (stereo effect will be lost).
• The MONO indicator lights up while
monaural mode is activated.
• To deactivate, touch [MONO] again.
[TI]*1
18
(For FM RDS features)
Activates TI standby reception mode.
• When TI is activated, the unit is ready
to switch to traffic information if
available. The TI indicator lights up in
white.
• If the TI indicator lights up in orange,
tune into another station providing
Radio Data System signals.
• The volume adjustment for Traffic
Information is automatically
memorized. The next time the unit
switches to Traffic Information, the
volume is set to the memorized level.
• To deactivate, touch [TI] again.
Presetting stations in the memory
You can preset five stations for each band.
9
[PTY]*1*2
Touching the operation keys performs the following
actions:
[SSM ]*1
Change the settings for the selected
tuner reception on
screen. (Page 19)
[SEEK]
[S]/[T]
(For FM RDS features)
Enters PTY search mode.
1 Touch [PTY].
2 Touch and hold a PTY code to search
for.
If there is a station broadcasting a
program of the same PTY code as you
have selected, that station is tuned in.
Changes the seek mode for [S]/[T].
• AUTO1 (Initial): Auto search
• AUTO2: Tunes in preset stations one
after another
• MANU: Manual search
Searches for a station.
• The search method differs according
to the selected seek mode (see above).
Automatic presetting — SSM (Strongstation Sequential Memory) (for FM only)
On the source control screen, touch as follows:
(Hold)
The local stations with the strongest signals are found
and stored automatically.
Manual presetting
1
Tune in to a station you want to preset.
2
Select a preset number to store into.
*1 Appears only when FM is selected as the source.
*2 Only English/Spanish/French/German/Dutch/ Portuguese are
available for the text language here. If another language has
been selected in (Page 38), the text language
is set to English.
(Hold)
E.g. Tuner source control screen for KW-V440BT
The station selected in step 1 is stored into the
preset number [P1] to [P5] you have selected.
ENGLISH
00_KW-V2018ST_M_ENG.indb 18
17/6/2017 7:35:47 AM
Tuner
2
Selecting a preset station
1
Make the settings.
Select the band, then display the preset
station window.
On the source control screen, touch as follows:
2
Select a preset station.
E.g. Preset station window for KW-V440BT
To hide the window: Touch [ ] or [
].
Settings for other FM Radio Data System
features
1
Display the screen.
When driving in an area where FM reception is not
sufficient enough, this unit automatically tunes in
to another FM Radio Data System station of the
same network, possibly broadcasting the same
program with stronger signals— Network-Tracking
Reception.
Select the Network-Tracking Reception mode.
• AF: Switches to another station. The program
may differ from the one currently received. The
AF indicator lights up.
• AF Reg: Switches to another station broadcasting
the same program. The AF indicator lights up.
• OFF (Initial): Deactivates the function.
*
• 00min to 90min: Activates New Standby
Reception by selecting the period of time to
disable the interruption. The NEWS indicator
lights up.
• OFF (Initial): Deactivates the function.
• ON: Tunes in only to FM stations with sufficient
signal strength. The LO.S indicator lights up.
• OFF (Initial): Deactivates the function.
• ON (Initial): Automatically searches for a station
with better reception for traffic information if the
current reception of current station is poor.
• OFF: Deactivates the function.
* The volume adjustment for Traffic Information is automatically
memorized. The next time the unit switches to Traffic
Information, the volume is set to the previous level.
The RDS indicator lights up when the NetworkTracking Reception is activated and an FM Radio
Data System station is found.
On the source control screen, touch as follows:
ENGLISH
00_KW-V2018ST_M_ENG.indb 19
19
17/6/2017 7:35:47 AM
Pandora®
(Only for KW-V340BT Region 4)
You can stream Pandora from iPhone/iPod touch or
Android devices.
• Pandora is only available in certain countries. For
more information, visit .
• Because Pandora is a third-party service, the
specifications are subject to change without
prior notice. Accordingly, compatibility may be
impaired or some or all of the services may become
unavailable.
• Some functions of Pandora cannot be operated from
this unit.
• For issues using the application, contact Pandora at
.
Preparation
Installing the application
Your smartphone must has built in Bluetooth and the
following profiles must be supported:
• SPP (Serial Port Profile)
• A2DP (Advanced Audio Distribution Profile)
Establish an Internet connection using LTE, 3G, EDGE,
or WiFi.
Ensure you are logged in to your smartphone
application. If you do not have a Pandora account, you
can create one for free from your smartphone or at
.
Install the latest version of the Pandora application on
your smartphone.
• For Android devices: Search for “Pandora” in Google
play to find and install the most recent version.
• For iPhone/iPod touch: Search for “Pandora” in the
Apple iTunes App Store to find and install the most
recent version.
Playback operations
Playback information and key operation
Connecting the device
For Android devices
Pair the Android device with this unit via Bluetooth.
(Page 26)
For iPhone/iPod touch
• Via USB input terminal: Connect iPhone/iPod touch
with the cable. (Page 16)
– For Lightning models: Use KS-U62 (optional
accessory).
– For 30-pin connector models: Use 30-pin to USB
cable (accessory of iPod/iPhone).
• Via Bluetooth: Pair the iPhone/iPod touch with this
unit. (Page 26)
Selecting the device
For selecting the playback device via the connection
method to use, see on page
38.
You can also operate Pandora with optional remote
controller, RM-RK258.
You can only control play, pause and skip with the
remote controller.
1 Playing time/playback status
2 Track information
• Touching [H] scrolls the text if not all of the text
is shown.
3 Picture data
4 Playback source items shown on the Home screen.
• Touching the playback source item changes the
playback source.
5 Displays/hides other available operation keys*
6 Operation keys*
* See “Operation keys on source control screen” on page 21.
20
ENGLISH
00_KW-V2018ST_M_ENG.indb 20
17/6/2017 7:35:48 AM
Pandora®
Operation keys on source control screen
• The appearance of the operation keys may differ,
however the similar operation keys have the same
operations.
• See also “Common operation keys on source control
screen” on page 8.
Selecting a station from the list
1
Display the list selection screen.
On the source control screen, touch as follows:
3
Select a station from the list.
On the station list
Pandora
Shuffle
By Date
Station Name
By Name
Station Name
Station Name
Touching the operation keys performs the following
actions:
[
]
Adds the current artist to the station list.
[
]
Adds the current track to the station list.
[
]
Station Name
Switches the device on screen. (Page 38)
6
[
[Station List]
Selects from the station names.
• To play all the songs in the registered stations
randomly, touch [Shuffle].
• To sort the list in reverse chronological order,
touch [By Date].
• To sort the list in alphabetical order, touch [By
Name].
• The
indicator appears on the right of the
item when the station is shared.
[Genre List]
Selects from the genres.
On the genre list
Station List
Genre List
Bookmarks the current track.
]
[
[
Station Name
Select the list type.
Pandora
5
[
2
]
]
]
Displays the list selection screen.
Thumbs down to the current track and
skips to the next track.
Registers the current track as a favorite.
[ I/W ]
Starts/pauses playback.
[T]
Skips the current track.
• Not available when the Pandora skip
reaches its limit.
Pandora
Genre Name 1
Song Name 1
Genre Name 2
Song Name 2
Genre Name 3
Song Name 3
Genre Name 4
Song Name 4
Genre Name 5
Song Name 5
1 Select a genre.
2 Select a station.
The selected station is added to the station list.
ENGLISH
00_KW-V2018ST_M_ENG.indb 21
21
17/6/2017 7:35:48 AM
Spotify
With Spotify, your music is everywhere. Working out,
partying or relaxing, the right music is always at your
fingertips. There are millions of songs on Spotify—from
old favorites to the latest hits. Just choose the music
you love, or let Spotify surprise you.
You can stream Spotify from iPhone/iPod touch or
Android devices.
• Because Spotify is a third-party service, the
specifications are subject to change without
prior notice. Accordingly, compatibility may be
impaired or some or all of the services may become
unavailable.
• Some functions of Spotify cannot be operated from
this unit.
• For issues using the application, contact Spotify at
.
Preparation
Installing the application
Your smartphone must has built in Bluetooth and the
following profiles must be supported:
• SPP (Serial Port Profile)
• A2DP (Advanced Audio Distribution Profile)
Establish an Internet connection using LTE, 3G, EDGE,
or WiFi.
Ensure you are logged in to your smartphone
application. If you do not have an Spotify account, you
can create one for free from your smartphone or at
.
22
Install the latest version of the Spotify application on
your smartphone.
• For Android devices: Search for “Spotify” in Google
play to find and install the most recent version.
• For iPhone/iPod touch: Search for “Spotify” in the
Apple iTunes App Store to find and install the most
recent version.
Playback operations
Playback information and key operation
KW-V340BT/KW-V340BTM
Connecting the device
For Android devices
Pair the Android device with this unit via Bluetooth.
(Page 26)
For iPhone/iPod touch
• Via USB input terminal: Connect iPhone/iPod touch
with the cable. (Page 16)
– For Lightning models: Use KS-U62 (optional
accessory).
– For 30-pin connector models: Use 30-pin to USB
cable (accessory of iPod/iPhone).
• Via Bluetooth: Pair the iPhone/iPod touch with this
unit. (Page 26)
KW-V440BT/KW-V440BTM
Selecting the device
For selecting the playback device via the connection
method to use, see on page
38.
You can also operate Spotify with a remote controller
(supplied/optionally purchased), RM-RK258.
You can only control play, pause and skip with the
remote controller.
ENGLISH
00_KW-V2018ST_M_ENG.indb 22
17/6/2017 7:35:48 AM
Spotify
1 Playing time/playback status
2 Track information
• Touching [H] scrolls the text if not all of the text
is shown.
• Touching [ ]/[ ] changes the displayed
information between artist ( ) and album ( ).
3 Picture data
4 Only for KW-V340BT/KW-V340BTM: Playback
source items shown on the Home screen.
• Touching the playback source item changes the
playback source.
5 Displays/hides other available operation keys*
6 Progress bar
7 Operation keys*
* See “Operation keys on source control screen” below.
Operation keys on source control screen
• The following explanations state the operation keys
for KW-V440BT, unless stated otherwise.
• The appearance of the operation keys may differ,
however the similar operation keys have the same
operations.
• See also “Common operation keys on source control
screen” on page 8.
Touching the operation keys performs the following
actions:
5
[
]*1
Thumbs down to the current track and
skips to the next track.
[
]*1
Registers the current track as a favorite.
[
]*2*3
Activates/deactivates shuffle playback
mode.
[
]*2
Repeats all tracks/cancels the repeat
playback.
[
]*2*3
Repeats the current track/cancels the
repeat playback.
Creates a new station.
]
[
Switches the device on screen. (Page 38)
]
[
Creating your station (Start Radio)
Start Radio is to start a radio channel based on the
currently played track.
Create your station.
On the source control screen, touch as follows:
Station is created and playback starts automatically.
• You can personalize your station using thumb up
([ ]) or thumb down ([ ]).
– You cannot thumb up or down while playing tracks
in a playlist.
– Personalizing stations may not be available
depending on the track.
7
[
Displays the Spotify menu screen.
]
[ ]*3[ ]
[
][
[
]
]
Selects a track.
Starts (I)/pauses (W) playback.
Saves the current track/artist to .
*1 Not available for tracks in a playlist.
*2 Not available for tracks in the Radio.
*3 Available only for premium account users.
ENGLISH
00_KW-V2018ST_M_ENG.indb 23
23
17/6/2017 7:35:48 AM
Spotify
Selecting a track
1
Other External Components
AV-IN
Display the Spotify menu screen.
On the source control screen, touch as follows:
Connecting an external component
See page 46 for more information.
Starting playback
2
Select the list type, then select a desired
item.
The list types displayed differ depending on the
information sent from Spotify.
1
2
Select “AV-IN” as the source.
Turn on the connected component and
start playing the source.
Rear view camera
Install the rear view camera (separately purchased) in
the appropriate position according to the instructions
supplied with the rear view camera.
Connecting a rear view camera
See page 46 for more information.
• To use the rear view camera, a reverse lead (REVERSE)
connection is required. (Page 45)
Using the rear view camera
Changing the AV-IN name
You can change the AV-IN name displayed on the
source control screen.
• This setting does not affect the source name
displayed on the Home screen.
1
Display the screen.
On the source control screen, touch as follows:
• To return to the top layer, touch [ ].
• To return to the upper layer, touch [ ].
2
Select an AV-IN name
• For rear camera settings, see on
page 37.
To display the rear view camera screen
The rear view screen is displayed by shifting the gear
to the reverse (R) position when is set to [ON]. (Page 37)
• A caution message appears on the screen. To
remove the caution message, touch the screen.
You can also display the picture from the rear view
camera manually without shifting the gear to the
reverse (R) position.
On the Home screen, touch as follows:
24
ENGLISH
00_KW-V2018ST_M_ENG.indb 24
17/6/2017 7:35:49 AM
Other External Components
Operations while the camera screen is
displayed
To adjust the picture
Touch the area shown below.
To exit the camera screen
Touch the area shown below or perform the following
to display the Home screen:
• For KW-V340BT/KW-V340BTM: Press HOME on the
monitor panel.
• For KW-V440BT/KW-V440BTM: Press FNC on the
monitor panel, then touch [Home] on the pop-up
short-cut menu.
Video menu control screen is displayed. For details, see
“Video menu control operations” on page 12.
• To exit video menu control screen, touch the same
area again.
To display parking guide line
Set to [ON] (Page 37) or
touch the area shown below.
External navigation unit
(Only for KW-V340BT Region 3, KW-V340BTM
Region 2, KW-V440BT Region 3 (except for
Indonesian models), KW-V440BTM Region 2)
You can connect an external navigation unit
(commercially available) to the NAV input terminal so
that you can view the navigation screen. (Page 46)
• The navigation guidance comes out of the front
speakers even when you are listening to an audio
source.
Viewing the navigation screen
• For settings, see on page 37.
TV tuner box
(Only for KW-V440BT Region 3 (except for
Indonesian models), KW-V440BTM Region 2)
You can connect a TV tuner box (commercially
available) to the REMO OUT output terminal to watch
TV.
• To close the parking guidelines, touch the same area
again.
Connecting a TV tuner box
See page 46 for more information.
Displaying the TV screen
• For settings, see on page 38.
1
2
Select “AV-IN” as the source.
Turn on the TV tuner box.
To change the channels: Touch [ CH J ] or [ CH K ].
Select “Navi” as the source.
On the Home screen, touch as follows:
• While the navigation screen is displayed, the touch
panel operations are available only for navigation.
• The aspect ratio of the navigation screen is fixed
to regardless of the [
] setting.
(Page 12).
To exit the navigation screen
For KW-V340BT Region 3, KW-V340BTM Region 2:
Press
on the monitor panel.
For KW-V440BT Region 3 (except for Indonesian
models), KW-V440BTM Region 2: Touch [
] on the
pop-up short-cut menu.
ENGLISH
03_KW_V340BT_M_Body01.indd 25
25
5/7/2017 4:03:21 PM
Bluetooth®
Information
Bluetooth is a short-range wireless radio
communication technology for mobile devices such as
mobile phones, portable PCs and other devices.
Bluetooth devices can be connected without cables
and communicate with each other.
Note
• While driving, do not perform complicated
operations such as dialing numbers, using the phone
book, etc. When you perform these operations, stop
your car in a safe place.
• Some Bluetooth devices may not connect to this unit
depending on the Bluetooth version of the device.
• This unit may not work for some Bluetooth devices.
• Connecting conditions may vary depending on your
environment.
• For some Bluetooth devices, the device is
disconnected when the unit is turned off.
• If your mobile phone supports PBAP (Phone Book
Access Profile), you can display the following items
on the touch panel when the mobile phone is
connected.
– Phone book
– Dialed calls, received calls, and missed calls (up to
10 entries in total)
Preparation
Connect and install the microphone beforehand. For
details, see page 45.
26
Connection
When you connect a Bluetooth device to the unit for
the first time:
1 Register the device by pairing the unit and the
device.
2 Connect the device to the unit. (Page 27)
Registering a new Bluetooth device
Pairing allows Bluetooth devices to communicate with
each other.
• The pairing method differs depending on the
Bluetooth version of the device.
– For devices with Bluetooth 2.1:
You can pair the device and the unit using SSP
(Secure Simple Pairing) which only requires
confirmation.
– For devices with Bluetooth 2.0:
You need to enter a PIN code both on the device
and unit for pairing.
• Once the connection is established, it is registered in
the unit even if you reset the unit. Up to five devices
can be registered in total.
• Two devices for Bluetooth phone and one for
Bluetooth audio can be connected at a time.
However, when “BT Audio” is selected as the source,
you can connect up to five Bluetooth audio devices
and switch between these five devices.
• To use the Bluetooth function, you need to turn on
the Bluetooth function of the device.
Auto pairing
When is set to [ON], Android or iOS
(such as iPhone) devices are automatically paired
when connected via USB. (Page 31)
Pairing a Bluetooth device using SSP (for
Bluetooth 2.1)
When the Bluetooth device is compatible with
Bluetooth 2.1, a pairing request is sent from the
available device.
1
Search for the unit (“JVC KW-V”) from your
Bluetooth device.
2
Confirm the request both on the device
and the unit.
On the device:
On the unit:
To reject the request: Touch [Cancel].
ENGLISH
00_KW-V2018ST_M_ENG.indb 26
17/6/2017 7:35:49 AM
Bluetooth®
Pairing a Bluetooth device using a PIN code (for
Bluetooth 2.0)
1
4
On the Home screen, touch as follows:
On the screen, touch as
follows:
: [0000]
2
Select the device (1) you want to connect,
then select [Connection] (2).
3
Select the device (1) to connect, then
return to the (2).
Note
• The PIN code is initially set to “0000”.
• The maximum number of digits in the PIN code is 15.
Connecting/disconnecting a registered
Bluetooth device
Change the PIN code.
If you wish to skip changing the PIN code, go to
step 3.
2
• If a PIN code is required, enter “0000” (initial) or
new PIN code you have entered in step 2.
• When pairing is completed, the device is
registered on the screen.
Display the screen.
Then, on the screen, touch as follows:
[System] : [Enter]
Select the unit (“JVC KW-V”) on your
Bluetooth device.
1
Display the screen.
On the Home screen, touch as follows:
Then, on the screen, touch as follows:
[System] : [Enter]
• To delete the last entry, touch [Clear].
• To delete the PIN code, touch and hold [Clear].
3
On the screen, touch as
follows:
: [Enter]
Select [ON] (to connect) or [OFF] (to disconnect).
: Mobile phone
: Audio device
4
Connect the selected device.
Search for the unit (“JVC KW-V”) from your
Bluetooth device.
ENGLISH
00_KW-V2018ST_M_ENG.indb 27
27
17/6/2017 7:35:49 AM
Bluetooth®
• The status is shown as follows:
– : Connection is in progress.
– : A connection has been established.
– : A connection can be
established.
– : Disconnection is in progress.
– : No connection is established.
• When a Bluetooth mobile phone is connected, the
signal strength and battery level are displayed when
the information is acquired from the device.
• For KW-V340BT Region 3, KW-V340BTM Region
2, KW-V440BT Region 3 (except for Indonesian
models), KW-V440BTM Region 2: When receiving
a call during navigation guidance, the screen is
switched automatically.
– To return to the navigation screen, touch [ ].
Making a call
1
On the Home screen, touch [Phone]. (See also
page 6.)
2
When a call comes in...
[
Ends a call.
]
]/
]
[DTMF]
[
Answers a call.
]
]
[
Rejects a call.
• Call information is displayed if acquired.
• Phone operation is not available while the picture
from the rear view camera is displayed.
28
1 From the call history* (missed calls/received
calls/dialed calls)
2 From the phone book*
3 From the preset list (Page 29)
4 Use direct number entry
5 Use voice dialling
Touching the operation keys performs the following
actions:
[
[
Touching the operation keys performs the following
actions:
Select a method to make a call.
During a call...
To delete the registered device: Perform step 1,
select the device you want to delete in step 2, then
touch [Remove].
• A confirmation message appears. Touch [Yes].
Bluetooth mobile phone
Display the phone control screen.
Switches between handsfree mode and
phone mode.
Enters DTMF (Dual Tone Multi
Frequency), then sends text using the
keypad.
NR LEVEL
[–] / [+]
Adjusts the noise reduction level.
(–5 to 5, initial 0)
EC LEVEL
[–] / [+]
Adjusts the echo volume level.
(–5 to 5, initial 0)
MIC LEVEL
[–] / [+]
Adjusts the volume level of the
microphone. (–10 to 10, initial –4)
* Applicable only for mobile phone compatible with PBAP (Phone
Book Access Profile).
3
Select a contact (1), then make a call (2).
When item 1, 2 or 3 is selected in step 2:
• Press + / – buttons on the monitor panel to adjust
the volume of the call or earpiece.
ENGLISH
00_KW-V2018ST_M_ENG.indb 28
17/6/2017 7:35:50 AM
Bluetooth®
To use alphabet search in the phone book
1 Touch [ A-Z].
2 Touch the first letter you want to search for on
the keypad.
To search for a number, touch [1,2,3...].
3 Select a contact you want call from the list.
To display other phone numbers in the same
contact
You can store up to 10 phone numbers per
contact.
1 Touch [ ].
2 Select a contact you want call from the list.
When item 4 is selected in step 2:
Enter the phone number (1), then make a
call (2).
When item 5 is selected in step 2:
Say the name of the person you want to
call.
• Available only when the connected mobile
phone has a voice recognition system.
• If the unit cannot find the target, “Please speak
into the microphone” appears. Touch [Start],
then say the name again.
• To cancel voice dialling, touch [Cancel].
Presetting phone numbers
You can preset up to five phone numbers.
1
Display the phone control screen.
On the Home screen, touch [Phone]. (See also
page 6.)
2
Select call history or phone book calling
method (1), then select a contact (2) to
preset.
3
Select a preset number to store into.
Switching between two connected devices
You can change the device to use when 2 devices are
connected.
On the phone control screen:
The active device is highlighted.
• To enter “+”, touch and hold [0/+].
• To delete the last entry, touch [
].
(Hold)
To delete the contact in the preset number: Touch
[ ] besides the contact on the preset list.
ENGLISH
00_KW-V2018ST_M_ENG.indb 29
29
17/6/2017 7:35:50 AM
Bluetooth®
Bluetooth audio player
KW-V440BT/KW-V440BTM
Additional keys operations. Touching the operation
keys performs the following actions:
[
JVC Streaming DJ
When “BT Audio” is selected as the source, you can
connect up to five Bluetooth audio devices at the
same time. You can easily switch between these five
devices by playing music from the device.
]
Displays screen.
Selecting an audio file from the menu
1
Display the audio menu.
On the source control screen, touch as follows:
KW-V340BT/KW-V340BTM
1 Tag data* (current track title/artist name/album
title)
• Pressing [H] scrolls the text if not all of the text is
shown.
2 Connected device name
• Touching the device name switches to another
connected Bluetooth audio device.
3 Signal strength and battery level
(Appear only when the information is acquired
from the device.)
4 Playing time*/playback status*
2
Select a category (1), then select a
desired item (2).
* Available only for devices compatible with AVRCP 1.3.
Playback information and key operation
• For playback information, see “Source control screen”
on page 7.
• For key operations on the touch panel, see “Common
operation keys on source control screen” on
page 8.
30
Select an item in each layer until you reach and
select the desired file.
ENGLISH
03_KW_V340BT_M_Body01.indd 30
18/7/2017 10:04:53 AM
Settings
Bluetooth®
Bluetooth settings
You can change various settings for using Bluetooth
devices on the screen.
1
Display the screen.
On the Home screen, touch as follows:
Then, on the screen, touch as follows:
[System] : [Enter]
2
Make the settings.
Display the list of registered devices. You can
connect a device or delete registered devices.
Change the PIN code of the unit.
Show the device name of this unit to be shown on
the Bluetooth device — JVC KW-V.
Show the device address of the unit.
• ON (Initial): Automatically establishes a
connection with the last connected Bluetooth
device when the unit is turned on.
• OFF: Cancels.
Display the screen.
Select the speakers used for Bluetooth mobile
phones and Bluetooth audio players.
• Front Only: Front speakers only.
• All (Initial): All speakers.
Then, on the screen, touch [Audio].
Audio settings
On the Home screen, touch as follows:
• ON: The unit answers the incoming calls
automatically in 5 seconds.
• OFF (Initial): The unit does not answer the calls
automatically. Answer the calls manually.
• ON (Initial): Establishes pairing automatically
with the Android or iOS device (such as iPhone)
connected via USB. (Auto pairing may not work
for some devices depending on the Android/iOS
version.)
• OFF: Cancels.
Touch and hold [Enter] to reset all settings you
have made for using Bluetooth mobile phones and
Bluetooth audio players.
E.g. Audio settings screen for KW-V440BT
You cannot change the screen in the
following situations:
• When the AV source is turned off.
• When the Bluetooth phone is used (making or
receiving a call, during a call, or while voice dialling).
• During navigation guidance.
The following adjustments are memorized for each
source until you adjust the sound again. If the source
is a disc, the adjustments are stored for each of the
following categories.
• DVD/VCD
• CD
• DivX/MPEG1/MPEG2/MP3/WMA/WAV/AAC/FLAC
You cannot adjust the sound when the unit is in
standby.
ENGLISH
03_KW_V340BT_M_Body01.indd 31
31
5/7/2017 4:04:10 PM
Settings
Adjust the sound as follows:
Selecting a preset sound mode
Select a preset sound mode on the
screen.
• Flat (Initial)/Hard Rock/Pop/Hip Hop/R&B/Jazz/
Classical/drvn 3/drvn 2/drvn 1/User
Adjusts the width of the frequency.
• 1.35/1.5 (Initial)/2.0
Activates/deactivates bass.
• ON/OFF (Initial)
Adjusts the subwoofer level.*
• –50 to +10 (Initial: 0)
• To clear the adjustment, touch [EQ INIT].
• To apply the adjusted equalizer to all playback
sources, touch [ALL SRC], then touch [OK] to
confirm.
Store your own sound adjustments
1
2
3
Repeat step 2 to adjust the level of other
bands.
* Not adjustable when is selected for subwoofer on the
screen. (Page 33)
Select a preset sound mode.
Select a band (1) and adjust the level (2),
then adjust the sound (3).
Adjust the sound effect.
Adjusts loudness.
• OFF (Initial)/Low/High
Selects the bass boost level.
• OFF (Initial)/Level 1/Level 2/Level 3/Level 4/
Level 5
Reduces the driving noise by raising the bandwidth.
• OFF (Initial)/ON
32
*1
Virtually enhances the sound space using the Digital
Signal Processor (DSP) system. Select the enhance
level.
• OFF (Initial)/Small/Medium/Large
*2
Restores the sound lost due to audio compression to a
realistic sound.
• OFF/ON (Initial)
Virtually makes the sound more realistic using the
Digital Signal Processor (DSP) system. Select the sound
level.
• OFF (Initial)/Level 1/Level 2/Level 3
Moves the center of the sound to the lower or higher
point. Select the height.
• OFF (Initial)/Low/Middle/High
*1 You cannot change the setting when “Tuner” is selected as the
source.
*2 This function works only when “DISC”/ “USB”/ “iPod”/
“Android™” is selected as the source.
Touch [J]/[K]/[H]/[I] or drag the
mark to adjust.
Adjusts the front and rear speaker output balance.
When using a two-speaker system, set the fader to the
center (0).
• F15 to R15 (Initial: 0)
ENGLISH
00_KW-V2018ST_M_ENG.indb 32
17/6/2017 7:35:51 AM
Settings
Adjusts the left and right speaker output balance.
• L15 to R15 (Initial: 0)
To clear the adjustment: Touch [Center].
Setting the speakers and crossover
frequency
1
Select a car type (1), select the location
of the speakers (2)*, then display the
screen (3).
Preparation:
Before making the adjustment for ,
select the appropriate crossover network mode
according to the speaker system (2-way speaker
system or 3-way speaker system).
1
* Speaker location selection is available only when
is set to [2way].
On the monitor panel, press the following buttons
at the same time:
• For KW-V340BT/KW-V340BTM: and
• For KW-V440BT/KW-V440BTM:
FNC and – (volume)
3
• Adjustable items vary depending on the selected
speaker type/speaker size/crossover settings.
/
Adjusts the output volume of the tweeter (left/
right).
Adjusts the output volume of the selected speaker.
Turn off the AV source.
Display the screen.
Adjust the crossover frequency of the
selected speaker.
Adjusts the crossover frequency for the tweeter.
On the Home screen, touch as follows:
2
3
2
Select the speaker type (1), select the size
of the selected speaker (2), then display
the screen (3).
Adjusts the crossover frequency for the front or rear
speakers (high pass filter).
Adjusts the crossover frequency for the speaker
(low pass filter).
//
Adjusts the crossover slope.
Selects the phase for the speaker.
Select the crossover network mode.
[2way]
Select this when 2-way system
speakers are used (front/rear).
[3way]
Select this when 3-way system
speakers are used (tweeter/mid
range/woofer).
A confirmation message appears. Touch [Yes].
• If a speaker is not connected, select .
• When setting the front speakers, also select the
speaker size for .
ENGLISH
00_KW-V2018ST_M_ENG.indb 33
33
17/6/2017 7:35:51 AM
Settings
Make fine adjustments to the delay time of the speaker
output to create a more suitable environment for your
car.
Select the listening position (1), select
[Distance] or [Gain](2) to make an
adjustment, then adjust each speaker setting
(3).
1 Select from , , or
*.
2 Select an item to adjust.
[Distance]
Adjusts the digital time alignment
value.
[Gain]
Adjusts the output volume of the
selected speaker.
3 To determine the adjustment value, see the
following “Determining the value for adjustment”.
To initialize the setting value: Touch [Initialize].
Determining the value for
adjustment
If you specify the distance from the center of the
currently set listening position to every speaker, the
delay time will be automatically computed and set.
1 Determine the center of the currently set
listening position as the reference point.
2 Measure the distances from the reference point
to the speakers.
3 Calculate the differences between the distance of
the furthest speaker and other speakers.
4 Set the DTA value calculated in step 3 for
individual speakers.
5 Adjust gain for individual speakers.
E.g. When is selected as the listening
position
On the Home screen, touch as follows:
+90 cm
Adjust and store the auto-adjustment volume level for
each source. If the source is a disc, the adjustment is
stored for each of the following categories:
• DVD/VCD
• CD
• DivX/MPEG1/MPEG2/MP3/WMA/WAV/AAC/FLAC
The volume level will automatically increase or
decrease when you change the source.
• –15 to +6 (Initial: 00)
Display settings
Display the screen.
Then, on the screen, touch [Display].
60 cm
80 cm
150 cm
+70 cm
E.g. Display settings screen for KW-V440BT
+0 cm
* is selectable only when is set to
[2way].
34
ENGLISH
00_KW-V2018ST_M_ENG.indb 34
17/6/2017 7:35:51 AM
Settings
• Auto (Initial): Dims the screen and button
illumination when you turn on the headlights.
– Connection to the car light control switch is
required. (Page 45)
• ON: Activates dimmer.
• OFF: Deactivates dimmer.
• The selectable background designs differ depending
on the selected Home screen design.
• When the Home screen design is changed, source
icon designs are also changed.
2 Change the background design
Display the background design selection screen (1),
select the dimmer setting (2) ([ ]: dimmer on or
[ ]: dimmer off), then select the background design
(3).
You can change the display design. While playing a
video or picture, you can capture an image and use
the captured image as a background.
• You cannot capture copyrighted content and images
from iPod/iPhone.
• When using a JPEG file as the background, make sure
that the resolution is 800 x 480 pixels.
• The color of the captured image may look different
from that of the actual scene.
For KW-V340BT/KW-V340BTM
1 Change the Home screen design
Display the Home screen design selection screen (1),
then select the Home screen design (2).
3 Change the illumination color of the buttons on
the monitor panel
Display the illumination color selection screen (1),
select the dimmer setting (2) ([ ]: Dimmer on or
[ ]: Dimmer off), then select the illumination color
(3).
• You can also adjust the color yourself. Touch [Edit] to
display the color adjustment screen, then select the
dimmer setting and adjust the color. The adjustment
is saved in [User].
• Selecting [Scan] changes the illumination color
gradually.
For KW-V440BT/KW-V440BTM
1 Change the background design
Display the background design selection screen (1),
then select the background design (2).
When the one of these is selected, you can
change the background color.
2 Change the illumination color of the
background design
Display the background color selection screen (1),
then select the background color (2).
ENGLISH
00_KW-V2018ST_M_ENG.indb 35
35
17/6/2017 7:35:51 AM
Settings
• You can also adjust the color yourself. Press [Adjust]
to display the color adjustment screen, then adjust
the color. The adjustment is saved on [User].
Storing your own scene for the background
image
1
2
3 Change the source icon design
Display the icon style selection screen (1), then select
the icon design (2).
3
While playing a video or picture, display
the screen.
A confirmation message appears. Touch [Yes]
to store the newly captured image. (The existing
image is replaced with the new one.)
• To return to the previous screen, touch [No].
• To cancel the capture, touch [Cancel].
On the screen, touch as follows:
: [Enter]
* Not displayed when playing an external component connected to
the AV-IN input terminal.
Display the background design selection
screen, then touch the following:
• For KW-V340BT/KW-V340BTM: [
Capture]
• For KW-V440BT/KW-V440BTM: [User1 Select] or
[User2 Select]
• ON: Displays the clock while a video source is
playing.
• OFF (Initial): Cancels.
Adjust the image (1), then capture the
image (2).
• ON (Initial)*: Activates the display demonstration.
• OFF: Deactivates the display demonstration.
* For Indonesian models, the initial is .
E.g. Image adjustment screen for KW-V440BT
[J][K][H][I] Moves the zooming frame.
[
]
[IW]*
[
36
]*
• ON: Scrolls the displayed information repeatedly.
• Once (Initial): Scrolls the displayed information once.
• OFF: Cancels.
Touching [H] scrolls the text regardless of this setting.
Magnifies the scene.
• ///
Starts/pauses playback.
Advances scenes frame by frame.
ENGLISH
00_KW-V2018ST_M_ENG.indb 36
17/6/2017 7:35:52 AM
Settings
Adjust the brightness and blackness of the screen.
Select [DIM ON] (dimmer on) or [DIM OFF] (dimmer
off), then change the following settings:
Adjusts brightness.
• –15 to +15 (Initial: 0 for dimmer on, +15 for dimmer
off)
Input settings
Display the screen, touch [Input].
Adjust the parking guidelines according to the size of
the car, parking space and so on.
When adjusting the parking guidelines, make sure to
use the parking brake to prevent the car from moving.
Select the
mark (1), then adjust the position of the
selected
mark (2).
Adjusts blackness.
• –10 to +10 (Initial: 0)
Initialize
Select the color system of the external monitor.
• NTSC/PAL (Initial)
“Please Power Off” appears when the setting is
changed. Turn off the power, then turn on to enable
the change.
Select the viewing angle in relation to the monitor
panel to make the panel easier to see.
• Under 0° (Initial)/5°/10°/15°/20°
E.g. Input settings screen for KW-V440BT
Configure the rear view camera settings.
• ON (Initial): Displays the picture from the rear view
camera when you shift the gear to the reverse (R)
position.
– A caution message appears on the screen. To
remove the caution message, touch the screen.
• OFF: Select this when no camera is connected.
• ON (Initial): Displays the parking guidelines.
• OFF: Hides the parking guidelines.
Make sure that A and B are horizontally parallel, and
that C and D are the same length.
• Touch and hold [Initialize ] for 2 seconds to set all
the marks to the initial default position.
(Only for KW-V340BT Region 3, KW-V340BTM
Region 2, KW-V440BT Region 3 (except for Indonesian
models), KW-V440BTM Region 2)
Change the settings for displaying the screen of an
external navigation unit.
• To change the setting, turn off the AV source by
touching [AV Off] on the Home screen beforehand.
ENGLISH
00_KW-V2018ST_M_ENG.indb 37
37
17/6/2017 7:35:52 AM
Settings
Select which front speakers are used for the navigation
guidance.
• Lch: Output from front left channel only.
• Rch: Output from front right channel only.
• L+Rch (Initial): Output from both front left and front
right channels.
0 to 35: Adjust the volume of the navigation guidance.
System settings
Display the screen.
On the Home screen, touch as follows:
E.g. System settings screen for KW-V440BT
1
Select the device type (1), then touch
[Change] (2).
2
Select the connection method (1), then
confirm the selection ([OK] or [Next]) (2).
If [iPod/iPhone] is selected in step 1:
(Only for KW-V440BT Region 3 (except for Indonesian
models), KW-V440BTM Region 2)
38
Specify the connection method of Android/iPod/
iPhone.
Then, on the screen, touch [System].
Select the text language used for on-screen
information. For details, see “Initial settings” on
page 4.
• ON: Enables to control TV operation on the “AV-IN”.
• OFF (Initial): Select this to use “AV-IN” with the other
component than TV Tuner.
Set the clock. For details, see “Clock settings” on
page 5.
[USB 1 Wire]
Select this when the device is
connected via the USB input
terminal (on the monitor panel or
cable from the rear panel).
[Bluetooth]
Select this when the device is
connected via Bluetooth. (Go to
step 3.)
ENGLISH
04_KW_V340BT_M_Body02.indd 38
5/7/2017 4:05:52 PM
Settings
If [Android/Other] is selected in step 1:
The screen appears. Go to
step 3.
3
When selecting [Bluetooth] as the
connection method: Select the device (1),
then press [OK] (2) to connect.
• If the device is already connected, skip step 1.
• ON (Initial): Activates the key-touch tone.
• OFF: Deactivates the key-touch tone.
(Only for KW-V340BT Region 3, KW-V340BTM
Region 2, KW-V440BT Region 3 (except for Indonesian
models), KW-V440BTM Region 2)
Displays the serial number.
Memorize, recall, or clear the settings you have made.
• The memorized settings are kept even when the unit
is reset.
Touch [Yes] to display the setting screen, then select
an operation:
• Recall: Recalls the memorized settings.
• Memory: Memorizes the current settings.
• Clear: Clears the currently memorized settings.
• Cancel: Cancels.
Touch the center of the marks at the upper left (1),
the lower center (2), then the upper right (3) as
instructed.
Adjust the touch positions of the buttons on the
screen.
A confirmation message appears. Touch [Yes].
Configure settings for using a Bluetooth device, such
as connection and other general operations. For
details, see “Bluetooth settings” on page 31.
This unit has its own Registration Code. Once you
have played back a file with the Registration Code
recorded, this unit’s Registration Code is overwritten
for copyright protection.
• Touch [Enter] to display the information.
• To return to the previous screen, touch [OK].
• To reset the touch position, touch [Reset].
• To cancel the current operation, touch [Cancel].
Initialize all settings you have made. Touch and hold
[Enter] to initialize the settings.
• After initializing the settings, adjust the settings on
the screen.
ENGLISH
00_KW-V2018ST_M_ENG.indb 39
39
17/6/2017 7:35:53 AM
Settings
Assign functions to the keys of the remote controller
on the steering wheel.
• This function is available only when your car is
equipped with the electrical steering remote
controller.
• You can only register/change the functions while
you are parked.
• If your steering remote controller is not compatible,
learning may not be completed and an error
message may appear.
1
Touch [Set] for to display the setting screen.
2
Press and hold a button on the steering
remote controller to register or change.
3
Select a function to assign to the selected
button.
Sterring Remote Control Setting
Please select the function to assign to the button.
VOL
VOL
ATT
Done
SRC
4
Repeat steps 2 and 3 to register other
buttons.
5
Touch [Done] to finish procedure.
40
• The unit can register/change all of the buttons’
functions at the same time. To do this, press all
buttons in turn and after pressing all of them, touch
[Done] on the
screen. However, new functions cannot be learned
after this operation.
• When changing the functions already learned, touch
the assigned function you want to change in step 3
and then touch to select the new function from the
function list.
• Confirm the contents of the settable functions in the
function list. You cannot edit the function list.
To initialize the setting: Touch [Initialize] for
.
• A confirmation message appears. Touch [Yes].
– To cancel the initialization, touch [No].
Updates the system application.
Updates the system.
Updates the DVD system application.
The system update starts. It may take a while.
If the update has been completed successfully,
“Update Completed” appears, then reset the unit.
• Do not disconnect the USB device while updating.
• If the update has failed, turn the power off and then
on, and retry the update.
• Even if you have turned off the power during the
update, you can restart the update after the power
is turned on. The update will be performed from the
beginning.
Update the system by connecting a USB device
containing an update file.
• To obtain the update file, visit
Shows the Open Source Licenses.
Connect a USB device with the update file to the unit.
ENGLISH
00_KW-V2018ST_M_ENG.indb 40
17/6/2017 7:35:53 AM
Remote Controller
Remote controller, RM-RK258, is supplied for
KW-V340BT Region 3, KW-V340BTM Region 2,
KW-V440BT Region 3, KW-V440BTM Region 2.
• For KW-V340BT Region 4: To use the remote
controller, purchase optional remote controller,
RM-RK258.
WARNINGS
Preparation
Removing the battery sheet
Pull the battery sheet out from the remote controller
to activate the battery.
Refer to the instruction manual that comes with the
remote controller.
Changing the battery of the remote
controller
• Do not ingest the battery, as it presents a
chemical burn hazard
The remote controller supplied with this product
contains a coin/button cell battery.
If the coin/button cell battery is swallowed, it can
cause severe internal burns in just 2 hours and can
lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely,
stop using the product and keep it away from
children.
If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medical attention.
CAUTION
CR2025 (+side)
• Use a commercially available button battery
(CR2025).
• Insert the battery with the + and – poles aligned
properly.
– If the effectiveness of the remote controller
decreases, replace the battery.
• Do not leave the battery near fire or under direct
sunlight. A fire, explosion or excessive heat
generation may result.
• Do not set the remote controller in hot places such
as on the dashboard.
• Danger of explosion if Lithium battery is incorrectly
replaced. Replace only with the same or equivalent
type.
* Remote sensor
DO NOT expose the remote sensor to bright light (direct sunlight
or artificial lighting).
ENGLISH
04_KW_V340BT_M_Body02.indd 41
41
18/7/2017 10:26:49 AM
Remote Controller
Aim the remote controller directly at the remote
sensor on the unit. (Page 41)
Basic operations
ATT
Attenuates/restores the sound.
DISP
Displays the current source control
screen.
FM/J /AM/K
• Selects the band.
• Selects a title/item/folder.
• Tuner:
– Searches for stations
automatically. (Press)*
– Searches for stations manually.
(Hold)*
• Selects a track. (Press)
/
VOL +/VOL –
42
SRC
Selects the source.
I/W
• Starts/pauses playback.
• Tuner: Changes the seek mode
(AUTO1, AUTO2, MANU).
2
Press a number button to select a desired
item (station frequency/chapter/title/
folder/file/track).
• To erase a misentry, press CLR.
Answers incoming calls.
3
0–9
Enters a number.
To exit the search mode: Press DIRECT.
1–5
Enters a preset station number.
ANGLE
Not used for this unit.
ASPECT
Changes the aspect ratio.
• To check the current aspect ratio
setting, operate on the touch panel.
(Page )
DIRECT
Enters direct search mode.
CLR
Erases the misentry.
* The search method differs according to the selected seek mode.
Searching for an item directly
While listening to the Tuner or during disc playback,
you can search for a station frequency/chapter/title/
folder/file/track directly using the number buttons.
• To search for a track from the VCD menu, perform
during PBC playback.
1
Press ENT to confirm.
JVC Remote APP
JVC Remote is an application that connects and
controls compatible JVC car receivers via Bluetooth®
like a wireless remote control.
You can also operate this unit from a Smartphone
using JVC Remote APP.
This application can display the source information
of this unit on the smartphone’s screen, and enables
the user to make an audio setting using the graphic
user interface of this application.
This application also works as a free standalone
music player application, when your Smartphone is
not connected to this unit.
• For details, visit
. (Page 4)
Remove the key from the ignition and
disconnect the · battery.
2
Make the proper input and output wire
connections for each unit.
3
Connect the speaker wires of the wiring
harness.
4
Connect the wires of the wiring harness
in the following order: ground, battery,
ignition.
5
6
Connect the wiring harness to the unit.
(Only for KW-V340BT Region 3, KW-V340BT Region 2,
KW-V340BTM Region 4)
Installing the unit
Installing using the mounting brackets
removed from the car
Select the appropriate type of screw for the mounting
brackets: flat head ([) or round head (“).
Installation procedure
1
Installing the trim plate
Press the reset button on the monitor
panel. (Page 3)
Car bracket
[ or “
[ or “
Installing in Toyota cars
Install onto the car bracket using the supplied screws
(“). Use the mounting holes (A or B) that fit the car
bracket.
Side view
Install the unit in your car.
Make sure that the unit is installed securely in place.
If the unit is unstable, it may malfunction (e.g., the
sound may skip).
44
ENGLISH
00_KW-V2018ST_M_ENG.indb 44
17/6/2017 7:35:54 AM
Installation and Connection
Wiring connection
*1 Only for KW-V340BT Region 3, KW-V340BTM
Region 2, KW-V440BT Region 3 (except
for Indonesian models) and KW-V440BTM
Region 2.
*2 Only for KW-V440BT Region 3 (except for
Indonesian models) and KW-V440BTM
Region 2.
10 A fuse
*2
Connect the antenna cord to the antenna terminal
USB input terminal (1 m)
*1 *2
Purple with white stripe
REVERSE
Light green
¥
PRK SW
To the car’s reverse lamp harness when using the optional rear view camera
To the car’s parking brake detection switch harness
(For best safety, be sure to connect the parking sensor.)
Extension wire ( ø )
White ] / White with black stripe [
To front speakers (left) / Mid-range speakers (left) for 3-way crossover
Gray ] / Gray with black stripe [
To front speakers (right) / Mid-range speakers (right) for 3-way crossover
Green ] / Green with black stripe [
To rear speakers (left) / Tweeters (left) for 3-way crossover
Purple ] / Purple with black stripe [
To rear speakers (right) / Tweeters (right) for 3-way crossover
Orange with white stripe
To the car light control switch
Light blue with yellow stripe
STEERING WHEEL
REMOTE INPUT
REMOTE CONT
Blue with white stripe (12 V
Red (Ignition wire)
Yellow (Battery wire)
350 mA)
ANT.CONT
P.CONT
To the OE remote adapter (not supplied) which is compatible with your car
To the power control terminal when using the optional power amplifier (Or)
To the control terminal of the motor antenna or to the power terminal for the booster amplifier of film-type antenna
Ignition key switch
Car fuse
Black (Ground wire)
To the car chassis
Car battery
ENGLISH
00_KW-V2018ST_M_ENG.indb 45
45
17/6/2017 7:35:54 AM
References
Installation and Connection
Connecting external components
1 Navigation input (NAV)*1
2 3rd party TV output (REMO OUT)*2
3 Steering wheel remote controller input (REMO-IN)
• Connect to the vehicle’s steering remote harness
using the Steering Remote cable (]). Contact
your JVC dealer for details.
4 Microphone input (MIC) (Page 45)
5 Audio video input (AV-IN)
Connect the following type of 4-pole mini plug:
1 Left audio
2 Right audio
3 Ground
4 Composite video
6 Video output (V-OUT)
7 Rear view camera input (R-CAM)
46
8 Output terminals*3
• Left output (White)
• Right output (Red)
REAR: Rear speaker preouts
FRONT: Front speaker preouts
SW: Subwoofer preouts
For 3-way crossover:
REAR: Tweeter preouts
FRONT: Mid range speaker preouts
SW: Woofer preouts
*1 Only for KW-V340BT Region 3, KW-V340BTM Region 2,
KW-V440BT Region 3 (except for Indonesian models),
KW-V440BTM Region 2.
*2 Only for KW-V440BT Region 3 (except for Indonesian models),
KW-V440BTM Region 2.
*3 When connecting an external amplifier, connect its ground wire
to the chassis of the car; otherwise the unit may be damaged.
Maintenance
Cleaning the unit
• Do not use any solvent (for example, thinner,
benzine, etc.), detergent, or insecticide. This may
damage the monitor or the unit.
• Gently wipe the panel with a soft, dry cloth.
Handling discs
• Do not touch the recording surface of the disc.
• Do not stick tape etc. on the disc, or use a disc with
tape stuck on it.
• Do not use any accessories for the disc.
• Clean from the center of the disc and move outward.
• Clean the disc with a dry silicone or soft cloth. Do not
use any solvents.
• When removing discs from this unit, pull them out
horizontally.
• Remove burrs from the center hole and disc edge
before inserting a disc.
More information
About playable files
Audio files
• This unit can play back the following files with
following codec and extension code:
– For disc: MP3 (.mp3), WMA (.wma), WAV (.wav),
AAC (.m4a)
– For USB mass storage class device: MP3 (.mp3),
WMA (.wma), WAV (.wav), AAC (.aac, .m4a),
FLAC (.flac)
ENGLISH
00_KW-V2018ST_M_ENG.indb 46
17/6/2017 7:35:54 AM
References
• This unit can play back files that meet the conditions
below:
– Bit rate:
MP3: 8 kbps – 320 kbps
WMA: For disc: 5 kbps – 320 kbps
For USB : 32 kbps – 192 kbps
AAC: 16 kbps – 320 kbps
– Sampling frequency:
MP3: 16 kHz – 48 kHz
WMA: 8 kHz – 48 kHz
WAV: 44.1 kHz
AAC: 32 kHz – 48 kHz
FLAC: 8 kHz – 96 kHz
– Files recorded in VBR (variable bit rate), and have a
discrepancy in elapsed time indication
• This unit can show or display the following:
– Tag:
MP3: ID3 Tag (version 1.0/1.1/2.2/2.3/2.4)
WMA Tag
WAV Tag
AAC Tag
FLAC Tag
– Jacket picture:
Picture size: 32 × 32 to 1 232 × 672 resolution
Data size: less than 500 KB
File type: JPEG
• This unit cannot play back the following files:
– MP3 files encoded with MP3i and MP3 PRO format.
– MP3 files encoded with Layer 1/2.
– WMA files encoded with lossless, professional, and
voice format.
– WMA files which are not based upon Windows
Media® Audio.
– WMA/AAC files copy-protected with DRM.
– AAC files copy-protected with FairPlay (except
those stored on an iPod/iPhone).
– Files which have data such as AIFF, ATRAC3, etc.
Video files
• This unit can play back the following files with
following codec and extension code:
– DivX (.divx, .div, .avi) regardless of the letter case—
upper/lower
– MPEG1/MPEG2 (.mpg, .mpeg)
• Streams that conform to:
– DivX:
Audio: MP3 or Dolby Audio
– MPEG1/MPEG2:
Audio: MPEG1 Audio Layer-2 or Dolby Audio
Video: MPEG system/program stream
• Other playable conditions:
– DivX: Bit rate: 8 Mbps (maximum for average video
signals)
– MPEG1/MPEG2: File format: MP@ML (Main Profile at
Main Level)/SP@ML (Simple Profile at Main Level)/
MP@LL (Main Profile at Low Level)
– Maximum video file size: 2 GB
• This unit cannot play back the following files:
– DivX files encoded in the interlaced scanning
mode.
Picture files
• This unit can play back the following files with
following codec and extension code:
– JPEG (.jpg, .jpeg)
• Other playable conditions:
– Resolution: 32 × 32 to 8 192 × 7 680 (It may take
time to display the file depending on its resolution.)
– Baseline JPEG files
• This unit cannot play back the following files:
– Progressive JPEG files
– Lossless JPEG files
About disc playback
Playable disc types
• CD-DA: Audio CD, CD Text
• DVD Video: Region code: 2, 3 or 4 (depending on the
country and sales area)
• Dual Disc: DVD side
• VCD: Video CD (PBC compatible)
• DVD Recordable/Rewritable (DVD-R/-RW, +R/+RW)
– DVD Video: UDF bridge
– ISO 9660 level 1, level 2, Romeo, Joliet
– Other playable formats:
DVD-R recorded in multi-border format (except for
dual layer discs)
Finalized +R/+RW (Video format only)
• CD Recordable/Rewritable (CD-R/-RW):
– ISO 9660 level 1, level 2, Romeo, Joliet
• Other informations:
– While playing a DVD Video, DTS sound cannot be
reproduced or emitted from this unit.
– This unit can recognize a total of 5 000 files and
250 folders (a maximum of 999 files per folder) in a
recordable/rewritable disc.
– Use only “finalized” recordable/rewritable discs.
– This unit can play back multi-session recordable/
rewritable discs; however, unclosed sessions will be
skipped while playing.
ENGLISH
04_KW_V340BT_M_Body02.indd 47
47
5/7/2017 4:07:07 PM
References
Unplayable disc types and formats
• DVD-Audio/DVD-ROM discs
• SVCD (Super Video CD), CD-ROM, CD-I (CD-I Ready),
DTS-CD
• MPEG4/DivX/AAC (.aac)/FLAC/MKV/DVD–VR/
DVD+VR/DVD-RAM recorded on DVD-R/RW or
+R/+RW
• MPEG4/DivX/AAC (.aac)/FLAC/MKV recorded on
CD-R/RW
• DVD-RW dual layer discs
• +RW double layer discs
• Non-DVD side of a “DualDisc” which does not comply
with the “Compact Disc Digital Audio” standard
• Discs that are not round.
• Discs with coloring on the recording surface or discs
that are dirty.
• Recordable/Rewritable discs that have not been
finalized.
• 8 cm discs. Attempting to insert these discs using an
adapter may cause a malfunction.
• Some recordable/rewritable discs or files may not be
played back due to their characteristics or recording
conditions.
48
Language codes (for DVD language selection)
AA Afar
GD Scots Gaelic
AB Abkhazian
GL Galician
AF Afrikaans
GN Guarani
AM Ameharic
GU Gujarati
AR Arabic
HA Hausa
AS Assamese
HI Hindi
AY Aymara
HR Croatian
AZ Azerbaijani
HU Hungarian
BA Bashkir
HY Armenian
BE Byelorussian
IA Interlingua
BG Bulgarian
IE
Interlingue
BH Bihari
IK Inupiak
BI Bislama
IN Indonesian
BN Bengali, Bangla
IS
Icelandic
BO Tibetan
IW Hebrew
BR Breton
JA Japanese
CA Catalan
JI
Yiddish
CO Corsican
JW Javanese
CS Czech
KA Georgian
CY Welsh
KK Kazakh
DZ Bhutani
KL Greenlandic
EL Greek
KM Cambodian
EO Esperanto
KN Kannada
ET Estonian
KO Korean (KOR)
EU Basque
KS Kashmiri
FA Persian
KU Kurdish
FI
Finnish
KY Kirghiz
FJ Fiji
LA Latin
FO Faroese
LN Lingala
FY Frisian
LO Laothian
GA Irish
LT Lithuanian
LV
MG
MI
MK
ML
MN
MO
MR
MS
MT
MY
NA
NE
NO
OC
OM
OR
PA
PL
PS
QU
RM
RN
RO
RW
SA
SD
SG
SH
SI
SK
SL
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay (MAY)
Maltese
Burmese
Nauru
Nepali
Norwegian
Occitan
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Quechua
Rhaeto-Romance
Kirundi
Rumanian
Kinyarwanda
Sanskrit
Sindhi
Sangho
Serbo-Croatian
Singhalese
Slovak
Slovenian
SM
SN
SO
SQ
SR
SS
ST
SU
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Wolof
Xhosa
Yoruba
Zulu
ENGLISH
00_KW-V2018ST_M_ENG.indb 48
17/6/2017 7:35:54 AM
References
About USB playback
Important
Make sure all important data has been backed up to
avoid losing the data.
We bear no responsibility for any loss of data stored in
the devices while using this unit.
Playable files on a USB device
• This unit can play the following types of files stored
in a USB mass storage class device.
– JPEG/Divx/MPEG1/MPEG2/MP3/WMA/WAV/AAC
(.aac/.m4a)/FLAC
• This unit can recognize:
– A total of 5 000 files
– 250 folders for video files and a maximum of 999
files per folder
– 250 folders for photo files and a maximum of 999
files per folder
– 999 folders for audio files and a maximum of 999
files per folder
• The maximum number of characters (when the
characters are 1 byte):
– Folder names: 50 characters
– File names: 50 characters
Notes on using a USB device
• Avoid using the USB device if it might affect driving
safety.
• When connecting with a USB cable, use a USB 2.0
cable.
• Electrostatic shock at connecting a USB device may
cause abnormal playback of the device. In this case,
disconnect the USB device then reset this unit and
the USB device.
• Do not pull out and connect the USB device
repeatedly while “Reading” is shown on the screen.
• Operation and power supply may not work as
intended for some USB devices.
• Do not leave a USB device in the car, or expose to
direct sunlight or high temperatures to prevent
deformation or damage to the device.
Unplayable USB device
• This unit may not play back files in a USB device
properly when using a USB extension cable.
• USB devices equipped with special functions such as
data security functions cannot be used with the unit.
• Do not use a USB device with 2 or more partitions.
• Depending on the shape of the USB devices and
connection ports, some USB devices may not be
attached properly or the connection might be loose.
• This unit may not recognize a memory card inserted
into a USB card reader.
About iPod/iPhone
Important
Make sure all important data has been backed up to
avoid losing the data.
We bear no responsibility for any loss of data stored in
the devices while using this unit.
iPod/iPhone that can be connected
• Via the USB terminal:
Made for
– iPod nano (7th Generation)
– iPod touch (6th Generation)
– iPod touch (5th Generation)
– iPhone 7 Plus
– iPhone 7
– iPhone SE
– iPhone 6S Plus
– iPhone 6S
– iPhone 6 Plus
– iPhone 6
– iPhone 5S
– iPhone 5C
– iPhone 5
– iPhone 4S
• Via Bluetooth:
Made for
– iPod touch (6th Generation)
– iPod touch (5th Generation)
– iPhone 7 Plus
– iPhone 7
– iPhone SE
– iPhone 6S Plus
– iPhone 6S
– iPhone 6 Plus
– iPhone 6
– iPhone 5S
– iPhone 5C
– iPhone 5
– iPhone 4S
ENGLISH
00_KW-V2018ST_M_ENG.indb 49
49
17/6/2017 7:35:54 AM
References
Notes on using an iPod/iPhone
• When operating an iPod/iPhone, some operations
may not be performed correctly or as intended. In
this case, visit the following JVC web site:
is set to [AUDIO MODE],
launch any media player application on the
Android device and start playback.
No sound comes out of the speakers.
Disconnect the iPod/iPhone, then connect it again.
Select another source, then reselect “iPod”.
Sound output only from the Android device.
When is set to [AUDIO MODE],
relaunch the current media player application or
use another media player application.
Restart the Android device.
If this does not solve the problem, the connected
Android device is unable to route the audio signal
to unit.
Cannot play back when is set to
[AUTO MODE].
Make sure JVC Music Play APP is installed on the
Android device.
Reconnect the Android device and select the
appropriate control mode.
If this does not solve the problem, the connected
Android device does not support the Auto Mode.
“NO DEVICE” or “READING” keeps flashing.
Switch off the developer options on the Android
device.
Reconnect the Android device.
If this does not solve the problem, the connected
Android device does not support the Auto Mode.
The iPod/iPhone does not turn on or does not
work.
Check the connection.
Update the firmware version.
Charge the battery.
Reset the iPod/iPhone.
Sound is distorted.
Deactivate the equalizer either on this unit or the
iPod/iPhone.
A lot of noise is generated.
Turn off (uncheck) “VoiceOver” on the iPod/ iPhone.
For details, visit .
No operations are available when playing back a
track containing artwork.
Operate the unit after the artwork has loaded.
“Authorization Error” appears.
Check whether the connected iPod/iPhone is
compatible with this unit. (Page 49)
Tuner
SSM automatic presetting does not work.
Store stations manually. (Page 18)
Static noise while listening to the radio.
Connect the antenna firmly.
ENGLISH
00_KW-V2018ST_M_ENG.indb 51
51
17/6/2017 7:35:55 AM
Troubleshooting
AV-IN
No picture appears on the screen.
Turn on the video component if it is not on.
Connect the video component correctly.
Spotify
The application does not work.
The application on your iPod touch/iPhone/
Android is not the latest version. Update the
application.
Pandora*/Spotify
The application does not work.
The application on your iPod touch/iPhone/
Android is not the latest version. Update the
application.
“Please update Pandora App” appears.
The Pandora application on your iPod touch/
iPhone/Android is not the latest version. Update
the application.
“Please check device.” appears.
The Pandora application on your iPod touch/
iPhone/Android has not started up.
The Pandora application is not installed on the
connected device.
An error has occurred on the Pandora application.
“Login Error” appears.
You have not been signed into Pandora.
“No skips remaining” appears.
No more songs can be skipped.
52
“Failed to save your thumb rating” appears.
Thumb-up/down is prohibited.
“No Station” appears.
No station is available.
“No Active Station” appears.
No station is being played.
“Station limit reached” appears.
The station list is full and no more stations can be
registered.
“Failed to save your bookmark” appears.
The unit has failed to save a bookmark. Try the
operation again.
“Limited Connectivity” appears.
The connection with the Pandora application
cannot be established.
“Pandora not available” appears.
You cannot use the Pandora application from
the area where you are currently trying to access
Pandora.
“Try again later” appears.
The Pandora server is under maintenance.
“Station does not exist” appears.
The selected station has been deleted by another
device or has expired.
“Cannot create a Station” appears.
You cannot create a station during the readonly mode or when network connection is not
established.
* Only for KW-V340BT Region 4.
Bluetooth
Phone sound quality is poor.
Reduce the distance between the unit and the
Bluetooth mobile phone.
Move the car to a place where you can get a better
signal reception.
The sound is interrupted or skipped while using a
Bluetooth audio player.
Reduce the distance between the unit and the
Bluetooth audio player. Disconnect the device
connected for Bluetooth phone.
Turn off, then turn on the unit.
(When the sound is not yet restored) connect the
player again.
The connected audio player cannot be controlled.
Check whether the connected audio player
supports AVRCP (Audio/Video Remote Control
Profile).
The Bluetooth device does not detect the unit.
Search from the Bluetooth device again.
The unit does not pair with the Bluetooth device.
For devices compatible with Bluetooth 2.1:
Register the device using a PIN code. (Page 31)
For devices compatible with Bluetooth 2.0:
Enter the same PIN code for both the unit and
target device. If the PIN code of the device is not
indicated in its instructions, try “0000” or “1234.”
Turn off, then turn on the Bluetooth device.
Echo or noise occurs.
Adjust the microphone unit position.
Adjust the echo volume or noise reduction volume.
(Page 28)
ENGLISH
00_KW-V2018ST_M_ENG.indb 52
17/6/2017 7:35:55 AM
Troubleshooting
The unit does not respond when you try to copy
the phone book to the unit.
You may have tried to copy the same entries (as
stored) to the unit.
Specifications
Monitor section
Picture Size (W × H)
KW-V340BT/KW-V340BTM:
6.2 inches (diagonal) wide
137.5 mm × 77.2 mm
D/A Converter
24 bit
Audio Decoder
Linear PCM/Dolby Audio/
MP3/WMA/WAV/AAC (.m4a)
KW-V440BT/KW-V440BTM:
6.75 inches (diagonal) wide
151.8 mm × 79.68 mm
Video Decoder
DivX/MPEG1/MPEG2/JPEG
Wow & Flutter
Below Measurable Limit
Frequency Response
96 kHz Sampling:
20 Hz to 22 000 Hz
48 kHz Sampling:
20 Hz to 22 000 Hz
44.1 kHz Sampling:
20 Hz to 20 000 Hz
Total Harmonic
Distortion
0.010% (1 kHz)
Signal to Noise Ratio
99 dB (DVD-Video 96 kHz)
Dynamic Range
99 dB (DVD-Video 96 kHz)
USB 2.0 Full Speed/High
Speed
Disc Format
DVD-Video/VIDEO-CD/CD-DA
Sampling Frequency
44.1 kHz/48 kHz/96 kHz
Compatible Device
Mass Storage Class
16 bit/20 bit/24 bit
File System
FAT 16/32
Quantifying Bit
Number
Maximum Power
Supply Current
DC 5 V
“Connection Error” appears.
The device is registered but the connection has
failed. Connect the registered device. (Page 27)
“Please Wait...” appears.
The unit is preparing to use the Bluetooth function.
If the message does not disappear, turn off and
turn on the unit, then connect the device again (or
reset the unit).
“No Voice Device” appears.
The connected mobile phone does not have a
voice recognition system.
“No Data” appears.
No phone book data is contained in the connected
Bluetooth phone.
“Initialize Error” appears.
The unit has failed to initialize the Bluetooth
module. Try the operation again.
“Dial Error” appears.
Dialing has failed. Try the operation again.
DVD player section
Display System
Transparent TN LCD panel
Drive System
TFT active matrix system
Number of Pixels
1 152 000
(800H × 480V × RGB)
Effective Pixels
99.99%
Pixel Arrangement
RGB striped arrangement
Back Lighting
LED
USB interface section
USB Standard
1.5 A
“Hung Up Error” appears.
The call has not ended yet. Park your car, and use
the connected mobile phone to end the call.
D/A Converter
24 bit
Audio Decoder
“Pick Up Error” appears.
The unit has failed to receive a call.
MP3/WMA/AAC (.aac/.m4a)/
WAV/FLAC
Video Decoder
DivX/MPEG1/MPEG2/JPEG
ENGLISH
00_KW-V2018ST_M_ENG.indb 53
53
17/6/2017 7:35:55 AM
Specifications
FM tuner section
Bluetooth section
HPF (High Pass Filter)
Frequency (Hz):
Through/30/40/50/60/70/
80/90/100/120/150/180/
220/250
Slope (dB/Oct.):
–6/–12/–18/–24
Gain (dB):
–8/–7/–6/–5/–4/–3/–2/–1/0
LPF (Low Pass Filter)
Frequency (Hz):
30/40/50/60/70/80/90/100/
120/150/180/220/250/
Through
Slope (dB/Oct.):
–6/–12/–18/–24
Gain (dB):
–8/–7/–6/–5/–4/–3/–2/–1/0
Frequency Range
87.5 MHz to 108.0 MHz
(50 kHz)
Technology
Bluetooth 3.0
Frequency
2.402 GHz to 2.480 GHz
Usable Sensitivity
(S/N: 30 dB, 22.5 kHz)
6.2 dBf (0.56 μV/75 Ω)
Output Power
+4 dBm (MAX), 0 dBm (AVE),
Power Class 2
Quieting Sensitivity
(S/N: 46 dB, 22.5 kHz)
15.2 dBf (1.58 μV/75 Ω)
Line of sight approx. 10 m
Frequency Response
(±3.0 dB)
30 Hz to 15 kHz
Maximum
Communication
Range
Audio Codec
SBC/AAC
Profile
HFP (Hands Free Profile) 1.6
A2DP (Advanced Audio
Distribution Profile) 1.3
AVRCP (Audio/Video Remote
Control Profile) 1.5
GAP (Generic Access Profile)
PBAP (PhoneBook Access
Profile) 1.2
SDP (Service Discovery Profile)
SPP (Serial Port Profile) 1.2
Color System of
External Video Input
NTSC/PAL
1 Vp-p/75 Ω
Equalizer
13 Band
External Video Input
Level (RCA jack)/
(mini jack)
Band
Frequency (Hz) (BAND1 – 13):
62.5/100/160/250/400/630/
1k/1.6k/2.5k/4k/6.3k/10k/
16k
Level:
−09 to +09 (−9 dB to +9 dB)
Q: 1.35/1.5/2.0
Video Output Level
(RCA jack)
1 Vp-p/75 Ω
Analog RGB Input
KW-V340BT Region 3/
KW-V340BTM Region 2/
KW-V440BT Region 3 (except
for Indonesian models)/
KW-V440BTM Region 2:
0.7 Vp-p/75 Ω
Signal to Noise Ratio
68 dB (MONO)
Selectivity (±400 kHz)
> 80 dB
Stereo Separation
40 dB (1 kHz)
AM tuner section
Frequency Range
KW-V340BT Region 3/
KW-V440BT Region3:
531 kHz to 1 611 kHz (9 kHz)
KW-V340BTM Region 2/
KW-V440BTM Region 2:
531 kHz to 1 602 kHz (9 kHz)
KW-V340BT Region 4:
531 kHz to 1 701 kHz (9 kHz)
Usable Sensitivity
54
28.5 dBμ
DSP section
Video section
ENGLISH
00_KW-V2018ST_M_ENG.indb 54
17/6/2017 7:35:55 AM
Specifications
Audio section
Maximum Power
(Front & Rear)
50 W × 4
Full Bandwidth
Power (Front & Rear)
22 W × 4
(at less than 1% THD)
Preout Level
4 V/10 kΩ
Preout Impedance
≤ 600 Ω
Speaker Impedance
4 Ω to 8 Ω
General
Operating Voltage
14.4 V
(10.5 V to 16 V allowable)
Maximum Current
Consumption
10 A
Installation Size
(Main Unit)
(W × H × D)
178 mm × 100 mm × 162 mm
Operational
Temperature Range
–10°C to +60°C
Weight (Main Unit)
1.7 kg
Design and specifications are subject to change
without notice.
ENGLISH
00_KW-V2018ST_M_ENG.indb 55
55
17/6/2017 7:35:55 AM
Specifications
Trademarks and licenses
• Dolby, Dolby Audio and the double-D symbol are
trademarks of Dolby Laboratories.
• “DVD Logo” is a trademark of DVD Format/Logo
Licensing Corporation registered in the US, Japan
and other countries.
• The “AAC” logo is a trademark of Dolby Laboratories.
• Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation in
the United States and/or other countries.
• “Made for iPod,” and “Made for iPhone” mean that an
electronic accessory has been designed to connect
specifically to iPod, or iPhone, respectively, and
has been certified by the developer to meet Apple
performance standards.
Apple is not responsible for the operation of this
device or its compliance with safety and regulatory
standards. Please note that the use of this accessory
with iPod, or iPhone may affect wireless performance.
iPhone, iPod, iPod classic, iPod nano, and iPod touch
are trademarks of Apple Inc., registered in the U.S.
and other countries.
• Lightning is a trademark of Apple Inc.
• This item incorporates copy protection technology
that is protected by U.S. patents and other
intellectual property rights of Rovi Corporation.
Reverse engineering and disassembly are prohibited.
• Font for this product is designed by Ricoh.
• Android is a trademark of Google Inc.
• The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any
use of such marks by JVC KENWOOD Corporation is
under license. Other trademarks and trade names are
those of their respective owners.
56
ENGLISH
00_KW-V2018ST_M_ENG.indb 56
• THIS PRODUCT IS LICENSED UNDER THE AVC PATENT
PORTFOLIO LICENSE FOR THE PERSONAL USE OF A
CONSUMER OR OTHER USES IN WHICH IT DOES NOT
RECEIVE REMUNERATION TO
(i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC
STANDARD ("AVC VIDEO") AND/OR (ii) DECODE
AVC VIDEO THAT WAS ENCODED BY A CONSUMER
ENGAGED IN A PERSONAL ACTIVITY AND/OR WAS
OBTAINED FROM A VIDEO PROVIDER LICENSED TO
PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR
SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL
INFORMATION MAY BE OBTAINED FROM MPEG LA,
L.L.C. SEE HTTP://WWW.MPEGLA.COM
• SPOTIFY and the Spotify logo are among the
registered trademarks of Spotify AB.
• Pandora, the Pandora logo, and the Pandora trade
dress are trademarks or registered trademarks of
Pandora Media, Inc., used with permission.
• libFLAC
Copyright (C) 2000-2009 Josh Coalson
Copyright (C) 2011-2013 Xiph.Org Foundation
Redistribution and use in source and binary forms,
with or without modification, are permitted provided
that the following conditions are met:
– Redistributions of source code must retain the
above copyright notice, this list of conditions
and the following disclaimer.
– Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and
the following disclaimer in the documentation and/
or other materials provided with the distribution.
– Neither the name of the Xiph.org Foundation
nor the names of its contributors may be used
to endorse or promote products derived from
this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE FOUNDATION OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT
OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGE.
• DIVX
– This DivX Certified® device can play DivX® Home
Theater video files up to 576p (including .avi, .divx).
Download free software at www.divx.com to
create, play and stream digital video.
– DivX®, DivX Certified® and associated logos are
trademarks of DivX, LLC and are used under license.
17/6/2017 7:35:55 AM
00_KW-V2018ST_M_ENG.indb 57
17/6/2017 7:35:55 AM
For updated information (the latest Instruction Manual, system updates, new functions, etc.),
please visit the following website:
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.6
Linearized : Yes
Encryption : Standard V2.3 (128-bit)
User Access : Print, Extract, Print high-res
Create Date : 2017:06:17 07:37:05+08:00
Modify Date : 2017:09:12 14:43:14+08:00
Has XFA : No
XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Creator Tool : Adobe InDesign CS5.5 (7.5)
Metadata Date : 2017:09:12 14:43:14+08:00
Format : application/pdf
Title : KW_V340BT_M
Creator :
Producer : Acrobat Distiller 10.0.0 (Windows)
Document ID : uuid:58dea6f8-12b2-498d-b350-df1fb762c5cf
Instance ID : uuid:201b6967-a9d2-4e7b-86ad-119e8c2fad20
Page Layout : SinglePage
Page Count : 60
EXIF Metadata provided by EXIF.tools
.