JVC KW V340BTM KW_V340BT_M User Manual V340BTM, V440BTM B5A 2150 00

KW-V440BT KW-V440BT, KW-V440BTM B5A_2150_00 English, (Instruction manual) Asia

KW-V340BT KW-V340BT, KW-V340BTM, KW-V440BT, KW-V440BTM B5A_2150_00 English, (Instruction manual) Asia

KW-V340BT, KW-V340BTM KW-V340BT, KW-V340BTM (Instruction manual) Asia B5A_2150_00

User Manual: JVC KW-V340BTM KW-V340BTM, KW-V440BTM English, (Instruction manual) Asia

Open the PDF directly: View PDF .
Page Count: 60

KW-V340BT (Region 3 – DVD Region Code 3 Area)

KW-V340BT (Region 4 – DVD Region Code 4 Area)

KW-V340BTM (Region 2 – DVD Region Code 2 Area)

KW-V440BT (Region 3 – DVD Region Code 3 Area)

KW-V440BTM (Region 2 – DVD Region Code 2 Area)

MONITOR WITH DVD RECEIVER

INSTRUCTION MANUAL

This instruction manual is used to describe models listed above. Model availability and features (functions)

may differ depending on the country and sales area. B5A-2150-00 (M/M2/X/A9)

ENGLISH

00_KW-V2018ST_M_ENG.indb 100_KW-V2018ST_M_ENG.indb 1 17/6/2017 7:35:42 AM17/6/2017 7:35:42 AM

ENGLISHi

Important NoticeImportant Notice

To ensure proper use, please read through this

manual before using this product. It is especially

important that you read and observe WARNINGS

and CAUTIONS in this manual.

Please keep the manual in a safe and accessible

place for future reference.

WARNINGS

To prevent accidents and damages

• DO NOT install any unit or wire any cable in a

location where;

–it may obstruct the steering wheel and gearshift

lever operations.

–it may obstruct the operation of safety devices such

as air bags.

–it may obstruct visibility.

• DO NOT raise the volume level too much, as this will

make driving dangerous by blocking outside sounds,

and may cause hearing loss.

• DO NOT operate the unit while driving. If you need

to operate the unit while driving, be sure to look

around carefully.

• Stop the car before performing any complicated

operations.

• The driver must not watch the monitor while driving.

CAUTIONS

To care for the unit

• If you have parked the car for a long time in hot or

cold weather, wait until the temperature in the car

becomes normal before operating the unit.

To care for the monitor

• The monitor built into this unit has been produced

with high precision, but it may have some ineffective

dots. This is inevitable and is not considered

defective.

• Do not expose the monitor to direct sunlight.

• Do not operate the touch panel using a ball-point

pen or similar tool with a sharp tip.

Touch the keys on the touch panel with your finger

directly (if you are wearing a glove, take it off).

• When the temperature is very cold or very hot...

–Chemical changes occur inside, causing

malfunction.

–Pictures may not appear clearly or may move

slowly. Pictures may not be synchronized with

the sound or picture quality may decline in such

environments.

On the volume setting

• Digital devices produce very little noise compared

with other sources. Lower the volume before playing

these digital sources to avoid damaging the speakers

by sudden increase of the output level.

The marking of products using lasers

The label is attached to the chassis/case and says

that the component uses laser beams that have been

classified as Class 1. It means that the unit is utilizing

laser beams that are of a weaker class. There is no

danger of hazardous radiation outside the unit.

00_KW-V2018ST_M_ENG.indb i00_KW-V2018ST_M_ENG.indb i 17/6/2017 7:35:43 AM17/6/2017 7:35:43 AM

ENGLISH ii

Important NoticeImportant Notice

For KW-V340BTM Region 2/KW-V440BTM Region 2:

For Turkey

Bu ürün 28300 sayılı Resmi Gazete’de yayımlanan Atik

Elektrikli ve Elektronik Eşyalarin Kontrolü Yönetmeliğe

uygun olarak üretilmiştir.

Eski Elektrik ve Elektronik Ekipmanların İmha

Edilmesi Hakkında Bilgi (ayrı atık toplama

sistemlerini kullanan ülkeleri için uygulanabilir)

Sembollü (üzerinde çarpı işareti olan çöp

kutusu) ürünler ev atıkları olarak atılamaz.

Eski elektrik ve elektronik ekipmanlar,

bu ürünleri ve ürün atıklarını

geri dönüştürebilecek bir tesiste

değerlendirilmelidir. Yaşadığınız bölgeye

en yakın geri dönüşüm tesisinin yerini

öğrenmek için yerel makamlara müracaat

edin. Uygun geri dönüşüm ve atık

imha yöntemi sağlığımız ve çevremiz

üzerindeki zararlı etkileri önlerken

kaynakların korunmasına da yardımcı

olacaktır.

For KW-V340BTM Region 2/KW-V440BTM Region 2:

Declaration of Conformity with regard to the RE

Directive 2014/53/EU

Declaration of Conformity with regard to the RoHS

Directive 2011/65/EU

Manufacturer:

JVC KENWOOD Corporation

3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi,

Kanagawa, 221-0022, Japan

EU Representative:

JVCKENWOOD Deutschland GmbH

Konrad-Adenauer-Allee 1-11, 61118 Bad Vilbel,

GERMANY

English

Hereby, JVCKENWOOD declares that the radio

equipment “KW-V340BTM/KW-V440BTM” is in

compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is

available at the following internet address:

http://www.jvc.net/cs/car/eudoc/

RE 2014/53/EU Direktifi uyarınca Uygunluk Beyanı

RoHS Yönergesi 2011/65/EU’ya göre Uygunluk

Bildirimi

Üretici:

JVC KENWOOD Corporation

3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi,

Kanagawa, 221-0022, Japan

AB Temsilcisi:

JVCKENWOOD Deutschland GmbH

Konrad-Adenauer-Allee 1-11, 61118 Bad Vilbel,

GERMANY

Turkish

Burada, JVCKENWOOD “KW-V340BTM/KW-V440BTM”

radyo ekipmanının 2014/53/AB Direktifine uygun

olduğunu bildirir.

AB uyumluluk deklarasyonunun tam metni aşağıdaki

internet adresinde mevcuttur.

http://www.jvc.net/cs/car/eudoc/

00_KW-V2018ST_M_ENG.indb ii00_KW-V2018ST_M_ENG.indb ii 17/6/2017 7:35:43 AM17/6/2017 7:35:43 AM

About this manual

The displays and panels shown in this manual are

examples used to provide clear explanations of the

operations. For this reason, they may be different

from the actual displays or panels.

Illustrations of KW-V440BT are mainly used for

explanation.

The region code of a particular model will only

be stated if only one of the regions supports the

particular feature with the same model name.

This manual mainly explains operations using the

buttons on the monitor panel and keys on the

touch panel. For operations using the remote

controller, see page 41.

< > indicates the various screens/menus/

operations/settings that appear on the touch

panel.

[ ] indicates the keys on the touch panel.

Indication language: English indications are used

for the purpose of explanation. You can select the

indication language from the <Settings> menu.

(Page 38)

ContentsContents

Component Names and Operations .............. 3

Basic Operations ................................................ 3

How to reset your unit ................................................... 3

Turning on the power .................................................... 3

Turning off the power .................................................... 3

Turning off the AV source ............................................ 4

Turning off the screen .................................................... 4

Adjusting the volume .................................................... 4

Attenuating the sound ............................................... 4

Getting Started .................................................. 4

Initial settings....................................................................... 4

Clock settings ...................................................................... 5

Various Screens and Operations .................... 6

Home screen ........................................................................ 6

Source control screen .................................................... 7

List/setting screen ............................................................ 9

Disc ..................................................................... 10

Video .................................................................. 11

USB ..................................................................... 13

Android.............................................................. 15

iPod/iPhone ...................................................... 16

Tuner .................................................................. 17

Pandora® ........................................................... 20

Spotify ............................................................... 22

Other External Components ......................... 24

AV-IN ...................................................................................... 24

Rear view camera ........................................................... 24

TV tuner box ...................................................................... 25

External navigation unit ............................................. 25

Bluetooth® ........................................................ 26

Information ........................................................................ 26

Preparation ......................................................................... 26

Connection ........................................................................ 26

Bluetooth mobile phone ........................................... 28

Bluetooth audio player ............................................... 30

JVC Streaming DJ ....................................................... 30

Bluetooth settings ......................................................... 31

Settings ............................................................. 31

Audio settings .................................................................. 31

Display settings ............................................................... 34

Input settings.................................................................... 37

System settings ............................................................... 38

Remote Controller ........................................... 41

Preparation ......................................................................... 41

Basic operations .............................................................. 42

Searching for an item directly ................................ 42

JVC Remote APP .......................................................... 42

Installation and Connection .......................... 43

Before installation .......................................................... 43

Installing the unit ........................................................... 44

Installing the trim plate .............................................. 44

Wiring connection ......................................................... 45

Connecting external components ...................... 46

References ........................................................ 46

Maintenance ..................................................................... 46

More information ........................................................... 46

Troubleshooting .............................................. 50

Specifications ................................................... 53

Trademarks and licenses ........................................... 56

2ENGLISH

00_KW-V2018ST_M_ENG.indb 200_KW-V2018ST_M_ENG.indb 2 17/6/2017 7:35:43 AM17/6/2017 7:35:43 AM

Component Names and Operations Component Names and Operations

KW-V440BT/KW-V440BTM

1 Volume +/– buttons

2 Loading slot

3 FNC button

• (Press) Turns on the power.

• (Press) Pops up the short-cut menu while the

power is on.

• (Hold): Activates the voice dialing.

4 Reset button

5 Monitor panel

6 Screen (touch panel)

To display the Home screen

KW-V340BT/KW-V340BTM

1 button

• (Press) Turns on the power.

• (Hold) Turns off the power.

• (Press) Pops up the short-cut menu while the

power is on.

2 Reset button

3 Loading slot

4 HOME/ button

• HOME (Press): Displays the Home screen.

• (Hold): Activates the voice dialing.

5 button

• (Press) Displays the current source control screen.

For KW-V340BT Region3, KW-V340BTM

Region2, pressing switches the screen

between the current source control screen and

navigation screen. For details, see page 38.

• (Hold) Turns off/on the screen.

6 Volume +/– buttons

7 Monitor panel

8 Screen (touch panel)

Basic Operations Basic Operations

How to reset your unit

If the unit fails to operate properly, press the reset

button.

KW-V340BT/KW-V340BTM

KW-V440BT/KW-V440BTM

Turning on the power

KW-V340BT/

KW-V340BTM

KW-V440BT/

KW-V440BTM

Turning off the power

(Hold)

KW-V340BT/KW-V340BTM

ENGLISH

00_KW-V2018ST_M_ENG.indb 300_KW-V2018ST_M_ENG.indb 3 17/6/2017 7:35:43 AM17/6/2017 7:35:43 AM

Initial settings

When you power on the unit for the first time or reset

the unit, the <Initial Settings> screen appears.

Perform the initial settings.

E.g. Initial settings screen for KW-V440BT

Once completed, Home screen appears.

For KW-V440BT Region 3, Indonesian models, a

caution message will appear.

Touch [OK] to confirm the caution message.

• The caution message appears each time you turn on

the unit.

Getting Started Getting Started

KW-V440BT/KW-V440BTM

On the Home screen, touch as follows:

Turning off the AV source

1 Display the source/option selection

screen.

On the Home screen, touch as follows:

2 Turn off the AV source.

On the source/option selection screen, touch as

follows:

Turning off the screen

KW-V340BT/KW-V340BTM

(Hold)

• The button illumination also lights off when you turn

off the screen.

To turn on the screen: Press and hold on the

monitor panel or touch the screen.

Basic OperationsBasic Operations

• For KW-V440BT/KW-V440BTM: See “Using the

pop-up short-cut menu” on page 8.

Adjusting the volume

KW-V340BT/

KW-V340BTM

KW-V440BT/

KW-V440BTM

You can adjust the volume (00 to 35) by pressing + to

increase and pressing – to decrease.

• Holding + increases the volume continuously to

level 15.

Attenuating the sound

On the source control screen, touch as follows:

[ ] becomes blue.

To cancel attenuation: Touch [ ] again. ([ ]

becomes white.)

4ENGLISH

00_KW-V2018ST_M_ENG.indb 400_KW-V2018ST_M_ENG.indb 4 17/6/2017 7:35:44 AM17/6/2017 7:35:44 AM

Getting StartedGetting Started

*1 For KW-V440BT Region 3, Indonesian models, <OFF> is

selected initially.

*2 For KW-V440BT Region 3, Indonesian models, <Bahasa

Indonesia> is selected initially.

Clock settings

1 Display the Home screen.

KW-V340BT/

KW-V340BTM

KW-V440BT/

KW-V440BTM

2 Display the <Clock> screen.

On the Home screen, touch as follows:

Then, on the <Settings> screen, touch as follows:

[System]  <Clock> : [Enter]

• You can also display the <Clock> screen by

touching the clock area on the Home screen.

• ON (Initial)*1: Activates the display demonstration.

• OFF: Deactivates the display demonstration.

Select the text language used for on-screen

information.

• English (Initial)*2/Español/Français/Deutsch/

Italiano/Nederlands/Ελληνικά/Português/Türkçe/

Čeština/Polski/Magyar/Руccĸий/ / /

/ / / /Bahasa

Malaysia/Bahasa Indonesia/

–For external monitors, only English/Spanish/

French/German/Italian/Dutch/Russian/Portuguese

are available. If another language has been

selected, the text language for external monitors

will be set to English.

• GUI Language (Local (the language selected

above)/English (Initial)*2): Selects the language used

for displaying operation keys and menu items.

“Please Power Off” appears when the setting is

changed. Turn off the power, then turn on to enable

the change.

<Rear Camera> (Page 37)

Make the settings to display the picture from the

connected rear view camera.

<User Customize> (Page 35)

Change the display design.

Select the viewing angle in relation to the monitor

panel to make the panel easier to see.

• Under 0° (Initial)/5°/10°/15°/20°

3 Set the clock time.

E.g. Clock settings screen for KW-V440BT

• Radio Data System: Synchronizes the clock time

with FM Radio Data System.

• Off: Sets the clock manually. Touch [J]/[K] to

adjust the hour, then minute.

–Touching [Reset] will set the minute to “00”.

ENGLISH

00_KW-V2018ST_M_ENG.indb 500_KW-V2018ST_M_ENG.indb 5 17/6/2017 7:35:44 AM17/6/2017 7:35:44 AM

Various Screens and Operations Various Screens and Operations

KW-V440BT/KW-V440BTM

• You can change the icon design. For details, see

page 36.

Touching the operation keys performs the following

actions:

1 Displays the <Settings> screen.

2 Ejects the disc.

3 Displays the <Clock> screen.

4 Displays the <User Customize> screen.

5 Displays all playback sources and options.

6 Selects or changes the playback source.

7 Displays the phone control screen.

Available playback sources and options

Touch 5 to display the source/option selection screen.

E.g. Source/option selection screen for KW-V440BT

Touching the operation keys performs the following

actions:

[Tuner] Switches to the radio broadcast.

[Disc] Plays a disc.

[USB] Plays files on a USB device.

[iPod] Plays an iPod/iPhone.

[Android™] Plays an Android device.

[BT Audio] Plays a Bluetooth audio player.

[AV-IN] Switches to an external component

connected to the AV-IN input

terminal.

[Spotify] Switches to the Spotify application.

[Pandora]*1 Switches to the Pandora Broadcast.

[Navi]*2 Displays the navigation screen.

[Phone] Displays the phone control screen.

[AV Off] Turns off the AV source.

[Home]*3 Displays the Home screen.

[Setup]*3 Displays the <Setting> screen.

[Power Off]*3 Turns off the power.

[Camera] Switches to the camera connected

to the rear view camera input.

[Now Playing]*3 Displays the source currently

played back.

*1 Only for KW-V340BT Region 4.

*2 Only for KW-V340BT Region 3, KW-V340BTM Region 2,

KW-V440BT Region 3 (except for Indonesian models),

KW-V440BTM Region 2. Selectable only when a navigation unit

is connected.

*3 Only for KW-V440BT/KW-V440BTM.

You can display or change to other screens at any time

to show information, change the AV source, change

the settings, etc.

Home screen

When you turn on the power for the first time, the

Home screen appears.

• You can customize the Home screen. (Pages 7

and 35)

• To display the Home screen from other screens:

For KW-V340BT/KW-V340BTM: Press HOME on the

monitor panel.

For KW-V440BT/KW-V440BTM: Press FNC on the

monitor panel, then touch [Home] on the pop-up

short-cut menu.

KW-V340BT/KW-V340BTM

• You can change Home screen design (icons and

layout). For details, see page 35.

6ENGLISH

03_KW_V340BT_M_Body01.indd 603_KW_V340BT_M_Body01.indd 6 18/7/2017 9:49:24 AM18/7/2017 9:49:24 AM

Various Screens and OperationsVarious Screens and Operations

Source control screen

You can perform the playback operation from the

source control screen during playback.

• The operation keys and information displayed vary

depending on the selected source/disc type/file type

being played.

• If the operation keys are not displayed on the screen,

touch the screen to show them.

E.g. Common audio playback source screen:

KW-V340BT/KW-V340BTM

KW-V440BT/KW-V440BTM

1 Playing time/playback status

2 Playback source or media type

3 Current playback item information

(folder no./file no./track no./total track no./playback

file type)

4 [M]: Ejects the disc.

[ ]: Attenuates/restores the sound.

5 Clock display

6 Only for KW-V340BT/KW-V340BTM: Playback

source items shown on the Home screen.

• Touching the playback source item changes the

playback source.

7 Displays/hides other available operation keys*

8 Operation keys*

9 IN indicator (lights up while a disc is inserted)

p Track/file/song/video information

• Touching [H] scrolls the text if not all of the text

is shown.

q Playback mode indicator (Repeat/Random)

w File type indicator

e Picture/artwork (shown if the file contains the

information)

* See “Common operation keys on source control screen” on

page8.

To return to the Home screen

Touch [ ] or [Home] on the source/option

selection screen.

Customizing the Home screen

1 Select an item to replace.

On the Home screen, touch and hold the icon you

want to replace.

The item selection screen is displayed.

2 Select an item (1) you want to display in

the selected position, then touch [ ]

(2).

Repeat the procedure to customize your Home

screen.

E.g. Home item selection screen for KW-V440BT

• Only selectable sources are shown.

• You cannot locate [Camera] on the Home

screen.

ENGLISH

03_KW_V340BT_M_Body01.indd 703_KW_V340BT_M_Body01.indd 7 18/7/2017 9:55:35 AM18/7/2017 9:55:35 AM

Various Screens and OperationsVarious Screens and Operations

Using gesture control

You can also control playback by moving your finger

on the touch panel as follows (for some sources, the

gesture control is not available).

• Sliding the finger up/down:

Selects a folder.

• Sliding the finger left/right:

Selects an item (chapter/track/audio file/video file).

• Moving your finger clockwise/counterclockwise:

Increases/decreases the volume.

Using the pop-up short-cut menu

While displaying the source control screen, you can

jump to another screen by touching the operation

keys on the pop-up short-cut menu.

1 Display the pop-up short-cut menu.

KW-V340BT/

KW-V340BTM

KW-V440BT/

KW-V440BTM

[FNC J]For KW-V340BT/KW-V340BTM:

Displays the pop-up short-cut menu.

• To close the menu, touch [K].

[ ] For KW-V440BT/KW-V440BTM:

Displays the Home screen.

[ ] Displays the folder list/track list/audio

menu/video menu.

[S]/[T]• (Touch) Selects an item (chapter/

folder/track/audio file/video file).

• (Hold) Reverses/forwards search.

• (Hold) Plays in slow-motion while

paused for video playback.

[IW]Starts/pauses playback.

[ ] Selects random playback mode.*

* About playback mode:

–Available playback mode differs depending on the source, disc

type, connected device, etc.

–You cannot activate repeat playback mode and random

playback mode at the same time.

–To cancel the playback mode, touch repeatedly until the

indicator disappears.

Common operation keys on source control screen

• The following explanations state the operation keys

for KW-V440BT, unless stated otherwise.

• The appearance of the operation keys may differ,

however the similar operation keys have the same

operations.

• Available operation keys differ depends on the

selected source or connected device.

Touching the operation keys performs the following

actions:

[ ] Displays other available operation keys

besides those shown on 8.

• To hide the window, touch [ ] .

[ ][ ] Selects a folder.

[ ] Selects repeat playback mode.*

[o]Stops playback.

[MODE] Displays the setting screen of the current

playback source.

8ENGLISH

00_KW-V2018ST_M_ENG.indb 800_KW-V2018ST_M_ENG.indb 8 17/6/2017 7:35:45 AM17/6/2017 7:35:45 AM

2 Select an item to jump to by touching as

follows.

For KW-V340BT/KW-V340BTM:

[ ] Displays the phone control screen.

[ ] Activates the voice dialing.

[ ] Displays the <Equalizer> screen.

[ ] Displays the picture adjustment screen.

[ ] Displays the <User Customize> screen.

For KW-V440BT/KW-V440BTM:

[ ] (Touch) Switches the screen.

(Hold) Turns off the screen.

[ ] Displays the phone control screen.

[ ] Activates the voice dialing.

[ ] Displays the picture from the connected

rear view camera.

[ ] Displays the picture adjustment screen.

[ ] Displays the <Equalizer> screen.

[ ] Displays the Home screen.

[ ] Displays all playback sources and items.

• The playback source buttons/items displayed on

the Home screen are displayed on the pop-up

short-cut menu. Touching these operation keys

changes the playback source.

Various Screens and OperationsVarious Screens and Operations

To close the pop-up menu

• KW-V340BT/KW-V340BTM: Touch [K] or touch the

screen anywhere other than the pop-up short-cut

menu.

• KW-V440BT/KW-V440BTM: Press FNC on the

monitor panel.

Using touch screen operation during

playback

Touching the areas performs the following actions:

1 Displays the video control menu while playing a

video.

2 While playing a video: Displays the source control

screen.

While playing an audio file: Displays the playback

operation keys.

3 Goes to the previous chapter/track.*

4 Goes to the next chapter/track.*

* Not available for video from an external component (AV-IN).

List/setting screen

Below are the common operation keys which appear

on the list/setting screen..

• The appearance of the operation keys may differ,

however the similar operation keys have the same

operations.

• Available operation keys differ depends on the

setting screens. Not all these operation keys are

shown on every screen.

Touching the operation keys performs the following

actions:

1 Enters alphabet search* to list the items in

alphabetical order. When a keypad appears, touch

the first letter you want to search for.

2 Returns to the root folder.

3 Returns to the upper layer.

4 Closes the current screen.

5 Exits from the current screen or returns to the

previous screen.

6 Changes the page to display more items.

* Alphabet search is not available when the playlist is selected.

9ENGLISH

00_KW-V2018ST_M_ENG.indb 900_KW-V2018ST_M_ENG.indb 9 17/6/2017 7:35:45 AM17/6/2017 7:35:45 AM

Disc Disc

Selecting a folder/track on the list

1 Display the folder/track list.

On the source control screen, touch as follows:

2 Select the folder (1), then the item (2) in

the selected folder.

Select an item in each layer until you reach and

select the desired file.

Settings for disc playback

• Available items shown on the <DISC Mode> screen

differ depending on the type of disc/file being

played back.

1 Display the <DISC Mode> screen.

On the source control screen, touch as follows:

Ejecting a disc

On the Home screen or source control screen, touch

as follows:

• When removing a disc, pull it out horizontally.

• You can eject a disc while playing another AV source.

• If the ejected disc is not removed within 15 seconds,

the disc is automatically inserted again into the

loading slot to protect it from dust.

Playback operations

Audio playback information and key

operation

• For playback information, see “Source control screen”

on page7.

• For key operations on the touch panel, see “Common

operation keys on source control screen” on

page8.

• If a disc does not have a disc menu, all tracks on it will

be played repeatedly until you change the source or

eject the disc.

• For playable disc types, file types and other

information, see pages46 and 47.

• If “ ” appears on the screen, the unit cannot accept

the operation you have tried to do.

–In some cases, without showing “ ”, operations

will not be accepted.

• When playing back a multi-channel encoded disc,

the multi-channel signals are downmixed.

Inserting a disc

Label side up

E.g. Inserting a disc for KW-V440BT

The source changes to “DISC” and playback starts.

• The IN indicator lights up while a disc is inserted.

10 ENGLISH

00_KW-V2018ST_M_ENG.indb 1000_KW-V2018ST_M_ENG.indb 10 17/6/2017 7:35:45 AM17/6/2017 7:35:45 AM

DiscDisc

2 Make the settings.

<Menu language>*1

Select the initial disc menu language. (Initial:

English)

<Subtitle language>*1

Select the initial subtitle language or turn subtitles

off (Off). (Initial: English)

<Audio language>*1

Select the initial audio language. (Initial: English)

You can change the dynamic range while playing

Dolby Audio encoded discs.

• Wide: Reproduces powerful sound at a low

volume level with its full dynamic range.

• Normal: Reduces the dynamic range a little.

• Dialog (Initial): Reproduces movie dialog more

clearly.

When playing back a multi-channel disc, this

setting affects the signals reproduced through the

front and/or rear speakers.

• Dolby Surround: Reproduces multi-channel

surround sound by connecting an amplifier

compatible with Dolby Surround.

• Stereo (Initial): Reproduces stereo playback

sound.

Select the monitor type to watch a wide screen

picture on the external monitor.

16:9 (Initial) 4:3 LB 4:3 PS

<File Type>*2

Select the playback file type when a disc contains

different types of files.

• Audio: Plays back audio files.

• Still image: Plays back still picture files.

• Video: Plays back video files.

• Audio&Video (Initial): Plays back audio files and

video files.

*1 For list of language codes, see page48.

*2 For playable file types, see page46.

If the disc contains no files of the selected type, the existing

files are played in the following priority: audio, video, then still

picture. You can change these settings only while playback is

stopped.

Video Video

Playback operations

Video playback information on the source

control screen

E.g. Video playback source control screen for

KW-V440BT

1 Media type

2 Playback status

3 Current playback item information

(title no./chapter no./folder no./file no./track no.)

4 Playing time

5 IN indicator (lights up while a disc is inserted)

6 Playback mode indicator (Repeat/Random)

7 File type indicator

ENGLISH

00_KW-V2018ST_M_ENG.indb 1100_KW-V2018ST_M_ENG.indb 11 17/6/2017 7:35:46 AM17/6/2017 7:35:46 AM

VideoVideo

Touching the operation keys performs the following

actions:

[ ]*1 Displays the picture size selection

screen.

1 Touch [ Zoom] to change the

magnification level of the picture

(Zoom1, Zoom2, Zoom3, Full:

Initial).

2 Touch [J] [K] [H] [I] to move the

zooming frame.

[ ] Displays the aspect ratio selection

screen.

Touch [ Aspect] to select the aspect

ratio.

<Full>*2: For 16:9 original pictures

4:3 signal 16:9 signal

<Just>: For viewing 4:3 pictures

naturally on the wide screen

4:3 signal 16:9 signal

<Normal>*2: For 4:3 original pictures

4:3 signal 16:9 signal

<Auto>: For “DISC” source and

“USB” source only: The aspect ratio is

automatically selected to match the

incoming signals.

[ ] Displays the picture adjustment screen.

1 Touch [DIM ON] or [DIM OFF] to

turn on or off the dimmer.

2 Touch [+]/[–] to adjust the other

items.

• <Bright>: Adjusts the brightness

(−15 to +15).

• <Contrast>: Adjusts the contrast

(−10 to +10).

• <Black>: Adjusts the blackness

(−10 to +10).

• <Color>: Adjusts the color

(−10 to +10).

• <Tint>: Adjusts the tint (−10 to +10).

• <Sharpness>: Adjusts the sharpness

(−2 to +2).

[ ] Selects the audio type.

[ ] Selects the subtitle type.

[ ] Selects the view angle.

*1 When [ ] is set to <Just> or <Auto>, the picture is

zoomed with the aspect ratio of the <Full> setting.

This feature may not be used for some video sources.

*2 While DivX is played back with <Screen Ratio> set to [16:9]

(Page11 for discs/Page14 for USB), the aspect ratio may

not be set correctly.

Video menu control operations

You can display the video menu control during video

playback.

• Available operation keys differ depend on the

selected disc type and file type.

Video playback except VCD

E.g. Video menu control screen for KW-V440BT

12 ENGLISH

00_KW-V2018ST_M_ENG.indb 1200_KW-V2018ST_M_ENG.indb 12 17/6/2017 7:35:46 AM17/6/2017 7:35:46 AM

[ MENU] Displays the disc menu (DVD).

[T MENU] Displays the disc menu (DVD).

[ ] Switches to the direct disc menu mode.

Touch the target item to select.

[ ] Displays the menu/scene selection

screen.

• [J] [K] [H] [I]: Selects an item.

• [Enter]: Confirms the selection.

• [Return]: Returns to the previous

screen.

Video playback for VCD

E.g. Video menu control screen for KW-V440BT

VideoVideo USB USB

You can connect a USB mass storage class device such

as a USB memory, digital audio player, etc. to the unit.

• For playable file types and other information, see

pages46 and49.

• You cannot connect a PC or portable HDD to the

USB input terminal.

• You cannot connect a USB device via a USB hub.

Connecting a USB device

On the rear panel

USB device (commercially available)

The source changes to “USB” and playback starts.

• All tracks in the USB device will be played repeatedly

until you change the source or disconnect the USB

device.

Touching the operation keys performs the following

actions:

[ ]

Refer to “Video playback except VCD” on

page12.

[ ]

[ MENU] Displays the disc menu.

[ ] Selects the audio channel

(ST: stereo, L: left, R: right).

[ ] *Displays or hides the direct selection

buttons.

1 Touch [DIR/CLR] to select a track

directly on a VCD.

2 Touch the numbers ([0], [1] to [9]) to

select the desired track.

3 Touch [Enter] to confirm.

To delete the last entry, touch [DIR/

CLR].

[Return] Displays the previous screen or menu.

* You need to stop playback to deactivate the PBC function when

playing a VCD with PBC activated.

13ENGLISH

00_KW-V2018ST_M_ENG.indb 1300_KW-V2018ST_M_ENG.indb 13 17/6/2017 7:35:46 AM17/6/2017 7:35:46 AM

USBUSB

Selecting a folder/track on the list

1 Display the folder/track list.

On the source control screen, touch as follows:

2 Select the folder (1), then the item (2) in

the selected folder.

Select an item in each layer until you reach and

select the desired file.

Settings for USB playback

1 Display the <USB Mode> screen.

On the source control screen, touch as follows:

2 Make the settings.

Select the monitor type to watch a wide screen

picture on the external monitor.

16:9 (Initial) 4:3 LB 4:3 PS

• Next: Switch between internal memory and the

memory source of the connected device (such as

a mobile phone).

Playback operations

Playback information and key operation

• For playback information, see “Source control screen”

on page7.

• For key operations on the touch panel, see “Common

operation keys on source control screen” on

page8.

Selecting the file type to play

You can specify the file type to play.

E.g. USB source control screen for KW-V440BT

Select the file type as follows:

[Audio] Plays back audio files.

[Video] Plays back video files.

[Photo] Plays back still picture files.

If the USB contains no files of the selected type, the

existing files are played in the following priority: audio,

video, then still picture. You can change these settings

only while playback is stopped.

14 ENGLISH

00_KW-V2018ST_M_ENG.indb 1400_KW-V2018ST_M_ENG.indb 14 17/6/2017 7:35:46 AM17/6/2017 7:35:46 AM

Android Android

This unit supports the Android™ application, JVC

Music Play. When you use JVC Music Play via this unit,

you can search for audio files by genre, artist, album,

playlist and song.

• For more information about JVC Music Play, visit

<http://www.jvc.net/cs/car/>.

Preparation

Installing JVC Music Play

Install the Android™ application, JVC Music Play, on

your Android device beforehand.

• When a compatible Android device is connected,

“Press [VIEW] to install JVC MUSIC PLAY APP” is shown

on the Android device. Follow the instructions to

install the application.

• You can also install the latest version of JVC Music

Play on your Android device before connecting.

Connecting an Android device

This unit supports Android OS 4.1 and above.

• Some Android devices (with OS 4.1 and above) may

not fully support Android Open Accessory (AOA) 2.0.

• If the Android device supports both mass storage

class device and AOA 2.0, this unit always plays back

via AOA 2.0 as priority.

Android (commercially available)

On the rear panel

USB cable (commercially available)

Start playback

1 Turn on JVC Music Play on your Android

device.

2 Select “Android” as the source.

Playback operations

Playback information and key operation

• For playback information, see “Source control screen”

on page7.

• For key operations on the touch panel, see “Common

operation keys on source control screen” on

page8.

Selecting a track from the menu

1 Display the audio menu.

On the source control screen, touch as follows:

2 Select a category (1), then select a

desired item (2).

Select an item in each layer until you reach and

select the desired file.

ENGLISH

00_KW-V2018ST_M_ENG.indb 1500_KW-V2018ST_M_ENG.indb 15 17/6/2017 7:35:47 AM17/6/2017 7:35:47 AM

iPod/iPhone iPod/iPhone

Connecting an iPod/iPhone

• For playable iPod/iPhone types and other

information, see page 49.

• You cannot watch video.

Wired connection

iPod/iPhone

Lightning model

(commercially available)

iPod/iPhone 30-pin

connector model

(commercially available)

On the rear panel

USB Audio cable

for iPod/iPhone:

KS-U62 (optional

accessory)

30-pin to USB cable

(accessory of iPod/

iPhone)

Bluetooth connection

Pair the iPod/iPhone with this unit via Bluetooth.

(Page26)

Selecting the playback device via the

connection method

See <Smartphone Setup> on page 38 for more

information.

Playback operations

Playback information and key operation

• For playback information, see “Source control screen”

on page7.

• For key operations on the touch panel, see “Common

operation keys on source control screen” on

page8.

Additional keys operations. Touching the operation

keys performs the following actions:

[ ] Switches the device on <Smartphone

Setup> screen. (Page38)

Selecting an audio file from the menu

1 Display the audio menu.

On the source control screen, touch as follows:

Settings for Android playback

1 Display the <Android MODE> screen.

On the source control screen, touch as follows:

2 Make the settings.

• ON (Initial): Shows the artworks of the playing

files.

• OFF: Hides the artworks of the playing files.

• AUTO MODE (Initial): Controls from the unit

(using the JVC Music Play application).

• AUDIO MODE: Controls other media player

applications from the Android device (without

using the JVC Music Play application).

–You can play/pause or skip files from the unit.

AndroidAndroid

16 ENGLISH

00_KW-V2018ST_M_ENG.indb 1600_KW-V2018ST_M_ENG.indb 16 17/6/2017 7:35:47 AM17/6/2017 7:35:47 AM

iPod/iPhoneiPod/iPhone

2 Select a category (1), then select a

desired item (2).

Select an item in each layer until you reach and

select the desired file.

• Available categories differ depending on the type

of iPod/iPhone.

Settings for iPod/iPhone playback

1 Display the <iPod Mode> screen.

On the source control screen, touch as follows:

2 Make the settings.

• ON (Initial): Shows the artworks of the playing

files.

• OFF: Hides the artworks of the playing files.

Listening to the radio

Playback information on the source control

screen

KW-V340BT/KW-V340BTM

KW-V440BT/KW-V440BTM

Tuner Tuner

1 Displays/hides other available operation keys*

2 Current station frequency

3 Text information

• Touching [ ] scrolls the text if not all of the text

is shown.

• Touching [Radio Text] switches the information

between Radio Text, Radio Text Plus and PTY

code.

4 Displays the preset stations window (Page19)

5 [P1] – [P5]

• (Touch) Selects a preset station.

• (Hold) Presets the current station.

6 NEWS indicator

7 AF indicator

8 TI indicator

9 Operation keys*

p ST/MONO indicator

The ST indicator lights up when receiving an FM

stereo broadcast with sufficient signal strength.

q Seek mode indicator

w LO.S indicator

e RDS indicator

r EON indicator

The EON indicator lights up when a Radio Data

System station is sending EON signals.

t Selects the band (AM/FM1/FM2/FM3)

y Only for KW-V340BT/KW-V340BTM: Playback

source items shown on the Home screen.

• Touching the playback source item changes the

playback source.

* See “Operation keys on source control screen” on page18.

17ENGLISH

00_KW-V2018ST_M_ENG.indb 1700_KW-V2018ST_M_ENG.indb 17 17/6/2017 7:35:47 AM17/6/2017 7:35:47 AM

Operation keys on source control screen

• The following explanations state the operation keys

for KW-V440BT, unless stated otherwise.

• The appearance of the operation keys may differ,

however the similar operation keys have the same

operations.

• See also “Common operation keys on source control

screen” on page8.

Touching the operation keys performs the following

actions:

[SSM ]*1 (Hold) Presets stations automatically.

[MONO]*1 Activates monaural mode for better FM

reception (stereo effect will be lost).

• The MONO indicator lights up while

monaural mode is activated.

• To deactivate, touch [MONO] again.

[TI]*1 (For FM RDS features)

Activates TI standby reception mode.

• When TI is activated, the unit is ready

to switch to traffic information if

available. The TI indicator lights up in

white.

• If the TI indicator lights up in orange,

tune into another station providing

Radio Data System signals.

• The volume adjustment for Traffic

Information is automatically

memorized. The next time the unit

switches to Traffic Information, the

volume is set to the memorized level.

• To deactivate, touch [TI] again.

TunerTuner

Presetting stations in the memory

You can preset five stations for each band.

Automatic presetting — SSM (Strong-

station Sequential Memory) (for FM only)

On the source control screen, touch as follows:

(Hold)

The local stations with the strongest signals are found

and stored automatically.

Manual presetting

1 Tune in to a station you want to preset.

2 Select a preset number to store into.

(Hold)

E.g. Tuner source control screen for KW-V440BT

The station selected in step 1 is stored into the

preset number [P1] to [P5] you have selected.

[MODE ]*1 Change the settings for the selected

tuner reception on <Tuner Mode>

screen. (Page 19)

[PTY]*1*2 (For FM RDS features)

Enters PTY search mode.

1 Touch [PTY].

2 Touch and hold a PTY code to search

for.

If there is a station broadcasting a

program of the same PTY code as you

have selected, that station is tuned in.

[SEEK] Changes the seek mode for [S]/[T].

• AUTO1 (Initial): Auto search

• AUTO2: Tunes in preset stations one

after another

• MANU: Manual search

[S]/[T]Searches for a station.

• The search method differs according

to the selected seek mode (see above).

*1 Appears only when FM is selected as the source.

*2 Only English/Spanish/French/German/Dutch/ Portuguese are

available for the text language here. If another language has

been selected in <Language> (Page 38), the text language

is set to English.

18 ENGLISH

00_KW-V2018ST_M_ENG.indb 1800_KW-V2018ST_M_ENG.indb 18 17/6/2017 7:35:47 AM17/6/2017 7:35:47 AM

Selecting a preset station

1 Select the band, then display the preset

station window.

On the source control screen, touch as follows:

2 Select a preset station.

E.g. Preset station window for KW-V440BT

To hide the window: Touch [ ] or [ ].

Settings for other FM Radio Data System

features

1 Display the <Tuner Mode> screen.

On the source control screen, touch as follows:

TunerTuner

2 Make the settings.

When driving in an area where FM reception is not

sufficient enough, this unit automatically tunes in

to another FM Radio Data System station of the

same network, possibly broadcasting the same

program with stronger signals— Network-Tracking

Reception.

Select the Network-Tracking Reception mode.

• AF: Switches to another station. The program

may differ from the one currently received. The

AF indicator lights up.

• AF Reg: Switches to another station broadcasting

the same program. The AF indicator lights up.

• OFF (Initial): Deactivates the function.

The RDS indicator lights up when the Network-

Tracking Reception is activated and an FM Radio

Data System station is found.

<NEWS>*

• 00min to 90min: Activates New Standby

Reception by selecting the period of time to

disable the interruption. The NEWS indicator

lights up.

• OFF (Initial): Deactivates the function.

<Local>

• ON: Tunes in only to FM stations with sufficient

signal strength. The LO.S indicator lights up.

• OFF (Initial): Deactivates the function.

• ON (Initial): Automatically searches for a station

with better reception for traffic information if the

current reception of current station is poor.

• OFF: Deactivates the function.

* The volume adjustment for Traffic Information is automatically

memorized. The next time the unit switches to Traffic

Information, the volume is set to the previous level.

19ENGLISH

00_KW-V2018ST_M_ENG.indb 1900_KW-V2018ST_M_ENG.indb 19 17/6/2017 7:35:47 AM17/6/2017 7:35:47 AM

Pandora® Pandora® (Only for KW-V340BT Region 4)

You can stream Pandora from iPhone/iPod touch or

Android devices.

• Pandora is only available in certain countries. For

more information, visit <www.pandora.com/legal>.

• Because Pandora is a third-party service, the

specifications are subject to change without

prior notice. Accordingly, compatibility may be

impaired or some or all of the services may become

unavailable.

• Some functions of Pandora cannot be operated from

this unit.

• For issues using the application, contact Pandora at

<pandora-support@pandora.com>.

Preparation

Installing the application

Your smartphone must has built in Bluetooth and the

following profiles must be supported:

• SPP (Serial Port Profile)

• A2DP (Advanced Audio Distribution Profile)

Establish an Internet connection using LTE, 3G, EDGE,

or WiFi.

Ensure you are logged in to your smartphone

application. If you do not have a Pandora account, you

can create one for free from your smartphone or at

<www.pandora.com>.

Install the latest version of the Pandora application on

your smartphone.

• For Android devices: Search for “Pandora” in Google

play to find and install the most recent version.

• For iPhone/iPod touch: Search for “Pandora” in the

Apple iTunes App Store to find and install the most

recent version.

Connecting the device

For Android devices

Pair the Android device with this unit via Bluetooth.

(Page 26)

For iPhone/iPod touch

• Via USB input terminal: Connect iPhone/iPod touch

with the cable. (Page 16)

–For Lightning models: Use KS-U62 (optional

accessory).

–For 30-pin connector models: Use 30-pin to USB

cable (accessory of iPod/iPhone).

• Via Bluetooth: Pair the iPhone/iPod touch with this

unit. (Page 26)

Selecting the device

For selecting the playback device via the connection

method to use, see <Smartphone Setup> on page

38.

Playback operations

Playback information and key operation

You can also operate Pandora with optional remote

controller, RM-RK258.

You can only control play, pause and skip with the

remote controller.

1 Playing time/playback status

2 Track information

• Touching [H] scrolls the text if not all of the text

is shown.

3 Picture data

4 Playback source items shown on the Home screen.

• Touching the playback source item changes the

playback source.

5 Displays/hides other available operation keys*

6 Operation keys*

* See “Operation keys on source control screen” on page 21.

20 ENGLISH

00_KW-V2018ST_M_ENG.indb 2000_KW-V2018ST_M_ENG.indb 20 17/6/2017 7:35:48 AM17/6/2017 7:35:48 AM

Pandora®Pandora®

Operation keys on source control screen

• The appearance of the operation keys may differ,

however the similar operation keys have the same

operations.

• See also “Common operation keys on source control

screen” on page8.

Touching the operation keys performs the following

actions:

[ ] Adds the current artist to the station list.

[ ] Adds the current track to the station list.

[ ] Bookmarks the current track.

[ ] Switches the device on <Smartphone

Setup> screen. (Page 38)

[ ] Displays the list selection screen.

[ ] Thumbs down to the current track and

skips to the next track.

[ ] Registers the current track as a favorite.

[ I/W ] Starts/pauses playback.

[ T ]Skips the current track.

• Not available when the Pandora skip

reaches its limit.

Selecting a station from the list

1 Display the list selection screen.

On the source control screen, touch as follows:

2 Select the list type.

Station List Genre List

Pandora

[Station List] Selects from the station names.

[Genre List] Selects from the genres.

3 Select a station from the list.

On the station list

Shuffle By Date

By Name

Station Name

Pandora

• To play all the songs in the registered stations

randomly, touch [Shuffle].

• To sort the list in reverse chronological order,

touch [By Date].

• To sort the list in alphabetical order, touch [By

Name].

• The indicator appears on the right of the

item when the station is shared.

On the genre list

Genre Name 1 Song Name 1

Genre Name 2 Song Name 2

Genre Name 3 Song Name 3

Genre Name 4 Song Name 4

Genre Name 5 Song Name 5

Pandora

1 Select a genre.

2 Select a station.

The selected station is added to the station list.

ENGLISH

00_KW-V2018ST_M_ENG.indb 2100_KW-V2018ST_M_ENG.indb 21 17/6/2017 7:35:48 AM17/6/2017 7:35:48 AM

Spotify Spotify

Playback operations

Playback information and key operation

KW-V340BT/KW-V340BTM

KW-V440BT/KW-V440BTM

You can also operate Spotify with a remote controller

(supplied/optionally purchased), RM-RK258.

You can only control play, pause and skip with the

remote controller.

With Spotify, your music is everywhere. Working out,

partying or relaxing, the right music is always at your

fingertips. There are millions of songs on Spotify—from

old favorites to the latest hits. Just choose the music

you love, or let Spotify surprise you.

You can stream Spotify from iPhone/iPod touch or

Android devices.

• Because Spotify is a third-party service, the

specifications are subject to change without

prior notice. Accordingly, compatibility may be

impaired or some or all of the services may become

unavailable.

• Some functions of Spotify cannot be operated from

this unit.

• For issues using the application, contact Spotify at

<www.spotify.com>.

Preparation

Installing the application

Your smartphone must has built in Bluetooth and the

following profiles must be supported:

• SPP (Serial Port Profile)

• A2DP (Advanced Audio Distribution Profile)

Establish an Internet connection using LTE, 3G, EDGE,

or WiFi.

Ensure you are logged in to your smartphone

application. If you do not have an Spotify account, you

can create one for free from your smartphone or at

<www.spotify.com>.

Install the latest version of the Spotify application on

your smartphone.

• For Android devices: Search for “Spotify” in Google

play to find and install the most recent version.

• For iPhone/iPod touch: Search for “Spotify” in the

Apple iTunes App Store to find and install the most

recent version.

Connecting the device

For Android devices

Pair the Android device with this unit via Bluetooth.

(Page 26)

For iPhone/iPod touch

• Via USB input terminal: Connect iPhone/iPod touch

with the cable. (Page16)

–For Lightning models: Use KS-U62 (optional

accessory).

–For 30-pin connector models: Use 30-pin to USB

cable (accessory of iPod/iPhone).

• Via Bluetooth: Pair the iPhone/iPod touch with this

unit. (Page26)

Selecting the device

For selecting the playback device via the connection

method to use, see <Smartphone Setup> on page

38.

22 ENGLISH

00_KW-V2018ST_M_ENG.indb 2200_KW-V2018ST_M_ENG.indb 22 17/6/2017 7:35:48 AM17/6/2017 7:35:48 AM

SpotifySpotify

1 Playing time/playback status

2 Track information

• Touching [H] scrolls the text if not all of the text

is shown.

• Touching [ ]/[ ] changes the displayed

information between artist ( ) and album ( ).

3 Picture data

4 Only for KW-V340BT/KW-V340BTM: Playback

source items shown on the Home screen.

• Touching the playback source item changes the

playback source.

5 Displays/hides other available operation keys*

6 Progress bar

7 Operation keys*

* See “Operation keys on source control screen” below.

Operation keys on source control screen

• The following explanations state the operation keys

for KW-V440BT, unless stated otherwise.

• The appearance of the operation keys may differ,

however the similar operation keys have the same

operations.

• See also “Common operation keys on source control

screen” on page8.

Touching the operation keys performs the following

actions:

[ ]*1 Thumbs down to the current track and

skips to the next track.

[ ]*1 Registers the current track as a favorite.

[ ] *2*3 Activates/deactivates shuffle playback

mode.

[ ] *2 Repeats all tracks/cancels the repeat

playback.

[ ] *2*3 Repeats the current track/cancels the

repeat playback.

[ ] Creates a new station.

[ ] Switches the device on <Smartphone

Setup> screen. (Page38)

[ ] Displays the Spotify menu screen.

[ ]*3[ ] Selects a track.

[ ][ ] Starts (I)/pauses (W) playback.

[ ]Saves the current track/artist to <Your

Music>.

*1 Not available for tracks in a playlist.

*2 Not available for tracks in the Radio.

*3 Available only for premium account users.

Creating your station (Start Radio)

Start Radio is to start a radio channel based on the

currently played track.

Create your station.

On the source control screen, touch as follows:

Station is created and playback starts automatically.

• You can personalize your station using thumb up

([ ]) or thumb down ([ ]).

–You cannot thumb up or down while playing tracks

in a playlist.

–Personalizing stations may not be available

depending on the track.

ENGLISH

00_KW-V2018ST_M_ENG.indb 2300_KW-V2018ST_M_ENG.indb 23 17/6/2017 7:35:48 AM17/6/2017 7:35:48 AM

SpotifySpotify Other External Components Other External Components

AV-IN

Connecting an external component

See page 46 for more information.

Starting playback

1 Select “AV-IN” as the source.

2 Turn on the connected component and

start playing the source.

Changing the AV-IN name

You can change the AV-IN name displayed on the

source control screen.

• This setting does not affect the source name

displayed on the Home screen.

1 Display the <VIDEO Mode> screen.

On the source control screen, touch as follows:

2 Select an AV-IN name

Rear view camera

Install the rear view camera (separately purchased) in

the appropriate position according to the instructions

supplied with the rear view camera.

Connecting a rear view camera

See page 46 for more information.

• To use the rear view camera, a reverse lead (REVERSE)

connection is required. (Page 45)

Using the rear view camera

• For rear camera settings, see <Rear Camera> on

page 37.

To display the rear view camera screen

The rear view screen is displayed by shifting the gear

to the reverse (R) position when <Rear Camera

Interruption> is set to [ON]. (Page37)

• A caution message appears on the screen. To

remove the caution message, touch the screen.

You can also display the picture from the rear view

camera manually without shifting the gear to the

reverse (R) position.

On the Home screen, touch as follows:

Selecting a track

1 Display the Spotify menu screen.

On the source control screen, touch as follows:

2 Select the list type, then select a desired

item.

The list types displayed differ depending on the

information sent from Spotify.

• To return to the top layer, touch [ ].

• To return to the upper layer, touch [ ] .

24 ENGLISH

00_KW-V2018ST_M_ENG.indb 2400_KW-V2018ST_M_ENG.indb 24 17/6/2017 7:35:49 AM17/6/2017 7:35:49 AM

Other External ComponentsOther External Components

Operations while the camera screen is

displayed

To adjust the picture

Touch the area shown below.

Video menu control screen is displayed. For details, see

“Video menu control operations” on page12.

• To exit video menu control screen, touch the same

area again.

To display parking guide line

Set <Parking Guidelines> to [ON] (Page37) or

touch the area shown below.

• To close the parking guidelines, touch the same area

again.

To exit the camera screen

Touch the area shown below or perform the following

to display the Home screen:

• For KW-V340BT/KW-V340BTM: Press HOME on the

monitor panel.

• For KW-V440BT/KW-V440BTM: Press FNC on the

monitor panel, then touch [Home] on the pop-up

short-cut menu.

TV tuner box

(Only for KW-V440BT Region 3 (except for

Indonesian models), KW-V440BTM Region 2)

You can connect a TV tuner box (commercially

available) to the REMO OUT output terminal to watch

TV.

Connecting a TV tuner box

See page 46 for more information.

Displaying the TV screen

• For settings, see <TV Tuner Control> on page 38.

1 Select “AV-IN” as the source.

2 Turn on the TV tuner box.

To change the channels: Touch [ CH J ] or [ CH K ].

External navigation unit

(Only for KW-V340BT Region 3, KW-V340BTM

Region 2, KW-V440BT Region 3 (except for

Indonesian models), KW-V440BTM Region 2)

You can connect an external navigation unit

(commercially available) to the NAV input terminal so

that you can view the navigation screen. (Page 46)

• The navigation guidance comes out of the front

speakers even when you are listening to an audio

source.

Viewing the navigation screen

• For settings, see <Navigation> on page 37.

Select “Navi” as the source.

On the Home screen, touch as follows:

• While the navigation screen is displayed, the touch

panel operations are available only for navigation.

• The aspect ratio of the navigation screen is fixed

to <FULL> regardless of the [ ] setting.

(Page12).

To exit the navigation screen

For KW-V340BT Region 3, KW-V340BTM Region 2:

Press on the monitor panel.

For KW-V440BT Region 3 (except for Indonesian

models), KW-V440BTM Region 2: Touch [ ] on the

pop-up short-cut menu.

ENGLISH

03_KW_V340BT_M_Body01.indd 2503_KW_V340BT_M_Body01.indd 25 5/7/2017 4:03:21 PM5/7/2017 4:03:21 PM

Bluetooth® Bluetooth®

Connection

When you connect a Bluetooth device to the unit for

the first time:

1 Register the device by pairing the unit and the

device.

2 Connect the device to the unit. (Page27)

Registering a new Bluetooth device

Pairing allows Bluetooth devices to communicate with

each other.

• The pairing method differs depending on the

Bluetooth version of the device.

–For devices with Bluetooth 2.1:

You can pair the device and the unit using SSP

(Secure Simple Pairing) which only requires

confirmation.

–For devices with Bluetooth 2.0:

You need to enter a PIN code both on the device

and unit for pairing.

• Once the connection is established, it is registered in

the unit even if you reset the unit. Up to five devices

can be registered in total.

• Two devices for Bluetooth phone and one for

Bluetooth audio can be connected at a time.

However, when “BT Audio” is selected as the source,

you can connect up to five Bluetooth audio devices

and switch between these five devices.

• To use the Bluetooth function, you need to turn on

the Bluetooth function of the device.

Information

Bluetooth is a short-range wireless radio

communication technology for mobile devices such as

mobile phones, portable PCs and other devices.

Bluetooth devices can be connected without cables

and communicate with each other.

Note

• While driving, do not perform complicated

operations such as dialing numbers, using the phone

book, etc. When you perform these operations, stop

your car in a safe place.

• Some Bluetooth devices may not connect to this unit

depending on the Bluetooth version of the device.

• This unit may not work for some Bluetooth devices.

• Connecting conditions may vary depending on your

environment.

• For some Bluetooth devices, the device is

disconnected when the unit is turned off.

• If your mobile phone supports PBAP (Phone Book

Access Profile), you can display the following items

on the touch panel when the mobile phone is

connected.

–Phone book

–Dialed calls, received calls, and missed calls (up to

10 entries in total)

Preparation

Connect and install the microphone beforehand. For

details, see page 45.

Auto pairing

When <Auto Pairing> is set to [ON], Android or iOS

(such as iPhone) devices are automatically paired

when connected via USB. (Page31)

Pairing a Bluetooth device using SSP (for

Bluetooth 2.1)

When the Bluetooth device is compatible with

Bluetooth 2.1, a pairing request is sent from the

available device.

1 Search for the unit (“JVC KW-V”) from your

Bluetooth device.

2 Confirm the request both on the device

and the unit.

On the device:

On the unit:

To reject the request: Touch [Cancel].

26 ENGLISH

00_KW-V2018ST_M_ENG.indb 2600_KW-V2018ST_M_ENG.indb 26 17/6/2017 7:35:49 AM17/6/2017 7:35:49 AM

Bluetooth®Bluetooth®

Pairing a Bluetooth device using a PIN code (for

Bluetooth 2.0)

1 Display the <PIN Code Set> screen.

On the Home screen, touch as follows:

Then, on the <Settings> screen, touch as follows:

[System]  <Bluetooth Setup> : [Enter]

On the <Bluetooth Setup> screen, touch as

follows:

<PIN Code> : [0000]

2 Change the PIN code.

If you wish to skip changing the PIN code, go to

step 3.

• To delete the last entry, touch [Clear].

• To delete the PIN code, touch and hold [Clear].

3 Search for the unit (“JVC KW-V”) from your

Bluetooth device.

4 Select the unit (“JVC KW-V”) on your

Bluetooth device.

• If a PIN code is required, enter “0000” (initial) or

new PIN code you have entered in step 2.

• When pairing is completed, the device is

registered on the <Paired Device List> screen.

Note

• The PIN code is initially set to “0000”.

• The maximum number of digits in the PIN code is 15.

Connecting/disconnecting a registered

Bluetooth device

1 Display the <Paired Device List> screen.

On the Home screen, touch as follows:

Then, on the <Settings> screen, touch as follows:

[System]  <Bluetooth Setup> : [Enter]

On the <Bluetooth Setup> screen, touch as

follows:

<Paired Device List> : [Enter]

2 Select the device (1) you want to connect,

then select [Connection] (2).

3 Select the device (1) to connect, then

return to the <Paired Device List> (2).

Select [ON] (to connect) or [OFF] (to disconnect).

: Mobile phone

: Audio device

4 Connect the selected device.

27ENGLISH

00_KW-V2018ST_M_ENG.indb 2700_KW-V2018ST_M_ENG.indb 27 17/6/2017 7:35:49 AM17/6/2017 7:35:49 AM

Bluetooth®Bluetooth®

• The status is shown as follows:

–<Connecting>: Connection is in progress.

–<Connected>: A connection has been established.

–<Connect Ready>: A connection can be

established.

–<Disconnecting>: Disconnection is in progress.

–<Disconnected>: No connection is established.

• When a Bluetooth mobile phone is connected, the

signal strength and battery level are displayed when

the information is acquired from the device.

To delete the registered device: Perform step 1,

select the device you want to delete in step 2, then

touch [Remove].

• A confirmation message appears. Touch [Yes].

Bluetooth mobile phone

When a call comes in...

Touching the operation keys performs the following

actions:

[ ] Answers a call.

[ ] Rejects a call.

• Call information is displayed if acquired.

• Phone operation is not available while the picture

from the rear view camera is displayed.

• For KW-V340BT Region 3, KW-V340BTM Region

2, KW-V440BT Region 3 (except for Indonesian

models), KW-V440BTM Region 2: When receiving

a call during navigation guidance, the screen is

switched automatically.

– To return to the navigation screen, touch [ ] .

During a call...

Touching the operation keys performs the following

actions:

[ ] Ends a call.

[ ] /

[ ]

Switches between handsfree mode and

phone mode.

[DTMF] Enters DTMF (Dual Tone Multi

Frequency), then sends text using the

keypad.

NR LEVEL

[–] / [+]

Adjusts the noise reduction level.

(–5 to 5, initial 0)

EC LEVEL

[–] / [+]

Adjusts the echo volume level.

(–5 to 5, initial 0)

MIC LEVEL

[–] / [+]

Adjusts the volume level of the

microphone. (–10 to 10, initial –4)

• Press + / – buttons on the monitor panel to adjust

the volume of the call or earpiece.

Making a call

1 Display the phone control screen.

On the Home screen, touch [Phone]. (See also

page 6.)

2 Select a method to make a call.

1 From the call history* (missed calls/received

calls/dialed calls)

2 From the phone book*

3 From the preset list (Page29)

4 Use direct number entry

5 Use voice dialling

* Applicable only for mobile phone compatible with PBAP (Phone

Book Access Profile).

3 Select a contact (1), then make a call (2).

When item 1, 2 or 3 is selected in step 2:

28 ENGLISH

00_KW-V2018ST_M_ENG.indb 2800_KW-V2018ST_M_ENG.indb 28 17/6/2017 7:35:50 AM17/6/2017 7:35:50 AM

Bluetooth®Bluetooth®

To use alphabet search in the phone book

1 Touch [ A-Z].

2 Touch the first letter you want to search for on

the keypad.

To search for a number, touch [1,2,3...].

3 Select a contact you want call from the list.

To display other phone numbers in the same

contact

You can store up to 10 phone numbers per

contact.

1 Touch [ ].

2 Select a contact you want call from the list.

When item 4 is selected in step 2:

Enter the phone number (1), then make a

call (2).

• To enter “+”, touch and hold [0/+].

• To delete the last entry, touch [ ].

When item 5 is selected in step 2:

Say the name of the person you want to

call.

• Available only when the connected mobile

phone has a voice recognition system.

• If the unit cannot find the target, “Please speak

into the microphone” appears. Touch [Start],

then say the name again.

• To cancel voice dialling, touch [Cancel].

Switching between two connected devices

You can change the device to use when 2 devices are

connected.

On the phone control screen:

The active device is highlighted.

Presetting phone numbers

You can preset up to five phone numbers.

1 Display the phone control screen.

On the Home screen, touch [Phone]. (See also

page 6.)

2 Select call history or phone book calling

method (1), then select a contact (2) to

preset.

3 Select a preset number to store into.

(Hold)

To delete the contact in the preset number: Touch

[ ] besides the contact on the preset list.

ENGLISH

00_KW-V2018ST_M_ENG.indb 2900_KW-V2018ST_M_ENG.indb 29 17/6/2017 7:35:50 AM17/6/2017 7:35:50 AM

Bluetooth®Bluetooth®

KW-V440BT/KW-V440BTM

1 Tag data* (current track title/artist name/album

title)

• Pressing [H] scrolls the text if not all of the text is

shown.

2 Connected device name

• Touching the device name switches to another

connected Bluetooth audio device.

3 Signal strength and battery level

(Appear only when the information is acquired

from the device.)

4 Playing time*/playback status*

* Available only for devices compatible with AVRCP 1.3.

Playback information and key operation

• For playback information, see “Source control screen”

on page7.

• For key operations on the touch panel, see “Common

operation keys on source control screen” on

page8.

Bluetooth audio player

JVC Streaming DJ

When “BT Audio” is selected as the source, you can

connect up to five Bluetooth audio devices at the

same time. You can easily switch between these five

devices by playing music from the device.

KW-V340BT/KW-V340BTM

Additional keys operations. Touching the operation

keys performs the following actions:

[ ] Displays <Bluetooth Setup> screen.

Selecting an audio file from the menu

1 Display the audio menu.

On the source control screen, touch as follows:

2 Select a category (1), then select a

desired item (2).

Select an item in each layer until you reach and

select the desired file.

30 ENGLISH

03_KW_V340BT_M_Body01.indd 3003_KW_V340BT_M_Body01.indd 30 18/7/2017 10:04:53 AM18/7/2017 10:04:53 AM

Bluetooth®Bluetooth®

Bluetooth settings

You can change various settings for using Bluetooth

devices on the <Bluetooth Setup> screen.

1 Display the <Bluetooth Setup> screen.

On the Home screen, touch as follows:

Then, on the <Settings> screen, touch as follows:

[System]  <Bluetooth Setup> : [Enter]

2 Make the settings.

Display the list of registered devices. You can

connect a device or delete registered devices.

Change the PIN code of the unit.

Show the device name of this unit to be shown on

the Bluetooth device — JVC KW-V.

Show the device address of the unit.

• ON (Initial): Automatically establishes a

connection with the last connected Bluetooth

device when the unit is turned on.

• OFF: Cancels.

Select the speakers used for Bluetooth mobile

phones and Bluetooth audio players.

• Front Only: Front speakers only.

• All (Initial): All speakers.

• ON: The unit answers the incoming calls

automatically in 5 seconds.

• OFF (Initial): The unit does not answer the calls

automatically. Answer the calls manually.

• ON (Initial): Establishes pairing automatically

with the Android or iOS device (such as iPhone)

connected via USB. (Auto pairing may not work

for some devices depending on the Android/iOS

version.)

• OFF: Cancels.

Touch and hold [Enter] to reset all settings you

have made for using Bluetooth mobile phones and

Bluetooth audio players.

Settings Settings

Audio settings

Display the <Audio> screen.

On the Home screen, touch as follows:

Then, on the <Settings> screen, touch [Audio].

E.g. Audio settings screen for KW-V440BT

You cannot change the <Audio> screen in the

following situations:

• When the AV source is turned off.

• When the Bluetooth phone is used (making or

receiving a call, during a call, or while voice dialling).

• During navigation guidance.

The following adjustments are memorized for each

source until you adjust the sound again. If the source

is a disc, the adjustments are stored for each of the

following categories.

• DVD/VCD

• CD

• DivX/MPEG1/MPEG2/MP3/WMA/WAV/AAC/FLAC

You cannot adjust the sound when the unit is in

standby.

ENGLISH

03_KW_V340BT_M_Body01.indd 3103_KW_V340BT_M_Body01.indd 31 5/7/2017 4:04:10 PM5/7/2017 4:04:10 PM

Settings Settings

Selecting a preset sound mode

Select a preset sound mode on the <Equalizer>

screen.

• Flat (Initial)/Hard Rock/Pop/Hip Hop/R&B/Jazz/

Classical/drvn 3/drvn 2/drvn 1/User

• To apply the adjusted equalizer to all playback

sources, touch [ALL SRC], then touch [OK] to

confirm.

Store your own sound adjustments

1 Select a preset sound mode.

2 Select a band (1) and adjust the level (2),

then adjust the sound (3).

Adjust the sound as follows:

Adjusts the width of the frequency.

• 1.35/1.5 (Initial)/2.0

Activates/deactivates bass.

• ON/OFF (Initial)

Adjusts the subwoofer level.*

• –50 to +10 (Initial: 0)

• To clear the adjustment, touch [EQ INIT].

3 Repeat step 2 to adjust the level of other

bands.

* Not adjustable when <None> is selected for subwoofer on the

<Speaker Select> screen. (Page 33)

Adjust the sound effect.

Adjusts loudness.

• OFF (Initial)/Low/High

Selects the bass boost level.

• OFF (Initial)/Level 1/Level 2/Level 3/Level 4/

Level5

Reduces the driving noise by raising the bandwidth.

• OFF (Initial)/ON

<Space Enhancement>*1

Virtually enhances the sound space using the Digital

Signal Processor (DSP) system. Select the enhance

level.

• OFF (Initial)/Small/Medium/Large

<K2>*2

Restores the sound lost due to audio compression to a

realistic sound.

• OFF/ON (Initial)

Virtually makes the sound more realistic using the

Digital Signal Processor (DSP) system. Select the sound

level.

• OFF (Initial)/Level 1/Level 2/Level 3

Moves the center of the sound to the lower or higher

point. Select the height.

• OFF (Initial)/Low/Middle/High

*1 You cannot change the setting when “Tuner” is selected as the

source.

*2 This function works only when “DISC”/ “USB”/ “iPod”/

“Android™” is selected as the source.

Touch [J]/[K]/[H]/[I] or drag the mark to adjust.

<Fader>

Adjusts the front and rear speaker output balance.

When using a two-speaker system, set the fader to the

center (0).

• F15 to R15 (Initial: 0)

32 ENGLISH

00_KW-V2018ST_M_ENG.indb 3200_KW-V2018ST_M_ENG.indb 32 17/6/2017 7:35:51 AM17/6/2017 7:35:51 AM

SettingsSettings

Adjusts the left and right speaker output balance.

• L15 to R15 (Initial: 0)

To clear the adjustment: Touch [Center].

Preparation:

Before making the adjustment for <Speaker/X'over>,

select the appropriate crossover network mode

according to the speaker system (2-way speaker

system or 3-way speaker system).

1 Turn off the AV source.

On the Home screen, touch as follows:

2 Display the <X’over Network> screen.

On the monitor panel, press the following buttons

at the same time:

• For KW-V340BT/KW-V340BTM: and

• For KW-V440BT/KW-V440BTM:

FNC and – (volume)

3 Select the crossover network mode.

[2way] Select this when 2-way system

speakers are used (front/rear).

[3way] Select this when 3-way system

speakers are used (tweeter/mid

range/woofer).

A confirmation message appears. Touch [Yes].

Setting the speakers and crossover

frequency

1 Select a car type (1), select the location

of the speakers (2)*, then display the

<Speaker Select> screen (3).

* Speaker location selection is available only when

<X’overNetwork> is set to [2way].

2 Select the speaker type (1), select the size

of the selected speaker (2), then display

the <X’over> screen (3).

• If a speaker is not connected, select <None>.

• When setting the front speakers, also select the

speaker size for <Tweeter>.

3 Adjust the crossover frequency of the

selected speaker.

• Adjustable items vary depending on the selected

speaker type/speaker size/crossover settings.

Adjusts the output volume of the tweeter (left/

right).

Adjusts the crossover frequency for the tweeter.

<Gain>

Adjusts the output volume of the selected speaker.

Adjusts the crossover frequency for the front or rear

speakers (high pass filter).

Adjusts the crossover frequency for the speaker

(low pass filter).

Adjusts the crossover slope.

<Phase>

Selects the phase for the speaker.

ENGLISH

00_KW-V2018ST_M_ENG.indb 3300_KW-V2018ST_M_ENG.indb 33 17/6/2017 7:35:51 AM17/6/2017 7:35:51 AM

SettingsSettings

Make fine adjustments to the delay time of the speaker

output to create a more suitable environment for your

car.

Select the listening position (1), select

[Distance] or [Gain](2) to make an

adjustment, then adjust each speaker setting

(3).

1 Select from <All>, <FrontL>, <Front R> or

<Front All>*.

2 Select an item to adjust.

[Distance] Adjusts the digital time alignment

value.

[Gain] Adjusts the output volume of the

selected speaker.

3 To determine the adjustment value, see the

following “Determining the value for <Position

DTA> adjustment”.

To initialize the setting value: Touch [Initialize].

* <Front All> is selectable only when <X'over Network> is set to

[2way].

Determining the value for <Position DTA>

adjustment

If you specify the distance from the center of the

currently set listening position to every speaker, the

delay time will be automatically computed and set.

1 Determine the center of the currently set

listening position as the reference point.

2 Measure the distances from the reference point

to the speakers.

3 Calculate the differences between the distance of

the furthest speaker and other speakers.

4 Set the DTA value calculated in step 3 for

individual speakers.

5 Adjust gain for individual speakers.

E.g. When <Front All> is selected as the listening

position

+90 cm

60 cm

80 cm

+70 cm

150 cm

+0 cm

Adjust and store the auto-adjustment volume level for

each source. If the source is a disc, the adjustment is

stored for each of the following categories:

• DVD/VCD

• CD

• DivX/MPEG1/MPEG2/MP3/WMA/WAV/AAC/FLAC

The volume level will automatically increase or

decrease when you change the source.

• –15 to +6 (Initial: 00)

Display settings

Display the <Display> screen.

On the Home screen, touch as follows:

Then, on the <Settings> screen, touch [Display].

E.g. Display settings screen for KW-V440BT

34 ENGLISH

00_KW-V2018ST_M_ENG.indb 3400_KW-V2018ST_M_ENG.indb 34 17/6/2017 7:35:51 AM17/6/2017 7:35:51 AM

SettingsSettings

• Auto (Initial): Dims the screen and button

illumination when you turn on the headlights.

– Connection to the car light control switch is

required. (Page 45)

• ON: Activates dimmer.

• OFF: Deactivates dimmer.

You can change the display design. While playing a

video or picture, you can capture an image and use

the captured image as a background.

• You cannot capture copyrighted content and images

from iPod/iPhone.

• When using a JPEG file as the background, make sure

that the resolution is 800 x 480 pixels.

• The color of the captured image may look different

from that of the actual scene.

For KW-V340BT/KW-V340BTM

1 Change the Home screen design

Display the Home screen design selection screen (1),

then select the Home screen design (2).

• The selectable background designs differ depending

on the selected Home screen design.

• When the Home screen design is changed, source

icon designs are also changed.

2 Change the background design

Display the background design selection screen (1),

select the dimmer setting (2) ([ ] : dimmer on or

[ ]: dimmer off), then select the background design

(3).

3 Change the illumination color of the buttons on

the monitor panel

Display the illumination color selection screen (1),

select the dimmer setting (2) ([ ] : Dimmer on or

[ ]: Dimmer off), then select the illumination color

(3).

• You can also adjust the color yourself. Touch [Edit] to

display the color adjustment screen, then select the

dimmer setting and adjust the color. The adjustment

is saved in [User].

• Selecting [Scan] changes the illumination color

gradually.

For KW-V440BT/KW-V440BTM

1 Change the background design

Display the background design selection screen (1),

then select the background design (2).

2 Change the illumination color of the

background design

Display the background color selection screen (1),

then select the background color (2).

When the one of these is selected, you can

change the background color.

35ENGLISH

00_KW-V2018ST_M_ENG.indb 3500_KW-V2018ST_M_ENG.indb 35 17/6/2017 7:35:51 AM17/6/2017 7:35:51 AM

• You can also adjust the color yourself. Press [Adjust]

to display the color adjustment screen, then adjust

the color. The adjustment is saved on [User].

3 Change the source icon design

Display the icon style selection screen (1), then select

the icon design (2).

Storing your own scene for the background

image

1 While playing a video or picture, display

the <User Customize> screen.

On the <Display> screen, touch as follows:

<User Customize>: [Enter]

2 Display the background design selection

screen, then touch the following:

• For KW-V340BT/KW-V340BTM: [ Capture]

• For KW-V440BT/KW-V440BTM: [User1 Select] or

[User2 Select]

3 Adjust the image (1), then capture the

image (2).

E.g. Image adjustment screen for KW-V440BT

[J][K][H][I]Moves the zooming frame.

[ ]

Magnifies the scene.

• <OFF>/<Zoom1>/<Zoom2>/

<Zoom3>

[IW]*Starts/pauses playback.

[ ] *Advances scenes frame by frame.

A confirmation message appears. Touch [Yes]

to store the newly captured image. (The existing

image is replaced with the new one.)

• To return to the previous screen, touch [No].

• To cancel the capture, touch [Cancel].

* Not displayed when playing an external component connected to

the AV-IN input terminal.

• ON: Displays the clock while a video source is

playing.

• OFF (Initial): Cancels.

• ON (Initial)*: Activates the display demonstration.

• OFF: Deactivates the display demonstration.

* For Indonesian models, the initial is <OFF>.

• ON: Scrolls the displayed information repeatedly.

• Once (Initial): Scrolls the displayed information once.

• OFF: Cancels.

Touching [H] scrolls the text regardless of this setting.

SettingsSettings

36 ENGLISH

00_KW-V2018ST_M_ENG.indb 3600_KW-V2018ST_M_ENG.indb 36 17/6/2017 7:35:52 AM17/6/2017 7:35:52 AM

Adjust the parking guidelines according to the size of

the car, parking space and so on.

When adjusting the parking guidelines, make sure to

use the parking brake to prevent the car from moving.

Select the mark (1), then adjust the position of the

selected mark (2).

Initialize

Make sure that A and B are horizontally parallel, and

that C and D are the same length.

• Touch and hold [Initialize ] for 2 seconds to set all

the marks to the initial default position.

(Only for KW-V340BT Region 3, KW-V340BTM

Region2, KW-V440BT Region 3 (except for Indonesian

models), KW-V440BTM Region 2)

Change the settings for displaying the screen of an

external navigation unit.

• To change the setting, turn off the AV source by

touching [AV Off] on the Home screen beforehand.

SettingsSettings

Adjust the brightness and blackness of the screen.

Select [DIM ON] (dimmer on) or [DIM OFF] (dimmer

off), then change the following settings:

Adjusts brightness.

• –15 to +15 (Initial: 0 for dimmer on, +15 for dimmer

off)

<Black>

Adjusts blackness.

• –10 to +10 (Initial: 0)

Select the color system of the external monitor.

• NTSC/PAL (Initial)

“Please Power Off” appears when the setting is

changed. Turn off the power, then turn on to enable

the change.

Select the viewing angle in relation to the monitor

panel to make the panel easier to see.

• Under 0° (Initial)/5°/10°/15°/20°

Input settings

Display the <Input> screen.

On the Home screen, touch as follows:

Then, on the <Settings> screen, touch [Input].

E.g. Input settings screen for KW-V440BT

Configure the rear view camera settings.

• ON (Initial): Displays the picture from the rear view

camera when you shift the gear to the reverse (R)

position.

–A caution message appears on the screen. To

remove the caution message, touch the screen.

• OFF: Select this when no camera is connected.

• ON (Initial): Displays the parking guidelines.

• OFF: Hides the parking guidelines.

ENGLISH

00_KW-V2018ST_M_ENG.indb 3700_KW-V2018ST_M_ENG.indb 37 17/6/2017 7:35:52 AM17/6/2017 7:35:52 AM

SettingsSettings

System settings

Display the <System> screen.

On the Home screen, touch as follows:

Then, on the <Settings> screen, touch [System].

E.g. System settings screen for KW-V440BT

Select the text language used for on-screen

information. For details, see “Initial settings” on

page4.

<Clock>

Set the clock. For details, see “Clock settings” on

page5.

Specify the connection method of Android/iPod/

iPhone.

1 Select the device type (1), then touch

[Change] (2).

2 Select the connection method (1), then

confirm the selection ([OK] or [Next]) (2).

If [iPod/iPhone] is selected in step 1:

[USB 1 Wire] Select this when the device is

connected via the USB input

terminal (on the monitor panel or

cable from the rear panel).

[Bluetooth] Select this when the device is

connected via Bluetooth. (Go to

step 3.)

<Input>

Select the source screen to be displayed when you

perform the following operation.

For KW-V340BT/KW-V340BTM: Press button on

the monitor panel.

For KW-V440BT/KW-V440BTM: Touch [ ] on the

pop-up short-cut menu.

• RGB: Switches to the navigation screen from the

connected navigation unit.

• OFF (Initial): Deactivates the display switch function.

Select which front speakers are used for the navigation

guidance.

• Lch: Output from front left channel only.

• Rch: Output from front right channel only.

• L+Rch (Initial): Output from both front left and front

right channels.

0 to 35: Adjust the volume of the navigation guidance.

(Only for KW-V440BT Region 3 (except for Indonesian

models), KW-V440BTM Region 2)

• ON: Enables to control TV operation on the “AV-IN”.

• OFF (Initial): Select this to use “AV-IN” with the other

component than TV Tuner.

38 ENGLISH

04_KW_V340BT_M_Body02.indd 3804_KW_V340BT_M_Body02.indd 38 5/7/2017 4:05:52 PM5/7/2017 4:05:52 PM

SettingsSettings

If [Android/Other] is selected in step 1:

The <Paired Device List> screen appears. Go to

step 3.

3 When selecting [Bluetooth] as the

connection method: Select the device (1),

then press [OK] (2) to connect.

• If the device is already connected, skip step 1.

Configure settings for using a Bluetooth device, such

as connection and other general operations. For

details, see “Bluetooth settings” on page 31.

(Only for KW-V340BT Region 3, KW-V340BTM

Region2, KW-V440BT Region 3 (except for Indonesian

models), KW-V440BTM Region 2)

Displays the serial number.

Adjust the touch positions of the buttons on the

screen.

Touch the center of the marks at the upper left (1),

the lower center (2), then the upper right (3) as

instructed.

• To reset the touch position, touch [Reset].

• To cancel the current operation, touch [Cancel].

<Beep>

• ON (Initial): Activates the key-touch tone.

• OFF: Deactivates the key-touch tone.

Memorize, recall, or clear the settings you have made.

• The memorized settings are kept even when the unit

is reset.

Touch [Yes] to display the setting screen, then select

an operation:

• Recall: Recalls the memorized settings.

• Memory: Memorizes the current settings.

• Clear: Clears the currently memorized settings.

• Cancel: Cancels.

A confirmation message appears. Touch [Yes].

<DivX(R) VOD>

This unit has its own Registration Code. Once you

have played back a file with the Registration Code

recorded, this unit’s Registration Code is overwritten

for copyright protection.

• Touch [Enter] to display the information.

• To return to the previous screen, touch [OK].

Initialize all settings you have made. Touch and hold

[Enter] to initialize the settings.

• After initializing the settings, adjust the settings on

the <Initial Settings> screen.

ENGLISH

00_KW-V2018ST_M_ENG.indb 3900_KW-V2018ST_M_ENG.indb 39 17/6/2017 7:35:53 AM17/6/2017 7:35:53 AM

SettingsSettings

Updates the system application.

Updates the system.

Updates the DVD system application.

The system update starts. It may take a while.

If the update has been completed successfully,

“Update Completed” appears, then reset the unit.

• Do not disconnect the USB device while updating.

• If the update has failed, turn the power off and then

on, and retry the update.

• Even if you have turned off the power during the

update, you can restart the update after the power

is turned on. The update will be performed from the

beginning.

Shows the Open Source Licenses.

• The unit can register/change all of the buttons’

functions at the same time. To do this, press all

buttons in turn and after pressing all of them, touch

[Done] on the <Steering Remote Control Setting>

screen. However, new functions cannot be learned

after this operation.

• When changing the functions already learned, touch

the assigned function you want to change in step 3

and then touch to select the new function from the

function list.

• Confirm the contents of the settable functions in the

function list. You cannot edit the function list.

To initialize the setting: Touch [Initialize] for

<Steering Remote Control Setting>.

• A confirmation message appears. Touch [Yes].

–To cancel the initialization, touch [No].

Update the system by connecting a USB device

containing an update file.

• To obtain the update file, visit

<http://www.jvc.net/cs/car/>.

Connect a USB device with the update file to the unit.

Assign functions to the keys of the remote controller

on the steering wheel.

• This function is available only when your car is

equipped with the electrical steering remote

controller.

• You can only register/change the functions while

you are parked.

• If your steering remote controller is not compatible,

learning may not be completed and an error

message may appear.

1 Touch [Set] for <Steering Remote Control

Setting> to display the setting screen.

2 Press and hold a button on the steering

remote controller to register or change.

3 Select a function to assign to the selected

button.

Sterring Remote Control Setting

VOL

Please select the function to assign to the button.

VOL

ATT

SRC

Done

4 Repeat steps 2 and 3 to register other

buttons.

5 Touch [Done] to finish procedure.

40 ENGLISH

00_KW-V2018ST_M_ENG.indb 4000_KW-V2018ST_M_ENG.indb 40 17/6/2017 7:35:53 AM17/6/2017 7:35:53 AM

Remote Controller Remote Controller

Remote controller, RM-RK258, is supplied for

KW-V340BT Region 3, KW-V340BTM Region 2,

KW-V440BT Region 3, KW-V440BTM Region 2.

• For KW-V340BT Region 4: To use the remote

controller, purchase optional remote controller,

RM-RK258.

Refer to the instruction manual that comes with the

remote controller.

* Remote sensor

DO NOT expose the remote sensor to bright light (direct sunlight

or artificial lighting).

Preparation

Removing the battery sheet

Pull the battery sheet out from the remote controller

to activate the battery.

Changing the battery of the remote

controller

CR2025 (+side)

• Use a commercially available button battery

(CR2025).

• Insert the battery with the + and – poles aligned

properly.

–If the effectiveness of the remote controller

decreases, replace the battery.

WARNINGS

• Do not ingest the battery, as it presents a

chemical burn hazard

The remote controller supplied with this product

contains a coin/button cell battery.

If the coin/button cell battery is swallowed, it can

cause severe internal burns in just 2 hours and can

lead to death.

Keep new and used batteries away from children.

If the battery compartment does not close securely,

stop using the product and keep it away from

children.

If you think batteries might have been swallowed or

placed inside any part of the body, seek immediate

medical attention.

CAUTION

• Do not leave the battery near fire or under direct

sunlight. A fire, explosion or excessive heat

generation may result.

• Do not set the remote controller in hot places such

as on the dashboard.

• Danger of explosion if Lithium battery is incorrectly

replaced. Replace only with the same or equivalent

type.

ENGLISH

04_KW_V340BT_M_Body02.indd 4104_KW_V340BT_M_Body02.indd 41 18/7/2017 10:26:49 AM18/7/2017 10:26:49 AM

Aim the remote controller directly at the remote

sensor on the unit. (Page 41)

Basic operations

ATT Attenuates/restores the sound.

DISP Displays the current source control

screen.

FM/J/AM/K• Selects the band.

• Selects a title/item/folder.

/ • Tuner:

–Searches for stations

automatically. (Press)*

–Searches for stations manually.

(Hold)*

• Selects a track. (Press)

VOL +/VOL – Adjusts the volume level.

Remote ControllerRemote Controller

SRC Selects the source.

I/W• Starts/pauses playback.

• Tuner: Changes the seek mode

(AUTO1, AUTO2, MANU).

Answers incoming calls.

0 – 9 Enters a number.

1 – 5 Enters a preset station number.

ANGLE Not used for this unit.

ASPECT Changes the aspect ratio.

• To check the current aspect ratio

setting, operate on the touch panel.

(Page<?>)

DIRECT Enters direct search mode.

CLR Erases the misentry.

* The search method differs according to the selected seek mode.

Searching for an item directly

While listening to the Tuner or during disc playback,

you can search for a station frequency/chapter/title/

folder/file/track directly using the number buttons.

• To search for a track from the VCD menu, perform

during PBC playback.

1 Press DIRECT to enter the search mode.

• Each time you press DIRECT, the item to search

for changes.

2 Press a number button to select a desired

item (station frequency/chapter/title/

folder/file/track).

• To erase a misentry, press CLR.

3 Press ENT to confirm.

To exit the search mode: Press DIRECT.

JVC Remote APP

JVC Remote is an application that connects and

controls compatible JVC car receivers via Bluetooth®

like a wireless remote control.

You can also operate this unit from a Smartphone

using JVC Remote APP.

This application can display the source information

of this unit on the smartphone’s screen, and enables

the user to make an audio setting using the graphic

user interface of this application.

This application also works as a free standalone

music player application, when your Smartphone is

not connected to this unit.

• For details, visit

<www.jvc.net/car/app/jvc_remote/>.

42 ENGLISH

04_KW_V340BT_M_Body02.indd 4204_KW_V340BT_M_Body02.indd 42 18/7/2017 10:26:49 AM18/7/2017 10:26:49 AM

Installation and Connection Installation and Connection

WARNINGS

• DO NOT connect the ignition wire (red) and the

battery wire (yellow) to the car chassis (ground), you

may cause a short circuit, that in turn may start a fire.

• DO NOT cut out the fuse from the ignition wire (red)

and the battery wire (yellow). The power supply must

be connected to the wires via the fuse.

• Always connect the ignition wire (red) and the

battery wire (yellow) to the power source running

through the fuse box.

CAUTIONS

• Install this unit in the console of your car.

• Do not touch the metal parts of this unit during and

shortly after the use of the unit. Metal parts such as

the heat sink and enclosure become hot.

• When parking at a low ceiling area, turn off the unit

to store the antenna. As when the unit is installed in

the car with the function of auto antenna; the radio

antenna extends automatically when you turn on

the unit with the antenna control wire (ANT. CONT)

connected. (Page 45)

Before installation

Precautions on installation and connection

• Mounting and wiring this product requires skills and

experience. For best safety, leave the mounting and

wiring work to professionals.

• Mount the unit so that the mounting angle is 30° or

less.

• Make sure to ground the unit to a negative 12V DC

power supply.

• Do not install the unit in a location exposed to direct

sunlight or excessive heat or humidity. Also avoid

places with too much dust or the possibility of water

splashing.

• Do not use your own screws. Use only the screws

provided. If you use the wrong screws, you could

damage the unit.

• After the unit is installed, check whether the brake

lamps, blinkers, wipers, etc. on the car are working

properly.

• Do not press hard on the panel surface when

installing the unit to the car. Otherwise scratches,

damage, or failure may result.

• If the power is not turned on (“Miswiring DC Offset

Error”, “Warning DC Offset Error” is displayed),

the speaker wire may have a short circuit or have

touched the chassis of the car and the protection

function may have been activated. In this case, the

speaker wire should be checked.

• Keep all cables away from heat dissipating metal

parts.

• If your car’s ignition does not have an ACC position,

connect the ignition wires to a power source that

can be turned on and off with the ignition key. If you

connect the ignition wire to a power source with a

constant voltage supply, such as with battery wires,

the battery may be drained.

• If the fuse blows, first make sure the wires are not

touching to cause a short circuit, then replace the old

fuse with one with the same rating.

• Insulate unconnected wires with vinyl tape or other

similar material. To prevent a short circuit, do not

remove the caps and do not let the cable out at the

ends of the unconnected wires or the terminals.

• Secure the wires with cable clamps and wrap vinyl

tape around the wires that comes into contact with

metal parts to protect the wires and to prevent short

circuit.

• Connect the speaker wires correctly to the terminals

to which they correspond. The unit may be damaged

or fail to work if you share the · wires or ground

them to any metal part in the car.

• When only two speakers are being connected to the

system, connect both connectors either to the front

output terminals or to the rear output terminals (do

not mix front and rear). For example, if you connect

the ª connector of the left speaker to a front output

terminal, do not connect the · connector to a rear

output terminal.

ENGLISH

00_KW-V2018ST_M_ENG.indb 4300_KW-V2018ST_M_ENG.indb 43 17/6/2017 7:35:53 AM17/6/2017 7:35:53 AM

Installation and ConnectionInstallation and Connection

Installing the trim plate

(Only for KW-V340BT Region 3, KW-V340BT Region 2,

KW-V340BTM Region 4)

Parts list for installation

Note: This parts list does not include all the package

contents.

¥ Wiring harness (× 1)

ø Extension wire, 2 m (× 1)

π Microphone, 3 m (× 1)

[ Flat head screw (× 6)

“ Round head screw (× 6)

] Steering remote cable (× 1)

‘ Trimplate (× 1)

(Only for KW-V340BT Region 3, KW-V340BT

Region 2, KW-V340BTM Region 4)

Installation procedure

1 Remove the key from the ignition and

disconnect the · battery.

2 Make the proper input and output wire

connections for each unit.

3 Connect the speaker wires of the wiring

harness.

4 Connect the wires of the wiring harness

in the following order: ground, battery,

ignition.

5 Connect the wiring harness to the unit.

6 Install the unit in your car.

Make sure that the unit is installed securely in place.

If the unit is unstable, it may malfunction (e.g., the

sound may skip).

7 Reconnect the · battery.

8 Press the reset button on the monitor

panel. (Page3)

9 Configure <Initial Settings>. (Page4)

Installing the unit

Installing using the mounting brackets

removed from the car

Select the appropriate type of screw for the mounting

brackets: flat head ([) or round head (“).

Installing in Toyota cars

Install onto the car bracket using the supplied screws

(“). Use the mounting holes (A or B) that fit the car

bracket.

Car bracket

[

“

[

“

Side view

44 ENGLISH

00_KW-V2018ST_M_ENG.indb 4400_KW-V2018ST_M_ENG.indb 44 17/6/2017 7:35:54 AM17/6/2017 7:35:54 AM

Installation and ConnectionInstallation and Connection

REVERSE

REMOTE CONT

STEERING WHEEL

REMOTE INPUT

P.CONT

ANT.CONT

PRK SW

Wiring connection

10 A fuse

Connect the antenna cord to the antenna terminal

USB input terminal (1 m)

Purple with white stripe

White

]

/ White with black stripe

[

Green

]

/ Green with black stripe

[

Gray

]

/ Gray with black stripe

[

Purple

]

/ Purple with black stripe

[

Orange with white stripe

Light blue with yellow stripe

Blue with white stripe (12 V 350 mA)

Red (Ignition wire)

Yellow (Battery wire)

Black (Ground wire)

Light green

To the car’s reverse lamp harness when using the optional rear view camera

To the car light control switch

To rear speakers (right) / Tweeters (right) for 3-way crossover

To front speakers (right) / Mid-range speakers (right) for 3-way crossover

To rear speakers (left) / Tweeters (left) for 3-way crossover

To front speakers (left) / Mid-range speakers (left) for 3-way crossover

Car battery

Car fuse

To the car chassis

To the OE remote adapter (not supplied) which is compatible with your car

To the power control terminal when using the optional power amplifier (Or)

To the control terminal of the motor antenna or to the power terminal for the booster amplifier of film-type antenna

Extension wire (

)

To the car’s parking brake detection switch harness

(For best safety, be sure to connect the parking sensor.)

Ignition key switch

*1 Only for KW-V340BT Region3, KW-V340BTM

Region2, KW-V440BT Region3 (except

for Indonesian models) and KW-V440BTM

Region2.

*2 Only for KW-V440BT Region3 (except for

Indonesian models) and KW-V440BTM

Region2.

45ENGLISH

00_KW-V2018ST_M_ENG.indb 4500_KW-V2018ST_M_ENG.indb 45 17/6/2017 7:35:54 AM17/6/2017 7:35:54 AM

References References

Maintenance

Cleaning the unit

• Do not use any solvent (for example, thinner,

benzine, etc.), detergent, or insecticide. This may

damage the monitor or the unit.

• Gently wipe the panel with a soft, dry cloth.

Handling discs

• Do not touch the recording surface of the disc.

• Do not stick tape etc. on the disc, or use a disc with

tape stuck on it.

• Do not use any accessories for the disc.

• Clean from the center of the disc and move outward.

• Clean the disc with a dry silicone or soft cloth. Do not

use any solvents.

• When removing discs from this unit, pull them out

horizontally.

• Remove burrs from the center hole and disc edge

before inserting a disc.

More information

About playable files

Audio files

• This unit can play back the following files with

following codec and extension code:

–For disc: MP3(.mp3), WMA(.wma), WAV(.wav),

AAC(.m4a)

–For USB mass storage class device: MP3(.mp3),

WMA(.wma), WAV(.wav), AAC(.aac, .m4a),

FLAC(.flac)

Installation and ConnectionInstallation and Connection

Connecting external components

1 Navigation input (NAV)*1

2 3rd party TV output (REMO OUT)*2

3 Steering wheel remote controller input (REMO-IN)

• Connect to the vehicle’s steering remote harness

using the Steering Remote cable (]). Contact

your JVC dealer for details.

4 Microphone input (MIC) (Page 45)

5 Audio video input (AV-IN)

Connect the following type of 4-pole mini plug:

Left audio

Right audio

Ground

Composite video

6 Video output (V-OUT)

7 Rear view camera input (R-CAM)

8 Output terminals*3

• Left output (White)

• Right output (Red)

REAR: Rear speaker preouts

FRONT: Front speaker preouts

SW: Subwoofer preouts

For 3-way crossover:

REAR: Tweeter preouts

FRONT: Mid range speaker preouts

SW: Woofer preouts

*1 Only for KW-V340BT Region 3, KW-V340BTM Region 2,

KW-V440BT Region 3 (except for Indonesian models),

KW-V440BTM Region 2.

*2 Only for KW-V440BT Region 3 (except for Indonesian models),

KW-V440BTM Region 2.

*3 When connecting an external amplifier, connect its ground wire

to the chassis of the car; otherwise the unit may be damaged.

46 ENGLISH

00_KW-V2018ST_M_ENG.indb 4600_KW-V2018ST_M_ENG.indb 46 17/6/2017 7:35:54 AM17/6/2017 7:35:54 AM

References References

• This unit can play back files that meet the conditions

below:

–Bit rate:

MP3: 8 kbps – 320 kbps

WMA: For disc: 5 kbps – 320 kbps

For USB : 32 kbps – 192 kbps

AAC: 16 kbps – 320 kbps

–Sampling frequency:

MP3: 16 kHz – 48 kHz

WMA: 8 kHz – 48 kHz

WAV: 44.1 kHz

AAC: 32 kHz – 48 kHz

FLAC: 8 kHz – 96 kHz

–Files recorded in VBR (variable bit rate), and have a

discrepancy in elapsed time indication

• This unit can show or display the following:

–Tag:

MP3: ID3 Tag (version 1.0/1.1/2.2/2.3/2.4)

WMA Tag

WAV Tag

AAC Tag

FLAC Tag

–Jacket picture:

Picture size: 32 × 32 to 1 232 × 672 resolution

Data size: less than 500 KB

File type: JPEG

• This unit cannot play back the following files:

–MP3 files encoded with MP3i and MP3 PRO format.

–MP3 files encoded with Layer 1/2.

–WMA files encoded with lossless, professional, and

voice format.

–WMA files which are not based upon Windows

Media® Audio.

–WMA/AAC files copy-protected with DRM.

–AAC files copy-protected with FairPlay (except

those stored on an iPod/iPhone).

–Files which have data such as AIFF, ATRAC3, etc.

Video files

• This unit can play back the following files with

following codec and extension code:

–DivX(.divx, .div, .avi) regardless of the letter case—

upper/lower

–MPEG1/MPEG2 (.mpg, .mpeg)

• Streams that conform to:

–DivX:

Audio: MP3 or Dolby Audio

–MPEG1/MPEG2:

Audio: MPEG1 Audio Layer-2 or Dolby Audio

Video: MPEG system/program stream

• Other playable conditions:

–DivX: Bit rate: 8 Mbps (maximum for average video

signals)

–MPEG1/MPEG2: File format: MP@ML (Main Profile at

Main Level)/SP@ML (Simple Profile at Main Level)/

MP@LL (Main Profile at Low Level)

–Maximum video file size: 2 GB

• This unit cannot play back the following files:

–DivX files encoded in the interlaced scanning

mode.

Picture files

• This unit can play back the following files with

following codec and extension code:

–JPEG(.jpg, .jpeg)

• Other playable conditions:

–Resolution: 32 × 32 to 8192 × 7680 (It may take

time to display the file depending on its resolution.)

–Baseline JPEG files

• This unit cannot play back the following files:

–Progressive JPEG files

–Lossless JPEG files

About disc playback

Playable disc types

• CD-DA: Audio CD, CD Text

• DVD Video: Region code: 2, 3 or 4 (depending on the

country and sales area)

• Dual Disc: DVD side

• VCD: Video CD (PBC compatible)

• DVD Recordable/Rewritable (DVD-R/-RW, +R/+RW)

–DVD Video: UDF bridge

–ISO 9660 level 1, level 2, Romeo, Joliet

–Other playable formats:

DVD-R recorded in multi-border format (except for

dual layer discs)

Finalized +R/+RW (Video format only)

• CD Recordable/Rewritable (CD-R/-RW):

–ISO 9660 level 1, level 2, Romeo, Joliet

• Other informations:

–While playing a DVD Video, DTS sound cannot be

reproduced or emitted from this unit.

–This unit can recognize a total of 5 000 files and

250 folders (a maximum of 999 files per folder) in a

recordable/rewritable disc.

–Use only “finalized” recordable/rewritable discs.

–This unit can play back multi-session recordable/

rewritable discs; however, unclosed sessions will be

skipped while playing.

ENGLISH

04_KW_V340BT_M_Body02.indd 4704_KW_V340BT_M_Body02.indd 47 5/7/2017 4:07:07 PM5/7/2017 4:07:07 PM

ReferencesReferences

Unplayable disc types and formats

• DVD-Audio/DVD-ROM discs

• SVCD (Super Video CD), CD-ROM, CD-I (CD-I Ready),

DTS-CD

• MPEG4/DivX/AAC (.aac)/FLAC/MKV/DVD–VR/

DVD+VR/DVD-RAM recorded on DVD-R/RW or

+R/+RW

• MPEG4/DivX/AAC (.aac)/FLAC/MKV recorded on

CD-R/RW

• DVD-RW dual layer discs

• +RW double layer discs

• Non-DVD side of a “DualDisc” which does not comply

with the “Compact Disc Digital Audio” standard

• Discs that are not round.

• Discs with coloring on the recording surface or discs

that are dirty.

• Recordable/Rewritable discs that have not been

finalized.

• 8 cm discs. Attempting to insert these discs using an

adapter may cause a malfunction.

• Some recordable/rewritable discs or files may not be

played back due to their characteristics or recording

conditions.

Language codes (for DVD language selection)

AA Afar GD Scots Gaelic

AB Abkhazian GL Galician

AF Afrikaans GN Guarani

AM Ameharic GU Gujarati

AR Arabic HA Hausa

AS Assamese HI Hindi

AY Aymara HR Croatian

AZ Azerbaijani HU Hungarian

BA Bashkir HY Armenian

BE Byelorussian IA Interlingua

BG Bulgarian IE Interlingue

BH Bihari IK Inupiak

BI Bislama IN Indonesian

BN Bengali, Bangla IS Icelandic

BO Tibetan IW Hebrew

BR Breton JA Japanese

CA Catalan JI Yiddish

CO Corsican JW Javanese

CS Czech KA Georgian

CY Welsh KK Kazakh

DZ Bhutani KL Greenlandic

EL Greek KM Cambodian

EO Esperanto KN Kannada

ET Estonian KO Korean (KOR)

EU Basque KS Kashmiri

FA Persian KU Kurdish

FI Finnish KY Kirghiz

FJ Fiji LA Latin

FO Faroese LN Lingala

FY Frisian LO Laothian

GA Irish LT Lithuanian

LV Latvian, Lettish SM Samoan

MG Malagasy SN Shona

MI Maori SO Somali

MK Macedonian SQ Albanian

ML Malayalam SR Serbian

MN Mongolian SS Siswati

MO Moldavian ST Sesotho

MR Marathi SU Sundanese

MS Malay (MAY) SW Swahili

MT Maltese TA Tamil

MY Burmese TE Telugu

NA Nauru TG Tajik

NE Nepali TH Thai

NO Norwegian TI Tigrinya

OC Occitan TK Turkmen

OM (Afan) Oromo TL Tagalog

OR Oriya TN Setswana

PA Panjabi TO Tonga

PL Polish TR Turkish

PS Pashto, Pushto TS Tsonga

QU Quechua TT Tatar

RM Rhaeto-Romance TW Twi

RN Kirundi UK Ukrainian

RO Rumanian UR Urdu

RW Kinyarwanda UZ Uzbek

SA Sanskrit VI Vietnamese

SD Sindhi VO Volapuk

SG Sangho WO Wolof

SH Serbo-Croatian XH Xhosa

SI Singhalese YO Yoruba

SK Slovak ZU Zulu

SL Slovenian

48 ENGLISH

00_KW-V2018ST_M_ENG.indb 4800_KW-V2018ST_M_ENG.indb 48 17/6/2017 7:35:54 AM17/6/2017 7:35:54 AM

ReferencesReferences

About USB playback

Important

Make sure all important data has been backed up to

avoid losing the data.

We bear no responsibility for any loss of data stored in

the devices while using this unit.

Playable files on a USB device

• This unit can play the following types of files stored

in a USB mass storage class device.

–JPEG/Divx/MPEG1/MPEG2/MP3/WMA/WAV/AAC

(.aac/.m4a)/FLAC

• This unit can recognize:

–A total of 5 000 files

–250 folders for video files and a maximum of 999

files per folder

–250 folders for photo files and a maximum of 999

files per folder

–999 folders for audio files and a maximum of 999

files per folder

• The maximum number of characters (when the

characters are 1 byte):

–Folder names: 50 characters

–File names: 50 characters

Notes on using a USB device

• Avoid using the USB device if it might affect driving

safety.

• When connecting with a USB cable, use a USB 2.0

cable.

• Electrostatic shock at connecting a USB device may

cause abnormal playback of the device. In this case,

disconnect the USB device then reset this unit and

the USB device.

• Do not pull out and connect the USB device

repeatedly while “Reading” is shown on the screen.

• Operation and power supply may not work as

intended for some USB devices.

• Do not leave a USB device in the car, or expose to

direct sunlight or high temperatures to prevent

deformation or damage to the device.

Unplayable USB device

• This unit may not play back files in a USB device

properly when using a USB extension cable.

• USB devices equipped with special functions such as

data security functions cannot be used with the unit.

• Do not use a USB device with 2 or more partitions.

• Depending on the shape of the USB devices and

connection ports, some USB devices may not be

attached properly or the connection might be loose.

• This unit may not recognize a memory card inserted

into a USB card reader.

About iPod/iPhone

Important

Make sure all important data has been backed up to

avoid losing the data.

We bear no responsibility for any loss of data stored in

the devices while using this unit.

iPod/iPhone that can be connected

• Via the USB terminal:

Made for

–iPod nano (7th Generation)

–iPod touch (6th Generation)

–iPod touch (5th Generation)

–iPhone 7 Plus

–iPhone 7

–iPhone SE

–iPhone 6S Plus

–iPhone 6S

–iPhone 6 Plus

–iPhone 6

–iPhone 5S

–iPhone 5C

–iPhone 5

–iPhone 4S

• Via Bluetooth:

Made for

–iPod touch (6th Generation)

–iPod touch (5th Generation)

–iPhone 7 Plus

–iPhone 7

–iPhone SE

–iPhone 6S Plus

–iPhone 6S

–iPhone 6 Plus

–iPhone 6

–iPhone 5S

–iPhone 5C

–iPhone 5

–iPhone 4S

ENGLISH

00_KW-V2018ST_M_ENG.indb 4900_KW-V2018ST_M_ENG.indb 49 17/6/2017 7:35:54 AM17/6/2017 7:35:54 AM

ReferencesReferences

Notes on using an iPod/iPhone

• When operating an iPod/iPhone, some operations

may not be performed correctly or as intended. In

this case, visit the following JVC web site:

<http://www.jvc.net/cs/car/>

• When you turn on this unit, the iPod/iPhone is

charged through the unit.

• The text information may not be displayed correctly.

• For some iPod/iPhone models, the performance may

be abnormal or unstable during operation. In this

case, disconnect the iPod/iPhone device, then check

its condition.

If the performance is not improved or slow, reset

your iPod/iPhone.

Troubleshooting Troubleshooting

What appears to be trouble is not always serious.

Check the following points before calling a service

center.

• For operations with external components, refer also

to the instructions supplied with the adapters used

for connection (as well as the instructions supplied

with the external components).

General

No sound comes out of the speakers.

Adjust the volume to the optimum level.

Check the cords and connections.

No picture is displayed on the screen.

Turn on the screen. (Page4)

The unit does not work at all.

Reset the unit. (Page3)

The remote controller* does not work.

Replace the battery.

* For KW-V340BT Region 4: Purchase optional remote controller,

RM-RK258.

“No Signal”/“No Video Signal” appears.

Start playback on the external component

connected to the AV-IN input terminal.

Check the cords and connections.

Signal input is too weak.

“Miswiring DC Offset Error”/“Warning DC Offset

Error” appears.

A speaker cord has shorted or it has come into

contact with the car chassis. Wire or insulate the

speaker cord as appropriate, then reset the unit.

“Parking off” appears.

No playback picture is shown when the parking

brake is not engaged.

“No Navigation” appears.

No navigation unit is connected.

Discs

Recordable/Rewritable discs cannot be played

back.

Insert a finalized disc.

Finalize the discs with the component which you

used for recording.

Tracks on the Recordable/Rewritable discs cannot

be skipped.

Insert a finalized disc.

Finalize the discs with the component which you

used for recording.

Playback does not start.

The format of files is not supported by the unit.

No picture appears on the external monitor.

Connect the video cord correctly.

Select the correct input on the external monitor.

DivX/MPEG1/MPEG2/MP3/WMA/WAV/AAC discs

cannot be played back.

Record the tracks using a compatible application

on the appropriate discs. (Page47)

Add appropriate extension codes to the file names.

Tracks on the recordable/rewritable discs are not

played back as you have intended them to play.

Playback order may differ from the one played back

using other players.

50 ENGLISH

00_KW-V2018ST_M_ENG.indb 5000_KW-V2018ST_M_ENG.indb 50 17/6/2017 7:35:55 AM17/6/2017 7:35:55 AM

TroubleshootingTroubleshooting

iPod/iPhone

No sound comes out of the speakers.

Disconnect the iPod/iPhone, then connect it again.

Select another source, then reselect “iPod”.

The iPod/iPhone does not turn on or does not

work.

Check the connection.

Update the firmware version.

Charge the battery.

Reset the iPod/iPhone.

Sound is distorted.

Deactivate the equalizer either on this unit or the

iPod/iPhone.

A lot of noise is generated.

Turn off (uncheck) “VoiceOver” on the iPod/ iPhone.

For details, visit <http://www.apple.com>.

No operations are available when playing back a

track containing artwork.

Operate the unit after the artwork has loaded.

“Authorization Error” appears.

Check whether the connected iPod/iPhone is

compatible with this unit. (Page49)

Tuner

SSM automatic presetting does not work.

Store stations manually. (Page18)

Static noise while listening to the radio.

Connect the antenna firmly.

Android

Sound cannot be heard during playback.

Reconnect the Android device.

When <Android Setup> is set to [AUDIO MODE],

launch any media player application on the

Android device and start playback.

Sound output only from the Android device.

When <Android Setup> is set to [AUDIO MODE],

relaunch the current media player application or

use another media player application.

Restart the Android device.

If this does not solve the problem, the connected

Android device is unable to route the audio signal

to unit.

Cannot play back when <Android Setup> is set to

[AUTO MODE].

Make sure JVC Music Play APP is installed on the

Android device.

Reconnect the Android device and select the

appropriate control mode.

If this does not solve the problem, the connected

Android device does not support the Auto Mode.

“NO DEVICE” or “READING” keeps flashing.

Switch off the developer options on the Android

device.

Reconnect the Android device.

If this does not solve the problem, the connected

Android device does not support the Auto Mode.

“Region Code Error” appears.

You have inserted a DVD Video disc of an incorrect

region code. Insert a correct region code disc.

USB

“Reading” does not disappear from the screen.

Turn the power off and on again.

While playing a track, sound is sometimes

interrupted.

The tracks are not properly copied into the USB

device. Copy the tracks again, and try again.

Tracks are not played back as you have intended

them to play.

Playback order may differ from the one played back

using other players.

The source does not change to “USB” when you

connect a USB device while listening to another

source or “USB Device Error” appears when you

connect a USB device.

The USB port is drawing more power than the

design limit.

Turn the power off and unplug the USB device.

Then, turn on the power and reattach the USB

device.

If the above does not solve the problem, turn

the power off and on (or reset the unit) before

replacing with another USB device.

ENGLISH

00_KW-V2018ST_M_ENG.indb 5100_KW-V2018ST_M_ENG.indb 51 17/6/2017 7:35:55 AM17/6/2017 7:35:55 AM

TroubleshootingTroubleshooting

AV-IN

No picture appears on the screen.

Turn on the video component if it is not on.

Connect the video component correctly.

Spotify

The application does not work.

The application on your iPod touch/iPhone/

Android is not the latest version. Update the

application.

Pandora*/Spotify

The application does not work.

The application on your iPod touch/iPhone/

Android is not the latest version. Update the

application.

“Please update Pandora App” appears.

The Pandora application on your iPod touch/

iPhone/Android is not the latest version. Update

the application.

“Please check device.” appears.

The Pandora application on your iPod touch/

iPhone/Android has not started up.

The Pandora application is not installed on the

connected device.

An error has occurred on the Pandora application.

“Login Error” appears.

You have not been signed into Pandora.

“No skips remaining” appears.

No more songs can be skipped.

Bluetooth

Phone sound quality is poor.

Reduce the distance between the unit and the

Bluetooth mobile phone.

Move the car to a place where you can get a better

signal reception.

The sound is interrupted or skipped while using a

Bluetooth audio player.

Reduce the distance between the unit and the

Bluetooth audio player. Disconnect the device

connected for Bluetooth phone.

Turn off, then turn on the unit.

(When the sound is not yet restored) connect the

player again.

The connected audio player cannot be controlled.

Check whether the connected audio player

supports AVRCP (Audio/Video Remote Control

Profile).

The Bluetooth device does not detect the unit.

Search from the Bluetooth device again.

The unit does not pair with the Bluetooth device.

For devices compatible with Bluetooth 2.1:

For devices compatible with Bluetooth 2.0:

Enter the same PIN code for both the unit and

target device. If the PIN code of the device is not

indicated in its instructions, try “0000” or “1234.”

Turn off, then turn on the Bluetooth device.

Echo or noise occurs.

Adjust the microphone unit position.

Adjust the echo volume or noise reduction volume.

(Page28)

“Failed to save your thumb rating” appears.

Thumb-up/down is prohibited.

“No Station” appears.

No station is available.

“No Active Station” appears.

No station is being played.

“Station limit reached” appears.

The station list is full and no more stations can be

registered.

“Failed to save your bookmark” appears.

The unit has failed to save a bookmark. Try the

operation again.

“Limited Connectivity” appears.

The connection with the Pandora application

cannot be established.

“Pandora not available” appears.

You cannot use the Pandora application from

the area where you are currently trying to access

Pandora.

“Try again later” appears.

The Pandora server is under maintenance.

“Station does not exist” appears.

The selected station has been deleted by another

device or has expired.

“Cannot create a Station” appears.

You cannot create a station during the read-

only mode or when network connection is not

established.

* Only for KW-V340BT Region 4.

52 ENGLISH

00_KW-V2018ST_M_ENG.indb 5200_KW-V2018ST_M_ENG.indb 52 17/6/2017 7:35:55 AM17/6/2017 7:35:55 AM

TroubleshootingTroubleshooting

The unit does not respond when you try to copy

the phone book to the unit.

You may have tried to copy the same entries (as

stored) to the unit.

“Connection Error” appears.

The device is registered but the connection has

failed. Connect the registered device. (Page27)

“Please Wait...” appears.

The unit is preparing to use the Bluetooth function.

If the message does not disappear, turn off and

turn on the unit, then connect the device again (or

reset the unit).

“No Voice Device” appears.

The connected mobile phone does not have a

voice recognition system.

“No Data” appears.

No phone book data is contained in the connected

Bluetooth phone.

“Initialize Error” appears.

The unit has failed to initialize the Bluetooth

module. Try the operation again.

“Dial Error” appears.

Dialing has failed. Try the operation again.

“Hung Up Error” appears.

The call has not ended yet. Park your car, and use

the connected mobile phone to end the call.

“Pick Up Error” appears.

The unit has failed to receive a call.

Specifications Specifications

Monitor section

Picture Size (W × H) KW-V340BT/KW-V340BTM:

6.2 inches (diagonal) wide

137.5 mm × 77.2 mm

KW-V440BT/KW-V440BTM:

6.75 inches (diagonal) wide

151.8 mm × 79.68 mm

Display System Transparent TN LCD panel

Drive System TFT active matrix system

Number of Pixels 1 152 000

(800H × 480V × RGB)

Effective Pixels 99.99%

Pixel Arrangement RGB striped arrangement

Back Lighting LED

USB interface section

USB Standard USB 2.0 Full Speed/High

Speed

Compatible Device Mass Storage Class

File System FAT 16/32

Maximum Power

Supply Current DC 5 V 1.5 A

D/A Converter 24 bit

Audio Decoder MP3/WMA/AAC (.aac/.m4a)/

WAV/FLAC

Video Decoder DivX/MPEG1/MPEG2/JPEG

DVD player section

D/A Converter 24 bit

Audio Decoder Linear PCM/Dolby Audio/

MP3/WMA/WAV/AAC (.m4a)

Video Decoder DivX/MPEG1/MPEG2/JPEG

Wow & Flutter Below Measurable Limit

Frequency Response 96 kHz Sampling:

20 Hz to 22 000 Hz

48 kHz Sampling:

20 Hz to 22 000 Hz

44.1 kHz Sampling:

20 Hz to 20 000 Hz

Total Harmonic

Distortion

0.010% (1 kHz)

Signal to Noise Ratio 99 dB (DVD-Video 96 kHz)

Dynamic Range 99 dB (DVD-Video 96 kHz)

Disc Format DVD-Video/VIDEO-CD/CD-DA

Sampling Frequency 44.1 kHz/48 kHz/96 kHz

Quantifying Bit

Number

16 bit/20 bit/24 bit

ENGLISH

00_KW-V2018ST_M_ENG.indb 5300_KW-V2018ST_M_ENG.indb 53 17/6/2017 7:35:55 AM17/6/2017 7:35:55 AM

FM tuner section

Frequency Range 87.5 MHz to 108.0 MHz

(50kHz)

Usable Sensitivity

(S/N: 30 dB, 22.5 kHz)

6.2 dBf (0.56 μV/75 Ω)

Quieting Sensitivity

(S/N: 46 dB, 22.5 kHz)

15.2 dBf (1.58 μV/75 Ω)

Frequency Response

(±3.0 dB)

30 Hz to 15 kHz

Signal to Noise Ratio 68 dB (MONO)

Selectivity (±400 kHz) > 80 dB

Stereo Separation 40 dB (1 kHz)

AM tuner section

Frequency Range KW-V340BT Region 3/

KW-V440BT Region3:

531 kHz to 1 611 kHz (9 kHz)

KW-V340BTM Region2/

KW-V440BTM Region 2:

531 kHz to 1 602 kHz (9 kHz)

KW-V340BT Region 4:

531 kHz to 1 701 kHz (9 kHz)

Usable Sensitivity 28.5 dBμ

SpecificationsSpecifications

Bluetooth section

Technology Bluetooth 3.0

Frequency 2.402 GHz to 2.480 GHz

Output Power +4 dBm (MAX), 0 dBm (AVE),

Power Class 2

Maximum

Communication

Range

Line of sight approx. 10 m

Audio Codec SBC/AAC

Profile HFP (Hands Free Profile) 1.6

A2DP (Advanced Audio

Distribution Profile) 1.3

AVRCP (Audio/Video Remote

Control Profile) 1.5

GAP (Generic Access Profile)

PBAP (PhoneBook Access

Profile) 1.2

SDP (Service Discovery Profile)

SPP (Serial Port Profile) 1.2

DSP section

Equalizer 13 Band

Band Frequency (Hz) (BAND1 – 13):

62.5/100/160/250/400/630/

1k/1.6k/2.5k/4k/6.3k/10k/

16k

Level:

−09 to +09 (−9 dB to +9 dB)

Q: 1.35/1.5/2.0

HPF (High Pass Filter) Frequency (Hz):

Through/30/40/50/60/70/

80/90/100/120/150/180/

220/250

Slope (dB/Oct.):

–6/–12/–18/–24

Gain (dB):

–8/–7/–6/–5/–4/–3/–2/–1/0

LPF (Low Pass Filter) Frequency (Hz):

30/40/50/60/70/80/90/100/

120/150/180/220/250/

Through

Slope (dB/Oct.):

–6/–12/–18/–24

Gain (dB):

–8/–7/–6/–5/–4/–3/–2/–1/0

Video section

Color System of

External Video Input

NTSC/PAL

External Video Input

Level (RCA jack)/

(mini jack)

1 Vp-p/75 Ω

Video Output Level

(RCA jack)

1 Vp-p/75 Ω

Analog RGB Input KW-V340BT Region 3/

KW-V340BTM Region2/

KW-V440BT Region 3 (except

for Indonesian models)/

KW-V440BTM Region 2:

0.7 Vp-p/75 Ω

54 ENGLISH

00_KW-V2018ST_M_ENG.indb 5400_KW-V2018ST_M_ENG.indb 54 17/6/2017 7:35:55 AM17/6/2017 7:35:55 AM

SpecificationsSpecifications

Audio section

Maximum Power

(Front & Rear)

50 W × 4

Full Bandwidth

Power (Front & Rear)

22 W × 4

(at less than 1% THD)

Preout Level 4 V/10 kΩ

Preout Impedance ≤ 600 Ω

Speaker Impedance 4 Ω to 8 Ω

General

Operating Voltage 14.4 V

(10.5 V to 16 V allowable)

Maximum Current

Consumption

10 A

Installation Size

(Main Unit)

(W × H × D)

178 mm × 100 mm × 162 mm

Operational

Temperature Range

–10°C to +60°C

Weight (Main Unit) 1.7 kg

Design and specifications are subject to change

without notice.

ENGLISH

00_KW-V2018ST_M_ENG.indb 5500_KW-V2018ST_M_ENG.indb 55 17/6/2017 7:35:55 AM17/6/2017 7:35:55 AM

SpecificationsSpecifications

Trademarks and licenses

• Dolby, Dolby Audio and the double-D symbol are

trademarks of Dolby Laboratories.

• “DVD Logo” is a trademark of DVD Format/Logo

Licensing Corporation registered in the US, Japan

and other countries.

• The “AAC” logo is a trademark of Dolby Laboratories.

• Microsoft and Windows Media are either registered

trademarks or trademarks of Microsoft Corporation in

the United States and/or other countries.

• “Made for iPod,” and “Made for iPhone” mean that an

electronic accessory has been designed to connect

specifically to iPod, or iPhone, respectively, and

has been certified by the developer to meet Apple

performance standards.

Apple is not responsible for the operation of this

device or its compliance with safety and regulatory

standards. Please note that the use of this accessory

with iPod, or iPhone may affect wireless performance.

iPhone, iPod, iPod classic, iPod nano, and iPod touch

are trademarks of Apple Inc., registered in the U.S.

and other countries.

• Lightning is a trademark of Apple Inc.

• This item incorporates copy protection technology

that is protected by U.S. patents and other

intellectual property rights of Rovi Corporation.

Reverse engineering and disassembly are prohibited.

• Font for this product is designed by Ricoh.

• Android is a trademark of Google Inc.

• The Bluetooth® word mark and logos are registered

trademarks owned by Bluetooth SIG, Inc. and any

use of such marks by JVC KENWOOD Corporation is

under license. Other trademarks and trade names are

those of their respective owners.

• THIS PRODUCT IS LICENSED UNDER THE AVC PATENT

PORTFOLIO LICENSE FOR THE PERSONAL USE OF A

CONSUMER OR OTHER USES IN WHICH IT DOES NOT

RECEIVE REMUNERATION TO

(i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC

STANDARD ("AVC VIDEO") AND/OR (ii) DECODE

AVC VIDEO THAT WAS ENCODED BY A CONSUMER

ENGAGED IN A PERSONAL ACTIVITY AND/OR WAS

OBTAINED FROM A VIDEO PROVIDER LICENSED TO

PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR

SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL

INFORMATION MAY BE OBTAINED FROM MPEG LA,

L.L.C. SEE HTTP://WWW.MPEGLA.COM

• SPOTIFY and the Spotify logo are among the

registered trademarks of Spotify AB.

• Pandora, the Pandora logo, and the Pandora trade

dress are trademarks or registered trademarks of

Pandora Media, Inc., used with permission.

• libFLAC

Redistribution and use in source and binary forms,

with or without modification, are permitted provided

that the following conditions are met:

–Redistributions of source code must retain the

above copyright notice, this list of conditions

and the following disclaimer.

–Redistributions in binary form must reproduce the

above copyright notice, this list of conditions and

the following disclaimer in the documentation and/

or other materials provided with the distribution.

–Neither the name of the Xiph.org Foundation

nor the names of its contributors may be used

to endorse or promote products derived from

this software without specific prior written

permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT

HOLDERS AND CONTRIBUTORS “AS IS” AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING,

BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL

THE FOUNDATION OR CONTRIBUTORS BE LIABLE

FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,

EXEMPLARY, OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT

OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,

DATA, OR PROFITS; OR BUSINESS INTERRUPTION)

HOWEVER CAUSED AND ON ANY THEORY OF

LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,

OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)

ARISING IN ANY WAY OUT OF THE USE OF THIS

SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGE.

• DIVX

–This DivX Certified® device can play DivX® Home

Theater video files up to 576p (including .avi, .divx).

Download free software at www.divx.com to

create, play and stream digital video.

–DivX®, DivX Certified® and associated logos are

trademarks of DivX, LLC and are used under license.

56 ENGLISH

00_KW-V2018ST_M_ENG.indb 5600_KW-V2018ST_M_ENG.indb 56 17/6/2017 7:35:55 AM17/6/2017 7:35:55 AM

00_KW-V2018ST_M_ENG.indb 5700_KW-V2018ST_M_ENG.indb 57 17/6/2017 7:35:55 AM17/6/2017 7:35:55 AM

For updated information (the latest Instruction Manual, system updates, new functions, etc.),

please visit the following website:

<http://www.jvc.net/cs/car/>

00_KW-V2018ST_M_ENG.indb 100_KW-V2018ST_M_ENG.indb 1 17/6/2017 7:35:55 AM17/6/2017 7:35:55 AM

JVC KW V340BTM KW_V340BT_M User Manual V340BTM, V440BTM B5A 2150 00

KW-V440BT KW-V440BT, KW-V440BTM B5A_2150_00 English, (Instruction manual) Asia

KW-V340BT KW-V340BT, KW-V340BTM, KW-V440BT, KW-V440BTM B5A_2150_00 English, (Instruction manual) Asia

KW-V340BT, KW-V340BTM KW-V340BT, KW-V340BTM (Instruction manual) Asia B5A_2150_00

Navigation menu

Versions of this User Manual:

Views

Navigation