JVC XV N212S N210B/XV User Manual GNT0057 001A
XV-N210B XV-N210B, XV-N212S GNT0057-001A English,
User Manual: JVC XV-N212S XV-N212S English,
Open the PDF directly: View PDF 
.
Page Count: 2
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
Caution –– STANDBY/ON button!
Disconnect the mains plug to shut the power off
completely. The STANDBY/ON button in any
position does not disconnect the mains line. The power
can be remote controlled.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no
user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and invisible laser radiation when
open and interlock failed or defeated. Avoid direct
exposure to beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL,
PLACED INSIDE THE UNIT.
CAUTION:
•Do not block the ventilation openings or holes. (If the
ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to
get out.)
• Do not place any naked flame sources, such as
lighted candles, on the apparatus.
•When discarding batteries, environmental problems
must be considered and local rules or laws
governing the disposal of these batteries must be
followed strictly.
• Do not expose this apparatus to rain, moisture,
dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the
apparatus.
.
Precautions
Notes on the power cord
• When you are away on travel or otherwise for an
extended period of time, remove the plug from the
wall outlet. A small amount of power (2.0 W) is always
consumed while the power cord is connected to the
wall outlet.
• When unplugging the player from the wall outlet,
always pull the plug, not the power cord.
• Do not handle the power cord with wet hands!
• Disconnect the power cord before cleaning the
player or moving the player.
• Do not alter, twist or pull the power cord, or put
anything heavy on it, which may cause fire, electric
shock, or other accidents.
•If the cord is damaged, consult a dealer and have the
power cord replaced with a new one.
Avoid moisture, water, dust, and high temperatures
• Do not place the player in moist or dusty places.
•If water gets inside the player, turn off the power and
remove the plug from the wall outlet, then consult
your dealer. Using the player in this state may cause
a fire or electrical shock.
•Do not expose the player to direct sunlight or place it
near a heating device.
Notes on installation
•Select a place which is level, dry and neither too hot
nor too cold between 5˚C and 35˚C (41˚F and 95˚F).
•Leave sufficient distance between the player and the
TV.
• Do not install the player in a place subject to
vibrations.
• Do not put heavy objects on the player.
To prevent malfunction of the player
• There are no user-serviceable parts inside. If
anything goes wrong, unplug the power cord and
consult your dealer.
• Do not insert any metallic objects, such as wires,
hairpins, coins, etc. into the player.
• Do not block the vents. Blocking the vents may
damage the player.
To clean the cabinet
• Use a soft cloth. Follow the relevant instructions on
the use of chemically-coated cloths.
• Do not use benzene, thinner or other organic
solvents and disinfectants. These may cause
deformation or discoloring.
Playable discs
• DVD VIDEO, SVCD, Video CD, Audio CD
• DVD-R/-RW written in the DVD VIDEO format
•CD-R/RW written in the SVCD, Video CD or Audio CD
format
• CD-R/RW written in MP3/JPEG/MPEG-4 in
accordance with the “ISO 9660” format
Supported Digital audio formats:
Linear PCM, Dolby Digital, DTS (Digital Theater Systems)
NOTES
•If a disc gets dirty, scratched or warped, or due to the
disc characteristics or recording conditions, the
player may not be able to play back such discs.
• The player can play back audio signals recorded in
MIX-MODE CD, CD-G, CD-EXTRA and CD TEXT.
• With some discs, operations may not be possible.
Unplayable discs
If you try to play back discs listed below, noise may
generate causing damage to speakers.
• DVD-RW written in the VR format
• DVD-ROM, DVD-RAM, DVD AUDIO, CD-ROM,
PHOTO CD, SACD
• Unfinalized discs
• Discs of irregular shape or discs with tape, seals or
paste on either the label side or playback side.
Playing back these discs may damage the player.
VIDEO
Advanced Operations
213
546
879
010 +10
DISPLAY
/DIMMER
SOUND
EFFECT
SLIDE EFFECT
THUMBNAIL
/LIST
MENU
SET
PREVIOUS SELECT
CLEAR
NEXT
ENTER
ZOOM
TITLE
/GROUP RETURN CANCEL
STANDBY/ON
I/P ON SCREENSLOW
ANGLE SUB TITLE AUDIO
UP
P TO MENU
Changing the picture tone (VFP)
The VFP (Video Fine Processor)
function allows you to adjust the
picture character according to the
type of programming, picture tone or
personal preferences.
1Press VFP-I/P.
2Press 2/3 to select the desired
preset.
NORMAL For watching TV in a
general room.
CINEMA For watching a movie
software in a room with
suppressed light.
USER1
USER2
You can adjust
parameters that affect the
picture character and
store the settings as a user
preset.See below.
To adjust the picture tone
1Select “USER1” or “USER2.”
2Press 5/∞ to select a parameter, then press ENTER.
3Press 5/∞ to adjust the parameter, then press ENTER.
4Repeat step 2 and 3 to adjust other parameters.
5Press VFP-I/P to finish the setting.
USER 1
BRIGHTNESS
GAMMA
CONTRAST
SATURATION
TINT
SHARPNESS
Y DELAY
+ 4
MID
+10
+10
+10
LOW
+ 2
Selected
Preset
Parameter
GAMMA Adjust this if the neutral color is bright or dark.
The brightness of dark and bright portion is
maintained (LOW/MID/HIGH).
BRIGHTNESS Adjust this if the picture is bright or dark on the
whole (–16 (darkest) to +16 (brightest)).
CONTRAST Adjust this if the far and near position is
unnatural (–12 to +12).
SATURATION Adjust this if the picture is whitish or blackish
(–16 (blackest) to +16 (whitest)).
TINT Adjust this if the appearance of flesh tone is
unnatural (–16 to +16).
SHARPNESS Adjust this if the picture is indistinct (LOW/
HIGH).
Y DELAY Adjust this if the picture looks separately/
overlapped (–2 to +2).
Changing the Sound Field
You can change the sound field only
for analog audio output.
Each time you press SOUND
EFFECT, the Sound Effect mode
changes.
• As the value becomes bigger, the
Sound Effect works stronger.
Zooming the picture
Each time you press ZOOM, the
magnification changes.
• You can use 5/∞/2/3 button to
move the zoomed position.
To return the normal playback, select
the normal size by pressing ZOOM
repeatedly.
Changing the language, sound
and scene angle
1Press the button.
2Press the button repeatedly or
5/∞ to select the desired item.
3Press ENTER to finish the
setting.
Buttons To do
AUDIO For DVD Video:
select audio languages.
For SVCD/VCD/CD:
select the audio
channel.
SUBTITLE select the subtitle.
ANGLE select the view-angle.
DVD PLAYER
XV-N210B
XV-N212S
INSTRUCTIONS
©2004 Victor Company of Japan, Limited
• Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
• “DTS” and “DTS 2.0+Digital Out” are trademarks of
Digital Theater Systems, Inc.
• USE OF THIS PRODUCT IN ANY MANNER THAT
COMPLIES WITH THE MPEG-4 VISUAL STANDARD
IS PROHIBITED, EXCEPT FOR USE BY A
CONSUMER ENGAGING IN PERSONAL AND NON-
COMMERCIAL ACTIVITIES.
• This product incorporates copyright protection
technology that is protected by U.S. patents and
other intellectual property rights. Use of this
copyright protection technology must be authorized
by Macrovision, and is intended for home and other
limited viewing uses only unless otherwise
authorized by Macrovision. Reverse engineering or
disassembly is prohibited.
Warnings, Cautions and Others
GNT0057-001A[J/UJ]
EN 0804STHMDWJSC
Region code of DVD VIDEO
This player can play back DVD VIDEO discs
whose region code numbers include “1.”
Examples of playable DVD VIDEO discs:
The player’s region code is printed on the rear of
the player
Note of Color system format
This player accommodates the NTSC system, and
also can play back discs recorded with PAL
system. (PAL video signals are converted to an
NTSC signal and output.)
Supplied accessories
If anything is missing, consult your dealer
immediately.
• Audio/video cable (Yellow/White/Red) (x 1)
• Remote control (x 1)
• Lithium battery CR2032 (x 1)
• AC power plug adaptor (x 1) (for PX model
ONLY)
For customer use
Enter below the Model No. and Serial No. which are
located either on the rear, bottom or side of the cabinet.
Retain this information for future reference.
Model No.
Serial No.:
VIDEO
ALL
1
51
4
2
3
1
231
564
The lightning flash with arrowhead
symbol, within an equilateral triangle is
intended to alert the user to the presence
of uninsulated “dangerous voltage” within
the products enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompanying
the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
For U.S.A.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
For Canada
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT
For Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE
CLASS B LIMITS FOR RADIO NOISE EMISSIONS
FORM DIGITAL APPARATUS AS SET OUT IN THE
INTERFERENCE-CAUSING EQUIPMENT STANDARD
ENTITLED “DIGITAL APPARATUS,” ICES-003 OF THE
DEPARTMENT OF COMMUNICATIONS.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
Turning on the power
Inserting the AC power plug
After all other connections have been made, insert the
AC power plug to the wall outlet firmly.
For PX model only
The STANDBY indicator lights in red.
Installing the battery in the remote control
Precautions of the safe use of battery
• Store the battery in a place where children cannot
reach. If a child accidentally swallows the battery,
consult a doctor immediately.
• Do not recharge, short, disassemble or heat the
battery or dispose of it in a fire.
Doing any of these things may cause the battery to
give off heat, crack, or start a fire.
•Do not leave the battery with other metallic materials.
Doing this may cause the battery to give off heat,
crack, or start a fire.
•When throwing away or saving the battery, wrap it in
tape and insulate; otherwise, the battery may start to
give off heat, crack, or start a fire.
•Do not poke the battery with tweezers or similar tools.
Doing this may cause the battery to give off heat,
crack, or start a fire.
•Dispose of batteries in the proper manner, according
to federal, state, and local regulations.
Turning on and off the player
Press STANDBY/ON.
For PX model only
The STANDBY/ON indicator in red on the front panel
goes off.
Initial setup
When you turn on the player for the first time after
purchase, the following message appears on the TV
screen.
EXECUTE DVD PLAYER SETUP? - BASIC PICTURE/AUDIO
SETTING
YES - PRESS ENTER NO - PRESS CANCEL
Before enjoying this unit, make the initial settings as
follows:
1Press ENTER.
2Press 5/∞ to select the on-screen language for
the preference displays, etc., then press ENTER.
3Press 5/∞ to select the your monitor type, then
press ENTER.
•For a normal (conventional) TV, select “4:3 LB” or
“4:3 PS.” (See “MONITOR TYPE” in “Initial
settings.”)
• For a wide-screen TV, select “16:9.”
4Press 5/∞ to select a desired digital output
signal type, then press ENTER.
Set this item correctly according to your Dolby
Digital decoder, DTS decoder, or amplifier with a
built-in decoder.
(If you do not connect the player to such a device,
press ENTER to finish the setting.)
• When connecting to a Dolby Digital decoder,
select “DOLBY DIGITAL/PCM.”
• When connecting to a DTS decoder, select
“STREAM/PCM.”
• When connecting to other digital device, select
“PCM ONLY.”
To bring up the DVD PLAYER SET UP display later
Press SET UP for a few seconds until the DVD PLAYER
SET UP display appears.
4
1
2
3
Lithium coin battery
(product number: CR2032)
MENU LANGUAGE ENGLISH
AUDIO LANGUAGE ENGLISH
SUBTITLE OFF
ON SCREEN LANGUAGE ENGLISH
DVD PLAYER SET UP
ENGLISH
FRENCH
SPANISH
MONITOR TYPE 4:3 L.B.
PICTURE SOURCE AUTO
SCREEN SAVER
BACK GROUND
ON
STANDARD
DVD PLAYER SET UP
16:9
4:3 LB
4:3 PS
DIGITAL AUDIO OUTPUT DOLBY DIGITAL/PCM
ANALOG DOWN MIX DOLBY PROLOGIC
D.RANGE CONTROL ON
OUTPUT LEVEL
DVD PLAYER SET UP
PCM ONLY
DOLBY DIGITAL/PCM
STREAM/PCM
STANDARD
1 2 3 4
5 6 7 8
Basic Operations
213
546
879
010 +10
DISPLAY
/DIMMER
SOUND
EFFECT
ANGLE
THUMBNAIL
/LIST
SET UP
PREVIOUS
CLEAR
ENTER
SUB TITLE AUDIO ZOOM
TITLE
/GROUP RETURN CANCEL
STANDBY/ON
MENU
SELECT NEXT
I/P ON SCREEN
SLOW
TOP
SLIDE EFFECT
MENU
Turning on and off the player
With the label side up
Insert a disc
1Press 0 to open the disc tray.
2Place a disc in the disc tray.
• To insert an 8-cm disc, place it in the inner recess.
3Press 0 to close the disc tray.
Point toward the remote sensor
directly as possible (the operating
range is approx. 5 m.)
• Each indicator lights up when corresponding
function/mode is activated, or corresponding
information is on the main display.
Main display
About On-screen guide icons
: Playback.
: Pause.
/:Slow-motion playback with the current
speed.
/:Fast forward/backward playback with
the current speed.
: At the beginning of a scene containing
multi-angle views.
: At the beginning of a scene containing
multi-audio sounds.
: At the beginning of a scene containing
multi-subtitles.
You can change the setting so that the on-screen
guide icons do not appear on the TV screen. (See
“ON SCREEN GUIDE” in “Initial settings.”)
Basic playback
Buttons To do
3Start Playback
7Stop
•When RESUME MODE is ON
or DISC RESUME, this player
memorizes the position on
the disc where you
interrupted playback.
– To resume playback, press
3.
– To stop playback
completely, press 7 again.
8Pause*
• Each time you press the
button, the still picture
advances to the next frame.
¡/1Fast forward/backward*
(While paused)
Slow-motion playback*
• Each time you press the
button, the playback speed
changes.
¢/4Skip chapter/track
• If you press and hold the
button during playback,
playback is advanced/
reversed at 5 times normal
speed.
QUICK
PLAYBACK
(Only for DVD Video)
The disc is played back at
about 1.5 times normal speed.
The sound is not muted, and
the subtitle does not go off.
(Only for DVD Video)
The playback position moves
back 10 seconds before the
current position (only within the
same title).
* To return to normal playback, press 3.
Changing the display brightness
Press and hold DISPLAY/DIMMER to
change the brightness of the display
window. Release the button at the desired
brightness.
Changing the display window contents
Each time you press DISPLAY/DIMMER,
the display window contents changes.
Using the disc menu
You can operate a disc—DVD and
SVCD/VCD with Playback Control*
(PBC)—using the disc menu
shown on the TV screen.
* A method of controlling disc play
for SVCD/VCD by using the disc
menu.
7 For DVD
1Press TOP MENU or MENU to show the disc menu.
2Press 5/∞/2/3 to select a desired item, then press
ENTER or 3 (SELECT).
• With some discs, you can also select items by entering the
number using the numeric buttons.
7 For SVCD/VCD
1In stop mode, press TOP MENU or 3 (SELECT) to show
the menu.
2Press the numeric buttons to select a desired item.
To select 5: press 5.
To select 23: press +10, +10, then 3.
To select 40: press +10, +10, +10, then 10.
• To move to the next or previous page of the current menu,
press 4 or ¢.
• To return to the previous menu, press RETURN.
To cancel PBC
Press the numeric buttons instead of 3 (SELECT) to start
playback.
To reactivate PBC
• Press TOP MENU or MENU - THUMBNAIL/LIST.
• Press 7 to stop playback, then 3 (SELECT).
Locating the beginning of a
scene or song
You can select a title/chapter/
track directly and start playback.
For DVD Video:
(While stopped) select title.
(While playing back) select
chapter.
For SVCD/VCD/CD:
Select track.
To select 5: press 5.
To select 23: press +10, +10,
then 3.
To select 40: press +10, +10,
+10, then 10.
• If you press TITLE/GROUP
before entering the number,
you can select the title instead
of the chapter.
Turning on and off the player
Connections
Before making connections:
• Do not connect the AC power cord until all other connections have been made.
•Connect VIDEO OUT of the unit directly to the video input of your TV. Connecting VIDEO OUT of the player
to a TV via a VCR/an integrated TV/Video system may cause a monitor problem.
Basic Connection
Connecting to a TV with component jacks
When connecting your TV by the component video
cable, set the scanning mode selector as follows:
• When the TV does not support the progressive
scanning mode: \480i
• When the TV supports the progressive scanning
mode: \480p
• When you want to select the scanning mode
depending on the source condition: \REMOTE*
* To switch the scanning mode between Progressive
(480p) and Interlace (480i) by the remote control,
press and hold down VFP-I/P for a few seconds.
NOTES
• Connect “Y” to “Y,”“PB” to “PB(CB),”“PR” to “PR(CR)”
correctly.
•When using the COMPONENT jacks, do not connect
the S-VIDEO OUT jack with the player.
About the scanning mode indicator
NOTE
Some progressive TV are not fully compatible with the
unit. To check the compatibility of your TV, contact your
local JVC customer service center.
Connecting to a stereo audio amplifier (receiver)
Connecting to a digital audio device
To enjoy high-quality surround sound, connect the
DIGITAL OUT (COAXIAL) jack to a Dolby Digital or DTS
decoder or an amplifier with a built-in decoder.
NOTES
•Depending on the disc, no signal may be output from
the DIGITAL OUT. Make an analog connection in this
case.
• Set [DIGITAL AUDIO OUTPUT] in the [AUDIO]
preference display correctly according to the
connected digital audio equipment. (See “DIGITAL
AUDIO OUTPUT” in “Initial settings.”)
RIGHT
LEFT
COAXIAL
PCM/STREAM
DIGITAL OUT
AUDIO OUT
VIDEO
480i
480p
REMOTE
VIDEO OUT
COMPONENT
P
R
P
B
Y
RIGHT
LEFT
AUDIO
VIDEO
IN
S-VIDEO
S-VIDEO
Set the scanning
mode selector to
“480i.”
NOTES
• If your TV has a monaural
audio input instead of stereo,
use an optional audio cable
which converts stereo audio
output to monaural.
•The VIDEO jack, S-VIDEO OUT
jack and COMPONENT jacks
can not be used at the same
time.
Connect only the VIDEO jack,
S-VIDEO OUT jack, or
COMPONENT jacks which you
want to use.
S-video cable*
(not supplied)
Audio/video
cable*
(supplied) Red
White
TV
The unit
Yellow
[PICTURE SOURCE]
of the PICTURE menu
Source type of DVD VIDEO
Film source Video source
AUTO [DDP] [P]
FILM [DDP] [DDP]
VIDEO(NORMAL)/
(ACTIVE) [P] [P]
COMPONENT
P
R
P
B
Y
To component video input
RIGHT
LEFT
COAXIAL
PCM/STREAM
DIGITAL OUT
AUDIO OUT
To analog audio input
RIGHT
LEFT
COAXIAL
PCM/STREAM
DIGITAL OUT
AUDIO OUT
To analog audio input
To digital
audio input
Menu bar functions
You can use various functions from the menu bar.
To bring up the menu bar
When a disc is inserted, press ON SCREEN twice.
A menu bar for the type of disc inserted will appear
under the status bar.
Ex.: Menu bar for DVD VIDEO
To dismiss the menu bar, press ON SCREEN.
Basic operation procedure
1Press 2/3 to select the icon you want to work
with.
2Press ENTER.
After pressing ENTER:
(1) When a pull-down menu appears, press 5/∞ to
select the setting you want, then press ENTER.
(2) When a number-entry box appears, use the
numeric buttons to enter the number you want,
then press ENTER.
(3) When changing setting, press ENTER
repeatedly to select the setting you want.
NOTES
•The selected item on the menu bar is shown in green.
• The available functions differ depending on the unit
status. Refer to the explanation below to check when
you can use a certain function.
Menu bar functions
selects the time mode shown in the display
window and the status bar.
• TOTAL: Elapsed time of current title (DVD) or a disc
(CD/VCD/SVCD)
• T.REM: Remaining time of current title (DVD) or a
disc (CD/VCD/SVCD)
(while in stop mode, disc total time)
• TIME: Elapsed time of current chapter (DVD) or
track (CD/VCD/SVCD)
• REM: Remaining time of current chapter (DVD) or
track (CD/VCD/SVCD)
(while in stop mode, current track total time)
selects repeat mode.
DVD: During playback
CD: In any condition
VCD/SVCD: In any condition except PBC playback
• CHAPTER: Current chapter repeat (DVD)
• TITLE: Current title repeat (DVD)
• TRACK: Current track repeat (CD/VCD/SVCD)
• ALL: All track repeat (CD/VCD/SVCD)
• A-B: A-B repeat (During playback). After
selecting A-B, press ENTER at the
beginning point of repeat, then press
ENTER again at the end point.
• OFF: Repeat mode deactivated. Select this to
quit repeat mode.
specifies beginning point of a title (DVD) or a
disc (CD/VCD/SVCD) by the time.
DVD: In any condition
CD: In any condition except program or
random playback
VCD/SVCD: In any condition except PBC or program
or random playback
specifies a chapter to play back from
(DVD only).
selects the audio language (DVD), sound
track (DVD), or audio channel (VCD/SVCD) during
playback.
selects the subtitle language (DVD) or
subtitle (SVCD) during playback.
selects a desired scene angle in a multi-
angle part (DVD only).
specifies the playback order of tracks while
stopped (unavailable for DVD). You can program up to
99 tracks.
1. After selecting icon, press the numeric
buttons to specify tracks in the desired order.
•To correct the program, press 5/∞ to move to
the track to be corrected, then press CANCEL. The
track is erased and the subsequent programmed
tracks move up.
Pressing 7 clears all the programmed tracks.
2. Press 3(SELECT) to start program playback.
• During program playback, you cannot edit the
program contents.
• To exit the program mode, press ON SCREEN after
clearing the program.
activates random playback while stopped
(unavailable for DVD).
1. After selecting icon, press ENTER.
The player starts random playback.
XV-N210_A2.fm Page 1 Friday, August 20, 2004 11:53 AM
Specifications
Specifications and appearance are subject to change without prior notice.
General
Readable discs:
DVD VIDEO, DVD-R (Video format), DVD-RW (Video
format), SVCD, Video CD, Audio CD (CD-DA),
CD-R/RW (CD-DA, SVCD, Video CD, MP3 format,
JPEG, MPEG-4)
Video format:
NTSC, 480i/480p selectable
Other
Power requirements:
AC 120 V , 60 Hz
Power consumption:
10.0 W (POWER ON), 2.0 W (STANDBY mode)
Mass:
1.6 k
g
(3.6 lbs)
Dimensions (W x H x D):
435 mm x 44 mm x 201 mm (17-3/16 inch x 1-3/4
inch x 7-15/16 inch)
Video outputs
COMPONENT (pin jacks)
Y Output:
1.0 Vp-p (75
Ω
)
P
B
/P
R
Output:
0.7 Vp-p (75
Ω
)
VIDEO OUT (pin jack):
1.0 Vp-p (75
Ω
)
S-VIDEO OUT (S jack)
Y Output:
1.0 Vp-p (75
Ω
)
C Output:
286 mVp-p (75
Ω
)
Horizontal resolution:
500 lines or more
Audio outputs
ANALOG OUT (pin jack):
2.0 Vrms (10 k
Ω
)
DIGITAL OUT (COAXIAL):
0.5 Vp-p (75
Ω
termination)
Audio characteristics
Frequency response
CD (sampling frequency 44.1 kHz):
2 Hz to 20 kHz
DVD (sampling frequency 48 kHz):
2 Hz to 22 kHz(4 Hz to 20 kHz for DTS and Dolby
Digital bitstream signals)
DVD (sampling frequency 96 kHz):
2 Hz to 44 kHz
Dynamic range
16 bit:
More than 98 dB
20 bit/24 bit:
More than 100 dB
Wow and flutter:
Unmeasurable (less than ± 0.002%)
Total harmonic distortion:
less than 0.009%
* Notes for PX model (Check the specification
indication on the rear panel.)
Power requirements:
AC
110 V to 240 V , 50 Hz/60 Hz
Power consumption:
11.0 W (POWER ON),
2.0 W (STANDBY mode)
BT-51005-5
(0301)
QUALITY SERVICE
HOW TO LOCATE YOUR JVC SERVICE CENTER
Dear Customer,
In order to receive the most satisfaction from your purchase,please read the instruction booklet before
operating the unit.In the event that repairs are necessary, please call 1 (800)537-5722 for your nearest
authorized servicer or visit our website at www.JVC.com
Remember to retain your Bill of Sale for Warranty Service.
Do not service the television yourself
Caution
To prevent electrical shock,do not open the cabinet.There are no user serviceable
parts inside.Please refer to qualified service personnel for repairs.
Accessories
To purchase accessories for your JVC product,please call toll free:1 (800)882-2345 or
on the web at www.JVC.com
TOLL FREE: 1 (800) 537-5722
http://www.jvc.com
Authorized Service Centers
®
Country/Area code list for Parental Lock
AD Andorra
AE United Arab Emirates
AF Afghanistan
AG Antigua and Barbuda
AI Anguilla
AL Albania
AM Armenia
AN Netherlands Antilles
AO Angola
AQ Antarctica
AR Argentina
AS American Samoa
AT Austria
AU Australia
AW Aruba
AZ Azerbaijan
BA Bosnia and
Herzegovina
BB Barbados
BD Bangladesh
BE Belgium
BF Burkina Faso
BG Bulgaria
BH Bahrain
BI Burundi
BJ Benin
BM Bermuda
BN Brunei Darussalam
BO Bolivia
BR Brazil
BS Bahamas
BT Bhutan
BV Bouvet Island
BW Botswana
BY Belarus
BZ Belize
CA Canada
CC Cocos (Keeling)
Islands
CF Central African
Republic
CG Congo
CH Switzerland
CI Côte d’Ivoire
CK Cook Islands
CL Chile
CM Cameroon
CN China
CO Colombia
CR Costa Rica
CU Cuba
CV Cape Verde
CX Christmas Island
CY Cyprus
CZ Czech Republic
DE Germany
DJ Djibouti
DK Denmark
DM Dominica
DO Dominican Republic
DZ Algeria
EC Ecuador
EE Estonia
EG Egypt
EH Western Sahara
ER Eritrea
ES Spain
ET Ethiopia
FI Finland
FJ Fiji
FK Falkland Islands
FM Micronesia (Federated
States of)
FO Faroe Islands
FR France
FX France, Metropolitan
GA Gabon
GB United Kingdom
GD Grenada
GE Georgia
GF French Guiana
GH Ghana
GI Gibraltar
GL Greenland
GM Gambia
GN Guinea
GP Guadeloupe
GQ Equatorial Guin ea
GR Greece
GS South Georgia and
theSouth Sandwich
GT Guatemala
GU Guam
GW Guinea-Bissau
GY Guyana
HK Hong Kong
HM Heard Island and
McDonald Islands
HN Honduras
HR Croatia
HT Haiti
HU Hungary
ID Indonesia
IE Ireland
IL Israel
IN India
IO British Indian Ocean
Territory
IQ Iraq
IR Iran (Islamic Republic
of)
IS Iceland
IT Italy
JM Jamaica
JO Jordan
JP Japan
KE Kenya
KG Kyrgyzstan
KH Cambodia
KI Kiribati
KM Comoros
KN Saint Kitts and Nevis
KP Korea, Democratic
People’s Republic of
KR Korea, Republic of
KW Kuwait
KY Cayman Islands
KZ Kazakhstan
LA Lao People’s
Democratic Republic
LB Lebanon
LC Saint Lucia
LI Liechtenstein
LK Sri Lanka
LR Liberia
LS Lesotho
LT Lithuania
LU Luxembourg
LV Latvia
LY Libyan Arab
Jamahiriya
MA Morocco
MC Monaco
MD Moldova, Republic of
MG Madagascar
MH Marshall Islands
ML Mali
MM Myanmar
MN Mongolia
MO Macau
MP Northern Mariana
Islands
MQ Martinique
MR Mauritania
MS Montserrat
MT Malta
MU Mauritius
MV Maldives
MW Malawi
MX Mexico
MY Malaysia
MZ Mozambique
NA Namibia
NC New Caledonia
NE Niger
NF Norfolk Island
NG Nigeria
NI Nicaragua
NL Netherlands
NO Norway
NP Nepal
NR Nauru
NU Niue
NZ New Zealand
OM Oman
PA Panama
PE Peru
PF French Polynesia
PG Papua New Guinea
PH Philippines
PK Pakistan
PL Poland
PM Saint Pierre and
Miquelon
PN Pitcairn
PR Puerto Rico
PT Portugal
PW Palau
PY Paraguay
QA Qatar
RE Réunion
RO Romania
RU Russian Federation
RW Rwanda
SA Saudi Arabia
SB Solomon Islands
SC Seychelles
SD Sudan
SE Sweden
SG Singapore
SH Saint Helena
SI Slovenia
SJ Svalbard and Jan
Mayen
SK Slovakia
SL Sierra Leone
SM San Marino
SN Senegal
SO Somalia
SR Suriname
ST Sao Tome and
Principe
SV El Salvador
SY Syrian Arab Republic
SZ Swaziland
TC Turks and Caicos
Islands
TD Chad
TF French Southern
Territories
TG Togo
TH Thailand
TJ Tajikistan
TK Tokelau
TM Turkmenistan
TN Tunisia
TO Tonga
TP East Timor
TR Turkey
TT Trinidad and Tobago
TV Tuvalu
TW Taiwan
TZ Tanzania, United
Republic of
UA Ukraine
UG Uganda
UM United States Minor
Outlying Islands
US United States
UY Uruguay
UZ Uzbekistan
VA Vatican City State
(Holy See)
VC Saint Vincent and the
Grenadines
VE Venezuela
VG Virgin Islands (British)
VI Virgin Islands (U.S.)
VN Vietnam
VU Vanuatu
WF Wallis and Futuna
Islands
WS Samoa
YE Yemen
YT Mayotte
YU Yugoslavia
ZA South Africa
ZM Zambia
ZR Zaire
ZW Zimbbabwe
Audio/Video files playback
You can play back MP3/JPEG/MPEG4 (simple profile/asf file) files on a CD/CD-R/RW.
Precautions
• Use “ISO 9660” as the disc format.
• The player does not support “packet writing (UDF
files)” discs.
• The player supports discs recorded with up to five
multiple sessions.
•The player may be unable to play back a disc due to
the characteristics or recording conditions.
•The player recognizes up to the fifth layer of groups,
999 files per group (including unplayable files), and
up to 250 groups per disc.
• Add the appropriate extension (“.mp3”, “.jpg”, and
“.asf”) to the file name.
• MP3i and MP3 Pro are not available.
• The player cannot play back a picture of more than
5120 x 3413 pixels (baseline JPEG) or 2048 x 1536
pixels (progressive JPEG).
Selecting a specific file or group
You can select files or folders (groups) using the
Control display on the TV screen.
Control display
Press 5
/∞
/2
/3
to move the cursor bar to a desired
file, then press 3
(SELECT).
• When you press ENTER, only the selected file is
played back.
Various playback mode
• To play back a disc continuously, select NORMAL.
Repeat playback
1. While stopped, press 5
/∞
/2
/3
to move the cursor
bar to playback mode.
2. Press ENTER repeatedly to select the desired repeat
mode.
• REPEAT 1: Repeats the current file.
• REPEAT GROUP: Repeats all files in the current
group.
• REPEAT ALL: Repeats all files on the disc.
3. Press 3
to move the cursor bar to the file column,
then press 3
(SELECT).
Random playback
1. While stopped, press 5
/∞
/2
/3
to move the cursor
bar to playback mode.
2. Press ENTER repeatedly to select RANDOM.
3. Press 3
to move the cursor bar to the file column,
then press 3
(SELECT).
Program playback
1. While stopped, press 5
/∞
/2
/3
to move the cursor
bar to playback mode.
2. Press ENTER repeatedly to select PROGRAM.
3. Press 5
/∞
/2
/3
to select the desired file, then press
ENTER.
4. Repeat step 3 until all the desired files are selected.
• To erase the last programmed file, press 2
to
move the cursor bar to the programmed files
column, then press CANCEL.
5. Press 3
(SELECT).
NORMAL GROUP
MP3
MPEG4
SLIDESHOW
MIX
--
MOVIE01.asf
MOVIE02.asf
PICT01.jpg
PICT02.jpg
PICT03.jpg
MUSIC01.mp3
MUSIC02.mp3
DISC CONTROL
Select these
sections to show the
upper layer.
Current file
File columnGroup column
Current group
Current playback mode
Various JPEG files playback
To zoom in a picture
Press ZOOM.
Each time you press ZOOM, you can magnify a JPEG
file (x1.5/x2/x4).
• You can also magnify an MPEG-4 file (x2/x4).
To rotate/reflect a still picture
While a still picture is played back:
• Pressing 2
/3
rotates the picture by 90
°
.
• Pressing 5
reflects the picture vertically.
• Pressing ∞
reflects the picture horizontally.
To select a JPEG files from the thumbnail list
1. Press and hold MENU-THUMBNAIL/LIST while a
JPEG file is selected on the Control display.
2. Press 5
/∞
/2
/3
to select the desired picture, then
press ENTER.
• You can change the page of thumbnail list by
pressing 4
/¢
.
Slide show playback of JPEG files
Press 3
(SELECT) while a JPEG file is selected on the
Control display.
• To select slide show effect
Press and hold ANGLE-SLIDE EFFECT until
[SLIDE EFFECT MODE:] and the current mode
appears on the TV screen.
By pressing and holding the button repeatedly, you
can select the effect out of 11 effects, random effect
selection (RAND), and no effect (NONE).
The effect is not applied to progressive JPEG files.
Initial settings
You can change the settings of this player according to
your preferences and playing environment.
How to set the Initial settings
1
Press SET UP.
2
Press 2
/3
to select the menu.
3
Press 5
/∞
to move to select the item.
4
Press ENTER.
5
Press 5
/∞
to select the options, then press
ENTER.
To dismiss a preference display
Press SET UP.
NOTES
•Some items in the menus cannot be changed during
playback.
•While CD-R/RW which contains MP3/MPEG-4 files is
inserted, you cannot show the menus.
• If the upper and lower parts of the menu are cut off,
adjust the picture size control of the TV.
• For settings of the LANGUAGE menu or the
PARENTAL LOCK menu, see also “Language
codes” below.
• Depending on the disc, the settings may not apply
correctly.
MENU LANGUAGE ENGLISH
AUDIO LANGUAGE ENGLISH
SUBTITLE OFF
ON SCREEN LANGUAGE ENGLISH
LANGUAGE
Item Contents
MENU LANGUAGE
You can select the default menu language of DVD VIDEO.
AUDIO LANGUAGE
You can select the default audio language of DVD VIDEO.
SUBTITLE
You can select the default subtitle language of DVD VIDEO.
ON SCREEN LANGUAGE
You can select “ENGLISH,” “FRENCH,” or “SPANISH” as the on-screen language.
LANGUAGE menu
PICTURE menu
Item Contents
MONITOR TYPE
You can select the monitor type to match your TV when you play back DVD VIDEO
discs recorded for wide-screen televisions.
[16:9] (Wide television screen):
For a wide-screen (16:9) TV.
[4:3 LB] (Letter Box conversion):
For a normal (4:3) TV. Displays a wide-screen
picture to fit the width of the TV screen keeping the aspect ratio.
[4:3 PS] (Pan Scan conversion):
For a normal (4:3) TV. The picture is zoomed
up to filling the screen vertically and the left and right sides of the picture are
cut off.
PICTURE SOURCE
You can obtain optimal picture quality by selecting the source type of the disc
contents.
[AUTO]:
Normally, select this option. The player recognizes the picture type (film
or video source) of the current disc according to the disc information.
[FILM]:
For a film source disc.
[VIDEO(NORMAL)]:
For a video source disc with relatively a few movements.
[VIDEO(ACTIVE)]:
For a video source disc with relatively a lot of movements.
SCREEN SAVER
You can set the screen saver function to ON or OFF.
BACKGROUND
You can use your favorite image as the opening display.
[STANDARD]:
Display the JVC original image.
[USER]:
Display your favorite image as the opening display when a JPEG image
is registered.
[SAVE AS BACKGROUND]:
To register a new image, select this while a JPEG
image is displayed on the TV.
16:9 4:3 LB
4:3 PS
Language codes list for the LANGUAGE menu
AA
Afar
AB
Abkhazian
AF
Afrikaans
AM
Ameharic
AR
Arabic
AS
Assamese
AY
Aymara
AZ
Azerbaijani
BA
Bashkir
BE
Byelorussian
BG
Bulgarian
BH
Bihari
BI
Bislama
BN
Bengali,Ban
gla
BO
Tibetan
BR
Breton
CA
Catalan
CO
Corsican
CS
Czech
CY
Welsh
DA
Danish
DZ
Bhutani
EL
Greek
EO
Esperanto
ET
Estonian
EU
Basque
FA
Persian
FI
Finnish
FJ
Fiji
FO
Faroese
FY
Frisian
GA
Irish
GD
Scots Gaelic
GL
Galician
GN
Guarani
GU
Gujarati
HA
Hausa
HI
Hindi
HR
Croatian
HU
Hungarian
HY
Armenian
IA
Interlingua
IE
Interlingue
IK
Inupiak
IN
Indonesian
IS
Icelandic
IW
Hebrew
JI
Yiddish
JW
Javanese
KA
Georgian
KK
Kazakh
KL
Greenlandic
KM
Cambodian
KN
Kannada
KO
Korean
(KOR)
KS
Kashmiri
KU
Kurdish
KY
Kirghiz
LA
Latin
LN
Lingala
LO
Laothian
LT
Lithuanian
LV
Latvian,
Lettish
MG
Malagasy
MI
Maori
MK
Macedonian
ML
Malayalam
MN
Mongolian
MO
Moldavian
MR
Marathi
MS
Malay (MAY)
MT
Maltese
MY
Burmese
NA
Nauru
NE
Nepali
NL
Dutch
NO
Norwegian
OC
Occitan
OM
(Afan)
Oromo
OR
Oriya
PA
Panjabi
PL
Polish
PS
Pashto,
Pushto
PT
Portuguese
QU
Quechua
RM
Rhaeto-
Romance
RN
Kirundi
RO
Rumanian
RU
Russian
RW
Kinyarwanda
SA
Sanskrit
SD
Sindhi
SG
Sangho
SH
Serbo-
Croatian
SI
Singhalese
SK
Slovak
SL
Slovenian
SM
Samoan
SN
Shona
SO
Somali
SQ
Albanian
SR
Serbian
SS
Siswati
ST
Sesotho
SU
Sundanese
SV
Swedish
SW
Swahili
TA
Tamil
TE
Telugu
TG
Tajik
TH
Thai
TI
Tigrinya
TK
Turkmen
TL
Tagalog
TN
Setswana
TO
Tongan
TR
Turkish
TS
Tsonga
TT
Tatar
TW
Twi
UK
Ukrainian
UR
Urdu
UZ
Uzbek
VI
Vietnamese
VO
Volapuk
WO
Wolof
XH
Xhosa
YO
Yoruba
ZU
Zulu
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND
IN COMMONWEALTH OF PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner.
Such repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service
centers. Parts used for replacement are warranted only for the remainder of the Warranty Period. All products and parts
thereof may be brought to a JVC authorized service center on a carry-in basis except for Television sets having a screen
size 25 inches and above which are covered on an in-home basis.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized
service center, please call toll free: (800) 537-5722.
If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with
a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the
name and location of which will be given to you by the toll-free number.
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty
installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by
JVC to render such service, or if affixed to any attachment not provided with the products, or if the model number
or serial number has been altered, tampered with, defaced or removed;
2. Initial installation and installation and removal for repair;
3. Operational adjustments covered in the Owner's Manual, normal maintenance, video and audio head cleaning;
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;
5. Signal reception problems and failures due to line power surge;
6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;
7. Accessories;
8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);
There are no express warranties except as listed above.
THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS
LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER
DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE
TO TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH
OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANT-
ABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an
implied warranty lasts, so these limitations or exclusions may not apply to you. This warranty gives you specific
legal rights and you may also have other rights which vary from state to state.
LIMITED WARRANTY
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE
ORIGINAL PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date
of original retail purchase for the period as shown below. ("The Warranty Period")
PARTS LABOR
1 YR 90
DAYS
JVC COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
1700 Valley Road
Wayne, NJ 07470
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OF
REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION
PACKAGED WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. which is located either on the rear, bottom or side of the cabinet. Retain this information
for future reference.
Model No. : Serial No. :
Purchase data : Name of dealer :
CONSUMER VIDEO 1-90
Item Contents
DIGITAL AUDIO OUTPUT
Set this item correctly when connecting to an external device equipped with a
digital input.
[PCM ONLY]:
When connecting to audio equipment which can decode only linear
PCM signals.
[DOLBY DIGITAL/PCM]:
When connecting to a Dolby Digital decoder or an
amplifier with a built-in Dolby Digital decoder.
[STREAM/PCM]:
When connecting to an amplifier with a built-in DTS, MPEG
Multichannel or Dolby Digital decoder.
ANALOG DOWN MIX
Set this item properly according to your analog audio connection to play the sound of
the surround multichannel audio on a DVD VIDEO.
[DOLBY SURROUND]:
Select this when connecting to a surround decoder.
[STEREO]:
Select this when connecting to a stereo amplifier or TV, or in case you
want to record from a DVD VIDEO to a MiniDisc, cassette, etc.
D.RANGE CONTROL
Set this item to listen to DVD VIDEO recorded in Dolby Digital format at low or middle
volume.
[WIDE RANGE]:
You can enjoy powerful playback sound.
[NORMAL]:
Normally, select this.
[TV MODE]:
Select this if the sound level of DVD VIDEO is lower than the one of TV
program to make the sound at a lower volume clear.
OUTPUT LEVEL
Set this item to attenuate the level of the signal output from the analog AUDIO OUT
terminals. If the sound from the speaker is distorted, select [LOW].
Item Contents
RESUME
You can select the resume playback mode.
[ON]:
The player resumes playback from the position where playback has been
stopped if the disc is still in the disc tray.
[OFF]:
This function is deactivated.
[DISC RESUME]:
The player resumes playback of the last 30 discs played. The
player retains a memory of the stopped position of each disc even if the disc is
removed from the disc tray.
ON SCREEN GUIDE
Activate or deactivate the on-screen guide.
AUTO STANDBY
Set the time until the player turns off (into standby) automatically if playback is
stopped for more than 30 minutes or 60 minutes.
PARENTAL LOCK
Select this item, then press ENTER to show the PARENTAL LOCK menu for
limiting playback by children. Scenes which are limited by this function are not
played or replaced with other scenes.
[COUNTRY CODE]:
Select the code of your country/area.
[SET LEVEL]:
Select the level of restriction. (“1” is the strictest.)
[PASSWORD]:
Enter your password by pressing the numeric buttons (0 to 9).
[EXIT]:
Select this and press ENTER to go back to the OTHERS menu.
Note:
•Some DVD VIDEO cannot be played by this function. If you try to play such a disc,
the PARENTAL LOCK menu appears on the TV and asks whether you want to
release the lock or not.
To release the lock and play, select “TEMPORARY RELEASE,” press ENTER, then
enter your password. Otherwise, eject the disc.
• To change the setting of the limitation, you need to enter your password.
• If you forget your pass word, enter “8888.”
AUDIO menu
OTHERS menu
SET LEVEL NONE
PASSWORD _ _ _ _
PARENTAL LOCK
EXIT
COUNTRY CODE US
8
1211109
13 14 15 16
Troubleshooting
Power
Power does not come on.
\
Power plug is not inserted securely. Plug in
securely.
Operation
“REGION CODE ERROR!” is shown on the TV.
\
Region code of the inserted disc does not match the
player. Check the region code of the disc printed on
the disc jacket.
Operation is not possible.
\
Microcomputer malfunction due to lightning or static
electricity. Turn off the power and unplug the power
cord, then connect the power cord again.
\
Moisture condensation caused by a sudden change
of temperature or humidity. Turn off the power, then
turn it on a few hours later.
\
The disc does not allow the operation, or an
unplayable disc is inserted. Check and replace the
disc.
[LOCK] is displayed on the display window
and the disc tray does not open.
\
When you press 0
while pressing down 7
on the
player in standby mode, the tray lock function is
activated. The disc tray cannot be opened or closed
in this status. To release this status, press 0
while
pressing down 7
on the player in standby mode.
Picture
Picture is noisy.
\
The player is connected to a VCR directly and the
copyguard function is activated. Connect the player
so that the picture signal flows directly to the TV.
With some discs, the picture may be blurred when
[PICTURE SOURCE] is set to [FILM] or [AUTO].
Set [PICTURE SOURCE] to [VIDEO (NORMAL)] or
[VIDEO (ACTIVE)].
Picture is distorted when using
COMPONENT or S-VIDEO OUT jack(s).
\
Both the component connection and S-video
connection are made. Disconnect the unused one.
No picture is displayed on the TV screen or
the screen is blurred or divided into two parts.
\
The player is in the progressive scanning mode
though it is connected to a TV via the VIDEO or
S-VIDEO OUT jack. Observe the display window. If
[P] is turned on, the player is in the progressive
scanning mode.
Set the VIDEO SIGNAL SELECTOR on the rear
panel to “480i,” or set it to “REMOTE” and make the
Progressive scanning mode inactive by using the
VFP - I/P button.
Audio
DVD VIDEO disc playback sound level is
lower than TV broadcast sound level.
\
Set the [D.RANGE CONTROL] preference to [TV
MODE].
Analog audio output is distorted.
\
Set the [OUTPUT LEVEL] preference to [LOW].
MP3/JPEG/MPEG-4
No sound and/or no picture comes out.
\
MP3/MPEG-4 disc is recorded with the “packet
writing (UDF file).” It cannot be played.
Check the files you want to play back.
Files (tracks) are not played in the recorded
order.
\
This player plays the files in the alphabetic order.
So, the playback order can vary.
MPEG-4 files cannot be played back.
\
The format of the file is not asf.
XV-N210_A2.fm Page 2 Friday, August 20, 2004 11:53 AM
