Jack Lalannes Power Juicer Classic Operating Manual PJ NEWest Instructions

2015-05-12

: Jack-Lalannes-Power-Juicer Jack-Lalannes-Power-Juicer-Power-Juicer-Classic-Operating-Manual-715988 jack-lalannes-power-juicer-power-juicer-classic-operating-manual-715988 jack-lalannes-power-juicer pdf

Open the PDF directly: View PDF .
Page Count: 7

OPERATING MANUAL

IMPORTANT SAFEGUARDS

READ THESE SAFEGUARDS CAREFULLY

BEFORE USING THIS PRODUCT!

When using electrical appliances, basic safety precautions should always

be followed including the following:

•NOT FOR USE BY CHILDREN! Keep out of the reach of children to avoid injury.

This appliance is not a toy.

•Consult your physician before giving fresh juice to children, especially infants.

•Be sure to turn to OFF position after each use of your juicer

•Make sure the lid is attached properly and securely locked before operating

the Power Juicer.

•Do not unfasten the locking bar during operation.

•To avoid risk of injury keep hands and utensils out of the juicer and away from its sharp

blade during operation.

•Use the pusher, not fingers or utensils, to propel the food into the juicer.

•Should food become lodged in the opening use pusher to push it down. If food remains

stuck, turnthe power off, wait until motor stops, unit shuts down completely,and is

unplugged before disassembling the juicer and removing the blocked food.

•Make sure the motor stops completely and the unit is unplugged from the electrical

outlet before cleaning, putting on or removing parts.

•Toprotect against risk of electrical shock or injury, never immerse power cord,

plug, or main unit in water, or other liquids.

•If juicer stops due to improper operation or if there is excessive noise, turn power off,

wait for blade to stop spinning, unplug from electrical outlet, disassemble and clean

all components then reassemble machine.

•Do not use outdoors.

•Do not operate this or any appliance with a damaged cord or plug.

•Do not operate if appliance malfunctions, is dropped or damaged in any manner.

Let a qualified appliance repair person examine and or repair appliance before using.

•Toavoid electric shock or serious injurydo not use any attachments that were

not recommended or sold by the manufacturer.

•Do not let power cord hang over the edge of table, counter, or let cord touch

hot surfaces such as stoves.

•Toreduce the risk of injury, never place blade on base without properly

assembling the unit.

•This appliance has a polarized plug (one blade is wider than the other). To reduce

the risk of electric shock, this plug will fit in a polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified

electrician. Do not modify or force the plug in any way.

•The motor will not run if unit is not properly assembled. The motor has a built-in safety

featurethat will not let the power turnon unless the locking bar is locked in place.

SAVE THESE INSTRUCTIONS

TABLE OF CONTENTS

Important Safety Information

Helpful Hints

Parts List

Assembly

Disassembly

Cleaning Your Power Juicer

Troubleshooting

Lip

Pulp Guard

Chute

Locking Bar

HELPFUL HINTS

Obtain the best results from your Jack LaLanne Power Juicer

by following these helpful hints.

• Do not put any fruit or vegetables in your machine until power is turned on.

• Allow unit to run for at least 10 seconds before juicing.

• Do not force food into the juicer. Allow food to pass through slowly and steadily using

the pusher. You do not need to apply pressure unless the juicer starts to vibrate. Then

only a slightly harder push should bring it back to balance.

• Any fruit or vegetable that will fit the chute can be put through whole. The only time it is

necessary to cut is when something is too large. Then it should be cut into large enough

pieces to fit in the chute. Do not cut pieces too small.

• Remove large pits such as peach, mango, etc. as they will damage the blade and possibly

the unit. Before juicing cherries we recommend you remove the pits using a cherry pitter.

• Cleaning can be made easy by placing a plastic bag inside the pulp collector container.

When you are done juicing, the bag can be lifted out and disposed of easily leaving the

pulp collector easier to clean.

• Let the Power Juicer run for a few minutes before turning off to allow any excess juice to

be extracted from the pulp. Once turned off it is quite normal for the juicer to spin for a

minute or so due to the very fine precision balancing of this appliance. Wait until it is

done spinning before disassembling.

• Do not use bananas or avocados as they do not contain juice and will clog machine. Add

them separately in a blender.

• We do not recommend using overripe fruit as it will leave too much pulp in the filter and

clog the machine.

• Do not pour liquids into the machine at any time.

Pusher

Filter

Blade

Crescent Tool

(for tightening and removing blade)

MAIN UNIT

(Fully Assembled)

Receptacle

Juice Spout

Screw Peg

Base

Pulp

Collector

PARTS LIST

(Crescent tool pegs fit here to tighten.

WARNING: DO NOT OVER TIGHTEN)

(Pegs fit into blade.)

Lid with Built-in Pulp Guard

SAVE THESE INSTRUCTIONS

ADDITIONAL SAFEGUARDS

The Power Juicer has a thermal cut-off safety feature. If the unit accidentally overheats, it will

stop working temporarily until the Power Juicer cools down. Afterwards, the unit will continue to

work again normally.

In the event the Power Juicer is jammed the motor may shut down. If this occurs the juicer should

be shut off and unplugged. The unit should be thoroughly cleaned to remove the obstruction.

The thermal cut-off safety feature is designed to shut off the motor when it over heats.

Please use extreme caution when handling the Power Juicer blade as the blades are very sharp.

Always turn power off to the Power Juicer immediately and remove power cord from electrical

outlet before disassembling to clean due to any food obstruction.

CAUTION

Use caution when handling blade as blades are very sharp.

If juicer jams turn power off immediately and remove power cord from electrical outlet before

disassembling to clean.

The Power Juicer has a thermal cut-off safety feature. If the unit accidentally overheats, it will stop

working temporarily until the Power Juicer cools down. Clear any obstruction. Afterwards, the unit

will continue to work again normally.

Receptacle

Juice Spout

Chute

Lid with built-in

Pulp Guard

Pusher

Receptacle

Lid with built-in

Pulp guard

Blade

Base

Lip

Base

Front of

Machine

(Spout side)

Filter

Receptacle

ASSEMBLY ASSEMBLY(CONT.)

STEP 2:

Place receptacle on the base,

with juicer spout facing direction

of locking bar. Settle receptacle

into alignment.

STEP 3:

Place filter inside receptacle,

matching the opening on

its bottom to the screw peg

connected to the base.

STEP 4:

Place blade inside filter, centered

over screw peg. Using orange

crescent tool, place its pegs

into the holes in the blade

and turn clockwise

until tightened.

IMPORTANT: Do not

over tighten as the

screw peg will break.

Remove crescent tool

and set aside.

CAUTION: Do not

leave tool inside juicer.

STEP 5:

Place lid with built-in pulp guard attached

on top of receptacle, making certain it is

snugly aligned with the pulp guard facing

in the opposite direction of the juice spout.

Lock lid into place by lifting locking bar

up until it clicks into grooves located

on both sides of the lid. Make sure

locking bar is in the full upright,

locked position.

IMPORTANT: The unit will not start

until this bar is properly locked in place.

STEP 6:

Insert pusher into chute.

Always use pusher to feed fruits

and vegetables into unit. Push gently,

never force. The blade will do the work.

STEP 1:

Place base on a dry flat surface with

locking bar in down position as shown.

In front of the machine (spout side).

Assemble as shown

Locking

Bar

Filter

Pulp

Collector

Crescent

Tool

Blade

Holes

Blade

Lid with Built-in

Pulp Guard

Base

Receptacle

Locking Bar

Filter

DISASSEMBLY DISASSEMBLY (CONT.)

IMPORTANT: Before disassembling the unit make sure you turn the power OFF

and unplug the machine from the electrical outlet.

STEP 2:

Lower the locking bar (silver) into

position as shown.

STEP 3:

Remove lid with pulp guard,

and pulp collector.

STEP 1:

Remove pusher from the chute.

STEP 5:

Remove filter.

STEP 6:

Remove receptacle from base.

STEP 4:

Use the crescent tool (orange) to

remove the blade. Place the two pegs

at either end of the crescent tool into

the two holes on the blade, press

down and turn counter-clockwise

to unlock the blade. Remove

blade carefully.

CLEANING YOUR

POWER JUICER

• Turn off the power switch and wait until the motor completely stops.

• With dry hands, unplug the power cord from electrical outlet.

• Disassemble the machine. (See disassembly instructions.)

• Wipe base with a soft damp cloth or sponge. Do not submerge base in water.

Do not spray with water or any other liquid. Base is not dishwasher safe.

• We recommend washing the pusher by hand in warm soapy water. Due to

temperature differences in dishwashers if you choose to wash the pusher in the

dishwasher, place it on top rack only.

• Clean all other parts in warm, soapy water. A mild detergent is recommended.

Rinse well and dry thoroughly. All components are dishwasher safe with the

exception of the base. Do not use in European Import or a commercial dishwasher.

• To clean the filter and blade, hold them under warm running water. Use a soft-

bristled dish washing brush gently to completely clean pulp from filter. Rinse

the filter from the outside under running water.

• Dry components thoroughly then assemble the machine and turn the power

on to spin out any excess water.

• Make sure unit and parts are completely dry then store in a cool, dry place.

Pusher

Pulp

Collector

Crescent Tool

Pulp Guard

The motor does not

run after being

switched on.

The motor is running

with loud noise and

shaking.

The motor overheats

causing the power to

automatically shut off.

Juice splashes from the

rim of the receptacle.

•Check to see if unit is plugged in.

•Locking bar is not locked in place properly.

•Check if all parts are assembled properly.

•Check if there is any residue left between

blade and receptacle.

•Check to see if food is stuck to the bottom of

the pusher.

•Check that all parts are assembled properly

and in the correct position.

•Juicing overripe fruit may result in too much

pulp and will clog the filter. Turn machine off

and clean the filter.

•The motor needs to warm up for 10 seconds

before use.

•The fruits and vegetables may be soft

or overripe.

•There may be too much pulp in the filter.

Turn machine off and clean the filter.

•Motor stops running due to the built-in

feature, the overheat safety control.

•This is normal.

TROUBLESHOOTING

Problem Possible Reasons and Solution

The motor is running.

The spout is in the

downward position,

but no juice is coming

out.

•Turn the power off and unplug the machine.

Wait for blade to stop spinning. Use a

toothpick to loosen any obstruction in the

non-drip spout.

Exciting Offers from

Power Juicer

Accessory Kit

& Cookbook

YES! Please Send Me the following Items:

nnOne Accessory Kit & Cookbook for only $19.99

plus $6.99 s&h. Total $26.98.

nn“Recipes for Healthy Living” Cookbook - FREE

plus $7.99 s&h. Total $7.99.

nnReplacement Parts Kit #1 for only $29.99

plus FREE s&h. Total $29.99.

nnReplacement Parts Kit #2 for only $34.99

plus FREE s&h. Total $34.99.

nnVISA nnMasterCard nnDiscover Exp. Date____

Credit Card #______________________________________

nnCheck nnMoney Order (NJ residents add 7% sales tax. PA &

CT residents add 6% sales tax. NY & NV add applicable sales tax.)

U.S. CURRENCY ONLY PRICES SUBJECT TO CHANGE

Print Name ________________________________________________

Address____________________________________________________

______________________________________________Apt._________

City______________________________________________________

State___________________ Zip_______________________________

Phone# (____________) _____________________________________

E-mail ____________________________________________________

Mail Payment Today To: POWER JUICER

26 Barnes Industrial Rd. North, P.O. Box 3125, Dept. PJ999, Wallingford, CT 06494

Please allow 4-6 weeks for shipping.

Crescent

Tool

Filter

Blade

Pulp

Collector

Pulp Guard

Pusher

Replacement

Parts Kit #1

Replacement

Parts Kit #2

Jack LaLanne’s Recipes for

Healthy Living Cookbook

Power Juicer Platform

Measuring Cup

Overflow Platform

Filter Brush

or call 1-800-526-2518 — 8:00am–9:00pm EST Monday–Friday 9:00am–5:00pm EST Saturday & Sunday

Please make checks payable to: POWER JUICER

To order or for more information on juicing visit:

www.powerjuicer.com

PJ Classic V4 0508

Distributed by:

Tristar Products, Inc.

Wallingford, CT 06494

Jack Lalannes Power Juicer Classic Operating Manual PJ NEWest Instructions

Navigation menu

Versions of this User Manual:

Views

Navigation