Japan Radio Co NKE1066 MARINE RADAR User Manual 2

Download:
Mirror Download [FCC.gov]
Document ID	2183898
Application ID	hkPa1o7VIs0J4723c479DQ==
Document Description	User Manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	373.45kB (4668140 bits)
Date Submitted	2014-02-05 00:00:00
Date Available	2014-02-05 00:00:00
Creation Date	2014-01-06 13:50:58
Producing Software	GPL Ghostscript 9.07; modified using iTextSharp™ 5.4.2 ©2000-2012 1T3XT BVBA (AGPL-version)
Document Lastmod	2014-01-06 13:51:25
Document Title	User Manual 2
Document Creator	CubePDF

Chapter 2 START THE BASIC OPERATION
Chapter 2 START THE BASIC OPERATION
When * basic adjustment is made by the serviceman etc. beforehand, please perform as it is.
(In case of no adjustment is done by the serviceman etc. beforehand, please through eyes to Chapter
5 for the time being, and after getting to know the outline of operation of this radar, perform Initial
setting of Chapter 7.)
The screen is a touch screen and can be operated by tracing a screen by a finger flip or touching.
The term of operation:
TAP: Push a screen display position once by a fingertip.
Flick: Rub a screen display position by a fingertip.
(A state recognized according to the rubbed direction)
Swipe: Rub a screen display position keeping on touch by a fingertip.
Long tap: Pushing a screen display position, continued more than
3 seconds or more by a fingertip.
The operation of a Rotary knob:
Click: Push in a Rotary knob once.
Rotating and choosing the state of a screen, then click and fix.
General using : The touch panel function is select absolute positions on panel,
on the other hands, Rotary knob select sequential data up and down.
and, at selection data appeared then click and fix.
Only Cross cursor is individual moving, no relation to another.
29
Chapter 2 START THE BASIC OPERATION
Power on startup screen.
Push PWR/CLR button.
Startup screen.
(3 Startup screen possible to select.)
Swipe on the screen for select the startup screen.
30
Chapter 2 START THE BASIC OPERATION
Rotary knob.
Push Rotary knob and rotate to select the starting item..
Select the icon you needed
by turning the knob
Tap
icon at bottm side, then full icons can be seen.
Full icons
will be appeared.
Keep press and rotate the rotary knob, then screen brillance menu will be open.
The turn while pressing
Brillance menu
will be appeared.
Rotate Rotary knob at suitanble brilliande level.
Release Rotary knob, then the brillance level is fixed
31
Chapter 2 START THE BASIC OPERATION
Sleep Cursor
Tap
Sleep TX/STBY
Tap TX/STBY
Tap TX/STBY
Activate Cursor
Tap
Activate TX/STBY
After a few seconds, the icons fade out.
Push or click the Rotary knob.
Crick the Rotary knob will appear the icons
32
Chapter 2 START THE BASIC OPERATION
2 - 1 G UI D E F OR O P E R A TI ON
Front view
Multi-Touch screen.
☆
Operate using “tap” “flick” long tap” “swipe” by fingertip.
Rotary knob.
☆
Rotation: select the sequential menu.
☆
Push or click
fix menu data.
POWER ON OFF, CLEAR PUSH BUTTON.
☆
POWER ON/OFF
☆
CLEAR OF MENU
2 - 2 P O W ER O N ( S T A N D B Y F O R TR A N SMI T)
PRESS PWR / BUTTON
Startup screen
Start to display screen.
33
Chapter 2 START THE BASIC OPERATION
2 - 3 DI S P L A Y S C R E EN
2-3-1 SCREEN LAYOUT
Course
Speed (through ground)
Own ship.
Range
Longitude/Latitude.
depth.
Range interval
Own ship position mark.
Alarm Speaker
USB Port
34
POWER ON OFF,CLEAR PUSH BUTTON.
Push Rotary knob, then appears some menu.
☆
POWER ON/OFF
Rotation of Rotary knob can select menu of activated icon.
☆
CLEAR OF MENU
Function call icon will be displayed.
Chapter 2 START THE BASIC OPERATION
Various ST-BY screen.
Tap
White dot
Tap
△
Normal ST-BY screen,
Normal ST-BY screen,
* ST-BY Disp, Select.:
Normal ST-BY screen,
“Normal”
Tap
White dot
Graphical ST-BY screen
* ST-BY Disp, Select.:
Course
Tap
△
Graphical ST-BY screen
”Graphical”
Speed
Course
Tap
White dot
Numeric Display ST-BY screen.
Course
Speed
Speed
Tap
△
Own ship
position
Own ship
position
* ST-BY Disp, Select.:
Graphical ST-BY screen
Numeric Display ST-BY screen.
Own ship
position
Numeric Display ST-BY screen.
“Numeric Display”
35
Chapter 2 START THE BASIC OPERATION
TX screen.
Push Rotary knob, select TX icon by rotating Rotary knob and push Rotary knob.
Push Rotary knob & select TX icon by rotating.
Set focus to TX icon.
Or
Start TX
Push Rotary knob
Tap TX icon
Tap
△
Tap
▽
Push Rotary knob
36
Tap UP icon
Tap DOWN icon
Chapter 2 START THE BASIC OPERATION
2-3-2 ICON’S TABLE
The icons which will appear by screen operation.
GAIN
RAIN
VRM
GURDZONE
CURSOR
MODE RIVER
SETTING
MODE FIOAT
SEA
MARK
MENU
MODE OFF
BRILLIANCE
AIS
USER1
DAY
TX-STBY
TT
USER2
NIGHT
RANGE
MOB
EBL
OFFCENTER
MODE STANDARD
MODE COAST
37
Chapter 2 START THE BASIC OPERATION
Display the function icons.
Appear icons
after Pushing Rotary knob
No operation about 10 second.
Push Rotary knob
Rotate for icon selection.
Selected icon is focused.
Push Rotary knob, then appear the setting
menu.
Set level by Rotary knob or flick bar graph..
Then push Rotary knob, data is fixed.
38
Rotate Rotary knob
Chapter 2 START THE BASIC OPERATION
Tap TX/STBY icon, or Push rotary knob when TX/STBY icon is focused.
TX
Scanned display
is appeared
ST-BY
Tap icon or push rotary knob
Tap icon or push rotary knob
39
Chapter 2 START THE BASIC OPERATION
Tap GAIN Adjust icon, or Push rotary knob when GAIN Adjust icon is focused.
The case of ST-BY
The case of TX
Adjustment Gain
Adjustment Gain
Bar is appeared
Bar is appeared
Tap “Auto” of Gain setting mode
Tap “Auto” of Gain setting mode
Gain is set
automatically.
Rotate the rotary knob
with monitoring green bar.
Flick the green bar
Or
Tap “+” or “-“
Or
※In TX mode, can be adjusted while monitoring the display echo.
Tap return icon
Push Rotary knob
Or
The data is fixed, and then return
40
Chapter 2 START THE BASIC OPERATION
Tap SEA Adjust icon, or Push rotary knob when SEA Adjust icon is focused.
Adjustment Bar
is appeared
Tap “Auto” of SEA setting mode
Tap “Auto” of SEA setting mode
SEA is set
automatically.
Rotate the rotary knob
with monitoring green bar.
Flick the green bar
Or
Tap “+” or “-“
Or
※Can be adjusted while monitoring the display echo.
Tap return icon
Push Rotary knob
Or
The data is fixed, and then return
41
Chapter 2 START THE BASIC OPERATION
Tap RAIN Adjust icon, or Push rotary knob when RAIN Adjust icon is focused.
Adjustment Bar
is appeared
Tap “Auto” of RAIN setting mode
Tap “Auto” of RAIN setting mode
RAIN is set
automatically.
Rotate the rotary knob
with monitoring green bar.
Flick the green bar
Tap “+” or “-“
Or
Or
※Can be adjusted while monitoring the display echo.
Tap return icon
Push Rotary knob
Or
The data is fixed, and then return
42
Chapter 2 START THE BASIC OPERATION
2-3-3 BRIEF EXPLANATION OF ICON’S FUNCTION
Brief explanation of each icon.
GAIN (gain control) adjustment:
Set up the sensitivity of Radar echo..
SEA (sea-clutter rejection) adjustment:
Control the sea clutter level near the ship.
Long distant echo gain is remaining as it is, and gain is lowered as to short distance.
Adjust the target ship is clearly observe and reject the sea clutter on screen as much as
possible.
RAIN (rain-and-snow-clutter rejection) adjustment:
This type radar uses (X) band microwave (wavelength: 3cm).
This microwave can detectable more far range in fine weather, but in rain or snow weather, the
detectable range decrease remarkably.
The control is adjusted for separate the target and rain or snow as long as possible.
BRILL (brightness) adjustment: Set up the brightness of a screen.
It sets up brightly daytime and sets up not dazzle at night
MOB (Man Over the Boat): When the crew fall into over the boat by accident.
Carry out a tap MOB icon immediately.
The radar memorizes the place latitude and longitude information, and continues displaying
the (MOB)place on a screen.
When going to rescue, navigator can take course to the(MOB)point on screen.
(Important: GPS signal must be connected in this function.)
TT DATA (target tracking)
Data which is tracking automatically is displayed.
Data is display the direction, the distance, the speed.
This function must be required the heading signal and log signal.
Measures reading of a direction can select from north(N-UP) and measure from self-ship
(H-UP).
The speed display can select the relative speed mode or absolute speed mode.
43
Chapter 2 START THE BASIC OPERATION
AIS DATA (when received the AIS signal, the data of MMSI of the vessel which has
transmitted, latitude, longitude, a direction of movement, speed, rate of turn, etc. is displayed.)
(AIS receiver signal is necessary.)
EBL (electronic bearing line)
Measure the target direction by using cursor line.
VRM (variable range marker)
Measure the target distance by using circle line.
Off-center (Normally own position is the center of screen, but it is possible to move own
position from fixed center of screen).
Tap the icon will shift the own position. Shifting point are fixed 5 positions only.
TX (transmission), ST-BY (standby)
Whenever it carries out a tap, transmission and ST-BY are changed.
RANGE (range scale)
The range scale to observe is changed. The maximum range is limited by the scanner type
which is connected.
NKE-1066 scanner
0.0625NM 0.125NM 0.25NM 0.5NM .075NM 1.5NM 3NM 6NM 12NM 24NM.
(Also 1NM, 2NM, 4NM, 8NM, 16NM are possible by system menu setting.)
NKE-2044 scanner
0.0625NM 0.125NM 0.25NM 0.5NM .075NM 1.5NM 3NM 6NM 12NM 24NM 48NM.
(Also 1NM, 2NM, 4NM, 8NM, 16NM, 32NM are possible by system menu setting.)
44
Chapter 2 START THE BASIC OPERATION
Various system setups.
Tap the icon, the adjustment menu will be displayed.
Choose the item to set up individually.
Code input “0” is setting for service menu.
Next
User menu
Special setting menu for user.
45
Chapter 2 START THE BASIC OPERATION
GUARD ZONE setup
Set up the watching area around own-ship.
If a target goes into the set-up area, generate the alarm sound or signal..
On the other hand, if a target goes out the set-up area, generate the alarm sound or signal, too.
One of both is possible to select.
Cursor: A tap is carried out, start, drag and tap off on the target.
The position of this cursor is indicated.
Various kinds of pointing actions uses this cursor..
Tracking of target, AIS data display, setting of guard zone, etc.
MARK: Use when plot a mark on the screen.
Moreover, also when deleting an unnecessary mark, it uses.
46
Chapter 2 START THE BASIC OPERATION
2 - 4 T R A N SMI T
(90 seconds pre-heat time is required for cold start, because of the Magnetron heater.)
After 90 seconds, anytime transmitting is possible.
Various ST-BY screen.
Power ON
Push
PWR/CLR
button
47
Chapter 2 START THE BASIC OPERATION
Start by “the tapping white dot” or “the pushing rotary knob”
White dot
White dot
rotary knob
“Tap TX/ST-BY icon” or “Select TX/ST-BY icon and push rotary knob”, and then transmitting.
TX/ST-BY icon
Select TX/ST-BY icon and push rotary knob
rotary knob
Transmitting screen.
No operation of 10 second,
small menu will be fade out.
48
Chapter 2 START THE BASIC OPERATION
2 - 5 L E A V E T H E U S E F U L I C O N O N S C R E EN
How to copy icon.
Basic icon display.
Fixed icon (TX/ST-BY, Gain)
User free area of menu icon.
Tap UP icon
Full icon display
icons that can be copied
to user free area.
Fixed icon (TX/ST-BY, Gain)
User free area of menu icon.
Tap and hold the icon,
Tapped icon is copied to free menu area
Up to 4 icons can copy the user free area.
49
Chapter 2 START THE BASIC OPERATION
How to remove icon.
Full icon display
Basic icon display.
Tap and hold the icon,
on user free area
Tapped icon is removed from free menu area
Then the remaining icons are shifted to the left.
How to add another icon.
Tap and hold the icon,
Tapped icon is copied to free menu area
50
Chapter 2 START THE BASIC OPERATION
2 - 6 F U N C TIO N C A LL B Y S C R E E N T A P
Various types of icon.
(1) Start function immediately.
(2) Move into function setting.
(3) Double tap start from resist setting state and open menu.
TX, ST-BY
Every tap changes TX, ST-BY alternately
Change Range
tap increase range
tap decrease range
Or
While range icon focused
Or
Rotate the rotary knob
with monitoring range.
Or
Change brightness by Flick the green belt.
Tap “+” or “-“
51
Chapter 2 START THE BASIC OPERATION
Screen brightness adjustment
Tap the icon, then display Adjust menu.
Or
Or
Rotate the rotary knob
with monitoring green bar.
Change brightness by Flick the green belt.
Tap “+” or “-“
Setting level is displayed down side of each icon.
Green bar length is proportion to setting level.
Also using Rotary knob is possible to adjust.
Keep press on the Rotary knob and turn.
Anytime it’s possible to change
Keep press on the Rotary knob.
*”POWER ON–OFF” is operate from “PWR/CLR BUTTON!” only.
Can’t control from screen menu.
52
Chapter 3
ADJUST THE RADAR ECHO
Chapter 3 ADJUST THE RADAR ECHO
▽
△
3 - 1 C H A NG E R AN G E
tap decrease range
tap increase range
This picture is selected 1.5 nm range.
Outer dashed line shows the maximum observation
RANGE
range.
RANGE RING INTAVAL
Gain is easily changed by the tap of increase / decrease icon as
shown in the figure below
tap increase range
tap decrease range
Or
1.5NM
Adjust while range icon focused
by tapping or selection of rotary knob
Or
Rotate the rotary knob
with monitoring green bar.
Or
Change brightness by Flick the green belt.
Tap “+” or “-“
53
Chapter 3
ADJUST THE RADAR ECHO
Range scale,
NKE-1066 scanner
It changes to 0.0625NM 0.125NM 0.25NM 0.5NM .075NM 1NM 1.5NM 2NM 3NM 4NM 6NM 8NM 12NM
16NM 24NM and order.
NKE-2044 scanner
It changes to 0.0625NM 0.125NM 0.25NM 0.5NM .075NM 1NM 1.5NM 2NM 3NM 4NM 6NM 8NM 12NM
16NM 24NM 32NM 48NM and order.
A picture will change on a scale as shown in the following figure, as range changes.
The radius of the circle shows the range.
Example: Video change
0.0625NM
0.125NM
0.25NM
1.5NM
2NM
3NM
12NM
16NM
24NM
32NM
0.5NM
0.75NM
1NM
4NM
6NM
8NM
48NM
is NKE-2044scanner only
54
Chapter 3
ADJUST THE RADAR ECHO
3 - 2 A D J U S T S G AI N ( R AD A R S E N SI TI VI T Y)
Radar must be set suitable gain, or can’t use as a radar
Adjust while Gain icon focused by tapping or selection of rotary knob
icon’s green belt show
the adjusted level of GAIN
How to change the Gain: See the method of Gain adjustment of Chapter2
Example of echo sensitivity as following
echo sensitivity
Low
6NM
echo sensitivity
Middle
echo sensitivity
6NM
High
6NM
If GAIN control is the maximum, noise will appear on whole screen.
GAIN set Exceed
On clear weather normally set almost maximum GAIN.
When rough weather or rough sea or heavy rain and,
snow, adjust mix up SEA,RAIN GAIN.
And select suitable level each.
6NM
55
Chapter 3
ADJUST THE RADAR ECHO
3 - 3 A D J U S T S E A ( C L U T TE R C ON T R O L)
Radar must be set suitable sea control, or can’t use as a radar
Adjust while SEA icon focused by tapping or selection of rotary knob
icon’s green belt show
the set level of SEA
How to change the SEA: See the method of SEA adjustment of Chapter2
SEA Level Low
0.5NM
56
SUITABLE Level
0.5NM
Chapter 3
ADJUST THE RADAR ECHO
3-4 ADJUST RAIN AND SNOW CLUTTER CONTROL
Radar must be set suitable rain and snow control, or can’t display the suitable picture.
Adjust while RAIN icon focused by tapping or selection of rotary knob
icon’s green belt show
the set level of RAIN
How to change the RAIN: See the method of RAIN adjustment of Chapter2
RAIN Small (usually)
6NM
RAIN Excessive (the target of the radius direction becomes small.)
clear weather (RAIN 0)
(RAIN *).
Rain control is effective, if the weather light rain or snow.
Too much suppression will disappear the small target, so set a little.
6NM
not clear weather (RAIN 0).
(RAIN *)
57
Chapter 3
ADJUST THE RADAR ECHO
3 - 5 A D J U S T B RI L LI A N C E OF S C R E E N
Double TAP of screen can change BRILLANCE of screen.
Normal TAP, Flick operations also possible to change screen brilliance.
range.
Double Tap
icon’s green belt show
the set level of BRILLIANCE
How to change the BRILLIANCE: See the method of BRILLIANCE adjustment of Chapter2
58
Chapter 3
ADJUST THE RADAR ECHO
＊＊＊＊FOR
REFERENCE＊＊＊＊
＊＊＊＊
＊＊＊＊
Observing the Radar screen, GANI and SEA control adjustment is essential adjustment.
RAIN: Normally set “0”, when light rain or snow, turn proportion to reject rain noise on screen.
GAIN: Set the GAIN adjustment for long range (more than 6nm) target can observe clear.
Under this conditions, short range near own ship, cannot observe small target because
of high clutter and high gain.
To avoid this failure, use SEA control, and suppress near range clutter noise.
If suitable adjustment is done, costumer can observe clear target from short range to
long range.
ACTUAL OPERATION
Set RAIN Minimum position
① Set 6nm RANGE, and observe more farther special target.
Set GAIN control so as to the special target is observe clearly.
Change to 0.5nm RANGE
Set SEA control so as to the near target can observe clearly.
② Basically, RAIN control is minimum state, but according to the weather conditions,
to reject rain or snow clutter, little bit turn to effective point.
59

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Modify Date                     : 2014:01:06 13:51:25-08:00
Create Date                     : 2014:01:06 13:50:58-08:00
Metadata Date                   : 2014:01:06 13:51:25-08:00
Creator Tool                    : CubePDF
Format                          : application/pdf
Document ID                     : uuid:a1e1a33b-81d0-4176-ad43-c908e57a07b4
Instance ID                     : uuid:fa2a3784-c8a3-4e81-9847-f913ac13a5ce
Producer                        : GPL Ghostscript 9.07; modified using iTextSharp™ 5.4.2 ©2000-2012 1T3XT BVBA (AGPL-version)
Has XFA                         : No
Page Count                      : 31
Creator                         : CubePDF

EXIF Metadata provided by EXIF.tools