Japan Radio Co NKE1066 MARINE RADAR User Manual 5

Download:
Mirror Download [FCC.gov]
Document ID	2183901
Application ID	hkPa1o7VIs0J4723c479DQ==
Document Description	User Manual 5
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	376.79kB (4709820 bits)
Date Submitted	2014-02-05 00:00:00
Date Available	2014-02-05 00:00:00
Creation Date	2014-01-06 13:55:43
Producing Software	GPL Ghostscript 9.07; modified using iTextSharp™ 5.4.2 ©2000-2012 1T3XT BVBA (AGPL-version)
Document Lastmod	2014-01-06 13:55:59
Document Title	User Manual 5
Document Creator	CubePDF

Chapter 8
DETAIL PERFORMANCE SETTING
Chapter 9 MAINTENANCE AND CHECK
9 - 1 R O U TI N E M AI NT E N AN C E
For operating the radar equipment in the good conditions, it is necessary to make the maintenance
work as described below. If maintenance is made properly, troubles will reduce.
It is recommended to make regular maintenance work.
Common points of maintenance for each unit are as follow:
Clean the equipment.
Remove the dust, dirt, and sea water rest on the equipment cabinet with a piece of dry cloth.
Especially, clean the air vents with a brush for good ventilation.
138
Chapter 9
MAINTENANCE AND CHECK
9 - 2 M AI N T EN A N C E OF E A C H U NI T
9-2-1 SCANNER
NKE-1066
DANGER
When conducting maintenance work on the antenna, make
sure to turn its main power off.
Failure to comply may result in electrocution or injuries.
139
Chapter 9
MAINTENANCE AND CHECK
9-2-2 SCANNER
NKE-2044
DANGER
When conducting maintenance work on the antenna, make sure to
turn its main power off.
Failure to comply may result in electrocution or injuries.
140
Chapter 9
MAINTENANCE AND CHECK
9-2-3 DISPLAY NCD-2256
DANGER
When cleaning the display screen, do not wipe it too strongly with
a dry cloth. Also, do not use gasoline or thinner to clean the screen.
Failure to comply will result in damage to the screen surface.
Dust accumulated on the screen will reduce clarity and darken the video.
For cleaning it, wipe it with a piece of soft cloth (flannel or cotton).
Do not wipe it strongly with a piece of dry cloth nor use gasoline or thinner.
141
Chapter 9
MAINTENANCE AND CHECK
9 - 3 P E R F OR M A NC E C H EC K
Make operational check on the radar equipment regularly and if any problem is found,
investigate it immediately.
Pay special attention to the high voltage sections in checking and take full care that no
trouble is caused by any error or carelessness in measurement. Take note of the results of
checking, which can be used effectively in the next check work.
Operational check shall be made in accordance with Table 4.3-1 Function Check List in
the order as specified in it.
Table 9-3-1 Performance Check List
142
Chapter 9
MAINTENANCE AND CHECK
9-3-1 TEST MENU
The performance status of this radar equipment can be checked on the Test Menu.
9-3-2 SYSTEM INFORMATION
Displays the current system information. (software version information).
9-3-3 SYSTEM TIME
Displays the following system time information.
■ Indicator Running Time
■ Scanner Transmit Time
■ Scanner Motor Time
■ Scanner Running Time
143
Chapter 9
MAINTENANCE AND CHECK
9-3-4 SCANNER INFORMATION
Displays the following scanner information.
■ Transmitted output power
■ Motor Type
■ Magnetron Current
9-3-5 HARDWARE INFORMATION
Displays the following hardware information.
■ Serial Number
■ MAC Address
■ Temperature
9-3-6 ERROR LOG
The error log displays previously occurred system alarms with the dates and times when
they occurred.
9-3-7 LINE MONITOR
Serial communication data can be seen on the built-in Line monitor.
Line monitor can be used to make sure that the serial data are received properly
144
Chapter 9
MAINTENANCE AND CHECK
9-3-8 SELF TEST
The following tests can be performed.
■ Key Test
■ Buzzer Test
■ Key Light Test
■ Monitor Display Test
■ Memory Test
■ Line Test
■ Sensor Test
145
Chapter 9
146
MAINTENANCE AND CHECK
Chapter 9
MAINTENANCE AND CHECK
9 - 4 R E P L AC E M EN T O F MAJ O R P A R T S
147
Chapter 9
MAINTENANCE AND CHECK
9-4-1 PARTS REQUIRED FOR PERIODIC REPLACEMENT
Here are parts required for periodic replacement.
PARTS NAME
148
1.
MAGNETRON
2.
MOTOR
INTERVAL
4,000 HOURS
10,000 HOURS
Chapter 9
MAINTENANCE AND CHECK
9 - 5 F A U L T FI N DI NG
9-5-1 ALARMS AND OTHER DISPLAY LISTS
9-5-2 FUSE
9 - 6 T R O UB L E S H OO T IN G
9-6-1 INCLUDED ACCESSORIES
9-6-2 SPECIAL PARTS
Location
Parts No.
Name
Type
Code
Manufacture
NKE-1066
V101
Magnetron
M1624
NKE-2044
V101
Magnetron
MSF1421B
5VMAA00092
New JRC
NKE-2044
A101
Circulator
FCX68R
5AJIX00027
Orient Microwave
NKE-2044
A102
Diode Limiter
NJS6930
5ATBT00006
New JRC
New JRC
149
Chapter 9
MAINTENANCE AND CHECK
9-6-3 CIRCUIT BLOCK TO BE REPAIRED
JMA-1032
Location
Circuit Block
Type
Remarks
Scanner
Motor unit
H-7BDRD0053
Scanner
Modulation circuit
CME-396
Include IF Amplifier
Scanner
Micro wave unit
Transmitter/ receiver
CMN-924/NZT-1066
Include Receiver
frontend
Display Unit
Power Supply circuit
CBD-1928
Display Unit
Process Circuit
CDC-1433
Display Unit
LCD Panel
NZP-2256
JMA-1034
Location
150
Circuit Block
Type
Remarks
Scanner
Motor unit
H7BDRD0052A
Scanner
Modulation circuit
CME-397
Scanner
Receiver
NRG-242
Display Unit
Power Supply circuit
CBD-1928
Display Unit
Process Circuit
CDC-1433
Display Unit
LCD Panel
NZP-2256
NZT-2044
Chapter 9
MAINTENANCE AND CHECK
151
Chapter 10 AFTER-SALE SERVICE
Chapter 10 AFTER-SALE SERVICE
1 0 - 1 K E E PI N G P E RI O D O F M AI N T EN A NC E P A R TS
Keeping period of maintenance parts is ten years from the production is discontinued.
1 0 - 2 W H E N Y O U R E Q U E ST F O R R E P AI R
If you suppose the product may be out of order, read the description in "9-2-5 FAULT
FINDING" and "9-2-6 TROUBLE SHOOTING", and check the suspected point again.
If it is still out of order, you are recommended to stop operation of the equipment and
consult with the dealer from whom you purchased the product, or our branch office in
your country or district, the sales department in our main office in Tokyo.
● Repair within the Warranty Period
If any failure occurs in the product during its normal operation in accordance with the instruction
manual, the dealer or JRC will repair free of charge.
In case that any failure is caused due to misuse, faulty operation, negligence or force major
such as natural disaster and fire, the product will be repaired with charges.
● Repair after the Warranty Period.
If any defective function of the product is recoverable by repair, the repair of it will be made at
your own charge upon your request.
● Necessary Information for Repair
Product name, model, manufacturing date and serial number
Trouble conditions (as detailed as possible. Refer to page "10-4 Radar failure check list".)
Name of company/organization, address and telephone number
1 0 - 3 R E C OM M E N D ED M AI NT E N AN C E
The performance of the product may deteriorate due to the secular change of the parts used in it,
though such deterioration depends upon the conditions of operation.
So checkup and maintenance is recommendable for the product in addition to your daily care.
For maintenance, consult with the near-by dealer or our sales department.
Such maintenance will be made with charges.
For further details of after-sale service, contact the JRC Offices.
152
Chapter 10 AFTER-SALE SERVICE
1 0 - 4 R A DA R F AI L U RE C H E C K LI S T
153
Chapter 11
DISPOSAL
Chapter 11 DISPOSAL
1 1 - 1 DI S P O S A L O F T H E U NI T
When disposing of this unit, be sure to follow the local laws and regulations for the place of
disposal.
154
Chapter 11
DISPOSAL
1 1 - 2 DI S P O S A L O F U S E D M A GN E T R ON
A magnetron is used for the scanner (NKE-1066) (NKE-2044).
☆ When the magnetron is replaced with a new one, return the used magnetron to our
dealer or business office.
For detail, consult with our dealer or business office.
1 1 - 3 C HI N A R O H S
155
Chapter 11
156
DISPOSAL
Chapter 12
SPECIFICATIONS
Chapter 12 SPECIFICATIONS
NKE-1066 scanner
NCD-2256 display
1.5ft scanner 4kw
Radome diameter φ450mm
NKE-2044 scanner
Display 7inches wide LCD
2ft Scanner 4kw
Radome diameter φ620mm
158
Chapter 12
SPECIFICATIONS
1 2 - 1 S C A NN E R DI M E N SI O N
12-1-1 NKE-1066
NKE-1066
1.5ft scanner 4kw radome φ450mm
4-φ40 RUBBER PLATE
159
Chapter 12
SPECIFICATIONS
12-1-2 NKE-2044
160
Chapter 12
SPECIFICATIONS
1 2 - 2 DI S P L A Y DI M EN SI O N
12-2-1 NCD-2256
161
Chapter 12
162
SPECIFICATIONS
Chapter 12
SPECIFICATIONS
1 2 - 3 E Q UI PM E N T OU T LI N E
１）This equipment is a marine radar for vessels and work boats which consists of the display
unit including 7 inch wide VGA color LCD Monitor unit, Keyboard unit, Processing unit and
consists of the 1.5 ft /2ft radome type scanner unit. The processing unit uses SOC (LUPIM)
developed by JRC and the LCD monitor unit uses panel with touch sensor (resistance film type).
The operation can be realized intuitive and simple.
12-3-1 CONFIGULATION
CONFIGURATION
12-3-1
1) Display unit NCD-2256
・ Integrated the 7 inch wide VGA color LCD Monitor unit, Keyboard unit and Processing unit
2) Scanner unit
・ X-band 1.5ft(4kW)
・ X-band 2ft(4kW)
radome type is NKE-1066
radome type is NKE-2044
12-3-2 FEATURE
1) The screen resolution is 800x480dots (WVGA).
The LCD monitor unit with touch sensor (resistance film type).
2) Highly efficient signal processing using the SOC including DSP.
3) TT and AIS function are prepared by SOC using.
12-3-3 RADAR MODEL
JMA-1032
JMA-1034
1.5ft Scanner unit
2.ft Scanner unit
163
Chapter 12
SPECIFICATIONS
12-3-4 SYSTEM DIAGRAM
JMA-1030 Series system diagram
1.5feet Scanner Unit
(NKE-1066)
Radome diameter 450mm
2feet Scanner Unit
(NKE-2044)
Radome diameter 620mm
CFQ9924-5,10,15,20,300
*STANDARD LENGTH 10m
OPTION:
(cablelength:5m/15m/20m/30)
JMA-1032 RADAR
JMA-1034 RADAR
External Navigational
Signal input.
NMEA 3 input ports
(GPS,AIS,DEPTH)
Ship’s Main Power
(10.8-31.2VDC)
CFQ-9900
(cable length 2m)
*INCLUDING FUSE IN PLUS LINE
FUSE TYPE: 7.5A/58V
164
7inch WIDE VGA COLOUR LCD DISPLAY
(NCD-2256)
Chapter 12
SPECIFICATIONS
1 2 - 4 G E N E RA L S P E C IFI C A TI O N S
(1) Class of Emission
P0N
(2) Display
Color Raster Scan
(3)Display capability
WVGA (800x480dots) Screen
(4) Screen
7-inch Color LCD with touch sensor (resistance film type)
(5) Range Scale
0.0625, 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48NM
(48 NM: only 2feet type scanner is available)
User can add 1, 2, 4, 8, 16, and 32NM
(32 NM: only 2feet type scanner is available)
(6) Range Resolution
Less than 30m
(7) Minimum Detective Range
Less than 40m
(8) Range Accuracy
Less than 1% of the maximum distance of the range scale
in use or less than 15m whichever is greater.
(9) Bearing Accuracy
Less than ±1°
(10) Bearing Indication
RM: Head-up, North-up, Course-up
TM: North-up, Course-up
(11) Ambient Condition
Standards
IEC60945 Ed.4.0
Temperature
Scanner
Operation: -25 to +55°C / Storage: -25 to +70°C
Other Unit except Scanner Operation: -15 to +55°C / Storage: -15 to +70°C
Relative Humidity
+40°C, 93%
Vibration
2 to 13.2 Hz, amplitude±1mm
13.2 to 100 Hz 0.7 G
Velocity of the wind
100kn
Waterproof/dustproof
Scanner
IP26
Display unit
IP55
(12) Power Supply Input
DC 10.8-31.2V (DC12-24V-10%+30%)
(13) Power Consumption
Approx. 50W (NKE-1066/NKE-2044).
Maximum: 50W (NKE-1066: SP1,
NKE-2044: LP2
transmitting)
(14) Pre heat time
Approx. within 1min30sec.
(15) Display unit
Refer to Display unit Specifications
(16)Inter-unit Cables
Using common scanner connecting cable CFQ-9924-10
Standard Length 10m
Maximum cable length 30m
165
Chapter 12
SPECIFICATIONS
1 2 - 5 S C A NN E R
12-5-1 SCANNER (NKE-1066) SPECIFICATION
(1) Dimensions
Height 231mm×Diameter of radome 450mm
(2) Mass
Approx. 5.5kg
(3) Polarization
Horizontal (antenna length 1.5 feet)
(4) Antenna Directivity
Horizontal Beam Width (-3dB)
5.2°
Vertical Beam Width (-3dB)
25°
Side lobe Level
Less than -21dB (less than ±10° from the main lobe)
(5) Rotation
Approx. 27rpm (16/27/36/48rpm are available)
(6) Transmitting Frequency
9410±30MHz
(7) Peak Power
4 kW
(8)Transmitting Tube
Magnetron [M1624]
(9) Pulse width/ Repetition Frequency (Bandwidth)
SP1: 0.08µs/4000 Hz (Wide 20MHz)
SP2: 0.08µs/2250 Hz (Wide 20MHz)
SP3: 0.13µs/1700 Hz (Wide 20MHz)
MP1: 0.25µs/1700 Hz (Middle 6MHz)
MP2: 0.5µs/1200 Hz (Narrow 3MHz)
LP1: 0.8µs/750 Hz (Narrow3 MHz)
(S: Short pulse, M: Middle pulse, L: Long pulse)
(10) Range Information
(11) Duplexer
0.0625NM SP1
0.125NM
SP1
0.25 NM
SP1
0.5 NM
SP1 / MP1
0.75 NM
SP2 / MP1
1.5 NM
SP2 / MP1 / MP2
3 NM
SP3 / MP1 / MP2
6 NM
MP2 / LP1
12 NM
MP2 / LP1
24 NM
LP1
Circulator + Diode Limiter
(Diode Limiter is included in the frontend)
166
(12) Front End Module
MIC
(13) IF Frequency
60MHz
(14) IF AMP
Log Amplifier (Gain: more than 90dB)
(15) Overall Noise Figure
6dB(Average)
(16) Tuning
Manual/Auto
Chapter 12
SPECIFICATIONS
12-5-2 SCANNER (NKE-2044) SPECIFICATION
(1) Dimensions
Height 280mm×Diameter of radome 620mm
(2) Mass
Approx. 10.5kg
(3) Polarization
Horizontal (antenna length 2 feet)
(4) Directional Characteristic
Horizontal Beam Width (-3dB)
4°
Vertical Beam Width (-3dB)
25°
Side lobe Level
-21dB or less (less than ±10° from the main lobe)
(5) Rotation
Approx. 27rpm (16/27/36/48rpm are available)
(6) Transmitting Frequency
9410±30MHz
(7) Peak Power
4 kW
(8)Transmitting Tube
Magnetron [MSF1421B]
(9) Pulse width/ Repetition Frequency (Bandwidth)
SP1: 0.08µs/4000 Hz (Wide 20MHz)
SP2: 0.08µs/2250 Hz (Wide 20MHz)
SP3: 0.13µs/1700 Hz (Wide 20MHz)
MP1: 0.25µs/1700 Hz (Middle 6MHz)
MP2: 0.5µs/1200 Hz (Narrow 3MHz)
LP1: 0.8µs/750 Hz
(Narrow3 MHz)
LP2:1.0us/650Hz
(Narrow:3MHZ)
(S: Short pulse, M: Middle pulse, L: Long pulse)
(10) Range Information
0.0625NM SP1
0.125NM
SP1
0.25 NM
SP1
0.5 NM
SP1 / MP1
0.75 NM
SP2 / MP1
1.5 NM
SP2 / MP1 / MP2
3 NM
SP3 / MP1 / MP2
6 NM
MP2 / LP1/ LP2
12 NM
MP2 / LP1/ LP2
24 NM
LP2
48 NM
LP2
(11) Duplexer
Circulator + Diode Limiter
(12) Front End Module
MIC
(13) IF Frequency
60MHz
(14) IF AMP
Log Amplifier (Gain: more than 90dB)
(15) Overall Noise Figure
6dB(Average)
(16) Tuning
Manual/Auto
167
Chapter 12
SPECIFICATIONS
1 2 - 6 DI S P L A Y
12-6-1 INTEGRATED DISPLAY UNIT (NCD-2256)
1) Structure
Desk Top Integrated Type
(LCD Monitor Unit/Keyboard Unit/Processor Unit Integrated Structure)
Vertical installation only desk top integrated type
Option: Overhead Mounted kit installation
2) Dimensions
Height 235.2mm × Width 162mm × Depth 77.3mm
(The U style mount base and the both sides knob bolts are
included.)
3) Mass
Approx. 1.8kg
4) Tune Method
Manual / Auto
(Bar-graph indication is displayed at the time of adjustment.)
5) STC (SEA)
Manual / Auto
6) FTC (RAIN)
Manual / Auto
7) Radar Interference Rejection
Built-in (The effect can be adjusted by three stages.)
8) Bearing Marker
360° in 5° digit
9) Heading Line
Electronic
10) Off Center
move to the defined coordinates of 4 patterns
(4 patterns are back side 64dots,left side 92dots, front side
92dots, right side 92dots from the default center position)
Transition of the radar trails is possible during Off Center mode.
11) True Motion Unit
Built-in (Not available at the maximum range)
12) True Motion Reset Position
40% of radius of any range
13) Radar trail indication
True motion mode:
Only true motion trails
Relative motion mode:
Only relative motion trails
Trail time length:
15 sec to 15 min/Continuous
30 sec to 30 min/Continuous
1 min to 1 hr/Continuous
30 min to 12 hr/Continuous
Arbitrary trail time length can be displayed at any time.
Possible to display time series trail and continuous trail
by color classification.
* When switching to true/relative trails, the radar trails
are cleared. Transition of the trails is possible during Off
Center mode (Relative motion). (Scroll)
When the bearing mode is switched (RM (T), TM), the
radar trails are taken over at between RM (T) and TM.
168
Chapter 12
SPECIFICATIONS
14) Variety of Pulse width SP1/ SP2/ SP3/ MP1/ MP2/ LP1/ LP2
(LP2 is JMA-1034 only)
15) Target enhance
3 stages
16) Plotting
3 marks
17) Display color
Radar echo
16 stages, 8 colors (Yellow, Green, Blue, White, Magenta, Gold,
Amber, Color)
Radar trails
1 stage,
Time trails: 3 colors (Green, Blue, Cyan)
Continuous trails: 3 colors (Green, Blue, Cyan)
Background
PPI: 3 colors (Black, Blue, White)
Characters
7 colors (White, Cyan, Green, Black, Red, Gold, Amber)
AIS/TT
3 colors (Cyan, Green, White)
EBL/VRM
4 colors (Cyan, Black, Magenta, White)
Cursor
4 colors (White, Red, Magenta, Yellow)
Own Ship's
6 colors (Cyan, Green, Red, White, Gold, Amber)
Range Ring
6 colors (Cyan, Green, Red, White, Gold, Amber)
Alarm Zone
5 colors (White, Green, Orange, Black, Red)
18) Simulator
Built-in
19) Multiple languages
English, Spanish, Turkish, Indonesian, Thai, Malay, Vietnamese,
Chinese, Russian, Korean, Japanese, Other optional language
20) Range Unit
NM, Km, sm
21) Navigation information during STBY
Built-in
22) AIS information display
(MMSI, ship name) List display, WPT setting,
Can display ship name only
169
Chapter 12
SPECIFICATIONS
12-6-2 OPERATIONAL PANEL
1) Structure
Integrated on the display unit
PWR/CLR
2) Key
Short push: Power ON ( at the time of Power OFF)
Long push: Power OFF
PWR/CLR
3) Knob Controller
Short push: input cancel, back to a up-layer
PUSH : Menu or Icon selection and execution, control
EBL/VRM, number input, Enter, etc.
PUSH + rotation: Brilliance control
4) Touch control
Tap: Menu or Icon selection and execution, control, etc.
Double tap: Brilliance menu
Icon Double tap: EBL/VRM disappear
Icon Long tap: Entry of short cut Icon
12-6-3 AIS FUNCTION (STANDARD BUILT IN)
1) Display
Number of targets
Up to 50 targets (stores up to 500 ship static data)
Target information
Displays MMSI, call sign, ship name, COG, SOG, CPA, TCPA, direction,
distance, latitude, longitude, status, etc.
Filters
Distance only
Active targets
Not available
Dangerous ship targets
No CPA/TCPA decision
2) Operation
Built-in
12-6-4 TT FUNCTION (STANDARD BUILT IN)
1) Acquisition
MANUAL/AUTO (by automatic acquisition/activation zone)
2) Tracking
10 targets (Automatic tracking)
3) Display
Tracking data
1 ship (AIS or TT)
Maximum tracking range
20NM (This varies depending on the range)
Target information
Displays items selected from true bearing, distance,
true course, true speed, CPA, TCPA.
Display of Vectors
4) Operation
170
True/Relative
Built-in
Chapter 12
SPECIFICATIONS
1 2 - 7 IN P U T/ O U T PU T SI G N AL
Telecommunications standard
NMEA0183 / 61162 -1/2
Communications protocol
4800 bps, start 1bit, data 8bit, stop 1bit,
non parity
Input sentence
NMEA0183:
V1,5: GGA/ GLL/ RMC
V2,0: GGA/G LL/ RMC/ZDA
V2,3 : GGA/GLL/RMC/GNS/ZDA
(Talker=”GP” etc.)
Information classification
position and time
GGA/G NS/G LL/RMC
date
ZDA/RMC
Time
ZDA/GGA/GNS/GLL/RMC
12-7-1 INPUT ENABLE SIGNAL
(Three-port input GPS/HDG/AIS)
(1) Navigation equipment IEC61162-1/2(※1)
L/L:
GGA>RMC>RMA>GNS>GLL
SOG/COG:
RMC>RMA>VTG
Log speed:
VBW>VHW
HEADING:
THS>HDT>HDG>HDM
DEPTH:
DPT>DBT
WATER TEMP:
MTW
ROT:
ROT
RUDDER:
RSA
AIS:
VDM, VDO, ALR
WIND:
MWV>VWT, VWR
WAYPOINT:
WPL
(2) Bearing signal JRC-NSK format (JLR-10/20/30)(by NMEA3 port)
IEC61162-1/2(※1) 4800bps/38400bps: THS>HDT>HDG>HDM
(3) Speed signal IEC61162 4800bps: VBW, VHW
※1:IEC61162-2 Conformity is unnecessary.
(Insulation is unnecessary. Input electrical tests are unnecessary.)
171
Chapter 12
SPECIFICATIONS
12-7-2 OUTPUT POSSIBLE SIGNAL (THREE-LINE GPS/HDG/TTM)
(1) Navigation equipment
Radar date:
RSD
Own ship’s data: OSD
TT data:
TTM, TTL, TTD
Latitude/ Longitude data: GGA, RMC, GNS, GLL,
COG/SOG:
VTG (Received GPS data)
Bearing signal: THS, HDT (Received GPS Compass data)
(2) External Buzzer
Factory presetting: normal open contacts
(3) Output RGB signal
To incorporate optional kit (NQA-2447) is necessary
※In this case, waterproofing (IPx5) of rear side of display unit is not guaranteed
(4) Slave display
no function
(5) LAN
no function
12-7-3 STANDARD CONFIGURATION
Scanner:
1unit
Display Unit:
1unit
Sun cover:
1unit
Scanner cable:
1pc.
(10m)
Power cable:
1pc.
(2m)
Standard included accessories:
1set (2 pieces. fuse)
Instruction /Installation/Quick manual:
1 book
12-7-4 OPTION CABLE
Scanner cable: 5m, 15m, 20m,30m
NMEA cable (waterproof (IPx5)): 1m
172
Chapter 13
APPENDIX
Chapter 13 APPENDIX
NKE-1066(1.5FT) SCANNER INTRCONNECTION DIAGRAM
FIG A1
APPENDIX－1
Chapter 13
APPENDIX
NKE-2044(2FT) SCANNER INTRCONNECTION DIAGRAM
FIG A2
APPENDIX-2
Chapter 13
APPENDIX
NCD-2256 DISPLAY UNIT INTER CONNECTION DIAGRAM
FIG A3
APPENDIX－3
Chapter 13
APPENDIX
JMA-1030 PRIMARY POWER SUPPLY DIAGRAM
FIG A4
APPENDIX-4
Chapter 13
APPENDIX
JMA-1030 INTER CONNECTION DIAGRAM
FIG A5
APPENDIX－5
Chapter 13
APPENDIX
90mm
140
mm
FIG A6
APPENDIX-6
Chapter 13
APPENDIX
O P E RA TI O N S H E E T
90mm
GAIN
RAIN
SEA
VRM
GURDZONE
MARK
CURSOR
SETTING
MENU
TT ACTIV
TT ST-BY
DAY
140
mm
AIS ACTIV
USER1
NIGHT
TX-STBY
AIS SLEEP
USER2
MODE RIVER
RANGE
MOB
BRILLIANCE
EBL
OFFCENTER
MODE STANDARD
MODE COAST
MODE FIOAT
MODE OFF
FIG A7
APPENDIX－7
MENU FUNCTION LIST
M EN U F U NC TI O N LI S T
Main Menu
Item
Setting Contents
1. RADAR Echo
1. Pulse Length
SP/MP/LP
2. IR
OFF / Low / Middle / High
3. Target Enhance
OFF / Level1 / Level2 / Level3
4. Process
OFF / 3Scan COREL / 4Scan COREL / 5Scan COREL / Remain / Peak Hold
5. Zoom
OFF / ON
6. Video Latitude
Narrow / Normal / Wide1 / Wide2
7. Video Noise Rejection
OFF / Level1 / Level2 / Level3
8. Timed TX
OFF / ON
2. Tuning
3. Motion Mode
1. Motion
RM, TM
2. Bearing Mode
HUP/NUP/CUP
4. Radar trail
1. Trails REF Level
Level1 / Level2 / Level3 / Level4
2. Time/All Combine
OFF / ON
3. Trails Mode
True/Relative
4. Trails Interval
OFF/15sec/30sec/1min/2min/3min/4min/5min/6min/10min/15min/CONT
5. Vector Length
1. Vector Mode
True/Relative
2. Vector Length
1 - 60min
6. Maker
1. Maker Mode
True/Relative
2. VRM Unit
NM/km/sm
3. EBL Bearing Mode
Heading Fix / Screen Fix
4. Range Rings(RR)
OFF / ON
7. Target
1. Function ON/OFF
1. TT
OFF / ON
2. AIS
OFF / ON
2. CPA Limit
0.1 - 9.9NM
3. TCPA Limit
1 - 99min
APPENDIX-8
MENU FUNCTION LIST
Item
Setting Contents
4. CPA Ring Display
OFF / ON
5. Target Number Display
1. TT
OFF / ON
2. AIS
OFF / ON
6. ALR Alarm From AIS
OFF / ON
7. AIS Display Targets
20 / 30 / 40 / 50
8. AIS List Display
OFF / ON
8. NMEA Info. Set
APPENDIX－9
MENU FUNCTION LIST
Initial setting Menu
Item
1. Basic Adjustment
1. Bearing Adjustment
2. Range Adjustment
3. Tune Adjustment
4. Antenna Height
5. Noise Level
6. Language
2. RADAR Echo
1. Main Bang Suppression
1. MBS Level
2. MBS Area
2. Target Enhance Level
3. Gain Preset
4. STC
1. STC Curve Select
2. STC Slope Correction
3. STC Offset
1. FTC
1. FTC Curve Select
2. FTC Slope Correction
3. FTC Offset
6. RADAR Alarm
1. RADAR Alarm1 Level
2. RADAR Alarm2 Level
Setting Contents
0.0 - 359.9
0 - 999
0 - 127
~5m/5~10m/10~20m/20m~
0 - 255
English/Spanish/Turkish/Indonesian/Thai/Malay/Vietnamese/
Chinese/Japanese/Korean/Russian
0 - 255
0 - 255
Level1/Level2/Level3/Level4
0 - 255
Sea/River
0.0 - 2.0
0 - FF
Sea/River
0.0 - 2.0
0 - FF
Level1/Level2/Level3/Level4
Level1/Level2/Level3/Level4
3. RADAR Trails
1. MAX Interval
2. Suppression Distance
Short/Middle/Long/Super Long
0 - 1000
4. TT
1. Vector Constant
2. Gate Display
3. Gate Size
1-8
OFF / ON
0 - 64
5. Scanner
1. PRF Fine Tuning
2. Stagger Trigger
3. Antenna Rotation Speed
1. SP1
2. SP2
3. SP3
4. MP1
5. MP2
6. LP1
7. LP2 (*NKE-2044 only)
4. PRF Mode
5. Timed TX
1. TX Time
2. STBY Time
3. Adaptation
6. Tune Peak Adjustment
7. Tune Indicator Level
6. I/F Device
1. Heading Equipment
2. Manual Heading
3. Speed Equipment
4. Manual Speed
5. MAG Compass Setting
1. Heading Correction
2. Correct Value
APPENDIX-10
0 - 31
OFF / ON
0-7
0-7
0-7
0-7
0-7
0-7
0-7
Normal/Economy/High Power
1 - 99
1 - 99
ON/OFF
0 – 127
0 - 127
AUTO/GYRO/Compass/GPS/Manual
0.0 - 359.9
GPS/Log/2axis Log/Manual
0.0 - 100.0kn
OFF / ON
W9.9 - E9.9°
MENU FUNCTION LIST
Item
Setting Contents
7. COM Port Setting
1. Baud Rate
1. NMEA1
2. NMEA2
3. NMEA3
2. RX Port
1. GPS
2. Log
3. 2axis Log
4. Depth
5. Temperature
6. Wind
7. WPT
8.Rate of Turn
9. Rudder
3. TX Port
1. TTM
2. TLL
3. TTD
4. TLB
5. GGA
6. GLL
7. RMC
8. GNS
9. VTG
10. THS
11. HDT
12. OSD
13. RSD
4. TX Data Format
1. TX Interval
2. NMEA Version
3. NMEA Talker
5. Target Info. TX
1. TX Target
2. TTM Range Accuracy
3. TT Average Mode
4. TT Average Scan
AUTO/4800bps/38400bps
AUTO/4800bps/38400bps
AUTO/4800bps/38400bps
AUTO/NMEA1/NMEA2/NMEA3
AUTO/NMEA1/NMEA2/NMEA3
AUTO/NMEA1/NMEA2/NMEA3
AUTO/NMEA1/NMEA2/NMEA3
AUTO/NMEA1/NMEA2/NMEA3
AUTO/NMEA1/NMEA2/NMEA3
AUTO/NMEA1/NMEA2/NMEA3
AUTO/NMEA1/NMEA2/NMEA3
AUTO/NMEA1/NMEA2/NMEA3
OFF/NMEA1/NMEA2/NMEA3
OFF/NMEA1/NMEA2/NMEA3
OFF/NMEA1/NMEA2/NMEA3
OFF/NMEA1/NMEA2/NMEA3
OFF/NMEA1/NMEA2/NMEA3
OFF/NMEA1/NMEA2/NMEA3
OFF/NMEA1/NMEA2/NMEA3
OFF/NMEA1/NMEA2/NMEA3
OFF/NMEA1/NMEA2/NMEA3
OFF/NMEA1/NMEA2/NMEA3
OFF/NMEA1/NMEA2/NMEA3
OFF/NMEA1/NMEA2/NMEA3
OFF/NMEA1/NMEA2/NMEA3
1 - 9sec
V1.5/V2.0/V2.3
Normal/GP
TT/AIS/TT-AIS
1/2/3
OFF / ON
2 - 10
8. JRC GPS
1. GPS Status
2. GPS Setting
1. NMEA Version
2. Correction Method
3. Fix Mode
4. Elevate Mask
5. HDOP
6. Smoothing LL
7. Smoothing SOG
8. Smoothing COG
AUTO/V1.5/V2.0/V2.3
GPS Single/SBAS/Beacon/AUTO
2D/3D/AUTO
5 - 89°
4/10/20
0 - 99sec
0 - 99sec
0 - 99sec
0 - 99sec (R29.04 - R33.99)
1 - 99sec (R26.01 - R29.03)
0sec/10sec/40sec
OFF/10/30/50/100m
9. Smoothing
10. Smoothing
11. RAIM Accuracy Level
12. Exclusion Satellite
1. Exclusion Satellite1
2. Exclusion Satellite2
3. Exclusion Satellite3
4. Exclusion Satellite4
5. Exclusion Satellite5
6. Exclusion Satellite6
0 - 32
0 - 32
0 - 32
0 - 32
0 - 32
0 - 32
APPENDIX－11
MENU FUNCTION LIST
Item
Setting Contents
13. Send Data
14. GPS Adjust
1. Position
2. Antenna Height
3. Time
4. Date
5. Master Reset
6. Send Data
3. Beacon Setting
1. Station Select
2. Frequency
3. Baud Rate
4. Send Data
4. SBAS Setting
1. Satellite Search
2. Ranging
3. SBAS Satellite Number
4. Send Data
9. Control
1. Touch Panel Calibration
2. Bearing Reference (*NKE-2044 only)
3. Buzzer
1. Key ACK
2. Operation Error
3. CPA/TCPA
4. AZ/Alarm Zone
5. Target Lost
6. System Alarm
10. Maintenance
1. Partial Reset
1. All Menu
2. RADAR Echo
3. Function Setting
4. Initial Setting Menu
5. Main Menu
6. Adjust Menu (*NKE-2044 only)
7. System Information 1 (*NKE-2044 only)
8. System Information 2 (*NKE-2044 only)
2. All Reset
3. System Time Clear
4. Scanner Time Clear
1. TX Time Clear
2. Motor Time Clear
3. ANT to DISP Unit
4. DISP to ANT Unit
5. Table Update
1. Initial Value
1. All Menu
2. RADAR Echo
3. Function Setting
4. Initial Setting Menu
5. Main Menu
6. Adjust Menu
(*NKE-2044 only)
7. System Information 1
(*NKE-2044 only)
8. System Information 2
(*NKE-2044 only)
2. Insert Language
3. Echo Simulation (*NKE-2044 only)
4. STC Curve
5. Color Pallet (*NKE-2044 only)
APPENDIX-12
0 - 8191m
00:00:00 - 23:59:59
2013/1/1/ - 2099/12/31
AUTO/Manual
283.5 - 325.0kHz
50 / 100 / 200bps
AUTO/Manual
OFF / ON
120 - 138
True/Relative
OFF/1 - 5
OFF/1 - 5
OFF/1 - 5
OFF/1 - 5
OFF/1 - 5
OFF/1 – 5
MENU FUNCTION LIST
Item
Setting Contents
6. Internal Setting
1. Internal Memory to USB
1. All Menu
2. RADAR Echo
3. Function Setting
4. Initial Setting Menu
5. Main Menu
6. Mark Setting
7. Adjust Menu
(*NKE-2044 only)
8. System Information 1
(*NKE-2044 only)
9. System Information 2
(*NKE-2044 only)
2. USB to Internal Memory
1.All Menu
2. RADAR Echo
3. Function Setting
4. Initial Setting Menu
5. Main Menu
6. Mark Setting
7. Adjust Menu
(*NKE-2044 only)
8. System Information 1
(*NKE-2044 only)
9. System Information 2
(*NKE-2044 only)
7. USB Format
11. System Setting
1. Master/Slave/DEMO
2. Own Ship Outline
1. All Length
2. All Width
3. Scanner (from Bow)
4. Scanner (from Cntr.)
3. Unit
1. Range
2. Distance
3. Speed
4. Depth
5. User Depth
6. Temperature
7. Wind
4. Move Own Ship
1. Ship's Move Method
5. Range
1. NM
Master/Slave/Demo
0.0 - 600.0m
0.0 - 200.0m
0.0 - 600.0m
-100.0 – 100.0m
NM/km/sm
NM/km/sm
kn/ km/h /mph
ft/fm/m/user
0.1 - 10.0
°C /°F
m/s / km/h / kn / Bft.
LL / COG/SOG
1. 0.0625NM
2. 0.125NM
3. 0.25NM
4. 0.5NM (*NKE-2044 only)
5. 0.75NM (*NKE-2044 only)
4. 1NM
5. 2NM
6. 4NM
7. 8NM
8. 16NM
9. 24NM
10. 32NM
11. 48NM
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
APPENDIX－13
MENU FUNCTION LIST
Item
Setting Contents
2. km
1. 0.15km
2. 0.3km
3. 0.5km (*NKE-2044 only)
4. 1.2km
5. 2km
6. 8km
7. 16km
8. 32km
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
1. 0.0625sm
2. 0.125sm
3. 0.25sm
4. 1sm
5. 2sm
6. 4sm
7. 8sm
8. 16sm
9. 24sm
10. 32sm
11. 48sm
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
OFF / ON
3. sm
12. Display Screen
1. Own Vector Display
2. STBY Disp. Select
3. Operation Num Disp.
4. Display Color
1. PPI
1. Color
2. Brilliance
2. Inner PPI (*NKE-2044 only)
1. Color
(*NKE-2044 only)
2. Brilliance
(*NKE-2044 only)
3. Character
1. Color
2. Brilliance
4. RADAR Echo
1. Color
2. Brilliance
5. RADAR Trails (Time)
1. Color
2. Brilliance
6. RADAR Trails (All)
1. Color
2. Brilliance
7. Own Ship's
1. Color
2. Brilliance
8. Target (TT/AIS)
1. Color
2. Brilliance
9. EBL/VRM
1. Color
2. Brilliance
10. Range Ring
1. Color
2. Brilliance
11. Cursor
1. Color
2. Brilliance
APPENDIX-14
OFF / ON
Normal / Graphical / Numeric Display
OFF / ON
Black/ Blue/ White
Level1/ Level2/ Level3/ Level4
Black/ Blue/ White
Level1/ Level2/ Level3/ Level4
White/Cyan/Green/Black/Red/Gold/Amber
Level1/ Level2/ Level3/ Level4
Yellow/Green/Blue/White/Magenta/Gold/Amber/Color
Level1/ Level2/ Level3/ Level4
Green/Blue/Cyan
Level1/ Level2/ Level3/ Level4
Green/Blue/Cyan
Level1/ Level2/ Level3/ Level4
Cyan/Green/Red/White/Gold/Amber
Level1/ Level2/ Level3/ Level4
Cyan/Green/White
Level1/ Level2/ Level3/ Level4
Cyan/Black/Magenta/White
Level1/ Level2/ Level3/ Level4
Cyan/Green/Red/White/Gold/Amber
Level1/ Level2/ Level3/ Level4
White/Red/Magenta/Yellow
Level1/ Level2/ Level3/ Level4
MENU FUNCTION LIST
Item
Setting Contents
12. AZ/Alarm Zone
1. Color
2. Brilliance
White/Green/Orange/Black/Red
Level1/ Level2/ Level3/ Level4
ON/OFF
0.0 - 48.0
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 - 999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 – 999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 - 999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 - 999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
3. Connection Device (*NKE-2044 only)
1. GYRO(Time Out) (*NKE-2044 only)
1. Alarm Sensitivity
(*NKE-2044 only)
2. Sensitivity Time
(*NKE-2044 only)
2. Log(Time Out) (*NKE-2044 only)
1. Alarm Sensitivity
(*NKE-2044 only)
2. Sensitivity Time
(*NKE-2044 only)
3. GPS(Time Out) (*NKE-2044 only)
1. Alarm Sensitivity
(*NKE-2044 only)
2. Sensitivity Time
(*NKE-2044 only)
OFF / ON
5. Waypoint Display
6. AIS Filter
13. Error Alarm Mask
1. Scanner
1. Scanner(Time Out)
2. Scanner(Data)
3. Scanner(Video)
4. Scanner (Trigger)
5. Scanner(AZI)
6. Scanner(HL)
7. Scanner(MHV)
8. Scanner(Heater)
2. Display Unit
1. Display Unit(Video)
2. Display Unit(Trigger)
3. Display Unit(AZI)
4. Display Unit(HL)
5. Display Unit(DSP)
6. COM Port
OFF / ON
0 -999sec
OFF / ON
0 -999sec
OFF / ON
0 -999sec
APPENDIX－15
MENU FUNCTION LIST
Item
Setting Contents
4. RX Data
1. GYRO
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Alarm Sensitivity
2. Sensitivity Time
OFF / ON
0 -999sec
1. Indicator Software
2. Boot
3. DSP (MC)
4. DSP (V)
5. Test Bench
6. Scanner Software
7. Update
1.0.0
01.06
01.00.00.00
01.00.00.00
01.04
04.02
01.06
2. Compass
3. Log
4. 2Axis Log
5. Course/Speed
6. Depth
7. Temperature
8. Wind
9. Rate of Turn
10. Rudder
11. WPT
12. LAT/LON
13. Datum
14. Status
15. HDOP
16. AIS
14. Test
1. System Information
APPENDIX-16
MENU FUNCTION LIST
Item
Setting Contents
2. System Time
1. Scanner Transmit Time
2. Scanner Motor Time
3. Scanner Running Time
4. Indicator Running Time
3. Scanner Information
1. Scanner Transmit Power
2. Motor Type
3. Magnetron Current
4. Hardware Information
1. Serial Number
2. MAC Address
5. Error Log
1. Display
2. Erase
6. Line Monitor
1. Scanner
2. NMEA1
3. NMEA2
4. NMEA3
7. Self Test
1. Key Test
2. Touch Panel Test
3. Buzzer Test
4. Key Light Test
5. Monitor Display Test
Pattern1
Pattern2
Pattern3
Pattern4
Pattern5
Pattern6
Pattern7
RGB Setting
Red
Green
Blue
Display
6. Memory Test
1. SDRAM
2. Flash ROM
3. USB
7. Line Test
1. Scanner
2. NMEA1 or GPS(JRC)
3. NMEA2
4. NMEA3 or NSK
8. Scanner Test
1. SSW Off
2. BP
3. BZ
4. Mod.HV
5. Trigger
6. Video
APPENDIX－17
MENU FUNCTION LIST
APPENDIX-18
Not use the asbestos
JRC website http://www.jrc.co.jp/
Marine Service Department
Telephone: +81-3-3492-1305
Facsimile: +81-3-3379-1420
e-mail tmsc@.jrc.co.jp
Amsterdam branch
Telephone: +31-(0)20-658-0750
Facsimile +31-(0)20-658-0755
e-mail service@jrceurope.com
Seattle branch
Telephone: +1-(0)206-654-5644
Facsimile: +1-(0)206-654-7030
e-mail service@jrcamerica.com
01JTM
ISO 9001 and ISO 14001 Certified
Code No.7ZPRD0895
Dec, 2013 creation
The 1st edition
JRC

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Modify Date                     : 2014:01:06 13:55:59-08:00
Create Date                     : 2014:01:06 13:55:43-08:00
Metadata Date                   : 2014:01:06 13:55:59-08:00
Creator Tool                    : CubePDF
Format                          : application/pdf
Document ID                     : uuid:bb7a5245-e377-424a-bc14-6c7c270a69e2
Instance ID                     : uuid:32778404-40e4-4356-8e31-76e39f6b5c80
Producer                        : GPL Ghostscript 9.07; modified using iTextSharp™ 5.4.2 ©2000-2012 1T3XT BVBA (AGPL-version)
Has XFA                         : No
Page Count                      : 57
Creator                         : CubePDF

EXIF Metadata provided by EXIF.tools