Japan Radio Co NKE1130 Marine Radar User Manual JMA 9100 series RADAR Instruction Manual

Japan Radio Co Ltd. Marine Radar JMA 9100 series RADAR Instruction Manual

UserManual.wiki >

Japan Radio Co >

NKE1130 User Manual >

Contents

Users Manual 3

JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS8－3388.4.4 Replacement of LCD Monitor8.4.4.1 Display Unit NCD-4990Do not touch the LCD screen directly with your fingers.Do not touch the AR filter directly with your fingers.Perform the replacement work on a soft cloth to avoid damage to the LCD screen and other parts.[Required tools]•A Phillips screwdriver for 4 mm screws•A Phillips screwdriver for 6 mm screws[Disassembly]1) Remove the tilt fixing handle (standalone type only).2) Tilt up the screen as much as you can (standalone type only).Replacement of LCD monitor must be made by specializedservice personnel. For details, refer to Service Manual.

8－34JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS3) Remove the screws (M6) from the four corners and displace the face cover.4) LRemove the LCD operation circuit cables and remove the face cover.5) Remove six M4 screws. RemoveRemoveRemoveRemove

JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS8－3586) Displace the module and remove the three cables.7) Remove the LCD module.[Assembly]1) Tighten the lower three M4 screws halfway.2) Connect the cables to the LCD module.3) Align the module to the lower three screws and insert it downward.4) Check the positions of the two bosses and ensure that appropriate space is maintained under the LCD module. Tighten the six screws evenly.5) Connect the LCD operation circuit cables and attach the face cover.6) Tighten the screws at the four corners.7) Attach the tilt fixing handle.[Operation Check]1) After completing the replacement procedures, start the system to make sure that images are displayed properly.2) Turn the brightness knob to make sure the brightness can be changed between the minimum and the maximum levels. RemoveTemporary tightening Positions of the two bosses

8－36JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS8.4.5 Replacement of Backup BatteryA coin-cell battery maintains radar system configuration, date, and time information while power off condition. Radar system configuration is saving to non-volatile memory at fixed intervals.8.4.5.1 About the Battery AlarmIf is appeared at the lower-right of the display when start up the radar system, the battery has not enough time left to live. We recommend to replace the battery.If is appeared at the lower-right of the display when start up the radar system, the battery has no time left to live. There is a necessary to replace the battery. In This condition, this radar system is restored configuration information from flash memory and normal operation is available. However, you turned of the radar system before saving to flash memory, the configuration information is maybe lost. In this case, you must setup the configuration again.8.4.5.2 How to Replacement of Backup Battery[Required tools]•A flat tip screwdriver for 6 mm screws•A Phillips screwdriver for 4 mm screws•A flat tip nonconductive screwdriver for 3 mm screwsReplacement of backup battery must be made by specializedservice personnel. For details, refer to Service Manual.About disposal of used battery, refer to Section 10.2.Battery LowBattery Dead

JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS8－378[Disassembly]1) Remove the four fixing screws to remove the cover from the display unit (NCD-4990).（A flat tip screwdriver for 6 mm screws）For standalone type NCD-4990For tabletop type: NDC-1399-92) Remove the cable connected to the radar processing circuit board.The radar processing circuit is the first board from the left.3) Remove the two fixing screws (M4).4) Pull out the board to the front.5) Insert the flat tip nonconductive screwdriver for adjustment or some stick between the battery and the battery holder and lift the battery up.RemoveRemoveRemove

8－38JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS6) Insert the flat tip nonconductive sscrewdriver for adjustment or some stick to the location shown in the figure below and slide the battery sideways to remove the battery. [Assembly]1) Check the polarity of the battery. Make sure that the battery's positive (+) side is facing up.2) Slide the battery sideways into the battery holder.3) Make sure that the battery is inserted fully.[Check Item]1) Check that no error message comes up.2) Check that the system starts up normally.[Notes]

JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS8－398If you installed the battery with the wrong polarity, remove the battery immediately and do not use the same battery again.During the procedures, do not put the battery on any circuit board or conductive item.To dispose of a used battery, follow the instructions provided in Section 10.2 "DISPOSAL OF USED BATTERIES".To disassemble of a used battery, have to use non-conductive tool.

8－40JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS

TROUBLE SHOOTING AND AFTER-SALES SERVICE9.1 FAULT FINDING .....................................................................................9-19.1.1 List of Alarms and other Indications .............................................9-19.1.2 Operation Checking ........................................................................9-59.1.3 Fuse Checking .................................................................................9-59.2 TROUBLE SHOOTING ...........................................................................9-69.2.1 Special Parts ....................................................................................9-79.2.2 Circuit Block to be Repaired ..........................................................9-89.3 AFTER-SALES SERVICE ....................................................................9-149.3.1 Keeping period of maintenance parts .........................................9-149.3.2 When you Request for Repair ......................................................9-149.3.3 Recommended Maintenance ........................................................9-14SECTION 9TROUBLE SHOOTING ANDAFTER-SALES SERVICE

JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDING9－199.1 FAULT FINDINGIn case of semiconductor circuits, it is deemed that there are few cases in which the used semiconductor devices have inferior quality or performance deterioration except due to insufficient design or inspection or by other external and artificial causes. In general, the relatively many causes are disconnection in a high-value resistor due to moisture, a defective variable resistor and poor contact of a switch or relay.Some troubles are caused by defective parts, imperfect adjustment (such as tuning adjustment) or insufficient service (such as poor cable contact). It will also be effective to check and readjust these points.9.1.1 List of Alarms and other IndicationsThe system automatically recognizes an internal alarm and displays the alarm message. If an event which is not trouble but must be reported to the operator occurs, the system notifies the operator of the event.Error message and alarm are displayed in the lower right of the display. For more details refer to page2-31 Alarm.This section gives the list of alarms displayed by the system and other display lists.Table9-1： List of System Error MessageMessage DescriptionTXRX (SSW Off) Scanner: Safety switch OFF.TXRX (AZI) Scanner: BP error.TXRX (HL) Scanner: HL error.TXRX (MHV) Scanner: Modulator's high voltage alarm.TXRX (Data) Scanner: No communication, communication mismatched, checksum error, or collision.TXRX (Heater) Scanner: Magnetron heater voltage error.TXRX (Reverse) Scanner: Reverse rotation.

9－2JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDINGTXRX (Video) Scanner: VIDEO error.TXRX (Trigger) Scanner: TRIGGER error..TXRX (Fan 1) Scanner: FAN 1 error.TXRX (Fan 2) Scanner: FAN 2 error.TXRX (Motor) Scanner: Motor current error.Keyboard (Data) Operation unit: Communication error or checksum error.Keyboard2 (Data) Second operation unit: Communication error or checksum error.GYRO I/F (Data) GYRO I/F: No communication or checksum error.GYRO I/F (GYRO) GYRO I/F: GYRO error (error bit detected).GYRO I/F (Log) GYRO I/F: Log error (error bit detected).GPS (Status) GPS status error.Position (Data) Latitude / longitude data: No communication or data error.Date (Data) Date data: No communication or data error.Speed (Log) 1-axis log: No communication or data error.Speed (2AXW) 2-axis log (speed over water): No communication or data error.Speed (2AXG) 2-axis log (speed over ground): No communication or data error.Speed (GPS) GPS speed: No communication or data error.PROC (Interrupt) Process unit: Interrupt error.PROC (AZI) Process unit: AZI error.PROC (HL) Process unit: HL error.Error during interrupt from ASIC1 to RADAR DSP.ASIC1 to RADAR VIDEO error.PROC (Video) Trigger error.PROC (Trigger) Heading data: No communication or data error.Heading (Data) Water depth: No communication or data error.Depth (Data) Water temperature: No communication or data error.TEMP. (Data) Wind direction/velocity: No communication or data error.Wind (Data) Tidal current: No communication or data error.Current (Data) Rate of Turn: No communication or data error.ROT (Data) Rudder Sensor Angle: No communication or data error.RSA (Data) APB: No communication or data error.Autopilot (Data) LCD monitor: Fan error.Fan (LCD) RADAR Process Unit Interconnection: Fan error.Fan (Power) Power Supply: Fan error.Fan (PROC) Scanner: Safety switch OFF.Table9-2： List of NotificationMessage DescriptionCCRP Changed CCRP is automatic changed.Weather INFO Weather information is received.Copying Display is capturing to file.Table9-1： List of System Error MessageMessage Description

JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDING9－39Set GYRO Requires setting of true bearing.TM Reset Use care of resetting TM.POSN Reset Change the latitude and longitude sentence.Table9-3： List of Target Tracking Alarms and AIS Function Alarmsメッセージ内　　容CPA/TCPA There is a dangerous target.Trial There is a dangerous target, when trial maneuver is active.New Target Acquisition or activation of a target in the automatic acquisition / activation zone.Lost Failure in tracking the target that has been under tracking.Failure in receiving AIS target data for a specified time.REF Target Decrease in the reference target accuracy.MAX Target The maximum number of targets is under acquisition.95% Capacity Over 95% of the maximum number of targets to be tracked.AIS Max Target Maximum number of AIS targets.AIS 95% Capacity Over 95% of the maximum number of AIS targets.AIS ACT MAX Maximum number of AIS targets to be activated.AIS ACT 95% Capacity Over 95% of the maximum number of AIS targets to be activated.TT (Boot) Target tracking unit start failure.TT (Data) The target tracking unit is malfunctioning.AIS (Data) AIS: No communication or communication error.AIS PROC (Data) AIS processing circuit: No communication or communication error.AIS Alarm ***ii. *** is a 3-digit number which is Local Alarm No in the ALR sentence.AIS alarm (Up to 10 alarm messages can be displayed.).Table9-4： List of Route Messages and WarningsMessage DescriptionArrival Arrive at way point.Break Off(WPT) Out of the way point.Approach Approach the route.Cross Track Error Go off the route.Table9-5： List of Operational Error Messages and WarningsMessage DescriptionNo Position Data Mark or line input when the latitude and longitude is invalid.No Heading Data Target tracking operation or TM selection when bearing data is invalid.Out of Range Out of target acquisition range.Table9-2： List of Notification

9－4JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDING Invalid Range TM selection due to TM-disabled range (96 nm).Zooming in a ZOOM-disabled range (0.125 nm).MAX Point Tried to enter navigation information beyond the specified.Can't Transmit Tried to transmit within 5 second after standby or when the transmitter-receiver has any trouble.Invalid Data Tried to enter any data beyond its range.Invalid Connection The operator set performance monitor to on without selecting straight.No Card Card not detected yet.Card Full Card capacity insufficient.Format Card Unformatted card.Invalid Card Invalid card.Read Failed Read failure.Write Failed Write failure.Delete Failed Deletion failure.Format Failed Format failure.Copy Failed Copy failure.Not Allowed General operation error.No Object No object at the cursor-specified position.Slave Mode Operation of a menu for the scanner unit when the slave mode is active.Table9-6： List of Conditions MessagesMessage DescriptionGPS (HDOP) The HDOP level is increased (Decrease in the GPS accuracy.).MON Test Performance monitor is active.Scanner Rotating The scanner is rotating (When transmitter is standby state.).Battery Low battery is weakening.Battery Dead The battery is dead.Table9-7： List of Interswitch Alarms and MessagesMessage DescriptionMaster Range CHG The range of the own display unit has changed due to change in the range of the master display unit.ISW Complete The switchover of the Interswitch ended normally.ISW Busy Access to the ISW menu was made during interswitching.TXRX Standby The scanner unit is in the standby mode.ISW Straight Failed in straight connection when the Interswitch system stops operating.ISW Standby The Interswitch recovered normally.ISW Time Out Failed in switching.ISW Error The interswitch is disabled.Table9-5： List of Operational Error Messages and Warnings

JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDING9－599.1.2 Operation CheckingWhen the system is operating, the operation status (located at the upper right of the screen) is changing pictures.If picture freeze occurred, turn off the system and restart the system. 9.1.3 Fuse CheckingMelted fuses are caused by any clear cause. When a fuse is replaced, it is necessary to check the related circuits even if there is no trouble. In checking, note that there is some dispersion in the fusing characteristics. Table 9-8 shows a list of fuses used in the equipment. Pattern CHG Failed Connection change failed.Connection Masked Inhibition of control / connection is set.Master Standby The master display unit does not transmit any signals.ISW (Data) No communication, data mismatched, or checksum error.Update ISW Software Tried to enter new TXRX function, when interswitch software used old version.Table9-8： Fuse ListLocation Parts# CurrentRating ProtectionCircuit TypeAC/DC Converter F501 10A Motor ST6-10AN1GYRO Interface circuit F1～F4 0.5A GYRO Interface circuitMF60NR250V0.5Table9-7： List of Interswitch Alarms and MessagesOperation Status

9－6JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING9.2 TROUBLE SHOOTINGAs this radar equipment includes complicated circuits, it is necessary to request a specialist engineer for repair or instructions for remedy if any circuit is defective.There are also troubles by the following causes, which should be referred to in checking or repair work.１　Poor Contact in Terminal Board of Inter-Unit Cablesa. Poor contact in terminal boardb. The cable end is not fully connected, that it, contacted with earthed anotherterminal.c. Disconnected cable wire２　Poor Contact of Connector within UnitThis radar equipment is provided with Table 9-9 standardspares.Table9-9： 7ZXRD0025Name Type/Code Shape (mm) In use Spare Parts # LocationFuse MF60NR250V0.5(5ZFGD00006)412 F1～F4 GYRO I/FCMJ-462EFuse ST6-10AN1(5ZFCA00053)13 F501 AC/DC ConverterNBA-5135i30 Φ6.431.8 Φ6.35

JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING9－799.2.1 Special PartsNKE-2103NKE-1125/2254NTG-3225NKE-1130NTG-3230Table9-10： NKE-2103 (JMA-9110-6XA/6XAH、JMA-7110-6XA/6XAH)Parts No. Name Type Manufacture Location CodeV101 Magnetron MAF1565N NJRC Scanner Unit 5VMAA00102A101/A102 Circulator FCX68 Toshiba Scanner Unit 6AJRD00001A301 Diode Limiter NJS6930 NJRC Scanner Unit 5ATBT00006Table9-11： NKE-1125/2254　(JMA-9122-6XAH/9XA/6XAH、JMA-7122-6XA/9XA/6XAH)Parts No. Name Type Manufacture Location CodeV101 Magnetron M1568BS NJRC Scanner Unit 5VMAA00106A101/A102 Circulator NJC3901M NJRC Scanner Unit 5AJBV00007A301 Diode Limiter NJS6930 NJRC Scanner Unit 5ATBT00006Table9-12： NTG-3225　(JMA-9123-7XA/9XA、JMA-7123-7XA/9XA)Parts No. Name Type Manufacture Location CodeV101 Magnetron M1568BS NJRC TransmitterReceiver Unit 5VMAA00106A101/A102 Circulator NJC3901M NJRC TransmitterReceiver Unit 5AJBV00007A301 Diode Limiter NJS6930 NJRC TransmitterReceiver Unit 5ATBT00006Table9-13： NKE-1130　(JMA-9132-SA、JMA-7132-SA)Parts No. Name Type Manufacture Location CodeV101 Magnetron M1555 NJRC Scanner Unit 5VMAA00106A101/A102 Circulator NJC3316 NJRC Scanner Unit 5AJBV00007A301 Diode Limiter NJS6318 NJRC Scanner Unit 5ATBT00006Table9-14： NTG-3230　(JMA-9133-SA、JMA-7133-SA)Parts No. Name Type Manufacture Location CodeV101 Magnetron M1555 NJRC TransmitterReceiver Unit 5VMAA00104A101 Circulator NJC3317 NJRC TransmitterReceiver Unit 5AJBV00009A301 TR Limiter TL378A NJRC TransmitterReceiver Unit 5VLAA00037

9－8JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING9.2.2 Circuit Block to be RepairedTable9-15： Circuit Block to be Repaired (JMA-9110-6XA/6XAH)Location Circuit Block Type RemarksSCANNER UNIT GEARED MOTOR 7BDRD0048 DC brushless motor (commonwith HS)SCANNER UNIT MODULATOR CIRCUIT CME-363 Excluding MagnetronSCANNER UNIT RECEIVER UNIT NRG-610 Including CAE-529-1SCANNER UNIT POWER SUPPLY CIRCUIT CBD-1783SCANNER UNIT ENCODER CHT-71ASCANNER UNIT MOTOR CONTROL POWERSUPPLY CBD-1779SCANNER UNIT FAN 7BFRD0002RADAR PROCESS UNIT RADAR PROCESS CIRCUIT MDLW11900 With mounting bracketRADAR PROCESS UNIT AIS PROCESS CIRCUIT CDC-1325RADAR PROCESS UNIT ARPA PROCESS CIRCUIT CDC-1186DRADAR PROCESS UNIT GYRO I/F CIRCUIT CMJ-462ERADAR PROCESS UNIT TERMINALBOARD CIRCUIT CQD-2097RADAR PROCESS UNIT MOTHERBOARD CIRCUIT CQC-1192RADAR PROCESS UNIT FAN (RPU) 109R0612S4D13RADAR PROCESS UNIT POWER SUPPLY CBD-1661RADAR PROCESS UNIT FAN (PSU) 7BFRD0006OPERATION UNIT OPERATION CIRCUIT A CCK-973OPERATION UNIT OPERATION CIRCUIT B CCK-974OPERATION UNIT OPERATION CIRCUIT D CCK-976OPERATION UNIT TRACKBALL 5EZLY00003OPERATION UNIT LCD PANEL 7WSRD0002A 23.1-inch LCDOPERATION UNIT LCD OPERATION CIRCUIT CCK-972

JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING9－99Table9-16： Circuit Block to be Repaired (JMA-9122-6XA/9XA)Location Circuit Block Type RemarksSCANNER UNIT GEARED MOTOR MDBW10822 For 100/220VACSCANNER UNIT ENCODER CHT-71ASCANNER UNIT AC220V MOTOR DRIVER 7EPRD0034 For 220VACSCANNER UNIT AC100V MOTOR DRIVER 7EPRD0035 For 100VACSCANNER UNIT PERFORMANCE MONITOR NJU-85SCANNER UNIT HEATER CONTROL PART CHG-216 Option (AC100V)SCANNER UNIT BREAK CIRCUIT CFA-253SCANNER UNIT BREAK CONTROL CIRCUIT CCB-655SCANNER UNIT BREAK CIRCUIT A CFA-259SCANNER UNIT BREAK CIRCUIT B CFA-260SCANNER UNIT T/R CONTROL CIRCUIT CMC-1205RSCANNER UNIT MODULATOR UNIT NMA-550 Including CPA-264Including CMB-404Including CFR-229Excluding MagnetronSCANNER UNIT MODULATOR CIRCUIT CPA-264SCANNER UNIT RECEIVER UNIT NRG-162A Including CMA-866ASCANNER UNIT POWER SUPPLY CIRCUIT CBD-1682ASCANNER UNIT RELAY FILTER CIRCUIT CSC-656SCANNER UNIT FAN 7BFRD0002RADAR PROCESS UNIT RADAR PROCESS CIRCUIT MDLW11900 With mounting bracketRADAR PROCESS UNIT AIS PROCESS CIRCUIT CDC-1325RADAR PROCESS UNIT ARPA PROCESS CIRCUIT CDC-1186DRADAR PROCESS UNIT GYRO I/F CIRCUIT CMJ-462ERADAR PROCESS UNIT TERMINALBOARD CIRCUIT CQD-2097RADAR PROCESS UNIT MOTHERBOARD CIRCUIT CQC-1192RADAR PROCESS UNIT FAN (RPU) 109R0612S4D13RADAR PROCESS UNIT POWER SUPPLY CBD-1661RADAR PROCESS UNIT FAN (PSU) 7BFRD0006OPERATION UNIT OPERATION CIRCUIT A CCK-973OPERATION UNIT OPERATION CIRCUIT B CCK-974OPERATION UNIT OPERATION CIRCUIT D CCK-976OPERATION UNIT TRACKBALL 5EZLY00003MONITOR UNIT LCD PANEL 7WSRD0002A 23.1-inch LCDMONITOR UNIT LCD OPERATION CIRCUIT CCK-972

9－10JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTINGTable9-17： Circuit Block to be Repaired (JMA-9122-6XAH)Location Circuit Block Type RemarksSCANNER UNIT GEARED MOTOR 7BDRD0045A For 100/220VACSCANNER UNIT ENCODER CHT-71ASCANNER UNIT MOTOR CONTROL POWERCIRCUIT CBD-1779SCANNER UNIT BREAK CIRCUIT CFA-257SCANNER UNIT PERFORMANCE MONITOR NJU-85SCANNER UNIT HEATER CONTROL PART CHG-216 Option (AC100V)SCANNER UNIT POWER SUPPLY CIRCUIT CBD-1682ASCANNER UNIT T/R CONTROL CIRCUIT CMC-1205RSCANNER UNIT MODULATOR UNIT NMA-550 Including CPA-264Including CMB-404Including CFR-229Excluding MagnetronSCANNER UNIT MODULATOR CIRCUIT CPA-264SCANNER UNIT RECEIVER UNIT NRG-162A Including CMA-866ASCANNER UNIT FAN 7BFRD0002RADAR PROCESS UNIT RADAR PROCESS CIRCUIT MDLW11900 With mounting bracketRADAR PROCESS UNIT AIS PROCESS CIRCUIT CDC-1325RADAR PROCESS UNIT ARPA PROCESS CIRCUIT CDC-1186DRADAR PROCESS UNIT GYRO I/F CIRCUIT CMJ-462ERADAR PROCESS UNIT TERMINALBOARD CIRCUIT CQD-2097RADAR PROCESS UNIT MOTHERBOARD CIRCUIT CQC-1192RADAR PROCESS UNIT FAN (RPU) 109R0612S4D13RADAR PROCESS UNIT POWER SUPPLY CBD-1661RADAR PROCESS UNIT FAN (PSU) 7BFRD0006OPERATION UNIT OPERATION CIRCUIT A CCK-973OPERATION UNIT OPERATION CIRCUIT B CCK-974OPERATION UNIT OPERATION CIRCUIT D CCK-976OPERATION UNIT TRACKBALL 5EZLY00003MONITOR UNIT LCD PANEL 7WSRD0002A 23.1-inch LCDMONITOR UNIT LCD OPERATION CIRCUIT CCK-972

JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING9－119Table9-18： Circuit Block to be Repaired (JMA-9123-7XA/9XA)Location Circuit Block Type RemarksSCANNER UNIT GEARED MOTOR MDBW10822 For 100/220VACSCANNER UNIT ENCODER CHT-71ASCANNER UNIT AC220V MOTOR DRIVER 7EPRD0034 For 220VACSCANNER UNIT AC100V MOTOR DRIVER 7EPRD0035 For 100VACSCANNER UNIT PERFORMANCE MONITOR NJU-85SCANNER UNIT HEATER CONTROL PART CHG-216 Option (AC100V)SCANNER UNIT BREAK CIRCUIT CFA-253SCANNER UNIT BREAK CONTROL CIRCUIT CCB-655SCANNER UNIT BREAK CIRCUIT A CFA-259SCANNER UNIT BREAK CIRCUIT B CFA-260TRANSMITTER RECEIVER UNIT T/R CONTROL CIRCUIT CMC-1205RTRANSMITTER RECEIVER UNIT MODULATOR UNIT NMA-552 Including CPA-264Including CMB-405Including CFR-229Excluding MagnetronTRANSMITTER RECEIVER UNIT MODULATOR CIRCUIT CPA-264TRANSMITTER RECEIVER UNIT RECEIVER UNIT NRG-162A Including CMA-866ATRANSMITTER RECEIVER UNIT POWER SUPPLY CIRCUIT CBD-1682ATRANSMITTER RECEIVER UNIT RELAY FILTER CIRCUIT CSC-656RADAR PROCESS UNIT RADAR PROCESS CIRCUIT MDLW11900 With mounting bracketRADAR PROCESS UNIT AIS PROCESS CIRCUIT CDC-1325RADAR PROCESS UNIT ARPA PROCESS CIRCUIT CDC-1186DRADAR PROCESS UNIT GYRO I/F CIRCUIT CMJ-462ERADAR PROCESS UNIT TERMINALBOARD CIRCUIT CQD-2097RADAR PROCESS UNIT MOTHERBOARD CIRCUIT CQC-1192RADAR PROCESS UNIT FAN (RPU) 109R0612S4D13RADAR PROCESS UNIT POWER SUPPLY CBD-1661RADAR PROCESS UNIT FAN (PSU) 7BFRD0006OPERATION UNIT OPERATION CIRCUIT A CCK-973OPERATION UNIT OPERATION CIRCUIT B CCK-974OPERATION UNIT OPERATION CIRCUIT D CCK-976OPERATION UNIT TRACKBALL 5EZLY00003MONITOR UNIT LCD PANEL 7WSRD0002A 23.1-inch LCDMONITOR UNIT LCD OPERATION CIRCUIT CCK-972

9－12JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTINGTable9-19： Circuit Block to be Repaired (JMA-9132-SA)Location Circuit Block Type RemarksSCANNER UNIT GEARED MOTOR MDBW10823 For 100/220VACSCANNER UNIT ENCODER CHT-71A1SCANNER UNIT AC220V MOTOR DRIVER 7EPRD0034 For 220VACSCANNER UNIT AC100V MOTOR DRIVER 7EPRD0035 For 100VACSCANNER UNIT PERFORMANCE MONITOR NJU-84SCANNER UNIT HEATER CONTROL PART CHG-215 Option (AC100V)SCANNER UNIT BREAK CIRCUIT CFA-255SCANNER UNIT BREAK CONTROL CIRCUIT CCB-655SCANNER UNIT BREAK CIRCUIT A CFA-261SCANNER UNIT BREAK CIRCUIT B CFA-262SCANNER UNIT T/R CONTROL CIRCUIT CMC-1205RSCANNER UNIT MODULATOR UNIT NMA-551 Including CPA-264Including CMB-406Including CFR-229Exluding MagnetronSCANNER UNIT MODULATOR CIRCUIT CPA-264SCANNER UNIT RECEIVER UNIT NRG-229SCANNER UNIT POWER SUPPLY CIRCUIT CBD-1682ASCANNER UNIT RELAY FILTER CIRCUIT CSC-656SCANNER UNIT FAN 7BFRD0002RADAR PROCESS UNIT RADAR PROCESS CIRCUIT MDLW11900 With mounting bracketRADAR PROCESS UNIT AIS PROCESS CIRCUIT CDC-1325RADAR PROCESS UNIT ARPA PROCESS CIRCUIT CDC-1186DRADAR PROCESS UNIT GYRO I/F CIRCUIT CMJ-462ERADAR PROCESS UNIT TERMINALBOARD CIRCUIT CQD-2097RADAR PROCESS UNIT MOTHERBOARD CIRCUIT CQC-1192RADAR PROCESS UNIT FAN (RPU) 109R0612S4D13RADAR PROCESS UNIT POWER SUPPLY CBD-1661RADAR PROCESS UNIT FAN (PSU) 7BFRD0006OPERATION UNIT OPERATION CIRCUIT A CCK-973OPERATION UNIT OPERATION CIRCUIT B CCK-974OPERATION UNIT OPERATION CIRCUIT D CCK-976OPERATION UNIT TRACKBALL 5EZLY00003MONITOR UNIT LCD PANEL 7WSRD0002A 23.1-inch LCDMONITOR UNIT LCD OPERATION CIRCUIT CCK-972

JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING9－139 Table9-20： Circuit Block to be Repaired (JMA-9133-SA)Location Circuit Block Type RemarksSCANNER UNIT GEARED MOTOR MDBW10823 For 100/220VACSCANNER UNIT ENCODER CHT-71A1SCANNER UNIT AC220V MOTOR DRIVER 7EPRD0034 For 220VACSCANNER UNIT AC100V MOTOR DRIVER 7EPRD0035 For 100VACSCANNER UNIT PERFORMANCE MONITOR NJU-84SCANNER UNIT HEATER CONTROL PART CHG-215 Option (AC100V)SCANNER UNIT BREAK CIRCUIT CFA-255SCANNER UNIT BREAK CONTROL CIRCUIT CCB-655SCANNER UNIT BREAK CIRCUIT A CFA-261SCANNER UNIT BREAK CIRCUIT B CFA-262TRANSMITTER RECEIVER UNIT T/R CONTROL CIRCUIT CMC-1205RTRANSMITTER RECEIVER UNIT MODULATOR UNIT NMA-553 Including CPA-264Including CMB-407Including CFR-229Exluding MagnetronTRANSMITTER RECEIVER UNIT MODULATOR CIRCUIT CPA-264TRANSMITTER RECEIVER UNIT RECEIVER UNIT NRG-229TRANSMITTER RECEIVER UNIT POWER SUPPLY CIRCUIT CBD-1682ATRANSMITTER RECEIVER UNIT RELAY FILTER CIRCUIT CSC-656RADAR PROCESS UNIT RADAR PROCESS CIRCUIT MDLW11900 With mounting bracketRADAR PROCESS UNIT AIS PROCESS CIRCUIT CDC-1325RADAR PROCESS UNIT ARPA PROCESS CIRCUIT CDC-1186DRADAR PROCESS UNIT GYRO I/F CIRCUIT CMJ-462ERADAR PROCESS UNIT TERMINALBOARD CIRCUIT CQD-2097RADAR PROCESS UNIT MOTHERBOARD CIRCUIT CQC-1192RADAR PROCESS UNIT FAN (RPU) 109R0612S4D13RADAR PROCESS UNIT POWER SUPPLY CBD-1661RADAR PROCESS UNIT FAN (PSU) 7BFRD0006OPERATION UNIT OPERATION CIRCUIT A CCK-973OPERATION UNIT OPERATION CIRCUIT B CCK-974OPERATION UNIT OPERATION CIRCUIT D CCK-976OPERATION UNIT TRACKBALL 5EZLY00003MONITOR UNIT LCD PANEL 7WSRD0002A 23.1-inch LCDMONITOR UNIT LCD OPERATION CIRCUIT CCK-972

9－14JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.3 AFTER-SALES SERVICE9.3 AFTER-SALES SERVICE9.3.1 Keeping period of maintenance partsKeeping period of maintenance parts is ten years from the production is discontinued.9.3.2 When you Request for Repair If you suppose the product may be out of order, read the description in Section 9 carefully and check the suspected point again.If it is still out of order, you are recommended to stop operation of the equipment and consult with the dealer from whom you purchased the product, or our branch office in your country or district, the sales department in our main office in Tokyo.Repair within the Warranty Period If any failure occurs in the product during its normal operation in accordance with the instruction manual, the dealer or JRC will repair free of charge. In case that any failure is caused due to misuse, faulty operation, negligence or force major such as natural disaster and fire, the product will be repaired with charges.Repair after the Warranty Period If any defective function of the product is recoverable by repair, the repair of it will be made at your own charge upon your request.Necessary Information for Repair •Product name, model, manufacturing date and serial number•Trouble conditions (as detailed as possible. Refer to "Radar Failure Check List" on page 9-15•Name of company/organization, address and telephone number9.3.3 Recommended MaintenanceThe performance of the product may deteriorate due to the secular change of the parts used in it, though such deterioration depends upon the conditions of operation. So checkup and maintenance is recommendable for the product in addition to your daily care.For maintenance, consult with the near-by dealer or our sales department.Such maintenance will be made with charges.For further details of after-sale service, contact the JRC Offices.

JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.3 AFTER-SALES SERVICE9－159Radar Failure Check ListCheck the following items in the order of the number, and check the applicable answer between YES or NO. If the item cannot be determined as YES or NO, explain in detail in the item (18), others.iWhen placing an order for repair of the product, it is requested that you couldconfirm the check items and fill the results and sent the sheet to our contact.If there is any unclear items, contact the ship on which the product isinstalled, and give the correct information on the product.Ship name: 　Phone: 　Fax:iRadar general model name :JMA-i. Write the full model name correctly　iSerial No. :No. Check Item Result(1) Power can be turned on. (The lamp on the Operation unit is lit) YES NO(2)ii. If result is NO, then check the fuse. (Refer to Section 9.1.2 "Operation Checking" and Section 9.2 "TROUBLESHOOTING")A few minutes after powering-on, it will become standby status. YES NO(3)iWhen powering-on (or TX ON), LCD monitor something is lit. YES NO(4)i,ii The antenna rotates at the transmission (TX) ON. YES NO(5)i,ii Current is supplied to the magnetron. (Refer to the instruction manual) YES NO(6)iiii. Check these items while transmission is ON.Turning is enabled. (Check with the range of 6 NM or more) YES NO(7)ii Fixed marker is displayed. YES NO(8)ii VRM is displayed. YES NO(9)ii While noise is displayed while set at SEA and RAIN minimum, GAINmaximum, IR-OFF and range 48 NM. YES NO(10)ii Target reflection echo is displayed. YES NO(11)ii Sensitivity of reflection echo is normal. YES NO(12)ii EBL is displayed. YES NO(13)ii Cursor mark moves. YES NO(14)ii,iiiiii. Functions mentioned in the items (14), (15) and (17) may be optional, answer is not necessary.GYRO course can be set and normally displayed. YES NO(15)ii,iii LOG speed can be normally displayed. YES NO(16)ii Target tracking function works normally. YES NO(17)ii,iii If equipped with an interswitch, when switching from the straight mode (II) to(X), the failures (items marked NO) in the above (1) to (16), are switched overto the other unit.YES NO（18）Others (Error message, etc. )

9－16JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.3 AFTER-SALES SERVICE

DISPOSAL10.1 DISPOSAL OF THE UNIT ....................................................................10-110.2 DISPOSAL OF USED BATTERIES .....................................................10-110.3 DISPOSAL OF USED MAGNETRON ..................................................10-210.4 DISPOSAL OF TR-TUBE .....................................................................10-210.5 ABOUT THE CHINA ROHS .................................................................10-3SECTION 10DISPOSAL

JMA-9100 Instruction Manual > 10.DISPOSAL > 10.1 DISPOSAL OF THE UNIT10－11010.1 DISPOSAL OF THE UNITWhen disposing of this unit, be sure to follow the local laws and regulations for the place of disposal. 10.2 DISPOSAL OF USED BATTERIESIn this unit, Lithium batteries are used for the following parts:Radar Processing circuit (CDC-1324): BT1 (Maxell: CR2032)•Do not store used lithium batteries. Dispose of them in accordance with regulations of local government.•When disposing of used lithium batteries be sure to insulate the batteries by taping the terminals. For disposal of batteries, be sure to follow the local laws and regulations. For detail, consult with the dealer you purchased the product our business office, or local government. When disposing of used lithium batteries, be sure to insulate the batteries by taping the terminals.Otherwise, heat generation, explosion or a fire may occur.+ -+ -

JMA-9100 Instruction Manual > 10.DISPOSAL > 10.3 DISPOSAL OF USED MAGNETRON10－21010.3 DISPOSAL OF USED MAGNETRONMagnetron is used in the Scanner （NKE－2103/2254/1125/1130）and Transmitter Receiver Unit (NTG-3225/3230).•When the magnetron is replaced with a new one, return the used magnetron to our dealer or business office.For detail, consult with our dealer or business office. 10.4 DISPOSAL OF TR-TUBEIn the case that either mark shown in Fig 10-1 is on the expired TR-tube, Radioisotopes are in the TR-tube.•Disposal of TR-tube with these marks must be done in accordance with the laws and regulations of the pertaining country. For detail, consult with our dealer or business office.•Radiation from TR-tube has no effect on the human body.•Don't take apart TR-tube.Fig 10-1: Radioisotopes Marks

JMA-9100 Instruction Manual > 10.DISPOSAL > 10.5 ABOUT THE CHINA ROHS10－31010.5 ABOUT THE CHINA ROHS 形式名(Type): JMA-9100 Series, JMA-7100Series 名称(Name): RADAR铅汞镉六价铬多溴联苯多溴二苯醚(Pb) (Hg) (Cd) (Cr6+) (PBB) (PBDE) 雷达天线单元 (Scanner Unit)××○××× 收发信单元 (Transmitter-receiver Unit)×××××× 主船内装置 (Inboard Unit) ・显示装置 (Display Unit) ・键盘装置 (OperationUnit) ・信号处理装置 (RADAR Process Unit)×××××× 外部设备 (Peripherals) ・选择 (Options) ・电线类 (Cables) ・手册 (Documennts)××××××有毒有害物质或元素的名称及含量(Names & Content of toxic and hazardous substances or elements）(Toxic and Hazardous Substances and Elements) ×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T11363-2006 标准规定的限量要求。　　(Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T 11363-2006.) ○：表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11306-2006 标准规定的限量要求以下。 (Indicates that this toxic, or hazardous substance contained in all of the homogeneous materials for this part is below the requirement in SJ/T11363-2006.)部件名称(Part name) 有毒有害物质或元素

10－4JMA-9100 Instruction Manual > 10.DISPOSAL > 10.5 ABOUT THE CHINA ROHS

SPECIFICATION11.1 JMA-9133-SA TYPE RADAR ...............................................................11-111.2 JMA-9132-SA TYPE RADAR............................................................... 11-211.3 JMA-9123-7XA/9XA TYPE RADAR ....................................................11-311.4 JMA-9122-6XA/9XA TYPE RADAR ....................................................11-411.5 JMA-9122-6XAH TYPE RADAR .........................................................11-511.6 JMA-9110-6XA TYPE RADAR ............................................................11-611.7 JMA-9110-6XAH TYPE RADAR .........................................................11-711.8 SCANNER UNIT (NKE-1139) ...............................................................11-811.9 SCANNER UNIT (NKE-1130) ...............................................................11-911.10 SCANNER UNIT (NKE-1129-7/9) ......................................................11-1011.11 SCANNER UNIT (NKE-1125-6/9) .......................................................11-1111.12 SCANNER UNIT (NKE-2254-6HS) .....................................................11-1211.13 SCANNER UNIT (NKE-2103-6) ..........................................................11-1311.14 SCANNER UNIT (NKE-2103-6HS) .....................................................11-1411.15 TRANSMITTER RECEIVER UNIT (NTG-3230) .................................11-1511.16 TRANSMITTER RECEIVER UNIT (NTG-3225) .................................11-1611.17 DISPLAY UNIT (NCD-4990) ...............................................................11-17SECTION 11SPECIFICATION

11.18 Target Tracking Function .................................................................11-2011.19 AIS FUNCTION ...................................................................................11-2111.20 PERFORMANCE MONITOR (NJU-84) ..............................................11-2211.21 PERFORMANCE MONITOR (NJU-85) ..............................................11-2211.22 AC-DC CONVERTER (NBA-5135) .....................................................11-22

JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.1 JMA-9133-SA TYPE RADAR11 －11111.1 JMA-9133-SA TYPE RADARGENERAL SPECIFICATIONClass of emission P0NDisplay Color Raster ScanScreen 23.1inch LCD (Effective diameter of Radar: more than 320mm)Range Scale 0.125、0.25、0.5、0.75、1.5、3、6、12、24、48、96NMRange Resolution less than 30mMinimum Detection Range less than 40mBearing Accuracy less than 1°Bearing Indication Relative motion mode : N-UP, C-UP and H-UPTrue motion mode : N-UP and C-UPAmbient Condition Temperature SCANNER UNIT -25 to +55℃ (Storage -25 to +70℃) Other Unit -15 to +55℃Relative humidity 93% at +40℃Vibration 2 to 13.2Hz　 Amplitude +/-1mm +/-10%13.2 to 100Hz　Acceleration 7m/s2Power Supply Input AC100 to 115V, 50/60Hz, 1φ orAC220 to 240V, 50/60Hz, 1φPower Consumption Approx.400VA typicalApprox. 2000VA at Maximum wind speedPS Voltage Fluctuation +/-10% (at the maximum cable length)Pre Heating Time Within 4 minuteFrom STBY to TX Within 5 sec.SCANNER UNIT (NKE-1139)See 11.8TRANSMITTER RECEIVER UNIT (NTG-3230)See 11.15DISPLAY UNIT (NCD-4990)See 11.17PERFORMANCE MONITOR (NJU-84)See 11.20OPTIONScanner with Deicing Heater NKE-1139-D (Only heater collar)Radar Inter switch NQE-3141-2A (Maximum 2 Radars)NQE-3141-4A (Maximum 4 Radars)DISPLAY UNIT (Desktop type) NCD-4990TMaximum Cable LengthSCANNER UNIT toTRANSMITTER RECEIVER UNIT 30mDISPLAY UNIT toTRANSMITTER RECEIVER UNIT 35mSAFE DISTANCE FOR STANDARD COMPASSSCANNER UNIT 1.4mTRANSMITTER RECEIVER UNIT 3.9mDISPLAY UNIT 4.0m

11 －2JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.2 JMA-9132-SA TYPE RADAR11.2 JMA-9132-SA TYPE RADAR GENERAL SPECIFICATIONClass of emission P0NDisplay Color Raster ScanScreen 23.1inch LCD (Effective diameter of Radar: more than 320mm)Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NMRange Resolution less than 30mMinimum Detection Range less than 40mBearing Accuracy less than 1°Bearing Indication Relative motion mode : N-UP, C-UP and H-UPTrue motion mode : N-UP and C-UPAmbient Condition Temperature SCANNER UNIT -25 to +55℃ (Storage -25 to +70℃) Other Unit -15 to +55℃Relative humidity 93% at +40℃Vibration 2 to 13.2Hz　 Amplitude +/-1mm +/-10%13.2 to 100Hz　Acceleration 7m/s2Power Supply Input AC100 to 115V, 50/60Hz, 1φ orAC220 to 240V, 50/60Hz, 1φPower Consumption Approx.400VA typicalApprox. 2000VA at Maximum wind speedPS Voltage Fluctuation +/-10% (at the maximum cable length)Pre Heating Time Within 4 minuteFrom STBY to TX Within 5 sec.SCANNER UNIT (NKE-1130)See 11.9DISPLAY UNIT (NCD-4990)See 11.17PERFORMANCE MONITOR (NJU-84)See 11.20OPTIONScanner with Deicing Heater NKE-1139-D (Only heater collar)Radar Inter switch NQE-3141-2A (Maximum 2 Radars)NQE-3141-4A (Maximum 4 Radars)DISPLAY UNIT (Desktop type) NCD-4990TMaximum Cable LengthSCANNER UNIT toTRANSMITTER RECEIVER UNIT 65mSAFE DISTANCE FOR STANDARD COMPASSSCANNER UNIT 5.1mDISPLAY UNIT 4.0m

JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.3 JMA-9123-7XA/9XA TYPE RADAR11 －31111.3 JMA-9123-7XA/9XA TYPE RADAR GENERAL SPECIFICATIONClass of emission P0NDisplay Color Raster ScanScreen 23.1inch LCD (Effective diameter of Radar: more than 320mm)Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NMRange Resolution less than 30mMinimum Detection Range less than 40mBearing Accuracy less than 1°Bearing Indication Relative motion mode : N-UP, C-UP and H-UPTrue motion mode : N-UP and C-UPAmbient Condition Temperature SCANNER UNIT -25 to +55℃ (Storage -25 to +70℃) Other Unit -15 to +55℃Relative humidity 93% at +40℃Vibration 2 to 13.2Hz　 Amplitude +/-1mm +/-10%13.2 to 100Hz　Acceleration 7m/s2Power Supply Input AC100 to 115V, 50/60Hz, 1φ orAC220 to 240V, 50/60Hz, 1φPower Consumption Approx.350VA typicalApprox. 1700VA at Maximum wind speedPS Voltage Fluctuation +/-10% (at the maximum cable length)Pre Heating Time Within 4 minuteFrom STBY to TX Within 5 sec.SCANNER UNIT (NKE-1129-7/9)See 11.10TRANSMITTER RECEIVER UNIT (NTG-3225)See 11.16DISPLAY UNIT (NCD-4990)See 11.17PERFORMANCE MONITOR (NJU-85)See 11.21OPTIONScanner with Deicing Heater NKE-1139-D (Only heater collar)Radar Inter switch NQE-3141-2A (Maximum 2 Radars)NQE-3141-4A (Maximum 4 Radars)DISPLAY UNIT (Desktop type) NCD-4990TMaximum Cable LengthSCANNER UNIT toTRANSMITTER RECEIVER UNIT 30mDISPLAY UNIT toTRANSMITTER RECEIVER UNIT 35mSAFE DISTANCE FOR STANDARD COMPASSSCANNER UNIT 1.05mTRANSMITTER RECEIVER UNIT 2.8mDISPLAY UNIT 4.0m

11 －4JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.4 JMA-9122-6XA/9XA TYPE RADAR11.4 JMA-9122-6XA/9XA TYPE RADARGENERAL SPECIFICATIONClass of emission P0NDisplay Color Raster ScanScreen 23.1inch LCD (Effective diameter of Radar: more than 320mm)Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NMRange Resolution less than 30mMinimum Detection Range less than 40mBearing Accuracy less than 1°Bearing Indication Relative motion mode : N-UP, C-UP and H-UPTrue motion mode : N-UP and C-UPAmbient Condition Temperature SCANNER UNIT -25 to +55℃ (Storage -25 to +70℃) Other Unit -15 to +55℃Relative humidity 93% at +40℃Vibration 2 to 13.2Hz　 Amplitude +/-1mm +/-10%13.2 to 100Hz　Acceleration 7m/s2Power Supply Input AC100 to 115V, 50/60Hz, 1φ orAC220 to 240V, 50/60Hz, 1φPower Consumption Approx.350VA typicalApprox. 1700VA at Maximum wind speedPS Voltage Fluctuation +/-10% (at the maximum cable length)Pre Heating Time Within 4 minuteFrom STBY to TX Within 5 sec.SCANNER UNIT (NKE-1125-6/9)See 11.11DISPLAY UNIT (NCD-4990)See 11.17PERFORMANCE MONITOR (NJU-85)See 11.21OPTIONScanner with Deicing Heater NKE-1139-D (Only heater collar)Radar Inter switch NQE-3141-2A (Maximum 2 Radars)NQE-3141-4A (Maximum 4 Radars)DISPLAY UNIT (Desktop type) NCD-4990TMaximum Cable LengthSCANNER UNIT toTRANSMITTER RECEIVER UNIT 65mSAFE DISTANCE FOR STANDARD COMPASSSCANNER UNIT 2.4mDISPLAY UNIT 4.0m

JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.5 JMA-9122-6XAH TYPE RADAR11 －51111.5 JMA-9122-6XAH TYPE RADAR GENERAL SPECIFICATIONClass of emission P0NDisplay Color Raster ScanScreen 23.1inch LCD (Effective diameter of Radar: more than 320mm)Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NMRange Resolution less than 30mMinimum Detection Range less than 40mBearing Accuracy less than 1°Bearing Indication Relative motion mode : N-UP, C-UP and H-UPTrue motion mode : N-UP and C-UPAmbient Condition Temperature SCANNER UNIT -25 to +55℃ (Storage -25 to +70℃) Other Unit -15 to +55℃Relative humidity 93% at +40℃Vibration 2 to 13.2Hz　 Amplitude +/-1mm +/-10%13.2 to 100Hz　Acceleration 7m/s2Power Supply Input AC100 to 115V, 50/60Hz, 1φ orAC220 to 240V, 50/60Hz, 1φPower Consumption Approx.350VA typicalApprox. 1000VA at Maximum wind speedPS Voltage Fluctuation +/-10% (at the maximum cable length)Pre Heating Time Within 4 minuteFrom STBY to TX Within 5 sec.SCANNER UNIT (NKE-2254-6HS)See 11.11DISPLAY UNIT (NCD-4990)See 11.17PERFORMANCE MONITOR (NJU-85)See 11.21AC-DC CONVERTER (NBA-5135)See 11.22OPTIONScanner with Deicing Heater NoneRadar Inter switch NQE-3141-2A (Maximum 2 Radars)NQE-3141-4A (Maximum 4 Radars)DISPLAY UNIT (Desktop type) NCD-4990TMaximum Cable LengthSCANNER UNIT toTRANSMITTER RECEIVER UNIT 65mSAFE DISTANCE FOR STANDARD COMPASSSCANNER UNIT 2.4mDISPLAY UNIT 4.0m

11 －6JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.6 JMA-9110-6XA TYPE RADAR11.6 JMA-9110-6XA TYPE RADAR GENERAL SPECIFICATIONClass of emission P0NDisplay Color Raster ScanScreen 23.1inch LCD (Effective diameter of Radar: more than 320mm)Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NMRange Resolution less than 30mMinimum Detection Range less than 40mBearing Accuracy less than 1°Bearing Indication Relative motion mode : N-UP, C-UP and H-UPTrue motion mode : N-UP and C-UPAmbient Condition Temperature SCANNER UNIT -25 to +55℃ (Storage -25 to +70℃) Other Unit -15 to +55℃Relative humidity 93% at +40℃Vibration 2 to 13.2Hz　 Amplitude +/-1mm +/-10%13.2 to 100Hz　Acceleration 7m/s2Power Supply Input AC100 to 115V, 50/60Hz, 1φ orAC220 to 240V, 50/60Hz, 1φPower Consumption Approx.350VA typicalApprox. 1000VA at Maximum wind speedPS Voltage Fluctuation +/-10% (at the maximum cable length)Pre Heating Time Within 4 minuteFrom STBY to TX Within 5 sec.SCANNER UNIT (NKE-2103-6)See 11.13DISPLAY UNIT (NCD-4990)See 11.17PERFORMANCE MONITOR (NJU-85)See 11.21AC-DC CONVERTER (NBA-5135)See 11.22OPTIONScanner with Deicing Heater NoneRadar Inter switch NQE-3141-2A (Maximum 2 Radars)NQE-3141-4A (Maximum 4 Radars)DISPLAY UNIT (Desktop type) NCD-4990TMaximum Cable LengthSCANNER UNIT toTRANSMITTER RECEIVER UNIT 65mSAFE DISTANCE FOR STANDARD COMPASSSCANNER UNIT 2.4mDISPLAY UNIT 4.0m

JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.7 JMA-9110-6XAH TYPE RADAR11 －71111.7 JMA-9110-6XAH TYPE RADARGENERAL SPECIFICATIONClass of emission P0NDisplay Color Raster ScanScreen 23.1inch LCD (Effective diameter of Radar: more than 320mm)Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NMRange Resolution less than 30mMinimum Detection Range less than 40mBearing Accuracy less than 1°Bearing Indication Relative motion mode : N-UP, C-UP and H-UPTrue motion mode : N-UP and C-UPAmbient Condition Temperature SCANNER UNIT -25 to +55℃ (Storage -25 to +70℃) Other Unit -15 to +55℃Relative humidity 93% at +40℃Vibration 2 to 13.2Hz　 Amplitude +/-1mm +/-10%13.2 to 100Hz　Acceleration 7m/s2Power Supply Input AC100 to 115V, 50/60Hz, 1φ orAC220 to 240V, 50/60Hz, 1φPower Consumption Approx.350VA typicalApprox. 1000VA at Maximum wind speedPS Voltage Fluctuation +/-10% (at the maximum cable length)Pre Heating Time Within 4 minuteFrom STBY to TX Within 5 sec.SCANNER UNIT (NKE-2103-6HS)See 11.14DISPLAY UNIT (NCD-4990)See 11.17PERFORMANCE MONITOR (NJU-85)See 11.21AC-DC CONVERTER (NBA-5135)See 11.22OPTIONScanner with Deicing Heater NoneRadar Inter switch NQE-3141-2A (Maximum 2 Radars)NQE-3141-4A (Maximum 4 Radars)DISPLAY UNIT (Desktop type) NCD-4990TMaximum Cable LengthSCANNER UNIT～DISPLAYUNIT 65mSAFE DISTANCE FOR STANDARD COMPASSSCANNER UNIT 2.4mDISPLAY UNIT 4.0m

11 －8JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.8 SCANNER UNIT (NKE-1139)11.8 SCANNER UNIT (NKE-1139) SCANNER UNIT　NKE-1139Dimension Height 791 x Swing Circle 4000 (mm)Mass Approx.150kgPolarization HorizontalDirectional Characteristics Horizontal beam widthVertical beam widthSide lobe Level: 1.9°: 25°: below -26dB (within +/-10°): below -30dB (outside +/-10°)Revolution Approx.24rpmPower Supply for Motor AC100 - 115V、50/60Hz、1φ　orAC220 - 240V、50/60Hz、1φ　Maximum Wind Velocity 51.5m/s (100knots)

JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.9 SCANNER UNIT (NKE-1130)11 －91111.9 SCANNER UNIT (NKE-1130) SCANNER UNIT　NKE-1130Dimension Height 791 x Swing Circle 4000 (mm)Mass Approx.180kgPolarization HorizontalDirectional Characteristics Horizontal beam widthVertical beam widthSide lobe Level: 1.9°: 25°: below -26dB (within +/-10°): below -30dB (outside +/-10°)Revolution Approx.24rpmPower Supply for Motor AC100 - 115V、50/60Hz、1φ orAC220 - 240V、50/60Hz、1φMaximum Wind Velocity 51.5m/s (100knots)Transmitting Frequency 3050±20MHzTransmitting Power 30kWTransmitting Tube Magnetron[M1555]TX Pulse width / RepetitionFrequency SP1：0.07μs/2250HzMP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz0.125、0.25、0.5NM ：SP1 0.75NM ：SP1/MP1 1.5NM ：SP1/MP1/MP2/MP3 3NM ：MP1/MP2/MP3/LP1 6NM ：MP1/MP2/MP3/LP1/LP2 12NM ：MP1/MP2/MP3/LP1/LP2 24NM ：MP3/LP1/LP2 48NM ：LP2 96NM ：LP3Modulator Solid State Modulator CircuitDuplexer Circulator + Diode LimiterFront End Module Built-inIntermediate Frequency Amplifier Intermediate FrequencyBand WidthGainAmplifying Characteristics: 60MHz: 25/8/3MHz: more than 90dB: Logarithmic AmplifierOverall Noise Figure 7.5dB ( Typical)Tuning Manual/AUTO

11 －10JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.10 SCANNER UNIT (NKE-1129-7/9)11.10 SCANNER UNIT (NKE-1129-7/9) SCANNER UNIT　NKE-1129-7/9Dimension 7ft Height 536 x Swing Circle 2270 (mm)9ft Height 536 x Swing Circle 2825 (mm)Mass 7ft Approx.51kg9ft Approx.53kgPolarization HorizontalDirectional Characteristics Horizontal beam widthVertical beam widthSide lobe Level: 1.0° (7ft): 0.8° (9ft): 20°: below -26dB (within +/-10°): below -30dB (outside +/-10°)Revolution Approx.24rpmPower Supply for Motor AC100 - 115V、50/60Hz、1φ　orAC220 - 240V、50/60Hz、1φ　Maximum Wind Velocity 51.5m/s (100knots)

JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.11 SCANNER UNIT (NKE-1125-6/9)11 －111111.11 SCANNER UNIT (NKE-1125-6/9) SCANNER UNIT　NKE-1125-6/9Dimension 6ft Height 536 x Swing Circle 1910 (mm)9ft Height 536 x Swing Circle 2825 (mm)Mass 6ft Approx. 55kg9ft Approx. 60kgPolarization HorizontalDirectional Characteristics Horizontal beam widthVertical beam widthSide lobe Level: 1.2° (6ft): 0.8° (9ft): 20°: below -26dB (within +/-10°): below -30dB (outside +/-10°)Revolution Approx.24rpmPower Supply for Motor AC100 - 115V、50/60Hz、1φ orAC220 - 240V、50/60Hz、1φMaximum Wind Velocity 51.5m/s (100knots)Transmitting Frequency 9410±30MHzTransmitting Power 25kWTransmitting Tube Magnetron[M1568BS]TX Pulse width / RepetitionFrequency SP1：0.07μs/2250HzMP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz0.125、0.25、0.5NM ：SP1 0.75NM ：SP1/MP1 1.5NM ：SP1/MP1/MP2/MP3 3NM ：MP1/MP2/MP3/LP1 6NM ：MP1/MP2/MP3/LP1/LP2 12NM ：MP1/MP2/MP3/LP1/LP2 24NM ：MP3/LP1/LP2 48NM ：LP2 96NM ：LP3Modulator Solid State Modulator CircuitDuplexer Circulator + Diode LimiterFront End Module Built-inIntermediate Frequency Amplifier Intermediate FrequencyBand WidthGainAmplifying Characteristics: 60MHz: 25/8/3MHz: more than 90dB: Logarithmic AmplifierOverall Noise Figure 7.5dB ( Typical)Tuning Manual/AUTO

11 －12JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.12 SCANNER UNIT (NKE-2254-6HS)11.12 SCANNER UNIT (NKE-2254-6HS) SCANNER UNIT　NKE-2254-6HSDimension Height 536 x Swing Circle 1910 (mm)Mass Approx. 55kgPolarization HorizontalDirectional Characteristics Horizontal beam widthVertical beam widthSide lobe Level: 1.2°: 20°: below -26dB (within +/-10°): below -30dB (outside +/-10°)Revolution Approx.24rpmPower Supply for Motor DC24VMaximum Wind Velocity 51.5m/s (100knots)Transmitting Frequency 9410±30MHzTransmitting Power 25kWTransmitting Tube Magnetron[M1568BS]TX Pulse width / RepetitionFrequency SP1：0.07μs/2250HzMP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz0.125、0.25、0.5NM ：SP1 0.75NM ：SP1/MP1 1.5NM ：SP1/MP1/MP2/MP3 3NM ：MP1/MP2/MP3/LP1 6NM ：MP1/MP2/MP3/LP1/LP2 12NM ：MP1/MP2/MP3/LP1/LP2 24NM ：MP3/LP1/LP2 48NM ：LP2 96NM ：LP3Modulator Solid State Modulator CircuitDuplexer Circulator + Diode LimiterFront End Module Built-inIntermediate Frequency Amplifier Intermediate FrequencyBand WidthGainAmplifying Characteristics: 60MHz: 25/8/3MHz: more than 90dB: Logarithmic AmplifierOverall Noise Figure 7.5dB ( Typical)Tuning Manual/AUTO

JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.13 SCANNER UNIT (NKE-2103-6)11 －131111.13 SCANNER UNIT (NKE-2103-6) SCANNER UNIT　NKE-2103-6HSDimension Height 458 x Swing Circle 1910 (mm)Mass Approx. 40kgPolarization HorizontalDirectional Characteristics Horizontal beam widthVertical beam widthSide lobe Level: 1.2°: 20°: below -26dB (within +/-10°): below -30dB (outside +/-10°)Revolution Approx.24rpmPower Supply for Motor DC24VMaximum Wind Velocity 51.5m/s (100knots)Transmitting Frequency 9410±30MHzTransmitting Power 10kWTransmitting Tube Magnetron[MAF1565N]TX Pulse width / RepetitionFrequency SP1：0.08μs/2250HzMP1：0.25μs/1700Hz MP2：0.5μs/1200HzLP1：0.8μs/750Hz、LP2：1.0μs/650Hz0.125、0.25、0.5NM ：SP1 0.75NM ：SP1/MP1 1.5NM ：SP1/MP1/MP2 3NM ：MP1/MP2LP1 6NM ：MP1/MP2/LP1/LP2 12NM ：MP1/MP2/LP1/LP2 24NM ：MP2/LP1/LP2 48NM ：LP2 96NM ：LP2Modulator Solid State Modulator CircuitDuplexer Circulator + Diode LimiterFront End Module Built-inIntermediate Frequency Amplifier Intermediate FrequencyBand WidthGainAmplifying Characteristics: 60MHz: 20/6/3MHz: more than 90dB: Logarithmic AmplifierOverall Noise Figure 7.5dB ( Typical)Tuning Manual/AUTO

11 －14JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.14 SCANNER UNIT (NKE-2103-6HS)11.14 SCANNER UNIT (NKE-2103-6HS) SCANNER UNIT　NKE-2103-6HSDimension Height 458 x Swing Circle 1910 (mm)Mass Approx. 40kgPolarization HorizontalDirectional Characteristics Horizontal beam widthVertical beam widthSide lobe Level: 1.2°: 20°: below -26dB (within +/-10°): below -30dB (outside +/-10°)Revolution Approx.24rpmPower Supply for Motor DC24VMaximum Wind Velocity 51.5m/s (100knots)Transmitting Frequency 9410±30MHzTransmitting Power 10kWTransmitting Tube Magnetron[MAF1565N]TX Pulse width / RepetitionFrequency SP1：0.08μs/2250HzMP1：0.25μs/1700Hz MP2：0.5μs/1200HzLP1：0.8μs/750Hz、LP2：1.0μs/650Hz0.125、0.25、0.5NM ：SP1 0.75NM ：SP1/MP1 1.5NM ：SP1/MP1/MP2 3NM ：MP1/MP2LP1 6NM ：MP1/MP2/LP1/LP2 12NM ：MP1/MP2/LP1/LP2 24NM ：MP2/LP1/LP2 48NM ：LP2 96NM ：LP2Modulator Solid State Modulator CircuitDuplexer Circulator + Diode LimiterFront End Module Built-inIntermediate Frequency Amplifier Intermediate FrequencyBand WidthGainAmplifying Characteristics: 60MHz: 20/6/3MHz: more than 90dB: Logarithmic AmplifierOverall Noise Figure 7.5dB ( Typical)Tuning Manual/AUTO

JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.15 TRANSMITTER RECEIVER UNIT (NTG-3230)11 －151111.15 TRANSMITTER RECEIVER UNIT (NTG-3230) SCANNER UNIT　NTG-3230Dimension :Width 615 x Depth 365 x Height 615 (mm)構造 Wall Mount, Drip ProofMass Approx.33kgTransmitting Frequency 3050±20MHzTransmitting Power 30kWTransmitting Tube Magnetron [M1555]TX Pulse width / RepetitionFrequency SP1：0.07μs/2250HzMP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz0.125、0.25、0.5NM ：SP1 0.75NM ：SP1/MP1 1.5NM ：SP1/MP1/MP2/MP3 3NM ：MP1/MP2/MP3/LP1 6NM ：MP1/MP2/MP3/LP1/LP2 12NM ：MP1/MP2/MP3/LP1/LP2 24NM ：MP3/LP1/LP2 48NM ：LP2 96NM ：LP3Modulator Solid State Modulator CircuitDuplexer Circulator + TRHPLFront End Module Built-inIntermediate Frequency Amplifier Intermediate FrequencyBand WidthGainAmplifying Characteristics: 60MHz: 25/8/3MHz: more than 90dB: Logarithmic AmplifierOverall Noise Figure 7.5dB ( Typical)Tuning Manual/AUTO

11 －16JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.16 TRANSMITTER RECEIVER UNIT (NTG-3225)11.16 TRANSMITTER RECEIVER UNIT (NTG-3225) SCANNER UNIT　NTG-3225Dimension :Width 460 x Depth 227 x Height 461 (mm)構造 Wall Mount, Drip ProofMass Approx.15kgTransmitting Frequency 9410±30MHzTransmitting Power 25kWTransmitting Tube Magnetron[M1568BS]TX Pulse width / RepetitionFrequency SP1：0.07μs/2250HzMP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz0.125、0.25、0.5NM ：SP1 0.75NM ：SP1/MP1 1.5NM ：SP1/MP1/MP2/MP3 3NM ：MP1/MP2/MP3/LP1 6NM ：MP1/MP2/MP3/LP1/LP2 12NM ：MP1/MP2/MP3/LP1/LP2 24NM ：MP3/LP1/LP2 48NM ：LP2 96NM ：LP3Modulator Solid State Modulator CircuitDuplexer Circulator + Diode LimiterFront End Module Built-inIntermediate Frequency Amplifier Intermediate FrequencyBand WidthGainAmplifying Characteristics: 60MHz: 25/8/3MHz: more than 90dB: Logarithmic AmplifierOverall Noise Figure 7.5dB ( Typical)Tuning Manual/AUTO

JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.17 DISPLAY UNIT (NCD-4990)11 －171111.17 DISPLAY UNIT (NCD-4990)DISPLAY UNIT NCD-4990Dimension Width 700 x Depth 850 x Height 1100 (mm)Structure Self-Standing, Drip ProofMass Approx.130kg Screen 23.1inch Color LCD (Effective Diameter, more than 320mm)Viewing Distance 1m from the center of DisplayRange Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NMRange Marker 0.025, 0.05, 0.1, 0.25, 0.5, 1, 2, 4, 8, 16NMRange Accuracyr Less than 1% of the Range Scale in use, or 30m whichever is largerVariable Range Marker 2 (VRM1/VRM2)VRM Scale 0.000 to 100.0nm, Numerical Indication in 4 digitsBearing Scale 360° in 1° stepOff Center Within 66% of Radius, except 96nm rangeTrackball Cursor Built-in (Target Range, Relative/True bearing Presentation)Electronic Bearing Lines 2 (EBL1/EBL2) (on Center/Floating)EBLBearing Indication 000.0° to 359.9°Numerical Indication in 4 digitsTuning Indication Bar graphMarking Function Electronic Mark (Maximum 20 points)Heading Line Indication ElectronicTrue Motion Unit Built in (0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24 and 48nm)Anti Sea Clutter (SEA) Manual/AUTOAnti Rain Clutter (SEA) Manual/AUTODisplay mode North-up / Head-up / Course-upTrails Indication Off/0.25/0.5/1/3/6/10/15min and ContinuesVideo Process (PROC) Built in (Scan correlation / Remain)Interference Rejection (IR) Built in ( Off / Low / Middle / High)Auto-acquisition Zone (AZ) Sector (2)User MapiBuilt in, Mark and Line (20,000 points)Self diagnostic function Built inOwn Ship's Track IndicationiBuilt inParallel Index Line (PI) Built inAIS Indication Built in DisplayActivate 300100　Association function:Built inInterfacing Slave Display (TRG, VD, BP, BZ)GPS IEC61162-1(NMEA0183)LOG GYRO AIS IEC61162-2 Inter Switch (OPTION)Radar Buoy External Alarm outputReceivable Signal

11 －18JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.17 DISPLAY UNIT (NCD-4990)Receive capability Port: NAV1/ALM/ARPA/JARPA at terminal board TB4501 COM port (D-Sub 9 PIN)Navigation equipment IEC61162-1/2 Longitude/Latitude GGA>RMC>RMA>GNS>GLLWaypoint RMB>BWC(BWR) COG/SOG RMC＞RMA＞VTGSPEED VBWDay/Time information ZDAAlarm acknowledge ACKRate of Turn ROTRudder RSABearing signal GYRO-SYNC 360x, 180x, 90x, 36x(GYRO I/F)GYRO-STEP 360x, 180x, 90x, 36x(GYRO I/F)IEC61162-2 38400bps THS>HDT　over 40Hz(HDG port at terminal board TB4501)IEC61162-1ii HDT>HDG>HDM>VHW (HDG port at terminal board TB4501)Speed signal LOG-SYNC 360x, 180x, 90x, 30x(GYRO I/F)LOG-PULSE 800, 400, 200, 100(GYRO I/F)External event mark Contact input (EVENT port at terminal board TB4601)Radar buoy Negative input (RBVD port at terminal board TB4401)Depth IEC61162-1/JRC DPT>DBS>DBT>DBK, JRC formatWater temperature IEC61162-1/JRC MTW, JRC formatTendency IEC61162-1/JRC CUR, JRC formatWind IEC61162-1 MWV>MWDAIS IEC61162-2 VDM,VDO (AIS port at terminal board TB 4601 )Acknowledge Contact input (SYSACK, ARPAACK, PWRACK port at terminal board TB4601)Sendable SignalSlave video Radar video: TIY, VD, BP(2048p), BZ(Terminal board TB4401)Send capability Port NAV1, NAV2, ALM, ARPA, JARPA port at terminal board TB4303. COM port (D-Sub 9 PIN)Navigation information IEC61162-1/2 Radar system data RSDOwn ship data OSDTracking target data TTM,TLL,TTD,TLB,JRC-ARPAAIS target data TTM,TLL,TTD,TLBAlarm ALRAuto pilot APBBearing of destination BODLatitude/Longitude data GGA,GLL,RMCWaypoint RMB,BWCCOG/SOG VTGCross track error XTEHeading data HDT,THSExternal alarm Default setting normally closed contact

JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.17 DISPLAY UNIT (NCD-4990)11 －1911Maximum current 200mA (SYSALM, ALPAALM, PWRALM port at terminal board TB4601)Acknowledge Contact output (ACKOUT port at terminal board TB4401)Watchman reset Contact output (WMRST port at terminal board TB4401)Remote maintenance JRC format (MNT port at terminal board TB4601)AIS alarm acknowledge ACK (AIS port at terminal board TB4601)External monitor Multi scan monitor Analog RGB, HD15pin Connector 2 porti. Only with Navigation Equipment is connected.The Speed measuring accuracy of speed sensor shall confirm to IMO Resolution MSC.96(72).The measuring accuracy of GPS shall confirm to IMO Resolution MSC.112(73).ii. Can't be use for target tracking.

11 －20JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.18 Target Tracking Function11.18 Target Tracking FunctionTarget Tracking FunctionAvailable range scale All rangeAcquisition Acquisition mode Manual/AUTO（AUTO mode uses Auto-acquisition Zone）Manual Cancellation Any one Target or All targets at onceTracking Number of Target 100 Targets (AUTO Tracking)Maximum tracking range 32nm (Available all range scale)Presentation Display mode TM (True Motion) / RM (Relative Motion)Azimuth mode North-up / Head-up / Course-upVector mode True/Relative DisplayVector Length Variable, 1 to 60 min. (1min. step)Past Position True/Relative Display　Number of Dots…10 points　 Display Interval Time…0.5 / 1 / 2/ 4 minTime to Display Vector Within 1minTime to Stabilize Vector Within 3minAlarm Auto-acquisition Zone 2 (sector)Setting Range AZ1 (0.5～32NM),AZ2 (0.5～32NM)Alarm Indication Symbol on Display, Visible / Audible AlarmSafe Limits Setting Condition CPA LIMIT 0.1 to 9.9NM（CPA／TCPA）TCPA LIMIT 1 to 99 minuteSetting Condition Safe Target CPA＞CPA LIMIT0＞TCPATCPA＞TCPA LIMITDanger Target CPA≦CPA LIMIT0≦TCPA≦TCPA LIMITAlarm Indication Status Symbol Alarm AudibleSafe Target 〇(wht) OFF OFFDanger Target ○(red) CPA/TCPA ONLost Target Symbol on DisplayVisible / Audible AlarmData Indication Target Data Simultaneous and Continuous Display for 4 TargetsTrue Bearing, Range, True Course, True Speed,CPA,TCPA,BCR,BCTOwn Ship's Data Course and SpeedTrial Maneuver Manual SettingTrial Course 0°to 359.9°Trial Speed 0 to 100 kn Accuracy of Display Complied with IMO RequirementSystem Failure Alarm Visible / Audible AlarmSpeed Input Manual/AUTO (LOG)

JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.19 AIS FUNCTION11 －211111.19 AIS FUNCTIONAIS機能Available range scale All rangeActivation Activation mode Manual/AUTO（AUTO mode uses Auto-activation Zone）Manual Cancellation Any one TargetPresentation Number of Activated Target 100 TargetsNumber of Target 300 Targets (sleeping target and activated target)Past Position True/Relative DisplayNumber of Dots…10 pointsDisplay Interval Time…0.5 / 1 / 2/ 4 minDisplay Interval distance…0.1 / 0.2 / 0.5/ 1 NMMessage Broadcast Message, Addressed MessageDisplay mode TM (True Motion) / RM (Relative Motion)Azimuth mode North-up / Head-up / Course-upVector mode True/Relative DisplayVector Length Variable, 1 to 60 min. (1min. step)Alarm Auto-activation Zone 2 (Sector)Setting Range AZ1(0.5 to 32nm), AZ2(0.5 to 32nm)Alarm Indication Symbol on Display, Visible / Audible AlarmSafe Limits Setting Condition CPA LIMIT 0.1 to 9.9NM（CPA／TCPA）TCPA LIMIT 1 to 99minAlarm Condition Safe Target CPA＞CPA LIMIT0＞TCPATCPA＞TCPA LIMITDanger Target CPA≦CPA LIMIT0≦TCPA≦TCPA LIMITAlarm Indication Status Symbol Alarm AudibleSafe Target △(wht) OFF OFFDanger Target △(red) CPA/TCPA ONLost Target Symbol on DisplayVisible / Audible AlarmData Indication Target Data Simultaneous and Continuous Display for 2 Targetssimple display Ship's Name, Call Sign, MMSI, Course, Speed, CPA and TCPAdetail display Ship's Name, Call Sign, MMSI, Course, Speed, CPA, TCPA, Bearing, Range, Ship's Heading Bearing, Rate of Turn, Latitude, Longitude, Destination and Navigation StatusOwn Ship's Data The ship's name, call sign, MMSI, course, speed, ship's heading bearing, rate of turn, latitude, longitude, destination and navigation status of own shipTrial Maneuver Manual SettingTrial Course 0° to 360°Trial Speed 0 to 100 kn

11 －22JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.20 PERFORMANCE MONITOR (NJU-84) 11.20 PERFORMANCE MONITOR (NJU-84) 11.21 PERFORMANCE MONITOR (NJU-85) 11.22 AC-DC CONVERTER (NBA-5135)Accuracy of Display Complied with IMO RequirementSystem Failure Alarm Visible / Audible AlarmSpeed Input Auto (LOG)PERFORMANCE MONITORNJU-84Dimension Width 130 x Depth 180 x Height 70 (mm)Mass Approx.0.7kgOperating Frequency 3050±30MHzPERFORMANCE MONITORNJU-85Dimension Width 130 x Depth 149 x Height 70 (mm)Mass Approx.0.7kgOperating Frequency 9410±30MHzAC-DC CONVERTERNBA-5135Dimension Width 315 x Depth 385 x Height 99 (mm)Mass Approx.5kgPower supply Input AC100 to 240V, 50/60Hz, 1φOutput Voltage DC24V +/-5%Output Current 12A max

NQE-3141 Interswitch UnitA.1 OVERVIEW ............................................................................................A-1A.1.1 Overview .........................................................................................A-1A.1.2 Interswitch Setup ...........................................................................A-1A.2 INTERSWITCH OPERATION ................................................................A-3A.2.1 Operation Flow ...............................................................................A-3A.2.2 Inter Switch Menu ...........................................................................A-4A.2.3 Change of Connection Pattern (with 2 Display Units) ................A-6A.2.4 Change of Connection Pattern (with 3 or More Display Units) ..A-7A.2.5 Operating Connection Pattern Files (File Operations) ...............A-8A.2.6 Names of Display Units and Scanner Units .................................A-9A.3 REFERENCE .......................................................................................A-10A.3.1 Preheat Time after Change of Connection Pattern ...................A-10A.3.2 Notes on Changing Connection Pattern ....................................A-10A.3.3 Notes on Connecting Slave Display Unit ...................................A-10A.3.4 Setting at Installation ...................................................................A-11Appendix ANQE-3141 Interswitch Unit

JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.1 OVERVIEWA－1AA.1 OVERVIEWA.1.1 OverviewInterswitch NQE-3141 is equipment that enables free changeover between radar display units installed on the bridge and antenna units having different characteristics.If display unit is turned off or malfunctioned, the scanner unit can be controlled by other display unit.If interswitch unit had malfunctioned, the radar system is switched to standalone mode.Up to 8 units can be changed over.When the connected scanner is changed, following setting values are automatically loaded. A.1.2 Interswitch SetupConnection modes can be changed simply by changing the interswitch connection (upper left of the display).Tune Adjustment Section 7.1.3 "Tuning (Tune Adjustment)"Bearing Adjustment Section 7.1.4 "Bearing Adjustment"Range Adjustment Section 7.1.5 "Range Adjustment"Antenna Height Section 7.1.8 "Antenna Height Setting (AntennaHeight)"Antenna installation location Section 7.1.9 "Setting of CCRP (CCRP Setting)"Sector Blank Section 7.2.2 "Sector Blank Setting (Sector Blank)"TNI Blank Section 7.2.3 "TNI Blank Setting (TNI Blank)"Performance monitoradjustment Section 7.3.4 "Adjustment of Performance Monitor"PRF Fine Tuning Section 3.8.3 "Set Scanner Unit (TXRX Setting)"A master display unit is always necessary for establishing a slaveconnection.Before a slave display unit can be placed in transmission state, themaster display unit must be placed in transmission state.i

A－2JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.1 OVERVIEWupper left of the display The upper stand indicates the number of the connected scanner unit.The lower stand indicates the connection mode. :Mode in which the scanner unit can be controlled by thedisplay unit:Mode in which the scanner unit cannot be controlledii. When Slave is selected, transmission / standby and pulse length cannot be changed.The available range is also limited.Connection Switch ConnectedScanner UnitConnectionModeMasterSlave

JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATIONA－3AA.2 INTERSWITCH OPERATIONFollow the flowchart below to change the current interswitch connection pattern.A.2.1 Operation Flow Close the Inter Switch Menu .Change the connection pattern .Place the transmission standby state .Open the Inter Switch Menu .

A－4JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATIONA.2.2 Inter Switch MenuThe Inter Switch Menu can be opened only when the transmission standby state.Procedures1) Press the [TX/STBY] key to stop transmitting.The transmission standby state will be placed.2) Move the cursor onto the Interswitch connection change (upper left of the display), and left-click.The Inter Switch Menu will appear.Exit1) Left-click the button.The Inter Switch Menu will close. Inter Switch Menu (with 2 Display Units) 0.Exitb. Set c.ExitCurrent connection statusa. Connection patternDisplay unit in operation

JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATIONA－5Aa. Connection patternIf this button is clicked, the connection pattern is selected.The display unit in operation is enclosed in a square □.The background of the current connection pattern display is highlighted.b. SetIf this button is clicked, the change of connection is determined.c. ExitIf this button is clicked, the Inter Switch Menu is closed . Inter Switch Menu (with 3 or More Display Units)a. Connected scanner unitIn mode for naming a display unit or antenna unit, clicking on a unit opens the name input window.If only 2 display units are installed but the interswitch is set for 3or more display units, the Inter Switch Menu for 3 or moredisplay units will appear.ib. Display unit connected as masterd. Namee. File Operationsc. Display unit connected as slavef. Setg. Exita. Connectedscanner unit

A－6JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATIONb. Display unit connected as masterc. Display unit connected as slaveIf this button is clicked, select / cancel the display unit.If this button is clicked in the naming a display unit or scanner unit mode , the name input window is opened .d. NameIf this button is clicked, set to the display or scanner unit rename mode.e. File OperationsIf this button is clicked, the File Operations menu is opened.。f. SetIf this button is clicked, the change of connection is determined.g. ExitIf this button is clicked, the Inter Switch Menu is closed . A.2.3 Change of Connection Pattern (with 2 Display Units)If two display units are installed, a connection pattern needs to be selected.Procedures1) Open the Inter Switch menu (with 2 Display Units).2) Move the cursor onto the Connection pattern (see Section A.2.2 "Inter Switch Menu" and Section a. "Connection pattern") to be changed , and left-click.The connection pattern will be selected, and (Section b. "Set") will blink.3) Left-click the button.The connection pattern will be changed. 3. Set3. Set

JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATIONA－7AA.2.4 Change of Connection Pattern (with 3 or More DisplayUnits)If three or more display units are installed, the layout of connection patterns needs to be set.Procedures1) Open the Inter Switch Menu (with 3 or More Display Units).2) Move the cursor onto the display unit (Section b. "Display unit connected as master" or Section c. "Display unit connected as slave") to be changed , and left-click.The selected display unit will be highlighted.To deselect the display unit, left-click key again.3) Move the cursor to the change-destination display unit, and left-click.he selected display unit in step 2 will be switched to the change-destination display unit, and (Section f. "Set") will blink.If the change destination is empty, control will move and will blink.4) Left-click the button.The connection pattern will be changed. A master display unit is always necessary for establishing aslave connection.3. Set3. Set3. Seti

A－8JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATIONA.2.5 Operating Connection Pattern Files (File Operations)Frequently used connection patterns can be read easily by saving interswitch connection patterns.[1] Loading connection patterns (Load)Procedures1) Open the Inter Switch Menu (with 3 or More Display Units).2) Left-click the button.The File Operations menu will appear.3) Left-click the button.Currently saved connection patterns in memory will be listed.4) Left-click the button corresponding to the file to be loaded.Confirmation Window will appear.5) Left-click the to load.The connection pattern will be changed. [2] Saving connection patterns (Save)Procedures1) Open the Inter Switch Menu (with 3 or More Display Units).2) Left-click the button.The File Operations window will appear.3) Left-click the button.The Save menu will appear.Currently saved connection patterns in memory will be listed.4) Left-click the button corresponding to the file to be saved.The Input File Name window will appear.5) Enter the file name to be saved.Up to 8 characters can be entered.For the input method on the character input screen, see Section 3.3.4.7 "Entering a character".The connection pattern will be saved when the name is input.2. File Operation3. Load1. Yes2. File Operation2. Save

JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATIONA－9A[3] Erasing a connection pattern (Erase)Procedures1) Open the Inter Switch Menu (with 3 or More Display Units).2) Left-click the button.The File Operations window will appear.3) Left-click the button. The Erase menu will appear.The list of connection patterns stored in the memory will be displayed.4) Left-click the button corresponding to the file to be erased.Confirmation Window will appear.5) Left-click the to load.The selected connection pattern is erased and the file name is deleted from the list. A.2.6 Names of Display Units and Scanner UnitsThe display units and antenna units can be named.Procedures1) Open the Inter Switch Menu (with 3 or More Display Units).2) Left-click the button. "Name" will be highlighted, indicating that the rename mode is activated.3) Move the cursor to the display unit (Section b. "Display unit connected as master" or Section c. "Display unit connected as slave") or scanner unit (Section a. "Connected scanner unit") to be renamed , and left-click.he Input IND Name or the Input TXRX Name window will appear.4) Input a new unit name.Up to 8 characters can be input as a unit name. For the input method on the character input menu, see Section 3.3.4.7 "Entering a character".The selected display unit or antenna unit will be renamed when the new name is input. 2. File Operation3. Erase1. Yes1. Name

A－10JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.3 REFERENCEA.3 REFERENCEA.3.1 Preheat Time after Change of Connection PatternAfter the current interswitch connection pattern has been changed, operation needs to wait until the system is ready. This is because the preheat time varies depending on the previous connection of the scanner unit and display unit. The wait time is necessary for protecting the electronic tubes that emit radio waves.A.3.2 Notes on Changing Connection PatternAn attempt to change to another connection pattern immediately after the completion of connection pattern change may fail.This is because internal processing still needs some preparation time upon completion of connection pattern change. Let several seconds pass between connection pattern change operations.A.3.3 Notes on Connecting Slave Display UnitBefore a slave display unit can be placed in transmission state, the master display unit must be placed in transmission state. If the master display unit is moved from the transmission state to the transmission standby state, the slave display unit is forcibly placed in transmission standby state. When they are in transmission standby state, is shown in the alarm indication (lower right of the display), and the alarm sounds.A slave display unit cannot control tune. Tune is controlled by the master display unit. is shown in the transmitter pulse length (upper left of the display).Range change for a slave display unit is limited by the range and pulse length / repetition frequency of the master display unit. As a rule, a greater range than the range of the master display unit cannot be set for a slave display unit. However, if the transmitter pulse length of a slave display unit is identical to the master display unit's and the repetition frequency is within the master display unit's, a greater range than the master display unit's can be selected for the slave display unit. When the master display unit narrows the range or changes the transmitter a) When not changed to a new connection pattern Preheating not requiredb) When changed to a new connection pattern and an scanner unit had been used before the change Preheating not requiredc) When changed to a new connection pattern and an scanner unit had not been used before the change Preheating requiredTXRX StandbySlave

JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.3 REFERENCEA－11Apulse length, the range of the slave display unit may be forcibly changed. In this case, is shown in the alarm indication (lower right of the display), and the alarm sounds.A.3.4 Setting at InstallationSetting of the interswitch circuit (CCL-304*)The settings of the DIP switches SW11 to SW13 are shown below.1) SW11 setting (extension mode and master/slave settings)Master Range CHGSW 11 SW 13 SW 12Interswitch circuit PCBCCL-304*4DescriptionExtension mode settingON Extension modeOFF Normal mode3DescriptionON SlaveOFF Master1, 2 DescriptionON UnusedOFF UnusedUnusedMaster/slave settingSet the switch to OFF if the number of connected display units is four or less.Set the switch to ON if the slave ISW PCB is selected in extension mode.Set the switch to OFF in normal state.1234ONOFF

A－12JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.3 REFERENCE2) SW12 setting (radar connection settings)3) SW13 (unused) Before the DIP switches of the interswitch circuit can be set, theinterswitch breaker must be turned off in order to ensure safetyoperation.1234ONOFF8Radar connection settingsON No.8 display unit connectedOFF No.8 display unit not connected56787ON No.7 display unit connectedOFF No.7 display unit not connected6ON No.6 display unit connectedOFF No.6 display unit not connected5ON No.5 display unit connectedOFF No.5 display unit not connected4ON No.4 display unit connectedOFF No.4 display unit not connected3ON No.3 display unit connectedOFF No.3 display unit not connected2ON No.2 display unit connectedOFF No.2 display unit not connected1ON No.1 display unit connectedOFF No.1 display unit not connected1,2,3,4 Unused (All OFF)1234ONOFF

DRAWINGSB.1 Interconnection Diagram of Display Unit ...........................................B-1B.1.1 NCD-4990 ........................................................................................B-2B.1.2 NCD-4990 w/NBA-5135 ...................................................................B-3B.1.3 NCD-4990T ......................................................................................B-4B.1.4 NCD-4990T w/NBA-5135 ................................................................B-5B.1.5 NWZ-170-R ......................................................................................B-6B.1.6 NWZ-170-RT ....................................................................................B-7B.1.7 NCE-5163-R .....................................................................................B-8B.1.8 NCE-5163-RT ...................................................................................B-9B.1.9 NBA-5135 ......................................................................................B-10B.2 Power System Daigram of Display Unit ...........................................B-11B.3 Signal Flow Diagram of Display Unit ................................................B-12B.4 Primary Power System Diagram .......................................................B-13B.5 Block Diagram of Scanner Unit ........................................................B-14B.5.1 NKE-2103 ......................................................................................B-15B.5.2 NKE-2254 ......................................................................................B-16B.5.3 NKE-1125/NKE-1130 .....................................................................B-17Appendix BDRAWINGS

B.5.4 NKE-1129, NTG-3225 / NKE-1139, NTG-3230 .............................B-18B.6 Interconnection Diagram of Scanner Unit .......................................B-19B.6.1 NKE-2103 ......................................................................................B-20B.6.2 NKE-2254 ......................................................................................B-21B.6.3 NKE-1125 (AC110V) ......................................................................B-22B.6.4 NKE-1125 (AC220V) ......................................................................B-23B.6.5 NKE-1129 (AC110V) ......................................................................B-24B.6.6 NKE-1129 (AC220V) ......................................................................B-25B.6.7 NTG-3225 ......................................................................................B-26B.6.8 NKE-1130 (AC110V) ......................................................................B-27B.6.9 NKE-1130 (AC220V) ......................................................................B-28B.6.10 NKE-1139 (AC110V) ......................................................................B-29B.6.11 NKE-1139 (AC220V) ......................................................................B-30B.6.12 NTG-3230 ......................................................................................B-31B.7 Terminal Board Connection Diagram ...............................................B-32B.7.1 JMA-9110-6XA/JMA-9110-6XAH ..................................................B-33B.7.2 JMA-9110-6XA/JMA-9110-6XAH (desktop) .................................B-34B.7.3 JMA-9122-6XAH ............................................................................B-35B.7.4 JMA-9122-6XAH (desktop) ...........................................................B-36B.7.5 JMA-9122-6XA/9XA ......................................................................B-37B.7.6 JMA-9123-7XA/9XA ......................................................................B-38B.7.7 JMA-9132-SA ................................................................................B-39B.7.8 JMA-9133-SA ................................................................................B-40B.7.9 NCD-4990T ....................................................................................B-41B.8 GYRO I/F .............................................................................................B-42B.9 Inter Switch Unit .................................................................................B-44B.9.1 Terminal Board Connection Diagram .........................................B-44B.9.2 Interconnection Diagram .............................................................B-46

JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display UnitB－1BB.1 Interconnection Diagram of Display Unit

B－2JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display UnitB.1.1 NCD-4990Fig B-1: Interconnection Diagram of NCD-49902PJ430826PJ430726PJ430650PJ430118PJ43048PJ43053PJ43133PJ43149PJ430914PTB4101TO TRUTO ISW26PTB4201TO EXT-RADAR30PTB4401TO SEN SOR22PTB4501TO A LARM SYSTEM22PTB4601TO GYRO6PTB4701TO LOG12PTB4801TO PC9PJ4310TERMINAL BOARDCQD-2097PC43050PJ430250PJ430330PJ4311TO OPU30PJ4312TO SUB OPU6PJ64116PJ6410 6PJ64096PJ6408 2PJ6406 7PJ6405 14PJ6404 14PJ6403 15 PJ640230PJ6401OPERATION CIRCUIT D CCK-976 PC64014PJ6101 15 PJ6102OPERATION CIRCUIT A CCK-973 PC6107PJ6201OPERATION CIRCUIT B CCK-974 PC620SP1A1*PS/2 EXTENSION CABLE(USER SUPPLY )OPERATION UNITNCE-5163-R2 m H - 7ZC RD 133 7 (N CE- 5 16 3 -R )JR C SU PPLYB101B102PC90011PTB91415PTB91311PTB91215PTB9112PTB905INTERSWITCH UNITNQE-3141-2ACH1CH250PJ410550PJ410650PJ4107*OPTIONW401 H-7ZCRD1339W402 H-7ZCRD1339W403 H-7ZCRD133964PJ410364PJ410464PJ410264PJ410164PJ4401 64PJ4402 64PJ1GYRO INTERFACECIRCUITCMJ-462EPC420RADAR PROCESSCIRCUITCDC-1324PC440MOTHERBOARDCQC-1192PC41064PJ440364PJ4404AIS PROCESSCIRCUITCDC-1325PC46064PJ460164PJ4501ARPA PROCESSCIRCUITCDC-1186DPC45015PJ4409VGA15PJ4405VGA28PJ4406DVI-D8PJ4407RJ-4550PJ4408CF-cardLCDOPERATIONCIRCUITCCK -972 PC7108PJ711MONITOR UNITNWZ-170-RLCD PANELH-7WSRD0002A8PH-7ZCRD13289P 2m H-7ZCRD1329A (NWZ-170-R)DVI 2m H-7ZCRD1345 (NWZ-170-R)20PJ41088PPOWER SUPPLYCBD-166118P20P*PS/2 MOUSE/TRKBALL(USER SUPPLY)*OPTION(USER SUPPLY)2P2PAC OUT2+ーUVWBATTERYINAC OUT2AC INUWVUWV4351A07335 FILTERINOUTREDWHTBLUREDWHTBLUAC 2m 5ZCGH00285 (NWZ-170-R)AC100-115V 50/60HzAC220-240V 50/60HzSCANNER MOTORPOWER NCD-4990（自立型）　機内接続図Interconnection diagram of DISPLAY UNIT type NCD-4990(self standing)JMA-9122-6/9XA,JMA-9123-7/9XA,JMA-9132-SA,JMA-9133-SARADAR PROCESS UNITNDC-1399-9

JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display UnitB－3BB.1.2 NCD-4990 w/NBA-5135Fig B-2: Interconnection Diagram of NCD-4990 w/NBA-51352PJ430826PJ430726PJ430650PJ430118PJ43048PJ43053PJ43133PJ43149PJ430914PTB4101TO TRUTO ISW26PTB4201TO EXT-RADAR30PTB4401TO S ENSOR22PTB4501TO A LARM SYSTEM22PTB4601TO GYRO6PTB4701TO LOG12PTB4801TO PC9PJ4310TERMINAL BOARDCQD-2097PC43050PJ430250PJ430330PJ4311TO OPU30PJ4312TO SUB OPU6PJ64116PJ6410 6PJ64096PJ6408 2PJ6406 7PJ6405 14PJ6404 14PJ6403 15PJ640230PJ6401OPERATION CIRCUIT D CCK-976 PC64014PJ6101 15PJ6102OPERATION CIRCUIT A CCK-973 PC6107PJ6201OPERATION CIRCUIT B CCK-974 PC620SP1A1*PS/2 EX TENSION CA BLE(USER SUPPLY )OPERATION UNITNCE-5163-R2m H -7ZC RD 1 33 7 (N CE - 5 163 - R )JRC SU PPLYB101B102PC90011PTB91415PTB91311PTB91215PTB9112PTB905INTERSWITCH UNITNQE-3141-2ACH1CH250PJ410550PJ410650PJ4107*OPTIONW401 H -7ZCRD1339W402 H -7ZCRD1339W403 H -7ZCRD133964PJ410364PJ410464PJ410264PJ410164PJ4401 64PJ4402 64PJ1GYRO INTERFACECIRCUITCMJ-462EPC420RADAR PROCESSCIRCUITCDC-1324PC440MOTHERBOARDCQC-1192PC41064PJ440364PJ4404AIS PROCESSCIRCUITCDC-1325PC46064PJ460164PJ4501ARPA PROCESSCIRCUITCDC-1186DPC45015PJ4409VGA15PJ4405VGA28PJ4406DVI-D8PJ4407RJ-4550PJ4408CF-cardLCDOPERATIONCIRCUITCCK -972 PC71 08PJ711MONITOR UNITNWZ-170-RLCD PANELH-7WSRD0002A8PH-7ZCRD13289P 2m H-7ZCRD1329A (NWZ-170-R )DVI 2m H-7ZCRD1345 (NWZ-170-R)20PJ41088PPOWER SUPPLYCBD-166118P20P*PS/2 MOUSE/TRKBALL(USER SUPPLY)*OPTION(USER SUPPLY)2P2PAC OUT2+ーUVWBATTERYINAC OUT2AC INUWVUWV4351A07335 FILTERINOUTREDWHTBLUREDWHTBLUAC 2m 5ZCGH00285 (NWZ-170-R)U V FG+ーFGTB522AC INTB521DC24V OUTAC/DC CONVERTER UNITNBA-5135AC100-115V 50/60HzAC220-240V 50/60HzSCAN NER MOTORPOWER DC24VNCD-4990（自立型）　機内接続図Interconnection diagram of DISPLAY UNIT type NCD-4990(self standing)JMA-9110-6XA,JMA-9110-6XAH,JMA-9122-6XAHRADAR PROCESS UNITNDC-1399-9W406 H-7ZCRD1342AREDWHTREDWHT

B－4JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display UnitB.1.3 NCD-4990TFig B-3: Interconnection Diagram of NCD-4990T2PJ430826PJ430726PJ430650PJ430118PJ43048PJ43053PJ43133PJ43149PJ430914PTB4101TO TRUTO ISW26PTB4201TO EXT-RADAR30PTB4401TO S ENSOR22PTB4501TO A LARM SYSTEM22PTB4601TO GYRO6PTB4701TO LOG12PTB4801TO PC9PJ4310TERMINAL BOARDCQD-2097PC43050PJ430250PJ430330PJ4311TO OPU30PJ4312TO SUB OPU6PJ64116PJ6410 6PJ64096PJ6408 2PJ6406 7PJ6405 14PJ6404 14PJ6403 15PJ640230PJ6401OPERATION CIRCUIT D CCK-976 PC64014PJ6101 15PJ6102OPERATION CIRCUIT A CCK-973 PC6107PJ6201OPERATION CIRCUIT B CCK-974 PC620SP1A1*PS/2 EX TENSION CA BLE(USER SUPPLY )OPERATION UNITNCE-5163-RT5m H -7ZC RD 1 33 8 (N CE - 5 163 - R T)JRC SU PPLYB101B102PC90011PTB91415PTB91311PTB91215PTB9112PTB905INTERSWITCH UNITNQE-3141-2ACH1CH250PJ410550PJ410650PJ4107*OPTIONW401 H -7ZCRD1339W402 H -7ZCRD1339W403 H -7ZCRD133964PJ410364PJ410464PJ410264PJ410164PJ4401 64PJ4402 64PJ1GYRO INTERFACECIRCUITCMJ-462EPC420RADAR PROCESSCIRCUITCDC-1324PC440MOTHERBOARDCQC-1192PC41064PJ440364PJ4404AIS PROCESSCIRCUITCDC-1325PC46064PJ460164PJ4501ARPA PROCESSCIRCUITCDC-1186DPC45015PJ4409VGA15PJ4405VGA28PJ4406DVI-D8PJ4407RJ-4550PJ4408CF-cardLCDOPERATIONCIRCUITCCK -972 PC71 08PJ711MONITOR UNITNWZ-170-RTLCD PANELH-7WSRD0002A8PH-7ZCRD13289P 5m H-7ZCRD1330A (NWZ-170-R T)DVI 5m H-7ZCRD1346 (NWZ-170-RT)20PJ41088PPOWER SUPPLYCBD-166118P20P*PS/2 MOUSE/TRKBALL(USER SUPPLY)*OPTION(USER SUPPLY)2P2PAC OUT2+ーUVWBATTERYINAC OUT2AC INUWVUWV4351A07335 FILTERINOUTREDWHTBLUREDWHTBLUAC 5m 5ZCGH00364 (NWZ-170-RT)AC100-115V 50/60HzAC220-240V 50/60HzSCANNER MOTORPOWERNCD-4990T（卓上型）　機内接続図Interconnection diagram of DISPLAY UNIT type NCD-4990T(desktop)RADAR PROCESS UNITNDC-1399-9T1 2 31 2 3REDBLUWHTW405 H-7ZCRD1341ATB402JMA-9122-6/9XA,JMA-9123-7/9XA,JMA-9132-SA,JMA-9133-SA

JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display UnitB－5BB.1.4 NCD-4990T w/NBA-5135Fig B-4: Interconnection Diagram of NCD-4990T w/NBA-51352PJ430826PJ430726PJ430650PJ430118PJ43048PJ43053PJ43133PJ43149PJ430914PTB4101TO TRUTO ISW26PTB4201TO EXT-RADAR30PTB4401TO S ENSOR22PTB4501TO A LARM SYSTEM22PTB4601TO GYRO6PTB4701TO LOG12PTB4801TO PC9PJ4310TERMINAL BOARDCQD-2097PC43050PJ430250PJ430330PJ4311TO OPU30PJ4312TO SUB OPU6PJ64116PJ6410 6PJ64096PJ6408 2PJ6406 7PJ6405 14PJ6404 14PJ6403 15PJ640230PJ6401OPERATION CIRCUIT D CCK-976 PC64014PJ6101 15PJ6102OPERATION CIRCUIT A CCK-973 PC6107PJ6201OPERATION CIRCUIT B CCK-974 PC620SP1A1*PS/2 EX TENSION CA BLE(USER SUPPLY )OPERATION UNITNCE-5163-RT5m H -7ZC RD 1 33 8 (N CE - 5 163 - R T)JRC SU PPLYB101B102PC90011PTB91415PTB91311PTB91215PTB9112PTB905INTERSWITCH UNITNQE-3141-2ACH1CH250PJ410550PJ410650PJ4107*OPTIONW401 H -7ZCRD1339W402 H -7ZCRD1339W403 H -7ZCRD133964PJ410364PJ410464PJ410264PJ410164PJ4401 64PJ4402 64PJ1GYRO INTERFACECIRCUITCMJ-462EPC420RADAR PROCESSCIRCUITCDC-1324PC440MOTHERBOARDCQC-1192PC41064PJ440364PJ4404AIS PROCESSCIRCUITCDC-1325PC46064PJ460164PJ4501ARPA PROCESSCIRCUITCDC-1186DPC45015PJ4409VGA15PJ4405VGA28PJ4406DVI-D8PJ4407RJ-4550PJ4408CF-cardLCDOPERATIONCIRCUITCCK -972 PC71 08PJ711MONITOR UNITNWZ-170-RTLCD PANELH-7WSRD0002A8PH-7ZCRD13289P 5m H-7ZCRD1330A (NWZ-170-R T)DVI 5m H-7ZCRD1346 (NWZ-170-RT)20PJ41088PPOWER SUPPLYCBD-166118P20P*PS/2 MOUSE/TRKBALL(USER SUPPLY)*OPTION(USER SUPPLY)2P2PAC OUT2+ーUVWBATTERYINAC OUT2AC INUWVUWV4351A07335 FILTERINOUTREDWHTBLUREDWHTBLUAC 5m 5ZCGH00364 (NWZ-170-RT)U V FG+ーFGTB522AC INTB521DC24V OUTAC/DC CONVERTER UNITNBA-5135AC100-115V 50/60HzAC220-240V 50/60HzSCAN NER MOTORPOWER DC24VNCD-4990T（卓上型）　機内接続図Interconnection diagram of DISPLAY UNIT type NCD-4990T(desktop)JMA-9110-6XA,JMA-9110-6XAH,JMA-9122-6XAHRADAR PROCESS UNITNDC-1399-9T1 2 31 2 3REDBLUWHTW405 H-7ZCRD1341ATB4021 2 31 2 3TB401W408 H-7ZCRD1344A GR NGR NW407 H-7ZCRD1343AWHTBLKGRNWHTBLKGRN

B－6JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display UnitB.1.5 NWZ-170-RFig B-5: Interconnection Diagram of NWZ-170-RJ7101BRILLAC 1 0 0V240VFANALMDVIRGBCCK-972PC710H-7WSRD0002ALCD8PH-7ZCRD1328FL19P 2m H-7ZCRD1329ADVI 2m H-7ZCRD1345AC 2m VM0301-VM0303B2MｸﾛCDC-1324J4406CQD-2097J4309CBD-1661OUTLETMonitor Unit InterconnectionCML-764-R (NWZ-170-R)

JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display UnitB－7BB.1.6 NWZ-170-RTFig B-6: Interconnection Diagram of NWZ-170-RT J7101BRILLAC 1 0 0V240VFANALMDVIRGBCCK-972PC710H-7WSRD0002ALCD8PH-7ZCRD1328FL19P 5m H-7ZCRD1330ADVI 5m H-7ZCRD1346AC 5m VM0301-VM0303B5MｸﾛCDC-1324J4406CQD-2097J4309CBD-1661OUTLETMonitor Unit InterconnectionCML-764-RT (NWZ-170-RT)

B－8JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display UnitB.1.7 NCE-5163-RFig B-7: Interconnection Diagram of NCE-5163-R6PJ64116PJ6410 6PJ64096PJ6408 2PJ6406 7PJ6405 14PJ6404 14PJ6403 15PJ640230PJ6401OPERATION CIRCUIT D CCK-976 PC 64014PJ6101 15PJ6102OPERATION CIRCUIT A CCK-973 PC6107PJ6201OPERATION CIRCUIT B CCK-974 PC620SP1A1OPERATION UNITNCE-5163-RW67 2m H-7ZCRD1337W62 H-7ZCRD1332W65 H-7ZCRD1335W63 H-7ZCRD1333AW64 H-7ZCRD1334FL12PJ6407Operation Unit InterconnectionCMD-996-R (NCE-5163-R)

JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display UnitB－9BB.1.8 NCE-5163-RTFig B-8: Interconnection Diagram of NCE-5163-RT6PJ64116PJ6410 6PJ64096PJ6408 2PJ6406 7PJ6405 14PJ6404 14PJ6403 15PJ640230PJ6401OPERATION CIRCUIT D CCK-976 PC 64014PJ6101 15PJ6102OPERATION CIRCUIT A CCK-973 PC6107PJ6201OPERATION CIRCUIT B CCK-974 PC620SP1A1OPERATION UNITNCE-5163-RTW68 5m H-7ZCRD1338W62 H-7ZCRD1332W65 H-7ZCRD1335W63 H-7ZCRD1333AW64 H-7ZCRD1334FL12PJ6407Operation Unit InterconnectionCMD-996-RT (NCE-5163-RT)

B－10JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display UnitB.1.9 NBA-5135Fig B-9: Interconnection Diagram of NBA-5135AC/DC Converter InterconnectionCBD-1684A (NBA-5135)FL1LF-210FS11 2 31 2 3TB521123123TB522A1AES300-24BUVW1 H-7ZCRD1495W2 H-7ZCRD1496BLKWHTREDTwisteduvFGRED WHTN LFG+ + + - - -RED WHTBLKBLKBLKBLKWHTWHTBLKWHTREDW6 H-7ZCRD1499W5 H-7ZCRD1499W4 H-7ZCRD1498W3 H-7ZCRD1497Twisted

JMA-9100 Instruction Manual > B.DRAWINGS > B.2 Power System Daigram of Display UnitB－11BB.2 Power System Daigram of Display UnitFig B-10: Power System Diagram of NCD-4990/T2PJ430826PJ430726PJ430650PJ430118PJ43048PJ43053PJ43133PJ43149PJ430914PTB4101TO TRUTO ISW26PTB4201TO EXT-RADAR30PTB4401TO SENSOR22PTB4501TO A LAR M SYSTEM22PTB4601TO GYRO6PTB4701TO LOG12PTB4701TO PC9PJ4310TERMINAL BOARDCQD-2097PC43050PJ430250PJ430330PJ4311TO OPU30PJ4312TO SUB OPU6PJ64116PJ6410 6PJ64096PJ6408 2PJ6406 7PJ6405 14PJ6404 14PJ6403 15PJ640230PJ6401OPERATION CIRCUIT D CCK-976 PC64014PJ6101 15PJ6102OPERATION CIRCUIT A CCK-973 PC6107PJ6201OPERATION CIRCUIT B CCK-974 PC620SP1A1*PS/2 EX TENSION CABLE(USER SU PPLY )OPERATION UNITNCE-5163-R2m H-7ZCRD1337 (NCE-5163-R)5m H-7ZCRD1338 (NCE-5163-RT)JRC SUPPLYB101B102PC90011PTB91415PTB91311PTB91215PTB9112PTB905INTERSWITCH UNITNQE-3141-2CH1CH250PJ410550PJ410650PJ4107*OPTIONW401 H -7ZCRD1339W402 H -7ZCRD1339W403 H -7ZCRD133964PJ410364PJ410464PJ410264PJ410164PJ4401 64PJ4402 64PJ1GYRO INTERFACECIRCUITCMJ-462EPC420RADAR PROCESSCIRCUITCDC-1324PC440MOTHERBOARDCQC-1192PC41064PJ440364PJ4404AIS PROCESSCIRCUITCDC-1325PC46064PJ460164PJ4501ARPA PROCESSCIRCUITCDC-1186DPC45015PJ4409VGA15PJ4405VGA28PJ4406DVI-D8PJ4407RJ-4550PJ4408CF-cardLCDOPERATIONCIRCUITCCK -972 PC7108PJ711MONITOR UNITNWZ-170-RLCD PANELH-7WSRD0002A8PH-7ZCRD13289P 2m H-7ZCRD 1329A (NWZ-170-R )DVI 2m H-7ZCRD1345 (NWZ-170-R)20PJ41088PPOWER SUPPLYCBD-166118P20P*PS/2 MOUSE/TRKBALL(USER SUPPLY)*OPTION(USER SUPPLY)2P2PAC OUT2+ーUVWBATTERYINAC OUT2AC INUWVUWV4351A07335 FILTERINOUTREDWHTBLUREDWHTBLUAC 2m 5ZCGH00285 (NWZ-170-R)U V FG+ーFGTB522AC INTB521DC24V OUTAC/DC CONVERTER UNITNBA-5135AC100-115V 50/60HzAC220-240V 50/60HzSCANNER MOTORPOWER DC24VNCD-4990 電源系統図Power supply system diagram of DISPLAY UNIT type NCD-4990(self standing)RADAR PROCESS UNITNDC-1399-9W406 H-7ZCRD1342AREDWHTREDWHTINPUT VOLTAGESELECT SWITCH3.3V,5V,12V,-12VP+5V P+12V3.3V,5V,12V,-12V+48V,DC+24V+24VP+5VP+12VDC+24V+5VU,VAC100-115VAC220-240V50/60Hz,1φU,VAC100-115VAC220-240V50/60Hz,1φU,VAC100-115VAC220-240V50/60Hz,1φ3.3V5VDC+24V+48V(to SCANNER UNIT)3.3V,5V,12V,-12V3.3V,5V,12V,-12V+48V,DC+24VJMA -9 110 -6X AJMA -9 110 -6X A HJMA -9 122 -6X A Honly

B－12JMA-9100 Instruction Manual > B.DRAWINGS > B.3 Signal Flow Diagram of Display UnitB.3 Signal Flow Diagram of Display UnitFig B-11: Signal Flow Diagram of NCD-4990/T2PJ430826PJ430726PJ430650PJ430118PJ43048PJ43053PJ43133PJ43149PJ430914PTB4101TO TRUTO ISW26PTB4201TO EXT-RADAR30PTB4401TO S ENSOR22PTB4501TO A LAR M SYSTEM22PTB4601TO GYRO6PTB4701TO LOG12PTB4701TO PC9PJ4310TERMINAL BOARDCQD-2097PC43050PJ430250PJ430330PJ4311TO OPU30PJ4312TO SUB OPU6PJ64116PJ6410 6PJ64096PJ6408 2PJ6406 7PJ6405 14PJ6404 14PJ6403 15PJ640230PJ6401OPERATION CIRCUIT D CCK-976 PC64014PJ6101 15PJ6102OPERATION CIRCUIT A CCK-973 PC6107PJ6201OPERATION CIRCUIT B CCK-974 PC620SP1A1*PS/2 EXTENSION CA BLE(USER SU PPLY )OPERATION UNITNCE-5163-R2m H-7ZCRD1337 (NCE-5163-R)5m H-7ZCRD1338 (NCE-5163-RT)JRC SU PPLYB101B102PC90011PTB91415PTB91311PTB91215PTB9112PTB905INTERSWITCH UNITNQE-3141-2CH1CH250PJ410550PJ410650PJ4107*OPTIONW401 H-7ZCRD1339W402 H-7ZCRD1339W403 H-7ZCRD133964PJ410364PJ410464PJ410264PJ410164PJ4401 64PJ4402 64PJ1GYRO INTERFACECIRCUITCMJ-462EPC420RADAR PROCESSCIRCUITCDC-1324PC440MOTHERBOARDCQC-1192PC41064PJ440364PJ4404AIS PROCESSCIRCUITCDC-1325PC46064PJ460164PJ4501ARPA PROCESSCIRCUITCDC-1186DPC45015PJ4409VGA15PJ4405VGA28PJ4406DVI-D8PJ4407RJ-4550PJ4408CF-cardLCDOPERATIONCIRCUITCCK -972 PC7108PJ711MONITOR UNITNWZ-170-RLCD PANELH-7WSRD0002A8PH-7ZCRD13289P 2m H-7ZCRD 1329A (NWZ-170-R )DVI 2m H-7ZCRD1345 (NWZ-170-R)20PJ41088PPOWER SUPPLYCBD-166118P20P*PS/2 MOUSE/TRKBALL(USER SUPPLY)*OPTION(USER SUPPLY)2P2PAC OUT2+ーUVWBATTERYINAC OUT2AC INUWVUWV4351A07335 FILTERINOUTREDWHTBLUREDWHTBLUAC 2m 5ZCGH00285 (NWZ-170-R)U V FG+ーFGTB522AC INTB521DC24V OUTAC/DC CONVERTER UNITNBA-5135AC100-115V 50/60HzAC220-240V 50/60HzSCANNER MOTORPOWER DC24VNCD-4990 信号系統図Signal flow diagram of DISPLAY UNIT type NCD-4990RADAR PROCESS UNITNDC-1399-9W406 H-7ZCRD1342AREDWHTREDWHTSerialRadar videoTrigger,RotaSerialRadar video,Trigger,RotatioRadar video,Trigger,RotatioSerialDry ContactGYRO(STEP/SYNLOG(PULSE/SYNSerialRadar video,Trigger,RotationRadar video,Trigger,RotationGYRO/LOGSerial,GPIORadar video,Trigger,RotationGYRO/LOGRadar video,Trigger,Rotation Serial,GPIOAnalog RGBAnalog RGBDegital Video InterfaceEthernet LCD Fan AlarmPower supply ControlPower supply Fan alarmPS/2 I/FPS/2 I/F Audio KEY matrixEncoderPower SWPower supply ControlPower supply Fan alarmDimmer

JMA-9100 Instruction Manual > B.DRAWINGS > B.4 Primary Power System DiagramB－13BB.4 Primary Power System DiagramFig B-12: Primary Power System DiagramPOWER CONTROLCIRCUITFAN ALM POWER CONTROLINTERSWITCH=1AOPERATION UNIT=0.5A(typ)GYRO I/F CIRCUIT=0.1A(typ)SCANNER X BAND_2.5A, S BAND_3.0ARADAR PROCESS CIRCUIT = 1.2A(typ)ARPA PROCESS CIRCUIT = 0.15A(typ)AIS PROCESS CIRCUIT = 0.15(typ)TERMINAL BOARD = 1.0A(typ)AC100-115VAC220-240V50/60Hz,1φSCANNERMOTOR POWERAC100/230V1φOVER VOLT AG EPROT ECTIONAC100-115VAC220-240V50/60Hz,1φRADAR PROCESS CIRCUIT = 2.2A(typ)ARPA PROCESS CIRCUIT = 0.1A(typ)AIS PROCESS CIRCUIT = 0.1(typ)TERMINAL BOARD = 0.2A(typ)RADAR PROCESS CIRCUIT = 0.1A(typ)TERMINAL BOARD = 0.4A(typ)RADAR PROCESS CIRCUIT = 0.1A(typ)TERMINAL BOARD = 0.1A(typ)BATTRYDC24VOPERATION UNIT = 0.1AP+12V+48V±3V+5. 0V+3. 3V-12V+12VCIRCUITBREAKER LINE FI LT ERVOLTAGE SELCTSWITCHMONITOR UNIT POWERSCANNER MOTOR POWER

B－14JMA-9100 Instruction Manual > B.DRAWINGS > B.5 Block Diagram of Scanner UnitB.5 Block Diagram of Scanner Unit

JMA-9100 Instruction Manual > B.DRAWINGS > B.5 Block Diagram of Scanner UnitB－15BB.5.1 NKE-2103Fig B-13: Block Diagram of NKE-2103SLOT ANTENNAMOTORB101SAFETY SWITCHS101MAGV101PULSETRANSSWITCHINGCIRCUITPC201MHGENERATORAVRINTERFACE CIRCUITPC1001MICIF AMPVIDEO AMPRECEIVERReceiver BandwidthControlTune ControlΦA,ΦB,ΦZFILTERDUMMYLOADDC+24VSerial Com, BP, BZ, VD, TRIGNKE-2103 Scanner UnitPOWER SUPPLYCIRCUITMOTOR CONTROLPOWERPC1501Rotation ControlSpeed controlStatusDC+24VTx Trigger/Pulse WidthDC+24VDIODELIMITERENCODERROTARYJOINT

B－16JMA-9100 Instruction Manual > B.DRAWINGS > B.5 Block Diagram of Scanner UnitB.5.2 NKE-2254Fig B-14: Block Diagram of NKE-2254SLOT ANTENNAMOTORB101SAFETY SWITCHS101MAGV101PULSETRANSSWITCHINGCIRCUITPC201MHGENERATORAVRPC1001ΦA,ΦB,ΦZFILTERDUMMYLOADDC+24VSerial Com, BP, BZ, VD, TRIGNKE-2254 Scanner UnitPOWER SUPPLYCIRCUITMOTOR CONTROLPOWERPC1501Rotation ControlSpeed controlStatusDC+24VTx Trigger/Pulse WidthDC+24VENCODERROTARYJOINTINTERFACE CIRCUITPC1101RF AMPIF AMPVIDEO AMPRECEIVERReceiver BandwidthControlTune ControlDIODELIMITER

JMA-9100 Instruction Manual > B.DRAWINGS > B.5 Block Diagram of Scanner UnitB－17BB.5.3 NKE-1125/NKE-1130Fig B-15: Block Diagram of NKE-1125/NKE-1130SLOT ANTENNAROTARYJOINT ENCODERMOTORB101SAFETY SWITCHS101MAGV101PULSETRANSSWITCHINGCIRCUITPC201MHGENERATORAVR INTERFACE CIRCUITPC1101PC1001DIODELIMITERRF AMPIF AMPVIDEO AMPRECEIVERReceiver BandwidthControlTune ControlTx Trigger/Pulse WidthΦA,ΦB,ΦZFILTERDUMMYLOADMOTORDRIVERPC1501AC100/110/220 /230V50/60Hz,1φDC+48VSerial Com, BP, BZ, VD, TRIGNKE-1130/NKE-1125 Scanner UnitPOWER SUPPLYCIRCUITMOTOR RELAYPC1201Relay ControlERRORStatus

B－18JMA-9100 Instruction Manual > B.DRAWINGS > B.5 Block Diagram of Scanner UnitB.5.4 NKE-1129, NTG-3225 / NKE-1139, NTG-3230Fig B-16: Block Diagram of NKE-1129, NTG-3225 / NKE-1139, NTG-3230 SLOT ANTENNAENCODERMOTORB101SAFETY SWITCHS101MAGV101PULSETRANSINTERFACE CIRCUITPC1101DIODE LIMITER/ TRHPL PIN ATT(X-band)RF AMPIF AMPVIDEO AMPReceiver BandwidthControlTune ControlΦA,ΦB,ΦZDUMMYLOAD MOTOR DRIVERPC1501AC100/110 /220/230V50/60Hz,1φDC+48VSerial Com, BP, BZ, VD, TRIGNKE-1139/NKE-1129 Scanner UnitNTG-3230/NTG-3225Transceiver UnitSWITCHINGCIRCUITPC201MHGENERATORPC1001POWER SUPPLYCIRCUITRECEIVERERRORMOTOR RELAYPC1201Relay ControlAC100/110/220/230V50/60Hz,1φROTARYJOINTStatusFILTERAVRTx Trigger/Pulse Width

JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner UnitB－19BB.6 Interconnection Diagram of Scanner Unit

B－20JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner UnitB.6.1 NKE-2103Fig B-17: Interconnection Diagram of NKE-2103 NKE-2103 / 2103HS空中線機内接続図SCANNER UNIT INTERCONNECTIONCAX-10E101NJT1969A301NJS6930ANTENNA NAX-16B-4/6FILTERDUMMYA1011.TUNE2.+5V3.GND4.NC5.IFIF AMP CIRCUIT (PC301)CAE-529-1MAGMAGNETRONV101MAF1565NPOWER SUPPLY CIRCUIT (PC1001)CBD-17831.2A2.1AJ1001J20115.NC4.PW15.MCT6.MBK7.+15V8.AGND9.-7V10.BP11.HSP1.MPS2.PW33.PW212.TI13.+8V14.MOD IDT201-16T201-151.MH3.MNJ1003J2024.HTER1.TIY2.AGND3.MAG.I5.HVER6.C27.BZJ2034.PMS1.PTI2.PTE3.LVR5.GND6.TXI7.TXE1.2A2.1AJ36.AGNDJ14.AGND1.E TIY2.AGND3.EXBP5.ＥＸＢＺSAFETY SWITCHWS101MODULATOR CIRCUIT (PC201)CME-３６３J30115.NC4.PW15.MCT6.MBK7.+15V8.AGND9.-7V10.BP11.HSP1.MPS2.PW33.PW212.TI13.+8V14.MOD IDJ3024.HTER1.TIY2.AGND3.MAG.I5.HVER6.C27.BZJ3034.PMS1.PTI2.PTE3.LVR5.GND6.TXI7.TXE4.COM-1.VD2.VDE3.COM+J2J181.HMCNT2.+15V3.GNDSEB102J84.PMS1.PTI2.PTE3.LVR5.E6.TXI7.TXE4.ΦB1.ΦZ2.E3.ΦA5.+12V6.F.G.YELBLKBLUWHTREDSHIELDDISPLAY UNITP8 1.PTI2.PTE1.LVR2.PMS3.E3.TXI4.TXEJ81J82P81P82WHTBLKBLUREDBLKWHTBRNPMNJU-857ZCRD1280※DISPLAY UNITDISPLAY UNIT1.2A2.1AJ15031.MPS2.MCTJ15013.MBK1.HMCNT2.+15VJ15053.AGND1.2A2.1AJ41.2A2.1AJ51.MPS2.MCTJ2093.MBK1.C2G2.C2J2101.2A2.1AJ204J2061.MH3.MNMOTOR CONTROL POWER CIRCUIT (PC1501)CBD-17791.MCNT+J1253.NC1.M+2.NCJ15023.M-4.NC2.MC NT-MOTORB101H-7BDRD0048MORTOR CBP-202BREAK CIRCUIT CFA-252YEL G RNA103RECEIVER UNIT　ＮＲＧ－６１０MICS.G.S.G.(W204)ZCRD1312※(W110) ZCRD1307※(W107)ZCRD1304※(W103)ZCRD13 06※(W105)ZCRD1300※ZCRD1302※(W101)ZCRD1289※(W102)ZCRD1290※(W10６)ZCRD1303※(W111)ZCRD1308※(W108)ZCRD1305※(OPTION）5421J208D.L1.MS12.NCJ15043.MS2TRANSMITTER/RECEIVER UNIT　ＮZT－２１０３ TRANSMITTER/RECEIVER UNIT INTER C ON NE CTIO NCMK-5998.NC(W104)ZCRD1301※J2051.+15V2.+12V3.+8V4.AGND5.-15V6.X17.X28.+5V9.HTER10.HVERJ10021.+15V2.+12V3.+8V4.AGN D5.-15V6.X17.X28.+5V9.HTER10.HVERWV101A102(RECEIVER UNIT INTERCONNECTION CMA-823)ENCODER CHT -71ANJC4002FCX68 FCX68S.G.CFR-234MAG FILTER CIRCUIT100pF×3A104NJC9952TB11-2short : Nomal Speed2-3short : High SpeedH-7 ZCRD#### *:“#” means specifi cation do cu ment No.“*” means revisi on of the specfi cation docume nt.

JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner UnitB－21BB.6.2 NKE-2254Fig B-18: Interconnection Diagram of NKE-2254 NKE-2254 / 2254HS空中線機内接続図14.VDE12.VD_DC15.VD9.TGT10.TGTE13.TNL11.TNI1.BS32.BS23.BS14.TNC5.+5V6.-15V7.+15VRECEIVER UNIT NRG-162ARECEIVER CIRCUIT CMA-866AJ101BM15B-XASS-TET/R CONTROL CIRCUITCMC-1205R1.MONI2.GS3.GSE4.TGT5.TGTE6.TNL7.-15V8.TNI9.+15V10.GND11.TRG21.BS32.BS23.BS14.TNC5.MicPS6.VDINE7.VDIN8.+5V1.RXD2.TXD3.+5V4.GND1.SHORT2.MAG I3. X 14. X 25.T I6.T IE7.+15V8.GND9.NC10.NC11.NC12.NC1.HMCNT2.+15V3.GND1.+15V2.+12V3.GND4.GND5.-15V6.10V7.10VE8.+5V1.MC T2.MBK3.TISTOP4.G ND5.MPS6. MI E R1. T IY2.TIYE3.BP4.BPE5.BZ6.BZE1.+12V2.GN D3.FAN_ERR11.HTER12.HVGATE13.TISTOP14.GND5.CNT6.+5V7.+15V8.STABY_REQ9.NC1.PW12.PW23.PW34.+24V5.GN D1.BP+2.BP-3.BZ+4.BZ-5.TRIG+6.TRIG-7.MTR+8.MTR-9.MTRE10.VD+11.VD-1.V D2.V DE3.MTR+4.MTR-J1118J1103J1104 J1111J1191J1110J1109TB101J8 J1106J1112 J1113IL -G - 1 2PIL-G-8P IL-G-11PB6P-SHFIL-G-9PMSTBA2.5/11-GIL-G-5PB3P-SHFIL-4PB8P-SHFIL-G-3PMAGPOWER SUPPLY CIRCUITCBD-1682A1.+15V2.+12V3.+8V4.GND5.-15V6.X17.X28.+5V1.M C T2.MBK3.H S P4.H T ER5.TISTOP6.C 27.GND8.M P S9.M I ER2.1A1.2A2.1A1.2A2.1A1.2A1.MH2.NC3.MN1.MH2.NC3.MN1.X12.X2No.2No.1214356FILTERJ1004 J1003J 5J 4 J 3J1001J1002J2102J210 1J2103ANTENNA1. S HO R T2.MAG I3. X 14. X 25. T I6. T IE7.+15VB9P-SHF B8P-SHF1586514-2350209-1IL-10P350209-2350209-1350428-1MODULATOR CIRCUITCPA-264MODULATOR UNIT INTERCONNECTIONCMB-404D.L①②③①②③ﾐﾄﾞﾘｷC2010.0 1UF 1K VC2020.22UF 200VR202 2.7KΩ1/2WC2030.22UF200VT1 R201150Ω8WH-7LPRD0122CD202 CD201MD-12N1MD-12N1Ａ101 Ａ102M1568BSＶ101P3001P1109 P1110P1104P1103 P1003P1004P1111PULSE TANSP2103DUMMYＡ103(W001)(W003)P10021.+12V2.GND3.FAN_ERR2J1114IL-G-3P1.+12V2.C2J1105IL-G-2PP1105MODULATOR UNIT NMA-550SCANNER UNIT INTERCONNECTIONCAX-15(W106)(W103)(W104)(W105)ZCRD1255※ZCRD1257※P1505J1IL-G-6PJ2IL- G -4PZCRD1256※Ａ301NJS6930ZCRD1252※ZCRD1258※ZCRD1251※ZCRD1253※(W004)(W207)ZCRD1448※ZCRD1254※1.φZ2.φZE3.φ A4.φB5.+12V6.GNDJ13IL-6P50/60ｋWREDWHTDISPLAY UNITP2101P21028.GND1.M+2.M-1586514-2NJC40029.NC10.NCB02P-NV(LF)(SN）S. G.S.G.S.G.8.G ND1234567891012345678910WHTBLKP1118BLUWHTBLKBLUP1301J1301(W006)1234123456567878SEYE LBLKBLUWHTREDSHIELDB102ENCODER CHT-71AP13(W017)FANREDBLUYELB201B202FANREDBLUYEL(W009)(W010)P1113 P1114REDWHTZCRD1447※(W206)ｼﾛｸﾛｱｵ12BLK.T21 33BLK.T(W107)ZCRD1259※J1303P1303P1302J1302(W201)ZCRD1260※1.PTI2.P T E3.LVR4.PMS5.GN D6.TXI7. T X E8.NCIL-8P1.PTI2.PTE1.LVR2.PMS3.E3.TXI4.TXEJ82J81PMP81P82WHTBLKBLUREDBLKWHTBRNNJU-85ZCRD1280※(W018)ZCRD1277※S.G.S101S-32217548CBD-1779IL-3P-S3EN2J15051.H MC N T2.+15V3.EJ15041. M S 12.NC3.MS2ｱｶ太P1504B3 P- V HP1501J15011.MPS2.MCTIL- G -3 P- S3 T 2 -SA(W302)ZCRD1449※(W307)J1503IL-2P-S3EN2R1 10Ω ,1 0WP1503ZCRD1450※GRNBRNBLU.TMOTOR CBP-168A / CBP-182YE L1.M+2.NC3.M-4.NCB4P-VHP1502J1251.M CN T -2.M CN T +3.NCP125B3P-SHF-1AAP1502B101MOTOR CONTROL POWER CIRCUIT(W305)(W301)BLK.TDISPLAY UNITMOTORBREAK CIRCUITCFA-257NJC3901M NJC3901MH-7BFRD0002H-7BFRD0002NJC9952Ａ104SAFETY SWITCHCSD-6531.2A2.1A1.2A2.1AJ4350209-1J5350209-13.MBKZCRD1451※(W208)ZCRD1494※(W308※NKE-2254HS・MOTOR CBP-182UVUTHUVUTHTH101WHT.TTR101（100W）ｼﾛ太HEATER CONTROL PARTCHG-216（OPTION）TB105S.G.CFR-229MAG FIL TER CIRCUIT220pF×5ZCRD1508※(W401)H-7ZCRD####*:“#” means speci fication document No.“*” means revision of the specficatio n document.

B－22JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner UnitB.6.3 NKE-1125 (AC110V)Fig B-19: Interconnection Diagram of NKE-1125 (AC110V) NKE-1125PM (AC100V)空中線機内接続図14.VDE12.VD_DC15.VD9.TGT10.TGTE13.TNL11.TNI1.BS32.BS23.BS14.TNC5.+5V6.-15V7.+15VRECEIVER UNIT NRG-162ARECEIVER CIRCUIT CMA-866AJ101BM15B-XASS-TET/R CONTROL CIRCUITCMC-1205R1.MONI2.GS3.GSE4.TGT5.TGTE6.TNL7.-15V8.TNI9.+15V10.GND11.TRG21.BS32.BS23.BS14.TNC5.MicPS6.VDINE7.VDIN8.+5V1.RXD2.TXD3.+5V4.GND1.SHORT2.M AG I3. X 14. X 25. T I6. T IE7.+15V8.GND9.NC10.NC11.NC12.NC1.HMCNT2.+15V3.GND1.+15V2.+12V3.GND4.GND5.-15V6.10V7.10VE8.+5V1.MC T2.MBK3.TISTOP4.G ND5.MPS6. MI E R1. T IY2.TIYE3.BP4.BPE5.BZ6.BZE1.+12V2.GN D3.FAN_ERR11.HTER12.HVGATE13.TISTOP14.GND5.CNT6.+5V7.+15V8.STABY_REQ9.NC1.PW12.PW23.PW34.+24V5.GN D1.BP+2.BP-3.BZ+4.BZ-5.TRIG+6.TRIG-7.MTR+8.MTR-9.MTRE10.VD+11.VD-1.VD2.VDE3.MTR+4.MTR-J1118J1103J1104 J1111J1191J1110J1109TB101J8 J1106J1112 J1113IL -G - 1 2PIL-G-8P IL-G-11PB6P-SHFIL-G-9PMSTBA2.5/11-GIL-G-5PB3P-SHFIL-4PB8P-SHFIL-G-3PMAGPOWER SUPPLY CIRCUITCBD-1682A1.+15V2.+12V3.+8V4.GND5.-15V6.X17.X28.+5V1.MC T2.MBK3. HS P4. HT E R5.TISTOP6.C 27.GND8.MPS9. MI E R2.1A1.2A2.1A1.2A2.1A1.2A1.MH2.NC3.MN1.MH2.NC3.MN1. X 12. X 2No.2No.1214356FILTERJ1004 J1003J 5J 4 J 3J1001J1002J2102J2101J2103ANTENNA1. SH O R T2.MA G I3.X14.X25.TI6.TIE7.+15VB9P-SHF B8P-SHF1586514-2350209-1IL-10P350209-2350209-1350428-1MODULATOR CIRCUITCPA-264MODULATOR UNIT IN T ERCO N NECTI ONCMB-404D.L①②③①②③GRNYELC2010.01UF 1KVC2020.22UF 200VR202 2.7KΩ1/2WC2030.22UF200VT1 R201150Ω8WH-7LPRD0122CD202 CD201MD-12N1MD-12N1NJC3901MＡ101 Ａ102P3001P1109 P1110P1104P1103 P1003P1004P1111PULSE TRANSP3P2103DUMMYA103(W001)(W003)P10021.+12V2.GND3.FAN_ERR2J1114IL-G-3P1.+12V2.C2J1105IL-G-2PP1105MODULATOR UNIT NMA-550SCANNER UNIT INTERCONNECTIONCAX-11(W106)(W103)(W104)(W105)ZCRD1255※ZCRD1257※J1IL-G-6PJ2IL- G -4PZCRD1256※A301NJS6930ZCRD1252※ZCRD1258※ZCRD1251※ZCRD1253※(W004)(W207)ZCRD1263※ZCRD1254※1.φZ2.φZE3.φ A4.φB5.+12V6.GNDJ13IL-6P50/60ｋWｱｶｼﾛDISPLAY UNITP2101P21028.GND1.M+2.M-1586514-2NJC40029.NC10.NCB02P-NV(LF)(SN ）S. G.S.G.S.G.8.G ND1234567891012345678910WHTBLKP1118BLUWHTBLKBLUP1301J1301(W006)1234123456567878SEYELBLKBLUWHTREDSHIELDB102ENCODER CHT-71AP13(W017)FANREDBLUYELB201B202 FANREDBLUYELP1113 P1114REDWHTZCRD1262※(W206)12BLK.T21 33BLK.T(W107)ZCRD1259※J1303P1303P1302J1302(W201)ZCRD1260※W101W1011.PTI2.P T E3.LVR4.PMS5.GN D6.TXI7. T X E8.NCIL-8P1.PTI2.PTE1.LVR2.PMS3.E3.TXI4.TXEJ82J81PMP81P82WHTBLKBLUREDBLKWHTBRNNJU-85ZCRD1280※(W018)ZCRD1277※X25kW,2ﾕﾆｯﾄS.G.NJC3901MH-7BFRD0002H-7BFRD0002M1568BSＶ101NJC9952Ａ104CFR-229MAG FILTER CIRCUITS.G.220pF×5HEATER CONTROL PARTCHG-216（OPTION）+48V+48VGU1V1W1U1W1V1DISPLAY UNITTB102+48V+48VG(W301)S101S-32F217548RED.T RED.TBLK.TBLK.TZCRD1264※(W302)ZC RD 12 65※+12VZCRD1261※(W203)SAFETY SWITCHCSD-654to CCB-655 J1941ZCRD1537※(W308)UVUTHUVUTHTH101W401 7ZCRD1508※TR101（100W）TB105WHT.TWHT.TWHTBLKBLUZCRD1454※(W305)P1212BRAKE CIRCUITCFA-253J15011.VERR2.EH-7EPRD0035B201J1505PC1501P1501B2P-VHP1505P1201RELAY FIL TER CIRCUITCSC-656PC1201IL-3P1.HMCNT2.+15V3.G NDP1211J12121.VERR12.EJ1201J12111.U13.V12.NC4.NCB4P-VHIL-2P1.VERR12.E1.VERR2.E1.P2.NC3.N1.P2.N1.BKH13.BKH11.BKS12.BKS21.+12V2.NC3.+12VEP1941 J1941J1903P1903J1905P1905J1912 P1912BRAKE CONTROL CIRCUITCCB-655P1502J1921P1921J1911P1911to TB102REDBLKIL-2PB2PS-VHS3B-XH-A1-350210-0 1-350209-01-480700-0ZC RD 15 37※(W308)ZCRD1536※(W307)ZCRD1452※(W303)WC1ZCRD1538※(W309)ZCRD1539※(W310)CBP-203H-7BDRD00502.NC4.NC1.S12.S23.S34.S45.S56.S6J1502J15033.M21.M15.M3P1503MOTORMOTORB101BRAKE CIRCUIT BCFA-260BRAKE CIRCUIT ACFA-259R1R2R3R4R1120Ω30W330Ω30W×4×12.NC3.MV21.MU22.NC4.NC5.NC6.G N DB6P-VH(W304)ZCRD1314※R1R2P15041.R13.R2J1504B3P-VH2.NCP12021.MU23.MV2J12022.GNDB3P-NV1.2kΩ30W×2AC100V MOTOR DRIVERCBD-2001

JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner UnitB－23BB.6.4 NKE-1125 (AC220V)Fig B-20: Interconnection Diagram of NKE-1125 (AC220V) NKE-1125PM (AC220V)空中線機内接続図14.VDE12.VD_DC15.VD9.TGT10.TGTE13.TNL11.TNI1.BS32.BS23.BS14.TNC5.+5V6.-15V7.+15VRECEIVER UNIT NRG-162ARECEIVER CIRCUIT CMA-866AJ101BM15B-XASS-TET/R CONTROL CIRCUITCMC-1205R1.MONI2.GS3.GSE4.TGT5.TGTE6.TNL7.-15V8.TNI9.+15V10.GND11.TRG21.BS32.BS23.BS14.TNC5.MicPS6.VDINE7.VDIN8.+5V1.RXD2.TXD3.+5V4.GND1.SHORT2.M AG I3. X 14. X 25. T I6. T IE7.+15V8.GND9.NC10.NC11.NC12.NC1.HMCNT2.+15V3.GND1.+15V2.+12V3.GND4.GND5.-15V6.10V7.10VE8.+5V1.MC T2.MBK3.TISTOP4.G ND5.MPS6. MI E R1. T IY2.TIYE3.BP4.BPE5.BZ6.BZE1.+12V2.GN D3.FAN_ERR11.HTER12.HVGATE13.TISTOP14.GND5.CNT6.+5V7.+15V8.STABY_REQ9.NC1.PW12.PW23.PW34.+24V5.GN D1.BP+2.BP-3.BZ+4.BZ-5.TRIG+6.TRIG-7.MTR+8.MTR-9.MTRE10.VD+11.VD-1.VD2.VDE3.MTR+4.MTR-J1118J1103J1104 J1111J1191J1110J1109TB101J8 J1106J1112 J1113IL -G - 1 2PIL-G-8P IL-G-11PB6P-SHFIL-G-9PMSTBA2.5/11-GIL-G-5PB3P-SHFIL-4PB8P-SHFIL-G-3PMAGPOWER SUPPLY CIRCUITCBD-1682A1.+15V2.+12V3.+8V4.GND5.-15V6.X17.X28.+5V1.MC T2.MBK3. HS P4. HT E R5.TISTOP6.C 27.GND8.MPS9. MI E R2.1A1.2A2.1A1.2A2.1A1.2A1.MH2.NC3.MN1.MH2.NC3.MN1. X 12. X 2No.2No.1214356FILTERJ1004 J1003J 5J 4 J 3J1001J1002J2102J2101J2103ANTENNA1. SH O R T2.MA G I3.X14.X25.TI6.TIE7.+15VB9P-SHF B8P-SHF1586514-2350209-1IL-10P350209-2350209-1350428-1MODULATOR CIRCUITCPA-264MODULATOR UNIT IN T ERCO N NECTI ONCMB-404D.L①②③①②③GRNYELC2010.01UF 1KVC2020.22UF 200VR202 2.7KΩ1/2WC2030.22UF200VT1 R201150Ω8WH-7LPRD0122CD202 CD201MD-12N1MD-12N1NJC3901MＡ101 Ａ102P3001P1109 P1110P1104P1103 P1003P1004P1111PULSE TRANSP3P2103DUMMYA103(W001)(W003)P10021.+12V2.GND3.FAN_ERR2J1114IL-G-3P1.+12V2.C2J1105IL-G-2PP1105MODULATOR UNIT NMA-550SCANNER UNIT INTERCONNECTIONCAX-11(W106)(W103)(W104)(W105)ZCRD1255※ZCRD1257※J1IL-G-6PJ2IL- G -4PZCRD1256※A301NJS6930ZCRD1252※ZCRD1258※ZCRD1251※ZCRD1253※(W004)(W207)ZCRD1263※ZCRD1254※1.φZ2.φZE3.φ A4.φB5.+12V6.GNDJ13IL-6P50/60ｋWｱｶｼﾛDISPLAY UNITP2101P21028.GND1.M+2.M-1586514-2NJC40029.NC10.NCB02P-NV(LF)(SN ）S. G.S.G.S.G.8.G ND1234567891012345678910WHTBLKP1118BLUWHTBLKBLUP1301J1301(W006)1234123456567878SEYELBLKBLUWHTREDSHIELDB102ENCODER CHT-71AP13(W017)FANREDBLUYELB201B202 FANREDBLUYELP1113 P1114REDWHTZCRD1262※(W206)12BLK.T21 33BLK.T(W107)ZCRD1259※J1303P1303P1302J1302(W201)ZCRD1260※W101W1011.PTI2.P T E3.LVR4.PMS5.GN D6.TXI7. T X E8.NCIL-8P1.PTI2.PTE1.LVR2.PMS3.E3.TXI4.TXEJ82J81PMP81P82WHTBLKBLUREDBLKWHTBRNNJU-85ZCRD1280※(W018)ZCRD1277※X25kW,2ﾕﾆｯﾄS.G.NJC3901MH-7BFRD0002H-7BFRD0002M1568BSＶ101NJC9952Ａ104CFR-229MAG FILTER CIRCUITS.G.220pF×5HEATER CONTROL PARTCHG-216（OPTION）+48V+48VGU1V1W1U1W1V1DISPLAY UNITTB102+48V+48VG(W301)S101S-32F217548RED.T RED.TBLK.TBLK.TZCRD1264※(W302)ZC RD 12 65※+12VZCRD1261※(W203)SAFETY SWITCHCSD-654to CCB-655 J1941ZCRD1537※(W308)UVUTHUVUTHTH101W401 7ZCRD1508※TR101（100W）TB105WHT.TWHT.TWHTBLKBLUZCRD1454※(W305)P1212BRAKE CIRCUITCFA-253J15011.VERR2.EH-7EPRD0034B201J1505PC1501P1501B2P-VHP1505P1201RELAY FIL TER CIRCUITCSC-656PC1201IL-3P1.HMCNT2.+15V3.G NDP1211J12121.VERR12.EJ1201J12111.U13.V12.NC4.NCB4P-VHIL-2P1.VERR12.E1.VERR2.E1.P2.NC3.N1.P2.N1.BKH13. BK H 21.B K S12.BKS21.+12V2.NC3.+12VEP1941 J1941J1903P1903J1905P1905J1912 P1912BRAKE CONTROL CIRCUITCCB-655P1502J1921P1921J1911P1911to TB102REDBLKIL-2PB2PS-VHS3B-XH -A1-350210-0 1-350209-01-480700-0ZC RD 15 37※(W308)ZCRD1536※(W307)ZCRD1452※(W303)WC1ZCRD1538※(W309)ZCRD1539※(W310)CBP-203H-7BDRD00502.NC4.NC1.S12.S23.S34.S45.S56.S6J1502J15033.M21.M15.M3P1503MOTORMOTORB101BRAKE CIRCUIT BCFA-260BRAKE CIRCUIT ACFA-259R1R2R3R4R1120Ω30W330Ω30W×4×12.NC3.MV21.MU22.NC4.NC5.NC6.G N DB6P-VH(W304)ZCRD1314※R1R2P15041.R13.R2J1504B3P-VH2.NCP12021.MU23.MV2J12022.GNDB3P-NV1.2kΩ30W×2AC220V MOTOR DRIVERCBD-2000

B－24JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner UnitB.6.5 NKE-1129 (AC110V)Fig B-21: Interconnection Diagram of NKE-1129 (AC110V) NKE-1129PM (AC100V)空中線機内接続図SCANNER UNIT INTERCONNECTIONCAX-12J82J81 P81P82WHTBLKBLUREDBLKWHTBRNU1V1W1+12VC2ΦZEΦZΦAEΦBREDSHIELDYELBLUWHTSEB102BLKBLKENCORDER CHT-71A1C102C1012200p50V1000μ16V+S101S-32217548RED.TBLK.TREDPTIPTELVRPMSETXITXEVERR1EWHTRED.TBLK.TTRANSCEIVER UNITTRANSCEIVER UNIT11BLUREDBLKPMNJU-85ZCRD1280※TB103TB104（W301) ZCRD1285※（W303) ZCRD1278※SAFETY SWITCH CSD-655（W302) ZCRD1286※S.G.S.G.S.G .S.G.Xﾊﾞﾝﾄﾞ, 3ﾕﾆｯﾄTRANSCEIVER UNIT（W305)ZCRD1455※TH101TR101（100W）WHT.THEATER CO NTROL P ARTCHG-216(OPTION)UVUTHAC100VTB105W401 7ZCRD1508※WHT.TWHT.TZCRD1548※1.VERR12.E1.VER R2.E1.P2.NC3.N 1.BKH13.BK H21.BKS12.BKS21.+12V2.NC3.+12VEP1941 J1941J1903P1903J1905P1905J1912P1912BRAKE CONTROL CIRCUITCCB-655J1921P1921J1911P19111.RED3.BLKIL-2PS3B-XH-A1-350210-0 1-350209-0ZCRD1547※(W307 )ZCRD1538※(W309)ZCRD1539※(W310)CBD-2001BRAKE CIRCUITCFA-253J15011.VERR2.EH-7EPRD0035B201J1505PC1501P1501B2P-VH1.P2.NP1502AC100VWC1CBP-203H-7BDRD00502.NC4.NC1.S12.S23.S34.S45.S56.S6J1502J15033.M21.M15.M3P1503MOTORMOTORB101(W308)MOTOR DRIVERBRAKE CIRCUIT BCFA-260BRAKE CIRCUIT ACFA-259R1R2R3R4R1120Ω30W330Ω30W×4×12.NC3.M V 21.MU22.N C4.N C5.N C6.GNDB6P-VH1.2kΩ30W1.2kΩ30W(W304)ZCRD1314※R1R2P15041.R 13.R2J1504B3P-VH2.NC

JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner UnitB－25BB.6.6 NKE-1129 (AC220V)Fig B-22: Interconnection Diagram of NKE-1129 (AC220V) NKE-1129PM (AC220V)空中線機内接続図SCANNER UNIT INTERCONNECTIONCAX-12J82J81 P81P82WHTBLKBLUREDBLKWHTBRNU1V1W1+12VC2ΦZEΦZΦAEΦBREDSHIELDYELBLUWHTSEB102BLKBLKENCORDER CHT-71A1C102C1012200p50V1000μ16V+S101S-32217548RED.TBLK.TREDPTIPTELVRPMSETXITXEVERR1EWHTRED.TBLK.TTRANSCEIVER UNITTRANSCEIVER UNIT11BLUREDBLKPMNJU-85ZCRD1280※TB103TB104（W301) ZCRD1285※（W303) ZCRD1278※SAFETY SWITCH CSD-655（W302) ZCRD1286※S.G.S.G.S.G .S.G.Xﾊﾞﾝﾄﾞ, 3ﾕﾆｯﾄTRANSCEIVER UNIT（W305)ZCRD1455※TH101TR101（100W）WHT.THEATER CO NTROL P ARTCHG-216(OPTION)UVUTHAC100VTB105W401 7ZCRD1508※WHT.TWHT.TZCRD1548※1.VERR12.E1.VER R2.E1.P2.NC3.N 1.BKH13.BK H21.BKS12.BKS21.+12V2.NC3.+12VEP1941 J1941J1903P1903J1905P1905J1912P1912BRAKE CONTROL CIRCUITCCB-655J1921P1921J1911P19111.RED3.BLKIL-2PS3B-XH-A1-350210-0 1-350209-0ZCRD1547※(W307 )ZCRD1538※(W309)ZCRD1539※(W310)CBD-2000BRAKE CIRCUITCFA-253J15011.VERR2.EH-7EPRD0034B201J1505PC1501P1501B2P-VH1.P2.NP1502AC220VWC1CBP-203H-7BDRD00502.NC4.NC1.S12.S23.S34.S45.S56.S6J1502J15033.M21.M15.M3P1503MOTORMOTORB101(W308)MOTOR DRIVERBRAKE CIRCUIT BCFA-260BRAKE CIRCUIT ACFA-259R1R2R3R4R1120Ω30W330Ω30W×4×12.NC3.M V 21.MU22.N C4.N C5.N C6.GNDB6P-VH1.2kΩ30W1.2kΩ30W(W304)ZCRD1314※R1R2P15041.R 13.R2J1504B3P-VH2.NC

B－26JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner UnitB.6.7 NTG-3225Fig B-23: Interconnection Diagram of NTG-3225 NTG-3225送受信機機内接続図14.VDE12.VD_DC15.VD9.TGT10.TGTE13.TNL11.TNI1. BS 32. BS 23. BS 14. T NC5.+5V6.-15V7.+15VRECEIVER UNIT NRG-162ARECEIVER CIRCUIT CMA-866AJ101BM15B-XASS-TET/R CONTROL CIRCUITCMC-1205R1. MO N I2.GS3.GSE4.TGT5.TGTE6.TNL7.-15V8.TNI9.+15V10.GND11.TRG21.BS32.BS23.BS14.TNC5.MicPS6.VDINE7.VDIN8.+5V1.RXD2.TXD3.+5V4.GND1. S HO RT2.MAGI3. X 14. X 25. T I6. T IE7.+15V8.GND9.NC10.NC11.NC12.NC1.HMCN T2.+15V3.GND1.+15V2.+12V3.G ND4.GND5.-15V6.10V7.10VE8.+5V1.MCT2.MBK3. T IS TO P4.GND5.MPS6.MIE R1.TIY2.TIYE3.BP4.BPE5.BZ6.BZE1.+12V2.GND3.FAN_ERR11.HT ER 12. HV GA T E13. T IS T O P14.GN D5.CN T6.+5V7.+15V8. S T A BY _R E Q9.NC1.PW12.PW23.PW34.+24V5.GND1.PTI2.PTE3.LVR4.PMS5.GND6.TXI7.TXE8.NC1. BP +2. BP -3.BZ +4.BZ -5.TRIG+6.TRIG-7.MTR+8.MTR-9. MT R E10.VD+11.VD-1.VD2.VDE3.M T R+4.M T R-J1118J1103J1104 J1111J1191J1110J1109TB101J8 J1106J1112 J1113IL-G-12PIL-8PIL-G-8P IL-G-11PB6P-SHFIL-G-9PMSTBA2.5/11-GIL- G -5PB3P-SHFIL-4PB8P-SHFIL-G-3PMAGPOWER SUPPLY CIRCUITCBD-1682A1.+15V2.+12V3.+8V4.GND5.-15V6.10V7.10VE8.+5V1.MCT2.MBK3.HSP4.HT ER5. T IS TO P6.C27.G ND8.MPS9.MIE R2.1 A1.2 A2.1 A1.2 A2.1 A1.2 A1.MH2.NC3.MN1.MH2.NC3.MN1. X 12. X 2No.2No.1214356FILTERJ1004 J1003J 5J 4 J 3J1001J1002J2102J2101J2103ANTENNA1.S H O R T2.M AG I3.X 14.X 25.T I6.T IE7.+15VB9P-SHF B8P-SHF1586514-2350209-1IL-10P350209-2350209-1350428-1MODULATOR CIRCUITCPA-264MODULATOR UNIT INT ERC ONN ECTIONCMB-405D.L①②③①②③ﾐﾄﾞﾘｷC2010.01UF 1KVC2020.22UF 200VR202 2.7KΩ1/2WC2030.22UF200VT1 R201150Ω8WH-7LPRD0122CD202 CD201MD-12N1MD-12N1NJC3901M NJC3901MＡ101 Ａ102P3001P1109 P1110P110 4P1103 P1003P1004P1111PULSE TRANSW201BLK.TP3P2103P1118DUMMYA103(W001)(W003)(W006)P10021.+12V2.GND3.FAN_ERR2J1114IL-G-3P1.+12V2.C 2J1105IL-G-2PP1105MODULATOR UNITNMA-552P8TRANSCEIVER UNIT INTERCONNECTIONCMK-593(W106)(W103)(W104)(W105)ZCRD1242※ZCRD1244※P1212J1IL-G-6PJ2IL-G-4PPTIPTELVRPMSETXITXEEVERRVD+VD-TRIG+TRIG-BP+BP -/ BZ-BZ+MTREMTR-MTR+TB201 TB204(W301)ZCRD1248※ZCRD1243※(W302)ZCRD1249※Ａ301NJS6930PINＡ302NJS6926ZCRD1234※ZCRD1245※ZCRD1233※ZCRD1246※ZCRD1235※(W004)(W005)ZCRD1236※ZCRD1237※1.φ Z2.φZE3.φA4.φ B5.+12V6.GNDJ13IL-6P50/60ｋWBLKREDBLKREDU1V1U0V0U1U0V1V0+12VC2φZEφZφAEφB+48V+48V+48VGRED.TWHT.TREDWHT(W008) ZCRD1239※ANTENNAANTENNADISPLAY UNITANTENNA DISPLAY UNIT(W203) ZCRD1247※(W007) ZCRD1238※HC3L23L13L13L2TB203TB202P2101P2102P1018.GND(W014)ZCRD1241※1.M+2.M-(W013) ZCRD1240※1586514-2NJC40029.NC10.NCB02P-NV(LF)(SN）S.G.S. G .S.G.8.G N DDISPLAY UNIT(W303) ZCRD1483※RELAY FILTER CIRCUITCSC-656PC1201IL - 3P1.HMCNT2.+15V3.GNDP1211P12021.MU2J12121.VERR2.E3.MV2J1202J1201J12111.U13.V12.NC4.NC2.GNDB4P-VHB3P-NVIL-3PIL-2PP1201S.G.M1568BSＶ101NJC9952Ａ104CFR-22 9MAG FILTER CIRCUITS.G.220pF×5+48VGH-7 ZCRD####*:“#” means specifi cation document No.“*” mea ns revisi on of the specfication document.

JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner UnitB－27BB.6.8 NKE-1130 (AC110V)Fig B-24: Interconnection Diagram of NKE-1130 (AC110V) NKE-1130PM　（AC100V)空中線機内接続図1.TGT2.TGTE3.TNL4.-15V5.TNI6.+15V7.GN D1. BS 32. BS 23. BS 14. T NC5.MPS6.VDE7.VDRECEIVER UNIT NRG-229IF CIRCUIT CAE-499J101IL-9PJ102IL-7PT/R CONTROL CIRCUITCMC-1205R1.MONI2.GS3.GSE4.TGT5.TGTE6.TNL7.-15V8.TNI9.+15V10.GND11.TRG21.BS32. BS 23. BS 14. T NC5. M ic P S6.VDINE7.VDIN8.+5V1.RXD2.TXD3.+5V4.GND1. S HO RT2.MAGI3. X 14. X 25. T I6. T IE7.+15V8.GND9.NC10.NC11.NC12.NC1.HMCN T2.+15V3.GND1.+15V2.+12V3.G ND4.G ND5.-15V6.10V7.10VE8.+5V1.MCT2.MBK3. T IS TO P4.GND5.MPS6.MIE R1.TIY2.TIYE3.BP4.BPE5.BZ6.BZE1.+12V2.GND3.FAN_ERR11.HTER12.HVGA T E 13.TISTOP14.GND5.CN T6.+5V7.+15V8.STABY_REQ9.NC1.PW12.PW23.PW34.+24V5.GND1.PTI2.PTE3.LVR4.PMS5.GN D6.TXI7.TXE8.NC1. BP +2. BP -3.BZ +4.BZ -5.TRIG+6.TRIG-7.MTR+8.MTR-9. MT R E10.VD+11.VD-1.VD2.VDE3. MT R +4. MT R -J1118J1103J1104 J1111J1191J1110J1109TB101J8 J1106J1112 J1113IL-G-12PIL-8PIL -G -8P IL-G-11PB6P-SHFIL-G-9PMSTBA2.5/11-GIL- G -5PB3P-SHFIL-4PB8P-SHFIL -G -3 PMAGPOWER SUPPLY CIRCUITCBD-1682A1.+15V2.+12V3.+8V4.GND5.-15V6.10V7.10VE8.+5V1.MCT2.MBK3.HSP4.HTER5.TISTOP6.C27.GND8.MPS9.MIER2.1A1.2A2.1A1.2A2.1A1.2A1.MH2.NC3.MN1.MH2.NC3.MN1.X12.X2No.2No.1214356FILTERJ1004 J1003J 5J 4 J 3J1002J2102J2101J2103ANTTENA1. S HO R T2.MAG I3. X 14. X 25. T I6. T IE7.+15V8.GND9.NC10.NCB9P-SHF B8P-SHFB02P-NV(LF)(SN）350209-1IL-10P350209-2350209-1MODULATOR CIRCUITCPA-264MODULATOR UNIT INTERCONNECTIONCMB-406D.L①②③①②③GRNYELC2010.01UF 1KVC2020.22 U F 2 00 VR202 2.7KΩ1/2WC2030.22UF200VT201 R２01150Ω8WH-7LPRD0122CD202 CD201MD-12N1MD-12N1NJC3316Ａ101M1555Ｖ101R ECEIRVER UNIT INTERCONN ECTIONP3001 P3002P1109 P1110P1104P1103 P1003P1004P1111PULSE TRANS（W201)BLK.TP3P2103P1118DUMMYＡ102H-7ANRD0018(W001) (W002)(W003)(W006)P10021.+12V2.GND3.FAN_ERR2J1114IL-G-3P1.+12V2.C2J1105IL-G-2PP1105MODULATOR UNITNMA-551SCANNER INTERCONNECTIONCAX-13(W106)ZCRD1321※(W103)ZCRD1318※(W104)ZCRD 1319※(W105)ZCRD1320※ZCRD1267※J1IL-G-6PJ2IL-G-4PＡ301NJS6318ZCRD1268※CMA-902ZCRD1266※ZCRD1273※ZCRD1269※（W004）(W005)ZCRD1270※ZCRD1271※50/60ｋWP2101P21028.+5V9.NCRF CIRCUIT CAF-595J1001350428-11.M+2.M-1586514-21586514-2S.G.S.G. S.G.1.φZ2.φZE3.φ A4.φB5.+12V6.GNDJ13IL-6PSEYE LBLKBLUWHTREDSH I ELDB102ENCODER CHT-71AP13(W017)DISPLAY UNITFANREDBLUYELB104B103 FAN(W010)P1113 P1114(W301)TB102S101S-32F239568SAFETY SWITCHCSD-656(W203)ZCRD1274※REDWHTREDBLUYELZCRD1272※P1112J11121.PTI2.PTE1.LVR2.PMS3.E3.TXI4.TXEJ82J81PMP81P82WHTBLKBLUREDBLKWHTBRNNJU-847Z CRD1 27 9 ※(W018)ZCRD1275※(W008)ZCRD1283※S. G.S30kw, 2ﾕﾆｯﾄRED.TRED.TBLK.TBLK.TZCRD1322※(W302)ZCRD1453※S.G.CFR-229MAG FILTER CIRCUIT22 0pF ×5P1201+48V+48VGU1V1W1U1W1V1DISPLAY UNIT+48V+48VG12VU123434VUUTHUTHTH101TR101（200W）HEATER CONTROL PARTCHG-215(OPTION)WHT.TWHT.TW401 7ZCRD1509to CMC-1205R J1112(W308)ZCRD1542※WHTBLKBLUMOTOR DRIVERCBD-2001ZC RD 145 6※(W305)P1212BRAKE CIRCUITCFA-255J15011.V ERR2.EH-7EPRD0035B201J1505PC1501P1501B2P-VHP1505RELAY FILTER CIRCUITCSC-656PC1201IL-3P1.HMCNT2.+15V3.GNDP1211P12021.MU2J12121.VERR12.E3.MV2J1202J1201J12111.U13.V12.NC4.NC2.G N DB4P-VHB3P-NVIL-3PIL-2P1.VERR12.E1.VERR2.E1.P2.NC3.N1. P2. N1.BKH13. BK H 21.BKS12.BKS21.+15V2.NC3.+15VEP1941 J1941J1903P1903J1905P1905J1912P1912BRAKE CONTROL CIRCUITCCB-655P1502J1921P1921J1911P19111.RE D3. BL KJ1511P1511IL-2PS3B-XH-A1-350210-0 1-350209-01-480700-0ZCRD1542※(W308)ZCRD1545※(W311) ZCRD1541※(W307)ZCRD1284※(W303)AC100VWC1ZCRD1543※(W309)ZCRD1544※(W310)BLAKE CIR CUI T BCFA-262BRAKE CIRCUIT ACFA-261R1R2R3R4R1120Ω30W330Ω30W×4×12.NC4.NC1. S 12.S23.S34. S 45.S56.S6J1502J15033.M21.M15.M3P1503MOTORMOTORB101CBP-205H-7BDRD00492.NC(W304)ZCRD1316※R1R21.2kΩ30WP15041.R 13.R2J1504B3P-VH2.NC3.M V 21.M U22.N C4.NC5.N C6.G N DB6P-VHto CCB-655 J1941

B－28JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner UnitB.6.9 NKE-1130 (AC220V)Fig B-25: Interconnection Diagram of NKE-1130 (AC220V) NKE-1130PM　（AC220V)空中線機内接続図1.TGT2.TGTE3.TNL4.-15V5.TNI6.+15V7.GN D1. BS 32. BS 23. BS 14. T NC5.MPS6.VDE7.VDRECEIVER UNIT NRG-229IF CIRCUIT CAE-499J101IL-9PJ102IL-7PT/R CONTROL CIRCUITCMC-1205R1.MONI2.GS3.GSE4.TGT5.TGTE6.TNL7.-15V8.TNI9.+15V10.GND11.TRG21.BS32. BS 23. BS 14. T NC5. M ic P S6.VDINE7.VDIN8.+5V1.RXD2.TXD3.+5V4.GND1. S HO RT2.MAGI3. X 14. X 25. T I6. T IE7.+15V8.GND9.NC10.NC11.NC12.NC1.HMCN T2.+15V3.GND1.+15V2.+12V3.G ND4.G ND5.-15V6.10V7.10VE8.+5V1.MCT2.MBK3. T IS TO P4.GND5.MPS6.MIE R1.TIY2.TIYE3.BP4.BPE5.BZ6.BZE1.+12V2.GND3.FAN_ERR11.HTER12.HVGA T E 13.TISTOP14.GND5.CN T6.+5V7.+15V8.STABY_REQ9.NC1.PW12.PW23.PW34.+24V5.GND1.PTI2.PTE3.LVR4.PMS5.GN D6.TXI7.TXE8.NC1. BP +2. BP -3.BZ +4.BZ -5.TRIG+6.TRIG-7.MTR+8.MTR-9. MT R E10.VD+11.VD-1.VD2.VDE3. MT R +4. MT R -J1118J1103J1104 J1111J1191J1110J1109TB101J8 J1106J1112 J1113IL-G-12PIL-8PIL -G -8P IL-G-11PB6P-SHFIL-G-9PMSTBA2.5/11-GIL- G -5PB3P-SHFIL-4PB8P-SHFIL -G -3 PMAGPOWER SUPPLY CIRCUITCBD-1682A1.+15V2.+12V3.+8V4.GND5.-15V6.10V7.10VE8.+5V1.MCT2.MBK3.HSP4.HTER5.TISTOP6.C27.GND8.MPS9.MIER2.1A1.2A2.1A1.2A2.1A1.2A1.MH2.NC3.MN1.MH2.NC3.MN1.X12.X2No.2No.1214356FILTERJ1004 J1003J 5J 4 J 3J1002J2102J2101J2103ANTTENA1. S HO R T2.MAG I3. X 14. X 25. T I6. T IE7.+15V8.GND9.NC10.NCB9P-SHF B8P-SHFB02P-NV(LF)(SN）350209-1IL-10P350209-2350209-1MODULATOR CIRCUITCPA-264MODULATOR UNIT INTERCONNECTIONCMB-406D.L①②③①②③GRNYELC2010.01UF 1KVC2020.22 U F 2 00 VR202 2.7KΩ1/2WC2030.22UF200VT201 R２01150Ω8WH-7LPRD0122CD202 CD201MD-12N1MD-12N1NJC3316Ａ101M1555Ｖ101R ECEIRVER UNIT INTERCONN ECTIONP3001 P3002P1109 P1110P1104P1103 P1003P1004P1111PULSE TRANS（W201)BLK.TP3P2103P1118DUMMYＡ102H-7ANRD0018(W001) (W002)(W003)(W006)P10021.+12V2.GND3.FAN_ERR2J1114IL-G-3P1.+12V2.C2J1105IL-G-2PP1105MODULATOR UNITNMA-551SCANNER INTERCONNECTIONCAX-13(W106)ZCRD1321※(W103)ZCRD1318※(W104)ZCRD 1319※(W105)ZCRD1320※ZCRD1267※J1IL-G-6PJ2IL-G-4PＡ301NJS6318ZCRD1268※CMA-902ZCRD1266※ZCRD1273※ZCRD1269※（W004）(W005)ZCRD1270※ZCRD1271※50/60ｋWP2101P21028.+5V9.NCRF CIRCUIT CAF-595J1001350428-11.M+2.M-1586514-21586514-2S.G.S.G. S.G.1.φZ2.φZE3.φ A4.φB5.+12V6.GNDJ13IL-6PSEYE LBLKBLUWHTREDSH I ELDB102ENCODER CHT-71AP13(W017)DISPLAY UNITFANREDBLUYELB104B103 FAN(W010)P1113 P1114(W301)TB102S101S-32F239568SAFETY SWITCHCSD-656(W203)ZCRD1274※REDWHTREDBLUYELZCRD1272※P1112J11121.PTI2.PTE1.LVR2.PMS3.E3.TXI4.TXEJ82J81PMP81P82WHTBLKBLUREDBLKWHTBRNNJU-847Z CRD1 27 9 ※(W018)ZCRD1275※(W008)ZCRD1283※S. G.S30kw, 2ﾕﾆｯﾄRED.TRED.TBLK.TBLK.TZCRD1322※(W302)ZCRD1453※S.G.CFR-229MAG FILTER CIRCUIT22 0pF ×5P1201+48V+48VGU1V1W1U1W1V1DISPLAY UNIT+48V+48VG12VU123434VUUTHUTHTH101TR101（200W）HEATER CONTROL PARTCHG-215(OPTION)WHT.TWHT.TW401 7ZCRD1509to CMC-1205R J1112WHTBLKBLUMOTOR DRIVERCBD-2000ZC RD 145 6※(W305)P1212BRAKE CIRCUITCFA-255J15011.V ERR2.EH-7EPRD0034B201J1505PC1501P1501B2P-VHP1505RELAY FILTER CIRCUITCSC-656PC1201IL-3P1.HMCNT2.+15V3.GNDP1211P12021.MU2J12121.VERR12.E3.MV2J1202J1201J12111.U13.V12.NC4.NC2.G N DB4P-VHB3P-NVIL-3PIL-2P1.VERR12.E1.VERR2.E1.P2.NC3.N1. P2. N1. BK H 13. BK H 21.BKS12.BKS21.+15V2.NC3.+15VEP1941 J1941J1903P1903J1905P1905J1912P1912BRAKE CONTROL CIRCUITCCB-655P1502J1921P1921J1911P19111.RE D3. BL KJ1511P1511IL-2PS3B-XH-A1-350210-0 1-350209-01-480700-0ZCRD1542※(W308)ZCRD1545※(W311) ZCRD1541※(W307)ZCRD1284※(W303)AC220VWC1ZCRD1543※(W309)ZCRD1544※(W310)BLAKE CIR CUI T BCFA-262BRAKE CIRCUIT ACFA-261R1R2R3R4R1120Ω30W330Ω30W×4×12.NC4.NC1. S 12.S23.S34. S 45.S56.S6J1502J15033.M21.M15.M3P1503MOTORMOTORB101CBP-205H-7BDRD00492.NC(W304)ZCRD1316※R1R21.2kΩ30WP15041.R 13.R2J1504B3P-VH2.NC3.M V 21.M U22.N C4.NC5.N C6.G N DB6P-VHto CCB-655 J1941(W308)ZCRD1542※

JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner UnitB－29BB.6.10 NKE-1139 (AC110V)Fig B-26: Interconnection Diagram of NKE-1139 (AC110V) NKE-1139PM (AC100V)空中線機内接続図SCANNER INTERCONNECTION CAX-14U1V1S101S-32239568RED.TBLK.T（W301) ZCRD1287※ RED WHTRED.TBLK.T（W302) ZCRD1288※SAFETY SWITCH CSD-657HEATER CONTROL PARTCHG-215(OPTION)TRANSCEIVER UNITWHT+12VC2ΦZEΦZΦAEΦBREDSHIELDYELBLUWHTSEB1 02ENCODER CHT-71A1C102C1012200p50V1000μ16V+BLKTB103BLKBLKAC100VUTHUVTH101TR101（100W）WHT.TTXITXEVERR1ELVRPMSETB104REDS.G.S.G.S.G.Sﾊﾞﾝﾄﾞ, 3ﾕﾆｯﾄ（W305) ZCRD1457※PTEPTIW401 7ZCRD1509WHT.TJ82J81 P81P82WHTBLKBLURE DBLKWHTBRN11PMNJU-84ZCRD1179※（W303) ZCRD1276※S.G.TRANSCEIVER UNIT TRANSCEIVER UNIT1.VERR12.E1.VERR2.E1.P2.NC3.N 1.BKH13.BKH21.BKS12.BKS21.+12V2.NC3.+12VEP1941 J1941J1903P1903J1905P1905J1912P1912BRAKE CONTROL CIRCUITCCB-655J1921P1921J1911P19111.RED3.BLKIL-2PB2PS-VHS3B-XH-A1-350210-0 1-350209-0ZCRD1553※ZCRD1552※(W307)ZCRD1543※(W309)ZCRD1544※(W310)CBD-2001(W304)ZCRD 1316※BRAKE CIRCUITCFA-255R1R21.2kΩ30W1.2kΩ30WP1504J15011.R13.R2H-7EPRD0035B201J1504J1505PC1501P1501B3P-VH2.NCB2P-VH1.P2.NP1502AC100VWC 1CBP-205H-7BDRD00492.NC4.NC1.S12.S23.S34.S45.S56.S6J1502J15033.M21.M15.M3P1503MOTORMOTO RB101(W308)MOTOR DRIVERBRA KE C IRCUIT BCFA-262BRAKE CIRCUIT ACFA-261R1R2R3R4R1120Ω30W330Ω30W×4×12.NC3.MV21.MU22.NC4.NC5.NC6.GNDB6P-VH1.VERR2.E

B－30JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner UnitB.6.11 NKE-1139 (AC220V)Fig B-27: Interconnection Diagram of NKE-1139 (AC220V) NKE-1139PM (AC220V)空中線機内接続図SCANNER INTERCONNECTION CAX-14U1V1S101S-32239568RED.TBLK.T（W301) ZCRD1287※ RED WHTRED.TBLK.T（W302) ZCRD1288※SAFETY SWITCH CSD-657HEATER CONTROL PARTCHG-215(OPTION)TRANSCEIVER UNITWHT+12VC2ΦZEΦZΦAEΦBREDSHIELDYELBLUWHTSEB1 02ENCODER CHT-71A1C102C1012200p50V1000μ16V+BLKTB103BLKBLKAC100VUTHUVTH101TR101（100W）WHT.TTXITXEVERR1ELVRPMSETB104REDS.G.S.G.S.G.Sﾊﾞﾝﾄﾞ, 3ﾕﾆｯﾄ（W305) ZCRD1457※PTEPTIW401 7ZCRD1509WHT.TJ82J81 P81P82WHTBLKBLURE DBLKWHTBRN11PMNJU-84ZCRD1179※（W303) ZCRD1276※S.G.TRANSCEIVER UNIT TRANSCEIVER UNIT1.VERR2.E1.VERR2.E1.P2.NC3.N 1.B K H 13.BKH21.BKS12.BKS21.+12V2.NC3.+12VEP1941 J1941J1903P1903J1905P1905J1912P1912BRAKE CONTROL CIRCUITCCB-655J1921P1921J1911P19111.RED3.BLKIL-2PB2PS-VHS3B-XH-A1-350210-0 1-350209-0ZCRD1553※ZCRD1552※(W307)ZCRD1543※(W309)ZCRD1544※(W310)CBD-2000(W304)ZCRD 1316※BRAKE CIRCUITCFA-255R1R21.2kΩ30W1.2kΩ30WP1504J15011.R13.R2H-7EPRD0034B201J1504J1505PC1501P1501B3P-VH2.NCB2P-VH1.P2.NP1502AC220VWC 1CBP-205H-7BDRD00492.NC4.NC1.S12.S23.S34.S45.S56.S6J1502J15033.M21.M15.M3P1503MOTORMOTO RB101(W308)MOTOR DRIVERBRA KE C IRCUIT BCFA-262BRAKE CIRCUIT ACFA-261R1R2R3R4R1120Ω30W330Ω30W×4×12.NC3.MV21.MU22.NC4.NC5.NC6.GNDB6P-VH1.VERR2.E

JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner UnitB－31BB.6.12 NTG-3230Fig B-28: Interconnection Diagram of NTG-3230 NTG-3230送受信機機内接続図1.TGT2.TGTE3.TNL4.-15V5.TNI6.+15V7.GND1.BS32.BS23.BS14.TNC5.MPS6.VDE7.VDRECEIVER UNIT NRG-229IF CIRCUIT CAE-499J101IL-9PJ102IL-7PT/R CONTROL CIRCUITCMC-1205R1.MONI2.GS3.GSE4.TGT5.TGTE6.TNL7.-15V8.TNI9.+15V10.GND11.TRG21.BS 32.BS 23.BS 14.TNC5.MicPS6.VDINE7.VDIN8.+5V1.RXD2.TXD3.+5V4.GND1.SHORT2.MAGI3.X14.X25.TI6.TIE7.+15V8.GND9.NC10.NC11.NC12.NC1.HMCNT2.+15V3.GND1.+15V2.+12V3.GND4.GND5.-15V6.10V7.10VE8.+5V1.MCT2.MBK3.TISTOP4.GND5.MPS6.MIER1.TIY2.TI YE3.BP4.B P E5.BZ6.B Z E1.+12V2.GND3.FAN_ERR11. HT E R12. HV GA T E13. T IS T O P14.GND5.CN T6.+5V7.+15V8. S T A BY _R E Q9.NC1.PW12.PW23.PW34.+24V5.GND1.PTI2.PTE3.LVR4.PMS5.GND6.TXI7.TXE8.NC1.BP+2.BP-3.BZ+4.BZ-5.TRIG+6.TRIG-7.MTR+8.MTR-9.MTRE10.VD+11.VD-1.VD2.VDE3.MTR+4.MTR-J1118J1103J1104 J1111J1191J1110J1109TB101J8 J1106J1112 J1113IL-G-12PIL-8PIL-G-8P IL-G -11PB6P-SHFIL -G -9PMSTBA2.5/11-GIL-G-5PB3P-SHFIL-4PB8P-SHFIL-G-3PMAGPOWER SUPPLY CIRCUITCBD-1682A1.+15V2.+12V3.+8V4.G ND5.-15V6.10V7.10VE8.+5V1.MCT2.MBK3.HSP4.HTER5 .TI ST OP6.C27.GND8.MPS9.MIER2.1A1.2A2.1A1.2A2.1A1.2A1.MH2.NC3.MN1.MH2.NC3.MN1.X12.X2No.2No.1214356FILTERJ1004 J1003J 5J 4 J 3J1002J2102J2101J2103ANTENNA1.SHORT2.MAGI3.X14.X25.TI6.TIE7.+15V8.G N D9.NC10.NCB9P-SHF B8P-SHFB02P-NV(LF)(SN）350209-1IL-10P350209-2350209-1MODULATOR CIRCUITCPA-264MODULATOR UNIT INTERCONNECTIONCMB-407TRHPL①③②①③GRNC2010.01UF 1KVC2020.22UF 200VR202 2.7KΩ1/2WC2030.22UF200VT1 R201150Ω8WH-7LPRD0122CD202 CD201MD-12N1MD-12N1NJC3317Ａ201M1555Ｖ101RECEIVER UNIT INTERCONNECTIONP3001 P3002P1109 P1110P1104P1103 P1003P1004P1111PUL S E TRANSW201BLK.TP3P2103P1118DUMMYＡ205(W001) (W002)(W003)(W006)P10021.+12V2.GND3.FAN_ERR2J1114IL-G-3P1.+12V2.C 2J1105IL-G-2PP1105MODULATOR UNITNMA-553P8TRANSCEIVER UNIT INTERCONNECTIONCMK-594(W106)(W103)(W104)(W105)ZCRD1218※ZCRD1227※ZCRD1229※P1201J1 IL-G-6PJ2 IL-G-4PPTIPTELVRPMSETXITXEEVERRVD+VD-TRIG+TRIG-BP+BP -/ BZ -BZ+MTREMTR-MTR+TB201 TB204(W301)ZCRD1215※ZCRD1228※(W302)ZCRD1216※Ａ203TL378AZCRD1219※ZCRD1230※CMA-902ZCRD1217※ZCRD1231※ZCRD1220※（W004）(W005)ZCRD1221※ZCRD1222※1.φZ2.φZE3.φA4.φB5.+12V6.GNDJ13IL-6PBLKREDBLKRED+12VC2φZEφZφAGNDφB+48VG+48V+48V+48VGRED.TWHT.TREDWHT(W008) ZCRD1224※SCANNER UNITSCANNER UNITDISPLAY UNITSCANNER UNITDISPLAY UNIT(W203) ZCRD1232※(W007) ZCRD1223※HC3L23L13L13L2TB203TB202P2101P2102P1018.+5V9.NCRF CIRCUIT CAF-595(W014)ZCRD1226※J1001350428-11.M+2.M-1586514-2(W013) ZCRD1225※1586514-2S.G.S.G. S . G.U1V1U0V0U1U0V1V0DISPLAY UNITH-7ANRD0018②(W303) ZCRD1484※RELAY FILTER CIRCUITCSC-656PC1201IL-3P1.H MCN T2.+15V3.G N DP1211P12021.MU2J12121.VERR2.E3.MV2J1202J1201J12111.U13.V12.N C4.N C2.GNDB4P-VHB3P-NVIL-3PIL-2PP1212S. G.CFR-229MAG FILTER CIRCUIT220pF×5YELS.G.H-7 ZCRD#### *:“#” means specif icatio n document No.“*” means revision of the sp ecfication document.

B－32JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection DiagramB.7 Terminal Board Connection Diagram

JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection DiagramB－33BB.7.1 JMA-9110-6XA/JMA-9110-6XAHFig B-29: Terminal Board Connection Diagram of JMA-9110-6XA/JMA-9110-6XAH 1VD+2VD-3TRIG+4TRIG-5BP+6BP-7BZ+8BZ-9MTR+10 MTR-11 MTRE12 (NC)13 +48 V14 +48 VGTB4101(ANT)1NA V1 TX+2NA V1 TX-3NA V1 RX+4NA V1 RX-5NA V2 TX+6NA V2 TX-7NA V2 RX+8NA V2 RX-9LO G RX +10 LO G RX -11 ALMTX+12 ALMTX-13 ALMRX+14 ALMRX-15 ARPAT X+16 ARPAT X-17 JAR PA TX+18 JAR PA TX-19 NSKT X+20 NSKT X-21 HDG RX+22 HDG RX-TB4501(OPTION) 1ARPAALM+2ARPAALM-3SYSALM+4SYSALM+5PWRALM+6PWRALM-7ARPAAC K+8ARPAAC K-9SYSACK+10 SYSACK-11 PWRACK+12 PWRACK-13 EXEVT+14 EXEVT-15 AISTX+16 AISTX-17 AIS_TG18 AISRX+19 AISRX-20 AIS_RG21 MNTTX+22 MNTTX-TB4601(ALARM) TB4401(EXT RADAR)1RBVD2RBVDE3ETIY34ETIY3E5SVD16SVD1E7ETIY18ETIY1E9EXφA110 EXφA1E11 EXφB112 EXφB1E13 EXφZ114 EXφZ1E1516171819202122232425 (NC)26 (NC)27 ACKOUT+28 ACKOUT-29 WMRST+30 WMRST-SVD2SVD2EETIY2ETIY2EEXφA2EXφA2EEXφB2EXφB2EEXφZ2EXφZ2E1(NC)2345P1+6P1-789S1+10 S2-1112TB4801(LOG)(NC)(NC)(NC)(NC)(NC)(NC)(NC) UWVFILTER ACIN1 U2 V3FGCBD-1684A TB5211 +2ー3FGCBD-1684A TB522CDC-1324J4409(DSUB-15P)RCQD-1891(JRC SUPPLY)GBHVREDGRNBLUGR YBLK11/R122/S133/S24S355/R26(NC)TB4701(GYRO)2A1AJ4J5J22A1AVDVDECOM+COM-2A1AJ3J1ETIYAGNDEXBPAGNDEXBZAGNDPTIPTETXITXELVRPMSEP82P81PTIPTETXITXELVRPMSEP2P1SCANNER UNITNKE-2103-6/6HSPERFORMANCEMONITORNJU-85DISPLAY UNIT NCD-4990BLU1YE LGRNWHT-B LUWHT-WH TORGBLKPNKBR N2REDPURWHT-YELWHT-WH TH-2695111153(JRC SUPPLY)1VDIN12VDIN1E3TRIGIN14TRIGIN1E5BPIN16BPIN1E7BZIN18BZIN1E9MTRIN1+10 MTRIN1-11 MTRIN1E12 PWRIN113 PWRIN1E14 PWROUT115 PWROUT1E16 VDOUT117 VDOUT1E18 TRIGOUT119 TRIGOUT1E20 BPOUT121 BPOUT1E22 BZOUT123 BZOUT1E24 MTROUT1+25 MTROUT1-26 MTROUT1ETB4201(ISW IN/OUT)RADAR(INTERSWITC H)WHTREDWH TBLKECDISH-2695110006(JRC SUPPLY)250V-TTYCS-1250V-TTYCS-1CONNINGDISPLAYVDR3C-2V x5 (MAX 30m)250V-TTYCS-1250V-TTYCS-1250V-TTYCS-1250V-TTYCS-1DGPSECHO SOUNDERLOG(NMEA0183)250V-TTYCS-4AIS0.6/1kV-DPYCYS-1.5250V-MPYCYS-7GYROLOG(200P /NM)0 . 6/ 1k V -D P YCY S- 1. 5ALARM MONITORINGSYSTEM(NEAREST APPROACH)YEL.T/PNK.TBLK.T/SKY.T ORN BLK GRN YEL WHTWHT.T/ O RN.TRED.T/GRN.TPUR.T/BRN.TBLU.T/GRY.TSHIP’S MAINSAC100-115V/AC220-240V 50/60Hz 1φW406 H-7ZCRD1342 A(Wiring is com pleted .)(X-BAND 10kW RADAR)JMA-9110-6XA/6XAH レーダー盤間接続図INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9110-6XA/6XAHWHTBLKWHTBRNBLUREDBLKWHTBRNBLUREDBLKBLK . T/SKY .TYE L .T/ PNK.TORNGR NBLKWH TYELPUR. T/ BRN.TR ED .T/ GR N. TWHT.T/ORN.TBLU .T /G RY .T19-CORES COMPOSITE CABLE (JRC SUPPLY)CFQ-6912-**CQD-2097 T ERMINAL BOARDWiring of PERFOR MAN CE MONITORis completed.0.6/1kV-DPYCY-6J4407RJ-45 LANUVWCBD-1661 ACOUT1BATT IN -BATT IN +SH IE L DCOAXIALCO A XI ALSHIELD

B－34JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection DiagramB.7.2 JMA-9110-6XA/JMA-9110-6XAH (desktop)Fig B-30: Terminal Board Connection Diagram of JMA-9110-6XA/JMA-9110-6XAH (desktop) 1VD+2VD-3TRIG+4TRIG-5BP+6BP-7BZ+8BZ-9MTR+10 MTR-11 MTRE12 (NC)13 +48 V14 +48 VGTB4101(ANT)1NA V1 TX+2NA V1 TX-3NA V1 RX+4NA V1 RX-5NA V2 TX+6NA V2 TX-7NA V2 RX+8NA V2 RX-9LO G RX +10 LO G RX -11 ALMTX+12 ALMTX-13 ALMRX+14 ALMRX-15 ARPAT X+16 ARPAT X-17 JAR PA TX+18 JAR PA TX-19 NSKT X+20 NSKT X-21 HDG RX+22 HDG RX-TB4501(OPTION) 1ARPAALM+2ARPAALM-3SYSALM+4SYSALM+5PWRALM+6PWRALM-7ARPAAC K+8ARPAAC K-9SYSACK+10 SYSACK-11 PWRACK+12 PWRACK-13 EXEVT+14 EXEVT-15 AISTX+16 AISTX-17 AIS_TG18 AISRX+19 AISRX-20 AIS_RG21 MNTTX+22 MNTTX-TB4601(ALARM) TB4401(EXT RADAR)1RBVD2RBVDE3ETIY34ETIY3E5SVD16SVD1E7ETIY18ETIY1E9EXφA110 EXφA1E11 EXφB112 EXφB1E13 EXφZ114 EXφZ1E1516171819202122232425 (NC)26 (NC)27 ACKOUT+28 ACKOUT-29 WMRST+30 WMRST-SVD2SVD2EETIY2ETIY2EEXφA2EXφA2EEXφB2EXφB2EEXφZ2EXφZ2E1(NC)2345P1+6P1-789S1+10 S2-1112TB4801(LOG)(NC)(NC)(NC)(NC)(NC)(NC)(NC) UWVFILTER ACIN1 +2ー3FGTB401CDC-1324J4409(DSUB-15P)RCQD-1891(JRC SUPPLY)GBHVREDGRNBLUGR YBLK11/R122/S133/S24S355/R26(NC)TB4701(GYRO)2A1AJ4J5J22A1AVDVDECOM+COM-2A1AJ3J1ETIYAGNDEXBPAGNDEXBZAGNDPTIPTETXITXELVRPMSEP82P81PTIPTETXITXELVRPMSEP2P1SCANNER UNITNKE-2103-6/6HSPERFORMANCEMONITORNJU-85DISPLAY UNIT NCD-4990TBLU1YE LGRNWHT-B LUWHT-WH TORGBLKPNKBR N2REDPURWHT-YELWHT-WH TH-2695111153(JRC SUPPLY)1VDIN12VDIN1E3TRIGIN14TRIGIN1E5BPIN16BPIN1E7BZIN18BZIN1E9MTRIN1+10 MTRIN1-11 MTRIN1E12 PWRIN113 PWRIN1E14 PWROUT115 PWROUT1E16 VDOUT117 VDOUT1E18 TRIGOUT119 TRIGOUT1E20 BPOUT121 BPOUT1E22 BZOUT123 BZOUT1E24 MTROUT1+25 MTROUT1-26 MTROUT1ETB4201(ISW IN/OUT)RADAR(INTERSWITC H)WHTREDWH TBLKECDISH-2695110006(JRC SUPPLY)250V-TTYCS-1250V-TTYCS-1CONNINGDISPLAYVDR3C-2V x5 (MAX 30m)250V-TTYCS-1250V-TTYCS-1250V-TTYCS-1250V-TTYCS-1DGPSECHO SOUNDERLOG(NMEA0183)250V-TTYCS-4AIS0.6/1kV-DPYCYS-1.5250V-MPYCYS-7GYROLOG(200P /NM)0.6/1kV-DPYCYS-1.5ALARM MONITORINGSYSTEM(NEAREST APPROACH)YEL.T/PNK.TBLK.T/SKY.T ORN BLK GRN YEL WHTWHT.T/ O RN.TRED.T/GRN.TPUR.T/BRN.TBLU.T/GRY.TSHIP’S MAINSAC100-115V/AC220-240V 50/60Hz 1φW407 H-7ZCRD1343 A(JRC SUPPLY)(X-BAND 10kW RADAR)JMA-9110-6XA/6XAH レーダー（卓上型）　盤間接続図INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9110-6XA/6XAH(desktop)WHTBLKWHTBRNBLUREDBLKWHTBRNBLUREDBLKBLK . T/SKY .TYE L .T/ PNK.TORNGR NBLKWH TYELPUR. T/ BRN.TR ED .T/ GR N. TWHT.T/ORN.TBLU .T /G RY .T19-CORES COMPOSITE CABLE (JRC SUPPLY)CFQ-6912-**CQD-2097 T ERMINAL BOARDWiring of PERFOR MAN CE MONITORis completed.1 U2 V3 WTB402W405 H-7ZC RD1341A(JRC SUPPLY)Wiring is completed.1 U2 V3FGCBD-1684A TB 521W408 H-7ZCRD1344 A(JRC SUPPLY)WHTBLKGRNGR NBLK- BL KWH T- B LK1 +2ー3FGCBD-1684A TB 522AC/DC CONVERTER UNITNBA-5135GRNBLKWHTGRNBLK-BLKWHT-BLKWHTBLKREDREDWHTBLK0.6/1kV-DPYCY-6J4407RJ-45 LANUVWCBD-1661 ACOUT1BATT IN -BATT IN +SH IE L DCOAXIALCO A XI ALSHIELD

JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection DiagramB－35BB.7.3 JMA-9122-6XAHFig B-31: Terminal Board Connection Diagram of JMA-9122-6XAH 1VD+2VD-3TRIG+4TRIG-5BP+6BP-7BZ+8BZ-9MTR+10 MTR-11 MTRE12 (NC)13 +48 V14 +48 VGTB4101(ANT)1NA V1 TX+2NA V1 TX-3NA V1 RX+4NA V1 RX-5NA V2 TX+6NA V2 TX-7NA V2 RX+8NA V2 RX-9LO G RX +10 LO G RX -11 ALMTX+12 ALMTX-13 ALMRX+14 ALMRX-15 ARPAT X+16 ARPAT X-17 JAR PA TX+18 JAR PA TX-19 NSKT X+20 NSKT X-21 HDG RX+22 HDG RX-TB4501(OPTION) 1ARPAALM+2ARPAALM-3SYSALM+4SYSALM+5PWRALM+6PWRALM-7ARPAAC K+8ARPAAC K-9SYSACK+10 SYSACK-11 PWRACK+12 PWRACK-13 EXEVT+14 EXEVT-15 AISTX+16 AISTX-17 AIS_TG18 AISRX+19 AISRX-20 AIS_RG21 MNTTX+22 MNTTX-TB4601(ALARM) TB4401(EXT RADAR)1RBVD2RBVDE3ETIY34ETIY3E5SVD16SVD1E7ETIY18ETIY1E9EXφA110 EXφA1E11 EXφB112 EXφB1E13 EXφZ114 EXφZ1E1516171819202122232425 (NC)26 (NC)27 ACKOUT+28 ACKOUT-29 WMRST+30 WMRST-SVD2SVD2EETIY2ETIY2EEXφA2EXφA2EEXφB2EXφB2EEXφZ2EXφZ2E1(NC)2345P1+6P1-789S1+10 S2-1112TB4801(LOG)(NC)(NC)(NC)(NC)(NC)(NC)(NC) UWVFILTER ACIN1 U2 V3FGCBD-1684A TB5211 +2ー3FGCBD-1684A TB522CDC-1324J4409(DSUB-15P)RCQD-1891(JRC SUPPLY)GBHVREDGRNBLUGR YBLK11/R122/S133/S24S355/R26(NC)TB4701(GYRO)2A1AJ4J5J22A1AVDVDECOM+COM-2A1AJ3J1TRIG+TRIG-BP+BP-BZ+BZ-PTIPTETXITXELVRPMSEP82P81PTIPTETXITXELVRPMSEP2P1SCANNER UNITNKE-2254-6HSPERFORMANCEMONITORNJU-85DISPLAY UNIT NCD-4990BLU1YE LGRNWHT-B LUWHT-WH TORGBLKPNKBR N2REDPURWHT-YELWHT-WH TH-2695111153(JRC SUPPLY)1VDIN12VDIN1E3TRIGIN14TRIGIN1E5BPIN16BPIN1E7BZIN18BZIN1E9MTRIN1+10 MTRIN1-11 MTRIN1E12 PWRIN113 PWRIN1E14 PWROUT115 PWROUT1E16 VDOUT117 VDOUT1E18 TRIGOUT119 TRIGOUT1E20 BPOUT121 BPOUT1E22 BZOUT123 BZOUT1E24 MTROUT1+25 MTROUT1-26 MTROUT1ETB4201(ISW IN/OUT)RADAR(INTERSWITC H)WHTREDWH TBLKECDISH-2695110006(JRC SUPPLY)250V-TTYCS-1250V-TTYCS-1CONNINGDISPLAYVDR3C-2V x5 (MAX 30m)250V-TTYCS-1250V-TTYCS-1250V-TTYCS-1250V-TTYCS-1DGPSECHO SOUNDERLOG(NMEA0183)250V-TTYCS-4AIS0.6/1kV-DPYCYS-1.5250V-MPYCYS-7GYROLOG(200P /NM)0.6/1kV-DPYCYS-1.5ALARM MONITORINGSYSTEM(NEAREST APPROACH)YEL.T/PNK.TBLK.T/SKY.T ORN BLK GRN YEL WHTWHT.T/ O RN.TRED.T/GRN.TPUR.T/BRN.TBLU.T/GRY.TSHIP’S MAINSAC100-115V/AC220-240V 50/60Hz 1φW406 H-7ZCRD1342 A(Wiring is com pleted .)(X-BAND 25kW RADAR)JMA-9122-6XAH レーダー盤間接続図INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9122-6XAHWHTBLKWHTBRNBLUREDBLKWHTBRNBLUREDBLKBLK . T/SKY .TYE L .T/ PNK.TORNGR NBLKWH TYELPUR. T/ BRN.TR ED .T/ GR N. TWHT.T/ORN.TBLU .T /G RY .T19-CORES COMPOSITE CABLE (JRC SUPPLY)CFQ-6912-**CQD-2097 T ERMINAL BOARD123UVUT HTB105CIRCUIT BREAKER5A (SHIP YARD SUPPLY)0.6/1kV-DPYCYS-1.5AC100V,1φ,100WNBL-175STEP-DOWN TRANSFORMER0.6/1kV-DPYCYS-1.50.6/1kV-DPYCYS-1.5SHIP’S MAINSAC220V, 1φ,for HEATER“D” HEATER OPTIONWiring of PERFOR MAN CE MONITORis completed.0.6/1kV-DPYCY-6J4407RJ-45 LANUVWCBD-1661 ACOUT1BATT IN -BATT IN +SH IE L DCOAXIALCO A XI ALSHIELD

B－36JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection DiagramB.7.4 JMA-9122-6XAH (desktop)Fig B-32: Terminal Board Connection Diagram of JMA-9122-6XAH (desktop) 1VD+2VD-3TRIG+4TRIG-5BP+6BP-7BZ+8BZ-9MTR+10 MTR-11 MTRE12 (NC)13 +48 V14 +48 VGTB4101(ANT)1NA V1 TX+2NA V1 TX-3NA V1 RX+4NA V1 RX-5NA V2 TX+6NA V2 TX-7NA V2 RX+8NA V2 RX-9LO G RX +10 LO G RX -11 ALMTX+12 ALMTX-13 ALMRX+14 ALMRX-15 ARPAT X+16 ARPAT X-17 JAR PA TX+18 JAR PA TX-19 NSKT X+20 NSKT X-21 HDG RX+22 HDG RX-TB4501(OPTION) 1ARPAALM+2ARPAALM-3SYSALM+4SYSALM+5PWRALM+6PWRALM-7ARPAAC K+8ARPAAC K-9SYSACK+10 SYSACK-11 PWRACK+12 PWRACK-13 EXEVT+14 EXEVT-15 AISTX+16 AISTX-17 AIS_TG18 AISRX+19 AISRX-20 AIS_RG21 MNTTX+22 MNTTX-TB4601(ALARM) TB4401(EXT RADAR)1RBVD2RBVDE3ETIY34ETIY3E5SVD16SVD1E7ETIY18ETIY1E9EXφA110 EXφA1E11 EXφB112 EXφB1E13 EXφZ114 EXφZ1E1516171819202122232425 (NC)26 (NC)27 ACKOUT+28 ACKOUT-29 WMRST+30 WMRST-SVD2SVD2EETIY2ETIY2EEXφA2EXφA2EEXφB2EXφB2EEXφZ2EXφZ2E1(NC)2345P1+6P1-789S1+10 S2-1112TB4801(LOG)(NC)(NC)(NC)(NC)(NC)(NC)(NC)1 +2ー3FGTB401CDC-1324J4409(DSUB-15P)RCQD-1891(JRC SUPPLY)GBHVREDGRNBLUGR YBLK11/R122/S133/S24S355/R26(NC)TB4701(GYRO)2A1AJ4J5J22A1AVDVDECOM+COM-2A1AJ3J1TRIG+TRIG-BP+BP-BZ+BZ-PTIPTETXITXELVRPMSEP82P81PTIPTETXITXELVRPMSEP2P1SCANNER UNITNKE-2254-6HSPERFORMANCEMONITORNJU-85DISPLAY UNIT NCD-4990TBLU1YE LGRNWHT-B LUWHT-WH TORGBLKPNKBR N2REDPURWHT-YELWHT-WH TH-2695111153(JRC SUPPLY)1VDIN12VDIN1E3TRIGIN14TRIGIN1E5BPIN16BPIN1E7BZIN18BZIN1E9MTRIN1+10 MTRIN1-11 MTRIN1E12 PWRIN113 PWRIN1E14 PWROUT115 PWROUT1E16 VDOUT117 VDOUT1E18 TRIGOUT119 TRIGOUT1E20 BPOUT121 BPOUT1E22 BZOUT123 BZOUT1E24 MTROUT1+25 MTROUT1-26 MTROUT1ETB4201(ISW IN/OUT)RADAR(INTERSWITC H)WHTREDWH TBLKECDISH-2695110006(JRC SUPPLY)250V-TTYCS-1250V-TTYCS-1CONNINGDISPLAYVDR3C-2V x5 (MAX 30m)250V-TTYCS-1250V-TTYCS-1250V-TTYCS-1250V-TTYCS-1DGPSECHO SOUNDERLOG(NMEA0183)250V-TTYCS-4AIS0.6/1kV-DPYCYS-1.5250V-MPYCYS-7GYROLOG(200P /NM)0.6/1kV-DPYCYS-1.5ALARM MONITORINGSYSTEM(NEAREST APPROACH)YEL.T/PNK.TBLK.T/SKY.T ORN BLK GRN YEL WHTWHT.T/ O RN.TRED.T/GRN.TPUR.T/BRN.TBLU.T/GRY.TSHIP’S MAINSAC100-115V/AC220-240V 50/60Hz 1φ(X-BAND 25kW RADAR)JMA-9122-6XAH レーダー（卓上型）　盤間接続図INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9122-6XAH(desktop)WHTBLKWHTBRNBLUREDBLKWHTBRNBLUREDBLKBLK . T/SKY .TYE L .T/ PNK.TORNGR NBLKWH TYELPUR. T/ BRN.TR ED .T/ GR N. TWHT.T/ORN.TBLU .T /G RY .T19-CORES COMPOSITE CABLE (JRC SUPPLY)CFQ-6912-**CQD-2097 T ERMINAL BOARD123UVUT HTB105CIRCUIT BREAKER5A (SHIP YARD SUPPLY)0.6/1kV-DPYCYS-1.5AC100V,1φ,100WNBL-175STEP-DOWN TRANSFORMER0.6/1kV-DPY CYS-1.50.6/1kV-DPYCYS-1.5SHIP’S MAINSAC220V, 1φ,for HEATER“D” HEATER OPTIONWiring of PERFOR MAN CE MONITORis completed.UWVFILTER ACIN1 U2 V3 WTB402W405 H-7ZC RD1341A(JRC SUPPLY)Wiring is completed.WHTBLKREDREDWHTBLKW407 H-7ZCRD1343 A(JRC SUPPLY)1 U2 V3FGCBD-1684A TB 521W 408 H-7ZC RD 134 4A( JRC SUPPL Y)WHTBLKGRNBLK- BL KWH T- B LK1 +2ー3FGCBD-1684A TB 522AC/DC CONVERTER UNITNBA-5135GRNBLKWHTGRNBLK-BLKWHT-BLKGR N0.6/1kV-DPYCY-6J4407RJ-45 LANUVWCBD-1661 ACOUT1BATT IN -BATT IN +SH IE L DCOAXIALCOAXIALSHIELD

JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection DiagramB－37BB.7.5 JMA-9122-6XA/9XAFig B-33: Terminal Board Connection Diagram of JMA-9122-6XA/9XA 1VD+2VD-3TRIG+4TRIG-5BP+6BP-7BZ+8BZ-9MTR+10 MTR-11 MTRE12 (NC)13 +48 V14 +48 VGTB4101(ANT)1NA V1 TX+2NA V1 TX-3NA V1 RX+4NA V1 RX-5NA V2 TX+6NA V2 TX-7NA V2 RX+8NA V2 RX-9LO G RX +10 LO G RX -11 ALMTX+12 ALMTX-13 ALMRX+14 ALMRX-15 ARPAT X+16 ARPAT X-17 JAR PA TX+18 JAR PA TX-19 NSKT X+20 NSKT X-21 HDG RX+22 HDG RX-TB4501(OPTION) 1ARPAALM+2ARPAALM-3SYSALM+4SYSALM+5PWRALM+6PWRALM-7ARPAAC K+8ARPAAC K-9SYSACK+10 SYSACK-11 PWRACK+12 PWRACK-13 EXEVT+14 EXEVT-15 AISTX+16 AISTX-17 AIS_TG18 AISRX+19 AISRX-20 AIS_RG21 MNTTX+22 MNTTX-TB4601(ALARM) TB4401(EXT RADAR)1RBVD2RBVDE3ETIY34ETIY3E5SVD16SVD1E7ETIY18ETIY1E9EXφA110 EXφA1E11 EXφB112 EXφB1E13 EXφZ114 EXφZ1E1516171819202122232425 (NC)26 (NC)27 ACKOUT+28 ACKOUT-29 WMRST+30 WMRST-SVD2SVD2EETIY2ETIY2EEXφA2EXφA2EEXφB2EXφB2EEXφZ2EXφZ2E1(NC)2345P1+6P1-789S1+10 S2-1112TB4801(LOG)(NC)(NC)(NC)(NC)(NC)(NC)(NC) UWVFILTER ACINCDC-1324J4409(DSUB-15P)RCQD-1891(JRC SUPPLY)GBHVREDGRNBLUGR YBLK11/R122/S133/S24S355/R26(NC)TB4701(GYRO)PTIPTETXITXELVRPMSEP82P81PTIPTETXITXELVRPMSEP2P1SCANNER UNITNKE-1125-61/62/91/92PERFORMANCEMONITORNJU-85DISPLAY UNIT NCD-4990BLU1YE LGRNWHT-B LUWHT-WH TORGBLKPNKBR N2REDPURWHT-YELWHT-WH TH-2695111153(JRC SUPPLY)1VDIN12VDIN1E3TRIGIN14TRIGIN1E5BPIN16BPIN1E7BZIN18BZIN1E9MTRIN1+10 MTRIN1-11 MTRIN1E12 PWRIN113 PWRIN1E14 PWROUT115 PWROUT1E16 VDOUT117 VDOUT1E18 TRIGOUT119 TRIGOUT1E20 BPOUT121 BPOUT1E22 BZOUT123 BZOUT1E24 MTROUT1+25 MTROUT1-26 MTROUT1ETB4201(ISW IN/OUT)RADAR(INTERSWITC H)WHTREDWH TBLKECDISH-2695110006(JRC SUPPLY)250V-TTYCS-1250V-TTYCS-1CONNINGDISPLAYVDR3C-2V x5 (MAX 30m)250V-TTYCS-1250V-TTYCS-1250V-TTYCS-1250V-TTYCS-1DGPSECHO SOUNDERLOG(NMEA0183)250V-TTYCS-4AIS0.6/1kV-DPYCYS-1.5250V-MPYCYS-7GYROLOG(200P /NM)0.6/1kV-DPYCYS-1.5ALARM MONITORINGSYSTEM(NEAREST APPROACH)REDBLU3ORN WHTSHIP’S MAINSAC100-115V/AC220-240V 50/60Hz 1φ(X-BAND 25kW RADAR)JMA-9122-6XA/9XA レーダー盤間接続図INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9122-6XA/9XAWHTBLKWHTBRNBLUREDBLKWHTBRNBLUREDBLK19-C ORES COMPOSITE CABLE (JRC SUPPLY)H-2695110056CQD-2097 T ERMINAL BOARD124YELGRN1VD+2VD-3TRIG+4TRIG-5BP+6BP-7BZ+8BZ-9MTR+10MTR-11MTRETB101 123V14W15+48V6+48VGU1TB102ORN WHT1243GRNYELBLURE D123UVUT HTB105CIRCUIT BREAKER5A (SHIP YARD SUPPLY)0.6/1kV-DPYCYS-1.5AC100V,1φ,100WNBL-175STEP-DOWN TRANSFORMER0.6/1kV-DPYC YS-1.50.6/1kV-DPYCYS-1.5SHIP’S MAINSAC220V, 1φ,for HEATER“D” HEATER OPTIONWiring of PERFOR MAN CE MONITORis completed.0.6/1kV-DPYCY-6J4407RJ-45 LANUVWCBD-1661 ACOUT1BATT IN -BATT IN +

B－38JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection DiagramB.7.6 JMA-9123-7XA/9XAFig B-34: Terminal Board Connection Diagram of JMA-9123-7XA/9XA 1VD+2VD-3TRIG+4TRIG-5BP+6BP-7BZ+8BZ-9MTR+10 MTR-11 MTRE12 (NC)13 +48 V14 +48 VGTB4101(ANT)1NA V1 TX+2NA V1 TX-3NA V1 RX+4NA V1 RX-5NA V2 TX+6NA V2 TX-7NA V2 RX+8NA V2 RX-9LO G RX +10 LO G RX -11 ALMTX+12 ALMTX-13 ALMRX+14 ALMRX-15 ARPAT X+16 ARPAT X-17 JAR PA TX+18 JAR PA TX-19 NSKT X+20 NSKT X-21 HDG RX+22 HDG RX-TB4501(OPTION) 1ARPAALM+2ARPAALM-3SYSALM+4SYSALM+5PWRALM+6PWRALM-7ARPAAC K+8ARPAAC K-9SYSACK+10 SYSACK-11 PWRACK+12 PWRACK-13 EXEVT+14 EXEVT-15 AISTX+16 AISTX-17 AIS_TG18 AISRX+19 AISRX-20 AIS_RG21 MNTTX+22 MNTTX-TB4601(ALARM) TB4401(EXT RADAR)1RBVD2RBVDE3ETIY34ETIY3E5SVD16SVD1E7ETIY18ETIY1E9EXφA110 EXφA1E11 EXφB112 EXφB1E13 EXφZ114 EXφZ1E1516171819202122232425 (NC)26 (NC)27 ACKOUT+28 ACKOUT-29 WMRST+30 WMRST-SVD2SVD2EETIY2ETIY2EEXφA2EXφA2EEXφB2EXφB2EEXφZ2EXφZ2E1(NC)2345P1+6P1-789S1+10 S2-1112TB4801(LOG)(NC)(NC)(NC)(NC)(NC)(NC)(NC) UWVFILTER ACINCDC-1324J4409(DSUB-15P)RCQD-1891(JRC SUPPLY)GBHVREDGRNBLUGR YBLK11/R122/S133/S24S355/R26(NC)TB4701(GYRO)PTIPTETXITXELVRPMSEP82P81PTIPTETXITXELVRPMSEP2P1SCANNER UNITNKE-1129-71/72/91/92PERFORMANCEMONITORNJU-85DISPLAY UNIT NCD-4990BLU1YE LGRNWHT-B LUWHT-WH TORGBLKPNKBR N2REDPURWHT-YELWHT-WH TH-2695111153(JRC SUPPLY)1VDIN12VDIN1E3TRIGIN14TRIGIN1E5BPIN16BPIN1E7BZIN18BZIN1E9MTRIN1+10 MTRIN1-11 MTRIN1E12 PWRIN113 PWRIN1E14 PWROUT115 PWROUT1E16 VDOUT117 VDOUT1E18 TRIGOUT119 TRIGOUT1E20 BPOUT121 BPOUT1E22 BZOUT123 BZOUT1E24 MTROUT1+25 MTROUT1-26 MTROUT1ETB4201(ISW IN/OUT)RADAR(INTERSWITC H)WHTREDWH TBLKECDISH-2695110006(JRC SUPPLY)250V-TTYCS-1250V-TTYCS-1CONNINGDISPLAYVDR3C-2V x5 (MAX 30m)250V-TTYCS-1250V-TTYCS-1250V-TTYCS-1250V-TTYCS-1DGPSECHO SOUNDERLOG(NMEA0183)250V-TTYCS-4AIS0.6/1kV-DPYCYS-1.5250V-MPYCYS-7GYROLOG(200P /NM)0.6/1kV-DPYCYS-1.5ALARM MONITORINGSYSTEM(NEAREST APPROACH)REDBLU3ORN WHTSHIP’S MAINSAC100-115V/AC220-240V 50/60Hz 1φ(X-BAND 25kW RADAR)JMA-9123-7XA/9XA レーダー盤間接続図INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9123-7XA/9XAWHTBLKWHTBRNBLUREDBLKWHTBRNBLUREDBLK19-C ORES COMPOSITE CABLE (JRC SUPPLY)H-2695110056CQD-2097 T ERMINAL BOARD124YELGRN123UVUT HTB105CIRCUIT BREAKER5A ( SHIP YA RD SU PPLY )0.6/1kV-DPYCYS-1.5AC100V,1φ,100WNBL -175STEP -DO WN TRA NSFO RME R0.6/1kV-DPYCYS-1.50.6/1kV -DPYCYS-1.5SHIP’S MAINSAC 220V , 1φ,for HEATER“D” HEATER OPTIONPTIPTELVRPMS(NC)ETB104TXITXE12345678E910 VER R1ΦB23C24ΦZE5U16V17W18+12v9ΦZ10ΦAETB103123V145U06V0U1TB2021GR NYELFR-9 FLEXIBLE WAVEGUIDE(JRC SUPPLY)19-CORES COMPOSITE CABLE (JRC SUPPLY)H-26951100561MTRE23BP+4BP-/BZ-5VD+6VD-7TRIG+8TRIG-9BZ+10MTR+MTR-TB201 123ΦA4E5+12V6C27ΦZE8ΦZ9ΦB10 +48V+48VGTB203 12345678910TB204PTIPTELVRPMS(NC)ETXITXEEVERR23GRNYE LREDBLU4ORNWHTORNWH T3124GRYREDBLUTRANSCEIVER UNIT NTG-32254GRYBLURED213WHTOR NYELGR NWiring of PERFOR MAN CE MONITORis completed.0.6/1kV-DPY CY-6PURBLKPURBLKJ4407RJ-45 LANUVWCBD-1661 ACOUT1BATT IN -BATT IN +

JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection DiagramB－39BB.7.7 JMA-9132-SAFig B-35: Terminal Board Connection Diagram of JMA-9132-SA 1VD+2VD-3TRIG+4TRIG-5BP+6BP-7BZ+8BZ-9MTR+10 MTR-11 MTRE12 (NC)13 +48 V14 +48 VGTB4101(ANT)1NA V1 TX+2NA V1 TX-3NA V1 RX+4NA V1 RX-5NA V2 TX+6NA V2 TX-7NA V2 RX+8NA V2 RX-9LO G RX +10 LO G RX -11 ALMTX+12 ALMTX-13 ALMRX+14 ALMRX-15 ARPAT X+16 ARPAT X-17 JAR PA TX+18 JAR PA TX-19 NSKT X+20 NSKT X-21 HDG RX+22 HDG RX-TB4501(OPTION) 1ARPAALM+2ARPAALM-3SYSALM+4SYSALM+5PWRALM+6PWRALM-7ARPAAC K+8ARPAAC K-9SYSACK+10 SYSACK-11 PWRACK+12 PWRACK-13 EXEVT+14 EXEVT-15 AISTX+16 AISTX-17 AIS_TG18 AISRX+19 AISRX-20 AIS_RG21 MNTTX+22 MNTTX-TB4601(ALARM) TB4401(EXT RADAR)1RBVD2RBVDE3ETIY34ETIY3E5SVD16SVD1E7ETIY18ETIY1E9EXφA110 EXφA1E11 EXφB112 EXφB1E13 EXφZ114 EXφZ1E1516171819202122232425 (NC)26 (NC)27 ACKOUT+28 ACKOUT-29 WMRST+30 WMRST-SVD2SVD2EETIY2ETIY2EEXφA2EXφA2EEXφB2EXφB2EEXφZ2EXφZ2E1(NC)2345P1+6P1-789S1+10 S2-1112TB4801(LOG)(NC)(NC)(NC)(NC)(NC)(NC)(NC) UWVFILTER ACINCDC-1324J4409(DSUB-15P)RCQD-1891(JRC SUPPLY)GBHVREDGRNBLUGR YBLK11/R122/S133/S24S355/R26(NC)TB4701(GYRO)PTIPTETXITXELVRPMSEP82P81PTIPTETXITXELVRPMSEP2P1SCANNER UNITNKE-1130-1/2PERFORMANCEMONITORNJU-84DISPLAY UNIT NCD-4990BLU1YE LGRNWHT-B LUWHT-WH TORGBLKPNKBR N2REDPURWHT-YELWHT-WH TH-2695111153(JRC SUPPLY)1VDIN12VDIN1E3TRIGIN14TRIGIN1E5BPIN16BPIN1E7BZIN18BZIN1E9MTRIN1+10 MTRIN1-11 MTRIN1E12 PWRIN113 PWRIN1E14 PWROUT115 PWROUT1E16 VDOUT117 VDOUT1E18 TRIGOUT119 TRIGOUT1E20 BPOUT121 BPOUT1E22 BZOUT123 BZOUT1E24 MTROUT1+25 MTROUT1-26 MTROUT1ETB4201(ISW IN/OUT)RADAR(INTERSWITC H)WHTREDWH TBLKECDISH-2695110006(JRC SUPPLY)250V-TTYCS-1250V-TTYCS-1CONNINGDISPLAYVDR3C-2V x5 (MAX 30m)250V-TTYCS-1250V-TTYCS-1250V-TTYCS-1250V-TTYCS-1DGPSECHO SOUNDERLOG(NMEA0183)250V-TTYCS-4AIS0.6/1kV-DPYCYS-1.5250V-MPYCYS-7GYROLOG(200P /NM)0.6/1kV-DPYCYS-1.5ALARM MONITORINGSYSTEM(NEAREST APPROACH)REDBLU3ORN WHT0.6/1kV-DPYCY-6SHIP’S MAINSAC100-115V/AC220-240V 50/60Hz 1φ(S-BAND 30kW RADAR)JMA-9132-SA レーダー盤間接続図INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9132-SAWHTBLKWHTBRNBLUREDBLKWHTBRNBLUREDBLK19-C ORES COMPOSITE CABLE (JRC SUPPLY)H-2695110056CQD-2097 T ERMINAL BOARD124YELGRN1VD+2VD-3TRIG+4TRIG-5BP+6BP-7BZ+8BZ-9MTR+10MTR-11MTRETB101 123V14W15+48V6+48VGU1TB102ORN WHT1243GRNYELBLURE DUT HCIRCUIT BREAKER5A (SHIP YARD SUPPLY)0.6/1kV -DPYCYS-1.5AC100V,1φ,100WNBL-175STEP-DOWN TRANSFORMER0.6/1kV-DPYCYS-1.50.6/1kV-DPYCYS-1.5SHIP’S MAINSAC220V, 1φ,for HEATER“D” HEATER OPTION78910Wiring of PERFOR MAN CE MONITORis completed.UV1112J4407RJ-45 LANUVWCBD-1661 ACOUT1BATT IN -BATT IN +

B－40JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection DiagramB.7.8 JMA-9133-SAFig B-36: Terminal Board Connection Diagram of JMA-9133-SA 1VD+2VD-3TRIG+4TRIG-5BP+6BP-7BZ+8BZ-9MTR+10 MTR-11 MTRE12 (NC)13 +48 V14 +48 VGTB4101(ANT)1NA V1 TX+2NA V1 TX-3NA V1 RX+4NA V1 RX-5NA V2 TX+6NA V2 TX-7NA V2 RX+8NA V2 RX-9LO G RX +10 LO G RX -11 ALMTX+12 ALMTX-13 ALMRX+14 ALMRX-15 ARPAT X+16 ARPAT X-17 JAR PA TX+18 JAR PA TX-19 NSKT X+20 NSKT X-21 HDG RX+22 HDG RX-TB4501(OPTION) 1ARPAALM+2ARPAALM-3SYSALM+4SYSALM+5PWRALM+6PWRALM-7ARPAAC K+8ARPAAC K-9SYSACK+10 SYSACK-11 PWRACK+12 PWRACK-13 EXEVT+14 EXEVT-15 AISTX+16 AISTX-17 AIS_TG18 AISRX+19 AISRX-20 AIS_RG21 MNTTX+22 MNTTX-TB4601(ALARM) TB4401(EXT RADAR)1RBVD2RBVDE3ETIY34ETIY3E5SVD16SVD1E7ETIY18ETIY1E9EXφA110 EXφA1E11 EXφB112 EXφB1E13 EXφZ114 EXφZ1E1516171819202122232425 (NC)26 (NC)27 ACKOUT+28 ACKOUT-29 WMRST+30 WMRST-SVD2SVD2EETIY2ETIY2EEXφA2EXφA2EEXφB2EXφB2EEXφZ2EXφZ2E1(NC)2345P1+6P1-789S1+10 S2-1112TB4801(LOG)(NC)(NC)(NC)(NC)(NC)(NC)(NC) UWVFILTER ACINCDC-1324J4409(DSUB-15P)RCQD-1891(JRC SUPPLY)GBHVREDGRNBLUGR YBLK11/R122/S133/S24S355/R26(NC)TB4701(GYRO)PTIPTETXITXELVRPMSEP82P81PTIPTETXITXELVRPMSEP2P1SCANNER UNITNKE-1139-1/2PERFORMANCEMONITORNJU-84DISPLAY UNIT NCD-4990BLU1YE LGRNWHT-B LUWHT-WH TORGBLKPNKBR N2REDPURWHT-YELWHT-WH TH-2695111153(JRC SUPPLY)1VDIN12VDIN1E3TRIGIN14TRIGIN1E5BPIN16BPIN1E7BZIN18BZIN1E9MTRIN1+10 MTRIN1-11 MTRIN1E12 PWRIN113 PWRIN1E14 PWROUT115 PWROUT1E16 VDOUT117 VDOUT1E18 TRIGOUT119 TRIGOUT1E20 BPOUT121 BPOUT1E22 BZOUT123 BZOUT1E24 MTROUT1+25 MTROUT1-26 MTROUT1ETB4201(ISW IN/OUT)RADAR(INTERSWITC H)WHTREDWH TBLKECDISH-2695110006(JRC SUPPLY)250V-TTYCS-1250V-TTYCS-1CONNINGDISPLAYVDR3C-2V x5 (MAX 30m)250V-TTYCS-1250V-TTYCS-1250V-TTYCS-1250V-TTYCS-1DGPSECHO SOUNDERLOG(NMEA0183)250V-TTYCS-4AIS0.6/1kV-DPYCYS-1.5250V-MPYCYS-7GYROLOG(200P /NM)0.6/1kV-DPYCYS-1.5ALARM MONITORINGSYSTEM(NEAREST APPROACH)REDBLU3ORN WHT0.6/1kV-DPYCY-6SHIP’S MAINSAC100-115V/AC220-240V 50/60Hz 1φ(S-BAND 30kW RADAR)JMA-9133-SA レーダー盤間接続図INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9133-SAWHTBLKWHTBRNBLUREDBLKWHTBRNBLUREDBLK14-C ORES COMPOSITE CABLE (JRC SUPPLY)H-2695110056CQD-2097 T ERMINAL BOARD124YELGRNCIRCUIT BREAKER5A ( SHIP YA RD SU PPLY )0.6/1kV-DPYCYS-1.5AC100V,1φ,100WNBL -175STEP -DO WN TRA NSFO RME R0.6/1kV-DPYCYS-1.50.6/1kV-DPYCYS-1.5SHIP’S MAINSAC 220V , 1φ,for HEATER“D” HEATER OPTIONPTIPTELVRPMS(NC)ETB104TXITXE123456789101ΦB23C24ΦZE5U16V17UTH8+12v9ΦZ10 ΦAETB103123V04W05U16V1W1U0TB2021GRNYE LHF-20D COAXIAL CABLE(JRC SUPPLY)19-CORES COMPOSITE CABLE (JRC SUPPLY)H-26951100561MTRE23BP+4BP-/BZ-5VD+6VD-7TRIG+8TRIG-9BZ+10MTR+MTR-TB201 123ΦA4E5+12V6C27ΦZE8ΦZ9ΦB10 +48V+48VGTB203 12345678910TB204PTIPTELVRPMS(NC)ETXITXEEVERR23GRNYE LREDBLU4ORNWHTORNWH T3124GRYBLUREDTRANSCEIVER UNIT NTG-32304GRYBLURED213WHTORNYE LGR NWiring of PERFOR MAN CE MONITORis completed.E1112 VER R(NC)(NC)UV1112PURBLKPURBLKJ4407RJ-45 LANUVWCBD-1661 ACOUT1BATT IN -BATT IN +

JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection DiagramB－41BB.7.9 NCD-4990TFig B-37: Inter-Unit Connection Diagram of NCD-4990T DISPLAY UNIT NCD-4990TMONITOR UNITNWZ-170OPERATION UNITNCE-5163SUB OPERATION UNITNCE-51631 U2 V3FGCBD-1684A TB5211 +2ー3FGCBD-1684A TB522RADAR PROCESS UNITNDC-1399-9AC/DC CONVERTER UNITNBA-5135Option for X-band 10kW and X-band 25kW-HS.Used with NKE-2103-6,NKE-2103-6HS and NKE-2254-6HS1 +2ー3FGTB4021 U2 V3 WCBD-1661 AC OUT 1J4311J4312CBD-1661AC OUT 2OptionMainSubJ4406 DVI-D J4309DSUB -9PFEMALERADAR PROCESSCIRCUITCDC-1324TERMINAL BOARDCQD-2097POWER SUPPLYCBD-1661NCD-4990T 卓上型レーダー指示機ユニット間接続図INTERCONNECTION DIAGRAM OF DISPLAY UNIT TYPE NCD-4990T(desktop)JMA-9100 Series RADAR

B－42JMA-9100 Instruction Manual > B.DRAWINGS > B.8 GYRO I/FB.8 GYRO I/FFig B-38: Parts Location of CMJ-462ETableB-1： Setting Table of CMJ-462E S1/S2GYRO INPUT SIGNALINDICATOR LEDジャイロ入力信号LEDGYRO SIGNAL PROCESSINDICATOR LEDジャイロ信号処理表示LEDLOG PULSE INDICATOR LEDログパルス表示LEDERROR INDICATOR LEDエラー表示LEDGYRO LOW-VOLTAGEALERT LEDジャイロ低電圧警告LEDSERIAL SIGNAL INDICATOR LEDシリアル信号表示LEDOPENプラグ無しKEEP DEFAULT設定不要LOW-VOLTAGE GYRO SETTINGジャイロ低電圧時に設定S1 SETTING 1 2 3 4 5 6 7 8 S2 SETTING 1 2 3 4 5 6 7 8 STEP ON ONSYNC OFF BSHLOG ALM OFF 36X ON ON ON 90X OFF ON GYRO SIMULATOR OFF 180X ON OFF ONRATIO 360X OFF OFF LOG SIMULATOR OFF 逆／REV ON N.C. (No Connection) OFF ジャイロ信号 GYRO SETTING 回転方向 DIRECTION 正／NOR OFF 5 SEC ON シンクロ／SYNC ON GYRO ALM TIME 0.2 SEC OFF パルス／PULSE OFF HDT ( NMEA (HDT/THS) ) ON 未接続／NC OFF GYRO SRC (Heading Sensor Source) GYRO OFF 100P／30X ON ON 4800 BPS OFF OFF 200P／90X OFF ON 9600 BPS ON OFF 400P／180X ON OFF 19200 BPS OFF ON ログ信号 LOG SETTING パルス PULSE/NM 800P／360X OFF OFF NMEA BAUDRATE 38400 BPS ON ON

JMA-9100 Instruction Manual > B.DRAWINGS > B.8 GYRO I/FB－43BTableB-2： Gyro, Log Settings

B－44JMA-9100 Instruction Manual > B.DRAWINGS > B.9 Inter Switch UnitB.9 Inter Switch UnitB.9.1 Terminal Board Connection DiagramFig B-39: Terminal Board Connetion Diagram of NQE-3141-2AVDIN 1VDIN 1ETRIGIN 1TRIGIN 1EBPIN 1BPIN 1EBZIN 1MTRIN 1+MTRIN 1-BZIN 1EMTRIN 1EPWRIN 1+PWRIN 1EPWROUT 1PWROUT 1EVDOUT 1VDOUT 1ETRIGOUT 1TRIGOUT 1EBPOUT 1BPOUT 1EBZOUT 1EMTROUT 1+BZOUT 1MTROUT 1 -MTORUT 1E1234567891011121314151617181920212223242526VDIN 1VDIN 1ETRIGIN 1TRIGIN 1EBPIN 1BPIN 1EBZIN 1MTRIN 1+MTRIN 1-BZIN 1EMTRIN 1EPWRIN 1+PWRIN 1EPWROUT 1PWROUT 1EVDOUT 1VDOUT 1ETRIGOUT 1TRIGOUT 1EBPOUT 1BPOUT 1EBZOUT 1EMTROUT 1+BZOUT 1MTROUT 1-MTORUT 1E1234567891011121314151617181920212223242526TB4201ISW IN/OUT TB4201ISW IN/OUTDISPLAY 1 DISPLAY 212BLUEYELLOWGREENWHITE-BLUEWHITE-WHITEORANGEBLACKPINKBROWNREDPURPLECLEARWHITE-YELLOWWHITE-WHITENCD-4990 NCD-4990H-2695111153(JRC SUPPLY)

JMA-9100 Instruction Manual > B.DRAWINGS > B.9 Inter Switch UnitB－45BFig B-40: Terminal Board Connection Diagram of NQE-3141-4ACH-1TB911 TB912DISPLAY1NCD-4990TB42011234567891011121314151234567891011DISPLAY2NCD-4990TB4201VDIN 1VDIN 1ETRIGIN 1TRIGIN 1EBPIN 1BPIN 1EBZIN 1MTRIN 1+MTRIN 1-BZIN 1EMTRIN 1EPWRIN 1+PWRIN 1EPWROUT 1PWROUT 1EVDOUT 1VDOUT 1ETRIGOUT 1TRIGOU T 1EBPOUT 1BPOUT 1EBZOUT 1EMTROUT 1+BZOUT 1MTROUT 1-MTORUT 1E1234567891011121314151617181920212223242526DISPLAY3NCD-4990TB4201CH-2TB913 TB9141234567891011121314151234567891011CH-3TB915 TB9161234567891011121314151234567891011NKE-3141-4CCL-304RVDIN 1VDIN 1ETRIG IN 1TRIGIN 1EBPIN 1BPIN 1EBZIN 1MTRIN 1+MTRIN 1-BZIN 1EMTRIN 1EPWRIN 1+PWRIN 1EPWROUT 1PWROUT 1EVDOUT 1VDOUT 1ETRIGOUT 1TRIGOUT 1EBPOUT 1BPOUT 1EBZOUT 1EMTROUT 1+BZOUT 1MTROUT 1-MTORUT 1E1234567891011121314151617181920212223242526VDIN 1VDIN 1ETRIGIN 1TRIG IN 1EBPIN 1BPIN 1EBZIN 1MTRIN 1+MTRIN 1-BZIN 1EMTRIN 1EPWRIN 1+PWRIN 1EPWROUT 1PWROUT 1EVDOUT 1VDOUT 1ETRIGOUT 1TRIGOUT 1EBPOUT 1BPOUT 1EBZOUT 1EMTROUT 1+BZOUT 1MTROUT 1-MTORUT 1E123456789101112131415161718192021222324252612BLUYELGRNWHT-BLUWHT-WHTORGBLKPNKBRNREDPURCLRWHT-YELWHT-WHT12BLUYELGRNORGBLKPNKBRNREDPUR12BLUYELGRNORGBLKPNKBRNREDPUR2REDPURWHT1BLUYELGR NORGBLKPNKBRN2REDPURWHT1BLUYELGRNORGBLKPNKBRN2REDPURCLRWHT-YELWHT-W HT1BLUYELGRNWHT-BLUWHT-WHTORGBLKPNKBRNH-2695111153 (JRC SUPPLY )H-2695111153 (JRC SUPPLY )H-2695111153 (JRC SUPPLY )VDIN 1VDIN 1ETRIGIN 1TRIGIN 1EBPIN 1BPIN 1EBZIN 1MTRIN 1+MTRIN 1-BZIN 1EMTRIN 1EPWRIN 1+PWRIN 1EPWROUT 1PWROUT 1EVDOUT 1VDOUT 1ETRIGOUT 1TRIGOUT 1EBPOUT 1BPOUT 1EBZOUT 1EMTROUT 1+BZOUT 1MTROUT 1-MTORUT 1E1234567891011121314151617181920212223242526DISPLAY4NCD-4990TB4201CH-4TB915 TB916123456789101112131415123456789101112BLUYELGRNORGBLKPNKBRNREDPUR2REDPURWHT1BLUYELGR NOR GBLKPNKBRNH-2695111153 (JRC SUPPLY )WHT-YELWHT-WHTWHT-BLUWHT-WHT WHT-YELWHT-WHTWHT-BLUWHT-WHTWHT-YELWHT-WHTWHT-BLUWHT-WHTWHT-BLUWHT-WHTCLRWHT-YELWHT-WHTWHT-BLUWHT-WHTCLRWHT-YELWHT-WHTWHT-BLUWHT-WHTCLRWHT-YELWHT-WHT

B－46JMA-9100 Instruction Manual > B.DRAWINGS > B.9 Inter Switch UnitB.9.2 Interconnection DiagramFig B-41: Interconnection Diagram of NQE-3141-2ATerminal boardJ4308 ISWJ903123456-15VGNDGNDGND5 V+15VP903123456-15VGNDGNDGND5 V+15V1212VIN+VIN-ＴＢ912ＴＢ914ＴＢ916ＴＢ918ＴＢ911ＴＢ913ＴＢ915ＴＢ917CH-4CH-3CH-2CH-1J3 J3112626CCL-304P902J2J1CBD-1675H-7ZCRD0971H-7ZCRD0972126126CQD-1973 CQD-1973H-7ZCRD0970AH-7ZCRD0970ATerminal boardJ4306(ISW-1CH)Terminal boardJ4307(ISW-1CH)

JMA-9100 Instruction Manual > B.DRAWINGS > B.9 Inter Switch UnitB－47BFig B-42: Interconnection Diagram of NQE-3141-4A11.MTROUTE10.MTROUT-9.MTROUT+8.BZOUTE7.BZOUT5.BPOUT6.BPOUTE2.VDOUTE3.TRGOUT4.TRGOUTE1.VDOUT15 . PW R OU TE14 . PW R OU T13 . RW R IN E12 . PW R IN11 . M T R I NE9. M T R IN +10 . M T R I N-6.B PIN E7. B Z IN8. B Z IN E5.B PIN4.T R G INE3.T R G IN2.V DI NE1.V DI NCH-1TB 911 TB 912 TB 913 TB 914 TB 915 TB 916 TB 917 TB 91812CCL-304TODISPLAY1NCD-4990TB4201TODISPLAY2NCD-4990TB4201TODISPLAY3NCD-4990TB4201CH -2 CH-3 CH-43J90312345612345678910J904J90512J909-15VGNDGNDGND5 V+15VAC(L)AC(N)TRTP+EPO WL EDTRTP-FANVFANEFANP LS123456-15VGNDGNDGND5 V+15VP903P902135AC(L )AC(N)FGSP904P905P909CN2CN1P901LOADBCDALINE1234UVETB901AC100V-240VTE901FGCD901R901H-7ZCRD0920H-7ZCRD0921H-7ZCRD0919CBA-357B901CB901C901 C902 C903LF901

B－48JMA-9100 Instruction Manual > B.DRAWINGS > B.9 Inter Switch Unit

Menu IndexC.1 Main .......................................................................................................C-1C.2 PI ............................................................................................................C-5C.3 TT ...........................................................................................................C-7C.4 AIS .........................................................................................................C-8C.5 AZ ..........................................................................................................C-9C.6 Track ....................................................................................................C-10C.7 Route ...................................................................................................C-11C.8 U.Map ..................................................................................................C-12C.9 Serviceman Menu ...............................................................................C-14Appendix CMenu Index

JMA-9100 Instruction Manual > C.Menu Index > C.1 MainC－1CC.1 Main├1. EBL Maneuver Setting- - - - - - - - - - - - - - - - - - - - - - - - - section 4.1.5 on page 4-14│├1. EBL Maneuver│├2. Reach│├3. Turn Mode│└4. Turn Set├2. File Manager - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.11.1 on page 3-120├3. RADAR Menu│├1. Process Setting - - - - - - - - - - - - - - - - - - - - - - - - section 3.8.1 on page 3-91││├1. Video Latitude - - - - - - - - - - - - - - - - - - - - section 3.8.1.1 on page 3-91││├2. Video Noise Rejection - - - - - - - - - - - - - - - - section 3.8.1.2 on page 3-92││├3. AUTO Dynamic Range - - - - - - - - - - - - - - - section 3.8.1.3 on page 3-92││├4. Process Switch - - - - - - - - - - - - - - - - - - - section 3.8.1.4 on page 3-93││├5. 2nd Process Mode- - - - - - - - - - - - - - - - - - section 3.8.1.5 on page 3-93││├6. Process Switch Rrange - - - - - - - - - - - - - - - section 3.8.1.6 on page 3-93││├7. Fast Target Detection - - - - - - - - - - - - - - - - section 3.8.1.7 on page 3-94││├8. User Function Setting - - - - - - - - - - - - - - - - -section 3.9.3 on page 3-113│││├1. Function1 Setting││││├1. Mode - - - - - - - - - - - - - - - - - - - - - - - - page 3-113││││├2. IR││││├3. Process││││├4. Target Enhance││││├5. AUTO Sea/Rain││││├6. Save Present State││││├9. Next││││├1. Pulse Length 0.75nm - - - - - - - - - - - - - - - - page 3-115││││├2. Pulse Length 1.5nm││││├3. Pulse Length 3/4nm││││├4. Pulse Length 6/8nm││││├5. Pulse Length 12nm││││├6. Pulse Length 16nm││││├9. Next││││├1. Video Latitude - - - - - - - - - - - - - - - - - - - - page 3-115││││├2. Video Noise Rejection││││├3. AUTO Dynamic Range││││├4. Process Switch││││├5. 2nd Process Mode││││├6. Process Switch Range││││├7. Fast Target Detection││││├9. Next││││├1. Trails Interval - - - - - - - - - - - - - - - - - - - - page 3-115││││├2. Trails Mode││││├3. Trails Reference Level││││├4. Trails Reduction││││├6. Trails Process││││├7. Max Interval││││├9. Next││││├1. Gain Offset - - - - - - - - - - - - - - - - - - - - - page 3-115││││├2. PRF││││├3. Small Buoy Detection││││├4. Fishnet Detection││││├5. Antenna Height││││├8. Set Mode Default││││└9. Initialize│││├2. Function2 Setting│││├3. Function3 Setting│││└4. Function4 Setting││└9. SART - - - - - - - - - - - - - - - - - - - - - - - - - - section 6.5 on page 6-12│├2. RADAR Trails Setting││├1. Trails Mode - - - - - - - - - - - - - - - - - - - - - section 3.8.2.1 on page 3-95││├2. Trails Ref Level - - - - - - - - - - - - - - - - - - - section 3.8.2.2 on page 3-95││├3. Trails Reduction - - - - - - - - - - - - - - - - - - - section 3.8.2.3 on page 3-96││├5. Trails Process - - - - - - - - - - - - - - - - - - - - section 3.8.2.4 on page 3-96

C－2JMA-9100 Instruction Manual > C.Menu Index > C.1 Main││└6. Max Interval - - - - - - - - - - - - - - - - - - - - - section 3.8.2.5 on page 3-96│└3. TXRX Setting││├1. PRF Fine Tuning - - - - - - - - - - - - - - - - - - section 3.8.3.1 on page 3-97││├2. Stagger Trigger - - - - - - - - - - - - - - - - - - - section 3.8.3.2 on page 3-97││├4. PRF - - - - - - - - - - - - - - - - - - - - - - - - - section 3.8.3.3 on page 3-97││└5. Ice Class Standby Mode - - - - - - - - - - - - - - - section 3.8.3.4 on page 3-98├4. Multi Window Setting│├1. DIR/DIST EXP Display- - - - - - - - - - - - - - - - - - - - section 3.8.8.1 on page 3-105│├2. Numeric NAV INFO - - - - - - - - - - - - - - - - - - - - - section 3.8.8.2 on page 3-105│├3. Depth Graph Setting- - - - - - - - - - - - - - - - - - - - - section 3.8.8.3 on page 3-106││├1. Depth Graph Display││├2. Depth Range││├3. Time Range││└4. Depth Unit│├4. Wind Graph Setting - - - - - - - - - - - - - - - - - - - - - section 3.8.8.4 on page 3-107││├1. Wind Graph Display││└2. Wind Speed Unit│├5. TEMP Graph Setting- - - - - - - - - - - - - - - - - - - - - section 3.8.8.5 on page 3-108││├1. TEMP Graph Display││├2. TEMP Graph Color││├3. TEMP Range│││├1. Temperature setting (MIN)│││├2. Temperature setting │││├3. Temperature setting │││├4. Temperature setting │││├5. Temperature setting │││└6. Temperature setting (MAX)││└4. Time Range│└6. Course Bar Setting - - - - - - - - - - - - - - - - - - - - - section 3.8.8.6 on page 3-109││├1. Course Bar Display││├2. Autopilot Course││└3. ROT Scale├5. Map Setting│├3. JRC/ERC Setting││├1. Day/Night││├2. Color of Land││├3. Bright of Land││├4. Color of Sea││├5. Bright of Sea││├6. Color of Name││├7. Bright of Name││├8. Bright of Track/Mark/Line││├9. Next││├1. LAT/LON Line││├2. Color of L/L Line││└3. Bright of L/L Line│├5. Map Display Setting││└3. LAT/LON Correction│└7. Map Draw AZI Mode├6. NAV Equipment Setting│├1. GYRO Setting - - - - - - - - - - - - - section 3.4.14 on page 3-36, section 7.1.7 on page 7-9│├2. MAG Compass Setting - - - - - - - - - - - - - - - - - - - -section 3.4.16 on page 3-37││├1. Heading Correction││└2. Correct Value│└3. Set/Drift Setting - - - - - - - - - - - - - - - - - - - - - - - section 3.4.16.1 on page 3-38││├1. Correction││├2. Set││└3. Drift├7. Sub Menu│├1. Display Color Setting - - - - - - - - - - - - - - - - - - - - section 3.8.5.1 on page 3-99││├1. Day/Night - - - - - - - - - - - - - - - - - - - - - - section 3.8.5.2 on page 3-100││├2. Outer PPI││├3. Inner PPI││├4. Character││├5. RADAR Video││├6. RADAR Trails(Time)││├8. Target Symbol││├9. Next││├1. Cursor││├2. Range Rings

JMA-9100 Instruction Manual > C.Menu Index > C.1 MainC－3C││├3. EBL/VRM/PI││└4. Own Symbol/HL/Vector│├2. Brilliance Setting- - - - - - - - - - - - - - - - - - - - - - - section 3.8.5.3 on page 3-100││├1. RADAR Video - - - - - - - - - - - - - - - - - - - - section 3.8.5.4 on page 3-101││├2. RADAR Trails││├3. Target Symbol- - - - - - - - - - - - - - - - - - - - section 3.8.5.5 on page 3-102││├4. Range Rings││├5. EBL/VRM/PI││├6. Character││├7. Own Symbol/HL/Vector││└8. Keyboard│├3. User Setting││├1. Load User Setting - - - - - - - - - - - - - - - - - - section 3.10.1 on page 3-118││├2. Save User Setting - - - - - - - - - - - - - - - - - - section 3.10.2 on page 3-119││└3. Delete User Setting - - - - - - - - - - - - - - - - - section 3.10.3 on page 3-119│├4. Option Key Setting││├1. Option1 - - - - - - - - - - - - - - - - - - - - - - - -section 3.8.7 on page 3-103││└2. Option2 - - - - - - - - - - - - - - - - - - - - - - - -section 3.8.7 on page 3-103│├5. Buzzer Volume - - - - - - - - - - - - - - - - - - - - - - - -section 3.8.6 on page 3-102││├1. Key ACK││├2. OPE Miss││├3. CPA/TCPA Alarm││├4. New Target Alarm││├5. Lost Alarm││├6. Navigation Alarm││├7. System Alarm││└8. Inter Switch│├6. Date/Time Setting - - - - - - - - - - - - - - - - - - - - - - - section 7.2.7 on page 7-20││├1. UTC/LMT││├2. LMT Date││├3. LMT Time││├4. Time Zone││├5. Display Style││└6. Synchronize with GPS│├7. Screen Capture Setting││├1. Select Item│││├1. Graphic│││├2. RADAR Video│││├3. RADAR Trails│││└4. Map││├2. Select Card Slot││├3. File Erase││├4. AUTO Capture Interval││└5. AUTO File Erase│├9. EBL/Cursor Setting - - - - - - - - - - - - - - - - - - - - - - - section 4.1.3 on page 4-3││├1. EBL1 Bearing Fix││├2. EBL2 Bearing Fix││└3. Cursor Setting - - - - - - - - - - - - - - - - - - - - - section 4.1.3.3 on page 4-5│││├1. EBL/VRM Control CURS│││├2. Cursor Length│││└4. Cursor Pattern├8. Plot Setting│└6. AUTO Backup - - - - - - - - - - - - - - - - - - - - - - - - - section 3.8.9 on page 3-110├9. Test Menu- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 8.3.1 on page 8-6│├1. Self Test - - - - - - - - - - - - - - - - - - - - - - - - - - - section 8.3.1.1 on page 8-7││├1. Memory Test│││├1. SDRAM│││├2. SRAM│││├3. FLASH ROM│││└4. GRAPHIC││├2. TXRX Test││├3. Line Test││└4. Supply Voltage│├2. Monitor Test- - - - - - - - - - - - - - - - - - - - - - - - - - section 8.3.1.2 on page 8-9││├1. Pattern 1││├2. Pattern 2││├3. Pattern 3││├4. Pattern 4││├5. Pattern 5││├6. Pattern 6

C－4JMA-9100 Instruction Manual > C.Menu Index > C.1 Main││├7. Pattern 7││└8. Pattern 8│├3. Keyboard Test- - - - - - - - - - - - - - - - - - - - - - - - - section 8.3.1.3 on page 8-9││├1. Key Test││├2. Buzzer Test││└3. Light Test│├4. MON Display - - - - - - - - - - - - - - - - - - - - - - - - section 8.3.1.4 on page 8-10│├5. System Alarm Log - - - - - - - - - - - - - - - - - - - - - - section 8.3.1.5 on page 8-10│└6. System Information - - - - - - - - - - - - - - - - - - - - - section 8.3.1.6 on page 8-11└0. EXIT

JMA-9100 Instruction Manual > C.Menu Index > C.2 PIC－5CC.2 PI├1. Display for All Lines - - - - - - - - - - - - - - - - - - - - - - - - - - section 4.1.4.3 on page 4-9├2. Operation Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-10│├All│├Individual│├Track│└Equiangular├3. Control1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-11│├All:All2│├Individual:Sequential│├Individual:Index Line 1│├Individual:Index Line 2│├Individual:Index Line 3│├Individual:Index Line 4│├Individual:Index Line 5│├Individual:Index Line 6│├Individual:Index Line 7│├Individual:Index Line 8│├Track:Group 1│├Track:Group 2│├Track:Group 3│├Track:Group 4│├Equiangular:Group 1│├Equiangular:Group 2│├Equiangular:Group 3│└Equiangular:Group 4├4. Floating - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -page 4-11├5. Heading Link - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -page 4-11├6. Next├8. Press EBL Dial to Control PI#3├9. Press VRM Dial to Move End Point#ii├1. Range Scale Link - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-12├2. Reference Bearingi- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-12│├All:True4│├All:HL│├Individual:True│├Individual:HL│├Individual:Index Line 1│├Individual:Index Line 2│├Individual:Index Line 3│├Individual:Index Line 4│├Individual:Index Line 5│├Individual:Index Line 6│├Individual:Index Line 7│├Individual:Index Line 8│├Track:True│├Track:HL│├Track:Index Line 1│├Track:Index Line 2│├Track:Index Line 3│├Track:Index Line 4│├Track:Index Line 5│├Track:Index Line 6│├Track:Index Line 7│└Track:Index Line 8├3. Operation Area - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-13├4. Display for Individual Line - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-131.The setting items are determined by the setting of Operation Mode.2.Operating Mode : Control3.Displayed only when "3. Control" is Individual.4.Operating Mode : Reference Bearing

C－6JMA-9100 Instruction Manual > C.Menu Index > C.2 PI│├1. Index Line 1│├2. Index Line 2│├3. Index Line 3│├4. Index Line 4│├5. Index Line 5│├6. Index Line 6│├7. Index Line 7│└8. Index Line 8├8. Press EBL Dial to Control PI#ii└9. Press VRM Dial to Move End Point#ii

JMA-9100 Instruction Manual > C.Menu Index > C.3 TTC－7CC.3 TT├1. Association Setting - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.4 on page 5-37│├1. Association│├2. Proprity│├3. Bearing│├4. Range│├5. Course│├6. Speed│└7. Applicable AIS Target├2. Target Track Setting - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.6.2 on page 5-44│├1. Target Track Function - - - - - - - - - - - - - - - - - - - - section 5.6.2.2 on page 5-44│├2. Target Track Color- - - - - - - - - - - - - - - - - - - - - - section 5.6.2.1 on page 5-44││├1. All││├2. Target Track No.1││├3. Target Track No.2││├4. Target Track No.3││├5. Target Track No.4││├6. Target Track No.5││├7. Target Track No.6││├8. Target Track No.7││├9. Next││├1. Target Track No.8││├2. Target Track No.9││├3. Target Track No.10││└4. Other│├3. Target Track Display- - - - - - - - - - - - - - - - - - - - - section 5.6.2.4 on page 5-46││├1. All││├2. Target Track No.1││├3. Target Track No.2││├4. Target Track No.3││├5. Target Track No.4││├6. Target Track No.5││├7. Target Track No.6││├8. Target Track No.7││├9. Next││├1. Target Track No.8││├2. Target Track No.9││├3. Target Track No.10││└4. Other│├4. Track Memory Interval - - - - - - - - - - - - - - - - - - - - section 5.6.2.5 on page 5-47│├5. Clear Track Color - - - - - - - - - - - - - - - - - - - - - - section 5.6.2.6 on page 5-47│├6. Clear Track Number│└7. File Operations - - - - - - - - - - - - - - - - - - - - - - - section 5.6.2.7 on page 5-48││├1. Select Card Slot││├2. Load Mode││├3. Load - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 5-48││├4. Save - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 5-49││├5. Erase - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 5-51││└6. Card T.TRK Display - - - - - - - - - - - - - - - - - - - - - - - - - page 5-52├3. Trial Maneuver - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.7 on page 5-53│├1. Trial Function│├2. Course(EBL)│├3. Speed(VRM)│├4. Vector Time│├5. Time to Maneuver│└6. Own Ship's Dynamic Trait││├1. Reach││├3. Turn Radius││├4. Acceleration││└5. Deceleration├4. Target Number Display - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.4 on page 5-18└9. TT Test Menu - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.7 on page 5-21│├1. Test Video- - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.7.1 on page 5-22│├2. TT Simulator - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.7.2 on page 5-23│├3. Status - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.7.3 on page 5-24│└4. Gate Display - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.7.4 on page 5-25

C－8JMA-9100 Instruction Manual > C.Menu Index > C.4 AISC.4 AIS├1. Association Setting - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.4.2 on page 5-37│├1. Association│├2. Proprity│├3. Bearing│├4. Range│├5. Course│├6. Speed│└7. Applicable AIS Target├2. Target Track Setting - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.6.2 on page 5-44│├1. Target Track Function - - - - - - - - - - - - - - - - - - - - section 5.6.2.2 on page 5-44│├2. Target Track Color- - - - - - - - - - - - - - - - - - - - - - section 5.6.2.1 on page 5-44││├1. All││├2. Target Track No.1││├3. Target Track No.2││├4. Target Track No.3││├5. Target Track No.4││├6. Target Track No.5││├7. Target Track No.6││├8. Target Track No.7││├9. Next││├1. Target Track No.8││├2. Target Track No.9││├3. Target Track No.10││└4. Other│├3. Target Track Display- - - - - - - - - - - - - - - - - - - - - section 5.6.2.4 on page 5-46││├1. All││├2. Target Track No.1││├3. Target Track No.2││├4. Target Track No.3││├5. Target Track No.4││├6. Target Track No.5││├7. Target Track No.6││├8. Target Track No.7││├9. Next││├1. Target Track No.8││├2. Target Track No.9││├3. Target Track No.10││└4. Other│├4. Track Memory Interval - - - - - - - - - - - - - - - - - - - - section 5.6.2.5 on page 5-47│├5. Clear Track Color - - - - - - - - - - - - - - - - - - - - - - section 5.6.2.6 on page 5-47│├6. Clear Track Number│└7. File Operations - - - - - - - - - - - - - - - - - - - - - - - section 5.6.2.7 on page 5-48││├1. Select Card Slot││├2. Load Mode││├3. Load - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 5-48││├4. Save - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 5-49││├5. Erase - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 5-51││└6. Card T.TRK Display - - - - - - - - - - - - - - - - - - - - - - - - - page 5-52├3. Trial Maneuver - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.7 on page 5-53│├1. Trial Function│├2. Course(EBL)│├3. Speed(VRM)│├4. Vector Time│├5. Time to Maneuver│└6. Own Ship's Dynamic Trait││├1. Reach││├2. Turn Radius││├3. Acceleration││└4. Deceleration├4. AIS Filter Setting - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.7 on page 5-32│├1. Filter Type- - - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.7.2 on page 5-32│├2. Make AIS Filter - - - - - - - - - - - - - - - - - - - - - - - section 5.3.7.3 on page 5-33

JMA-9100 Instruction Manual > C.Menu Index > C.5 AZC－9C│├3. Filter Display - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.7.4 on page 5-34│├4. ENT│└6. Filter Mode - - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.7.5 on page 5-34├5. Target Number Display - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.6 on page 5-31├6. AIS Alarm Setting - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.9 on page 5-36│├1. Lost Alarm- - - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.9.1 on page 5-36│└2. CPA/TCPA Alarm - - - - - - - - - - - - - - - - - - - - - - section 5.3.9.2 on page 5-36├7. Message - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.5.5 on page 5-29│├1. Addressed Message│└2. Broadcast Message├8. Display Lost TGT Data - - - - - - - - - - - - - - - - - - - - - - - section 5.3.5.6 on page 5-31└9. Own Ship's AIS Data - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.5.7 on page 5-31C.5 AZ├1. AZ 1- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.1.1 on page 5-14├2. AZ 2- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.1.1 on page 5-14├3. Make AZ 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.1.1 on page 5-14├4. Make AZ 2 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.1.1 on page 5-14└5. ENT

C－10JMA-9100 Instruction Manual > C.Menu Index > C.6 TrackC.6 Track├1. DISP Own Track Color - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.2 on page 3-40│├1. All│├2. White│├3. Cyan│├4. Blue│├5. Green│├6. Yellow│├7. Pink│└8. Red├2. Clear Own Track Color - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.5 on page 3-42├3. Track Type - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.6 on page 3-42├4. Num/Vector Display - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.6 on page 3-42├5. File Operations│├1. Select Card Slot│├2. Load Mode│├3. Load│├4. Save│├5. Erase│└6. Card Own Track Display├6. Water Depth Setting - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.7 on page 3-44│├1. Depth setting (MIN)│├2. Depth setting│├3. Depth setting│├4. Depth setting│├5. Depth setting│└6. Depth setting (MAX)├7. Water TEMP Setting- - - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.8 on page 3-45│├1. Temperature setting (MIN)│├2. Temperature setting │├3. Temperature setting │├4. Temperature setting │├5. Temperature setting │└6. Temperature setting (MAX)├8. Current Setting - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.9 on page 3-46│├1. Current Size│├2. Layer A│├3. Layer B│└4. Layer C

JMA-9100 Instruction Manual > C.Menu Index > C.7 RouteC－11CC.7 Route├1. Select Route - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.1 on page 3-67├2. WPT/Route Settig│├1. Waypoint Alarm - - - - - - - - - - - - - - - - - - - - - - - section 3.7.4.1 on page 3-79│├2. Route Alarm - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.4.2 on page 3-80│├3. Set Route Sequence- - - - - - - - - - - - - - - - - - - - - - section 3.7.2 on page 3-68││├1. Planned Speed - - - - - - - - - - - - - - - - - - - section 3.7.3.5 on page 3-77││├2. Add - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.2.2 on page 3-69││├3. Correct Position - - - - - - - - - - - - - - - - - - - section 3.7.2.3 on page 3-70││├4. Correct Planned Speed - - - - - - - - - - - - - - - section 3.7.2.4 on page 3-71││├5. Delete - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.2.5 on page 3-72││├6. Insert - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.2.6 on page 3-73││└7. New Monitor Route - - - - - - - - - - - - - - - - - section 3.7.2.1 on page 3-68│├6. Waypoint Input - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.3 on page 3-75│├7. Save Temporary Route│├8. Off-Track Limit Line - - - - - - - - - - - - - - - - - - - - - section 3.7.6.1 on page 3-83│├9. Next│├1. SEL. NUM/Comment Size - - - - - - - - - - - - - - - - - - section 3.7.6.2 on page 3-83│├2. Waypoint Vector- - - - - - - - - - - - - - - - - - - - - - - section 3.7.6.3 on page 3-84│├3. Status of Origin/DEST - - - - - - - - - - - - - - - - - - - - section 3.7.6.4 on page 3-85│└4. WPT Number Display - - - - - - - - - - - - - - - - - - - - section 3.7.6.5 on page 3-85├3. WPT/Route Operations - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.5 on page 3-81│├1. Route Sequence- - - - - - - - - - - - - - - - - - - - - - - section 3.7.5.1 on page 3-81│├2. Waypoint Switch Mode - - - - - - - - - - - - - - - - - - - section 3.7.6.6 on page 3-86│├3. Waypoint Skip - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.5.2 on page 3-82│├4. Waypoint Back Skip - - - - - - - - - - - - - - - - - - - - - section 3.7.5.2 on page 3-82│├5. Set/Cancel Waypoint│└6. Clear WPT/Route Data├4. File Operations - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.8 on page 3-87│├1. Select Card Slot - - - - - - - - - - - - - - - - - - - - - - - section 3.7.8.1 on page 3-87│├2. Load - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.8.3 on page 3-88│├3. Save - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.8.2 on page 3-87│└4. Erase - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.8.4 on page 3-89

C－12JMA-9100 Instruction Manual > C.Menu Index > C.8 U.MapC.8 U.Map├1. Own Ship Position - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.3.1 on page 3-52├2. Edit User Map - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.3 on page 3-52│├1. Make with Cursor - - - - - - - - - - - - - - - - - - - - - - section 3.6.1.1 on page 3-47││├1. Type││└2. Color│├2. Make with L/L - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.1.3 on page 3-49││├1. Type││├2. Color││├3. L/L││├4. Comment││├5. Enter││└9. New Line Input/9.New Mark Input│├3. Move - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.3.2 on page 3-53│├4. Delete - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.3.3 on page 3-55│├5. Insert/Move Vertex - - - - - - - - - - - - - - - - - - - - - section 3.6.3.4 on page 3-56│├6. Delete Vertex - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.3.6 on page 3-58│└7. Delete by Type by Color - - - - - - - - - - - - - - - - - - - section 3.6.3.7 on page 3-59├3. Shift - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.4.1 on page 3-60├4. Shift Clear - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.4.2 on page 3-61├5. Mark Display Setting- - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.2 on page 3-50│├1. Display Mark Type- - - - - - - - - - - - - - - - - - - - - - section 3.6.2.1 on page 3-50││├1. All││├2. ○││├3. △││├4. ▽││├5. □││├6. ◇││├7. Wreck (mark)││├8. △△││├9. Next││├1. ▽▽││├2. △▽││├3. ▽△││├4. ＋││├5. ×││├6. Ｙ││├7. Hand drum (mark)││├8. Light house (mark)││├9. Next││├1. Trapezoid（mark）││├2. filled Trapezoid（mark）││├3. Hat(mark)││├4. ●●││├5. ●││├6. Filled Triangle(mark)││├7. ！││├8. anchor(mark)││├9. Next││├1. slash-anchor(mark)││├2. circle-dotted line(mark)││├3. non-dangerous wreck(mark)││├4. ◎││├5. mariner's event mark(mark)││├6. ・││├7. Wavy line (mark)││├8. Solid line (mark)││└9. Dashed-dotted line (mark)│├2. Display Mark Color - - - - - - - - - - - - - - - - - - - - - section 3.6.2.2 on page 3-51││├1. All││├2. White││├3. Cyan││├4. Blue

JMA-9100 Instruction Manual > C.Menu Index > C.8 U.MapC－13C││├5. Green││├6. Yellow││├7. Pink││└8. Red│├3. Mark Size - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.2.3 on page 3-51│└4. Comment Font Size - - - - - - - - - - - - - - - - - - - - - section 3.6.2.4 on page 3-52├6. Geodetic - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.6 on page 3-65└7. File Operations - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.5 on page 3-61│├1. Select Card Slot│├2. Load Mode - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.5.1 on page 3-61│├3. Load - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.5.1 on page 3-61│├4. Unload - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.5.2 on page 3-62│├5. Save - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.5.3 on page 3-62│├6. Erase - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.5.4 on page 3-63│└7. Card Mark Display - - - - - - - - - - - - - - - - - - - - - - section 3.6.5.5 on page 3-64

C－14JMA-9100 Instruction Manual > C.Menu Index > C.9 Serviceman MenuC.9 Serviceman Menu├Serviceman Menu - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.1.1 on page 7-1├1. Adjust Menu│├1. Tune Adjustment - - - - - - - - - - - - - - - - - - - - - - - - section 7.1.3 on page 7-5│├2. Bearing Adjustment - - - - - - - - - - - - - - - - - - - - - - - section 7.1.4 on page 7-7│├3. Range Adjustment - - - - - - - - - - - - - - - - - - - - - - - - section 7.1.5 on page 7-7│└4. TXRX Adjustment││├1. Antenna Height - - - - - - - - - - - - - - - - - - - - - section 7.1.8 on page 7-9││├2. Tune Peak Adjustment- - - - - - - - - - - - - - - - - section 7.1.3.1 on page 7-5││├3. Tune Indicator Adjust - - - - - - - - - - - - - - - - - section 7.1.3.2 on page 7-6││├4. MON Adjustment - - - - - - - - - - - - - - - - - - section 7.3.4.1 on page 7-31││├5. MON Indicator Adjustment - - - - - - - - - - - - - - section 7.3.4.2 on page 7-32││└6. Output Pulse - - - - - - - - - - - - - - - - - - - - - section 7.2.4 on page 7-18├2. Installation Menu│├1. Installation Information- - - - - - - - - - - - - - - - - - - - - section 7.2.8 on page 7-21││├1. Date││├2. Name││└3. Company│├2. Master/Slave - - - - - - - - - - - - - - - - - - - - - - - - section 7.2.5.1 on page 7-19│├3. Sector Blank- - - - - - - - - - - - - - - - - - - - - - - - - - section 7.2.2 on page 7-16││├1. Sector1 - - - - - - - - - - - - - - - - - - - - - - - section 7.2.2.1 on page 7-16││├2. Sector2 - - - - - - - - - - - - - - - - - - - - - - - section 7.2.2.1 on page 7-16││├3. Sector3 - - - - - - - - - - - - - - - - - - - - - - - section 7.2.2.1 on page 7-16││├4. Make Sector1 - - - - - - - - - - - - - - - - - - - - section 7.2.2.2 on page 7-16││├5. Make Sector2 - - - - - - - - - - - - - - - - - - - - section 7.2.2.2 on page 7-16││└6. Make Sector3 - - - - - - - - - - - - - - - - - - - - section 7.2.2.2 on page 7-16│├4. CCRP Setting - - - - - - - - - - - - - - - - - - - - - - - - - section 7.1.9 on page 7-10│├5. COM Port Setting - - - - - - - - - - - - - - - - - - - - - - - section 7.2.1 on page 7-12││├1. Baud Rate- - - - - - - - - - - - - - - - - - - - - - section 7.2.1.1 on page 7-12│││├1. COMPASS│││├2. MAINTENANCE/LOG│││├3. NAV1│││├4. NAV2│││├5. ALARM│││├6. JARPA│││├7. AIS│││├8. BRIDGE NET│││├9. Next│││├1. ARPA│││└2. COM││├2. RX Port - - - - - - - - - - - - - - - - - - - - - - - section 7.2.1.2 on page 7-13│││├1. GPS│││├2. DLOG│││├3. Alarm│││├4. Depth│││├5. Temperature│││├6. Wind│││├7. Current│││├8. ROT│││├9. Next│││└1. RSA││├3. RX Sentence - - - - - - - - - - - - - - - - - - - - section 7.2.1.3 on page 7-14│││├1. GPS(LL/COG/SOG)│││├2. GPS(WPT/TIME)│││├3. Depth│││├4. Wind│││└5. Current││││├1. Data Set Number││││├2. Layer A││││├3. Layer B││││└4. Layer C││├4. TX Port - - - - - - - - - - - - - - - - - - - - - - - section 7.2.1.4 on page 7-15│││├1. TTM(TT)

JMA-9100 Instruction Manual > C.Menu Index > C.9 Serviceman MenuC－15C│││├2. TLL(TT)│││├3. TTD(TT)│││├4. TLB(TT)│││├5. OSD│││├6. RSD│││├7. ALR│││├8. ACK│││├9. Next│││├1. TTM(AIS)│││├2. TLL(AIS)│││├3. TTD(AIS)│││├4. TLB(AIS)│││├5. Remote Maintenance│││├6. JRC-ARPA│││├7. NMEA0183 Output Format│││├8. NMEA0183 Talker│││├9. Next│││├1. NMEA0183 TX Interval│││├2. APB│││├3. BOD│││├4. GGA│││├5. GLL│││├6. RMC│││├7. RMB│││├8. VTG│││├9. Next│││├1. XTE│││├2. BWC│││├3. HDT│││└4. THS││├7. Line Monitor│││├1. COMPASS│││├2. MAINTENANCE/LOG│││├3. NAV1│││├4. NAV2│││├5. ALARM│││├6. JARPA│││├7. AIS│││├8. BRIDGE NET│││├9. Next│││├1. ARPA│││├2. COM│││├3. TXRX/ISW│││├4. KEYBOARD1│││└5. KEYBOARD2│├6. Alarm System - - - - - - - - - - - - - - - - - - - - - - - - - section 7.2.9 on page 7-22││├1. Watch Alarm│││├1. Reset Interval - - - - - - - - - - - - - - - - section 7.2.9.1 on page 7-22│││└2. Trackball Threshold - - - - - - - - - - - - - section 7.2.9.2 on page 7-22││├2. Relay Output - - - - - - - - - - - - - - - - - - - - section 7.2.9.3 on page 7-23│││├1. Relay Output Mode│││├2. TT CPA/TCPA│││├3. AIS CPA/TCPA│││├4. New Target│││├5. Lost│││└6. RADAR Alarm││├3. ALR Output - - - - - - - - - - - - - - - - - - - - - section 7.2.9.4 on page 7-23│││├1. System Alarm│││└2. TT/AIS Alarm││├4. Sound Output Mode - - - - - - - - - - - - - - - - - section 7.2.9.6 on page 7-25││├5. External ACK Setting - - - - - - - - - - - - - - - - section 7.2.9.5 on page 7-24│││├1. Critical Alarm││││├1. Audio││││├2Indication││││└3. Acknowledge State│││├2. Normal Alarm││││├1. Audio││││├2. Indication││││└3. Acknowledge State│├7. Inter Switch

C－16JMA-9100 Instruction Manual > C.Menu Index > C.9 Serviceman Menu││├1. ISW Install││├2. Mask Setting│││├1. No.1 Connection/No.1 Master│││├2. No.2 Connection/No.2 Master│││├3. No.3 Connection/No.3 Master│││├4. No.4 Connection/No.4 Master│││├5. No.5 Connection/No.5 Master1│││├6. No.6 Connection/No.6 Masteri│││├7. No.7 Connection/No.7 Masteri│││└8. No.8 Connection/No.8 Masteri││└3. S-ISW TXRX Power Supply│├8. Language - - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.2.6 on page 7-20│├9. Next│├1. Input BP Count - - - - - - - - - - - - - - - - - - - - - - - section 7.2.5.2 on page 7-19│├2. TNI Blank - - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.2.3 on page 7-17││├1. TNI Blank - - - - - - - - - - - - - - - - - - - - - - section 7.2.3.1 on page 7-17││└2. Make Sector- - - - - - - - - - - - - - - - - - - - - section 7.2.3.2 on page 7-17│├3. Device Installation - - - - - - - - - - - - - - - - - - - - - - - - section 7.1.6 on page 7-8││├1. Gyro││├2. Compass││├3. GPS Compass││├4. LOG││├5. 2AXW││├6. 2AXG││└7. GPS│├4. Network││├1. Network Function││└2. IP Address├3. Maintenance Menu│├1. Safety Switch - - - - - - - - - - - - - - - - - - - - - - - - - section 7.4.1 on page 7-33│├2. Area Initial- - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.4.2 on page 7-34││└1. Partial Master Reset - - - - - - - - - - - - - - - - - section 7.4.2.1 on page 7-34│││├1. Serviceman Menu│││├2. Except Serviceman Menu│││├3. User Setting│││├4. TT Setting│││├5. AIS Setting│││├6. Day/Night│││└7. JRC Card Copy Record││└2. All Master Reset- - - - - - - - - - - - - - - - - - - section 7.4.2.2 on page 7-34│├3. Internal To Card2 - - - - - - - - - - - - - - - - - - - - - - section 7.4.3.1 on page 7-35│├4. Card2 To Internal - - - - - - - - - - - - - - - - - - - - - - section 7.4.3.2 on page 7-35│├5. TXRX Time - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.4.4 on page 7-36││├1. Clear TX Time- - - - - - - - - - - - - - - - - - - - section 7.4.4.1 on page 7-36││├2. Clear Motor Time - - - - - - - - - - - - - - - - - - section 7.4.4.2 on page 7-36││├3. TXRX to Display Unit - - - - - - - - - - - - - - - - section 7.4.4.3 on page 7-37││└4. Display Unit to TXRX - - - - - - - - - - - - - - - - section 7.4.4.4 on page 7-37│└6. String Data Update - - - - - - - - - - - - - - - - - - - - - - section 7.4.5 on page 7-38└9. RADAR/TT Initial Setup│├1. Signal Processing - - - - - - - - - - - - - - - - - - - - - - - section 7.3.1 on page 7-26││├1. Echo Noise Level - - - - - - - - - - - - - - - - - - section 7.3.1.1 on page 7-26││└2. Setting Mode - - - - - - - - - - - - - - - - - - - - section 7.3.1.2 on page 7-27│├2. TT- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.3.2 on page 7-27││├1. Vector Constant - - - - - - - - - - - - - - - - - - - section 7.3.2.1 on page 7-27││├2. Video TD Level - - - - - - - - - - - - - - - - - - - section 7.3.2.2 on page 7-28││├3. Video High Level││├4. Video Low Level││├5. Gate Size││└6. Limit Ring│└3. MBS- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.3.3 on page 7-29││├1. MBS Level- - - - - - - - - - - - - - - - - - - - - - section 7.3.3.1 on page 7-29││└2. MBS Area - - - - - - - - - - - - - - - - - - - - - - section 7.3.3.2 on page 7-301.Only for ISW Extended Mode

MARINE RADARMARINE RADAREQUIPMENTEQUIPMENTINSTRUCTIONINSTRUCTIONMANUALMANUALJMA-9133-SAJMA-9133-SAJMA-9132-SAJMA-9132-SAJMA-9123-7XA/9XAJMA-9123-7XA/9XAJMA-9122-6XA/9XA/6XAHJMA-9122-6XA/9XA/6XAHJMA-9110-6XA/6XAHJMA-9110-6XA/6XAH01ETM ISO 9001, ISO 14001 CertifiedPrinted in JapanMarine Service Department+81-3-3492-1305+81-3-3779-1420tmsc@jrc.co.jpTelephone :Facsimile :e-mail :AMSTERDAM BranchTelephone :Facsimile :e-mail :+31-20-658-0750+31-20-658-0755service@jrcams.nlSEATTLE BranchTelephone :Facsimile :e-mail :+1-206-654-5644+1-206-654-7030service@jrcamerica.comCODE No.7ZPRD0685CODE No.7ZPRD0685MAY. 2008 Edition 2 JRCMAY. 2008 Edition 2 JRCNot use the asbestos For further information,contact:URL http://www.jrc.co.jp

Navigation menu