Japan Radio Co NKE1130 Marine Radar User Manual JMA 9100 series RADAR Instruction Manual
Japan Radio Co Ltd. Marine Radar JMA 9100 series RADAR Instruction Manual
Contents
- 1. Users Manual 1
- 2. Users Manual 2
- 3. Users Manual 3
- 4. Users Manual
Users Manual 3
JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS
8－33
8
8.4.4 Replacement of LCD Monitor
8.4.4.1 Display Unit NCD-4990
Do not touch the LCD screen directly with your fingers.
Do not touch the AR filter directly with your fingers.
Perform the replacement work on a soft cloth to avoid damage to the LCD screen and
other parts.
[Required tools]
•
A Phillips screwdriver for 4 mm screws
•
A Phillips screwdriver for 6 mm screws
[Disassembly]
1)
Remove the tilt fixing handle (standalone type
only).
2)
Tilt up the screen as much as you can
(standalone type only).
Replacement of LCD monitor must be made by specialized
service personnel.
For details, refer to Service Manual.
8－34
JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS
3)
Remove the screws (M6) from the four
corners and displace the face cover.
4)
LRemove the LCD operation circuit
cables and remove the face cover.
5)
Remove six M4 screws.
Remove
Remove
Remove
Remove
JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS
8－35
8
6)
Displace the module and remove the three
cables.
7)
Remove the LCD module.
[Assembly]
1)
Tighten the lower three M4 screws halfway.
2)
Connect the cables to the LCD module.
3)
Align the module to the lower three screws
and insert it downward.
4)
Check the positions of the two bosses and
ensure that appropriate space is maintained
under the LCD module. Tighten the six
screws evenly.
5)
Connect the LCD operation circuit cables
and attach the face cover.
6)
Tighten the screws at the four corners.
7)
Attach the tilt fixing handle.
[Operation Check]
1)
After completing the replacement
procedures, start the system to make sure that images are displayed properly.
2)
Turn the brightness knob to make sure the brightness can be changed between the
minimum and the maximum levels.
Remove
Temporary
tightening
Positions of the
two bosses
8－36
JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS
8.4.5 Replacement of Backup Battery
A coin-cell battery maintains radar system configuration, date, and time
information while power off condition. Radar system configuration is saving to
non-volatile memory at fixed intervals.
8.4.5.1 About the Battery Alarm
If is appeared at the lower-right of the display when start up the
radar system, the battery has not enough time left to live. We recommend to
replace the battery.
If is appeared at the lower-right of the display when start up the
radar system, the battery has no time left to live. There is a necessary to replace
the battery. In This condition, this radar system is restored configuration
information from flash memory and normal operation is available. However, you
turned of the radar system before saving to flash memory, the configuration
information is maybe lost. In this case, you must setup the configuration again.
8.4.5.2 How to Replacement of Backup Battery
[Required tools]
•
A flat tip screwdriver for 6 mm screws
•
A Phillips screwdriver for 4 mm screws
•
A flat tip nonconductive screwdriver for 3 mm screws
Replacement of backup battery must be made by specialized
service personnel.
For details, refer to Service Manual.
About disposal of used battery, refer to Section 10.2.
Battery Low
Battery Dead
JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS
8－37
8
[Disassembly]
1)
Remove the four fixing screws to remove
the cover from the display unit (NCD-
4990).
（A flat tip screwdriver for 6 mm screws）
For standalone type NCD-4990
For tabletop type: NDC-1399-9
2)
Remove the cable connected to the radar
processing circuit board.
The radar processing circuit is the first board
from the left.
3)
Remove the two fixing screws (M4).
4)
Pull out the board to the front.
5)
Insert the flat tip nonconductive screwdriver
for adjustment or some stick between the
battery and the battery holder and lift the
battery up.
Remove
Remove
Remove
8－38
JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS
6)
Insert the flat tip nonconductive sscrewdriver
for adjustment or some stick to the location
shown in the figure below and slide the battery
sideways to remove the battery.
[Assembly]
1)
Check the polarity of the battery. Make sure
that the battery's positive (+) side is facing up.
2)
Slide the battery sideways into the battery
holder.
3)
Make sure that the battery is inserted fully.
[Check Item]
1)
Check that no error message comes up.
2)
Check that the system starts up normally.
[Notes]
JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS
8－39
8
If you installed the battery with the wrong polarity, remove the battery immediately and
do not use the same battery again.
During the procedures, do not put the battery on any circuit board or conductive item.
To dispose of a used battery, follow the instructions provided in Section 10.2 "DISPOSAL
OF USED BATTERIES".
To disassemble of a used battery, have to use non-conductive tool.
8－40
JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS
TROUBLE SHOOTING AND AFTER-SALES SERVICE
9.1 FAULT FINDING .....................................................................................9-1
9.1.1 List of Alarms and other Indications .............................................9-1
9.1.2 Operation Checking ........................................................................9-5
9.1.3 Fuse Checking .................................................................................9-5
9.2 TROUBLE SHOOTING ...........................................................................9-6
9.2.1 Special Parts ....................................................................................9-7
9.2.2 Circuit Block to be Repaired ..........................................................9-8
9.3 AFTER-SALES SERVICE ....................................................................9-14
9.3.1 Keeping period of maintenance parts .........................................9-14
9.3.2 When you Request for Repair ......................................................9-14
9.3.3 Recommended Maintenance ........................................................9-14
SECTION 9
TROUBLE SHOOTING AND
AFTER-SALES SERVICE
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDING
9－1
9
9.1 FAULT FINDING
In case of semiconductor circuits, it is deemed that there are few cases in which
the used semiconductor devices have inferior quality or performance deterioration
except due to insufficient design or inspection or by other external and artificial
causes. In general, the relatively many causes are disconnection in a high-value
resistor due to moisture, a defective variable resistor and poor contact of a switch
or relay.
Some troubles are caused by defective parts, imperfect adjustment (such as tuning
adjustment) or insufficient service (such as poor cable contact). It will also be
effective to check and readjust these points.
9.1.1 List of Alarms and other Indications
The system automatically recognizes an internal alarm and displays the alarm
message. If an event which is not trouble but must be reported to the operator
occurs, the system notifies the operator of the event.
Error message and alarm are displayed in the lower right of the display. For more
details refer to page2-31 Alarm.
This section gives the list of alarms displayed by the system and other display
lists.
Table9-1： List of System Error Message
Message Description
TXRX (SSW Off) Scanner: Safety switch OFF.
TXRX (AZI) Scanner: BP error.
TXRX (HL) Scanner: HL error.
TXRX (MHV) Scanner: Modulator's high voltage alarm.
TXRX (Data) Scanner: No communication, communication mismatched,
checksum error, or collision.
TXRX (Heater) Scanner: Magnetron heater voltage error.
TXRX (Reverse) Scanner: Reverse rotation.
9－2
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDING
TXRX (Video) Scanner: VIDEO error.
TXRX (Trigger) Scanner: TRIGGER error..
TXRX (Fan 1) Scanner: FAN 1 error.
TXRX (Fan 2) Scanner: FAN 2 error.
TXRX (Motor) Scanner: Motor current error.
Keyboard (Data) Operation unit: Communication error or checksum error.
Keyboard2 (Data) Second operation unit: Communication error or checksum error.
GYRO I/F (Data) GYRO I/F: No communication or checksum error.
GYRO I/F (GYRO) GYRO I/F: GYRO error (error bit detected).
GYRO I/F (Log) GYRO I/F: Log error (error bit detected).
GPS (Status) GPS status error.
Position (Data) Latitude / longitude data: No communication or data error.
Date (Data) Date data: No communication or data error.
Speed (Log) 1-axis log: No communication or data error.
Speed (2AXW) 2-axis log (speed over water): No communication or data error.
Speed (2AXG) 2-axis log (speed over ground): No communication or data error.
Speed (GPS) GPS speed: No communication or data error.
PROC (Interrupt) Process unit: Interrupt error.
PROC (AZI) Process unit: AZI error.
PROC (HL) Process unit: HL error.Error during interrupt from ASIC1 to
RADAR DSP.
ASIC1 to RADAR VIDEO error.
PROC (Video) Trigger error.
PROC (Trigger) Heading data: No communication or data error.
Heading (Data) Water depth: No communication or data error.
Depth (Data) Water temperature: No communication or data error.
TEMP. (Data) Wind direction/velocity: No communication or data error.
Wind (Data) Tidal current: No communication or data error.
Current (Data) Rate of Turn: No communication or data error.
ROT (Data) Rudder Sensor Angle: No communication or data error.
RSA (Data) APB: No communication or data error.
Autopilot (Data) LCD monitor: Fan error.
Fan (LCD) RADAR Process Unit Interconnection: Fan error.
Fan (Power) Power Supply: Fan error.
Fan (PROC) Scanner: Safety switch OFF.
Table9-2： List of Notification
Message Description
CCRP Changed CCRP is automatic changed.
Weather INFO Weather information is received.
Copying Display is capturing to file.
Table9-1： List of System Error Message
Message Description
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDING
9－3
9
Set GYRO Requires setting of true bearing.
TM Reset Use care of resetting TM.
POSN Reset Change the latitude and longitude sentence.
Table9-3： List of Target Tracking Alarms and AIS Function Alarms
メッセージ 内 容
CPA/TCPA There is a dangerous target.
Trial There is a dangerous target, when trial maneuver is active.
New Target Acquisition or activation of a target in the automatic acquisition
/ activation zone.
Lost Failure in tracking the target that has been under tracking.
Failure in receiving AIS target data for a specified time.
REF Target Decrease in the reference target accuracy.
MAX Target The maximum number of targets is under acquisition.
95% Capacity Over 95% of the maximum number of targets to be tracked.
AIS Max Target Maximum number of AIS targets.
AIS 95% Capacity Over 95% of the maximum number of AIS targets.
AIS ACT MAX Maximum number of AIS targets to be activated.
AIS ACT 95%
Capacity Over 95% of the maximum number of AIS targets to be
activated.
TT (Boot) Target tracking unit start failure.
TT (Data) The target tracking unit is malfunctioning.
AIS (Data) AIS: No communication or communication error.
AIS PROC (Data) AIS processing circuit: No communication or communication error.
AIS Alarm ***i
i. *** is a 3-digit number which is Local Alarm No in the ALR sentence.
AIS alarm (Up to 10 alarm messages can be displayed.).
Table9-4： List of Route Messages and Warnings
Message Description
Arrival Arrive at way point.
Break Off(WPT) Out of the way point.
Approach Approach the route.
Cross Track Error Go off the route.
Table9-5： List of Operational Error Messages and Warnings
Message Description
No Position Data Mark or line input when the latitude and longitude is invalid.
No Heading Data Target tracking operation or TM selection when bearing data is
invalid.
Out of Range Out of target acquisition range.
Table9-2： List of Notification
9－4
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDING
Invalid Range TM selection due to TM-disabled range (96 nm).
Zooming in a ZOOM-disabled range (0.125 nm).
MAX Point Tried to enter navigation information beyond the specified.
Can't Transmit Tried to transmit within 5 second after standby or when the
transmitter-receiver has any trouble.
Invalid Data Tried to enter any data beyond its range.
Invalid Connection The operator set performance monitor to on without selecting
straight.
No Card Card not detected yet.
Card Full Card capacity insufficient.
Format Card Unformatted card.
Invalid Card Invalid card.
Read Failed Read failure.
Write Failed Write failure.
Delete Failed Deletion failure.
Format Failed Format failure.
Copy Failed Copy failure.
Not Allowed General operation error.
No Object No object at the cursor-specified position.
Slave Mode Operation of a menu for the scanner unit when the slave mode
is active.
Table9-6： List of Conditions Messages
Message Description
GPS (HDOP) The HDOP level is increased (Decrease in the GPS accuracy.).
MON Test Performance monitor is active.
Scanner Rotating The scanner is rotating (When transmitter is standby state.).
Battery Low battery is weakening.
Battery Dead The battery is dead.
Table9-7： List of Interswitch Alarms and Messages
Message Description
Master Range CHG The range of the own display unit has changed due to
change in the range of the master display unit.
ISW Complete The switchover of the Interswitch ended normally.
ISW Busy Access to the ISW menu was made during interswitching.
TXRX Standby The scanner unit is in the standby mode.
ISW Straight Failed in straight connection when the Interswitch
system stops operating.
ISW Standby The Interswitch recovered normally.
ISW Time Out Failed in switching.
ISW Error The interswitch is disabled.
Table9-5： List of Operational Error Messages and Warnings
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDING
9－5
9
9.1.2 Operation Checking
When the system is operating, the operation status (located at the upper right of
the screen) is changing pictures.
If picture freeze occurred, turn off the system and restart the system.
9.1.3 Fuse Checking
Melted fuses are caused by any clear cause. When a fuse is replaced, it is
necessary to check the related circuits even if there is no trouble. In checking, note
that there is some dispersion in the fusing characteristics. Table 9-8 shows a list of
fuses used in the equipment.
Pattern CHG Failed Connection change failed.
Connection Masked Inhibition of control / connection is set.
Master Standby The master display unit does not transmit any signals.
ISW (Data) No communication, data mismatched, or checksum error.
Update ISW Software Tried to enter new TXRX function, when interswitch
software used old version.
Table9-8： Fuse List
Location Parts# Current
Rating Protection
Circuit Type
AC/DC Converter F501 10A Motor ST6-10AN1
GYRO Interface
circuit F1～F4 0.5A GYRO
Interface
circuit
MF60NR250V0.5
Table9-7： List of Interswitch Alarms and Messages
Operation Status
9－6
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING
9.2 TROUBLE SHOOTING
As this radar equipment includes complicated circuits, it is necessary to request a
specialist engineer for repair or instructions for remedy if any circuit is defective.
There are also troubles by the following causes, which should be referred to in
checking or repair work.
１ Poor Contact in Terminal Board of Inter-Unit Cables
a. Poor contact in terminal board
b. The cable end is not fully connected, that it, contacted with earthed another
terminal.
c. Disconnected cable wire
２ Poor Contact of Connector within Unit
This radar equipment is provided with Table 9-9 standard
spares.
Table9-9： 7ZXRD0025
Name Type/Code Shape (mm) In
use Spare Parts # Location
Fuse MF60NR250V0.5
(5ZFGD00006)
412 F1～F4 GYRO I/F
CMJ-462E
Fuse ST6-10AN1
(5ZFCA00053)
13 F501 AC/DC Converter
NBA-5135
i
30
Φ6.4
31.8
Φ6.35
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING
9－7
9
9.2.1 Special Parts
NKE-2103
NKE-1125/2254
NTG-3225
NKE-1130
NTG-3230
Table9-10： NKE-2103 (JMA-9110-6XA/6XAH、JMA-7110-6XA/6XAH)
Parts No. Name Type Manufacture Location Code
V101 Magnetron MAF1565N NJRC Scanner Unit 5VMAA00102
A101/A102 Circulator FCX68 Toshiba Scanner Unit 6AJRD00001
A301 Diode Limiter NJS6930 NJRC Scanner Unit 5ATBT00006
Table9-11： NKE-1125/2254 (JMA-9122-6XAH/9XA/6XAH、JMA-7122-6XA/9XA/6XAH)
Parts No. Name Type Manufacture Location Code
V101 Magnetron M1568BS NJRC Scanner Unit 5VMAA00106
A101/A102 Circulator NJC3901M NJRC Scanner Unit 5AJBV00007
A301 Diode Limiter NJS6930 NJRC Scanner Unit 5ATBT00006
Table9-12： NTG-3225 (JMA-9123-7XA/9XA、JMA-7123-7XA/9XA)
Parts No. Name Type Manufacture Location Code
V101 Magnetron M1568BS NJRC Transmitter
Receiver Unit 5VMAA00106
A101/A102 Circulator NJC3901M NJRC Transmitter
Receiver Unit 5AJBV00007
A301 Diode Limiter NJS6930 NJRC Transmitter
Receiver Unit 5ATBT00006
Table9-13： NKE-1130 (JMA-9132-SA、JMA-7132-SA)
Parts No. Name Type Manufacture Location Code
V101 Magnetron M1555 NJRC Scanner Unit 5VMAA00106
A101/A102 Circulator NJC3316 NJRC Scanner Unit 5AJBV00007
A301 Diode Limiter NJS6318 NJRC Scanner Unit 5ATBT00006
Table9-14： NTG-3230 (JMA-9133-SA、JMA-7133-SA)
Parts No. Name Type Manufacture Location Code
V101 Magnetron M1555 NJRC Transmitter
Receiver Unit 5VMAA00104
A101 Circulator NJC3317 NJRC Transmitter
Receiver Unit 5AJBV00009
A301 TR Limiter TL378A NJRC Transmitter
Receiver Unit 5VLAA00037
9－8
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING
9.2.2 Circuit Block to be Repaired
Table9-15： Circuit Block to be Repaired (JMA-9110-6XA/6XAH)
Location Circuit Block Type Remarks
SCANNER UNIT GEARED MOTOR 7BDRD0048 DC brushless motor (common
with HS)
SCANNER UNIT MODULATOR CIRCUIT CME-363 Excluding Magnetron
SCANNER UNIT RECEIVER UNIT NRG-610 Including CAE-529-1
SCANNER UNIT POWER SUPPLY CIRCUIT CBD-1783
SCANNER UNIT ENCODER CHT-71A
SCANNER UNIT MOTOR CONTROL POWER
SUPPLY CBD-1779
SCANNER UNIT FAN 7BFRD0002
RADAR
PROCESS UNIT RADAR PROCESS CIRCUIT MDLW11900 With mounting bracket
RADAR
PROCESS UNIT AIS PROCESS CIRCUIT CDC-1325
RADAR
PROCESS UNIT ARPA PROCESS CIRCUIT CDC-1186D
RADAR
PROCESS UNIT GYRO I/F CIRCUIT CMJ-462E
RADAR
PROCESS UNIT TERMINALBOARD CIRCUIT CQD-2097
RADAR
PROCESS UNIT MOTHERBOARD CIRCUIT CQC-1192
RADAR
PROCESS UNIT FAN (RPU) 109R0612S4D13
RADAR
PROCESS UNIT POWER SUPPLY CBD-1661
RADAR
PROCESS UNIT FAN (PSU) 7BFRD0006
OPERATION
UNIT OPERATION CIRCUIT A CCK-973
OPERATION
UNIT OPERATION CIRCUIT B CCK-974
OPERATION
UNIT OPERATION CIRCUIT D CCK-976
OPERATION
UNIT TRACKBALL 5EZLY00003
OPERATION
UNIT LCD PANEL 7WSRD0002A 23.1-inch LCD
OPERATION
UNIT LCD OPERATION CIRCUIT CCK-972
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING
9－9
9
Table9-16： Circuit Block to be Repaired (JMA-9122-6XA/9XA)
Location Circuit Block Type Remarks
SCANNER UNIT GEARED MOTOR MDBW10822 For 100/220VAC
SCANNER UNIT ENCODER CHT-71A
SCANNER UNIT AC220V MOTOR DRIVER 7EPRD0034 For 220VAC
SCANNER UNIT AC100V MOTOR DRIVER 7EPRD0035 For 100VAC
SCANNER UNIT PERFORMANCE MONITOR NJU-85
SCANNER UNIT HEATER CONTROL PART CHG-216 Option (AC100V)
SCANNER UNIT BREAK CIRCUIT CFA-253
SCANNER UNIT BREAK CONTROL CIRCUIT CCB-655
SCANNER UNIT BREAK CIRCUIT A CFA-259
SCANNER UNIT BREAK CIRCUIT B CFA-260
SCANNER UNIT T/R CONTROL CIRCUIT CMC-1205R
SCANNER UNIT MODULATOR UNIT NMA-550 Including CPA-264
Including CMB-404
Including CFR-229
Excluding Magnetron
SCANNER UNIT MODULATOR CIRCUIT CPA-264
SCANNER UNIT RECEIVER UNIT NRG-162A Including CMA-866A
SCANNER UNIT POWER SUPPLY CIRCUIT CBD-1682A
SCANNER UNIT RELAY FILTER CIRCUIT CSC-656
SCANNER UNIT FAN 7BFRD0002
RADAR PROCESS UNIT RADAR PROCESS CIRCUIT MDLW11900 With mounting bracket
RADAR PROCESS UNIT AIS PROCESS CIRCUIT CDC-1325
RADAR PROCESS UNIT ARPA PROCESS CIRCUIT CDC-1186D
RADAR PROCESS UNIT GYRO I/F CIRCUIT CMJ-462E
RADAR PROCESS UNIT TERMINALBOARD CIRCUIT CQD-2097
RADAR PROCESS UNIT MOTHERBOARD CIRCUIT CQC-1192
RADAR PROCESS UNIT FAN (RPU) 109R0612S4D13
RADAR PROCESS UNIT POWER SUPPLY CBD-1661
RADAR PROCESS UNIT FAN (PSU) 7BFRD0006
OPERATION UNIT OPERATION CIRCUIT A CCK-973
OPERATION UNIT OPERATION CIRCUIT B CCK-974
OPERATION UNIT OPERATION CIRCUIT D CCK-976
OPERATION UNIT TRACKBALL 5EZLY00003
MONITOR UNIT LCD PANEL 7WSRD0002A 23.1-inch LCD
MONITOR UNIT LCD OPERATION CIRCUIT CCK-972
9－10
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING
Table9-17： Circuit Block to be Repaired (JMA-9122-6XAH)
Location Circuit Block Type Remarks
SCANNER UNIT GEARED MOTOR 7BDRD0045A For 100/220VAC
SCANNER UNIT ENCODER CHT-71A
SCANNER UNIT MOTOR CONTROL POWER
CIRCUIT CBD-1779
SCANNER UNIT BREAK CIRCUIT CFA-257
SCANNER UNIT PERFORMANCE MONITOR NJU-85
SCANNER UNIT HEATER CONTROL PART CHG-216 Option (AC100V)
SCANNER UNIT POWER SUPPLY CIRCUIT CBD-1682A
SCANNER UNIT T/R CONTROL CIRCUIT CMC-1205R
SCANNER UNIT MODULATOR UNIT NMA-550 Including CPA-264
Including CMB-404
Including CFR-229
Excluding Magnetron
SCANNER UNIT MODULATOR CIRCUIT CPA-264
SCANNER UNIT RECEIVER UNIT NRG-162A Including CMA-866A
SCANNER UNIT FAN 7BFRD0002
RADAR PROCESS UNIT RADAR PROCESS CIRCUIT MDLW11900 With mounting bracket
RADAR PROCESS UNIT AIS PROCESS CIRCUIT CDC-1325
RADAR PROCESS UNIT ARPA PROCESS CIRCUIT CDC-1186D
RADAR PROCESS UNIT GYRO I/F CIRCUIT CMJ-462E
RADAR PROCESS UNIT TERMINALBOARD CIRCUIT CQD-2097
RADAR PROCESS UNIT MOTHERBOARD CIRCUIT CQC-1192
RADAR PROCESS UNIT FAN (RPU) 109R0612S4D13
RADAR PROCESS UNIT POWER SUPPLY CBD-1661
RADAR PROCESS UNIT FAN (PSU) 7BFRD0006
OPERATION UNIT OPERATION CIRCUIT A CCK-973
OPERATION UNIT OPERATION CIRCUIT B CCK-974
OPERATION UNIT OPERATION CIRCUIT D CCK-976
OPERATION UNIT TRACKBALL 5EZLY00003
MONITOR UNIT LCD PANEL 7WSRD0002A 23.1-inch LCD
MONITOR UNIT LCD OPERATION CIRCUIT CCK-972
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING
9－11
9
Table9-18： Circuit Block to be Repaired (JMA-9123-7XA/9XA)
Location Circuit Block Type Remarks
SCANNER UNIT GEARED MOTOR MDBW10822 For 100/220VAC
SCANNER UNIT ENCODER CHT-71A
SCANNER UNIT AC220V MOTOR DRIVER 7EPRD0034 For 220VAC
SCANNER UNIT AC100V MOTOR DRIVER 7EPRD0035 For 100VAC
SCANNER UNIT PERFORMANCE MONITOR NJU-85
SCANNER UNIT HEATER CONTROL PART CHG-216 Option (AC100V)
SCANNER UNIT BREAK CIRCUIT CFA-253
SCANNER UNIT BREAK CONTROL CIRCUIT CCB-655
SCANNER UNIT BREAK CIRCUIT A CFA-259
SCANNER UNIT BREAK CIRCUIT B CFA-260
TRANSMITTER
RECEIVER UNIT T/R CONTROL CIRCUIT CMC-1205R
TRANSMITTER
RECEIVER UNIT MODULATOR UNIT NMA-552 Including CPA-264
Including CMB-405
Including CFR-229
Excluding Magnetron
TRANSMITTER
RECEIVER UNIT MODULATOR CIRCUIT CPA-264
TRANSMITTER
RECEIVER UNIT RECEIVER UNIT NRG-162A Including CMA-866A
TRANSMITTER
RECEIVER UNIT POWER SUPPLY CIRCUIT CBD-1682A
TRANSMITTER
RECEIVER UNIT RELAY FILTER CIRCUIT CSC-656
RADAR PROCESS UNIT RADAR PROCESS CIRCUIT MDLW11900 With mounting bracket
RADAR PROCESS UNIT AIS PROCESS CIRCUIT CDC-1325
RADAR PROCESS UNIT ARPA PROCESS CIRCUIT CDC-1186D
RADAR PROCESS UNIT GYRO I/F CIRCUIT CMJ-462E
RADAR PROCESS UNIT TERMINALBOARD CIRCUIT CQD-2097
RADAR PROCESS UNIT MOTHERBOARD CIRCUIT CQC-1192
RADAR PROCESS UNIT FAN (RPU) 109R0612S4D13
RADAR PROCESS UNIT POWER SUPPLY CBD-1661
RADAR PROCESS UNIT FAN (PSU) 7BFRD0006
OPERATION UNIT OPERATION CIRCUIT A CCK-973
OPERATION UNIT OPERATION CIRCUIT B CCK-974
OPERATION UNIT OPERATION CIRCUIT D CCK-976
OPERATION UNIT TRACKBALL 5EZLY00003
MONITOR UNIT LCD PANEL 7WSRD0002A 23.1-inch LCD
MONITOR UNIT LCD OPERATION CIRCUIT CCK-972
9－12
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING
Table9-19： Circuit Block to be Repaired (JMA-9132-SA)
Location Circuit Block Type Remarks
SCANNER UNIT GEARED MOTOR MDBW10823 For 100/220VAC
SCANNER UNIT ENCODER CHT-71A1
SCANNER UNIT AC220V MOTOR DRIVER 7EPRD0034 For 220VAC
SCANNER UNIT AC100V MOTOR DRIVER 7EPRD0035 For 100VAC
SCANNER UNIT PERFORMANCE MONITOR NJU-84
SCANNER UNIT HEATER CONTROL PART CHG-215 Option (AC100V)
SCANNER UNIT BREAK CIRCUIT CFA-255
SCANNER UNIT BREAK CONTROL CIRCUIT CCB-655
SCANNER UNIT BREAK CIRCUIT A CFA-261
SCANNER UNIT BREAK CIRCUIT B CFA-262
SCANNER UNIT T/R CONTROL CIRCUIT CMC-1205R
SCANNER UNIT MODULATOR UNIT NMA-551 Including CPA-264
Including CMB-406
Including CFR-229
Exluding Magnetron
SCANNER UNIT MODULATOR CIRCUIT CPA-264
SCANNER UNIT RECEIVER UNIT NRG-229
SCANNER UNIT POWER SUPPLY CIRCUIT CBD-1682A
SCANNER UNIT RELAY FILTER CIRCUIT CSC-656
SCANNER UNIT FAN 7BFRD0002
RADAR PROCESS UNIT RADAR PROCESS CIRCUIT MDLW11900 With mounting bracket
RADAR PROCESS UNIT AIS PROCESS CIRCUIT CDC-1325
RADAR PROCESS UNIT ARPA PROCESS CIRCUIT CDC-1186D
RADAR PROCESS UNIT GYRO I/F CIRCUIT CMJ-462E
RADAR PROCESS UNIT TERMINALBOARD CIRCUIT CQD-2097
RADAR PROCESS UNIT MOTHERBOARD CIRCUIT CQC-1192
RADAR PROCESS UNIT FAN (RPU) 109R0612S4D13
RADAR PROCESS UNIT POWER SUPPLY CBD-1661
RADAR PROCESS UNIT FAN (PSU) 7BFRD0006
OPERATION UNIT OPERATION CIRCUIT A CCK-973
OPERATION UNIT OPERATION CIRCUIT B CCK-974
OPERATION UNIT OPERATION CIRCUIT D CCK-976
OPERATION UNIT TRACKBALL 5EZLY00003
MONITOR UNIT LCD PANEL 7WSRD0002A 23.1-inch LCD
MONITOR UNIT LCD OPERATION CIRCUIT CCK-972
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING
9－13
9
Table9-20： Circuit Block to be Repaired (JMA-9133-SA)
Location Circuit Block Type Remarks
SCANNER UNIT GEARED MOTOR MDBW10823 For 100/220VAC
SCANNER UNIT ENCODER CHT-71A1
SCANNER UNIT AC220V MOTOR DRIVER 7EPRD0034 For 220VAC
SCANNER UNIT AC100V MOTOR DRIVER 7EPRD0035 For 100VAC
SCANNER UNIT PERFORMANCE MONITOR NJU-84
SCANNER UNIT HEATER CONTROL PART CHG-215 Option (AC100V)
SCANNER UNIT BREAK CIRCUIT CFA-255
SCANNER UNIT BREAK CONTROL CIRCUIT CCB-655
SCANNER UNIT BREAK CIRCUIT A CFA-261
SCANNER UNIT BREAK CIRCUIT B CFA-262
TRANSMITTER
RECEIVER UNIT T/R CONTROL CIRCUIT CMC-1205R
TRANSMITTER
RECEIVER UNIT MODULATOR UNIT NMA-553 Including CPA-264
Including CMB-407
Including CFR-229
Exluding Magnetron
TRANSMITTER
RECEIVER UNIT MODULATOR CIRCUIT CPA-264
TRANSMITTER
RECEIVER UNIT RECEIVER UNIT NRG-229
TRANSMITTER
RECEIVER UNIT POWER SUPPLY CIRCUIT CBD-1682A
TRANSMITTER
RECEIVER UNIT RELAY FILTER CIRCUIT CSC-656
RADAR PROCESS UNIT RADAR PROCESS CIRCUIT MDLW11900 With mounting bracket
RADAR PROCESS UNIT AIS PROCESS CIRCUIT CDC-1325
RADAR PROCESS UNIT ARPA PROCESS CIRCUIT CDC-1186D
RADAR PROCESS UNIT GYRO I/F CIRCUIT CMJ-462E
RADAR PROCESS UNIT TERMINALBOARD CIRCUIT CQD-2097
RADAR PROCESS UNIT MOTHERBOARD CIRCUIT CQC-1192
RADAR PROCESS UNIT FAN (RPU) 109R0612S4D13
RADAR PROCESS UNIT POWER SUPPLY CBD-1661
RADAR PROCESS UNIT FAN (PSU) 7BFRD0006
OPERATION UNIT OPERATION CIRCUIT A CCK-973
OPERATION UNIT OPERATION CIRCUIT B CCK-974
OPERATION UNIT OPERATION CIRCUIT D CCK-976
OPERATION UNIT TRACKBALL 5EZLY00003
MONITOR UNIT LCD PANEL 7WSRD0002A 23.1-inch LCD
MONITOR UNIT LCD OPERATION CIRCUIT CCK-972
9－14
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.3 AFTER-SALES SERVICE
9.3 AFTER-SALES SERVICE
9.3.1 Keeping period of maintenance parts
Keeping period of maintenance parts is ten years from the production is
discontinued.
9.3.2 When you Request for Repair
If you suppose the product may be out of order, read the description in Section 9
carefully and check the suspected point again.
If it is still out of order, you are recommended to stop operation of the equipment
and consult with the dealer from whom you purchased the product, or our branch
office in your country or district, the sales department in our main office in Tokyo.
Repair within the Warranty Period
If any failure occurs in the product during its normal operation in accordance with
the instruction manual, the dealer or JRC will repair free of charge. In case that
any failure is caused due to misuse, faulty operation, negligence or force major
such as natural disaster and fire, the product will be repaired with charges.
Repair after the Warranty Period
If any defective function of the product is recoverable by repair, the repair of it
will be made at your own charge upon your request.
Necessary Information for Repair
•Product name, model, manufacturing date and serial number
•Trouble conditions (as detailed as possible. Refer to "Radar Failure Check
List" on page 9-15
•Name of company/organization, address and telephone number
9.3.3 Recommended Maintenance
The performance of the product may deteriorate due to the secular change of the
parts used in it, though such deterioration depends upon the conditions of
operation. So checkup and maintenance is recommendable for the product in
addition to your daily care.
For maintenance, consult with the near-by dealer or our sales department.Such
maintenance will be made with charges.
For further details of after-sale service, contact the JRC Offices.
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.3 AFTER-SALES SERVICE
9－15
9
Radar Failure Check List
Check the following items in the order of the number, and check the applicable
answer between YES or NO.
If the item cannot be determined as YES or NO, explain in detail in the item (18),
others.
i
When placing an order for repair of the product, it is requested that you could
confirm the check items and fill the results and sent the sheet to our contact.
If there is any unclear items, contact the ship on which the product is
installed, and give the correct information on the product.
Ship name: Phone: Fax:
iRadar general model name :JMA-
i. Write the full model name correctly
iSerial No. :
No. Check Item Result
(1) Power can be turned on. (The lamp on the Operation unit is lit) YES NO
(2)i
i. If result is NO, then check the fuse. (Refer to Section 9.1.2 "Operation Checking" and Section 9.2 "TROUBLE
SHOOTING")
A few minutes after powering-on, it will become standby status. YES NO
(3)iWhen powering-on (or TX ON), LCD monitor something is lit. YES NO
(4)i,ii The antenna rotates at the transmission (TX) ON. YES NO
(5)i,ii Current is supplied to the magnetron. (Refer to the instruction manual) YES NO
(6)ii
ii. Check these items while transmission is ON.
Turning is enabled. (Check with the range of 6 NM or more) YES NO
(7)ii Fixed marker is displayed. YES NO
(8)ii VRM is displayed. YES NO
(9)ii While noise is displayed while set at SEA and RAIN minimum, GAIN
maximum, IR-OFF and range 48 NM. YES NO
(10)ii Target reflection echo is displayed. YES NO
(11)ii Sensitivity of reflection echo is normal. YES NO
(12)ii EBL is displayed. YES NO
(13)ii Cursor mark moves. YES NO
(14)ii,iii
iii. Functions mentioned in the items (14), (15) and (17) may be optional, answer is not necessary.
GYRO course can be set and normally displayed. YES NO
(15)ii,iii LOG speed can be normally displayed. YES NO
(16)ii Target tracking function works normally. YES NO
(17)ii,iii If equipped with an interswitch, when switching from the straight mode (II) to
(X), the failures (items marked NO) in the above (1) to (16), are switched over
to the other unit.
YES NO
（18）Others (Error message, etc. )
DISPOSAL
10.1 DISPOSAL OF THE UNIT ....................................................................10-1
10.2 DISPOSAL OF USED BATTERIES .....................................................10-1
10.3 DISPOSAL OF USED MAGNETRON ..................................................10-2
10.4 DISPOSAL OF TR-TUBE .....................................................................10-2
10.5 ABOUT THE CHINA ROHS .................................................................10-3
SECTION 10
DISPOSAL
JMA-9100 Instruction Manual > 10.DISPOSAL > 10.1 DISPOSAL OF THE UNIT
10－1
10
10.1 DISPOSAL OF THE UNIT
When disposing of this unit, be sure to follow the local laws and regulations for
the place of disposal.
10.2 DISPOSAL OF USED BATTERIES
In this unit, Lithium batteries are used for the following parts:
Radar Processing circuit (CDC-1324): BT1 (Maxell: CR2032)
•Do not store used lithium batteries. Dispose of them in accordance with
regulations of local government.
•When disposing of used lithium batteries be sure to insulate the batteries by
taping the terminals. For disposal of batteries, be sure to follow the local
laws and regulations. For detail, consult with the dealer you purchased the
product our business office, or local government.
When disposing of used lithium batteries, be sure to
insulate the batteries by taping the terminals.
Otherwise, heat generation, explosion or a fire may
occur.
+ -
+ -
JMA-9100 Instruction Manual > 10.DISPOSAL > 10.3 DISPOSAL OF USED MAGNETRON
10－2
10
10.3 DISPOSAL OF USED MAGNETRON
Magnetron is used in the Scanner （NKE－2103/2254/1125/1130）and
Transmitter Receiver Unit (NTG-3225/3230).
•When the magnetron is replaced with a new one, return the used magnetron to
our dealer or business office.
For detail, consult with our dealer or business office.
10.4 DISPOSAL OF TR-TUBE
In the case that either mark shown in Fig 10-1 is on the expired TR-tube,
Radioisotopes are in the TR-tube.
•Disposal of TR-tube with these marks must be done in accordance with the
laws and regulations of the pertaining country. For detail, consult with our
dealer or business office.
•Radiation from TR-tube has no effect on the human body.
•Don't take apart TR-tube.
Fig 10-1: Radioisotopes Marks
JMA-9100 Instruction Manual > 10.DISPOSAL > 10.5 ABOUT THE CHINA ROHS
10－3
10
10.5 ABOUT THE CHINA ROHS
形式名(Type): JMA-9100 Series, JMA-7100Series 名称(Name): RADAR
铅 汞 镉 六价铬 多溴联苯 多溴二苯醚
(Pb) (Hg) (Cd) (Cr6+) (PBB) (PBDE)
雷达天线单元
(Scanner Unit)
××○×××
收发信单元
(Transmitter-receiver Unit)
××××××
主船内装置 (Inboard Unit)
・显示装置 (Display Unit)
・键盘装置 (OperationUnit)
・信号处理装置
(RADAR Process Unit)
××××××
外部设备 (Peripherals)
・选择 (Options)
・电线类 (Cables)
・手册 (Documennts)
××××××
有毒有害物质或元素的名称及含量
(Names & Content of toxic and hazardous substances or elements）
(Toxic and Hazardous Substances and Elements)
×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T11363-2006 标准规定的限量要求。
(Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials
used for this part is above the limit requirement in SJ/T 11363-2006.)
○：表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11306-2006 标准规定的限量要求以下。
(Indicates that this toxic, or hazardous substance contained in all of the homogeneous materials for this
part is below the requirement in SJ/T11363-2006.)
部件名称
(Part name)
有毒有害物质或元素
SPECIFICATION
11.1 JMA-9133-SA TYPE RADAR ...............................................................11-1
11.2 JMA-9132-SA TYPE RADAR............................................................... 11-2
11.3 JMA-9123-7XA/9XA TYPE RADAR ....................................................11-3
11.4 JMA-9122-6XA/9XA TYPE RADAR ....................................................11-4
11.5 JMA-9122-6XAH TYPE RADAR .........................................................11-5
11.6 JMA-9110-6XA TYPE RADAR ............................................................11-6
11.7 JMA-9110-6XAH TYPE RADAR .........................................................11-7
11.8 SCANNER UNIT (NKE-1139) ...............................................................11-8
11.9 SCANNER UNIT (NKE-1130) ...............................................................11-9
11.10 SCANNER UNIT (NKE-1129-7/9) ......................................................11-10
11.11 SCANNER UNIT (NKE-1125-6/9) .......................................................11-11
11.12 SCANNER UNIT (NKE-2254-6HS) .....................................................11-12
11.13 SCANNER UNIT (NKE-2103-6) ..........................................................11-13
11.14 SCANNER UNIT (NKE-2103-6HS) .....................................................11-14
11.15 TRANSMITTER RECEIVER UNIT (NTG-3230) .................................11-15
11.16 TRANSMITTER RECEIVER UNIT (NTG-3225) .................................11-16
11.17 DISPLAY UNIT (NCD-4990) ...............................................................11-17
SECTION 11
SPECIFICATION
11.18 Target Tracking Function .................................................................11-20
11.19 AIS FUNCTION ...................................................................................11-21
11.20 PERFORMANCE MONITOR (NJU-84) ..............................................11-22
11.21 PERFORMANCE MONITOR (NJU-85) ..............................................11-22
11.22 AC-DC CONVERTER (NBA-5135) .....................................................11-22
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.1 JMA-9133-SA TYPE RADAR
11 －1
11
11.1 JMA-9133-SA TYPE RADAR
GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125、0.25、0.5、0.75、1.5、3、6、12、24、48、96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70℃)
Other Unit -15 to +55℃
Relative humidity 93% at +40℃
Vibration 2 to 13.2Hz Amplitude +/-1mm +/-10%
13.2 to 100Hz Acceleration 7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.400VA typical
Approx. 2000VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-1139)
See 11.8
TRANSMITTER RECEIVER UNIT (NTG-3230)
See 11.15
DISPLAY UNIT (NCD-4990)
See 11.17
PERFORMANCE MONITOR (NJU-84)
See 11.20
OPTION
Scanner with Deicing Heater NKE-1139-D (Only heater collar)
Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length
SCANNER UNIT to
TRANSMITTER RECEIVER UNIT 30m
DISPLAY UNIT to
TRANSMITTER RECEIVER UNIT 35m
SAFE DISTANCE FOR STANDARD COMPASS
SCANNER UNIT 1.4m
TRANSMITTER RECEIVER UNIT 3.9m
DISPLAY UNIT 4.0m
11 －2
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.2 JMA-9132-SA TYPE RADAR
11.2 JMA-9132-SA TYPE RADAR
GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70℃)
Other Unit -15 to +55℃
Relative humidity 93% at +40℃
Vibration 2 to 13.2Hz Amplitude +/-1mm +/-10%
13.2 to 100Hz Acceleration 7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.400VA typical
Approx. 2000VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-1130)
See 11.9
DISPLAY UNIT (NCD-4990)
See 11.17
PERFORMANCE MONITOR (NJU-84)
See 11.20
OPTION
Scanner with Deicing Heater NKE-1139-D (Only heater collar)
Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length
SCANNER UNIT to
TRANSMITTER RECEIVER UNIT 65m
SAFE DISTANCE FOR STANDARD COMPASS
SCANNER UNIT 5.1m
DISPLAY UNIT 4.0m
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.3 JMA-9123-7XA/9XA TYPE RADAR
11 －3
11
11.3 JMA-9123-7XA/9XA TYPE RADAR
GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70℃)
Other Unit -15 to +55℃
Relative humidity 93% at +40℃
Vibration 2 to 13.2Hz Amplitude +/-1mm +/-10%
13.2 to 100Hz Acceleration 7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.350VA typical
Approx. 1700VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-1129-7/9)
See 11.10
TRANSMITTER RECEIVER UNIT (NTG-3225)
See 11.16
DISPLAY UNIT (NCD-4990)
See 11.17
PERFORMANCE MONITOR (NJU-85)
See 11.21
OPTION
Scanner with Deicing Heater NKE-1139-D (Only heater collar)
Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length
SCANNER UNIT to
TRANSMITTER RECEIVER UNIT 30m
DISPLAY UNIT to
TRANSMITTER RECEIVER UNIT 35m
SAFE DISTANCE FOR STANDARD COMPASS
SCANNER UNIT 1.05m
TRANSMITTER RECEIVER UNIT 2.8m
DISPLAY UNIT 4.0m
11 －4
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.4 JMA-9122-6XA/9XA TYPE RADAR
11.4 JMA-9122-6XA/9XA TYPE RADAR
GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70℃)
Other Unit -15 to +55℃
Relative humidity 93% at +40℃
Vibration 2 to 13.2Hz Amplitude +/-1mm +/-10%
13.2 to 100Hz Acceleration 7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.350VA typical
Approx. 1700VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-1125-6/9)
See 11.11
DISPLAY UNIT (NCD-4990)
See 11.17
PERFORMANCE MONITOR (NJU-85)
See 11.21
OPTION
Scanner with Deicing Heater NKE-1139-D (Only heater collar)
Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length
SCANNER UNIT to
TRANSMITTER RECEIVER UNIT 65m
SAFE DISTANCE FOR STANDARD COMPASS
SCANNER UNIT 2.4m
DISPLAY UNIT 4.0m
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.5 JMA-9122-6XAH TYPE RADAR
11 －5
11
11.5 JMA-9122-6XAH TYPE RADAR
GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70℃)
Other Unit -15 to +55℃
Relative humidity 93% at +40℃
Vibration 2 to 13.2Hz Amplitude +/-1mm +/-10%
13.2 to 100Hz Acceleration 7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.350VA typical
Approx. 1000VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-2254-6HS)
See 11.11
DISPLAY UNIT (NCD-4990)
See 11.17
PERFORMANCE MONITOR (NJU-85)
See 11.21
AC-DC CONVERTER (NBA-5135)
See 11.22
OPTION
Scanner with Deicing Heater None
Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length
SCANNER UNIT to
TRANSMITTER RECEIVER UNIT 65m
SAFE DISTANCE FOR STANDARD COMPASS
SCANNER UNIT 2.4m
DISPLAY UNIT 4.0m
11 －6
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.6 JMA-9110-6XA TYPE RADAR
11.6 JMA-9110-6XA TYPE RADAR
GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70℃)
Other Unit -15 to +55℃
Relative humidity 93% at +40℃
Vibration 2 to 13.2Hz Amplitude +/-1mm +/-10%
13.2 to 100Hz Acceleration 7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.350VA typical
Approx. 1000VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-2103-6)
See 11.13
DISPLAY UNIT (NCD-4990)
See 11.17
PERFORMANCE MONITOR
(NJU-85)
See 11.21
AC-DC CONVERTER (NBA-
5135)
See 11.22
OPTION
Scanner with Deicing Heater None
Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length
SCANNER UNIT to
TRANSMITTER RECEIVER UNIT 65m
SAFE DISTANCE FOR
STANDARD COMPASS
SCANNER UNIT 2.4m
DISPLAY UNIT 4.0m
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.7 JMA-9110-6XAH TYPE RADAR
11 －7
11
11.7 JMA-9110-6XAH TYPE RADAR
GENERAL SPECIFICATION
Class of emission P0N
Display Color Raster Scan
Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm)
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Resolution less than 30m
Minimum Detection Range less than 40m
Bearing Accuracy less than 1°
Bearing Indication Relative motion mode : N-UP, C-UP and H-UP
True motion mode : N-UP and C-UP
Ambient Condition Temperature
SCANNER UNIT -25 to +55℃ (Storage -25 to +70℃)
Other Unit -15 to +55℃
Relative humidity 93% at +40℃
Vibration 2 to 13.2Hz Amplitude +/-1mm +/-10%
13.2 to 100Hz Acceleration 7m/s2
Power Supply Input AC100 to 115V, 50/60Hz, 1φ or
AC220 to 240V, 50/60Hz, 1φ
Power Consumption Approx.350VA typical
Approx. 1000VA at Maximum wind speed
PS Voltage Fluctuation +/-10% (at the maximum cable length)
Pre Heating Time Within 4 minute
From STBY to TX Within 5 sec.
SCANNER UNIT (NKE-2103-6HS)
See 11.14
DISPLAY UNIT (NCD-4990)
See 11.17
PERFORMANCE MONITOR (NJU-85)
See 11.21
AC-DC CONVERTER (NBA-5135)
See 11.22
OPTION
Scanner with Deicing Heater None
Radar Inter switch NQE-3141-2A (Maximum 2 Radars)
NQE-3141-4A (Maximum 4 Radars)
DISPLAY UNIT (Desktop type) NCD-4990T
Maximum Cable Length
SCANNER UNIT～DISPLAY
UNIT 65m
SAFE DISTANCE FOR STANDARD COMPASS
SCANNER UNIT 2.4m
DISPLAY UNIT 4.0m
11 －8
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.8 SCANNER UNIT (NKE-1139)
11.8 SCANNER UNIT (NKE-1139)
SCANNER UNIT NKE-1139
Dimension Height 791 x Swing Circle 4000 (mm)
Mass Approx.150kg
Polarization Horizontal
Directional Characteristics Horizontal beam width
Vertical beam width
Side lobe Level
: 1.9°
: 25°
: below -26dB (within +/-10°)
: below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor AC100 - 115V、50/60Hz、1φ or
AC220 - 240V、50/60Hz、1φ
Maximum Wind Velocity 51.5m/s (100knots)
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.9 SCANNER UNIT (NKE-1130)
11 －9
11
11.9 SCANNER UNIT (NKE-1130)
SCANNER UNIT NKE-1130
Dimension Height 791 x Swing Circle 4000 (mm)
Mass Approx.180kg
Polarization Horizontal
Directional Characteristics Horizontal beam width
Vertical beam width
Side lobe Level
: 1.9°
: 25°
: below -26dB (within +/-10°)
: below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor AC100 - 115V、50/60Hz、1φ or
AC220 - 240V、50/60Hz、1φ
Maximum Wind Velocity 51.5m/s (100knots)
Transmitting Frequency 3050±20MHz
Transmitting Power 30kW
Transmitting Tube Magnetron[M1555]
TX Pulse width / Repetition
Frequency SP1：0.07μs/2250Hz
MP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2/MP3
3NM ：MP1/MP2/MP3/LP1
6NM ：MP1/MP2/MP3/LP1/LP2
12NM ：MP1/MP2/MP3/LP1/LP2
24NM ：MP3/LP1/LP2
48NM ：LP2
96NM ：LP3
Modulator Solid State Modulator Circuit
Duplexer Circulator + Diode Limiter
Front End Module Built-in
Intermediate Frequency Amplifier Intermediate Frequency
Band Width
Gain
Amplifying Characteristics
: 60MHz
: 25/8/3MHz
: more than 90dB
: Logarithmic Amplifier
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO
11 －10
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.10 SCANNER UNIT (NKE-1129-7/9)
11.10 SCANNER UNIT (NKE-1129-7/9)
SCANNER UNIT NKE-1129-7/9
Dimension 7ft Height 536 x Swing Circle 2270 (mm)
9ft Height 536 x Swing Circle 2825 (mm)
Mass 7ft Approx.51kg
9ft Approx.53kg
Polarization Horizontal
Directional Characteristics Horizontal beam width
Vertical beam width
Side lobe Level
: 1.0° (7ft)
: 0.8° (9ft)
: 20°
: below -26dB (within +/-10°)
: below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor AC100 - 115V、50/60Hz、1φ or
AC220 - 240V、50/60Hz、1φ
Maximum Wind Velocity 51.5m/s (100knots)
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.11 SCANNER UNIT (NKE-1125-6/9)
11 －11
11
11.11 SCANNER UNIT (NKE-1125-6/9)
SCANNER UNIT NKE-1125-6/9
Dimension 6ft Height 536 x Swing Circle 1910 (mm)
9ft Height 536 x Swing Circle 2825 (mm)
Mass 6ft Approx. 55kg
9ft Approx. 60kg
Polarization Horizontal
Directional Characteristics Horizontal beam width
Vertical beam width
Side lobe Level
: 1.2° (6ft)
: 0.8° (9ft)
: 20°
: below -26dB (within +/-10°)
: below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor AC100 - 115V、50/60Hz、1φ or
AC220 - 240V、50/60Hz、1φ
Maximum Wind Velocity 51.5m/s (100knots)
Transmitting Frequency 9410±30MHz
Transmitting Power 25kW
Transmitting Tube Magnetron[M1568BS]
TX Pulse width / Repetition
Frequency SP1：0.07μs/2250Hz
MP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2/MP3
3NM ：MP1/MP2/MP3/LP1
6NM ：MP1/MP2/MP3/LP1/LP2
12NM ：MP1/MP2/MP3/LP1/LP2
24NM ：MP3/LP1/LP2
48NM ：LP2
96NM ：LP3
Modulator Solid State Modulator Circuit
Duplexer Circulator + Diode Limiter
Front End Module Built-in
Intermediate Frequency Amplifier Intermediate Frequency
Band Width
Gain
Amplifying Characteristics
: 60MHz
: 25/8/3MHz
: more than 90dB
: Logarithmic Amplifier
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO
11 －12
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.12 SCANNER UNIT (NKE-2254-6HS)
11.12 SCANNER UNIT (NKE-2254-6HS)
SCANNER UNIT NKE-2254-6HS
Dimension Height 536 x Swing Circle 1910 (mm)
Mass Approx. 55kg
Polarization Horizontal
Directional Characteristics Horizontal beam width
Vertical beam width
Side lobe Level
: 1.2°
: 20°
: below -26dB (within +/-10°)
: below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor DC24V
Maximum Wind Velocity 51.5m/s (100knots)
Transmitting Frequency 9410±30MHz
Transmitting Power 25kW
Transmitting Tube Magnetron[M1568BS]
TX Pulse width / Repetition
Frequency SP1：0.07μs/2250Hz
MP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2/MP3
3NM ：MP1/MP2/MP3/LP1
6NM ：MP1/MP2/MP3/LP1/LP2
12NM ：MP1/MP2/MP3/LP1/LP2
24NM ：MP3/LP1/LP2
48NM ：LP2
96NM ：LP3
Modulator Solid State Modulator Circuit
Duplexer Circulator + Diode Limiter
Front End Module Built-in
Intermediate Frequency Amplifier Intermediate Frequency
Band Width
Gain
Amplifying Characteristics
: 60MHz
: 25/8/3MHz
: more than 90dB
: Logarithmic Amplifier
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.13 SCANNER UNIT (NKE-2103-6)
11 －13
11
11.13 SCANNER UNIT (NKE-2103-6)
SCANNER UNIT NKE-2103-6HS
Dimension Height 458 x Swing Circle 1910 (mm)
Mass Approx. 40kg
Polarization Horizontal
Directional Characteristics Horizontal beam width
Vertical beam width
Side lobe Level
: 1.2°
: 20°
: below -26dB (within +/-10°)
: below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor DC24V
Maximum Wind Velocity 51.5m/s (100knots)
Transmitting Frequency 9410±30MHz
Transmitting Power 10kW
Transmitting Tube Magnetron[MAF1565N]
TX Pulse width / Repetition
Frequency SP1：0.08μs/2250Hz
MP1：0.25μs/1700Hz MP2：0.5μs/1200Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2
3NM ：MP1/MP2LP1
6NM ：MP1/MP2/LP1/LP2
12NM ：MP1/MP2/LP1/LP2
24NM ：MP2/LP1/LP2
48NM ：LP2
96NM ：LP2
Modulator Solid State Modulator Circuit
Duplexer Circulator + Diode Limiter
Front End Module Built-in
Intermediate Frequency Amplifier Intermediate Frequency
Band Width
Gain
Amplifying Characteristics
: 60MHz
: 20/6/3MHz
: more than 90dB
: Logarithmic Amplifier
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO
11 －14
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.14 SCANNER UNIT (NKE-2103-6HS)
11.14 SCANNER UNIT (NKE-2103-6HS)
SCANNER UNIT NKE-2103-6HS
Dimension Height 458 x Swing Circle 1910 (mm)
Mass Approx. 40kg
Polarization Horizontal
Directional Characteristics Horizontal beam width
Vertical beam width
Side lobe Level
: 1.2°
: 20°
: below -26dB (within +/-10°)
: below -30dB (outside +/-10°)
Revolution Approx.24rpm
Power Supply for Motor DC24V
Maximum Wind Velocity 51.5m/s (100knots)
Transmitting Frequency 9410±30MHz
Transmitting Power 10kW
Transmitting Tube Magnetron[MAF1565N]
TX Pulse width / Repetition
Frequency SP1：0.08μs/2250Hz
MP1：0.25μs/1700Hz MP2：0.5μs/1200Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2
3NM ：MP1/MP2LP1
6NM ：MP1/MP2/LP1/LP2
12NM ：MP1/MP2/LP1/LP2
24NM ：MP2/LP1/LP2
48NM ：LP2
96NM ：LP2
Modulator Solid State Modulator Circuit
Duplexer Circulator + Diode Limiter
Front End Module Built-in
Intermediate Frequency Amplifier Intermediate Frequency
Band Width
Gain
Amplifying Characteristics
: 60MHz
: 20/6/3MHz
: more than 90dB
: Logarithmic Amplifier
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.15 TRANSMITTER RECEIVER UNIT (NTG-3230)
11 －15
11
11.15 TRANSMITTER RECEIVER UNIT
(NTG-3230)
SCANNER UNIT NTG-3230
Dimension :Width 615 x Depth 365 x Height 615 (mm)
構造 Wall Mount, Drip Proof
Mass Approx.33kg
Transmitting Frequency 3050±20MHz
Transmitting Power 30kW
Transmitting Tube Magnetron [M1555]
TX Pulse width / Repetition
Frequency SP1：0.07μs/2250Hz
MP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2/MP3
3NM ：MP1/MP2/MP3/LP1
6NM ：MP1/MP2/MP3/LP1/LP2
12NM ：MP1/MP2/MP3/LP1/LP2
24NM ：MP3/LP1/LP2
48NM ：LP2
96NM ：LP3
Modulator Solid State Modulator Circuit
Duplexer Circulator + TRHPL
Front End Module Built-in
Intermediate Frequency Amplifier Intermediate Frequency
Band Width
Gain
Amplifying Characteristics
: 60MHz
: 25/8/3MHz
: more than 90dB
: Logarithmic Amplifier
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO
11 －16
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.16 TRANSMITTER RECEIVER UNIT (NTG-3225)
11.16 TRANSMITTER RECEIVER UNIT
(NTG-3225)
SCANNER UNIT NTG-3225
Dimension :Width 460 x Depth 227 x Height 461 (mm)
構造 Wall Mount, Drip Proof
Mass Approx.15kg
Transmitting Frequency 9410±30MHz
Transmitting Power 25kW
Transmitting Tube Magnetron[M1568BS]
TX Pulse width / Repetition
Frequency SP1：0.07μs/2250Hz
MP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz
LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.2μs/510Hz
0.125、0.25、0.5NM ：SP1
0.75NM ：SP1/MP1
1.5NM ：SP1/MP1/MP2/MP3
3NM ：MP1/MP2/MP3/LP1
6NM ：MP1/MP2/MP3/LP1/LP2
12NM ：MP1/MP2/MP3/LP1/LP2
24NM ：MP3/LP1/LP2
48NM ：LP2
96NM ：LP3
Modulator Solid State Modulator Circuit
Duplexer Circulator + Diode Limiter
Front End Module Built-in
Intermediate Frequency Amplifier Intermediate Frequency
Band Width
Gain
Amplifying Characteristics
: 60MHz
: 25/8/3MHz
: more than 90dB
: Logarithmic Amplifier
Overall Noise Figure 7.5dB ( Typical)
Tuning Manual/AUTO
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.17 DISPLAY UNIT (NCD-4990)
11 －17
11
11.17 DISPLAY UNIT (NCD-4990)
DISPLAY UNIT NCD-4990
Dimension Width 700 x Depth 850 x Height 1100 (mm)
Structure Self-Standing, Drip Proof
Mass Approx.130kg
Screen 23.1inch Color LCD (Effective Diameter, more than 320mm)
Viewing Distance 1m from the center of Display
Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM
Range Marker 0.025, 0.05, 0.1, 0.25, 0.5, 1, 2, 4, 8, 16NM
Range Accuracyr Less than 1% of the Range Scale in use, or 30m whichever is larger
Variable Range Marker 2 (VRM1/VRM2)
VRM Scale 0.000 to 100.0nm, Numerical Indication in 4 digits
Bearing Scale 360° in 1° step
Off Center Within 66% of Radius, except 96nm range
Trackball Cursor Built-in (Target Range, Relative/True bearing Presentation)
Electronic Bearing Lines 2 (EBL1/EBL2) (on Center/Floating)
EBLBearing Indication 000.0° to 359.9°Numerical Indication in 4 digits
Tuning Indication Bar graph
Marking Function Electronic Mark (Maximum 20 points)
Heading Line Indication Electronic
True Motion Unit Built in (0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24 and 48nm)
Anti Sea Clutter (SEA) Manual/AUTO
Anti Rain Clutter (SEA) Manual/AUTO
Display mode North-up / Head-up / Course-up
Trails Indication Off/0.25/0.5/1/3/6/10/15min and Continues
Video Process (PROC) Built in (Scan correlation / Remain)
Interference Rejection (IR) Built in ( Off / Low / Middle / High)
Auto-acquisition Zone (AZ) Sector (2)
User MapiBuilt in, Mark and Line (20,000 points)
Self diagnostic function Built in
Own Ship's Track IndicationiBuilt in
Parallel Index Line (PI) Built in
AIS Indication Built in Display
Activate 300
100
Association function:Built in
Interfacing Slave Display (TRG, VD, BP, BZ)
GPS IEC61162-1(NMEA0183)
LOG
GYRO
AIS IEC61162-2
Inter Switch (OPTION)
Radar Buoy
External Alarm output
Receivable Signal
11 －18
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.17 DISPLAY UNIT (NCD-4990)
Receive capability
Port: NAV1/ALM/ARPA/JARPA at terminal board TB4501
COM port (D-Sub 9 PIN)
Navigation equipment
IEC61162-1/2 Longitude/Latitude GGA>RMC>RMA>GNS>GLL
Waypoint RMB>BWC(BWR)
COG/SOG RMC＞RMA＞VTG
SPEED VBW
Day/Time information ZDA
Alarm acknowledge ACK
Rate of Turn ROT
Rudder RSA
Bearing signal GYRO-SYNC 360x, 180x, 90x, 36x(GYRO I/F)
GYRO-STEP 360x, 180x, 90x, 36x(GYRO I/F)
IEC61162-2 38400bps THS>HDT over 40Hz
(HDG port at terminal board TB4501)
IEC61162-1ii HDT>HDG>HDM>VHW
(HDG port at terminal board TB4501)
Speed signal LOG-SYNC 360x, 180x, 90x, 30x(GYRO I/F)
LOG-PULSE 800, 400, 200, 100(GYRO I/F)
External event mark Contact input (EVENT port at terminal board TB4601)
Radar buoy Negative input (RBVD port at terminal board TB4401)
Depth IEC61162-1/JRC DPT>DBS>DBT>DBK,
JRC format
Water temperature IEC61162-1/JRC MTW, JRC format
Tendency IEC61162-1/JRC CUR, JRC format
Wind IEC61162-1 MWV>MWD
AIS IEC61162-2 VDM,VDO (AIS port at terminal
board TB 4601 )
Acknowledge Contact input (SYSACK, ARPAACK, PWRACK port
at terminal board TB4601)
Sendable Signal
Slave video Radar video: TIY, VD, BP(2048p), BZ
(Terminal board TB4401)
Send capability
Port NAV1, NAV2, ALM, ARPA, JARPA port
at terminal board TB4303. COM port (D-Sub 9 PIN)
Navigation information
IEC61162-1/2 Radar system data RSD
Own ship data OSD
Tracking target data TTM,TLL,TTD,TLB,JRC-ARPA
AIS target data TTM,TLL,TTD,TLB
Alarm ALR
Auto pilot APB
Bearing of destination BOD
Latitude/Longitude data GGA,GLL,RMC
Waypoint RMB,BWC
COG/SOG VTG
Cross track error XTE
Heading data HDT,THS
External alarm Default setting normally closed contact
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.17 DISPLAY UNIT (NCD-4990)
11 －19
11
Maximum current 200mA (SYSALM, ALPAALM, PWRALM
port at terminal board TB4601)
Acknowledge Contact output (ACKOUT port at terminal board TB4401)
Watchman reset Contact output (WMRST port at terminal board TB4401)
Remote maintenance JRC format (MNT port at terminal board TB4601)
AIS alarm acknowledge ACK (AIS port at terminal board TB4601)
External monitor Multi scan monitor Analog RGB, HD15pin Connector 2 port
i. Only with Navigation Equipment is connected.
The Speed measuring accuracy of speed sensor shall confirm to IMO Resolution MSC.96(72).
The measuring accuracy of GPS shall confirm to IMO Resolution MSC.112(73).
ii. Can't be use for target tracking.
11 －20
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.18 Target Tracking Function
11.18 Target Tracking Function
Target Tracking
Function
Available range scale All range
Acquisition Acquisition mode Manual/AUTO（AUTO mode uses Auto-acquisition Zone）
Manual Cancellation Any one Target or All targets at once
Tracking Number of Target 100 Targets (AUTO Tracking)
Maximum tracking range 32nm (Available all range scale)
Presentation Display mode TM (True Motion) / RM (Relative Motion)
Azimuth mode North-up / Head-up / Course-up
Vector mode True/Relative Display
Vector Length Variable, 1 to 60 min. (1min. step)
Past Position True/Relative Display
Number of Dots…10 points
Display Interval Time…0.5 / 1 / 2/ 4 min
Time to Display Vector Within 1min
Time to Stabilize Vector Within 3min
Alarm Auto-acquisition Zone 2 (sector)
Setting Range AZ1 (0.5～32NM),AZ2 (0.5～32NM)
Alarm Indication Symbol on Display, Visible / Audible Alarm
Safe Limits Setting Condition CPA LIMIT 0.1 to 9.9NM
（CPA／TCPA）TCPA LIMIT 1 to 99 minute
Setting Condition Safe Target CPA＞CPA LIMIT
0＞TCPA
TCPA＞TCPA LIMIT
Danger Target CPA≦CPA LIMIT
0≦TCPA≦TCPA LIMIT
Alarm Indication Status Symbol Alarm Audible
Safe Target 〇(wht) OFF OFF
Danger Target ○(red) CPA/TCPA ON
Lost Target Symbol on Display
Visible / Audible Alarm
Data Indication Target Data Simultaneous and Continuous Display for 4 Targets
True Bearing, Range, True Course, True Speed,CPA,TCPA,BCR,BCT
Own Ship's Data Course and Speed
Trial Maneuver Manual Setting
Trial Course 0°to 359.9°
Trial Speed 0 to 100 kn
Accuracy of Display Complied with IMO Requirement
System Failure Alarm Visible / Audible Alarm
Speed Input Manual/AUTO (LOG)
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.19 AIS FUNCTION
11 －21
11
11.19 AIS FUNCTION
AIS機能
Available range scale All range
Activation Activation mode Manual/AUTO（AUTO mode uses Auto-activation Zone）
Manual Cancellation Any one Target
Presentation Number of Activated Target 100 Targets
Number of Target 300 Targets (sleeping target and activated target)
Past Position True/Relative Display
Number of Dots…10 points
Display Interval Time…0.5 / 1 / 2/ 4 min
Display Interval distance…0.1 / 0.2 / 0.5/ 1 NM
Message Broadcast Message, Addressed Message
Display mode TM (True Motion) / RM (Relative Motion)
Azimuth mode North-up / Head-up / Course-up
Vector mode True/Relative Display
Vector Length Variable, 1 to 60 min. (1min. step)
Alarm Auto-activation Zone 2 (Sector)
Setting Range AZ1(0.5 to 32nm), AZ2(0.5 to 32nm)
Alarm Indication Symbol on Display, Visible / Audible Alarm
Safe Limits Setting Condition CPA LIMIT 0.1 to 9.9NM
（CPA／TCPA）TCPA LIMIT 1 to 99min
Alarm Condition Safe Target CPA＞CPA LIMIT
0＞TCPA
TCPA＞TCPA LIMIT
Danger Target CPA≦CPA LIMIT
0≦TCPA≦TCPA LIMIT
Alarm Indication Status Symbol Alarm Audible
Safe Target △(wht) OFF OFF
Danger Target △(red) CPA/TCPA ON
Lost Target Symbol on Display
Visible / Audible Alarm
Data Indication Target Data Simultaneous and Continuous Display for 2 Targets
simple display Ship's Name, Call Sign, MMSI, Course, Speed,
CPA and TCPA
detail display Ship's Name, Call Sign, MMSI, Course, Speed, CPA,
TCPA, Bearing, Range, Ship's Heading Bearing,
Rate of Turn, Latitude, Longitude, Destination
and Navigation Status
Own Ship's Data The ship's name, call sign, MMSI, course, speed,
ship's heading bearing, rate of turn, latitude,
longitude, destination and navigation status of own ship
Trial Maneuver Manual Setting
Trial Course 0° to 360°
Trial Speed 0 to 100 kn
11 －22
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.20 PERFORMANCE MONITOR (NJU-84)
11.20 PERFORMANCE MONITOR (NJU-84)
11.21 PERFORMANCE MONITOR (NJU-85)
11.22 AC-DC CONVERTER (NBA-5135)
Accuracy of Display Complied with IMO Requirement
System Failure Alarm Visible / Audible Alarm
Speed Input Auto (LOG)
PERFORMANCE MONITORNJU-84
Dimension Width 130 x Depth 180 x Height 70 (mm)
Mass Approx.0.7kg
Operating Frequency 3050±30MHz
PERFORMANCE MONITORNJU-85
Dimension Width 130 x Depth 149 x Height 70 (mm)
Mass Approx.0.7kg
Operating Frequency 9410±30MHz
AC-DC CONVERTERNBA-5135
Dimension Width 315 x Depth 385 x Height 99 (mm)
Mass Approx.5kg
Power supply Input AC100 to 240V, 50/60Hz, 1φ
Output Voltage DC24V +/-5%
Output Current 12A max
NQE-3141 Interswitch Unit
A.1 OVERVIEW ............................................................................................A-1
A.1.1 Overview .........................................................................................A-1
A.1.2 Interswitch Setup ...........................................................................A-1
A.2 INTERSWITCH OPERATION ................................................................A-3
A.2.1 Operation Flow ...............................................................................A-3
A.2.2 Inter Switch Menu ...........................................................................A-4
A.2.3 Change of Connection Pattern (with 2 Display Units) ................A-6
A.2.4 Change of Connection Pattern (with 3 or More Display Units) ..A-7
A.2.5 Operating Connection Pattern Files (File Operations) ...............A-8
A.2.6 Names of Display Units and Scanner Units .................................A-9
A.3 REFERENCE .......................................................................................A-10
A.3.1 Preheat Time after Change of Connection Pattern ...................A-10
A.3.2 Notes on Changing Connection Pattern ....................................A-10
A.3.3 Notes on Connecting Slave Display Unit ...................................A-10
A.3.4 Setting at Installation ...................................................................A-11
Appendix A
NQE-3141 Interswitch Unit
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.1 OVERVIEW
A－1
A
A.1 OVERVIEW
A.1.1 Overview
Interswitch NQE-3141 is equipment that enables free changeover between radar
display units installed on the bridge and antenna units having different
characteristics.
If display unit is turned off or malfunctioned, the scanner unit can be controlled by
other display unit.
If interswitch unit had malfunctioned, the radar system is switched to standalone
mode.
Up to 8 units can be changed over.
When the connected scanner is changed, following setting values are
automatically loaded.
A.1.2 Interswitch Setup
Connection modes can be changed simply by changing the interswitch connection
(upper left of the display).
Tune Adjustment Section 7.1.3 "Tuning (Tune Adjustment)"
Bearing Adjustment Section 7.1.4 "Bearing Adjustment"
Range Adjustment Section 7.1.5 "Range Adjustment"
Antenna Height Section 7.1.8 "Antenna Height Setting (Antenna
Height)"
Antenna installation location Section 7.1.9 "Setting of CCRP (CCRP Setting)"
Sector Blank Section 7.2.2 "Sector Blank Setting (Sector Blank)"
TNI Blank Section 7.2.3 "TNI Blank Setting (TNI Blank)"
Performance monitor
adjustment Section 7.3.4 "Adjustment of Performance Monitor"
PRF Fine Tuning Section 3.8.3 "Set Scanner Unit (TXRX Setting)"
A master display unit is always necessary for establishing a slave
connection.
Before a slave display unit can be placed in transmission state, the
master display unit must be placed in transmission state.
i
A－2
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.1 OVERVIEW
upper left of the display
The upper stand indicates the number of the connected scanner unit.
The lower stand indicates the connection mode.
:Mode in which the scanner unit can be controlled by the
display unit
:Mode in which the scanner unit cannot be controlledi
i. When Slave is selected, transmission / standby and pulse length cannot be changed.
The available range is also limited.
Connection Switch
Connected
Scanner
Unit
Connection
Mode
Master
Slave
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION
A－3
A
A.2 INTERSWITCH OPERATION
Follow the flowchart below to change the current interswitch connection pattern.
A.2.1 Operation Flow
Close the Inter Switch Menu .
Change the connection pattern .
Place the transmission standby state .
Open the Inter Switch Menu .
A－4
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION
A.2.2 Inter Switch Menu
The Inter Switch Menu can be opened only when the transmission standby state.
Procedures
1) Press the [TX/STBY] key to stop transmitting.
The transmission standby state will be placed.
2) Move the cursor onto the Interswitch connection change (upper
left of the display), and left-click.
The Inter Switch Menu will appear.
Exit
1) Left-click the button.
The Inter Switch Menu will close.
Inter Switch Menu (with 2 Display Units)
0.Exit
b. Set c.Exit
Current
connection
status
a. Connection
pattern
Display unit
in operation
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION
A－5
A
a. Connection pattern
If this button is clicked, the connection pattern is selected.
The display unit in operation is enclosed in a square □.
The background of the current connection pattern display is highlighted.
b. Set
If this button is clicked, the change of connection is determined.
c. Exit
If this button is clicked, the Inter Switch Menu is closed .
Inter Switch Menu (with 3 or More Display Units)
a. Connected scanner unit
In mode for naming a display unit or antenna unit, clicking on a unit opens the name input
window.
If only 2 display units are installed but the interswitch is set for 3
or more display units, the Inter Switch Menu for 3 or more
display units will appear.
i
b. Display unit
connected as
master
d. Name
e. File
Operations
c. Display unit
connected as
slave
f. Set
g. Exit
a. Connected
scanner unit
A－6
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION
b. Display unit connected as master
c. Display unit connected as slave
If this button is clicked, select / cancel the display unit.
If this button is clicked in the naming a display unit or scanner unit mode , the name input
window is opened .
d. Name
If this button is clicked, set to the display or scanner unit rename mode.
e. File Operations
If this button is clicked, the File Operations menu is opened.。
f. Set
If this button is clicked, the change of connection is determined.
g. Exit
If this button is clicked, the Inter Switch Menu is closed .
A.2.3 Change of Connection Pattern (with 2 Display Units)
If two display units are installed, a connection pattern needs to be selected.
Procedures
1) Open the Inter Switch menu (with 2 Display Units).
2) Move the cursor onto the Connection pattern (see Section A.2.2 "Inter
Switch Menu" and Section a. "Connection pattern") to be changed , and left-click.
The connection pattern will be selected, and (Section b. "Set") will blink.
3) Left-click the button.
The connection pattern will be changed.
3. Set
3. Set
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION
A－7
A
A.2.4 Change of Connection Pattern (with 3 or More Display
Units)
If three or more display units are installed, the layout of connection patterns needs
to be set.
Procedures
1) Open the Inter Switch Menu (with 3 or More Display Units).
2) Move the cursor onto the display unit (Section b. "Display unit connected as
master" or Section c. "Display unit connected as slave") to be changed , and left-
click.
The selected display unit will be highlighted.
To deselect the display unit, left-click key again.
3) Move the cursor to the change-destination display unit, and left-
click.
he selected display unit in step 2 will be switched to the change-destination display unit, and
(Section f. "Set") will blink.
If the change destination is empty, control will move and will blink.
4) Left-click the button.
The connection pattern will be changed.
A master display unit is always necessary for establishing a
slave connection.
3. Set
3. Set
3. Set
i
A－8
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION
A.2.5 Operating Connection Pattern Files (File Operations)
Frequently used connection patterns can be read easily by saving interswitch
connection patterns.
[1] Loading connection patterns (Load)
Procedures
1) Open the Inter Switch Menu (with 3 or More Display Units).
2) Left-click the button.
The File Operations menu will appear.
3) Left-click the button.
Currently saved connection patterns in memory will be listed.
4) Left-click the button corresponding to the file to be loaded.
Confirmation Window will appear.
5) Left-click the to load.
The connection pattern will be changed.
[2] Saving connection patterns (Save)
Procedures
1) Open the Inter Switch Menu (with 3 or More Display Units).
2) Left-click the button.
The File Operations window will appear.
3) Left-click the button.
The Save menu will appear.
Currently saved connection patterns in memory will be listed.
4) Left-click the button corresponding to the file to be saved.
The Input File Name window will appear.
5) Enter the file name to be saved.
Up to 8 characters can be entered.For the input method on the character input screen, see
Section 3.3.4.7 "Entering a character".
The connection pattern will be saved when the name is input.
2. File Operation
3. Load
1. Yes
2. File Operation
2. Save
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION
A－9
A
[3] Erasing a connection pattern (Erase)
Procedures
1) Open the Inter Switch Menu (with 3 or More Display Units).
2) Left-click the button.
The File Operations window will appear.
3) Left-click the button.
The Erase menu will appear.
The list of connection patterns stored in the memory will be displayed.
4) Left-click the button corresponding to the file to be erased.
Confirmation Window will appear.
5) Left-click the to load.
The selected connection pattern is erased and the file name is deleted from the list.
A.2.6 Names of Display Units and Scanner Units
The display units and antenna units can be named.
Procedures
1) Open the Inter Switch Menu (with 3 or More Display Units).
2) Left-click the button.
"Name" will be highlighted, indicating that the rename mode is activated.
3) Move the cursor to the display unit (Section b. "Display unit connected as
master" or Section c. "Display unit connected as slave") or scanner unit (Section a.
"Connected scanner unit") to be renamed , and left-click.
he Input IND Name or the Input TXRX Name window will appear.
4) Input a new unit name.
Up to 8 characters can be input as a unit name. For the input method on the character input
menu, see Section 3.3.4.7 "Entering a character".
The selected display unit or antenna unit will be renamed when the new name is input.
2. File Operation
3. Erase
1. Yes
1. Name
A－10
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.3 REFERENCE
A.3 REFERENCE
A.3.1 Preheat Time after Change of Connection Pattern
After the current interswitch connection pattern has been changed, operation
needs to wait until the system is ready. This is because the preheat time varies
depending on the previous connection of the scanner unit and display unit.
The wait time is necessary for protecting the electronic tubes that emit radio
waves.
A.3.2 Notes on Changing Connection Pattern
An attempt to change to another connection pattern immediately after the
completion of connection pattern change may fail.
This is because internal processing still needs some preparation time upon
completion of connection pattern change. Let several seconds pass between
connection pattern change operations.
A.3.3 Notes on Connecting Slave Display Unit
Before a slave display unit can be placed in transmission state, the master display
unit must be placed in transmission state. If the master display unit is moved from
the transmission state to the transmission standby state, the slave display unit is
forcibly placed in transmission standby state. When they are in transmission
standby state, is shown in the alarm indication (lower right of the
display), and the alarm sounds.
A slave display unit cannot control tune. Tune is controlled by the master display
unit. is shown in the transmitter pulse length (upper left of the display).
Range change for a slave display unit is limited by the range and pulse length /
repetition frequency of the master display unit. As a rule, a greater range than the
range of the master display unit cannot be set for a slave display unit. However, if
the transmitter pulse length of a slave display unit is identical to the master
display unit's and the repetition frequency is within the master display unit's, a
greater range than the master display unit's can be selected for the slave display
unit. When the master display unit narrows the range or changes the transmitter
a) When not changed to a new connection pattern Preheating not
required
b) When changed to a new connection pattern and an
scanner unit had been used before the change Preheating not
required
c) When changed to a new connection pattern and an
scanner unit had not been used before the change Preheating
required
TXRX Standby
Slave
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.3 REFERENCE
A－11
A
pulse length, the range of the slave display unit may be forcibly changed. In this
case, is shown in the alarm indication (lower right of the
display), and the alarm sounds.
A.3.4 Setting at Installation
Setting of the interswitch circuit (CCL-304*)
The settings of the DIP switches SW11 to SW13 are shown below.
1) SW11 setting (extension mode and master/slave settings)
Master Range CHG
SW 11 SW 13 SW 12
Interswitch circuit PCB
CCL-304*
4Description
Extension mode setting
ON Extension mode
OFF Normal mode
3Description
ON Slave
OFF Master
1, 2 Description
ON Unused
OFF Unused
Unused
Master/slave setting
Set the switch to OFF if the
number of connected display
units is four or less.
Set the switch to ON if the
slave ISW PCB is selected in
extension mode.
Set the switch to OFF in
normal state.
1234
ON
OFF
A－12
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.3 REFERENCE
2) SW12 setting (radar connection settings)
3) SW13 (unused)
Before the DIP switches of the interswitch circuit can be set, the
interswitch breaker must be turned off in order to ensure safety
operation.
1234
ON
OFF
8
Radar connection settings
ON No.8 display unit connected
OFF No.8 display unit not connected
5678
7ON No.7 display unit connected
OFF No.7 display unit not connected
6ON No.6 display unit connected
OFF No.6 display unit not connected
5ON No.5 display unit connected
OFF No.5 display unit not connected
4ON No.4 display unit connected
OFF No.4 display unit not connected
3ON No.3 display unit connected
OFF No.3 display unit not connected
2ON No.2 display unit connected
OFF No.2 display unit not connected
1ON No.1 display unit connected
OFF No.1 display unit not connected
1,2,3,4 Unused (All OFF)
1234
ON
OFF
DRAWINGS
B.1 Interconnection Diagram of Display Unit ...........................................B-1
B.1.1 NCD-4990 ........................................................................................B-2
B.1.2 NCD-4990 w/NBA-5135 ...................................................................B-3
B.1.3 NCD-4990T ......................................................................................B-4
B.1.4 NCD-4990T w/NBA-5135 ................................................................B-5
B.1.5 NWZ-170-R ......................................................................................B-6
B.1.6 NWZ-170-RT ....................................................................................B-7
B.1.7 NCE-5163-R .....................................................................................B-8
B.1.8 NCE-5163-RT ...................................................................................B-9
B.1.9 NBA-5135 ......................................................................................B-10
B.2 Power System Daigram of Display Unit ...........................................B-11
B.3 Signal Flow Diagram of Display Unit ................................................B-12
B.4 Primary Power System Diagram .......................................................B-13
B.5 Block Diagram of Scanner Unit ........................................................B-14
B.5.1 NKE-2103 ......................................................................................B-15
B.5.2 NKE-2254 ......................................................................................B-16
B.5.3 NKE-1125/NKE-1130 .....................................................................B-17
Appendix B
DRAWINGS
B.5.4 NKE-1129, NTG-3225 / NKE-1139, NTG-3230 .............................B-18
B.6 Interconnection Diagram of Scanner Unit .......................................B-19
B.6.1 NKE-2103 ......................................................................................B-20
B.6.2 NKE-2254 ......................................................................................B-21
B.6.3 NKE-1125 (AC110V) ......................................................................B-22
B.6.4 NKE-1125 (AC220V) ......................................................................B-23
B.6.5 NKE-1129 (AC110V) ......................................................................B-24
B.6.6 NKE-1129 (AC220V) ......................................................................B-25
B.6.7 NTG-3225 ......................................................................................B-26
B.6.8 NKE-1130 (AC110V) ......................................................................B-27
B.6.9 NKE-1130 (AC220V) ......................................................................B-28
B.6.10 NKE-1139 (AC110V) ......................................................................B-29
B.6.11 NKE-1139 (AC220V) ......................................................................B-30
B.6.12 NTG-3230 ......................................................................................B-31
B.7 Terminal Board Connection Diagram ...............................................B-32
B.7.1 JMA-9110-6XA/JMA-9110-6XAH ..................................................B-33
B.7.2 JMA-9110-6XA/JMA-9110-6XAH (desktop) .................................B-34
B.7.3 JMA-9122-6XAH ............................................................................B-35
B.7.4 JMA-9122-6XAH (desktop) ...........................................................B-36
B.7.5 JMA-9122-6XA/9XA ......................................................................B-37
B.7.6 JMA-9123-7XA/9XA ......................................................................B-38
B.7.7 JMA-9132-SA ................................................................................B-39
B.7.8 JMA-9133-SA ................................................................................B-40
B.7.9 NCD-4990T ....................................................................................B-41
B.8 GYRO I/F .............................................................................................B-42
B.9 Inter Switch Unit .................................................................................B-44
B.9.1 Terminal Board Connection Diagram .........................................B-44
B.9.2 Interconnection Diagram .............................................................B-46
B－2
JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display Unit
B.1.1 NCD-4990
Fig B-1: Interconnection Diagram of NCD-4990
2P
J4308
26P
J4307
26P
J4306
50P
J4301
18P
J4304
8P
J4305
3P
J4313
3P
J4314
9P
J4309
14P
TB4101
TO TRU
TO ISW
26P
TB4201
TO EXT-RADAR
30P
TB4401
TO SEN SOR
22P
TB4501
TO A LARM SYSTEM
22P
TB4601
TO GYRO
6P
TB4701
TO LOG
12P
TB4801
TO PC
9P
J4310
TERMINAL BOARD
CQD-2097
PC430
50P
J4302
50P
J4303
30P
J4311
TO OPU
30P
J4312
TO SUB OPU
6P
J6411
6P
J6410 6P
J6409
6P
J6408 2P
J6406 7P
J6405 14P
J6404 14P
J6403 15 P
J6402
30P
J6401
OPERATION CIRCUIT D
CCK-976
PC640
14P
J6101 15 P
J6102
OPERATION
CIRCUIT A
CCK-973
PC610
7P
J6201
OPERATION
CIRCUIT B
CCK-974
PC620
SP1
A1
*PS/2 EXTENSION CABLE
(USER SUPPLY )
OPERATION UNIT
NCE-5163-R
2 m H - 7ZC RD 133 7 (N CE- 5 16 3 -R )
JR C SU PPLY
B101
B102
PC900
11P
TB914
15P
TB913
11P
TB912
15P
TB911
2P
TB905
INTERSWITCH UNIT
NQE-3141-2A
CH1
CH2
50P
J4105
50P
J4106
50P
J4107
*OPTION
W401 H-7ZCRD1339
W402 H-7ZCRD1339
W403 H-7ZCRD1339
64P
J4103
64P
J4104
64P
J4102
64P
J4101
64P
J4401 64P
J4402 64P
J1
GYRO INTERFACE
CIRCUIT
CMJ-462E
PC420
RADAR PROCESS
CIRCUIT
CDC-1324
PC440
MOTHERBOARD
CQC-1192
PC410
64P
J4403
64P
J4404
AIS PROCESS
CIRCUIT
CDC-1325
PC460
64P
J4601
64P
J4501
ARPA PROCESS
CIRCUIT
CDC-1186D
PC450
15P
J4409
VGA
15P
J4405
VGA
28P
J4406
DVI-D
8P
J4407
RJ-45
50P
J4408
CF-card
LCD
OPERATION
CIRCUIT
CCK -972 PC710
8P
J711
MONITOR UNIT
NWZ-170-R
LCD PANEL
H-7WSRD0002A
8P
H-7ZCRD1328
9P 2m H-7ZCRD1329A (NWZ-170-R)
DVI 2m H-7ZCRD1345 (NWZ-170-R)
20P
J4108
8P
POWER SUPPLY
CBD-1661
18P
20P
*PS/2 MOUSE/TRKBALL
(USER SUPPLY)
*OPTION
(USER SUPPLY)
2P
2P
AC OUT2
+
ー
U
V
W
BATTERY
IN
AC OUT2
AC IN
U
W
V
U
W
V
4351A07335 FILTER
INOUT
RED
WHT
BLU
RED
WHT
BLU
AC 2m 5ZCGH00285 (NWZ-170-R)
AC100-115V 50/60Hz
AC220-240V 50/60Hz
SCANNER MOTOR
POWER
NCD-4990（自立型） 機内接続図
Interconnection dia
g
ram of DISPLAY UNIT t
yp
e NCD-4990
(
self standin
g)
JMA-9122-6/9XA,JMA-9123-7/9XA,JMA-9132-SA,JMA-9133-SA
RADAR PROCESS UNIT
NDC-1399-9
JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display Unit
B－3
B
B.1.2 NCD-4990 w/NBA-5135
Fig B-2: Interconnection Diagram of NCD-4990 w/NBA-5135
2P
J4308
26P
J4307
26P
J4306
50P
J4301
18P
J4304
8P
J4305
3P
J4313
3P
J4314
9P
J4309
14P
TB4101
TO TRU
TO ISW
26P
TB4201
TO EXT-RADAR
30P
TB4401
TO S ENSOR
22P
TB4501
TO A LARM SYSTEM
22P
TB4601
TO GYRO
6P
TB4701
TO LOG
12P
TB4801
TO PC
9P
J4310
TERMINAL BOARD
CQD-2097
PC430
50P
J4302
50P
J4303
30P
J4311
TO OPU
30P
J4312
TO SUB OPU
6P
J6411
6P
J6410 6P
J6409
6P
J6408 2P
J6406 7P
J6405 14P
J6404 14P
J6403 15P
J6402
30P
J6401
OPERATION CIRCUIT D
CCK-976
PC640
14P
J6101 15P
J6102
OPERATION
CIRCUIT A
CCK-973
PC610
7P
J6201
OPERATION
CIRCUIT B
CCK-974
PC620
SP1
A1
*PS/2 EX TENSION CA BLE
(USER SUPPLY )
OPERATION UNIT
NCE-5163-R
2m H -7ZC RD 1 33 7 (N CE - 5 163 - R )
JRC SU PPLY
B101
B102
PC900
11P
TB914
15P
TB913
11P
TB912
15P
TB911
2P
TB905
INTERSWITCH UNIT
NQE-3141-2A
CH1
CH2
50P
J4105
50P
J4106
50P
J4107
*OPTION
W401 H -7ZCRD1339
W402 H -7ZCRD1339
W403 H -7ZCRD1339
64P
J4103
64P
J4104
64P
J4102
64P
J4101
64P
J4401 64P
J4402 64P
J1
GYRO INTERFACE
CIRCUIT
CMJ-462E
PC420
RADAR PROCESS
CIRCUIT
CDC-1324
PC440
MOTHERBOARD
CQC-1192
PC410
64P
J4403
64P
J4404
AIS PROCESS
CIRCUIT
CDC-1325
PC460
64P
J4601
64P
J4501
ARPA PROCESS
CIRCUIT
CDC-1186D
PC450
15P
J4409
VGA
15P
J4405
VGA
28P
J4406
DVI-D
8P
J4407
RJ-45
50P
J4408
CF-card
LCD
OPERATION
CIRCUIT
CCK -972 PC71 0
8P
J711
MONITOR UNIT
NWZ-170-R
LCD PANEL
H-7WSRD0002A
8P
H-7ZCRD1328
9P 2m H-7ZCRD1329A (NWZ-170-R )
DVI 2m H-7ZCRD1345 (NWZ-170-R)
20P
J4108
8P
POWER SUPPLY
CBD-1661
18P
20P
*PS/2 MOUSE/TRKBALL
(USER SUPPLY)
*OPTION
(USER SUPPLY)
2P
2P
AC OUT2
+
ー
U
V
W
BATTERY
IN
AC OUT2
AC IN
U
W
V
U
W
V
4351A07335 FILTER
INOUT
RED
WHT
BLU
RED
WHT
BLU
AC 2m 5ZCGH00285 (NWZ-170-R)
U V FG
+ーFG
TB522
AC IN
TB521
DC24V OUT
AC/DC
CONVERTER UNIT
NBA-5135
AC100-115V 50/60Hz
AC220-240V 50/60Hz
SCAN NER MOTOR
POWER DC24V
NCD-4990（自立型） 機内接続図
Interconnection diagram of DISPLAY UNIT type NCD-4990(self standing)
JMA-9110-6XA,JMA-9110-6XAH,JMA-9122-6XAH
RADAR PROCESS UNIT
NDC-1399-9
W406 H-7ZCRD1342A
RED
WHT
RED
WHT
B－4
JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display Unit
B.1.3 NCD-4990T
Fig B-3: Interconnection Diagram of NCD-4990T
2P
J4308
26P
J4307
26P
J4306
50P
J4301
18P
J4304
8P
J4305
3P
J4313
3P
J4314
9P
J4309
14P
TB4101
TO TRU
TO ISW
26P
TB4201
TO EXT-RADAR
30P
TB4401
TO S ENSOR
22P
TB4501
TO A LARM SYSTEM
22P
TB4601
TO GYRO
6P
TB4701
TO LOG
12P
TB4801
TO PC
9P
J4310
TERMINAL BOARD
CQD-2097
PC430
50P
J4302
50P
J4303
30P
J4311
TO OPU
30P
J4312
TO SUB OPU
6P
J6411
6P
J6410 6P
J6409
6P
J6408 2P
J6406 7P
J6405 14P
J6404 14P
J6403 15P
J6402
30P
J6401
OPERATION CIRCUIT D
CCK-976
PC640
14P
J6101 15P
J6102
OPERATION
CIRCUIT A
CCK-973
PC610
7P
J6201
OPERATION
CIRCUIT B
CCK-974
PC620
SP1
A1
*PS/2 EX TENSION CA BLE
(USER SUPPLY )
OPERATION UNIT
NCE-5163-RT
5m H -7ZC RD 1 33 8 (N CE - 5 163 - R T)
JRC SU PPLY
B101
B102
PC900
11P
TB914
15P
TB913
11P
TB912
15P
TB911
2P
TB905
INTERSWITCH UNIT
NQE-3141-2A
CH1
CH2
50P
J4105
50P
J4106
50P
J4107
*OPTION
W401 H -7ZCRD1339
W402 H -7ZCRD1339
W403 H -7ZCRD1339
64P
J4103
64P
J4104
64P
J4102
64P
J4101
64P
J4401 64P
J4402 64P
J1
GYRO INTERFACE
CIRCUIT
CMJ-462E
PC420
RADAR PROCESS
CIRCUIT
CDC-1324
PC440
MOTHERBOARD
CQC-1192
PC410
64P
J4403
64P
J4404
AIS PROCESS
CIRCUIT
CDC-1325
PC460
64P
J4601
64P
J4501
ARPA PROCESS
CIRCUIT
CDC-1186D
PC450
15P
J4409
VGA
15P
J4405
VGA
28P
J4406
DVI-D
8P
J4407
RJ-45
50P
J4408
CF-card
LCD
OPERATION
CIRCUIT
CCK -972 PC71 0
8P
J711
MONITOR UNIT
NWZ-170-RT
LCD PANEL
H-7WSRD0002A
8P
H-7ZCRD1328
9P 5m H-7ZCRD1330A (NWZ-170-R T)
DVI 5m H-7ZCRD1346 (NWZ-170-RT)
20P
J4108
8P
POWER SUPPLY
CBD-1661
18P
20P
*PS/2 MOUSE/TRKBALL
(USER SUPPLY)
*OPTION
(USER SUPPLY)
2P
2P
AC OUT2
+
ー
U
V
W
BATTERY
IN
AC OUT2
AC IN
U
W
V
U
W
V
4351A07335 FILTER
INOUT
RED
WHT
BLU
RED
WHT
BLU
AC 5m 5ZCGH00364 (NWZ-170-RT)
AC100-115V 50/60Hz
AC220-240V 50/60Hz
SCANNER MOTOR
POWER
NCD-4990T（卓上型） 機内接続図
Interconnection diagram of DISPLAY UNIT type NCD-4990T(desktop)
RADAR PROCESS UNIT
NDC-1399-9T
1 2 3
1 2 3
RED
BLU
WHT
W405 H-7ZCRD1341A
TB402
JMA-9122-6/9XA,JMA-9123-7/9XA,JMA-9132-SA,JMA-9133-SA
JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display Unit
B－5
B
B.1.4 NCD-4990T w/NBA-5135
Fig B-4: Interconnection Diagram of NCD-4990T w/NBA-5135
2P
J4308
26P
J4307
26P
J4306
50P
J4301
18P
J4304
8P
J4305
3P
J4313
3P
J4314
9P
J4309
14P
TB4101
TO TRU
TO ISW
26P
TB4201
TO EXT-RADAR
30P
TB4401
TO S ENSOR
22P
TB4501
TO A LARM SYSTEM
22P
TB4601
TO GYRO
6P
TB4701
TO LOG
12P
TB4801
TO PC
9P
J4310
TERMINAL BOARD
CQD-2097
PC430
50P
J4302
50P
J4303
30P
J4311
TO OPU
30P
J4312
TO SUB OPU
6P
J6411
6P
J6410 6P
J6409
6P
J6408 2P
J6406 7P
J6405 14P
J6404 14P
J6403 15P
J6402
30P
J6401
OPERATION CIRCUIT D
CCK-976
PC640
14P
J6101 15P
J6102
OPERATION
CIRCUIT A
CCK-973
PC610
7P
J6201
OPERATION
CIRCUIT B
CCK-974
PC620
SP1
A1
*PS/2 EX TENSION CA BLE
(USER SUPPLY )
OPERATION UNIT
NCE-5163-RT
5m H -7ZC RD 1 33 8 (N CE - 5 163 - R T)
JRC SU PPLY
B101
B102
PC900
11P
TB914
15P
TB913
11P
TB912
15P
TB911
2P
TB905
INTERSWITCH UNIT
NQE-3141-2A
CH1
CH2
50P
J4105
50P
J4106
50P
J4107
*OPTION
W401 H -7ZCRD1339
W402 H -7ZCRD1339
W403 H -7ZCRD1339
64P
J4103
64P
J4104
64P
J4102
64P
J4101
64P
J4401 64P
J4402 64P
J1
GYRO INTERFACE
CIRCUIT
CMJ-462E
PC420
RADAR PROCESS
CIRCUIT
CDC-1324
PC440
MOTHERBOARD
CQC-1192
PC410
64P
J4403
64P
J4404
AIS PROCESS
CIRCUIT
CDC-1325
PC460
64P
J4601
64P
J4501
ARPA PROCESS
CIRCUIT
CDC-1186D
PC450
15P
J4409
VGA
15P
J4405
VGA
28P
J4406
DVI-D
8P
J4407
RJ-45
50P
J4408
CF-card
LCD
OPERATION
CIRCUIT
CCK -972 PC71 0
8P
J711
MONITOR UNIT
NWZ-170-RT
LCD PANEL
H-7WSRD0002A
8P
H-7ZCRD1328
9P 5m H-7ZCRD1330A (NWZ-170-R T)
DVI 5m H-7ZCRD1346 (NWZ-170-RT)
20P
J4108
8P
POWER SUPPLY
CBD-1661
18P
20P
*PS/2 MOUSE/TRKBALL
(USER SUPPLY)
*OPTION
(USER SUPPLY)
2P
2P
AC OUT2
+
ー
U
V
W
BATTERY
IN
AC OUT2
AC IN
U
W
V
U
W
V
4351A07335 FILTER
INOUT
RED
WHT
BLU
RED
WHT
BLU
AC 5m 5ZCGH00364 (NWZ-170-RT)
U V FG
+ーFG
TB522
AC IN
TB521
DC24V OUT
AC/DC
CONVERTER UNIT
NBA-5135
AC100-115V 50/60Hz
AC220-240V 50/60Hz
SCAN NER MOTOR
POWER DC24V
NCD-4990T（卓上型） 機内接続図
Interconnection diagram of DISPLAY UNIT type NCD-4990T(desktop)
JMA-9110-6XA,JMA-9110-6XAH,JMA-9122-6XAH
RADAR PROCESS UNIT
NDC-1399-9T
1 2 3
1 2 3
RED
BLU
WHT
W405 H-7ZCRD1341A
TB402
1 2 3
1 2 3
TB401
W408 H-7ZCRD1344A GR N
GR N
W407 H-7ZCRD1343A
WHT
BLK
GRN
WHT
BLK
GRN
B－6
JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display Unit
B.1.5 NWZ-170-R
Fig B-5: Interconnection Diagram of NWZ-170-R
J7101
BRILL
AC 1 0 0V
240V
FAN
ALM
DVIRGB
CCK-972
PC710
H-7WSRD0002A
LCD
8P
H-7ZCRD1328
FL1
9P 2m H-7ZCRD1329A
DVI 2m H-7ZCRD1345
AC 2m VM0301-VM0303B2Mｸﾛ
CDC-1324
J4406
CQD-2097
J4309
CBD-1661
OUTLET
Monitor Unit Interconnection
CML-764-R (NWZ-170-R)
JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display Unit
B－7
B
B.1.6 NWZ-170-RT
Fig B-6: Interconnection Diagram of NWZ-170-RT
J7101
BRILL
AC 1 0 0V
240V
FAN
ALM
DVIRGB
CCK-972
PC710
H-7WSRD0002A
LCD
8P
H-7ZCRD1328
FL1
9P 5m H-7ZCRD1330A
DVI 5m H-7ZCRD1346
AC 5m VM0301-VM0303B5Mｸﾛ
CDC-1324
J4406
CQD-2097
J4309
CBD-1661
OUTLET
Monitor Unit Interconnection
CML-764-RT (NWZ-170-RT)
B－8
JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display Unit
B.1.7 NCE-5163-R
Fig B-7: Interconnection Diagram of NCE-5163-R
6P
J6411
6P
J6410 6P
J6409
6P
J6408 2P
J6406 7P
J6405 14P
J6404 14P
J6403 15P
J6402
30P
J6401
OPERATION CIRCUIT D
CCK-976
PC 640
14P
J6101 15P
J6102
OPERATION
CIRCUIT A
CCK-973
PC610
7P
J6201
OPERATION
CIRCUIT B
CCK-974
PC620
SP1
A1
OPERATION UNIT
NCE-5163-R
W67 2m H-7ZCRD1337
W62 H-7ZCRD1332
W65 H-7ZCRD1335
W63 H-7ZCRD1333A
W64 H-7ZCRD1334
FL1
2P
J6407
Operation Unit Interconnection
CMD-996-R (NCE-5163-R)
JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display Unit
B－9
B
B.1.8 NCE-5163-RT
Fig B-8: Interconnection Diagram of NCE-5163-RT
6P
J6411
6P
J6410 6P
J6409
6P
J6408 2P
J6406 7P
J6405 14P
J6404 14P
J6403 15P
J6402
30P
J6401
OPERATION CIRCUIT D
CCK-976
PC 640
14P
J6101 15P
J6102
OPERATION
CIRCUIT A
CCK-973
PC610
7P
J6201
OPERATION
CIRCUIT B
CCK-974
PC620
SP1
A1
OPERATION UNIT
NCE-5163-RT
W68 5m H-7ZCRD1338
W62 H-7ZCRD1332
W65 H-7ZCRD1335
W63 H-7ZCRD1333A
W64 H-7ZCRD1334
FL1
2P
J6407
Operation Unit Interconnection
CMD-996-RT (NCE-5163-RT)
B－10
JMA-9100 Instruction Manual > B.DRAWINGS > B.1 Interconnection Diagram of Display Unit
B.1.9 NBA-5135
Fig B-9: Interconnection Diagram of NBA-5135
AC/DC Converter Interconnection
CBD-1684A (NBA-5135)
FL1
LF-210
FS1
1 2 3
1 2 3
TB521
123
123
TB522
A1
AES300-24B
UV
W1 H-7ZCRD1495
W2 H-7ZCRD1496
BLK
WHT
RED
Twisted
uvFG
RED WHT
N L
FG
+ + + - - -
RED WHT
BLK
BLK
BLK
BLK
WHTWHT
BLK
WHT
RED
W6 H-7ZCRD1499
W5 H-7ZCRD1499
W4 H-7ZCRD1498
W3 H-7ZCRD1497
Twisted
JMA-9100 Instruction Manual > B.DRAWINGS > B.2 Power System Daigram of Display Unit
B－11
B
B.2 Power System Daigram of Display Unit
Fig B-10: Power System Diagram of NCD-4990/T
2P
J4308
26P
J4307
26P
J4306
50P
J4301
18P
J4304
8P
J4305
3P
J4313
3P
J4314
9P
J4309
14P
TB4101
TO TRU
TO ISW
26P
TB4201
TO EXT-RADAR
30P
TB4401
TO SENSOR
22P
TB4501
TO A LAR M SYSTEM
22P
TB4601
TO GYRO
6P
TB4701
TO LOG
12P
TB4701
TO PC
9P
J4310
TERMINAL BOARD
CQD-2097
PC430
50P
J4302
50P
J4303
30P
J4311
TO OPU
30P
J4312
TO SUB OPU
6P
J6411
6P
J6410 6P
J6409
6P
J6408 2P
J6406 7P
J6405 14P
J6404 14P
J6403 15P
J6402
30P
J6401
OPERATION CIRCUIT D
CCK-976
PC640
14P
J6101 15P
J6102
OPERATION
CIRCUIT A
CCK-973
PC610
7P
J6201
OPERATION
CIRCUIT B
CCK-974
PC620
SP1
A1
*PS/2 EX TENSION CABLE
(USER SU PPLY )
OPERATION UNIT
NCE-5163-R
2m H-7ZCRD1337 (NCE-5163-R)
5m H-7ZCRD1338 (NCE-5163-RT)
JRC SUPPLY
B101
B102
PC900
11P
TB914
15P
TB913
11P
TB912
15P
TB911
2P
TB905
INTERSWITCH UNIT
NQE-3141-2
CH1
CH2
50P
J4105
50P
J4106
50P
J4107
*OPTION
W401 H -7ZCRD1339
W402 H -7ZCRD1339
W403 H -7ZCRD1339
64P
J4103
64P
J4104
64P
J4102
64P
J4101
64P
J4401 64P
J4402 64P
J1
GYRO INTERFACE
CIRCUIT
CMJ-462E
PC420
RADAR PROCESS
CIRCUIT
CDC-1324
PC440
MOTHERBOARD
CQC-1192
PC410
64P
J4403
64P
J4404
AIS PROCESS
CIRCUIT
CDC-1325
PC460
64P
J4601
64P
J4501
ARPA PROCESS
CIRCUIT
CDC-1186D
PC450
15P
J4409
VGA
15P
J4405
VGA
28P
J4406
DVI-D
8P
J4407
RJ-45
50P
J4408
CF-card
LCD
OPERATION
CIRCUIT
CCK -972 PC710
8P
J711
MONITOR UNIT
NWZ-170-R
LCD PANEL
H-7WSRD0002A
8P
H-7ZCRD1328
9P 2m H-7ZCRD 1329A (NWZ-170-R )
DVI 2m H-7ZCRD1345 (NWZ-170-R)
20P
J4108
8P
POWER SUPPLY
CBD-1661
18P
20P
*PS/2 MOUSE/TRKBALL
(USER SUPPLY)
*OPTION
(USER SUPPLY)
2P
2P
AC OUT2
+
ー
U
V
W
BATTERY
IN
AC OUT2
AC IN
U
W
V
U
W
V
4351A07335 FILTER
INOUT
RED
WHT
BLU
RED
WHT
BLU
AC 2m 5ZCGH00285 (NWZ-170-R)
U V FG
+ーFG
TB522
AC IN
TB521
DC24V OUT
AC/DC
CONVERTER UNIT
NBA-5135
AC100-115V 50/60Hz
AC220-240V 50/60Hz
SCANNER MOTOR
POWER DC24V
NCD-4990 電源系統図
Power supply system diagram of DISPLAY UNIT type NCD-4990(self standing)
RADAR PROCESS UNIT
NDC-1399-9
W406 H-7ZCRD1342A
RED
WHT
RED
WHT
INPUT VOLTAGE
SELECT SWITCH
3.3V,5V,12V,-12V
P+5V P+12V
3.3V,5V,12V,-12V
+48V,DC+24V
+24V
P+5V
P+12V
DC+24V
+5V
U,V
AC100-115V
AC220-240V
50/60Hz,1φ
U,V
AC100-115V
AC220-240V
50/60Hz,1φ
U,V
AC100-115V
AC220-240V
50/60Hz,1φ
3.3V
5V
DC+24V
+48V
(to SCANNER UNIT)
3.3V,5V,
12V,-12V
3.3V,5V,12V,-12V
+48V,DC+24V
JMA -9 110 -6X A
JMA -9 110 -6X A H
JMA -9 122 -6X A H
only
B－12
JMA-9100 Instruction Manual > B.DRAWINGS > B.3 Signal Flow Diagram of Display Unit
B.3 Signal Flow Diagram of Display Unit
Fig B-11: Signal Flow Diagram of NCD-4990/T
2P
J4308
26P
J4307
26P
J4306
50P
J4301
18P
J4304
8P
J4305
3P
J4313
3P
J4314
9P
J4309
14P
TB4101
TO TRU
TO ISW
26P
TB4201
TO EXT-RADAR
30P
TB4401
TO S ENSOR
22P
TB4501
TO A LAR M SYSTEM
22P
TB4601
TO GYRO
6P
TB4701
TO LOG
12P
TB4701
TO PC
9P
J4310
TERMINAL BOARD
CQD-2097
PC430
50P
J4302
50P
J4303
30P
J4311
TO OPU
30P
J4312
TO SUB OPU
6P
J6411
6P
J6410 6P
J6409
6P
J6408 2P
J6406 7P
J6405 14P
J6404 14P
J6403 15P
J6402
30P
J6401
OPERATION CIRCUIT D
CCK-976
PC640
14P
J6101 15P
J6102
OPERATION
CIRCUIT A
CCK-973
PC610
7P
J6201
OPERATION
CIRCUIT B
CCK-974
PC620
SP1
A1
*PS/2 EXTENSION CA BLE
(USER SU PPLY )
OPERATION UNIT
NCE-5163-R
2m H-7ZCRD1337 (NCE-5163-R)
5m H-7ZCRD1338 (NCE-5163-RT)
JRC SU PPLY
B101
B102
PC900
11P
TB914
15P
TB913
11P
TB912
15P
TB911
2P
TB905
INTERSWITCH UNIT
NQE-3141-2
CH1
CH2
50P
J4105
50P
J4106
50P
J4107
*OPTION
W401 H-7ZCRD1339
W402 H-7ZCRD1339
W403 H-7ZCRD1339
64P
J4103
64P
J4104
64P
J4102
64P
J4101
64P
J4401 64P
J4402 64P
J1
GYRO INTERFACE
CIRCUIT
CMJ-462E
PC420
RADAR PROCESS
CIRCUIT
CDC-1324
PC440
MOTHERBOARD
CQC-1192
PC410
64P
J4403
64P
J4404
AIS PROCESS
CIRCUIT
CDC-1325
PC460
64P
J4601
64P
J4501
ARPA PROCESS
CIRCUIT
CDC-1186D
PC450
15P
J4409
VGA
15P
J4405
VGA
28P
J4406
DVI-D
8P
J4407
RJ-45
50P
J4408
CF-card
LCD
OPERATION
CIRCUIT
CCK -972 PC710
8P
J711
MONITOR UNIT
NWZ-170-R
LCD PANEL
H-7WSRD0002A
8P
H-7ZCRD1328
9P 2m H-7ZCRD 1329A (NWZ-170-R )
DVI 2m H-7ZCRD1345 (NWZ-170-R)
20P
J4108
8P
POWER SUPPLY
CBD-1661
18P
20P
*PS/2 MOUSE/TRKBALL
(USER SUPPLY)
*OPTION
(USER SUPPLY)
2P
2P
AC OUT2
+
ー
U
V
W
BATTERY
IN
AC OUT2
AC IN
U
W
V
U
W
V
4351A07335 FILTER
INOUT
RED
WHT
BLU
RED
WHT
BLU
AC 2m 5ZCGH00285 (NWZ-170-R)
U V FG
+ーFG
TB522
AC IN
TB521
DC24V OUT
AC/DC
CONVERTER UNIT
NBA-5135
AC100-115V 50/60Hz
AC220-240V 50/60Hz
SCANNER MOTOR
POWER DC24V
NCD-4990 信号系統図
Signal flow diagram of DISPLAY UNIT type NCD-4990
RADAR PROCESS UNIT
NDC-1399-9
W406 H-7ZCRD1342A
RED
WHT
RED
WHT
Serial
Radar vide
o
Trigger,Rot
a
Serial
Radar video,
Trigger,Rotati
o
Radar video,
Trigger,Rotati
o
Serial
Dry Contac
t
GYRO
(STEP/SY
N
LOG
(PULSE/SY
N
Serial
Radar video,
Trigger,Rotation
Radar video,
Trigger,Rotation
GYRO/LOG
Serial,GPIO
Radar video,
Trigger,Rotation
GYRO/LOG
Radar video,
Trigger,Rotation Serial,GPIO
Analog RGB
Analog RGB
Degital Video Interface
Ethernet LCD Fan Alarm
Power supply Control
Power supply Fan alarm
PS/2
I/F
PS/2
I/F Audio KEY matrix
Encoder
Power SW
Power supply Control
Power supply Fan alarm
Dimmer
JMA-9100 Instruction Manual > B.DRAWINGS > B.4 Primary Power System Diagram
B－13
B
B.4 Primary Power System Diagram
Fig B-12: Primary Power System Diagram
POWER CONTROL
CIRCUIT
FAN ALM POWER CONTROL
INTERSWITCH=1A
OPERATION UNIT=0.5A(typ)
GYRO I/F CIRCUIT=0.1A(typ)
SCANNER
X BAND_2.5A, S BAND_3.0A
RADAR PROCESS CIRCUIT = 1.2A(typ)
ARPA PROCESS CIRCUIT = 0.15A(typ)
AIS PROCESS CIRCUIT = 0.15(typ)
TERMINAL BOARD = 1.0A(typ)
AC100-115V
AC220-240V
50/60Hz,1φ
SCANNER
MOTOR
POWER
AC100/230V
1φ
OVER VOLT AG E
PROT ECTION
AC100-115V
AC220-240V
50/60Hz,1φ
RADAR PROCESS CIRCUIT = 2.2A(typ)
ARPA PROCESS CIRCUIT = 0.1A(typ)
AIS PROCESS CIRCUIT = 0.1(typ)
TERMINAL BOARD = 0.2A(typ)
RADAR PROCESS CIRCUIT = 0.1A(typ)
TERMINAL BOARD = 0.4A(typ)
RADAR PROCESS CIRCUIT = 0.1A(typ)
TERMINAL BOARD = 0.1A(typ)
BATTRY
DC24V
OPERATION UNIT = 0.1A
P+12V
+48V±3V
+5. 0V
+3. 3V
-12V
+12V
CIRCUIT
BREAKER LINE FI LT ER
VOLTAGE SELCT
SWITCH
MONITOR UNIT
POWER
SCANNER MOTOR
POWER
JMA-9100 Instruction Manual > B.DRAWINGS > B.5 Block Diagram of Scanner Unit
B－15
B
B.5.1 NKE-2103
Fig B-13: Block Diagram of NKE-2103
SLOT ANTENNA
MOTOR
B101
SAFETY SWITCH
S101
MAG
V101
PULSE
TRANS
SWITCHING
CIRCUIT
PC201
MH
GENERATOR
AVR
INTERFACE
CIRCUIT
PC1001
MIC
IF AMP
VIDEO
AMP
RECEIVER
Receiver
Bandwidth
Control
Tune Control
ΦA,ΦB,ΦZ
FILTER
DUMMY
LOAD
DC+24V
Serial Com, BP, BZ, VD, TRIG
NKE-2103 Scanner Unit
POWER
SUPPLY
CIRCUIT
MOTOR CONTROL
POWER
PC1501
Rotation Control
Speed control
Status
DC+24V
Tx Trigger/Pulse Width
DC+24V
DIODE
LIMITER
ENCODER
ROTARY
JOINT
B－16
JMA-9100 Instruction Manual > B.DRAWINGS > B.5 Block Diagram of Scanner Unit
B.5.2 NKE-2254
Fig B-14: Block Diagram of NKE-2254
SLOT ANTENNA
MOTOR
B101
SAFETY SWITCH
S101
MAG
V101
PULSE
TRANS
SWITCHING
CIRCUIT
PC201
MH
GENERATOR
AVR
PC1001
ΦA,ΦB,ΦZ
FILTER
DUMMY
LOAD
DC+24V
Serial Com, BP, BZ, VD, TRIG
NKE-2254 Scanner Unit
POWER
SUPPLY
CIRCUIT
MOTOR CONTROL
POWER
PC1501
Rotation Control
Speed control
Status
DC+24V
Tx Trigger/Pulse Width
DC+24V
ENCODER
ROTARY
JOINT
INTERFACE CIRCUIT
PC1101
RF AMP
IF AMP
VIDEO
AMP
RECEIVER
Receiver
Bandwidth
Control
Tune Control
DIODE
LIMITER
JMA-9100 Instruction Manual > B.DRAWINGS > B.5 Block Diagram of Scanner Unit
B－17
B
B.5.3 NKE-1125/NKE-1130
Fig B-15: Block Diagram of NKE-1125/NKE-1130
SLOT ANTENNA
ROTARY
JOINT ENCODER
MOTOR
B101
SAFETY SWITCH
S101
MAG
V101
PULSE
TRANS
SWITCHING
CIRCUIT
PC201
MH
GENERATOR
AVR INTERFACE CIRCUIT
PC1101
PC1001
DIODE
LIMITER
RF AMP
IF AMP
VIDEO
AMP
RECEIVER
Receiver
Bandwidth
Control
Tune Control
Tx Trigger/Pulse Width
ΦA,ΦB,ΦZ
FILTER
DUMMY
LOAD
MOTOR
DRIVER
PC1501
AC100/110/220 /230V
50/60Hz,1φ
DC+48V
Serial Com, BP, BZ, VD, TRIG
NKE-1130/NKE-1125 Scanner Unit
POWER
SUPPLY
CIRCUIT
MOTOR RELAY
PC1201
Relay Control
ERROR
Status
B－18
JMA-9100 Instruction Manual > B.DRAWINGS > B.5 Block Diagram of Scanner Unit
B.5.4 NKE-1129, NTG-3225 / NKE-1139, NTG-3230
Fig B-16: Block Diagram of NKE-1129, NTG-3225 / NKE-1139, NTG-3230
SLOT ANTENNA
ENCODER
MOTOR
B101
SAFETY SWITCH
S101
MAG
V101
PULSE
TRANS
INTERFACE CIRCUIT
PC1101
DIODE LIMITER
/ TRHPL PIN ATT
(X-band)
RF AMP
IF AMP
VIDEO
AMP
Receiver
Bandwidth
Control
Tune Control
ΦA,ΦB,ΦZ
DUMMY
LOAD
MOTOR
DRIVER
PC1501
AC100/110 /220/230V
50/60Hz,1φ
DC+48V
Serial Com, BP, BZ, VD, TRIG
NKE-1139/NKE-1129 Scanner Unit
NTG-3230/NTG-3225
Transceiver Unit
SWITCHING
CIRCUIT
PC201
MH
GENERATOR
PC1001
POWER
SUPPLY
CIRCUIT
RECEIVER
ERROR
MOTOR RELAY
PC1201
Relay Control
AC100/110/220/230V
50/60Hz,1φ
ROTARY
JOINT
Status
FILTER
AVR
Tx Trigger/Pulse Width
B－20
JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner Unit
B.6.1 NKE-2103
Fig B-17: Interconnection Diagram of NKE-2103
NKE-2103 / 2103HS
空中線機内接続図
SCANNER UNIT INTERCONNECTION
CAX-10
E101
NJT1969
A301
NJS6930
ANTENNA NAX-16B-4/6
FILTER
DUMMY
A101
1.TUNE
2.+5V
3.GND
4.NC
5.IF
IF AMP CIRCUIT (PC301)
CAE-529-1
MAG
MAGNETRON
V101
MAF1565N
POWER SUPPLY
CIRCUIT
(PC1001)
CBD-1783
1.2A
2.1A
J1001
J201
15.NC
4.PW1
5.MCT
6.MBK
7.+15V
8.AGND
9.-7V
10.BP
11.HSP
1.MPS
2.PW3
3.PW2
12.TI
13.+8V
14.MOD ID
T201-16
T201-15
1.MH
3.MN
J1003
J202
4.HTER
1.TIY
2.AGND
3.MAG.I
5.HVER
6.C2
7.BZ
J203
4.PMS
1.PTI
2.PTE
3.LVR
5.GND
6.TXI
7.TXE
1.2A
2.1A
J3
6.AGND
J1
4.AGND
1.E TIY
2.AGND
3.EXBP
5.ＥＸＢＺ
SAFETY SWITCH
WS101
MODULATOR CIRCUIT
(PC201)
CME-３６３
J301
15.NC
4.PW1
5.MCT
6.MBK
7.+15V
8.AGND
9.-7V
10.BP
11.HSP
1.MPS
2.PW3
3.PW2
12.TI
13.+8V
14.MOD ID
J302
4.HTER
1.TIY
2.AGND
3.MAG.I
5.HVER
6.C2
7.BZ
J303
4.PMS
1.PTI
2.PTE
3.LVR
5.GND
6.TXI
7.TXE
4.COM-
1.VD
2.VDE
3.COM+
J2
J18
1.HMCNT
2.+15V
3.GND
SE
B102
J8
4.PMS
1.PTI
2.PTE
3.LVR
5.E
6.TXI
7.TXE
4.ΦB
1.ΦZ
2.E
3.ΦA
5.+12V
6.F.G.
YEL
BLK
BLU
WHT
RED
SHIELD
DISPLAY
UNIT
P8 1.PTI
2.PTE
1.LVR
2.PMS
3.E
3.TXI
4.TXE
J81
J82
P81
P82
WHT
BLK
BLU
RED
BLK
WHT
BRN
PM
NJU-85
7ZCRD1280※
DISPLAY
UNIT
DISPLAY
UNIT
1.2A
2.1A
J1503
1.MPS
2.MCT
J1501
3.MBK
1.HMCNT
2.+15V
J1505
3.AGND
1.2A
2.1A
J4
1.2A
2.1A
J5
1.MPS
2.MCT
J209
3.MBK
1.C2G
2.C2
J210
1.2A
2.1A
J204
J206
1.MH
3.MN
MOTOR CONTROL POWER CIRCUIT
(PC1501)
CBD-1779
1.MCNT+
J125
3.NC
1.M+
2.NC
J1502
3.M-
4.NC
2.MC NT-
MOTOR
B101
H-7BDRD0048
MORTOR CBP-202
BREAK CIRCUIT CFA-252
YEL G RN
A103
RECEIVER UNIT ＮＲＧ－６１０
MIC
S.G.
S.G.
(W204)
ZCRD1312※
(W110) ZCRD1307※
(W107)
ZCRD1304※
(W103)
ZCRD13 06※
(W105)
ZCRD1300※
ZCRD1302※
(W101)
ZCRD1289※
(W102)
ZCRD1290※
(W10６)
ZCRD1303※
(W111)
ZCRD1308※
(W108)
ZCRD1305※
(OPTION）
5
4
2
1
J208
D.L
1.MS1
2.NC
J1504
3.MS2
TRANSMITTER/RECEIVER UNIT ＮZT－２１０３ TRANSMITTER/RECEIVER UNIT
INTER C ON NE CTIO N
CMK-599
8.NC
(W104)
ZCRD1301※
J205
1.+15V
2.+12V
3.+8V
4.AGND
5.-15V
6.X1
7.X2
8.+5V
9.HTER
10.HVER
J1002
1.+15V
2.+12V
3.+8V
4.AGN D
5.-15V
6.X1
7.X2
8.+5V
9.HTER
10.HVER
WV101
A102
(RECEIVER UNIT INTERCONNECTION CMA-823)
ENCODER CHT -71A
NJC4002
FCX68 FCX68
S.G.
CFR-234
MAG FILTER
CIRCUIT
100pF×3
A104
NJC9952
TB1
1-2short : Nomal Speed
2-3short : High Speed
H-7 ZCRD#### *:
“#” means specifi cation do cu ment No.
“*” means revisi on of the specfi cation docume nt.
JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner Unit
B－21
B
B.6.2 NKE-2254
Fig B-18: Interconnection Diagram of NKE-2254
NKE-2254 / 2254HS
空中線機内接続図
14.VDE
12.VD_DC
15.VD
9.TGT
10.TGTE
13.TNL
11.TNI
1.BS3
2.BS2
3.BS1
4.TNC
5.+5V
6.-15V
7.+15V
RECEIVER UNIT NRG-162A
RECEIVER CIRCUIT
CMA-866A
J101
BM15B-XASS-TE
T/R CONTROL CIRCUIT
CMC-1205R
1.MONI
2.GS
3.GSE
4.TGT
5.TGTE
6.TNL
7.-15V
8.TNI
9.+15V
10.GND
11.TRG2
1.BS3
2.BS2
3.BS1
4.TNC
5.MicPS
6.VDINE
7.VDIN
8.+5V
1.RXD
2.TXD
3.+5V
4.GND
1.SHORT
2.MAG I
3. X 1
4. X 2
5.T I
6.T IE
7.+15V
8.GND
9.NC
10.NC
11.NC
12.NC
1.HMCNT
2.+15V
3.GND
1.+15V
2.+12V
3.GND
4.GND
5.-15V
6.10V
7.10VE
8.+5V
1.MC T
2.MBK
3.TISTOP
4.G ND
5.MPS
6. MI E R
1. T IY
2.TIYE
3.BP
4.BPE
5.BZ
6.BZE
1.+12V
2.GN D
3.FAN_ERR1
1.HTER1
2.HVGATE1
3.TISTOP1
4.GND
5.CNT
6.+5V
7.+15V
8.STABY_REQ
9.NC
1.PW1
2.PW2
3.PW3
4.+24V
5.GN D
1.BP+
2.BP-
3.BZ+
4.BZ-
5.TRIG+
6.TRIG-
7.MTR+
8.MTR-
9.MTRE
10.VD+
11.VD-
1.V D
2.V DE
3.MTR+
4.MTR-
J1118
J1103J1104 J1111
J1191
J1110
J1109
TB101
J8 J1106
J1112 J1113
IL -G - 1 2P
IL-G-8P IL-G-11P
B6P-SHF
IL-G-9P
MSTBA2.5/11-G
IL-G-5P
B3P-SHF
IL-4P
B8P-SHF
IL-G-3P
MAG
POWER SUPPLY
CIRCUIT
CBD-1682A
1.+15V
2.+12V
3.+8V
4.GND
5.-15V
6.X1
7.X2
8.+5V
1.M C T
2.MBK
3.H S P
4.H T ER
5.TISTOP
6.C 2
7.GND
8.M P S
9.M I ER
2.1A
1.2A
2.1A
1.2A
2.1A
1.2A
1.MH
2.NC
3.MN
1.MH
2.NC
3.MN
1.X1
2.X2
No.2
No.1
2
1
4
35
6
FILTER
J1004 J1003
J 5J 4 J 3
J1001
J1002
J2102
J210 1
J2103
ANTENNA
1. S HO R T
2.MAG I
3. X 1
4. X 2
5. T I
6. T IE
7.+15V
B9P-SHF B8P-SHF
1586514-2
350209-1
IL-10P
350209-2
350209-1
350428-1
MODULATOR
CIRCUIT
CPA-264
MODULATOR UNIT
INTERCONNECTION
CMB-404
D.L
①②
③
①②
③
ﾐﾄﾞﾘ
ｷ
C201
0.0 1UF 1K V
C202
0.22UF 200V
R202
2.7KΩ
1/2W
C203
0.22UF
200V
T1
R201
150Ω
8W
H-7LPRD0122
CD202 CD201
MD-12N1MD-12N1
Ａ101 Ａ102
M1568BS
Ｖ101
P3001
P1109 P1110
P1104
P1103 P1003
P1004
P1111
PULSE TANS
P2103
DUMMY
Ａ103
(W001)
(W003)
P1002
1.+12V
2.GND
3.FAN_ERR2
J1114
IL-G-3P
1.+12V
2.C2
J1105
IL-G-2P
P1105
MODULATOR UNIT NMA-550
SCANNER UNIT INTERCONNECTION
CAX-15
(W106)
(W103)
(W104)
(W105)
ZCRD1255※
ZCRD1257※
P1505
J1
IL-G-6P
J2
IL- G -4P
ZCRD1256※
Ａ301
NJS6930
ZCRD1252※
ZCRD1258※
ZCRD1251※
ZCRD1253※
(W004)
(W207)
ZCRD1448※
ZCRD1254※
1.φZ
2.φZE
3.φ A
4.φB
5.+12V
6.GND
J13
IL-6P
50/60ｋW
RED
WHT
DISPLAY UNIT
P2101
P2102
8.GND
1.M+
2.M-
1586514-2
NJC4002
9.NC
10.NC
B02P-NV(LF)(SN）
S. G.
S.G.S.G.
8.G ND
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
WHT
BLK
P1118
BLU
WHT
BLK
BLU
P1301
J1301
(W006)
1
2
3
4
1
2
3
4
5
6
5
6
7
8
7
8
SE
YE L
BLK
BLU
WHT
RED
SHIELD
B102
ENCODER CHT-71A
P13
(W017)
FAN
RED
BLU
YEL
B201
B202
FAN
RED
BLU
YEL
(W009)
(W010)
P1113 P1114
RED
WHT
ZCRD1447※
(W206)
ｼﾛ
ｸﾛ
ｱｵ
12
BLK.T
21 3
3
BLK.T
(W107)
ZCRD1259※
J1303
P1303
P1302
J1302
(W201)
ZCRD1260※
1.PTI
2.P T E
3.LVR
4.PMS
5.GN D
6.TXI
7. T X E
8.NC
IL-8P
1.PTI
2.PTE
1.LVR
2.PMS
3.E
3.TXI
4.TXE
J82
J81
PM
P81
P82
WHT
BLK
BLU
RED
BLK
WHT
BRN
NJU-85
ZCRD1280※
(W018)
ZCRD1277※
S.G.
S101
S-32
21
7
54
8
CBD-1779
IL-3P-S3EN2
J1505
1.H MC N T
2.+15V
3.E
J1504
1. M S 1
2.NC
3.MS2
ｱｶ太
P1504
B3 P- V H
P1501
J1501
1.MPS
2.MCT
IL- G -3 P- S3 T 2 -SA
(W302)
ZCRD1449※
(W307)
J1503
IL-2P-S3EN2
R1
10Ω ,1 0W
P1503
ZCRD1450※
GRN
BRN
BLU.T
MOTOR CBP-168A / CBP-182
YE L
1.M+
2.NC
3.M-
4.NC
B4P-VH
P1502
J125
1.M CN T -
2.M CN T +
3.NC
P125
B3P-SHF-1AA
P1502
B101
MOTOR CONTROL
POWER CIRCUIT
(W305)
(W301)
BLK.T
DISPLAY UNIT
MOTOR
BREAK CIRCUIT
CFA-257
NJC3901M NJC3901M
H-7BFRD0002
H-7BFRD0002
NJC9952
Ａ104
SAFETY SWITCH
CSD-653
1.2A
2.1A
1.2A
2.1A
J4
350209-1
J5
350209-1
3.MBK
ZCRD1451※
(W208)
ZCRD1494※
(W308
※NKE-2254HS
・MOTOR CBP-182
UVUTH
UVUTH
TH101
WHT.T
TR101
（100W）
ｼﾛ太
HEATER CONTROL
PART
CHG-216
（OPTION）
TB105
S.G.
CFR-229
MAG FIL TER
CIRCUIT
220pF×5
ZCRD1508※
(W401)
H-7ZCRD####*:
“#” means speci fication document No.
“*” means revision of the specficatio n document.
B－22
JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner Unit
B.6.3 NKE-1125 (AC110V)
Fig B-19: Interconnection Diagram of NKE-1125 (AC110V)
NKE-1125PM (AC100V)
空中線機内接続図
14.VDE
12.VD_DC
15.VD
9.TGT
10.TGTE
13.TNL
11.TNI
1.BS3
2.BS2
3.BS1
4.TNC
5.+5V
6.-15V
7.+15V
RECEIVER UNIT NRG-162A
RECEIVER CIRCUIT CMA-866A
J101
BM15B-XASS-TE
T/R CONTROL CIRCUIT
CMC-1205R
1.MONI
2.GS
3.GSE
4.TGT
5.TGTE
6.TNL
7.-15V
8.TNI
9.+15V
10.GND
11.TRG2
1.BS3
2.BS2
3.BS1
4.TNC
5.MicPS
6.VDINE
7.VDIN
8.+5V
1.RXD
2.TXD
3.+5V
4.GND
1.SHORT
2.M AG I
3. X 1
4. X 2
5. T I
6. T IE
7.+15V
8.GND
9.NC
10.NC
11.NC
12.NC
1.HMCNT
2.+15V
3.GND
1.+15V
2.+12V
3.GND
4.GND
5.-15V
6.10V
7.10VE
8.+5V
1.MC T
2.MBK
3.TISTOP
4.G ND
5.MPS
6. MI E R
1. T IY
2.TIYE
3.BP
4.BPE
5.BZ
6.BZE
1.+12V
2.GN D
3.FAN_ERR1
1.HTER1
2.HVGATE1
3.TISTOP1
4.GND
5.CNT
6.+5V
7.+15V
8.STABY_REQ
9.NC
1.PW1
2.PW2
3.PW3
4.+24V
5.GN D
1.BP+
2.BP-
3.BZ+
4.BZ-
5.TRIG+
6.TRIG-
7.MTR+
8.MTR-
9.MTRE
10.VD+
11.VD-
1.VD
2.VDE
3.MTR+
4.MTR-
J1118
J1103J1104 J1111
J1191
J1110
J1109
TB101
J8 J1106
J1112 J1113
IL -G - 1 2P
IL-G-8P IL-G-11P
B6P-SHF
IL-G-9P
MSTBA2.5/11-G
IL-G-5P
B3P-SHF
IL-4P
B8P-SHF
IL-G-3P
MAG
POWER SUPPLY
CIRCUIT
CBD-1682A
1.+15V
2.+12V
3.+8V
4.GND
5.-15V
6.X1
7.X2
8.+5V
1.MC T
2.MBK
3. HS P
4. HT E R
5.TISTOP
6.C 2
7.GND
8.MPS
9. MI E R
2.1A
1.2A
2.1A
1.2A
2.1A
1.2A
1.MH
2.NC
3.MN
1.MH
2.NC
3.MN
1. X 1
2. X 2
No.2
No.1
2
1
4
35
6
FILTER
J1004 J1003
J 5J 4 J 3
J1001
J1002
J2102
J2101
J2103
ANTENNA
1. SH O R T
2.MA G I
3.X1
4.X2
5.TI
6.TIE
7.+15V
B9P-SHF B8P-SHF
1586514-2
350209-1
IL-10P
350209-2
350209-1
350428-1
MODULATOR
CIRCUIT
CPA-264
MODULATOR UNIT
IN T ERCO N NECTI ON
CMB-404
D.L
①②
③
①②
③
GRN
YEL
C201
0.01UF 1KV
C202
0.22UF 200V
R202
2.7KΩ
1/2W
C203
0.22UF
200V
T1
R201
150Ω
8W
H-7LPRD0122
CD202 CD201
MD-12N1MD-12N1
NJC3901M
Ａ101 Ａ102
P3001
P1109 P1110
P1104
P1103 P1003
P1004
P1111
PULSE
TRANS
P3
P2103
DUMMY
A103
(W001)
(W003)
P1002
1.+12V
2.GND
3.FAN_ERR2
J1114
IL-G-3P
1.+12V
2.C2
J1105
IL-G-2P
P1105
MODULATOR UNIT NMA-550
SCANNER UNIT INTERCONNECTION
CAX-11
(W106)
(W103)
(W104)
(W105)
ZCRD1255※
ZCRD1257※
J1
IL-G-6P
J2
IL- G -4P
ZCRD1256※
A301
NJS6930
ZCRD1252※
ZCRD1258※
ZCRD1251※
ZCRD1253※
(W004)
(W207)
ZCRD1263※
ZCRD1254※
1.φZ
2.φZE
3.φ A
4.φB
5.+12V
6.GND
J13
IL-6P
50/60ｋW
ｱｶ
ｼﾛ
DISPLAY UNIT
P2101
P2102
8.GND
1.M+
2.M-
1586514-2
NJC4002
9.NC
10.NC
B02P-NV(LF)(SN ）
S. G.
S.G.S.G.
8.G ND
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
WHT
BLK
P1118
BLU
WHT
BLK
BLU
P1301
J1301
(W006)
1
2
3
4
1
2
3
4
5
6
5
6
7
8
7
8
SE
YEL
BLK
BLU
WHT
RED
SHIELD
B102
ENCODER CHT-71A
P13
(W017)
FAN
RED
BLU
YEL
B201
B202 FAN
RED
BLU
YEL
P1113 P1114
RED
WHT
ZCRD1262※
(W206)
12
BLK.T
21 3
3
BLK.T
(W107)
ZCRD1259※
J1303
P1303
P1302
J1302
(W201)
ZCRD1260※
W101
W101
1.PTI
2.P T E
3.LVR
4.PMS
5.GN D
6.TXI
7. T X E
8.NC
IL-8P
1.PTI
2.PTE
1.LVR
2.PMS
3.E
3.TXI
4.TXE
J82
J81
PM
P81
P82
WHT
BLK
BLU
RED
BLK
WHT
BRN
NJU-85
ZCRD1280※
(W018)
ZCRD1277※
X25kW,2ﾕﾆｯﾄ
S.G.
NJC3901M
H-7BFRD0002
H-7BFRD0002
M1568BS
Ｖ101
NJC9952
Ａ104
CFR-229
MAG FILTER
CIRCUIT
S.G.
220pF×5
HEATER
CONTROL PART
CHG-216
（OPTION）
+48V
+48VG
U1
V1
W1
U1
W1
V1
DISPLAY UNIT
TB102
+48V
+48VG
(W301)
S101
S-32F
21
7
54
8
RED.T RED.T
BLK.T
BLK.T
ZCRD1264※
(W302)
ZC RD 12 65※
+12V
ZCRD1261※
(W203)
SAFETY SWITCH
CSD-654
to CCB-655 J1941
ZCRD1537※
(W308)
UVUTH
UVUTH
TH101
W401 7ZCRD1508※
TR101
（100W）
TB105
WHT.T
WHT.T
WHT
BLK
BLU
ZCRD1454※
(W305)
P1212
BRAKE CIRCUIT
CFA-253
J1501
1.VERR
2.E
H-7EPRD0035
B201
J1505
PC1501
P1501
B2P-VH
P1505
P1201
RELAY FIL TER
CIRCUIT
CSC-656
PC1201
IL-3P
1.HMCNT
2.+15V
3.G ND
P1211
J1212
1.VERR1
2.E
J1201
J1211
1.U1
3.V1
2.NC
4.NC
B4P-VH
IL-2P
1.VERR1
2.E
1.VERR
2.E
1.P
2.NC
3.N
1.P
2.N
1.BKH1
3.BKH1
1.BKS1
2.BKS2
1.+12V
2.NC
3.+12VE
P1941 J1941
J1903
P1903
J1905
P1905
J1912 P1912
BRAKE CONTROL CIRCUIT
CCB-655
P1502
J1921
P1921
J1911
P1911
to TB102
RED
BLK
IL-2P
B2PS-VH
S3B-XH-A
1-350210-0 1-350209-0
1-480700-0
ZC RD 15 37※
(W308)
ZCRD1536※
(W307)
ZCRD1452※
(W303)
WC1
ZCRD1538※
(W309)
ZCRD1539※
(W310)
CBP-203
H-7BDRD0050
2.NC
4.NC
1.S1
2.S2
3.S3
4.S4
5.S5
6.S6
J1502
J1503
3.M2
1.M1
5.M3
P1503
MOTOR
MOTOR
B101
BRAKE CIRCUIT B
CFA-260
BRAKE CIRCUIT A
CFA-259
R1
R2
R3
R4
R1
120Ω
30W
330Ω
30W
×4
×1
2.NC
3.MV2
1.MU2
2.NC
4.NC
5.NC
6.G N D
B6P-VH
(W304)
ZCRD1314※
R1
R2
P1504
1.R1
3.R2
J1504
B3P-VH
2.NC
P1202
1.MU2
3.MV2
J1202
2.GND
B3P-NV
1.2kΩ
30W
×2
AC100V
MOTOR DRIVER
CBD-2001
JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner Unit
B－23
B
B.6.4 NKE-1125 (AC220V)
Fig B-20: Interconnection Diagram of NKE-1125 (AC220V)
NKE-1125PM (AC220V)
空中線機内接続図
14.VDE
12.VD_DC
15.VD
9.TGT
10.TGTE
13.TNL
11.TNI
1.BS3
2.BS2
3.BS1
4.TNC
5.+5V
6.-15V
7.+15V
RECEIVER UNIT NRG-162A
RECEIVER CIRCUIT CMA-866A
J101
BM15B-XASS-TE
T/R CONTROL CIRCUIT
CMC-1205R
1.MONI
2.GS
3.GSE
4.TGT
5.TGTE
6.TNL
7.-15V
8.TNI
9.+15V
10.GND
11.TRG2
1.BS3
2.BS2
3.BS1
4.TNC
5.MicPS
6.VDINE
7.VDIN
8.+5V
1.RXD
2.TXD
3.+5V
4.GND
1.SHORT
2.M AG I
3. X 1
4. X 2
5. T I
6. T IE
7.+15V
8.GND
9.NC
10.NC
11.NC
12.NC
1.HMCNT
2.+15V
3.GND
1.+15V
2.+12V
3.GND
4.GND
5.-15V
6.10V
7.10VE
8.+5V
1.MC T
2.MBK
3.TISTOP
4.G ND
5.MPS
6. MI E R
1. T IY
2.TIYE
3.BP
4.BPE
5.BZ
6.BZE
1.+12V
2.GN D
3.FAN_ERR1
1.HTER1
2.HVGATE1
3.TISTOP1
4.GND
5.CNT
6.+5V
7.+15V
8.STABY_REQ
9.NC
1.PW1
2.PW2
3.PW3
4.+24V
5.GN D
1.BP+
2.BP-
3.BZ+
4.BZ-
5.TRIG+
6.TRIG-
7.MTR+
8.MTR-
9.MTRE
10.VD+
11.VD-
1.VD
2.VDE
3.MTR+
4.MTR-
J1118
J1103J1104 J1111
J1191
J1110
J1109
TB101
J8 J1106
J1112 J1113
IL -G - 1 2P
IL-G-8P IL-G-11P
B6P-SHF
IL-G-9P
MSTBA2.5/11-G
IL-G-5P
B3P-SHF
IL-4P
B8P-SHF
IL-G-3P
MAG
POWER SUPPLY
CIRCUIT
CBD-1682A
1.+15V
2.+12V
3.+8V
4.GND
5.-15V
6.X1
7.X2
8.+5V
1.MC T
2.MBK
3. HS P
4. HT E R
5.TISTOP
6.C 2
7.GND
8.MPS
9. MI E R
2.1A
1.2A
2.1A
1.2A
2.1A
1.2A
1.MH
2.NC
3.MN
1.MH
2.NC
3.MN
1. X 1
2. X 2
No.2
No.1
2
1
4
35
6
FILTER
J1004 J1003
J 5J 4 J 3
J1001
J1002
J2102
J2101
J2103
ANTENNA
1. SH O R T
2.MA G I
3.X1
4.X2
5.TI
6.TIE
7.+15V
B9P-SHF B8P-SHF
1586514-2
350209-1
IL-10P
350209-2
350209-1
350428-1
MODULATOR
CIRCUIT
CPA-264
MODULATOR UNIT
IN T ERCO N NECTI ON
CMB-404
D.L
①②
③
①②
③
GRN
YEL
C201
0.01UF 1KV
C202
0.22UF 200V
R202
2.7KΩ
1/2W
C203
0.22UF
200V
T1
R201
150Ω
8W
H-7LPRD0122
CD202 CD201
MD-12N1MD-12N1
NJC3901M
Ａ101 Ａ102
P3001
P1109 P1110
P1104
P1103 P1003
P1004
P1111
PULSE
TRANS
P3
P2103
DUMMY
A103
(W001)
(W003)
P1002
1.+12V
2.GND
3.FAN_ERR2
J1114
IL-G-3P
1.+12V
2.C2
J1105
IL-G-2P
P1105
MODULATOR UNIT NMA-550
SCANNER UNIT INTERCONNECTION
CAX-11
(W106)
(W103)
(W104)
(W105)
ZCRD1255※
ZCRD1257※
J1
IL-G-6P
J2
IL- G -4P
ZCRD1256※
A301
NJS6930
ZCRD1252※
ZCRD1258※
ZCRD1251※
ZCRD1253※
(W004)
(W207)
ZCRD1263※
ZCRD1254※
1.φZ
2.φZE
3.φ A
4.φB
5.+12V
6.GND
J13
IL-6P
50/60ｋW
ｱｶ
ｼﾛ
DISPLAY UNIT
P2101
P2102
8.GND
1.M+
2.M-
1586514-2
NJC4002
9.NC
10.NC
B02P-NV(LF)(SN ）
S. G.
S.G.S.G.
8.G ND
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
WHT
BLK
P1118
BLU
WHT
BLK
BLU
P1301
J1301
(W006)
1
2
3
4
1
2
3
4
5
6
5
6
7
8
7
8
SE
YEL
BLK
BLU
WHT
RED
SHIELD
B102
ENCODER CHT-71A
P13
(W017)
FAN
RED
BLU
YEL
B201
B202 FAN
RED
BLU
YEL
P1113 P1114
RED
WHT
ZCRD1262※
(W206)
12
BLK.T
21 3
3
BLK.T
(W107)
ZCRD1259※
J1303
P1303
P1302
J1302
(W201)
ZCRD1260※
W101
W101
1.PTI
2.P T E
3.LVR
4.PMS
5.GN D
6.TXI
7. T X E
8.NC
IL-8P
1.PTI
2.PTE
1.LVR
2.PMS
3.E
3.TXI
4.TXE
J82
J81
PM
P81
P82
WHT
BLK
BLU
RED
BLK
WHT
BRN
NJU-85
ZCRD1280※
(W018)
ZCRD1277※
X25kW,2ﾕﾆｯﾄ
S.G.
NJC3901M
H-7BFRD0002
H-7BFRD0002
M1568BS
Ｖ101
NJC9952
Ａ104
CFR-229
MAG FILTER
CIRCUIT
S.G.
220pF×5
HEATER
CONTROL PART
CHG-216
（OPTION）
+48V
+48VG
U1
V1
W1
U1
W1
V1
DISPLAY UNIT
TB102
+48V
+48VG
(W301)
S101
S-32F
21
7
54
8
RED.T RED.T
BLK.T
BLK.T
ZCRD1264※
(W302)
ZC RD 12 65※
+12V
ZCRD1261※
(W203)
SAFETY SWITCH
CSD-654
to CCB-655 J1941
ZCRD1537※
(W308)
UVUTH
UVUTH
TH101
W401 7ZCRD1508※
TR101
（100W）
TB105
WHT.T
WHT.T
WHT
BLK
BLU
ZCRD1454※
(W305)
P1212
BRAKE CIRCUIT
CFA-253
J1501
1.VERR
2.E
H-7EPRD0034
B201
J1505
PC1501
P1501
B2P-VH
P1505
P1201
RELAY FIL TER
CIRCUIT
CSC-656
PC1201
IL-3P
1.HMCNT
2.+15V
3.G ND
P1211
J1212
1.VERR1
2.E
J1201
J1211
1.U1
3.V1
2.NC
4.NC
B4P-VH
IL-2P
1.VERR1
2.E
1.VERR
2.E
1.P
2.NC
3.N
1.P
2.N
1.BKH1
3. BK H 2
1.B K S1
2.BKS2
1.+12V
2.NC
3.+12VE
P1941 J1941
J1903
P1903
J1905
P1905
J1912 P1912
BRAKE CONTROL CIRCUIT
CCB-655
P1502
J1921
P1921
J1911
P1911
to TB102
RED
BLK
IL-2P
B2PS-VH
S3B-XH -A
1-350210-0 1-350209-0
1-480700-0
ZC RD 15 37※
(W308)
ZCRD1536※
(W307)
ZCRD1452※
(W303)
WC1
ZCRD1538※
(W309)
ZCRD1539※
(W310)
CBP-203
H-7BDRD0050
2.NC
4.NC
1.S1
2.S2
3.S3
4.S4
5.S5
6.S6
J1502
J1503
3.M2
1.M1
5.M3
P1503
MOTOR
MOTOR
B101
BRAKE CIRCUIT B
CFA-260
BRAKE CIRCUIT A
CFA-259
R1
R2
R3
R4
R1
120Ω
30W
330Ω
30W
×4
×1
2.NC
3.MV2
1.MU2
2.NC
4.NC
5.NC
6.G N D
B6P-VH
(W304)
ZCRD1314※
R1
R2
P1504
1.R1
3.R2
J1504
B3P-VH
2.NC
P1202
1.MU2
3.MV2
J1202
2.GND
B3P-NV
1.2kΩ
30W
×2
AC220V
MOTOR DRIVER
CBD-2000
B－24
JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner Unit
B.6.5 NKE-1129 (AC110V)
Fig B-21: Interconnection Diagram of NKE-1129 (AC110V)
NKE-1129PM (AC100V)
空中線機内接続図
SCANNER UNIT INTERCONNECTION
CAX-12
J82
J81 P81
P82
WHT
BLK
BLU
RED
BLK
WHT
BRN
U1
V1
W1
+12V
C2
ΦZE
ΦZ
ΦA
E
ΦB
RED
SHIELD
YEL
BLU
WHT
SE
B102
BLKBLK
ENCORDER CHT-71A1
C102C101
2200p
50V
1000μ
16V
+
S101
S-32
21
7
54
8
RED.T
BLK.T
RED
PTI
PTE
LVR
PMS
E
TXI
TXE
VERR1
E
WHT
RED.T
BLK.T
TRANSCEIVER UNIT
TRANSCEIVER UNIT
1
1
BLU
RED
BLK
PM
NJU-85
ZCRD1280※
TB103
TB104
（W301) ZCRD1285※
（W303) ZCRD1278※
SAFETY SWITCH CSD-655
（W302) ZCRD1286※
S.G.S.G.
S.G .
S.G.
Xﾊﾞﾝﾄﾞ, 3ﾕﾆｯﾄ
TRANSCEIVER UNIT
（W305)
ZCRD1455※
TH101
TR101
（100W）
WHT.T
HEATER CO NTROL P ART
CHG-216
(OPTION)
U
V
UTH
AC100V
TB105
W401 7ZCRD1508※
WHT.T
WHT.T
ZCRD1548※
1.VERR1
2.E
1.VER R
2.E
1.P
2.NC
3.N 1.BKH1
3.BK H2
1.BKS1
2.BKS2
1.+12V
2.NC
3.+12VE
P1941 J1941
J1903
P1903
J1905
P1905
J1912
P1912
BRAKE CONTROL CIRCUIT
CCB-655
J1921
P1921
J1911
P1911
1.RED
3.BLK
IL-2P
S3B-XH-A
1-350210-0 1-350209-0
ZCRD1547※
(W307 )
ZCRD1538※
(W309)
ZCRD1539※
(W310)
CBD-2001
BRAKE CIRCUIT
CFA-253
J1501
1.VERR
2.E
H-7EPRD0035B201
J1505
PC1501
P1501
B2P-VH
1.P
2.N
P1502
AC100V
WC1
CBP-203
H-7BDRD0050
2.NC
4.NC
1.S1
2.S2
3.S3
4.S4
5.S5
6.S6
J1502
J1503
3.M2
1.M1
5.M3
P1503
MOTOR
MOTOR
B101
(W308)
MOTOR DRIVER
BRAKE CIRCUIT B
CFA-260
BRAKE CIRCUIT A
CFA-259
R1
R2
R3
R4
R1
120Ω
30W
330Ω
30W
×4
×1
2.NC
3.M V 2
1.MU2
2.N C
4.N C
5.N C
6.GND
B6P-VH
1.2kΩ
30W
1.2kΩ
30W
(W304)
ZCRD1314※
R1R2
P1504
1.R 1
3.R2
J1504
B3P-VH
2.NC
JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner Unit
B－25
B
B.6.6 NKE-1129 (AC220V)
Fig B-22: Interconnection Diagram of NKE-1129 (AC220V)
NKE-1129PM (AC220V)
空中線機内接続図
SCANNER UNIT INTERCONNECTION
CAX-12
J82
J81 P81
P82
WHT
BLK
BLU
RED
BLK
WHT
BRN
U1
V1
W1
+12V
C2
ΦZE
ΦZ
ΦA
E
ΦB
RED
SHIELD
YEL
BLU
WHT
SE
B102
BLKBLK
ENCORDER CHT-71A1
C102C101
2200p
50V
1000μ
16V
+
S101
S-32
21
7
54
8
RED.T
BLK.T
RED
PTI
PTE
LVR
PMS
E
TXI
TXE
VERR1
E
WHT
RED.T
BLK.T
TRANSCEIVER UNIT
TRANSCEIVER UNIT
1
1
BLU
RED
BLK
PM
NJU-85
ZCRD1280※
TB103
TB104
（W301) ZCRD1285※
（W303) ZCRD1278※
SAFETY SWITCH CSD-655
（W302) ZCRD1286※
S.G.S.G.
S.G .
S.G.
Xﾊﾞﾝﾄﾞ, 3ﾕﾆｯﾄ
TRANSCEIVER UNIT
（W305)
ZCRD1455※
TH101
TR101
（100W）
WHT.T
HEATER CO NTROL P ART
CHG-216
(OPTION)
U
V
UTH
AC100V
TB105
W401 7ZCRD1508※
WHT.T
WHT.T
ZCRD1548※
1.VERR1
2.E
1.VER R
2.E
1.P
2.NC
3.N 1.BKH1
3.BK H2
1.BKS1
2.BKS2
1.+12V
2.NC
3.+12VE
P1941 J1941
J1903
P1903
J1905
P1905
J1912
P1912
BRAKE CONTROL CIRCUIT
CCB-655
J1921
P1921
J1911
P1911
1.RED
3.BLK
IL-2P
S3B-XH-A
1-350210-0 1-350209-0
ZCRD1547※
(W307 )
ZCRD1538※
(W309)
ZCRD1539※
(W310)
CBD-2000
BRAKE CIRCUIT
CFA-253
J1501
1.VERR
2.E
H-7EPRD0034B201
J1505
PC1501
P1501
B2P-VH
1.P
2.N
P1502
AC220V
WC1
CBP-203
H-7BDRD0050
2.NC
4.NC
1.S1
2.S2
3.S3
4.S4
5.S5
6.S6
J1502
J1503
3.M2
1.M1
5.M3
P1503
MOTOR
MOTOR
B101
(W308)
MOTOR DRIVER
BRAKE CIRCUIT B
CFA-260
BRAKE CIRCUIT A
CFA-259
R1
R2
R3
R4
R1
120Ω
30W
330Ω
30W
×4
×1
2.NC
3.M V 2
1.MU2
2.N C
4.N C
5.N C
6.GND
B6P-VH
1.2kΩ
30W
1.2kΩ
30W
(W304)
ZCRD1314※
R1R2
P1504
1.R 1
3.R2
J1504
B3P-VH
2.NC
B－26
JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner Unit
B.6.7 NTG-3225
Fig B-23: Interconnection Diagram of NTG-3225
NTG-3225
送受信機機内接続図
14.VDE
12.VD_DC
15.VD
9.TGT
10.TGTE
13.TNL
11.TNI
1. BS 3
2. BS 2
3. BS 1
4. T NC
5.+5V
6.-15V
7.+15V
RECEIVER UNIT NRG-162A
RECEIVER CIRCUIT
CMA-866A
J101
BM15B-XASS-TE
T/R CONTROL CIRCUIT
CMC-1205R
1. MO N I
2.GS
3.GSE
4.TGT
5.TGTE
6.TNL
7.-15V
8.TNI
9.+15V
10.GND
11.TRG2
1.BS3
2.BS2
3.BS1
4.TNC
5.MicPS
6.VDINE
7.VDIN
8.+5V
1.RXD
2.TXD
3.+5V
4.GND
1. S HO RT
2.MAGI
3. X 1
4. X 2
5. T I
6. T IE
7.+15V
8.GND
9.NC
10.NC
11.NC
12.NC
1.HMCN T
2.+15V
3.GND
1.+15V
2.+12V
3.G ND
4.GND
5.-15V
6.10V
7.10VE
8.+5V
1.MCT
2.MBK
3. T IS TO P
4.GND
5.MPS
6.MIE R
1.TIY
2.TIYE
3.BP
4.BPE
5.BZ
6.BZE
1.+12V
2.GND
3.FAN_ERR1
1.HT ER 1
2. HV GA T E1
3. T IS T O P1
4.GN D
5.CN T
6.+5V
7.+15V
8. S T A BY _R E Q
9.NC
1.PW1
2.PW2
3.PW3
4.+24V
5.GND
1.PTI
2.PTE
3.LVR
4.PMS
5.GND
6.TXI
7.TXE
8.NC
1. BP +
2. BP -
3.BZ +
4.BZ -
5.TRIG+
6.TRIG-
7.MTR+
8.MTR-
9. MT R E
10.VD+
11.VD-
1.VD
2.VDE
3.M T R+
4.M T R-
J1118J1103J1104 J1111
J1191
J1110
J1109
TB101
J8 J1106
J1112 J1113
IL-G-12P
IL-8P
IL-G-8P IL-G-11P
B6P-SHF
IL-G-9P
MSTBA2.5/11-G
IL- G -5P
B3P-SHF
IL-4P
B8P-SHF
IL-G-3P
MAG
POWER SUPPLY CIRCUIT
CBD-1682A
1.+15V
2.+12V
3.+8V
4.GND
5.-15V
6.10V
7.10VE
8.+5V
1.MCT
2.MBK
3.HSP
4.HT ER
5. T IS TO P
6.C2
7.G ND
8.MPS
9.MIE R
2.1 A
1.2 A
2.1 A
1.2 A
2.1 A
1.2 A
1.MH
2.NC
3.MN
1.MH
2.NC
3.MN
1. X 1
2. X 2
No.2
No.1
2
1
4
35
6
FILTER
J1004 J1003
J 5J 4 J 3
J1001
J1002
J2102
J2101
J2103
ANTENNA
1.S H O R T
2.M AG I
3.X 1
4.X 2
5.T I
6.T IE
7.+15V
B9P-SHF B8P-SHF
1586514-2
350209-1
IL-10P
350209-2
350209-1
350428-1
MODULATOR
CIRCUIT
CPA-264
MODULATOR UNIT
INT ERC ONN ECTION
CMB-405
D.L
①②
③
①②
③
ﾐﾄﾞﾘ
ｷ
C201
0.01UF 1KV
C202
0.22UF 200V
R202
2.7KΩ
1/2W
C203
0.22UF
200V
T1
R201
150Ω
8W
H-7LPRD0122
CD202 CD201
MD-12N1MD-12N1
NJC3901M NJC3901M
Ａ101 Ａ102
P3001
P1109 P1110
P110 4
P1103 P1003
P1004
P1111
PULSE TRANS
W201
BLK.T
P3
P2103
P1118
DUMMY
A103
(W001)
(W003)
(W006)
P1002
1.+12V
2.GND
3.FAN_ERR2
J1114
IL-G-3P
1.+12V
2.C 2
J1105
IL-G-2P
P1105
MODULATOR UNIT
NMA-552
P8
TRANSCEIVER UNIT INTERCONNECTION
CMK-593
(W106)
(W103)
(W104)
(W105)
ZCRD1242※
ZCRD1244※
P1212
J1
IL-G-6P
J2
IL-G-4P
PTI
PTE
LVR
PMS
E
TXI
TXE
E
VERR
VD+
VD-
TRIG+
TRIG-
BP+
BP -/ BZ-
BZ+
MTRE
MTR-
MTR+
TB201 TB204
(W301)
ZCRD1248※
ZCRD1243※
(W302)
ZCRD1249※
Ａ301
NJS6930
PIN
Ａ302
NJS6926
ZCRD1234※
ZCRD1245※
ZCRD1233※
ZCRD1246※
ZCRD1235※
(W004)
(W005)
ZCRD1236※
ZCRD1237※
1.φ Z
2.φZE
3.φA
4.φ B
5.+12V
6.GND
J13
IL-6P
50/60ｋW
BLK
RED
BLK
RED
U1
V1
U0
V0
U1
U0
V1
V0
+12V
C2
φZE
φZ
φA
E
φB
+48V
+48V
+48VG
RED.T
WHT.T
RED
WHT
(W008) ZCRD1239※
ANTENNA
ANTENNA
DISPLAY UNIT
ANTENNA DISPLAY
UNIT
(W203) ZCRD1247※
(W007) ZCRD1238※
HC3L2
3L1
3L1
3L2
TB203
TB202
P2101
P2102
P101
8.GND
(W014)
ZCRD1241※
1.M+
2.M-
(W013) ZCRD1240※
1586514-2
NJC4002
9.NC
10.NC
B02P-NV(LF)(SN）
S.G.
S. G .S.G.
8.G N D
DISPLAY UNIT
(W303) ZCRD1483※
RELAY FILTER CIRCUIT
CSC-656
PC1201
IL - 3P
1.HMCNT
2.+15V
3.GND
P1211
P1202
1.MU2
J1212
1.VERR
2.E
3.MV2
J1202
J1201
J1211
1.U1
3.V1
2.NC
4.NC
2.GND
B4P-VH
B3P-NV
IL-3P
IL-2P
P1201
S.G.
M1568BS
Ｖ101
NJC9952
Ａ104
CFR-22 9
MAG FILTER
CIRCUIT
S.G.
220pF×5
+48VG
H-7 ZCRD####*:
“#” means specifi cation document No.
“*” mea ns revisi on of the specfication document.
JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner Unit
B－27
B
B.6.8 NKE-1130 (AC110V)
Fig B-24: Interconnection Diagram of NKE-1130 (AC110V)
NKE-1130PM （AC100V)
空中線機内接続図
1.TGT
2.TGTE
3.TNL
4.-15V
5.TNI
6.+15V
7.GN D
1. BS 3
2. BS 2
3. BS 1
4. T NC
5.MPS
6.VDE
7.VD
RECEIVER UNIT NRG-229
IF CIRCUIT CAE-499
J101
IL-9P
J102
IL-7P
T/R CONTROL CIRCUIT
CMC-1205R
1.MONI
2.GS
3.GSE
4.TGT
5.TGTE
6.TNL
7.-15V
8.TNI
9.+15V
10.GND
11.TRG2
1.BS3
2. BS 2
3. BS 1
4. T NC
5. M ic P S
6.VDINE
7.VDIN
8.+5V
1.RXD
2.TXD
3.+5V
4.GND
1. S HO RT
2.MAGI
3. X 1
4. X 2
5. T I
6. T IE
7.+15V
8.GND
9.NC
10.NC
11.NC
12.NC
1.HMCN T
2.+15V
3.GND
1.+15V
2.+12V
3.G ND
4.G ND
5.-15V
6.10V
7.10VE
8.+5V
1.MCT
2.MBK
3. T IS TO P
4.GND
5.MPS
6.MIE R
1.TIY
2.TIYE
3.BP
4.BPE
5.BZ
6.BZE
1.+12V
2.GND
3.FAN_ERR1
1.HTER1
2.HVGA T E 1
3.TISTOP1
4.GND
5.CN T
6.+5V
7.+15V
8.STABY_REQ
9.NC
1.PW1
2.PW2
3.PW3
4.+24V
5.GND
1.PTI
2.PTE
3.LVR
4.PMS
5.GN D
6.TXI
7.TXE
8.NC
1. BP +
2. BP -
3.BZ +
4.BZ -
5.TRIG+
6.TRIG-
7.MTR+
8.MTR-
9. MT R E
10.VD+
11.VD-
1.VD
2.VDE
3. MT R +
4. MT R -
J1118J1103J1104 J1111
J1191
J1110J1109
TB101
J8 J1106
J1112 J1113
IL-G-12P
IL-8P
IL -G -8P IL-G-11P
B6P-SHF
IL-G-9P
MSTBA2.5/11-G
IL- G -5P
B3P-SHF
IL-4P
B8P-SHF
IL -G -3 P
MAG
POWER SUPPLY
CIRCUIT
CBD-1682A
1.+15V
2.+12V
3.+8V
4.GND
5.-15V
6.10V
7.10VE
8.+5V
1.MCT
2.MBK
3.HSP
4.HTER
5.TISTOP
6.C2
7.GND
8.MPS
9.MIER
2.1A
1.2A
2.1A
1.2A
2.1A
1.2A
1.MH
2.NC
3.MN
1.MH
2.NC
3.MN
1.X1
2.X2
No.2
No.1
2
1
4
35
6
FILTER
J1004 J1003
J 5J 4 J 3
J1002
J2102
J2101
J2103
ANTTENA
1. S HO R T
2.MAG I
3. X 1
4. X 2
5. T I
6. T IE
7.+15V
8.GND
9.NC
10.NC
B9P-SHF B8P-SHF
B02P-NV(LF)(SN）
350209-1
IL-10P
350209-2
350209-1
MODULATOR
CIRCUIT
CPA-264
MODULATOR UNIT
INTERCONNECTION
CMB-406
D.L
①
②③
①
②
③
GRN
YEL
C201
0.01UF 1KV
C202
0.22 U F 2 00 V
R202
2.7KΩ
1/2W
C203
0.22UF
200V
T201
R２01
150Ω
8W
H-7LPRD0122
CD202 CD201
MD-12N1MD-12N1
NJC3316
Ａ101
M1555
Ｖ101
R ECEIRVER UNIT
INTERCONN ECTION
P3001 P3002
P1109 P1110
P1104
P1103 P1003
P1004
P1111
PULSE
TRANS
（W201)
BLK.T
P3
P2103
P1118
DUMMY
Ａ102
H-7ANRD0018
(W001) (W002)
(W003)
(W006)
P1002
1.+12V
2.GND
3.FAN_ERR2
J1114
IL-G-3P
1.+12V
2.C2
J1105
IL-G-2P
P1105
MODULATOR UNIT
NMA-551
SCANNER INTERCONNECTION
CAX-13
(W106)
ZCRD1321※
(W103)
ZCRD1318※
(W104)
ZCRD 1319※
(W105)
ZCRD1320※
ZCRD1267※
J1
IL-G-6P
J2
IL-G-4P
Ａ301
NJS6318
ZCRD1268※
CMA-902
ZCRD1266※
ZCRD1273※
ZCRD1269※
（W004）
(W005)
ZCRD1270※
ZCRD1271※
50/60ｋW
P2101
P2102
8.+5V
9.NC
RF CIRCUIT
CAF-595
J1001
350428-1
1.M+
2.M-
1586514-2
1586514-2
S.G.
S.G. S.G.
1.φZ
2.φZE
3.φ A
4.φB
5.+12V
6.GND
J13
IL-6P
SE
YE L
BLK
BLU
WHT
RED
SH I ELD
B102
ENCODER CHT-71A
P13
(W017)
DISPLAY UNIT
FAN
RED
BLU
YEL
B104
B103 FAN
(W010)
P1113 P1114
(W301)
TB102
S101
S-32F
23
9
56
8
SAFETY SWITCH
CSD-656
(W203)
ZCRD1274※
RED
WHT
RED
BLU
YEL
ZCRD1272※
P1112
J1112
1.PTI
2.PTE
1.LVR
2.PMS
3.E
3.TXI
4.TXE
J82
J81
PM
P81
P82
WHT
BLK
BLU
RED
BLK
WHT
BRN
NJU-84
7Z CRD1 27 9 ※
(W018)
ZCRD1275※
(W008)
ZCRD1283※
S. G.
S30kw, 2ﾕﾆｯﾄ
RED.T
RED.T
BLK.T
BLK.T
ZCRD1322※
(W302)
ZCRD1453※
S.G.
CFR-229
MAG FILTER
CIRCUIT
22 0pF ×5
P1201
+48V
+48VG
U1
V1
W1
U1
W1
V1
DISPLAY UNIT
+48V
+48VG
1
2
V
U
1
2
3
4
3
4
V
U
UTHUTH
TH101
TR101
（200W）
HEATER CONTROL PART
CHG-215
(OPTION)
WHT.T
WHT.T
W401 7ZCRD1509
to CMC-1205R J1112
(W308)
ZCRD1542※
WHT
BLK
BLU
MOTOR DRIVER
CBD-2001
ZC RD 145 6※
(W305)
P1212
BRAKE CIRCUIT
CFA-255
J1501
1.V ERR
2.E
H-7EPRD0035B201
J1505
PC1501
P1501
B2P-VH
P1505
RELAY FILTER
CIRCUIT
CSC-656
PC1201
IL-3P
1.HMCNT
2.+15V
3.GND
P1211
P1202
1.MU2
J1212
1.VERR1
2.E
3.MV2
J1202
J1201
J1211
1.U1
3.V1
2.NC
4.NC
2.G N D
B4P-VH
B3P-NV
IL-3P
IL-2P
1.VERR1
2.E
1.VERR
2.E
1.P
2.NC
3.N
1. P
2. N
1.BKH1
3. BK H 2
1.BKS1
2.BKS2
1.+15V
2.NC
3.+15VE
P1941 J1941
J1903
P1903
J1905
P1905
J1912
P1912
BRAKE CONTROL CIRCUIT
CCB-655
P1502
J1921
P1921
J1911
P1911
1.RE D
3. BL K
J1511
P1511
IL-2P
S3B-XH-A
1-350210-0 1-350209-0
1-480700-0
ZCRD1542※
(W308)
ZCRD1545※
(W311) ZCRD1541※
(W307)
ZCRD1284※
(W303)
AC100V
WC1
ZCRD1543※
(W309)
ZCRD1544※
(W310)
BLAKE CIR CUI T B
CFA-262
BRAKE CIRCUIT A
CFA-261
R1
R2
R3
R4
R1
120Ω
30W
330Ω
30W
×4
×1
2.NC
4.NC
1. S 1
2.S2
3.S3
4. S 4
5.S5
6.S6
J1502
J1503
3.M2
1.M1
5.M3
P1503
MOTOR
MOTOR
B101
CBP-205
H-7BDRD0049
2.NC
(W304)
ZCRD1316※
R1
R2
1.2kΩ
30W
P1504
1.R 1
3.R2
J1504
B3P-VH
2.NC
3.M V 2
1.M U2
2.N C
4.NC
5.N C
6.G N D
B6P-VH
to CCB-655 J1941
B－28
JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner Unit
B.6.9 NKE-1130 (AC220V)
Fig B-25: Interconnection Diagram of NKE-1130 (AC220V)
NKE-1130PM （AC220V)
空中線機内接続図
1.TGT
2.TGTE
3.TNL
4.-15V
5.TNI
6.+15V
7.GN D
1. BS 3
2. BS 2
3. BS 1
4. T NC
5.MPS
6.VDE
7.VD
RECEIVER UNIT NRG-229
IF CIRCUIT CAE-499
J101
IL-9P
J102
IL-7P
T/R CONTROL CIRCUIT
CMC-1205R
1.MONI
2.GS
3.GSE
4.TGT
5.TGTE
6.TNL
7.-15V
8.TNI
9.+15V
10.GND
11.TRG2
1.BS3
2. BS 2
3. BS 1
4. T NC
5. M ic P S
6.VDINE
7.VDIN
8.+5V
1.RXD
2.TXD
3.+5V
4.GND
1. S HO RT
2.MAGI
3. X 1
4. X 2
5. T I
6. T IE
7.+15V
8.GND
9.NC
10.NC
11.NC
12.NC
1.HMCN T
2.+15V
3.GND
1.+15V
2.+12V
3.G ND
4.G ND
5.-15V
6.10V
7.10VE
8.+5V
1.MCT
2.MBK
3. T IS TO P
4.GND
5.MPS
6.MIE R
1.TIY
2.TIYE
3.BP
4.BPE
5.BZ
6.BZE
1.+12V
2.GND
3.FAN_ERR1
1.HTER1
2.HVGA T E 1
3.TISTOP1
4.GND
5.CN T
6.+5V
7.+15V
8.STABY_REQ
9.NC
1.PW1
2.PW2
3.PW3
4.+24V
5.GND
1.PTI
2.PTE
3.LVR
4.PMS
5.GN D
6.TXI
7.TXE
8.NC
1. BP +
2. BP -
3.BZ +
4.BZ -
5.TRIG+
6.TRIG-
7.MTR+
8.MTR-
9. MT R E
10.VD+
11.VD-
1.VD
2.VDE
3. MT R +
4. MT R -
J1118J1103J1104 J1111
J1191
J1110J1109
TB101
J8 J1106
J1112 J1113
IL-G-12P
IL-8P
IL -G -8P IL-G-11P
B6P-SHF
IL-G-9P
MSTBA2.5/11-G
IL- G -5P
B3P-SHF
IL-4P
B8P-SHF
IL -G -3 P
MAG
POWER SUPPLY
CIRCUIT
CBD-1682A
1.+15V
2.+12V
3.+8V
4.GND
5.-15V
6.10V
7.10VE
8.+5V
1.MCT
2.MBK
3.HSP
4.HTER
5.TISTOP
6.C2
7.GND
8.MPS
9.MIER
2.1A
1.2A
2.1A
1.2A
2.1A
1.2A
1.MH
2.NC
3.MN
1.MH
2.NC
3.MN
1.X1
2.X2
No.2
No.1
2
1
4
35
6
FILTER
J1004 J1003
J 5J 4 J 3
J1002
J2102
J2101
J2103
ANTTENA
1. S HO R T
2.MAG I
3. X 1
4. X 2
5. T I
6. T IE
7.+15V
8.GND
9.NC
10.NC
B9P-SHF B8P-SHF
B02P-NV(LF)(SN）
350209-1
IL-10P
350209-2
350209-1
MODULATOR
CIRCUIT
CPA-264
MODULATOR UNIT
INTERCONNECTION
CMB-406
D.L
①
②③
①
②
③
GRN
YEL
C201
0.01UF 1KV
C202
0.22 U F 2 00 V
R202
2.7KΩ
1/2W
C203
0.22UF
200V
T201
R２01
150Ω
8W
H-7LPRD0122
CD202 CD201
MD-12N1MD-12N1
NJC3316
Ａ101
M1555
Ｖ101
R ECEIRVER UNIT
INTERCONN ECTION
P3001 P3002
P1109 P1110
P1104
P1103 P1003
P1004
P1111
PULSE
TRANS
（W201)
BLK.T
P3
P2103
P1118
DUMMY
Ａ102
H-7ANRD0018
(W001) (W002)
(W003)
(W006)
P1002
1.+12V
2.GND
3.FAN_ERR2
J1114
IL-G-3P
1.+12V
2.C2
J1105
IL-G-2P
P1105
MODULATOR UNIT
NMA-551
SCANNER INTERCONNECTION
CAX-13
(W106)
ZCRD1321※
(W103)
ZCRD1318※
(W104)
ZCRD 1319※
(W105)
ZCRD1320※
ZCRD1267※
J1
IL-G-6P
J2
IL-G-4P
Ａ301
NJS6318
ZCRD1268※
CMA-902
ZCRD1266※
ZCRD1273※
ZCRD1269※
（W004）
(W005)
ZCRD1270※
ZCRD1271※
50/60ｋW
P2101
P2102
8.+5V
9.NC
RF CIRCUIT
CAF-595
J1001
350428-1
1.M+
2.M-
1586514-2
1586514-2
S.G.
S.G. S.G.
1.φZ
2.φZE
3.φ A
4.φB
5.+12V
6.GND
J13
IL-6P
SE
YE L
BLK
BLU
WHT
RED
SH I ELD
B102
ENCODER CHT-71A
P13
(W017)
DISPLAY UNIT
FAN
RED
BLU
YEL
B104
B103 FAN
(W010)
P1113 P1114
(W301)
TB102
S101
S-32F
23
9
56
8
SAFETY SWITCH
CSD-656
(W203)
ZCRD1274※
RED
WHT
RED
BLU
YEL
ZCRD1272※
P1112
J1112
1.PTI
2.PTE
1.LVR
2.PMS
3.E
3.TXI
4.TXE
J82
J81
PM
P81
P82
WHT
BLK
BLU
RED
BLK
WHT
BRN
NJU-84
7Z CRD1 27 9 ※
(W018)
ZCRD1275※
(W008)
ZCRD1283※
S. G.
S30kw, 2ﾕﾆｯﾄ
RED.T
RED.T
BLK.T
BLK.T
ZCRD1322※
(W302)
ZCRD1453※
S.G.
CFR-229
MAG FILTER
CIRCUIT
22 0pF ×5
P1201
+48V
+48VG
U1
V1
W1
U1
W1
V1
DISPLAY UNIT
+48V
+48VG
1
2
V
U
1
2
3
4
3
4
V
U
UTHUTH
TH101
TR101
（200W）
HEATER CONTROL PART
CHG-215
(OPTION)
WHT.T
WHT.T
W401 7ZCRD1509
to CMC-1205R J1112
WHT
BLK
BLU
MOTOR DRIVER
CBD-2000
ZC RD 145 6※
(W305)
P1212
BRAKE CIRCUIT
CFA-255
J1501
1.V ERR
2.E
H-7EPRD0034B201
J1505
PC1501
P1501
B2P-VH
P1505
RELAY FILTER
CIRCUIT
CSC-656
PC1201
IL-3P
1.HMCNT
2.+15V
3.GND
P1211
P1202
1.MU2
J1212
1.VERR1
2.E
3.MV2
J1202
J1201
J1211
1.U1
3.V1
2.NC
4.NC
2.G N D
B4P-VH
B3P-NV
IL-3P
IL-2P
1.VERR1
2.E
1.VERR
2.E
1.P
2.NC
3.N
1. P
2. N
1. BK H 1
3. BK H 2
1.BKS1
2.BKS2
1.+15V
2.NC
3.+15VE
P1941 J1941
J1903
P1903
J1905
P1905
J1912
P1912
BRAKE CONTROL CIRCUIT
CCB-655
P1502
J1921
P1921
J1911
P1911
1.RE D
3. BL K
J1511
P1511
IL-2P
S3B-XH-A
1-350210-0 1-350209-0
1-480700-0
ZCRD1542※
(W308)
ZCRD1545※
(W311) ZCRD1541※
(W307)
ZCRD1284※
(W303)
AC220V
WC1
ZCRD1543※
(W309)
ZCRD1544※
(W310)
BLAKE CIR CUI T B
CFA-262
BRAKE CIRCUIT A
CFA-261
R1
R2
R3
R4
R1
120Ω
30W
330Ω
30W
×4
×1
2.NC
4.NC
1. S 1
2.S2
3.S3
4. S 4
5.S5
6.S6
J1502
J1503
3.M2
1.M1
5.M3
P1503
MOTOR
MOTOR
B101
CBP-205
H-7BDRD0049
2.NC
(W304)
ZCRD1316※
R1
R2
1.2kΩ
30W
P1504
1.R 1
3.R2
J1504
B3P-VH
2.NC
3.M V 2
1.M U2
2.N C
4.NC
5.N C
6.G N D
B6P-VH
to CCB-655 J1941
(W308)
ZCRD1542※
JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner Unit
B－29
B
B.6.10 NKE-1139 (AC110V)
Fig B-26: Interconnection Diagram of NKE-1139 (AC110V)
NKE-1139PM (AC100V)
空中線機内接続図
SCANNER INTERCONNECTION
CAX-14
U1
V1
S101
S-32
23
9
56
8
RED.T
BLK.T
（W301) ZCRD1287※ RED WHT
RED.T
BLK.T
（W302) ZCRD1288※
SAFETY SWITCH CSD-657
HEATER CONTROL
PART
CHG-215
(OPTION)
TRANSCEIVER UNIT
WHT
+12V
C2
ΦZE
ΦZ
ΦA
E
ΦB
RED
SHIELD
YEL
BLU
WHT
SE
B1 02
ENCODER CHT-71A1
C102C101
2200p
50V
1000μ
16V
+
BLK
TB103
BLK
BLK
AC100V
UTH
U
V
TH101
TR101
（100W）
WHT.T
TXI
TXE
VERR1
E
LVR
PMS
E
TB104
RED
S.G.S.G.
S.G.
Sﾊﾞﾝﾄﾞ, 3ﾕﾆｯﾄ
（W305) ZCRD1457※
PTE
PTI
W401 7ZCRD1509
WHT.T
J82
J81 P81
P82
WHT
BLK
BLU
RE D
BLK
WHT
BRN
1
1
PM
NJU-84
ZCRD1179※
（W303) ZCRD1276※
S.G.
TRANSCEIVER UNIT TRANSCEIVER UNIT
1.VERR1
2.E
1.VERR
2.E
1.P
2.NC
3.N 1.BKH1
3.BKH2
1.BKS1
2.BKS2
1.+12V
2.NC
3.+12VE
P1941 J1941
J1903
P1903
J1905
P1905
J1912
P1912
BRAKE CONTROL CIRCUIT
CCB-655
J1921
P1921
J1911
P1911
1.RED
3.BLK
IL-2P
B2PS-VH
S3B-XH-A
1-350210-0 1-350209-0
ZCRD1553※
ZCRD1552※
(W307)
ZCRD1543※
(W309)
ZCRD1544※
(W310)
CBD-2001
(W304)
ZCRD 1316※
BRAKE CIRCUIT
CFA-255
R1R2
1.2kΩ
30W
1.2kΩ
30W
P1504
J1501
1.R1
3.R2
H-7EPRD0035B201
J1504
J1505
PC1501
P1501
B3P-VH
2.NC
B2P-VH
1.P
2.N
P1502
AC100V
WC 1
CBP-205
H-7BDRD0049
2.NC
4.NC
1.S1
2.S2
3.S3
4.S4
5.S5
6.S6
J1502
J1503
3.M2
1.M1
5.M3
P1503
MOTOR
MOTO R
B101
(W308)
MOTOR DRIVER
BRA KE C IRCUIT B
CFA-262
BRAKE CIRCUIT A
CFA-261
R1
R2
R3
R4
R1
120Ω
30W
330Ω
30W
×4
×1
2.NC
3.MV2
1.MU2
2.NC
4.NC
5.NC
6.GND
B6P-VH
1.VERR
2.E
B－30
JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner Unit
B.6.11 NKE-1139 (AC220V)
Fig B-27: Interconnection Diagram of NKE-1139 (AC220V)
NKE-1139PM (AC220V)
空中線機内接続図
SCANNER INTERCONNECTION
CAX-14
U1
V1
S101
S-32
23
9
56
8
RED.T
BLK.T
（W301) ZCRD1287※ RED WHT
RED.T
BLK.T
（W302) ZCRD1288※
SAFETY SWITCH CSD-657
HEATER CONTROL
PART
CHG-215
(OPTION)
TRANSCEIVER UNIT
WHT
+12V
C2
ΦZE
ΦZ
ΦA
E
ΦB
RED
SHIELD
YEL
BLU
WHT
SE
B1 02
ENCODER CHT-71A1
C102C101
2200p
50V
1000μ
16V
+
BLK
TB103
BLK
BLK
AC100V
UTH
U
V
TH101
TR101
（100W）
WHT.T
TXI
TXE
VERR1
E
LVR
PMS
E
TB104
RED
S.G.S.G.
S.G.
Sﾊﾞﾝﾄﾞ, 3ﾕﾆｯﾄ
（W305) ZCRD1457※
PTE
PTI
W401 7ZCRD1509
WHT.T
J82
J81 P81
P82
WHT
BLK
BLU
RE D
BLK
WHT
BRN
1
1
PM
NJU-84
ZCRD1179※
（W303) ZCRD1276※
S.G.
TRANSCEIVER UNIT TRANSCEIVER UNIT
1.VERR
2.E
1.VERR
2.E
1.P
2.NC
3.N 1.B K H 1
3.BKH2
1.BKS1
2.BKS2
1.+12V
2.NC
3.+12VE
P1941 J1941
J1903
P1903
J1905
P1905
J1912
P1912
BRAKE CONTROL CIRCUIT
CCB-655
J1921
P1921
J1911
P1911
1.RED
3.BLK
IL-2P
B2PS-VH
S3B-XH-A
1-350210-0 1-350209-0
ZCRD1553※
ZCRD1552※
(W307)
ZCRD1543※
(W309)
ZCRD1544※
(W310)
CBD-2000
(W304)
ZCRD 1316※
BRAKE CIRCUIT
CFA-255
R1R2
1.2kΩ
30W
1.2kΩ
30W
P1504
J1501
1.R1
3.R2
H-7EPRD0034B201
J1504
J1505
PC1501
P1501
B3P-VH
2.NC
B2P-VH
1.P
2.N
P1502
AC220V
WC 1
CBP-205
H-7BDRD0049
2.NC
4.NC
1.S1
2.S2
3.S3
4.S4
5.S5
6.S6
J1502
J1503
3.M2
1.M1
5.M3
P1503
MOTOR
MOTO R
B101
(W308)
MOTOR DRIVER
BRA KE C IRCUIT B
CFA-262
BRAKE CIRCUIT A
CFA-261
R1
R2
R3
R4
R1
120Ω
30W
330Ω
30W
×4
×1
2.NC
3.MV2
1.MU2
2.NC
4.NC
5.NC
6.GND
B6P-VH
1.VERR
2.E
JMA-9100 Instruction Manual > B.DRAWINGS > B.6 Interconnection Diagram of Scanner Unit
B－31
B
B.6.12 NTG-3230
Fig B-28: Interconnection Diagram of NTG-3230
NTG-3230
送受信機機内接続図
1.TGT
2.TGTE
3.TNL
4.-15V
5.TNI
6.+15V
7.GND
1.BS3
2.BS2
3.BS1
4.TNC
5.MPS
6.VDE
7.VD
RECEIVER UNIT NRG-229
IF CIRCUIT CAE-499
J101
IL-9P
J102
IL-7P
T/R CONTROL CIRCUIT
CMC-1205R
1.MONI
2.GS
3.GSE
4.TGT
5.TGTE
6.TNL
7.-15V
8.TNI
9.+15V
10.GND
11.TRG2
1.BS 3
2.BS 2
3.BS 1
4.TNC
5.MicPS
6.VDINE
7.VDIN
8.+5V
1.RXD
2.TXD
3.+5V
4.GND
1.SHORT
2.MAGI
3.X1
4.X2
5.TI
6.TIE
7.+15V
8.GND
9.NC
10.NC
11.NC
12.NC
1.HMCNT
2.+15V
3.GND
1.+15V
2.+12V
3.GND
4.GND
5.-15V
6.10V
7.10VE
8.+5V
1.MCT
2.MBK
3.TISTOP
4.GND
5.MPS
6.MIER
1.TIY
2.TI YE
3.BP
4.B P E
5.BZ
6.B Z E
1.+12V
2.GND
3.FAN_ERR1
1. HT E R1
2. HV GA T E1
3. T IS T O P1
4.GND
5.CN T
6.+5V
7.+15V
8. S T A BY _R E Q
9.NC
1.PW1
2.PW2
3.PW3
4.+24V
5.GND
1.PTI
2.PTE
3.LVR
4.PMS
5.GND
6.TXI
7.TXE
8.NC
1.BP+
2.BP-
3.BZ+
4.BZ-
5.TRIG+
6.TRIG-
7.MTR+
8.MTR-
9.MTRE
10.VD+
11.VD-
1.VD
2.VDE
3.MTR+
4.MTR-
J1118
J1103J1104 J1111
J1191
J1110J1109
TB101
J8 J1106
J1112 J1113
IL-G-12P
IL-8P
IL-G-8P IL-G -11P
B6P-SHF
IL -G -9P
MSTBA2.5/11-G
IL-G-5P
B3P-SHF
IL-4P
B8P-SHF
IL-G-3P
MAG
POWER SUPPLY CIRCUIT
CBD-1682A
1.+15V
2.+12V
3.+8V
4.G ND
5.-15V
6.10V
7.10VE
8.+5V
1.MCT
2.MBK
3.HSP
4.HTER
5 .TI ST OP
6.C2
7.GND
8.MPS
9.MIER
2.1A
1.2A
2.1A
1.2A
2.1A
1.2A
1.MH
2.NC
3.MN
1.MH
2.NC
3.MN
1.X1
2.X2
No.2
No.1
2
1
4
35
6
FILTER
J1004 J1003
J 5J 4 J 3
J1002
J2102
J2101
J2103
ANTENNA
1.SHORT
2.MAGI
3.X1
4.X2
5.TI
6.TIE
7.+15V
8.G N D
9.NC
10.NC
B9P-SHF B8P-SHF
B02P-NV(LF)(SN）
350209-1
IL-10P
350209-2
350209-1
MODULATOR CIRCUIT
CPA-264
MODULATOR UNIT
INTERCONNECTION
CMB-407
TRHPL
①
③
②①
③
GRN
C201
0.01UF 1KV
C202
0.22UF 200V
R202
2.7KΩ
1/2W
C203
0.22UF
200V
T1
R201
150Ω
8W
H-7LPRD0122
CD202 CD201
MD-12N1MD-12N1
NJC3317
Ａ201
M1555
Ｖ101
RECEIVER UNIT
INTERCONNECTION
P3001 P3002
P1109 P1110
P1104
P1103 P1003
P1004
P1111
PUL S E TRANS
W201
BLK.T
P3
P2103
P1118
DUMMY
Ａ205
(W001) (W002)
(W003)
(W006)
P1002
1.+12V
2.GND
3.FAN_ERR2
J1114
IL-G-3P
1.+12V
2.C 2
J1105
IL-G-2P
P1105
MODULATOR UNIT
NMA-553
P8
TRANSCEIVER UNIT INTERCONNECTION
CMK-594
(W106)
(W103)
(W104)
(W105)
ZCRD1218※
ZCRD1227※
ZCRD1229※
P1201
J1 IL-G-6P
J2 IL-G-4P
PTI
PTE
LVR
PMS
E
TXI
TXE
E
VERR
VD+
VD-
TRIG+
TRIG-
BP+
BP -/ BZ -
BZ+
MTRE
MTR-
MTR+
TB201 TB204
(W301)
ZCRD1215※
ZCRD1228※
(W302)
ZCRD1216※
Ａ203
TL378A
ZCRD1219※
ZCRD1230※
CMA-902
ZCRD1217※
ZCRD1231※
ZCRD1220※
（W004）
(W005)
ZCRD1221※
ZCRD1222※
1.φZ
2.φZE
3.φA
4.φB
5.+12V
6.GND
J13
IL-6P
BLK
RED
BLK
RED
+12V
C2
φZE
φZ
φA
GND
φB
+48VG
+48V
+48V
+48VG
RED.T
WHT.T
RED
WHT
(W008) ZCRD1224※
SCANNER
UNIT
SCANNER UNITDISPLAY UNIT
SCANNER
UNIT
DISPLAY
UNIT
(W203) ZCRD1232※
(W007) ZCRD1223※
HC3L2
3L1
3L1
3L2
TB203
TB202
P2101
P2102
P101
8.+5V
9.NC
RF CIRCUIT
CAF-595
(W014)
ZCRD1226※
J1001
350428-1
1.M+
2.M-
1586514-2
(W013) ZCRD1225※
1586514-2
S.G.
S.G. S . G.
U1
V1
U0
V0
U1
U0
V1
V0
DISPLAY
UNIT
H-7ANRD0018
②
(W303) ZCRD1484※
RELAY FILTER CIRCUIT
CSC-656
PC1201
IL-3P
1.H MCN T
2.+15V
3.G N D
P1211
P1202
1.MU2
J1212
1.VERR
2.E
3.MV2
J1202
J1201
J1211
1.U1
3.V1
2.N C
4.N C
2.GND
B4P-VH
B3P-NV
IL-3P
IL-2P
P1212
S. G.
CFR-229
MAG FILTER CIRCUIT
220pF×5
YEL
S.G.
H-7 ZCRD#### *:
“#” means specif icatio n document No.
“*” means revision of the sp ecfication document.
JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection Diagram
B－33
B
B.7.1 JMA-9110-6XA/JMA-9110-6XAH
Fig B-29: Terminal Board Connection Diagram of JMA-9110-6XA/JMA-9110-6XAH
1VD+
2VD-
3TRIG+
4TRIG-
5BP+
6BP-
7BZ+
8BZ-
9MTR+
10 MTR-
11 MTRE
12 (NC)
13 +48 V
14 +48 VG
TB4101(ANT)
1NA V1 TX+
2NA V1 TX-
3NA V1 RX+
4NA V1 RX-
5NA V2 TX+
6NA V2 TX-
7NA V2 RX+
8NA V2 RX-
9LO G RX +
10 LO G RX -
11 ALMTX+
12 ALMTX-
13 ALMRX+
14 ALMRX-
15 ARPAT X+
16 ARPAT X-
17 JAR PA TX+
18 JAR PA TX-
19 NSKT X+
20 NSKT X-
21 HDG RX+
22 HDG RX-
TB4501(OPTION) 1ARPAALM+
2ARPAALM-
3SYSALM+
4SYSALM+
5PWRALM+
6PWRALM-
7ARPAAC K+
8ARPAAC K-
9SYSACK+
10 SYSACK-
11 PWRACK+
12 PWRACK-
13 EXEVT+
14 EXEVT-
15 AISTX+
16 AISTX-
17 AIS_TG
18 AISRX+
19 AISRX-
20 AIS_RG
21 MNTTX+
22 MNTTX-
TB4601(ALARM) TB4401(EXT RADAR)
1RBVD
2RBVDE
3ETIY3
4ETIY3E
5SVD1
6SVD1E
7ETIY1
8ETIY1E
9EXφA1
10 EXφA1E
11 EXφB1
12 EXφB1E
13 EXφZ1
14 EXφZ1E
15
16
17
18
19
20
21
22
23
24
25 (NC)
26 (NC)
27 ACKOUT+
28 ACKOUT-
29 WMRST+
30 WMRST-
SVD2
SVD2E
ETIY2
ETIY2E
EXφA2
EXφA2E
EXφB2
EXφB2E
EXφZ2
EXφZ2E
1(NC)
2
3
4
5P1+
6P1-
7
8
9S1+
10 S2-
11
12
TB4801(LOG)
(NC)
(NC)
(NC)
(NC)
(NC)
(NC)
(NC) U
W
V
FILTER ACIN
1 U
2 V
3FG
CBD-1684A TB521
1 +
2ー
3FG
CBD-1684A TB522
CDC-1324
J4409(DSUB-15P)
R
CQD-1891
(JRC SUPPLY)
G
B
H
V
RED
GRN
BLU
GR Y
BLK
11/R1
22/S1
33/S2
4S3
55/R2
6(NC)
TB4701(GYRO)
2A
1A
J4
J5
J2
2A
1A
VD
VDE
COM+
COM-
2A
1A
J3
J1
ETIY
AGND
EXBP
AGND
EXBZ
AGND
PTI
PTE
TXI
TXE
LVR
PMS
E
P82
P81
PTI
PTE
TXI
TXE
LVR
PMS
E
P2
P1
SCANNER UNIT
NKE-2103-6/6HS
PERFORMANCE
MONITOR
NJU-85
DISPLAY UNIT NCD-4990
BLU
1
YE L
GRN
WHT-B LU
WHT-WH T
ORG
BLK
PNK
BR N
2
RED
PUR
WHT-YEL
WHT-WH T
H-2695111153
(JRC SUPPLY)
1VDIN1
2VDIN1E
3TRIGIN1
4TRIGIN1E
5BPIN1
6BPIN1E
7BZIN1
8BZIN1E
9MTRIN1+
10 MTRIN1-
11 MTRIN1E
12 PWRIN1
13 PWRIN1E
14 PWROUT1
15 PWROUT1E
16 VDOUT1
17 VDOUT1E
18 TRIGOUT1
19 TRIGOUT1E
20 BPOUT1
21 BPOUT1E
22 BZOUT1
23 BZOUT1E
24 MTROUT1+
25 MTROUT1-
26 MTROUT1E
TB4201(ISW IN/OUT)
RADAR
(INTERSWITC H)
WHT
RED
WH T
BLK
ECDIS
H-2695110006
(JRC SUPPLY)
250V-TTYCS-1
250V-TTYCS-1
CONNING
DISPLAY
VDR
3C-2V x5 (MAX 30m)
250V-TTYCS-1
250V-TTYCS-1
250V-TTYCS-1
250V-TTYCS-1
DGPS
ECHO
SOUNDER
LOG
(NMEA0183)
250V-TTYCS-4
AIS
0.6/1kV-DPYCYS-1.5
250V-MPYCYS-7
GYRO
LOG
(200P /NM)
0 . 6/ 1k V -D P YCY S- 1. 5
ALARM MONITORING
SYSTEM
(NEAREST APPROACH)
YEL.T/PNK.T
BLK.T/SKY.T
ORN
BLK
GRN
YEL
WHT
WHT.T/ O RN.T
RED.T/GRN.T
PUR.T/BRN.T
BLU.T/GRY.T
SHIP’S MAINS
AC100-115V/AC220-240V 50/60Hz 1φ
W406 H-7ZCRD1342 A
(Wiring is com pleted .)
(X-BAND 10kW RADAR)
JMA-9110-6XA/6XAH レーダー 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9110-6XA/6XAH
WHT
BLK
WHT
BRN
BLU
RED
BLK
WHT
BRN
BLU
RED
BLK
BLK . T/SKY .T
YE L .T/ PNK.T
ORN
GR N
BLK
WH T
YEL
PUR. T/ BRN.T
R ED .T/ GR N. T
WHT.T/ORN.T
BLU .T /G RY .T
19-CORES COMPOSITE CABLE (JRC SUPPLY)
CFQ-6912-**
CQD-2097 T ERMINAL BOARD
Wiring of PERFOR MAN CE MONITOR
is completed.
0.6/1kV-DPYCY-6
J4407
RJ-45 LAN
U
V
W
CBD-1661 ACOUT1
BATT IN -
BATT IN +
SH IE L D
COAXIAL
CO A XI AL
SHIELD
B－34
JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection Diagram
B.7.2 JMA-9110-6XA/JMA-9110-6XAH (desktop)
Fig B-30: Terminal Board Connection Diagram of JMA-9110-6XA/JMA-9110-6XAH (desktop)
1VD+
2VD-
3TRIG+
4TRIG-
5BP+
6BP-
7BZ+
8BZ-
9MTR+
10 MTR-
11 MTRE
12 (NC)
13 +48 V
14 +48 VG
TB4101(ANT)
1NA V1 TX+
2NA V1 TX-
3NA V1 RX+
4NA V1 RX-
5NA V2 TX+
6NA V2 TX-
7NA V2 RX+
8NA V2 RX-
9LO G RX +
10 LO G RX -
11 ALMTX+
12 ALMTX-
13 ALMRX+
14 ALMRX-
15 ARPAT X+
16 ARPAT X-
17 JAR PA TX+
18 JAR PA TX-
19 NSKT X+
20 NSKT X-
21 HDG RX+
22 HDG RX-
TB4501(OPTION) 1ARPAALM+
2ARPAALM-
3SYSALM+
4SYSALM+
5PWRALM+
6PWRALM-
7ARPAAC K+
8ARPAAC K-
9SYSACK+
10 SYSACK-
11 PWRACK+
12 PWRACK-
13 EXEVT+
14 EXEVT-
15 AISTX+
16 AISTX-
17 AIS_TG
18 AISRX+
19 AISRX-
20 AIS_RG
21 MNTTX+
22 MNTTX-
TB4601(ALARM) TB4401(EXT RADAR)
1RBVD
2RBVDE
3ETIY3
4ETIY3E
5SVD1
6SVD1E
7ETIY1
8ETIY1E
9EXφA1
10 EXφA1E
11 EXφB1
12 EXφB1E
13 EXφZ1
14 EXφZ1E
15
16
17
18
19
20
21
22
23
24
25 (NC)
26 (NC)
27 ACKOUT+
28 ACKOUT-
29 WMRST+
30 WMRST-
SVD2
SVD2E
ETIY2
ETIY2E
EXφA2
EXφA2E
EXφB2
EXφB2E
EXφZ2
EXφZ2E
1(NC)
2
3
4
5P1+
6P1-
7
8
9S1+
10 S2-
11
12
TB4801(LOG)
(NC)
(NC)
(NC)
(NC)
(NC)
(NC)
(NC) U
W
V
FILTER ACIN
1 +
2ー
3FG
TB401
CDC-1324
J4409(DSUB-15P)
R
CQD-1891
(JRC SUPPLY)
G
B
H
V
RED
GRN
BLU
GR Y
BLK
11/R1
22/S1
33/S2
4S3
55/R2
6(NC)
TB4701(GYRO)
2A
1A
J4
J5
J2
2A
1A
VD
VDE
COM+
COM-
2A
1A
J3
J1
ETIY
AGND
EXBP
AGND
EXBZ
AGND
PTI
PTE
TXI
TXE
LVR
PMS
E
P82
P81
PTI
PTE
TXI
TXE
LVR
PMS
E
P2
P1
SCANNER UNIT
NKE-2103-6/6HS
PERFORMANCE
MONITOR
NJU-85
DISPLAY UNIT NCD-4990T
BLU
1
YE L
GRN
WHT-B LU
WHT-WH T
ORG
BLK
PNK
BR N
2
RED
PUR
WHT-YEL
WHT-WH T
H-2695111153
(JRC SUPPLY)
1VDIN1
2VDIN1E
3TRIGIN1
4TRIGIN1E
5BPIN1
6BPIN1E
7BZIN1
8BZIN1E
9MTRIN1+
10 MTRIN1-
11 MTRIN1E
12 PWRIN1
13 PWRIN1E
14 PWROUT1
15 PWROUT1E
16 VDOUT1
17 VDOUT1E
18 TRIGOUT1
19 TRIGOUT1E
20 BPOUT1
21 BPOUT1E
22 BZOUT1
23 BZOUT1E
24 MTROUT1+
25 MTROUT1-
26 MTROUT1E
TB4201(ISW IN/OUT)
RADAR
(INTERSWITC H)
WHT
RED
WH T
BLK
ECDIS
H-2695110006
(JRC SUPPLY)
250V-TTYCS-1
250V-TTYCS-1
CONNING
DISPLAY
VDR
3C-2V x5 (MAX 30m)
250V-TTYCS-1
250V-TTYCS-1
250V-TTYCS-1
250V-TTYCS-1
DGPS
ECHO
SOUNDER
LOG
(NMEA0183)
250V-TTYCS-4
AIS
0.6/1kV-DPYCYS-1.5
250V-MPYCYS-7
GYRO
LOG
(200P /NM)
0.6/1kV-DPYCYS-1.5
ALARM MONITORING
SYSTEM
(NEAREST APPROACH)
YEL.T/PNK.T
BLK.T/SKY.T
ORN
BLK
GRN
YEL
WHT
WHT.T/ O RN.T
RED.T/GRN.T
PUR.T/BRN.T
BLU.T/GRY.T
SHIP’S MAINS
AC100-115V/AC220-240V 50/60Hz 1φ
W407 H-7ZCRD1343 A
(JRC SUPPLY)
(X-BAND 10kW RADAR)
JMA-9110-6XA/6XAH レーダー（卓上型） 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9110-6XA/6XAH(desktop)
WHT
BLK
WHT
BRN
BLU
RED
BLK
WHT
BRN
BLU
RED
BLK
BLK . T/SKY .T
YE L .T/ PNK.T
ORN
GR N
BLK
WH T
YEL
PUR. T/ BRN.T
R ED .T/ GR N. T
WHT.T/ORN.T
BLU .T /G RY .T
19-CORES COMPOSITE CABLE (JRC SUPPLY)
CFQ-6912-**
CQD-2097 T ERMINAL BOARD
Wiring of PERFOR MAN CE MONITOR
is completed.
1 U
2 V
3 W
TB402
W405 H-7ZC RD1341A(JRC SUPPLY)
Wiring is completed.
1 U
2 V
3FG
CBD-1684A TB 521
W408 H-7ZCRD1344 A
(JRC SUPPLY)
WHT
BLK
GRN
GR N
BLK- BL K
WH T- B LK
1 +
2ー
3FG
CBD-1684A TB 522
AC/DC CONVERTER UNIT
NBA-5135
GRN
BLK
WHT
GRN
BLK-BLK
WHT-BLK
WHT
BLK
RED
RED
WHT
BLK
0.6/1kV-DPYCY-6
J4407
RJ-45 LAN
U
V
W
CBD-1661 ACOUT1
BATT IN -
BATT IN +
SH IE L D
COAXIAL
CO A XI AL
SHIELD
JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection Diagram
B－35
B
B.7.3 JMA-9122-6XAH
Fig B-31: Terminal Board Connection Diagram of JMA-9122-6XAH
1VD+
2VD-
3TRIG+
4TRIG-
5BP+
6BP-
7BZ+
8BZ-
9MTR+
10 MTR-
11 MTRE
12 (NC)
13 +48 V
14 +48 VG
TB4101(ANT)
1NA V1 TX+
2NA V1 TX-
3NA V1 RX+
4NA V1 RX-
5NA V2 TX+
6NA V2 TX-
7NA V2 RX+
8NA V2 RX-
9LO G RX +
10 LO G RX -
11 ALMTX+
12 ALMTX-
13 ALMRX+
14 ALMRX-
15 ARPAT X+
16 ARPAT X-
17 JAR PA TX+
18 JAR PA TX-
19 NSKT X+
20 NSKT X-
21 HDG RX+
22 HDG RX-
TB4501(OPTION) 1ARPAALM+
2ARPAALM-
3SYSALM+
4SYSALM+
5PWRALM+
6PWRALM-
7ARPAAC K+
8ARPAAC K-
9SYSACK+
10 SYSACK-
11 PWRACK+
12 PWRACK-
13 EXEVT+
14 EXEVT-
15 AISTX+
16 AISTX-
17 AIS_TG
18 AISRX+
19 AISRX-
20 AIS_RG
21 MNTTX+
22 MNTTX-
TB4601(ALARM) TB4401(EXT RADAR)
1RBVD
2RBVDE
3ETIY3
4ETIY3E
5SVD1
6SVD1E
7ETIY1
8ETIY1E
9EXφA1
10 EXφA1E
11 EXφB1
12 EXφB1E
13 EXφZ1
14 EXφZ1E
15
16
17
18
19
20
21
22
23
24
25 (NC)
26 (NC)
27 ACKOUT+
28 ACKOUT-
29 WMRST+
30 WMRST-
SVD2
SVD2E
ETIY2
ETIY2E
EXφA2
EXφA2E
EXφB2
EXφB2E
EXφZ2
EXφZ2E
1(NC)
2
3
4
5P1+
6P1-
7
8
9S1+
10 S2-
11
12
TB4801(LOG)
(NC)
(NC)
(NC)
(NC)
(NC)
(NC)
(NC) U
W
V
FILTER ACIN
1 U
2 V
3FG
CBD-1684A TB521
1 +
2ー
3FG
CBD-1684A TB522
CDC-1324
J4409(DSUB-15P)
R
CQD-1891
(JRC SUPPLY)
G
B
H
V
RED
GRN
BLU
GR Y
BLK
11/R1
22/S1
33/S2
4S3
55/R2
6(NC)
TB4701(GYRO)
2A
1A
J4
J5
J2
2A
1A
VD
VDE
COM+
COM-
2A
1A
J3
J1
TRIG+
TRIG-
BP+
BP-
BZ+
BZ-
PTI
PTE
TXI
TXE
LVR
PMS
E
P82
P81
PTI
PTE
TXI
TXE
LVR
PMS
E
P2
P1
SCANNER UNIT
NKE-2254-6HS
PERFORMANCE
MONITOR
NJU-85
DISPLAY UNIT NCD-4990
BLU
1
YE L
GRN
WHT-B LU
WHT-WH T
ORG
BLK
PNK
BR N
2
RED
PUR
WHT-YEL
WHT-WH T
H-2695111153
(JRC SUPPLY)
1VDIN1
2VDIN1E
3TRIGIN1
4TRIGIN1E
5BPIN1
6BPIN1E
7BZIN1
8BZIN1E
9MTRIN1+
10 MTRIN1-
11 MTRIN1E
12 PWRIN1
13 PWRIN1E
14 PWROUT1
15 PWROUT1E
16 VDOUT1
17 VDOUT1E
18 TRIGOUT1
19 TRIGOUT1E
20 BPOUT1
21 BPOUT1E
22 BZOUT1
23 BZOUT1E
24 MTROUT1+
25 MTROUT1-
26 MTROUT1E
TB4201(ISW IN/OUT)
RADAR
(INTERSWITC H)
WHT
RED
WH T
BLK
ECDIS
H-2695110006
(JRC SUPPLY)
250V-TTYCS-1
250V-TTYCS-1
CONNING
DISPLAY
VDR
3C-2V x5 (MAX 30m)
250V-TTYCS-1
250V-TTYCS-1
250V-TTYCS-1
250V-TTYCS-1
DGPS
ECHO
SOUNDER
LOG
(NMEA0183)
250V-TTYCS-4
AIS
0.6/1kV-DPYCYS-1.5
250V-MPYCYS-7
GYRO
LOG
(200P /NM)
0.6/1kV-DPYCYS-1.5
ALARM MONITORING
SYSTEM
(NEAREST APPROACH)
YEL.T/PNK.T
BLK.T/SKY.T
ORN
BLK
GRN
YEL
WHT
WHT.T/ O RN.T
RED.T/GRN.T
PUR.T/BRN.T
BLU.T/GRY.T
SHIP’S MAINS
AC100-115V/AC220-240V 50/60Hz 1φ
W406 H-7ZCRD1342 A
(Wiring is com pleted .)
(X-BAND 25kW RADAR)
JMA-9122-6XAH レーダー 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9122-6XAH
WHT
BLK
WHT
BRN
BLU
RED
BLK
WHT
BRN
BLU
RED
BLK
BLK . T/SKY .T
YE L .T/ PNK.T
ORN
GR N
BLK
WH T
YEL
PUR. T/ BRN.T
R ED .T/ GR N. T
WHT.T/ORN.T
BLU .T /G RY .T
19-CORES COMPOSITE CABLE (JRC SUPPLY)
CFQ-6912-**
CQD-2097 T ERMINAL BOARD
1
2
3
U
V
UT H
TB105
CIRCUIT BREAKER
5A
(SHIP YARD SUPPLY)
0.6/1kV-DPYCYS-1.5
AC100V,1φ,100W
NBL-175
STEP-DOWN
TRANSFORMER
0.6/1kV-DPYCYS-1.5
0.6/1kV-DPYCYS-1.5
SHIP’S MAINS
AC220V, 1φ,for HEATER
“D” HEATER OPTION
Wiring of PERFOR MAN CE MONITOR
is completed.
0.6/1kV-DPYCY-6
J4407
RJ-45 LAN
U
V
W
CBD-1661 ACOUT1
BATT IN -
BATT IN +
SH IE L D
COAXIAL
CO A XI AL
SHIELD
B－36
JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection Diagram
B.7.4 JMA-9122-6XAH (desktop)
Fig B-32: Terminal Board Connection Diagram of JMA-9122-6XAH (desktop)
1VD+
2VD-
3TRIG+
4TRIG-
5BP+
6BP-
7BZ+
8BZ-
9MTR+
10 MTR-
11 MTRE
12 (NC)
13 +48 V
14 +48 VG
TB4101(ANT)
1NA V1 TX+
2NA V1 TX-
3NA V1 RX+
4NA V1 RX-
5NA V2 TX+
6NA V2 TX-
7NA V2 RX+
8NA V2 RX-
9LO G RX +
10 LO G RX -
11 ALMTX+
12 ALMTX-
13 ALMRX+
14 ALMRX-
15 ARPAT X+
16 ARPAT X-
17 JAR PA TX+
18 JAR PA TX-
19 NSKT X+
20 NSKT X-
21 HDG RX+
22 HDG RX-
TB4501(OPTION) 1ARPAALM+
2ARPAALM-
3SYSALM+
4SYSALM+
5PWRALM+
6PWRALM-
7ARPAAC K+
8ARPAAC K-
9SYSACK+
10 SYSACK-
11 PWRACK+
12 PWRACK-
13 EXEVT+
14 EXEVT-
15 AISTX+
16 AISTX-
17 AIS_TG
18 AISRX+
19 AISRX-
20 AIS_RG
21 MNTTX+
22 MNTTX-
TB4601(ALARM) TB4401(EXT RADAR)
1RBVD
2RBVDE
3ETIY3
4ETIY3E
5SVD1
6SVD1E
7ETIY1
8ETIY1E
9EXφA1
10 EXφA1E
11 EXφB1
12 EXφB1E
13 EXφZ1
14 EXφZ1E
15
16
17
18
19
20
21
22
23
24
25 (NC)
26 (NC)
27 ACKOUT+
28 ACKOUT-
29 WMRST+
30 WMRST-
SVD2
SVD2E
ETIY2
ETIY2E
EXφA2
EXφA2E
EXφB2
EXφB2E
EXφZ2
EXφZ2E
1(NC)
2
3
4
5P1+
6P1-
7
8
9S1+
10 S2-
11
12
TB4801(LOG)
(NC)
(NC)
(NC)
(NC)
(NC)
(NC)
(NC)
1 +
2ー
3FG
TB401
CDC-1324
J4409(DSUB-15P)
R
CQD-1891
(JRC SUPPLY)
G
B
H
V
RED
GRN
BLU
GR Y
BLK
11/R1
22/S1
33/S2
4S3
55/R2
6(NC)
TB4701(GYRO)
2A
1A
J4
J5
J2
2A
1A
VD
VDE
COM+
COM-
2A
1A
J3
J1
TRIG+
TRIG-
BP+
BP-
BZ+
BZ-
PTI
PTE
TXI
TXE
LVR
PMS
E
P82
P81
PTI
PTE
TXI
TXE
LVR
PMS
E
P2
P1
SCANNER UNIT
NKE-2254-6HS
PERFORMANCE
MONITOR
NJU-85
DISPLAY UNIT NCD-4990T
BLU
1
YE L
GRN
WHT-B LU
WHT-WH T
ORG
BLK
PNK
BR N
2
RED
PUR
WHT-YEL
WHT-WH T
H-2695111153
(JRC SUPPLY)
1VDIN1
2VDIN1E
3TRIGIN1
4TRIGIN1E
5BPIN1
6BPIN1E
7BZIN1
8BZIN1E
9MTRIN1+
10 MTRIN1-
11 MTRIN1E
12 PWRIN1
13 PWRIN1E
14 PWROUT1
15 PWROUT1E
16 VDOUT1
17 VDOUT1E
18 TRIGOUT1
19 TRIGOUT1E
20 BPOUT1
21 BPOUT1E
22 BZOUT1
23 BZOUT1E
24 MTROUT1+
25 MTROUT1-
26 MTROUT1E
TB4201(ISW IN/OUT)
RADAR
(INTERSWITC H)
WHT
RED
WH T
BLK
ECDIS
H-2695110006
(JRC SUPPLY)
250V-TTYCS-1
250V-TTYCS-1
CONNING
DISPLAY
VDR
3C-2V x5 (MAX 30m)
250V-TTYCS-1
250V-TTYCS-1
250V-TTYCS-1
250V-TTYCS-1
DGPS
ECHO
SOUNDER
LOG
(NMEA0183)
250V-TTYCS-4
AIS
0.6/1kV-DPYCYS-1.5
250V-MPYCYS-7
GYRO
LOG
(200P /NM)
0.6/1kV-DPYCYS-1.5
ALARM MONITORING
SYSTEM
(NEAREST APPROACH)
YEL.T/PNK.T
BLK.T/SKY.T
ORN
BLK
GRN
YEL
WHT
WHT.T/ O RN.T
RED.T/GRN.T
PUR.T/BRN.T
BLU.T/GRY.T
SHIP’S MAINS
AC100-115V/AC220-240V 50/60Hz 1φ
(X-BAND 25kW RADAR)
JMA-9122-6XAH レーダー（卓上型） 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9122-6XAH(desktop)
WHT
BLK
WHT
BRN
BLU
RED
BLK
WHT
BRN
BLU
RED
BLK
BLK . T/SKY .T
YE L .T/ PNK.T
ORN
GR N
BLK
WH T
YEL
PUR. T/ BRN.T
R ED .T/ GR N. T
WHT.T/ORN.T
BLU .T /G RY .T
19-CORES COMPOSITE CABLE (JRC SUPPLY)
CFQ-6912-**
CQD-2097 T ERMINAL BOARD
1
2
3
U
V
UT H
TB105
CIRCUIT BREAKER
5A
(SHIP YARD SUPPLY)
0.6/1kV-DPYCYS-1.5
AC100V,1φ,100W
NBL-175
STEP-DOWN
TRANSFORMER
0.6/1kV-DPY CYS-1.5
0.6/1kV-DPYCYS-1.5
SHIP’S MAINS
AC220V, 1φ,for HEATER
“D” HEATER OPTION
Wiring of PERFOR MAN CE MONITOR
is completed.
U
W
V
FILTER ACIN
1 U
2 V
3 W
TB402
W405 H-7ZC RD1341A(JRC SUPPLY)
Wiring is completed.
WHT
BLK
RED
RED
WHT
BLK
W407 H-7ZCRD1343 A
(JRC SUPPLY)
1 U
2 V
3FG
CBD-1684A TB 521
W 408 H-7ZC RD 134 4A
( JRC SUPPL Y)
WHT
BLK
GRN
BLK- BL K
WH T- B LK
1 +
2ー
3FG
CBD-1684A TB 522
AC/DC CONVERTER UNIT
NBA-5135
GRN
BLK
WHT
GRN
BLK-BLK
WHT-BLK
GR N
0.6/1kV-DPYCY-6
J4407
RJ-45 LAN
U
V
W
CBD-1661 ACOUT1
BATT IN -
BATT IN +
SH IE L D
COAXIAL
COAXIAL
SHIELD
JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection Diagram
B－37
B
B.7.5 JMA-9122-6XA/9XA
Fig B-33: Terminal Board Connection Diagram of JMA-9122-6XA/9XA
1VD+
2VD-
3TRIG+
4TRIG-
5BP+
6BP-
7BZ+
8BZ-
9MTR+
10 MTR-
11 MTRE
12 (NC)
13 +48 V
14 +48 VG
TB4101(ANT)
1NA V1 TX+
2NA V1 TX-
3NA V1 RX+
4NA V1 RX-
5NA V2 TX+
6NA V2 TX-
7NA V2 RX+
8NA V2 RX-
9LO G RX +
10 LO G RX -
11 ALMTX+
12 ALMTX-
13 ALMRX+
14 ALMRX-
15 ARPAT X+
16 ARPAT X-
17 JAR PA TX+
18 JAR PA TX-
19 NSKT X+
20 NSKT X-
21 HDG RX+
22 HDG RX-
TB4501(OPTION) 1ARPAALM+
2ARPAALM-
3SYSALM+
4SYSALM+
5PWRALM+
6PWRALM-
7ARPAAC K+
8ARPAAC K-
9SYSACK+
10 SYSACK-
11 PWRACK+
12 PWRACK-
13 EXEVT+
14 EXEVT-
15 AISTX+
16 AISTX-
17 AIS_TG
18 AISRX+
19 AISRX-
20 AIS_RG
21 MNTTX+
22 MNTTX-
TB4601(ALARM) TB4401(EXT RADAR)
1RBVD
2RBVDE
3ETIY3
4ETIY3E
5SVD1
6SVD1E
7ETIY1
8ETIY1E
9EXφA1
10 EXφA1E
11 EXφB1
12 EXφB1E
13 EXφZ1
14 EXφZ1E
15
16
17
18
19
20
21
22
23
24
25 (NC)
26 (NC)
27 ACKOUT+
28 ACKOUT-
29 WMRST+
30 WMRST-
SVD2
SVD2E
ETIY2
ETIY2E
EXφA2
EXφA2E
EXφB2
EXφB2E
EXφZ2
EXφZ2E
1(NC)
2
3
4
5P1+
6P1-
7
8
9S1+
10 S2-
11
12
TB4801(LOG)
(NC)
(NC)
(NC)
(NC)
(NC)
(NC)
(NC) U
W
V
FILTER ACIN
CDC-1324
J4409(DSUB-15P)
R
CQD-1891
(JRC SUPPLY)
G
B
H
V
RED
GRN
BLU
GR Y
BLK
11/R1
22/S1
33/S2
4S3
55/R2
6(NC)
TB4701(GYRO)
PTI
PTE
TXI
TXE
LVR
PMS
E
P82
P81
PTI
PTE
TXI
TXE
LVR
PMS
E
P2
P1
SCANNER UNIT
NKE-1125-61/62/91/92
PERFORMANCE
MONITOR
NJU-85
DISPLAY UNIT NCD-4990
BLU
1
YE L
GRN
WHT-B LU
WHT-WH T
ORG
BLK
PNK
BR N
2
RED
PUR
WHT-YEL
WHT-WH T
H-2695111153
(JRC SUPPLY)
1VDIN1
2VDIN1E
3TRIGIN1
4TRIGIN1E
5BPIN1
6BPIN1E
7BZIN1
8BZIN1E
9MTRIN1+
10 MTRIN1-
11 MTRIN1E
12 PWRIN1
13 PWRIN1E
14 PWROUT1
15 PWROUT1E
16 VDOUT1
17 VDOUT1E
18 TRIGOUT1
19 TRIGOUT1E
20 BPOUT1
21 BPOUT1E
22 BZOUT1
23 BZOUT1E
24 MTROUT1+
25 MTROUT1-
26 MTROUT1E
TB4201(ISW IN/OUT)
RADAR
(INTERSWITC H)
WHT
RED
WH T
BLK
ECDIS
H-2695110006
(JRC SUPPLY)
250V-TTYCS-1
250V-TTYCS-1
CONNING
DISPLAY
VDR
3C-2V x5 (MAX 30m)
250V-TTYCS-1
250V-TTYCS-1
250V-TTYCS-1
250V-TTYCS-1
DGPS
ECHO
SOUNDER
LOG
(NMEA0183)
250V-TTYCS-4
AIS
0.6/1kV-DPYCYS-1.5
250V-MPYCYS-7
GYRO
LOG
(200P /NM)
0.6/1kV-DPYCYS-1.5
ALARM MONITORING
SYSTEM
(NEAREST APPROACH)
RED
BLU
3
ORN
WHT
SHIP’S MAINS
AC100-115V/AC220-240V 50/60Hz 1φ
(X-BAND 25kW RADAR)
JMA-9122-6XA/9XA レーダー 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9122-6XA/9XA
WHT
BLK
WHT
BRN
BLU
RED
BLK
WHT
BRN
BLU
RED
BLK
19-C ORES COMPOSITE CABLE (JRC SUPPLY)
H-2695110056
CQD-2097 T ERMINAL BOARD
1
2
4
YEL
GRN
1
VD+
2
VD-
3
TRIG+
4
TRIG-
5
BP+
6
BP-
7
BZ+
8
BZ-
9
MTR+
10
MTR-
11
MTRE
TB101 1
2
3
V1
4
W1
5
+48V
6
+48VG
U1
TB102
ORN
WHT
1
2
4
3
GRN
YEL
BLU
RE D
1
2
3
U
V
UT H
TB105
CIRCUIT BREAKER
5A
(SHIP YARD SUPPLY)
0.6/1kV-DPYCYS-1.5
AC100V,1φ,100W
NBL-175
STEP-DOWN
TRANSFORMER
0.6/1kV-DPYC YS-1.5
0.6/1kV-DPYCYS-1.5
SHIP’S MAINS
AC220V, 1φ,for HEATER
“D” HEATER OPTION
Wiring of PERFOR MAN CE MONITOR
is completed.
0.6/1kV-DPYCY-6
J4407
RJ-45 LAN
U
V
W
CBD-1661 ACOUT1
BATT IN -
BATT IN +
B－38
JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection Diagram
B.7.6 JMA-9123-7XA/9XA
Fig B-34: Terminal Board Connection Diagram of JMA-9123-7XA/9XA
1VD+
2VD-
3TRIG+
4TRIG-
5BP+
6BP-
7BZ+
8BZ-
9MTR+
10 MTR-
11 MTRE
12 (NC)
13 +48 V
14 +48 VG
TB4101(ANT)
1NA V1 TX+
2NA V1 TX-
3NA V1 RX+
4NA V1 RX-
5NA V2 TX+
6NA V2 TX-
7NA V2 RX+
8NA V2 RX-
9LO G RX +
10 LO G RX -
11 ALMTX+
12 ALMTX-
13 ALMRX+
14 ALMRX-
15 ARPAT X+
16 ARPAT X-
17 JAR PA TX+
18 JAR PA TX-
19 NSKT X+
20 NSKT X-
21 HDG RX+
22 HDG RX-
TB4501(OPTION) 1ARPAALM+
2ARPAALM-
3SYSALM+
4SYSALM+
5PWRALM+
6PWRALM-
7ARPAAC K+
8ARPAAC K-
9SYSACK+
10 SYSACK-
11 PWRACK+
12 PWRACK-
13 EXEVT+
14 EXEVT-
15 AISTX+
16 AISTX-
17 AIS_TG
18 AISRX+
19 AISRX-
20 AIS_RG
21 MNTTX+
22 MNTTX-
TB4601(ALARM) TB4401(EXT RADAR)
1RBVD
2RBVDE
3ETIY3
4ETIY3E
5SVD1
6SVD1E
7ETIY1
8ETIY1E
9EXφA1
10 EXφA1E
11 EXφB1
12 EXφB1E
13 EXφZ1
14 EXφZ1E
15
16
17
18
19
20
21
22
23
24
25 (NC)
26 (NC)
27 ACKOUT+
28 ACKOUT-
29 WMRST+
30 WMRST-
SVD2
SVD2E
ETIY2
ETIY2E
EXφA2
EXφA2E
EXφB2
EXφB2E
EXφZ2
EXφZ2E
1(NC)
2
3
4
5P1+
6P1-
7
8
9S1+
10 S2-
11
12
TB4801(LOG)
(NC)
(NC)
(NC)
(NC)
(NC)
(NC)
(NC) U
W
V
FILTER ACIN
CDC-1324
J4409(DSUB-15P)
R
CQD-1891
(JRC SUPPLY)
G
B
H
V
RED
GRN
BLU
GR Y
BLK
11/R1
22/S1
33/S2
4S3
55/R2
6(NC)
TB4701(GYRO)
PTI
PTE
TXI
TXE
LVR
PMS
E
P82
P81
PTI
PTE
TXI
TXE
LVR
PMS
E
P2
P1
SCANNER UNIT
NKE-1129-71/72/91/92
PERFORMANCE
MONITOR
NJU-85
DISPLAY UNIT NCD-4990
BLU
1
YE L
GRN
WHT-B LU
WHT-WH T
ORG
BLK
PNK
BR N
2
RED
PUR
WHT-YEL
WHT-WH T
H-2695111153
(JRC SUPPLY)
1VDIN1
2VDIN1E
3TRIGIN1
4TRIGIN1E
5BPIN1
6BPIN1E
7BZIN1
8BZIN1E
9MTRIN1+
10 MTRIN1-
11 MTRIN1E
12 PWRIN1
13 PWRIN1E
14 PWROUT1
15 PWROUT1E
16 VDOUT1
17 VDOUT1E
18 TRIGOUT1
19 TRIGOUT1E
20 BPOUT1
21 BPOUT1E
22 BZOUT1
23 BZOUT1E
24 MTROUT1+
25 MTROUT1-
26 MTROUT1E
TB4201(ISW IN/OUT)
RADAR
(INTERSWITC H)
WHT
RED
WH T
BLK
ECDIS
H-2695110006
(JRC SUPPLY)
250V-TTYCS-1
250V-TTYCS-1
CONNING
DISPLAY
VDR
3C-2V x5 (MAX 30m)
250V-TTYCS-1
250V-TTYCS-1
250V-TTYCS-1
250V-TTYCS-1
DGPS
ECHO
SOUNDER
LOG
(NMEA0183)
250V-TTYCS-4
AIS
0.6/1kV-DPYCYS-1.5
250V-MPYCYS-7
GYRO
LOG
(200P /NM)
0.6/1kV-DPYCYS-1.5
ALARM MONITORING
SYSTEM
(NEAREST APPROACH)
RED
BLU
3
ORN
WHT
SHIP’S MAINS
AC100-115V/AC220-240V 50/60Hz 1φ
(X-BAND 25kW RADAR)
JMA-9123-7XA/9XA レーダー 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9123-7XA/9XA
WHT
BLK
WHT
BRN
BLU
RED
BLK
WHT
BRN
BLU
RED
BLK
19-C ORES COMPOSITE CABLE (JRC SUPPLY)
H-2695110056
CQD-2097 T ERMINAL BOARD
1
2
4
YEL
GRN
1
2
3
U
V
UT H
TB105
CIRCUIT BREAKER
5A
( SHIP YA RD SU PPLY )
0.6/1kV-DPYCYS-1.5
AC100V,1φ,100W
NBL -175
STEP -DO WN
TRA NSFO RME R
0.6/1kV-DPYCYS-1.5
0.6/1kV -DPYCYS-1.5
SHIP’S MAINS
AC 220V , 1φ,for HEATER
“D” HEATER OPTION
PTI
PTE
LVR
PMS
(NC)
E
TB104
TXI
TXE
1
2
3
4
5
6
7
8
E
9
10 VER R
1
ΦB
2
3
C2
4
ΦZE
5
U1
6
V1
7
W1
8
+12v
9
ΦZ
10
ΦA
E
TB103
1
2
3V1
4
5U0
6V0
U1
TB202
1
GR N
YEL
FR-9 FLEXIBLE WAVEGUIDE
(JRC SUPPLY)
19-CORES COMPOSITE CABLE (JRC SUPPLY)
H-2695110056
1
MTRE
2
3
BP+
4
BP-/BZ-
5
VD+
6
VD-
7
TRIG+
8
TRIG-
9
BZ+
10
MTR+
MTR-
TB201 1
2
3
ΦA
4
E
5
+12V
6
C2
7
ΦZE
8
ΦZ
9
ΦB
10 +48V
+48VG
TB203 1
2
3
4
5
6
7
8
9
10
TB204
PTI
PTE
LVR
PMS
(NC)
E
TXI
TXE
E
VERR
2
3
GRN
YE L
RED
BLU
4
ORN
WHT
ORN
WH T
3
1
2
4
GRY
RED
BLU
TRANSCEIVER UNIT NTG-3225
4
GRY
BLU
RED
2
1
3
WHT
OR N
YEL
GR N
Wiring of PERFOR MAN CE MONITOR
is completed.
0.6/1kV-DPY CY-6
PUR
BLK
PUR
BLK
J4407
RJ-45 LAN
U
V
W
CBD-1661 ACOUT1
BATT IN -
BATT IN +
JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection Diagram
B－39
B
B.7.7 JMA-9132-SA
Fig B-35: Terminal Board Connection Diagram of JMA-9132-SA
1VD+
2VD-
3TRIG+
4TRIG-
5BP+
6BP-
7BZ+
8BZ-
9MTR+
10 MTR-
11 MTRE
12 (NC)
13 +48 V
14 +48 VG
TB4101(ANT)
1NA V1 TX+
2NA V1 TX-
3NA V1 RX+
4NA V1 RX-
5NA V2 TX+
6NA V2 TX-
7NA V2 RX+
8NA V2 RX-
9LO G RX +
10 LO G RX -
11 ALMTX+
12 ALMTX-
13 ALMRX+
14 ALMRX-
15 ARPAT X+
16 ARPAT X-
17 JAR PA TX+
18 JAR PA TX-
19 NSKT X+
20 NSKT X-
21 HDG RX+
22 HDG RX-
TB4501(OPTION) 1ARPAALM+
2ARPAALM-
3SYSALM+
4SYSALM+
5PWRALM+
6PWRALM-
7ARPAAC K+
8ARPAAC K-
9SYSACK+
10 SYSACK-
11 PWRACK+
12 PWRACK-
13 EXEVT+
14 EXEVT-
15 AISTX+
16 AISTX-
17 AIS_TG
18 AISRX+
19 AISRX-
20 AIS_RG
21 MNTTX+
22 MNTTX-
TB4601(ALARM) TB4401(EXT RADAR)
1RBVD
2RBVDE
3ETIY3
4ETIY3E
5SVD1
6SVD1E
7ETIY1
8ETIY1E
9EXφA1
10 EXφA1E
11 EXφB1
12 EXφB1E
13 EXφZ1
14 EXφZ1E
15
16
17
18
19
20
21
22
23
24
25 (NC)
26 (NC)
27 ACKOUT+
28 ACKOUT-
29 WMRST+
30 WMRST-
SVD2
SVD2E
ETIY2
ETIY2E
EXφA2
EXφA2E
EXφB2
EXφB2E
EXφZ2
EXφZ2E
1(NC)
2
3
4
5P1+
6P1-
7
8
9S1+
10 S2-
11
12
TB4801(LOG)
(NC)
(NC)
(NC)
(NC)
(NC)
(NC)
(NC) U
W
V
FILTER ACIN
CDC-1324
J4409(DSUB-15P)
R
CQD-1891
(JRC SUPPLY)
G
B
H
V
RED
GRN
BLU
GR Y
BLK
11/R1
22/S1
33/S2
4S3
55/R2
6(NC)
TB4701(GYRO)
PTI
PTE
TXI
TXE
LVR
PMS
E
P82
P81
PTI
PTE
TXI
TXE
LVR
PMS
E
P2
P1
SCANNER UNIT
NKE-1130-1/2
PERFORMANCE
MONITOR
NJU-84
DISPLAY UNIT NCD-4990
BLU
1
YE L
GRN
WHT-B LU
WHT-WH T
ORG
BLK
PNK
BR N
2
RED
PUR
WHT-YEL
WHT-WH T
H-2695111153
(JRC SUPPLY)
1VDIN1
2VDIN1E
3TRIGIN1
4TRIGIN1E
5BPIN1
6BPIN1E
7BZIN1
8BZIN1E
9MTRIN1+
10 MTRIN1-
11 MTRIN1E
12 PWRIN1
13 PWRIN1E
14 PWROUT1
15 PWROUT1E
16 VDOUT1
17 VDOUT1E
18 TRIGOUT1
19 TRIGOUT1E
20 BPOUT1
21 BPOUT1E
22 BZOUT1
23 BZOUT1E
24 MTROUT1+
25 MTROUT1-
26 MTROUT1E
TB4201(ISW IN/OUT)
RADAR
(INTERSWITC H)
WHT
RED
WH T
BLK
ECDIS
H-2695110006
(JRC SUPPLY)
250V-TTYCS-1
250V-TTYCS-1
CONNING
DISPLAY
VDR
3C-2V x5 (MAX 30m)
250V-TTYCS-1
250V-TTYCS-1
250V-TTYCS-1
250V-TTYCS-1
DGPS
ECHO
SOUNDER
LOG
(NMEA0183)
250V-TTYCS-4
AIS
0.6/1kV-DPYCYS-1.5
250V-MPYCYS-7
GYRO
LOG
(200P /NM)
0.6/1kV-DPYCYS-1.5
ALARM MONITORING
SYSTEM
(NEAREST APPROACH)
RED
BLU
3
ORN
WHT
0.6/1kV-DPYCY-6
SHIP’S MAINS
AC100-115V/AC220-240V 50/60Hz 1φ
(S-BAND 30kW RADAR)
JMA-9132-SA レーダー 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9132-SA
WHT
BLK
WHT
BRN
BLU
RED
BLK
WHT
BRN
BLU
RED
BLK
19-C ORES COMPOSITE CABLE (JRC SUPPLY)
H-2695110056
CQD-2097 T ERMINAL BOARD
1
2
4
YEL
GRN
1
VD+
2
VD-
3
TRIG+
4
TRIG-
5
BP+
6
BP-
7
BZ+
8
BZ-
9
MTR+
10
MTR-
11
MTRE
TB101 1
2
3V14W15
+48V
6
+48VG
U1
TB102
ORN
WHT
1
2
4
3
GRN
YEL
BLU
RE D
UT H
CIRCUIT BREAKER
5A
(SHIP YARD SUPPLY)
0.6/1kV -DPYCYS-1.5
AC100V,1φ,100W
NBL-175
STEP-DOWN
TRANSFORMER
0.6/1kV-DPYCYS-1.5
0.6/1kV-DPYCYS-1.5
SHIP’S MAINS
AC220V, 1φ,for HEATER
“D” HEATER OPTION
7
8
9
10
Wiring of PERFOR MAN CE MONITOR
is completed.
U
V
11
12
J4407
RJ-45 LAN
U
V
W
CBD-1661 ACOUT1
BATT IN -
BATT IN +
B－40
JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection Diagram
B.7.8 JMA-9133-SA
Fig B-36: Terminal Board Connection Diagram of JMA-9133-SA
1VD+
2VD-
3TRIG+
4TRIG-
5BP+
6BP-
7BZ+
8BZ-
9MTR+
10 MTR-
11 MTRE
12 (NC)
13 +48 V
14 +48 VG
TB4101(ANT)
1NA V1 TX+
2NA V1 TX-
3NA V1 RX+
4NA V1 RX-
5NA V2 TX+
6NA V2 TX-
7NA V2 RX+
8NA V2 RX-
9LO G RX +
10 LO G RX -
11 ALMTX+
12 ALMTX-
13 ALMRX+
14 ALMRX-
15 ARPAT X+
16 ARPAT X-
17 JAR PA TX+
18 JAR PA TX-
19 NSKT X+
20 NSKT X-
21 HDG RX+
22 HDG RX-
TB4501(OPTION) 1ARPAALM+
2ARPAALM-
3SYSALM+
4SYSALM+
5PWRALM+
6PWRALM-
7ARPAAC K+
8ARPAAC K-
9SYSACK+
10 SYSACK-
11 PWRACK+
12 PWRACK-
13 EXEVT+
14 EXEVT-
15 AISTX+
16 AISTX-
17 AIS_TG
18 AISRX+
19 AISRX-
20 AIS_RG
21 MNTTX+
22 MNTTX-
TB4601(ALARM) TB4401(EXT RADAR)
1RBVD
2RBVDE
3ETIY3
4ETIY3E
5SVD1
6SVD1E
7ETIY1
8ETIY1E
9EXφA1
10 EXφA1E
11 EXφB1
12 EXφB1E
13 EXφZ1
14 EXφZ1E
15
16
17
18
19
20
21
22
23
24
25 (NC)
26 (NC)
27 ACKOUT+
28 ACKOUT-
29 WMRST+
30 WMRST-
SVD2
SVD2E
ETIY2
ETIY2E
EXφA2
EXφA2E
EXφB2
EXφB2E
EXφZ2
EXφZ2E
1(NC)
2
3
4
5P1+
6P1-
7
8
9S1+
10 S2-
11
12
TB4801(LOG)
(NC)
(NC)
(NC)
(NC)
(NC)
(NC)
(NC) U
W
V
FILTER ACIN
CDC-1324
J4409(DSUB-15P)
R
CQD-1891
(JRC SUPPLY)
G
B
H
V
RED
GRN
BLU
GR Y
BLK
11/R1
22/S1
33/S2
4S3
55/R2
6(NC)
TB4701(GYRO)
PTI
PTE
TXI
TXE
LVR
PMS
E
P82
P81
PTI
PTE
TXI
TXE
LVR
PMS
E
P2
P1
SCANNER UNIT
NKE-1139-1/2
PERFORMANCE
MONITOR
NJU-84
DISPLAY UNIT NCD-4990
BLU
1
YE L
GRN
WHT-B LU
WHT-WH T
ORG
BLK
PNK
BR N
2
RED
PUR
WHT-YEL
WHT-WH T
H-2695111153
(JRC SUPPLY)
1VDIN1
2VDIN1E
3TRIGIN1
4TRIGIN1E
5BPIN1
6BPIN1E
7BZIN1
8BZIN1E
9MTRIN1+
10 MTRIN1-
11 MTRIN1E
12 PWRIN1
13 PWRIN1E
14 PWROUT1
15 PWROUT1E
16 VDOUT1
17 VDOUT1E
18 TRIGOUT1
19 TRIGOUT1E
20 BPOUT1
21 BPOUT1E
22 BZOUT1
23 BZOUT1E
24 MTROUT1+
25 MTROUT1-
26 MTROUT1E
TB4201(ISW IN/OUT)
RADAR
(INTERSWITC H)
WHT
RED
WH T
BLK
ECDIS
H-2695110006
(JRC SUPPLY)
250V-TTYCS-1
250V-TTYCS-1
CONNING
DISPLAY
VDR
3C-2V x5 (MAX 30m)
250V-TTYCS-1
250V-TTYCS-1
250V-TTYCS-1
250V-TTYCS-1
DGPS
ECHO
SOUNDER
LOG
(NMEA0183)
250V-TTYCS-4
AIS
0.6/1kV-DPYCYS-1.5
250V-MPYCYS-7
GYRO
LOG
(200P /NM)
0.6/1kV-DPYCYS-1.5
ALARM MONITORING
SYSTEM
(NEAREST APPROACH)
RED
BLU
3
ORN
WHT
0.6/1kV-DPYCY-6
SHIP’S MAINS
AC100-115V/AC220-240V 50/60Hz 1φ
(S-BAND 30kW RADAR)
JMA-9133-SA レーダー 盤間接続図
INTERCONNECTION DIAGRAM OF RADAR TYPE JMA-9133-SA
WHT
BLK
WHT
BRN
BLU
RED
BLK
WHT
BRN
BLU
RED
BLK
14-C ORES COMPOSITE CABLE (JRC SUPPLY)
H-2695110056
CQD-2097 T ERMINAL BOARD
1
2
4
YEL
GRN
CIRCUIT BREAKER
5A
( SHIP YA RD SU PPLY )
0.6/1kV-DPYCYS-1.5
AC100V,1φ,100W
NBL -175
STEP -DO WN
TRA NSFO RME R
0.6/1kV-DPYCYS-1.5
0.6/1kV-DPYCYS-1.5
SHIP’S MAINS
AC 220V , 1φ,for HEATER
“D” HEATER OPTION
PTI
PTE
LVR
PMS
(NC)
E
TB104
TXI
TXE
1
2
3
4
5
6
7
8
9
10
1
ΦB
2
3
C2
4
ΦZE
5
U1
6
V1
7
UTH
8
+12v
9ΦZ
10 ΦA
E
TB103
1
2
3
V0
4
W0
5
U1
6
V1
W1
U0
TB202
1
GRN
YE L
HF-20D COAXIAL CABLE
(JRC SUPPLY)
19-CORES COMPOSITE CABLE (JRC SUPPLY)
H-2695110056
1
MTRE
2
3
BP+
4
BP-/BZ-
5
VD+
6
VD-
7
TRIG+
8
TRIG-
9
BZ+
10
MTR+
MTR-
TB201 1
2
3
ΦA
4
E
5
+12V
6
C2
7
ΦZE
8
ΦZ
9
ΦB
10 +48V
+48VG
TB203 1
2
3
4
5
6
7
8
9
10
TB204
PTI
PTE
LVR
PMS
(NC)
E
TXI
TXE
E
VERR
2
3
GRN
YE L
RED
BLU
4
ORN
WHT
ORN
WH T
3
1
2
4
GRY
BLU
RED
TRANSCEIVER UNIT NTG-3230
4
GRY
BLU
RED
2
1
3
WHT
ORN
YE L
GR N
Wiring of PERFOR MAN CE MONITOR
is completed.
E
11
12 VER R
(NC)
(NC)
U
V
11
12
PUR
BLK
PUR
BLK
J4407
RJ-45 LAN
U
V
W
CBD-1661 ACOUT1
BATT IN -
BATT IN +
JMA-9100 Instruction Manual > B.DRAWINGS > B.7 Terminal Board Connection Diagram
B－41
B
B.7.9 NCD-4990T
Fig B-37: Inter-Unit Connection Diagram of NCD-4990T
DISPLAY UNIT NCD-4990T
MONITOR UNIT
NWZ-170
OPERATION UNIT
NCE-5163
SUB OPERATION UNIT
NCE-5163
1 U
2 V
3FG
CBD-1684A TB521
1 +
2ー
3FG
CBD-1684A TB522
RADAR PROCESS UNIT
NDC-1399-9
AC/DC
CONVERTER UNIT
NBA-5135
Option for X-band 10kW and X-band 25kW-HS.
Used with NKE-2103-6,NKE-2103-6HS and NKE-
2254-6HS
1 +
2ー
3FG
TB402
1 U
2 V
3 W
CBD-1661
AC OUT 1
J4311
J4312
CBD-1661
AC OUT 2
Option
Main
Sub
J4406 DVI-D J4309
DSUB -9P
FEMALE
RADAR PROCESS
CIRCUIT
CDC-1324
TERMINAL BOARD
CQD-2097
POWER SUPPLY
CBD-1661
NCD-4990T 卓上型レーダー指示機 ユニット間接続図
INTERCONNECTION DIAGRAM OF DISPLAY UNIT TYPE NCD-4990T(desktop)
JMA-9100 Series RADAR
B－42
JMA-9100 Instruction Manual > B.DRAWINGS > B.8 GYRO I/F
B.8 GYRO I/F
Fig B-38: Parts Location of CMJ-462E
TableB-1： Setting Table of CMJ-462E S1/S2
GYRO INPUT SIGNAL
INDICATOR LED
ジャイロ入力信号LED
GYRO SIGNAL PROCESS
INDICATOR LED
ジャイロ信号処理表示LED
LOG PULSE
INDICATOR LED
ログパルス表示LED
ERROR INDICATOR LED
エラー表示LED
GYRO LOW-VOLTAGE
ALERT LED
ジャイロ低電圧警告LED
SERIAL SIGNAL
INDICATOR LED
シリアル信号表示LED
OPEN
プラグ無し
KEEP DEFAULT
設定不要
LOW-VOLTAGE GYRO
SETTING
ジャイロ低電圧時に設定
S1 SETTING 1 2 3 4 5 6 7 8 S2 SETTING 1 2 3 4 5 6 7 8
STEP ON ON
SYNC OFF BSHLOG ALM OFF
36X ON ON ON
90X OFF ON GYRO SIMULATOR OFF
180X ON OFF ON
RATIO
360X OFF OFF
LOG SIMULATOR OFF
逆／REV ON N.C. (No Connection) OFF
ジャイロ信号
GYRO SETTING
回転方向
DIRECTION 正／NOR OFF
5 SEC ON
シンクロ／SYNC ON
GYRO ALM TIME 0.2 SEC OFF
パルス／PULSE OFF
HDT ( NMEA (HDT/THS) ) ON
未接続／NC OFF
GYRO SRC
(Heading Sensor Source) GYRO OFF
100P／30X ON ON 4800 BPS OFF OFF
200P／90X OFF ON 9600 BPS ON OFF
400P／180X ON OFF 19200 BPS OFF ON
ログ信号
LOG SETTING
パルス
PULSE/NM
800P／360X OFF OFF
NMEA BAUDRATE
38400 BPS ON ON
B－44
JMA-9100 Instruction Manual > B.DRAWINGS > B.9 Inter Switch Unit
B.9 Inter Switch Unit
B.9.1 Terminal Board Connection Diagram
Fig B-39: Terminal Board Connetion Diagram of NQE-3141-2A
VDIN 1
VDIN 1E
TRIGIN 1
TRIGIN 1E
BPIN 1
BPIN 1E
BZIN 1
MTRIN 1+
MTRIN 1-
BZIN 1E
MTRIN 1E
PWRIN 1+
PWRIN 1E
PWROUT 1
PWROUT 1E
VDOUT 1
VDOUT 1E
TRIGOUT 1
TRIGOUT 1E
BPOUT 1
BPOUT 1E
BZOUT 1E
MTROUT 1+
BZOUT 1
MTROUT 1 -
MTORUT 1E
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
VDIN 1
VDIN 1E
TRIGIN 1
TRIGIN 1E
BPIN 1
BPIN 1E
BZIN 1
MTRIN 1+
MTRIN 1-
BZIN 1E
MTRIN 1E
PWRIN 1+
PWRIN 1E
PWROUT 1
PWROUT 1E
VDOUT 1
VDOUT 1E
TRIGOUT 1
TRIGOUT 1E
BPOUT 1
BPOUT 1E
BZOUT 1E
MTROUT 1+
BZOUT 1
MTROUT 1-
MTORUT 1E
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
TB4201
ISW IN/OUT TB4201
ISW IN/OUT
DISPLAY 1 DISPLAY 2
1
2
BLUE
YELLOW
GREEN
WHITE-BLUE
WHITE-WHITE
ORANGE
BLACK
PINK
BROWN
RED
PURPLE
CLEAR
WHITE-YELLOW
WHITE-WHITE
NCD-4990 NCD-4990
H-2695111153
(JRC SUPPLY)
JMA-9100 Instruction Manual > B.DRAWINGS > B.9 Inter Switch Unit
B－45
B
Fig B-40: Terminal Board Connection Diagram of NQE-3141-4A
CH-1
TB911 TB912
DISPLAY1
NCD-4990
TB4201
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
2
3
4
5
6
7
8
9
10
11
DISPLAY2
NCD-4990
TB4201
VDIN 1
VDIN 1E
TRIGIN 1
TRIGIN 1E
BPIN 1
BPIN 1E
BZIN 1
MTRIN 1+
MTRIN 1-
BZIN 1E
MTRIN 1E
PWRIN 1+
PWRIN 1E
PWROUT 1
PWROUT 1E
VDOUT 1
VDOUT 1E
TRIGOUT 1
TRIGOU T 1E
BPOUT 1
BPOUT 1E
BZOUT 1E
MTROUT 1+
BZOUT 1
MTROUT 1-
MTORUT 1E
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
DISPLAY3
NCD-4990
TB4201
CH-2
TB913 TB914
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
2
3
4
5
6
7
8
9
10
11
CH-3
TB915 TB916
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
2
3
4
5
6
7
8
9
10
11
NKE-3141-4
CCL-304R
VDIN 1
VDIN 1E
TRIG IN 1
TRIGIN 1E
BPIN 1
BPIN 1E
BZIN 1
MTRIN 1+
MTRIN 1-
BZIN 1E
MTRIN 1E
PWRIN 1+
PWRIN 1E
PWROUT 1
PWROUT 1E
VDOUT 1
VDOUT 1E
TRIGOUT 1
TRIGOUT 1E
BPOUT 1
BPOUT 1E
BZOUT 1E
MTROUT 1+
BZOUT 1
MTROUT 1-
MTORUT 1E
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
VDIN 1
VDIN 1E
TRIGIN 1
TRIG IN 1E
BPIN 1
BPIN 1E
BZIN 1
MTRIN 1+
MTRIN 1-
BZIN 1E
MTRIN 1E
PWRIN 1+
PWRIN 1E
PWROUT 1
PWROUT 1E
VDOUT 1
VDOUT 1E
TRIGOUT 1
TRIGOUT 1E
BPOUT 1
BPOUT 1E
BZOUT 1E
MTROUT 1+
BZOUT 1
MTROUT 1-
MTORUT 1E
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
1
2
BLU
YEL
GRN
WHT-BLU
WHT-WHT
ORG
BLK
PNK
BRN
RED
PUR
CLR
WHT-YEL
WHT-WHT
1
2
BLU
YEL
GRN
ORG
BLK
PNK
BRN
RED
PUR
1
2
BLU
YEL
GRN
ORG
BLK
PNK
BRN
RED
PUR
2
RED
PUR
WHT
1
BLU
YEL
GR N
ORG
BLK
PNK
BRN
2
RED
PUR
WHT
1
BLU
YEL
GRN
OR
G
BLK
PNK
BRN
2
RED
PUR
CLR
WHT-YEL
WHT-W HT
1
BLU
YEL
GRN
WHT-BLU
WHT-WHT
ORG
BLK
PNK
BRN
H-2695111153 (JRC SUPPLY )
H-2695111153 (JRC SUPPLY )
H-2695111153 (JRC SUPPLY )
VDIN 1
VDIN 1E
TRIGIN 1
TRIGIN 1E
BPIN 1
BPIN 1E
BZIN 1
MTRIN 1+
MTRIN 1-
BZIN 1E
MTRIN 1E
PWRIN 1+
PWRIN 1E
PWROUT 1
PWROUT 1E
VDOUT 1
VDOUT 1E
TRIGOUT 1
TRIGOUT 1E
BPOUT 1
BPOUT 1E
BZOUT 1E
MTROUT 1+
BZOUT 1
MTROUT 1-
MTORUT 1E
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
DISPLAY4
NCD-4990
TB4201
CH-4
TB915 TB916
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
2
3
4
5
6
7
8
9
10
11
1
2
BLU
YEL
GRN
ORG
BLK
PNK
BRN
RED
PUR
2
RED
PUR
WHT
1
BLU
YEL
GR N
OR G
BLK
PNK
BRN
H-2695111153 (JRC SUPPLY )
WHT-YEL
WHT-WHT
WHT-BLU
WHT-WHT WHT-YEL
WHT-WHT
WHT-BLU
WHT-WHT
WHT-YEL
WHT-WHT
WHT-BLU
WHT-WHT
WHT-BLU
WHT-WHT
CLR
WHT-YEL
WHT-WHT
WHT-BLU
WHT-WHT
CLR
WHT-YEL
WHT-WHT
WHT-BLU
WHT-WHT
CLR
WHT-YEL
WHT-WHT
B－46
JMA-9100 Instruction Manual > B.DRAWINGS > B.9 Inter Switch Unit
B.9.2 Interconnection Diagram
Fig B-41: Interconnection Diagram of NQE-3141-2A
Terminal board
J4308 ISW
J903
1
2
3
4
5
6
-15V
GND
GND
GND
5 V
+15V
P903
1
2
3
4
5
6
-15V
GND
GND
GND
5 V
+15V
1
2
1
2
VIN
+
VIN
-
ＴＢ912
ＴＢ914
ＴＢ916
ＴＢ918
ＴＢ911
ＴＢ913
ＴＢ915
ＴＢ917
CH-4CH-3
CH-2CH-1
J3 J3
1
1
26
26
CCL-304
P902J2
J1
CBD-1675H-7ZCRD0971
H-7ZCRD0972
1
26
1
26
CQD-1973 CQD-1973
H-7ZCRD0970A
H-7ZCRD0970A
Terminal board
J4306
(ISW-1CH)
Terminal board
J4307
(ISW-1CH)
JMA-9100 Instruction Manual > B.DRAWINGS > B.9 Inter Switch Unit
B－47
B
Fig B-42: Interconnection Diagram of NQE-3141-4A
11.MTROUT
E
10.MTROUT
-
9.MTROUT+
8.BZOUTE
7.BZOUT
5.BPOUT
6.BPOUTE
2.VDOUTE
3.TRGOUT
4.TRGOUTE
1.VDOUT
15 . PW R OU T
E
14 . PW R OU T
13 . RW R IN E
12 . PW R IN
11 . M T R I NE
9. M T R IN +
10 . M T R I N-
6.B PIN E
7. B Z IN
8. B Z IN E
5.B PIN
4.T R G INE
3.T R G IN
2.V DI NE
1.V DI N
CH-1
TB 911 TB 912 TB 913 TB 914 TB 915 TB 916 TB 917 TB 918
1
2
CCL-304
TO
DISPLAY1
NCD-4990
TB4201
TO
DISPLAY2
NCD-4990
TB4201
TO
DISPLAY3
NCD-4990
TB4201
CH -2 CH-3 CH-4
3
J903
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
10
J904
J905
1
2
J909
-15V
GND
GND
GND
5 V
+15V
AC
(L)
AC
(N)
TRT
P+
E
PO WL ED
TRT
P-
FANV
FANE
FANP LS
1
2
3
4
5
6
-15V
GND
GND
GND
5 V
+15V
P903P902
1
3
5
AC(L )
AC(N)
FG
S
P904
P905
P909
CN2
CN1P901
LOAD
B
C
D
A
LINE
12
34
UV
E
TB901
AC100V-240V
TE901
FG
CD9
01
R901
H-7ZCRD0920
H-7ZCRD0921
H-7ZCRD0919
CBA-357
B901
CB901
C901 C902 C903
LF901
Menu Index
C.1 Main .......................................................................................................C-1
C.2 PI ............................................................................................................C-5
C.3 TT ...........................................................................................................C-7
C.4 AIS .........................................................................................................C-8
C.5 AZ ..........................................................................................................C-9
C.6 Track ....................................................................................................C-10
C.7 Route ...................................................................................................C-11
C.8 U.Map ..................................................................................................C-12
C.9 Serviceman Menu ...............................................................................C-14
Appendix C
Menu Index
JMA-9100 Instruction Manual > C.Menu Index > C.1 Main
C－1
C
C.1 Main
├1. EBL Maneuver Setting- - - - - - - - - - - - - - - - - - - - - - - - - section 4.1.5 on page 4-14
│├1. EBL Maneuver
│├2. Reach
│├3. Turn Mode
│└4. Turn Set
├2. File Manager - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.11.1 on page 3-120
├3. RADAR Menu
│├1. Process Setting - - - - - - - - - - - - - - - - - - - - - - - - section 3.8.1 on page 3-91
││├1. Video Latitude - - - - - - - - - - - - - - - - - - - - section 3.8.1.1 on page 3-91
││├2. Video Noise Rejection - - - - - - - - - - - - - - - - section 3.8.1.2 on page 3-92
││├3. AUTO Dynamic Range - - - - - - - - - - - - - - - section 3.8.1.3 on page 3-92
││├4. Process Switch - - - - - - - - - - - - - - - - - - - section 3.8.1.4 on page 3-93
││├5. 2nd Process Mode- - - - - - - - - - - - - - - - - - section 3.8.1.5 on page 3-93
││├6. Process Switch Rrange - - - - - - - - - - - - - - - section 3.8.1.6 on page 3-93
││├7. Fast Target Detection - - - - - - - - - - - - - - - - section 3.8.1.7 on page 3-94
││├8. User Function Setting - - - - - - - - - - - - - - - - -section 3.9.3 on page 3-113
│││├1. Function1 Setting
││││├1. Mode - - - - - - - - - - - - - - - - - - - - - - - - page 3-113
││││├2. IR
││││├3. Process
││││├4. Target Enhance
││││├5. AUTO Sea/Rain
││││├6. Save Present State
││││├9. Next
││││├1. Pulse Length 0.75nm - - - - - - - - - - - - - - - - page 3-115
││││├2. Pulse Length 1.5nm
││││├3. Pulse Length 3/4nm
││││├4. Pulse Length 6/8nm
││││├5. Pulse Length 12nm
││││├6. Pulse Length 16nm
││││├9. Next
││││├1. Video Latitude - - - - - - - - - - - - - - - - - - - - page 3-115
││││├2. Video Noise Rejection
││││├3. AUTO Dynamic Range
││││├4. Process Switch
││││├5. 2nd Process Mode
││││├6. Process Switch Range
││││├7. Fast Target Detection
││││├9. Next
││││├1. Trails Interval - - - - - - - - - - - - - - - - - - - - page 3-115
││││├2. Trails Mode
││││├3. Trails Reference Level
││││├4. Trails Reduction
││││├6. Trails Process
││││├7. Max Interval
││││├9. Next
││││├1. Gain Offset - - - - - - - - - - - - - - - - - - - - - page 3-115
││││├2. PRF
││││├3. Small Buoy Detection
││││├4. Fishnet Detection
││││├5. Antenna Height
││││├8. Set Mode Default
││││└9. Initialize
│││├2. Function2 Setting
│││├3. Function3 Setting
│││└4. Function4 Setting
││└9. SART - - - - - - - - - - - - - - - - - - - - - - - - - - section 6.5 on page 6-12
│├2. RADAR Trails Setting
││├1. Trails Mode - - - - - - - - - - - - - - - - - - - - - section 3.8.2.1 on page 3-95
││├2. Trails Ref Level - - - - - - - - - - - - - - - - - - - section 3.8.2.2 on page 3-95
││├3. Trails Reduction - - - - - - - - - - - - - - - - - - - section 3.8.2.3 on page 3-96
││├5. Trails Process - - - - - - - - - - - - - - - - - - - - section 3.8.2.4 on page 3-96
C－2
JMA-9100 Instruction Manual > C.Menu Index > C.1 Main
││└6. Max Interval - - - - - - - - - - - - - - - - - - - - - section 3.8.2.5 on page 3-96
│└3. TXRX Setting
││├1. PRF Fine Tuning - - - - - - - - - - - - - - - - - - section 3.8.3.1 on page 3-97
││├2. Stagger Trigger - - - - - - - - - - - - - - - - - - - section 3.8.3.2 on page 3-97
││├4. PRF - - - - - - - - - - - - - - - - - - - - - - - - - section 3.8.3.3 on page 3-97
││└5. Ice Class Standby Mode - - - - - - - - - - - - - - - section 3.8.3.4 on page 3-98
├4. Multi Window Setting
│├1. DIR/DIST EXP Display- - - - - - - - - - - - - - - - - - - - section 3.8.8.1 on page 3-105
│├2. Numeric NAV INFO - - - - - - - - - - - - - - - - - - - - - section 3.8.8.2 on page 3-105
│├3. Depth Graph Setting- - - - - - - - - - - - - - - - - - - - - section 3.8.8.3 on page 3-106
││├1. Depth Graph Display
││├2. Depth Range
││├3. Time Range
││└4. Depth Unit
│├4. Wind Graph Setting - - - - - - - - - - - - - - - - - - - - - section 3.8.8.4 on page 3-107
││├1. Wind Graph Display
││└2. Wind Speed Unit
│├5. TEMP Graph Setting- - - - - - - - - - - - - - - - - - - - - section 3.8.8.5 on page 3-108
││├1. TEMP Graph Display
││├2. TEMP Graph Color
││├3. TEMP Range
│││├1. Temperature setting (MIN)
│││├2. Temperature setting
│││├3. Temperature setting
│││├4. Temperature setting
│││├5. Temperature setting
│││└6. Temperature setting (MAX)
││└4. Time Range
│└6. Course Bar Setting - - - - - - - - - - - - - - - - - - - - - section 3.8.8.6 on page 3-109
││├1. Course Bar Display
││├2. Autopilot Course
││└3. ROT Scale
├5. Map Setting
│├3. JRC/ERC Setting
││├1. Day/Night
││├2. Color of Land
││├3. Bright of Land
││├4. Color of Sea
││├5. Bright of Sea
││├6. Color of Name
││├7. Bright of Name
││├8. Bright of Track/Mark/Line
││├9. Next
││├1. LAT/LON Line
││├2. Color of L/L Line
││└3. Bright of L/L Line
│├5. Map Display Setting
││└3. LAT/LON Correction
│└7. Map Draw AZI Mode
├6. NAV Equipment Setting
│├1. GYRO Setting - - - - - - - - - - - - - section 3.4.14 on page 3-36, section 7.1.7 on page 7-9
│├2. MAG Compass Setting - - - - - - - - - - - - - - - - - - - -section 3.4.16 on page 3-37
││├1. Heading Correction
││└2. Correct Value
│└3. Set/Drift Setting - - - - - - - - - - - - - - - - - - - - - - - section 3.4.16.1 on page 3-38
││├1. Correction
││├2. Set
││└3. Drift
├7. Sub Menu
│├1. Display Color Setting - - - - - - - - - - - - - - - - - - - - section 3.8.5.1 on page 3-99
││├1. Day/Night - - - - - - - - - - - - - - - - - - - - - - section 3.8.5.2 on page 3-100
││├2. Outer PPI
││├3. Inner PPI
││├4. Character
││├5. RADAR Video
││├6. RADAR Trails(Time)
││├8. Target Symbol
││├9. Next
││├1. Cursor
││├2. Range Rings
JMA-9100 Instruction Manual > C.Menu Index > C.1 Main
C－3
C
││├3. EBL/VRM/PI
││└4. Own Symbol/HL/Vector
│├2. Brilliance Setting- - - - - - - - - - - - - - - - - - - - - - - section 3.8.5.3 on page 3-100
││├1. RADAR Video - - - - - - - - - - - - - - - - - - - - section 3.8.5.4 on page 3-101
││├2. RADAR Trails
││├3. Target Symbol- - - - - - - - - - - - - - - - - - - - section 3.8.5.5 on page 3-102
││├4. Range Rings
││├5. EBL/VRM/PI
││├6. Character
││├7. Own Symbol/HL/Vector
││└8. Keyboard
│├3. User Setting
││├1. Load User Setting - - - - - - - - - - - - - - - - - - section 3.10.1 on page 3-118
││├2. Save User Setting - - - - - - - - - - - - - - - - - - section 3.10.2 on page 3-119
││└3. Delete User Setting - - - - - - - - - - - - - - - - - section 3.10.3 on page 3-119
│├4. Option Key Setting
││├1. Option1 - - - - - - - - - - - - - - - - - - - - - - - -section 3.8.7 on page 3-103
││└2. Option2 - - - - - - - - - - - - - - - - - - - - - - - -section 3.8.7 on page 3-103
│├5. Buzzer Volume - - - - - - - - - - - - - - - - - - - - - - - -section 3.8.6 on page 3-102
││├1. Key ACK
││├2. OPE Miss
││├3. CPA/TCPA Alarm
││├4. New Target Alarm
││├5. Lost Alarm
││├6. Navigation Alarm
││├7. System Alarm
││└8. Inter Switch
│├6. Date/Time Setting - - - - - - - - - - - - - - - - - - - - - - - section 7.2.7 on page 7-20
││├1. UTC/LMT
││├2. LMT Date
││├3. LMT Time
││├4. Time Zone
││├5. Display Style
││└6. Synchronize with GPS
│├7. Screen Capture Setting
││├1. Select Item
│││├1. Graphic
│││├2. RADAR Video
│││├3. RADAR Trails
│││└4. Map
││├2. Select Card Slot
││├3. File Erase
││├4. AUTO Capture Interval
││└5. AUTO File Erase
│├9. EBL/Cursor Setting - - - - - - - - - - - - - - - - - - - - - - - section 4.1.3 on page 4-3
││├1. EBL1 Bearing Fix
││├2. EBL2 Bearing Fix
││└3. Cursor Setting - - - - - - - - - - - - - - - - - - - - - section 4.1.3.3 on page 4-5
│││├1. EBL/VRM Control CURS
│││├2. Cursor Length
│││└4. Cursor Pattern
├8. Plot Setting
│└6. AUTO Backup - - - - - - - - - - - - - - - - - - - - - - - - - section 3.8.9 on page 3-110
├9. Test Menu- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 8.3.1 on page 8-6
│├1. Self Test - - - - - - - - - - - - - - - - - - - - - - - - - - - section 8.3.1.1 on page 8-7
││├1. Memory Test
│││├1. SDRAM
│││├2. SRAM
│││├3. FLASH ROM
│││└4. GRAPHIC
││├2. TXRX Test
││├3. Line Test
││└4. Supply Voltage
│├2. Monitor Test- - - - - - - - - - - - - - - - - - - - - - - - - - section 8.3.1.2 on page 8-9
││├1. Pattern 1
││├2. Pattern 2
││├3. Pattern 3
││├4. Pattern 4
││├5. Pattern 5
││├6. Pattern 6
C－4
JMA-9100 Instruction Manual > C.Menu Index > C.1 Main
││├7. Pattern 7
││└8. Pattern 8
│├3. Keyboard Test- - - - - - - - - - - - - - - - - - - - - - - - - section 8.3.1.3 on page 8-9
││├1. Key Test
││├2. Buzzer Test
││└3. Light Test
│├4. MON Display - - - - - - - - - - - - - - - - - - - - - - - - section 8.3.1.4 on page 8-10
│├5. System Alarm Log - - - - - - - - - - - - - - - - - - - - - - section 8.3.1.5 on page 8-10
│└6. System Information - - - - - - - - - - - - - - - - - - - - - section 8.3.1.6 on page 8-11
└0. EXIT
JMA-9100 Instruction Manual > C.Menu Index > C.2 PI
C－5
C
C.2 PI
├1. Display for All Lines - - - - - - - - - - - - - - - - - - - - - - - - - - section 4.1.4.3 on page 4-9
├2. Operation Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-10
│├All
│├Individual
│├Track
│└Equiangular
├3. Control1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-11
│├All:All2
│├Individual:Sequential
│├Individual:Index Line 1
│├Individual:Index Line 2
│├Individual:Index Line 3
│├Individual:Index Line 4
│├Individual:Index Line 5
│├Individual:Index Line 6
│├Individual:Index Line 7
│├Individual:Index Line 8
│├Track:Group 1
│├Track:Group 2
│├Track:Group 3
│├Track:Group 4
│├Equiangular:Group 1
│├Equiangular:Group 2
│├Equiangular:Group 3
│└Equiangular:Group 4
├4. Floating - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -page 4-11
├5. Heading Link - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -page 4-11
├6. Next
├8. Press EBL Dial to Control PI#3
├9. Press VRM Dial to Move End Point#ii
├1. Range Scale Link - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-12
├2. Reference Bearingi- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-12
│├All:True4
│├All:HL
│├Individual:True
│├Individual:HL
│├Individual:Index Line 1
│├Individual:Index Line 2
│├Individual:Index Line 3
│├Individual:Index Line 4
│├Individual:Index Line 5
│├Individual:Index Line 6
│├Individual:Index Line 7
│├Individual:Index Line 8
│├Track:True
│├Track:HL
│├Track:Index Line 1
│├Track:Index Line 2
│├Track:Index Line 3
│├Track:Index Line 4
│├Track:Index Line 5
│├Track:Index Line 6
│├Track:Index Line 7
│└Track:Index Line 8
├3. Operation Area - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-13
├4. Display for Individual Line - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 4-13
1.The setting items are determined by the setting of Operation Mode.
2.Operating Mode : Control
3.Displayed only when "3. Control" is Individual.
4.Operating Mode : Reference Bearing
JMA-9100 Instruction Manual > C.Menu Index > C.3 TT
C－7
C
C.3 TT
├1. Association Setting - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.4 on page 5-37
│├1. Association
│├2. Proprity
│├3. Bearing
│├4. Range
│├5. Course
│├6. Speed
│└7. Applicable AIS Target
├2. Target Track Setting - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.6.2 on page 5-44
│├1. Target Track Function - - - - - - - - - - - - - - - - - - - - section 5.6.2.2 on page 5-44
│├2. Target Track Color- - - - - - - - - - - - - - - - - - - - - - section 5.6.2.1 on page 5-44
││├1. All
││├2. Target Track No.1
││├3. Target Track No.2
││├4. Target Track No.3
││├5. Target Track No.4
││├6. Target Track No.5
││├7. Target Track No.6
││├8. Target Track No.7
││├9. Next
││├1. Target Track No.8
││├2. Target Track No.9
││├3. Target Track No.10
││└4. Other
│├3. Target Track Display- - - - - - - - - - - - - - - - - - - - - section 5.6.2.4 on page 5-46
││├1. All
││├2. Target Track No.1
││├3. Target Track No.2
││├4. Target Track No.3
││├5. Target Track No.4
││├6. Target Track No.5
││├7. Target Track No.6
││├8. Target Track No.7
││├9. Next
││├1. Target Track No.8
││├2. Target Track No.9
││├3. Target Track No.10
││└4. Other
│├4. Track Memory Interval - - - - - - - - - - - - - - - - - - - - section 5.6.2.5 on page 5-47
│├5. Clear Track Color - - - - - - - - - - - - - - - - - - - - - - section 5.6.2.6 on page 5-47
│├6. Clear Track Number
│└7. File Operations - - - - - - - - - - - - - - - - - - - - - - - section 5.6.2.7 on page 5-48
││├1. Select Card Slot
││├2. Load Mode
││├3. Load - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 5-48
││├4. Save - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 5-49
││├5. Erase - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 5-51
││└6. Card T.TRK Display - - - - - - - - - - - - - - - - - - - - - - - - - page 5-52
├3. Trial Maneuver - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.7 on page 5-53
│├1. Trial Function
│├2. Course(EBL)
│├3. Speed(VRM)
│├4. Vector Time
│├5. Time to Maneuver
│└6. Own Ship's Dynamic Trait
││├1. Reach
││├3. Turn Radius
││├4. Acceleration
││└5. Deceleration
├4. Target Number Display - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.4 on page 5-18
└9. TT Test Menu - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.7 on page 5-21
│├1. Test Video- - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.7.1 on page 5-22
│├2. TT Simulator - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.7.2 on page 5-23
│├3. Status - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.7.3 on page 5-24
│└4. Gate Display - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.7.4 on page 5-25
C－8
JMA-9100 Instruction Manual > C.Menu Index > C.4 AIS
C.4 AIS
├1. Association Setting - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.4.2 on page 5-37
│├1. Association
│├2. Proprity
│├3. Bearing
│├4. Range
│├5. Course
│├6. Speed
│└7. Applicable AIS Target
├2. Target Track Setting - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.6.2 on page 5-44
│├1. Target Track Function - - - - - - - - - - - - - - - - - - - - section 5.6.2.2 on page 5-44
│├2. Target Track Color- - - - - - - - - - - - - - - - - - - - - - section 5.6.2.1 on page 5-44
││├1. All
││├2. Target Track No.1
││├3. Target Track No.2
││├4. Target Track No.3
││├5. Target Track No.4
││├6. Target Track No.5
││├7. Target Track No.6
││├8. Target Track No.7
││├9. Next
││├1. Target Track No.8
││├2. Target Track No.9
││├3. Target Track No.10
││└4. Other
│├3. Target Track Display- - - - - - - - - - - - - - - - - - - - - section 5.6.2.4 on page 5-46
││├1. All
││├2. Target Track No.1
││├3. Target Track No.2
││├4. Target Track No.3
││├5. Target Track No.4
││├6. Target Track No.5
││├7. Target Track No.6
││├8. Target Track No.7
││├9. Next
││├1. Target Track No.8
││├2. Target Track No.9
││├3. Target Track No.10
││└4. Other
│├4. Track Memory Interval - - - - - - - - - - - - - - - - - - - - section 5.6.2.5 on page 5-47
│├5. Clear Track Color - - - - - - - - - - - - - - - - - - - - - - section 5.6.2.6 on page 5-47
│├6. Clear Track Number
│└7. File Operations - - - - - - - - - - - - - - - - - - - - - - - section 5.6.2.7 on page 5-48
││├1. Select Card Slot
││├2. Load Mode
││├3. Load - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 5-48
││├4. Save - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 5-49
││├5. Erase - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - page 5-51
││└6. Card T.TRK Display - - - - - - - - - - - - - - - - - - - - - - - - - page 5-52
├3. Trial Maneuver - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.7 on page 5-53
│├1. Trial Function
│├2. Course(EBL)
│├3. Speed(VRM)
│├4. Vector Time
│├5. Time to Maneuver
│└6. Own Ship's Dynamic Trait
││├1. Reach
││├2. Turn Radius
││├3. Acceleration
││└4. Deceleration
├4. AIS Filter Setting - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.7 on page 5-32
│├1. Filter Type- - - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.7.2 on page 5-32
│├2. Make AIS Filter - - - - - - - - - - - - - - - - - - - - - - - section 5.3.7.3 on page 5-33
JMA-9100 Instruction Manual > C.Menu Index > C.5 AZ
C－9
C
│├3. Filter Display - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.7.4 on page 5-34
│├4. ENT
│└6. Filter Mode - - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.7.5 on page 5-34
├5. Target Number Display - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.6 on page 5-31
├6. AIS Alarm Setting - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.9 on page 5-36
│├1. Lost Alarm- - - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.9.1 on page 5-36
│└2. CPA/TCPA Alarm - - - - - - - - - - - - - - - - - - - - - - section 5.3.9.2 on page 5-36
├7. Message - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.5.5 on page 5-29
│├1. Addressed Message
│└2. Broadcast Message
├8. Display Lost TGT Data - - - - - - - - - - - - - - - - - - - - - - - section 5.3.5.6 on page 5-31
└9. Own Ship's AIS Data - - - - - - - - - - - - - - - - - - - - - - - - section 5.3.5.7 on page 5-31
C.5 AZ
├1. AZ 1- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.1.1 on page 5-14
├2. AZ 2- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.1.1 on page 5-14
├3. Make AZ 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.1.1 on page 5-14
├4. Make AZ 2 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 5.2.1.1 on page 5-14
└5. ENT
C－10
JMA-9100 Instruction Manual > C.Menu Index > C.6 Track
C.6 Track
├1. DISP Own Track Color - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.2 on page 3-40
│├1. All
│├2. White
│├3. Cyan
│├4. Blue
│├5. Green
│├6. Yellow
│├7. Pink
│└8. Red
├2. Clear Own Track Color - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.5 on page 3-42
├3. Track Type - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.6 on page 3-42
├4. Num/Vector Display - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.6 on page 3-42
├5. File Operations
│├1. Select Card Slot
│├2. Load Mode
│├3. Load
│├4. Save
│├5. Erase
│└6. Card Own Track Display
├6. Water Depth Setting - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.7 on page 3-44
│├1. Depth setting (MIN)
│├2. Depth setting
│├3. Depth setting
│├4. Depth setting
│├5. Depth setting
│└6. Depth setting (MAX)
├7. Water TEMP Setting- - - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.8 on page 3-45
│├1. Temperature setting (MIN)
│├2. Temperature setting
│├3. Temperature setting
│├4. Temperature setting
│├5. Temperature setting
│└6. Temperature setting (MAX)
├8. Current Setting - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.5.9 on page 3-46
│├1. Current Size
│├2. Layer A
│├3. Layer B
│└4. Layer C
JMA-9100 Instruction Manual > C.Menu Index > C.7 Route
C－11
C
C.7 Route
├1. Select Route - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.1 on page 3-67
├2. WPT/Route Settig
│├1. Waypoint Alarm - - - - - - - - - - - - - - - - - - - - - - - section 3.7.4.1 on page 3-79
│├2. Route Alarm - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.4.2 on page 3-80
│├3. Set Route Sequence- - - - - - - - - - - - - - - - - - - - - - section 3.7.2 on page 3-68
││├1. Planned Speed - - - - - - - - - - - - - - - - - - - section 3.7.3.5 on page 3-77
││├2. Add - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.2.2 on page 3-69
││├3. Correct Position - - - - - - - - - - - - - - - - - - - section 3.7.2.3 on page 3-70
││├4. Correct Planned Speed - - - - - - - - - - - - - - - section 3.7.2.4 on page 3-71
││├5. Delete - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.2.5 on page 3-72
││├6. Insert - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.2.6 on page 3-73
││└7. New Monitor Route - - - - - - - - - - - - - - - - - section 3.7.2.1 on page 3-68
│├6. Waypoint Input - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.3 on page 3-75
│├7. Save Temporary Route
│├8. Off-Track Limit Line - - - - - - - - - - - - - - - - - - - - - section 3.7.6.1 on page 3-83
│├9. Next
│├1. SEL. NUM/Comment Size - - - - - - - - - - - - - - - - - - section 3.7.6.2 on page 3-83
│├2. Waypoint Vector- - - - - - - - - - - - - - - - - - - - - - - section 3.7.6.3 on page 3-84
│├3. Status of Origin/DEST - - - - - - - - - - - - - - - - - - - - section 3.7.6.4 on page 3-85
│└4. WPT Number Display - - - - - - - - - - - - - - - - - - - - section 3.7.6.5 on page 3-85
├3. WPT/Route Operations - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.5 on page 3-81
│├1. Route Sequence- - - - - - - - - - - - - - - - - - - - - - - section 3.7.5.1 on page 3-81
│├2. Waypoint Switch Mode - - - - - - - - - - - - - - - - - - - section 3.7.6.6 on page 3-86
│├3. Waypoint Skip - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.5.2 on page 3-82
│├4. Waypoint Back Skip - - - - - - - - - - - - - - - - - - - - - section 3.7.5.2 on page 3-82
│├5. Set/Cancel Waypoint
│└6. Clear WPT/Route Data
├4. File Operations - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.8 on page 3-87
│├1. Select Card Slot - - - - - - - - - - - - - - - - - - - - - - - section 3.7.8.1 on page 3-87
│├2. Load - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.8.3 on page 3-88
│├3. Save - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.8.2 on page 3-87
│└4. Erase - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.7.8.4 on page 3-89
C－12
JMA-9100 Instruction Manual > C.Menu Index > C.8 U.Map
C.8 U.Map
├1. Own Ship Position - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.3.1 on page 3-52
├2. Edit User Map - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.3 on page 3-52
│├1. Make with Cursor - - - - - - - - - - - - - - - - - - - - - - section 3.6.1.1 on page 3-47
││├1. Type
││└2. Color
│├2. Make with L/L - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.1.3 on page 3-49
││├1. Type
││├2. Color
││├3. L/L
││├4. Comment
││├5. Enter
││└9. New Line Input/9.New Mark Input
│├3. Move - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.3.2 on page 3-53
│├4. Delete - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.3.3 on page 3-55
│├5. Insert/Move Vertex - - - - - - - - - - - - - - - - - - - - - section 3.6.3.4 on page 3-56
│├6. Delete Vertex - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.3.6 on page 3-58
│└7. Delete by Type by Color - - - - - - - - - - - - - - - - - - - section 3.6.3.7 on page 3-59
├3. Shift - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.4.1 on page 3-60
├4. Shift Clear - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.4.2 on page 3-61
├5. Mark Display Setting- - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.2 on page 3-50
│├1. Display Mark Type- - - - - - - - - - - - - - - - - - - - - - section 3.6.2.1 on page 3-50
││├1. All
││├2. ○
││├3. △
││├4. ▽
││├5. □
││├6. ◇
││├7. Wreck (mark)
││├8. △△
││├9. Next
││├1. ▽▽
││├2. △▽
││├3. ▽△
││├4. ＋
││├5. ×
││├6. Ｙ
││├7. Hand drum (mark)
││├8. Light house (mark)
││├9. Next
││├1. Trapezoid（mark）
││├2. filled Trapezoid（mark）
││├3. Hat(mark)
││├4. ●●
││├5. ●
││├6. Filled Triangle(mark)
││├7. ！
││├8. anchor(mark)
││├9. Next
││├1. slash-anchor(mark)
││├2. circle-dotted line(mark)
││├3. non-dangerous wreck(mark)
││├4. ◎
││├5. mariner's event mark(mark)
││├6. ・
││├7. Wavy line (mark)
││├8. Solid line (mark)
││└9. Dashed-dotted line (mark)
│├2. Display Mark Color - - - - - - - - - - - - - - - - - - - - - section 3.6.2.2 on page 3-51
││├1. All
││├2. White
││├3. Cyan
││├4. Blue
JMA-9100 Instruction Manual > C.Menu Index > C.8 U.Map
C－13
C
││├5. Green
││├6. Yellow
││├7. Pink
││└8. Red
│├3. Mark Size - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.2.3 on page 3-51
│└4. Comment Font Size - - - - - - - - - - - - - - - - - - - - - section 3.6.2.4 on page 3-52
├6. Geodetic - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.6 on page 3-65
└7. File Operations - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.5 on page 3-61
│├1. Select Card Slot
│├2. Load Mode - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.5.1 on page 3-61
│├3. Load - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.5.1 on page 3-61
│├4. Unload - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.5.2 on page 3-62
│├5. Save - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.5.3 on page 3-62
│├6. Erase - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 3.6.5.4 on page 3-63
│└7. Card Mark Display - - - - - - - - - - - - - - - - - - - - - - section 3.6.5.5 on page 3-64
C－14
JMA-9100 Instruction Manual > C.Menu Index > C.9 Serviceman Menu
C.9 Serviceman Menu
├Serviceman Menu - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.1.1 on page 7-1
├1. Adjust Menu
│├1. Tune Adjustment - - - - - - - - - - - - - - - - - - - - - - - - section 7.1.3 on page 7-5
│├2. Bearing Adjustment - - - - - - - - - - - - - - - - - - - - - - - section 7.1.4 on page 7-7
│├3. Range Adjustment - - - - - - - - - - - - - - - - - - - - - - - - section 7.1.5 on page 7-7
│└4. TXRX Adjustment
││├1. Antenna Height - - - - - - - - - - - - - - - - - - - - - section 7.1.8 on page 7-9
││├2. Tune Peak Adjustment- - - - - - - - - - - - - - - - - section 7.1.3.1 on page 7-5
││├3. Tune Indicator Adjust - - - - - - - - - - - - - - - - - section 7.1.3.2 on page 7-6
││├4. MON Adjustment - - - - - - - - - - - - - - - - - - section 7.3.4.1 on page 7-31
││├5. MON Indicator Adjustment - - - - - - - - - - - - - - section 7.3.4.2 on page 7-32
││└6. Output Pulse - - - - - - - - - - - - - - - - - - - - - section 7.2.4 on page 7-18
├2. Installation Menu
│├1. Installation Information- - - - - - - - - - - - - - - - - - - - - section 7.2.8 on page 7-21
││├1. Date
││├2. Name
││└3. Company
│├2. Master/Slave - - - - - - - - - - - - - - - - - - - - - - - - section 7.2.5.1 on page 7-19
│├3. Sector Blank- - - - - - - - - - - - - - - - - - - - - - - - - - section 7.2.2 on page 7-16
││├1. Sector1 - - - - - - - - - - - - - - - - - - - - - - - section 7.2.2.1 on page 7-16
││├2. Sector2 - - - - - - - - - - - - - - - - - - - - - - - section 7.2.2.1 on page 7-16
││├3. Sector3 - - - - - - - - - - - - - - - - - - - - - - - section 7.2.2.1 on page 7-16
││├4. Make Sector1 - - - - - - - - - - - - - - - - - - - - section 7.2.2.2 on page 7-16
││├5. Make Sector2 - - - - - - - - - - - - - - - - - - - - section 7.2.2.2 on page 7-16
││└6. Make Sector3 - - - - - - - - - - - - - - - - - - - - section 7.2.2.2 on page 7-16
│├4. CCRP Setting - - - - - - - - - - - - - - - - - - - - - - - - - section 7.1.9 on page 7-10
│├5. COM Port Setting - - - - - - - - - - - - - - - - - - - - - - - section 7.2.1 on page 7-12
││├1. Baud Rate- - - - - - - - - - - - - - - - - - - - - - section 7.2.1.1 on page 7-12
│││├1. COMPASS
│││├2. MAINTENANCE/LOG
│││├3. NAV1
│││├4. NAV2
│││├5. ALARM
│││├6. JARPA
│││├7. AIS
│││├8. BRIDGE NET
│││├9. Next
│││├1. ARPA
│││└2. COM
││├2. RX Port - - - - - - - - - - - - - - - - - - - - - - - section 7.2.1.2 on page 7-13
│││├1. GPS
│││├2. DLOG
│││├3. Alarm
│││├4. Depth
│││├5. Temperature
│││├6. Wind
│││├7. Current
│││├8. ROT
│││├9. Next
│││└1. RSA
││├3. RX Sentence - - - - - - - - - - - - - - - - - - - - section 7.2.1.3 on page 7-14
│││├1. GPS(LL/COG/SOG)
│││├2. GPS(WPT/TIME)
│││├3. Depth
│││├4. Wind
│││└5. Current
││││├1. Data Set Number
││││├2. Layer A
││││├3. Layer B
││││└4. Layer C
││├4. TX Port - - - - - - - - - - - - - - - - - - - - - - - section 7.2.1.4 on page 7-15
│││├1. TTM(TT)
JMA-9100 Instruction Manual > C.Menu Index > C.9 Serviceman Menu
C－15
C
│││├2. TLL(TT)
│││├3. TTD(TT)
│││├4. TLB(TT)
│││├5. OSD
│││├6. RSD
│││├7. ALR
│││├8. ACK
│││├9. Next
│││├1. TTM(AIS)
│││├2. TLL(AIS)
│││├3. TTD(AIS)
│││├4. TLB(AIS)
│││├5. Remote Maintenance
│││├6. JRC-ARPA
│││├7. NMEA0183 Output Format
│││├8. NMEA0183 Talker
│││├9. Next
│││├1. NMEA0183 TX Interval
│││├2. APB
│││├3. BOD
│││├4. GGA
│││├5. GLL
│││├6. RMC
│││├7. RMB
│││├8. VTG
│││├9. Next
│││├1. XTE
│││├2. BWC
│││├3. HDT
│││└4. THS
││├7. Line Monitor
│││├1. COMPASS
│││├2. MAINTENANCE/LOG
│││├3. NAV1
│││├4. NAV2
│││├5. ALARM
│││├6. JARPA
│││├7. AIS
│││├8. BRIDGE NET
│││├9. Next
│││├1. ARPA
│││├2. COM
│││├3. TXRX/ISW
│││├4. KEYBOARD1
│││└5. KEYBOARD2
│├6. Alarm System - - - - - - - - - - - - - - - - - - - - - - - - - section 7.2.9 on page 7-22
││├1. Watch Alarm
│││├1. Reset Interval - - - - - - - - - - - - - - - - section 7.2.9.1 on page 7-22
│││└2. Trackball Threshold - - - - - - - - - - - - - section 7.2.9.2 on page 7-22
││├2. Relay Output - - - - - - - - - - - - - - - - - - - - section 7.2.9.3 on page 7-23
│││├1. Relay Output Mode
│││├2. TT CPA/TCPA
│││├3. AIS CPA/TCPA
│││├4. New Target
│││├5. Lost
│││└6. RADAR Alarm
││├3. ALR Output - - - - - - - - - - - - - - - - - - - - - section 7.2.9.4 on page 7-23
│││├1. System Alarm
│││└2. TT/AIS Alarm
││├4. Sound Output Mode - - - - - - - - - - - - - - - - - section 7.2.9.6 on page 7-25
││├5. External ACK Setting - - - - - - - - - - - - - - - - section 7.2.9.5 on page 7-24
│││├1. Critical Alarm
││││├1. Audio
││││├2Indication
││││└3. Acknowledge State
│││├2. Normal Alarm
││││├1. Audio
││││├2. Indication
││││└3. Acknowledge State
│├7. Inter Switch
C－16
JMA-9100 Instruction Manual > C.Menu Index > C.9 Serviceman Menu
││├1. ISW Install
││├2. Mask Setting
│││├1. No.1 Connection/No.1 Master
│││├2. No.2 Connection/No.2 Master
│││├3. No.3 Connection/No.3 Master
│││├4. No.4 Connection/No.4 Master
│││├5. No.5 Connection/No.5 Master1
│││├6. No.6 Connection/No.6 Masteri
│││├7. No.7 Connection/No.7 Masteri
│││└8. No.8 Connection/No.8 Masteri
││└3. S-ISW TXRX Power Supply
│├8. Language - - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.2.6 on page 7-20
│├9. Next
│├1. Input BP Count - - - - - - - - - - - - - - - - - - - - - - - section 7.2.5.2 on page 7-19
│├2. TNI Blank - - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.2.3 on page 7-17
││├1. TNI Blank - - - - - - - - - - - - - - - - - - - - - - section 7.2.3.1 on page 7-17
││└2. Make Sector- - - - - - - - - - - - - - - - - - - - - section 7.2.3.2 on page 7-17
│├3. Device Installation - - - - - - - - - - - - - - - - - - - - - - - - section 7.1.6 on page 7-8
││├1. Gyro
││├2. Compass
││├3. GPS Compass
││├4. LOG
││├5. 2AXW
││├6. 2AXG
││└7. GPS
│├4. Network
││├1. Network Function
││└2. IP Address
├3. Maintenance Menu
│├1. Safety Switch - - - - - - - - - - - - - - - - - - - - - - - - - section 7.4.1 on page 7-33
│├2. Area Initial- - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.4.2 on page 7-34
││└1. Partial Master Reset - - - - - - - - - - - - - - - - - section 7.4.2.1 on page 7-34
│││├1. Serviceman Menu
│││├2. Except Serviceman Menu
│││├3. User Setting
│││├4. TT Setting
│││├5. AIS Setting
│││├6. Day/Night
│││└7. JRC Card Copy Record
││└2. All Master Reset- - - - - - - - - - - - - - - - - - - section 7.4.2.2 on page 7-34
│├3. Internal To Card2 - - - - - - - - - - - - - - - - - - - - - - section 7.4.3.1 on page 7-35
│├4. Card2 To Internal - - - - - - - - - - - - - - - - - - - - - - section 7.4.3.2 on page 7-35
│├5. TXRX Time - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.4.4 on page 7-36
││├1. Clear TX Time- - - - - - - - - - - - - - - - - - - - section 7.4.4.1 on page 7-36
││├2. Clear Motor Time - - - - - - - - - - - - - - - - - - section 7.4.4.2 on page 7-36
││├3. TXRX to Display Unit - - - - - - - - - - - - - - - - section 7.4.4.3 on page 7-37
││└4. Display Unit to TXRX - - - - - - - - - - - - - - - - section 7.4.4.4 on page 7-37
│└6. String Data Update - - - - - - - - - - - - - - - - - - - - - - section 7.4.5 on page 7-38
└9. RADAR/TT Initial Setup
│├1. Signal Processing - - - - - - - - - - - - - - - - - - - - - - - section 7.3.1 on page 7-26
││├1. Echo Noise Level - - - - - - - - - - - - - - - - - - section 7.3.1.1 on page 7-26
││└2. Setting Mode - - - - - - - - - - - - - - - - - - - - section 7.3.1.2 on page 7-27
│├2. TT- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.3.2 on page 7-27
││├1. Vector Constant - - - - - - - - - - - - - - - - - - - section 7.3.2.1 on page 7-27
││├2. Video TD Level - - - - - - - - - - - - - - - - - - - section 7.3.2.2 on page 7-28
││├3. Video High Level
││├4. Video Low Level
││├5. Gate Size
││└6. Limit Ring
│└3. MBS- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - section 7.3.3 on page 7-29
││├1. MBS Level- - - - - - - - - - - - - - - - - - - - - - section 7.3.3.1 on page 7-29
││└2. MBS Area - - - - - - - - - - - - - - - - - - - - - - section 7.3.3.2 on page 7-30
1.Only for ISW Extended Mode
MARINE RADARMARINE RADAR
EQUIPMENTEQUIPMENT
INSTRUCTIONINSTRUCTION
MANUALMANUAL
JMA-9133-SAJMA-9133-SA
JMA-9132-SAJMA-9132-SA
JMA-9123-7XA/9XAJMA-9123-7XA/9XA
JMA-9122-6XA/9XA/6XAHJMA-9122-6XA/9XA/6XAH
JMA-9110-6XA/6XAHJMA-9110-6XA/6XAH
01ETM ISO 9001, ISO 14001 Certified
Printed in Japan
Marine Service Department
+81-3-3492-1305
+81-3-3779-1420
tmsc@jrc.co.jp
Telephone :
Facsimile :
e-mail :
AMSTERDAM Branch
Telephone :
Facsimile :
e-mail :
+31-20-658-0750
+31-20-658-0755
service@jrcams.nl
SEATTLE Branch
Telephone :
Facsimile :
e-mail :
+1-206-654-5644
+1-206-654-7030
service@jrcamerica.com
CODE No.7ZPRD0685CODE No.7ZPRD0685
MAY. 2008 Edition 2 JRCMAY. 2008 Edition 2 JRC
Not use the asbestos
For further information,contact:
URL http://www.jrc.co.jp