Japan Radio Co NKE2044 MARINE RADAR User Manual 4

Download:
Mirror Download [FCC.gov]
Document ID	2182311
Application ID	gDuCG4MS/JgxkUoxI3C7FA==
Document Description	User Manual 4
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	154.23kB (1927880 bits)
Date Submitted	2014-01-31 00:00:00
Date Available	2014-01-31 00:00:00
Creation Date	2014-01-06 13:53:06
Producing Software	GPL Ghostscript 9.07; modified using iTextSharp™ 5.4.2 ©2000-2012 1T3XT BVBA (AGPL-version)
Document Lastmod	2014-01-06 13:54:32
Document Title	User Manual 4
Document Creator	CubePDF

Chapter 8
DETAIL PERFORMANCE SETTING
8-1-1 MAIN BANG SUPPRESSION
(Usually, doesn’t need set up. adjust if necessary)
This adjustment is decrease the transmitted signal which appears as a circular echo around the
center.
Adjustment is done so as to main bang is observe slightly seen.
Excess adjusting is danger for nearest small target observation.
If the main bang is not so big, use as factory setting.
100
Chapter 8
DETAIL RFORMANCE SETTING
8-1-2 TARGET EXPANSION
Level setting.
The level which can be set up is level 1, the level 2, the level 3, and the level 4.
Expansion and the magnifying the observation target size..
Tap the “Level1, Level2, Level3, Level4“ icon.
8-1-3 GAIN LEVEL
(Important adjustment. Since adjusted in factory, adjustment is not necessary in the field.)
101
Chapter 8
DETAIL PERFORMANCE SETTING
8-1-4 SEA CLUTTER LEVEL
(Important adjustment. Since adjusted in factory, adjustment is not necessary in the field.)
102
Chapter 8
DETAIL RFORMANCE SETTING
8-1-5 RAIN AND SNOW CLUTTER LEVEL
(Important adjustment. Since adjusted in factory, adjustment is not necessary in the field.)
103
Chapter 8
DETAIL PERFORMANCE SETTING
8-1-6 RADAR Alarm LEVEL
Set up Alarm 1 Level
Set up Alarm 2 Level
104
Chapter 8
DETAIL RFORMANCE SETTING
8 - 2 T T( T A RG E T T R AC KI N G) F U NC TI O N
(Important adjustment. Since adjusted in factory, adjustment is not necessary in the field.)
Vector shows the movement of the target.
Vector Constant large. Vector is stable, but the response is slow.
Vector Constant small. Vector is unstable, but the response is quick..
Tap Vector Constant, setting Bar appears lower part of
screen.
Set up by flick or tap + -.
Rotary knob adjusting is possible. Click and set.
Gate Display:
The region automatically search target moving area.
ON: Confirmation is possible under green searching area.
OFF: Doesn’t display automatically searching area.
105
Chapter 8
DETAIL PERFORMANCE SETTING
Gate Size:
Set up the region size which can search the moving target automatically.
Wide region:
Possible to track fast moving target, but many clutters are include.
Sometime do miss tracking because of much noise.
Narrow region
Possible to track stable, but fast moving target are tend to lost.
Because of first target soon goes outside of the region.
106
Chapter 8
DETAIL RFORMANCE SETTING
8 - 3 S C A NN E R F U N CT IO N
8-3-1 PULSE REPETITION FREQUENCY FINE TUNING (PRF ADJUST)
When existing the same frequency radar, in the same area, they interfere each other.
If p.r.f.(pulse reputation frequency)is the same, Interference can’t reject on the screen.
In that case shift the p.r.f. a little may decrease the radar interference.
PRF Fine Tuning:
If radar interference cannot reject completely, it is effective way to shift the PRF.
Watching the screen echo, rotate the
Rotary knob and stop when radar
interference are fade out from screen.
107
Chapter 8
DETAIL PERFORMANCE SETTING
8-3-2 STAGGER TRIGGER
When existing the same frequency radar, in the same area, they interfere each other.
If p.r.f.(pulse reputation frequency)is the same, Interference can’t reject on the screen.
Another way to decease interference is shift the transmitting time randomly.
Not synchronize signal which transmit randomly is eliminate.
So decrease the other radar interference echo on screen.
ON Stagger: Stagger trigger is generated
OFF Stagger: Stagger trigger stop. (Normal trigger timing)
Select and Tap
Watching the screen echo, select off or on
when heavy radar interference on screen.
return to the menu
108
Chapter 8
DETAIL RFORMANCE SETTING
8-3-3 SCANNER ROTATIONAL SPEED
The rotational speed of inside microwave radiator is possible to change.
The sensitivity of radar are low speed is more higher.
So scanner rotation speed is possible to change according observing range.
Every pulse length can select the Antenna rotation speed.
Short range uses short pulse (SP).
Medium range uses medium pulse (MP)
Long range uses Long pulse (LP)
Shorter range requires the High speed refresh screen.
Longer range requires the Low speed for High sensitivity.
User can select rotational speed according to his request.
109
Chapter 8
DETAIL PERFORMANCE SETTING
8-3-4 ECONOMY MAGNETRON SETUP (PRF , PULSE LENGTH)
The life of magnetron proportion to the total transmitting pulse power.
Low power transmission makes magnetron life more longer.
Selection
Normal:
It is the usual factory setup. Usually, this is chosen.
Economy: Selected the shorter pulse, repeat frequency is also selected lowest 650 Hz.
The life of a magnetron keeps more longer time.
Sensitivity is decrease somewhat from Normal.
High Power: High sensitivity high performance.
Select and Tap
return to the menu
8-3-5 TIMED TX
The life of magnetron proportion to the total transmitting pulse power.
Timed TX can save magnetron life longer.
110
Chapter 8
DETAIL RFORMANCE SETTING
8-3-6 TUNE PEAK LEVEL
Normally, adjustment is not necessary.
(In case of adjustment the tuning peak point is shifted from maximum echo point.)
This adjustment must be done with (8-3-7 Tuning indicator) alternately.
Set RANGE at 24NM
Display tuning level indicator menu.
Tune maximum echo point.
At this point adjust tuning level, so as to seen within the green bar.
Adjusting data is 0 to 127
8-3-7 TUNE INDICATOR LEVEL
Normally, adjustment is not necessary.
(Adjust ,in case of tuning level is too low.)
Set RANGE at 24NM
Display the Tune Indicator menu.
Tuning region is 0 to 127
NOTE! If tuning level is too excess setting, can’t work automatic tuning function.
Adjust the tuning level bar moves within 80 to 90%.
111
Chapter 8
DETAIL PERFORMANCE SETTING
8 - 4 C O N T RO L
8-4-1 BEARING REFERENCE
Select Bearing Mode
True or Relative
8-4-2 BUZZER
Set up the Buzzer sound Level.
112
Chapter 8
DETAIL RFORMANCE SETTING
Set up the Every sound Level.
113
Chapter 8
DETAIL PERFORMANCE SETTING
8 - 5 M AI N T EN A N C E S E T TI N G
8-5-1 SYSTEM TIME CLEAR
8-5-2 SCANNER TIME CLEAR
Clear System time
Clear Scanner time.
114
Chapter 8
DETAIL RFORMANCE SETTING
115
Chapter 8
DETAIL PERFORMANCE SETTING
8 - 6 S Y S T EM S E T TI NG
Set up the operating mode.
8-6-1 MASTER/SLAVE/DEMO
Mode selection of display.
Master: control scanner.(Stand alone.).
Slave: Receive another radar signal and display. can’t
control scanner.
Demo: When use as carrying out the demonstration
Select Master
8-6-2 Own Ship Outline
Set up the Own ship’s Outline, length and scanner position.
116
Chapter 8
DETAIL RFORMANCE SETTING
8-6-3 UNIT
Display units, such as distance, speed, depth of water, water temperature, and wind velocity.
“NM”,” km”,” ktn”, etc. are possible to set up.
117
Chapter 8
118
DETAIL PERFORMANCE SETTING
Chapter 8
DETAIL RFORMANCE SETTING
8-6-4 MOVE OWN SHIP
Means of Moving own ship.
Select
GPS, LOG, Dead Reckoning (dead-reckoning navigation), etc.
119
Chapter 8
DETAIL PERFORMANCE SETTING
8-6-5 USE RANGE SELECT
Select the using unit. “NM”,”KM”,”SM”.
Select the using NM range “ON”.
Not using range, set up “OFF”.
120
Chapter 8
DETAIL RFORMANCE SETTING
Select the using KM range “ON”.
Not using range, set up “OFF”.
Select the using SM range “ON”.
Not using range, set up “OFF”.
121
Chapter 8
DETAIL PERFORMANCE SETTING
8 - 7 DI S P L A Y S C R E EN
Various display setting..
Select the using SM range “ON”.
Not using range, set up “OFF#.
8-7-1 OWN VECTOR DISPLAY
Select the Own Vector display ON or OFF.
8-7-2 ST-BY DISP SELECT
Selections whether at stand by state, display the numeric data on screen or not.
Select the ST-BY Display. “Normal” “Graphical” “Numeric”.
122
Chapter 8
“Normal”
“Graphical”
DETAIL RFORMANCE SETTING
“Numeric”.
8-7-3 OPERATION NUMERICAL DISPLAY
Select the Display. OFF or ON
8-7-4DISPLAY COLOR
Setting of screen color.
123
Chapter 8
DETAIL PERFORMANCE SETTING
Black screen color.
Blue screen color.
White screen color.
Select Brilliance Level
124
Chapter 8
DETAIL RFORMANCE SETTING
Select Character Color
Select Color
Select Brilliance.
Select Brilliance. Level.
Select Echo Color
Select Brilliance. Level.
125
Chapter 8
DETAIL PERFORMANCE SETTING
Select Trails(Time) Color
Select Brilliance. Level.
Select Trails(All) Color
Select Brilliance. Level.
126
Chapter 8
DETAIL RFORMANCE SETTING
Select Own Ships Color
Select Brilliance. Level.
Select Target (TT/AIS) Color
Select Brilliance. Level.
127
Chapter 8
DETAIL PERFORMANCE SETTING
Select EBL/VRM Color
Select Brilliance. Level.
Select Range Ring Color
Select Brilliance. Level.
128
Chapter 8
DETAIL RFORMANCE SETTING
Select Cursor Color
Select Brilliance. Level.
Select AZ/Alarm Color
Select Brilliance. Level.
129
Chapter 8
DETAIL PERFORMANCE SETTING
8-7-5WAYPOINT DISPLAY
Select Waypoint Display.
Select Waypoint Display “ON” or ”OFF”.
8-7-6AIS FILTER
Set up AIS Filter Range.
Select AIS Filter
130
Chapter 8
DETAIL RFORMANCE SETTING
8 - 8 E R R OR A L A RM M AS K
Ignore the unnecessary error signal’s alarm.
8-8-1 SCANNER
The error signal generated in the scanner.
131
Chapter 8
DETAIL PERFORMANCE SETTING
Scanner(Data)
Scanner(Video)
Scanner(Azi)
Scanner(HL)
Scanner(Heater)
132
Scanner(Trigger)
Scanner(MHV)
Chapter 8
DETAIL RFORMANCE SETTING
8-8-2 DISPLAY UNIT
The error signal generated in the display unit.
Display Unit(Video)
Display Unit(Trigger)
Display Unit(AZI)
133
Chapter 8
DETAIL PERFORMANCE SETTING
Display Unit(HL)
COM Port
134
Display Unit(DSP)
Chapter 8
DETAIL RFORMANCE SETTING
8-8-3 CONNECTION DEVICE
The error signal generated about the connected device.
Gyro(Time Out)
Log (Time Out)
GPS (Time Out) are the same method.
135
Chapter 8
DETAIL PERFORMANCE SETTING
8-8-4 RX DATA
The error signal about receiving data from another equipment.
Compass data Alarm
136
Log data Alarm
2Axis Log data Alarm
Chapter 8
Course / Speed data Alarm
Wind data Alarm
Depth data Alarm
Rate of Turn data Alarm
DETAIL RFORMANCE SETTING
Temperature data Alarm
2Rudder data Alarm
WPT data Alarm
LAT/LON data Alarm
Datum data Alarm
Status data Alarm
HDOP data Alarm
AIS data Alarm
137

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Modify Date                     : 2014:01:06 13:54:32-08:00
Create Date                     : 2014:01:06 13:53:06-08:00
Metadata Date                   : 2014:01:06 13:54:32-08:00
Creator Tool                    : CubePDF
Format                          : application/pdf
Document ID                     : uuid:9c162be4-31c8-4cd0-9432-447c2ed870f1
Instance ID                     : uuid:3e0d6aff-af29-4bdd-bf43-8f2cd62858d6
Producer                        : GPL Ghostscript 9.07; modified using iTextSharp™ 5.4.2 ©2000-2012 1T3XT BVBA (AGPL-version)
Has XFA                         : No
Page Count                      : 38
Creator                         : CubePDF

EXIF Metadata provided by EXIF.tools