Japan Radio Co NKE2632 Solid State S-Band Marine Radar User Manual Installation Manual Part 2

Download:
Mirror Download [FCC.gov]
Document ID	2791035
Application ID	o6LERARSP56i/cSy+lEJSg==
Document Description	Installation Manual Part 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	243.11kB (3038838 bits)
Date Submitted	2015-10-22 00:00:00
Date Available	2015-10-22 00:00:00
Creation Date	2015-10-15 14:50:54
Producing Software	iTextSharp™ 5.5.0 ©2000-2013 iText Group NV (AGPL-version); modified using iTextSharp™ 5.5.0 ©2000-2013 iText Group NV (AGPL-version)
Document Lastmod	2015-10-15 14:51:01
Document Title	Installation Manual Part 2
Document Creator	PScript5.dll Version 5.2.2
Document Author:	admin

2.Installation of Scanner Unit > 2.4 PRECAUTIONS
Fig 2-14 The permissible bending radius of coaxial cable
2-38
2.Installation of Scanner Unit > 2.4 PRECAUTIONS
2.4.3 Scanner installation position
1)
Physical selection criteria
• Install the scanner at the center of the mast on the keel line.
• If the scanner cannot be installed at the above position for some reason, the amount of deviation
must be minimized. And, reinforce the mount base and the platform and take precautions to protect
the scanner from vibration and impact at the installation position.
To avoid the radiating section coming in contact with other installed objects while it is rotating, ensure
that there is at least 200 millimeters from the swing circle (turning radius) to other installed objects
(Fig 2-15 Installation of scanner). The swing circle of the JMR-7200/9100 radar's scanner is as
shown in Table 2-5 Swing circle. See “SN.1/Circ.271 6.2(b)”.
Fig 2-15 Installation of scanner
Table 2-5 Swing circle
Scanner unit (length)
Swing circle
NKE-2103-6/6HS (6ft)
1910mm
NKE-1125-6
(6ft)
NKE-2254-6HS
(6ft)
NKE-1129-7 (7ft)
2270mm
NKE-2632/H (8ft)
2770mm
NKE-1125-9
(9ft)
2825mm
NKE-1129-9
(9ft)
NKE-1130/1139
NKE-1632
(12ft)
4000mm
(12ft)
2-39
2.Installation of Scanner Unit > 2.4 PRECAUTIONS
•
Avoid having a rope or signal flag from winding around the radiating section thereby
preventing it from rotating.
•
•
Avoid the effects of dust and heat caused by smoke from a chimney.
•
Provide for maintenance space: platform, safety link, hand rail, steps, etc. The lower
edge of a radar antenna should be a minimum of 500 mm above any safety rail. See
“SN.1/Circ.271 6.1(b)”.
•
When installing the scanner, select a location where there are the fewest structural
objects in the surrounding area so that the capability to drive the motor will not be
depressed by the non-equability wind which is likely to rotate the scanner.
When determining the appropriate scanner height and installation location, take into
consideration the reduction of vibration, the strength of the hull and the scanner mount
base, and maintenance properties.
2) Electrical selection criteria
•
The installation height of the scanner relates to the maximum detection distance. The
higher, the better. However, if it is too high, radio wave energy greatly attenuates
above the scanner's vertical beam width (the point -3dB from the peak of the main
lobe). As a result, it is difficult to detect a close-in target. Sea clutter also increases.
Determine the installation height by taking into consideration the weight, maximum
length of the cable, and maintenance after installation. See “SN.1/Circ.271 6.3(b), 7.1”.
•
If the installation height of the scanner is low, it is difficult to detect a long distance
target. The ship's mast, derrick, and chimney interfere with radiating beam causing
the range that cannot be viewed on the radar display to increase.
Generally, the lowest scanner installation position is supposed to be on the A-B line shown in
Fig 2-16 Lowest scanner installation height.
In the case of the JMR-7210/7225/9210/9225 type radar, 2θ equals 20 .
In the case of the JMR-7230/7272/7282/9230/9272/9282 type radar, 2θ equals 25 . Specifically,
the scanner position is normally elevated so that the chimney and the shrine-gate type mast do
not interfere with radiating beam.
The A-B line, or L line of sight from the radar antenna to the bow of the ship should hit the
surface of the sea in not more than 500 m or twice the ship length, depending which value is
smaller, for all load and trim conditions.
See “SN.1/Circ.271 6.3(a)”.
JMR-7210 / 7225 / 9210 / 9225
：θ=10°
JMA-7230 / 7272 / 7282 / 9230 / 9272 / 9282 ：θ=12.5°
θ
Fig 2-16 Lowest scanner installation height
2-40
2.Installation of Scanner Unit > 2.4 PRECAUTIONS
• If it is considered that sufficient installation height cannot be provided when the scanner is installed directly on the roof of the wheelhouse, use a mounting rack or radar mast (Fig 2-17
Mounting rack and mast for the scanner). Normally, when the scanner installation height
is less than 2 meters from the roof of the wheelhouse, provide a mounting rack assembled at an
angle frame to install the scanner. When the scanner installation height is 2 meters or higher
from the roof of the wheelhouse, provide a cylindrical radar mast to install the scanner. Consider the convenience of the service staff who take care of installation, maintenance, adjustment,
and repair of the scanner by providing adequate footholds to the mounting rack and the radar
mast.
Fig 2-17 Mounting rack and mast for the scanner
•
When installing the scanner, select a location where there are the fewest structural objects in
the surrounding area so that false echoes which interfere with target detection will not be
generated by signal reflection from other scanners, deck structures, and cargo. Only as a
guide, note that structural objects should not exist within the range of the vertical beam width
(Fig 2-18 Scanner and the surrounding structural objects). See “SN.1/Circ.271 6.2(a)”.
Vertical beam width of X-band: Approx. 20
( 10.0
when the height of the radiating section is 0 )
Vertical beam width of S-band: Approx. 25
( 12.5
when the height of the radiating section is 0 )
Fig 2-18 Scanner and the surrounding structural objects
2-41
2.Installation of Scanner Unit > 2.4 PRECAUTIONS
•
When installing two or more scanners, scanners in close proximity should have a
minimum vertical elevation separation angle of 20 and a minimum vertical separation of
1m where possible, so that those scanners do not enter each other's vertical beam
width range. See “SN.1/Circ.271 6.1(c)”.
•
To avoid interference with other equipment and to prevent radio noise from generating,
do not place the VHF antenna, GPS antenna, and INMARSAT's dome within the range
of the vertical beam width. See “SN.1/Circ.271 6.1(a)”.
•
Keep a record of installation height data. The data is necessary for the initial setting
of the display unit.
•
Minimize the blind sector, and ensure the adequate view angle so that the blind sector
does not exist in the range 22.5 from side to rear (Fig 2-19 Ensuring view angle).
Specifically, ensure a sufficient view field in the straight front (relative bearing 000 ).
See “SN.1/Circ.271 6.3(c)”.
•
Individual blind sectors of more than 5, or a total arc of blind sectors of more than 20,
should not occur in the remaining arc, excluding the arc in Fig 2-19 Ensuring view
angle. See “SN.1/Circ.271 6.3(d)”.
•
For radar installations with two radar systems, where possible, the antennas should be
placed in such a way as to minimize the blind sectors. See “SN.1/Circ.271 6.3(e)”.
Fig 2-19 Ensuring view angle
•
Magnetron which has strong magnetic force is included in the scanner. Install the
scanner at least 6 meters away from nautical instruments including magnetic
compasses and chronometers. See “SN.1/Circ.271 6.2(c), 7(c)”.
2-42
2.Installation of Scanner Unit > 2.4 PRECAUTIONS
*If there is a concern that structural objects existing within the vertical beam width may generate false
echo, equip the structural objects with a radio wave absorber. (There are two types of absorbers:
broadband type having no specific resonant frequency and narrowband type which can absorb a band
with a specific frequency. Use those where applicable.) Furthermore, it is effective to install a metal
reflector, which reflects radio waves upwardly, between the scanner and a structural object so that the
radar's radio wave will not directly come in contact with the structural object.
When the structural objects exist in the surrounding area of Scanner unit, the false echo may appear.
The sector blank function is effective to reduce the signal reflection from the structural objects. Because
it can stop transmission. Therefore, it may reduce the false echo appearance.
Because most radio wave absorbers have poor durability, some must be replaced every
year. When installing a reflector, the area to the rear of the reflector becomes a blind
sector. Therefore, minimize the size of the reflector.
When the sector blank function set to on, ensure a sufficient view field in the straight front.
*The above procedures for selecting an scanner installation position are described based on the radar's
scanner. Comprehensively select the scanner position by considering other scanners' installation
procedure manual, hull's structure, strength of the selected position, and vibration.
2.4.4 Confirmation during test run
If the scanner vibrates a lot during test run, try to reduce or prevent vibration by reinforcing the
scanner mount base or using wire stays attached to the radar mast.
2.4.5 Others
•
The design of the mounting platform for the scanner should take into account the
vibration requirements of resolution A.694(17) and furthermore defined by IEC 60945.
See “SN.1/Circ.271 7(d)”.
Vibration 2 to 13.2Hz
Amplitude
13.2 to 100Hz Acceleration
+/-1mm +/-10%
7m/s2
•
All installations should facilitate protection of equipment, including cabling, from
damage.
•
The cables should be kept as short as possible to minimize attenuation of the signal.
See “SN.1/Circ.271 7.2(b)”.
•
Crossing of cables should be done at right angles(90°) to minimize magnetic field
coupling. See “SN.1/Circ.271 7.2(e)”.
•
Eliminating the interference on frequencies used for marine communications and
navigation due to operation of the radar. All cables of the radar are to be run away from
the cables of radio equipment. (ex. Radiotelephone. Communications receiver and
direction finder, etc.) Especially inter-wiring cables between scanner unit and display
unit of the radar should not be run parallel with the cables of radio equipment. See
“SN.1/Circ.271 7.2(h)”.
•
Cable, coaxial cable and flexible wave guide should not be exposed sharp bends. See
also section 2.4.2 (4) “3) Permissible bending radius”. See “SN.1/Circ.271 7.2(g)”.
•
The grounding of equipment units should be carried out according to 0
•
Installation for the specified scanner
Receiver See “SN.1/Circ.271 7.2(i)”.
2-43
model and 2.3 Installation of Transmitter
3 Installation of Display Unit > 3.1 Confirmation of Various Units
3. Installation of Display Unit
3.1 Confirmation of Various Units
3.1.1
In case of JMR-9200Series/JAN-9201/JAN-9202
Standard equipment
Stand alone type
NCM-928
Control Unit
NDC-1590
NBD-913
NCE-5605
CENTRAL CONTROL UNIT
(CCU)
POWER SUPPLY UNIT
(PSU)
TRACKBALL OPERATION UNIT
(TOPU)
CWA-246
26inch DISPLAY UNIT MOUNT KIT
Desktop type
CWB-1595
NCM-928
26inch Desktop Frame
Control Unit
CWB-1596
OPU Desktop Frame
NDC-1590
NBD-913
NCE-5605
CENTRAL CONTROL UNIT
(CCU)
POWER SUPPLY UNIT
(PSU)
TRACKBALL OPERATION UNIT
(TOPU)
Desktop type cable
CML-901-F
DISPLAY UNIT
INTERCONNECTION(F)
Select equipment
NWZ-208
NCE-5625
26inch MONITOR UNIT
(26 inch MNU)
KEYBOARD OPERATION UNIT
(KOPU)
or
or
NWZ-208-TP
CWB-1593
26inch TOUCH PANEL
MONITOR UNIT
(26 inch T.P. MNU)
LARGE TRAY
Option equipment
NQE-1143
JUNCTION BOX
(JB)
NQA-2443
SENSOR LAN SWITCH UNIT
QUINT-PS/1AC/24DC/20
QUINT-BAT/24DC/3.4AH
QUINT-DC-UPS/24DC/20
ME-MAX-NEF/QUINT20
UPS
Fig3-1: JMR-9200Series/JAN-9201/JAN-9202 Equipment
3-1
3 Installation of Display Unit > 3.1 Confirmation of Various Units
3.1.2
In case of JMR-7200 Series/JAN-7201/JAN-7202
Standard equipment
Stand alone type
NCM-928
Control Unit
NDC-1590
NBD-913
NCE-5605
CENTRAL CONTROL UNIT
(CCU)
POWER SUPPLY UNIT
(PSU)
TRACKBALL OPERATION UNIT
(TOPU)
CWA-245
19inch DISPLAY UNIT MOUNT KIT
Desktop type
CWB-1594
NCM-928
19inch Desktop Frame
Control Unit
CWB-1596
OPU Desktop Frame
NDC-1590
NBD-913
NCE-5605
CENTRAL CONTROL UNIT
(CCU)
POWER SUPPLY UNIT
(PSU)
TRACKBALL OPERATION UNIT
(TOPU)
Desktop type cable
CML-901-F
DISPLAY UNIT
INTERCONNECTION(F)
Select equipment
NWZ-207
NCE-5625
19inch MONITOR UNIT
(19 inch MNU)
KEYBOARD OPERATION UNIT
(KOPU)
or
or
NWZ-207-TP
CWB-1593
19inch TOUCH PANEL
MONITOR UNIT
(19 inch T.P. MNU)
LARGE TRAY
Option equipment
NQE-1143
JUNCTION BOX
(JB)
NQA-2443
SENSOR LAN SWITCH UNIT
QUINT-PS/1AC/24DC/20
QUINT-BAT/24DC/3.4AH
QUINT-DC-UPS/24DC/20
ME-MAX-NEF/QUINT20
UPS
Fig 3-2: JMR-7200Series/JAN-7201/JAN-7202 Equipment
3-2
3 Installation of Display Unit > 3.2 Confirmation of Various Interface Boards
3.2 Confirmation of Various Interface Boards
NQE-1143 Junction Box (JB) consists of interface boards that correspond with the suffix.
Type of interface board is as follow.
Interface board
CMH-2370(PC810)
Serial LAN Interface
Circuit(SLC)
CMJ-560(PC840)
Analog Option
Circuit(AOC)
CMJ-554(PC820)
Gyro Interface
Circuit(GIF)
CQD-2273(PC830)
Radar Interface
Circuit(RIF)
Fig 3-3: Outline of Interface board
Table 3-1: Definition of the JB Type
Therefore, the type of JB :「NQE-1143-SAGR」is shown that JB consists of SLC, AOC, GIF and RIF.
3-3
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
3.3 Selecting the Location for Installation
Determine the installation location of the display unit by considering following conditions:
1) Consider size of each unit that described in outline drawing, and install them which it is possible to
insert a cable from the installation and the base of the bolt.
2) Do not place obstructions around the front side of the unit so that a user can eject a DVD and USB.
3) To decrease an influence over the magnetic compass, separate from the compass by more than 3.0m at
least. See “SN.1/Circ.271 7(c)”.
4) Eliminating the interference on frequencies used for marine communications and navigation due to
operation of the radar. All cables of the radar are to be run away from the cable of radio equipment. (Ex.
Radiotelephone, communications receiver and direction finder. Etc…)
Especially inter-wiring cables between scanner unit and display unit of the radar should not be run
parallel with the cable of radio equipment.
5) Install the monitor unit so that when the user is looking ahead, the lookout view is not obscured. See
“SN.1/Circ.271 7.4(b)”.
6) Away from spray of seawater or rainwater from windows or doors of bridge.
7) Don't install near the equipment which generates the place, and the heat which gets the direct sunlight.
8) Establish a next-page, considering an equipped position to the reference.
Confirm the position of cable inlet for Display Unit Mount Kit(CWA-245, CWA-246).
- 3.3.10 Outline Drawings of CWA-246 26inch Display Unit Mount Kit
- 3.3.11 Outline Drawings of CWA-245 19inch Display Unit Mount Kit
3-4
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
3.3.1
Outline Drawings of NWZ-208 26inch Monitor Unit
Fig 3-4: Outline Drawings of NWZ-208 26inch Monitor Unit
3-5
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
3.3.2
Outline Drawings of NWZ-207 19inch Monitor Unit
Fig 3-5: Outline Drawings of NWZ-207 19inch Monitor Unit
3-6
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
3.3.3
Outline Drawings of NCE-5605 Trackball Operation Unit
Fig 3-6: Outline Drawings of NCE-5605 Trackball Operation Unit
3-7
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
3.3.4
Outline Drawings of NCE-5625 Keyboard Operation Unit
Fig 3-7: Outline Drawings of NCE-5625 Keyboard Operation Unit
3-8
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
3.3.5
Outline Drawings of CWB-1593 Large Tray
Fig 3-8: Outline Drawings of CWB-1593 Large Tray
3-9
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
3.3.6
Outline Drawings of NDC-1590 Central Control Unit
Fig 3-9: Outline Drawings of NDC-1590 Central Control Unit
3-10
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
3.3.7
Outline Drawings of NBD-913 Power Supply Unit
Fig 3-10: Outline Drawings of NBD-913 Power Supply Unit
3-11
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
3.3.8
Outline Drawings of NQE-1143 Junction Box
Fig 3-11: Outline Drawings of NQE-1143 Junction Box
3-12
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
3.3.9
Outline Drawings of NQA-2443 Sensor LAN Switch Unit
Fig 3-12: Outline Drawings of NQA-2443 Sensor LAN Switch Unit
3-13
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
3.3.10 Outline Drawings of CWA-246 26inch Display Unit Mount Kit
Fig 3-13: Outline Drawings of CWA-246 26inch Display Unit Mount Kit
(With display, trackball operation unit and keyboard operation unit installed)
3-14
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
3.3.11 Outline Drawings of CWA-245 19inch Display Unit Mount Kit
Fig 3-14: Outline Drawings of CWA-245 Display Unit Mount Kit
(With display, trackball operation unit and keyboard operation unit installed)
3-15
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
3.3.12 Outline Drawings of CWB-1595 26inch Desktop Frame
Fig 3-15: Outline Drawings of CWB-1595 26inch Desktop Frame
3-16
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
3.3.13 Outline Drawings of CWB-1594 19inch Desktop Frame
Fig 3-16: Outline Drawings of CWB-1594 19inch Desktop Frame
3-17
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
3.3.14 Outline Drawings of CWB-1596 OPU Desktop Frame
Fig 3-17: Outline Drawings of CWB-1596 OPU Desktop Frame
3-18
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
3.3.15 Precautions for transporting and storing the display unit
● A display unit is a heavy load. Be very careful about handing it.
● Do not allow the scanner fall on its side while it is stored or being installed.
● Be careful when transporting display unit to prevent damage to the monitor unit.
● When lifting the 26inch stand alone type Display Unit
- When hoisting the scanner by a crane, do not hoist it by attaching a belt or a rope only to the
handrail of display unit.(See Fig 3-18 Improper way to hoist)
Fig 3-18 Improper way to hoist
- Attach to the display unit the lifting lugs specified and eye bolt. And lift over the rope at four
positons eyebolts. (See Fig 3-19 When the stand alone type display unit(26inch))
Fig 3-19 When the stand alone type display unit(26inch)
3-19
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
● When lifting the 19inch stand alone type Display Unit
- When hoisting the scanner by a crane, do not hoist it by attaching a belt or a rope only to the
handrail of display unit.(See Fig 3-20 Improper way to hoist)
Fig 3-20 Improper way to hoist
- Attach to the display unit the lifting lugs specified and eye bolt. And lift over the rope at four
positons eyebolts. (See Fig 3-21 When the stand alone type display unit(19inch))
Fig 3-21 When the stand alone type display unit(19inch)
3-20
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
3.3.16 Detaching the front frame of the Display unit mount kit
Do not detach the front frame except under unavoidable circumstances
for the sake of the ship's structure. It may lead to unexpected accidents.
Be sure to do it with at least two persons.
If only one person does this work, he/she may lead to unexpected
accidents.
You can pull out the front frame of the Display Unit mount kit if the door of the bridge is too narrow
for Display units.
3-21
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
Dimension diagrams of the Display unit mount kit without a front frame
Dimension diagrams of CWA-246: 26inch Display Unit mount kit without a front frame
Dimension diagrams of CWA-245: 19inch Display Unit mount kit without a front frame
3-22
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
【 Required Tools 】
The tools shown in the following table are required for this work
Table Required Tools
No
Name
Size
Phillips screwdriver
Size #2
Phillips stubby screwdriver
Size #2
Appearance
Do not lose the screws as they will be needed again
Do not detach the front frame except under unavoidable circumstances for the
sake of the ship's structure. It may lead to unexpected accidents.
Step 1
Remove the monitor
Remove the monitor from the Display Unit mount kit on the reverse order of installation.
Refer to the 3.4.1 Installation of Monitor Unit NWZ-208/NWZ-207/NWZ-208-TP/NWZ-207-TP.
3-23
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
Step 2 Remove the Trackball Operation Unit
Remove the Trackball Operation Unit from the Display Unit mount kit on the reverse order of
installation.Refer to the 3.4.2.3 Installation of Trackball Operation Unit (NCE-5605).
It is not necessary to remove Keyboard Operation Unit. (If it has been installed.)
Step 3 Remove Operation Unit frame
Remove the screws (M4: 9 locations) that fasten the Operation Unit frame and then take out it.
Taking out the Operation Unit frame from 26inch Display Unit mount kit
3-24
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
Taking out the Operation Unit frame from 19inch Display Unit mount kit
Step 4 Remove the bottom sheet metal
Remove the bottom sheet metal of Operation Unit frame.
In the 26inch Display Unit mount kit, Remove the screws (M3: 2 locations) that fasten the sheet metal and
then take out it.
Taking out the Operation Unit sheet metal from 26inch Display Unit mount kit
In the 19inch Display Unit mount kit, you can remove the sheet metal and Operation Unit frame together.
3-25
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
Step 5
Remove the front cover and the Junction Box
Remove the front cover from the Display Unit mount kit.
・When the Junction box has been installed
Remove the Junction box from the Display Unit mount kit on the reverse order of installation.
Refer to the 3.5.1 Installation of Junction Box.
3-26
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
Step 6
Remove the front frame
Using a Phillips stubby screwdriver, remove the M4 screws that fasten the front frame. They are 4 locations
in one side, 8 locations in total.
Pull up the front frame slowly in the obliquely upward direction along its line and take away.
3-27
3 Installation of Display Unit > 3.3 Selecting the Location for Installation
After carrying in the Display Unit is completed, assemble to the original condition by repeating the
same procedure in the reverse order. Please make sure to tighten all the screws and connect all the
cables back in place.
This completes carrying in the Display Unit into the bridge that has a narrow door by detaching its front
frame.
3-28
3 Installation of Display Unit > 3.4 Installation of Standard Equipment
3.4 Installation of Standard Equipment
3.4.1
Installation of Monitor Unit NWZ-208/NWZ-207/NWZ-208-TP/NWZ-207-TP
1) Remove the screw covers on the top and bottom spaces in the monitor(NWZ-208 / NWZ-207 /
NWZ-208-TP / NWZ-207-TP).
Monitor unit(26inch) NWZ-208/NWZ-208-TP
Monitor unit(19inch) NWZ-207/NWZ-207-TP
Insert a small flat blade screwdriver into the end of the screw cover and remove the cover by the
principle of leverage. If you try to remove forcibly, the panel will break or unit will damage.
3-29

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : admin
Create Date                     : 2015:10:15 14:50:54-07:00
Modify Date                     : 2015:10:15 14:51:01-07:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2015:10:15 14:51:01-07:00
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Creator                         : admin
Document ID                     : uuid:0d0104a7-b409-4d41-bead-8d5fde0a427d
Instance ID                     : uuid:a8c947c0-e1a6-4609-b846-f8a7911bc908
Producer                        : iTextSharp™ 5.5.0 ©2000-2013 iText Group NV (AGPL-version); modified using iTextSharp™ 5.5.0 ©2000-2013 iText Group NV (AGPL-version)
Page Count                      : 35

EXIF Metadata provided by EXIF.tools