Japan Radio NKE2063 MARINE RADAR User Manual NKE2063UserMan

Japan Radio Co Ltd. MARINE RADAR NKE2063UserMan

Users Manual 2

Chapter 2OPERATIONS2.1SCREEN DISPLAY 2-12INSTRUCTION MANUAL Chapter 2 OPERATIONS 2.1 SCREEN DISPLAY 
Chapter 2OPERATIONS2.2PANEL2-22.2 PANELOperate this equipment with the panel of the Display unit. No. Key  Description ձ MENU Press: Opens/closes the menu. Hold down: Opens the code input screen (the Adjust Menu). ղ CLEARPress: Cancels menu operations. Returns to upper menu.   Stops the alarm sound. ENT Press:  Enters the selected menu item. ճCursor keys  Press:  Selects menu items. Moves the cursor. Hold down: Accelerates cursor movement. մ GAINPress:  Performs the user key 1 function. Hold down: Switches the sensitivity between manual and automatic modes. Turn: Adjusts receiving sensitivity. յ SEAPress:  Performs the user key 2 function. Hold down: Switches the sea clutter suppression function between manual and automatic modes. Turn:  Removes sea clutter. ն RAINPress:  Performs the user key 3 function. Hold down: Switches the rain/snow clutter suppression function between manual and automatic modes. Turn:  Removes rain/snow clutter. շ RANGE  Press:  Switches the range. ո FUNC Press:  Switches function settings. Hold down: Opens the function setting menu. չ BRILL Press: Changes the display brilliance Hold down: Opens the display color menu. պ MULTIPress:  Opens the soft key menu. Turn:  Adjusts the selected mode. Changes the setting values. Selects soft key menu items. ջ USB MEMORY  Saves files. Updates the software. ռ STBYPress:  Turns on this equipment (when it is turned off).   Turns to standby state (when the equipment is transmitting). Press multiple keys: Turns off the equipment when pressed together with the TX/PRF key. ս TX/PRFPress:  Starts transmitting (in standby state)   Tunes the repetition frequency (when transmitting). Hold down: Turns off the heading line. (after preheating finished). վ Soft keys  Press:  Opens the soft key menu.
Chapter 2OPERATIONS2.2PANEL2-32INSTRUCTION MANUAL  Key Operations Press:  Press a key, then release the key before 2 seconds elapse. Hold down:  Press a key, and hold down the key for 2 seconds or more. Press multiple keys:  Press multiple keys simultaneously. Turn:  Turn a control in clockwise/counterclockwise direction.
Chapter 2OPERATIONS2.3POWER ON/OFF 2-42.3 POWER ON/OFF CAUTIONA malfunction may occur if the power in the ship is instantaneously interrupted during operation of the radar. In this case, the power should be turned on again. Note: z  Wait for about 2 seconds before turning on the power again. z  Immediately after the radar is installed, at start of the system after it has not been used for a long time, or after the magnetron is replaced, preheat the equipment in the standby state for 20 to 30 minutes before setting it into the transmit state. z  If the preheating time is short, the magnetron causes sparks, resulting in its unstable oscillation. Start transmission on a short-pulse range and change the range to the longer pulse ranges in turn. If the transmission is unstable in the meantime, immediately place the system back into the standby state and maintain it in the standby state for 5 to 10 minutes before restarting the operation. Repeat these steps until the operation is stabilized.  Power On 1Press the [STBY] key on the display unit to turn on the display unit. The display unit is turned on, and the preheating time screen is displayed. When the preheating time is over, the preheating time screen disappears.
Chapter 2OPERATIONS2.3POWER ON/OFF 2-52INSTRUCTION MANUAL  Starting transmission 1Press the [TX/PRF] key. The radar starts transmission and the antenna starts rotating. Reference:The radar cannot start transmission if you press the [TX/PRF] key while the preheating time is displayed.  Stopping transmission 1Press the [STBY] key on the display unit. The radar stops transmission and the antenna stops rotating. Maintain the standby state if radar observation is restarted in a relatively short time. Only pressing the [TX/PRF] key starts observation.  Power Off 1Press the [STBY] key and the [TX/PRF] key simultaneously. The system is turned off. WARNINGWhen conducting maintenance work, make sure to turn off the power and unplug the power connector J1 of the display unit so that the power supply to the equipment is completely cut off. Some equipment components can carry electrical current even after the power switch is turned off, and conducting maintenance work without unplugging the power connector may result in electrocution, equipment failure, or accidents.
Chapter 2OPERATIONS2.4SENSITIVITY ADJUSTMENT 2-62.4 SENSITIVITY ADJUSTMENT Sensitivity can be adjusted. Adjust the noise on the display unit to achieve better observation state. CAUTIONIf sensitivity is set too high, unnecessary signals such as noises in the receiver and false echoes increase to lower target visibility. At the same time, if sensitivity is set too low, detection of targets such as ships and dangerous objects may be hindered. Therefore, sensitivity must always be set to an optimal level.  Noise Adjustment 1Turn the [GAIN] control. Turn the [GAIN] control clockwise to increase sensitivity. Turn the [GAIN] control counterclockwise to decrease sensitivity. The sensitivity adjustment screen appears when turning the [GAIN] control. Sensitivity can be adjusted between 0 and 100. When turning the [GAIN] control, the gain control indication is stretched or shrunk.
Chapter 2OPERATIONS2.4SENSITIVITY ADJUSTMENT 2-72INSTRUCTION MANUAL z [GAIN] Control Turning the [GAIN] control clockwise increases receiving sensitivity and extends the radar observation range. If the sensitivity is too high, the receiver noise increases reducing the contrast between the targets and the background video. As a result, the targets become obscure on the radar display. To observe densely crowded targets or short-range targets, turn the [GAIN] control counterclockwise to reduce the sensitivity so that the targets are easy to observe. However, be careful not to overlook important small targets. Switching to Manual/Automatic Mode 1Hold down the [GAIN] control. The sensitivity can be switched between manual and automatic modes. The mode is indicated as shown below. 
Chapter 2OPERATIONS2.5SEA CLUTTER SUPPRESSION 2-82.5 SEA CLUTTER SUPPRESSION The sea clutter suppression function suppresses sea clutter returns. CAUTIONWhen using the sea clutter suppression function, never set the suppression level too high canceling out all image noises from the sea surface at close range. Detection of not only echoes from waves but also targets such as other ships or dangerous objects will become inhibited. When using the sea clutter suppression function, make sure to choose the most appropriate image noise suppression level.  Manual Sea Clutter Suppression Function Adjust the sea clutter returns on the display unit to achieve better observation state. 1Turn the [SEA] control. Turn the [SEA] control clockwise to suppress sea clutter returns. Turn the [SEA] control counterclockwise to intensify sea clutter returns. The sea clutter suppression adjustment screen appears when turning the [SEA] control. Sea clutter suppression can be adjusted between 0 and 100. When turning the [SEA] control, the sea clutter control indication is stretched or shrunk.
Chapter 2OPERATIONS2.5SEA CLUTTER SUPPRESSION 2-92INSTRUCTION MANUAL z [SEA] Control The sea clutter suppression function suppresses sea clutter returns by decreasing the receiving sensitivity on a short range. Turn the [SEA] control clockwise to heighten the effect of sea clutter suppression. However, be careful that excessive suppression causes low signal-strength targets such as buoys and boats to disappear from the radar display.  Automatic Sea Clutter Suppression Function Sea clutter suppression can be performed in accordance with the level of sea clutter. Use this automatic mode when sea clutter returns vary in direction. 1Hold down the [SEA] control. Automatic function is selected. Even when the automatic function is selected, you can manually perform fine adjustments by turning the [SEA] control. The sea clutter suppression adjustment screen appears when turning the [SEA]control. Sea clutter suppression can be adjusted between 0 and 100. When the sea clutter suppression (Auto) is set to "0" When the sea clutter suppression (Auto) is set to "10"
Chapter 2OPERATIONS2.5SEA CLUTTER SUPPRESSION 2-10 Canceling Automatic Sea Clutter Suppression Function 1Hold down the [SEA] control. Automatic function is canceled. The mode is indicated as shown below. Reference:When the automatic mode is selected for the sea clutter suppression function, the rain/snow clutter suppression function is switched to the manual mode. The sea clutter suppression function (Auto) and the rain/snow clutter suppression function (Auto) cannot be selected at the same time. 
Chapter 2OPERATIONS2.6RAIN/SNOW CLUTTER SUPPRESSION 2-112INSTRUCTION MANUAL 2.6 RAIN/SNOW CLUTTER SUPPRESSION This function suppresses rain/snow clutter returns. CAUTIONWhen using the sea clutter suppression function, never set the suppression level too high canceling out all image noises from the rain or snow at close range. Detection of not only echoes from the rain or snow but also targets such as other ships or dangerous objects will become inhibited. When using the sea clutter suppression function, make sure to choose the most appropriate image noise suppression level.  Manual Rain/Snow Clutter Suppression Function Adjust the rain/snow clutter returns on the display unit to achieve better observation state. 1Turn the [RAIN] control. Turn the [RAIN] control clockwise to suppress rain/snow clutter returns. Turn the [RAIN] control counterclockwise to intensify rain/snow clutter returns. The rain/snow clutter suppression adjustment screen appears when turning the [RAIN]control. Rain/snow clutter suppression can be adjusted between 0 and 100. When turning the [RAIN] control, the rain/snow clutter control indication is stretched or shrunk.
Chapter 2OPERATIONS2.6RAIN/SNOW CLUTTER SUPPRESSION 2-12z [RAIN] Control When the [RAIN] control is turned clockwise, targets hidden by rain/snow clutter returns appear on the radar display. However, be careful that excessive suppression may cause small targets to be overlooked. Since the rain/snow clutter suppression function also has the effect of suppressing sea clutter, the suppression efficiency improves when using with the [SEA] control. In general, set the value to "0".  Automatic Rain/Snow Clutter Suppression Function Rain/snow clutter suppression can be performed in accordance with the level of rain/snow clutter. Use this automatic mode when rain/snow clutter returns vary in direction.1Hold down the [RAIN] control. Automatic function is selected. Even when the automatic function is selected, you can manually perform fine adjustments by turning the [RAIN] control. The rain/snow clutter suppression adjustment screen appears when turning the [RAIN] control. Rain/snow clutter suppression can be adjusted between 0 and 100. When the rain/snow clutter suppression (Auto) is set to "0" When the rain/snow clutter suppression (Auto) is set to "10"
Chapter 2OPERATIONS2.6RAIN/SNOW CLUTTER SUPPRESSION 2-132INSTRUCTION MANUAL  Switching to Manual/Automatic Mode 1Hold down the [RAIN] control. Automatic function is canceled. The mode is indicated as shown below. Reference:When the automatic mode is selected for the rain/snow clutter suppression function, the sea clutter suppression function is switched to the manual mode. The sea clutter suppression function (Auto) and the rain/snow clutter suppression function (Auto) cannot be selected at the same time. 
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-142.7 SOFT KEY OPERATION This radar can be operated with the soft keys and the MULTI control placed on the front panel of the display unit. You can access to functions without opening the menu screen. To change the default settings, press the [MENU] key to open the menu screen. This section describes the operation with the soft keys and the MULTI control.  Keys for operation y  Soft keys 1, 2, 3 and 4 y [MULTI] control y [CLEAR] key  Soft Key Operations (Example: Opening "Display Screen") This section describes how to operate with the soft keys shown below. yTUNE/PRFyDisplay Screen yTM/RMyBearing Mode yPulse Length yOff Center ySymbol Display yMOByMarkyLineyOwn Track yEvent Mark yAIS Filter yTLL TX
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-152INSTRUCTION MANUAL 1Press the [[MULTI] control. 2Turn the [MULTI] control to select    Display Screen    on the soft key menu.  Reference:When a certain time elapses without any key operation after selecting an item on the soft key menu, the soft key menu and the soft key display automatically disappear. "Display Screen" is color-inverted. Press the [MULTI] control.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-16z Turning the [MULTI] control clockwise To select "Own Track" - "TLL TX" XۂWReference:When the item at the bottom of the soft key menu is color-inverted, the soft key menu does not scroll any more even if the control is turned clockwise. "Own Track" is color-inverted. "Event Mark" is color-inverted. "TLL TX" is color-inverted.  "AIS Filter" is color-inverted.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-172INSTRUCTION MANUAL z Turning the [MULTI] control counterclockwise To select "VRM2" - "EBL1" XۂWReference:When the item at the top of the soft key menu is color-inverted, the soft key menu does not scroll any more even if the control is turned counterclockwise. "VRM2" is color-inverted. "VRM1" is color-inverted. "EBL1" is color-inverted.  "EBL2" is color-inverted.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-18z Soft key 1 The screen changes to the layout set in the section "4.13.7 LOCATION CHANGE" - "1. Screen1". z Soft key 2 The screen changes to the layout set in the section "4.13.7 LOCATION CHANGE" - "2. Screen2". "Screen 1" is color-inverted."Screen 2" is color-inverted.Press the [soft key 1].Press the [soft key 2].
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-192INSTRUCTION MANUAL z Soft key 4 Each time you press the soft key 4 when "Numerical INFO" is set, the soft key display toggles in the following order: "Numerical INFO"  "TT Detail"  "AIS Detail"  "Own AIS INFO"    "MOB INFO". z Closing the soft key menu Press the [CLEAR] key to turn off the soft key menu and the soft key display. z Soft keys 1, 2, 3 and 4   If any of the soft keys is pressed when the soft key menu is turned off, the soft key menu and the soft key display which were displayed previously appear again."Numerical INFO" is color-inverted.Press the [soft key 4].Press any of the soft keys.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-20 "Soft key Operations (Example: Opening "Brilliance") This section describes how to operate with the soft keys shown below. yEBL1yEBL2yVRM1yVRM2yParallel Cursor yVector Length yRADAR Trails yAISyTTyAlarm1 yAlarm2 yBrilliance1Press a soft key. 2Turn the [MULTI] control to select    Brilliance    on the soft key menu.  The soft key menu disappears and "Monitor BRILL" of the soft key display is color-inverted."Brilliance" is activated. Select "Brilliance" and press the control. Press the [MULTI] control.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-212INSTRUCTION MANUAL Reference:Perform the same operations for the other soft key menu items to activate the functions. z Soft key 1 When the soft key 1 is pressed, the display color is switched. z Soft key 2 "Monitor BRILL" is color-inverted, and is activated. Press the [BRILL] key to adjust at eight levels. Also, you can turn the [MULTI] control to change the level. z Setting with the soft key menu To determine the setting of the soft key menu item, press one of the followings:   y [Multi] control y [CLEAR] key The soft key menu item is determined, then the soft key menu and the soft key display are turned off and the setting is finished. "Monitor BRILL" is color-inverted. Press the [soft key 1].Press the [softkey 2]."Monitor BRILL" is color-inverted.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-22z Soft keys 1, 2, 3 and 4   If any of the soft keys is pressed when the soft key menu is turned off, the soft key menu and the soft key display which were displayed previously appear again, and the function is activated. 2.7.1 MEASURING TARGET BEARING (EBL) Measures bearing with EBLs (Electronic Bearing Lines). 1Select  EBL1   EBL2  on the soft key menu. When "EBL1" is selected, the soft key menu is turned off and "BRG Operation" of the soft key display is color-inverted. "EBL1" is activated. When "EBL2" is selected, the soft key menu is turned off and "BRG Operation" of the soft key display is color-inverted. "EBL2" is activated. Select "EBL1" and press the control. Select "EBL2" and press the control. Press any of the soft keys.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-232INSTRUCTION MANUAL 2Operate with the soft keys. Soft key 1:   Display Off   Display "Display Off":  "EBL1"/"EBL2" is not displayed. "Display":  "EBL1"/"EBL2" is displayed. Reference:When "Display Off" is selected for the soft key 1, the equipment performs the followings: y  EBL is not displayed. y  The soft key menu and the soft key display disappears, and EBL function is terminated. Soft key 2:   Floating When pressing the soft key 2, "Floating" is color-inverted. The starting point of the currently operating EBL can be switched from the center of the radar display (floating off) to floating state. Press the cursor keys to move the starting point of "EBL1"/"EBL2". Press the [ENT] key at the starting point of "EBL1"/"EBL2" you want to move. The starting point of "EBL1"/"EBL2" is determined. Reference:The floating position of the EBL’s starting point can be fixed on the radar display or at specific latitude and longitude. Floating function must be turned on to use floating. For details of settings, refer to "2.11.1 SETTING OPERATIONS FOR EBLS (ELECTRONIC BEARING LINES)". Soft key 3:   True   Relative Sets whether to display EBLs (Electronic Bearing Lines) in true bearing mode or relative bearing mode. "True":  "EBL1"/"EBL2" is displayed in true bearing mode. "Relative":  "EBL1"/"EBL2" is displayed in relative bearing mode. Reference:Bearing signal input is required to display true motion. 
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-24Soft key 4:   BRG Operation When "EBL1" or "EBL2" of the soft key menu is selected, "BRG Operation" of the soft key display is color-inverted. Turn the [MULTI] control to change the direction of "EBL1"/"EBL2". To determine the setting of "EBL1"/"EBL2", press one of the followings: the [MULTI] control, the soft key 4 or the [CLEAR] key. The bearing is set and operation state ends. Reference:When "EBL1"/"EBL2" is not selected on the soft key menu, press the soft key 4 to activate the EBL function.  EBL Bearing Display The bearing values of EBL1 and EBL2 displayed on the PPI are indicated at the radar display.Even if EBL1 and EBL2 are not displayed, the bearing values are displayed. 2.7.2 MEASURING RANGE TO TARGET (VRM) Measures the range with VRM (Variable Range Marker). 1Select  VRM1   VRM2  on the soft key menu. When "VRM1" is selected, the soft key menu is turned off and "DIST Operation" of the soft key display is color-inverted. "VRM1" is activated. Select "VRM1" and press the control.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-252INSTRUCTION MANUAL When "VRM1" is selected, the soft key menu is turned off and "DIST Operation" of the soft key display is color-inverted. "VRM2" is activated. 2Operate with the soft keys. Soft key 1:   Display Off   Display "Display Off":  "VRM1"/"VRM2" is not displayed. "Display":  "VRM1"/"VRM2" is displayed. Reference:When "Display Off" is selected for the soft key 1, the equipment performs the followings: y  VRM is not displayed. y  The soft key menu and the soft key display disappears, and VRM function is terminated. Soft key 2:   NM   km   sm Selects units of "VRM1"/"VRM2" range.   Soft key 3: Not available Soft key 4:   DIST Operation When "VRM1" or "VRM2" of the soft key menu is selected, "DIST Operation" of the soft key display is color-inverted. Turn the [MULTI] control to operate "VRM1"/"VRM2". Press the [MULTI] control, the soft key 4 or the [CLEAR] key to determine the "VRM1" and "VRM2" settings. Distance is set and operation state ends. Reference:When "VRM1"/"VRM2" is not selected on the soft key menu, press the soft key 4 to activate the VRM function. Select "VRM2" and press the control.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-26 Variable Range Marker VRM1 is represented as a broken line, and VRM2 as a dotted line. When EBL1 is displayed, VRM1 marker appears on the EBL1. When EBL2 is displayed, VRM2 marker appears on the EBL2. If the starting point of an EBL is offset, the center of a VRM marker is positioned at the starting point of the EBL. 2.7.3 DISPLAYING PARALLEL CURSORS Displays parallel cursors. 1Select    Parallel Cursor    on the soft key menu. The soft key menu disappears and "BRG Operation" of the soft key display is color-inverted."Parallel Cursor" is activated. Select "Parallel Cursor" and press the control.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-272INSTRUCTION MANUAL 2Operate with the soft keys. Soft key 1:   Display Off   Display Displays/hides parallel cursors. "Display Off":  The parallel cursors are not displayed. "Display":  The parallel cursors are displayed. Reference:When "Display Off" is selected for the soft key 1, the equipment performs the followings: y  "Parallel Cursor" is not displayed. y  The soft key menu and the soft key display disappears, and Parallel Cursor function is terminated. Soft key 2:   Floating When pressing the soft key 2, "Floating" is color-inverted. The starting point of the currently operating parallel cursor can be switched from the center of the radar display (floating off) to floating state. Press the cursor keys to move the starting point of "Parallel Cursor". Press the [ENT] key at the starting point of "Parallel Cursor" you want to move. The starting point of "Parallel Cursor" is determined. Reference:The floating position of the parallel cursor starting point can be fixed on the radar display or at specific angle. Floating function must be turned on to use floating. For details of settings, see "2.11.2 SETTING OPERATIONS FOR PARALLEL CURSORS". 
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-28Soft key 3:   True   Relative Sets whether to display parallel cursors in true bearing mode or relative bearing mode. "True":  "Parallel Cursor" is displayed in true bearing mode. "Relative":  "Parallel Cursor" is displayed in relative bearing mode. Reference:Bearing signal input is required to display true motion. Soft key 4:   Bearing   Interval When "Parallel Cursor" of the soft key menu is selected, "BRG Operation" of the soft key display is color-inverted. When "Bearing" is displayed above the soft key 4 Turn the [MULTI] control to change the direction of "Parallel Cursor". Press the soft key 4 to determine the bearing setting of "Parallel Cursor" for length setting. Length setting can be operated. Press the [MULTI] control or the [CLEAR] key when you want to set the bearing only. Bearing is set and operation state ends. When "Interval" is displayed above the soft key 4 Turn the [MULTI] control to change the length of "Parallel Cursor". Press the [MULTI] control, the soft key 4 or the [CLEAR] key to determine the length setting of "Parallel Cursor". Length is set and operation state ends. Reference:When "Parallel Cursor" is not selected on the soft key menu, press the soft key 4 to activate the Parallel Cursor function. 
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-292INSTRUCTION MANUAL 2.7.4 SETTING VECTORS Sets TT and AIS vectors. Reference:The bearing and speed signal input are required to display TT and AIS vectors. 1Select    Vector Length    on the soft key menu. The soft key menu disappears and "Vector Length" of the soft key display is color-inverted."Vector Length" is activated. 2Operate with the soft keys. Soft key 1:   True   Relative Switches between true vector mode and relative vector mode. Soft key 2: Not available Soft key 3: Not available Soft key 4:   Vector Length When "Vector Length" of the soft key menu is selected, "Vector Length" of the soft key display is color-inverted. Vector time can be set in minutes in the range 1 to 60 min. Turn the [MULTI] control to set the vector length. Reference:When "Vector Length" is not selected on the soft key menu, press the soft key 4 to activate the Vector Length function. Select "Vector Length" and press the control.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-30 Vector display Note: z  When a target or own ship changes its course, or when a new target is acquired, its vector may not reach a given level of accuracy until three minutes or more has passed after such course change or target acquisition. Even if three minutes or more has passed, the vector may include an error depending upon the. tracking conditions. A vector to represent a target's predicted position can presented in the True vector or Relative vector mode. In each mode, a vector length can be freely changed for a time interval of 1 to 60 minutes.  Vector Modes z True Vector Mode In the true vector mode, the direction of a target vector indicates the true course of the target and its vector length is proportional to its speed. In this mode, own ship's vector is displayed as shown below. In this mode, the movements of other ships around own ship can be accurately and easily monitored. However, no CPA RING can appear in this mode. The relative vector isnot displayedTrue vectorOwn ship䇻s position HL
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-312INSTRUCTION MANUAL z Relative Vector Mode The relative vector does not represent the true motion of the target, but its relative relation with own ship. This means that a target with its relative vector directed to own ship (passing through the CPA LIMIT ring) will be a dangerous target. In the Relative Vector mode, it can be seen at a glance where the CPA LIMIT of the dangerous target is. The true vector isnot displayedRelative vectorCPA ringHLTherefore, the TRUE/REL mode shall optionally be used for the purpose of observation: the TRUE vector mode for grasping the true aspect of a target, and the REL vector mode for grasping a target's closest point of approach (CPA).  Vector Length The vector length of a target is proportional to its speed, and the vector time can be switched in a range of 1 to 60 minutes. The diagram below illustrates a vector length of a target for six minutes, and the tip of the vector represents the target's position expected to reach six minutes later. 
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-322.7.5 DISPLAYING OTHER SHIP'S TRACKS (RADAR TRAILS)Sets radar trails. Other ships' movements and speeds can be monitored from the lengths and directions of their trails, serving for collision avoidance. 1Select    RADAR Trails    on the soft key menu. The soft key menu disappears and "Trails" of the soft key display is color-inverted. "RADAR Trails" is activated. 2Operate with the soft keys. Soft key 1:   REF Level1   REF Level2   REF Level3   REF Level4 Selects a radar video level required for plotting radar trails. "REF Level1" is the lowest level while "REF Level4" is the highest level. yWhen radar trails are plotted with unwanted waves, change to a higher level. yTo thin radar trails, change to a higher level. yIf radar trails are plotted in snatches, change to a lower level. Soft key 2:   Time/Cont Off   Time/Cont On This function superimpose-displays time radar trails and continuous radar trails. When "Time/Cont Off" is selected, this superimpose-display is disabled. When "Time/Cont On" is selected, this superimpose-display is enabled. Soft key 3:   True   Relative Switches the radar trail display between true and relative motion trail modes. True motion trails: The system plots the absolute motion trails of a target, irrespective of the own ship’s position. The operator can easily judge the course and speed of the target. The system does not plot the trails of land and other fixed targets. Select "RADAR Trails" and press the control.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-332INSTRUCTION MANUAL Relative motion trails: The system plots the trails of a target at a position relative to the own ship.The operator can easily judge whether the target is approaching the own ship. While the own ship is moving, the system also plots the trails when the own ship is turning. Reference:True bearing signal input and speed signal input are required to display radar trails in true motion trail mode. Soft key 4:   Trails When "RADAR Trails" of the soft key menu is selected, "Trails" of the soft key display is color-inverted. Turn the [MULTI] control to change the radar trail length. Reference:When "RADAR Trails" is not selected on the soft key menu, press the soft key 4 to activate the RADAR Trails function. Short:Off/15sec/30sec/1min/2min/3min/4min/5min/6min/10min/15min/All Middle: Off/30sec/1min/2min/3min/4min/5min/6min/10min/15min/All Long:  Off/1min/2min/3min/4min/5min/6min/10min/15min/30min/1hr/All Super Long: Off/30min/1hr/2hr/3hr/4hr/5hr/6hr/10hr/12hr/24hr/All To select the maximum time for displaying radar trails, see Section "2.10 RADAR TRAIL LENGTH SETTING")
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-342.7.6 AIS OPERATIONS The AIS function shows the target's information on the radar display, using other ship's information sent out from the AIS unit. Reference:y  The inputs of heading, latitude/longitude and AIS signal are required to display AIS. y  For detail settings of AIS functions, see "2.15 SETTING TT/AIS". 1Select    AIS    on the soft key menu. The soft key menu disappears and "Target Select" of the soft key display is color-inverted."AIS" is activated. 2Operate with the soft keys. Soft key 1:   Numerical Data   Retrieved Vessel   DEST Ship  "Numerical Data":  The mode is set to AIS numerical data display selection mode. "Retrieved Vessel":  The mode is set to AIS retrieved vessel selection mode. "DEST Ship":  The mode is set to AIS destination ship selection mode Soft key 2:   Setting/Release  AIS data display (numerical display, retrieved vessel and destination ship) can be set/released. Soft key 3:    AIS List    AIS Number SEL   "AIS List":  AIS list is displayed. "AIS Number SEL":  AIS list is not displayed. Soft key 4:   Target Select  When "AIS" of the soft key menu is selected, "Target Select" of the soft key display is color-inverted. Sets the numerical display, retrieved vessel and destination ship. Select "AIS" and press the control.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-352INSTRUCTION MANUAL Reference:When "AIS" is not selected on the soft key menu, press the soft key 4 to activate the AIS function.  AIS Retrieved Vessel AIS retrieved vessel is the function to preferentially display the user-specified ship.  AIS Destination Ship AIS destination ship is the function to display the user-specified ship as the destination.  AIS data (Numerical Data, Retrieved Vessel, DEST Ship) z Displaying AIS data (Operation with the soft key menu) 1Press the cursor keys to select "AIS", then press the [ENT] key. yWhen "Numerical Data" is displayed above the soft key 1 yWhen "Retrieved Vessel" is displayed above the soft key 1 yWhen "DEST Ship" is displayed above the soft key 1 The specified target data is displayed and the symbol is changed. The target data will remain on the radar display until the target is lost, or until another target is designated. Note: z  Numerical Data, AIS retrieved vessel and AIS destination ship can be operated when  Soft key 1:    Numerical Data      Retrieved Vessel      DEST Ship   are selected.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-36z Displaying AIS data (Operation with the [ENT] key) AIS data (numerical display) can be done by the [ENT] key operation without displaying the soft key menu. 1Press the cursor keys to select "AIS", then press the [ENT] key. The selected AIS numerical display is set, and the "AIS" soft key is displayed. Note: z  If operating with the [ENT] key when the soft key menu is closed, the equipment performs the followings: On the AIS symbol:  Opens the AIS soft key and the numerical display of AIS. On the TT symbol:  Opens the TT soft key and the numerical display of TT. Not on the AIS or TT symbol:     Opens the TT soft key, it will be acquired. z  If operating with the [ENT] key when the AIS symbol overlaps the TT symbol, the numerical display of AIS symbol takes priority. Reference:y  After setting the AIS numerical display, perform the same operations in "ە Displaying AIS data (Operation with the soft key menu)". y  AIS data (numerical data) is displayed when the soft key 4 is set to "AIS Detail" in the section "2.7.11 SETTING DISPLAY SCREEN". z Releasing AIS data display 1Press the cursor keys to select "AIS", then press the [ENT] key. Numerical Data, AIS retrieved vessel and AIS destination ship are canceled.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-372INSTRUCTION MANUAL  Displaying the other AIS data Reference:y  AIS retrieved vessel can be set by specifying MMSI number. For details of settings, see "2.15.8 SETTING AIS RETRIEVED VESSEL". y  AIS destination ship can be set by specifying MMSI number. For details of settings, see "2.15.7 SETTING AIS DESTINATION SHIP". z Displaying AIS data 1Turn the [MULTI] control to select "AIS", then press the soft key 3 "Setting/Release".yWhen "Numerical Data" is displayed above the soft key 1 yWhen "Retrieved Vessel" is displayed above the soft key 1 yWhen "DEST Ship" is displayed above the soft key 1 The specified target data is displayed and the symbol is changed. The target data will remain on the radar display until the target is lost, or until another target is designated. When the target for the numerical display is set, "#" is displayed in the AIS list. "#" disappears when the target is released.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-38When the AIS retrieved vessel is set, "*" is displayed in the AIS list. "*" disappears when it is released. When the AIS destination ship is set, "$" is displayed in the AIS list. "$" disappears when it is released. Reference:AIS data (Numerical Data) is displayed when the soft key 4 is set to "AIS Detail" in the section "2.7.11 SETTING DISPLAY SCREEN" Note: z  Numerical Data, AIS retrieved vessel and AIS destination ship can be operated when  Soft key 1:    Numerical Data      Retrieved Vessel      DEST Ship   are selected. z Releasing AIS data display 1Turn the [MULTI] control to select "AIS", then press the soft key 3 "Setting/Release".Numerical Data, AIS retrieved vessel and AIS destination ship are canceled.  AIS Symbols This section describes types and definitions of AIS symbols. Symbol Definition  Remarks Activated AIS target This symbol shows the position of an AIS target on the PPI. The shape is an isosceles triangle, and its vertex shows the approximate heading direction. If heading bearing information or COG information is not received, the target is displayed toward PPI. Selection When selecting an AIS target to display its numeric information, this symbol is superimpose-displayed on the selected target. This is displayed with a split square (basic color is white). AIS SART  This symbol shows the position of an AIS SART target on the PPI.This is displayed with a circle and cross lines.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-392INSTRUCTION MANUAL  Setting AIS Symbol Display For details of displaying/hiding of the AIS symbols, see Section "2.7.16 SETTING SYMBOL ". 2.7.7 TT OPERATIONS The target tracking function calculates the course and speed of a target by automatically tracking the target's move. Note: z  There are the following limitations on use of the target acquisition and target tracking functions. [I]  Resolution between adjacent targets and swapping during automatic target tracking Depending on the particular distance and echo size, resolution between adjacent targets during automatic target tracking usually ranges somewhere between 0.03 to 0.05 NM. If multiple targets approach each other, resolution will become about 0.05 NM and this may cause the system to regard them as one target and thus to swap them or lose part of them. Such swapping or less of targets may also occur if the picture of the target being tracked is affected by rain/snow clutter returns or sea clutter returns or moves very close to land. [II]  Intensity of echoes and the target tracking function The intensity of echoes and the tracking function have a correlationship, and thus the target will be lost if no echoes are detected during seven scans in succession. If a lost target exists, therefore, radar gain must be increased to support detection of the target. If, however, radar gain is increased too significantly, sea clutter returns or other noise may be erroneously detected and tracked as a target, and resultingly, a false alarm may be issued. To execute accurate tracking, it becomes necessary to appropriately adjust the [GAIN], [SEA] and [RAIN] controls of the radar so that the target to be acquired and tracked id clearly displayed on the radar display. Inappropriate settings of these adjustments reduce the reliability / accuracy of automatic tracking.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-40CAUTIONUse the radar only as a navigation aid. The final navigation decision must always be made by the operator him/herself. Making the final navigation decision based only on the radar display may cause accidents such as collisions or running aground.Use the target tracking function (TT) only as a navigation aid. The final navigation decision must always be made by the operator him/herself. Making the final navigation decision based only on the target tracking function (TT) information may cause accidents. The target tracking function (TT) information such as vector, target numerical data, and alarms may contain some errors. Also, targets that are not detected by the radar cannot be acquired or tracked. Making the final navigation decision based only on the radar display may cause accidents such as collisions or running aground.1Select    TT    on the soft key menu. The soft key menu disappears and "Target Select" of the soft key display is color-inverted."TT" is activated. 2Operate with the soft keys. Soft key 1:   Numerical Data   TT Acquisition   TT Release  "Numerical Data":  The mode is set to TT numerical data display selection mode. "TT Acquisition":  The mode is set to TT acquisition selection mode. "TT Release":  The mode is set to TT release selection mode Soft key 2:   Setting/Release  Target tracking data (numerical display) can be set/released. "TT" is color-inverted.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-412INSTRUCTION MANUAL Soft key 3:    TT List    TT Number SEL   "TT List":  TT list is displayed. "TT Number SEL":  TT list is not displayed. Soft key 4:   Target Select  When "TT" of the soft key menu is selected, "Target Select" of the soft key display is color-inverted. Sets the numerical display, TT acquisition and TT release. Reference:When "TT" is not selected on the soft key menu, press the soft key 4 to activate the TT function.  Target acquisition This equipment has automatic acquisition and manual acquisition. z Manual acquisition (Operation with the soft key menu) Note: z  Manual acquisition can be operated when   Soft key 1:    TT Acquisition   are selected. z  If the range is switched, the acquisitions of targets acquired before switching the range are released when those targets get out of the echo radius. 1Press the cursor keys to select the target for acquisition with the cursor, then press the [ENT] key. An initial acquisition symbol appears. After one minute elapses, the target tracking symbol and vector are displayed.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-42Reference:When the number of targets tracked has reached to the maximum (10 targets), any new target is not acquired. Delete the unnecessary targets, then acquire new targets. z Manual acquisition (Operation with the [ENT] key) Target can be acquired by the [ENT] key operation without displaying the soft key menu. Note: z  If operating with the [ENT] key when the soft key menu is closed, the equipment performs the followings: On the AIS symbol:  Opens the AIS soft key and the numerical display of AIS. On the TT symbol:  Opens the TT soft key and the numerical display of TT. Not on the AIS or TT symbol:     Opens the TT soft key, it will be acquired. z  If operating with the [ENT] key when the AIS symbol overlaps the TT symbol, the numerical display of AIS symbol takes priority. 1Press the cursor keys to select the target for acquisition with the cursor, then press the [ENT] key. An initial acquisition symbol appears, and the "TT" soft key is displayed. After one minute elapses, the target tracking symbol and vector are displayed. Reference:y  When operating the [ENT] key on a TT symbol, the "TT" soft key and the target tracking data are displayed. y  When operating the [ENT] key on an AIS symbol, the "AIS" soft key and the selected AIS data (numerical display) are displayed. z Automatic acquisition 1Perform the procedure as shown below to start automatic acquisition. Open  Alarm1   from the soft key menu. Soft key 1:   On Soft key 2:   AZ1
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-432INSTRUCTION MANUAL Reference:y  If untracked targets intrude into the automatic acquisition area in the conditions that maximum number of targets (10 targets) is under tracking, the targets acquired automatically will be cancelled in the order of lower levels of danger. y  For details of automatic acquisition operation, refer to "2.7.8 DISPLAYING THE RADAR ALARM AND AUTOMATIC ACQUISITION OPERATIONS".  Deleting the unnecessary targets Note: z  Releasing manual acquisition can be operated when   Soft key 1:    TT Release   are selected. 1Press the cursor keys to select the target for releasing with the cursor, then press the [ENT] key. The target's vectors and symbols disappear, and only the radar video remains.  Target tracking data (numerical display) Note: z  The numerical display can be operated when   Soft key 1:    Numerical Data   are selected. z Displaying tracking target data (Operation with the soft key menu) 1Press the cursor keys to select the target for the numerical display with the cursor, then press the [ENT] key. The specified target data is displayed and the symbol is changed. The target data will remain on the radar display until the target is lost and its vector disappears, or until another target is designated.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-44Reference:y  If a target with the mark “ۑ” is designated, only its true bearing and range will appear until its vector appears. y  Tracking target data is displayed when the soft key 4 is set to "TT Detail" in the section "2.7.11 SETTING DISPLAY SCREEN" z Displaying tracking target data (Operation with the [ENT] key) The target tracking data can be displayed by the [ENT] key operation without displaying the soft key menu. Note: z  If operating with the [ENT] key when the soft key menu is closed, the equipment performs the followings: On the AIS symbol:  Opens the AIS soft key and the numerical display of AIS. On the TT symbol:  Opens the TT soft key and the numerical display of TT. Not on the AIS or TT symbol:     Opens the TT soft key, it will be acquired. z  If operating with the [ENT] key when the AIS symbol overlaps the TT symbol, the numerical display of AIS symbol takes priority. 1Press the cursor keys to select the target for numerical display with the cursor, then press the [ENT] key. The selected target tracking numerical display is set, and the "TT" soft key is displayed. Reference:After setting the TT numerical display, perform the same operations in "ە Displaying tracking target data (Operation with the soft key menu)". z Releasing tracking target data display 1Press the cursor keys to select the target for the numerical display with the cursor, then press the [ENT] key. Numerical data display is released.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-452INSTRUCTION MANUAL  Displaying the other tracking target data Note: z  The numerical display can be operated when   Soft key 4:    Target Select   are selected. z Displaying tracking target data 1Turn the [MULTI] control to select the target for the numerical display, then press the soft key 3 "Setting/Release". The specified target data is displayed and the symbol is changed. The target data will remain on the radar display until the target is lost and its vector disappears, or until another target is designated. When the target for the numerical display is set, "#" is displayed in the TT list. "#" disappears when the target is released. Reference:y  If a target with the mark “ۑ” is designated, only its true bearing and range will appear until its vector appears. y  Tracking target data is displayed when the soft key 4 is set to "TT Detail" in the section "2.7.11 SETTING DISPLAY SCREEN". z Releasing tracking target data display 1Turn the [MULTI] control to select the target for the numerical display, then press the soft key 3 "Setting/Release". Numerical data display is released.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-46 Target Tracking Symbols This section describes types and definitions of target tracking symbols. Symbol Definition  Remarks Initial acquisition  This symbol is displayed where the target is acquired. This is displayed with a circle of thin dotted line (basic color is white).This symbol is also used for the target acquired automatically. Tracking target  This symbol is displayed for the target which becomes the tracking target after acquired. This is displayed with a circle of thick line (basic color is white).New tracking target  This symbol is displayed for the target which becomes the tracking target after automatically acquired. This is displayed with a circle of thick line (basic color is red).   This is changed to a normal tracking target when acknowledged to new target alarm. Dangerous target  This symbol is displayed when the tracking target becomes a dangerous target with CPA/TCPA decision. This is displayed with a circle of thick line (basic color is red). This blinks while this is not acknowledged. Then, it stops blinking when it is acknowledged. When there are some dangerous targets, targets which is not acknowledged blinks, and targets which has been acknowledged does not blink. Lost  When a tracking target is no longer detected as a target, this symbol is superimpose-displayed on the target symbol. This is displayed with cross lines (basic color is red). This is superimpose-displayed on tracking targets, new tracking targets or dangerous targets. Selection  When selecting a tracking target to display its numeric information, this symbol is superimpose-displayed on the selected target. This is displayed with a split square (basic color is white). This is superimpose-displayed on tracking targets, new tracking targets or dangerous targets.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-472INSTRUCTION MANUAL  Setting Tracking Target Symbol Display For details of displaying/hiding of the tracking target symbols, see Section "2.7.16 SETTING SYMBOL ". 2.7.8 DISPLAYING THE RADAR ALARM AND AUTOMATIC ACQUISITION OPERATIONS With a fan-shaped range made, the radar alarm can give an alarm to ships that enter or depart from the range. 1Select  Alarm1   Alarm2  on the soft key menu. The soft key menu disappears and "Make Zone" of the soft key display is color-inverted."Alarm1" is activated. The soft key menu disappears and "Make Zone" of the soft key display is color-inverted."Alarm2" is activated. "Alarm1" is color-inverted."Alarm2" is color-inverted.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-482Operate with the soft keys. Soft key 1:  When Alarm1 is selected  Off   On   When Alarm2 is selected  Off   On Turns on/off the alarm display. Soft key 2:  When Alarm1 is selected  Sector   Rectangle   AZ1 When Alarm2 is selected  Sector   Rectangle   AZ2  "Sector":Displays a fan-shaped radar alarm. "Rectangle": Displays a rectangle-shaped radar alarm. "AZ1" "AZ2": Displays the acquisition area. Soft key 3:  When Alarm1 is selected  In   Out When Alarm2 is selected  In   Out Sets the alarm issuing conditions for the radar alarm. "In":  An alarm is issued when ship enters. "Out":  An alarm is issued when ship departs. Soft key 4:  When Alarm1 is selected  Make Zone  When Alarm2 is selected  Make Zone  "Make Zone" "Make Zone": When "Make Zone" of the soft key menu is selected, "Target Select" of the soft key display is color-inverted. Reference:When "Alarm1"/"Alarm2" is not selected on the soft key menu, press the soft key 4 to activate the Alarm1/Alarm2 function. 
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-492INSTRUCTION MANUAL  Automatic acquisition operations Reference:If untracked targets intrude into the acquisition area in the conditions that maximum number of targets (10 targets) is under tracking, the targets acquired automatically will be cancelled in the order of lower levels of danger. z Turning on the automatic acquisition 1Perform the following settings. Soft key 1:  When Alarm1 is selected  On   When Alarm2 is selected  On Soft key 2:  When Alarm1 is selected  AZ1   When Alarm2 is selected  AZ2 The acquisition area is activated. An initial acquisition symbol appears for an acquired target. After one minute elapses, the target tracking symbol is displayed. z Turning off the automatic acquisition 1Perform the following settings. Soft key 1:  When Alarm1 is selected  Off   When Alarm2 is selected  Off The acquisition area is deactivated. The acquisition area disappears from the radar screen, however, the tracking target which has been already acquired are continued to be tracked.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-50 Creating a fan-shaped radar alarm/acquisition area 1Perform the following settings. Soft key 2:  When Alarm1 is selected  Sector   AZ1   When Alarm2 is selected  Sector   AZ2 The range setting is started for a fan-shaped radar alarm/acquisition area. 2Press the cursor keys to move the cursor to the first point (setting of the start bearing and range), then press the [ENT] key. 3Press the cursor keys to move the cursor to the second point (setting of the end range), then press the [ENT] key. 
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-512INSTRUCTION MANUAL 4Press the cursor keys to move the cursor to the third point (setting of the end bearing), then press the [ENT] key. 5A fan-shaped radar alarm/acquisition area is determined. Reference:After the fan-shaped radar alarm/acquisition area is determined, the soft key menu and the soft key display disappears, and Alarm1 function is terminated.  Creating a rectangle-shaped radar alarm 1Perform the following settings. Soft key 2:  When Alarm1 is selected  Rectangle   When Alarm2 is selected  Rectangle The range setting is started for a rectangle-shaped radar alarm.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-522Press the cursor keys to move the cursor to the first point (setting of the start latitude and longitude), then press the [ENT] key. 3Press the cursor keys to move the cursor to the second point (setting of the end latitude), then press the [ENT] key. 4Press the cursor keys to move the cursor to the third point (setting of the end latitude), then press the [ENT] key. 
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-532INSTRUCTION MANUAL 5Rectangle-shaped area Rectangle-shaped area is set with Nup as reference. Reference:After the fan-shaped radar alarm/acquisition area is determined, the soft key menu and the soft key display disappears, and Alarm1 function is terminated. 2.7.9 SETTING DISPLAY BRILLIANCE AND DISPLAY COLOR Display brilliance and display color can be changed. 1Select    Brilliance    on the soft key menu. The soft key menu disappears and "Monitor BRILL" of the soft key display is color-inverted."Brilliance" is activated. 2Operate with the soft keys. Soft key 1:   Day1   Day2   Day3   Dusk   Night Display color is changed in accordance with the setting of "Main Menu" - "Display Color". Each time the soft key 1 is pressed when "Day1" is displayed above the soft key 1, the setting changes in order of "Day2"  "Day3"  "Dusk"  "Night". If "Main Menu" - "Display Color" - "Day1" - "Soft Key" is set to "Off", "Day1" is not displayed above the soft key 1. Operate the same way for "Day2", "Day3", "Dusk" and "Night". "Brilliance" is color-inverted.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-54Soft key 2:   Monitor BRILL When "Brilliance" of the soft key menu is selected, "Monitor BRILL" of the soft key display is color-inverted. Press the [BRILL] key to adjust at eight levels. Also, you can turn the [MULTI] control to change the level. Soft key 3: Not available Soft key 4: Not available Reference:When "Brilliance" is not selected on the soft key menu, press the soft key 4 to activate the Brilliance function. 2.7.10 ADJUSTING SCANNER There are automatic tuning mode (AUTO) and manual tuning mode (MAN). In the automatic tuning mode, transmission and receiving frequencies are tuned and adjusted automatically. In the manual tuning mode, tuning is carried out using the MULTI control.1Select    TUNE/PRF    on the soft key menu. The "TUNE/PRF" soft key display appears. 2Operate with the soft keys. Soft key 1:   AUTO Tune   Manual Tune Selects whether to use the tuning function in automatic or manual mode. "TUNE/PRF" is color-inverted.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-552INSTRUCTION MANUAL Soft key 2:   Manual Tuning When pressing the soft key 2, "Manual Tuning" is color-inverted. yWhen "MAN" is displayed above the soft key 1 You can manually adjust using the MULTI control. Turn the MULTI control to adjust tuning. Adjust the video to be the largest by observing the tune indicator bar. Because the tune indicator bar is the guide during manual tuning, adjust the tune indicator bar to the maximum. yWhen "AUTO" is displayed above the soft key 1 "Manual Tuning" is not color-inverted. The equipment automatically adjust tuning. Tuning is adjusted when transmission is started, the range is changed or pulse length is changed. Soft key 3:    PRF Fine Tuning When pressing the soft key 3, "PRF Fine Tuning" is color-inverted. The PRF fine tuning screen appears. Fine-tune the transmitting repetition frequency of the transmitter in the range 90 to 100%. If radar's interference patterns are concentrically displayed, increment or decrement the set value by 3 to 4 in order to heighten the effect of interference rejection.The same operation can be performed by pressing the [TX/PRF] key several times. Use the [MULTI] control to perform PRF fine tuning between 0 and 31. When the soft key 3 "PRF Fine Tuning" is pressed, color-inverted display returns to normal color. Soft key 4: Not available Tune indicator bar
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-562.7.11 SETTING DISPLAY SCREEN Sets the layout of radar screen. 1Select    Display Screen    on the soft key menu. The "Display Screen" soft key display appears. 2Operate with the soft keys. Soft key 1:   Screen1 The screen changes to the layout set with the menu "Adjust Menu" - "Display Screen" - "Location Change" - "Screen1". Soft key 2:   Screen2 The screen changes to the layout set with the menu "Adjust Menu" - "Display Screen" - "Location Change" - "Screen2". Soft key 3: Not available Soft key 4:    Numerical INFO    TT Detail    AIS Detail    Own AIS INFO    MOB INFO Each time you press the soft key 4 when "Numerical INFO" is set, the soft key display toggles in the following order: "Numerical INFO"  "TT Detail"  "AIS Detail"  "Own AIS INFO"    "MOB INFO". "Display Screen" is color-inverted.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-572INSTRUCTION MANUAL  Numerical INFO If "Screen1" has been set in the menu When "Numerical INFO" is displayed above the soft key 4, "Numerical INFO" which has been set in the menu "Screen 1" is displayed. If "Screen2" has been set in the menu When "Numerical INFO" is displayed above the soft key 4, "Numerical INFO" which has been set in the menu "Screen 2" is displayed. Numerical INFONumerical INFO
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-58 TT Detail When "Numerical INFO" is displayed above the soft key 4, press the soft key 4 to display "TT Detail" on the radar screen.  AIS Detail When "TT Detail" is displayed above the soft key 4, press the soft key 4 to display "AIS Detail" on the radar screen. TT DetailAIS Detail
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-592INSTRUCTION MANUAL  Own AIS INFO When "AIS Detail" is displayed above the soft key 4, press the soft key 4 to display "Own AIS INFO" on the radar screen.  MOB INFO When "Own AIS INFO" is displayed above the soft key 4, press the soft key 4 to display "MOB INFO" on the radar screen. Own AIS INFOMOB INFO
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-60 Hiding the heading line 1Hold down the [TX/PRF] key. The ship's heading line is hidden while the [TX/PRF] key is held down. The ship's heading line (HL) that presents the course of own ship is always shown on the radar display. The heading line is hidden while the [TX/PRF] key is held down, so the targets on the heading line can be easily observed. 2.7.12 SWITCHING TO TRUE/RELATIVE MOTION DISPLAY MODESwitches between true and relative motion display modes. Reference:The bearing signal input is required to display true motion. 1Select    TM/RM    on the soft key menu. The "TM/RM" soft key display appears. "TM/RM" is color-inverted.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-612INSTRUCTION MANUAL 2Operate with the soft keys. Soft key 1:   RM Press the soft key 1 to switch to relative motion display. Own ship returns to the center of the radar screen. Soft key 2:   TM Press the soft key 2 to switch to true motion display. Soft key 3:   TM Reset Press the soft key 3 during the true motion display mode, the own ship position is reset, as same as switching from relative motion display to true motion display. Own ship starts from the reset position. Soft key 4: Not available  True motion display In the true motion display mode, the own ship's position on the radar screen moves depending upon its speed and course and the influence of the current. Land and other fixed targets are fixed on the radar screen and only actually moving targets move on the radar screen. When the true motion display mode is selected, the own ship's position is set to 66% of the display radius in the opposite direction to its course allowing for the influence of the current. Own ship starts moving depending upon its speed and course and the influence of the current. Subsequently, when own ship arrives at the position of 66% of the display radius, it is automatically reset to its initial position at 66% of the display radius in the opposite direction to its course allowing for the influence of the current.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-622.7.13 SWITCHING BEARING DISPLAY MODE Selects the azimuth of the radar video. Reference:The bearing signal input is required to display N Up/C Up. 1Select    Bearing Mode    on the soft key menu. The "Bearing Mode" soft key display appears. 2Operate with the soft keys. Soft key 1:   H Up Relative bearing mode [Head Up] is selected. Soft key 2:   N Up True bearing mode [North Up] is selected. Soft key 3:   C Up Course-up bearing mode [Course Up] is selected. Soft key 4:    C Up Reset In Course-up mode, reset the course-up display. "Bearing Mode" is color-inverted.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-632INSTRUCTION MANUAL  Relative Bearing Mode The video is displayed so that the ship's heading line points to the zenith of the PPI (0° on range rings). Since targets are displayed in their directions relative to the ship's heading line, the operator can view the video in the same field of view as in operating the ship at sea. This mode is suitable for watching over other ships.  True Bearing Mode The video is displayed so that the zenith of the PPI (0° on range rings) points to the due north.Fixed targets do not flicker and are easily identified on the chart, and the true bearing of a target can easily be read out. 
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-64 Course-up Bearing Mode By pressing the soft key 3, the own ship's course is fixed pointing to the zenith of the PPI (0° on range rings) points to the due north. In the same way as in the North-up mode, fixed targets do not flicker, and are stabilized even if the ship is yawing. The bearing of the heading line varies by the same shift of own ship's course. To change the course, press the soft key 3 several times to select the Course-up mode, and set a new course. 2.7.14 SELECTING TRANSMITTER PULSE LENGTH Switches the transmitter pulse length. 1Select    Pulse Length    on the soft key menu. The "Pulse Length" soft key display appears. 2Operate with the soft keys. Soft key 1:   SP   MP1   MP2   LP1   LP2 The transmitter pulse length is switched. Press the soft key 1 to change the setting in order of: "SP"  "MP1"  "MP2"  "LP1"  "LP2". "Pulse Length" is color-inverted.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-652INSTRUCTION MANUAL Reference:Options of the transmitter pulse length vary depending on the range. For details, see "7.2 SCANNER". Soft key 2: Not available Soft key 3: Not available Soft key 4: Not available  Effects of transmitter pulse length z  SP  : The transmitter pulse length becomes shorter, and the range resolution improves. The effect of suppressing sea clutter returns and rain/snow clutter returns heightens. Recommended condition for selection: In bays / harbors where targets are densely crowded Rough sea state due to torrential rain or stormy weather z  MP   : The normal transmitter pulse length is set. Both range resolution and sensitivity are appropriately set. Recommended condition for selection: General navigation z  LP  : The transmitter pulse length becomes longer, and sensitivity improves. Small targets are zoomed and are easy to observe. When the sea state is bad, detection performance decreases. Recommended condition for selection: Detection of small targets in good weather conditions Usable transmitter pulse length varies according to the type of scanner unit being used and the observation range being used. For usable pulse length, see the section "SCANNER" in "SPECIFICATIONS".
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-662.7.15 MOVING OWN SHIP’S DISPLAY POSITION The own ship's position can be moved from the display center to any position within 66% of the display radius. This function is convenient for observing a wide coverage in any direction. 1Select    Off Center    on the soft key menu. The "Off Center" soft key display appears. 2Operate with the soft keys. Soft key 1:   Off   On Turns on/off the off center function. "Off":  The own ship's position returns to the center. "On":  The cross cursor mark + will appear at the own ship's position on the radar screen. Soft key 2:   Off Center1   Off Center2   Off Center3   Custom  Load Position "Off Center1":  The own ship's position is moved to 66% position of the display radius. "Off Center2":  Te own ship's position is moved to 44% position of the display radius. "Off Center3":  The own ship's position is moved to 22% position of the display radius. "Custom":  The own ship's position can be moved to any position. When pressing the soft key 4, "Edit" is color-inverted. Move the cross cursor mark + (own ship’s display position) to a desired position by using the cursor keys. Press the ENT key to fix the own ship’s display position at the cross cursor mark + position. "Load Position": The saved own ship’s display position is displayed. "Off Center" is color-inverted.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-672INSTRUCTION MANUAL Soft key 3:   Save Position When "Custom" is displayed above the soft key 2, press the soft key 3 to save the current own ship’s display position. Soft key 4:   Edit When "Custom" is displayed above the soft key 2, press the soft key 4 to move the own ship’s display position to any position. 2.7.16 SETTING SYMBOL DISPLAY Displays/hides the following functions. yTTyAISyMarks/linesyOwn track 1Select    Symbol Display    on the soft key menu. The "Symbol Display" soft key display appears. 2Operate with the soft keys. Soft key 1:    TT Display    TT Display Off "TT Display":  The TT symbols are displayed. "TT Display Off":  The TT symbols are hidden. However, the dangerous targets are shown. Soft key 2:    AIS Display    AIS Display Off "AIS Display":  The AIS symbols are displayed. "AIS Display Off":  The AIS symbols are hidden. Soft key 3:    Mark Display    Mark DISP Off "Mark Display":  The marks and lines are displayed. "Mark DISP Off":  The marks and lines are hidden. Soft key 4:    Track Display    Track DISP Off "Track Display":  The own track is displayed. "Track DISP Off":  The own track is hidden. "Symbol Display" is color-inverted.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-682.7.17 SETTING MOB MOB is the mark of a person or an object overboard. If someone or something falls overboard, set MOB to memorize the latitude/longitude of the location and display the mark. Also, a straight line from the own ship to the mark is displayed. Reference:Bearing signal input and latitude/longitude data input are required to display MOB. 1Select    MOB    on the soft key menu. The "MOB" soft key display appears. 2Operate with the soft keys. Soft key 1:   MOB Setting Sets the MOB at the own ship's position. Soft key 2:   MOB Release The displayed MOB is cleared. Soft key 3: Not available Soft key 4: Not available 2.7.18 MARKINGMarks can be indicated at arbitrary positions on the screen. A mark created on the screen holds the latitude and longitude. Reference:y  Bearing signal input and latitude/longitude data input are required to use marks. y  Up to 200 lines/marks can be displayed for lines, marks and event marks in total. y  When the marks are hidden in "2.7.16 SETTING SYMBOL DISPLAY", marks cannot be created. "MOB" is color-inverted.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-692INSTRUCTION MANUAL 1Select    Mark    on the soft key menu. The "Mark" soft key display appears. 2Operate with the soft keys. Soft key 1:   X  +  Y The mark type of a target is changed. For details of size setting, see "2.17.2 SETTING MARK FUNCTIONS". Soft key 2:   White   Cyan   Blue   Green   Yellow   Pink   Red The mark color of a target is changed. Soft key 3:   Delete Press to delete the marks of selected type/color. Hold down to delete all marks. The confirmation dialog window is displayed. (Marks and event marks are not distinguished when deleting.) Soft key 4:   Off   Enter   Erase   Move You can use the [ENT] key to create/delete/move the marks. "Enter":   Press the [ENT] key to create a mark at the cursor position. "Erase":   Press the [ENT] key to delete a mark at the cursor position. "Move":    Use the cursor to select the mark to be moved and press the [ENT]key. Then move the cursor to select the new position and press the [ENT] key to place the mark. "Mark" is color-inverted.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-702.7.19 USING LINES Lines can be indicated at arbitrary positions on the screen. Reference:y  Bearing signal input and latitude/longitude data input are required to use lines. y  Up to 200 lines/marks can be displayed for lines, marks and event marks in total. 1Select    Line    on the soft key menu. The "Line" soft key display appears. 2Operate with the soft keys. Soft key 1:  ̿̿   - - - -  㸫㸫㸫㸫The line type of a target is changed. Soft key 2:   White   Cyan   Blue   Green   Yellow   Pink   Red The line color of a target is changed. Soft key 3:   Delete Press to delete the lines of selected type/color. Hold down to delete all lines. The confirmation dialog window is displayed. Soft key 4:   Off   Enter   Erase   Move   Insert  You can use the [ENT] key to create/delete/move the lines. "Enter": Press the [ENT] key to create a line at the cursor position. "Erase": Press the [ENT] key to delete a line at the cursor position. "Move":  Use the cursor to select the line to be moved and press the [ENT] key. Then move the cursor to select the new position and press the [ENT]key to place the line. "Insert”:  Use the cursor to select the line to be inserted and press the [ENT] key. Then move the cursor to select the position and press the [ENT] key to insert the line. "Line" is color-inverted.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-712INSTRUCTION MANUAL 2.7.20 DISPLAYING OWN SHIP'S TRACK The own ship's track function saves and displays own ship's track. If navigation equipment is connected, this radar system records latitude/longitude data sent from the navigation equipment and displays own ship's track. For detail settings of own track (clearing own tracks, saved data clearing method, etc), see "2.17.4 DISPLAYING OWN SHIP'S TRACK". Reference:Bearing signal input and latitude/longitude data input are required to display own track. 1Select    Own Track    on the soft key menu. The "Own Track" soft key display appears. 2Operate with the soft keys. Soft key 1:  ̿̿   - - - -  㸫㸫㸫㸫The line type of the own ship's track is changed. Soft key 2:   White   Cyan   Blue   Green   Yellow   Pink   Red The line color of the own ship's track is changed. Soft key 3:   3sec   5sec   10sec   30sec   1min   3min   5min  10min   30min   60min   1NM   3NM   5NM   10NM The storage interval of the own ship's track is changed. A preset time interval or preset distance interval can be selected as the storage interval. The distance setting varies depending on the range scale unit setting. NM range:  1NM, 3NM, 5NM, 10NM km range:  1km, 3km, 5km, 10km sm range:  1sm, 3sm, 5sm, 10sm Soft key 4:   On   Off "On":  This system starts saving the position of the own ship's track. "Off":  This system stops saving the position of the own ship's track. "Own Track" is color-inverted.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-722.7.21 USING EVENT MARKS Displays the event marks. Reference:y  Bearing signal input and latitude/longitude data input are required to display event marks. y  Up to 200 lines/marks can be displayed for lines, marks and event marks in total. y  This function is initially set to off. To use this function, set this to on by referring to "ڦ  Soft Key Menu Setting" in "4.10 Control" of the Installation Manual. 1Select    Event Mark    on the soft key menu. The "Event Mark" soft key display appears. 2Operate with the soft keys. Soft key 1:   X  +  Y The mark type of a target is changed. For details of size setting, see "2.17.2 SETTING MARK FUNCTIONS". Soft key 2:   White   Cyan   Blue   Green   Yellow   Pink   Red The mark color of a target is changed. Soft key 3:   Delete Press to delete the marks of selected type/color. Hold down to delete all marks. The confirmation dialog window is displayed. (Marks and event marks are not distinguished when deleting.) Soft key 4:   Event Mark ENT An event mark is placed at the own ship's position. Reference:You can easily store the event marks, such as fishing spots. Use the cursor to enter the marks for fishing spots, a sinking ship, fish reef, etc. "Event Mark" is color-inverted.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-732INSTRUCTION MANUAL 2.7.22 SETTING AIS FILTER Once the AIS filter is set, only the AIS targets that are inside the filter area are displayed (setting can be made such that AIS targets outside the AIS filter will not be shown). The filter is initially set in a circle having a radius of 20 [NM] from the own ship's position. If 50 or more targets exist in the filter range, they are displayed according to the priority explained in "■ AIS Symbols" of Section "2.7.6 AIS OPERATIONS". Reference:y  Bearing signal input and latitude/longitude data input are required to use AIS functions. y  This function is initially set to off. To use this function, set this to on by referring to "ڦ  Soft Key Menu Setting" in "4.10 Control" of the Installation Manual. 1Select    AIS Filter    on the soft key menu. The "AIS Filter" soft key display appears. 2Operate with the soft keys. Soft key 1:   Off   Range Switches between Off and Range.. "Range":  A filter is set in a circle with a set range as the radius. Soft key 2:   Off   On "Off":  The filter is not displayed. "On":  The filter is displayed. "AIS Filter" is color-inverted.
Chapter 2OPERATIONS2.7SOFT KEY OPERATION 2-742.7.23 USING TLL TX Reference:This function is initially set to off. To use this function, set this to on by referring to "ڦ  Soft Key Menu Setting" in "4.10 Control" of the Installation Manual. Sets the TLL TX. Transmits the TLL sentence of the cursor position on the screen to inform the mark position.1Select    TLL TX    on the soft key menu. The "TLL TX" soft key display appears. 2Operate with the soft keys. Soft key 1:   Off   TLL TX "Off":  TLL sentence is not transmitted with the [ENT] key. "TLL TX":  TLL sentence of the cursor position is transmitted with the [ENT]key. Soft key 2: Not available Soft key 3: Not available Soft key 4: Not available "TLL TX" is color-inverted.
Chapter 2OPERATIONS2.8BASIC MENU OPERATIONS 2-752INSTRUCTION MANUAL 2.8 BASIC MENU OPERATIONS The settings which will not be frequently changed are called by the [MENU] key. This section describes the operation with the MENU key.  Keys for operation y [MENU] key yCursor keys y [MULTI] control y [CLEAR] key z [CLEAR] key Press the [CLEAR] key to return to the upper level.  MENU Key Operations (Example: Opening "IR") 1Press the [MENU] key. Select one of the menu items with ">" mark, then press the [ENT] key or the cursor key (right) to display the submenu.
Chapter 2OPERATIONS2.8BASIC MENU OPERATIONS 2-762Press the cursor key (down) or turn the [MULTI] control (clockwise) to select  RADAR Echo . 3Press the [ENT] key, the cursor key (right) or the [MULTI] control.   "RADAR Echo" menu appears. Current settings are displayed on the right pane of the menu. "RADAR Echo" is color-inverted.

Navigation menu