Jastec JTBT2100 Vehicle driving logs tracker User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1562589
Application ID	DL8TYuRS3NrIWHef8coYZw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	44.33kB (554066 bits)
Date Submitted	2011-10-19 00:00:00
Date Available	2012-04-16 00:00:00
Creation Date	2011-09-20 09:33:50
Producing Software	Acrobat Distiller 8.3.1 (Windows)
Document Lastmod	2011-10-17 19:13:59
Document Title	Users Manual
Document Creator	PScript5.dll Version 5.2
Document Author:	B9DAC3B6C8AB31

von-STD Manual Instruction
Cautions For Safety
We kindly recommend you to be fully aware of using a product accurately and for safety of user. All liabilities by
uncomplying cautions are not supposed to be responsible to manufacturer.
1 This product into water or prolonged exposure to moisture can cause failure resulting in no charge for broken A/S
1.
A/S.
2. Do not disassemble or repair this product if the label seal is broken or damaged, free A/S will not be received.
3. Do not separate or equip OBD II module while driving vehicle or ignition off. – This causes to car accident and defective of it.
4. Please note that on the surface of the product carefully to avoid strong detergent or chemicals.
5. This product works under the proper temperature -30~+80℃.
6. Do not impact the product. It’s the cause of product defective.
7. Using other products rated voltage is the cause of the crush. Rated voltage state must be sure to use the product.
8. After parking vehicle in a safe place, install OBD II module then drive.
9. When installing or removing product on the vehicle as the vehicle peripheral device could be due to injury, Please be careful.
10. Incorrect installation of the product by the vehicle’s shock and vibration and can cause data loss, after the installation, please check
it properly.
11. Products by shock or vibration of the vehicle is released from the car because it can cause data loss if the installation status checks
on a regular basis. This product is equipped with a breakdown of the car by the impact of accidents, damage, of driving record, we are
not responsible for missing.
12. Jastec Co.,Ltd provides cable, please use the original cable.
This confidential information is not supposed to disclosed and misused to the third party
1. von-STD Descriptions
1.1 Overview
Von-STD
STD as vehicle
hi l driving
di i
llogs ttracker
k designed
d i
d to
t collect
ll t a vehicle
hi l driving
di i
information
i f
ti
ffrom ECU(El
ECU(Electronic
i Control
C t l Unit)
U it)
By OBD standard protocol communication and can be saved a driving logs by connecting to PC.
This confidential information is not supposed to disclosed and misused to the third party
1. von-STD Descriptions
1.2 Specifications
In-vehicle Protocol
ISO 9141-2, ISO 14230-4(KWP-2000), ISO15765-4(CAN) J1850(PVM/VPW) protocol supported,
physical communication standard followed and high credibility being with vehicle DB.
32 bit main processor
Boasting fast and stable performance ARMv7 Cortex-M3 CPU has adopted.
Stability real-time operating system
System,hardware,applications,databases,data communications and other resources efficiently and
reliably manages the real-time operating system is used based on Tiny.
USB communication
USB Full-Speed (12Mbps) high data transmitter function supported.
Low power consumption and saving
Standby power consumption in driving conditions with low start-off when the vehicle’s powersaving features built in to prevent battery discharge.
Fi
Firmware
update
d t supportt
Firmware and vehicle DB p
program
to communicate with a PC via USB connection to upgrade
pg
is
easy and fast..
Mass storage space
Large amounts of information and operating data in real time on a high-capacity memory and
high data reliability by applying non-volatile memory can be saved.
Data communication
High-speed communications, the processor transfer, processing speed and large memory capacity
b combining
by
bi i
f t
features
such
h as vehicle
hi l driving
di i
record
d data
d t in
i reall time
ti
and
d to
t minimize
i i i the
th error.
Smart design
Due to small and light for easy installation and occupies less space, it doesn’t interfere with the
operation easier you can determine.
This confidential information is not supposed to disclosed and misused to the third party
1. von-STD Descriptions
1 3 Functions
1.3
Saving vehicle information.
Collecting and saving driving logs information.
Driving logs record
Vehicle identification information / module certification / module serial number information / driving
data starting time and ending time / ignition On and Off time /
Accumulated driving distance / module connection and disconnection time / driving information
transmitting time / acceleration pedal or throttle valve open angle
Module operating check and alarm
Display [indicator] : power display lamp[POWER –blue] / status display lamp[STATUS -red]
Driving information security
Encoded saving data to not modify a driving recorded information.
Di i
Driving
i f
information
ti
upload
l d
USB transmitter
itt preferred.
Power saving function
Automatically power will be off when ignition off.
Self diagnostic
Supporting
pp
g self diagnostic
function through
g OBD II module operating
g check ((Indicator).
Firmware upgrade support
Supporting firmware upgrade
This confidential information is not supposed to disclosed and misused to the third party
1. von-STD Descriptions
1.4 Specification
Specification
CPU
32 bit
bi ARMv7
ARM 7 Cortex-M3
M3
Memory
4 MB Internal Flash Memory
LED
Display LED
External interface specification
USB
USB 1.1(2.0
1 1(2 0 Compatible)
ibl )
VCP(Virtual COM Port) Supported
Bluetooth v2.0 Class 1
CAN[Control Area Network]: ISO 11898 /
Vehicle protocol
Bluetooth
2.4GHz ISM band
(JTBT1100)
Frequency
range: 2,400
2 400 ~ 2,483.5MHz
2 483 5MH
Data Rates: 1 Mbps
ISO 9141-2 / ISO 14230 [KWP 2000] /
SAE J1850 (PWM / VPW)
Connector type
SAE J1962 OBD-II 16Pin Standard Connector
Power
DC 12V / 24V vehicle, USB 5.0 V support
Power
consumption
2.4GHz ISM band
(JTBT2100)
Frequency
range: 2,400
2 400 ~ 2,483.5MHz
2 483 5MH
Data Rates: 1 Mbps
[stand-by] : ≤400mW
IEEE 802.11b/g
[saving mode] : ≤30mW
2.4GHz ISM band
Color: Black, Material: ABS
Size
[W]48mm X [D]28mm X [H]25mm
Weight
39 g
temperature
Bluetooth
Max power consumption: ≤500mW low
Case
Operating
Bluetooth v3.0 Class 2
WiFi
Frequency
range: 2,400
2 400 ~ 2,500MHz
2 500MH
(JTWF1100)
Data Rates: 1 ~ 54 Mbps
-30 ~ 80℃
This confidential information is not supposed to disclosed and misused to the third party
Typical TX power: 17dBm±2 @ 802.11b
16dBm±2 @ 802.11g
1. von-STD Descriptions
1.4 Composition
Name
Function
OBD II module (body)
Connection to vehicle OBD II connector.
USB cable
Use for uploading the driving logs data by PC connection.
Quick Start Manual
Quick guide manual
Program installation CD
von-S
von
S PC Manager installation program, included in user
user’ss manual.
This confidential information is not supposed to disclosed and misused to the third party
1. von-STD Descriptions
1.5 Body description
Front display LED
Red/Blue/White display LED
OBD connector
Connect to vehicle OBD diagnostic port with SAE J1962 OBD-II 16Pin standard connector.
Rear display LED
Operating LED
This confidential information is not supposed to disclosed and misused to the third party
2. Product Instructions
2 1 OBD II module installation
2.1
OBD II module installation is following below order.
1.
OBD II module installation requires after vehicle parking in safety area.
** Caution : A side brake or foot brake should be locked and shift also checked on the parking position.
2.
Please check vehicle engine should be off when if ignition on
3.
Check the position of vehicle OBD diagnostic connector.
This confidential information is not supposed to disclosed and misused to the third party
2. Product Instructions
2 1 OBD II module installation
2.1
OBD II module installation is following below order.
4. Connect vehicle OBD diagnostic connector and OBD II module connector.
5. Green LED of OBD II module will be blinked every 1 second.
6. Red or Green LED lamp will be continually blinked within 1 minute after ignition on.
7. After checking normal installation, green LED lamp blinks every 1 second after ignition off and All LED lamps will be turn off later [saving mode]
2.2 LED display status
STATUS
ECO driving!
g ((GOOD))
Normal driving! (NORMAL)
Bad driving! (BAD)
Wait for connection
Error
Blue LED
ON
ON
OFF
Blink
(1 second interval)
OFF
Sleep
OFF
** Caution : Please contact to customer service center when you have a problem.
10
This confidential information is not supposed to disclosed and misused to the third party
Red LED
OFF
ON
ON
OFF
Blink
(1 second interval)
OF
2. Product Instructions
2.3 OBD II module separation
** Caution : OBD II module separation should be performed at safety area after parking.
** Caution : The separation from vehicle is prohibited if not the purpose of driving data saving or transmitting.
** Caution
C ti
:P
Performing
OBD II module
d l separation
ti
on iignition
iti
on may b
be caused
d tto d
data
t lloss or module
d l d
damaged.
1.
2.
11
Turn vehicle ignition off.
Pull OBD II module from vehicle OBD diagnostic connector then separating it.
This confidential information is not supposed to disclosed and misused to the third party
2. Product Instructions
2 4 Driving log data saving and transmitting
2.4
1.
Preparation
1) PC manager program needs to install to save the driving logs data recorded from OBD II module.
* Tip : A program installation manual is available [3. PC Manager installation manual(31~34 page)]
2) Please separate OBD II module from vehicle. [2.6 module separation (21 page)]
** Caution : Vehicle data on the status of connecting to vehicle can not be transmitted by USB cable. Please separate
OBD II module from vehicle.
2. Connection
1) OBD II module should be connected to PC USB port by USB cable we provided.
2) USB mode display LED lamp will be blinked if connection is normal.
** Caution : Don’t separate USB cable while PC communicating OBD II module.
12
This confidential information is not supposed to disclosed and misused to the third party
3. Warranty & After Sale Service
3.1 Before A/S request service
**Caution : Driving logs data should be saved certainly in advance for A/S request if a product’s defect checked.
13
Power and LED status off
Check OBD II module and 16 pin connector connection status.
status
Not connected to PC
Check PC USB port and OBD II module connection status and PC USB
port status.
Not connecting OBD II module to Von-S PC
Manager program
Click “connection” icon to connect OBD II module after checking USB
connection status to PC.
PC
Not supporting Vista or Window7 to PC
See program installation tips for 3-2 Window Vista / window7 and page
34
This confidential information is not supposed to disclosed and misused to the third party
3. Warranty & After Sale Service
3.2 Warranty Service
1. Warranty Period : 1 year
2. Warranty Details
1) Any defective or damage within warranty period can be repaired free A/S service or exchanged as free of charge.
2 Any damage
2)
or defective
d f i b
by customer’s
’ misuse
iis not allowed
ll
d ffree exchange
or ffree charged
d A/S
S service.
3. Exchange and Return
1) An exchange or return is possible within 1 week after purchase if not opening box.
2) A shipping charge against retuning product because of just customer’s changed mind may be paid by customer.
4. Others
Oth
1) Warranty period is valid only for 12 months from manufacturing date if not checking a purchasing date.
2) Repair charge will be billed even though it’s warranty period as below.
- Defective by user’s misuse (impact/flooded/fault)
- Dismantle or alteration by user’s intention.
- Defective by natural disaster
disaster.
- Repaired not in official After Sales service centre.
3) Please contact to A/S call service centre for repair charges.
A/S call service : (031-719-5170 Extension : 206)
14
This confidential information is not supposed to disclosed and misused to the third party
FCC ID : UK4JTBT2100
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications (including the antennas) made to this device that are not expressly approved
by the manufacturer may void the user's authority to operate the equipment.
FCC RF Radiation Exposure Statement: This equipment complies with FCC RF Radiation exposure limits
set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating
in conjunction with any other antenna or transmitter.
This equipment should be installed and operated with a minimum distance of 20 centimeters between
the radiator and your body.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void the user's authority to operated the equipment
under FCC rules.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2011:09:20 09:33:50+09:00
Author                          : 
Modify Date                     : 2011:10:17 19:13:59+09:00
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 8.3.1 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Title                           : <4D6963726F736F667420506F776572506F696E74202D20766F6E2D5354445FB8DEB4BABEF35FB4DCB8BBB1E2C6C05F323031315F30355F3137BFB5B9AE205BC8A3C8AF20B8F0B5E55D>
Creator                         : 
Has XFA                         : No
Page Count                      : 15

EXIF Metadata provided by EXIF.tools