Jay Electronique SB RF module User Manual OEM Manual

Jay Electronique RF module OEM Manual

OEM Manual

T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016 Module integration manual Product Description The RF module with the FCCID number OQMSB is a compact high performance module for 25 kHz narrow band 2-FSK operation with embedded proprietary protocol. The modules are completely shielded and certified for operation under the US radio regulations for license-free use. Applications Remote controlled machines Cranes Features  Smallest in the world (50 x 39 x 0.7 mm)  25 kHz narrow band multi-channel operation  Very low current consumption  Addressing and Error check  No external components  Easy to use data interface  Wide supply voltage range, 2.8 – 5.5 V  Conforms with FCC CFR 47 part 15
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016 Quick Reference Data Parameter Jay RF Module Units Frequency band 911.8 – 918.2 MHz Number of channels 64 Channel bandwidth 25 kHz Data rate 4.8 kbits/s Max output power (typ.) -8 dBm Sensitivity -114 dBm Supply voltage 2.8 – 5.5 Volts Current consumption, RX 31 mA Current consumption, TX 37 mA * Programmable. Maximum allowed radiated power under FCC CFR 47, part 15 is -1 dBm ERP. Typical Application Circuit
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016 Pin Description Pin no Pin name Description 1 EN_PA PA enable input, active high 2 PWRF2 Not used 3 RTS_TXEN_RADIO Not used 4 CTS/RXTX/RXEN_RADIO UART Clear to Send 5 VAccu Supply voltage input 6 GND System ground 7 SPI_uc_SCK/ON_OFF SPI Clock 8 SPI_uc_MISO SPI MISO 9 SPI_uc_MOSI SPI MOSI 10 RESET_RADIO Reset 11 SEL_FILLE Not used 12 SPI_uc_NSS/CONFIG_RADIO SPI Chip Select 13 RSSI_RADIO Not used 14 DATA_RX UART RX Data 15 DATA_TX UART TX Data 16 GND System ground 17 RF RF I/O connection to antenna
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016 Block Diagram The module contains a communication controller with embedded proprietary protocol software, a narrow band high performance RF transceiver and three internal voltage regulators. The communication controller handles the radio packet protocol. Data to be sent by the host is received at the DATA_RX pin and buffered in the communication controller. The data packet is then assembled with preamble, synchronization word and data with CRC check sum before it is transmitted on RF. The asynchronous UART interface consists of DATA_TX, DATA_RX and CTS/RXTX/RXEN_RADIO signals and it is used for hardware handshake flow control. The RF transceiver modulates the data to be transmitted on RF frequency, and demodulates data that are received. Narrow band technology is used to enhance sensitivity and selectivity. The supply voltage is connected to the VAccu pin. The module contains three internal voltage regulators and can therefore operate over a wide supply voltage range.
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016 FCC The OEM integrators are responsible for ensuring that the end-user has no manual instructions to remove or install module. The module is limited to OEM installation ONLY This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. These following instructions/statements shall be reported on the User Manual: Any changes or modifications to this equipment not expressly approved by JAY electronique may cause, harmful interference and void the FCC authorization to operate this equipment This equipment complies with FCC’s radiation exposure limits set forth for an uncontrolled environment under the following conditions: 1. This equipment should be installed and operated such that a minimum separation distance of 20cm is maintained between the radiator (antenna) and user’s/nearby person’s body at all times. 2. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The RF module has been certified for mobile and fixed applications. If the module will be used for portable application the device must undergo SAR testing and the following instructions shall be reported on the User Manual. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations. If SAR measurement is not required: This portable equipment with it’s antenna complies with FCC’s radiation exposure limits set forth for an uncontrolled environment. To maintain compliance, follow the instructions below : 1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. Avoid direct contact to the antenna, or keep contact to a minimum while using this equipment. If SAR measurement is required: This portable equipment with it’s antenna complies with FCC’s radiation exposure limits set forth for an uncontrolled environment. This equipment has shown compliance with FCC’s Specific Absorption Rate (SAR) limits. To maintain compliance, follow the instructions below : 1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016 Authorized antennas:
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016 Antenna FR05-S1-R-0-105
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016 VUA10xBM
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016 FLX900/915-FME
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016 VUB884
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016 EBDS-PRO900-4-BNC
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016 VUA001B
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016 Antenna installation requirements: The external antenna must be installed at a distance from the class 3 cables and power components (power supply, motor, variable speed drives …) while remaining in an area which is favourable to radio reception. It must be located at a certain height. No metal object which could form a screen should be located in front of the external antenna (risk of communication cut-out).
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016 Moreover, the host equipment must be labelled as follows: Contains Transmitter Module FCC ID : OQMSB or Contains FCC ID : OQMSB “This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.” (When the device is so small or for such use that it is not practicable to place the statement specified above on it, the information required shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed.) User Manual shall include the following instructions/statements: For class A Equipment This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. For class B Equipment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help Warning: This modular is used exclusively by Jay Electronique.
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016 IC The OEM integrators are responsible for ensuring that the end-user has no manual instructions to remove or install module. These following instructions/statements shall be reported on the User Manual: This equipment complies with RSS102’s radiation exposure limits set forth for an uncontrolled environment under the following conditions: 1. This equipment should be installed and operated such that a minimum separation distance of 20cm is maintained between the radiator (antenna) and user’s/nearby person’s body at all times. 2. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet équipement est conforme aux limites d’expositions de la CNR102 applicables pour un environnement non contrôlé aux conditions suivantes: 1. Cet équipement devra être installé et fonctionner de telle manière qu’une distance minimale de séparation de 20 cm soit maintenue entre la partie rayonnante (l’antenne) et l’utilisateur / les personnes à proximité à tout moment. 2 Cet émetteur ne doit pas être co-localisé ou opérer en conjonction avec toute autre antenne ou émetteur. The RF module has been certified for mobile and fixed applications. If the module will be used for portable application the device must undergo SAR testing and the following instructions shall be reported on the User Manual: Le module RF a été certifié pour les applications mobiles et fixes. Si le module est utilisé pour une application portable, l'appareil doit subir un test DAS et les instructions suivantes doivent être consignées dans le manuel de l'utilisateur: If SAR measurement is not required: This portable equipment with it’s antenna complies with RSS102’s radiation exposure limits set forth for an uncontrolled environment. To maintain compliance, follow the instructions below : 1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. Avoid direct contact to the antenna, or keep contact to a minimum while using this equipment.
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016 Si la mesure de DAS n’est pas requise: Cet équipement portable avec ses antennes est conforme aux limites d’expositions de la CNR102 applicables pour un environnement non contrôlé. Pour maintenir la conformité suivez les instructions ci-dessous: 1 Cet émetteur ne doit pas être co-localisé ou opérer en conjonction avec toute autre antenne ou émetteur. 2 Évitez tout contact direct avec l'antenne ou gardez le contact au minimum pendant l'utilisation de cet équipement. If SAR measurement is required: This portable equipment with it’s antenna complies with RSS102’s radiation exposure limits set forth for an uncontrolled environment. This equipment has shown compliance with RSS102’s Specific Absorption Rate (SAR) limits. To maintain compliance, follow the instructions below : 1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Si la mesure de DAS est requise: Cet équipement portable avec ses antennes est conforme aux limites d’expositions de la CNR102 applicables pour un environnement non contrôlé. Cet équipement a démontré la conformité aux limites de Débit d’Absorption Spécifique (DAS). Pour maintenir la conformité suivez les instructions ci-dessous: 1 Cet émetteur ne doit pas être co-localisé ou opérer en conjonction avec toute autre antenne ou émetteur.
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016 This radio transmitter (IC: 3393A-SB) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio (IC : 3393A-SB) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. Authorized antennas / Antennes autorisées : The characteristic of antennas are listed in previous paragraphs. Les caractéristiques des antennes sont décrites dans les paragraphes précédents.
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016 Antenna installation requirements / Exigences d’installation des antennes : The external antenna must be installed at a distance from the class 3 cables and power components (power supply, motor, variable speed drives …) while remaining in an area which is favourable to radio reception. It must be located at a certain height. No metal object which could form a screen should be located in front of the external antenna (risk of communication cut-out). L’antenne devra être éloignée des câbles de classe 3 et éléments de puissance (alimentation, moteur, variateurs...) tout en restant dans une zone favorable à la réception et à l’émission radio. Le Transceiver doit être idéalement situé en hauteur, au-dessus de l’opérateur manipulant le module opérateur, l’antenne dirigée vers le bas. Il ne devra y avoir entre l’opérateur et l’antenne aucune masse métallique pouvant faire écran (risque de coupures de communication).
T940-HOM-004-Module integration manual_Rev4.docx Date: November 21, 2016 This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: 1. This device may not cause harmful interference; and 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1. L’appareil ne doit pas produire de brouillage ; 2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Moreover, the host equipment must be labelled as follows: Contains Transmitter Module IC : 3393A-SB or Contains IC : 3393A-SB

Navigation menu