Jiangmen Dascom Computer Peripherals TD12250 Dot Matrix Printer User Manual
Jiangmen Dascom Computer Peripherals Co.,Ltd. Dot Matrix Printer Users Manual
UserManual.wiki
>
Jiangmen Dascom Computer Peripherals
>
TD12250 User Manual
Users Manual
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![Tally Dascom 1225 15Panel Operation There are 3 states of operation: Online, Offline and Power On. In the Online state, the keys provide the following functions: Go to Tear Off position, Line Feed/Form feed, Load/Eject, and switch to Offline state. In the Offine state, the keys provide the following functions: Font select, Pitch select, Line Feed/Form feed, Load/Eject, and switch to Online state, micro feed, control PE (paper error) sensitivity, clear buffer and restore factory defaults. To enter the Power On state, the user holds down a key or a combination of keys while powering up the printer. This state provides the following functions: Main Menu setup, Hex-dump, print Main Menu, access Service Menu, adjust page margins, restore factory defaults, and firmware update. The followings describe the 3 states in details. Legend: [A] = press and hold switch A {B} = press and then release switch B [A]+ {B} = press switch B while holding A](https://usermanual.wiki/Jiangmen-Dascom-Computer-Peripherals/TD12250/User-Guide-2214100-Page-29.png)
![Tally Dascom 1225 16Online State Function Name Switch Operation LED Function Description Online {S5} L10 Toggles between Online and Offline states Load/Eject {S4} - x Load: Automatically loads the paper (according to path selection) when no paper is on the platen. x Eject: For rear tractor, it retracts the form from the platen to allow users to install cut sheets. (NOTE: Users have to toggle the path selection lever.) For cut sheets, it ejects the form on the platen. LF {S3} - Feeds a line with every press of S3. FF [S3] - By holding S3, the printer initially feeds a few lines; then feeds the form to the next TOF for rear tractor or ejects the form for cut sheets. Tear Off {S2} L5 flashingThis is valid for tractor mode only. It feeds the form to the tear-off position. After tearing off the form, printing starts on the next TOF by: x pressing S2 once, or x receiving print data from the host.](https://usermanual.wiki/Jiangmen-Dascom-Computer-Peripherals/TD12250/User-Guide-2214100-Page-30.png)
![Tally Dascom 1225 17Offline State Function Name Switch Operation LED Function Description Font {S1} L1~L4 Selects the font. Pitch {S2} L5~L8 Selects the pitch. LF {S3} - Feeds a line with every press of S3. FF [S3] - By holding S3, the printer initially feeds a few lines; then feeds the form to the next TOF for rear tractor or ejects the form for cut sheets. Load/Eject {S4} - x Load: Automatically loads the paper (according to path selection) when no paper is on the platen. x Eject: For rear tractor, it retracts the form from the platen to allow users to install cut sheets. (NOTE: Users have to toggle the path selection lever.) For cut sheets, it ejects the form on the platen. Online {S5} L10 Toggles between Online and Offline states Micro Forward {S4}+[S5] - While holding down S5, press S4 to micro feed paper up. Micro Reverse {S3}+[S5] - While holding down S5, press S3 to micro feed paper down. Activate user-defined sensitivity[S2]+{S3} Activates the calibrated PE sensor sensitivity value according to the currently selected paper path. Beeps once when completed.](https://usermanual.wiki/Jiangmen-Dascom-Computer-Peripherals/TD12250/User-Guide-2214100-Page-31.png)
![Tally Dascom 1225 18Calibrate PE sensor sensitivity{S1}+[S2] - x Out-of-paper: Beeps once. Automatically loads a form in 10 seconds. x Paper loaded: Calibrates PE sensor with paper loaded and save the sensitivity value. Beeps 5 times when completed. x [NOTE: There are 2 independent sensors for rear tractor and front friction. Restore default PE sensor sensitivity[S2]+{S4} Resets PE sensor sensitivity to factory defaults. Beeps twice when completed. Clear Buffer and Reset {S1}+[S5] - x Clears the print buffer. Beeps once upon completion. x Pressing S1 longer initializes the printer to default settings. Beeps 3 times upon completion.](https://usermanual.wiki/Jiangmen-Dascom-Computer-Peripherals/TD12250/User-Guide-2214100-Page-32.png)
![Tally Dascom 1225 19Power-On State FunctionName Switch Operation LED Function Description Menu Setup / EDS[S2] - Allows for Main Menu setting changes. Please read the instructions printed on how to change settings when this mode is activated. (EDS: Electronic DIP Switch) Hex Dump [S4] - Beeps once to indicate going into hex dump mode: x Prints data from host in hexadecimal representation. x Pressing S4 suspends the printing. x When the hex dump has finished, pressing S4 forces the printing of the last line of data, as any line termination control code from host has no function. x Pressing S1 can change the font. x Switch off the power to terminate the hex dump. Self Test / Status Page [S5] - Prints the printer settings and self-test pattern. Pressing S1 can change the font. Service Menu [S2]+[S3] - Vertical Alignment, Change Pin Function and Endless Self TestAdjust Page Margins [S4]+[S5] - Includes Adjust Fanfold Top Margin, Adjust Single Top Margin, Adjust Fanfold Left Margin, Adjust Single Left Margin and Adjust Tear-Off position.](https://usermanual.wiki/Jiangmen-Dascom-Computer-Peripherals/TD12250/User-Guide-2214100-Page-33.png)
![Tally Dascom 1225 20Restore Factory Defaults [S3]+[S4]+[S5] - Restore settings to factory defaults except for Change Pin, Vertical Alignment and Adjust Page Margin Parameters. FirmwareUpdate [S2]+[S3]+[S4]+ [S5]-x Alternate flashing of L9 and L10 indicates ready for firmware update from host. x When new firmware is being received: L1 and L2 will flash, followed by L1 and L3 flashing, then followed by L1 and L4 flashing. x When downloading is completed, the carriage returns to home position. Printer initializes normally. Language Setup [S3]+[S4] x Allows user to select one of the following languages: English, German, Russian, Italian, French, Spanish and Turkish. Factory default is English. Refer to Language Setup section below for details. Language Setup The panel menu can display the following languages: English, German, Russian, Italian, French, Spanish and Turkish. Factory default setting is English. To change it to another language, hold down the [LF/FF] and[Load/Eject] keys on the panel and power-on. Upon exiting the Language Setup Menu, a listing of the current configuration is printed, and this is followed by Main Menu Setup. Below is an example of changing from English to German language:](https://usermanual.wiki/Jiangmen-Dascom-Computer-Peripherals/TD12250/User-Guide-2214100-Page-34.png)
![Tally Dascom 1225 2330. Roman8 31. Coax/Twinax 32. New-437 33. New-Dig 850 34. Old-Code 860 35. Flarro 863 36. 865 Hebrew 37. CP 1257 38. 866 Ukraine 39. 866 Kazakhstan 40. Kamenicky 41. Mazovia 42. CP 775 43. CRO-ASCII 44. Arabic Farsi 45. Arabic Urdu 46. Greek DEC 47. Greek ELOT 928 Character Table Graphic Table, Italic Table Character table type selection Page Setup Page Setup Valid Settings Function Print Width 13.6", 8" Printable width options Line Per Inch 1, 2, 3, 4, 5, 6, 7, 8 Sets the line spacing Fanfold Form Length 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17" Sets the page length for tractor mode Fanfold Top Margin 0/60" … 10/60"…99/60" Sets the top margin for tractor mode. Due to mechanical tolerance, 0/60” is not guaranteed. Fanfold Bottom Margin 0/60"…10/60"...30/60" Sets the bottom margin for tractor mode. Due to mechanical tolerance, 0/60” is not guaranteed. Single Form Length 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.5", 11", 70/6", 12", 14", 17"Sets the page length for friction mode Single Top Margin 0/60" … 10/60"…99/60" Sets the top margin for friction mode. Due to mechanical tolerance, 0/60” is not guaranteed. Single Bottom Margin 0/60"…10/60"...30/60" Sets the bottom margin for friction mode. Due to mechanical tolerance, 0/60” is not guaranteed. Roll Paper Yes, No In friction mode, [LF/FF] will not eject the paper and feed to next page. (Assume roll paper) Perforation Skip Yes, No Skips printing on perforation area](https://usermanual.wiki/Jiangmen-Dascom-Computer-Peripherals/TD12250/User-Guide-2214100-Page-37.png)
![Tally Dascom 1225 86ESC C NUL n Set page length in inches ESC D Select Tab horizontally ESC E Select bold ESC F Cancel bold ESC G Select double-strike mode ESC H Cancel double-strike mode ESC I n Select printing mode ESC J n Perform n/180Ǝor n/216Ǝsingle line feed ESC K n1 n2 V1 V2 …Vn Normal density graphics ESC L n1 n2 V1 V2 …Vn Dual-Density Bit Image Graphics (Half Speed) ESC N n Select bottom margin ESC O Cancel bottom margin ESC P n Set proportional intercharacter ESC Q n Offline ESC R Clear tab ESC S n Select superscript/subscript ESC T Cancel superscript/subscript ESC U n Select bidirectional printing on/off ESC W n Select double-wide printing mode(continuous) ESC X n m Set left and right margin ESC Y n1 n2 V1 V2 …Vn Select double -density graphics ESC Z n1 n2 V1 V2 …Vn Select fourfold -density graphics ESC [- n1 n2 m1 m2 Select line ESC [@ n1 n2 m1 m2 m3 m4 Select printing mode ESC [I n1 n2 Hf Ls Hs Lf Sm NUL Hc Lc Select font and pitch ESC [ K n1 n2 init id para1 para2 …paran Set initialization condition ESC [ T n1 n2 n3 n4 Hc Lc Set code page ESC [\ Set vertical unit ESC [d Select printing quality ESC [f n1 n2 k m s v1 v2c Set barcode parameters ESC [g n1 n2 m Select high-density graphics printing ESC [p n1 n2 Set barcode data ESC ] Feed paper in reverse direction ESC_ n Print upper-line ESC- n Print underline ESC d n m Move the current printing position ESC j Stop printing ESC r n Select printing colour ESC * m Select graphic mode If you need more details regarding the emulation commands, please contact us.](https://usermanual.wiki/Jiangmen-Dascom-Computer-Peripherals/TD12250/User-Guide-2214100-Page-100.png)
