Jiangmen Dascom Computer Peripherals TD26000 Dot Matrix Printer User Manual 2610 UG LED LCD 12 12 04 00
Jiangmen Dascom Computer Peripherals Co.,Ltd. Dot Matrix Printer 2610 UG LED LCD 12 12 04 00
Contents
- 1. users manual
- 2. user manual
users manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1945130 |
| Application ID | UOQVaSTL37inQM+qnS9OBg== |
| Document Description | users manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 199.1kB (2488802 bits) |
| Date Submitted | 2013-04-19 00:00:00 |
| Date Available | 2013-04-19 00:00:00 |
| Creation Date | 2012-12-13 14:52:41 |
| Producing Software | Acrobat Distiller 7.0 (Windows) |
| Document Lastmod | 2012-12-13 14:52:41 |
| Document Title | Microsoft Word - 2610_UG_LED&LCD__12_12_04_00.doc |
| Document Author: | hp |
Tally Dascom 2610
Important Safety Instructions (English)
Read the following instructions thoroughly before starting up your printer.
Never carry out maintenance or repair work yourself. Always contact a qualified service technician.
Keep this Operator’s Manual in a place which is easily accessible at all times.
Place the printer on a solid and even base so that it cannot fall.
Never place the printer in the vicinity of inflammable gas or explosive substances.
Ensure the printer is connected to a socket with the correct mains voltage.
Always disconnect the printer from the mains before opening the device to perform maintenance work
or remedy errors.
Do not expose the printer to high temperatures, direct sunlight or dust.
Keep all liquids away from the printer.
Protect the printer from shock, impact and vibration.
Make sure that the printer and computer are switched off before connecting the data cable.
The print head will become very hot during printing; avoid contact with the print head after printing has
finished.
Do not perform any operation or action in any way other than those provided in this manual. When in
doubt, contact your dealer or your customer support.
Tally Dascom 2610
Wichtige Sicherheitshinweise (German)
Lesen Sie bitte diese Sicherheitshinweise durch, bevor sie den Drucker in Betrieb nehmen.
Führen Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verständigen Sie immer
einen qualifizierten Servicetechniker.
Bewahren Sie diese Dokumentation an einem jederzeit zugänglichen Ort auf.
Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen kann.
Stellen Sie den Drucker keinesfalls in der Nähe von leicht entzündlichen Gasen oder explosiven Stoffen
auf.
Den Drucker nur an eine Steckdose mit der richtigen Spannung anschließen.
Wenn Sie den Drucker vom Netz trennen wollen, den Drucker ausschalten und immer den Netzstecker
an der Steckdose ziehen.
Den Drucker weder hohen Temperaturen noch direktem Sonnenlicht und Staub aussetzen.
Keine Flüssigkeiten mit dem Drucker in Berührung bringen.
Den Drucker keinen Erschütterungen, Stößen oder Vibrationen aussetzen.
Sicherstellen, dass der Drucker und der Computer ausgeschaltet sind, bevor das Datenkabel
angeschlossen wird.
Der Druckkopf wird während des Druckens heiß. Vor dem Berühren deshalb einige Zeit abkühlen lassen.
Weichen Sie bei der Bedienung des Druckers nicht von den Anweisungen in der Dokumentation ab.
Bei Unklarheiten wenden Sie sich bitte an Ihren Händler oder Ihren Kundendienst.
Maschinenlärm informations – Verordnung – 3.GPSGV, der höchste Schalldruckpegel beträgt 70 dB(A)
oder weniger gemäß EN ISO 7779.
II
Tally Dascom 2610
Consignes importantes de sécurité (French)
Lire attentivement les instructions suivantes avant de mettre l’imprimante en service.
Ne jamais effectuer soi-même les travaux d’entretien et de réparations. Contacter toujours un dépanneur
qualifié.
Placer l’imprimante sur un support stable de façon à ce qu’elle ne puisse pas tomber.
Ne jamais placer l’imprimante à proximité de sources de gaz aisément inflammables ou de substances
explosives.
Ne connecter l’imprimante à une prise que lorsque la tension est correcte.
Pour déconnecter l’imprimante de l’alimentation principale, mettre l’imprimante hors tension et toujours
débrancher le connecteur secteur de la prise murale.
Ne pas exposer l’imprimante à des températures élevées, à la lumière directe du soleil ou à la poussière.
Ne pas mettre l’imprimante en contact avec des liquides.
Ne pas exposer l’imprimante à des chocs, impacts ou vibrations.
S’assurer que l’imprimante et l’ordinateur sont hors tension avant de connecter le câble de données.
La tête d’impression est brûlante pendant l’impression. C’est pourquoi laissez-la refroidir quelques
instants avant d’y toucher.
N'exécutez aucune opération ni action d'une autre manière que celle indiquée dans ce manuel. En cas
de doute, veuillez contacter votre distributeur ou service après-vente.
III
Tally Dascom 2610
Indicazioni di sicurezza importanti (Italian)
Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni.
Non eseguire mai da sé gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un tecnico di
assistenza qualificato.
Conservare le presenti istruzioni per l’uso in un luogo sempre accessibile.
Collocare la stampante su una superficie stabile, per evitare che cada a terra.
Non collocare la stampante in prossimità di gas facilmente infiammabili o di sostanze esplosive.
Collegare la stampante a una presa di corrente con tensione adeguata.
Per scollegare la stampante dalla rete di alimentazione, spegnere la stampante e disinserire sempre il
connettore di rete dalla presa.
Non esporre la stampante ad elevate temperature né alla luce solare diretta e alla polvere.
Evitare il contatto della stampante con liquidi.
Non esporre la stampante a colpi, scosse o vibrazioni.
Verificare che la stampante e il computer siano spenti prima di collegare il cavo di trasmissione dati.
Durante la stampa, la testina si surriscal-da notevolmente. Prima di toccarla, se necessario opportuno
quindi lasciarla raffreddare qualche istante.
Non eseguire alcuna operazione o azione se non nella maniera descritta nel presente manuale. In caso
di dubbio, contattare il rivenditore o dalla società incaricata dell’assistenza.
IV
Tally Dascom 2610
Instrucciones de seguridad importantes (Spanish)
Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio.
Nunca lleve a cabo trabajos de mantenimiento o reparación Ud. mismo, sino consulte a un técnico de servicio
calificado.
Guarde las presentes instrucciones de servicio en un lugar de fácil acceso en cualquier momento.
Ponga la impresora sobre un base estable de manera que no pueda caer al suelo.
Nunca coloque la impresora en la vecindad de gases de fácil inflamabilidad o sunstancias explosivas.
Asegure conectar la impresora sólo a un enchufe con un voltaje correcto.
Cuando quiera desconectar la impresora de la red, apague la impresora y siempre tire la clavija de
alimentación del enchufe.
No exponga la impresora a temperaturas altas, a la luz solar directa y al polvo.
No ponga la impresora en contacto con fluidos.
Nunca exponga la impresora a sacudidas, choques o vibraciones.
Asegúrese de que la impresora y el ordenador estén apagdos antes de conectar el cable de datos.
La cabeza de impresión se pone muy caliente durante la impresión. Por lo tanto, deje enfriarlo algún
tiempo antes de tocarla.
No permita que se realice cualquier operación o acción de una forma diferente a lo que se señala en el
manual. En caso de duda, póngase en contacto con su comerciante o con su servicio post-venta.
Tally Dascom 2610
ɉɪɚɜɢɥɚ ɩɨ ɬɟɯɧɢɤɟ ɛɟɡɨɩɚɫɧɨɫɬɢ. (Russian)
ɉɪɨɱɢɬɚɣɬɟ, ɩɨɠɚɥɭɣɫɬɚ, ɢɧɫɬɪɭɤɰɢɸ ɩɨ ɬɟɯɧɢɤɟ ɛɟɡɨɩɚɫɧɨɫɬɢ ɩɟɪɟɞ ɜɤɥɸɱɟɧɢɟɦ ɜ ɪɚɛɨɬɭ ɩɪɢɧɬɟɪɚ.
ɇɟ ɜɵɩɨɥɧɹɣɬɟ ɬɟɯɧɢɱɟɫɤɢɟ ɪɚɛɨɬɵ ɢ ɪɟɦɨɧɬ ɬɟɯɧɢɤɢ ɫɚɦɨɫɬɨɹɬɟɥɶɧɨ, ɧɨ ɫɨɨɛɳɚɣɬɟ ɨ
ɧɟɢɫɩɪɚɜɧɨɫɬɹɯ ɤɜɚɥɢɮɢɰɢɪɨɜɚɧɧɵɦ ɫɟɪɜɢɫɧɵɦ ɬɟɯɧɢɤɚɦ.
Ⱦɚɧɧɚɹ ɢɧɫɬɪɭɤɰɢɹ ɞɨɥɠɧɚ ɛɵɬɶ ɜɫɟɝɞɚ ɞɨɫɬɭɩɧɚ ɤɚɠɞɨɦɭ ɩɨɥɶɡɨɜɚɬɟɥɸ.
ɍɫɬɚɧɨɜɢɬɟ ɩɪɢɧɬɟɪ ɧɚ ɪɨɜɧɨɦ ɢ ɫɬɚɛɢɥɶɧɨɦ ɦɟɫɬɟ ɬɚɤ, ɱɬɨɛɵ ɨɧ ɧɟ ɫɦɨɝ ɭɩɚɫɬɶ ɧɚ ɩɨɥ.
ɇɢ ɜ ɤɨɟɦ ɫɥɭɱɚɟ ɧɟ ɫɬɚɜɶɬɟ ɩɪɢɧɬɟɪ ɜɛɥɢɡɢ ɥɟɝɤɨ ɜɨɫɩɥɚɦɟɧɹɸɳɢɯɫɹ ɝɚɡɨɜ ɢ ɜɡɪɵɜɱɚɬɵɯ
ɜɟɳɟɫɬɜ.
ȼɤɥɸɱɚɣɬɟ ɩɪɢɧɬɟɪ ɜ ɪɨɡɟɬɤɭ ɬɨɥɶɤɨ ɫ ɫɨɨɬɜɟɬɫɬɜɭɸɳɢɦ ɧɚɩɪɹɠɟɧɢɟɦ.
ȿɫɥɢ ȼɵ ɯɨɬɢɬɟ ɨɬɤɥɸɱɢɬɶ ɩɪɢɧɬɟɪ ɨɬ ɧɚɩɪɹɠɟɧɢɹ, ɫɧɚɱɚɥɚ ɜɵɤɥɸɱɢɬɟ ɩɪɢɧɬɟɪ ɫɚɦ ɢ ɡɚɬɟɦ
ɜɵɧɶɬɟ ɲɬɟɤɟɪ ɢɡ ɪɨɡɟɬɤɢ.
Ȼɟɪɟɝɢɬɟ ɩɪɢɧɬɟɪ ɨɬ ɧɚɝɪɟɜɚɧɢɹ, ɨɬ ɩɨɩɚɞɚɧɢɹ ɧɚ ɧɟɝɨ ɩɪɹɦɵɯ ɫɨɥɧɟɱɧɵɯ ɥɭɱɟɣ ɢ ɩɵɥɢ.
ɇɟ ɞɨɩɭɫɤɚɣɬɟ ɩɨɩɚɞɚɧɢɹ ɠɢɞɤɨɫɬɢ ɧɚ ɩɪɢɧɬɟɪ.
ɇɟɥɶɡɹ ɩɨɞɜɟɪɝɚɬɶ ɩɪɢɧɬɟɪ ɬɪɹɫɤɟ, ɭɞɚɪɚɦ ɢ ɜɢɛɪɚɰɢɢ.
ɍɛɟɞɢɬɟɫɶ, ɱɬɨ ɩɪɢɧɬɟɪ ɢ ɤɨɦɩɶɸɬɟɪ ɜɵɤɥɸɱɟɧɵ, ɬɨɥɶɤɨ ɩɨɫɥɟ ɷɬɨɝɨ ɫɨɟɞɢɧɢɬɟ ɩɪɢɧɬɟɪ ɫ
ɤɨɦɩɶɸɬɟɪɨɦ.
ɉɟɱɚɬɚɸɳɚɹ ɝɨɥɨɜɤɚ ɧɚɝɪɟɜɚɟɬɫɹ ɜɨ ɜɪɟɦɹ ɪɚɛɨɬɵ ɩɪɢɧɬɟɪɚ. ɉɨɷɬɨɦɭ ɩɨɞɨɠɞɢɬɟ ɤɚɤɨɟ-ɬɨ ɜɪɟɦɹ,
ɩɪɟɠɞɟ ɱɟɦ ɞɨɬɪɨɧɭɬɶɫɹ ɞɨ ɧɟɟ.
ɉɨɥɶɡɭɣɬɟɫɶ ɩɪɢɧɬɟɪɨɦ ɬɚɤ, ɤɚɤ ɷɬɨ ɧɚɩɢɫɚɧɨ ɜ ɞɨɤɭɦɟɧɬɚɰɢɢ. ȿɫɥɢ ɭ ȼɚɫ ɜɨɡɧɢɤɚɸɬ ɧɟɹɫɧɨɫɬɢ,
ɨɛɪɚɳɚɣɬɟɫɶ ɫ ɜɨɩɪɨɫɚɦɢ ɤ ȼɚɲɢɦ ɩɪɨɞɚɜɰɚɦ ɢɥɢ ɜ ɫɟɪɜɢɫɧɵɣ ɰɟɧɬɪ.
VI
Tally Dascom 2610
Instruções Importantes sobre Segurança (Portuguese)
Leia as instruções de segurança antes de usar a impressora.
Consulte sempre um técnico qualificado para executar uma reparação .
Coloque a impressora sobre uma base sólida e nivelada, para que ela não sofra quedas.
Jamais instale a impressora nas proximidades de lugares onde haja gás inflamável ou substâncias
explosivas.
Assegure-se de conectar a impressora à tomada elétrica com a voltagem apro-priada.
Quando desligar a impressora da rede, desligue sempre a impressora e retire o cabo da tomada.
Não exponha a impressora a temperaturas altas ou luz solar direta.
Não aproxime substâncias líquidas da impressora.
Proteja a impressora de choques, impactos e vibrações.
Desligue a impressora e o computador antes de conectar o cabo da rede.
A cabeça da impressora pode ficar muito quente . Portanto, espere algum tempo antes de tocá-la.
Não faça nenhuma operação ou ação além das recomendadas neste manual. Em caso de dúvida,
contate seu revendedor ou companhia de serviço.
VII
Tally Dascom 2610
ÖnemliGüvenlik Talimatları (Turkish)
Lütfen, yazıcıyı iúletime geçirmeden önce bu güvenlik talimatlarını bütünüyle dikkatle okuyun.
Bakım ve tamir çalıúmalarını kesinlikle ve hiçbir surette kendi baúınıza yapmayın; her zaman kalifiyebir uzman
servis-teknisyenine haber verin.
Yazıcıyı, üzerinden yere düúmesimümkün olmayacak sabit ve düz bir zemine yerleútirin.
Yazıcıyı kesinlikle ve hiçbir surette kolayca yanabilecek gaz veya patlayıcı maddeler içeren nesnelerin
yakınına koymayın.
Yazıcı akım kablosunu sadece do÷ru gerilime sahip bir prize takın.
Yazıcıyı úebeke a÷ından ayırmak istedi÷inizde, yazıcıyı kapatın ve a÷-fiúini her zaman prizden çıkartın.
Yazıcıyı ne yüksek ısılı ne de do÷rudan güneú ıúı÷ına ve toza mâruz kalan mekânlarda bulundurun.
Yazıcıhiçbir sıvı maddeyle temasta olmamalıdır.
Yazıcı hiçbir sarsıntıya, darbeye veya titreúime mâruz kalmamalıdır.
Veri kablosu ba÷lanmadan önce hem yazıcının hem de bilgisayarın kapalıolduklarından emin
olmalısınız.
Yazıcının baúı basma esnasında yüksek ısıya ulaúıyor. Bu yüzden lütfen dokunmadan önce kısa süre
so÷umasını bekleyin.
Yazıcının iúletimi ve kullanımında bu dokümantasyondaki talimatların hiç dıúına çıkmayın. Sorunlu
görünen hususlarda lütfen imâlatçınıza veya müúteri hizmetleri servisinize baúvurun.
VIII
Tally Dascom 2610
TRADEMARK ACKNOWLEDGEMENTS
“IBM” is a trademark of International Business Machines Corporation.
“EPSON” is a trademark of Epson America Incorporated.
“DEC” is a trademark of Digital Equipment Corporation.
“Centronics” is a trademark of Centronics Data Computer Corporation.
“DOS” is a trademark of Microsoft Corporation.
“SAP” is a trademark of SAP AG.
“Windows”, “Windows 7”,”Windows 8”, “Windows 95”, “Windows 98“, “Windows NT”, “Windows 2000”, “Windows
2003/2008/2013 Server”, “Windows XP” and “Windows Vista” are trademarks of Microsoft Corporation.
All other product names and company names appearing in this manual are the registered trademarks or
trademarks of the individual companies.
IX
Tally Dascom 2610
TABLE OF CONTENTS
Printer at a glance ............................................................................................................................... 1
1.1
Unpacking the printer ...................................................................................................................1
1.2
Unpacking the Printer ...................................................................................................................2
1.3
Parts description...........................................................................................................................4
Installation ........................................................................................................................................... 5
2.1
Placing the printer.........................................................................................................................5
2.2
Connecting the printer ..................................................................................................................5
2.2.1
Parallel interface (IEEE 1284) ...................................................................................................... 6
2.2.2
USB 2.0 (Full Speed) ..................................................................................................................... 6
2.2.3
Ethernet ........................................................................................................................................... 6
2.2.4
Serial Interface (RS-232C) as option .......................................................................................... 7
2.2.5
Connecting the power.................................................................................................................... 7
2.2.6
Switch on the printer ...................................................................................................................... 7
2.3
Installing the ribbon cartridge ...................................................................................................... 8
Installing the paper .............................................................................................................................10
3.1
Adjusting the print gap for various form thicknesses ..................................................................10
3.2
Paper path introduction .............................................................................................................. 11
3.2.1
Cut sheet paper handling (front friction only) ........................................................................... 11
3.2.2
Fanfold paper handling................................................................................................................ 12
3.2.3
Top-Of-Form adjustment ............................................................................................................. 16
Control Panel Operation..........................................................................................................................17
4.1 Operation of the LED Panel............................................................................................................. 17
4.1.1 Keys and Indicators.......................................................................................................................... 17
4.1.2
Online Operations ........................................................................................................................ 19
4.1.3
Offline Operations ........................................................................................................................ 20
4.1.4
Power-On Operations .................................................................................................................. 22
4.2 Operation of the LCD Panel............................................................................................................. 23
4.2.1
The LC display .............................................................................................................................. 23
4.2.2
Online mode .................................................................................................................................. 24
4.2.3
Offline mode .................................................................................................................................. 24
4.2.4
Setup mode ................................................................................................................................... 25
4.2.5
Power on functions....................................................................................................................... 25
Setting parameters for the printer .............................................................................................................26
5.1
Setting the parameters through the LED Panel ..........................................................................26
5.1.1
Fine tuning the TOF and Tear positions .................................................................................... 26
5.1.2
Select a font .................................................................................................................................. 27
5.1.3
Settings within Menu.................................................................................................................... 28
5.2
Setting the parameters through the LCD Panel ..........................................................................29
5.2.1
Enabling access to menu mode ................................................................................................. 29
5.2.3
Menu configurations..................................................................................................................... 30
5.2.4
Menu handling .............................................................................................................................. 32
5.2.5
Selecting the LC display language ............................................................................................ 33
5.3
Menu structure ........................................................................................................................... 34
5.4
Full list parameters setting.......................................................................................................... 35
5.4.1
Menu Configuration list................................................................................................................ 35
5.4.2
Advanced Menu............................................................................................................................ 42
5.5
Display messages ...................................................................................................................... 44
5.5.1
Messages LED Panel .................................................................................................................. 44
5.5.2
Messages LCD Panel .................................................................................................................. 45
Web Panel and Internal Ethernet Interface.........................................................................................46
6.1
Summary .................................................................................................................................... 46
6.1.1
Introduction.................................................................................................................................... 46
6.1.2
Supported Environments............................................................................................................. 46
6.1.3
Network Interface and Cabling ................................................................................................... 46
6.1.4
Connecting the Printer................................................................................................................. 46
6.1.5
Network Interface Status ............................................................................................................. 46
1
Tally Dascom 2610
IP Configuration.......................................................................................................................... 47
6.2.1
Network IP Configuration ............................................................................................................ 47
6.2.2
Assigning the IP Address ............................................................................................................ 47
6.3
WebPanel ................................................................................................................................... 49
6.3.1
Introduction.................................................................................................................................... 49
6.3.2
Web Browser................................................................................................................................. 49
6.3.3
Access to WebPanel.................................................................................................................... 50
6.3.4
Printer Status................................................................................................................................. 50
6.3.5
Printer Configuration .................................................................................................................... 51
6.3.6
Printer Actions............................................................................................................................... 54
6.3.7
Load Configuration....................................................................................................................... 55
6.3.8
Save Configuration....................................................................................................................... 56
6.3.9
Retrieve Configuration From Printer.......................................................................................... 56
6.3.10
Send Configuration to Printer ................................................................................................... 57
6.3.11
Report........................................................................................................................................... 59
6.3.12
Reset Printer ............................................................................................................................... 59
6.3.13
Panel Lock On/Off...................................................................................................................... 59
6.3.14
Download Firmware................................................................................................................... 59
6.3.15
TallyCom Status.......................................................................................................................... 62
6.3.16
Advanced Configuration............................................................................................................ 63
6.3.17
General ........................................................................................................................................ 64
6.3.18
TCP/IP ......................................................................................................................................... 65
6.3.19
SNMP........................................................................................................................................... 66
6.3.20
Password..................................................................................................................................... 67
6.3.21
User Name .................................................................................................................................. 67
6.3.22
Resetting Password................................................................................................................... 67
6.3.23
Email Notification........................................................................................................................ 68
6.3.24
Logical Printers........................................................................................................................... 70
6.3.25
String Replacement Example Plain Text................................................................................. 71
6.3.25
Logout of TallyCom .................................................................................................................... 72
6.3.26
Restart TallyCom ........................................................................................................................ 72
6.3.27
Virtual Control Panel.................................................................................................................. 73
Addendum ............................................................................................................................................74
7.1
Character Set ............................................................................................................................. 74
7.2
Control Codes Summary ............................................................................................................ 79
7.2.1
PJL commands ............................................................................................................................. 88
7.2.2
Barcode.......................................................................................................................................... 88
7.2.3
List of available MTPL barcodes ................................................................................................ 89
7.2.4
US Postnet barcode..................................................................................................................... 89
7.2.5
Royal Mail Customer barcode .................................................................................................... 90
7.2.6
KIX barcode................................................................................................................................... 90
7.2.7
USPS Intelligent Mail barcode.................................................................................................... 90
7.2.8
LC printing ..................................................................................................................................... 91
7.2.9
List of additional control Codes .................................................................................................. 92
7.3
Interfaces Specifications............................................................................................................. 93
7.3.1
Parallel I/O IEEE 1284................................................................................................................. 94
7.3.2
Ethernet I/O 10/100 Mulitprotocol .............................................................................................. 95
7.3.3
USB 2.0 I/O – Full Speed ............................................................................................................ 96
7.3.4
Optional Serial Interface RS232C.............................................................................................. 97
Options and accessories.......................................................................................................................102
8.1
Options ..................................................................................................................................... 102
8.2
Consumables ........................................................................................................................... 103
8.3
Accessories .............................................................................................................................. 103
General Specifications .......................................................................................................................104
9.1
Printer Specifications ................................................................................................................ 104
9.2
Non-Scalable Fonts, Code Pages and National Character Sets............................................... 108
9.3
Paper Specifications ................................................................................................................. 110
9.3.1
Standard Tractor (Front, Rear and Pull position) – narrow and wide versions.................. 110
6.2
2
Tally Dascom 2610
10
9.3.2
Front Feed / Manual Insertion – Narrow and wide versions .................................................111
Maintenance ...................................................................................................................................112
10.1
Cleaning ................................................................................................................................. 112
10.1.1
Cleaning and Vacuuming the Printer..................................................................................... 112
10.1.2
Cleaning the Paper Rollers..................................................................................................... 112
10.2
Troubleshooting...................................................................................................................... 113
10.2.1
Print Quality Problems and Solutions ................................................................................... 113
10.2.2
Paper Handling Problems and Solutions.............................................................................. 114
10.2.3
Operating Problems and Solutions........................................................................................ 114
DASCOM REPRESENTATIVES ............................................................................................................... 115
Symbols used
Important information is highlighted in this manual by two symbols.
CAUTION highlights information which must be observed in order to
prevent injuries to user and damage to the printer.
NOTE highlights general or additional information about a specific
topic.
3
Tally Dascom 2610
Changes or modifications not expressly approved by the responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
--Consult the dealer or an experienced radio/TV technician for help.
4
Tally Dascom 2610
Printer at a glance
1.1
Unpacking the printer
Besides this manual, the package will contain: a power cord, a ribbon cartridge, a tractor, a CD
and 6 pieces of U-wire paper support.
Prepare for your printer
1
Tally Dascom 2610
1.2
Unpacking the Printer
Front View
Rear View
2
Tally Dascom 2610
For Fanfold
For Cut Sheets
3
Tally Dascom 2610
1.3
Parts description
1
Control Panel
2
3
4
5
Latch
Front Cover
Power Switch
Hand Wheel
6
Paper Support
7
8
Top Covers 1&2
Head Gap Lever
9
10
Paper Path Lever
Upper Friction
11
Power Socket
12
Interfaces
13
14
15
16
17
Mute Cover Latch
Print Head
Ribbon Cartridge
Tractors
Paper Guides
Left/Right
Cut Sheet Support
18
LED: The 2-line LED with 4 keys panel indicates the
operating status and allows simple settings of the printer;
LCD: A LCD display and two keys indicates the operating
status and allows simple settings of the printer.
Sliding it down unfolds the cut sheet support.
Unlocking the front cover unfolds the cut sheets support.
Turns on and off the printer.
Turn the knob to load or clear the paper. It should be
inserted the full way until you can hears some sort of
“Click”.
At slanted position, it stacks cut sheets; at flat position, it
separates fanfold printouts from incoming forms.
Protect the internal parts and reduce the noise.
Adjusts the gap between the print head and various
form thickness.
Selects various paper sources.
Guides the form when cut sheets or fanfold forms are
used.
A power cord is plugged into the socket to supply the
power.
The interface cable of the host computer is plugged into
one of the interfaces.
You must open it before you open the top cover 1.
Utilizes 24 needles to strike on ink ribbon and paper.
Holds the ink ribbon fabric.
Holds and transports fanfold forms.
Sliding the guides varies the form width and the left
margin on a cut sheet.
A flat surface supports a sheet or multi-part form.
4
Tally Dascom 2610
Installation
2.1
Placing the printer
Place the printer on a solid, flat, stable surface such that the printer sits firmly and cannot
move. Select an environment with sufficient ventilation, easy access to the control panel and
paper input areas as well as the printed output.
When selecting the printer location, observe the following additional requirements:
1) Never place the printer near to any flammable gas or explosive substances.ǂ
2) Do not expose the printer to direct sunlight. If you cannot avoid placing the
printer near a window, protect it from the sunlight with a curtain.
3) When connecting a computer to the printer, make sure the maximum
recommended cable length is not exceeded.
4) Ensure sufficient distance between the printer and any heating
devices/radiators.
5) Avoid exposing the printer to extreme temperature or air humidity fluctuations.
Above all, avoid dusty environments.
2.2
Connecting the printer
This printer is configured with a Parallel, USB and Ethernet interface as standard. An optional
Serial interface can be installed additionally.
5
Tally Dascom 2610
2.2.1
Parallel interface (IEEE 1284)
Make sure that the printer and the computer are switched off and connect the parallel cable
between the printer and the computer. Lock the connector with the 2 clips on the printer
interface connector; tighten up the 2 screws on the other end connecting to the computer.
2.2.2 USB 2.0 (Full Speed)
Plug in the USB cable to the printer and the computer.
2.2.3
Ethernet
6
Tally Dascom 2610
2.2.4
Serial Interface (RS-232C) as option
2.2.5 Connecting the power
Plug in the power cord to the printer power socket as shown in the diagram.
Connect the printer to the correct voltage power source.
2.2.6
Switch on the printer
Switch on the printer as shown in the diagram.
7
Tally Dascom 2610
2.3
Installing the ribbon cartridge
1) Switch off the power.
2) Unfold the top cover and follow the steps 1.2.3.4 in the below picture.
3) Flip the upper friction assembly
8
Tally Dascom 2610
4) Insert the ribbon cartridge till it is tightly locked in position.
5) Insert the ribbon fabric in between the print head and ribbon mask.
6) Turn the knob on the left hand side several times in order to tighten the fabric, and the
fabric will slides downwards into the correct position between printhead and ribbon mask
after the moving.
7) Restore the upper friction assembly to its original position.
Printhead may be hot, please move the printhead by moving the carriage.
9
Tally Dascom 2610
Installing the paper
The printer can handle either single sheets or continuous forms. The printer is able to print up
to 5 copies (original plus 5).
To ensure the print quality and protect the print head, set a proper print gap by the
gap lever (see 3.1) for the form thickness and do not load folded, damaged,
wrinkled, or curled paper.
3.1
Adjusting the print gap for various form thicknesses
The print gap lever is on the left side of the printer inside the top cover.
Take care to adjust the print gap lever to a suitable position whenever you change the number
of copies being printed. Using the wrong print gap may cause print head damage or paper
jams.
The recommended gap lever position for different form thickness is:
Paper type
1-part
Original + 1 copy
Original + 2 copies
Original + 3 copies
Original + 4 copies
Original + 5 copies
Lever position
The position “Ribbon” only is suitable for loading the ribbon. When the lever is set higher than
appropriate it will result in poor print. The ribbon and head life will be shortened.
10
Tally Dascom 2610
3.2
Paper path introduction
3.2.1
Cut sheet paper handling (front friction only)
1) Place the paper path lever to the cut sheet position.
2) Unlock the front cover with the latch to unfold the cut sheet support.
3) Adjust the gap lever if necessary; see 3.1.
4) It is recommended to align the left paper guide exactly to the mark > I <. This marks the
left edge of the stationery. Slide the right guide to the position of the right edge of the
stationery.
5) Insert the stationery straightly all the way into the guided slot until it stops.
6) Press the load key to feed the paper to the correct print position, automatically. The
printer clears the Paper End condition and goes into the ready or online state.
11
Tally Dascom 2610
3.2.2
Fanfold paper handling
3.2.2.1
Front push tractors for fanfold
1) Close the front cover if previously opened. Switch the paper path lever to one of the
desired tractor positions.
2) Move the paper path lever to the desired position.
3) Adjust the head gap lever if necessary.
4) Open the front cover by tilting the cover from bottom to the top, and make sure it’s locked in
place (see below pictures).
Lock the front cover in the way that is shown in the pictures.
Make sure the front cover is locked.
12
Tally Dascom 2610
5) If you do not need to adjust the left margin go to the next step. Open the right and left
tractor flaps, insert fanfold paper into the left-hand tractor, and make sure that at least
three paper transport holes are positioned on the tractor pins, close the tractor flap,
open the latch lever and align the tractor so that the first printing position on the paper
matches the IIIIXIIII mark on the printer housing, then lock the lever again.
6) Align the right-hand tractor to the width of the paper and insert the paper (Make sure that it
is inserted by the same length as on the left-hand tractor in order to avoid any paper jam).
Then close the tractor flap and slide the tractor to the right until the paper is slightly
tensioned, then lock the tractor.
7) Lower the front cover, switch the printer on.
For LCD: The active paper source (TrFront) appears in the display, the paper will
automatically load when the printer is in online mode and receives data from the
computer. Also, you can press the load key (key 4) only to load paper before starting the
printout.
For LED: The paper will automatically load when the printer is in online mode and
receives data from the computer. Also, you can press the load key (key 2) only to load
paper before starting the printout.
13
Tally Dascom 2610
3.2.2.2
Rear tractors for fanfold
14
Tally Dascom 2610
3.2.2.3
Top pull tractors for fanfold
For the stepsĸandĹ , please refer to the 2.3
15
Tally Dascom 2610
3.2.3
Top-Of-Form adjustment
For pull tractor (PullTr), follow the steps below to adjust the first print position:
1) Remove Paper from printer.
2) Power on the printer.
3) Lift the Top Cover so you can see the transparent ribbon guide in front of the print head.
4) Install the paper into the pull tractor.
5) Move the paper with the hand wheel so the perforation of the fanfold paper lies exactly at
the top of the transparent ribbon guide.
6) Close the Top Cover.
7) Press the Load key on the panel.
8) The printer now moves the paper to the correct first print position on a page (TOF).
16
Tally Dascom 2610
Control Panel Operation
General functions for the keys are clearly designated on the Panel label. Some other special settings
need pressing multiple switches simultaneously or holding some keys when powering on the printer.
This Chapter will describe the functions of the keys and display (LEDs or LCD) on the Panel.
4.1
Operation of the LED Panel
4.1.1 Keys and Indicators
On the Panel, there are four keys, each with its name from left to right:ɋOnlineɌ,ɋLoad/EjectɌ,
ɋSpeedɌandɋTearɌ. The names of five indicators from left to right are:ɋOnlineɌ,ɋTractorɌ,
ɋSpeedɌ,ɋPaper OutɌandɋPower/ErrorɌabove.
Please refer to the below diagram for the Panel layout:
Below describes the function of each key/indicator:
ƹ Indicators
1)ɋOnlineɌlights up to indicate online and turns off to indicate off-line.
2)ɋTractorɌlights up to indicate utilizing tractors and turns off to indicate front friction state.
3)ɋSpeedɌSpeed lights up to indicate higher print speed or is off if printing in higher quality based
on selected Font.
4)ɋPaper OutɌlights up to indicate out-of-paper warning and turns off to indicate paper loaded.
5)ɋPower/ErrorɌnormally lights up to indicate power on state. Please refer to 5.
Error Indications on LED for the description on flashing of this indicator.
17
Tally Dascom 2610
ƹ Keys
1)ɋOnlineɌ
a) Every press on this switch toggles the status between Online and Offline. When the printer is
Online, it receives data from the host; while it is Offline, it stops the printing and signals the host to
stop sending data.
b) Press the keyɋOnlineɌfor the below operations:
z Before and after special setup: Most of the special setup requires Offline operation. A
press onɋOnlineɌkey brings the printer Offline to carry out the special setup; after that,
pressingɋOnlineɌbrings the printer back online.
z Halt the printing for error recovery: PressingɋOnlineɌbrings the printer Offline for error
recoveries like paper jam and so on. After the recovery, pressɋOnlineɌto continue the
printing.
2)ɋLoad/EjectɌ
If paper is already loaded:
Single sheet - - > The printer ejects the paper;
Tractor front and rear - - > The printer moves the paper in to Park position.
If paper is not loaded:
Transport the paper to the first print position (TOF).
3)ɋSpeedɌ
Toggles between high speed and high quality print depending on menu settings.
4)ɋTearɌ
When fanfold stationery are installed in an active tractor path, a press of this key advances the
perforation of the stationery to the cutting edge of the tear-bar. This key is invalid for cut sheets.
18
Tally Dascom 2610
4.1.2
Online Operations
Function
Name
Offline
Switch
Operation
{S1}
Load/Eject
{S2}
Tear Off
{S4}
Function Description
LED light ON: Online; LED light OFF: Offline;
Load: Load the paper from active paper path to first print
position.
z Eject: Either park the fanfold paper or eject cut sheet
paper.
This is valid for tractor mode only. It feeds the form to the
tear-off position. After tearing off the form, printing starts on the
next TOF (top of form) by:
z pressing S4 once, or
z receiving print data from the host.
19
Tally Dascom 2610
4.1.3
Offline Operations
Function
Name
Online
Load/Eject
Switch
Operation
{S1}
{S2}
Speed
LF/FF
Setup Menu
Clear Buffer
and Reset
{S3}
{S4}
[S2] +[S3]
[S1] +[S2]
Function Description.
LED light ON: Online; LED light OFF: Offline.
Load: Load the paper from active paper path to first print
position.
Eject: Either park the fanfold paper or eject cut sheet paper.
Toggle Between HS-Draft /Draft or NLQ/LQ.
Brief press: Linefeed, Longer hold: Formfeed.
Enter Printer Setup Menu.
Clears the print buffer.
Initializes the printer to power on configuration.
20
Tally Dascom 2610
Detailed descriptions of the above functions:
ƹ Speed
If LQ font is currently set in the configuration, lighting up of theɋSpeedɌLED forces NLQ font
printouts; turning offɋSpeedɌindicates LQ printouts.
If Draft is currently set in the configuration, lighting up of theɋSpeedɌLED forces HS Draft printouts;
turning offɋSpeedɌindicates Draft printouts.
ƹ Setup Menu
See Chapter 5 for details.
ƹ Clear Buffer and Reset
The printer has high capacity storage (buffer) to store the data from the host computer. Sometimes it is
required to halt the printing to clear a fault. Resuming the printing at this point may cause erratic
printouts because some of the un-processed data in the buffer may be truncated. Therefore, it is
recommended clearing the buffer after the recovery with following procedures: (Turning off the printer
is an alternative)
1) Terminate the print job in the host.
2) Press theɋOnlineɌkey to bring the printer off-line. The printing will stop, but un-processed data
still resides in the buffer.
3) HoldɋOnlineɌand ɋLoad/EjectɌkeys simultaneously. The buffer will be cleared and the printer
will automatically warm boot.
4) Probably you need to repeat step 2-3 times as the print job in the host spooler may be very large.
21
Tally Dascom 2610
4.1.4
Power-On Operations
Function Name
Technical Setup
Switch Operation
[S1]
Menu Unlock
[S2]+[S3]
Status Page
[S4]
Load Defaults
[S1]+[S2]+ [S3]+[S4] z
Function Description
Start Technical Setup / Advanced Menu
(This also includes Self Test Mode).
Override Menu Lock Function if Menu is
locked.
Print Status Page.
Load Default Settings.
Detail descriptions of the above functions:
ƹ Technical Setup
See Chapter 5 for details.
ƹ Menu Unlock
PressingɋLoad/EjectɌandɋSpeedɌkeys simultaneously overrides. Menu unlock function if menu is
locked.
ƹ Status Page
Print the setup of the printer (Menu).
ƹ Load Defaults
Print the setup of the menu and the parameters.
22
Tally Dascom 2610
4.2
Operation of the LCD Panel
ƹ The Online mode is the printer’s normal operating mode. Data from your computer can be
received and printed.
ƹ In the Offline mode the link between printer and computer is interrupted, i.e. no data can
be received and printed.
ƹ In the Setup mode you can either select the printer menu or carry out the quick-switch
function. The quick-switch option was included so that you can change the most important
parameters (for example adjustments, character density, font, paper path, adjustments
directly without having to enter them via the menu. The settings for the parameters character
density and font are lost when the printer is switched off. They can be selected permanently in
the menu mode of the printer.
ƹ In the Menu mode further printer settings (line spacing, size of the interface buffer etc.) can
be altered and saved permanently.
4.2.1
The LC display
The LC display tells you all the important printer settings and informs you which functions are
currently assigned to which keys.
The upper line informs you that the printer is either in online or offline mode (in the example
below the printer is in the Online mode), and the selected paper path (below: TrFront = tractor
front mode).
23
Tally Dascom 2610
4.2.2 Online mode
After switching on, the printer is automatically set to online mode.
Only in this mode can it receive data from the computer.
Ŷ Online key: Toggle between Online and Offline mode.
Ŷ Tear key (4): Activates the tear function when fanfold paper
is loaded.
If Load is displayed above this key, no paper is loaded
in the printer or the paper is in park position. In this case the
display switches between Online and Park Position. Press
the key to feed paper to the printing position.
Ŷ Setup key: Sets the printer to setup mode.
4.2.3 Offline mode
Only in this mode is it possible to perform step, line, or form feeds from the control panel,
however, data cannot be received.
Ŷ Park key (1)
If fanfold paper is loaded in the printer, it is fed to the
park position or the tear position. If a single sheet is
loaded, it is ejected.
Ŷ © key (2)
Each press: Paper is transported upwards step by step.
Holding: Continuous transport upwards.
Ŷ ª key (3)
Each press: Paper is transported downwards step by step.
Holding: Continuous transport downwards.
Ŷ Load key (4)
No paper in the printer: The press on this key loads the
paper to the first print position.
Paper in the printer:
Each press: performs a line feed (LF).
Holding: performs a form feed (FF).
Ŷ Setup key: Sets the printer to setup mode.
Ŷ Online key: Sets the printer to online mode.
24
Tally Dascom 2610
4.2.4
Setup mode
In this mode, the following settings are available:
Ŷ Setup key: Sets the printer to setup mode, in which the
following settings can be selected.
Ŷ Menu key (1): Other menu settings. Access may be
disabled by menu settings (see note below).
Ŷ Adjust key (2): Sets the Tear position and first printing line
(TOF). If you have the PullTr (Pull - Tractor) selected Adjust
is not available.
Ŷ Char key (4): Sets the font and the number of characters per
inch temporarily.
Access to the other menu settings (Menu) may be disabled by the manufacturer.
Proceed as follows to release this lock temporarily.
1) Switch off the printer for approx. 5 seconds.
2) Switch the printer on again keeping the Setup key pressed.
4.2.5
Power on functions
If you keep one of the following keys pressed during power-on until the printer has completed
initialization, the corresponding function is activated:
ƹ If you keep the Online key depressed while turning on the printer, you enter the printer’s
advanced menu mode. The advanced menu mode is described in the section 5.4.2 of this
manual.
ƹ If you keep the Setup key depressed while turning on the printer, you regain access to the
printer menu if you had locked it before with the help of the Menu Lock function.
ƹ If all four function keys (keys 1 to 4) are depressed simultaneously while turning on the
power, all printer settings are reset to the default values, except the Forml (Form length)
setting in advanced menu mode.
ƹ Holding Function key 4 while turning on the printer prints out the parameter settings.
25
Tally Dascom 2610
Setting parameters for the printer
(Programming via the control panel)
Apart from being able to control your printer via the applications software you use, you can
also program the printer directly. There are two programming options you can use:
ƹProgramming via the control panel.
ƹProgramming via the interface using Escape sequences or control codes.
Settings made by escape sequences have priority over settings made in menu
mode; therefore they will override these.
Programming via the interface gives you far greater freedom for designing your printed pages,
however, it is also a more sophisticated method and requires some experience with
programming languages and printer control systems.
All programming via the interface is lost after you turn off the printer, whereas the
programming carried out using the control panel is saved and stored even after you turn off
the printer.
5.1
Setting the parameters through the LED Panel
This chapter describes the handing of the operator’s panel without optional display.
Firstly bring the printer Offline. PressingǏLoad/EjectǐandǏSpeedǐkeys simultaneously
activates the parameters setting operation.
5.1.1
Fine tuning the TOF and Tear positions
Below describes how to set TOF demonstrating the general procedures of parameters
configuration via an LED panel (This procedure is valid for front (TrFront) and rear tractor
(TrRear) only):
1) First load fanfold paper in one of the tractors and bring the printer Offline. Pressing
ǏLoad/EjectǐandǏSpeedǐkeys simultaneously activates the parameters setting
operation. The printer prints out 2 lines of key assignments valid for the parameter setting
operation.
Key 1
Key 2
Key 3
Key 4
Menu
Adjust
Char
2) PressǏLoad/Ejectǐ(i.e. Key 2 in the listed assignment) to enter the operation. The
printer then lists the below line.
TOF
Tear
3) ĀTOFāsets the first printing position from the top edge of the page. “Tear” sets the
desired perforation position. PressǏSpeedǐ(i.e. Key 3) to activate the TOF setting. The
printer responds with the below line.
FormAdj 12/72” *
Set
Exit
4) The printer feeds the form to a position where the bottom edge of the first printing line
(TOF) is aligned with the tear edge of the printer. PressǏLoad/EjectǐorǏSpeedǐto
26
Tally Dascom 2610
increment or decrement the TOF value. After adjustment, press Key 1 (Set) to save the
change.
Set the Tear position in the same way. Move the perforation of the stationery
exacly to the Tear Edge.
5.1.2 Select a font
Below example demonstrates how to select Roman LQ font type under the Char setting.
1) First, load fanfold paper to one of the tractors and bring the printer Offline. Pressing
ǏLoad/EjectǐandǏSpeedǐkeys simultaneously activates the parameters setting
operation. The printer prints out 2 lines of key assignments valid for the parameter
setting operation.
Key 1
Key 2
Key 3
Key 4
Menu
Adjust
Char
2) PressǏTearǐ(i.e. Key 4 in the listed assignment) to enter the Character setting. The
printer then lists the below line:
Font
CPI
3) “Font” allows selecting desired font type and “CPI” allows setting desired character pitch.
PressǏLoad/Ejectǐ(i.e. Key 2) to enter the Font submenu. The printer responds with the
below line:
HS-Draft *
Set
Exit
4) HS-Draft * indicates the current selection. Set means to save the change. < selects the
previous item. > selects the next item. Exit exits the menu. Here, pressǏSpeedǐ(i.e. Key
3) to show the next font. Keep pressingǏSpeedǐuntil the print shows Roman:
Roman LQ
Set
Exit
5) PressǏOnlineǐto save the change of font type to Roman. The printer sounds the
buzzer and prints the below line to confirm successful change.
Roman LQ *
Set
Exit
Modify the CPI in a similar way if desired (these two are only temporarily stored).
27
Tally Dascom 2610
5.1.3
Settings within Menu
Below example demonstrates how to select an Emulation within the Menu.
1) First load fanfold paper to one of the tractor and bring the printer Offline. Pressing
ǏLoad/EjectǐandǏSpeedǐkeys simultaneously activates the parameters setting
operation. The printer prints out 2 lines of key assignments valid for the parameter setting
operation.
Key 1
Key 2
Key 3
Key 4
Menu
Adjust
Char
2) PressǏOnlineǐ(i.e. Key 1) to get into Menu operation. The printer prints:
Back
Print
Menu
Next
3) PressǏTearǐ(i.e. Key 4) repeatedly till “Emulation” appears on the printout:
Back
ESCChar
Emulation
Next
4) PressǏSpeedǐ(i.e. Key 3) to get into emulation configuration. The printer prints:
Epson LQ-2550 *
Set
Exit
5) Epson LQ-2550 * indicates the current emulation is LQ-2550. Set means to save the
change. < selects the previous item. > selects the next item. Exit leaves the menu. Press
ǏSpeedǐ(i.e. Key 3) to show the next emulation:
Epson LQ-2170
Set
Exit
6) Press ǏOnlineǐ (i.e. Key 1) to save the selection of Epson LQ-2170 emulation. The printer
sounds the buzzer and prints the below line to confirm successful change.
Epson LQ-2170 *
Set
Exit
See 5.4.1 for a full list of valid settings.
28
Tally Dascom 2610
5.2
Setting the parameters through the LCD Panel
This chapter describes the handling of the operator’s panel with optional display.
5.2.1
Enabling access to menu mode
The menu can be locked by default to protect it from accidental or unauthorized access.
Proceed as follows to release this lock temporarily.
1) Switch off the printer for approx. 5 seconds.
2) Switch the printer on again keeping the Setup key pressed.
Calling up the menu
You can access the menu in the following way:
Press the Setup key. The printer switches to Setup
mode. (The Setup mode can be selected both in the
Online and Offline mode)
To access the printer menu, press the key directly
underneath the word Menu (1).
29
Tally Dascom 2610
5.2.3
Menu configurations
Every printer is shipped with factory default settings. Basic settings such as emulation,
character size, form length etc., which many applications make use of, are set. At the end of
this chapter you will find a menu printout which shows you the printer’s default settings.
Your printer allows you to set and use five independent menu configurations. If one of your
applications, for example, requires an IBM printer while another program works better with an
EPSON printer, you can set an IBM emulation configuration with the desired settings, and set
the second configuration as an EPSON emulation.
The active menu is always the one you used last. When you switch on the printer for the very
first time, menu no. 1 is loaded. Menu no.1 only remains active until you load another menu.
The last active menu is stored even after the printer is switched off and is reloaded
automatically when the printer is switched on again.
For example, to change from menu no. 1 to menu no. 3:
Press Setup key.
Press Menu (1) key.
Press Menu (3) key.
Now the following message appears in the LC display:
Now press the < (2) or > (3) key repeatedly until Load Menu=3
appears.
Then select menu no. 3 as the current setting using the Set key
(1). The currently active setting is marked with an asterisk (*).
If changing menus it is possible that the printer initializes due to different
emulation settings.
30
Tally Dascom 2610
Menu Printout
31
Tally Dascom 2610
5.2.4
Menu handling
You can navigate in the current menu using the four function and selection keys arranged
below the LC display field. Each function and parameter displayed in the LCD is executed or
selected by the corresponding key below, respectively. Usually two parameter groups are
combined at one level. In the following example, these are the LPI and Skip parameter
groups.
If you do not wish to change one of the two parameters you can either press the Next key (to
access the two following parameter groups in the menu), or you can press the Back key (to
access the two previous parameter groups in the menu).
If you want to change a setting, (e.g. the line density), then press the LPI key (LPI = lines per
inch) to access the actual parameter level.
The currently valid setting is marked by an asterisk (in the example below the current
setting is 6 lpi). With the < and > keys you can view the other parameters available for
this setting.
Example:
Save settings
Once the desired parameter is displayed on the LC display, you can save it by pressing the Set
key. The parameter is then set and the printer automatically displays the parameter groups
again. With the Exit key you can leave the sublevel without saving your changes.
32
Tally Dascom 2610
5.2.5
Selecting the LC display language
This section describes how to make settings in the menu, using the selection of the national
language as an example.
In this user guide all LC display messages are shown in English language. Your printer offers
also the possibility to show the display messages in German, French, Italian, Spanish or
Turkish language. This example shows how to change from the English language to the
German language. The same procedure applies to the other languages (French, Italian,
Spanish and Turkish).
Select the Setup mode by pressing the Setup key.
Setup mode and Menu mode may be disabled. Hold
down the Setup key while switching on the printer to
enable menu mode. If you want to enable access to this
mode permanently, you need to change the appropriate
setting in the menu.
Press the next key (4) several times until the display indicates
Language.
Press the Language key (3).
The display now changes to Parameter mode and indicates
English in the top line.
The lower line displays Set and Exit. The two arrows < (2)
and > (3) represent the symbols for parameter selection
(“<” indicates descending and “>” ascending). Press the <
(2) or > (3) key until the desired language is displayed, in
our example German.
Save your selection by pressing the Set key (1). An acoustic
signal verifies this action.
You can exit Parameter mode without saving a setting by
pressing the Exit key (4), the old setting is retained.
After saving your setting (Set), the display in our example
Ges.Men indicates the following text:
This setting is retained even after switching off
your printer.Terminating Setup mode press either
the Setup key to change into Offline mode or the
Online key to change to Online mode.
33
Tally Dascom 2610
5.3
Menu structure
The menu structure of your printer may be slightly different from the example shown here,
depending on the printer software.
ĕNext
MENU
Backė
Print
Menu
LeftMrg
Reset
Quietm
FFmode
Font
CPI
Barcode
Barmode
LPI
Skip
Eject
Width
ESCChar
Emulate
Bidir
I/O
1)
Serial
Paper
Interf.
Buffer
1)
Format
Baud
1) 2)
Special
CG-Tab
Protocol
1)
ETH-INT
1)
1)
DTR
CharSet
1) Only with optional serial interface
2) Only if ENQ/STX, ETX/ACK or ACK/NAK protocol is selected
34
RightMrg
Auto Tear
Single
Tr Front
Tr Rear
Pull Tr
MenLock
Language
Auto-CR
Auto-LF
Country
Sl.Zero
Tally Dascom 2610
5.4
Full list parameters setting
In order to meet individual requirements of printer functionality, users may modify the
printer configuration settings accordingly as follows: start by pressing [Load/Eject] +
[Speed] in offline mode. The printer will enter Main Menu settings setup mode. Follow the
instructions printed on how to do the required setting changes. When a new setting is
saved, it becomes effective, even when printer is power cycled.
5.4.1
Menu Configuration list
Menu
Adjust
Valid Settings
TOF
Function
Tear
Setting the tear position.
Setting the first printing line (TOF).
Print the menu settings.
Print
Menu
Load Menu=1
Load Menu=2
Load Menu=3
Load Menu=4
A menu is loaded, you can choose
between five menus.
Load Menu=5
Reset
Reset Menu Yes
Quietm
Off On
Font
HS-Draft
No
Roman LQ
Press the No (1) or Yes (2) key to select
the desired setting.
All manually altered settings in the current
menu are lost when it is reset to the
default settings.
We therefore recommend that you print
out the menu first.
Switches between normal and quiet mode
printing. For all printing
modes, the print-out is made with the
bidirectional method in quiet mode
printing. In the first step the first row of
pins is activated, during the second step
the second row is used.
Draft
Roman NLQ; This parameter selects the character style
Roman PS NLQRoman PS LQ and its quality permanently.
CourierNLQ
Sans Serif NLQ Sans Serif LQ
Courier LQ
S Serif PS NLQ S Serif PS LQ
35
Tally Dascom 2610
Prestige NLQ Prestige LQ
Script NLQ
Script LQ
OCR-B NLQ
OCR-B LQ
OCR-A NLQ
OCR-A LQ
Orator NLQ
Courier I NLQ Courier I LQ
Orator LQ
Souvenir NLQ Courier I PS NLQ Gothic NLQ
Souvenir LQ
CPI
LPI
Skip
Courier I PS LQ
Gothic LQ
10 CPI, 12 CPI, 15 CPI, 17.1 CPI, 20 Sets the characters per inch (character
pitch). The higher parameter the smaller
CPI, 5 CPI, 6 CPI, 7.5 CPI, 8.6 CPI.
character spacing.
6 LPI, 8 LPI, 12 LPI, 2 LPI, 3 LPI, 4 LPI. Sets the lines per inch (line density). The
higher parameter the smaller line spacing
(random LPI can be selected via the ESC
sequences).
Skip=0.0 Inch, Skip=0.5 Inch,
Skips the perforation; 7 different values
(in inches) can be defined.
Skip=1.0 Inch, Skip=1.5 Inch,
Skip=2.0 Inch, Skip=2.5 Inch,
Skip=3.0 Inch, Skip=3.5 Inch.
ESCChar ESC
Emulate
ESC+$$
Selects the start signal for control
sequences. Setting ESC: Only character
Escape can be used. Setting ESC+$$:
Character Escape or alternatively two $
characters ($$) can be used.
Selects the emulation. When a printer
understands the control set written for
another printer type, it is said to emulate
the other printer.
Epson LQ-2550
Epson LQ-2170
IBM Propr. XL24
IBM ProXL24+AGM
Bidir
Bidir=On Bidir=Off
I/O
Serial
Baud
MTPL
Setting On: Printer prints in both
directions (bidirectional).
Setting Off: Printer prints only in one
direction (from left to right).
Selects the data transmission rate (baud
rate) (baud=bit per second).
Baud=9600
Baud=9200
Baud=600
Baud=1200
Baud=2400
Baud=4800
36
Tally Dascom 2610
Format 8Bit No 1Stop
8Bit No 2Stop
8Bit Even 1Stop
This parameter serves to define the
number of data bits, the parity check for
received data bytes and the number of
stop bits per data byte.
8Bit Odd 1Stop
8Bit Mark 1Stop
8Bit Spc 1Stop
7Bit No 2Stop
7Bit Even 1Stop
7Bit Odd 1Stop
7Bit Odd 2Stop
7Bit Mark 1Stop
7Bit Spc 1Stop
7Bit Mark 2Stop
7Bit Spc 2Stop
Protocol XON/XOFF
RobustXON/XOFF
ENQ/STX
This parameter serves to select the type
of protocol, i.e. a certain set of rules and
procedures for ensuring error-free data
exchanges between computer and
printer.
ETX/ACK
DTR
ACK/NAK
DTR=DTR
Defines the conductor to which the DTR
signal is connected
(DTR=Data Terminal Ready).
Selects the interface. Printer is configured
either for parallel. Ethernet or optional
serial connection or in automatic change
for the parallel or the optional serial
interface (Shared).
Selects the size of the interface buffer.
DTR=READY
Interf.
Interf.=Share
Interf.=Parallel
Interf.=Serial
Buffer
Buffer=0 KB
Buffer=32 KB
Buffer=64 KB
Buffer=96 KB
Buffer=128 KB
Buffer=160KB
Buffer=192KB
Buffer=224KB
Buffer=256KB
37
Tally Dascom 2610
ETH-INT
IP-Addr
Octets 1-4
0 to 255
Input of the IP address of the printer
This menu level offers the possibility to
set the IP address, which is divided into
four digit groups (octet 1 to 4).
Input of the Gateway address of the
printer.
Gateway Octets 1-4
0 to 255
Subnet
Octets 1-4
0 to 255
IP Get M DHCP
Static
Banner
EthSpeed
Input of the Subnet mask address of the
printer.
BOOTP Selects the way of administrating the IP
address.
Off On
Auto-Sense
10Mbit Half
10Mbit Full
100Mbit Half
100Mbit Full
CG-Tab
Graphic
DLL Italic
CharSet
Extended
Standard
Country
E-USASCII
E-France
E-German
E-UK
E-Denmark I
E-Sweden
E-Italy
E-Spain I
E-Japan
E-Norway
E-Denmark II
E-Spain II
E-L.America
E-Korea
E-Legal
ISO8859-1
ISO8859-1 SAP ISO8859-2
ISO8859-5
ISO8859-7
ISO8859-9
ISO8859-15
ELOT-928
BRASCII
Abicomp
Roman8
US-ASCII
French
German
Italian
Swedish
Norwegian
Spanish
Portuguese
Greek DEC
Cro-ASCII
38
Specifies whether a banner page is to be
printed out, when using the LPD/LPR
protocol.
The transmission speed is detected
automatically.
Sets the transmission speed to 10 MBit
half duplex per second.
Sets the transmission speed to 10 MBit
full duplex per second.
Sets the transmission speed to 100 MBit
half duplex per second.
Sets the transmission speed to 100 MBit
full duplex per second.
Only available for Epson
LQ-2550/LQ-2170 emulation. Either the
Epson character set Italics or the IBM
graphics character set or a DLL
(download) character set, as defined
before, can be activated in the code
range from hex. A0 to hex. FE.
Selects the IBM standard characters or
the extended IBM characters.
Selects the national character set. These
character sets can be used according to
the selected emulation.
Tally Dascom 2610
Coax/Twinax
Table 437
New-437
Table 737
775 Baltic
Table 850
New-Dig 850 Table 851
Table 852
Table 857
Table 858
Table 860
Table 861
Old-Code 860
Table 863
Flarro 863
Table 865
865 Hebrew
Table 866
866 Bulgaria
866 Ukraine
866 Kazakhst Kamenicky
Mazovia
Siemens Turk DEC Turkish
Table 1250
Table 1251
Table 1252
Table 1253
Table 1254
Table 1257
Sl.Zero
Sl.Zero=Off
AutoCR
On Off
AutoLF
Off On
Menlock
Off Menu
Language English
Spanish
Paper
Single
Sl.Zero=On
All
German
French
Turkish
TrFront
TrRear
Selects if normal zero (0) or the slashed
zero (Ø) is printed.
Switches the automatic carriage return on
or off after receiving the signal LF (line
feed).
Switches the automatic line feed (LF) on
or off after receiving the signal CR
(carriage return).
With MenLock=Off, all functions and
settings are accessible without restriction
in Online, Offline and Setup mode.
If MenLock=Menu is activated, all
functions and settings are still accessible
in Online and Offline mode, however, in
Setup mode you can only access the
parameter groups Adjust (setting the print
head gap [Head], top of form [TOF] and
tear position [Tear]), Paperway (setting
the paper path), Font (setting the font)
and the character spacing (CPI), while
access to Menu mode (Menu key) is
disabled.
If you select MenLock=All, you can
access the Online/Offline, Load/Park,
Paper and Paper Feed (LineFeed/Form
Feed, / ) functions in Online and Offline
mode while Setup mode is disabled.
In this case, the Setup menu can only be
called up by holding the key Setup while
switching on the printer.
Italian The menu can be shown in six
languages.
PullTr
39
Selects the paper parameters Formlen
(form length), FormAdj (first printing
position/TOF) separately for each paper
source in the current menu.
Tally Dascom 2610
Formlen
Lines
=6 – 144
Sets the form length via line formats.
Please note that the adjustment in Lines
depends on the selected LPI. For
example 8 LPI at a selected line number
of 96 lines results in a form length of 12
inches (96lines/[8lines/inch]) = 12 inches.
The selectable range is between 3 and 21
inches, i.e. for 2 LPI from 6 to 42 lines
and for 12 LPI from 24 to 262 lines.
If the form length is set it will not be
changed by changing the LPI later on.
Selects the form length by standard
formats. Using Standard, different paper
formats can be selected directly, e.g. DIN
A4, Legal, Letter.
The Menu indicates No format if a value
is selected by the Line function or ESC
sequences, which does not correspond to
a standard format.
Default 6LPI = 66
Standard
No format
DIN A3 (420 mm)
DIN A4 (297 mm)
DIN A5 (210 mm)
DIN B5 (250 mm)
DIN B6 (176 mm)
DIN C6 (162 mm)
Executive 10.5"
Letter 11"
Fanfold 12”
Legal 14"
FormAdj FormAdj=0 - 134/72”
Sets the first print position of a form in
n/72 inch, separately adjustable for each
paper path.
The auto tear function or the auto view
function can be selected as desired.
When auto view is switched on, the last
printed text is visible. As soon as data is
received the paper moves to the “normal”
print position. After printing the printer
waits for the given interval to bring the
paper once more to the auto view
position.
The paper is in the tear off position when
auto tear is switched on, the perforation of
the positioned at the tear off edge of the
printer. If data is received, the paper
returns to the normal print position. After
printing, the printer waits for the given
interval to bring the paper once more to
the tear off position. If the tear off edge
does is not aligned with the perforation of
the paper then this can be corrected.
Selects the line length in inches. With the
setting of 8 Inch, the printer operates like
Default 12/72”
Autotear ViewTear =Off
View=1s/3s/6s
Tear=1s/3s/6s
Tear at TOF
Width
Width=13.6Inch
40
Tally Dascom 2610
Width=8Inch
a printer with a width of only 8 inches.
Width=13.2Inch
Eject
This is valid for single sheet mode only. It
controls the exit direction of the friction
sheet paper.
With this function selected it is possible to
print different barcodes and LCP (Large
Character Printing).
Allows printing of normal characters on
the left and right of the barcode.
Eject=Top
Eject=Front
Barcode
Off On
Barmode Unsecured
Secured
FFmode
Off
On
LeftMrg
LeftMrg=0 - 134/10”
Specifies whether a form feed is to be
performed when the paper reaches the
top print line.
The left print margin can be set to a fixed
value.
The right print margin can
be set to a fixed value.
RightMrg RightMrg=2 - 136/10”
41
Tally Dascom 2610
5.4.2
Advanced Menu
Advanced
Valid Settings
Menu
Function
ASCII80
8 inch wide print of test pattern
ASCII136
13.6 inch wide print of test pattern
H-Dump
Formlen
12”
11”
Paphand
Physlm
CX-bid
CX-bid=ON
Physlm=0 - 30/10”
CX-bid=OFF
Wrap
Wrap=On
Wrap=Off
Sound
Sound=On
Sound=Off
42
To check operational readiness, your
printer contains a self-test routine which
allows testing of the printer
configuration, the print quality and
correct operation of your printer
With the interface test
(Hex-Dump/H-Dump) you can test data
transmission from the computer to the
printer. During this test, the data from the
computer is printed out in two columns.
The text in the left column is printed in
hexadecimal format and in the right
column in ASCII format.
The Formlen function allows you to set
the basic (default) form length to meet
your requirements. 11 inches are usual
in the USA, as opposed to 12 inches in
Europe.
Permanent (physical) setting of the left
margin. This parameter cannot be
changed by emulation dependent
margin settings. Margin setting values
entered by ESC sequences are added to
the Physlm.
CX-bid=ON sets the parallel interface of
the printer to bidirectional mode (IEEE
1284, Nibble mode), e.g. for Windows
Plug & Play.
CX-bid=OFF sets the interface to
compatibility mode in order to ensure
reliable operation with special external
boxes.
Wrap=On: If more characters than can
be printed are transmitted per line, the
characters which cannot be printed on
this line are printed at the beginning of
next line.
Wrap=Off: If more characters than can
be printed are transmitted per line, the
characters which cannot be printed on
this line are cut off.
When Sound=On, a beep is generated
every second to notify that paper is
empty
Tally Dascom 2610
Pap.back
Pap.back=normal is the standard for
normal paper.
Pap.back=dark can be set to process
paper with a grey back.
Paper with a completely black back side
cannot be used if the ink is
carbon-based. However, the printer can
handle aniline- based black paper
(undefined colors).
If you set HvyForm=ON, the printer
prints the same line twice at double
strike. This setting ensures that copy
paper produces optimum results.
With the SerialN function you have the
possibility to change the 12 digit serial
number of the printer. The number can
be written with any ASCII character
between hex 20 and hex 7E.
Pap.back=normal
Pap.back=dark
Hvy Form
HvyForm=ON
HvyForm=OFF
SerialN
AssetN
GrSpeed
factory set
LED Panel: The Serial Number cannot
be set via menu instead you need to use
the WebPanel
With the AssetN function you have the
possibility to change the 10 digit asset
number of the printer. The number can
be written with any ASCII character
between hex 20 and hex 7E.
10 digits empty
LED Panel: The Asset Number cannot
be set via menu instead you need to use
the WebPanel
This parameter allows improved Graphic
Speed independently to the driver. It
affects only the print speed of graphic
printouts at 180 x 180 dpi.
This parameter activates the printer
language PJL (Printer Job Language) in
Connection with the internal Ethernet
interface (ETH-INT) or the external
TallyCom III interface (ETH-EXT).
Ultra Draft=on, speeds up 17.1 and 20
cpi. Precondition is HS-Draft needs to be
activated
GrSpeed=Normal
GrSpeed=High
Jobcntl
Jobcntl=On
Jobcntl=Off
UltraDr
UltraDr=on
UltraDr=off
43
Tally Dascom 2610
5.5
Display messages
If the printer detects an internal fault or user error or if it expects you to do something, a
message will appear in the LC display (LED’s display message reference below table 5.6.1).
It also displays the status during an operation (e.g. Initializing). Below you will find a list of
messages with brief descriptions of each message.
5.5.1
Messages LED Panel
LED Messages Error/Power ON
Online
Tractor
Speed
Pap.Out
Power/Err.
Hardware Alarm
blink
blink
blink
blink
blink
Switch Paper lever (interm
beep)
Off
normal
normal
blink
blink
Paper Width Error
blink
off
blink
blink
blink
EEPROM Error
blink
blink
off
blink
blink
Serial Interface Error
blink
blink
blink
off
blink
“Printhead Hot” Message
blink
off
off
blink
blink
“Check Ribbon” Message
blink
off
off
off
blink
Serial Boot Mode
on
on
off
on
Off
Parallel Boot Mode
on
off
off
on
off
RAM Error
off
on
on
on
off
Missing FPGA
off
on
on
on
on
Monitor Mode for ROM
Debugger
on
on
on
off
off
Wrong Header (temporary)
on
off
off
off
off
Sensor Controller (ST8) Error
off
off
on
on
off
Firmware Download Is
Running
One lit LED is moving around in a circle, the others
are off
44
Tally Dascom 2610
5.5.2
Messages LCD Panel
LCD Messages
Meaning
Initializing
The printer cannot eject the paper/advance it to
park position.
Internal hardware error, contact your dealer or
service technician.
The print head is too hot. The printer will reduce
its print speed.
This message appears during the printer’s
initializing phase after switching on the printer.
Load error
The printer fails to load the paper.
Eject error
Hardware Alarm
Head hot
Parity error
Factory defined parameters will be reloaded in all
available menus after switching on the printer.
The printer has detected paper end during
operation/printer was switched on with no paper
loaded.
A parity error during data transmission is
indicated.
Park position
Printer was switched on with no paper loaded.
Press any key
The user is requested to press any key.
Loading default
Load paper from
Selftest
Tear Paper off
Switch Paper Lever
After power-on, the printer executes a short
hardware self-test.
The user is requested to tear off paper which has
been advanced to the tear.
Choose correct paper path. Turn paper lever
45
Tally Dascom 2610
Web Panel and Internal Ethernet Interface
6.1
Summary
6.1.1
Introduction
It is assumed you have the following:
ƹA working knowledge of your network system and related utilities.
ƹ Access to the supervisor or administrator account as a network administrator.
6.1.2
Supported Environments
The built-in network interface supports the following platforms and protocols:
ƹ Microsoft® Windows® NT 4.0, 2000, XP,7,8, Server 2003/2008/2012
ƹ Linux – Red Hat®, SuSE®
ƹ Unix® – Sun Solaris®, HP-UX®, IBM AIX®
ƹ TCP/IP, HTTP, LPR/LPD
6.1.3
Network Interface and Cabling
The printer requires:
ƹ Ethernet 10Base-TX or 100Base-TX interface.
ƹ Category 5e or 6 Ethernet cable with RJ-45 socket connectors.
6.1.4
Connecting the Printer
Connect the Ethernet cable to the network interface port RJ-45 connector on the rear center
of the printer.
6.1.5
Network Interface Status
There are two status lights (LEDs) next to the RJ-45 connector on the rear panel.
ƹ Right green light (Link Status) is solid: This shows the printer is connected to the network.
ƹ Right green light is blinking: Shows network activity.
ƹ Left yellow light (Duplex Status) is solid: Shows network interface is in full duplex mode.
Unless the link status light is green, the printer will not be able to connect to the
Network.
46
Tally Dascom 2610
6.2
IP Configuration
6.2.1
Network IP Configuration
The network interface of the printer requires an IP address.
There are several ways to assign an IP address to the printer:
ƹ DHCP (A Dynamic Host Configuration Protocol server assigned IP address.)
ƹ Static (An IP address obtained from your network administrator added to the printer
manually.)
ƹ BOOTP (Bootstrap Protocol server assigned IP address.)
6.2.2
Assigning the IP Address
If the printer menu is locked, please see the 4.2.5.
1. Automatic DHCP IP address assignment:
ƹ Press , then Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0 (Windows) Create Date : 2012:12:13 14:52:41+08:00 Modify Date : 2012:12:13 14:52:41+08:00 Metadata Date : 2012:12:13 14:52:36+08:00 Document ID : uuid:B51654ADF144E21197BE93C89D4F8F54 Instance ID : uuid:177b9f87-fe6f-4124-a11a-a23cc7c71f8f Derived From Instance ID : uuid:7beaad2d-4662-4415-a243-969389a49e13 Derived From Document ID : uuid:33298e8f-29da-4143-8ad5-ad0fc31b7618 Format : application/postscript Title : Microsoft Word - 2610_UG_LED&LCD__12_12_04_00.doc Creator : hp Page Count : 80 Author : hpEXIF Metadata provided by EXIF.tools