John Deere 5103E 5103 5103S 5203 5104 5204 Users Manual 043025UNIT
!! John-26 John Deere Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection
5103E, 5103, 5103S, 5203, 5104, 5204 to the manual 13e55f8e-9640-eb94-e527-19f180da91ca
2015-02-03
: John-Deere John-Deere-5103E-5103-5103S-5203-5104-5204-Users-Manual-466074 john-deere-5103e-5103-5103s-5203-5104-5204-users-manual-466074 john-deere pdf
Open the PDF directly: View PDF 
.
Page Count: 194
| Download | |
| Open PDF In Browser | View PDF |
5103E, 5103, 5103S,
5203, 5104 And 5204
Tractors
OPERATOR’S MANUAL
5103E, 5103, 5103S, 5203, 5104 And
5204 Tractors
OMRE73705 Issue A7 (ENGLISH)
CALIFORNIA
Proposition 65 Warning
Diesel engine exhaust and some of its constituents are
known to the State of California to cause cancer, birth
defects, and other reproductive harm.
If this product contains a gasoline engine:
WARNING
The engine exhaust from this product contains chemicals
known to the State of California to cause cancer, birth
defects or other reproductive harm.
The State of California requires the above two warnings.
John Deere Equipment Private Limited
Printed in India.
Introduction
Foreword
READ THIS MANUAL carefully to learn how to operate
and service your machine correctly. Failure to do so
could result in personal injury or equipment damage.
This manual and safety signs on your machine may
also be available in other languages (see your John
Deere dealer to order).
THIS MANUAL SHOULD BE CONSIDERED a
permanent part of your machine and should remain
with the machine.
MEASUREMENTS in this manual are given in both
metric and customary U.S. unit equivalents. Use only
correct replacement parts and fasteners. Metric and
inch fasteners may require a specific metric or inch
wrench.
RIGHT-HAND AND LEFT-HAND sides are determined
by facing the direction of forward travel.
WRITE TRACTOR SERIAL (CHASSIS) NUMBER in
the Specification or Identification Numbers section.
Accurately record all the numbers to help in tracing the
machine should it be stolen. Your dealer also needs
these numbers when you order parts. File the
identification numbers in a secure place off the
machine.
BEFORE DELIVERING THIS MACHINE, your dealer
performed a predelivery inspection. After operating for
the first 100 hours, schedule an after-sale inspection
with your dealer to ensure best performance.
THIS TRACTOR IS DESIGNED SOLELY for use in
customary agricultural or similar operations
("INTENDED USE"). Use in any other way is
considered as contrary to the intended use. The
manufacturer accepts no liability for damage or injury
resulting from this misuse, and these risks must be
borne solely by the user. Compliance with and strict
adherence to the conditions of operation, service and
repair as specified by the manufacturer also constitute
essential elements for the intended use.
THIS TRACTOR SHOULD BE OPERATED, serviced
and repaired only by persons familiar with all its
particular characteristics and acquainted with the
relevant safety rules (accident prevention). The
accident prevention regulations, all other generally
recognized regulations on safety and occupational
medicine and the road traffic regulations must be
observed at all times. Any arbitrary modifications
carried out on this tractor will relieve the manufacturer
of all liability for any resulting damage or injury.
SETTING FUEL DELIVERY BEYOND PUBLISHED
factory specifications or otherwise overpowering will
result in loss of warranty protection for this machine.
NR25796,0000344 –19–17JAN07–1/2
022607
PN=2
PY6069
PY6072
–UN–06AUG06
–UN–06AUG06
Introduction
John Deere 5103E Ttractor
PY6077
PY6071
–UN–06AUG06
–UN–06AUG06
John Deere 5103 Tractor
John Deere 5203 Tractor
PY6840
PY6839
–UN–11JAN07
–UN–11JAN07
John Deere 5103S Ttractor
John Deere 5204 Tractor
John Deere 5104 Tractor
NOTE: Tractor shown may have optional equipment.
NR25796,0000344 –19–17JAN07–2/2
022607
PN=3
Introduction
022607
PN=4
Contents
Page
Page
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05-1
Restart Stalled Engine . . . . . . . . . . . . . . . . . . . . 45-8
Avoid Idling the Engine. . . . . . . . . . . . . . . . . . . . 45-8
Observe Engine Work and Idle Speeds . . . . . . . 45-9
Working With Speed/Hour Meter . . . . . . . . . . . . 45-9
Stopping the Engine . . . . . . . . . . . . . . . . . . . . . 45-10
Using Booster Battery. . . . . . . . . . . . . . . . . . . . 45-11
Safety Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Controls and Instruments
Tractor Controls . . . . . . . . . . . . . . . . . . . . . . . . . 15-1
Instrument Panel . . . . . . . . . . . . . . . . . . . . . . . . 15-3
Instrument Panel (5103E Tractor). . . . . . . . . . . . 15-3
Lights
Light Switch Positions. . . . . . . . . . . . . . . . . . . . .
Using Headlights . . . . . . . . . . . . . . . . . . . . . . . .
Using High Beam Indicator . . . . . . . . . . . . . . . . .
Using Tail Lights. . . . . . . . . . . . . . . . . . . . . . . . .
Using Turn Signals . . . . . . . . . . . . . . . . . . . . . . .
Using Hazard Lights . . . . . . . . . . . . . . . . . . . . . .
Using Flood Lamp . . . . . . . . . . . . . . . . . . . . . . .
Seven-Terminal Outlet . . . . . . . . . . . . . . . . . . . .
Driving the Tractor
Operator Training Required . . . . . . . . . . . . . . . .
Driving on Public Roads . . . . . . . . . . . . . . . . . . .
Operating Transmission . . . . . . . . . . . . . . . . . . .
Shifting Transmission . . . . . . . . . . . . . . . . . . . . .
Operating Transmission . . . . . . . . . . . . . . . . . . .
Selecting a Gear . . . . . . . . . . . . . . . . . . . . . . . .
Using Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using Differential Lock (Optional For 5103E
Tractor ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stopping Tractor. . . . . . . . . . . . . . . . . . . . . . . . .
20-1
20-2
20-2
20-3
20-4
20-5
20-6
20-6
Operator’s Platform
Selecting Seat Position. . . . . . . . . . . . . . . . . . . . 25-1
Adjusting Ride Comfort. . . . . . . . . . . . . . . . . . . . 25-1
50-7
50-8
Rockshaft and 3-Point Hitch
Match Tractor Power to Implement. . . . . . . . . . . 55-1
3-Point Hitch Components . . . . . . . . . . . . . . . . . 55-1
Rockshaft Control Levers . . . . . . . . . . . . . . . . . . 55-2
Setting Position Control Lever Stop . . . . . . . . . . 55-2
Using Rockshaft Position Control . . . . . . . . . . . . 55-3
Using Draft Control. . . . . . . . . . . . . . . . . . . . . . . 55-4
Adjusting Rockshaft Rate-of-Drop/
Implement lock . . . . . . . . . . . . . . . . . . . . . . . . 55-5
Attaching Tipping Trailer. . . . . . . . . . . . . . . . . . . 55-5
Preparing Implement . . . . . . . . . . . . . . . . . . . . . 55-6
Positioning Center Link. . . . . . . . . . . . . . . . . . . . 55-7
Attaching Implements to 3-Point Hitch . . . . . . . . 55-8
Adjusting Hitch Side Sway . . . . . . . . . . . . . . . . . 55-9
Leveling the Hitch. . . . . . . . . . . . . . . . . . . . . . . 55-10
Adjusting Lateral Float . . . . . . . . . . . . . . . . . . . 55-11
Adjusting Rockshaft Control Lever Friction . . . . 55-11
Warming Hydraulic System Oil . . . . . . . . . . . . . 55-12
Break-In Period
Observe Engine Operation Closely. . . . . . . . . . . 35-1
Break-In Service. . . . . . . . . . . . . . . . . . . . . . . . . 35-2
Prestarting Checks
Service Daily Before Start-Up . . . . . . . . . . . . . . . 40-1
Operating the Engine
Before Starting the Engine . . . . . . . . . . . . . . . . .
Starting the Engine. . . . . . . . . . . . . . . . . . . . . . .
Check Instruments After Starting . . . . . . . . . . . .
Oil Pressure Indicator . . . . . . . . . . . . . . . . . . . . .
Charging System Indicator . . . . . . . . . . . . . . . . .
Air Restriction Sensor. . . . . . . . . . . . . . . . . . . . .
Air Restriction Sensor (5103E Tractor) . . . . . . . .
Coolant Temperature Gauge . . . . . . . . . . . . . . .
Watch Fuel Level . . . . . . . . . . . . . . . . . . . . . . . .
Watch Fuel Level (5103E Tractor) . . . . . . . . . . .
Changing Engine Speeds . . . . . . . . . . . . . . . . . .
Warming Up the Engine . . . . . . . . . . . . . . . . . . .
50-1
50-1
50-3
50-3
50-4
50-5
50-6
45-1
45-2
45-3
45-3
45-4
45-4
45-5
45-5
45-6
45-6
45-7
45-7
Drawbar and PTO
Observe Drawbar Load Limitations. . . . . . . . . . . 65-1
Stay Clear of Rotating Drivelines . . . . . . . . . . . . 65-1
Continued on next page
All information, illustrations and specifications in this manual are based on
the latest information available at the time of publication. The right is
reserved to make changes at any time without notice.
COPYRIGHT 2006
DEERE & COMPANY
Moline, Illinois
All rights reserved
A John Deere ILLUSTRUCTION Manual
Previous Editions
Copyright 2004
i
022607
PN=1
Contents
Page
Page
Attaching PTO-Driven Implement . . . . . . . . . . . . 65-2
Operating Tractor PTO . . . . . . . . . . . . . . . . . . . . 65-3
Adjusting PTO Clutch Operating Rod . . . . . . . . . 65-5
Ballast
Planning for Maximum Productivity. . . . . . . . . . .
Selecting Ballast Carefully . . . . . . . . . . . . . . . . .
Matching Ballast to Load Work . . . . . . . . . . . . . .
Measuring Wheel Slip—Manually . . . . . . . . . . . .
Ballast Limitations. . . . . . . . . . . . . . . . . . . . . . . .
Ballasting Front End for Transport . . . . . . . . . . .
Ballasting Front End for Transport (5103E
Tractor) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ballasting Tractor . . . . . . . . . . . . . . . . . . . . . . . .
Determining Maximum Rear Ballast . . . . . . . . . .
Determining Maximum Front Ballast . . . . . . . . . .
Using Cast Iron Weights. . . . . . . . . . . . . . . . . . .
Installing Rear Cast Iron Weights . . . . . . . . . . . .
Using Liquid Weight . . . . . . . . . . . . . . . . . . . . . .
Lubricant Storage . . . . . . . . . . . . . . . . . . . . . . . .
Diesel Engine Oil . . . . . . . . . . . . . . . . . . . . . . . .
Diesel Engine Coolant . . . . . . . . . . . . . . . . . . . .
Use Correct Transmission-Hydraulic Filter
Element . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmission and Hydraulic Oil . . . . . . . . . . . . .
Grease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70-1
70-1
70-1
70-2
70-3
70-3
Service—Every 10 Hours
Check Engine Oil Level . . . . . . . . . . . . . . . . . . .
Check Coolant Level . . . . . . . . . . . . . . . . . . . . .
Drain Water and Sediment From Fuel Filter . . . .
Lubricate as Necessary . . . . . . . . . . . . . . . . . . .
Wheels, Tyres and Treads
Service Tyres Safely . . . . . . . . . . . . . . . . . . . . . 75-1
Check Implement-to-Tyre Clearance . . . . . . . . . 75-1
Check Tyre Inflation Pressure . . . . . . . . . . . . . . 75-2
Tyre Inflation Pressure Chart . . . . . . . . . . . . . . . 75-3
Tighten Wheel/Axle Hardware Correctly . . . . . . . 75-3
Tighten Bolts— Front Axle . . . . . . . . . . . . . . . . . 75-3
Tighten Bolt Adjustable Front Axle––If
Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75-4
Tighten Bolts—Rear Axle (M-14 Bolts) . . . . . . . . 75-5
Tighten Bolts—Rear Axle (M-20 Stud) . . . . . . . . 75-6
Observe Rear Wheel Tread Width Limitations . . 75-6
Tread Settings—Multi-Position Rear Wheels . . . 75-7
Tread Settings—Adjustable Front Axle––If
Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75-8
Checking Toe-In . . . . . . . . . . . . . . . . . . . . . . . . . 75-9
Adjusting Toe-In . . . . . . . . . . . . . . . . . . . . . . . . 75-10
Adjusting Toe-In - Adjustable Front Axle––
IF Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 75-11
80-1
80-1
80-4
80-4
Fuels, Lubricants and Coolant
Handle Fuel Safely—Avoid Fires . . . . . . . . . . . .
Handle Fluids Safely—Avoid Fires . . . . . . . . . . .
Fuel Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diesel Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diesel Fuel Filters. . . . . . . . . . . . . . . . . . . . . . . .
Fill Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . .
85-1
85-1
85-2
85-2
85-2
85-3
85-6
85-6
85-7
Service and Maintenance
Observe Service Intervals. . . . . . . . . . . . . . . . . . 90-1
Break-In Service. . . . . . . . . . . . . . . . . . . . . . . . . 90-1
Service Intervals. . . . . . . . . . . . . . . . . . . . . . . . . 90-2
70-4
70-4
70-5
70-5
70-5
70-6
70-6
Transporting
Use Safety Lights and Devices. . . . . . . . . . . . . .
Driving Tractor on Roads . . . . . . . . . . . . . . . . . .
Transport on Carrier . . . . . . . . . . . . . . . . . . . . . .
Towing Tractor . . . . . . . . . . . . . . . . . . . . . . . . . .
85-4
85-4
85-5
95-1
95-1
95-2
95-2
Service—Every 50 Hours
Check Transmission-Hydraulic System
Oil Level . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clean and Check Battery . . . . . . . . . . . . . . . . .
Lubricate Front Axle Pivot Pin . . . . . . . . . . . . .
Lubricate Steering Spindles . . . . . . . . . . . . . . .
Lubricate Clutch Pedal and Brake Pedal . . . . .
Inspect Tyres and Loose Hardwares . . . . . . . .
100-1
100-1
100-2
100-2
100-3
100-4
Service—Every 250 Hours
Change Engine Oil and Filter . . . . . . . . . . . . . .
Service Air Cleaner . . . . . . . . . . . . . . . . . . . . .
Replace Fuel Filter Inserts . . . . . . . . . . . . . . . .
Inspect and Adjust Alternator/Fan Belt . . . . . . .
Lubricate 3-Point Hitch . . . . . . . . . . . . . . . . . . .
Check Neutral Start System . . . . . . . . . . . . . . .
Check and Adjust Clutch Pedal Free Play . . . .
Check and Adjust Brake Pedal Free Play. . . . .
110-1
110-1
110-2
110-2
110-3
110-3
110-4
110-5
Service—Every 500 Hours
Replace Transmission-Hydraulic Filter . . . . . . . 112-1
Service—Every 600 Hours
Clean Engine Crankcase Vent Tube. . . . . . . . .
Pack Front Wheel Bearings (Only For
Carraro Front Axle) . . . . . . . . . . . . . . . . . . . .
Check Hoses and Hose Clamps for
Tightness . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lubricate Rear Axle Bearings . . . . . . . . . . . . . .
Check Engine Idle Speeds . . . . . . . . . . . . . . . .
Check Front Axle Pivot Pin. . . . . . . . . . . . . . . .
Adjust Engine Valve Clearance . . . . . . . . . . . .
115-1
115-1
115-2
115-3
115-4
115-4
115-5
Continued on next page
ii
022607
PN=2
Contents
Page
Page
Service—Every 1250 Hours
Change Transmission-Hydraulic Oil and
Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120-1
Clean Transmission-Hydraulic Pickup
Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120-2
Connecting Alternator Wiring For (5103E) . . .
Connecting Alternator Wiring For (5103,
5103S, 5203) . . . . . . . . . . . . . . . . . . . . . . .
Locating Fusible Link . . . . . . . . . . . . . . . . . . .
Locating Fuses . . . . . . . . . . . . . . . . . . . . . . . .
Fuse Size and Function . . . . . . . . . . . . . . . . .
Fuse Size and Function (5103E Tractor) . . . .
Aiming Headlights. . . . . . . . . . . . . . . . . . . . . .
Adjusting Headlights . . . . . . . . . . . . . . . . . . . .
Replace Headlight Bulb . . . . . . . . . . . . . . . . .
Replace Tail Light and Warning Light
Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replace Flood Lamp Bulb . . . . . . . . . . . . . . .
Checking Tyres . . . . . . . . . . . . . . . . . . . . . . .
Service—Annually
Replace Air Cleaner Elements . . . . . . . . . . . . . 125-1
Service—2 Years/2000 Hours
Flush Cooling System. . . . . . . . . . . . . . . . . . . . 130-1
Service—As Required
Service Air Cleaner . . . . . . . . . . . . . . . . . . . . . 135-1
Adjust Throttle Friction . . . . . . . . . . . . . . . . . . . 135-1
140-21
140-22
140-22
140-23
140-24
140-25
140-26
140-27
140-28
140-29
140-29
140-30
Troubleshooting
Engine Troubleshooting . . . . . . . . . . . . . . . . . .
Transmission Troubleshooting . . . . . . . . . . . . .
Hydraulic System Troubleshooting . . . . . . . . . .
Brakes Troubleshooting . . . . . . . . . . . . . . . . . .
Rockshaft and 3-Point Hitch
Troubleshooting . . . . . . . . . . . . . . . . . . . . . .
Electrical System Troubleshooting . . . . . . . . . .
Service
Additional Service Information . . . . . . . . . . . . . 140-1
Service Tractor Safely . . . . . . . . . . . . . . . . . . . 140-2
Engine Break-In Oil . . . . . . . . . . . . . . . . . . . . . 140-3
Work In Ventilated Area . . . . . . . . . . . . . . . . . . 140-3
Using High-Pressure Washers . . . . . . . . . . . . . 140-3
Opening Hood . . . . . . . . . . . . . . . . . . . . . . . . . 140-4
Removing Side Screens . . . . . . . . . . . . . . . . . . 140-4
Removing Hood . . . . . . . . . . . . . . . . . . . . . . . . 140-5
Air Intake System Components . . . . . . . . . . . . 140-5
Service Air Cleaner at Regular Intervals . . . . . . 140-6
Service Air Cleaner at Regular Intervals
(5103E Tractor). . . . . . . . . . . . . . . . . . . . . . . 140-6
Checking Air Intake System . . . . . . . . . . . . . . . 140-7
Removing Primary Air Cleaner Element . . . . . . 140-8
Cleaning Primary Element . . . . . . . . . . . . . . . . 140-8
Washing Primary Element . . . . . . . . . . . . . . . . 140-9
Inspecting Element . . . . . . . . . . . . . . . . . . . . . . 140-9
Storing Element . . . . . . . . . . . . . . . . . . . . . . . 140-10
Replacing Alternator/Fan Belt . . . . . . . . . . . . . 140-10
Fuel System Components . . . . . . . . . . . . . . . 140-11
Do Not Modify Fuel System . . . . . . . . . . . . . . 140-11
Bleeding Fuel System. . . . . . . . . . . . . . . . . . . 140-12
Bleed Fuel System At Fuel Injection
Nozzles. . . . . . . . . . . . . . . . . . . . . . . . . . . . 140-12
Engine Cooling System . . . . . . . . . . . . . . . . . 140-13
Cleaning Grille, Screens, Radiator and
Oil Cooler . . . . . . . . . . . . . . . . . . . . . . . . . . 140-14
Prevent Battery Explosions. . . . . . . . . . . . . . . 140-14
Observe Electrical Service Precautions . . . . . 140-15
Battery Access . . . . . . . . . . . . . . . . . . . . . . . . 140-15
Removing Battery . . . . . . . . . . . . . . . . . . . . . . 140-16
Checking Battery Condition . . . . . . . . . . . . . . 140-17
Servicing Battery . . . . . . . . . . . . . . . . . . . . . . 140-18
Charging Battery . . . . . . . . . . . . . . . . . . . . . . 140-20
Battery Replacement Specifications . . . . . . . . 140-20
Connecting Starter Wiring. . . . . . . . . . . . . . . . 140-21
145-1
145-4
145-5
145-5
145-6
145-8
Tractor Storage
Storing Tractor . . . . . . . . . . . . . . . . . . . . . . . . . 150-1
Removing Tractor From Storage . . . . . . . . . . . 150-4
Specifications
John Deere 5103E Tractor . . . . . . . . . . . . . . . .
John Deere 5103 Tractor . . . . . . . . . . . . . . . . .
John Deere 5103S Tractor . . . . . . . . . . . . . . . .
John Deere 5203 Tractor . . . . . . . . . . . . . . . . .
John Deere 5104 Tractor . . . . . . . . . . . . . . . . .
John Deere 5204 Tractor . . . . . . . . . . . . . . . . .
Ground Speed at Rated Engine Speed
(2300 rpm) . . . . . . . . . . . . . . . . . . . . . . . . . .
Metric Bolt and Cap Screw Torque Values . . . .
Unified Inch Bolt and Cap Screw Torque
Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Identification Numbers
Identification Plates . . . . . . . . . . . . . . . . . . . . .
Record Tractor Serial (Chassis) Number . . . . .
Record Front Axle Serial Number . . . . . . . . . . .
Record Engine Serial Number . . . . . . . . . . . . .
Record Transmission Serial Number . . . . . . . .
155-1
155-2
155-3
155-4
155-5
155-6
155-7
155-8
155-9
160-1
160-1
160-2
160-2
160-3
Lubrication Maintenance Record Charts
50, 250 Hour Service Chart . . . . . . . . . . . . . . . 165-1
500,600 Hour Service Chart . . . . . . . . . . . . . . . 165-2
Continued on next page
iii
022607
PN=3
Contents
Page
1000, 1250 Hour Service Chart . . . . . . . . . . . .
Annual Service Chart . . . . . . . . . . . . . . . . . . .
2000 Hour Service Chart . . . . . . . . . . . . . . . . .
As Required Service Chart . . . . . . . . . . . . . . . .
165-3
165-4
165-5
165-6
John Deere Service
John Deere Parts . . . . . . . . . . . . . . . . . . . . . . .
The Right Tools . . . . . . . . . . . . . . . . . . . . . . . .
Well Trained Technician . . . . . . . . . . . . . . . . . .
Prompt Service. . . . . . . . . . . . . . . . . . . . . . . . .
170-1
170-1
170-1
170-1
iv
022607
PN=4
Safety
Recognize Safety Information
–UN–07DEC88
This is a safety-alert symbol. When you see this symbol
on your machine or in this manual, be alert to the
potential for personal injury.
T81389
Follow recommended precautions and safe operating
practices.
DX,ALERT –19–29SEP98–1/1
Understand Signal Words
TS187
DANGER or WARNING safety signs are located near
specific hazards. General precautions are listed on
CAUTION safety signs. CAUTION also calls attention to
safety messages in this manual.
–19–30SEP88
A signal word—DANGER, WARNING, or CAUTION—is
used with the safety-alert symbol. DANGER identifies the
most serious hazards.
DX,SIGNAL –19–03MAR93–1/1
Carefully read all safety messages in this manual and on
your machine safety signs. Keep safety signs in good
condition. Replace missing or damaged safety signs. Be
sure new equipment components and repair parts include
the current safety signs. Replacement safety signs are
available from your John Deere dealer.
TS201
Learn how to operate the machine and how to use
controls properly. Do not let anyone operate without
instruction.
–UN–23AUG88
Follow Safety Instructions
Keep your machine in proper working condition.
Unauthorized modifications to the machine may impair the
function and/or safety and affect machine life.
If you do not understand any part of this manual and need
assistance, contact your John Deere dealer.
DX,READ –19–03MAR93–1/1
05-1
022607
PN=7
Safety
Prevent Machine Runaway
Avoid possible injury or death from machinery runaway.
–UN–11JAN89
Do not start engine by shorting across starter terminals.
Machine will start in gear if normal circuitry is bypassed.
TS177
NEVER start engine while standing on ground. Start
engine only from operator’s seat, with transmission in
neutral.
CED,OUO1032,2778 –19–15OCT99–1/1
Operate Tractor Safely
Features designed into your tractor make operation safer
and let it perform a wide variety of jobs. Use your tractor
only for specified jobs it was designed to perform:
implement carrier, load mover, remote power source, or
transport unit—not a recreational vehicle.
Tractor upsets
Improper starting procedures
Crushing and pinching during hitching
Collisions with other motor vehicles
Getting entangled in PTO shafts
Falls from tractors
M47224A
•
•
•
•
•
•
–19–02JUN97
Careless use or misuse can result in unnecessary
accidents. Be alert to hazards of tractor operation.
Understand causes of accidents and take every
precaution to avoid them. Most common accidents are
caused from:
TS276
• Put transmission in neutral (N) and set brakes before
dismounting. Leaving transmission in gear with engine
stopped will NOT prevent the tractor from moving.
• Be sure everyone is clear of tractor and attached
equipment before starting engine.
• Never try to get on or off a moving tractor.
• When tractor is left unattended, place in neutral (N), set
brakes, lower implements to the ground, stop the
engine, and remove the key.
–UN–23AUG88
Avoid accidents by taking the following precautions:
AG,OUO6035,84 –19–18MAY00–1/1
05-2
022607
PN=8
Safety
Use Caution on Hillsides
Avoid holes, ditches, and obstructions which cause the
tractor to tip, especially on hillsides. Avoid sharp, uphill
turns.
Never drive near the edge of a gully or steep
embankment -- it might cave in.
Driving forward out of a ditch or mired condition or up a
steep slope could cause tractor to tip over rearward. Back
out of these situations if possible.
Danger of overturn increases greatly with narrow tread
setting, at high speed.
Hitch towed loads only to drawbar. When using a chain,
take up the slack slowly.
AG,OUO6035,65 –19–17MAY00–1/1
When driving on icy, wet or graveled surfaces, reduce
speed and be sure tractor is properly ballasted to avoid
skidding and loss of steering control.
LV4042
Shift to a low gear before descending a steep hill to
improve your control of the tractor with little or no braking.
Use engine braking to reduce speed before applying
tractor brakes. Run-away tractors often tip over. Never
coast downhill.
–UN–09JUL99
Shift to Low Gear on Hills
Additional ballast may be needed for transporting heavy
hitch mounted implements. When implement is raised,
drive slowly over rough ground, regardless of how much
ballast is used.
AG,OUO6035,83 –19–17MAY00–1/1
05-3
022607
PN=9
Safety
Avoid Tipping
Do not drive where machine could slip or tip.
Reduce speed and exercise extreme caution on slopes
and in sharp turns to prevent tipping or loss of control.
Be especially cautious when changing direction on
slopes.
Stay alert for holes, rocks, and roots in the terrain, and
other hidden hazards. Keep away from drop-offs.
Slow down before you make a sharp turn.
Do not stop or start suddenly when going uphill or
downhill.
Use care when pulling loads or using heavy
equipment:
If machine stops going up hill:
• Use only approved drawbar hitch points.
• Limit loads to those you can safely control.
• Use counterweights or wheel weights when
suggested in this operator’s manual.
• STOP the PTO.
• Back down slowly.
MX,AVOIDTIP1A1 –19–22JUL94–1/1
Back your tractor out if it gets mired down in mud. Unhitch
any towed implements. Dig mud from behind the rear
wheels. Place boards behind the wheels to provide a solid
base and try to back out slowly. If necessary, dig mud
from the front of all wheels and drive slowly ahead.
TS1645
Attempting to free a mired machine can involve safety
hazards such as the mired tractor tipping rearward, the
towing tractor overturning, and the tow chain or tow bar (a
cable is not recommended) failing and recoiling from its
stretched condition.
–UN–15SEP95
Freeing a Mired Machine
TS263
Always hitch to the drawbar of the towing unit. Do not
hitch to the front pushbar attachment point. Before
moving, clear the area of people. Apply power smoothly to
take up the slack: a sudden pull could snap any towing
device causing it to whip or recoil dangerously.
–UN–23AUG88
If necessary to tow with another unit, use a tow bar or a
long chain (a cable is not recommended). Inspect the
chain for flaws. Make sure all parts of towing devices are
of adequate size and strong enough to handle the load.
DX,MIRED –19–07JUL99–1/1
05-4
022607
PN=10
Safety
Park Tractor Safely
To park tractor safely:
–UN–26APR89
Disengage PTO.
Lower equipment to the ground.
Put gear shift lever in NEUTRAL.
Set brakes.
STOP the engine.
Remove key.
Before you leave the operator’s seat, wait for engine and
attachment parts to stop moving.
M35691
•
•
•
•
•
•
MX,SAIP,AAA1 –19–21AUG99–1/1
Keep Riders Off Machine
TS290
Riders on machine are subject to injury such as being
struck by foreign objects and being thrown off of the
machine. Riders also obstruct the operator’s view resulting
in the machine being operated in an unsafe manner.
–UN–23AUG88
Only allow the operator on the machine. Keep riders off.
DX,RIDER –19–03MAR93–1/1
Handle Fuel Safely—Avoid Fires
Prevent fires by keeping machine clean of accumulated
trash, grease, and debris. Always clean up spilled fuel.
TS202
Always stop engine before refueling machine. Fill fuel tank
outdoors.
–UN–23AUG88
Handle fuel with care: it is highly flammable. Do not refuel
the machine while smoking or when near open flame or
sparks.
DX,FIRE1 –19–03MAR93–1/1
05-5
022607
PN=11
Safety
Prepare for Emergencies
Be prepared if a fire starts.
TS291
Keep emergency numbers for doctors, ambulance service,
hospital, and fire department near your telephone.
–UN–23AUG88
Keep a first aid kit and fire extinguisher handy.
DX,FIRE2 –19–03MAR93–1/1
Wear Protective Clothing
Wear a suitable hearing protective device such as
earmuffs or earplugs to protect against objectionable or
uncomfortable loud noises.
TS206
Prolonged exposure to loud noise can cause impairment
or loss of hearing.
–UN–23AUG88
Wear close fitting clothing and safety equipment
appropriate to the job.
Operating equipment safely requires the full attention of
the operator. Do not wear radio or music headphones
while operating machine.
DX,WEAR –19–10SEP90–1/1
Protect Against Noise
TS207
Wear a suitable hearing protective device such as
earmuffs or earplugs to protect against objectionable or
uncomfortable loud noises.
–UN–23AUG88
Prolonged exposure to loud noise can cause impairment
or loss of hearing.
DX,NOISE –19–03MAR93–1/1
05-6
022607
PN=12
Safety
Stay Clear of Rotating Drivelines
Wear close fitting clothing. Stop the engine and be sure
PTO driveline is stopped before making adjustments,
connections, or cleaning out PTO driven equipment.
TS1644
Keep tractor master shield and driveline shields in place
at all times. Make sure rotating shields turn freely.
–UN–22AUG95
Entanglement in rotating driveline can cause serious injury
or death.
DX,PTO –19–12SEP95–1/1
Use Safety Lights and Devices
TS951
Use headlights, flashing warning lights, and turn signals
day and night. Follow local regulations for equipment
lighting and marking. Keep lighting and marking visible,
clean, and in good working order. Replace or repair
lighting and marking that has been damaged or lost. An
implement safety lighting kit is available from your John
Deere dealer.
–UN–12APR90
Prevent collisions between other road users, slow moving
tractors with attachments or towed equipment, and
self-propelled machines on public roads. Frequently check
for traffic from the rear, especially in turns, and use turn
signal lights.
DX,FLASH –19–07JUL99–1/1
Safely Transporting the Tractor
LV610
Never tow a tractor at a speed greater than 16 km/h (10
mph). An operator must steer and brake the tractor under
tow.
–UN–22APR94
A disabled tractor is best transported on a flatbed carrier.
Use chains to secure the tractor to the carrier.
MX,SAIP,LA1 –19–29JUL94–1/1
05-7
022607
PN=13
Safety
Observe these recommended maximum road speeds, or
local speed limits which may be lower:
• If towed equipment does not have brakes, do not travel
more than 32 km/h (20 mph) and do not tow loads more
than 1.5 times the tractor weight.
• If towed equipment has brakes, do not travel more than
40 km/h (25 mph) and do not tow loads more than 4.5
times the tractor weight.
TS216
Stopping distance increases with speed and weight of
towed loads, and on slopes. Towed loads with or without
brakes that are too heavy for the tractor or are towed too
fast can cause loss of control. Consider the total weight of
the equipment and its load.
–UN–23AUG88
Tow Loads Safely
Ensure the load does not exceed the recommended
weight ratio. Add ballast to recommended maximum for
tractor, lighten the load, or get a heavier towing unit. The
tractor must be heavy and powerful enough with adequate
braking power for the towed load. Use additional caution
when towing loads under adverse surface conditions,
when turning, and on inclines.
DX,TOW –19–02OCT95–1/1
05-8
022607
PN=14
Safety
Practice Safe Maintenance
Understand service procedure before doing work. Keep
area clean and dry.
Never lubricate, service, or adjust machine while it is
moving. Keep hands, feet , and clothing from
power-driven parts. Disengage all power and operate
controls to relieve pressure. Lower equipment to the
ground. Stop the engine. Remove the key. Allow machine
to cool.
Securely support any machine elements that must be
raised for service work.
On towed implements, disconnect wiring harnesses from
tractor before servicing electrical system components or
welding on machine.
TS218
On self-propelled equipment, disconnect battery ground
cable (-) before making adjustments on electrical systems
or welding on machine.
–UN–23AUG88
Keep all parts in good condition and properly installed. Fix
damage immediately. Replace worn or broken parts.
Remove any buildup of grease, oil, or debris.
DX,SERV –19–17FEB99–1/1
Service Tractor Safely
LV828
Tighten wheel hardware to correct torque as specified in
Wheels, Tyress and Tread section. Torque at intervals
shown in Break-In Period and Lubrication and
Maintenance sections, to ensure that wheel hardware
does not loosen.
–UN–08AUG94
Do not service the tractor while it is in motion or while the
engine is running.
Reinstall shields removed during service.
AG,OUO6035,70 –19–17MAY00–1/1
05-9
022607
PN=15
Safety
Do not support the machine on cinder blocks, hollow tiles,
or props that may crumble under continuous load. Do not
work under a machine that is supported solely by a jack.
Follow recommended procedures in this manual.
TS229
Always lower the attachment or implement to the ground
before you work on the machine. If the work requires that
the machine or attachment be lifted, provide secure
support for them. If left in a raised position, hydraulically
supported devices can settle or leak down.
–UN–23AUG88
Support Machine Properly
When implements or attachments are used with a
machine, always follow safety precautions listed in the
implement or attachment operator’s manual.
DX,LOWER –19–24FEB00–1/1
TS953
Flammable spray can be generated by heating near
pressurized fluid lines, resulting in severe burns to
yourself and bystanders. Do not heat by welding,
soldering, or using a torch near pressurized fluid lines or
other flammable materials. Pressurized lines can
accidentally burst when heat goes beyond the immediate
flame area.
–UN–15MAY90
Avoid Heating Near Pressurized Fluid Lines
DX,TORCH –19–10DEC04–1/1
05-10
022607
PN=16
Safety
Avoid High-Pressure Fluids
Search for leaks with a piece of cardboard. Protect hands
and body from high pressure fluids.
X9811
Avoid the hazard by relieving pressure before
disconnecting hydraulic or other lines. Tighten all
connections before applying pressure.
–UN–23AUG88
Escaping fluid under pressure can penetrate the skin
causing serious injury.
If an accident occurs, see a doctor immediately. Any fluid
injected into the skin must be surgically removed within a
few hours or gangrene may result. Doctors unfamiliar with
this type of injury should reference a knowledgeable
medical source. Such information is available from Deere
& Company Medical Department in Moline, Illinois, U.S.A.
DX,FLUID –19–03MAR93–1/1
Service Cooling System Safely
TS281
If radiator cap must be removed, do not remove when
engine is hot. Shut engine off and wait until cap is cool
enough to touch with bare hands. Slowly loosen cap to
first stop to relieve pressure before removing completely.
–UN–23AUG88
Explosive release of fluids from pressurized cooling
system can cause serious burns.
AG,OUO1032,2682 –19–30SEP99–1/1
Store Attachments Safely
TS219
Securely store attachments and implements to prevent
falling. Keep playing children and bystanders away from
storage area.
–UN–23AUG88
Stored attachments such as dual wheels, cage wheels,
and loaders can fall and cause serious injury or death.
DX,STORE –19–03MAR93–1/1
05-11
022607
PN=17
Safety
Prevent Acid Burns
Sulfuric acid in battery electrolyte is poisonous. It is strong
enough to burn skin, eat holes in clothing, and cause
blindness if splashed into eyes.
Avoid the hazard by:
1.
2.
3.
4.
5.
Filling batteries in a well-ventilated area.
Wearing eye protection and rubber gloves.
Avoiding breathing fumes when electrolyte is added.
Avoiding spilling or dripping electrolyte.
Use proper jump start procedure.
If you spill acid on yourself:
–UN–23AUG88
1. Flush your skin with water.
2. Apply baking soda or lime to help neutralize the acid.
3. Flush your eyes with water for 15—30 minutes. Get
medical attention immediately.
If acid is swallowed:
TS203
1. Do not induce vomiting.
2. Drink large amounts of water or milk, but do not
exceed 2 L (2 quarts).
3. Get medical attention immediately.
DX,POISON –19–21APR93–1/1
05-12
022607
PN=18
Safety
Service Tires Safely
Explosive separation of a tire and rim parts can cause
serious injury or death.
Do not attempt to mount a tire unless you have the proper
equipment and experience to perform the job.
Always maintain the correct tire pressure. Do not inflate
the tires above the recommended pressure. Never weld or
heat a wheel and tire assembly. The heat can cause an
increase in air pressure resulting in a tire explosion.
Welding can structurally weaken or deform the wheel.
TS211
Check wheels for low pressure, cuts, bubbles, damaged
rims or missing lug bolts and nuts.
–UN–23AUG88
When inflating tires, use a clip-on chuck and extension
hose long enough to allow you to stand to one side and
NOT in front of or over the tire assembly. Use a safety
cage if available.
DX,RIM –19–24AUG90–1/1
Dispose of Waste Properly
Do not pour waste onto the ground, down a drain, or into
any water source.
TS1133
Use leakproof containers when draining fluids. Do not use
food or beverage containers that may mislead someone
into drinking from them.
–UN–26NOV90
Improperly disposing of waste can threaten the
environment and ecology. Potentially harmful waste used
with John Deere equipment include such items as oil, fuel,
coolant, brake fluid, filters, and batteries.
Inquire on the proper way to recycle or dispose of waste
from your local environmental or recycling center, or from
your John Deere dealer.
AG,OUO1032,2683 –19–30SEP99–1/1
05-13
022607
PN=19
Safety Signs
Warning Labels
Keep warning labels in good condition, replace if not in
readable condition.
PY4880
LV4307
–UN–06DEC05
–19–04NOV05
LV1932
PY5801
–19–02JUN97
–UN–11JUL06
PY5798
M71026
–19–02JUL90
–UN–11JUL06
PY80265,05GO801 –19–12JUN06–1/3
Continued on next page
10-1
PY80265,05GO801 –19–12JUN06–2/3
022607
PN=20
PY4141
–UN–26AUG04
–UN–26AUG04
PY4140
PY5353
PY1089
–UN–06DEC05
–UN–16JUL01
PY1667
PY4879
–UN–06DEC05
–UN–06DEC05
Safety Signs
PY80265,05GO801 –19–12JUN06–3/3
10-2
PN=21
022607
Controls and Instruments
PY6079
–UN–06AUG06
Tractor Controls
A—Steering Wheel
B—Hand Throttle
C—Horn
D—Light Switch
E—Hazard Switch
F—Turn Signal Switch
G—Clutch Pedal
H—Key Switch
I—Hand Brake Lever
Continued on next page
15-1
J—Foot Throttle
K—Brake Pedals
NR25796,0000345 –19–10AUG06–1/2
022607
PN=22
–UN–11JUL06
PY4947
–UN–19MAY05
PY6081
–UN–06AUG06
PY4127
PY6080
–UN–26AUG04
–UN–06AUG06
Controls and Instruments
PY5908
A—Gear Shift Lever
B—Rockshaft Draft Control Lever
C—Rockshaft Position Control Lever
D—PTO Lever
E—Range Shift Lever
F—Differential Lock
G—Rate of Drop of Knob
NR25796,0000345 –19–10AUG06–2/2
15-2
022607
PN=23
Controls and Instruments
PY5750
–UN–01JUN06
Instrument Panel
For 5103, 5103S, 5203, 5104 and 5204 Tractor
A—Air Restriction Indicator
B—High Beam Indicator
C—Hour Meter
D—Charging System Indicator
E—Engine Oil Pressure
Indicator
F—Coolant Temperature
Gauge
G—Turn Signal Direction
Indicators
H—Tachometer
I—Fuel Gauge
PY80265,05GO804 –19–29DEC06–1/1
PY5751
–UN–08JUN06
Instrument Panel (5103E Tractor)
For 5103E Tractor
A—Hour Meter
B—Charging System Indicator
C—High Beam Indicator
D—Engine Oil Pressure
Indicator
E—Coolant Temperature
Gauge
F—Turn Signal Direction
Indicators
G—Tachometer
PY80265,05GO805 –19–08JUN06–1/1
15-3
022607
PN=24
Lights
Light Switch Positions
Tractor light switch has five positions:
–UN–23FEB06
A—Turns off all lights.
B—Turns on warning lights only. Use for parking the
vehicle
PY4106
C—Turns on dim headlights,tail lights, and warning
lights.Turn switch to this position before meeting other
vehicles.
D—Turns on bright headlights, tail lights, and warning
lights. For highway driving during night time
E—Turns on high beamlight.
PY4107
–UN–21AUG04
F— Switch on flood lamp (plough lamp). For field use
only. Do not use on roads. Flood light might blind or
confuse other drivers
A—Lights Off
B—Warning Lights Position
C—Dim Headlights, Tail Lights, and Warning Light
Position
D—Bright Headlights, Tail Lights and Warning Lights
Position
E—High Beamlight
F—Flood Light Switch
PY80265,05GO806 –19–03JUL06–1/1
20-1
022607
PN=25
Lights
Using Headlights
–UN–23FEB06
Dual-beam headlights (F) are switched on by either “High
Beamlight” (E), “Bright Headlight” (D), or “Dim Headlight”
(C) light switch positions.
Always dim lights before meeting another vehicle.
PY4106
Keep headlights adjusted properly, (see Adjusting
Headlights in Service section).
PY5148
–UN–23FEB06
A—Lights Off
B—Warning Lights Position
C—Dim Headlights, Tail Lights, and Warning Light
Position
D—Bright Headlights, Tail Lights and Warning Lights
Position
E—High Beamlight
F— Headlights
PY80265,05GO807 –19–10SEP05–1/1
Using High Beam Indicator
–UN–02JUN06
High beam indicator (A) should glow when light switch is
turned to “Bright Headlight” position or “Flood Light”
position. Bright headlights, tail lights, flood light and
warning lights should be on.
PY5726
A—High Beam Indicator
PY5752
–UN–01JUN06
For 5103, 5103S, 5203, 5104 and 5204 Tractor
For 5103E Tractor
PY80265,05GO808 –19–29DEC06–1/1
20-2
022607
PN=26
Lights
Using Tail Lights
Red tail lights (F) are switched on by either bright
headlight or dim headlight light switch position.
–UN–09JAN06
Be sure tail light lenses are clean before driving on a
road, so other drivers can see it easily.
PY5005
CAUTION: Prevent collisions between other
road users, slow moving tractors with
attachments or towed equipment, and
self-propelled machines on public roads.
Frequently check for traffic from the rear,
especially in turns, and use hand signals or
turn signal lights.
For 5103, 5103S, 5203, 5104 and 5204 Tractor
PY5007
–UN–09JUN06
Use headlights, flashing warning lights, and
turn signals day and night. Follow local
regulations for equipment lighting and marking.
Keep lighting and marking visible and in good
working order. Replace or repair lighting and
marking that has been damaged or lost. An
implement safety lighting kit is available from
your John Deere dealer.
For 5103E Tractor
PY4128
–UN–26AUG04
F— Tail Lights
G—Turn Signal Lights
H—Reflex Reflector
I—Flood Light Switch
PY80265,05GO809 –19–29DEC06–1/1
20-3
022607
PN=27
Lights
PY5008
–UN–23FEB06
–UN–09JUN06
Using Turn Signals
PY5006
PY5727
–UN–09JUN06
–UN–02JUN06
PY4114
For 5103, 5103S, 5203, 5104 and 5204 Tractor
For 5103, 5103S, 5203, 5104 and 5204 Tractor
For 5103E Tractor
Move turn signal lever (A) down to indicate left-hand turn
or up for right-hand turn. Indicator lights (D) will flash to
signal turn direction.
PY5753
–UN–01JUN06
When lever is up, front and rear facing lights on right-hand
side (C) will flash while left-hand lights (B) glow steady.
Left-hand lights (B) flash and right-hand lights (C) glow
steady when lever is down.
NOTE: Be sure to manually return lever to center position
after turning.
5103E Tractor
A—Turn Signal Lever
B—Left-Hand Lights
C—Right-Hand Lights
D—Dash Indicator Lights
PY80265,05GO810 –19–29DEC06–1/1
20-4
022607
PN=28
Lights
PY5010
PY5009
–UN–09JUN06
–UN–09JUN06
Using Hazard Lights
For 5103, 5103S, 5203, 5104 and 5204 Tractor
PY5011
PY5012
–UN–13JUN06
–UN–09JUN06
For 5103, 5103S, 5203, 5104 and 5204 Tractor
For 5103E Tractor
For 5103E Tractor
–UN–16FEB06
All 4 turn signal lights ( 2 front and 2 rear) start to blink
when hazard light switch (C) is pushed out. Use hazard
lights to warn incoming vehicles when tractor is stopped
on the road
PY1072
A—Turn Signal Light on Rear Side
B— Turn Signal Light on Front Side
C— Hazard Light Switch
PY80265,05GO811 –19–29DEC06–1/1
20-5
022607
PN=29
Lights
Using Flood Lamp
PY4150
–UN–20FEB06
A—Lights Off
B—Warning Lights Position
C—Dim Headlights, Tail Lights and Warning Light
Position
D—Bright Headlights, Tail Lights and Warning Lights
Position
E—High Beamlight
F—Horn
G—Flood Lamp
H—Flood Light switch
PY5365
CAUTION: When operating on a road, move
light switch to either “Bright or Dim Head
Lamp” positions Never use flood lamp when
transporting. A clear, bright light at the rear of
the tractor could confuse drivers of other
vehicles as they approach from the rear.
–UN–20FEB06
Flood lamp (G) is switched on by flood light switch (H).
PY80265,05GO812 –19–04JUL06–1/1
Seven-Terminal Outlet
–UN–09DEC05
Outlet (A) is used to connect lights, turn signals and
remote electrical equipment on trailers or implements.
Always use auxiliary light on towed implement when
tractor rear signals and other lights are obscured.
Wire Color
1
Ground
Black
2
Flood Lamp
Purple
3
Left Turn
Dark Green
4
Accessory
Red
5
Right Turn
Dark Green
6
Tail Lamp
Gray
7
Accessory
Red
–UN–11JUL06
Function
PY5526
Terminal
PY4132
NOTE: Matching plug is available through your John
Deere dealer.
A—Seven-Terminal Outlet
PY80265,05GO813 –19–11JUL06–1/1
20-6
022607
PN=30
Operator’s Platform
PY1047
PY4126
–UN–25JUN01
–UN–25AUG04
Selecting Seat Position
A—Cap Screws
Standard Seat
Loosen two cap screws (A) and move seat forward or
backward depending on operator’s requirement. After
getting right position, tighten both cap screws.
PY80265,05GO814 –19–10SEP05–1/2
Delux Seat
–UN–24JUN01
Seat can be moved forward or backward depending on
operator’s requirement. To move seat on either side, just
lift lever (A) and push the seat.
PY1032
A—Seat Adjustment Lever
PY80265,05GO814 –19–10SEP05–2/2
Adjusting Ride Comfort
Adjustment knob is located behind seat.
–UN–24JUN01
Weight markings are given on the rear of seat.Turn
adjustment knob (A) for a firm or soft ride. Seat
suspension will function properly relative to operator’s
weight.
PY1033
A—Weight Adjustment Knob
PY80265,05GO815 –19–10SEP05–1/1
25-1
022607
PN=31
Break-In Period
Observe Engine Operation Closely
–UN–31MAY06
IMPORTANT: The engine is ready for normal
operation. Be extra cautious during the
first 100 hours, until you become
thoroughly familiar with the sound and
feel of your new tractor. Stay extra
attentive and alert.
PY5728
Warm up tractor carefully. Check charging (A) and oil
pressure (B) warning indicator lights and coolant
temperature gauge (C).
For 5103, 5103S, 5203, 5104 and 5204 Tractor
Avoid unnecessary engine idling.
Check engine oil, coolant and transmission/hydraulic fluid
levels frequently. Watch for fluid leaks.
PY5754
A—Charging Indicator
B—Oil Pressure Indicator
C—Coolant Temperature Indicator
–UN–01JUN06
NOTE: If engine oil must be added, use seasonal
viscosity grade oil. Use only lubricants meeting
specifications given in the Fuels, Lubricants and
Coolant section.
For 5103E Tractor
PY80265,05GO816 –19–29DEC06–1/1
35-1
022607
PN=32
Break-In Period
Break-In Service
IMPORTANT: Keep wheel hardware tight to avoid
tractor damage. Check wheel
hardware torque before operating,
twice during first ten hours of
operation, after fifty hours of
operation, and periodically
thereafter.
After the First 50 Hours of Operation:
During the First 10 Hours of Operation:
Perform 50 Hours Service
Perform daily or 10 hours service. (See Service
Intervals in Lubrication and Maintenance section)
After the First 100 Hours of Operation:
Tighten wheel hardware. (See Wheels, tyres, and
Treads section)
Check alternator/fan belt tension and tighten air intake
and cooling system hose clamps
Replace transmission-hydraulic filter element
Tighten wheel hardware. (See Wheels, tyres, and
Treads section)
Change engine oil and filter1
1
See Engine Break-In Oil in Service section for additional
information.
PY80265,05GO817 –19–10SEP05–1/1
35-2
022607
PN=33
Prestarting Checks
Service Daily Before Start-Up
CAUTION: DO NOT remove radiator cap or drain
coolant until coolant is cold. Always loosen
radiator cap slowly to relieve any excess
pressure.
3. Check coolant level in recovery tank (D). If engine is
COOL and level is below “LOW” mark, add coolant to
recovery tank to bring level to “LOW” mark.
NOTE: Coolant level with a cold engine should be at the
“LOW” mark. A tractor at operating temperature
should have a coolant level at the “FULL” mark.
FD000047
2. Drain water and sediment from fuel filter drain (C).
(See Drain Water and Sediment from Fuel Filter in
Service—10 Hours.
–UN–13MAR96
PY5366
Safe operating range is between two marks on
dipstick. Do not operate engine when oil level is below
lower mark on dipstick. Add seasonal viscosity grade
oil through filler hole (A). (See Fuel, Lubricants, and
Coolant section for oil specifications.)
–UN–09DEC05
1. Check the engine oil level. Wipe dipstick (B) off and
reinsert it fully. Remove and locate oil level.
Use multipurpose grease. For detailed information see
Lubrication and Maintenance section.
PY5370
–UN–09DEC05
A—Engine Oil Filler Cap
B—Engine Oil Dipstick
C—Fuel Filter Drain
D—Recovery Tank
E—Radiator Cap
PY5369
• Front axle pivot pin(s)
• Steering spindles
• Tie rod ends
–UN–09DEC05
4. Lubricate the following items at 10 hour intervals if
operating in extremely wet or muddy conditions.
PY80265,05GO818 –19–11JUL06–1/1
40-1
022607
PN=34
Operating the Engine
PY4108
TS220
–UN–21AUG04
–UN–23AUG88
Before Starting the Engine
CAUTION: Prevent asphyxiation. Engine
exhaust fumes can cause sickness or death to
you or someone else.
Single Clutch Tractor
If you must operate engine in a building, be
positive there is adequate ventilation. Either use
an exhaust pipe extension to remove the
exhaust fumes or open doors and windows to
bring enough outside air into the area.
–UN–27MAY05
1. Check fuel gauge to be sure tractor has plenty of fuel.
PY4953
2. Place range shift lever (A) in neutral (N) position.
Starter will not operate if range shift lever is not in this
position.
3. Place rockshaft control levers (C and D) in lowered
position.
Dual Clutch Tractor
4. Check indicator lights. Indicators should illuminate
when key switch is turned to the “ON” position.
–UN–22APR05
If any indicator does not function properly, see your
John Deere dealer.
PY4964
A—Range Shift Lever
B—PTO Lever
C—Rockshaft Position Control Lever
D—Rockshaft Draft Control Lever
PY80265,05GO819 –19–04JUL06–1/1
45-1
022607
PN=35
Operating the Engine
Starting the Engine
1. Push hand throttle (A) forward off idle position
(approximately 1/3 of full throttle). Engine may not start
with throttle pulled completely down.
–UN–11JAN89
2. Make sure fuel shut-off knob (C) is pushed in.
Do not start engine by shorting across starter
terminals. Machine will start in gear and move if
normal circuitry is bypassed.
TS177
CAUTION: Avoid possible injury or death from a
machine runaway.
Machinery Runaway
Start engine only from operator’s seat with
transmission in NEUTRAL.
NEVER start engine while standing on ground.
–UN–13JAN05
IMPORTANT: DO NOT run a cold engine at full
throttle.
Hand Throttle and Key Switch
–UN–06AUG06
IMPORTANT: DO NOT operate starter more than 20
seconds at a time. If engine does not
start, wait at least two minutes for the
starter motor to cool before trying
again. If engine does not start in four
attempts, refer to “Troubleshooting”
section.
PY4497
3. Depress clutch pedal and turn key switch fully
clockwise (B) to engage starter. Release key when
engine starts. If key is released before engine starts,
wait until starter and engine stop turning before trying
again.
PY6082
A—Hand Throttle
B—Key Switch On
C—Fuel Shut Off Knob
Fuel Shut-off Knob
NR25796,0000346 –19–29DEC06–1/1
45-2
022607
PN=36
Operating the Engine
Check Instruments After Starting
–UN–31MAY06
IMPORTANT: If charging system (A) or oil pressure
(B) indicators fail to go out, or
temperature gauge (C) indicates hot,
stop engine and determine the cause.
PY5728
A—Charging System Indicator
B—Oil Pressure Indicator
C—Coolant Temperature Gauge
PY5754
–UN–01JUN06
For 5103, 5103S, 5203, 5104 and 5204 Tractor
For 5103E Tractor
PY80265,05GO821 –19–29DEC06–1/1
Oil Pressure Indicator
–UN–31MAY06
Oil pressure indicator (A) will light if engine oil pressure is
low. Indicator should light when key is turned to engage
starter and go out when engine starts.
PY5729
IMPORTANT: NEVER operate engine without
sufficient oil pressure. If indicator stays
lit for longer than five seconds under
normal operating conditions, stop
engine and check for cause.
For 5103, 5103S, 5203, 5104 and 5204 Tractor
If low oil level is not the problem, see your John Deere
dealer.
PY5755
–UN–01JUN06
A—Oil Pressure Indicator
For 5103E Tractor
PY80265,05GO822 –19–29DEC06–1/1
45-3
022607
PN=37
Operating the Engine
PY5756
PY5730
–UN–01JUN06
–UN–31MAY06
Charging System Indicator
For 5103, 5103S, 5203, 5104 and 5204 Tractor
For 5103E Tractor
A—Charging System Indicator
Charging system indicator (A) will light when alternator
output is low. Indicator should light when key is turned
to engage starter, and go out when engine starts.
loose or broken fan belt is not the cause, see your
John Deere dealer.
If indicator stays lit for longer than five seconds in
normal operation, stop engine and check for cause. If
PY80265,05GO823 –19–29DEC06–1/1
Air Restriction Sensor
Air restriction indicator (A) will light if air cleaner becomes
plugged. Service air cleaner as soon as possible.
–UN–31MAY06
Indicator should light momentarily when key is turned
slowly to starter engagement position.
PY5731
A—Air Restriction Indicator
For 5103, 5103S, 5203, 5104 and 5204 Tractor
PY80265,05GO824 –19–29DEC06–1/1
45-4
022607
PN=38
Operating the Engine
Air Restriction Sensor (5103E Tractor)
–UN–25AUG04
When red indicator is seen in transparent area of air
restriction sensor (A). Service air cleaner as soon as
possible.
PY4093
After servicing the air cleaner, reset the sensor by
pressing top of the sensor (B).
PY80265,05GO825 –19–04JUL06–1/1
PY5757
PY5732
–UN–01JUN06
–UN–31MAY06
Coolant Temperature Gauge
For 5103, 5103S, 5203, 5104 and 5204 Tractor
For 5103E Tractor
A—Coolant Temperature
Gauge
The needle on the temperature gauge (A) rises as
engine warms up. If needle reaches red zone, stop
engine and determine the cause.
Check coolant level in radiator when engine cools.
Also check grille, radiator and radiator side screens for
plugging. Check fan belt tension. If problem is not
corrected, see your John Deere dealer.
CAUTION: DO NOT remove radiator cap or
drain coolant until coolant is cold. Always
loosen radiator cap slowly to relieve any
excess pressure.
PY80265,05GO826 –19–29DEC06–1/1
45-5
022607
PN=39
Operating the Engine
Watch Fuel Level
Stop to refuel before gauge (A) reaches empty mark.
–UN–31MAY06
IMPORTANT: Use diesel fuel only. See Fuel and
Lubricants section for fuel
specifications.
PY5733
Should tractor run out of fuel and not start in several tries,
air must be bled from fuel system. (See Bleeding Fuel
System in Service section).
For 5103, 5103S, 5203, 5104 and 5204 Tractor
A—Fuel Gauge
PY80265,05GO827 –19–29DEC06–1/1
Watch Fuel Level (5103E Tractor)
Watch level indicator (A) for fuel level, while refilling tank.
Should tractor run out of fuel and not start in several tries,
air must be bled from fuel system. (See Bleeding Fuel
System in Service section).
PY4094
A—Level Indicator
–UN–20AUG04
IMPORTANT: Use diesel fuel only. See Fuel and
Lubricants section for fuel
specifications.
PY80265,05GO828 –19–04JUL06–1/1
45-6
022607
PN=40
Operating the Engine
PY4111
PY6083
–UN–21AUG04
–UN–06AUG06
Changing Engine Speeds
Foot Throttle
Hand Throttle
A—Hand Throttle
B—Foot Throttle
To increase speed, push hand throttle (A) forward.
To temporarily increase engine speed above hand
throttle setting, depress foot throttle (B).
NR25796,0000347 –19–04AUG06–1/1
PY5758
PY5734
–UN–01JUN06
–UN–31MAY06
Warming Up the Engine
For 5103, 5103S, 5203, 5104 and 5204 Tractor
For 5103E Tractor
Do not place tractor under full load until it is properly
warmed up.
2. Run engine at about 1900 rpm and under light load
until engine reaches normal operation condition.
1. Idle engine at about 1500 rpm for several minutes.
PY80265,05GO830 –19–29DEC06–1/1
45-7
022607
PN=41
Operating the Engine
Restart Stalled Engine
PY6084
–UN–06AUG06
Should the engine stall when operating under load,
depress clutch pedal (A) and restart it immediately to
prevent abnormal heat build up and continue with normal
operation or operate at slow idle for one or two minutes
before stopping.
NR25796,0000348 –19–04AUG06–1/1
PY5758
PY5734
–UN–01JUN06
–UN–31MAY06
Avoid Idling the Engine
For 5103, 5103S, 5203, 5104 and 5204 Tractor
Allowing engine to idle at low rpm uses fuel
inefficiently, and can cause a build-up of carbon in the
engine.
For 5103E Tractor
If tractor must be left with the engine running more
than three or four minutes, minimum engine speed
should be 1200 rpm.
PY80265,05GO832 –19–29DEC06–1/1
45-8
022607
PN=42
Operating the Engine
PY5758
PY5734
–UN–01JUN06
–UN–31MAY06
Observe Engine Work and Idle Speeds
For 5103, 5103S, 5203, 5104 and 5204 Tractor
For 5103E Tractor
Slow idle speed should be 850 ± 75 rpm. At light or no
load, full throttle speed will increase to 2500 rpm.
For correct PTO speed, run engine at 2200 rpm for
standard 540 rpm operation (load requiring full engine
power).
Normal working speed is 1400—2300 rpm rated
speed. Within these limits engine can be put under full
load.
PY80265,05GO833 –19–29DEC06–1/1
PY5759
PY5735
–UN–01JUN06
–UN–31MAY06
Working With Speed/Hour Meter
For 5103, 5103S, 5203, 5104 and 5204 Tractor
A—Tachometer
For 5103E tractor
B—2200 RPM Mark (540)
Tachometer (A) shows engine rpm, read in hundreds.
C—Hour Meter
Hour meter (C) shows hours of operation in full hours
and tenths.
For 540 rpm PTO speed, increase engine speed until
tachometer needle is aligned with 2200 rpm mark (B).
PY80265,05GO834 –19–29DEC06–1/1
45-9
022607
PN=43
Operating the Engine
Stopping the Engine
1. Pull hand throttle (A) down to slow idle position. Allow
engine to idle for one to two minutes.
3. Turn key switch to the OFF position (B).
4. Pull manual fuel shut-off knob (C) (at lower left side of
control support) rearward and hold until engine has
completely stopped.
PY4501
IMPORTANT: Cooling of certain engine parts is
provided by engine oil. Stopping a hot
engine suddenly could cause damage
to these parts by overheating or lack of
lubrication.
–UN–13JAN05
2. Put range shift lever in neutral (N) and set brakes.
–UN–06AUG06
CAUTION: Remove key from key switch to
prevent operation by untrained personnel.
PY6082
A—Hand Throttle
B—Key Switch OFF Position
C—Fuel Shut Off Knob
NR25796,0000349 –19–04AUG06–1/1
45-10
022607
PN=44
Operating the Engine
Using Booster Battery
Battery gas is explosive:
–UN–12JUL06
DO NOT smoke while charging battery.
Keep all flames and sparks away.
DO NOT charge frozen battery.
DO NOT connect booster battery negative (—) cable to
starting vehicle negative (—) terminal.
PY5821
•
•
•
•
1. Access battery. (See procedure in Service section.)
2. Connect positive (+) booster cable to booster battery
positive (+) post (D).
3. Connect the other end of positive (+) booster cable to
tractor battery positive (+) post (A).
A—Tractor Battery Positive (+) Post
B—Engine Ground
C—Booster Battery Negative (—) Post
D—Booster Battery Positive (+) Post
4. Connect negative (—) booster cable to booster battery
negative (—) post (C).
5. Connect the other end of negative (—) booster cable to
engine ground (B), away from battery and starter.
PY80265,05GO836 –19–11JUL06–1/1
45-11
022607
PN=45
Driving the Tractor
Operator Training Required
• Study the Operation section of this manual before
operating tractor.
• Operate tractor in an open, unobstructed area under
direction of an experienced operator.
• Learn use of all controls.
• Operator experience is required to learn moving,
stopping, turning and other operating characteristics
of tractor.
NR25796,000034A –19–04AUG06–1/1
Driving on Public Roads
PY6085
–UN–06AUG06
CAUTION: When transporting on a public road
or highway, use accessory lights and devices
for adequate warning to operators of other
vehicles. Check local governmental regulations.
Various safety devices are available from your
John Deere dealer. Keep safety items in good
condition. Replace missing or damaged items.
Observe the following precautions when operating the
tractor on the road:
Brake pedals
A—Brake Pedals Locking Plate
CAUTION: Before operating tractor on a road,
lock brake pedals together. Use brake lightly
and cautiously at transport speeds.
1. Couple brake pedals together using brake locking bar
(A). Avoid hard applications of brakes. Reduce speed if
towed load weighs more than the tractor and is not
equipped with brakes.
Use additional caution when transporting towed loads
under adverse surface conditions and when turning or
braking on inclines. Be sure wheel tread is adjusted
wide to provide maximum stability.
IMPORTANT: To prevent unnecessary wear, never
ride the brakes by resting a foot on the
pedals.
Continued on next page
50-1
NR25796,000034B –19–29DEC06–1/2
022607
PN=46
–UN–09JUN06
PY5014
PY5013
–UN–09JUN06
Driving the Tractor
Always turn light switch to dim lights position (A) when
meeting another vehicle. Never use flood lamps or any
other lights which could blind or confuse other drivers.
4. Use turn signal when turning. Be sure to return lever
(E) to center position after turning.
5. Drive slowly enough to maintain safe control at all
times. Before descending a hill, shift to a gear low
enough to control speed without using brakes. Slow
down for rough ground, and sharp turns, especially
when transporting heavy, rear mounted equipment.
–UN–09JUN06
3. Turn light switch to position (D).
PY4137
2. Check local laws and regulations for lighting
requirements. Be sure Slow Moving vehicle (SMV)
emblem (G), turn signal lights (B) and tail lights (F) are
clean and visible. If towed or rear-mounted equipment
obstucts these safety devices, install SMV emblem and
warning lamps on equipment. (See your John Deere
dealer)
–UN–09JUN06
For 5103E Tractor
PY4136
For 5103, 5103S, 5203, 5104 and 5204 Tractor
A—Dim Headlight Switch Position
B—Turn Signal Light
C—Reflex Reflector
D—Bright Headlight Switch Position
E—Turn Signal Lever
F—Tail Light
G—SMV Emblem
NR25796,000034B –19–29DEC06–2/2
50-2
022607
PN=47
Driving the Tractor
PY5807
PY5824
–UN–12JUN06
–UN–20JUN06
Operating Transmission
Speed Shift Lever
Range Shift Lever
A—Range Shift Lever
B—Speed Shift Lever
Range shift lever (A) provides two forward speed
ranges, (A and B) and one reverse range (R).
Range shift must be in neutral for the engine to be
started.
Speed shift lever (B) provides four travel speeds.
Using range and speed shift levers in different
combinations, eight forward speeds and four reverse
speeds can be obtained.
NR25796,000034C –19–04AUG06–1/1
Depress clutch pedal (A) and stop tractor before shifting
either range shift lever or speed shift lever. Release clutch
pedal gradually to take up load smoothly.
PY6084
IMPORTANT: To prevent transmission damage, do
not use speed shift on-the-go. To
prevent unnecessary wear, never “ride”
the clutch by resting a foot on the
pedal.
–UN–06AUG06
Shifting Transmission
A—Clutch Pedal
NR25796,000034D –19–04AUG06–1/1
50-3
022607
PN=48
Driving the Tractor
PY5807
PY5824
–UN–12JUN06
–UN–20JUN06
Operating Transmission
Speed Shift Lever
Range Shift Lever
A—Range Shift Lever
Range shift lever (A) provides two forward speed
ranges, (A and B) and one reverse range (R).
B—Speed Shift Lever
Range shift must be in neutral for the engine to be
started.
Speed shift lever (B) provides four travel speeds.
Using range and speed shift levers in different
combinations, eight forward speeds and four reverse
speeds can be obtained.
PY80265,05GO839 –19–20JUN06–1/1
50-4
022607
PN=49
Driving the Tractor
PY5758
PY5734
–UN–01JUN06
–UN–31MAY06
Selecting a Gear
For 5103, 5103S, 5203, 5104 and 5204 Tractor
IMPORTANT: To extend drive train life and avoid
excessive soil compaction and
rolling resistance when using
ballast, operate one gear lower than
normal.
The tractor may be operated in any gear with engine
speeds between 1400 rpm and 2300 rated engine rpm.
For 5103E Tractor
Within these limits the engine can be put under full
load. For light load operation, use a higher gear and
lower engine speed. This saves fuel and reduces
wear.
Ground Speed Estimates for different tyre sizes are
located in Specifications section.
PY80265,05GO841 –19–29DEC06–1/1
50-5
022607
PN=50
Driving the Tractor
Using Brakes
–UN–06AUG06
CAUTION: Before operating tractor on a road,
lock pedals together. Use brake lightly and
cautiously at transport speeds.
PY6085
Use individual brakes to assist in making sharp turns.
Disengage brake pedal locking bar (A) and depress only
one brake pedal.
To stop tractor, depress both brake pedals.
IMPORTANT: To prevent unnecessary wear, never
ride the brakes by resting a foot on the
pedals.
Brake Pedals
A—Brake Pedal Locking Bar
Reduce speed if towed load is not equipped with brakes
and weighs more than the tractor. Avoid hard braking
applications. Consult implement operators manual for
recommended transport speeds.
Use additional caution when transporting towed loads
under adverse conditions, when turning or stopping on
inclines.
NR25796,000034E –19–04AUG06–1/1
50-6
022607
PN=51
Driving the Tractor
Using Differential Lock (Optional For 5103E
Tractor )
–UN–06AUG06
CAUTION: DO NOT operate tractor at high
speed or attempt to turn with differential lock
engaged.
PY6081
IMPORTANT: To prevent damage to drive train, DO
NOT engage differential lock when one
wheel is spinning and the other is
completely stopped.
Differential Lock Pedal
When one wheel starts to lose traction, engage differential
lock by depressing pedal (A) down.
A—Differential Lock Pedal
Unequal traction will keep the lock engaged. When
traction equalizes, lock will disengage itself by spring
action. If lock does not disengage, depress one brake
pedal and then the other.
If tyres repeatedly slip, then get traction, then slip again,
hold pedal in the engaged position.
NR25796,000034F –19–04AUG06–1/1
50-7
022607
PN=52
Driving the Tractor
CAUTION: Always place the range shift lever in
neutral (N) and set brakes before dismounting.
Leaving transmission in gear with engine off
MAY NOT prevent tractor from moving.
PY6080
1. Stop the tractor and place range shift lever (A) in
neutral.
–UN–06AUG06
Stopping Tractor
2. Apply brakes.
3. Lower all equipment to ground using rockshaft position
control lever (D) and rockshaft draft control lever (C),
CAUTION: Remove the key from key switch to
prevent operation by untrained personnel.
PY4911
IMPORTANT: Cooling of certain engine parts is
provided by engine oil. Stopping a hot
engine suddenly could cause damage
to these parts by overheating or lack of
lubrication.
–UN–14APR05
4. Pull hand throttle (B) down to slow idle position. Allow
engine to idle for one to two minutes.
5. Turn key switch to OFF position.
6. Pull manual fuel shut-off knob (E) (at lower left side of
control support) rearward and hold until engine has
completely stopped.
PY6086
–UN–06AUG06
PY4138
–UN–26AUG04
A—Range Shift Lever
B—Hand Throttle Lever
C—Rockshaft Draft Control Lever
D—Rockshaft Position Control Lever
E—Fuel Shut Off Knob
NR25796,0000351 –19–04AUG06–1/1
50-8
022607
PN=53
Rockshaft and 3-Point Hitch
Match Tractor Power to Implement
IMPORTANT: Tractor power should be matched to the
size of certain implements. Excessive
power can damage an implement, and
too large an implement can damage the
tractor. (Refer to your implement
operator’s manual for minimum and
maximum power requirements before
attaching an implement.)
PY80265,05GO845 –19–10SEP05–1/1
PY4959
–UN–27APR05
3-Point Hitch Components
A—Lift Arms
B—Lift Links
C—Sway Chains
D—Center Link
E— Draft Links
PY80265,05GO846 –19–12JUN06–1/1
55-1
022607
PN=54
Rockshaft and 3-Point Hitch
Rockshaft Control Levers
The rockshaft position is controlled by two levers, the
rockshaft position control lever (A) and the rockshaft draft
control lever (B)
PY4960
The rockshaft draft control lever (B) controls hitch position
relative to draft loads. See Using Draft Control in this
section for more information.
–UN–22APR05
The rockshaft position control lever (A) raises the hitch
when pulled rearward, and lowers the hitch when moved
forward. See Using Rockshaft Position Control in this
section for more information.
A—Rockshaft Position Control Lever
B—Rockshaft Draft Control Lever
PY80265,05GO848 –19–04JUL06–1/1
Setting Position Control Lever Stop
2. Loosen lever stop (A), and slide against position
control lever. Lock stop in position by turning in a
clockwise direction. Rockshaft will now lower to same
position each time control lever is pushed forward to
the stop.
PY4961
1. Operate implement for a few minutes to determine
proper depth or height.
–UN–22APR05
NOTE: Position control lever stop is used when operating
depth or height needs to be repeated.
A—Lever Stop
PY80265,05GO849 –19–10SEP05–1/1
55-2
022607
PN=55
Rockshaft and 3-Point Hitch
Using Rockshaft Position Control
Use position control lever (A) to control hitch movement
and depth. Position control should be used for the
following applications:
PY4960
Put draft control lever (B) forward when you DO NOT
want rockshaft to adjust automatically to draft load, such
as attaching implement to tractor.
–UN–22APR05
CAUTION: To prevent unexpected movement of
rockshaft, place draft control lever (B) in a full
forward position before attaching an implement.
TRANSPORT of implements and end of field turn-around.
Position control lever should be moved fully rearward (C)
for transport for both load and non-load sensing usage.
CONSTANT DEPTH of implements on level terrain and
for non- ground engaging implements such as spreaders
or sprayers. Place position control lever at depth desired
(D).
FLOAT operation for implements with skids or depth
gauge wheels designed to carry full implement weight.
Push both levers all the way forward (E) so implement
can follow the ground contour.
NOTE: Lift links can be adjusted for lateral float. (See
Lateral Float in this section.)
M47168
–UN–31JAN92
A—Rockshaft Position Control Lever
B—Rockshaft Draft Control Lever
C—Position Control Lever in Rearward Position
D—Position Control Lever in Desired Depth Position
E—Position Control Lever and Draft Control Lever in
Float Position
PY80265,05GO850 –19–10SEP05–1/1
55-3
022607
PN=56
Rockshaft and 3-Point Hitch
Using Draft Control
The rockshaft may be equipped with variable draft control
system.
–UN–27APR05
Use draft load sensing when:
PY4965
• Operating with a fully mounted implement in hill and
swale terrain. The implement will raise and lower to
follow the ground contours while maintaining a nearly
constant depth.
• Operating in varying soil conditions. The implement is
raised slightly to get through tough spots so you do not
have to shift to a lower gear.
Draft control lever (B) controls amount of load required
before hitch responds. With lever placed fully forward to
the position marked “off” (C), there is no draft sensing.
Placing the lever toward the rear position reduces the
amount of draft load required to override the position
setting set by the position control lever (A) and raise the
rockshaft.
Draft sensitivity ranges can be changed by repositioning
the center link. (See Positioning Center Link in this section
for additional information.)
M47169
• Initially place position control lever (A) in its fully
rearward position and the draft control lever (B) in the
fully forward (least draft) position.
• With tractor moving, push position control lever (A)
forward to set implement operating depth. Set position
control lever stop (D) so control lever can be brought
back to the same position. The operating depth set-up
will prevent the rockshaft from lowering all the way
when the tractor begins to slip. Then pull draft sensing
lever (B) rearward until desired draft sensing sensitivity
is obtained.
• The position control lever (A) can also be raised slightly
to override the draft control setting to help get through
slippery spots without getting stuck.
• The position control lever (A) can be moved fully
rearward to raise the hitch at the end of the field.
–19–29JAN92
For draft load sensing operation:
A—Rockshaft Position Control Lever
B—Rockshaft Draft Control Lever
C—Draft Sensing OFF Position
D—Position Control Lever Stop
PY80265,05GO851 –19–10SEP05–1/1
55-4
022607
PN=57
Rockshaft and 3-Point Hitch
Adjusting Rockshaft Rate-of-Drop/ Implement
lock
–UN–11AUG04
CAUTION: Excessive rate-of-drop may cause
damage or injury. Fully lowering implement
should require at least two seconds.
PY4076
Rockshaft drops faster when a heavy implement is
attached. Adjust rate-of-drop knob so that it is slow
enough to be safe and prevent implement damage.
Turn rockshaft rate-of-drop knob (A), located under the
seat, clockwise to slow rockshaft drop.
A—Rockshaft Rate-of-Drop Knob cum Implement
Lock
Turn knob counterclockwise to increase rate-of-drop.
Rate-of-drop knob is also called implement lock. When
knob is fully screw in, implement will not lower down even
if position control lever is fully down. Use implement lock
while transporting implement.
PY80265,05GO852 –19–10SEP05–1/1
Attaching Tipping Trailer
PY4096
NOTE: When tipping trailor is not attached to tractor, fully
screw-out preselector knob, otherwise rockshaft
will not function.
–UN–21AUG04
Hydraulic power can be extended to tipping trailor through
auxiliary port (A). When preselector (B) is fully screwed-in,
hydraulic oil will move to tipping trailer. Use draft control
lever for lowering or raising of trailor.
A—Auxiliary Port
B—Preselector Knob
PY80265,05GO853 –19–10SEP05–1/1
55-5
022607
PN=58
Rockshaft and 3-Point Hitch
Preparing Implement
II
Mast
Height
610 mm
(24 in.)
Width
Between
Lower Pins
824 mm
(32-7/16 in.)
Pin Size
Lower
Upper
28.7 mm
(1-1/8 in.)
25.5 mm
(1 in.)
PY2274
Category
–UN–07JUN06
Category II implements should have the top hole of the
implement mast located 610 mm (24 in.) above the lower
pins. Drill another hole in top mast or extend top mast if
necessary.
PY80265,05GO854 –19–10SEP05–1/1
55-6
022607
PN=59
Rockshaft and 3-Point Hitch
Positioning Center Link
–UN–11DEC05
The draft sensing rockshaft center link attaching bracket
has holes which allow three different positions for
attaching the center link. The position effects the draft
sensing sensitivity.
Standard position is (C).
• Excessive hitch activity or hunting occurs in draft control
operation.
• The rear of the implement raises too much when lifted.
The implement weight which can be lifted is reduced
slightly with the center link attachment in the lower
holes.
• The draft control lever range is too small.
PY4967
Move the center link attachment to holes (B) if:
A—Upper Hole
B—Middle Hole
C—Lower Hole
Move the center link attachment to holes (C) if:
• The hitch seems unresponsive in draft control operation
and allows the engine speed to drop too far before
raising the rockshaft.
• The rear of the implement droops and drags the ground
as the implement is lifted.
Upper hole (A) eliminates nearly all draft sensing.
NOTE: Implements with Category II mast height 610 mm
(24 in.) will use the upper two holes.
PY80265,05GO855 –19–10SEP05–1/1
55-7
022607
PN=60
Rockshaft and 3-Point Hitch
Attaching Implements to 3-Point Hitch
–UN–09DEC05
1. Be sure drawbar will not interfere. If necessary, move
drawbar ahead, or remove it. Check for any other
potential interference.
PY5374
CAUTION: Prevent unexpected movement of
rockshaft by placing draft sensing lever in the
forward or OFF position before attaching
implement to hitch.
2. Back tractor up to implement (A) so hitch points (B)
align. Place transmission in neutral (N), stop the
engine and engage brakes BEFORE leaving the tractor
seat.
–UN–09DEC05
3. Slip draft links over implement hitch pins (B), and
retain with quick-lock pins.
PY5375
NOTE: Locking pins can be stored on draft links (through
holes in sway chain ears) when not in use.
4. To remove center-link from transport hook, lift center
link locking clip (C), and rotate tab (D) to rear of center
link clip.
5. Attach center link to implement top mast.
–UN–11DEC05
6. Adjust center link and lift links as necessary. (See
Leveling the Hitch in this section.)
PY5376
CAUTION: To avoid bodily injury or machine
damage whenever an implement, implement
quick coupler, or other attachment is connected
to the tractor 3-Point Hitch, check full range of
operation for interference, binding or PTO
separation.
A—Implement
B—Implement Hitch Pins
C—Center Link Locking Clip
D—Tab
E—Rockshaft Position Control Lever
F—Rockshaft Draft Control Lever
7. Using rockshaft position control lever (E), lower and
raise implement slowly and check for any point of
interference.
PY80265,05GO856 –19–10SEP05–1/1
55-8
022607
PN=61
Rockshaft and 3-Point Hitch
Adjusting Hitch Side Sway
NOTE: Check implement operator’s manual for instruction
on whether to allow side sway.
NOTE: Use spring or rubber strap to keep draft links out
of rear tyres when draft links are not attached to
implement.
PY4970
–UN–10DEC05
Implement side sway should be adjusted when the
rockshaft is raised for transport by loosening the jam nut
on the threaded link (A) and turning the center rod to
increase or decrease the length of chain. Tighten jam nut
again when adjusted.
A—Threaded Link
PY5825
–UN–20JUN06
For 5103, 5103S, 5203, 5104 and 5204 Tractor
For 5103E Tractor
PY80265,05GO857 –19–29DEC06–1/1
55-9
022607
PN=62
Rockshaft and 3-Point Hitch
Leveling the Hitch
1. Lower implement to take weight off hitch.
–UN–23APR05
IMPORTANT: DO NOT attempt to overextend center
link beyond limits of locking clip or lift
links past the stops. Link body threads
could be damaged.
PY4968
NOTE: Maximum adjustment range of the center link can
only be obtained if the ends are positioned equally
within the body when attached to an implement.
2. Adjust center link to level implement front-to-rear.
Unlatch locking clip (A). Rotate center link body
clockwise to lengthen center link or counterclockwise to
shorten it. Be sure to latch the locking clip.
3. Adjust right-hand link to level implement side-to-side.
Lift locking handle (C) and turn 1/4 turn to engage slot
(D) onto roll-pin in the center portion of the lift link.
–UN–12JUL06
Turn crank handle (C) clockwise to raise draft link.
After adjustment, lift handle (C) and turn to engage slot
(D) onto the lower body to prevent change of
adjustment during operation.
PY5914
Turn crank handle (C) counterclockwise to lower draft
link.
For 5103, 5103S, 5203, 5104 and 5204 Tractor
4. The left-hand lift link is also adjustable in length to
accommodate different tyre sizes.
PY5915
Adjust left and right lift links to accommodate various
tyre sizes. Set the lift links to have fully-lowered draft
link balls approximately seven inches off the ground for
greatest range of usable hitch motion.
–UN–12JUL06
To change the left-hand lift link length, remove the
upper lift link pin and rotate the upper end assembly
clockwise to shorten or counterclockwise to lengthen,
and then reinstall the upper pin and locking pin.
For 5103E Tractor
A—Locking Clip
B—Center Link Body
C—Locking Handle
D—Slot
PY80265,05GO858 –19–29DEC06–1/1
55-10
022607
PN=63
Rockshaft and 3-Point Hitch
Adjusting Lateral Float
–UN–10DEC05
PY5381
To hold implement rigid, place head of float pin and the
rectangular washer in the horizontal position (B).
Use lift link pins in the float position for hitch-mounted
implements such as a cultivator or mower, which have
ground gauging skids or wheels which may cause the
implement to twist relative to the tractor.
PY5380
–UN–10DEC05
To allow the draft link to raise slightly as implement
follows ground contour, place head of float pin and the
rectangular washer on the inside end of the pin in a
vertical position (A).
A—Pin in Vertical Position
B—Pin in Horizontal Position
Use the rigid position for implements such as plows and
ground engaging implements that should not twist relative
to the tractor.
PY80265,05GO859 –19–10SEP05–1/1
A—Adjustment Set Screws
Back Side Of Control Lever
If the rockshaft position control lever or rockshaft draft
control lever do not stay in set position, increase lever
–UN–10DEC05
PY4385
PY4406
–UN–10DEC05
Adjusting Rockshaft Control Lever Friction
B—Adjustment Set Screws
Front Side Of Control
Lever
friction by tightening the set screws (A) for the
appropriate lever until the proper friction is obtained.
PY80265,05GO860 –19–10SEP05–1/1
55-11
022607
PN=64
Rockshaft and 3-Point Hitch
Warming Hydraulic System Oil
–UN–06AUG06
Hydraulic system may be slow to function when tractor is
started in cold weather. This is because cold oil will not
flow as easily through the hydraulic system filter (A).
Steering may be slow until system warms up.
PY6097
Hydraulic system will function normally when oil warms
up.
A—Hydraulic Oil Filter
Right Side of Transmission
NR25796,0000352 –19–29DEC06–1/2
–UN–31MAY06
IMPORTANT: To prevent damaging hydraulic pump or
relief valve, DO NOT exceed two to
three minutes warm-up time with
steering wheel held in full left or full
right turn position.
1. Depress clutch pedal, start engine and idle at about
1000 rpm.
PY5734
2. Turn and hold steering wheel in full left or right turn.
PY5758
–UN–01JUN06
For 5103, 5103S, 5203, 5104 and 5204 Tractor
For 5103E Tractor
NR25796,0000352 –19–29DEC06–2/2
55-12
022607
PN=65
Drawbar and PTO
Observe Drawbar Load Limitations
–UN–10APR05
IMPORTANT: Certain heavy equipment, such as a
loaded single-axle trailer, can place
excessive strain on drawbar. Strain is
greatly increased by speed and rough
ground.
PY1094
Static vertical load on drawbar should
not exceed 556 kg (1225 lb).
Drive slowly with heavy loads.
Drawbar
Specification
Drawbar Static Vertical Load—
Capacity ........................................................... 556 kg (1225 lb) Maximum
NR25796,0000257 –19–11JUL06–1/1
Stay Clear of Rotating Drivelines
Wear close fitting clothing. Stop the engine and be sure
PTO driveline is stopped before making adjustments,
connections, or cleaning out PTO driven equipment.
TS1644
Keep tractor master shield and driveline shields in place
at all times. Make sure rotating shields turn freely.
–UN–22AUG95
Entanglement in rotating driveline can cause serious injury
or death.
PY80265,05GO862 –19–10SEP05–1/1
65-1
022607
PN=66
Drawbar and PTO
Attaching PTO-Driven Implement
–UN–10APR05
CAUTION: Stop engine before attaching
implement or working in area of implement
hitch.
PY1094
1. Attach implement to tractor before connecting PTO
drive line. Raise hitch to upward position if it is not to
be used.
2. Range shift lever in neutral (N), key to OFF position to
stop engine and set brakes.
3. If PTO driven implement will be attached to drawbar
(A), the drawbar must be positioned so there is 355
mm (14 in.) between end of PTO shaft and center of
drawbar pin hole. Make sure drawbar locking pins and
spring pins are in place. If implement will be connected
to 3-Point Hitch, be sure drawbar will not interfere.
Remove it if necessary.
A—Drawbar
NOTE: There are two holes at the front of the drawbar.
Place the drawbar pin in the second hole for the
proper 355 mm (14 in.) length.
4. Rotate PTO shield upward for clearance. With engine
off, turn shaft slightly by hand if necessary to line up
splines. Connect drive line to PTO shaft. Pull out on
shaft to be sure drive line is locked to PTO shaft. Place
PTO shield in downward position.
5. Be sure all shields are in place and in good condition.
Never operate PTO unless master shield is properly
installed. WITH ENGINE STOPPED, check integral
shields on drive line by making sure they rotate freely
on shaft. Lubricate or repair as necessary.
6. Check carefully for any interference, make sure hitch is
raised to the upper position if it is not used.
PY80265,05GO863 –19–10SEP05–1/1
65-2
022607
PN=67
Drawbar and PTO
PY5736
PY4485
–UN–16FEB06
–UN–31MAY06
Operating Tractor PTO
Hand Throttle Lever
For 5103, 5103S, 5203, 5104 and 5204 Tractor
1. Depress clutch pedal, start engine and push hand
throttle lever (A) forward until engine speed is sufficient
to start PTO implement. Engine speed must be less
than 2200 rpm (B).
–UN–01JUN06
2. Move control lever (A) forward to engage PTO. PTO
indicator (B) will light when PTO is engaged.
PY5760
3. Increase engine speed to rated PTO speed of 2200
rpm for 540 operation.
For 5103E Tractor
A—Hand Throttle Lever
B—540 Operation Speed
Continued on next page
65-3
PY80265,05GO864 –19–29DEC06–1/2
022607
PN=68
Drawbar and PTO
–UN–10DEC05
CAUTION: Turn key OFF and pull Fuel Shut-off
Knob to stop engine, set brakes and make sure
all mechanisms have stopped before cleaning
out machine or making any adjustments to PTO
driven implement.
4. Pull control lever back to disengage PTO.
PY5383
C—PTO Control Lever
PY5382
–UN–10DEC05
Dual Clutch
Single Clutch
PY80265,05GO864 –19–29DEC06–2/2
65-4
022607
PN=69
Drawbar and PTO
PY5912
–UN–11JUL06
Adjusting PTO Clutch Operating Rod
–UN–02NOV99
1. Move PTO lever (A) to rearward (disengaged) position.
LV4082
2. Remove clip pin (B) from forward end of PTO clutch
rod.
3. Check for equal thread engagement at turnbuckle (G).
Loosen jam nuts (F) and (C). Turn rod (D) until threads
on each side of turnbuckle are equal. Tighten jam nut
(F).
4. Loosen jam nut (C) from rear of front clevis (E).
5. Adjust length of arm (D) so the clip pin (B) can be
inserted with the rod pulled forward and the arm pulled
rearward to eliminate free play. Lengthen rod by turn of
the clevis to provide PTO clutch lever free play and
PTO clutch rod travel in fully engaged position to
specification.
–UN–21MAY05
Specification
PTO Clutch Lever—Free Play ........................................................ 15 mm
PTO Clutch Rod (In Fully
Engaged Position)—Travel................................................ 14 mm -16 mm
PY5019
NOTE: Adjust turnbuckle (G) if you cannot make proper
adjustment with clevis.
6. Reinstall clip pin (B) in clevis (E) and arm (D).
7. Tighten jam nut (C) at clevis.
A—PTO Clutch Lever
B—Clip Pin
C—Jam Nut
D—Arm
E—Clevis
F—Jam Nut
G—Turnbuckle
PY80265,05GO865 –19–11JUL06–1/1
65-5
022607
PN=70
Ballast
Planning for Maximum Productivity
Proper ballasting is an important factor in tractor
performance. maximum productivity can be achieved
only if tractor weight is appropriate for the job.
FMO-Machinery Management includes information on
tractor and implement matching and increasing
productivity. .
John Deere FMO (Fundamentals of Machine
Operations) Tractors, discusses methods of
determining correct tractor weight and ballast selection.
Your John Deere dealer can assist you with
information on these subjects.
PY80265,05GO866 –19–10SEP05–1/1
Selecting Ballast Carefully
Match amount of ballast needed for each job. What is
right for one job may be wrong for another job. Ballast
for traction and stability.
Factors determining amount of ballast:
•
•
•
•
•
Soil surface-loose or firm.
Type of implement-integral/semi-integral or towed.
Travel speed-slow or fast.
Tractor power output-partial or full load.
tyres-single, oversize, or dual.
PY80265,05GO867 –19–10SEP05–1/1
Matching Ballast to Load Work
Too Little Ballast
Use no more ballast than necessary, and remove
ballast when it is no longer needed.
Rather than weighing tractor down to pull heavy loads,
try to reduce load. Pulling a lighter load at a higher
speed is more economical and more efficient.
The best way to check for correct ballast is to measure
amount of travel reduction (% slip) of the drive wheels.
Under normal field conditions, travel reduction should
be 10—15 percent.
Too Much Ballast
1.
Excessive wheel slip
1.
Increased load
2.
Power loss due to
churning soil
2.
Power loss due to
carrying extra weight
3.
tyre wear
3.
tyre strain
4.
Fuel waste
4.
Soil compaction
5.
Lower productivity
5.
Fuel waste
6.
Lower productivity
Add more weight to drive wheels if slip is excessive. If
there is less than 10 percent slip, weight should be
removed.
PY80265,05GO868 –19–10SEP05–1/1
70-1
022607
PN=71
Ballast
Measuring Wheel Slip—Manually
1. Place a mark (A) on a rear tyre which is easily
observed (a chalk mark is recommended).
2. With tractor working and implement lowered, mark a
starting point (B) on the ground at the place where the
tyre mark (A) meets the ground.
3. Mark the ground again where the tyre mark (A)
completes 10 full revolutions (C).
4. With implement raised return in the opposite direction.
At the second mark on the ground (C) remark the tyre
(D).
6. Use the return tyre revolutions count and “Wheel
Slippage Chart” to determine slippage. 10—15 percent
is ideal.
M47166
7. Adjust ballast or load to give correct slippage.
–UN–31JAN92
5. While driving the tractor along the same path
(implement raised), count the tyre revolutions required
to reach the starting point (B).
NOTE: Available horsepower is greatly reduced when
wheel slip drops below 10 percent.
WHEEL SLIPPAGE CHART
Non-Loaded Wheel
Revolutions (Step 5)
Estimated %
Slip
Recommended Action
10
0
Remove Ballast
9-1/2
5
Remove Ballast
9
10
Proper Ballast
8-1/2
15
Proper Ballast
8
20
Add Ballast
7-1/2
25
Add Ballast
7
30
Add Ballast
PY80265,05GO869 –19–10SEP05–1/1
70-2
022607
PN=72
Ballast
Ballast Limitations
Ballast should be limited by either tyre capacity or
tractor capacity. Each tyre has a recommended
carrying capacity which should not be exceeded (see
Wheels, tyres and Treads section). If a greater amount
of weight is needed for traction, a larger tyre should be
considered.
Ballast can be added as either liquid or cast iron.
PY80265,05GO870 –19–10SEP05–1/1
Ballasting Front End for Transport
CAUTION: Weights are heavy. Use proper lifting
equipment. Approximate weight of starter
weight (C) is : 49 kg (109 lb). Approximate
weight of QUIK-TATCH weights (D) are 45 kg
(99 lb).
Specification
Starter Weight (Ballast)—Weight ......................................... 49 kg (109 lb)
QUIK-TATCH Weight
(Ballast)—Weight .......................................................... 45 kg (99 lb) Each
PY4523
–UN–24JAN05
CAUTION: Additional front ballast may be
needed for transporting rear-mounted
implements. When implement is raised, drive
slowly over rough ground, regardless of how
much ballast is used.
A—Ballast Center
B—Ballast Retaining Bolts
C—Starter Weight
D—QUIK-TATCH Weights
Installing QUIK-TATCH Weights: QUIK-TATCH
weights can be installed on the front of the tractor.
One starter weight and up to 8 QUIK-TATCH weights
can be installed.
1. Install weights in pairs, one on each side of center (A).
2. To hold weights in place, run retaining bolts (B)
through holes from side-to-side. Tighten to
specification.
Specification
Ballast Weights Retaining Bolts—
Torque ........................................................................ 230 N•m (170 lb-ft)
QUIK-TATCH is a trademark of Deere & Company
PY80265,05GO871 –19–10SEP05–1/1
70-3
022607
PN=73
Ballast
Ballasting Front End for Transport (5103E
Tractor)
–UN–12JUN06
CAUTION: Additional front ballast may be
needed for transporting rear-mounted
implements. When implement is raised, drive
slowly over rough ground, regardless of how
much ballast is used.
PY4099
CAUTION: Weights are heavy. Use proper lifting
equipment. Approximate weight of Front
Bumper (A) is : 61 kg (135 lb). Approximate
weight of each Ballast weight (C) is 23 kg (51
lb).
Front Bumper
Specification
Front Bumper—Weight ......................................................... 61 kg (135 lb)
Ballast Weight—Weight .......................................................... 23 kg (51 lb)
A—Front Bumper
B—Ballast Center
C—Ballast Weight
D—Ballast Retaining Bolt
Installing Weights: Upto 8 weights can be installed on the
front bumper of the tractor as per requirement.
1. Install weights in pairs, one on each side of ballast
center (B).
2. To hold weights in place, run retaining bolts (D)
through holes. Tighten to specification.
Specification
Ballast Weights Retaining Bolts—
Torque .......................................................................... 130 N•m (96 lb-ft)
PY80265,05GO872 –19–12JUN06–1/1
Ballasting Tractor
Add weight to front end if needed for stability. Heavy
pulling and heavy rear-mounted implements tend to lift
front wheels. Add enough ballast to maintain steering
control and prevent tip-over.
Refer to the implement operator’s manual, along with
“Using Implement Codes” in this section, to determine
the minimum number of front weights that are required
for your tractor model.
PY80265,05GO873 –19–10SEP05–1/1
70-4
022607
PN=74
Ballast
Determining Maximum Rear Ballast
IMPORTANT: DO NOT overload tyres. If maximum
weight shown in chart is not enough
for safety, reduce load or install
heavier ply tyres.
pulling heavy loads in the first three
gears.
Chart shows carrying capacity per tyre.
MAXIMUM LOAD PER WHEEL
To extend drive train life, avoid
excessive soil compaction and
rolling resistance, avoid adding too
much ballast. Ballast should never
exceed the weight required to
provide traction for continuous full
power loads in 3rd gear. Remove
ballast if tractor engine labors when
Tyre Size
Bias Ply tyres
Ply Rating
Capacity
kg (lb)
14.9-28
12
1545 (3406)
13.6-28
12
1329 (2930)
12.4-28
12
1211 (2670)
PY80265,05GO874 –19–10SEP05–1/1
Determining Maximum Front Ballast
MAXIMUM LOAD PER WHEEL
Use appropriate front ballast for a particular operating
condition. Two-wheel drive tractors should only have
enough ballast to maintain safe steering control.
Remove ballast when it is no longer needed.
2-WD
Chart shows carrying capacity per tyre.
Tyre Size
Ply Rating
Capacity
kg (lb)
6.00-16
8
534 (1177)
6.50-20
8
725 (1599)
IMPORTANT: DO NOT overload tyres. If maximum
weight shown in chart is not enough
for safety, reduce load or install
tyres with a higher load rating.
PY80265,05GO875 –19–17JAN07–1/1
Using Cast Iron Weights
M47215
Specification
Cast Iron Weights—Weight .................................................. 48 kg (106 lb)
–UN–29JAN92
Cast iron weights are available in a 48 kg (106 lb) size.
Weights can be installed on the inside or outside of wheel.
See your John Deere dealer for more information and
recommendations on weight use and placement.
PY80265,05GO876 –19–10SEP05–1/1
70-5
022607
PN=75
Ballast
Installing Rear Cast Iron Weights
–UN–17FEB06
CAUTION: Optional cast iron weight weighs 48
kg (106 lb). Handle with care! Use appropriate
equipment or have the job done by your John
Deere dealer.
1. Attach first weight to wheel disks.
PY1635
2. To install additional weights (A), install bolts in previous
weight (B). Rotate the added weight to align bolts with
weight holes (C).
A—Additional Weight
B—Weight
C—Weight Holes
3. Tighten attaching bolts securely. Tighten again after a
few hours service. Check tightness regularly.
PY80265,05GO877 –19–10SEP05–1/1
Using Liquid Weight
CAUTION: Installing liquid ballast requires
special equipment and training. Have the job
done by your John Deere dealer or a tyre
service store.
Charts on this page show how much each tyre size
holds if filled to 75 percent full.
LIQUID WEIGHT FOR FRONT TYRES
With 0.6 kg/L (5 lb/gal) Calcium Chloride Solution
IMPORTANT: NEVER fill tyre to more than 75%
full. More solution would leave too
little air space to absorb shocks.
Damage to tyre could occur.
Tyre Size
Liquid Weight per tyre
kg (lb)—75% Full
6.00-16
30 (67)
LIQUID WEIGHT FOR REAR TYRES
With 0.6 kg/L (5 lb/gal) Calcium Chloride Solution
A solution of water and calcium chloride provides safe,
economical ballast. Used properly, it will not damage
tyres, tubes, or rims.
Use calcium chloride to prevent water from freezing. A
mixture of 0.6 kg per liter (5.0 lb of calcium chloride
per gal) will not freeze solid above —45°C (—53°F).
Tyre Size
Liquid weight per Tyre
kg (lb)—75% Full
12.4-28
216 (478)
13.6-28
237 (524)
14.9-28
339 (747)
PY80265,05GO878 –19–17JAN07–1/1
70-6
022607
PN=76
Wheels, Tyres and Treads
Service Tyres Safely
Explosive separation of at tyre and rim parts can cause
serious injury or death.
Do not attempt to mount a tyre unless you have the
proper equipment and experience to perform the job.
Always maintain the correct tyre pressure. Do not inflate
the tyres above the recommended pressure. Never weld
or heat a wheel and tyre assembly. The heat can cause
an increase in air pressure resulting in a tyre explosion.
Welding can structurally weaken or deform the wheel.
TS211
Check wheels for low pressure, cuts, bubbles, damaged
rims or missing lug bolts and nuts.
–UN–23AUG88
When inflating tyres, use a clip-on chuck and extension
hose long enough to allow you to stand to one side and
NOT in front of or over the tyre assembly. Use a safety
cage if available.
PY80265,05GO879 –19–10SEP05–1/1
Check Implement-to-Tyre Clearance
M47177
When large diameter rear tyres are
installed on a tractor with a 3-Point
Hitch, a quick coupler or similar device
may be required to provide adequate
implement-to-tyre clearance.
–UN–31JAN92
IMPORTANT: Check for adequate clearance (A)
between outside diameter of the tyre
and implement with hitch in raised
position.
A—Clearance
PY80265,05GO880 –19–10SEP05–1/1
75-1
022607
PN=77
Wheels, Tyres and Treads
Check Tyre Inflation Pressure
Check tyres daily for damage or noticeably low
pressure.
At least every 100 hours of operation, check inflation
pressure with a gauge. Use an accurate gauge having
10 kPa (0.1 bar) (1 psi) graduations.
If tyres contain liquid ballast, use a special air-water
gauge and measure with valve stem at bottom.
NOTE: When furrow plowing or during hillside
operation, tyre pressure can be increased 28
kPa (0.28 bar) (4 psi) ABOVE maximum to
prevent tyre wrinkling or buckling.
IMPORTANT: Always check inflation pressure with
an accurate tyre gauge to prevent
over-inflation. Over-inflation reduces
performance and increases strain of
both tyre and rim.
2. Operation of tyres at the inflation pressures listed
on chart will result in optimum tractive performance
of the tyre/vehicle system. Correctly inflated radial
tyres will show a large deflection of the sidewall or
“cheeks”. This is normal and will not hurt the tyre if
the inflation pressure is maintained.
3. Inflation pressures less than 80 kPa (12 psi) should
be monitored regularly because of the increased
risk of low pressure air leaks (especially due to
leaking valve cores).
4. Tractors operating on steep side slopes should
increase inflation pressures 28 kPa (4 psi) above
the values listed to compensate for lateral weight
transfer.
NOTE: Following inflation information applies to both
front and rear tyres and Tyre Inflation Pressure
Chart.
5. Tyres run as singles in high traction conditions
sometimes experience bead slip if the bead was not
fully seated or if too much lubricant was used to
mount the tyre. Increasing the inflation pressure will
compensate for this condition but will not cause
reduced traction. Consult your tyre dealer if this
problem occurs.
1. All inflation pressures are calculated for 29 km/h
(18 mph) travel speeds for both diagonal (bias) ply
and radial ply tyres.
6. If higher load capacities are needed, contact your
John Deere dealer for tyre manufacturers load and
inflation table information.
PY80265,05GO881 –19–09JAN07–1/1
75-2
022607
PN=78
Wheels, Tyres and Treads
Tyre Inflation Pressure Chart
Front Tyres
Tyre Size
With Maximum Ballast or Heavy
Mounted Implement
Ply Rating
Tread
kPa
(bar)
(psi)
kPa
(bar)
(psi)
8
F2
160
(1.6)
(23)
280
(2.8)
(40)
6.00-16
Rear Tyres
Tyre Size
With Little or No Added Weight
With Little or No Added Weight
With Maximum Ballast or Heavy
Mounted Implement
Ply Rating
Tread
kPa
(bar)
(psi)
kPa
(bar)
(psi)
12.4-28
12
R1
80
(0.8)
(12)
140
(1.4)
(20)
13.6-28
12
R1, R3, R4
90
(0.9)
(13)
120
(1.2)
(18)
14.9-28
12
R1
80
(0.8)
(12)
140
(1.4)
(20)
PY80265,05GO882 –19–17JAN07–1/1
Tighten Wheel/Axle Hardware Correctly
1. After driving tractor about 100 m (109 yd), and
before placing it under load, tighten hardware to
specified torque.
CAUTION: NEVER operate tractor with a
loose rim, wheel, hub, or axle.
Any time hardware is loosened, tighten to specified
torque.
2. Check hardware after working three hours and
again after 10 hours.
NOTE: Follow checking procedure when a new tractor
is first used, or wheels have been off.
3. Check all hardware frequently and keep it tight.
PY80265,05GO883 –19–10SEP05–1/1
Tighten Bolts— Front Axle
Tighten bolts in the following locations to specifications:
–UN–21JAN05
Specification
Front Axle—Axle-to-Knee Bolts—
Torque ......................................................................... 480 N•m (350 lb-ft)
Front Axle—Disk-to-Flange
Bolts—Torque .............................................................. 210 N•m (130 lb-ft)
PY4526
B—Disk-to-Flange
PY80265,05GO884 –19–10SEP05–1/1
75-3
022607
PN=79
Wheels, Tyres and Treads
Tighten Bolt Adjustable Front Axle––If
Equipped
PY5021
Specification
Adjustable Front Axle-to-Knee
Bolts—Torque ............................................................................... 480 N•m
Adjustable Front Axle
Disk-to-Flange Bolts—Torque ...................................................... 210 N•m
–UN–21MAY05
Tighten bolts in the following locations to specifications:
PY5844
–UN–21JUN06
A—Axle-to-Knee
B—Disk-to-Flange
NR25796,0000683 –19–15JAN07–1/1
75-4
022607
PN=80
Wheels, Tyres and Treads
Tighten Bolts—Rear Axle (M-14 Bolts)
Tighten bolts in the following locations to specifications:
–UN–06DEC04
Specification
Rear Axle Rim-to-Disk (Steel
Disk)—Torque.............................................................. 245 N•m (180 lb-ft)
Rear Axle Disk-to-Flange (Steel
Disk)—Torque.............................................................. 210 N•m (155 lb-ft)
PY1955
–UN–12JAN04
PY4282
A—Rim-to-Disk Bolts
B—Disk-to-Flange Bolts
C—M-14 Bolt
Current Arrangement with M-14 Bolt
PY80265,05GO885 –19–10SEP05–1/1
75-5
022607
PN=81
Wheels, Tyres and Treads
Tighten Bolts—Rear Axle (M-20 Stud)
Tighten bolts in the following locations to specifications:
–UN–06DEC04
Specification
Rear Axle Rim-to-Disk (Steel
Disk)—Torque.............................................................. 245 N•m (180 lb-ft)
Rear Axle Disk-to-Flange (Steel
Disk)—Torque.............................................................. 550 N•m (406 lb-ft)
PY1956
–UN–12JAN04
PY4282
A—Rim-to-Disk Bolts
B—Disk-to-Flange Bolts
C—Stud
D—Nut
New Arrangement with M-20 Stud and Nut
PY80265,05GO886 –19–10SEP05–1/1
M47179
IMPORTANT: Tyres must have at least 25 mm (1 in.)
clearance with fenders (A) and fuel
tank. When large diameter rear tyres are
installed, check clearance between tyre
and fenders and fuel tank.
–UN–31JAN92
Observe Rear Wheel Tread Width Limitations
PY80265,05GO887 –19–10SEP05–1/1
75-6
022607
PN=82
Wheels, Tyres and Treads
Tread Settings—Multi-Position Rear Wheels
Wheel tread on rear axle with multi-position wheels
can be adjusted by repositioning or exchanging the
rims or by reversing the wheel disks.
Wheel tread can also be adjusted by exchanging the
complete wheel to the opposite side of the tractor (This
maneuver permits the change from disk-dished-in to
disk-dished-out operations without disassembling the
wheel). When changing rear wheels from one side to
the other, the arrow on side wall of tyre points in the
direction of forward rotation.
Specification
Multi-Position Rear Wheels
Rim-to-Disk (Steel Disk)—
Torque................................................................... 245 N•m (180 lb-ft)
Multi-Position Rear Wheels
Disk-to-Flange (Steel Disk)—
Torque................................................................... 175 N•m (130 lb-ft)
NOTE: Tread settings are measured at bottom of
centerline.
STEEL DISKS
REAR TREAD WIDTH
Centerline-to-Centerline
The relationship of the wheel disk and rim in obtaining
the different tread settings is shown in the diagrams on
the facing page.
Diagram
Tyre Sizes
13.6-28
12.4-28
A study of these diagrams, before attempting to
change tread settings, will save unnecessary labor.
IMPORTANT: After setting wheel spacing, tighten
rim-to-disk and disk-to-flange bolts.
Drive tractor 100 m (109 yd) and
tighten again.
A
1417 mm (55.8 in.)
B
1513 mm (59.6 in.)
C
1617 mm (63.7 in.)
D
1716 mm (67.6 in.)
E
1820 mm (71.7 in.)
IN227
–UN–24MAY00
PY80265,05GO888 –19–10SEP05–1/2
PY80265,05GO888 –19–10SEP05–2/2
75-7
022607
PN=83
Wheels, Tyres and Treads
PY5021
LV1515
–UN–21MAY05
–UN–05MAR96
Tread Settings—Adjustable Front Axle––If Equipped
Front rims are offset. With some tires, this provides
two tread spacings, at each axle setting.
ADJUSTABLE FRONT AXLE TREAD SETTINGS
Diagram C
Centerline-to-centerline
Tread Positionª For 2 WD
Tire
1
2
3
4
5
6
7.5-16
1449 mm
(57.0 in.)
1549
(61.0 in.)
1649
(64.9 in.)
1749
(68.9 in)
1849
(72.8 in.)
1949
(76.7 in.)
6.0-16
1435 mm (56.5
in.)
1535 mm (60.4
in.)
1635 mm (64.4
in.)
1735 mm (68.3
in.)
1835 mm (72.2
in.)
1935 mm (76.2
in.)
ªTread position 1 is with axle adjustment at its most inward location. See adjust Front Axle Tread Width in this section.
ADJUSTABLE FRONT AXLE TREAD SETTINGS
Diagram D
Centerline-to-centerline
Tread Positionª
Tire
1
2
3
4
5
6
7.5-16
1583
(62.3 in.)
1683 mm
(66.3 in.)
1783 mm
(70.2 in.)
1883 mm
(74.1 in.)
1983 mm
(78.1 in.)
2083 mm
(82.0 in.)
ªTread position 1 is with axle adjustment at its most inward location. See adjust Front Axle Tread Width in this section.
NR25796,0000684 –19–15JAN07–1/1
75-8
022607
PN=84
Wheels, Tyres and Treads
PY5170
–UN–25AUG05
Checking Toe-In
A—Front Axle Toe-In Distance
1. Park machine on level surface.
2. Turn steering wheel so front wheels are in the
straight-ahead position. Stop engine.
6. Distance (A) at front of tyres should be 3—6 mm
less than distance measured at rear of tyres for
CARRARO front axle and 0—2 mm for DANA front
axle. Adjust toe-in if necessary. (See procedure in
this section.)
3. Measure distance (A) between tyres at hub level in
front of axle. Record measurement and mark the
tyres.
Toe-In Value Chart
4. Move tractor back about 1 m (3 ft), so mark is at
hub level behind the axle. Again, measure distance
between tyres at same point on tyre. Record
measurement.
Make
Toe-In Value
DANA FRONT AXLE
0-2 mm
CARRARO FRONT AXLE
3-6 mm
5. Determine the difference between front and rear
measurements. If the front measurement is smaller,
toe is “in”. If the rear is smaller, toe is “out”.
PY80265,05GO889 –19–10SEP05–1/1
75-9
022607
PN=85
Wheels, Tyres and Treads
Adjusting Toe-In
1. Loosen lock nut (A) on tie rod.
–UN–12JUN06
2. Adjust tie rod equally by rotating tube (B) to lengthen
or shorten tie rod. Adjust toe-in to 3 to 6 mm for
CARRARO front axle and 0—2 mm for DANA front
axle.
PY4882
3. Tighten bolt to specification. Do not overtighten as
damage to the tube may occur.
.
Specification
Tie Rod Jam Nut—Torque .............................................. 90 N•m (66 lb-ft)
Powered Axle
Make
Toe-In Value
DANA FRONT AXLE
0-2 mm
CARRARO FRONT AXLE
3-6 mm
–UN–26AUG04
Toe-In Value Chart
PY4148
A—Tie Rod Lock Nut
B—Tie Rod Tube
Non-Powered Axle
PY80265,05GO890 –19–04JUL06–1/1
75-10
022607
PN=86
Wheels, Tyres and Treads
Adjusting Toe-In - Adjustable Front Axle––IF
Equipped
1. Loosen locker nuts (A) on locker (B).
2. Loose ball joint lock nut (E).
–UN–25MAY05
3. Adjust tie rods on both sides of the tractor equally by
the extensioner to lengthen or shorten. Adjust toe-in to
3 to 6 mm (1/8 to 1/4 in.)
PY5025
4. Tighten nut on locker (A) to specification.
Specification
Locker Nut—Torque ...................................................................... 40 N•m
5. Tighten the ball joint lock nuts (E) to specification.
Specification
Extensioner Lock Nut—Torque ................................................... 160 N•m
A—Locker Nut
B—Locker
C—Tie Rod
D—Extensioner
E—Lock Nut
NR25796,0000686 –19–15JAN07–1/1
75-11
022607
PN=87
Transporting
Use Safety Lights and Devices
Prevent collisions between other road users, slow moving
tractors with attachments or towed equipment, and
self-propelled machines on public roads. Frequently check
for traffic from the rear, especially in turns, and use hand
signals or turn signal lights.
TS951
–UN–12APR90
Use headlights, flashing warning lights, and turn signals
day and night. Follow local regulations for equipment
lighting and marking. Keep lighting and marking visible
and in good working order. Replace or repair lighting and
marking that has been damaged or lost.
PY80265,05GO891 –19–10SEP05–1/1
Driving Tractor on Roads
–UN–12JUN06
CAUTION: Observe the following precautions
when operating on a road.
PY5017
1. Before operating tractor on highway be sure tail lights
(A) and flashing turning lights (B) work properly. Install
and use auxiliary lighting to equipment as required for
safety and by local regulations.
For 5103E Tractor
PY5029
–UN–12JUN06
A—Tail light
B—Turning Lights
C—Reflex Reflector
For 5103, 5103S, 5203, 5104 and 5204 Tractor
Continued on next page
80-1
NR25796,0000353 –19–11JAN07–1/5
022607
PN=88
Transporting
CAUTION: NEVER operate flood lampwhen
transporting tractor. Clear bright light at the
rear of the tractor could confuse drivers of
other vehicles as they approach from the rear.
–UN–23FEB06
IMPORTANT: Refer to Lights section for detailed
descriptions of lighting operations and
functions.
PY4106
2. Turn light switch to high beam headlights or low beam
headlights position. Never use bright lights which are
visible from the rear. Always dim headlights before
meeting another vehicle. Keep headlights properly
adjusted.
A—Lights OFF
B—Parking Lights
C—Dim Headlights
D—Bright Headlights
E—High Beamlight
NR25796,0000353 –19–11JAN07–2/5
3. Use turn signals when turning. Be sure to return turn
signal lever (A) to center position after turning.
PY4114
–UN–23FEB06
A—Turn Signal Lever
NR25796,0000353 –19–11JAN07–3/5
4. Couple brake pedals (A) together before driving on a
road. Avoid hard applications of brakes.
–UN–06AUG06
5. Drive slowly enough to maintain safe control at all
times. Slow down for hillsides, rough ground, and
sharp turns, especially when transporting heavy,
rear-mounted equipment.
PY6098
6. Before going down a hill, shift to a gear low enough to
control speed without using brakes. Never coast down
hill.
Brake Pedals
7. When transporting downhill on icy or graveled grades,
be alert for skids which could result in loss of steering
control. To decrease chance of skids, reduce speed
and be sure tractor has proper ballast.
A—Brake Pedals
Continued on next page
80-2
NR25796,0000353 –19–11JAN07–4/5
022607
PN=89
Observe these recommended maximum road
speeds, or local speed limits which may be
lower:
If towed equipment does not have brakes, do
not travel more than 32 km/h (20 mph) and do
not tow loads more than 1.5 times the tractor
weight.
LV4042
CAUTION: Stopping distance increases with
speed and weight of towed loads, and on
slopes. Towed loads with or without brakes that
are too heavy for the tractor or are towed too
fast can cause loss of control. Consider the
total weight of the equipment and its load.
–UN–09JUL99
Transporting
If towed equipment has brakes, do not travel
more than 40 km/h (25 mph) and do not tow
loads more than 4.5 times the tractor weight.
Ensure the load does not exceed the
recommended weight ratio. Add ballast to
recommended maximum for tractor, lighten the
load, or get a heavier towing unit. The tractor
must be heavy and powerful enough with
adequate braking power for the towed load. Use
additional caution when towing loads under
adverse surface conditions, when turning, and
on inclines.
8. Use caution when operating tractor at transport
speeds. Reduce speed if towed load weighs more than
tractor and is not equipped with brakes. (See Towed
Equipment operator’s manual for recommended
transport speeds.)
9. Use additional caution when transporting towed loads
under adverse surface conditions, when turning and on
inclines.
10. Heavy towed or rear mounted implements may start
swaying in transport. Excessive swaying will result in
loss of steering control. Drive slowly and avoid quick
turns of steering wheel. Refer to your implement
operator’s manual regarding maximum travel speed
limitations.
NR25796,0000353 –19–11JAN07–5/5
80-3
022607
PN=90
Transporting
Transport on Carrier
CAUTION: Chain tractor to carrier securely.
Drive carrier slowly.
–UN–22APR94
The best method of transporting a disabled tractor is to
haul it on a flatbed carrier.
LV610
IMPORTANT: Seal exhaust to prevent dirt from
entering and damaging engine.
PY80265,05GO893 –19–10SEP05–1/1
Towing Tractor
–UN–12JUN06
CAUTION: NEVER tow tractor faster than 16
km/h (10 mph). Have an operator steer and
brake tractor.
1. Be sure transmission-hydraulic system oil is to the full
level line on sight gauge (A). If the tractor is to be
towed with the front wheels raised, add 1 liter of oil to
hydraulic fill port (C) for each 90 mm (3-1/2 in.) the
wheels are raised. DO NOT raise front wheels more
than 305 mm (12 in.) above ground.
PY4143
IMPORTANT: To avoid damaging
transmission-hydraulic system, observe
the following precautions:
For 5103E Tractor
–UN–12DEC05
NOTE: After transporting tractor, drain oil that was added
for towing.
2. Make sure the differential lock is disengaged.
PY4142
3. Make sure range lever is in neutral and gear lever is in
4th gear.
For 5103, 5103S, 5203, 5104 and 5204 Tractor
A—Full Level Mark
B—Low Level Mark
C—Hydraulic Oil Filler Port
NR25796,0000354 –19–12JAN07–1/1
80-4
022607
PN=91
Fuels, Lubricants and Coolant
Handle Fuel Safely—Avoid Fires
Use only diesel fuel.
–UN–09MAR90
Handle fuel with care, it is highly flammable.
DO NOT refuel machine:
M73115
• While you smoke.
• When machine is near open flame or sparks.
• When engine is running. STOP engine.
Fill fuel tank outdoors.
Help prevent fires:
• Clean oil, grease and dirt from machine.
• Clean up spilled fuel immediately.
Do not store machine with fuel in tank in a building where
fumes may reach an open flame or spark.
PY80265,05GO895 –19–10SEP05–1/1
Handle Fluids Safely—Avoid Fires
Store flammable fluids away from fire hazards. Do not
incinerate or puncture pressurized containers.
Make sure machine is clean of trash, grease, and debris.
TS227
Do not store oily rags; they can ignite and burn
spontaneously.
–UN–23AUG88
When you work around fuel, do not smoke or work near
heaters or other fire hazards.
PY80265,05GO896 –19–10SEP05–1/1
85-1
022607
PN=92
Fuels, Lubricants and Coolant
Fuel Storage
Buy good quality, clean fuel from a reputable supplier.
Avoid storing fuel over long periods of time.
Proper fuel storage is critically important. Use clean
storage and transfer tanks. Periodically drain water
and sediment from bottom.
Store fuel in a convenient place away from buildings.
PY80265,05GO897 –19–10SEP05–1/1
Diesel Fuel
Fuel sulphur content should be less than 1.0 percent
preferably less than 0.5 percent. Diesel fuel having
sulphur content higher than 1.0 percent may cause
increase wear on metal engine parts because of acids
produced by sulphur during combustion.
Cetane number should be no less than 40 to assure
satisfactory starting and overall performance.
Fitleration of fuel is critical for proper operation of
engine. Use genuine MICO fuel filters. Alwasy change
fuel filter insert at given interval
IMPORTANT: If fuel sulphur content exceeds 0.7
percent, the engine oil drain interval
must be reduced by 50 percent to
125 hours.
PY80265,05GO898 –19–10SEP05–1/1
Diesel Fuel Filters
PY4145
–UN–26AUG04
Fitleration of fuel is critical for proper operation of engine.
Use genuine MICO fuel filters. Alwasy change fuel filter
inserts (primary and seconary)at given interval
.
PY80265,05GO899 –19–10SEP05–1/1
85-2
022607
PN=93
Fuels, Lubricants and Coolant
Fill Fuel Tank
–UN–23AUG88
CAUTION: Handle fuel with care: It is highly
flammable. DO NOT refuel the machine while
smoking or when near open flame or sparks.
Always stop engine before refueling machine.
Fill fuel tank outdoors.
TS202
Prevent fires by keeping machine clean of
accumulated trash, grease and debris. Always
clean up spilled fuel.
Fuel tank can be filled through either fill cap (A). Fill fuel
tank at end of each days operation. This prevents
condensation in tank as moist air cools.
–UN–27MAY05
Specification
Fuel Tank (5103, 5103S, 5203,
5104 and 5204 Tractor)—
Capacity .............................................................................................. 62 lit
Fuel Tank (5103E Tractor)—
Capacity .............................................................................................. 50 lit
PY5027
A—Fuel Tank Filler Cap
PY4101
–UN–20AUG04
For 5103, 5103S, 5203, 5104 and 5204 Tractor
For 5103E Tractor
PY80265,05GO901 –19–29DEC06–1/1
85-3
022607
PN=94
Fuels, Lubricants and Coolant
Lubricant Storage
Your equipment can operate at top efficiency only
when clean lubricants are used.
Make certain that all containers are properly marked to
identify their contents.
Use clean containers to handle all lubricants.
Properly dispose of all old containers and any residual
lubricant they may contain.
Whenever possible, store lubricants and containers in
an area protected from dust, moisture, and other
contamination. Store containers on their side to avoid
water and dirt accumulation.
PY80265,05GO902 –19–10SEP05–1/1
Diesel Engine Oil
PY5826
–UN–20JUN06
Use genuine engine oil. This oil is available in pack of
1litre and 8.5 litre at John Deere Dealership only
PY80265,05G1309 –19–20JUN06–1/1
85-4
022607
PN=95
Fuels, Lubricants and Coolant
Diesel Engine Coolant
The engine cooling system is filled to provide
year-round protection against corrosion and cylinder
liner pitting, and winter freeze protection to -37°C
(-34°F). If protection at lower temperatures is required,
consult your John Deere dealer for recommendations.
John Deere COOL-GARD Prediluted Coolant is
preferred for service.
John Deere COOL-GARD Prediluted Coolant is
available in a concentration of either 50% ethylene
glycol or 55% propylene glycol.
Additional recommended coolants
The following engine coolant is also recommended:
• John Deere COOL-GARD Coolant Concentrate in a
40% to 60% mixture of concentrate with quality
water.
John Deere COOL-GARD coolants do not require use
of supplemental coolant additives, except for periodic
replenishment of additives during the drain interval.
Other fully formulated coolants
Other fully formulated low silicate ethylene or
propylene glycol base coolants for heavy-duty engines
may be used if they meet one of the following
specifications:
• ASTM D6210 prediluted (50%) coolant
• ASTM D6210 coolant concentrate in a 40% to 60%
mixture of concentrate with quality water
Coolants meeting ASTM D6210 do not require use of
supplemental coolant additives, except for periodic
replenishment of additives during the drain interval.
Other low silicate ethylene glycol base coolants for
heavy-duty engines may also be used if they meet one
of the following specifications:
• ASTM D4985 ethylene glycol base prediluted (50%)
coolant
• ASTM D4985 ethylene glycol base coolant
concentrate in a 40% to 60% mixture of concentrate
with quality water
Coolants meeting ASTM D4985 require an initial
charge of supplemental coolant additives, formulated
for protection of heavy duty diesel engines against
corrosion and cylinder liner erosion and pitting. They
also require periodic replenishment of additives during
the drain interval.
Other coolants
It is possible that neither John Deere COOL-GARD nor
coolants meeting one of the coolant standards listed
above is available in the geographical area where
service is performed. If these coolants are unavailable,
use a coolant concentrate or prediluted coolant with a
quality additive package that provides cylinder liner
cavitation protection and protects the cooling system
metals (cast iron, aluminum alloys, and copper alloys
such as brass) from corrosion.
The additive package must be part of one of the
following coolant mixtures:
• ethylene glycol or propylene glycol base prediluted
(40% to 60%) coolant
• ethylene glycol or propylene glycol base coolant
concentrate in a 40% to 60% mixture of concentrate
with quality water
Water quality
Coolants requiring supplemental coolant additives
COOL-GARD is a trademark of Deere & Company
Continued on next page
85-5
DX,COOL3 –19–27OCT05–1/2
022607
PN=96
Fuels, Lubricants and Coolant
Water quality is important to the performance of the
cooling system. Distilled, deionized, or demineralized
water is recommended for mixing with ethylene glycol
and propylene glycol base engine coolant concentrate.
IMPORTANT: Do not mix ethylene glycol and
propylene glycol base coolants.
IMPORTANT: Do not use cooling system sealing
additives or antifreeze that contains
sealing additives.
DX,COOL3 –19–27OCT05–2/2
Use Correct Transmission-Hydraulic Filter
Element
To protect systems, replace transmission-hydraulic oil filter
with a John Deere service filter element. Minimum and
maximum performance specifications are printed on John
Deere filters. Other filters may be used if they meet these
performance specifications.
See Lubrication and Maintenance section for
recommended filter change intervals.
PY80265,05GO905 –19–10SEP05–1/1
Transmission and Hydraulic Oil
PY5827
–UN–20JUN06
Same oil is used for transmission and hydraulic. Use
HY-GARD transmission-hydraulic oil. This oil is available
in pack of 1 litre and 20 litre at John Deere Dealership
only
HY-GARD is a trademark of Deere & Company
PY80265,05GO906 –19–20JUN06–1/1
85-6
022607
PN=97
Fuels, Lubricants and Coolant
Grease
Depending upon the expected air temperature range
during the service interval, use grease as shown on
the adjoining table.
At temperatures below —30°C (—22°F), use arctic
greases such as those meeting Military Specification
MIL-G-10942C.
Grease Type
John Deere
High-Temperature/Extreme-Pressure/Non-Clay Grease
is recommended.
Arctic Grease
If other greases are used, they must be greases
meeting SAE Multipurpose High Temperature Grease
with Extreme Pressure (EP) Performance and capable
of operating at compartment temperatures above
150°C (302°F)
Temperature Limits
Below —10°C (14°F)
SAE (NLGI) #0 or #1
0°C to —30°C (32°F to —22°F)
SAE (NLGI) #2
50°C to 0°C (122°F to 32°F)
JD High Temperature
50°C to —10°C (122°F to 14°F)
PY80265,05GO907 –19–10SEP05–1/1
85-7
022607
PN=98
Service and Maintenance
Observe Service Intervals
–UN–31MAY06
Using hour meter (A) as a guide, perform all services at
the hourly intervals indicated on the following pages. Keep
a service record on charts provided in the Lubrication and
Maintenance Record Charts section.
PY5737
IMPORTANT: Recommended service intervals are for
average conditions. Service MORE
OFTEN if tractor is operated under
adverse conditions.
For 5103, 5103S, 5203, 5104 and 5204 Tractor
PY5761
–UN–01JUN06
A—Hour Meter
For 5103E Tractor
PY80265,05GO908 –19–29DEC06–1/1
Break-In Service
IMPORTANT: Keep wheel hardware tight to avoid
tractor damage. Check wheel
hardware torque before operating,
twice during first ten hours of
operation, after fifty hours of
operation, and periodically
thereafter.
Tighten wheel hardware. (See Wheels, Tyres, and
Treads section.)
During the First 10 Hours of Operation:
After the First 100 Hours of Operation:
Perform daily or 10 hours service. (See Service
Intervals in Lubrication and Maintenance section.)
Replace transmission-hydraulic filter element
Check alternator/fan belt tension and tighten air intake
and cooling system hose clamps
Perform 50 Hours Service
Change engine oil and filter1
Tighten wheel hardware. (See Wheels, Tyres, and
Treads section.)
After the First 1100 Hours of Operation
After the First 50 Hours of Operation:
Change transmission-hydraulic oil and filter
1
See Engine Break-In Oil in Service section for additional
information.
NR25796,0000236 –19–21JUN06–1/1
90-1
022607
PN=99
Service and Maintenance
Continued on next page
90-2
PY5833
–UN–26FEB07
Service Intervals
NR25796,00002C5 –19–26FEB07–1/3
022607
PN=100
Service and Maintenance
Every 10 Hours
•
•
•
•
•
•
•
•
•
Check engine oil level
Check coolant level
Drain water and sediment from fuel filter
Lubricate tie rod ends1
Lubricate steering spindles1
Lubricate front axle pivot pin(s)1
Lubricate rear axle bearings1
Lubricate clutch pedal and right hand brake pedal.1
Lubricate cluch / brake shaft.1
• Check brake pedal adjustment
• Replace filter inserts ( primary and secondary
alternatively)
IMPORTANT: Never replace primary and
secondary inserts simultaneously
Every 500 Hours
• Replace transmission-hydraulic filter
Every 600 Hours
IMPORTANT: External lubrication is not required
for oil type rear axle
Every 50 Hours
•
•
•
•
•
•
•
•
Check transmission-hydraulic system oil level
Clean and check battery
Inspect all tires
Lubricate front axle pivot pin(s)
Lubricate steering spindles
Inspect tractor for loose nuts and bolts
Lubricate clutch pedal and right hand brake pedal.
Lubricate clutch / brake shaft.
•
•
•
•
•
•
•
Clean engine crankcase vent tube
Repack front wheel bearings
Check and tighten all hoses and hose clamps
Check cooling system for leaks
Lubricate rear axle bearings
Check engine idle speeds
Have your John Deere dealer:
-Check front axle pivot pin
-Adjust engine valve clearance
Inspect fuel injectors
IMPORTANT: External lubrication is not required
for oil type rear axle
First 100 Hours
• Change engine oil and filter
• Replace transmission-hydraulic filter
First 1100 Hours
• Change transmission-hydraulic oil and filter
Every 250 Hours
Every 1250 Hours
•
•
•
•
•
•
•
• Change transmission-hydraulic oil and filter
• Clean transmission-hydraulic pickup screen
Service air cleaner
Change engine oil and filter
Clean and check battery
Inspect and adjust alternator/fan belt
Lubricate 3-point hitch
Check neutral start system
Check clutch pedal free travel
Annually
• Change engine oil and filter
• Replace air cleaner elements
1
Only necessary when operating in extremely wet and muddy
conditions.
Continued on next page
90-3
NR25796,00002C5 –19–26FEB07–2/3
022607
PN=101
Service and Maintenance
Every 2 Years or 2000 Hours (Whichever Comes
First)
• Flush cooling system
• Service air cleaner
• Adjust throttle friction
• Drain water and sediment from fuel tank and fuel
filter
Service As Required
NR25796,00002C5 –19–26FEB07–3/3
90-4
022607
PN=102
Service—Every 10 Hours
Check Engine Oil Level
2. Pull out dipstick (A). Oil level should be between two
marks on dipstick. DO NOT operate engine when oil
level is below “LOW” mark on dipstick.
PY4036
3. If level is low, add oil through oil filler port (B) until
even with upper mark. DO NOT overfill. (See fuels,
Lubricants, Coolants and filters section.)
–UN–19JUN06
1. Park tractor on level ground, put range shift lever in
neutral (N), set brakes and turn engine “OFF”.
A—Engine Oil Dipstick
B—Engine Oil Filler Port
PY80265,05GO911 –19–07NOV06–1/1
Check Coolant Level
1. Check coolant level in coolant recovery tank (A).
2. Coolant level shall be upto to “Cold Mark”. If it is below
“Cold Mark”, add coolant to that mark only. (See Fuels,
Lubricants and Coolant section.)
TS281
IMPORTANT: Check the coolant level when engine is
cold.
–UN–23AUG88
CAUTION: . Only remove radiator cap (B) when
engine is cold. Slowly loosen cap to first stop
to relieve pressure before removing completely.
PY4121
–UN–07DEC05
A—Coolant Recovery Tank
B—Radiator Cap
PY80265,05GO912 –19–04JUL06–1/1
95-1
022607
PN=103
Service—Every 10 Hours
Drain Water and Sediment From Fuel Filter
NOTE: Place a small container under drain fitting to catch
draining fuel. Dispose of waste properly.
–UN–23AUG05
1. Put range shift lever in neutral (N), set brakes and turn
engine OFF.
PY5162
2. Open fuel filter drain Plug (A) to bleed accumulated
moisture and sediment from filter into container.
Tighten drain plug when clear fuel runs from drain.
A—Fuel Filter Drains
PY80265,05GO913 –19–07NOV06–1/1
Lubricate as Necessary
Lubrication required only when operating in extremely
wet and muddy conditions. Lubricate with several
shots of multipurpose grease specified in Fuels,
Lubricants and Coolant section.
• Rear axle bearings (See Service—600 Hours)
• Tie rod ends
• Steering spindles (Front Axle) (See Service—50
Hours)
• Front axle pivot pin(s) (See Service—50 Hours)
• Lubricate clutch pedal and right hand brake pedal
(See Service—50 Hours)
• Lubricate cluch / brake shaft. (See Service—50
Hours)
IMPORTANT: External lubrication is not required
for oil type rear axle.
NR25796,00002C6 –19–25JUL06–1/1
95-2
022607
PN=104
Service—Every 50 Hours
Check Transmission-Hydraulic System Oil
Level
–UN–12JUN06
1. Park on level ground. Put range shift lever in neutral
(N), set brakes and turn engine OFF.
2. Wait a minimum of five minutes for oil to settle.
4. Add oil to filler port (C) if level is low. (See Anti-Chatter
Transmission/Hydraulic Oil in Fuels, Lubricants and
Coolant section.)
PY4143
3. Check level at sight glass. Level should be to full oil
level mark (A).
For 5103E Tractor
PY4971
–UN–10DEC05
A—Hydraulic Oil Full Level Mark
B—Hydraulic Oil Low Level Mark
C—Hydraulic Oil Filler Port
For 5103, 5103S, 5203, 5104 and 5204 Tractor
NR25796,000025E –19–29DEC06–1/1
Clean and Check Battery
To access battery, see procedure in Service section.
PY4018
–UN–10DEC05
Put range shift lever in neutral (N), set brakes and turn
engine OFF. Wipe battery with a damp cloth. Clean and
tighten connections if needed. Check fluid level in each
cell, fill to bottom of filler neck with clean mineral-free
water. (See Servicing Battery in Service section.)
A—Positive Terminal
B—Negative Terminal
PY4102
–UN–10DEC05
For 5103, 5103S, 5203, 5104 and 5204 Tractor
For 5103E Tractor
NR25796,000025F –19–12JAN07–1/1
100-1
022607
PN=105
Service—Every 50 Hours
Lubricate Front Axle Pivot Pin
–UN–26AUG04
Front axle pivot pin (A) requires lubrication of the front
and rear pivot bushing zerks with multipurpose grease.
(See Fuels, Lubricants and Coolant section).
PY4146
A—Front Axle Pivot Pin
NR25796,0000260 –19–12JUL06–1/1
On front axle, apply several shots of general purpose
grease to steering spindle fitting (A). (See Fuels,
Lubricants and Coolant section) As Dana make front axle
comes with self lubricating bearings, there is no need of
spindle lubrication.
PY4144
A—Greasing point
–UN–26AUG04
Lubricate Steering Spindles
NR25796,0000261 –19–12JUL06–1/1
100-2
022607
PN=106
Service—Every 50 Hours
Lubricate Clutch Pedal and Brake Pedal
Lubricate clutch pedal with multipurpose grease at
greasing point (A).
–UN–25JUL06
Lubricate brake pedals with multipurpose grease at
greasing point (B).
PY5993
Also lubricate clutch and brake shaft at the same time.
A—Clutch Pedal Greasing Points
B—Brake Pedal Greasing Points
PY5992
–UN–25JUL06
Clutch Pedal Lubrication
Brake Pedal Lubrication
NR25796,00002C9 –19–25JUL06–1/1
100-3
022607
PN=107
Service—Every 50 Hours
PY6099
–UN–06AUG06
Inspect Tyres and Loose Hardwares
NOTE: Tractor shown may have optional equipment.
Inspect all tyres and check inflation pressure. Also
check tractor for any loose harware
Item
Measurement
Specification
Ballast Weights Retaining Bolts
Torque
Front Axle Disk-to-Flange Bolts
Torque
210 N•m (155 lb-ft)
Rear Axle Rim-to-Disk Bolts
Torque
245 N•m (180 lb-ft)
Rear Axle Disk-to-Flange Bolts
Torque
(5103, 5103S, 5203, 5104 and 5204)
550 N•m (406 lb-ft)
Rear Axle Disk-to-Flange Bolts (5103 Torque
E)
210 N•m (155 lb-ft)
230 N•m (170 lb-ft)
NR25796,0000355 –19–12JAN07–1/1
100-4
022607
PN=108
Service—Every 250 Hours
Change Engine Oil and Filter
1. Run engine to heat oil. Turn engine off.
2. Remove oil drain plug (A) and drain oil.
PY4147
–UN–26AUG04
3. Replace engine oil filter (B) while changing oil. Apply a
film of oil on the new oil filter gasket and install new
filter. Hand tighten plus 1/2 turn.
4. Install drain plug.
5. Add seasonal viscosity grade oil. (See Fuels,
Lubricants and Coolant section.)
A—Engine Oil Drain Plug
B—Engine Oil Filter
Specification
Engine Crankcase Oil—Capacity ....................................................... 8.5 L
NOTE: In Break-in-period, change the oil in first 100
hours.
PY80265,05GO920 –19–10SEP05–1/1
Service Air Cleaner
–UN–03SEP04
A dual element air cleaner is standard. A dirty primary
element is indicated when the air restriction indicator on
instrument panel illuminates. A dirty element can result in
loss of power or excessive smoke.
Service air cleaner (A) when indicator light illuminates,
every 250 hours or at least once a year.
PY4179
IMPORTANT: Check unloader valve (B) frequently.
Empty as often as needed to keep it
from filling with dust. If valve is allowed
to fill with dust, air cleaner element will
plug rapidly.
A—Air Cleaner
B—Dust Unloader Valve
Replace primary element at least one a year.
The secondary element should be removed only when
being replaced, normally once a year.
See procedure in Removing Air Cleaner Elements in
Service section.
PY80265,05GO921 –19–10SEP05–1/1
110-1
022607
PN=109
Service—Every 250 Hours
Replace Fuel Filter Inserts
1. Remove cap screw (A) and filter element bowl (B).
2. Take out filter insert (C).
3. Drain the fuel and clean the bowl.
4. Install new filter insert.
5. Reinstall the bowl (B) and tighten screw (A) and
washer (D).
–UN–18APR05
6. Bleed the system from bleed screw (E).
PY4917
IMPORTANT: Change primary and secondary filter
inserts alternatively. Never change both
filter inserts simultaneously. Always
use new O-ring which comes filter
inserts.
A—Cap Screw
B—Filter Element Bowl
C—Filter Insert
D—Washer
E—Bleed Screw
PY80265,05GO922 –19–04JUL06–1/1
Inspect and Adjust Alternator/Fan Belt
Replace if worn or damaged. (See procedure in Service
section.)
–UN–27OCT03
NOTE: Run engine for five minutes to warm a cold belt.
Let a hot belt cool for 15 minutes before
adjustment.
Adjust tension by loosening cap screw (A) and mounting
bolt (B). Apply force to alternator frame (C) until belt
tension is correct. Tighten cap screw and bolt.
PY1652
Check tension by pressing belt midway between pulleys.
Belt should deflect about 19 mm (3/4 in.) at 89 N (20 lb
force).
A—Tension Adjustment Cap Screw
B—Alternator Mounting Bolt
C—Alternator Frame
PY80265,05GO923 –19–10SEP05–1/1
110-2
022607
PN=110
Service—Every 250 Hours
Lubricate 3-Point Hitch
–UN–12JUN06
Lubricate right lift link (A) and left lift link (B) with several
shots of multipurpose grease. (See Fuels, Lubricants and
Coolant section.)
PY4972
A—Right Lift Link Grease Fittings (2 used)
B—Left Lift Link Grease Fitting
PY5389
–UN–10DEC05
For 5103, 5103S, 5203, 5104 and 5204 Tractor
For 5103E Tractor
PY80265,05GO924 –19–29DEC06–1/1
CAUTION: If starter turns engine in any of the
following steps, have the neutral start system
repaired by your John Deere dealer.
PY5390
• Range shift lever (A) in NEUTRAL
• PTO lever (B) in disengaged position
Dual Clutch Tractor
PY5391
–UN–10DEC05
Your John Deere tractor is equipped with interlocks to
prevent inadvertent movement when the engine is started.
Turning the key switch with the clutch pedal depressed
should crank the engine if all of the following conditions
exist:
–UN–10DEC05
Check Neutral Start System
Single Clutch Tractor
A—Range Shift Lever
B—PTO Control Lever
Turning the key switch to the start position should NOT
start the engine, if either of the following exist:
• Range shift lever (A) in gear (not in NEUTRAL)
• PTO lever (B) in engaged position
PY80265,05GO925 –19–10SEP05–1/1
110-3
022607
PN=111
Service—Every 250 Hours
Check and Adjust Clutch Pedal Free Play
Measure free play (A) at top of pedal stroke. Adjust
linkage to obtain 20 to 25 mm free play.
A—Clutch Pedal Free Play
B—Lock Nut
C—Cotter Pin
D—Washer
E—Retaining Pin
PY6100
–UN–06AUG06
To adjust linkage, loosen lock nut (B), remove cotter pin
(C), washer (D) and retaining pin (E). Rotate clevis. After
making adjustment, replace clip, pin and washer and
check free play. When free play is correct, tighten lock
nut.
PY4976
–UN–25APR05
Clutch Pedal Free Play
NR25796,0000356 –19–07AUG06–1/1
110-4
022607
PN=112
Service—Every 250 Hours
PY5828
–UN–20JUN06
Check and Adjust Brake Pedal Free Play
1. Park on level surface. Chock wheels to prevent
machine movement.
2. Unlock brake pedals.
–UN–06AUG06
3. Check free play (A) of each brake pedal at top of
stroke.
PY6100
4. Linkage must be to specification.
Specification
Brake Pedal—Free Play ................................................................. 60 mm
Brake Pedal Adjustment
5. To adjust linkage, loosen jam nut (C).
A—Brake Pedal Free Play
B—Clip Pin
C—Jam Nut
D—Arm
E—Yoke
6. Remove clip pin (B) from yoke (E) on either end of
linkage.
7. Turn arm (D) until free play is to specification.
8. Tighten jam nut.
9. Install clip pin.
NR25796,0000357 –19–04AUG06–1/1
110-5
022607
PN=113
Service—Every 500 Hours
Replace Transmission-Hydraulic Filter
1. Remove filter (A). Apply a film of oil to new gasket and
install new filter. Hand tighten plus 1/2 turn.
–UN–06AUG06
2. Run engine several seconds and recheck
transmission-hydraulic oil level.
PY6081
3. Add transmission-hydraulic oil if required (See Fuels,
Lubricants and Coolant section).
A—Transmission-Hydraulic Oil Filter
Right Side of Transmission
NR25796,0000350 –19–04AUG06–1/1
112-1
022607
PN=114
Service—Every 600 Hours
Clean Engine Crankcase Vent Tube
CAUTION: Reduce compressed air to less than
210 kPa (2 bar) (30 psi) when using for cleaning
purposes. Clear area of bystanders, guard
against flying chips, and wear personal
protection equipment including eye protection.
–UN–21JAN05
Remove crankcase vent tube (A) from engine. Wash in
solvent or blow clean with compressed air. Reassemble
vent tube breather cap to engine. Be sure vent tube is not
kinked or pinched.
PY4527
A—Crankcase Vent Tube
PY80265,05GO929 –19–10SEP05–1/1
Pack Front Wheel Bearings (Only For Carraro
Front Axle)
1. Jack up front end of tractor..
–UN–22JAN05
2. Remove hub cap, cotter pin, and wheel nut.
PY4529
3. Remove washer and wheel bearings. Clean all parts in
solvent and blow dry with compressed air. Replace any
worn or damaged parts.
4. Pack bearing with multipurpose grease. (See Fuels,
Lubricants and Coolant section.) Coat seal with same
grease.
5. Reinstall bearings, washer, and wheel nut.
–UN–22JAN05
6. Tighten wheel nut until a slight drag is felt when hub is
turned. Back nut off just enough to install cotter pin in
hole in wheel spindle.
IMPORTANT: DANA Front Axle: No need to grease
Hub Assembly because it is provided
with Self-Lubricated bearings.
PY4528
7. Reinstall hub cap and wheels. Tighten lug bolts to 175
N•m (130 lb-ft). Retighten bolts after driving tractor 100
m (109 yds) and again after 3 hours and 10 hours use.
A—Hub Cap
B—Pack Bearing with Grease
PY80265,05GO930 –19–10SEP05–1/1
115-1
022607
PN=115
Service—Every 600 Hours
Radiator Lower Hose
PY4155
PY4156
–UN–28AUG04
–UN–28AUG04
PY4116
PY4115
–UN–21AUG04
–UN–21AUG04
Check Hoses and Hose Clamps for Tightness
Radiator Upper Hose
Check the following systems hose clamps for tightness:
Air Cleaner to engine intake
Engine Cooling
Hydraulics
Fuel
–UN–27AUG04
•
•
•
•
PY4154
Check all hoses for cracks which could cause leaks or
possible failure. Replace as necessary.
A—Hose Clip
PY80265,05GO931 –19–04JUL06–1/1
115-2
022607
PN=116
Service—Every 600 Hours
Lubricate Rear Axle Bearings
–UN–16JUL04
Lubricate rear axle fittings (A), both sides, with several
shots of multi-purpose grease. (See Fuels, Lubricants and
Coolant section.)
PY4025
IMPORTANT: External lubrication is not required for
oil type rear axle.
A—Rear Axle Fitting (2 used)
PY1707
–UN–03NOV03
Rear Axle Fitting ( Dry Land)
Rear Axle Fitting ( Wet Land)
NR25796,00002C7 –19–25JUL06–1/1
115-3
022607
PN=117
Service—Every 600 Hours
Check Engine Idle Speeds
For 5103E, 5103, 5103S and 5203 Tractors
Slow idle speed is 850 ± 25rpm.
–UN–31MAY06
With no load, fast idle speed is 2485 ± 25 rpm.
Specification
Engine—Slow Idle—Speed .................................................. 850 ± 25 rpm
Engine—Fast Idle (with No
Load)—Speed.................................................................... 2485 ± 25 rpm
PY5734
If idle speeds are not correct, see your John Deere
dealer.
For 5103, 5103S, 5203, 5104 and 5204 Tractor
For 5104 and 5204 Tractors
Slow idle speed is 800 - 875 rpm.
–UN–01JUN06
With no load, fast idle speed is 2475 - 2550 rpm.
Specification
Engine—Slow Idle—Speed ................................................. 800 - 875 rpm
Engine—Fast Idle (with No
Load)—Speed................................................................. 2475 - 2550 rpm
PY5758
If idle speeds are not correct, see your John Deere
dealer.
For 5103E Tractor
PY80265,05GO933 –19–29DEC06–1/1
Check Front Axle Pivot Pin
–UN–26AUG04
Ask your John Deere dealer to check the front axle pivot
pin (A) for correct end play.
PY4146
A—Front Axle Pivot Pin
PY80265,05GO934 –19–10SEP05–1/1
115-4
022607
PN=118
Service—Every 600 Hours
Adjust Engine Valve Clearance
PY4038
–UN–23FEB06
Ask your John Deere dealer to make engine valve
clearance adjustment and inspect fuel injectors
NR25796,0000238 –19–21JUN06–1/1
115-5
022607
PN=119
Service—Every 1250 Hours
Change Transmission-Hydraulic Oil and
Filter
1. Lower rockshaft to remove trapped oil.
3. Replace filter (B) while changing oil. Apply a film of oil
to new filter gasket and install new filter. Hand tighten
only.
PY4417
A—Axle Housing
B—Transmission Oil Filter
C—Transmission Case Drain Plug
–UN–31DEC04
2. Remove drain plug (C) from transmission case and
drain oil. Dispose of waste oil properly.
PY80265,05GO935 –19–12JUN06–1/2
5. Check oil level at sight glass after filling. Make sure oil
level is to full level mark (A). Check again after
operating for five minutes. Add oil if necessary.
PY4143
Specification
Transmission Oil (Rear tyre size:
12.4 X 28 or 13.6 X 28)—
Capacity .............................................................................................. 33 L
Transmission Oil (Rear tyre Size
14.9 X 28—Capacity .......................................................................... 34 L
–UN–12JUN06
4. Fill system with transmission-hydraulic oil. (See Fuels,
Lubricants and Coolant section.)
A—Full Level Mark
B—Add Level Mark
PY80265,05GO935 –19–12JUN06–2/2
120-1
022607
PN=120
Service—Every 1250 Hours
Clean Transmission-Hydraulic Pickup Screen
Remove two cap screws (A) and remove screen cover
(B).
2. Remove screen and examine it for damage. Replace if
necessary. Clean screen in solvent and blow dry with
compressed air.
PY4974
3. Carefully install screen so the front of screen is
inserted in hole at front of differential case.
–UN–22APR05
1. Drain transmission-hydraulic oil. (See Change
Transmission-Hydraulic Oil and Filter in this section.)
4. Fill system with transmission-hydraulic oil. (See
Changing Transmission-Hydraulic Oil and Filter in this
section.)
5. Check oil level at sight glass (C) after filling, and again
after operating for five minutes.
PY4973
–UN–22APR05
A—Cap Screws (2 used)
B—Screen Cover
C—Sight Glass
PY80265,05GO936 –19–10SEP05–1/1
120-2
022607
PN=121
Service—Annually
Replace Air Cleaner Elements
1. Open hood and remove side screen. (See Removing
Side Screen in Service chapter.)
2. Release clips (A).
–UN–06DEC04
3. Remove cover (B).
PY4295
4. Remove primary element (C).
5. Clean out any dirt in canister taking care not to
damage the secondary filter element.
IMPORTANT: Remove secondary element (inner
element) ONLY if it is to be replaced.
DO NOT attempt to clean secondary
element.
NOTE: When installing the air cleaner canister, make
sure that the dust unloader valve is facing down.
PY4271
6. Removal of the secondary element (D) is similar to
removal of the primary element.
–UN–06DEC04
If secondary element is replaced, install
new element immediately to prevent
dust from entering air intake system.
7. Install secondary element, primary element and cover.
8. Install side screens.
PY4294
–UN–06DEC04
A—Clips
B—Cover
C—Primary Element
D—Secondary Element
PY80265,05GO937 –19–10SEP05–1/1
125-1
022607
PN=122
Service—2 Years/2000 Hours
Flush Cooling System
–UN–28AUG04
For efficient operation, drain old coolant, flush the entire
system, and fill with clean antifreeze solution at least once
every two years.
PY4157
CAUTION: DO NOT remove radiator cap or drain
coolant until coolant is cold. Always loosen
radiator cap slowly to relieve any excess
pressure.
1. Drain coolant - Remove radiator cap (A). Open drain
plug (B) on radiator and attach a drain hose. Route
hose to container and drain coolant from radiator.
Drain coolant from engine block by removing plug (C).
–UN–28AUG04
IMPORTANT: Thermostat must be removed to ensure
a thorough flush.
PY4158
2. Remove thermostat cover (D), remove thermostat and
install cover (without thermostat). Tighten cap screws
to specification.
Specification
Thermostat Cover Cap Screws—
Torque ............................................................................. 47 N•m (35 lb-ft)
–UN–11JUN02
3. Flush system with water - Close all drain valves/plugs
and fill system with clean water. Run engine about 10
minutes to stir up possible rust or sediment. Stop
engine and drain water from system before rust and
sediment settle.
PY1234
4. Flush system with radiator cleaner - Close all drain
valve/plugs and fill the cooling system with a good
commercial radiator cleaner and water. Follow
instructions provided with cleaner. Stop engine and
immediately drain system.
5. Flush system with water - Close all drain valves/plugs
and fill with clean water to flush the system. Run the
engine about 10 minutes, then drain out flushing water.
PY4159
–UN–28AUG04
A—Radiator Cap
B—Drain Plug
C—Coolant Drain Plug
D—Thermostat Cover
Continued on next page
130-1
PY80265,05GO938 –19–05JUL06–1/2
022607
PN=123
Service—2 Years/2000 Hours
6. Remove thermostat cover and clean off the gasket
material. Apply gasket sealant to new gasket and
install thermostat and cover. Tighten cap screws to
specification.
Specification
Thermostat Cover Cap Screws—
Torque ............................................................................. 47 N•m (35 lb-ft)
7. Fill with fresh coolant - Close all drain valves/plugs and
fill with a mixture of antifreeze, soft water, and coolant
conditioner as specified in the Fuels, Lubricants, and
Coolant section.
8. Check coolant level - Fill radiator to the top of the filler
neck. Run the engine until operating temperature is
reached. Let the engine cool (preferably overnight) and
recheck the coolant level. Coolant level with a cold
engine should be at the bottom of the filler neck. When
filling the cooling system it may require several
operating/cooling periods to stabilize the coolant level
in the system. Add make-up coolant to the radiator as
needed to bring the coolant level to the correct level.
PY80265,05GO938 –19–05JUL06–2/2
130-2
022607
PN=124
Service—As Required
Under dusty conditions, it may be necessary to service air
cleaner more often than every 250 hours. Whenever dirty
primary element is indicated by loss of power, excessive
smoke or air restriction indicator light, replace primary
element (A). (See Replace Air Cleaner in Service—250
Hours section.)
PY1688
A—Primary Element
–UN–31OCT03
Service Air Cleaner
PY80265,05GO939 –19–10SEP05–1/1
Adjust Throttle Friction
1. Adjust spring tension by loosening or tightening lock
nut (A) until throttle lever movement is smooth
throughout range of travel with only slight drag.
PY4072
NOTE: Instrument and side panels removed for
illustration purposes. Throttle lever lock nut can be
accessed by lowering key switch cover.
–UN–24JAN05
When throttle linkage becomes loose and does not stay in
set position, adjust as follows:
A—Throttle Lever Lock Nut
PY80265,05GO940 –19–10SEP05–1/1
135-1
022607
PN=125
Service
Additional Service Information
This is not a detailed service manual. It contains only
information needed for operation and routine
maintenance. If you want more detailed service
information, refer to Parts Catalog and/or a Technical
Manual available at Dealership
PY80265,05GO941 –19–10SEP05–1/1
140-1
022607
PN=126
Service
PY6099
–UN–06AUG06
Service Tractor Safely
NOTE: Tractor shown may have optional equipment.
Disengage power to attachments and stop engine
before making any repairs or adjustments.
Do not change engine governor setting or overspeed
engine.
Keep the vehicle and attachments in good operating
condition.
Keep safety devices in place and in working condition.
Before you work on any part of the engine, stop the
engine, and let it cool. Hot engine parts can burn skin
on contact.
Never run engine unless range shift lever is in neutral
position.
Be careful to prevent clothing, jewelry, or long hair
from getting caught in the fan blades, drive belts, or
any other moving engine parts.
Unauthorized modifications to the machine may impair
the function and/or safety and affect machine life.
Keep all nuts, bolts, and screws tight to be sure the
equipment is in safe working condition.
NR25796,0000359 –19–07AUG06–1/1
140-2
022607
PN=127
Service
Engine Break-In Oil
New engines are filled at the factory with John Deere
ENGINE BREAK-IN OIL. During the break-in period,
add John Deere ENGINE BREAK-IN OIL as needed to
maintain the specified oil level. Change the oil and
filter after the first 100 hours of operation of a new or
rebuilt engine.
PY80265,05GO943 –19–10SEP05–1/1
Work In Ventilated Area
TS220
If you do not have an exhaust pipe extension, open the
doors and get outside air into the area
–UN–23AUG88
Engine exhaust fumes can cause sickness or death. If it is
necessary to run an engine in an enclosed area, remove
the exhaust fumes from the area with an exhaust pipe
extension.
PY80265,05GO944 –19–10SEP05–1/1
T6642EJ
IMPORTANT: Directing pressurized water at
electronic/electrical components or
connectors, bearings and hydraulic
seals, fuel injection pumps or other
sensitive parts and components may
cause product malfunctions. Reduce
pressure, and spray at a 45 to 90
degree angle.
–UN–18OCT88
Using High-Pressure Washers
PY80265,05GO945 –19–10SEP05–1/1
140-3
022607
PN=128
Service
Opening Hood
1. Push hood latch release (A) in to unlock hood.
3. Insert the hood support rod into the hood latch striker
slot (C) to hold hood in raised position.
PY5829
–UN–20JUN06
PY5152
A—Hood Latch Release
B—Hood Support Rod
C—Hood Latch Striker
–UN–21AUG05
2. Raise hood and lift the support rod (B).
PY80265,05GO946 –19–20JUN06–1/1
Removing Side Screens
1. Raise the hood and secure with the support rod.
3. Tilt screen outward and lift from lower mounting slots.
PY1736
A—Side Screens
–UN–14DEC05
2. Pull side screen (A).
PY80265,05GO947 –19–10SEP05–1/1
140-4
022607
PN=129
Service
Removing Hood
1. Remove side screens. (See Removing Side Screens in
this chapter.)
PY5813
3. Release the hood support rod from the hood latch and
secure the rod in the stored position.
–UN–19JUN06
2. Remove two cap screws (A) securing hood.
4. Remove hood from tractor.
A—Cap Screws (2 used)
PY80265,05GO948 –19–20JUN06–1/1
LV4089
Air enters the intake system through the open end of the
air cleaner canister. A major portion of the dust is
separated out by air turbulence action of the primary air
cleaner element (A) and passed out into the radiator inlet
air flow through the dust unloader valve (C). If the primary
element becomes plugged, dust is filtered out by the
secondary element (B).
–UN–20JUL99
Air Intake System Components
A—Primary Air Cleaner Element
B—Secondary Air Cleaner Element
C—Dust Unloader Valve
PY80265,05GO949 –19–10SEP05–1/1
140-5
022607
PN=130
Service
Service Air Cleaner at Regular Intervals
–UN–31MAY06
Service air cleaner if air restriction indicator (A) illuminates
or at least every 250 hours. Replace air cleaner elements
at least once a year.
PY5731
The smaller “secondary” element should be removed only
when being replaced, normally once a year. (See Replace
Air Cleaner in Service—250 Hours section.)
A—Air Restriction Indicator
For 5103, 5103S, 5203, 5104 and 5204 Tractor
PY80265,05GO950 –19–29DEC06–1/1
Service Air Cleaner at Regular Intervals
(5103E Tractor)
–UN–25AUG04
When Red indicator is seen in transparent area of Air
restriction indicator (A) or at least every 250 hours.
Replace air cleaner elements at least once a year.
A—Air Restriction Indicator
PY4093
The smaller “secondary” element should be removed only
when being replaced, normally once a year. (See Replace
Air Cleaner in Service—250 Hours section.)
For 5103E Tractor
PY80265,05GO951 –19–10SEP05–1/1
140-6
022607
PN=131
Service
PY4115
PY4016
–UN–21AUG04
–UN–14JUL04
Checking Air Intake System
For 5103, 5103S, 5203, 5104 and 5204 Tractor
For 5103E Tractor
Check all air intake system clamps (A) for tightness.
PY4116
–UN–21AUG04
A—Air Intake System Clamps
PY80265,05GO952 –19–29DEC06–1/1
140-7
022607
PN=132
Service
Removing Primary Air Cleaner Element
1. Disconnect rubber strap (A) at the front of the canister.
2. Lift clip (B) and pull canister cover.
–UN–29JUL01
3. Clean out any dirt in canister taking care not to
damage the secondary filter element.
PY1113
IMPORTANT: Remove secondary element (inner
element) ONLY if it is to be replaced.
DO NOT attempt to clean secondary
element. If secondary element is
replaced, install new element
immediately to prevent dust from
entering air intake system. When
replacing the air cleaner canister, make
sure that the dust cup/ejector hose is
facing downward.
–UN–29JUL01
PY1100
4. Removal of the secondary element is similar to
removal of the primary element.
A—Rubber Strap
B—Clip
C—Primary Element
PY80265,05GO953 –19–05JUL06–1/1
Cleaning Primary Element
IMPORTANT: DO NOT direct air against outside of
element, as it might force dirt through
to inside.
PY1114
2. clean element with compressed air (below 690 kPa or
100 psi). Hold nozzle next to inner surface, and move
up and down pleats.
–UN–29JUL01
1. Pat sides of element gently to loosen dirt. DO NOT tap
element against a hard surface.
3. Inspect element before reinstalling.
PY80265,05GO954 –19–10SEP05–1/1
140-8
022607
PN=133
Service
Washing Primary Element
2. Rinse element thoroughly from inside with clean water.
Use element cleaning gun or a free-running hose.
Keep water pressure low (below 280 kPa or 40 psi) to
avoid damaging element.
PY1122
1. If element is coated with oil or soot, wash in a solution
of warm water . Let element soak at least 15 minutes,
then agitate gently to flush out dirt.
–UN–31JUL01
IMPORTANT: Never wash element in gasoline or any
solvent. Never use compressed air on a
wet element. Do not oil element.
3. Allow element to dry completely before using. This
usually takes from one to three days. DO NOT oven
dry or use drying agents. Protect element from freezing
until dry.
4. Inspect element before installing.
PY80265,05GO955 –19–10SEP05–1/1
Inspecting Element
3. Be sure rubber sealing surfaces (C) are in good
condition on both ends. If damaged, replace element.
PY1636
2. Be sure outer screen is not dented. Vibration would
quickly wear a hole in filter.
–UN–30SEP03
1. Hold a bright light (A) inside element (B) and check
carefully for holes. Discard any element which shows
the slightest hole.
A—Light Source
B—Element
C—Rubber Sealing Surface
PY80265,05GO956 –19–10SEP05–1/1
140-9
022607
PN=134
Service
Storing Element
RW471
–UN–26FEB90
If element is not installed on tractor, seal element in a
plastic bag and store in its original shipping container to
protect against dust and damage.
PY80265,05GO957 –19–10SEP05–1/1
Replacing Alternator/Fan Belt
1. Loosen cap screw (A) and bolt (B) and rotate the
alternator (C) to free the belt.
–UN–27OCT03
2. Remove belt from drive pulley.
3. Belt can be pulled around fan to remove.
PY1652
4. Install new belt in reverse order of removal.
5. Adjust belt tension. (See Inspect and Adjust
Alternator/Fan Belt in Service—250 Hours section.)
A—Alternator Cap Screw
B—Alternator Bolt
C—Alternator
PY80265,05GO958 –19–10SEP05–1/1
140-10
022607
PN=135
Service
PY4895
PY4887
–UN–11APR05
–UN–19APR05
Fuel System Components
A—Mico Fuel filter Assembly
B—Primary Filter
C—Secondary filter
D—Bleeding Screws-2 nos
E—Sediment Drain Screws-2
nos
F—Fuel Injection Lines
G—Fuel Line to Pump
H—Fuel return line
I—Hand Priming Pump
J— Lubrication
K—Acclerator
L—Fuel Shut Off Lever
PY80265,05GO959 –19–10SEP05–1/1
Do Not Modify Fuel System
IMPORTANT: Modification or alteration of the
injection pump, the injection pump
timing, or the fuel injectors in ways
not recommended by the
manufacturer will terminate the
warranty obligation to the purchaser.
(See warranty information inside
front cover.)
DO NOT attempt to service injection
pump or fuel injectors yourself.
Special training and special tools are
required. (See your John Deere
dealer.)
PY80265,05GO960 –19–10SEP05–1/1
140-11
022607
PN=136
Service
Bleeding Fuel System
1. Loosen fuel return line (A).
–UN–21AUG04
2. Unscrew hand primer (B) on fuel supply pump until it
can be pulled by hand.
4. Simultaneously stroke the hand primer down and close
the fuel return port. This prevents air from entering the
system. Tighten securely.
PY4117
3. Operate the hand primer until fuel flow is free from air
bubbles.
A—Fuel Return Line
B—Hand Primer
5. Lock hand primer in position.
PY80265,05GO961 –19–10SEP05–1/1
Bleed Fuel System At Fuel Injection Nozzles
If engine will not start after the bleeding procedures
described above, continue as follows:
3. Turn over engine with starter motor until fuel flows free
from bubbles out of loosened fuel nozzle connections.
Retighten connections.
PY1743
2. Using two open-end wrenches, loosen fuel line on at
least three nozzles.
–UN–06NOV03
1. Place throttle lever in fast idle position.
PY80265,05GO962 –19–10SEP05–1/1
140-12
022607
PN=137
Service
–UN–28AUG04
PY4163
PY4161
–UN–28AUG04
Engine Cooling System
PY4162
IMPORTANT: Never pour cold water into the cooling
system of a hot engine, as it might
crack cylinder block or head. DO NOT
operate engine without coolant for even
a few minutes.
–UN–28AUG04
Coolant is added in coolant recovery tank and not in
radiator directly. For efficient operation, drain old coolant,
flush entire cooling system atleast once in two years (See
procedure in Service-2 years / 2000 hours section)
A—Radiator Cap
B—Radiator
C—Coolant Recovery Tank
D—Upper Radiator Hose
E—Thermostat Valve
F—Radiator Drain Plug
PY80265,05GO963 –19–10SEP05–1/1
140-13
022607
PN=138
Service
Cleaning Grille, Screens, Radiator and Oil
Cooler
TS266
CAUTION: Reduce compressed air to less than
210 kPa (2 bar) (30 psi) when using for cleaning
purposes. Clear area of bystanders, guard
against flying chips, and wear personal
protection equipment including eye protection.
–UN–23AUG88
1. Whenever trash builds up on front grille (A) or side
screens (B), stop engine and brush clean.
2. Remove side screens (B), and see if trash has built up
on radiator (C). If so, carefully remove it using a brush
or compressed air.
3. If a more thorough cleaning is necessary, clean
radiator from behind with compressed air or water.
Straighten any bent fins.
PY1804
–UN–15NOV03
A—Grille
B—Side Screens
C—Radiator
PY80265,05GO964 –19–10SEP05–1/1
Prevent Battery Explosions
Never check battery charge by placing a metal object
across the posts. Use a volt-meter or hydrometer.
TS204
Do not charge a frozen battery; it may explode. Warm
battery to 16°C (60°F).
–UN–23AUG88
Keep sparks, lighted matches, and open flame away from
the top of battery. Battery gas can explode.
PY80265,05GO965 –19–10SEP05–1/1
140-14
022607
PN=139
Service
To avoid shocks and burns, disconnect battery
negative (ground) cable (B) before servicing any
part of the electrical system, then remove
positive cable (A) if removing battery.
TS204
CAUTION: Keep all sparks and flames away
from batteries, as gas given off by electrolyte is
explosive. To avoid sparks, connect negative
(ground) cable (B) last and disconnect it first.
When using a booster battery, follow
instructions in “Operating the Engine” section.
–UN–23AUG88
Observe Electrical Service Precautions
Keep all electrical shields in place.
PY4102
–UN–10DEC05
A—Positive (+) Battery Cable
B—Negative (—) Battery Cable
PY80265,05GO966 –19–10SEP05–1/1
Battery Access
Battery is located in front of the radiator.
–UN–14DEC05
To gain access:
1. Raise the hood.
PY1736
2. Pull side screens (A) and remove from slots. (See
Removing Side Screens in this section.)
A—Side Screens
PY80265,05GO967 –19–10SEP05–1/1
140-15
022607
PN=140
Service
Removing Battery
CAUTION: To avoid sparks, disconnect negative
(ground) cable first and connect it last.
–UN–10DEC05
1. Remove negative (ground) battery cable (B) and
remove the cable connection. Then remove positive
cable (A) and connection.
2. Lift and slide the battery from the battery tray.
PY4102
Loosen nuts securing battery hold-down and rotate the
holder down, freeing the battery.
A—Positive (+) Cable Nut
B—Negative (—) Cable Nut
PY80265,05GO968 –19–10SEP05–1/1
140-16
022607
PN=141
Service
Checking Battery Condition
Always remove grounded (—) battery clamp
first and replace it last.
TS204
Never check battery charge by placing a metal
object across the posts. Use a voltmeter or
hydrometer.
–UN–23AUG88
CAUTION: Battery gas can explode. Keep
sparks and flames away from batteries. Use a
flashlight to check battery electrolyte level.
1. Use a battery hydrometer to check specific gravity of
electrolyte in each cell. Charge battery if reading is
below 1.215. Replace battery if difference between
cells is more than 0.050 or if battery will not charge
above 1.225.
2. Always correct specific gravity reading for electrolyte
temperature variation. Add 0.004 to the reading
obtained in step one for every 10°F above 80°F (add
0.007 to the reading for every 10° above 27°C).
Subtract at same rate if electrolyte temperature is
below 80°F (27°C). Corrected specific gravity of a fully
charged battery is from 1.265 to 1.280.
3. A battery is considered fully charged when three
consecutive hydrometer readings, taken at hourly
intervals, show no rise in specific gravity.
PY80265,05GO969 –19–10SEP05–1/1
140-17
022607
PN=142
Service
Servicing Battery
–UN–10DEC05
1. Keep battery clean by wiping with a damp cloth. Keep
all connections (A and B) clean and tight. To remove
any corrosion, wash terminals with a solution of four
parts water to one part baking soda.
PY4102
CAUTION: To avoid sparks, connect negative
(ground) (—) cable last and disconnect it first.
2. Keep battery fully charged, especially during cold
weather. If a battery charger is connected, attach a
positive cable to the positive battery terminal (A).
Connect the negative battery charger lead to a good
ground on tractor frame.
A—Positive (+) Battery Terminal
B—Negative (—) Battery Terminal
Continued on next page
140-18
PY80265,05GO970 –19–10SEP05–1/2
022607
PN=143
Service
CAUTION: Sulfuric acid in battery electrolyte is
poisonous. It is strong enough to burn skin, eat
holes in clothing, and cause blindness if
splashed into eyes.
Avoid the hazard by:
1. Filling batteries in a well-ventilated area.
2. Wearing eye protection and rubber gloves.
3. Avoiding breathing fumes when electrolyte is
added.
4. Avoiding spilling or dripping electrolyte.
5. Use proper jump start procedure.
If you spill acid on yourself:
–UN–23AUG88
1. Flush your skin with water.
2. Apply baking soda or lime to help neutralize
the acid.
3. Flush your eyes with water for 15—30
minutes. Get medical attention immediately.
TS203
If acid is swallowed:
1. Do not induce vomiting.
2. Drink large amounts of water or milk, but do
not exceed 2 L (2 quarts).
3. Get medical attention immediately.
IMPORTANT: DO NOT add water in freezing weather
unless tractor will be run at least 30
minutes to assure thorough mixing.
–UN–28AUG04
3. Check level of electrolyte in each cell (A) at least every
250 hours. If low, fill to bottom of filler necks with
CLEAN, SOFT water. DO NOT OVERFILL.
PY4164
4. Coat terminals with a small amount of grease.
A—Battery Cells
PY80265,05GO970 –19–10SEP05–2/2
140-19
022607
PN=144
Service
Charging Battery
1. With charger off, attach positive battery charger lead to
positive (+) battery terminal (A). Attach negative
charger lead to tractor frame away from the battery.
TS204
CAUTION: Gas given off by battery is explosive.
Keep sparks and flames away from battery.
Before connecting or disconnecting a battery
charger, turn charger off. Make last connection
and disconnection at a point away from battery.
–UN–23AUG88
Keep battery fully charged, especially during cold weather.
PY4102
3. To disconnect battery charger, turn charger off.
Remove negative charger lead first, follow by positive
charger lead.
–UN–10DEC05
2. Turn charger on and recharge the battery following
battery manufacturer’s instructions for using charger.
Check battery condition as described below.
A—Positive (+) Battery Terminal
B—Negative (—) Battery Terminal
PY80265,05GO971 –19–10SEP05–1/1
Battery Replacement Specifications
When replacing battery, use recommended battery. See
your John Deere dealer.
Specification
Battery—Volts ................................................................................ 12 Volts
Ampere Rating.................................................................................. 88 AH
Make ................................................................................................. Exide
Model ................................................................................................... E88
PY80265,05GO972 –19–10SEP05–1/1
140-20
022607
PN=145
Service
Connecting Starter Wiring
–UN–12APR05
IMPORTANT: Disconnect battery negative (ground)
cable before servicing any part of
electrical system. Make all other
connections before connecting ground
cable.
PY4876
Connect large battery cable (A) and alternator cable to
large solenoid post (B). Connect the small white wire (C)
to solenoid terminal (D).
A—Large Battery Cable
B—Large Solenoid Post
C—Small White Wire
D—Solenoid Terminal
PY80265,05GO973 –19–07JUL06–1/1
Connecting Alternator Wiring For (5103E)
If alternator is disconnected for any reason, connect wires
(A), (B) and (C) as shown at right.
PY4165
To prevent damage to electrical system,
disconnect alternator before making
any electrical weld repairs. If an
attached implement needs weld repair,
disconnect it from tractor before
welding, to prevent damage to tractor
electrical system.
–UN–28AUG04
IMPORTANT: Disconnect battery negative (ground)
cable before servicing any part of
electrical system. Make all other
connections before connecting ground
cable.
A—Alternator Wire
B—Alternator-Battery Charging Indicator Wire
C—Hourmeter Wire
PY80265,05GO974 –19–10SEP05–1/1
140-21
022607
PN=146
Service
Connecting Alternator Wiring For (5103,
5103S, 5203)
PY1658
To prevent damage to electrical system,
disconnect alternator before making
any electrical weld repairs. If an
attached implement needs weld repair,
disconnect it from tractor before
welding, to prevent damage to tractor
electrical system.
–UN–15DEC05
IMPORTANT: Disconnect battery negative (ground)
cable before servicing any part of
electrical system. Make all other
connections before connecting ground
cable.
A—Alternator Wire
B—Alternator-Battery Charging Indicator Wire
If alternator is disconnected for any reason, connect wires
(A) and (B) as shown at right.
PY80265,05GO975 –19–10SEP05–1/1
Locating Fusible Link
Electrical circuits are protected by fusible link(s).
–UN–07AUG06
Fusible link (A) is located under hood on right-hand side
of tractor, above fuel filter.
PY6112
A—Fusible Link
NR25796,000035A –19–07AUG06–1/1
140-22
022607
PN=147
Service
Locating Fuses
All electrical circuits are protected by fuses. Amperage
rating is marked on each fuse, plus fuses are color coded
to ensure proper replacement.
To access fuse panel (A), remove four cap screws to
lower fuse panel cover.
20 Amp
Yellow
30 Amp
Green
–UN–23AUG05
Color
Red
IMPORTANT: DO NOT replace original fuse with
higher rated fuse or machine damage
may occur. If original size fuse will not
carry electrical load and continues to
blow, have the electrical system
checked by your John Deere dealer.
PY5163
Fuse Rating
10 Amp
For 5103, 5103S, 5203, 5104 and 5204 Tractor
PY5164
–UN–23AUG05
A—Fuse Panel
For 5103E Tractor
PY80265,05GO977 –19–29DEC06–1/1
140-23
022607
PN=148
Service
PY1674
–UN–30OCT03
Fuse Size and Function
For 5103, 5103S, 5203, 5104 and 5204 Tractor
A—20 amp—Park Light
B—20 amp—High Beam Light
C—20 amp—Low Beam Light
H—10 amp—Alternator
I—10 amp—Brake Light
J—20 amp—Flood Light
K—10 amp—Radio
L—20 amp—Flasher
M—30 amp—Key switch
N—30 amp—Accessory Relay
PY80265,05GO978 –19–29DEC06–1/1
140-24
022607
PN=149
Service
PY4118
–UN–27AUG04
Fuse Size and Function (5103E Tractor)
For 5103E Tractor
A—10 amp—Park Light
B—20 amp—Accessory Relay
C—20 amp—Flasher
D—10 amp—Flood Light
E—20 amp—Brake Light
F—10 amp—Alternator
K—10 amp—High Beam Light
L—10 amp—Low Beam Light
M—Relay R1
PY80265,05GO979 –19–10SEP05–1/1
140-25
022607
PN=150
Service
Aiming Headlights
1. Park tractor on level ground, with lights 8 m (25 ft)
from a wall.
2. Measure from top of hood to the ground (A). Place a
strip of masking tape (B) on the wall at the same
height.
3. Place a piece of tape, folded in the middle to make a
point, on the top front center of the hood.
6. Turn light switch to dim position.
7. Locate small zone of bright light projected by each
lamp. Cover other lamps if necessary. Top of zone (E)
should be 130 mm (5 in.) below the tape. Left edge of
zone (F) should be 130 mm (5 in.) left of lamp location
marked (D).
PY5290
5. From tractor centerline (C), mark a point 130 mm (5
in.) out in each direction (D). This mark locates a point
directly in front of center of each headlight.
–UN–12DEC05
4. Using the hood tape as a guide, sight across steering
wheel and hood to locate tractor centerline. Mark
tractor centerline (C) on wall.
8. To adjust headlights, see Adjusting Headlights in this
section.
LV3020
–UN–10JUN99
A—Hood-to-Ground Distance
B—Masking Tape
C—Tractor Centerline
D—Center of Headlight
E—Top of Zone
F—Left Edge of Zone
PY80265,05GO980 –19–10SEP05–1/1
140-26
022607
PN=151
Service
Adjusting Headlights
1. Open the hood.
–UN–12DEC05
2. Turn screws (A—C) counterclockwise to lower beam or
clockwise to raise beam.
4. To adjust beam out from center of tractor, turn screws
(B and C) counterclockwise and screw (A) clockwise
an equal number of turns on each screw.
NOTE: Clips (D) need not be removed for adjustment.
PY4104
3. To adjust beam in toward center of tractor, turn screw
(A) counterclockwise and screws (B and C) clockwise
an equal number of turns on each screw.
A—Headlight Mounting Screw
B—Headlight Mounting Screw
C—Headlight Mounting Screw
D—Clips
PY80265,05GO981 –19–10SEP05–1/1
140-27
022607
PN=152
Service
Replace Headlight Bulb
1. Remove headlight connector (A).
CAUTION: A halogen bulb is pressurized and
may shatter. Protect bulb against abrasions and
scratches.
PY4920
3. Remove bulb (D).
–UN–12DEC05
2. Remove dust boot (B).
To guard against personal injury, wear
protective eyeglasses and clothing when
handling bulb. Turn power off when installing
and before removing bulb. Dispose of bulb with
care.
Read and follow all bulb manufacturers
installation instructions.
4. Install bulb, collar, seal and connector in reverse order.
PY4921
–UN–12DEC05
Allow bulb to cool before removing.
PY4922
–UN–12DEC05
A—Headlight Connector
B—Dust Boot
C—Collar
D—Bulb
PY80265,05GO982 –19–10SEP05–1/1
140-28
022607
PN=153
Service
Replace Tail Light and Warning Light Bulbs
1. Remove screws (A).
2. Remove lens.
3. Push and twist to release bulb from socket.
–UN–12JUN06
4. Reverse this procedure to reassemble light.
PY5018
A— Cap Screws (4 used)
PY5020
–UN–12JUN06
For 5103, 5103S, 5203, 5104 and 5204 Tractor
For 5103E Tractor
PY80265,05GO983 –19–29DEC06–1/1
Replace Flood Lamp Bulb
3. Disconnect wiring leads from bulb.
4. Rotate bulb counterclockwise and remove.
5. Reverse the procedure to reassemble the flood lamp.
PY4167
2. Remove screw, lamp cover and lamp from housing.
–UN–28AUG04
1. Loosen mounting hardware (A) and rotate flood lamp
up to access cover fastening screw.
PY80265,05GO984 –19–29DEC06–1/1
140-29
022607
PN=154
Service
Checking Tyres
1. Check tyres daily for damage or noticeably low
pressure.
tractor has no added weight. If you
install ballast or mounted
implements, or if you pull heavy
loads, increase pressure.
2. Have any cuts or breaks repaired as soon as
possible.
3. Protect tyres from exposure to sunlight, petroleum
products and chemicals.
4. Drive carefully. Try to avoid rocks and sharp
objects.
5. At least every 100 hours of operation, check tyres
with an accurate gauge having 10 kPa (0.1 bar) (1
psi) graduations. If tyres contain liquid ballast, use a
special air-water gauge and measure with valve
stem at bottom.
Refer to Tyre Inflation Pressure Chart in Wheels,
Tyres and Treads section.
IMPORTANT: Minimum pressures may be used
only for light loads and only if
PY80265,05GO985 –19–10SEP05–1/1
140-30
022607
PN=155
Troubleshooting
Engine Troubleshooting
Symptom
Problem
Solution
Engine hard to start or will not
start
Improper starting procedure.
Reviewing starting procedure.
No fuel.
Check fuel tank.
Air in fuel tank.
Bleed fuel tank.
Hand primer left raised.
Push primer down.
Slow starter speed.
See “Starter Cranks Slowly”.
Crankcase oil too heavy.
Use oil of proper viscosity.
Improper type of fuel.
Consult fuel supplier; use proper
type fuel for operating conditions.
Water, dirt, or air in fuel system.
Drain, flush, fill and bleed system.
Clogged fuel filter.
Replace filter element.
Dirty or faulty injectors.
Have John Deere dealer check
injectors.
Fuel shut-off valve closed.
Open fuel shut-off valve.
Insufficient oil.
Add oil.
Injection pump out of time.
See your John Deere dealer.
Low coolant temperature.
See your John Deere dealer.
Engine overheating.
See “Engine Overheats”.
Low coolant temperature.
See your John Deere dealer.
Clogged fuel filter.
Replace filter element.
Water, dirt, or air in fuel system.
Drain, flush, fill, and bleed system.
Dirty or faulty injectors.
Have John Deere dealer check
injectors.
Improper type of fuel.
Use proper fuel.
Engine knocks
Engine runs irregularly or stalls
frequently
Continued on next page
145-1
PY80265,05GO986 –19–10SEP05–1/4
022607
PN=156
Troubleshooting
Symptom
Problem
Solution
Below normal engine
temperature
Defective temperature gauge or
sender.
Check gauge, sender, and
conditions.
Lack of power
Engine overloaded.
Reduce load or shift to lower gear.
Low fast idle speed.
See your John Deere dealer.
Intake air restriction.
Service air cleaner.
Clogged fuel filter.
Replace filter element.
Improper type of fuel.
Use proper fuel.
Overheated engine.
See “Engine Overheats”.
Below normal engine temperature.
See your John Deere dealer.
Improper valve clearance.
See your John Deere dealer.
Dirty or faulty injectors.
Have John Deere dealer check
injectors.
Injection pump out of time.
See your John Deere dealer.
Implement improperly adjusted.
See implement operator’s manual.
Restricted fuel line.
See your John Deere dealer.
Restricted return line.
See your John Deere dealer.
Improper ballast.
Adjust ballast to load.
Low oil level.
Add oil.
Improper type of oil.
Drain, fill crankcase with oil of proper
viscosity and quality.
Crankcase oil too light.
Use proper viscosity oil.
Oil leaks.
Check for leaks in lines, around
gaskets and drain plugs.
Restricted crankcase vent tube.
Clean vent tube.
Low oil pressure
High oil consumption
Continued on next page
145-2
PY80265,05GO986 –19–10SEP05–2/4
022607
PN=157
Troubleshooting
Symptom
Problem
Solution
Engine emits white smoke
Improper type fuel.
Use proper fuel.
Low engine temperature.
Warm up engine to normal operating
temperature.
Defective thermostat.
See your John Deere dealer.
Defective injection nozzles.
See your John Deere dealer.
Engine out of time.
See your John Deere dealer.
Cold start advance or light load
advance not functioning.
See your John Deere dealer.
Improper type of fuel.
Use proper fuel.
Clogged or dirty air cleaner.
Service air cleaner.
Engine overloaded.
Reduce load or shift to a low gear.
Injection nozzles dirty.
See your John Deere dealer.
Engine out of time.
See your John Deere dealer.
Dirty radiator core, or grille screens.
Remove all trash.
Engine overloaded.
Shift to lower gear or reduce load.
Low engine oil level.
Check oil level. Add oil as required.
Low coolant level.
Fill radiator to proper level, check
radiator, and hoses for loose
connection or leaks.
Faulty radiator cap.
Replace cap.
Loose or defective fan belt(s).
Adjust belt tension(s).
Cooling system needs flushing.
Flush cooling system.
Defective thermostat.
See your John Deere dealer.
Defective temperature gauge or
sender.
See your John Deere dealer.
Incorrect grade of fuel.
Use proper fuel.
Engine emits black or gray
exhaust smoke
Engine overheats
Continued on next page
145-3
PY80265,05GO986 –19–10SEP05–3/4
022607
PN=158
Troubleshooting
Symptom
Problem
Solution
High fuel consumption.
Improper type of fuel.
Use proper fuel.
Clogged or dirty air cleaner.
Service air cleaner.
Engine overloaded.
Reduce load or shift to a lower gear.
Improper valve clearance.
See your John Deere dealer.
Injection nozzles dirty.
See your John Deere dealer.
Engine out of time.
See your John Deere dealer.
Implement improperly adjusted.
See implement operator’s manual.
Low engine temperature.
See your John Deere dealer.
Excessive ballast.
Adjust ballast to load.
Restricted air intake system.
Check system.
Plugged crankcase vent tube.
Clean vent tube.
PY80265,05GO986 –19–10SEP05–4/4
Transmission Troubleshooting
Symptom
Problem
Solution
Transmission oil overheats
Low oil supply.
Fill system with correct oil.
Clogged transmission-hydraulic oil
filter.
Replace filter.
Internal hydraulic leak.
See your John Deere dealer.
Hitch feedback linkage improperly
adjusted.
Reset linkage. See your John Deere
dealer.
Hydraulic motor not plumbed
correctly.
See your John Deere dealer.
Low oil supply.
Fill system with correct oil.
Clogged transmission-hydraulic oil
filter.
Replace filter.
Low transmission pressure.
PY80265,05GO987 –19–10SEP05–1/1
145-4
022607
PN=159
Troubleshooting
Hydraulic System Troubleshooting
Symptom
Problem
Solution
Entire hydraulic system fails to
function
Low oil supply.
Fill system with correct oil.
Clogged transmission-hydraulic filter.
Replace filter.
Clogged transmission-hydraulic
pickup screen.
Clean pickup screen.
High-pressure internal leak.
See your John Deere dealer.
Low oil supply.
Fill system with correct oil.
Clogged transmission-hydraulic oil
filter.
Replace filter.
Internal hydraulic leak.
See your John Deere dealer.
Hitch feedback linkage improperly
adjusted.
Reset linkage. See your John Deere
dealer.
Hydraulic motor not plumbed
correctly.
See your John Deere dealer.
Hydraulic oil overheats
PY80265,05GO988 –19–10SEP05–1/1
Brakes Troubleshooting
Symptom
Problem
Solution
No solid pedal feel
Pedals adjusted incorrectly.
See your John Deere dealer.
Excessive pedal travel
Pedals adjusted incorrectly.
See your John Deere dealer.
Brakes drag during transport
Brakes out of adjustment.
See your John Deere dealer.
PY80265,05GO989 –19–10SEP05–1/1
145-5
022607
PN=160
Troubleshooting
Rockshaft and 3-Point Hitch Troubleshooting
Symptom
Problem
Solution
Insufficient transport clearance
Center link too long.
Adjust center link.
Lift links to long.
Adjust lift links.
Implement not level.
Level implement.
Implement not properly adjusted.
See implement operator’s manual.
Front of center link in upper holes.
Move center link to lower holes.
Sway chains adjusted to short.
Lengthen sway chains.
Hitch drops slowly
Rockshaft rate-of-drop control not
properly set.
Adjust rate-of-drop knob.
Hitch fails to lift or lifts slowly
Excessive load on hitch.
Reduce load.
Low oil level.
Fill system with proper oil.
Hydraulic oil too cold.
Allow oil to warm.
Transmission-hydraulic oil filter
clogged.
Replace filter.
Transmission-hydraulic pickup
screen clogged.
Clean or replace pickup screen.
Lift links too short.
Adjust lift links.
Lack of penetration.
See implement operator’s manual.
Improper setting of limit stop.
Reset position limit.
Improper setting of draft lever.
See Rockshaft and 3-Point Hitch
section.
Implement will not operate at
desired depth
Continued on next page
145-6
PY80265,05GO990 –19–10SEP05–1/2
022607
PN=161
Troubleshooting
Symptom
Problem
Solution
Insufficient or no hitch response
to draft load
Front attachment of center link in
upper holes.
Move center link attachment to lower
bracket holes.
Draft control lever in “Off” position.
Move lever rearward.
Lift links too short.
Adjust lift links.
Lack of penetration.
See implement operator’s manual.
Rate-of-drop too slow.
Adjust rate-of-drop valve.
Front attachment on center link in
lower bracket holes.
Move center link attachment to
upper bracket holes.
Improper draft sensing adjustment.
Move lever forward.
Hitch drops too fast
Rate-of-drop set too fast.
Adjust rate-of-drop.
Rockshaft control levers “drift”.
Levers too loose.
Friction disks are loose.
Adjust rockshaft control lever friction.
See procedures in “Rockshaft and
3-Point Hitch” section or see your
John Deere dealer.
Hitch too responsive
PY80265,05GO990 –19–10SEP05–2/2
145-7
022607
PN=162
Troubleshooting
Electrical System Troubleshooting
Symptom
Problem
Solution
Battery will not charge
Loose or corroded connections.
Clean and tighten connections.
Sulfated or worn-out battery.
Check electrolyte level and specific
gravity.
Loose or defective alternator/fan
belt.
Adjust belt tension or replace belt.
Low engine speed.
Increase speed.
Defective battery.
Check electrolyte level and specific
gravity.
Defective alternator.
See your John Deere dealer.
Slipping alternator/fan belt.
Adjust belt tension.
Range shift lever in gear.
Move lever to neutral.
PTO lever in engaged position.
Move PTO lever to disengaged
position.
Low battery output.
See your John Deere dealer.
Blown fuse.
Replace fuse.
Low battery output.
Check electrolyte level and specific
gravity.
Crankcase oil too heavy.
Use proper viscosity oil.
Loose or corroded connections.
Clean and tighten loose connections.
Blown fuse.
Replace fuse.
Charging system indicator glows
with engine running
Starter inoperative
Starter cranks slowly
Light system does not function;
rest of electrical system
functions
Continued on next page
145-8
PY80265,05GO991 –19–10SEP05–1/2
022607
PN=163
Troubleshooting
Symptom
Problem
Solution
Entire electrical system does not
function
Faulty battery connections.
Clean and tighten connections.
Sulfated or worn-out battery.
Check electrolyte level and specific
gravity.
Blown fuse.
Replace fuse.
Diode to protect circuit from arcing
has failed.
See your John Deere dealer.
Relay(s) sticking or
nonfunctional; repeated failures
PY80265,05GO991 –19–10SEP05–2/2
145-9
022607
PN=164
Tractor Storage
Storing Tractor
–UN–12DEC05
IMPORTANT: Any time tractor will not be used for
several months, use this procedure to
minimize corrosion and deterioration.
1. Service air cleaner (A). (See Servicing Air Cleaner in
Service section.)
PY4442
2. If coolant has been in tractor for two years, flush
cooling system (B). (See Flushing Cooling System in
Service section.) Add 50 percent antifreeze water
mixture. Test coolant for adequate cold weather
protection.
3. Change engine oil and filter (D). (See Change Engine
Oil and Filter in Service—250 Hours section.)
–UN–12DEC05
4. Drain fuel and add back 4 L of fuel. Then add 0.4 L of
corrosion inhibitor.
PY4168
5. Add 0.25 L of corrosion inhibitor to
transmission-hydraulic system fill port (E).
6. Depress clutch and start engine. Run engine until it
reaches operating temperature. Also raise and lower
rockshaft several times. Shut off engine.
PY4170
–UN–12DEC05
PY4169
–UN–12DEC05
A—Air Cleaner
B—Cooling System
C—Engine Oil Drain Plug
D—Engine Oil Filter
E—Transmission-Hydraulic Oil Filler Cap
.
Continued on next page
150-1
PY80265,05GO992 –19–29DEC06–1/3
022607
PN=165
Tractor Storage
7. Add 0.5 L more inhibitor to fuel tank at either filler cap
(A).
8. Add 0.5 L inhibitor to engine crankcase at filler (B).
–UN–27MAY05
9. Remove air intake hose at manifold. Pour 0.1 L
inhibitor into manifold and replace hose. Pull hand
throttle back to slow idle position. Crank engine only a
few revolutions.
10. Loosen alternator/fan belt after they have cooled.
PY5027
11. Remove and clean battery. Store in a cool, dry place.
Keep it charged.1
For 5103, 5103S, 5203, 5104 and 5204 Tractor
12. Tie or block clutch pedal in the disengaged position.
13. Coat exposed metal surfaces, such as adjustable
front axles, if extended, with grease or a corrosion
inhibitor.
PY4101
–UN–20AUG04
A—Fuel Tank Filler Cap
B—Engine Oil Filler Cap
PY4036
–UN–19JUN06
For 5103E Tractor
1
Disconnect battery ground cable for short-term storage periods (20 to
90 days).
Continued on next page
150-2
PY80265,05GO992 –19–29DEC06–2/3
022607
PN=166
PY5004
PY4036
–UN–21MAY05
–UN–19JUN06
Tractor Storage
–UN–12DEC05
14. Use tape to seal air inlet hole (A), dust unloader valve
(E), exhaust pipe, crankcase filler (B), fuel caps, and
transmission-hydraulic system filler cap (C).
PY4142
15. Cover dash with opaque material to prevent gauges
from fading.
16. Raise tyres off ground. Protect them from heat and
sunlight.
A—Air Cleaner Inlet Hole
B—Engine Oil Filler Cap
C—Transmission-Hydraulic Oil Filler Cap
E—Dust Unloader Valve
17. Thoroughly clean tractor. Touch up any painted
surfaces that are scratched or chipped.
18. If tractor must be stored outside, cover it with a
waterproof material.
PY80265,05GO992 –19–29DEC06–3/3
150-3
022607
PN=167
Tractor Storage
Removing Tractor From Storage
1. Check tyre inflation pressure. (See Wheels, Tyres
and Treads section.) Lower tyres to ground.
6. Drain a small amount of fuel from fuel tank to purge
any moisture condensation that has collected.
2. Unseal all openings sealed in “Storing Tractor”.
7. Fill fuel tank.
3. Install battery.
8. Perform all appropriate 10-hour, 50-hour, 250-hour,
and 600-hour services as instructed in Lubrication
and Maintenance section.
4. Remove ties or block which secured clutch pedal
down.
9. Check all instruments and indicators by turning key
switch to ON position.
5. Check levels of engine oil, transmission-hydraulic
oil, and engine coolant, Add if necessary.
PY80265,05GO993 –19–10SEP05–1/2
IMPORTANT: DO NOT operate starter more than 20
seconds at a time, and wait at least two
minutes for starter to cool before trying
again.
–UN–16FEB06
10. Pull hand throttle (A) all the way down, depress clutch
pedal, and crank engine until oil pressure rises.
12. Depress clutch pedal and start engine. Operate
engine at slow idle for several minutes. Warm up
carefully and check all systems before placing tractor
under load.
PY4485
11. Connect wiring lead to fuel injection pump shut-off
solenoid.
A—Hand Throttle
PY80265,05GO993 –19–10SEP05–2/2
150-4
022607
PN=168
Specifications
John Deere 5103E Tractor
5103E—3029D Naturally Aspirated Engine
Observed PTO power
Brakes
24.4 kW (33.2 PS)
Type
Wet disc brakes
Max. engine torque
128 N.m
Actuation
Mechanical
Cylinders
3
Bore
106.5 mm
Hydraulics
Stroke
110 mm
Pump output
Displacement
2.9 L
Lifting capacity
Compression ratio
17.8:1
Firing order
1-2-3
Slow idle
850±25
Fast idle
2485±25
Operating range
1400-2300
Injection pump timing
15.5 ± 1° BTDC
12 V, 88 Ah
Alternator
43Amp
Starter
12 V, 2.5 kW
Single
Gearbox type
Collar Shift
No. of forward gears
8
No. of reverse gears
4
PTO speed
540 rpm
Front tyre
6.0 x 16, 8 PR
Rear tyre
12.4 x 28, 12 PR
Dimensions and Weight
Transmission
Clutch type
1100 kgf
Wheels and Tyres
Electrical
Battery
25.7 l/min
Total weight
1790 kg
Wheel base
1950 mm
Overall lenght
4080 mm
Overall width
1650 mm
Overall height (with exhaust pipe)
2205 mm
Ground clearance
365 mm
Turning radius w. brake
2840 mm
Turning radius w/o brake
3210 mm
Filling capacities
Fuel tank
50 lit
Engine sump
8.5 lit
Transmission
33 lit
Hydraulics
Common to transmission
PY80265,05GO994 –19–10SEP05–1/1
155-1
022607
PN=169
Specifications
John Deere 5103 Tractor
5103—3029D Naturally Aspirated Engine
Observed PTO power
Brakes
24.4 kW (33.2 PS)
Type
Wet disc brakes
Max. engine torque
139 N.m
Actuation
Mechanical
Cylinders
3
Bore
106.5 mm
Hydraulics
Stroke
110 mm
Pump output
Displacement
2.9 L
Lifting capacity
Compression ratio
17.8:1
Firing order
1-2-3
Slow idle
850±25
Fast idle
2485±25
Operating ragne
1400-2300
Injection pump timing
15.5 ±1° BTDC
12 V, 88 Ah
Alternator
43 Amp
Starter
12 V, 2.5 kW
Single
Gearbox type
Collar Shift
No. of forward gears
8
No. of reverse gears
4
PTO speed
540 rpm
Front tyre
6.0 x 16, 8 PR
Rear tyre
12.4 x 28, 12 PR
Dimensions and Weight
Transmission
Clutch type
1220 kgf
Wheels and Tyres
Electrical
Battery
25.7 l/min
Total weight
1800 kg
Wheel base
1950 mm
Overall lenght
3335 mm
Overall width
1650 mm
Overall height (with exhaust pipe)
2205 mm
Ground clearance
365 mm
Turning radius w. brake
2840 mm
Turning radius w/o brake
3210 mm
Filling capacities
Fuel tank
62 lit
Engine sump
8.5 lit
Transmission
33 lit
Hydraulics
Common to transmission
PY80265,05GO995 –19–10SEP05–1/1
155-2
022607
PN=170
Specifications
John Deere 5103S Tractor
5103S—3029D Naturally Aspirated Engine
Observed PTO power
Hydraulics
26.5 kW (36.05 PS)
Pump output
25.7 l/min
Max. engine torque
139 N.m
Lifting capacity
1220 Kgf
Cylinders
3
Bore
106.5 mm
Wheels and Tyres
Stroke
110 mm
Front tyre
Displacement
2.9 L
Rear tyre
Compression ratio
17.8:1
6.0 x 16, 8 PR
12.4 x 28, 12PR
13.6 x 28, 12PR (Optional)
Firing order
1-2-3
Slow idle
850±25
Total weight
1810 kg
Fast idle
2485±25
Wheel base
1950 mm
Operating ragne
1400-2300
Overall length
3335 mm
Injection pump timing
15.75 ± 1° BTDC
Overall width
1650 mm
Overall height (with exhaust pipe)
2205 mm
Ground clearance
365 mm
Turning radius w. brake
2840 mm
Turning radius w/o brake
3210 mm
Dimensions and Weight
Electrical
Battery
12 V, 88 Ah
Alternator
43 Amp
Starter
12 V, 2.5 kW
Filling capacities
Transmission
Clutch type
single clutch / Dual
Gearbox type
Collar Shift
No. of forward gears
8
No. of reverse gears
4
PTO speed
540 rpm
Fuel tank
62 lit
Engine sump
8.5 lit
Transmission
33 lit
Hydraulics
Common to transmission
Brakes
Type
Wet disc brakes
Actuation
Mechanical
PY80265,05GO996 –19–15JAN07–1/1
155-3
022607
PN=171
Specifications
John Deere 5203 Tractor
5203—3029D Naturally Aspirated Engine
Observed PTO power
Hydraulics
32.5 kW (44.21 PS)
Pump output
25.7 l/min
Max. engine torque
165 N.m
Lifting capacity
1550 Kgf
Cylinders
3
Bore
106.5 mm
Wheels and Tyres
Stroke
110 mm
Front tyre
Displacement
2.9 L
Rear tyre
Compression ratio
17.8:1
6.0 x 16, 8 PR
13.6 x 28, 12 PR
14.9 x 28, 12 PR (optional)
Firing order
1-2-3
Slow idle
850±25
Total weight
1835 kg
Fast idle
2485±25
Wheel base
1950 mm
Operating range
1400-2300
Overall lenght
3360 mm
Injection pump timing
15.5 ± 1° BTDC
Overall width
1790 mm
Overall height (with exhaust pipe)
2215 mm
Ground clearance
420 mm
Turning radius w. brake
2900 mm
Turning radius w/o brake
3220 mm
Dimensions and Weight
Electrical
Battery
12 V, 88 Ah
Alternator
43 Amp
Starter
12 V, 2.5 kW
Filling capacities
Transmission
Fuel tank
62 lit
Dual (Optional single
clutch)
Engine sump
8.5 lit
Gearbox type
Collar Shift
Transmission
No. of forward gears
8
No. of reverse gears
4
33 lit with Rear Tyre Size
13.6 X 28, 12 PR
34 lit with Rear Tyre Size
14.9 X 28, 12PR
PTO speed
540 rpm
Hydraulics
Common to transmission
Clutch type
Brakes
Type
Wet disc brakes
Actuation
Mechanical
PY80265,05GO997 –19–17JAN07–1/1
155-4
022607
PN=172
Specifications
John Deere 5104 Tractor
5104—3029D Naturally Aspirated Engine
Observed PTO power
Brakes
28.09 kW (38.2 hp)
Type
Wet disc brakes
Max. engine torque
157 N.m
Actuation
Mechanical
Cylinders
3
Bore
106.5 mm
Hydraulics
Stroke
110 mm
Pump output
Displacement
2.9 L
Lifting capacity
Compression ratio
17.8:1
Firing order
1-2-3
Slow idle
800 - 875
Fast idle
2475 - 2550
Operating ragne
1200-2300
Injection pump timing
14.2 ± 1° BTDC
12 V, 88 Ah
Alternator
40 Amp
Starter
12 V, 2.5 kW
Single / Dual
Gearbox type
Collar Shift
No. of forward gears
8
No. of reverse gears
4
PTO speed
540 rpm
Front tyre
6.0 x 16, 8 PR
Rear tyre
13.6 x 28, 12 PR
Dimensions and Weight
Transmission
Clutch type
1400 Kgf
Wheels and Tyres
Electrical
Battery
46 l/min
Total weight
1800 kg
Wheel base
1950 mm
Overall length
3335 mm
Overall width
1650 mm
Overall height (with exhaust pipe)
2205 mm
Ground clearance
365 mm
Turning radius w. brake
2840 mm
Turning radius w/o brake
3210 mm
Filling capacities
Fuel tank
62 lit
Engine sump
8.5 lit
Transmission
33 lit
Hydraulics
Common to transmission
PY80265,00001DA –19–19JAN07–1/1
155-5
022607
PN=173
Specifications
John Deere 5204 Tractor
5204—3029D Naturally Aspirated Engine
Observed PTO power
Hydraulics
31.33 kW (42.6 hp)
Pump output
25.7 l/min for Manual
Steering
46 l/min for Power Steering
Lifting capacity
1550 Kgf
Max. engine torque
180.4 N.m
Cylinders
3
Bore
106.5 mm
Stroke
110 mm
Displacement
2.9 L
Front tyre
6.0 x 16, 8 PR
Compression ratio
17.8:1
Rear tyre
14.9 x 28, 12 PR
Firing order
1-2-3
Slow idle
800 - 875
Fast idle
2475 - 2550
Total weight
1835 kg
Operating range
1200-2300
Wheel base
1940 mm
Injection pump timing
15.2 ± 1° BTDC
Overall lenght
3360 mm
Overall width
1790 mm
Wheels and Tyres
Dimensions and Weight
Electrical
Overall height (with exhaust pipe)
2215 mm
Battery
12 V, 88 Ah
Ground clearance
420 mm
Alternator
40 Amp
Turning radius w. brake
2900 mm
Starter
12 V, 2.5 kW
Turning radius w/o brake
3220 mm
Transmission
Filling Capacities
Clutch type
Single / Dual
Fuel tank
62 lit
Gearbox type
Collar Shift
Engine sump
8.5 lit
No. of forward gears
8
Transmission
34 lit
No. of reverse gears
4
Hydraulics
Common to transmission
PTO speed
540 rpm
Brakes
Type
Wet disc brakes
Actuation
Mechanical
PY80265,00001D9 –19–17JAN07–1/1
155-6
022607
PN=174
Specifications
Ground Speed at Rated Engine Speed (2300 rpm)
5103E Tractor ( Rear tyre size : 12.4 x 28), ( RR - 590 mm )
Gear
Speed (km/h)
A1
2.80
5103S, 5203 and 5104 Tractor ( Rear tyre size : 13.6 x 28), (
RR - 610 mm )
Gear
Speed (km/h)
2.9
A2
4.06
A1
A3
6.09
A2
4.2
A4
9.96
A3
6.3
B1
8.41
A4
10.3
B2
12.09
B1
8.7
B3
18.18
B2
12.5
29.69
B3
18.8
R1
3.77
B4
30.7
R2
5.32
R1
3.9
R2
5.5
R3
8.4
R4
13.7
B4
R3
8.12
R4
13.25
5103 Tractor ( Rear tyre size : 12.4 x 28), ( RR - 590 mm )
Gear
Speed (km/h)
A1
2.80
A2
4.06
A3
6.09
A4
9.96
B1
8.41
B2
12.09
B3
18.18
B4
29.69
R1
3.77
R2
5.32
R3
8.12
R4
13.25
5203 and 5204 Tractor ( Rear tyre size : 14.9 x 28), ( RR - 640
mm )
Gear
Speed (km/h)
A1
3.06
A2
4.38
A3
6.60
A4
10.80
B1
9.11
B2
13.06
B3
19.67
B4
32.15
R1
4.06
R2
5.82
R3
8.76
R4
14.31
PY80265,05GO998 –19–29DEC06–1/1
155-7
022607
PN=175
Specifications
TORQ2
–UN–07SEP99
Metric Bolt and Cap Screw Torque Values
Top, Property Class and Head Markings; Bottom, Property Class and Nut Markings
Class 4.8
Size
Lubricated
N•m(lb-ft)
a
Class 8.8 or 9.8
b
Dry
N•m(lb-ft)
a
Class 10.9
b
Lubricated
N•m(lb-ft)
Dry
N•m(lb-ft)
a
Class 12.9
b
Lubricated
N•m(lb-ft)
Dry
N•m(lb-ft)
Lubricateda
N•m(lb-ft)
Dryb
N•m(lb-ft)
M6
4.7 (3.5)
6 (4.4)
9 (6.6)
11.5 (8.5)
13 (9.5)
16.5 (12.2)
15.5 (11.5)
19.5 (14.5)
M8
11.5 (8.5)
14.5 (10.7)
22 (16)
28 (20.5)
32 (23.5)
40 (29.5)
37 (27.5)
47 (35)
M10
23 (17)
29 (21)
43 (32)
55 (40)
63 (46)
80 (59)
75 (55)
95 (70)
M12
40 (29.5)
50 (37)
75 (55)
95 (70)
110 (80)
140 (105)
130 (95)
165 (120)
M14
63 (46)
80 (59)
120 (88)
150 (110)
175 (130)
220 (165)
205 (150)
260 (190)
M16
100 (74)
125 (92)
190 (140)
240 (175)
275 (200)
350 (255)
320 (235)
400 (300)
M18
135 (100)
170 (125)
265 (195)
330 (245)
375 (275)
475 (350)
440 (325)
560 (410)
M20
190 (140)
245 (180)
375 (275)
475 (350)
530 (390)
675 (500)
625 (460)
790 (580)
M22
265 (195)
330 (245)
510 (375)
650 (480)
725 (535)
920 (680)
850 (625)
1080 (800)
M24
330 (245)
425 (315)
650 (480)
820 (600)
920 (680)
1150 (850)
1080 (800)
1350 (1000)
M27
490 (360)
625 (460)
950 (700)
1200 (885)
1350 (1000)
1700 (1250)
1580 (1160)
2000 (1475)
M30
660 (490)
850 (625)
1290 (950)
1630 (1200)
1850 (1350)
2300 (1700)
2140 (1580)
2700 (2000)
M33
900 (665)
1150 (850)
1750 (1300)
2200 (1625)
2500 (1850)
3150 (2325)
2900 (2150)
3700 (2730)
M36
1150 (850)
1450 (1075)
2250 (1650)
2850 (2100)
3200 (2350)
4050 (3000)
3750 (2770)
4750 (3500)
a
"Lubricated" means coated with a lubricant such as engine oil, or fasteners with phosphate and oil coatings.
b
"Dry" means plain or zinc plated without any lubrication.
DO NOT use these values if a different torque value or tightening
procedure is given for a specific application. Torque values listed are
for general use only. Check tightness of fasteners periodically.
Make sure fastener threads are clean and that you properly start
thread engagement. This will prevent them from failing when
tightening.
Shear bolts are designed to fail under predetermined loads. Always
replace shear bolts with identical property class.
Tighten plastic insert or crimped steel-type lock nuts to approximately
50 percent of the dry torque shown in the chart, applied to the nut,
not to the bolt head. Tighten toothed or serrated-type lock nuts to the
full torque value.
Fasteners should be replaced with the same or higher property class.
If higher property class fasteners are used, these should only be
tightened to the strength of the original.
PY80265,05GO999 –19–10SEP05–1/1
155-8
022607
PN=176
Specifications
TORQ1A
–UN–27SEP99
Unified Inch Bolt and Cap Screw Torque Values
Top, SAE Grade and Head Markings; Bottom, SAE Grade and Nut Markings
Grade 1 (No Mark)
Size
Lubricated
N•m(lb-ft)
b
c
Grade 2a (No Mark)
b
Dry
N•m(lb-ft)
Lubricated
N•m(lb-ft)
c
Dry
N•m(lb-ft)
Grade 5, 5.1 or 5.2
b
Lubricated
N•m(lb-ft)
c
Grade 8 or 8.2
Dry
N•m(lb-ft)
Lubricatedb
N•m(lb-ft)
Dryc
N•m(lb-ft)
1/4
3.8 (2.8)
4.7 (3.5)
6 (4.4)
7.5 (5.5)
9.5 (7)
12 (9)
13.5 (10)
17 (12.5)
5/16
7.7 (5.7)
9.8 (7.2)
12 (9)
15.5 (11.5)
19.5 (14.5)
25 (18.5)
28 (20.5)
35 (26)
3/8
13.5 (10)
17.5 (13)
22 (16)
27.5 (20)
35 (26)
44 (32.5)
49 (36)
63 (46)
7/16
22 (16)
28 (20.5)
35 (26)
44 (32.5)
56 (41)
70 (52)
80 (59)
100 (74)
1/2
34 (25)
42 (31)
53 (39)
67 (49)
85 (63)
110 (80)
120 (88)
155 (115)
9/16
48 (35.5)
60 (45)
76 (56)
95 (70)
125 (92)
155 (115)
175 (130)
220 (165)
5/8
67 (49)
85 (63)
105 (77)
135 (100)
170 (125)
215 (160)
240 (175)
305 (225)
3/4
120 (88)
150 (110)
190 (140)
240 (175)
300 (220)
380 (280)
425 (315)
540 (400)
7/8
190 (140)
240 (175)
190 (140)
240 (175)
490 (360)
615 (455)
690 (510)
870 (640)
1
285 (210)
360 (265)
285 (210)
360 (265)
730 (540)
920 (680)
1030 (760)
1300 (960)
1-1/8
400 (300)
510 (375)
400 (300)
510 (375)
910 (670)
1150 (850)
1450 (1075)
1850 (1350)
1-1/4
570 (420)
725 (535)
570 (420)
725 (535)
1280 (945)
1630 (1200)
2050 (1500)
2600 (1920)
1-3/8
750 (550)
950 (700)
750 (550)
950 (700)
1700 (1250)
2140 (1580)
2700 (2000)
3400 (2500)
1-1/2
990 (730)
1250 (930)
990 (730)
1250 (930)
2250 (1650)
2850 (2100)
3600 (2650)
4550 (3350)
a
Grade 2 applies for hex cap screws (not hex bolts) up to 6 in. (152 mm) long. Grade 1 applies for hex cap screws over 6 in. (152 mm) long,
and for all other types of bolts and screws of any length.
b
"Lubricated" means coated with a lubricant such as engine oil, or fasteners with phosphate and oil coatings.
c
"Dry" means plain or zinc plated without any lubrication.
DO NOT use these values if a different torque value or tightening
procedure is given for a specific application. Torque values listed are
for general use only. Check tightness of fasteners periodically.
Make sure fastener threads are clean and that you properly start
thread engagement. This will prevent them from failing when
tightening.
Shear bolts are designed to fail under predetermined loads. Always
replace shear bolts with identical grade.
Tighten plastic insert or crimped steel-type lock nuts to approximately
50 percent of the dry torque shown in the chart, applied to the nut,
not to the bolt head. Tighten toothed or serrated-type lock nuts to the
full torque value.
Fasteners should be replaced with the same or higher grade. If
higher grade fasteners are used, these should only be tightened to
the strength of the original.
PY80265,05G1101 –19–10SEP05–1/1
155-9
022607
PN=177
Identification Numbers
Identification Plates
Each tractor has the identification plates shown on these
pages. The letters and numbers stamped on the plates
identify a component or assembly. ALL these characters
are needed when ordering parts or identifying a tractor or
component for any John Deere product support program.
Also, they are needed for law enforcement to trace your
tractor if it is ever stolen. ACCURATELY record these
characters in the spaces provided in each of the following
photographs.
PY80265,05G1102 –19–10SEP05–1/1
Record Tractor Serial (Chassis) Number
Serial number plate (A) is located on the right front
support member of the tractor.
PY5166
–UN–24AUG05
Tractor Serial Number
PY80265,05G1103 –19–10SEP05–1/1
160-1
022607
PN=178
Identification Numbers
Record Front Axle Serial Number
The front-axle serial number plate (A) is located on the
right rear side of the axle housing.
PY1730
–UN–01JUN06
Front Axle Serial Number
PY1722
–UN–01JUN06
CARRARO Front Axle
DANA Front Axle
PY80265,05G1104 –19–10SEP05–1/1
Record Engine Serial Number
–UN–21AUG05
Serial number plate (A) is located on the right-hand side
of the engine block between the starter solenoid and the
hydraulic pump.
PY5154
Engine Serial Number
PY80265,05G1105 –19–10SEP05–1/1
160-2
022607
PN=179
Identification Numbers
Record Transmission Serial Number
Transmission serial number is stamped into the lower
left-hand corner of rear housing (A).
–UN–03SEP04
Transmission shield is removed for better quality of picture
PY4178
Transmission Serial Number
Transmission Serial number
NR25796,0000358 –19–04AUG06–1/1
160-3
022607
PN=180
Lubrication Maintenance Record Charts
50, 250 Hour Service Chart
Every 50 Hours
•
•
•
•
•
•
Check transmission-hydraulic system oil level
Clean and check battery
Inspect all tyres
Lubricate front axle pivot pin
Lubricate steering spindles
Inspect tractor for loose nuts and bolts
•
•
•
•
•
•
•
Service air cleaner
Inspect and adjust alternator/fan belt
Lubricate 3-point hitch
Check neutral start system
Check clutch pedal free play
Check brake pedal adjustment
Change primary and secondary filter inserts
alternatively
Every 250 Hours
• Change engine oil and filter
Hours
Hours
Date
Date
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
PY80265,05G1107 –19–10SEP05–1/1
165-1
022607
PN=181
Lubrication Maintenance Record Charts
500,600 Hour Service Chart
Every 500 Hours
• Replace transmission-hydraulic filter
Every 600 Hours
•
•
•
•
•
• Clean crankcase vent tube
• Repack front wheel bearings
Hours
Tighten engine air intake hose clamps
Check cooling system for leaks
Lubricate rear axle bearings
Check engine idle speeds
Have your John Deere dealer:
– Adjust engine valve clearance
– Check front axle pivot pin
– Inspect fuel injectors
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
PY80265,05G1108 –19–10SEP05–1/1
165-2
022607
PN=182
Lubrication Maintenance Record Charts
1000, 1250 Hour Service Chart
Every 1000 Hours
Every 1250 Hours
• Check and adjust valve clearance
• Check engine speeds
• Change transmission-hydraulic oil and filter
• Clean transmission-hydraulic pickup screen
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
PY80265,05G1109 –19–10SEP05–1/1
165-3
022607
PN=183
Lubrication Maintenance Record Charts
Annual Service Chart
Annually
• Replace air cleaner elements
• Change engine oil and filter
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
PY80265,05G1110 –19–10SEP05–1/1
165-4
022607
PN=184
Lubrication Maintenance Record Charts
2000 Hour Service Chart
Every 2 Years or 2000 Hours (Whichever Comes
First)
• Flush cooling system
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
PY80265,05G1111 –19–10SEP05–1/1
165-5
022607
PN=185
Lubrication Maintenance Record Charts
As Required Service Chart
Service as Required
• Replace fuel filter
• Drain water and sediment from fuel tank
• Service air cleaner
• Adjust throttle friction
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
Hours
Hours
Date
Date
PY80265,05G1112 –19–10SEP05–1/1
165-6
022607
PN=186
John Deere Service
John Deere Parts
TS100
–UN–23AUG88
We help minimize downtime by putting genuine John
Deere parts in your hands in a hurry. That’s why we
maintain a large and varied inventory to meet your spare
parts needs.
PY00013,0000003 –19–14JUN01–1/1
The Right Tools
TS101
–UN–23AUG88
Precision tools and testing equipment enable our Service
Department to locate and correct troubles quickly. They
save your time and money.
PY00013,0000004 –19–14JUN01–1/1
Well Trained Technician
School is never out for John Deere service technicians.
Training schools are held regularly to be sure our
personnel know your equipment and how to maintain it.
–UN–23AUG88
Result?
TS102
Experience you can count on!
PY00013,0000005 –19–14JUN01–1/1
Prompt Service
TS103
see us, depend on us.We’ll be around when you need us.
–UN–23AUG88
Our goal is to provide prompt, efficient care when you
want it and where you want it. We can make repairs at
your place or at ours, depending on the circumstances.
PY00013,0000006 –19–14JUN01–1/1
170-1
022607
PN=187
John Deere Service
170-2
022607
PN=188
Index
Page
A
Acid burns, battery . . . . . . . . . . . . . . . . . . . . . 140-18
Adjusting rockshaft speed-of-drop
Implement lock . . . . . . . . . . . . . . . . . . . . . . . . 55-5
Air cleaner
Inspecting primary element . . . . . . . . . . . . . . 140-9
Replace elements . . . . . . . . . . . . . . . . . . . . . 125-1
Service . . . . . . . . . . . . . . . . . . . . . . . .110-1, 135-1
Service/regular intervals . . . . . . . . . . . . . . . . 140-6
Storing primary element . . . . . . . . . . . . . . . 140-10
Air intake system
Checking. . . . . . . . . . . . . . . . . . . . . . . . . . . . 140-7
Components . . . . . . . . . . . . . . . . . . . . . . . . . 140-5
Air restriction indicator . . . . . . . . . . . . . . . .45-4, 45-5
Alternator wiring
Connecting . . . . . . . . . . . . . . . . . . .140-21, 140-22
Alternator/fan belt
Inspect and adjust. . . . . . . . . . . . . . . . . . . . . 110-2
Alternator/fan belt, replacing . . . . . . . . . . . . . . 140-10
Attaching implements to three point hitch . . . . . . 55-8
Attaching PTO-driven implement . . . . . . . . . . . . 65-2
B
Ballast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-1
Limitations. . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-3
Liquid weight. . . . . . . . . . . . . . . . . . . . . . . . . . 70-6
Matching to load work . . . . . . . . . . . . . . . . . . . 70-1
Maximum front . . . . . . . . . . . . . . . . . . . . . . . . 70-5
Maximum rear. . . . . . . . . . . . . . . . . . . . . . . . . 70-5
Selecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-1
Ballasting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-4
Front end for transport . . . . . . . . . . . . . .70-3, 70-4
Battery
Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140-15
Acid burn treatment. . . . . . . . . . . . . . . . . . . 140-18
Booster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45-11
Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . 140-20
Checking condition . . . . . . . . . . . . . . . . . . . 140-17
Clean and check . . . . . . . . . . . . . . . . . . . . . . 100-1
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . 140-16
Replacement specifications. . . . . . . . . . . . . 140-20
Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . 140-18
Battery explosion . . . . . . . . . . . . . . . . . . . . . . 140-17
Before starting the engine . . . . . . . . . . . . . . . . . 45-1
Bolts
Front axle, tighten . . . . . . . . . . . . . . . . . . . . . . 75-3
Rear axle, tighten . . . . . . . . . . . . . . . . . .75-5, 75-6
Booster battery . . . . . . . . . . . . . . . . . . . . . . . . . 45-11
Page
Brake pedal free play
Check and adjust . . . . . . . . . . . . . . . . . . . . . 110-5
Brakes
Using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-6
Brakes troubleshooting . . . . . . . . . . . . . . . . . . . 145-5
Break-in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35-1
Break-in service . . . . . . . . . . . . . . . . . . . . .35-2, 90-1
C
Cast iron weights . . . . . . . . . . . . . . . . . . . . . . . . 70-5
Install rear. . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-6
Center link
Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . 55-7
Charging system indicator . . . . . . . . . . . . . . . . . 45-4
Checking Toe-In . . . . . . . . . . . . . . . . . . . . . . . . . 75-9
Clutch pedal free play
Check and adjust . . . . . . . . . . . . . . . . . . . . . 110-4
Coolant
Check level . . . . . . . . . . . . . . . . . . . . . . . . . . . 95-1
Diesel engine . . . . . . . . . . . . . . . . . . . . . . . . . 85-5
Coolant temperature gauge . . . . . . . . . . . . . . . . 45-5
Cooling system
Components . . . . . . . . . . . . . . . . . . . . . . . . 140-13
Flush every two years . . . . . . . . . . . . . . . . . . 130-1
D
Dash panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diesel engine
Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential lock
Using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Draft control, using . . . . . . . . . . . . . . . . . . . . . . .
Drawbar
Load limitations . . . . . . . . . . . . . . . . . . . . . . . .
Driving on public roads . . . . . . . . . . . . . . . .50-1,
15-3
85-4
50-7
55-4
65-1
80-1
E
Electrical service precautions . . . . . . . . . . . . . 140-15
Electrical system troubleshooting . . . . . . . . . . . 145-8
Engine
Avoid idling . . . . . . . . . . . . . . . . . . . . . . . . . . . 45-8
Break-in oil . . . . . . . . . . . . . . . . . . . . . . . . . . 140-3
Change oil and filter . . . . . . . . . . . . . . . . . . . 110-1
Changing speeds . . . . . . . . . . . . . . . . . . . . . . 45-7
Index-1
022607
PN=1
Index
Page
Page
Check idle speeds . . . . . . . . . . . . . . . . . . . . 115-4
Check oil level . . . . . . . . . . . . . . . . . . . . . . . . 95-1
Observe work and idle speeds . . . . . . . . . . . . 45-9
Stalled. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45-8
Stopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45-10
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . 145-1
Warming up . . . . . . . . . . . . . . . . . . . . . . . . . . 45-7
Engine crankcase vent tube
Clean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115-1
Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-2
Adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . 140-27
Aiming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140-26
Replace bulb. . . . . . . . . . . . . . . . . . . . . . . . 140-28
High beam indicator . . . . . . . . . . . . . . . . . . . . . . 20-2
Hitch
Adjusting side sway . . . . . . . . . . . . . . . . . . . . 55-9
Components . . . . . . . . . . . . . . . . . . . . . . . . . . 55-1
Leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55-10
Lubricate three-point . . . . . . . . . . . . . . . . . . . 110-3
Hood
Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140-4
Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . 140-5
Hoses and hose clamps, check . . . . . . . . . . . . 115-2
Hydraulic system troubleshooting . . . . . . . . . . . 145-5
Hydraulic-transmission filter element . . . . . . . . . 85-6
F
Fan/alternator belt, replacing . . . . . . . . . . . . . 140-10
Front axle pivot pin
Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115-4
Lubricate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100-2
Front wheel bearings, pack . . . . . . . . . . . . . . . 115-1
Fuel
Fill tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85-3
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85-2
Watch level . . . . . . . . . . . . . . . . . . . . . . . . . . . 45-6
Fuel filter
Drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95-2
filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110-2
Fuel system
Bleeding fuel injection nozzles . . . . . . . . . . 140-12
Bleeding (MICO injection pump) . . . . . . . . . 140-12
Components . . . . . . . . . . . . . . . . . . . . . . . . 140-11
Fuels and lubricants . . . . . . . . . . . . . . . . . . . . . . 85-1
Fuses
Locating . . . . . . . . . . . . . . . . . . . . . . . . . . . 140-23
Size and function . . . . . . . . . . . . . .140-24, 140-25
Fusible link, locating . . . . . . . . . . . . . . . . . . . . 140-22
G
Gauge
Coolant temperature . . . . . . . . . . . . . . . . . . . . 45-5
Gear oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85-6
Grease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85-7
Grille screens, cleaning . . . . . . . . . . . . . . . . . 140-14
Ground speed estimates. . . . . . . . . . . . . . . . . . 155-7
I
Identification numbers. . . . . . . . . . . . . . . . . . . . 160-1
Idle speeds, check . . . . . . . . . . . . . . . . . . . . . . 115-4
Implement to tire clearance . . . . . . . . . . . . . . . . 75-1
Inch torque values . . . . . . . . . . . . . . . . . . . . . . 155-9
Indicator
Air restriction. . . . . . . . . . . . . . . . . . . . . .45-4, 45-5
Charging system . . . . . . . . . . . . . . . . . . . . . . . 45-4
Oil pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 45-3
Instrument panel. . . . . . . . . . . . . . . . . . . . . . . . . 15-3
L
Lateral float, adjusting . . . . . . . . . . . . . . . . . . . 55-11
Light
Hazard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-5
Light switch
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-1
Lighting and signals . . . . . . . . . . . . . . . . . . . . . . 20-1
Lubricant
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85-4
Lubrication and maintenance record charts . . . 165-1
H
M
Hardware
Wheel/axle, tighten . . . . . . . . . . . . . . . . . . . . . 75-3
Metric torque values . . . . . . . . . . . . . . . . . . . . . 155-8
Index-2
022607
PN=2
Index
Page
N
Neutral start system, check . . . . . . . . . . . . . . . 110-3
O
Oil
Engine break-in. . . . . . . . . . . . . . . . . . . . . . . 140-3
Warming hydraulic system . . . . . . . . . . . . . . 55-12
Oil cooler, cleaning. . . . . . . . . . . . . . . . . . . . . 140-14
Oil Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85-6
Oil pressure indicator . . . . . . . . . . . . . . . . . . . . . 45-3
Operating transmission. . . . . . . . . . . . . . . .50-3, 50-4
Operator training . . . . . . . . . . . . . . . . . . . . . . . . 50-1
Page
10 hours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95-1
100 hours . . . . . . . . . . . . . . . . . . . . . . . . . . . 110-1
1200 hours . . . . . . . . . . . . . . . . . . . . . . . . . . 120-1
250 hours . . . . . . . . . . . . . . . . . . . . . . . . . . . 110-1
50 hours . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100-1
Service intervals . . . . . . . . . . . . . . . . . . . . . . . . . 90-2
Service intervals, observe. . . . . . . . . . . . . . . . . . 90-1
Seven-terminal outlet . . . . . . . . . . . . . . . . . . . . . 20-6
Side screens, removing . . . . . . . . . . . . . . . . . . 140-4
Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-1
Speed/hour meter. . . . . . . . . . . . . . . . . . . . . . . . 45-9
Starter wiring, connecting . . . . . . . . . . . . . . . . 140-21
Starting the engine . . . . . . . . . . . . . . . . . . . . . . . 45-2
Steering spindles, lubricate. . . . . . . . . . . . . . . . 100-2
Stopping tractor . . . . . . . . . . . . . . . . . . . . . . . . . 50-8
Storing lubricants . . . . . . . . . . . . . . . . . . . . . . . . 85-4
Storing tractor. . . . . . . . . . . . . . . . . . . . . . . . . . 150-1
P
Position center link . . . . . . . . . . . . . . . . . . . . . . .
Position control lever stop, setting . . . . . . . . . . .
Prestart checks. . . . . . . . . . . . . . . . . . . . . . . . . .
PTO
Adjusting clutch rod. . . . . . . . . . . . . . . . . . . . .
Attach driven implement . . . . . . . . . . . . . . . . .
Operating . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55-7
55-2
40-1
65-5
65-2
65-3
R
Radiator, cleaning. . . . . . . . . . . . . . . . . . . . . . 140-14
Rear axle bearings, lubricate . . . . . . . . . . . . . . 115-3
Removing tractor from storage . . . . . . . . . . . . . 150-4
Ride comfort, adjusting. . . . . . . . . . . . . . . . . . . . 25-1
Rockshaft
Postion control . . . . . . . . . . . . . . . . . . . . . . . . 55-3
Rate-of-drop adjustment . . . . . . . . . . . . . . . . . 55-5
Rockshaft and quick-coupler 3-point hitch
troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 145-6
Rockshaft control lever friction, adjust . . . . . . . 55-11
Rockshaft control levers . . . . . . . . . . . . . . . . . . . 55-2
S
Seat
Selecting position . . . . . . . . . . . . . . . . . . . . . . 25-1
Selecting a gear . . . . . . . . . . . . . . . . . . . . . . . . . 50-5
Service
As required . . . . . . . . . . . . . . . . . . . . . . . . . . 135-1
T
Tail light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-3
Replace bulb. . . . . . . . . . . . . . . . . . . . . . . . 140-29
Three-point hitch, lubricate . . . . . . . . . . . . . . . . 110-3
Throttle friction, adjust . . . . . . . . . . . . . . . . . . . 135-1
Tires
Checking. . . . . . . . . . . . . . . . . . . . . . . . . . . 140-30
Inflation pressure . . . . . . . . . . . . . . . . . . . . . . 75-2
Inflation pressure chart . . . . . . . . . . . . . . . . . . 75-3
Toe-in
Adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75-10
Toe-in, 2-WD tractor
Adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75-11
Torque values
Adjustable front axle . . . . . . . . . . . . . . . . . . . . 75-3
Inch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155-9
Metric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155-8
Rear axle . . . . . . . . . . . . . . . . . . . . . . . .75-5, 75-6
Wheels/axles. . . . . . . . . . . . . . . . . . . . . . . . . . 75-3
Towing tractor . . . . . . . . . . . . . . . . . . . . . . . . . . 80-4
Tractor controls . . . . . . . . . . . . . . . . . . . . . . . . . 15-1
Tractor PTO, operating. . . . . . . . . . . . . . . . . . . . 65-3
Transmission troubleshooting . . . . . . . . . . . . . . 145-4
Transmission, operating . . . . . . . . . . . . . . .50-3, 50-4
Transmission, shifting . . . . . . . . . . . . . . . . . . . . . 50-3
Transmission-hydraulic system
Change oil and filter . . . . . . . . . . . . . . . . . . . 120-1
Check oil level . . . . . . . . . . . . . . . . . . . . . . . 100-1
Clean pickup screen . . . . . . . . . . . . . . . . . . . 120-2
Replace filter. . . . . . . . . . . . . . . . . . . . . . . . . 112-1
Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80-4
Index-3
022607
PN=3
Index
Page
Tractor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05-7
Tread settings
Adjustable front axle . . . . . . . . . . . . . . . . . . . . 75-8
Multi-position rear wheels . . . . . . . . . . . . . . . . 75-7
Tread width
Rear wheel limitations . . . . . . . . . . . . . . . . . . . 75-6
Troubleshooting
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145-5
Electrical system . . . . . . . . . . . . . . . . . . . . . . 145-8
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145-1
Hydraulic system. . . . . . . . . . . . . . . . . . . . . . 145-5
Quick-coupler 3-point hitch . . . . . . . . . . . . . . 145-6
Rockshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . 145-6
Transmission. . . . . . . . . . . . . . . . . . . . . . . . . 145-4
Turn signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-4
U
Using
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cast iron weights . . . . . . . . . . . . . . . . . . . . . .
Differential lock . . . . . . . . . . . . . . . . . . . . . . . .
Draft control . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tail lights . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn signals . . . . . . . . . . . . . . . . . . . . . . . . . .
50-6
70-5
50-7
55-4
20-2
20-3
20-4
W
Warming hydraulic system oil . . . . . . . . . . . . . . 55-12
Warning light
Replace bulb. . . . . . . . . . . . . . . . . . . . . . . . 140-29
Weights
Cast iron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-5
Install rear cast iron . . . . . . . . . . . . . . . . . . . . 70-6
Wheel slip
Measuring manually . . . . . . . . . . . . . . . . . . . . 70-2
Index-4
022607
PN=4
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.1 Linearized : No Page Count : 194 Page Mode : UseOutlines Create Date : 1910:70:22 60:45:52 Producer : Acrobat Distiller Command 3.02b for Solaris 2.3 and later (SPARC) Author : Deere & Company Deere & Company Creator : SYSTEM400 Rev 16.03 Title : 043025UNITEXIF Metadata provided by EXIF.tools